Page : 1 / 14

SAFETY DATA SHEET

Revision nr : 1.0
Issue date : 24/04/2023
Supersedes :
ANYCUBIC
High Speed Resin

SECTION 1: Identification of the substance/mixture and of the company/undertaking

1.1. Product identifier
Product form : Mixture
Trade name : ANYCUBIC
High Speed Resin
UFI : TV10-F0V7-M009-MVQS
1.2. Relevant identified uses of the substance or mixture and uses advised against
1.2.1. Relevant identified uses
Intended for general public
Main use category : Consumer use
Use of the substance/mixture : Resin

1.2.2. Uses advised against

No additional information available

1.3. Details of the supplier of the safety data sheet

Shenzhen Anycubic Technology Co.,Ltd
1201-1314, Unit B, Block 3，Vanke Times Square, No.85 Longcheng Avenue,Longcheng Street,Longgang District
518000 Shenzhen, Guangdong Province - China
T 17688757950
weiwulin@anycubic.com

1.4. Emergency telephone number

Emergency number : 17688757950
Only available during office hours.
Country Official advisory body Address Emergency number
Ireland National Poisons Information Centre PO Box 1297 +353 1 809 2566
Beaumont Road
Beaumont Hospital (Healthcare professionals-
9 Dublin
24/7)
+353 1 809 2166 (public,
8am - 10pm, 7/7)

SECTION 2: Hazards identification

2.1. Classification of the substance or mixture
Classification according to Regulation (EC) No. 1272/2008 [CLP]Mixtures/Substances: SDS EU > 2015: According to Regulation (EU)
2015/830, 2020/878 (REACH Annex II)
Skin Irrit. 2 H315
Eye Dam. 1 H318
Skin Sens. 1 H317
Aquatic Chronic 2 H411

Full text of H- and EUH-statements: see section 16

 Page : 2 / 14
SAFETY DATA SHEET
Revision nr : 1.0
Issue date : 24/04/2023
Supersedes :
ANYCUBIC
High Speed Resin

2.2. Label elements

Labelling according to Regulation (EC) No. 1272/2008 [CLP]
Hazard pictograms (CLP) :

GHS05 GHS07 GHS09

Signal word : Danger

Contains : oxybis(methyl-2,1-ethanediyl) diacrylate; 3-[2,2-dimethyl-1-oxo-3-[(1-
oxoallyl)oxy]propoxy]-2,2-dimethylpropyl acrylate; oxydi-2,1-ethanediyl bismethacrylate;
2-(2H-benzotriazol-2-yl)-p-cresol
Hazard statements (CLP) : H315 - Causes skin irritation.
H317 - May cause an allergic skin reaction.
H318 - Causes serious eye damage.
H411 - Toxic to aquatic life with long lasting effects.
Precautionary statements (CLP) : P101 - If medical advice is needed, have product container or label at hand.
P102 - Keep out of reach of children.
P273 - Avoid release to the environment.
P280 - Wear protective gloves, protective clothing, eye protection, face protection.
P305+P351+P338 - IF IN EYES: Rinse cautiously with water for several minutes. Remove
contact lenses, if present and easy to do. Continue rinsing.
P310 - Immediately call a POISON CENTER/doctor.
P391 - Collect spillage.
P501 - Dispose of contents and container to an approved waste disposal plant.
Child-resistant fastening : Not applicable
Tactile warning : Not applicable

2.3. Other hazards

Other hazards : Results of PBT and vPvB assessment : Contains no PBT/vPvB substances ≥ 0.1% assessed
in accordance with REACH Annex XIII.

The mixture does not contain substance(s) included in the list established in accordance with Article 59(1) of REACH for having endocrine
disrupting properties, or is not identified as having endocrine disrupting properties in accordance with the criteria set out in Commission
Delegated Regulation (EU) 2017/2100 or Commission Regulation (EU) 2018/605 at a concentration equal to or greater than 0,1 %

