DRW170794AA

Specifications Measurement Input [PA 1 group : IN-R]

SMALL MULTI PANEL METER
Model M4NN-DV-1 M4NN-DA-1 M4NN-AV-1 M4NN-AA-1 Measured input Input Display range
Type Display Note
Measurement input DC Voltage DC Current AC Voltage, Frequency AC Current, Frequency range impedance [SㅊTㅍㅀㄷㄳㅅNㅜㅜD]

M4NN SERIES
-110 to 110% of each measured input range -600-600V 600V 4.694MΩ -600 to 600 ※For DC input, not to display minus
Max. allowable input (when not using minus input: -10 to 110%) Approx. 110% of each measured input range input, set minus input [MINU] of
-200-200V 200V 4.694MΩ -199.9 to 200.0
Power supply 5-24VDCᜡ -100-100V 100V 794kΩ -100.0 to 100.0 parameter 1 group as OFF.
E.g.) W
 hen the display range is -600
Allowable voltage range 90 to 110% of the rated voltage (5V is fixed for lower limit) DC -20-20V 20V 794kΩ -19.99 to 20.00
INSTRUCTION MANUAL Power consumption Max. 3W Voltage -10-10V 10V 79kΩ -10.00 to 10.00
to 600V, set MINU of parameter 1
group as OFF and this display range
Display method 7 Segment LED Display(red), Character height : 11mm -2-2V 2V 79kΩ -1.999 to 2.000 is 0 to 600V.
In 23±5℃ - DC type: ±0.1% F.S. ±2digit, AC type : ±0.3% F.S. ±3digit -1-1V 1V 7.5kΩ -1.000 to 1.000
-200-200mV 7.5kΩ -199.9 to 200.0 DOT Display range
5A terminal of DA, AA type: Within ±0.3% F.S. ±3digit )2V
Display accuracy 0 -1999 to 9999
In -10 to 50℃ - DC/AC type: ±0.5% F.S. ±3digit, Frequency: ±0.5% F.S. ±3digit -5-5A 5A 0.01Ω -5.00 to 5.00
5A terminal of DA, AA type: Within ±1% F.S. ±3digit -2-2A 2A 0.01Ω -1.999 to 2.000 )0 -199.9 to 999.9
Display cycle 0.1 to 5.0 sec (selecatable by 0.1 sec) -1-1A 1A 0.1Ω -1.000 to 1.000 )00 -19.99 to 99.99
A/D conversion method Practical oversampling using successive approximation ADC -200-200mA )2A 0.1Ω -199.9 to 200.0 )000 -1.999 to 9.999
DC
Sampling cycle 50ms(resolution 1/12,000) 16.6ms(resolution 1/12,000) -100-100mA )1A 1.1Ω -100.0 to 100.0
Current (the setting range varies depending on
Max. display range -1999 to 9999(4 digit) -20-20mA 20MA 1.1Ω -19.99 to 20.00 the decimal point setting)
NPN/PNP open collector output: 4-20mA 4-20 1.1Ω 4.00 to 20.00
Preset output
※1
·Load voltage: max. 30VDCᜡ ·Load current: max. 100mA -10-10mA 10MA 11.1Ω -10.00 to 10.00 ※Connect to the input terminals whose
·Residual voltage: max. 1VDCᜡ(NPN), max. 2VDC(PNP) -2-2mA 11.1Ω -1.999 to 2.000 30% to 100% of the input range includs
Thank you for choosing our Autonics product. AC measurement
※2
- Average value(AVG) measurement
2MA
the max. value of the input range to
0-600V 600V 5.011MΩ 0.0 to to 600.0
Please read the following safety considerations before use. Frequency ※2 Measured range: 0.100 to 9999Hz 0-250V 250V 5.011MΩ 0.0 to 250.0 measure.
- When the max. input value is under the
measurement (variable by decimal point position) 0-110V ※110P 1.111MΩ 0.0 to 440.0
Safety Considerations Insulation resistance Over 100㏁(at 500VDC megger) AC 0-50V 50V 1.11MΩ 0.00 to 50.00
30% of the input terminal range, display
accuracy is degraded.
Dielectric strength 2000VAC for 1 minute (between all terminals and case) Voltage 0-20V 20V 224kΩ 0.00 to 20.00 When the max. input value is over the
※Please observe all safety considerations for safe and proper product operation to avoid hazards. 100%, it may result in input terminal
Noise immunity ±2kV the square wave noise(pulse width: 1㎲) by the noise simulator 0-10V 10V 224kΩ 0.00 to 10.00
※Safety considerations are categorized as follows. Mechanical 0.75mm amplitude at frequency of 10 to 55Hz(for 1 min) in each X, Y, Z direction for 2 hours 0-2V 2V 24kΩ 0.000 to 2.000 damage.
Vibration
Warning Failure to follow these instructions may result in serious injury or death. Malfunction 0.5mm amplitude at frequency of 10 to 55Hz(for 1 min) in each X, Y, Z direction for 10 minutes 0-1V 1V 24kΩ 0.000 to 1.000
※For the range setting of AC voltage,
Mechanical 100m/s2(approx. 10G) in each X, Y, Z direction for 3 times 0-5A 5A 0.01Ω 0.000 to 5.000 when setting as 0 to 110V [110P]
Caution Failure to follow these instructions may result in personal injury or product damage. Shock
