RoHS compliant

1550 nm Single-mode Transceiver, 37.5dB margin(150km)

Small Form Pluggable (SFP), with Diagnostic Monitoring
1.0625Gbd Fiber Channel/1.25 Gigabit Ethernet

Features
• RoHS compliant
• Compliant with IEEE802.3z Gigabit Ethernet
Standard
• Compliant with Fiber Channel 100-SM-LL-L
standard
• Compliant with SFF8472 diagnostic monitoring
interface
• Duplex LC connector
• Differential LVPECL inputs and outputs
• Single power supply 3.3V
• TTL signal detect indicator
• Hot Pluggable
• Class 1 laser product complies with EN 60825-1

Ordering Information
PART NUMBER INPUT/OUTPUT SIGNAL DETECT VOLTAGE TEMPERATURE
377.0189.00 AC/AC TTL 3.3V 0°C to 70 °C

Diagnostics
Parameter Range Accuracy Unit Calibration
o
Temperature -40 to 95 ±3 C
Voltage 0 to VCC ± 0.1 V
Bias Current 0 to 120 ±5 mA External
TX Power -1to +7 ± 3 dB dBm
RX Power -30 to –10 ± 3 dB dBm

Page 1 of 7 Website: http://www.datacom.ind.br

Version 1.0
Date: 03/16/2012
 RoHS compliant
1550 nm Single-mode Transceiver, 37.5dB margin(150km)
Small Form Pluggable (SFP), with Diagnostic Monitoring
1.0625Gbd Fiber Channel/1.25 Gigabit Ethernet

Absolute Maximum Ratings

PARAMETER SYMBOL MIN MAX UNITS NOTE
Storage Temperature TS −40 85 °C

Supply Voltage Vcc −0.5 4.0 V

Input Voltage VIN −0.5 Vcc V
Output Current
Io --- 50 mA
Operating Current IOP --- 400 mA
Recommended Operating Conditions
PARAMETER SYMBOL MIN MAX UNITS NOTE
Case Operating Temperature TC 0 70 ºC
Supply Voltage Vcc 3.1 3.5 V
Supply Current ITX + IRX --- 300 mA

Transmitter Electro-optical Characteristics

Vcc = 3.1 V to 3.5 V, TC = 0 °C to 70 °C
PARAMETER SYMBOL MIN TYP. MAX UNITS NOTE
Output Optical Power Pout +1.5 --- +6 dBm Average
9/125 µm fiber

Extinction Ratio ER 9 --- --- dB

Center Wavelength λC 1530 1550 1570 nm

Spectral Width (-20dB) ∆λ --- --- 0.6 nm

Output Eye Compliant with IEEE802.3z
Max. Pout TX-DISABLE Asserted POFF --- --- −45 dBm
Differential Input Voltage VDIFF 0.4 --- 2.0 V
Side Mode Suppression Ratio SMSR 30 --- --- dB

Rise/Fall Time (20−80%) Tr, f --- --- 260 ps

Total Jitter TJ --- --- 227 ps

Relative Intensity Noise RIN --- --- −120 dB/Hz

Page 2 of 7 Website: http://www.datacom.ind.br

Version 1.0
Date: 03/16/2012
 RoHS compliant
1550 nm Single-mode Transceiver, 37.5dB margin(150km)
Small Form Pluggable (SFP), with Diagnostic Monitoring
1.0625Gbd Fiber Channel/1.25 Gigabit Ethernet

Receiver Electro-optical Characteristics

Vcc = 3.1 V to 3.5 V, TC = 0 °C to 70 °C
PARAMETER SYMBOL MIN TYP. MAX UNITS NOTE

Optical Input Power -maximum PIN -9 --- --- dBm BER < 10−¹²

Optical Input Power –minimum PIN --- --- −36 dBm BER < 10−¹²
(Sensitivity)

Operating Center Wavelength λC 1260 --- 1610 nm

Data Output Rise, Fall Time Tr, f --- --- 0.35 ns

(20%-80%)

Optical Return Loss ORL 12 --- --- dB

Signal Detect-Asserted PA --- --- −36 dBm

Signal Detect-Deasserted PD −45 --- --- dBm

Differential Output Voltage VDIFF 0.5 --- 1.2 V

Receiver Loss of Signal Output RX_LOSL 0 --- 0.5 V

Voltage-Low

Receiver Loss of Signal Output RX_LOSH 2.4 --- VCC V

Voltage-High

Page 3 of 7 Website: http://www.datacom.ind.br

Version 1.0
Date: 03/16/2012
 RoHS compliant
1550 nm Single-mode Transceiver, 37.5dB margin(150km)
Small Form Pluggable (SFP), with Diagnostic Monitoring
1.0625Gbd Fiber Channel/1.25 Gigabit Ethernet