SECTION 3: Composition/information on ingredients

3.1. Substances
Not applicable

3.2. Mixtures

Substance name Product identifier % Classification according to

Regulation (EC) No.
1272/2008 [CLP]
oxybis(methyl-2,1-ethanediyl) diacrylate (CAS-No.) 57472-68-1 20 – 45 Skin Irrit. 2, H315
(EC-No.) 260-754-3 Eye Dam. 1, H318
Skin Sens. 1, H317
Poly(oxy-1,2-ethanediyl), .alpha.,.alpha.'-[(1-methylethylidene)di- (CAS-No.) 64401-02-1 20 – 25 Aquatic Chronic 2, H411
4,1-phenylene]bis[.omega.-[(1-oxo-2-propen-1-yl)oxy]- (EC-No.) 613-584-2
3-[2,2-dimethyl-1-oxo-3-[(1-oxoallyl)oxy]propoxy]-2,2- (CAS-No.) 30145-51-8 15 – 20 Skin Sens. 1, H317
dimethylpropyl acrylate (EC-No.) 250-072-4
 Page : 3 / 14
SAFETY DATA SHEET
Revision nr : 1.0
Issue date : 24/04/2023
Supersedes :
ANYCUBIC
High Speed Resin

oxydi-2,1-ethanediyl bismethacrylate (CAS-No.) 2358-84-1 10 – 20 Skin Sens. 1, H317

(EC-No.) 219-099-9
2-(2H-benzotriazol-2-yl)-p-cresol (CAS-No.) 2440-22-4 0 – 0,5 Skin Sens. 1B, H317
(EC-No.) 219-470-5 Aquatic Chronic 1, H410

Full text of H- and EUH-statements: see section 16

SECTION 4: First aid measures

4.1. Description of first aid measures
Additional advice : First aider: Pay attention to self-protection!. Concerning personal protective equipment to
use, see section 8. Never give anything by mouth to an unconscious person. In case of doubt
or persistent symptoms, consult always a physician. Show this safety data sheet to the
doctor in attendance.
Inhalation : Remove casualty to fresh air and keep warm and at rest. In case of doubt or persistent
symptoms, consult always a physician.
Skin contact : Remove contaminated clothing and shoes. Gently wash with plenty of soap and water. In
case of doubt or persistent symptoms, consult always a physician.
Eyes contact : Rinse immediately carefully and thoroughly with eye-bath or water. Remove contact lenses,
if present and easy to do. Continue rinsing. Get immediate medical advice/attention.
Ingestion : Rinse mouth thoroughly with water. Get medical advice/attention.
4.2. Most important symptoms and effects, both acute and delayed
Inhalation : May cause irritation to the respiratory tract.
Skin contact : May cause an allergic skin reaction. Causes skin irritation. The following symptoms may
occur: Redness, pain.
Eyes contact : Causes serious eye damage. The following symptoms may occur: Redness, pain.
Ingestion : May cause gastrointestinal irritation, nausea, vomiting and diarrhoea.
4.3. Indication of any immediate medical attention and special treatment needed
Treat symptomatically.

SECTION 5: Firefighting measures

5.1. Extinguishing media
Suitable extinguishing media : carbon dioxide (CO2), powder, alcohol-resistant foam, water spray.
Unsuitable extinguishing media : Strong water jet.
5.2. Special hazards arising from the substance or mixture
Specific hazards : Combustible. Vapours are heavier than air and may travel considerable distance to an
ignition source and flash back to source of vapours. Can form explosive mixture with air.
Heating will cause a rise in pressure with a risk of bursting.
Hazardous decomposition products in case of : Carbon oxides (CO, CO2).
fire
5.3. Advice for firefighters
Firefighting instructions : Evacuate area. Use water spray or fog for cooling exposed containers. Contain the
extinguishing fluids by bunding. Prevent fire fighting water from entering the environment.
Protection during firefighting : Do not attempt to take action without suitable protective equipment. Self-contained
breathing apparatus.
Other information : Do not allow run-off from fire-fighting to enter drains or water courses. Dispose of waste in
accordance with environmental legislation.
 Page : 4 / 14
SAFETY DATA SHEET
Revision nr : 1.0
Issue date : 24/04/2023
Supersedes :
ANYCUBIC
High Speed Resin

SECTION 6: Accidental release measures

6.1. Personal precautions, protective equipment and emergency procedures
6.1.1. For non-emergency personnel
For non-emergency personnel : Evacuate unnecessary personnel. Keep upwind. Provide adequate ventilation. Do not
breathe vapours. Avoid contact with skin, eyes and clothing. Wear recommended personal
protective equipment. Concerning personal protective equipment to use, see section 8.
Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No
smoking. Ensure equipment is adequately earthed. Use explosion-proof equipment. Use
only non-sparking tools.

