MCQ For EG

1. Which type of line is a part of Dimensioning System?
a) Cutting Plane Lines

b) Extension Lines
c) Break Lines
d) Hidden Lines
2. The position of cutting plane is shown by ________.

a) Long and thin chain lines
b) Short dashes of approximately equal lengths
c) Long chain line, thick at ends only
d) Alternately long and short dashes
3. As far as possible dimensions should be given in one unit, preferably in ________.

a) Millimetres
b) Centimetres
c) Decimetres
d) Inches
4. The line connecting a view to a note is called a ________.

a) Hidden Lines
b) Extension Lines
c) Section Lines
d) Leader Dimension Lines
5. When the drawing is drawn of the same size as that of the object, the scale used is,
____
a) Reduced Scale
b) Enlarged Scale
c) Full Size scale
d) Diagonal Scale
6. The value of Representative Fraction for drawing of the buildings should be ________
a) > 1
b) < 1
c) = 1
d) None of the above
7. The distance between point A and point B is 330 m and shown by a 16.5 cm long line
calculate the R.F.
(a.) 1/1000
(b.) 1/200
(c.) 1/100
(d.) 1/2000
8. The R.F. value is 1:10 showing 3 Consecutive units and long enough to read the
Distance of 5 feet. What will be the length of scale?
(a.) 6 inches
(b.) 1 foot
(c.) 5 feet
(d.) 12 inches
9. The sum of the distances of any point on the ellipse from its two foci is always the
same and equal to the ______.
(a.) Major axis
(b.) Minor axis
(c.) None of the above
(d.) Any one of the above and depends on the situation.
10. For Hyperbola the distance between focus and vertex is always ________ the distance
between vertex and directrix.
(a.) Smaller than
(b.) larger than
(c.) Equal to
(d.) None of the above
11. The curve generated by the point outside the circumference of the rolling circle, while
rolling inside another circle _______.
(a.) Cycloid
(b.) Superior Trochoid
(c.) Superior Hypotrochoid
(d.) Superior Epitrochoid
12. A curve traced out by a point on the straight line which rolls round the circle or
polygon without slipping is called ________.
(a.) Cycloid
(b.) Trochoid
(c.) Spiral
(d.) Involute.
13. Which curve is used to decide the cam profile for automation?
(a.) Involute
(b.) Spiral
(c.) Cycloid
(d.) Conics
14. Which one among the below is not used to decide the gear tooth profile?
(a.) Cycloid
(b.) Spiral
(c.) Conics
(d.) Involute
15. The largest and smallest radius for Archemedian Spiral of one convolution is 22 mm
and 130 mm respectively. What will be the value of constant of the curve?
(a.) 34.38
(b.) 108
(c.) 0.3
(d.) 17.18
16. The point at which the conics cuts its axis is called _______.
(a.) Vertex
(b.) Focus
(c.) Directrix
(d.) All of the above
17. The point is kept on the HP, its Front view will be
(a.) Above xy line
(b.) Below xy line
(c.) On the xy line
18. If the Point is situated behind VP, its top view will be
(a.) On the xy line
(b.) Above the xy line
(c.) Below the xy line
19. State the quadrant for the point P if its top view is 40 mm above xy and the front view
is 20 mm below the top view.
(a.) Second
(b.) First
(c.) Fourth
(d.) Third
20. In projection of a point, the side view of a point A is denoted as,
(a.) A
(b.) a
(c.) a’
(d.) a’’
21. A line may not be _________.

(a.) Perpendicular to both the planes.
(b.) Parallel to both the planes.
(c.) Parallel to one plane and inclined to the other plane.
(d.) Parallel to one plane and perpendicular to the other plane.
22. If the apparent and the true inclinations of a line with Vertical Plane (VP) are equal,
the line is _________.
(a.) Inclined to both the planes.
(b.) Parallel to horizontal plane.
(c.) Parallel to profile planes.
(d.) Parallel to vertical plane.
23. An 80 mm long line AB, inclined at 450 to HP and 300 to VP has end A 20 mm
above HP and 30 mm in front of VP, the end B will lie in?
(a.) Second or Fourth Quadrant
(b.) Third Quadrant
(c.) First Quadrant
(d.) Any of these
24. A line PQ 75 mm long is inclined to the Horizontal plane at an angle of 600, and 10
mm above HP and 15 mm in front of VP, the apparent inclination with the HP will
be_______.
(a.) < 600
(b.) > 600
(c.) = 600
(d.) Any of these
25. The distance between the end projectors of the line is,
(a.) The distance between true length of the line and elevation length.
(b.) The distance between the projectors passing through front view and elevation
points.
(c.) The distance between the projectors passing through top view and plan points.
(d.) The distance between the projectors passing through elevation points and
plan points.
26. The projection in which projectors are parallel to each other and perpendicular to
plane of projection is called,
(a.) Oblique projection
(b.) Perspective projection
(c.) Orthographic projection
(d.) Isometric projection
27. In orthographic projection arrow X indicate direction to get ______ view of the
object.
(a.) Top
(b.) Front
(c.) Left hand side view
(d.) Right hand side view
28. For the third angle projection system which one among the following is incorrect?
(a.) LHSV is on left side of the FV.
(b.) The plane of projection is assumed to be transparent.
(c.) Object is placed in third quadrant.
(d.) Object will be between the observer and the plane of projection.

MCQ For EG

Uploaded by

Copyright:

Available Formats

MCQ For EG

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

MCQ For EG

Uploaded by

Copyright:

Available Formats

1. Which type of line is a part of Dimensioning System?

a) Cutting Plane Lines

2. The position of cutting plane is shown by ________.

3. As far as possible dimensions should be given in one unit, preferably in ________.

4. The line connecting a view to a note is called a ________.

21. A line may not be _________.

You might also like