Backlash Inglês

Backlash (engineering)
From Wikipedia, the free encyclopedia
Jump to: navigation, search
In mechanical engineering, backlash is purposeful clearance between mating components, sometimes

described as the amount of lost motion due to clearance or slackness when movement is reversed and
contact is re-established. For example, in a pair of gears, backlash is the amount of clearance between mated
gear teeth. This gap means that when a gear-train is reversed the driving gear must be turned a short distance
before all the driven gears start to rotate. A similar effect is the taking up of slack when a train starts to pull
away at the station and each car bumps as its link becomes tight. At low power outputs, backlash results in
inaccurate calculation from the small errors introduced at each change of direction; at large power outputs
backlash sends shocks through the whole system and can damage teeth and other components.
Backlash is an unavoidable property of all reversing mechanical couplings, and may or may not be
desirable, depending on the application. Some backlash is required to allow for lubrication, manufacturing
errors, deflection under load and differential expansion between the gears and the housing.
Gear couplings use backlash to allow for angular misalignment. The looseness of railroad car couplings is
another type of backlash which is deliberate; when starting a train from a dead stop, the engine starts each
following car rolling in turn as the couplings engage, instead of having to start all the cars at once, thus
efficiently overcoming the initial inertia and static friction with less force over a longer time.
Backlash is undesirable in precision positioning applications such as machine tool tables. It can be
minimized by tighter design features such as ballscrews instead of leadscrews, and by using preloaded
bearings. A preloaded bearing uses a spring or other compressive force to maintain bearing surfaces in
contact despite reversal of direction.
Math
Backlash is created when the tooth thickness of either gear is less than the tooth thickness of an ideal gear,
or the zero backlash tooth thickness. Additional backlash is created when the operating center distance of
the gear pair is less than that for two ideal gears. The total backlash is defined as:
where:
= total backlash,
= backlash due to tooth thickness modifications
= backlash due to operating center distance modifications
Backlash due to tooth thickness changes is typically measured along the pitch circle and is defined by:
where:
= tooth thickness on the pitch circle for ideal gearing (no backlash)
= actual tooth thickness
Backlash, measured on the pitch circle, due to operating center modifications is defined by:
bc = 2(Δc)tanφ
where:
= difference between actual and ideal operating center distances

= pressure angle
Standard practice is to make allowance for half the backlash in the tooth thickness of each gear. However,
there are applications where this may not be advisable. For example, if the pinion (the smaller of the two
gears) is too small or has few teeth, the engineer may elect to not modify the pinion teeth and instead, take
the total backlash out of the gear teeth.
Antibacklash gear designs

In certain applications, backlash is an undesirable characteristic and should be minimised; for example, a
radio tuning dial where one may make precise tuning movements both forwards and backwards. Specialised
gear designs allow this. One of the more common designs splits the gear into two gears, each half the
thickness of the original. One half of the gear is fixed to its shaft while the other half of the gear is allowed
to turn on the shaft, but pre-loaded in rotation by small coil springs that rotate the free gear relative to the
fixed gear. In this way, the spring tension rotates the free gear until all of the backlash in the system has
been taken out; the teeth of the fixed gear press against one side of the teeth of the pinion while the teeth of
the free gear press against the other side of the teeth on the pinion.
Loads smaller than the force of the springs do not compress the springs and with no gaps between the teeth
to be taken up, backlash is eliminated.
In mechanical computers a more complex solution is required, namely a frontlash gearbox.[1] This works by
turning slightly faster when the direction is reversed to 'use up' the backlash slack.

Backlash Inglês

Uploaded by

Copyright:

Available Formats

Backlash Inglês

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Backlash Inglês

Uploaded by

Copyright:

Available Formats

Backlash (engineering)

From Wikipedia, the free encyclopedia

Jump to: navigation, search

In mechanical engineering, backlash is purposeful clearance between mating components, sometimes

= difference between actual and ideal operating center distances

Antibacklash gear designs

You might also like