6.1.2. For emergency responders

For emergency responders : Ensure procedures and training for emergency decontamination and disposal are in place.
Concerning personal protective equipment to use, see section 8.
6.2. Environmental precautions
Do not allow to enter into surface water or drains. Notify authorities if product enters sewers or public waters.
6.3. Methods and material for containment and cleaning up
Methods for cleaning up : Stop leak if safe to do so. Dam up the liquid spill. Small quantities of liquid spill: take up in
non-combustible absorbent material and shovel into container for disposal. Recover large
spills by pumping (use an explosion proof or hand pump). Place in a suitable container for
disposal in accordance with the waste regulations (see Section 13). This material and its
container must be disposed of in a safe way, and as per local legislation.
6.4. Reference to other sections
Concerning personal protective equipment to use, see section 8. Concerning disposal elimination after cleaning, see section 13.

SECTION 7: Handling and storage

7.1. Precautions for safe handling
Precautions for safe handling : Provide adequate ventilation. Do not breathe vapours. Avoid contact with skin, eyes and
clothing. Use personal protective equipment as required. Concerning personal protective
equipment to use, see section 8. Take any precaution to avoid mixing with Incompatible
materials, Refer to Section 10 on Incompatible Materials. Ensure proper process control to
avoid excess waste discharge (temperature, concentration, pH, time). Avoid release to the
environment. Contaminated work clothing must not be allowed out of the workplace. Keep
away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.
Ground/bond container and receiving equipment. Use explosion-proof equipment. Use only
non-sparking tools.
Hygiene measures : Keep good industrial hygiene. Wash hands and other exposed areas with mild soap and
water before eating, drinking or smoking and when leaving work. Do not eat, drink or smoke
when using this product. Keep away from food, drink and animal feedingstuffs. Remove
contaminated clothes. Separate working clothes from town clothes. Launder separately.
Wash contaminated clothing before reuse.
7.2. Conditions for safe storage, including any incompatibilities
Storage conditions : Store in a dry, cool and well-ventilated place. Do not store near or with any of the
incompatible materials listed in section 10. Bund storage facilities to prevent soil and water
pollution in the event of spillage.
Heat and ignition sources : Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No
smoking. Protect from sunlight.
Special rules on packaging : Containers which are opened should be properly resealed and kept upright to prevent
leakage.
Packaging materials : Keep only in the original container.
7.3. Specific end use(s)
Resin.
 Page : 5 / 14
SAFETY DATA SHEET
Revision nr : 1.0
Issue date : 24/04/2023
Supersedes :
ANYCUBIC
High Speed Resin

SECTION 8: Exposure controls/personal protection

8.1. Control parameters

Additional information : Recommended monitoring procedures :. Personal air monitoring. Room air monitoring
8.2. Exposure controls
Engineering measure(s) : Provide adequate ventilation. Organisational measures to prevent/limit releases, dispersion
and exposure. See Section 7 for information on safe handling. Emergency eye wash
fountains and safety showers should be available in the immediate vicinity of any potential
exposure. Take precautionary measures against static discharges. Ensure equipment is
adequately earthed.
Personal protective equipment : The type of protective equipment must be selected according to the concentration and
amount of the dangerous substance at the specific workplace.
Hand protection : Wear chemically resistant gloves (tested to EN374) . Suitable material: Not determined.
Breakthrough time : refer to the recommendations of the supplier. Thickness : Not
determined. The quality of the protective gloves resistant to chemicals must be chosen as a
function of the specific working place concentration and quantity of hazardous substances.
Eye protection : Use suitable eye protection (EN166): goggles. face shield
Body protection : Wear suitable protective clothing
Respiratory protection : In case of insufficient ventilation, wear suitable respiratory equipment. Half-face mask (DIN
EN 140). full face mask (DIN EN 136). Filter type: ABEK (EN 14387). The filter class must be
suitable for the maximum contaminant concentration (gas/vapour/aerosol/particulates)
that may arise when handling the product. If the concentration is exceeded, self-contained
breathing apparatus must be used. (EN 137)
Thermal hazard protection : Not required for normal conditions of use. Use dedicated equipment.
Environmental exposure controls : Avoid release to the environment. Comply with applicable Community environmental
protection legislation.

SECTION 9: Physical and chemical properties

9.1. Information on basic physical and chemical properties
Physical state : Liquid
Appearance : Liquid.
Colour : Grey.
Odour : odourless.
Odour threshold : No data available
pH : No data available
Relative evaporation rate (butylacetate=1) : No data available
Melting / freezing point : No data available
Freezing point : No data available
Initial boiling point and boiling range : 238 °C
Flash point : 90 °C
Auto-ignition temperature : 252 °C
Decomposition temperature : No data available
Flammability : Not applicable,liquid
Vapour pressure : No data available
Vapour density : No data available
Relative density : No data available
 Page : 6 / 14
SAFETY DATA SHEET
Revision nr : 1.0
Issue date : 24/04/2023
Supersedes :
ANYCUBIC
High Speed Resin

Solubility : Insoluble in water. Soluble in ethanol.

Partition coefficient n-octanol/water : No data available
Kinematic viscosity : 50 – 150 mm²/s (25 °C)
Dynamic viscosity : No data available
Explosive properties : Not applicable. The study does not need to be conducted because there are no chemical
groups associated with explosive properties present in the molecule.
Oxidising properties : Not applicable. The classification procedure needs not to be applied because there are
no chemical groups present in the molecule which are associated with oxidising
properties.
Explosive limits : No data available
Particle size : Not applicable
Particle size distribution : Not applicable
Particle shape : Not applicable
Particle aspect ratio : Not applicable
Particle aggregation state : Not applicable
Particle agglomeration state : Not applicable
Particle specific surface area : Not applicable
Particle dustiness : Not applicable

9.2. Other information

9.2.1. Information with regard to physical hazard classes
No additional information available

9.2.2. Other safety characteristics

No additional information available

SECTION 10: Stability and reactivity

10.1. Reactivity
Combustible. Reference to other sections: 10.4 & 10.5.
10.2. Chemical stability
Stable under normal conditions.
10.3. Possibility of hazardous reactions
No dangerous reactions known under normal conditions of use.
10.4. Conditions to avoid
Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Protect from sunlight. See Section 7 for
information on safe handling.
10.5. Incompatible materials
Strong oxidizing agents. See Section 7 for information on safe handling.
10.6. Hazardous decomposition products
Reference to other sections 5.2.

SECTION 11: Toxicological information

11.1. Information on hazard classes as defined in Regulation (EC) No 1272/2008
Acute toxicity : Not classified (Based on available data, the classification criteria are not met)
 Page : 7 / 14
SAFETY DATA SHEET
Revision nr : 1.0
Issue date : 24/04/2023
Supersedes :
ANYCUBIC
High Speed Resin

oxybis(methyl-2,1-ethanediyl) diacrylate (57472-68-1)

LD50/oral/rat 4600 mg/kg
LD50/dermal/rabbit > 2000 mg/kg
2-(2H-benzotriazol-2-yl)-p-cresol (2440-22-4)
LD50/oral/rat > 10000 mg/kg
LC50/inhalation/4h/rat > 1420 mg/m³ (Exposure time: 4 h)
Skin corrosion/irritation : Causes skin irritation.
pH: No data available
Serious eye damage/irritation : Causes serious eye damage.
pH: No data available
Respiratory or skin sensitisation : May cause an allergic skin reaction.
Germ cell mutagenicity : Not classified (Based on available data, the classification criteria are not met)
Carcinogenicity : Not classified (Based on available data, the classification criteria are not met)
Reproductive toxicity : Not classified (Based on available data, the classification criteria are not met)
STOT-single exposure : Not classified (Based on available data, the classification criteria are not met)
STOT-repeated exposure : Not classified (Based on available data, the classification criteria are not met)
Aspiration hazard : Not classified (Based on available data, the classification criteria are not met)
ANYCUBIC
High Speed Resin
Kinematic viscosity 50 – 150 mm²/s (25 °C)
Other information : Symptoms related to the physical, chemical and toxicological characteristics. For further
information see section 4.

11.2. Information on other hazards

11.2.1. Endocrine disrupting properties

Adverse health effects caused by endocrine : The mixture does not contain substance(s) included in the list established in accordance
disrupting properties with Article 59(1) of REACH for having endocrine disrupting properties, or is not
identified as having endocrine disrupting properties in accordance with the criteria set
out in Commission Delegated Regulation (EU) 2017/2100 or Commission Regulation (EU)
2018/605 at a concentration equal to or greater than 0,1 %
11.2.2 Other information
Other information : Symptoms related to the physical, chemical and toxicological characteristics,For further
information see section 4

SECTION 12: Ecological information

12.1. Toxicity
Environmental properties : Toxic to aquatic life with long lasting effects.

Hazardous to the aquatic environment, short– : Not classified

term (acute)
Hazardous to the aquatic environment, long–term : Toxic to aquatic life with long lasting effects.
(chronic)
 Page : 8 / 14
SAFETY DATA SHEET
Revision nr : 1.0
Issue date : 24/04/2023
Supersedes :
ANYCUBIC
High Speed Resin

12.2. Persistence and degradability

ANYCUBIC
High Speed Resin
Persistence and degradability No additional information available.

