Yamaha CD-S300 Service Manual

COMPACT DISC PLAYER
CD-S300 SERVICE MANUAL
IMPORTANT NOTICE
This manual has been provided for the use of authorized YAMAHA Retailers and their service personnel.
It has been assumed that basic service procedures inherent to the industry, and more specifically YAMAHA Products, are already known
and understood by the users, and have therefore not been restated.
WARNING: Failure to follow appropriate service and safety procedures when servicing this product may result in personal injury,
destruction of expensive components, and failure of the product to perform as specified. For these reasons, we advise
all YAMAHA product owners that any service required should be performed by an authorized YAMAHA Retailer or
the appointed service representative.
IMPORTANT: The presentation or sale of this manual to any individual or firm does not constitute authorization, certification or
CD-S300
recognition of any applicable technical capabilities, or establish a principle-agent relationship of any form.
The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering, and service
departments of YAMAHA are continually striving to improve YAMAHA products. Modifications are, therefore, inevitable and
specifications are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, please contact the
distributor's Service Division.
WARNING: Static discharges can destroy expensive components. Discharge any static electricity your body may have
accumulated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss).
IMPORTANT: Turn the unit OFF during disassembly and part replacement. Recheck all work before you apply power to the unit.
■ CONTENTS
TO SERVICE PERSONNEL ........................................2–3 UPDATING FIRMWARE /
PREVENTION OF ELECTROSTATIC DISCHARGE ......4 ファームウェアの書き込み ..................................... 16–21
FRONT PANEL ...............................................................5 DISPLAY DATA .............................................................22
REAR PANELS ...........................................................5–6 IC DATA ...................................................................23–30
REMOTE CONTROL PANEL ..........................................7 PIN CONNECTION DIAGRAMS .............................31–32
SPECIFICATIONS / 参考仕様 .........................................8 BLOCK DIAGRAM ........................................................33
INTERNAL VIEW ............................................................9 PRINTED CIRCUIT BOARDS .................................34–40
DISASSEMBLY PROCEDURES / 分解手順 ........... 10–12 SCHEMATIC DIAGRAMS .......................................41–45
TEST MODE / テストモード ................................... 13–14 REPLACEMENT PARTS LIST ................................47–55
FACTORY MODE / ファクトリーモード ....................... 15 REMOTE CONTROL .....................................................56
Copyright © 2009 All rights reserved.

1011 4 6 This manual is copyrighted by YAMAHA and may not be copied or
redistributed either in print or electronically without permission.
P.O.Box 1, Hamamatsu, Japan
Downloaded from www.dlmanuals.com '09.09
CD-S300
■ TO SERVICE PERSONNEL
AC LEAKAGE
1. Critical Components Information WALL EQUIPMENT TESTER OR
Components having special characteristics are marked and OUTLET UNDER TEST EQUIVALENT
must be replaced with parts having specifications equal to those
originally installed.
2. Leakage Current Measurement (For 120V Models Only)
When service has been completed, it is imperative to verify
that all exposed conductive surfaces are properly insulated INSULATING
TABLE
from supply circuits.
• Meter impedance should be equivalent to 1500 ohms shunted • Leakage current must not exceed 0.5mA.
by 0.15 μF. • Be sure to test for leakage with the AC plug in both polarities.
“CAUTION”
“F801: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE 500mA,
250V FUSE.”
CAUTION
F801: REPLACE WITH SAME TYPE 500mA, 250V FUSE.
ATTENTION
F801: UTILISER UN FUSIBLE DE RECHANGE DE MÉME TYPE DE 500mA, 250V.
WARNING: CHEMICAL CONTENT NOTICE!

This product contains chemicals known to the State of California to cause cancer, or birth defects or other reproductive
harm.
DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REASON
WHATSOEVER!
Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or
expose eyes to solder/flux vapor!
If you come in contact with solder or components located inside the enclosure of this product, wash your hands before
handling food.
CD-S300
About lead free solder / 無鉛ハンダについて

All of the P.C.B.s installed in this unit and solder joints are 本機に搭載されているすべての基板およびハンダ付けに
soldered using the lead free solder. よる接合部は無鉛ハンダでハンダ付けされています。
Among some types of lead free solder currently available, 無鉛ハンダにはいくつかの種類がありますが、修理時に
it is recommended to use one of the following types for は下記のような無鉛ハンダの使用を推奨します。
the repair work. Sn+Ag+Cu（錫 + 銀 + 銅）
• Sn + Ag + Cu (tin + silver + copper) Sn+Cu（錫 + 銅）
• Sn + Cu (tin + copper) Sn+Zn+Bi（錫 + 亜鉛 + ビスマス）
• Sn + Zn + Bi (tin + zinc + bismuth)
注意：
Caution: 無鉛ハンダの融点温度は通常の鉛入りハンダに比べ 30 ∼
As the melting point temperature of the lead free solder 40℃程度高くなっていますので、それぞれのハンダに合っ
is about 30°C to 40°C (50°F to 70°F) higher than that of たハンダごてをご使用ください。
the lead solder, be sure to use a soldering iron suitable
to each solder.
WARNING: Laser Safety

This product contains a laser beam component. This component may emit invisible, as well as visible radiation,
which may cause eye damage. To protect your eyes and skin from laser radiation, the following precautions must
be used during servicing of the unit.
1) When testing and/or repairing any component within the product, keep your eyes and skin more than 30 cm/1 feet
away from the laser pick-up unit at all times. Do not stare at the laser beam at any time.
2) Do not attempt to readjust, disassemble or repair the laser pick-up, unless noted elsewhere in this manual.
3) CAUTION: Use of controls, adjustments or performance of procedures other than those specified herein may result in
hazardous radiation exposure.
2
Downloaded from www.dlmanuals.com
CD-S300
Laser Emitting conditions:

1) When the Top Cover is removed, and the STANDBY/ON SW is turned to the “ON” position, the laser component will
emit a beam for several seconds to detect if a disc is present. During this time (5-10 sec.) the laser may radiate
through the lens of the laser pick-up unit. Do not attempt any servicing during this period!
If no disc is detected, the laser will stop emitting the beam. When a disc is loaded, you will not be exposed to any
laser emissions.
2) The laser power level can be adjusted with the VR on the pick-up PWB, however, this level has been set by the factory
prior to shipping from the factory. Do not adjust this laser level control unless instruction is provided elsewhere in this
manual. Adjustment of this control can increase the laser emission level from the device.
Laser Diode Properties

Type: GaAlAs
Wavelength: 790 nm
Laser output: max. 1.23 μW *
* This output is the value measured at a distance of about 200 mm from the objective lens surface
on the Optical Pick-up Block.
CD-S300
R, A, G, L, J models T model
Warning for power supply

The primary side of the power supply carries live mains voltage when the player is connected to the mains even
when the player is switched off !
This primary area is not shielded so it is possible to accidentally touch copper tracks and/or components when servicing
the player.
Service personnel have to take precautions to prevent touching this area or components in this area.
Note:
The screws on the DVD mechanism may never be touched, removed or re-adjusted.
Handle the DVD mechanism with care when the unit has to be exchanged!
The DVD mechanism is very sensitive for dropping or giving shocks.
3
CD-S300
■ PREVENTION OF ELECTROSTATIC DISCHARGE

Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are
called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect
transistors and semiconductor “chip” components. The following techniques should be used to help reduce the incidence
of component damage caused by electrostatic discharge (ESD).
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD
on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging
ESD wrist strap, which should be removed for potential shock reasons prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as
aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4. Use only an anti-static solder removal device. Some solder removal devices not classified as “anti-static (ESD
protected)” can generate electrical charge sufficient to damage ES devices.
5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it.
(Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil
or comparable conductive material).
7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective
material to the chassis or circuit assembly into which the device will be installed.
CAUTION: Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as
brushing together of your fabric clothes or lifting of your foot from a carpeted floor can generate static electricity (ESD)
sufficient to damage an ES device).
Grounding for electrostatic breakdown prevention

1. Human body grounding.
Use the antistatic wrist strap to discharge the static electricity from your body.
2. Work table grounding.
Put a conductive material (sheet) or steel sheet on the area where the optical pickup is placed and ground the sheet.
CD-S300
Caution:
The static electricity of your clothes will not be grounded through the wrist strap. So take care not to let your clothes touch
the optical pickup.
Anti-static wrist strap

1M-ohms
Conductive material
(sheet) or steel sheet
4
CD-S300
■ FRONT PANEL
R, T, A, G, L, J models
■ REAR PANELS
R model
CD-S300
T model
A model
5
CD-S300
G model
L model
J model
CD-S300
6
CD-S300
■ REMOTE CONTROL PANEL

CDX8
CD-S300
7
CD-S300
■ SPECIFICATIONS / 参考仕様
■ Audio Section / オーディオ部
Output Level / 出力レベル (1 kHz, 0 dB)

..........................................................................................2.0 ±0.3 V “iPod” is a trademark of Apple Inc., registered in U.S. and other countries.
“Made for iPod” means that an electronic accessory has been designed
Signal to Noise Ratio / 信号対雑音比
to connect specifically to iPod and has been certified by the developer to
................................................................................. 105 dB or more meet Apple performance standards.
Apple is not responsible for the operation of this device or its compliance
Dynamic Range / ダイナミックレンジ with safety and regulatory standards.
................................................................................... 96 dB or more iPod は、米国およびその他の国々で登録された Apple Computer, Inc. の商
Total Harmonic Distortion / 歪率 (1 kHz) 標または登録商標です。
｢Made for iPod」とは、iPod 専用に接続するよう設計され、アップルが定
..................................................................................0.003 % or less
める性能基準を満たしているとデベロッパーによって認定された電子アク
Frequency Response / 周波数特性 (2 Hz to 20 kHz) セサリーであることを示します。
............................................................................................. ±0.5 dB アップルは、これらの機器操作または、安全規制基準に関する一切の責任
を負いません。
Digital Output Terminal / デジタル出力端子
......................................................................................... Optical x 1
Coaxial x 1
Other Output Terminal / その他の出力端子

...................................................................................Analog out L/R
USB • DIMENSIONS / 寸法図
■ General / 総合
Power Consumption / 消費電力
260 (10-1/4")
210 (8-1/4")
.................................................................................................. 13 W
Power Supply / 電源電圧

R, L models ........................... AC 110/120/220/230–240 V, 50/60 Hz
T model ................................................................... AC 220 V, 50 Hz
A model .................................................................. AC 240 V, 50 Hz
G model .................................................................. AC 230 V, 50 Hz
CD-S300
J model .............................................................. AC 100 V, 50/60 Hz
(2-3/4")
Dimensions (W x H x D) / 寸法（幅×高さ×奥行き）
70
................................. 435 x 86 x 260 mm (17-1/8" x 3-3/8" x 10-1/4")
(3-3/8")
Weight / 質量
86
................................................................................. 3.5 kg (7.7 lbs.)
395 (15-1/2") 16
(5/8")
Finish / 仕上げ
435 (17-1/8")
Black color .....................................................R, T, A, G, L, J models
Silver color ......................................................R, T, A, G, L, J models
Accessories / 付属品 Unit: mm (inch)

Remote control (CDX8) .................................................................x 1 単位：mm（インチ）
Battery (R6, AA, UM-3) .................................................................x 2

Audio pin cable (1.0 m) ................................................................x 1
Power cable (1.5 m) .....................................................................x 1
* Specifications are subject to change without notice due to

product improvements.
※ 参考仕様および外観は予告なく変更されることがあります。
R ....................General model G .................European model

T..................... Chinese model L .................Singapore model
A ................Australian model J ................... Japanese model
8
CD-S300
■ INTERNAL VIEW
1 2 3 4 5 1 OPERATION (7) P.C.B. (R, L models)

2 OPERATION (5) P.C.B.
4 MAIN P.C.B.
8 Loader mechanism ass'y
6 7 8 9
10 11 12
CD-S300
9
CD-S300
■ DISASSEMBLY PROCEDURES / 分解手順

(Remove parts in the order as numbered.) （番号順に部品を取り外してください。）
Disconnect the power cable from the AC outlet. AC 電源コンセントから、電源コードを抜いてください。
1. Removal of Top Cover 1. トップカバーの外し方

a. Remove 4 screws (①) and 2 screws (②). (Fig. 1) a. ① のネジ 4 本、② のネジ 2 本を外します。（Fig. 1）
b. Remove the top cover. (Fig. 1) b. トップカバーを取り外します。（Fig. 1）
Top cover
トップカバー
OPERATION (6) P.C.B. 2
Front panel ass'y

Hook フロントパネルASSY
フック
CB803
3
MAIN P.C.B.
4
CD-S300
Lid CB304
リッド
CB6
5 Hook CB807
3 フック OPERATION (8) P.C.B.
Lid
How to manually eject the disc tray /
リッド Disc tray
ディスクトレイを開ける方法
ディスクトレイ
Flatblade screwdriver
マイナスドライバー
Fig. 1
2. Removal of Front Panel Ass’y 2. フロントパネル ASSY の外し方

a. Using a flatblade screwdriver, move the slider at the a. マイナスドライバーで底面のスライダーを上図の矢印
bottom in the direction of the arrow shown above. の方向に動かします。（Fig. 1）
(Fig. 1) ディスクトレイを開けてリッドを取り外し、ディスク
Open the disc tray, remove the lid and close the disc トレイを閉じます。（Fig. 1）
tray. (Fig. 1) b. ③ のネジ 2 本を外します。（Fig. 1）
b. Remove 2 screws (③). (Fig. 1)
10
CD-S300
c. Remove 4 screws (④) and 2 screws (⑤). (Fig. 2) c. ④ のネジ 4 本、⑤ のネジ 1 本を外します。（Fig. 2）
d. Remove CB6, CB304, CB803 and CB807. (Fig. 1) d. CB6、CB304、CB803、CB807 を外します。（Fig. 1）
e. Release 2 hooks and then remove the front panel e. フック 2 箇所を外し、フロントパネル ASSY を取り外
ass’y. (Fig. 1) します。（Fig. 1）
Bottom view
4 5 4 5 4
Fig. 2
3. Removal of Loader Mechanism Unit 3. ローダーメカユニットの外し方

a. Remove 4 screws (⑥). (Fig. 3) a. ⑥ のネジ 4 本を外します。（Fig. 3）
b. Remove CB2 and CB3. (Fig. 3) b. CB2、CB3 を外します。（Fig. 3）
c. Remove CB4 and ground the terminal side of the c. CB4 を外し、カード電線の端子面をクリップ等でアー
flexible flat cable with a clip or the like. (Fig. 3) スします。（Fig. 3）
CD-S300
d. Remove the loader mechanism unit. (Fig. 3) d. ローダーメカユニットを取り外します。（Fig. 3）
6 Loader mechanism unit 17 mm

ローダーメカユニット (0.67")
6
Terminal side
端子面
Clip
クリップ
CB3 Use a clip or other item to

ground the unit.
CB2
クリップ等でアースしてください。
MAIN P.C.B.
CB4
Fig. 3 11
CD-S300
When checking the P.C.B.s: P.C.B. をチェックする場合には：

• Spread the rubber sheet and the cloth. Then place ・ゴムシートと布を敷き、その上に本機を置いてチェッ
this unit on the cloth and check it. (Fig. 4) クします。（Fig. 4）
• Connect the ground point (ST701) of the front panel ・フロントパネル ASSY のアース（ST701）をアース線等
ass’y to the chassis with a ground lead or the like. でシャーシに接続してください。（Fig. 4）
(Fig. 4) ・外したケーブル（コネクター）をすべて接続します。
• Reconnect all cables (connectors) that have been ・フラットケーブルを接続する際、極性に注意してく
disconnected. ださい。
• When connecting the flexible flat cable, be careful
with polarity.
CD-S300
Rubber sheet and cloth

