AL/AH

INSTALLATION INSTRUCTION
The illustrations in this instruction are used for easier understanding of the The owner’s manual contains assembly, use and maintenance instructions.
operation method of the product and the product structure. Please note there The vehicle must be assembled by an adult who has read and understands
may be differences between the pictures and the physical item. the instructions in this manual. Keep the packaging away from children and
dispose of all packaging before use.
In order to improve the quality, we may change part of the structure and Note:
For best performance use on flat, hard surfaces.
appearance of the product without an advance notice.
The following safety hazards may result in serious injury or death to the
！ Please read the instructions carefully before use, it will tell you the user of the vehicle:
right operation method and installation steps . Incorrect operation may • This product contains small parts that are for adult assembly only.
damage the product, or even hurt your child. Please keep this instruction


Keep small children away when assembling. Remove and dispose of all
ready and easy to find. protective material and poly bags before assembly. Be sure to remove all
packaging materials and parts from underneath the vehicle body.
• Battery posts, terminals and related accessories contain lead and lead
Preparation before installation: Power-on compounds (acids) chemicals known to the state of California to cause
cancer, reproductive harm, and are toxic and corrosive. Never open the
battery.
1 2 • Body parts such as hands, legs, hair and clothing can get caught in
moving parts. Never place a body part near a moving part or wear loose
clothing while using the vehicle. Always wear shoes when using the
vehicle.
•
This toy does not have brakes or any braking capability. Do not leave a
child unattended while using this toy or allow use of this toy in any
location that requires braking capability, as this couldresult in a roll away
or loss of control, which may cause serious injury or death.
• Using the vehicle near streets, motor vehicles, drop-offs such as: steps,
water (swimming pools) or other bodies of water, sloped surfaces, hills,
wet areas, flammable vapors, in alleys, at night or
in
the
dark
could
result

3 4 in
an
unexpected
accident.
Always
use

the
vehicle
in
a
safe,
secure

environment
with
continuous
adult
supervision.
·
Using
the
vehicle
in
unsafe
conditions
such
as
snow,
rain,
loose
dirt,

mud,
sand
or
fine
gravel
may
result
in
unexpected
action
such
as
tip
over

and
skidding,
and
damage
to
the
electrical
system
and
battery.
• Using the vehicle in an unsafe manner. Examples include but are not
[1] [2] limited to:
a. Pulling the vehicle with another vehicle or similar device
b. Allowing more than one rider
c. Pushing the user from the back
1.2: Please find and open the Charging hole cover as shown in figure. d. Traveling at an unsafe speed
3. Connect the terminal [1] and [2].
4. