DANATRONICS DJ Series

Videoscope
Product Manual
Inspection technology for better future.

Please read the manual before using the equipment.

 Declaration

The manual is only intended to be used for the DJ Series

As this manual is used a product series manual, the configuration and function of

different products may slightly differ depending on your exact configuration. The

technical specifications are only for reference.

 MENU
Instruction Before Use ........................................................................... 1

Main Configuration ............................................................................. 1

Button and Port................................................................................... 3

Application ........................................................................................... 5

After-service ........................................................................................ 5

Warning ............................................................................................... 5

1 Brief Introduction ................................................................................. 6

1.1 Parameters ................................................................................... 6

2 Operation Steps .................................................................................. 9

2.1 Take out the instrument ............................................................. 9

2.2 Boot preparation ......................................................................... 9

2.3 Operation .................................................................................... 10

2.4 Probe articulation control ......................................................... 11

2.5 After use ...................................................................................... 11

3 Image Capture and Operation ........................................................ 13

3.1 Photo/Video ................................................................................ 13

3.2 Temperature indication & alarm (optional, not standard

configuration) .................................................................................... 13

3.3 Image special effects ................................................................ 14

3.4 Exposure control ........................................................................ 14

 3.5 Playback ..................................................................................... 14

3.6 Measuring function(optional, not standard configuration) ... 15

3.7 Zoom in/out................................................................................. 15

3.8 Language setting ....................................................................... 15

3.9 Date&Time setting ..................................................................... 15

3.10 Auto shut off ............................................................................. 16

3.11 Date Stamp .............................................................................. 16

3.12 Formatting ................................................................................ 16

3.13 Factory reset ............................................................................ 16

3.14 Firmware update ..................................................................... 16

4 Solution to Common Problems .................................................. 15

Instruction Before Use

Main Configuration

Instrument Case

Micro USB/ charger

Videoscope
TF card reader

Base(optional)

1
For the specific configuration, please refers to the packing list.

Name Specs Qty Note

Case 432*386*163 mm3 1

Videoscope 324.3*161.3*91.2mm3 1

Base 215*84*36mm3 1 Optional

TF card reader 1

Rechargeable Battery φ18mm×65mm 1 Optional for 2pcs

Micro USB Line 1m 1

Charger 1

2
 Button and Port

working indicator

⑷ return

⑴ menu ⑸ playback

⑵ ok/function switch ⑹ up

⑺ down
⑶ brightness control

⑽ resetting

⑾ HDMI

⑻ front view/side view switch

⑿ TF card

⒀ Micro USB

⒁charging port
⑼ photo/video

⒂ on/off

power indicator

3
（1） Menu: function setting including language setting/ time setting
/firmware update.

（2） Ok: in menu setting mode, it serves as a validation button; in preview

mode, press ok button, it serves as function switch button.

（3） Brightness control: control the light from 0-9 levels.

（4） Return: return to previous menu.

（5） Playback: in preview mode, press this button, it will go to

image/video playback page.

（6） Up: in menu setting mode, press this button to upward navigation;

in preview mode, after pressing OK button, it can adjust the relative

function variable.

（7） Down: in menu setting mode, press this button to downward

navigation; in preview mode, after pressing OK button, it can adjust
the relative function variable.

（8） Front view/side view switch: In preview mode, press this button to
switch between front view and side view lens. (only available for dual
lens model)

（9） Photo/video: short press for taking photo, long press for taking video.
In video mode, short press for snapping a picture.

（10） Resetting: when the monitor does not work for abnormal reason,
press this hole by needle, it will restart.

（11） HDMI: connect the monitor with display by HDMI cable, the image on
the monitor will be displayed synchronously on the display.

4
 （12） TF card: please use Class 10 or above TF card. Maximum: 32G.

（13） Micro USB: When the monitor works independently, it serves as

power input port. When it connects with power bank or mobile phone
charging adapter, the monitor will turn on automatically.

（14） Micro USB charging port: power charging: DC5V, maximum

current:1A.

(15) On/off: Long press this button for 3 seconds to boot; long press it for
3 seconds to shut down. On the status of shut off, short press it, the

power indicator will show the current power of the batteries. The

current power of the two batteries will be indicated separately, orange light
shows the power of inner battery, white light shows the current power of outer
battery. When the product is charging, the indicator will flash. When the
product is turned on, the indicator will show the current power all the time.

Application

This product is only applied in the real-time detection and analysis for industrial
equipment and automobile production and maintenance.

After-service

This product has not any spare parts which can be repair by users. Any
disassemble, refit or maintenance is not allowed. If damage and losses
caused by this, we do not assume any responsibility. The product
maintenance is only afforded by the authorized dealers and distributors.