ゴムシートと布
Ground lead
アース線
Ground lead
アース線
ST701 Chassis
シャーシ
Front panel ass'y
フロントパネルASSY
Fig. 4
12
CD-S300
■ TEST MODE / テストモード

● Starting test mode ● テストモードの起動
When starting the test mode, check the FL display テストモードの起動時に、FL ディスプレイとインジケー
and indicators for display/indication condition. ターの表示状態をチェックします。
1. While pressing the “CD/USB”, “ ” (Skip/ 1. 本機の下図に示す CD/USB キー、（頭
Search forward) and “ ” (Pause) keys of this unit 出し／早送り）キー、（ポーズ）キーを押しなが
as shown in the figure below, press the “ ” (Power) ら（電源）スイッチを押して電源を入れ、3 つの
switch to turn on the power and keep pressing キーを押し続けます。
those 3 keys.
iPod/USB indicator FL display

iPod/USB インジケーター FL ディスプレイ
Power indicator PURE DIRECT indicator

電源インジケーター PURE DIRECT インジケーター
" " (Power) switch

（電源）スイッチ While pressing these keys, press the “ ” (Power) switch to turn on the power.
これらのキーを押しながら、（電源）スイッチを押して電源を入れます。
FL display / FL ディスプレイ表示
CD-S300
All segments ON
全セグメント点灯
Release the keys

キーを離す
All segments OFF

全セグメント消灯
2. While keep pressing those 3 keys, check that all 2. 3 つのキーを押したまま、全てのインジケーター

indicators (Power, iPod/USB, PURE DIRECT) are （電源、iPod/USB、PURE DIRECT）が点灯してい
lit. ることを確認します。
At the same time, check that all segments of the 同時に、FL ディスプレイの全セグメントが点灯し
FL display are lit. ていることを確認します。
3. Release those 3 keys. 3. 3 つのキーを離します。
Then check that all indicators (Power, iPod/USB, 全てのインジケーター（電源、iPod/USB、PURE
PURE DIRECT) as well as all segments of the FL DIRECT）と、FL ディスプレイの全セグメントが
display are turned off. 消灯していることを確認します。
4. The Test Mode is activated. 4. テストモードが起動します。
13
CD-S300
● Operation Procedure of Test Mode ● テストモード時の操作
Function list of remote control keys / リモコンキーの機能一覧
Key code /
Key / キー Function / 機能
キーコード
OPEN/CLOSE 79-01 Disc tray open/close / ディスクトレイオープン／クローズ
1 79-11 Laser on / レーザーオン
2 79-12 Laser off / レーザーオフ
3 79-13 Focus operation / フォーカス動作
Traverse in * Press the “5” key to stop traverse.

4 79-14
トラバースイン ※ 5 キーを押してトラバースを停止してください。
5 79-15 Traverse stop / トラバースストップ
Traverse out * Press the “5” key to stop traverse.

6 79-16
トラバースアウト ※ 5 キーを押してトラバースを停止してください。
Spindle reverse * Press the “8” key to stop spindle.

7 79-17
スピンドルリバース ※ 8 キーを押してスピンドルを停止してください。
8 79-18 Spindle off / スピンドルオフ
* Press the “8” key to stop spindle.

9 79-19 Spindle on / スピンドルオン
※ 8 キーを押してスピンドルを停止してください。
CD-S300
● Canceling Test Mode ● テストモードの解除

Press the “ ” (Power) switch of this unit to turn off the 本機の（電源）スイッチを押して電源を切ります。
power.
14
CD-S300
■ FACTORY MODE
● Starting Factory Mode ● ファクトリーモードの起動
While pressing the “ ” (Play) and the “ ” (Stop) 本機の下図に示す（再生）キーと（停止）キー
keys of this unit as shown in the figure below, press を押しながら（電源）スイッチを押して電源を入
the “ ” (Power) switch to turn on the power. れます。
The Factory Mode is activated. ファクトリーモードが起動します。
FL display
FL ディスプレイ
" " (Power) switch While pressing these keys, press the “ ” (Power) switch to turn on the power.
" （電源）
" スイッチこれらのキーを押しながら、（電源）スイッチを押して電源を入れます。
Display provided when factory mode started / ファクトリーモード起動時の表示
FACTORY LOADING NO DISC
● Operation Procedure of Factory Mode ● ファクトリーモード時の操作
CD-S300
Function list of remote control keys / リモコンキーの機能一覧
Key Key code Function

キーキーコード機能
Firmware version of the microprocessor
* Press the “CD/USB” key to select the CD mode
(IC305 of the MAIN P.C.B.) is displayed.
マイコン（MAIN P.C.B.のIC305）のファーム ※ CD/USB キーを押して、CDモードを選択し
ウェアバージョンが表示されます。てください。
DISPLAY 79-0A
Firmware version of the USB IC
* Press the “CD/USB” key to select the USB mode
(IC7 of the MAIN P.C.B.) is displayed.
USB IC（MAIN P.C.B.のIC7）のファームウェア ※ CD/USB キーを押して、USBモードを選択し
バージョンが表示されます。てください。
EEPROM (IC304 of the MAIN P.C.B.) is initialized.
CLEAR 79-0D
EEPROM（MAIN P.C.B.のIC304）を初期化します。
● Canceling Factory Mode ● ファクトリーモードの起動

Press the “ ” (Power) switch of this unit to turn off the 本機の（電源）スイッチを押して電源を切ります。
power.
15
CD-S300
■ UPDATING FIRMWARE / ファームウェアの書き込み

After replacing the following parts with the replacement 下記の部品をサービス部品に交換した場合、下記の手順
parts, update the latest firmware according to the により最新のファームウェアの書き込みを行ってくださ
following procedure. い。
MAIN P.C.B. MAIN P.C.B.
Microprocessor (IC305) of MAIN P.C.B. Microprocessor（IC305）of MAIN P.C.B.
● Required tools ● 必要なツール

• Firmware downloader program ・ファームウェア書き込み用プログラム
....................................................... FlashSta.exe ............................................................................... FlashSta.exe
• Firmware ・ファームウェア
................................................... C5S3_xxxx.mot .........................................................................C5S3_xxxx.mot
C5S3_xxxx.id C5S3_xxxx.id
• RS232C cross cable “D-sub 9 pin female” ・ RS232C クロスケーブル D-sub 9pin メス
(Specifications) （仕様）
Pin No.2 RxD Pin No.2 RxD Pin No.2 RxD Pin No.2 RxD
Pin No.3 TxD Pin No.3 TxD Pin No.3 TxD Pin No.3 TxD
Pin No.5 GND Pin No.5 GND Pin No.5 GND Pin No.5 GND
Pin No.7 RTS Pin No.7 RTS Pin No.7 RTS Pin No.7 RTS
Pin No.8 CTS Pin No.8 CTS Pin No.8 CTS Pin No.8 CTS
• RS232C conversion adaptor (Part No.: WR492800) ・ RS232C 変換アダプター（部品番号：WR492800）
● Preparation and precautions ● 準備と注意

• Download the firmware downloader program and ・指定のダウンロード先から、ファームウェア書き
the latest firmware from the specified source to 込み用プログラムと最新のファームウェアを、PC
CD-S300
the same folder of the PC. の同じフォルダにダウンロードしてください。

• Prepare the above specified RS232C cross cable. ・ RS232C クロスケーブルは必ず上記仕様のものを
• While writing the firmware, keep the other application 用意してください。
software on the PC closed. ・書き込み時は、PC 上の他のアプリケーションソ
It is also recommended to keep the software on フトは閉じてください。
the task tray closed as well. さらに、タスクトレイ上にあるソフトも閉じてお
くことを推奨します。
● Confirmation of firmware version ● ファームウェアバージョンの確認

Before and after updating the firmware, check the ファームウエアの書き込みの前後に、ファームウエ
firmware version by using the factory mode menu. アのバージョンをファクトリーモードで確認します。
Start up the factory mode of this unit, and press the 本機のファクトリーモードを起動し、リモコンの
“DISPLAY” key of the remote control. The firmware DISPLAY キーを押すとファームウェアバージョンが
version is displayed. (See “FACTORY MODE”) 表示されます。（「ファクトリーモード」参照）
Note down the displayed firmware version. 表示されたファームウェアバージョンを書き留めま
す。
OPE: v1.09 Firmware version
16
CD-S300
● Connection ● 接続
1. Set the switch (SW7) of RS232C conversion 1. RS232C 変換アダプターのスイッチ（SW7） FLASH
adaptor to the “FLASH UCOM” position. (Fig. 1) UCOM 側に設定します。（Fig. 1）
2. Connect the writing port (CB902 of OPERATION 2. 本機の書き込み用ポート（OPERATION P.C.B. の
P.C.B.) located on the rear panel of this unit to the CB902）と PC のシリアルポート（RS232C）を下記
serial port (RS232C) of the PC with RS232C cross のように接続します。（Fig. 1）
cable, RS232C conversion adaptor and flexible
flat cable as shown below. (Fig. 1)
This unit
PC
Serial port (RS232C)
RS232C conversion adaptor

RS232C変換アダプター
RS232C cross cable

RS232C クロスケーブル FLASH
OTHER Flexible flat cable (9P)
UCOM
カード電線（9P）
SW7
CD-S300
Fig. 1
17
CD-S300
● Operation procedures ● 操作方法

1. Connect the power cable of this unit to the AC 1. 本機の電源コードを AC コンセントに接続します。
outlet. 2. 本機の（電源）スイッチを押して電源を入れ
2. Press the “ ” (Power) switch of this unit to turn on ます。
the power. 3. FlashSta.exe を起動します。（Fig. 2）
3. Start up FlashSta.exe. (Fig. 2) 下記の画面が表示されます。（Fig. 2）
The screen appears as shown below. (Fig. 2) 4. 送信データ、ポートを選択します。（Fig. 2）
4. Select the data to be transmitted and port. (Fig. 2) ・ Select Program
• Select Program Internal ﬂash memory を選択します。
Select Internal flash memory. ・ RS232C
• RS232C 接続している RS-232 Ｃポートを選択します。
Select the port of RS-232C ※ ポートの選択は COM1 ∼ 4 までが使用で
* For selection of the port, COM1 to 4 can きます。
be used. COM5 以上は使用できませんので、PC 側
As COM5 or higher port cannot be used, の設定で COM1 ∼ 4 を選択してください。
select out of COM 1 to 4 of the setting on
the PC side.
Select Internal flash memory

Internal ﬂash memory を選択します
Select the port of RS-232C

接続している RS-232C ポートを選択します
CD-S300
Fig. 2
5. Click [Refer...] and select the firmware name. 5. ［Refer...］をクリックし、書き込むファームウェア

(Fig. 3) を選択します。（Fig. 3）
* The ID and MCU Type are loaded automatically ※ ID、および MCU Type は書き込みファイル選
when the file is selected. (Fig. 3) 択後、自動的に取り込まれます。（Fig. 3）
Click [OK]. (Fig. 3) ［OK］をクリックします
When [Refer...] is clicked, the “Open” screen appears.

［Refer...］をクリックすると「ファイルを開く」が表示されます
18
Fig. 3
CD-S300
6. Click [Setting], and set the baud rate. (Fig. 4) 6. ［Setting］をクリックし、通信速度の設定を行い

ます。（Fig. 4）
Select 115200 bps for the baud rate and 40 ms for

the program intervals.
* Reduce the baud rate if a transmission error
occurs frequently.
通信速度は 115200bps、時間幅は 40ms を選択し
ます。
※ 送信エラーが多発する場合は、通信速度を下
げてください。
Fig. 4
7. Click [E.P.R.], then the “Erase” screen appears. 7. ［E.P.R］をクリックすると、「Erase」画面が表示さ

(Fig. 5) れます。（Fig. 5）
8. Click [OK] to start writing. (Fig. 5) 8. ［OK］
をクリックして書き込みを開始します。
（Fig. 5）
CD-S300
Writing being executed.
書き込み中
Fig. 5
19
CD-S300
9. When writing of the firmware is completed, the 9. ファームウェアの書き込みが完了すると、以下の

screen appears as shown below. (Fig. 6) 画面が表示されます。
Click [OK]. (Fig. 6) ［OK］をクリックします。（Fig. 6）
10. Click [Exit] to end FlashSta.exe. (Fig. 6) 10.［Exit］をクリックし、FlashSta.exe を終了します。
（Fig. 6）
Fig. 6
11. Check that the firmware version is the same as 11. ファームウエアのバージョンが、書き込まれたも
written one by using the factory mode. のと同じであることをファクトリーモードで確認
CD-S300
します。
OPE: v1.09 Firmware version
* W h e n t h e f i r m w a re v e r s i o n i s d i ff e re n t ※ ファームウェアのバージョンが、書き込まれ
from written one, perform the “UPDATING たものと異なる場合、「ファームウェアの書き
FIRMWARE” procedure all over again. 込み」をもう一度やり直してください。
12. Press the “ ” (Power) switch of this unit to turn off 12. 本機の（電源）スイッチを押して電源を切り
the power. ます。
13. Disconnect the power cable of this unit from the 13. 本機の電源コードを AC コンセントから抜きます。
AC outlet.
20
CD-S300
● Initializing the EEPROM (IC304 of the MAIN ● EEPROM（MAIN P.C.B. の IC304）の初期化