12.3. Bioaccumulative potential

ANYCUBIC
High Speed Resin
Partition coefficient n-octanol/water No data available
Bioaccumulative potential No additional information available.

oxybis(methyl-2,1-ethanediyl) diacrylate (57472-68-1)

Partition coefficient n-octanol/water 0,01 – 0,39 (at 24 °C (at pH 7)

Poly(oxy-1,2-ethanediyl), .alpha.,.alpha.'-[(1-methylethylidene)di-4,1-phenylene]bis[.omega.-[(1-oxo-2-propen-1-yl)oxy]- (64401-02-1)

Partition coefficient n-octanol/water 2,45 – 4,16 (at pH 6.97)

2-(2H-benzotriazol-2-yl)-p-cresol (2440-22-4)
BCF - Fish [1] 123 – 494
Partition coefficient n-octanol/water 4,2 (at 25 °C (at pH 6.3)

12.4. Mobility in soil

ANYCUBIC
High Speed Resin
Mobility in soil No data available

12.5. Results of PBT and vPvB assessment

ANYCUBIC
High Speed Resin
Results of PBT assessment Contains no PBT/vPvB substances ≥ 0.1% assessed in accordance with REACH Annex XIII

12.6. Endocrine disrupting properties

Adverse effects on the environment caused by : The mixture does not contain substance(s) included in the list established in accordance
endocrine disrupting properties with Article 59(1) of REACH for having endocrine disrupting properties, or is not
identified as having endocrine disrupting properties in accordance with the criteria set
out in Commission Delegated Regulation (EU) 2017/2100 or Commission Regulation (EU)
2018/605 at a concentration equal to or greater than 0,1 %

12.7. Other adverse effects

Other adverse effects : No data available
 Page : 9 / 14
SAFETY DATA SHEET
Revision nr : 1.0
Issue date : 24/04/2023
Supersedes :
ANYCUBIC
High Speed Resin

SECTION 13: Disposal considerations

13.1. Waste treatment methods
Product/Packaging disposal recommendations : Avoid release to the environment. Dispose of empty containers and wastes safely. See
Section 7 for information on safe handling. Refer to manufacturer/supplier for information
on recovery/recycling. Recycling is preferred to disposal or incineration. If recycling is not
possible, eliminate in accordance with local valid waste disposal regulations. Handle
contaminated packages in the same way as the substance itself. Dispose of contaminated
materials in accordance with current regulations. Packaging contaminated by the product :
Do not pierce or burn, even after use. Never use pressure to empty container.
European waste catalogue (2001/573/EC, : This material and its container must be disposed of as hazardous waste
75/442/EEC, 91/689/EEC) Waste codes should be assigned by the user, preferably in discussion with the waste
disposal authorities