Malfunction 300m/s2(approx. 30G) in each X, Y, Z direction for 3 times 0-2.5A @5A 0.01Ω 0.000 to 2.500 and using P.T for 440V/110VAC,
※The symbols used on the product and instruction manual represent the following 0-1A 1A 0.05Ω 0.000 to 1.000 110V is input and 440V is displayed
Ambient -10 to 50℃, storage: -20 to 60℃ 0-500mA 0.1Ω 0.0 to 500.0 automatically by the set scale value
symbol represents caution due to special circumstances in which hazards may occur. Environ temperature AC )5A
-ment Ambient Current 0-250mA )25A 0.1Ω 0.0 to 250.0 for P.T users' convenience.
Warning humidity 35 to 85%RH, storage: 35 to 85%RH 0-100mA )1A 0.5Ω 0.0 to 100.0
※Frequency measurement range
Connection type Plug/Socket terminal block (accessory) (AC voltage/current)
1. Fail-safe device must be installed when using the unit with machinery that may cause serious injury or 0-50mA 50MA 0.5Ω 0.00 to 50.00
substantial economic loss. (e.g. nuclear power control, medical equipment, ships, vehicles, railways, Double insulation or reinforced insulation : 0.100 to 9999Hz
Insulation type (mark: , Dielectric strength between the measuring input part and the power part : 1kV)
aircraft, combustion apparatus, safety equipment, crime/disaster prevention devices, etc.) ※When "HHHH" or "LLLL" is flashes with a certain measurement input, disconnect power supply and then check the cables.
Failure to follow this instruction may result in fire, personal injury, or economic loss. Approval
2. Install on a device panel to use.
Failure to follow this instruction may result in fire. Weight
※3 Approx. 83.6g
(approx. 46.8g)
Approx. 83.7g
(approx. 46.7g)
Approx. 83.8g
(approx. 46.9g)
Approx. 83.8g
(approx. 46.9g)
Display Cycle Delay [PA 2 group: DIsT]
3. Do not connect, repair, or inspect the unit while connected to a power source. ※1: Indicator model(M4NN- In some applications the measured input may fluctuate which in turn causes the display to fluctuate. By adjusting
-1N) does not have output function. the display cycle delay function time at DIsT of parameter 2 group, the operator can adjust the display time within
Failure to follow this instruction may result in fire. ※2: AC, Frequency measurement functions are only for AC measurement type.
4. Check 'Connections' before wiring. a range of 0.1 sec to 5 sec. For example, if the operator sets the display cycle time to 4.0 sec, the display value is
※3: The weight is with packaging and the weight in parenthesis is only unit weight. displayed the averaged input value over 4 sec in every 4 sec.
Failure to follow this instruction may result in fire.
※Environment resistance is rated at no freezing or condensation.
5. Do not disassemble or modify the unit.
Failure to follow this instruction may result in fire. Zero Adjustment Initialization
Prescale [PA1 group: H-SC/ L-SC] Forces the display value of measured input to 0(Zero).
Caution This function is to display setting(-1999 to 9999) of particular high/low-limit value in order to display High/Low- ● Zero adjustment range : -99 to 99
RUN mode
1. When connecting the power/measurement input, use AWG 24(0.20mm2) to AWG 20(0.50mm2) cable limit value of measurement input. If measurement inputs are 'a' and 'b' and particular values are 'A' and 'B', it will ● Zero adjustment method : Press and key M + + for over 5 sec
and tighten the terminal screw with a tightening torque of 0.74 to 0.90N.m. display a=A, b=B as below graphs. in RUN mode for 3 sec.
Failure to follow this instruction may result in fire or malfunction due to contact failure. Display Display Display Display Display + for 3 sec IN1 T NO YES
2. Use the unit within the rated specifications. value B value B value B value B value A )15 )00 M M
Failure to follow this instruction may result in fire or product damage. a b ※Flashes
A A When zero point adjustment with front key and hold terminal 0000 twice and
3. Use dry cloth to clean the unit, and do not use water or organic solvent. a b Input a b Input
a b Input a b Input A A value is finished normally, zero point of measurement terminal it returns
Failure to follow this instruction may result in fire. Input value
M4NN-DV/AV 600V to RUN