P.C.B.)
Be sure to initialize the EEPROM (IC304 of the MAIN ファームウェアのアップデート後、下記の手順で
P.C.B.) by using the procedure below after updating EEPROM（MAIN P.C.B. の IC304）を必ず初期化して
the firmware, otherwise the set up information (CD/ ください。でなければ、設定情報（CD/USB モード、
USB mode, PURE DIRECT ON/OFF, RS-232C ON/ PURE DIRECT ON/OFF、RS-232C ON/OFF、DISC 有無）
OFF, and DISC loaded/unloaded) can not be が正常に記憶されません。
memorized properly. 1. 本機の電源コードを AC コンセントに接続します。
1. Connect the power cable of this unit to the AC 2. 本機の（再生）キーと（停止）キーを
outlet. 押しながら、（電源）スイッチを押して電源を
2. While pressing the “ ” (Play) key and the “ 入れます。
” (Stop) key of this unit, press the “ ” (Power) ファクトリーモードが起動します。
switch to turn on the power. 3. リモコンの CLEAR キーを押します。
The Factory mode is activated. EEPROM（MAIN P.C.B. の IC304）が初期化され、
3. Press the “CLEAR” key on the remote control. MEMORY CLEAR が表示されます。
The EEPROM (IC304 of the MAIN P.C.B.) is 4. 本機の（電源）スイッチを押して電源を切り
initialized, and “MEMORY CLEAR” is displayed. ます。
4. Press “ ” (Power) switch of this unit to turn off the 5. 本機の電源コードを AC コンセントから抜きます。
power.
5. Disconnect the power cable of this unit from the
AC outlet.
Remote control / リモコン
“CLEAR” key
FL display / FLディスプレイ
CLEAR キー
MEMORY CLEAR
CD-S300
21
CD-S300
■ DISPLAY DATA
● V701: 14-ST-68GINK (OPERATION P.C.B.)
52 1
● PIN CONNECTION
Pin No. 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36
Connection F2 NP NP GND VFL VDDH VDD OSC RESET CS CP DA TSA TSB NX NX NX
Pin No. 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19
Connection NX NX NX NX NX NX NX NX NX NX NX NX NX NX NX NX NX
Pin No. 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
Connection NX NX NX NX NX NX NX NX NX NX NX 14G 13G Q14G Q13G NP NP F1
Note: 1) F1, F2 ..... Filament 2) NP ..... No pin 3) NX ..... No extended pin 4) GND ..... GND pin 5) VFL ..... VFD driving voltage sink pin
6) VDD ..... Logic voltage supply pin 7) VDDH ..... VFD driving voltage source pin 8) CP ..... Shift register clock 9) DA ..... Serial data input 10) TSA, TSB ..... Test pin
11) CS ..... Chip select input pin 12) RESET ..... Reset input 13) OSC ..... Pin for self-oscillation 14) 13G, 14G ..... Grid 15) Q13G, Q14G ..... Driver output port
● GRID ASSIGNMENT
14G 13G
CD-S300
1G 2G 3G 4G 5G 6G 7G 8G 9G 10G 11G 12G
1-1 2-1 3-1 4-1 5-1
1-2 2-2 3-2 4-2 5-2
1-3 2-3 3-3 4-3 5-3
1-4 2-4 3-4 4-4 5-4
1-5 2-5 3-5 4-5 5-5
1-6 2-6 3-6 4-6 5-6
1-7 2-7 3-7 4-7 5-7
(1G – 12G)
● ANODE CONNECTION
1G – 12G 13G 14G 1G – 12G 13G 14G 1G – 12G 13G 14G
D0 1-1 – – D12 3-3 D24 5-5 — —
D1 2-1 – – D13 4-3 D25 1-6 — —
D2 3-1 – – D14 5-3 D26 2-6 — —
D3 4-1 – D15 1-4 D27 3-6 — —
D4 5-1 – D16 2-4 — D28 4-6 — —
D5 1-2 – D17 3-4 — — D29 5-6 — —
D6 2-2 – D18 4-4 — — D30 1-7 — —
D7 3-2 – D19 5-4 — — D31 2-7 — —
D8 4-2 – D20 1-5 — — D32 3-7 — —
D9 5-2 – D21 2-5 — — D33 4-7 — —
D10 1-3 D22 3-5 — — D34 5-7 — —
D11 2-3 D23 4-5 — —
22
CD-S300
■ IC DATA
IC2: LC786922E-01UY-E (MAIN P.C.B.)
CMOS LSI compact disc player IC
PCMDATA
PCMLRSY
PCMREQ
PCMBCK
DVDD15
LRVDD
CONT4
LRVSS
LRREF
RCHO
DOUT
DVDD
DVDD
LCHO
XVDD
XOUT
SLCO
DVSS
XVSS
PCMDATA
PCMLRSY
PCMREQ
XIN
PCMBCK
DVDD15
LRVDD
CONT4
LRVSS
LRREF
RCHO
DOUT
DVDD
DVDD
LCHO
XVDD
XOUT
SLCO
DVSS
XVSS
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61
XIN
LPF CLOCK
EFMIN 1 GENERATOR 60 LRSY
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
PCN Output Control
RFOUT 2 59 DATACK
EFMlN 1 60 LRSY
LPF 3 8FS DIGITAL FILTER/ Audio Output 58 DATA
SLICE Control RFOUT 2 59 DATACK
1 bit DAC
PHLPF 4 LEVEL 57 TEST LPF 3 58 DATA
CONTROL
LC786922
AIN 5 Stream Control/Audio Input 56 STDATA PHLPF 4 57 TEST
CIN 6 RF 55 STCK AIN 5 56 STDATA

Audio Control
SIGNAL MUTE/DEEMPHASIS/ MP3, WMA, CIN 6 55 STCK
BIN 7 PROCESSOR DECODER 54 STREQ
ATTENUATION CONTROL/
BIN 7 54 STREQ
6A01
DIN 8 BASS/TREBLE/ 53 MODE
HFC Filter Memory
MONITOR DIN 8 53 MODE
1 M Bit
SLCISET 9 52 CONT0
Memory I/F
SLCISET 9 52 CONT0
RFMON 10 VREF 51 CONT1 RFMON 10 51 CONT1
VREF 11 SRC 50 CONT2 VREF 11 50 CONT2

TES, HFL, INTERPOLATION MUTE
DEFECT JITTC 12 49 SUB_READY0
JITTC 12 49 SUB_READY0
System EIN 13 48 REG_READY0
EIN 13 ROM Control 48 REG_READY0
ERROR CORRECTION FIN 14 47 RESB
JITTER DECODER
FIN 14 47 RESB
PCNCNT 15 46 DO
PCNCNT 15 APC Synchronization TEXT 46 DO
MCU TE 16 45 DI
Detection DECODER
EFM I/F TEIN 17 44 CL
TE 16 45 DI
D/A Demodulation
LDD 18 43 CE
TEIN 17 SUBCODE 44 CL
SERVO DECODER LDS 19 42 DVSS
LDD 18 43 CE
A/D CONTROL AVSS 20 41 DVDD
LDS 19 DOUT Control 42 DVSS
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
AVSS 20 CD PLL PLL3 41 DVDD
PORT CONTROL
AVDD
FDO
TDO
SLDO
SPDO
VVSS1
PDOUT1
PDOUT0
PCKIST
VVDD1
CONT5
CONT3
DEFECT
FSEQ
C2F
DVDD
DVSS
DVDD15
VVDD3
VVSS3
21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
AVDD
FDO
TDO
SLDO
SPDO
VVSS1
PDOUT1
PDOUT0
PCKIST
VVDD1
CONT5
CONT3
DEFECT
FSEQ
C2F
DVDD
DVSS
DVDD15
VVDD3
VVSS3
Pin Function
I/O State During a Reset Detail of Function
No. Name
1 EFMlN Al Input RF signal input
2 RFOUT AO Undefined RF signal output
3 LPF AO Undefined RF signal DC level detection low-pass filter capacitor connection
CD-S300
4 PHLPF AO Undefined Defect detection low-pass filter capacitor connection
5 AIN AI Input A signal input
6 CIN Al Input C signal input
7 BIN AI Input B signal input
8 DIN AI Input D signal input
9 SLCISET AI Input SLCO output current setting resistor connection
10 RFMON AO Undefined IC internal analog signal monitor
11 VREF AO AVDD/2 VREF voltage output
12 JITTC AO Undefined Jitter detection capacitor connection
13 EIN AI Input E signal input
14 FIN AI Input F signal input
15 PCNCNT AI Input EFM PLL charge pump control voltage input
16 TE AO Undefined TE signal output
17 TEIN AI Input TE signal input used for TES signal generation
18 LDD AO Undefined Laser power control signal output
19 LDS AI Input Laser power detection signal input
20 AVSS — — Analog system ground / This pin must be connected to the 0 V level
21 AVDD — — Analog system power supply
22 FDO AO AVDD/2 Focus control signal output / D/A converter output
23 TDO AO AVDD/2 Tracking control signal output / D/A converter output
24 SLDO AO AVDD/2 Sled control signal output / D/A converter output
25 SPDO AO AVDD/2 Spindle control signal output / D/A converter output
26 VVSS1 — — Internal VCO ground / This pin must be connected to the 0 V level
27 PDOUT1 O Undefined Internal VCO control phase comparator output 1
28 PDOUT0 O Undefined For use by the EFM PLL circuit Internal VCO control phase comparator output 0
29 PCKIST AI Input PDOUT0, 1 output current setting resistor connection pin
30 VVDD1 — — Internal VCO power supply
31 CONT5 O Low General purpose output
32 CONT3 I/O Input General purpose input/output (Built-in pull-up resistor)
33 DEFECT I/O Input Monitor output pin (Defect detection signal output : High-active)
34 FSEQ I/O Input Monitor output pin (CD sync. signal detection output : High-active)
35 C2F I/O Input Monitor output pin (C2 error signal output : High-active)
23
CD-S300
Pin Function
I/O State During a Reset Detail of Function
No. Name
36 DVDD — — Digital system power supply
37 DVSS — — Digital system ground / This pin must be connected to the 0 V level
38 DVDD15 AO High Digital circuit power supply capacitor connection
39 VVDD3 — — Internal PLL power supply
40 VVSS3 — — Internal PLL ground / This pin must be connected to the 0 V level
43 CE I Input Host I/F : Chip enable signal input
44 CL I Input Host I/F : Data transfer clock input
Host microprocessor interface
45 DI I Input Host I/F : Data input
46 DO O Hi-Z (H) Host I/F : Data output (Trial-state output)
47 RESB I — IC reset input / This pin must be set low once after power is first applied
48 REG_READY0 O Low Host I/F : REG_READY output (Nch-opendrain output)
Host microprocessor interface
49 SUB_READY0 O Low Host I/F : SUB_READY output (Nch-opendrain output)
50 CONT2 I/O Input General purpose input/output
53 MODE I — Set input / This pin must be connected to the DVDD
54 STREQ I/O Input Stream data demand signal output
55 STCK I/O Input Stream data bit clock input
56 STDATA I/O Input Stream data input
57 TEST I — Test input / This pin must be connected to the 0 V level
58 DATA I/O Input Monitor pin / Audio data output
59 DATACK I/O Input Monitor pin / Audio bit clock output
60 LRSY I/O Input Monitor pin / Audio Left/Right channel clock output
62 PCMLRSY O Low Monitor pin / Audio Left/Right channel clock output
63 PCMBCK O Low Monitor pin / Audio data shift clock output
64 PCMDATA O Low Monitor pin / Audio data serial output
65 PCMREQ I Input Monitor pin / Audio data output request signal input
66 DVDD15 AO High Digital circuit power supply capacitor connection
CD-S300
69 DOUT O Low Monitor pin / Digital audio data output (EIAJ format)
70 CONT4 I/O Input (Low) General purpose input/output 4 (Initial : Input, internal pull-down resistor ON)
71 XVSS — — Oscillator ground / This pin must be connected to the 0 V level
72 XOUT O Oscillation 16.9344 MHz oscillation pins
Oscillation
73 XIN I Oscillation 16.9344 MHz oscillation pins
74 XVDD — — Oscillator power supply
75 LRVDD — — Left/Right channel power supply
76 LCHO AO LRVDD/2 Left channel output
77 LRREF AO LRVDD/2 Reference output for Left/Right channel
D/A Converter
78 RCHO AO LRVDD/2 Right channel output
Left/Right channel ground
79 LRVSS — —
This pin must be connected to the 0 V level
80 SLCO AO Undefined Slice level control output
Note
① For the unused pins:
• The unused input pins must be connected to the GND (0 V) level
• The unused output pins must be leave open (No connection)
• The unused input/output pins must be connected to the GND (0 V) or power supply pin for I/O in input pin mode or must be left open (No connection) in
output pin mode
② NC pins must be left open
③ For power supply pins:
• Same voltage must be supplied to DVDD, AVDD, XVDD, LRVDD, VVDD1, VVDD3 power supply pins (Refer to allowable operating ranges)
④ MODE pin must be connected to the DVDD
⑤ TEST pins must be connected to GND (0 V)
⑥ During power-on, RESB pin must be set to “Low” for more than 20 ms
⑦ Nch-opendrain output pin must put the pull-up resistance outside
24
CD-S300
IC7: LC87F1HC8A (MAIN P.C.B.)

CMOS LSI
Interrupt control IR PLA
Standby control FROM
CF USB PLL
RC Clock
PC
X’tal generator
SIO0 Bus interface ACC
SIO1 Port 0 B register
SIO4 Port 1 C register
SIO9 Port 2
ALU
Timer 0 Port 3
Timer 1 Port 7
PSW
Timer 4 INT0 to INT7

Noise filter RAR
Timer 5 UART1 RAM
Timer 6 Audio interface Stack pointer
CD-S300
Timer 7 ADC Watchdog timer
Infrared remote
Base timer control receiver circuit Onchip debugger
PWM0
PWM1
USB host
P24/INT5/INT7/SCK4
P05/AN5/CKO/SDAT
P07/AN7/T7O/LRCK
P06/AN6/T6O/BCLK
P25/INT5/SO9/RD9
P26/INT5/SI9/WR9
P22/INT4/SO4/RD
P23/INT4/SI4/WR
P04/AN4/DBGP2
P27/INT5/SCK9
P20/INT4/INT6
P21/INT4
36
36
34
33
32
31
30
29
28
27
26
25
UHD- 37 24 P03/AN3/DBGP1
UHD+ 38 23 P02/AN2/DBGP0
VDD3 39 22 P01/AN1
VSS3 40 21 P00/AN0
P34/UFILT 41 20 VSS2
P33/AFILT 42 19 VDD2
P32 43 18 PWM0/MCLKO
P31/URX1 44 17 PWM1/MCLKI
P30/UTX1 45 16 P17/T1PWMH/BUZ
P70/INT0/T0LCP/AN8 46 15 P16/T1PWML
P71/INT1/T0HCP/AN9 47 14 P15/SCK1
P72/INT2/T0IN 48 13 P14/SI1/SB1
12
10
11
1
2
3
4
5
6
7
8
9
P73/INT3/T0IN/RMIN
RES
XT1/AN10
XT2/AN11
VSS1
CF1
CF2
VDD1
P10/SO0
P11/SI0/SB0
P12/SCK0
P13/SO1
25
CD-S300
Pin No. Function Name I/O Detail of Function Option

5, 20, 40 VSS1, VSS2, VSS3 – - power supply No
8, 19 VDD1, VDD2 – + power supply No
39 VDD3 – USB reference voltage Yes
21, 22, 23, 24, 25, 26, 27, 28 Port 0 I/O • 8-bit I/O ports Yes
P00 to P07 • I/O specifiable in 4-bit units
• Pull-up resistors can be turned on and off in 4-bit units
• HOLD reset input
• Port 0 interrupt input
• Pin functions
AD converter input ports : AN0 to AN7 (P00 to P07)
On chip debugger pins : DBGP0 to DBGP2 (P02 to P04)
P05 : System clock output/audio interface SDAT input/output
P06 : Timer 6 toggle output/audio interface BCLK input/output
P07 : Timer 7 toggle output/audio interface LRCK input/output
• Pin functions
P10 : SIO0 data output
P11 : SIO0 data input/bus input/output
P12 : SIO0 clock input/output
P13 : SIO1 data output
P14 : SIO1 data input/bus input/output
P16 : Timer 1 PWML output
P17 : Timer 1 PWMH output/beeper output
• Pin functions
CD-S300
P20 to P23 : INT4 input/HOLD reset input/timer 1 event input/timer 0L capture input/
timer 0H capture input
P24 to P27 : INT5 input/HOLD reset input/timer 1 event input/timer 0L capture input/
timer 0H capture input
P20 : INT6 input/timer 0L capture 1 input
P22 : SIO4 data input/output/parallel interface RD output
P23 : SIO4 data input/output/parallel interface WR output
P24 : SIO4 clock input/output/lNT7 input/timer 0H capture 1 input
P25 : SIO9 data input/output/parallel interface RD9 output
P26 : SIO9 data input/output/parallel interface WR9 output
Interrupt acknowledge types
Rising
Rising Falling and H level L level
Falling
INT4 enable enable enable disable disable
41, 42, 43, 44, 45 Port 3 I/O • 5-bit I/O ports Yes
• Pin functions
P30 : UART1 transmit
P31 : UART1 receive
P33 : Audio interface PLL filter pin
P34 : USB interface PLL filter pin
26
CD-S300
Pin No. Function Name I/O Detail of Function Option

1, 46, 47, 48 Port 7 I/O • 4-bit I/O port No
• Pin functions
P70 : INT0 input/HOLD reset input/timer 0L capture input/watchdog timer output
P71 : INT1 input/HOLD reset input/timer 0H capture input

P72 : INT2 input/HOLD reset input/timer 0 event input/timer 0L capture input/high
speed clock counter input
P73 : INT3 input (input with noise filter)/timer 0 event input/timer 0H capture input/IR
remote control receiver input
AD converter input ports : AN8 (P70), AN9 (P71)
Interrupt acknowledge types
Rising
Rising Falling and H level L level
Falling
INT0 enable enable disable enable enable
INT1 enable enable disable enable enable
18 PWM0 I/O PWM0, PWM1 output port No

17 PWM1 General-purpose input port
• Pin functions
PWM0 : Audio interface master clock output
PWM1 : Audio interface master clock input
37 UHD- I/O USB data I/O pin UHD-/general-purpose I/O port No
38 UHD+ I/O USB data I/O pin UHD+/general-purpose I/O port No
2 RES I Reset pin No
3 XT1 I • 32.768 kHz crystal oscillator input No
CD-S300
• Pin functions
General-purpose input port
AD converter input ports : AN10
Must be connected to VDD1 when not to be used
4 XT2 I/O • 32.768 kHz crystal oscillator output No
• Pin functions
General-purpose I/O
AD converter input port : AN11
Must be set for oscillation and kept open if not to be used
6 CF1 I Ceramic/crystal resonator input No
7 CF2 I Ceramic/crystal resonator output No
27
CD-S300
IC305: R5F212CASNFP (MAIN P.C.B.)