Warning

warning

5
 ·Prohibit the use of this instrument to observe the body or the animal's body;

·Do not use the product to inspect equipment in action;

·Do not use or store the product on explosive, strong electromagnetic field or
with combustible gas, otherwise it may cause fire or explosion;

·Do not use the product to check objects with current carrying, so as to avoid
the occurrence of electric shock;

·Do not watch the LED light source at the end of the lens straightly, avoiding
the effect of strong light on the visual acuity;

·Never excessive bending, stretching, twisting, rolling cable, otherwise it may

cause cable disconnect, a fire or electric shock accident;

·If there is abnormal in the angle adjustment operation, stop the current
operation, and turn off. Then contact the supplier;

·Keep the insert tube away from any liquid, except water, salty water or oil;

·When finish using, please clean the front section of the instrument in time, to
prevent corrosion.

1 Brief Introduction

1.1 Parameters

Probe Diameter(mm) Φ6/Φ3.9/Φ2.8

Camera Pixels 1000,000

DOF 5mm-100mm (optional:10~150mm)

FOV 120° (optional: 80°)

Viewing Direction 0° front view (optional: 90°sideview)

6
Illuminance Maximum:100000lx

Tube Material Tungsten braided

Tube Length 1.5m (customized for other length)

Protecting Device of buffer protection device between the host and

Durability wear-resistant tube
Articulation 360° all way

Bending Angle ≥160°

Probe Positioning damping positioning (optional: articulation

locking device)
Display 5.1 inches color IPS display, all sight viewing
angle
Display Resolution 1280*960

Language Chinese/English/Russian…8 languages

Image/Video Format JPEG/MOV

Image Format 1280*720

Video Format 1280*720

IR Function IR night vision/ IR thermal imaging (optional)

Outer Case Material anti-fall engineering alloy material

Water/Dust Proof probe/tube: IP67

Monitor Structure one hand-held monitor

Memory standard TF card 16G, maximum: 32G

Data Port HDMI port/Micro USB port

Working Time ≥4H, built-in batteries:8H

Batteries detachable lithium batteries (optional: built-in

lithium batteries)
Battery Capacity 3.7V，3200mAh*2pcs

7
Power Consumption 2W

Power Charge DC5V, maximum current:1A

Weight 0.55~0.8kg (including 2 batteries)

replaceable monitor and tube with different

Compatibility
diameter

Store Temperature -23℃~63℃

Relative Humidity maximum: 92%, non-condensing

Monitor Working -30℃~60℃, when 0°C below, the display needs

Temperature preheating.
Camera Working -25 ℃ ~80 ℃ , when 0°C below, please reduce
Temperature probe articulation.

8
2 Operation Steps

2.1 Take out the instrument

When removing the instrument from the case, be careful to not kink the cable or
scratch the camera lens

2.2 Boot preparation

Check to be sure the insertion tube is connected to the monitor, the SD card and
batteries are installed (one battery also works normally). Straighten the insertion
tube.

monitor
②
①
③

tube system

④
⑤

9
 * Connect the monitor to the insertion tube system; (1-5)

* Make sure the monitor us making contact with the upper portion of the handle
(1-5)

* Lock the button on the back of the monitor; (4)

* Install the SD card.

2.3 Operation

The DJ Series has10 levels of brightness adjustment. Press the light control
button to change the level. Slowly insert the tube to the inspected object. The
operation interface is as follows:

battery power image freezing measurement

brightness
TF card exposure full screen/zoom
temperature
special effect image rotation

white balance
preview mode

10
 2.4 Probe articulation control

According to the testing need, operate the joystick to control probe articulation.
The bending motion of the front probe is controlled by rotating the joystick.
During operation, if the joystick suddenly meets resistance, or there is any
abnormity, please immediately stop using. Adjust the joystick to the middle
position and carefully remove the insert tube from the tested equipment.

The articulation lock device is optional. When the probe is articulated to the
suitable position, if screw down this device, the articulation will be locked.

front view / side view switch

(available for dual lens model) articulation lock device

2.5 After use

Before you remove the insertion tube from the inspected object, please make
sure the probe is reset to straight. If the product is damaged due to improper
11
operation, the user is responsible for the damage. Turn off the power switch, put
the instrument into the portable case carefully, and put the tube into the case.

12
3 Image Capture and Operation

3.1 Photo/Video

① Short press “(9) photo/video button”;

② The image will freeze a frame, indicating a photo has been captured and
saved automatically. The saved file is named in the form of Date+No.
Such as:
20170725 001.JPEG
YTD No.