SECTION 14: Transport information

In accordance with ADR / RID / IMDG / IATA / ADN
ADR IMDG IATA ADN RID
14.1. UN number or ID number
3082 3082 3082 3082 3082
14.2. UN proper shipping name
ENVIRONMENTALLY ENVIRONMENTALLY Environmentally ENVIRONMENTALLY ENVIRONMENTALLY
HAZARDOUS SUBSTANCE, HAZARDOUS SUBSTANCE, hazardous substance, HAZARDOUS SUBSTANCE, HAZARDOUS SUBSTANCE,
LIQUID, N.O.S. (Poly(oxy- LIQUID, N.O.S. (Poly(oxy- liquid, n.o.s. (Poly(oxy- LIQUID, N.O.S. (Poly(oxy- LIQUID, N.O.S. (Poly(oxy-
1,2-ethanediyl), 1,2-ethanediyl), 1,2-ethanediyl), 1,2-ethanediyl), 1,2-ethanediyl),
.alpha.,.alpha.'-[(1- .alpha.,.alpha.'-[(1- .alpha.,.alpha.'-[(1- .alpha.,.alpha.'-[(1- .alpha.,.alpha.'-[(1-
methylethylidene)di-4,1- methylethylidene)di-4,1- methylethylidene)di-4,1- methylethylidene)di-4,1- methylethylidene)di-4,1-
phenylene]bis[.omega.- phenylene]bis[.omega.- phenylene]bis[.omega.- phenylene]bis[.omega.- phenylene]bis[.omega.-
[(1-oxo-2-propen-1- [(1-oxo-2-propen-1- [(1-oxo-2-propen-1- [(1-oxo-2-propen-1- [(1-oxo-2-propen-1-
yl)oxy]-) yl)oxy]-) yl)oxy]-) yl)oxy]-) yl)oxy]-)
Transport document description
UN 3082 UN 3082 UN 3082 Environmentally UN 3082 UN 3082
ENVIRONMENTALLY ENVIRONMENTALLY hazardous substance, ENVIRONMENTALLY ENVIRONMENTALLY
HAZARDOUS SUBSTANCE, HAZARDOUS SUBSTANCE, liquid, n.o.s. (Poly(oxy- HAZARDOUS SUBSTANCE, HAZARDOUS SUBSTANCE,
LIQUID, N.O.S. (Poly(oxy- LIQUID, N.O.S. (Poly(oxy- 1,2-ethanediyl), LIQUID, N.O.S. (Poly(oxy- LIQUID, N.O.S. (Poly(oxy-
1,2-ethanediyl), 1,2-ethanediyl), .alpha.,.alpha.'-[(1- 1,2-ethanediyl), 1,2-ethanediyl),
.alpha.,.alpha.'-[(1- .alpha.,.alpha.'-[(1- methylethylidene)di-4,1- .alpha.,.alpha.'-[(1- .alpha.,.alpha.'-[(1-
methylethylidene)di-4,1- methylethylidene)di-4,1- phenylene]bis[.omega.- methylethylidene)di-4,1- methylethylidene)di-4,1-
phenylene]bis[.omega.- phenylene]bis[.omega.- [(1-oxo-2-propen-1- phenylene]bis[.omega.- phenylene]bis[.omega.-
[(1-oxo-2-propen-1- [(1-oxo-2-propen-1- yl)oxy]-), 9, III [(1-oxo-2-propen-1- [(1-oxo-2-propen-1-
yl)oxy]-), 9, III, (-) yl)oxy]-), 9, III, MARINE yl)oxy]-), 9, III yl)oxy]-), 9, III
POLLUTANT

14.3. Transport hazard class(es)

9 9 9 9 9

14.4. Packing group

III III III III III
14.5. Environmental hazards
Dangerous for the Dangerous for the Dangerous for the Dangerous for the Dangerous for the
environment : Yes environment : Yes environment : Yes environment : Yes environment : Yes
Marine pollutant : Yes
 Page : 10 / 14
SAFETY DATA SHEET
Revision nr : 1.0
Issue date : 24/04/2023
Supersedes :
ANYCUBIC
High Speed Resin

ADR IMDG IATA ADN RID

No supplementary information available

14.6. Special precautions for user

Special precautions for user : No data available

- Overland transport
Classification code (ADR) : M6
Special provisions : 274, 335, 375, 601
Limited quantities (ADR) : 5l
Excepted quantities (ADR) : E1
Packing instructions (ADR) : P001, IBC03, LP01, R001
Special packing provisions (ADR) : PP1
Mixed packing provisions (ADR) : MP19
Portable tank and bulk container : T4
instructions (ADR)
Portable tank and bulk container special : TP1, TP29
provisions (ADR)
Tank code (ADR) : LGBV
Vehicle for tank carriage : AT
Transport category (ADR) : 3
Special provisions for carriage - Packages : V12
(ADR)
Special provisions for carriage - Loading, : CV13
unloading and handling (ADR)
Hazard identification number (Kemler No.) : 90
Orange plates :

Tunnel restriction code : -

EAC code : •3Z

- Transport by sea
Special provisions (IMDG) : 274, 335, 969
Limited quantities (IMDG) : 5L
Excepted quantities (IMDG) : E1
Packing instructions (IMDG) : LP01, P001
Special packing provisions (IMDG) : PP1
IBC packing instructions (IMDG) : IBC03
Tank instructions (IMDG) : T4
Tank special provisions (IMDG) : TP1, TP29
EmS-No. (Fire) : F-A
EmS-No. (Spillage) : S-F
Stowage category (IMDG) : A