Single chip 16-bit microprocessor
8 8 8 8 3 2 8
I/O ports Port P0 Port P1 Port P2 Port P3 Port P4 Port P5
Port P6
Peripheral functions
UART or System clock
8
clock synchronous serial I/O generation circuit
Timers (8 bits x 3)
XIN-XOUT
Port P7
High-speed on-chip oscillator
Timer RA (8 bits x 1) I2C bus or SSU Low-speed on-chip oscillator
Timer RB (8 bits x 1) (8 bits x 1) XCIN-XCOUT
8
Timer RC (16 bits x 1)
Timer RD (16 bits x 2)
Timer RE (8 bits x 1)
Timer RF (16 bits x 1)
Port P8
LIN module
8
Watchdog timer
(15 bits)
Port P9
A/D converter
4
(10 bits x 20 channels)
D/A converter R8C/Tiny Series microprocessor core Memory

(8 bits x 2)
R0H R0L SB ROM(1)

R1H R1L USP
R2
R3 ISP NOTES:
INTB RAM(2) 1. ROM size varies with MCU type.
A0 PC 2. RAM size varies with MCU type.
A1
FB FLG
Multiplier
CD-S300
52 REG_READY0
53 SUB_READY0
43 DOUT_MUTE
57 POFF_detect
56 KEY_PLAY
51 DSP_/RST
44 CD_MUTE
55 KEY_USB
54 KEY_O/C
46 232C_RX
45 232C_TX
50 DSP_CE
60 KEY_2
59 KEY_1
58 KEY_0
42 TBL_R
41 TBL_L
48 RxD2
47 CLK2
49 TxD2
D33_Detect 61 40 CL_UP
OPU_SEL 62 39 CL_DOWN
DRV_MUTE 63 38 OPEN
LIMIT_SW 64 37 CLOSE
MON_1 65 36 RIN2
MON_2 66 35 DOUT2
N.C. 67 34 USB_TX
N.C. 68 33 USB_RX
N.C. 69 32 USB_/RST
LED_POWER 70 IC305 31 C2_Flag
LED_PDIRECT 71 R5F212CASNFP 30 CANCEL
LED_/USB1 72 29 USB_IN
LED_/USB2 73 28 iPod_IF
N.C. 74 27 HSW_/EN
VSS/AVSS 75 26 HSW_/FLG
SLED_CTL 76 25 USB_PCON
VREF 77 24 TBL_POS
VCC/AVCC 78 23 UPSW
STBY 79 22 DOWNSW
EEP_SCL 80 21 OPSW
XOUT 10
VSS/AVSS 11
XIN 12
VCC/AVCC 13
232C_PCON 14
IR 15
FL_/RST 16
FL_CLK 17
FL_DATA 18
FL_CS 19
CLSW 20
EEP_WP 1
EEP_SDA 2
DAC_/CS 3
DAC_SCL 4
DAC_SDA 5
OCD_MODE 6
/AMUTE 7
ABUS_SW 8
RESET 9
28
CD-S300
Pin No. Function Name I/O Detail of Function

1 EEP_WP O Wright protection of EEPROM (IC304)
2 EEP_SDA O Serial data to EEPROM (IC304)
3 DAC_/CS O Chip select to audio DAC (IC302)
4 DAC_SCL O Serial clock to audio DAC (IC302)
5 DAC_SDA O Serial data output to audio DAC (IC302)
6 OCD_MODE I Input High --> Normal, Low --> Writing ROM mode
7 /AMUTE O Muting control signal to audio circuit High --> Muting is active
8 ABUS_SW O No use
9 RESET I Input RESET signal of IC305
10 XOUT O Oscillator OUT
11 VSS/AVSS GND DGND
12 XIN I Oscillator IN
13 VCC/AVCC Power D+3.3V
14 232C_PCON O
15 IR I Input the signal from remote control
16 FL_/RST O RESET signal to FL-display
17 FL_CLK O Serial clock to FL-display (V701)
18 FL_DATA O Serial data output to FL-display (V701)
19 FL_CS O Chip select to FL-display (V701)
20 CLSW I
21 OPSW I Detect OPEN SW of CD-loader mechanism
22 DOWNSW I
23 UPSW I Detect CLAMP-UP SW of CD-Loader mechanism
24 TBL_POS I
25 USB_PCON O Control IC301(DC/DC converter) and USB+5V is ON/OFF
High --> USB+5V is supplied
CD-S300
26 HSW_/FLG I Detect the status of IC6 (current limiter) High --> Normal, Low --> Over current
27 HSW_/EN O Control IC6 (current limiter) Low --> Enable output
28 iPod_IF I Control signal from iPod to change communication format
29 USB_IN I Detect to plug in USB memory or iPod High --> Detect USB memory or iPod
30 CANCEL I Request signal for cancel busy condition
31 C2_Flag I Input FMON2 (C2F) signal from CD-DSP (IC2)
32 USB_/RST O RESET signal to USB-ucom (IC7)
33 USB_RX I RX signal from USB-ucom (IC7)
34 USB_TX O TX signal to USB-ucom (IC7)
35 DOUT2 O Reserved (for 232C)
36 RIN2 I Reserved (for 232C)
37 CLOSE O Control signal for closing tray
38 OPEN O Control signal for opening tray
39 CL_DOWN O
40 CL_UP O
41 TBL_L O
42 TBL_R O
43 DOUT_MUTE O Muting digital-out signal on pure direct
Low --> Digital-output signal is muting
44 CD_MUTE I Detect the muting control signal from CD-DSP (IC2) during loading disc or searching track
45 232C_TX O
46 232C_RX I
47 CLK2 O Output the clock signal to CD-DSP
48 RxD2 I Input the status signal from CD-DSP
49 TxD2 O Output the status signal to CD-DSP
50 DSP_CE O Output chip_enable signal to CD-DSP
29
CD-S300
Pin No. Function Name I/O Detail of Function

51 DSP_/RST O Reset signal to CD-DSP
52 REG_READY0 I Input R_RDY signal from CD-DSP
53 SUB_READY0 I Input S_RDY signal from CD-DSP
54 KEY_O/C I
55 KEY_USB I
56 KEY_PLAY I
57 POFF_detect I Detect PRIMARY_POWER_OFF condition
58 KEY_0 I Detect KEY_0 signal on front-panel
STOP, PAUSE, O/C
PLAY, SKIP+, SKIP-
Pure direct, CD/USB
61 D33 Detect I Reserved (Detect D+3.3)
62 OPU_SEL I Input the signal to select OPU
0V : CD traverse 3.3V : DVD/CD traverse
1.65V : DVD/CD traverse
63 DRV_MUTE O Mute control to actuator driver (IC1) Low --> Muting output on actuator driver
64 LIMIT_SW I Detect inner position SW on CD-traverse mechanism
65 MON_1 I Input FMON0 (defect) signal from CD-DSP (IC2)
66 MON_2 I Input FMON1(FSEQ) signal from CD-DSP (IC2)
67 N.C.
68 N.C.
69 N.C.
70 LED_POWER O Control LED_POWER on front-panel
71 LED_PDIRECT O Control LED_PURE DIRECT on front-panel
CD-S300
72 LED_USB1 O Control LED_USB (orange) on front-panel

73 LED_USB2 O Control LED_USB (green) on front-panel
74 N.C.
75 VSS/AVSS GND DGND
76 SLED_CTL O Reserved
77 VREF Power Input the reference voltage (D+3.3V) for A/D port (pin 58–60, pin 62)
78 VCC/AVCC Power Input D+3.3V
79 STBY O
80 EEP_SCL O Serial clock to EEPROM (IC304)
Key detection for A/D port

Key input (A/D) pull-up resistance 10 k-ohms
Ohm 0 +820 +3.3 k +12.0 k

V 0 0.2–0.3 0.9–1.0 2.0–2.1
A/D value (3.3 V = 255) 0 15–25 70–78 153–162
KEY0 (58 pin) — STOP PAUSE OPEN/CLOSE
KEY1 (59 pin) — PLAY SKIP +/SEARCH + SKIP -/SEARCH -
Ohm 0 +100 +3.3 k +12.0 k

V 0 0.03-0.1 0.8–0.9 2.0–2.1
A/D value (3.3 V = 255) 0 3–7 60–70 150–160
KEY2 (60 pin) — PURE DIRECT CD/USB —
30
CD-S300
■ PIN CONNECTION DIAGRAMS

• ICs
BD5229G-TR BD9870FPS-E2 KIA7805API KIA79M05PI-U
4
5
3 1
1 IN GND
5 OUT OUTPUT
COM INPUT
LA6565-TE-L-E LC786922E-01UY-E LC87F1HC8A-F5AL1-E LE24C023M-TLM-E
60 41
61 40 36 25
37 24
18
8 4
36
80 21 1
48 13
1 1 12
1 20
MFI341S2161 NJM2068D-D PCM1780DBQR R1172S331B-E2-F
15 11
16 10
6
8 3
CD-S300
6 4 16
20 8 1
5 1 1
1
R5523N001A-TR-F R5F212CASNFP TC7SH08F TC7SH08FU
60 41
61 40
4 4 4
5 5 5
3 3 3
1 1 1
80 21
1 20
31
CD-S300
• Diodes
1SS355 1T2 2A02-05 XO MAZ8047GHL 4.9V
Anode Anode
Anode Anode
Cathode Cathode Cathode Cathode
MTZJ5.6B 5.6V RB050LA-40TR TP

MTZJ6.2B 6.2V RB501V-40
MTZJ7.5B 7.5V
MTZJ8.2A 8.2V Anode
Anode
MTZJ30A 30V
Cathode Cathode
• Transistors
2SA1037K 2SA1708 2SC2412K 2SC3852

CD-S300
C C
E B E
B C B
E
B
CE
2SD1938F 2SD2394 12A01C-TB-E DTA114EKA

DTC114EKA
DTC144EKA
C C 3
E E 1 1: GND
2: IN
B B 2 3: OUT
B
E
C
32
A B C D E F G H I J
CD-S300
1 ■ BLOCK DIAGRAM
Front section
V701 D702, 703, 751 SW701-708 U701
POWER Indicator OPERATION (1) – (3)
CB752
FL-Display Pure Direct Indicator Front Panel Keys REM r 4FFQBHF→
USB connector
USB Indicator SCHEMATIC DIAGRAM
D+/D-
2
Loader Mechanism Unit USB+5 MAIN r 4FFQBHF →
KEYxxxx
LEDxxxx
IC8 IC6 FL_CLK/FL_Data
APPLE Current Limiter FL_CS/FL SCHEMATIC DIAGRAM
Authentication
IR
MFI341S2161 37,38
16-19 70-73 54-56,58-60
IC7 USB_/EN, USB_FLG
USB Interface IC305
LC87F1HC8A 15
Microprocessor
D+3.3V USB_TX, RES_USB
rFILE Read/Write R5F212CASNFP
riPod Authentication
6 7 USB_RX, USB_IN RES_DSP D+3.3V
XL2 XL1 rIC2/IC7Control
DSP_CLK
12MHz 73 16.9344 72 rFL/IndicatorControl
DSP_CE
3 DSP_DI
r IR/Key Detect
Limit SW IC2 r DAC Control
9 IC306
A, B, C, D, E, F, PD CD-Controller rOPEN/CLOSE Control
Reset IC
LC786922 riPod Operation (iAP)
DSP_DO BD5229G
OPU rDisc Control（Servo） S_RD 37,38 64 3-5 7 10 12 1,2
Focus rEFM Demodulation
YR_RD IC304
Tracking LD, F+/F-, T+/T- rMP3/WMA Decode
YCD_MUTE XL301 EEPROM
rDigital Audio Output（I2S/SPDIF) 10MHz LE24C023M
Spindle Feed
69
U301
OPEN/CLOSE
IC1 OPTICAL
IC4
Actuator Driver
TC7SH08
4 LA6565
SPDIF DIGITAL OUT
LIMIT SW PJ301
M+7V Switch
M Q304
COAXIAL
/ Buffer Buffer
CLAMP UP/DOWN, OPEN/CLOSE MCLK, BCK
LRCK, DATA
A_MUTE
IC302
Audio DAC DAC Control (SPI)
PCM1780
IC303
5 D+5V Liner Regulator
POWER and AUDIO D+3.3V
OPERATION (4) – (6), (8)
r 4FFQBHF →
SCHEMATIC DIAGRAM
IC301
-B1 IC803 L ch R ch B+2 DC/DC Converter
C817 A-5
SW801 USB+5
F801 T801 IC802 IC602 IC601
A+5 3dB AMP 3dB AMP
AC IN D805, 806, 809, 810 / LPF / LPF
POWER ON/OFF
+B1 IC801
C816 D+5 Mute Control
6 Mute Circuit
D803, 804
Q806
+B2 Q804 Power Up/Down
C813 M+7 Mute Control
(P_MUTE)
D802 L ch R ch
Q801 ANALOG OUT

FL -27V
FL AC+/-
7
Power Transformer
33
A B C D E F G H I J
CD-S300
POINT A XL1 (Pin 72 of IC2) POINT B XL2 (Pin 6 of IC7)

■ PRINTED CIRCUIT BOARDS POINT C XL301 (Pin 10 of IC305) POINT D 1 / IC306 (2 pin), 2 / IC306 (1 pin)
1
MAIN P.C.B. (Side A) IC306 1 IC306 1