value value value B is displayed and the adjusted value is saved in INbL
4. Do not use the unit in the place where flammable/explosive/corrosive gas, humidity, direct sunlight, M4NN-DA/AA mode.
radiant heat, vibration, impact, or salinity may be present. automatically. 5A
Display Display a b Display Display B
Failure to follow this instruction may result in fire or explosion. value A value value A value ※In case of DC Voltage/ ※ If zero adjustment range is exceeded, the error [OVER] STND
5. Keep metal chip, dust, and wire residue from flowing into the unit. a b Current input model flashes twice and then move to RUN mode, maintaining
B A Input
Failure to follow this instruction may result in fire or product damage. value Input a b Input (M4NN-D - ) and previous setting value.
a b Input B B using minus input, they
value A
Ordering Information value
value are displayed.
Preset Output Mode [PA 2 group: OU!T/ OU@T]
Display scale function is able to change display value for min./max. measured input by setting high limit scale Mode Output operation Operation Mode Output operation Operation
H-SC and low limit scale L-SC in parameter 1 group.
M 4 N N DV 1 N E.g.) High limit scale value and low limit scale value setting (input range= 0-10V) Period ON :
Control OFF OUT1 No output OUT1.H Display value ≤ OU!L
N Indicator (without output function) L-SC= )00 L-SC= 1)00 L-SC= -%00 output No output
output OUT1.L Display value ≥ OU!H
1 NPN open collector output H-SC= %00,1)00,1%00, `)00 H-SC= `)00 H-SC= %00 HL Period OFF :
Hysterisis Period ON: OUT1
2 PNP open collector output Display value Display value Display value OUT1.H
Display value ≥ OU!H output Display value ≥ OU!L+ HYs1
Power supply 1%00 1%00 1%00 HI OUT1 Period OFF: Display value ≤ OU!H + HYs1
1 5-24VDC output Display value ≤ OU!H- HYs1
1)00 1)00 1)00 Period ON :
DV DC Voltage(minus input) Period ON: OUT1.H Display value ≤ OU!L
%00 %00 %00 OUT1.L Display value ≥ OU1H
Input DA DC Current(minus input) Display value ≤ OU!L HL-G
Input value Input value Input value LO OUT1.L
Period OFF : OUT1 Period OFF :
0 10V 0 10V 0 10V OUT1
AV AC Voltage output Display value ≥ OU!L+HYs1
output Display value ≤ OU!L - HYs1
AA AC Current -%00 Display value ≥ OU!H + HYs1
`)00 `)00 ※ Set output mode separately for each OUT1/OUT2.
Type ※ OUT1/OUT2 are operated individually depending on output operation mode.
N New type
※ Setting value mode of parameter 0 group is displayed depending on output operation mode.
Size ※When changing measured input, high limit scale value and low limit scale value are automatically changed as
N DIN W48×H24mm the default display range of the changed measured input. ※ GO outputs when the period both OUT1/OUT2 are off.(NPN/PNP open collector output type)
Digit
4 9999(4digit)
Error Correction [PA 1 group: INbH/ INbL] Parameter 0 Group Parameter 2 Group
Item
M Multi Meter It corrects display value error of measurement input. RUN mode RUN mode
INbL: -99 to 99 (adjust deviation of low-limit value) M M 3 sec M 4 sec
INbH: 0.100 to 9.999 (correct gradient of high-limit value)
Unit Descriptions Dimension 60.3
(unit: mm)
Display value=(Measured value × INbH) + INbL OU!H High-limit preset
value of OU!T
PA2
E.g.) When the measured range is 0 to 500V, and the display range is 0 to 500.0. If the low display value is !2 to M
5 6 7 8 50.5 Transistor M Set range:
0V input, set -12 as INbLvalue to display 0.0 by adjusting offset of the low-limit value. It is not displayed Preset output mode
48 output OU!T of OUT1 OFF, HI, LO, HL,
4 The display value to 500V measured input varies by adjusting the offset of low-limit value. If this display value when OUT1/2 preset M
terminal HL-G
2 is 50!0, calculate 500.0/501.0 (desired display value/the display value), and set the )998 correction value OU!L Low-limit preset output mode [OU!T,
M
Only displayed in
as the INbH to display 50)0 by adjusting gradient of high-limit value. value of OU!T
1 3 M OU@T] of parameter Preset output mode OUT1/2 output
※ The offset correction range of INbL is within -99 to 99 for D-0, D-1 digit regardless of decimal point position [DOT]. OU@T of OUT2
21.8