- Air transport
PCA Excepted quantities (IATA) : E1
PCA Limited quantities (IATA) : Y964
 Page : 11 / 14
SAFETY DATA SHEET
Revision nr : 1.0
Issue date : 24/04/2023
Supersedes :
ANYCUBIC
High Speed Resin

PCA limited quantity max net quantity (IATA) : 30kgG

PCA packing instructions (IATA) : 964
PCA max net quantity (IATA) : 450L
CAO packing instructions (IATA) : 964
CAO max net quantity (IATA) : 450L
Special provisions (IATA) : A97, A158, A197, A215
ERG code (IATA) : 9L

- Inland waterway transport

Classification code (ADN) : M6
Special provisions (ADN) : 274, 335, 375, 601
Limited quantities (ADN) : 5L
Excepted quantities (ADN) : E1
Carriage permitted (ADN) : T
Equipment required (ADN) : PP
Number of blue cones/lights (ADN) : 0

- Rail transport
Classification code (RID) : M6
Special provisions (RID) : 274, 335, 375, 601
Limited quantities (RID) : 5L
Excepted quantities (RID) : E1
Packing instructions (RID) : P001, IBC03, LP01, R001
Special packing provisions (RID) : PP1
Mixed packing provisions (RID) : MP19
Portable tank and bulk container instructions : T4
(RID)
Portable tank and bulk container special : TP1, TP29
provisions (RID)
Tank codes for RID tanks (RID) : LGBV
Transport category (RID) : 3
Special provisions for carriage – Packages (RID) : W12
Special provisions for carriage - Loading, : CW13, CW31
unloading and handling (RID)
Colis express (express parcels) (RID) : CE8
Hazard identification number (RID) : 90
14.7. Maritime transport in bulk according to IMO instruments
Code: IBC : No data available.

SECTION 15: Regulatory information

15.1. Safety, health and environmental regulations/legislation specific for the substance or mixture
15.1.1. EU-Regulations
Listed on REACH Annex XVII (Restriction Conditions). The following restrictions are applicable:
3(b) Substances or mixtures fulfilling the criteria for any of the following hazard classes or categories ANYCUBIC
set out in Annex I to Regulation (EC) No 1272/2008: Hazard classes 3.1 to 3.6, 3.7 adverse effects on High Speed Resin
sexual function and fertility or on development, 3.8 effects other than narcotic effects, 3.9 and 3.10
 Page : 12 / 14
SAFETY DATA SHEET
Revision nr : 1.0
Issue date : 24/04/2023
Supersedes :
ANYCUBIC
High Speed Resin

3(c) Substances or mixtures fulfilling the criteria for any of the following hazard classes or categories ANYCUBIC
set out in Annex I to Regulation (EC) No 1272/2008: Hazard class 4.1 High Speed Resin ; Poly(oxy-1,2-ethanediyl),
.alpha.,.alpha.'-[(1-methylethylidene)di-4,1-
phenylene]bis[.omega.-[(1-oxo-2-propen-1-yl)oxy]-

Contains no substance(s) listed on the REACH Candidate List

Contains no substance(s) listed on REACH Annex XIV (Authorisation List)

15.1.2. National regulations

France
Installations classées
No ICPE Désignation de la rubrique Code Régime Rayon
na Not Applicable na na

Germany
Regulatory reference : WGK 3, Highly hazardous to water (Classification according to AwSV, Annex 1)
German storage class (LGK) : LGK 10 - Combustible liquids
Employment restrictions : Observe restrictions according Act on the Protection of Working Mothers (MuSchG)
Observe restrictions according Act on the Protection of Young People in Employment
(JArbSchG)
Hazardous Incident Ordinance (12. BImSchV) : Listed in the 12. BlmSchV (Annex I) under: 1.3.2
Quantity threshold for operational area under § 1 para. 1
- Sentence 1: 200000 kg
- Sentence 2: 500000 kg

Netherlands
Waterbezwaarlijkheid : A (2) - Vergiftig voor in water levende organismen
kan in het aquatische milieu op lange termijn schadelijke effecten veroorzaken
SZW-lijst van kankerverwekkende stoffen : None of the components are listed
SZW-lijst van mutagene stoffen : None of the components are listed
SZW-lijst van reprotoxische stoffen – : None of the components are listed
Borstvoeding
SZW-lijst van reprotoxische stoffen – : None of the components are listed
Vruchtbaarheid
SZW-lijst van reprotoxische stoffen – : None of the components are listed
Ontwikkeling