(2 pin) (2 pin)
IC306 2 IC306 2
(1 pin) (1 pin)
2
GND POWER ON POWER OFF POWER ON
OPERATION (9) LIMIT SW
(CB901) SLED M-
To Loader mechanism unit
OCD_MODE
SLED M+ D
SPINDLE M-
232C_RX
232C_TX
+SUB33
SPINDLE M+
DGND
2 1
To Loader mechanism unit C (Writing port)
CB310
CLOSE SW CB305
GND
OPEN SW
SPINDLE M-
3 SPINDLE M+
4 1
IC306
5 3
18 19
CB3
F-
F+
T+
IC1
T-
C
D 1 20
MSW 21
80
CB2
RF
A 1 36
B IC305
F
4 RFGND 61 40
Vc 60 41
1
IC301
Vcc
CB1
E 5
N.C.
CD_VR CB304
DVD_VR
CD_LD
PD
FL_CS
FL_CLK
D+3.3V
DGND
LED_PDIRECT
LED_/USB2
KEY_1
DGND
HFM
N.C.
DVD_LD
LD_GND 3 4
25 36 IC6
1 5
24 M2GND
CB6
1 5 37
IC7
20 6 +B2
FL_DATA
FL_/RST
REM
LED_POWER
LED_/USB1
KEY_0
KEY_2
1 20
5 80 21 IC8 M+7
16 1013
15 11 48 M1GND
OPTICAL 12 1
DGND
CB301
D+5
IC2
A+5
DIGITAL AGND
OUTPUT A-5 OPERATION (1)
OUT 61 40
60 41 3 4 P_MUTE (CB701)
IC303
1 6
COAXIAL OPERATION (8)
8 9
(CB806)
IC302
3 1
IC4
4 5 1 16
6
• Semiconductor Location
CB303
Ref no. Location Ref no. Location
AGND
VOUTL
AGND
VOUTR
A+5
A-5
AMUTE
B D2 E5 IC8 E5
A
VCC D3 E5 IC301 G4
D- D302 E6 IC302 E6
OPERATION (4) D+
(CB601) GND D308 F4 IC303 F6
FG IC1 D4 IC305 E4
IC2 C5 IC306 F3
OPERATION (3) IC4 C6 Q1 C4
(W751)
IC6 F5 Q309 F5
7
No replacement part available. IC7 F5
サービス部品供給なし
34
A B C D E F G H I J
CD-S300
MAIN P.C.B. (Side B)
4 1
IC304
5 8
Ref no. Location
D1 C6
D6 E5
D301 E6
D303 G4
D304 E6
D305 E6
D309 E6
5
IC304 E3
Q301 E6
Q304 B6
35
A B C D E F G H I J
CD-S300
OPERATION (1) P.C.B. (Side A) OPERATION (2) P.C.B. (Side A) OPERATION (3) P.C.B. (Side A)
LED_POWER
MAIN
DGND
(CB6)
GND
VCC
FG
D+
D-
D+3.3V
A B
① ② ③
2
OR GR CB753
W751
MAIN
(CB304)
LED_POWER
W701B
iPod/USB
LED_/USB1
FL_DATA
indicator
FL_/RST
KEY_2
KEY_0
OPERATION (8)
(CB807) REM CB752
iPod/USB
LED_PDIRECT
LED_POWER
FLGND
LED_/USB2
ACFL1 POWER
ACFL2
FL_CLK
D+3.3V
FL_/CS
D+3.3V
indicator
KEY_1
-27
DGND
DGND
DGND
W703
CB701
PURE DIRECT W701A
indicator
W702
4
PURE
DIRECT
CD/USB
5 OPERATION (4) P.C.B. (Side A)
1 8
IC601
Ref no. Location

4 5 ANALOG OUTPUT D702 I4
L/R
OUT D703 F3
6 D751 H2
D752 H3
1 8
IC601 D6
IC602
IC602 D6
4 5
CB601
AMUTE
A-5
A+5
VOUTR
AGND
VOUTL
AGND
7
MAIN
(CB303)
36
A B C D E F G H I J
CD-S300
OPERATION (1) P.C.B. (Side B) OPERATION (2) P.C.B. (Side B) OPERATION (3) P.C.B. (Side B)
5 4
IC702
4
1 3
5 OPERATION (4) P.C.B. (Side B)
Ref no. Location
IC702 D4
Q601 E6
Q602 E6
Q603 E6
6 Q604 E6
Q701 E4
Q702 J4
Q703 I4
Q704 J3
Q705 F4
Q706 J4
37
A B C D E F G H I J
CD-S300
OPERATION (5) P.C.B. (Side A) OPERATION (7) P.C.B. (Side A)

R, L models
T, A, G, J models
YELLOW ORANGE RED BROWN GRAY

RED BROWN GRAY YELLOW ORANGE
W805B W806A
2 W802A W801A W805A W804A W803A
W804B W803B W802B W801B
WHITE
W806B
YELLOW AC IN
110V 230-240V
120V 220V
CB804
VOLTAGE
SELECTOR
OPERATION (8)
(W807)
POWER
TRANSFORMER R, L models
4
OPERATION (6) P.C.B. (Side A) OPERATION (9) P.C.B. (Side A) OPERATION (10) P.C.B. (Side A)
5
Writing port
CB902
CB803
POWER
ON/OFF D+3.3V
6 232C_RX
CB901
232C_TX
OSD_MODE
DGND
MAIN
(CB310)
38
A B C D E F G H I J
CD-S300
OPERATION (5) P.C.B. (Side B) OPERATION (7) P.C.B. (Side B)

R, L models
OPERATION (6) P.C.B. (Side B) OPERATION (9) P.C.B. (Side B) OPERATION (10) P.C.B. (Side B)
5
Ref no. Location
Q901 F6
39
A B C D E F G H I J
CD-S300
OPERATION (8) P.C.B. (Side A) OPERATION (8) P.C.B. (Side B)
OPERATION (5)
(CB804)
W807
4 Ref no. Location

M2GND D801 D4
+B2
M+7 D802 D4
M1GND D803 C2
CB806
DGND D804 C2
D+5 IC802
A+5 D805 C3
AGND 3 1 1 IC803 3
D806 D3
A-5
P_MUTE D807 C3
D808 C3
MAIN D809 C3
(CB301) D810 D3
5 D811 D5
D812 H5
D813 H6
D814 C5
D815 H4
D816 B3
D817 G6
1 IC801 3 D818 G3
D819 H4
D820 H5
6 D821 H5
D822 C6
CB807
IC801 B6
IC802 C4
IC803 C4
Q801 D5
Q804 B3
Q806 H6
FLGND
ACFL1
ACFL2
-27
7
OPERATION (1)
(W702)
40
A B C D E F G H I J K L M N
CD-S300
SCHEMATIC DIAGRAMS
MAIN 1/2
1
SWITCH/
3.3
BUFFER ANALOG OUT
3.3
1.7
2 IC4 1.7
CURRENT LIMITER
0
DIGITAL OUT
IC6
0
IC5
3.2
0
2.4
3.3
iPod/USB IN
CB6
0
3
0
0
CD IN
0
1.6
1.6
0
1.7
1.8
3.3
3.3
1.7
3.3
3.3
3.3
1.7
1.7
1.7
0
3.3
Page 43 M8
2.0
3.3
0
0
0
CB1
3.3
1.8 1.7 to OPERATION (3)_W751
0
0
0
0
1.7
1.7 1.7
0
1.7 A 1.2
0 0
2.4 0
5.0 3.3 0
1.8 0
4 0.2
1.8
CD CONTROLLER 0
3.4
USB INTERFACE 0
2.0 0 0
1.8 3.3
0.2 0 0
1.8
0 3.3
1.8 0
1.8 0
IC7
0 1.8 0
3.3
IC2
1.8 1.7 0 B
3.4 0
3.3 1.7
5.0 3.1
3.2
0
3.1
iPod/USB IN 3.3
1.7 3.2
1.8 3.3 0
0 0.2
1.8 3.2 0
3.3
1.8 3.1 0 0
2.4 1.8 3.2
1.8
1.7 3.2
1.8
1.7
3.2
2.0
3.3
0
1.9
0.6
0.6
0
0
0
0
0
0
2.4
5 5.0 CB4
3.3
0.2 0
1.8
0 3.3
1.8
3.3
3.4
3.3
1.7
1.7
3.3
3.3
0
1.7
1.7
0.9
0
0
3.3
1.7
0
1.8
1.2
3.3
3.3
3.3
1.7
3.3
3.5
CB5
3.4
0
0
0
3.3 3.3
3.3 3.3
To Loader mechanism unit 0
6
3.3
0
0 3.3
0 4.0
7.2 3.3
CB2
0.3 0.3 3.3
IC1
0.3
0.3 1.7
3.3
3.3 1.7
0 3.4
0 3.3 1.7
0.2
7 3.3
0 3.3
0 0 0 3.3
0
IC8
0
3.2 3.2 1.0 0
3.4 0
3.4
0 0 0.3
3.4 3.4 0.3 No replacement part available.
3.5 7.3 1.7 サービス部品供給なし
3.1 7.3 1.7
1.7 1.7
CB3 IC1: LA6565-TE-L-E IC2: LC786922E-01UY-E IC7: LC87F1HC8A-F5AL1-E
1.7 1.7
Power amplifier 5-channel built-in CMOS LSI compact disc player IC CMOS LSI
1.7
To Loader mechanism unit 1.7
8
PCMDATA
PCMLRSY
Unit
PCMREQ
PCMBCK
DVDD15
Resistance: ohm Interrupt control IR PLA
LRVDD
CONT4
LRVSS
LRREF
RCHO
DOUT
DVDD
DVDD
LCHO
XVDD
XOUT
SLCO
DVSS
XVSS
XIN
Thermal Shutdown Signal System GND
FWD 1 36 SGND
Input
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61
Standby control FROM
(LOAD output voltage setting)
REV 2 35 VCONT
LPF CLOCK
ACTUATOR DRIVER VCCP2 3

MUTE
Turns ON/OFF a
CH1 34 MUTE1 EFMIN 1 GENERATOR
PCM Output Control
60 LRSY
CF
RC
USB PLL
Clock
corresponding CH RFOUT 2 59 DATACK PC
Level Shift Output Control

H: Output ON X’tal generator
VLO- 4 L: Output OFF
CH2,3,4 33 MUTE234 Audio Output
LPF 3 8FS DIGITAL FILTER/ 58 DATA
44k SLICE Control
1 bit DAC
11k PHLPF 4 LEVEL 57 TEST
VLO+ 5 - 32 VIN4- CONTROL
- + SIO0 Bus interface ACC
+ AIN 5 Stream Control/Audio Input 56 STDATA
To VREFOUT
VO4+ 6 31 VIN4
CIN 6 RF Audio Control 55 STCK SIO1 Port 0 B register
- SIGNAL MUTE/DEEMPHASIS/ MP3, WMA,
BIN 7 PROCESSOR DECODER 54 STREQ
VO4- 7 + 30 VREF_IN ATTENUATION CONTROL/
BASS/TREBLE/ SIO4 Port 1 C register
DIN 8 Memory 53 MODE
MONITOR HFC Filter
Level Shift
VO3+ 8 29 VREF_OUT 1 M Bit
SLCISET 9 52 CONT0
Memory I/F
SIO9 Port 2
IC6: R5523N001A-TR-F IC8: MFI341S2161 VO3- 9 28 REG_OUT

RFMON 10 VREF 51 CONT1 ALU
IC4: TC7SH08FU High side switch IC IC digital Power System GND REG_IN
(VCC)
Power VREF 11
TES, HFL,
SRC 50 CONT2 Timer 0 Port 3
- System INTERPOLATION MUTE
9 POINT A XL1 (Pin 72 of IC2) POINT B XL2 (Pin 6 of IC7) 2-input AND gate
FR
-
+
+
REG_OUT
GND
FR
JITTC 12 DEFECT
ROM
System
49 SUB_READY0
Timer 1 Port 7
PSW
EIN 13 ERROR CORRECTION Control 48 REG_READY0
P4/IRQ DECODER
P3/IRQ JITTER
Vcc H8/300H FIN 14 47 RESB Timer 4 INT0 to INT7
VIN 4 5 VOUT I/O port P2/IRQ
Vss MICROPROCESSOR Noise filter RAR
Level Shift
P1/IRQ
IN B 1 5 VCC VO2+ 10 +
-
27 REG_IN PCNCNT 15 APC Synchronization
Detection
TEXT
MCU
46 DO
DECODER
RNG I/F Timer 5 UART1 RAM
System control WDT TE 16 EFM 45 DI
FMU VO2- 11 26 VIN+OP Demodulation
Security logic D/A
IN A 2 EN 1
GATE CURRENT
Internal address bus
Voltage monitoring circuit +
-
TEIN 17 SUBCODE 44 CL Timer 6 Audio interface Stack pointer
Level Shift
CONTROL LIMIT VO1- 12 25 VIN-OP SERVO DECODER
ROM (112 kbytes) LDD 18 43 CE
A/D CONTROL
FLAG Internal data bus Timer 7 ADC
GND 3 4 OUT Y DELAY RES RAM (4 kbytes) VO1+ 13 24 VO_OP
LDS 19 DOUT Control 42 DVSS Watchdog timer
3 FLG AVSS 20 CD PLL PLL3 41 DVDD Infrared remote

UVLO Power-on Base timer
EEPROM (16 kbytes + 2 kbytes) PORT CONTROL control receiver circuit Onchip debugger
reset circuit VCCP1 14 23 VIN3
NC
NC
NC
NC
NC
44k
Interval timer 1 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 PWM0
THERMAL VCCS 15 11k - 22 VIN3-
Power System GND
-
AVDD
FDO
TDO
SLDO
SPDO
VVSS1
PDOUT1
PDOUT0
PCKIST
VVDD1
CONT5
CONT3
DEFECT
FSEQ
C2F
DVDD
DVSS
DVDD15
VVDD3
VVSS3
SHUTDOWN 20 19 18 17 16 +
Interval timer 2 +
2 NC 1 15 NC 44k To VREFOUT PWM1
VIN1+ 16 21 VIN2
On-chip 11k
GND Modular multiplication Register P4/IRQ 2 14 P3/IRQ + -
oscillator -
coprocessor (512 bytes) + 44k
3 Top view 13 USB host
NC P1/IRQ VIN1- 17 11k 20 VIN2-
-
- +
RES 4 12 P2/IRQ +
VIN1 18 19 VIN2+
5 11
10 Vcc
6 7 8 9 10
Vss
NC
NC
NC
NC
NC
★ All voltages are measured with a 10MΩ/V DC electronic voltmeter. ● 電圧は、内部抵抗 10MΩの電圧計で測定したものです。
★ Components having special characteristics are marked and must be replaced ● 印のある部品は、安全性確保部品を示しています。部品の交換が必要な場合、
with parts having specifications equal to those originally installed. パーツリストに記載されている部品を使用してください。
★ Schematic diagram is subject to change without notice. ● 本回路図は標準回路図です。改良のため予告なく変更することがございます。
41
CD-S300
MAIN 2/2
1 Page 43 B5
Page 44 B3
to OPERATION (1)_CB701
CB306
CB304
CB310
DIGITAL OUT
0
3.3
3.3
0
5.0
3.3
0
3.3
3.3
0
OPTICAL
CB311
1.7
3.3
3.3
3.3
3.3
3.3
0
3.3
3.3
3.3
3.1
0
2.8
2
OUTPUT
DIGITAL
5.0 OUT
2.8
2.2
COAXIAL
DC/DC CONVERTER
12.2 2.4
3
IC301 IC309
IC309
IC309
12.2
2.4
0
0.5
0
IC309
3.1
0.2
3.3
3.3
0.6
3.2
3.2
3.2
3.3
3.3
2.4
3.3
3.3
3.3
0
3.3
3.3
3.3
0
3.3
0 IC309
4
3.3 0
0 0
3.3 0
0 0
1.7 0
0 MICROPROCESSOR 0
0 0 CB308
CB301 0 5.0 3.3 3.3
0
12.2
IC303 0 3.3
7.3 5.0 5.0 5.0 3.3 IC305
3.3 0.9
0 0 0
3.3 0 IC307
5 0
3.3 0
5.0
Page 45 M4 5.0
3.3 0
to OPERATION (8)_CB806 5.0
0 3.2
0
LINER 0 3.3
-5.0
-4.4
REGULATOR 0 0
3.3 0
3.3 C 0
CB302
3.3 3.3 3.3
-4.5 3.3
3.3
0
0
0
6
1.7
1.5
3.3
3.3
3.3
0.2
3.3
3.3
3.1
2.8
3.3
3.3
3.3
3.3
0
0
JK301
3.3
3.3
IC308
3.3 3.3
3.3
3.3
3.3
3.3 3.3
3.3 IC313
JK302
3.3 3.3
-4.5
3.3
0
-4.5
IC304
3.3
EEPROM 3.3
-4.5 -4.5 0 3.3

7
0
ANALOG OUT L
0
0
2.5 2.5 3.3
IC302
0
2.5 3.3
2.5
Page 44 B6
5.0
2.5 1.6
RESET IC
0 1.2 IC306 2
to OPERATION (4)_CB601 -5.0 5.0 1.7
-4.5 3.3 1.8
1.7
ANALOG OUT CB305
3.3 3.3 Key detection for A/D port
CB303 1.7
3.3 Key input (A/D) pull-up resistance 10 k-ohms
(Writing port) D
3.3 Ohm 0 + 820 + 3.3 k + 12.0 k
AUDIO DAC 0
V 0 0.2 – 0.3 0.9 – 1.0 2.0 – 2.1
8 A/D value (3.3V=255)
KEY0 (58 pin)
0
–
15 – 25
STOP
70 – 78
PAUSE
153 – 162
OPEN/CLOSE
1 KEY1 (59 pin) – PLAY SKIP +/SEARCH + SKIP -/SEARCH -
Ohm 0 + 100 + 3.3 k + 12.0 k

