How To Read A Pump Curve

How to Read a Pump Curve
Years ago, making a pump selection meant sitting down with large printed catalogs and
flipping through them until you reached a pump curve that fit a project’s hydraulic
requirements. Today this process is made much easier through the use of electronic
pump curve catalogs. One of the most well-known developers of electronic pump
catalogs is Engineered Software and their pump selection software pump-flo. Another
popular option for pump selection software is Intelliquip.
All of the curves in this article were generated by Pump-Flo’s web-based pump
selection software.
This article is part of Pumps 101, an eleven-part series of articles designed as an

introduction to the fundamentals of centrifugal pump design, selection, and application.
To get the most out of Intro to Pumps check out the full series:
1. What is a Centrifugal Pump
2. Volutes, Casings, and Impellers
3. Parts of a Centrifugal Pump
4. Centrifugal Pump Designs
5. How to Read a Pump Curve
6. How to Make a Pump Selection
7. Understanding NPSH
8. How to Size an Electric Motor
9. Using a Pump with a VFD
10. Materials of Construction
11. Pump System Installation
What is a Pump Curve?

A pump curve is a graphical representation of the performance characteristics of
a pump.
A pump curve provides a wealth of information regarding the performance capabilities of
a pump. Information is plotted on an x-y graph where the x-axis is measured in units of
flow and the y-axis is measured in units of head, power, and NPSHr.
For the sake of example, today we’re going to look at a selection made for the following
design condition: 1,000 GPM at 100 ft.
Here is one possible pump selection that might be a good fit for that operating condition:
Comp
osite Pump Performance Curve
Head & Flow

The first piece of information provided by a pump curve is the flow that the pump will
develop at any given operating head. The curve that provides this information is called
the pump performance curve. Some pump curves only provide a single pump
performance curve, but most will provide the maximum performance the pump is
capable of achieving with a full-trim impeller, the minimum performance the pump is
capable of achieving with a minimum-trim impeller, and the performance provided by
the design-trim impeller.
The design-trim impeller is the
impeller trim the pump
selection software has selected
as the closest fit to the design
condition provided. In this
case, the design-trim is
16.3125”, the max-trim is 17”
and the minimum-trim is 15”.
We know this by looking at the
left-hand side of the curve
where these three numbers
appear.
Pump Performance Curve
Considering the design trim curve we see that at zero flow, also known as shutoff or
dead-head, the pump will develop about 130 ft of head. This is the head the pump
would develop if it were operating against a closed valve.
Keep in mind that the actual pressure measured between the pump and the closed
valve might exceed this value because a pump ADDS head to the liquid being pumped.
In other words, if this pump were operating at shutoff with suction pressure of 20 feet
the total head experienced at the pump discharge flange would be 150 ft (20 ft + 130 ft).
Considering the design trim impeller, we see that the following things are true:
 Shutoff (a.k.a. zero-flow or dead-head) occurs at about 130 ft.

 The design condition falls very close to the pumps best-efficiency-point (BEP).
 Provided there is adequate NPSHa, the pump will operate down to approximately
60 ft of head and produce a flow of approximately 1380 GPM at 60 ft.
The maximum (17″) and minimum (15″) trim curves also tell us the possible conditions
that the pump could be modified to meet in the future by installing an impeller of a larger
or smaller different trim.
Efficiency
In addition to head and flow, most pump performance curves will also provide efficiency
information.
The efficiency of a pump is the relationship between the input horsepower required to
drive the pump at a given operating condition, and the water horsepower being created
by the pump.
If a pump were 100% efficient then the input power required would be equal to the water
horsepower being generated by the pump. However, since no pump is 100% efficient,
every pump will require more input power than it will generate in water horsepower.
In the case of this pump, the best-efficiency-point (BEP) falls at approximately 1075
GPM at 95 Ft, and efficiency at BEP is 84.1%.
The Preferred Operating Range

Special attention should be paid to the location of BEP relative to the operating
condition. Pumps run best at or near BEP. For this reason the Hydraulic Institute (HI)
has defined a pumps Preferred Operating Region (POR) as flows from 70% to 120% of
flow at BEP for most centrifugal pumps.
The POR for this pump stretches from approximately 750 GPM to 1290 GPM which is
70% to 120% of 1075 GPM.
It is best to select a pump that will operate most of the time in the POR since this will
have implications for pump life and power consumption. For some pumps with high
specific speed (Ns) impellers, the POR is smaller – 85% to 110% of BEP. You can read
more about specific speed in our article about pump casings and impellers.
The Allowable Operating Range