Block Diagram of Transceiver

ELECTRICAL SUBASSEMBLY

DATA
LD Driver
DATA/ & LASER
Fault Sense
TX_DISABLE
TX_FAULT

OPTICAL DUPLEX SC
(0)
SUB- RECEPTACLE
(1) ASSEMBLIES
M OD_DEF
(2)

DATA
POST-Amp RRE-
DATA/ & A MPLIFIER
LOS Detect IC
Photo
Diode
RX_LOS

TOP VIEW (Label side)

Transmitter Section
The transmitter section consists of a 1550 nm InGaAsP laser in an eye safe optical subassembly (OSA) which mates to the fiber
cable. The laser OSA is driven by a LD driver IC which converts differential input LVPECL logic signals into an analog laser
driving current.
TX_DISABLE
The TX_DISABLE signal is high (TTL logic “1”) to turn off the laser output. The laser will turn on when TX_DISABLE is low
(TTL logic “0”).
Receiver Section
The receiver utilizes an APD photodiode mounted together with a trans-impedance preamplifier IC in an OSA. This OSA is
connected to a circuit providing post-amplification quantization, and optical signal detection.
Receive Loss (RX_LOS)
The RX_LOS is high (logic “1”) when there is no incoming light from the companion transceiver. This signal is normally used by
the system for the diagnostic purpose. The signal is operated in LVTTL level..

Page 4 of 7 Website: http://www.datacom.ind.br

Version 1.0
Date: 03/16/2012
 RoHS compliant
1550 nm Single-mode Transceiver, 37.5dB margin(150km)
Small Form Pluggable (SFP), with Diagnostic Monitoring
1.0625Gbd Fiber Channel/1.25 Gigabit Ethernet

Dimensions

DIMENSIONS ARE IN MILLIMETERS

ALL DIMENSIONS ARE 0.2mm UNLESS OTHERWISE SPECIFIED
Unit: mm

Page 5 of 7 Website: http://www.datacom.ind.br

Version 1.0
Date: 03/16/2012
 RoHS compliant
1550 nm Single-mode Transceiver, 37.5dB margin(150km)
Small Form Pluggable (SFP), with Diagnostic Monitoring
1.0625Gbd Fiber Channel/1.25 Gigabit Ethernet

Pin Assignment
Pin-Out

PIN 11 PIN 20

PIN 10 PIN 1

Pin Signal Name Description

1 TGND Transmit Ground
2 TX_FAULT Transmit Fault
3 TX_DISABLE Transmit Disable
4 MOD_DEF (2) SDA Serial Data Signal
5 MOD_DEF (1) SCL Serial Clock Signal
6 MOD_DEF (0) TTL Low
7 RATE SELECT Open Circuit
8 RX_LOS Receiver Loss of Signal, TTL High, open collector
9 RGND Receiver Ground
10 RGND Receiver Ground
11 RGND Receiver Ground
12 RX− Receive Data Bar, Differential PECL, ac coupled
13 RX+ Receive Data, Differential PECL, ac coupled
14 RGND Receiver Ground
15 VCCR Receiver Power Supply
16 VCCT Transmitter Power Supply
17 TGND Transmitter Ground
18 TX+ Transmit Data, Differential PCEL, ac coupled
19 TX− Transmit Data Bar, Differential PCEL, ac coupled
20 TGND Transmitter Ground

Page 6 of 7 Website: http://www.datacom.ind.br

Version 1.0
Date: 03/16/2012
 RoHS compliant
1550 nm Single-mode Transceiver, 37.5dB margin(150km)
Small Form Pluggable (SFP), with Diagnostic Monitoring
1.0625Gbd Fiber Channel/1.25 Gigabit Ethernet

Eye Safety Mark

The series S i n g l e - m o d e transceiver is a class 1 laser

product. It complies with EN 60825-1 and FDA 21 CFR
1040.10 and 1040.11. In order to meet laser safety
requirements the transceiver shall be operated within the
Absolute Maximum Ratings.

Caution
All adjustments have been done at the factory before
the shipment of the devices. No maintenance and user
serviceable part is required. Tampering with and
modifying the performance of the device will result in
voided product warranty.

Note : All information contained in this document is subject to change without notice.

Page 7 of 7 Website: http://www.datacom.ind.br

Version 1.0
Date: 03/16/2012