V 0 0.03 – 0.1 0.8 – 0.9 2.0 – 2.1
A/D value (3.3V=255) 0 3–7 60 – 70 150 – 160
POINT C XL301 (Pin 10 of IC305) POINT D 1 / IC306 (2 pin), 2 / CB306 (1 pin) KEY2 (60 pin) – PURE DIRECT CD/USB –
IC301: BD9870FPS-E2 IC302: PCM1780DBQR
High stand voltage 1 channel step-down switching regulator Audio digital-to-analog converter IC305: R5F212CASNFP
VCC
Single chip 16 bit microprocessor
1 BCK
LRCK Audio 8 8 8 8 3 2 8
Serial Output Amp VOUTL
DATA Port DAC and
VREF
Low Pass Filter
PWM COMP DRIVER 4/8 IC306 1 IC306 1 I/O ports Port P0 Port P1 Port P2 Port P3 Port P4 Port P5
Oversampling
Digital
Enhanced
Multilevel
(2 pin) (2 pin)
Port P6
(FMT) Filter VCOM Peripheral functions
9 OSC
MS (DEMP0)
With
Function
Delta Sigma
Modulator
UART or System clock
8
STBY Serial Control clock synchronous serial I/O generation circuit
Control
5 STBY
MC (DEMP1)
Port Output Amp IC306 2 IC306 2 Timers (8 bits x 3)
XIN-XOUT
DAC and
(1 pin) (1 pin)
Port P7
CTL MD (MUTE)
High-speed on-chip oscillator
OUT Low Pass Filter VOUTR Timer RA (8 bits x 1) I2C bus or SSU Low-speed on-chip oscillator
LOGIC
Timer RB (8 bits x 1) (8 bits x 1) XCIN-XCOUT
8
2 Timer RC (16 bits x 1)
(TEST) Timer RD (16 bits x 2)
TSD OCP
System Clock POWER ON POWER OFF POWER ON Timer RE (8 bits x 1)
Timer RF (16 bits x 1)
Port P8
LIN module
SCK System
INV Clock Zero Detect Power Supply
8
Error AMP Manager
4 ZEROL/NA 1 16 ZEROR/ZEROA Watchdog timer
MS 2 15 VOUTL (15 bits)
IC303: R1172S331B-E2-F IC304: LE24C023M-TLM-E IC306: BD5229G-TR
Port P9
MC 3 14 VOUTR
VCC
AGND
ZEROR/ZEROA(1)
(ZEROA)
ZEROL/NA(1)
SS CMOS-based positive-voltage regulator IC Two wire serial interface EEPROM Voltage detector IC with adjustable output delay A/D converter
4
MD 4 13 VCOM
(10 bits x 20 channels)
FIN
SCK 5 12 AGND VDD
WP Write controller High voltage generator
DATA 6 11 VCC 2
GND D/A converter R8C/Tiny Series microprocessor core Memory
BCK 7 10 NC VDD 6 1 VOUT SCL (8 bits x 2)
Input Buffer
(1) Open-drain output for thePCM1782 LRCK 8 9 NC

Condition detector
R0H R0L SB ROM(1)

Serial controller
1 Vout
10 NOTE: Signal names in parentheses ( ) are for the PCM1781.
Address generator
R1H R1L
X decoder
USP
EEPROM Array
R2
R3 ISP
– INTB RAM(2)
★ All voltages are measured with a 10MΩ/V DC electronic voltmeter. ● 電圧は、内部抵抗 10MΩの電圧計で測定したものです。 Vref Pin No. Symbol Description +
A0
A1
PC
★ Components having special characteristics are marked and must be replaced ● 印のある部品は、安全性確保部品を示しています。部品の交換が必要な場合、 Current Limit
1 VOUT Output Pin of Voltage Regulator
NC 1 8 VDD Vref
FB FLG
I/O Buffer
2, 5 GND Ground Pin Y decoder and Sense AMP Multiplier

with parts having specifications equal to those originally installed. パーツリストに記載されている部品を使用してください。 CE 3 2,5 GND NC 2 7 WP 4 NC
3 CE Chip Enable Pin
★ Schematic diagram is subject to change without notice. ● 本回路図は標準回路図です。改良のため予告なく変更することがございます。 4 NC No Connection SDA
Serial-Parallel converter
NC
GND
3
4
6
5
SCL
SDA NOTES:
6 VDD Input Pin 3 5
1. ROM size varies with MCU type.
GND CT 2. RAM size varies with MCU type.
42
CD-S300
OPERATION 1/3
1
OPERATION (1)
-21.7
3.4
-26.5
-26.5
-26.5
-26.4
0
0
3.2
3.3
3.3
3.2
3.3
-28.0
0
-3.4 3.4
-26.5 -26.5
3 -26.5 -26.4
-21.7
Page 45 M8
-21.7
-21.7
W702
3.3 W701A
W701B
0 3.3 3.3 3.3
3.3 0
3.3 3.3 3.3

POWER
3.4 3.3 indicator
5 0.3 0.3 1.9
3.4 PURE DIRECT
Page 42 G2
0 indicator
to MAIN_CB304
3.3 0
0 1.9 0
3.4
0 3.3
3.4
3.4
OPERATION (2)
3.4 0 0
3.4
0
6
CB701
OPERATION (3)
W703 CB753
0
0.3
Key detection for A/D port iPod/USB
Key input (A/D) pull-up resistance 10 k-ohms 0.3
Ohm 0 + 820 + 3.3 k + 12.0 k
V 0 0.2 – 0.3 0.9 – 1.0 2.0 – 2.1
CB752
A/D value (3.3V=255) 0 15 – 25 70 – 78 153 – 162
7 KEY0 (58 pin) – STOP PAUSE OPEN/CLOSE
KEY1 (59 pin) – PLAY SKIP +/SEARCH + SKIP -/SEARCH -
Ohm 0 + 100 + 3.3 k + 12.0 k

V 0 0.03 – 0.1 0.8 – 0.9 2.0 – 2.1
A/D value (3.3V=255) 0 3–7 60 – 70 150 – 160
KEY2 (60 pin) – PURE DIRECT CD/USB –
iPod/USB
indicator 0
3.3
3.3
0
0
3.3
IC702
3.3 3.3
0
0.2
0
0
8
W751
0
PURE
CD/USB
DIRECT
Page 41 M3
to MAIN_CB6
9
IC702: TC7SH08F
2-input AND gate
IN B 1 5 VCC
A B Y
IN A 2 L L L
L H L
GND 3 4 OUT Y H L L
H H H
10
★ All voltages are measured with a 10MΩ/V DC electronic voltmeter. ● 電圧は、内部抵抗 10MΩの電圧計で測定したものです。
★ Components having special characteristics are marked and must be replaced ● 印のある部品は、安全性確保部品を示しています。部品の交換が必要な場合、
43
CD-S300
OPERATION 2/3
1
0
CB901 3.3 3.3 3.3
2
0 0
0
Page 42 K2 3.3 0
Writing port
to MAIN_CB310
3.3 0
0
0 0
0
3.3
3
CB902
OPERATION (9)
3 dB AMP. L.P.F.
5
5.0
0
0
CB601
0 0
IC601 0
0 0 0
-5.0
-4.5 -4.5
CB601
6 -4.5 0 0
-5.0
5.0
2.5
Page 42 B7
to MAIN_CB303 0
ANALOG OUT OUTPUT
2.5
0
7
ANALOG OUT L
0 0
-5.0
-4.5 -4.5
5.0
0 0 0
0
IC602
0 0
IC602 0
8 0
OPERATION (4)
IC601, 602: NJM2068D-D
Dual operational amplifier
V+
8
OUT1 1 8 +VCC
2, 6 OUTPUT
–INPUT –IN1 2 7 OUT2
+INPUT 1, 7 + – + –
3, 5
+IN1 3 6 -IN2
10
–VCC 4 5 +IN2
★ All voltages are measured with a 10MΩ/V DC electronic voltmeter. ● 電圧は、内部抵抗 10MΩの電圧計で測定したものです。 V–
★ Components having special characteristics are marked and must be replaced ● 印のある部品は、安全性確保部品を示しています。部品の交換が必要な場合、 4
44
CD-S300
OPERATION 3/3
1
7.9
2 OPERATION (8) 12.0
12.0 7.9
-0.1 12.0
0
-0.1 12.0
5.0
12.0
CB806
0
12.1
OPERATION (6) 7.2
0
POWER ON/OFF
0
12.0 IC801
5.0
5.0
0 Page 42 B5
4 5.0 to MAIN_CB301
0
OPERATION (10) -5.0
-4.5
CB803
11.8 5.0
W806A
W806B
5 IC802
11.8 5.0
-0.1 12.0 0
5.0
AC21.2
-0.1 12.0
CB801 CB802 CB804 W807 0
-0.1
0
AC IN -0.1
0 -0.1 -13.9
0
-21.7
-21.7 -0.1 -13.9
0 -5.0
6 -13.9 -5.0
IC803
AC5.2
POWER
TRANSFORMER -13.9 -5.0
W801B
W802B
W805B
W803B
W804B
11.2
OPERATION (5) -0.1 11.9 11.9 7.4 7.4 -4.5
7 7.0
-0.1
11.9 0
W801A
W802A
W805A
W803A
W804A
-11.9 7.0
CB807
-40.7 -27.9 -27.9
-27.4 -40.7
-21.7
-27.4
VOLTAGE
-28.5 -21.7
8 SELECTOR
-27.9 0
-13.9
-28.5
-21.8
Page 43 B3
0 to OPERATION (1)_W702
OPERATION (7) R, L models
9
IC801, 802: KIA7805API IC803: KIA79M05PI-U
Voltage regulator Voltage regulator
1 INPUT -5V
R22 R17 R23
R1 Q11 Q11-1 R7
1.4K
Q15 Q8
Q16 R18 R19
Q12 Q7 4K 5K
Q14 R14
R10 R15
Q17 Q19 R16 R6
R19
7K Q10
R12 3 OUTPUT
Q18 R20 Q9
Q6 D1 D2
Q1 R5
R18 6.2V 6.2V R17
R11 15K Q11
R9 Q12 5.4K
Z1 R7 C1
R2 Q10 Q6 Q17
Q2
Q7 R21 Q2 VOUT
Q13 R3
Q16 Q18
10 R13
Q3
Q4
Q5 Q9 Q8
R10
3K R11
Q19
R15
D3
6.2V
10K
R4 R5 2K
R6 R8
2 COMMON (GND) Q1 Q13
R12 R14 R20 ★ All voltages are measured with a 10MΩ/V DC electronic voltmeter. ● 電圧は、内部抵抗 10MΩの電圧計で測定したものです。
10pF 20K
★ Components having special characteristics are marked
20pF 600 15K
Q3 Q4 Q5 R4
and must be replaced ● 印のある部品は、安全性確保部品を示しています。部品の交換が必要な場合、
20K Q14
R8 R9
Q15 Q20
R13 Q21 R21
R1
750
R2
1K
R3
6K
20K 20K 5K 150 R16
0.05 ★ Schematic diagram is subject to change without notice. ● 本回路図は標準回路図です。改良のため予告なく変更することがございます。
VIN
45
CD-S300
■ REPLACEMENT PARTS LIST

• ELECTRICAL COMPONENT PARTS
WARNING
● Components having special characteristics are marked and must be replaced with parts having specifications
equal to those originally installed.
● 印のある部分は、安全確保部品を示しています。部品の交換が必要な場合、パーツリストに記載されている部品を使用し
てください。
● 部品価格ランクは、予告なく変更することがあります。
ABBREVIATIONS IN THIS LIST ARE AS FOLLOWS:

C.A.EL.CHP : CHIP ALUMI.ELECTROLYTIC CAP L.EMIT : LIGHT EMITTING MODULE
C.CE : CERAMIC CAP LED.DSPLY : LED DISPLAY
C.CE.ARRAY : CERAMIC CAP ARRAY LED.INFRD : LED,INFRARED
C.CE.CHP : CHIP CERAMIC CAP MODUL.RF : MODULATOR,RF
C.CE.ML : MULTILAYER CERAMIC CAP PHOT.CPL : PHOTO COUPLER
C.CE.M.CHP : CHIP MULTILAYER CERAMIC CAP PHOT.INTR : PHOTO INTERRUPTER
C.CE.SAFTY : RECOGNIZED CERAMIC CAP PHOT.RFLCT : PHOTO REFLECTOR
C.CE.TUBLR : CERAMIC TUBULAR CAP PIN.TEST : PIN,TEST POINT
C.CE.SMI : SEMI CONDUCTIVE CERAMIC CAP PLST.RIVET : PLASTIC RIVET
C.EL : ELECTROLYTIC CAP R.ARRAY : RESISTOR ARRAY
C.MICA : MICA CAP R.CAR. : CARBON RESISTOR
C.ML.FLM : MULTILAYER FILM CAP R.CAR.CHP : CHIP RESISTOR
C.MP : METALLIZED PAPER CAP R.CAR.FP : FLAME PROOF CARBON RESISTOR
C.MYLAR : MYLAR FILM CAP R.FUS : FUSABLE RESISTOR
C.MYLAR.ML : MULTILAYER MYLAR FILM CAP R.MTL.CHP : CHIP METAL FILM RESISTOR
C.PAPER : PAPER CAPACITOR R.MTL.FLM : METAL FILM RESISTOR
C.PLS : POLYSTYRENE FILM CAP R.MTL.OXD : METAL OXIDE FILM RESISTOR
C.POL : POLYESTER FILM CAP R.MTL.PLAT : METAL PLATE RESISTOR
C.POLY : POLYETHYLENE FILM CAP RSNR.CE : CERAMIC RESONATOR
C.PP : POLYPROPYLENE FILM CAP RSNR.CRYS : CRYSTAL RESONATOR
C.TNTL : TANTALUM CAP R.TW.CEM : TWIN CEMENT FIXED RESISTOR
C.TNTL.CHP : CHIP TANTALUM CAP R.CEMENT : CEMENT RESISTOR
C.TRIM : TRIMMER CAP SCR.BND.HD : BIND HEAD B-TIGHT SCREW
CN : CONNECTOR SCR.BW.HD : BW HEAD TAPPING SCREW
CD-S300
CN.BS.PIN : CONNECTOR,BASE PIN SCR.CUP : CUP TIGHT SCREW
CN.CANNON : CONNECTOR,CANNON SCR.TERM : SCREW TERMINAL
CN.DIN : CONNECTOR,DIN SCR.TR : SCREW,TRANSISTOR
CN.FLAT : CONNECTOR,FLAT CABLE SUPRT.PCB : SUPPORT,P.C.B.
CN.POST : CONNECTOR,BASE POST SURG.PRTCT : SURGE PROTECTOR
COIL.MX.AM : COIL,AM MIX SW.TACT : TACT SWITCH
COIL.AT.FM : COIL,FM ANTENNA SW.LEAF : LEAF SWITCH
COIL.DT.FM : COIL,FM DETECT SW.LEVER : LEVER SWITCH
COIL.MX.FM : COIL,FM MIX SW.MICRO : MICRO SWITCH
COIL,OUTPT : OUTPUT COIL SW.PUSH : PUSH SWITCH
DIOD.ARRAY : DIODE ARRAY SW.RT.ENC : ROTARY ENCODER
DIODE.BRG : DIODE BRIDGE SW.RT.MTR : ROTARY SWITCH WITH MOTOR
DIODE.CHP : CHIP DIODE SW.RT : ROTARY SWITCH
DIODE.VAR : VARACTOR DIODE SW.SLIDE : SLIDE SWITCH
DIOD.Z.CHP : CHIP ZENER DIODE TERM.SP : SPEAKER TERMINAL
DIODE.ZENR : ZENER DIODE TERM.WRAP : WRAPPING TERMINAL
DSCR.CE : CERAMIC DISCRIMINATOR THRMST.CHP : CHIP THERMISTOR
FER.BEAD : FERRITE BEADS TR.CHP : CHIP TRANSISTOR
FER.CORE : FERRITE CORE TR.DGT : DIGITAL TRANSISTOR
FET.CHP : CHIP FET TR.DGT.CHP : CHIP DIGITAL TRANSISTOR
FL.DSPLY : FLUORESCENT DISPLAY TRANS : TRANSFORMER
FLTR.CE : CERAMIC FILTER TRANS.PULS : PULSE TRANSFORMER
FLTR.COMB : COMB FILTER MODULE TRANS.PWR : POWER TRANSFORMER ASS’Y
FLTR.LC.RF : LC FILTER,EMI TUNER.AM : TUNER PACK,AM
GND.MTL : GROUND PLATE TUNER.FM : TUNER PACK,FM
GND.TERM : GROUND TERMINAL TUNER.PK : FRONT-ENDTUNER PACK
HOLDER.FUS : FUSE HOLDER VR : ROTARY POTENTIOMETER
IC.PRTCT : IC PROTECTOR VR.MTR : POTENTIOMETER WITH MOTOR
JUMPER.CN : JUMPER CONNECTOR VR.SW : POTENTIOMETER WITH ROTARY SW
JUMPER.TST : JUMPER,TEST POINT VR.SLIDE : SLIDE POTENTIOMETER
L.DTCT : LIGHT DETECTING MODULE VR.TRIM : TRIMMER POTENTIOMETER
47
CD-S300
P.C.B. MAIN
Ref No. Part No. Description Remarks Markets 部品名ランク
* WS176200 P.C.B. MAIN ＰＣＢＭＡＩＮ
CB1 WQ289300 CN 24P TE ＦＦＣ/ＦＰＣコネクタ 04
CB2 VB390100 CN.BS.PIN 5P ベースピン 01
CB3 VB390200 CN.BS.PIN 6P コネクタベースポスト 01
CB301 VK217300 CN 10P ＦＪリセプタクル 01
CB303 VQ962800 CN.BS.PIN 7P ウエハー 02
CB304 VM859600 CN.BS.PIN 15P ＦＦＣコネクター 01
CB310 VP768200 CN 5P ＦＪリセプタクル 01
C1-2 US135100 C.CE.CHP 0.1uF 16V チップセラコン 01
C3-5 UF437470 C.EL.CHP 47uF 16V チップケミコン 01
C10 US135100 C.CE.CHP 0.1uF 16V チップセラコン 01
C11 UF437470 C.EL.CHP 47uF 16V チップケミコン 01
C13 WC892500 C.EL.CHP 470uF 16V チップケミコン 01
C16 US163100 C.CE.CHP 1000pF 50V チップセラコン 01
C20 WC666800 C.CE.CHP 1uF 16V チップセラコン 01
C21 US063470 C.CE.CHP 4700pF 50V B チップセラコン 01
C25 US064100 C.CE.CHP 0.01uF 50V B チップセラコン 01
C31 WC890400 C.EL.CHP 100uF 6.3V チップケミコン 01
CD-S300
C32-33 US062470 C.CE.CHP 470pF 50V B チップセラコン 01