model
24

4 ※ High limit error correction function is available as “Gradient correction” and low limit error correction 2 group is OFF.
M
function is available as “Zero adjustment”. High-limit preset Set range: Set range: 10% F.S.
OU@H value of OU@T Refer to Input type Preset hysteresis of Not displayed when
HYs1 OUT1
1. Measured value display ※Indicator model (M4NN- -1N) does not Gradient Correction [PA 1 group: INbH] and range.
1.7

M preset output mode

M
2. M : MODE key have transistor output terminal. [OU!T,OU@T] of
●Bracket This function is to adjust gradient of standard display value or scale value for the input value within the measured Preset hysteresis of parameter 1 group
3. : Up key ●Panel cut-out Low-limit preset
42 input range. By adjusting gradient, it is available as “High limit error correction function”. OU@L value of OU@T HYs2 OUT2 is set as OFF.
4. : Shift key M
Min. 55 As the below(Figure 1), in case of display gradient 1 for the measured input 100V, this function is to adjust M
5. OUT1(Red): display value by adjusting the gradient as 1.5 times or 0.5 times. Monitoring delay time
OUT1 output indicator of preset • Set range: 0.100 to 9.999, factory default: 1.000 (unit: multiply) PEtT Set range: 00 to 30 sec
If monitoring delay time
22.2+0.3

6. GO(Green): Display value

36.3
28.8

M
0

E.g. 1) Gradient adjustment

22

hPEK Displays high peak [PEkT]of parameter 2 Display period

GO output indicator of preset ①When the measured input is 100.0V in order to display 15)0, set 150.0 INbH:!500 group is set as 00 sec DIsT Set range: 0.1 to 5.0 sec
Min. 37

7. OUT2(Red): M
45+0.6
0
gradient correction set value [INbH] as !500. [00 S], these are not M (selectable by 0.1 sec)
OUT2 output indicator of preset This value is also applied for minus input. When the measured 100.0 INbH:!000 displayed.
8. Unit sticker 45.2 input is -100.0V, it displays `5)0. lPEK Displays low peak ※ It is initialized by LOC Lock
Set range: OFF, LOC1, LOC2, LOC3
48.6 ②When the measured input is -100.0V in order to display -5)0, set 50.0 INbH: )500 M pressing any one
gradient correction set value [INbH] as )500. of keys. OFF Unlock LOC2 Lock PA 1, 2 groups
-100V
This value is also applied for plus input. When the measured input LOC1 Lock PA 1 group LOC3 Lock PA 0,1,2 groups
Connections and Insulated Block Diagram is 100.0V, it displays 5)0.
100V Input value