③ Long press “(9) photo/video button” for 2 seconds, it will start to record
video and the upper right corner of the screen will show the record time.
When finished, press “(9) photo/video button” for 2 seconds again to stop
the video. The file will be saved automatically.

3.2 Temperature indication & alarm (optional, not standard configuration)

13
 Temperature indicator is on the upper left of the screen. When the testing
temperature is 20℃~64℃, it indicates in green color. Orange alarm when the
probe temperature is 65℃~79℃; red alarm when above 80℃. For the protection
of the probe and camera, the monitor will shut off automatically.

3.3 Image special effects

In preview mode, press “(2) OK” button, select , which stands for standard

color mode. Press “(6) up” button or “(7) down” button, it changes to

negative film mode or black&white mode, in cyclic switch.

3.4 Exposure control

Press “(2) OK” button, select , which stands for exposure control mode.

Press “(6) up” button or “(7) down” button, it can switch the exposure level,
including 5 levels: -2/-1/0/+1/+2, in cyclic switch. According to the inspection
environment, users can adjust different exposure level, in order to get clearest
image.

3.5 Playback

In preview mode, press “(5) playback” button, it will change to image playback
mode. Press “(6) up” button or “(7) down” button to playbacks different images.
Press “(1) menu” button to pop up image delete menu, deleting images. Press
“(5)” button again, it will switch to video playback mode. Press “(2)” button to
playback video. Press “(2)” again to pause.

14
3.6 Measuring Function

In preview mode, press “(2) OK” button, select , which stands for measuring

prohibited function. Press “(6) up” button or “(7) down” button to swift to ,

start measuring function. Press “(6) up” button or “(7) down” button again to
close it.

3.7 Zoom in/out

In preview mode, press “(2) OK” button, select , which stands for zoom

in/out mode. Press “(6) up” button or “(7) down” button to adjust magnification
levels, including x1、x2、x4、x8 and two modes: full screen and full image, in
cyclic switch.

3.8 Language setting

In preview mode, press “(1) menu” button to enter menu dialog box. Select
“Language” menu by pressing “(6) up” or “(7) down” button. Then press “(2)
OK” button to pop up language option box, press “(6) up” or “(7) down” button
again to select and press “(2) OK” to confirm.

3.9 Date&Time setting

In preview mode, press “(1) menu” button to enter menu dialog box. Select
“Date&Time” menu by pressing “(6) up” or “(7) down” button. Then press “(2)
OK” button to pop up date&time setting dialog box, press “(4) return” button to
switch the format of date&time, press “(6) up” or “(7) down” button to set
date&time, press “(2) OK” to save the setting and return to the menu bar.

15
3.10 Auto shut off

In preview mode, press “(1) menu” button to enter menu dialog box. Select
“Auto shut off” menu by pressing “(6) up” or “(7) down” button. Then press “(2)
OK” button to pop up shut off time and function option box, press “(6) up” or “(7)
down” again to select shut off time and whether enable this function. Press
“(2) OK” to save the setting.

3.11 Date Stamp

In preview mode, press “(1) menu” button to enter menu dialog box. Select
“Date Stamp” menu by pressing “(6) up” or “(7) down” button. Then press “(2)
OK” button to pop up format and function option box, press “(6) up” or “(7) down”
again to select date stamp format and enable or turn off this function.

3.12 Formatting

In preview mode, press “(1) menu” button to enter menu dialog box. Select
“Format” menu by pressing “(6) up” or “(7) down” button. Then press “(2) OK”
button to pop up format option box, press “(6) up” or “(7) down” again to confirm
whether format the files in the TF card. Press “(2) OK” to complete the setting.

3.13 Factory Reset

In preview mode, press “(1) menu” button to enter menu dialog box. Select
“Factory Reset” menu by pressing “(6) up” or “(7) down” button. Then press
“(2) OK” button to pop up factory reset option box, press “(6) up” or “(7) down”
again to confirm reset all or not. Press “(2) OK” to complete the setting.

3.14 Firmware Update

The software will be continuously optimized and updated and the firmware
update function will be reserved in the menu. Users can place (.bin) new
16
 software files on the SD card (do not place it in folders or change bin file name).
Enter the setting interface, select firmware upgrade, it will be black screen. After
the screen indicator light goes out, turn off the monitor, reboot and enter new
system interface. Firmware update is finished.

4 Solution to Common Problems

Problem Reason Solution

no battery or power
Boot without reaction charge or install battery
shortage

Auto shutdown battery power shortage charge or change battery

system boot failure or remove the battery to re

Boot screen freezing
battery power shortage install and restart or charge

The image cannot be the capacity of TF card replace TF card or delete

recorded or found is not enough useless files

Image stuck system stuck shutdown and restart or reset

17