C43 UF418100 C.EL.CHP 100uF 6.3V チップケミコン 01
* C44 WP882000 C.CE.CHP 10uF 6.3V チップセラコン
C58-59 UF418100 C.EL.CHP 100uF 6.3V チップケミコン 01
C72 WJ881200 C.CE.CHP 1uF 16V チップセラコン 01
C73 WC890400 C.EL.CHP 100uF 6.3V チップケミコン 01
C76 WJ881200 C.CE.CHP 1uF 16V チップセラコン 01
✻ New Parts ＊新規部品
48
CD-S300
P.C.B. MAIN
C77 WG251600 C.CE.CHP 4.7uF 6.3V チップセラコン 01
C79 WP258700 C.CE.CHP 2.2uF 25V チップセラコン 01
C302 UR249100 C.EL 1000uF 25V ケミコン 01
C303 WF547900 C.CE.CHP 10uF 25V チップセラコン 01
C305 WF547900 C.CE.CHP 10uF 25V チップセラコン 01
* C312 WC891800 C.EL.CHP 10uF 16V チップケミコン
C313 WC892500 C.EL.CHP 470uF 16V チップケミコン 01
C314 WK004400 C.CE.M.CHP 10uF 16V チップ積層セラコン 01
* C319 WP882000 C.CE.CHP 10uF 6.3V チップセラコン
* C359 UF417470 C.EL.CHP 47uF 6.3V チップケミコン
CD-S300
C360 WC666800 C.CE.CHP 1uF 16V チップセラコン 01
* C361 UF417470 C.EL.CHP 47uF 6.3V チップケミコン
D1 VT332900 DIODE 1SS355 ダイオード 01
D2 VV220700 DIODE.SHOT RB501V-40 ショットキーダイオード 01
D6 VV220700 DIODE.SHOT RB501V-40 ショットキーダイオード 01
D301-302 VV220700 DIODE.SHOT RB501V-40 ショットキーダイオード 01
D303-305 VT332900 DIODE 1SS355 ダイオード 01
* D308 WP292300 DIODE RB050LA-40TR TP ダイオード
F301 WH983200 SW.POLY MINISMDC110F/24-2 ポリスィッチ 02
* IC1 YA727A00 IC LA6565 ドライバーＩＣ
* IC2 YA748A00 IC.CD LC786922 (MASKROM) ＩＣ
IC4 XR680A00 IC TC7SH08FU(TE85L,JF) ロジックＩＣ 01
IC6 X8096A00 IC R5523N001A-TR-F 電源ＩＣ 03
* IC7 YA724A00 IC.USB LC87F1HC8A (written) ＩＣ
IC301 X9850A00 IC BD9870FPS 電源ＩＣ 05
IC302 X7356A00 IC PCM1780DBQR ＩＣ 04
IC303 X8897A00 IC R1172S331B-E2-F 電源ＩＣ 03
* IC304 YA765A00 IC LE24C023M ＩＣ
* IC305 YA749A00 IC.CPU R5F212CASNFP CPU (unwritten) ＣＰＵＩＣ
49
CD-S300
P.C.B. MAIN and P.C.B. OPERATION

IC306 YA514A00 IC BD5229G-TR リセットＩＣ 01
PJ301 V2283400 JACK.PIN 1P ピンジャック 04
* Q1 WS074200 TR 12A01C PNP トランジスタ
Q301 VV556500 TR 2SA1037K Q,R,S トランジスタ 01
Q304 VV556400 TR 2SC2412K Q,R,S トランジスタ 01
Q309 VV655700 TR.DGT DTC144EKA デジタルトランジスタ 01
U301 WH536900 CN.PHOTO.T 1P GP1FAV51TK0F 光ファイバー送信器 04
XL1 WB872100 RSNR.CRYS 16.9344MHz 水晶振動子 03
XL2 WG538400 RSNR.CRYS 12MHz 水晶振動子
XL301 V8222200 RSNR.CE 10MHz CSTLS10M0 セラミック振動子 01
* WS176300 P.C.B. OPERATION J ＰＣＢＯＰＥＲＡＴＩＯＮ

* WS176400 P.C.B. OPERATION RL ＰＣＢＯＰＥＲＡＴＩＯＮ
* WS176500 P.C.B. OPERATION T ＰＣＢＯＰＥＲＡＴＩＯＮ
* WS176600 P.C.B. OPERATION A ＰＣＢＯＰＥＲＡＴＩＯＮ
* WS176700 P.C.B. OPERATION G ＰＣＢＯＰＥＲＡＴＩＯＮ
CB601 VQ961000 CN.BS.PIN 7P ハウジング 02
CB701 VM929900 CN.BS.PIN 15P ＦＰＣコネクター 01
CB752 WP170400 CN.USB CSS5004-1F01 4P TE ＵＳＢコネクタ 04
CB801-802 WN103000 CLIP.FUSE TP00351-31 ヒューズクリップ 01
CB803 VP245700 CN.BS.PIN VA 2P SE ベースツキポスト 01
CB804 LB918060 CN.BS.PIN 6P ベース付ポスト 01
CB806 VK216500 CN 10P ＦＪ－Ｌプラグ 02
CB901 VP768100 CN.BS.PIN 5P ＦＪコネクタープラグ 01
CD-S300
CB902 VQ044400 CN.BS.PIN 9P ＦＦＣコネクター 01

C601-602 UU237470 C.EL 47uF 16V ケミコンＦＷ 01
C603-604 WE100900 C.PP 220pF 630V ＰＰコン 02
* C605-606 WJ609300 C.MYLAR 2200pF 100V マイラーコン
* C607-608 WJ609800 C.MYLAR 5600pF 100V マイラーコン
C609-610 UU238100 C.EL 100uF 16V ケミコン 01
C611-612 WQ331800 C.EL 100uF 50V ケミコン 01
C614-615 WJ608900 C.MYLAR 1000pF 100V マイラーコン 01
C701-702 US064100 C.CE.CHP 0.01uF 50V B チップセラコン 01
C707 WG780700 C.EL 47uF 16V ケミコン 01
C709-712 US064100 C.CE.CHP 0.01uF 50V B チップセラコン 01
C714 WF752900 C.CE.M.CHP 1uF 50V Z チップ積層セラコン 01
C719 WG780700 C.EL 47uF 16V ケミコン 01
C801-802 V6185300 C.CE.SAFTY 0.01uF 275V 規格認定コンデンサ 01
C805 V6185300 C.CE.SAFTY 0.01uF 275V 規格認定コンデンサ 01
C807 UR267470 C.EL 47uF 50V ケミコン 01
C808-809 WE102900 C.PP 0.01uF 100V ＰＰコン
C810 UR278100 C.EL 100uF 63V ケミコン 01
C811 UR267220 C.EL 22uF 50V ケミコン 01
50
CD-S300
P.C.B. OPERATION
C812 UR267470 C.EL 47uF 50V ケミコン 01
C813 UR04A100 C.EL 10000uF 25V ケミコン 07
C814-815 UR267220 C.EL 22uF 50V ケミコン 01
C816 WQ785400 C.EL 6800uF 25V ケミコン
C817 UR249100 C.EL 1000uF 25V ケミコン 01
C818 WJ608900 C.MYLAR 1000pF 100V マイラーコン 01
C819 UR248100 C.EL 100uF 25V ケミコン
C820-822 WN165300 C.PP 0.01uF 100V ＰＰコン 01
C823 UR239100 C.EL 1000uF 16V ケミコン
C824 UR266330 C.EL 3.3uF 50V ケミコン
C825-827 WN165300 C.PP 0.01uF 100V ＰＰコン 01
C828-831 UR248100 C.EL 100uF 25V ケミコン
C832-833 UR267220 C.EL 22uF 50V ケミコン 01
C834 WE102900 C.PP 0.01uF 100V ＰＰコン 01
D702-703 WA467800 LED SEL6910A-CD ＬＥＤ 01
D751 WP947300 LED ORANGE/GREEN ２色ＬＥＤ 01
D752 VG437700 DIODE.ZENR MTZJ5.6B 5.6V ツェナーダイオード 01
D801-802 VS997800 DIODE 1T2 ダイオード 01
D803-804 VV731400 DIODE 2A02M ダイオード 01
D805-810 VS997800 DIODE 1T2 ダイオード 01
D811 VG443200 DIODE.ZENR MTZJ30A 30V ツェナーダイオード 01
D816 VG438800 DIODE.ZENR MTZJ8.2A 8.2V ツェナーダイオード 01
CD-S300
D820-821 VV220700 DIODE.SHOT RB501V-40 ショットキーダイオード 01
F801 KB000710 FUSE 500mA 250V ヒューズ２５０Ｖ 02
IC601-602 XA987A00 IC NJM2068D-D ＩＣ 01
IC702 X2656A00 IC TC7SH08F AND ロジックＩＣ 01
IC801-802 X4928A00 IC KIA7805API 5V 電源ＩＣ 02
IC803 X7973A00 IC KIA79M05PI-U 電源ＩＣ 02
* PJ601 WS071500 JACK.PIN 2P YKC21-4122V ピンジャック
Q601-604 VZ725900 TR 2SD1938F S,T トランジスタ 01
Q702 VV655000 TR.DGT DTA114EKA デジタルトランジスタ 01
Q703-704 VV655400 TR.DGT DTC114EKA デジタルトランジスタ 01
Q706 VV655000 TR.DGT DTA114EKA デジタルトランジスタ 01
Q801 VP872600 TR 2SA1708 S,T トランジスタ 01
Q804 VS883400 TR 2SD2394 E,F トランジスタ 02
Q806 VV556500 TR 2SA1037K Q,R,S トランジスタ 01
Q901 VV655400 TR.DGT DTC114EKA デジタルトランジスタ 01
R653-654 WQ835800 R.MTL.OXD 100Ω 1W 酸化金属被膜抵抗
R801 HV756470 R.CAR.FP 4.7KΩ 1/4W 不燃化カーボン抵抗 01
* R802 HL006470 R.MTL.OXD 4.7KΩ 1/2W 酸化金属被膜抵抗
R805 V8071600 R.MTL.FLM 1KΩ 1W 金属被膜抵抗 01
R806 V8071300 R.MTL.FLM 470Ω 1W 金属被膜抵抗
R808 HV755330 R.CAR.FP 330Ω 1/4W 不燃化カーボン抵抗 01
R813-814 HV755100 R.CAR.FP 100Ω 1/4W 不燃化カーボン抵抗 01
R815-816 HV753470 R.CAR.FP 4.7Ω 1/4W 不燃化カーボン抵抗 01
ST601 WA246200 SCR.TERM 3.5 スクリューターミナル
ST701 V4040500 SCR.TERM M3 スクリューターミナル 01
ST751 V4040500 SCR.TERM M3 スクリューターミナル 01
51
CD-S300
P.C.B. OPERATION
ST801-802 V4040500 SCR.TERM M3 RL スクリューターミナル 01
ST901-902 V4040500 SCR.TERM M3 スクリューターミナル 01
SW701-708 WD483100 SW.TACT SKRGAAD010 タクトＳＷ 01
SW801 V8377400 SW.POWER SY16-52-4 パワースィッチ
SW802 WH813600 VOLT.SELCT VSA-14-3 RL 電圧切替器
* T801 YA770A00 TRANS.PWR J 電源トランス
* T801 YA772A00 TRANS.PWR RL 電源トランス
* T801 YA773A00 TRANS.PWR T 電源トランス
* T801 YA775A00 TRANS.PWR A 電源トランス
* T801 YA774A00 TRANS.PWR G 電源トランス
* TE801 WS090800 INLET.AC 2P HJC-036P ＡＣインレット
TH801-802 VU847300 POSISTOR RUE185 1.85A 30V ポリスイッチ 03
TH803 VV457600 SW.POLY RUE090 0.90A 30V ポリスイッチ 02
U701 WK918500 L.DTCT GP1UE271RKVF リモコン受光ユニット 03
* V701 WR861000 FL.DSPLY 14-ST-68GINK 螢光表示管
* WS050700 SHEET.FL 118x20.5 ＦＬシート
V6203300 SPACER.FL スペーサーＦＬ 01
WE983600 SCR.BND.HD 3x8 MFZN2B3 バインド小ネジ 01
CD-S300