● M4NN-DV-1 ● M4NN-DA-1 INbH Note

-5)0
Parameter 1 Group ◎Parameter setting
1. Each parameter alternately displays parameter name and setting
① !500 ※Shaded part of Figure 1 is not displayed for the below cases. `0)0 RUN mode value in 0.5 sec.
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10 ●AC input model (Figure1) 2. Press M key to save setting value and it moves to next parameter.
●DC input model and minus input [MINU] is set as OFF. M 3 sec M 2 sec
② )500 `5)0 3. If any key is not touched for 60 sec in each parameter, it returns to
DC±1V
/±200mV
DC±10mA
/±2mA
●DC Current model and Input range [IN-R] is set as 4-20. RUN mode.
DC±10V/±2V SOURCE
DC±100mA
/±20mA HOLD SOURCE E.g. 2) Display scale setting [L-SC/H-SC] and gradient adjustment [INbH] (AC input) Display value PA1 4. Press M key for 3 sec, it is returned to RUN at any position.
HOLD
DC ±100V/±20V 5-24VDC /4-20mA 5-24VDC
①When the measured input AC 2.000V at the input range AC 0 to 5.000V and 12.500 5. Press , key to change the setting value at the parameter.
DC±1A/200mA ※1
( : moves set digit, : changes set value)
DC ±600V/±200V
DC ±5A/±2A it displays %000, set decimal point position [DOT] as )000 before setting the Display value IN-R Measured input type ※ : Press any key between , .
scale value. for measured M
● M4NN-AV-1 ● M4NN-AA-1
②When the measured input is AC 2.000V in order to display %000, 12.500 input ※1: Refer to Measurement Input.
should be displayed when max. input value is 5.000V. However, it cannot set MINU ON OFF Minus input display
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10 because the max. set value is 9.999. M (DC input only)
Set as gradient correction set value [INbH]×high scale value [H-SC]=12.500 5.000
AC 2V/1V AC100mA
/AC50mA as the following table. DISP SCAL
AC 20V/10V STND
SOURCE AC500mA SOURCE ③After this set is finished, it displays %000 when the measured input is 2.000V. AC Voltage/Current DC Voltage/Current
AC 110V/50V HOLD /AC250mA HOLD M M M
5-24VDC 5-24VDC
H-SC L-SC INbH Note Input Decimal point position
AC 600V/250V
AC 1A Display
AC 5A/2.5A
12.500 0.000 1.000 Unavailable to set because max. set value of H-SC is (999 value method DOT Set range: FREQ Frequency PF Power factor
● NPN open collector 6.250 0.000 2.000 2.000V 5.000V M 0, )0, )00, )000 M M
Decimal point position
3.125 0.000 4.000 In this case, any setting methods display the same High-limit
※Input and output are insulated from the power. display value. Set range: High-limit
11 12 13 14 H-SC scale value
※1
DOT H-RG input※1
2.500 0.000 5.000 0, )0, )00, )000
M M M
11 12 13 14 E.g. 3) Display scale setting [L-SC/H-SC] and gradient adjustment [INbH] (DC minus input) Display value Low-limit Mantissa of gradient Low-limit
OUT1 GO OUT2 COM Option output ①When the measured input DC -40mA at the input range DC -100.0 to 100.0mA and 400.0 L-SC scale value※1 INbH correction for L-RG input※1
it displays `6)0, set decimal point position [DOT] as )000 before setting the scale M frequency
M
● PNP open collector value. Set range of mantissa
ADC input circuit and Deviation correction of high limit :)100 to (999
②When the measured input is DC -40mA in order to display `6)0, -400.0 should INbH value (gradient correction)
11 12 13 14 indicator Power be displayed when min. input value is -100.0mA. However, it cannot set because
160.0 Set range: )100 to (999(multiply)
the min. set value is -199.9. Set as gradient correction set value [INbH]×low scale M
INbH Index of gradient
correction for frequency
1 2 3 4 5 6 7 8 9 10 value [L-SC] = -400.0 as the following table. Set high-limit scale value as (-(L-SC)) Input M Set range:
OUT1 GO OUT2 COM value. If high scale value is set at first, set low scale value as (-(H-SC)) value. value Deviation correction of low limit value
-100.0 -40.0 INbL (zero point) 10 0, 10 1, 10-2, 10-1
③After this setting is finished, it displays `6)0 when the measured input is 40.0 100.0 M Set range: -99 to 99
Monitoring Max./Min. Value [PA 0 group: hPEK/ lPEK, PA 2 group: PEkT] DC-40.0mA.
H-SC L-SC INbH Note
It monitors Max./Min. value of display value based on current display value and then display the data in hPEK
mode and lPEK mode of parameter 0 group. Set delay time(0 to 30 sec) in PEkT mode of parameter 2 group in 400.0 -400.0 1.000 Unavailable to set because max. set value of L-SC is `9(9
-160.0
Display value Factory Default ※1: Not displayed for indicator model.
200.0 -199.9 2.000 for measured
order to avoid caused by initial overcurrent or overvoltage, when monitoring the peak value. Delay time is 0 to 30 input Type Parameters M4NN-DV M4NN-DA M4NN-AV M4NN-AA Type Parameters M4NN-DV M4NN-DA M4NN-AV M4NN-AA
100.0 -100.0 4.000 In
sec and it starts to monitor the peak value after set time. this case, any setting methods display the same ※1
display value. -400.0 IN-R 600V 5A 600V 5A OU!H 600 %00 60)0 %000
When keys are pressed at hPEK and lPEK mode of parameter 0 group, it will be initialized. 80.0 -80.0 5.000 MINU ON ON - -
※
OU!L 1 -600 -%00 00)0 )000
※ hPEK, lPEK parameters are not displayed when monitoring delay time [PEkT] of parameter 2 group is set as PA0 ※
OU@H 1 600 %00 60)0 %000
DISP STND STND STND STND
as 0 sec [00 S].
Power Factor [PF] Display [PA1 group: H-RG/L-RG] DOT 0 0 0 0
(PA 0
group) OU@L
※1