There is another region of operation that is defined by the pump manufacturer rather
than by a standards organizations such as HI: the Allowable Operating Region (AOR).
In our example curve, the AOR is indicated by the portion of the curve shaded in light
yellow. This is the region that the pump manufacturer has determined comprises all of
the points that this pump can operate at continuously.
While it is preferable to select pumps to operate within the POR, pumps should always
be selected to operate within the AOR without exception. Very short-term operation
outside of the AOR might be acceptable, but the pump manufacturer should be
consulted before selecting a pump that will see intermittent operation outside the
confines of the AOR.
Minimum Continuous Stable Flow & the System

Curve
The example pump performance curve above has two more items which should be
mentioned.
First, the red line on the left hand side of the pump curve is the Minimum Continuous
Stable Flow (MCSF) line. This is the point beyond which the pump manufacturer has
determined the pump should not be allowed to operate for any extended period of time.
Second, the blue curve beginning at 0 GPM and 0 Ft and extending through the design
condition is the System Curve and represents the operation of the system in which the
pump is being applied.
System curve information should be provided by the Engineer designing the pump
system. In the pump selection software, the system curve can be manipulated by
manually entering data points, and is particularly useful when evaluating the variable-
speed performance of a pump.
Net Positive Suction Head Required (NPSHr)

Net Positive Suction Head
Required Curve
The next part of the pump
curve is the Net Positive
Suction Head Required (NPSHr) curve. The NPSHr curve provides information about
the suction characteristics of the pump at different flows. The x-axis is still measured in
flow units, but the y-axis is now measured in feet of NPSHr. Each point along the curve
identifies the NPSHr required by the pump at that flow to avoid cavitation issues that
would be damaging to the pump and would have a negative impact on overall pump
performance.
Looking back at our example design flow of 1,000 GPM we can see that this pump will
require approximately 7 ft of NPSHr at that condition. A typical safety margin between
Net Positive Suction Head Available (NPSHa) and required (NPSHr) is 5 ft. So in this
case it would generally be recommended that this pump not be applied in applications
where NPSHa at the design flow of 1,000 GPM is less than approximately 12 ft.
Generally speaking NPSHr does not vary dramatically between variations in impeller
trim which is why we do not see separate curves for the minimum and maximum
impeller trims. Those curves are actually present, but they are overlaid by the design-
trim NPSHr curve.
Horsepower Curve
Power Curve
The final portion of the pump
curve is the power curve. Once
again the x-axis is measured in
units of flow, but the y-axis is now measured in power units. In this case the unit of
measurement is horsepower, but in the case of an application measured in metric units,
power is typically measured in kilowatts. This curve tells us how much power the pump
will demand at any particular flow point. This information is useful in ensuring the
selected motor is suitably sized, and is also useful when calculating power consumption
costs.
At our design flow of 1,000 GPM, we can see that power demand is approximately 30
HP and that power demand is greatest at approximately 1,300 GPM. Based on this
information, if the pump were to be driven by an electric motor, most pump
manufacturer’s would recommend that the next largest motor rating be used. In this
case that would be a motor rated for 40 HP.
Power demands vary considerably depending on the impeller trim. This is why separate
power curves for the minimum and maximum impeller trims can also be seen in the
power curve. This information is useful if the customer would like to size the drive unit to
allow a future increase in capacity without requiring replacement of the drive unit. In that
case, the customer could chose to size the drive unit for the maximum trim power curve,
and at a later date the capacity of the pump could be increased by installing a maximum
trim impeller without requiring replacement of the drive unit. In the case of our example
pump curve, the motor required by the design trim impeller will be adequate to cover the
power demanded by the maximum trim impeller, but this will not always be the case.
In Conclusion
When combined, these three curves are called the composite pump curve, and they
provide the information we need to determine if a particular pump is a suitable selection
for the hydraulic requirements of an application. Understanding the information
communicated by each part of the curve is critical to ensuring that the pump selected is
a good fit for the application’s hydraulics.

How To Read A Pump Curve

Uploaded by

Copyright:

Available Formats

How To Read A Pump Curve

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

How To Read A Pump Curve

Uploaded by

Copyright:

Available Formats

How to Read a Pump Curve

This article is part of Pumps 101, an eleven-part series of articles designed as an

2. Volutes, Casings, and Impellers

3. Parts of a Centrifugal Pump

4. Centrifugal Pump Designs

5. How to Read a Pump Curve

6. How to Make a Pump Selection

8. How to Size an Electric Motor

9. Using a Pump with a VFD

10. Materials of Construction

11. Pump System Installation

What is a Pump Curve?

Head & Flow

 Shutoff (a.k.a. zero-flow or dead-head) occurs at about 130 ft.

The Preferred Operating Range

The Allowable Operating Range

Minimum Continuous Stable Flow & the System

Net Positive Suction Head Required (NPSHr)

You might also like