Denmark
Class for fire hazard : Class III-1
Store unit : 50 liter
Classification remarks : Flammable according to the Danish Ministry of Justice; Emergency management guidelines
for the storage of flammable liquids must be followed
Recommendations Danish Regulation : Young people below the age of 18 years are not allowed to use the product

15.2. Chemical safety assessment

Not applicable
 Page : 13 / 14
SAFETY DATA SHEET
Revision nr : 1.0
Issue date : 24/04/2023
Supersedes :
ANYCUBIC
High Speed Resin

SECTION 16: Other information

Abbreviations and acronyms:
ABM = Algemene beoordelingsmethodiek
ADN = Accord Européen relatif au Transport International des Marchandises Dangereuses par voie de Navigation du Rhin
ADR = Accord européen relatif au transport international des marchandises Dangereuses par Route
CLP = Classification, Labelling and Packaging Regulation according to 1272/2008/EC
IATA = International Air Transport Association
IMDG = International Maritime Dangerous Goods Code
LEL = Lower Explosive Limit/Lower Explosion Limit
UEL = Upper Explosion Limit/Upper Explosive Limit
REACH = Registration, Evaluation, Authorisation and Restriction of Chemicals
BTT = Breakthrough time (maximum wearing time)
DMEL = Derived Minimal Effect level
DNEL = Derived No Effect Level
EC50 = Median Effective Concentration
EL50 = Median effective level
ErC50 = EC50 in terms of reduction of growth rate
ErL50 = EL50 in terms of reduction of growth rate
EWC = European waste catalogue
LC50 = Median lethal concentration
LD50 = Median lethal dose
LL50 = Median lethal level
NA = Not applicable
NOEC = No observed effect concentration
NOEL: no-observed-effect level
NOELR = No observed effect loading rate
NOAEC = No observed adverse effect concentration
NOAEL = No observed adverse effect level
N.O.S. = Not Otherwise Specified
OEL = Occupational Exposure Limits - Short Term Exposure Limits (STELs)
PNEC = Predicted No Effect Concentration
Quantitative structure-activity relationship (QSAR)
STOT = Specific Target Organ Toxicity
TWA = time weighted average
VOC = Volatile organic compounds
WGK = Wassergefährdungsklasse (Water Hazard Class under German Federal Water Management Act)

Sources of key data used to compile the : ECHA (European Chemicals Agency). LOLI. Supplier information.
datasheet
Training advice : Training staff on good practice. Manipulations are to be done only by qualified and
authorised persons.
Other information : Classification - Assessment method: CLP Calculation method (Article 9). Physicochemical
hazard assessment: Information given is based on tests on the mixture itself.

Full text of H- and EUH-statements:

Aquatic Chronic 1 Hazardous to the aquatic environment – Chronic Hazard, Category 1
Aquatic Chronic 2 Hazardous to the aquatic environment – Chronic Hazard, Category 2
Eye Dam. 1 Serious eye damage/eye irritation, Category 1
H315 Causes skin irritation.
H317 May cause an allergic skin reaction.
H318 Causes serious eye damage.
H410 Very toxic to aquatic life with long lasting effects.
 Page : 14 / 14
SAFETY DATA SHEET
Revision nr : 1.0
Issue date : 24/04/2023
Supersedes :
ANYCUBIC
High Speed Resin

H411 Toxic to aquatic life with long lasting effects.

Skin Irrit. 2 Skin corrosion/irritation, Category 2
Skin Sens. 1 Skin sensitisation, Category 1
Skin Sens. 1B Skin sensitisation, category 1B

according to Regulation (EC) No. 1907/2006 (REACH) with its amendment Regulation (EU) 2020/878
Classification according to Regulation (EC) No. 1272/2008 [CLP]
Labelling according to Regulation (EC) No. 1272/2008 [CLP]

DISCLAIMER OF LIABILITY The information in this SDS was obtained from sources which we believe are reliable. However, the information is
provided without any warranty, express or implied, regarding its correctness. The conditions or methods of handling, storage, use or disposal
of the product are beyond our control and may be beyond our knowledge. For this and other reasons, we do not assume responsibility and
expressly disclaim liability for loss, damage or expense arising out of or in any way connected with the handling, storage, use or disposal of the
product. This SDS was prepared and is to be used only for this product. If the product is used as a component in another product, this SDS
information may not be applicable.