※
-600 -%00 00)0 )000
hPEK 1
Minus Input Display Setting [PA1 group: MINU] ● This function displays LEAD and LAG by analog output signal from the power factor transducer. H-SC 600 500 600 5000 0 )00 )0 )000
PA1 ※
● It is available to accept several outputs of the power factor transducer by high-limit[H-RG]/low-limit[L-RG] (PA 1 L-SC -600 -500 0 0 lPEK 1 0 )00 )0 )000
●W hen minus input is unnecessary, or when display 0 not to display minus input due to display minus input
※1
analog output value setting in the power factor transducer. group) OU!T OFF OFF OFF OFF
INbH !000 !000 !000 !000
due to unstable input value around 0, set OFF this minus input display function. ● Power factor value is displayed as cos∅ value -0.50(LEAD) to 1.00 to 0.50 (LAG). OU@T
※1
OFF OFF OFF OFF
● When setting OFF, low-limit value of input range is set 0 and it displays minus input as 0. ● LEAD is when current phase leads voltage phase, LAG is when current phase lags behind voltage phase. INbL 00 00 00 00 ※
PA2 HYs1 1 - - - -
●T he low-limit value of L-SC, OU .L, L-RG parameters is changed based on "0". Min. display value is "0" and LEAD and LAG are invalid power. H-RG 600 500 - -
(PA ※
HYs2 1 - - - -
H-SC/ H-RG parameters display max. value of the input range. ● Set range: From min. to max. selected value from measurement input [IN-R]. L-RG -600 -500 - - 2 group)
The INbH/INbL/OU .T/HYs /OU .H parameters are initialized to factory default. PEkT 00 S 00 S 00 S 00 S
E.g.) W hen setting 200V in IN-R, H-RG and L-RG are available to set from `9(9 to 20)0. INbE - - 10 0 10 0
※In case of DC Current measurement input model, when measured input range [IN-R] is set as 4-20, this When setting 10V, H-RG and L-RG are available to set from `)00 to 1)00. (※H-RG > L-RG) DIsT )2 S )2 S )2 S )2 S
parameter is not displayed. Display <Factory default>
LOC OFF OFF OFF OFF
value
AC Frequency Measurement [PA1 group: DISP] COSΦ
1
LEAD LAG Model H-RG L-RG
Cautions during Use
M4NN-DV 600 -600 1. Follow instructions in 'Cautions during Use'. Otherwise, it may cause unexpected accidents.
It measures input signal frequency when it is an AC input. It uses fixed decimal point by DOT parameter setting
of parameter 1 group, measured range can be changed by setting and measured range of decimal point position M4NN-DA %00 -%00 2. 5-24VDC power supply should be insulated and limited voltage/current or Class 2, SELV power supply device.
is as below chart. It is available to adjust upper gradient at INbH and INbE of parameter 1 group. In order to 0.5 3. Install a power switch or circuit breaker in the easily accessible place for supplying or disconnecting the power.
※Power factor display is only for DC measurement
measure frequency normally, input signal, over 10% F.S. of the measured range, should be supplied. Please 4. Keep away from high voltage lines or power
input model. Connection with the line filter Connection with the varistor
select the proper point of measurement terminal. lines to prevent inductive noise.
Display value In case installing power line and input signal line Install the line filter close
●M  easured range L-RG (H-RG)+(L-RG) H-RG Input value 0.50 to the panel meter
closely, use line filter or varistor at power line HI
Decimal point position 2 HI
)000 )00 )0 0 and shielded wire at input signal line. 110/
110/
0.75 Panel meter
Measurement range 0.100 to 9.999Hz 0.10 to 99.99Hz 0.1 to 999.9Hz 1 to 9999Hz E.g.1) When the output of the power factor transducer is DC 4-20mA, Do not use near the equipment which generates 220VAC Panel meter 220VAC