52
CD-S300
Carbon Resistors
Value 1/4W Type Part No. 1/6W Type Part No. Value 1/4W Type Part No. 1/6W Type Part No.
1.0 Ω HJ35 3100 HF85 3100 11 kΩ HF45 7110 HF45 7110
1.8 Ω HJ35 3180 ✻ 12 kΩ HJ35 7120 HF85 7120
2.2 Ω HJ35 3220 HF85 3220 13 kΩ HF45 7130 HF45 7130
3.3 Ω HJ35 3330 HF85 3330 15 kΩ HF45 7150 HF45 7150
4.7 Ω HJ35 3470 HF85 3470 18 kΩ HF45 7180 HF45 7180
5.6 Ω HJ35 3560 HF85 3560 22 kΩ HF45 7220 HF45 7220
10 Ω HF45 4100 HF45 4100 24 kΩ HF45 7240 HF45 7240
15 Ω HJ35 4150 HF85 4150 27 kΩ HJ35 7270 HF85 7270
22 Ω HF45 4220 HF45 4220 30 kΩ HF45 7300 HF45 7300
27 Ω HJ35 4270 HF85 4270 33 kΩ HF45 7330 HF45 7330
33 Ω HF45 4330 HF45 4330 36 kΩ HF45 7360 HF45 7360
39 Ω HJ35 4470 HF85 4390 39 kΩ HF45 7390 HF45 7390
47 Ω HF45 4470 HF45 4470 47 kΩ HF45 7470 HF45 7470
56 Ω HF45 4560 HF45 4560 51 kΩ HF45 7510 HF45 7510
68 Ω HF45 4680 HF45 4680 56 kΩ HF45 7560 HF45 7560
75 Ω HF45 4750 HF45 4750 62 kΩ HF45 7620 HF45 7620
82 Ω HF45 4820 HF45 4820 68 kΩ HF45 7680 HF45 7680
91 Ω HF45 4910 HF45 4910 82 kΩ HF45 7820 HF45 7820
100 Ω HF45 5100 HF45 5100 91 kΩ HF45 7910 HF45 7910
110 Ω HJ35 5110 HF85 5110 100 kΩ HF45 8100 HF45 8100
120 Ω HF45 5120 HF45 5120 110 kΩ HF45 8110 HF45 8110
150 Ω HF45 5150 HF45 5150 120 kΩ HF45 8120 HF45 8120
160 Ω HJ35 5160 ✻ 130 kΩ HF45 8130 ✻
180 Ω HF45 5180 HF45 5180 150 kΩ HF45 8150 HF45 8150
200 Ω HF45 5200 HF45 5200 180 kΩ HF45 8180 HF45 8180
220 Ω HF45 5220 HF45 5220 220 kΩ HJ35 8220 HF85 8220
270 Ω HF45 5270 HF45 5270 270 kΩ HF45 8270 HF45 8270
330 Ω HF45 5330 HF45 5330 300 kΩ HF45 8300 HF45 8300
390 Ω HF45 5390 HF45 5390 330 kΩ HF45 8330 HF45 8330
430 Ω HF45 5430 HF45 5430 390 kΩ HJ35 8390 HF85 8390
470 Ω HF45 5470 HF45 5470 470 kΩ HF45 8470 HF45 8470
510 Ω HF45 5510 HF45 5510 560 kΩ HJ35 8560 HF85 8560
560 Ω HF45 5560 HF45 5560 680 kΩ HJ35 8680 HF85 8680
680 Ω HF45 5680 HF45 5680 820 kΩ HJ35 8820 HF85 8820
820 Ω HF45 5820 HF45 5820 1.0 MΩ HF45 9100 HF45 9100
910 Ω HF45 5910 HF45 5910 1.2 MΩ HJ35 9120 ✻
1.0 kΩ HF45 6100 HF45 6100 1.5 MΩ HJ35 9150 HF85 9150
1.2 kΩ HF45 6120 HF45 6120 1.8 MΩ HJ35 9180 HF85 9180
1.5 kΩ HF45 6150 HF45 6150 2.2 MΩ HJ35 9220 HF85 9220
1.8 kΩ HF45 6180 HF45 6180 3.3 MΩ HJ35 9330 HF85 9330
2.0 kΩ HJ35 6200 HF85 6200 3.9 MΩ HJ35 9390 ✻
2.2 kΩ HF45 6220 HF45 6220 4.7 MΩ HJ35 9470 HF85 9470
2.4 kΩ HJ35 6240 HF85 6240
2.7 kΩ HF45 6270 HF45 6270
3.0 kΩ HF45 6300 HF45 6300
1/4W Type
3.3 kΩ HF45 6330 HF45 6330
HF45
3.6 kΩ HJ35 6360 HF85 6360
1/4W Type 1/6W Type
3.9 kΩ HF45 6390 HF45 6390 HJ35 HF85
4.7 kΩ HF45 6470 HF45 6470 10mm
5mm
5.1 kΩ HF45 6510 HF45 6510
5.6 kΩ HF45 6560 HF45 6560
6.8 kΩ HF45 6680 HF45 6680
8.2 kΩ HF45 6820 HF45 6820
9.1 kΩ HF45 6910 HF45 6910
10 kΩ HF45 7100 HF45 7100
❊ : Not available
53
A B C D E F G H I J
CD-S300
• OVERALL ASS'Y R, L models

165
162 101 166

163 6 (5)
165
166
2 6 (7)
166
165
154 103
31 6 (9) 166
165 166
166
166
22
150
3 152 166
153 166
6 (6) 165
1-25
40
165
162
6 (2) 1-25
1-16
33
4
167 5 165
1-18 6 (4)
1-25
165 6 (3) 167
6 (10) 150
6 (1) 200
1-3 156
1-11 1-15 151
1-17
6 (8)
5
1-17
167 200-1
1-25
202
6 1-14
1-25
120
166 165
165
203
164
1-25 120
7
155
165
54
CD-S300
Ref No. Part No. Description Remarks Markets 部品名ランク Ref No. Part No. Description Remarks Markets 部品名ランク
1-3 MF115200 FLEXIBLE FLAT CABLE 15P 200mm P=1.25 カード電線 02 * 203 WS184100 POWER CABLE 1.5m 1pc A 電源コード
* 1-11 WR787900 FRONT PANEL BL フロントパネル * 203 WS171200 POWER CABLE 1.5m 1pc GL 電源コード
* 1-11 WR787700 FRONT PANEL SI フロントパネル BATTERY R6,AA,UM-3 2pcs 単３乾電池
* 1-14 WR791700 WINDOW PANEL LID ウインドウ
* 1-15 WR788500 SUB PANEL BL サブパネル SERVICE TOOL
* 1-15 WR788400 SUB PANEL SI サブパネル WR492800 RS232C CONVERSION ADAPTOR 3.3Vtype with FFC9P ＲＳ２３２Ｃ変換アダプタ
1-16 WQ433100 CAP POWER ON/OFF BL キャップ 03
1-16 WQ433000 CAP POWER ON/OFF SI キャップ 04
1-17 WP080600 LENS LED レンズＬＥＤ 01
* 1-18 WS217600 BARRIER バリアー
1-25 WE774800 BIND HEAD P-TIGHT SCREW 3x8 MFZN2W3 バインドＰタイトネジ 01
* 5 WS176200 P.C.B. ASS'Y MAIN ＰＣＢＭＡＩＮ
* 6 WS176300 P.C.B. ASS'Y OPERATION J ＰＣＢＯＰＥＲＡＴＩＯＮ
* 6 WS176400 P.C.B. ASS'Y OPERATION RL ＰＣＢＯＰＥＲＡＴＩＯＮ
* 6 WS176500 P.C.B. ASS'Y OPERATION T ＰＣＢＯＰＥＲＡＴＩＯＮ
* 6 WS176600 P.C.B. ASS'Y OPERATION A ＰＣＢＯＰＥＲＡＴＩＯＮ
* 6 WS176700 P.C.B. ASS'Y OPERATION G ＰＣＢＯＰＥＲＡＴＩＯＮ
22 WK899500 FLEXIBLE FLAT CABLE 24P 240mm P=0.5 カード電線 01
* 31 WU088700 LOADER MECHANISM UNIT ローダーメカユニット
33 WR513400 SCREW LOADER MFZN2W3 ローダースクリュー 01
* 40 WR788300 LID BL リッド
* 40 WR788200 LID SI リッド
101 WF481100 TOP COVER BL トップカバー 08
* 101 WS325300 TOP COVER SI トップカバー
* 103 WR788800 REAR PANEL J リアパネル
* 103 WR789500 REAR PANEL R リアパネル
* 103 WR789300 REAR PANEL T リアパネル
* 103 WR788900 REAR PANEL A リアパネル
* 103 WR789000 REAR PANEL G リアパネル
* 103 WR789200 REAR PANEL L リアパネル
120 VQ982800 LEG D60xH16 レッグ 01
150 VQ861500 CUSHION SHEET クッションシート 01
151 VG854200 SPACER PCB KGLS-10RT ロッキングカ－ドスペ－サ 01
* 152 WT769600 DAMPER 70x70x2 ダンパー
155 WC879000 DAMPER SCREW MASK ダンパー
156 VQ368600 PUSH RIVET P3555-B プッシュリベット 01
162 VH313200 PW HEAD S-TIGHT SCREW 4x8-10 MFNI3BL BL ＰＷヘッドＳタイトネジ 01
162 VD069600 PW HEAD S-TIGHT SCREW 4x8-10 MFNI33 SI ＰＷヘッドＳタイトネジ 01
163 WF821300 BIND HEAD S-TIGHT SCREW 4x7 MFZN2W3 バインドＳタイトネジ 01
164 WF787100 BIND HEAD BONDING B-T. SCREW 3x12 MFZN2B3 ボンディングＢタイトネジ 01
165 WE774300 BIND HEAD B-TIGHT SCREW 3x8 MFZN2W3 バインドＢタイトネジ 01
166 WE774100 BIND HEAD BONDING B-T. SCREW 3x8 MFZN2B3 ボンディングＢタイトネジ 01
167 WE877900 BIND HEAD S-TIGHT SCREW 3x6 MFZN2W3 バインドＳタイトネジ 01
ACCESSORIES 付属品
* 200 WR960800 REMOTE CONTROL CDX8 リモコン
* 200-1 WT816600 BATTERY COVER dark gray 60050010 電池蓋
202 VY952200 RCA STEREO CABLE 2P 1m 1pc ステレオピンケーブル 04
* 203 WS184300 POWER CABLE 1.5m 1pc J 電源コード
* 203 WS171100 POWER CABLE 1.5m 1pc R 電源コード
* 203 WS184400 POWER CABLE 1.5m 1pc T 電源コード
✻ New Parts ＊新規部品 ✻ New Parts ＊新規部品
55
A B C D E F G H I J
CD-S300
1 ■ REMOTE CONTROL
SCHEMATIC DIAGRAM PANEL KEY LAYOUT KEY CODE
VCC Key Customer
Function Data Code
No. Code
2 CD/USB 79 6F
3 PURE DIRECT 79 6E
R1
3.3 ohms
2 2 3 4 4 OPEN/CLOSE 79 01
8 16
5 PROGRAM 79 0C
5 6 7
6 REPEAT 79 08
7 15 23 31
IR-LED 8 9 10 7 RANDOM 79 1B
IR1 U1
6 14 22 30 8 DIMMER 79 54
1 20
PA6 PA5 11 12 13 9 A/B 79 09
5 13 21 29 37
2 19 10 DISPLAY 79 0A
PA7 PA4 14 15 16
3
C1 11 1 79 11
47 uF/
4 12 20
10 V 3 18
+ PB0 PA3 17 18 19 12 2 79 12
3 11 19 27 35 13 3 79 13
4 17
PB1 PA2 20 21 22
Q1 14 4 79 14
TRKTC8050S 2 10 18
R2 5 16 15 5 79 15
TD PA1 23 25
VCC 220 ohms
16 6 79 16
9 17 25 33
6 15
VDD PA0 17 7 79 17
4 27
C4
0.1 uF
18 8 79 18
C2 7 14
XI PB6 29 30 31
15 pF 19 9 79 19
X1
C3 4 MHz
8 13 20 0 79 10
XO PB5 33
15 pF
21 ENTER 79 3F
9 12
GND PB4 22 CLEAR 79 0D
35 37
23 79 05
10 11
PB2_VPP PB3
5 25 79 06
JT7060-36 27 79 55
or
RT82P01-JT006
29 79 04
30 79 02
31 79 07
33 79 56
35 FOLDER 79 6A
6
37 FOLDER 79 69
56
CD-S300
MEMO
CD-S300
57
CD-S300

Yamaha CD-S300 Service Manual

Uploaded by

Copyright:

Available Formats

Yamaha CD-S300 Service Manual

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Yamaha CD-S300 Service Manual

Uploaded by

Copyright:

Available Formats

COMPACT DISC PLAYER

CD-S300 SERVICE MANUAL

Copyright © 2009 All rights reserved.

WARNING: CHEMICAL CONTENT NOTICE!

About lead free solder / 無鉛ハンダについて

WARNING: Laser Safety

Laser Emitting conditions:

Laser Diode Properties

Warning for power supply

■ PREVENTION OF ELECTROSTATIC DISCHARGE

Grounding for electrostatic breakdown prevention

Anti-static wrist strap

■ REMOTE CONTROL PANEL

Output Level / 出力レベル (1 kHz, 0 dB)

Other Output Terminal / その他の出力端子

Power Consumption / 消費電力

Power Supply / 電源電圧

J model .............................................................. AC 100 V, 50/60 Hz

Accessories / 付属品 Unit: mm (inch)

Battery (R6, AA, UM-3) .................................................................x 2

* Specifications are subject to change without notice due to

R ....................General model G .................European model

1 2 3 4 5 1 OPERATION (7) P.C.B. (R, L models)

■ DISASSEMBLY PROCEDURES / 分解手順

1. Removal of Top Cover 1. トップカバーの外し方

OPERATION (6) P.C.B. 2

Front panel ass'y

2. Removal of Front Panel Ass’y 2. フロントパネル ASSY の外し方

3. Removal of Loader Mechanism Unit 3. ローダーメカユニットの外し方

6 Loader mechanism unit 17 mm

CB3 Use a clip or other item to

When checking the P.C.B.s: P.C.B. をチェックする場合には：

Rubber sheet and cloth

■ TEST MODE / テストモード

iPod/USB indicator FL display

Power indicator PURE DIRECT indicator

" " (Power) switch

Release the keys

All segments OFF

2. While keep pressing those 3 keys, check that all 2. 3 つのキーを押したまま、全てのインジケーター

● Operation Procedure of Test Mode ● テストモード時の操作

Function list of remote control keys / リモコンキーの機能一覧

OPEN/CLOSE 79-01 Disc tray open/close / ディスクトレイ オープン／クローズ

1 79-11 Laser on / レーザー オン

2 79-12 Laser off / レーザー オフ

3 79-13 Focus operation / フォーカス動作

Traverse in * Press the “5” key to stop traverse.

5 79-15 Traverse stop / トラバース ストップ

Traverse out * Press the “5” key to stop traverse.

Spindle reverse * Press the “8” key to stop spindle.

8 79-18 Spindle off / スピンドル オフ

* Press the “8” key to stop spindle.

● Canceling Test Mode ● テストモードの解除

Display provided when factory mode started / ファクトリーモード起動時の表示

FACTORY LOADING NO DISC

● Operation Procedure of Factory Mode ● ファクトリーモード時の操作

Key Key code Function

● Canceling Factory Mode ● ファクトリーモードの起動

■ UPDATING FIRMWARE / ファームウェアの書き込み

OPEN/CLOSE 79-01 Disc tray open/close / ディスクトレイオープン／クローズ

1 79-11 Laser on / レーザーオン

2 79-12 Laser off / レーザーオフ

5 79-15 Traverse stop / トラバースストップ

8 79-18 Spindle off / スピンドルオフ