strong magnetic force or high frequency noise. LOW
※ Accuracy of frequency measurement: Below 1kHz, F.S. ±0.1rdg ±2digit. From 1 to 10kHz, F.S. ±0.3rdg ±2digit. ①Connect the output to the input terminal 5(+), 7(-) of this unit, then LOW
set input range [IN-R] as 4-20. 0.90
5. This unit may be used in the following
● INbH: 0.100 to 9.999 (gradient adjustment of high-limit value) environments. Earth ground
-2 -1 0 1 ②When setting the input range as 4-20, L-RG is set 1.00
● INbE: 10 , 10 , 10 , 10 (index adjustment of INbH) ①Indoors
as $00 and H-RG is set as 2)00 automatically. L-RG and H-RG -0.90
is for the setting of the power factor transducer output. (in the environment condition rated in 'Specifications')
②Altitude max. 2,000m
Error Display ③If measured input is 4mA, it displays -)50. For 12mA measured -0.75
input, it displays !00 and for 20mA,
③Pollution degree 2
④Installation category II
Display Description Display Description it displays )50.
Flashes when measured input is exceeded
HHHH the max. allowable input(+110%)
Flashes when input frequency is exceeded E.g.2) When the output of the power factor transducer is DC1-5V, -0.50
①Connect the output to the input terminal 5(+), 7(-) of this unit, Min. set
Major Products
F-HH the max. measured range(10kHz) and value 1V 3V 5V Photoelectric Sensors Temperature Controllers
display range (9999) then set the input range [IN-R] as 10V. 1 Fiber Optic Sensors Temperature/Humidity Transducers
Flashes when measured input is exceeded ②Select minus input display function [MINU] as OFF not to 0.9
Door Sensors SSRs/Power Controllers
LLLL the min. allowable input Flashes when power factor display value to display minus value. Door Side Sensors Counters
(minus input ON : -110%, OFF : -10%) PF-H measured input is over than LAG 0.50
③Set H-RG as %00 and L-RG as !00 for the output of the power 0.5 Area Sensors Timers
Flashes when display input is exceeded max. factor transducer. Proximity Sensors Panel Meters
D-HH Flashes when power factor display value to Pressure Sensors Tachometer/Pulse (Rate) Meters
display range (9999) PF-L measured input is less than LEAD -0.50 ④If measured input is 1V, it displays -)50. For 3V measured LEAD LAG
Input value Rotary Encoders Display Units http://www.autonics.com
input, it displays 1.00 and for 5V, Output mode HL Connector/Sockets Sensor Controllers
Flashes when display input is exceeded min. LAG
D-LL display range (-1999)
it displays )50.
OU!H value 0.90
Switching Mode Power Supplies HEADQUARTERS:
E.g.3) When LEAD value is smaller than -0.90, Control Switches/Lamps/Buzzers 18, Bansong-ro 513beon-gil, Haeundae-gu, Busan,
1.00
※Error is cleared when the input value is within measurement range or display range. LAG value is smaller than 0.90, and OUT1 is used, OU!L value -0.90 Hysteresis I/O Terminal Blocks & Cables South Korea, 48002
Stepper Motors/Drivers/Motion Controllers TEL: 82-51-519-3232
※The above specifications are subject to change and some models may be discontinued without notice. ①Set OU!T as HL at parameter 2 group. LEAD Hysteresis
Graphic/Logic Panels E-mail: sales@autonics.com
※Be sure to follow cautions written in the instruction manual and the technical descriptions (catalog, ②Set OU!H as )90 and OU!L as -)90 Field Network Devices
at parameter 0 group. Laser Marking System (Fiber, Co₂, Nd: YAG) DRW170794AA
homepage). ※ OU@T is also same setting as OU!T. Output value Laser Welding/Cutting System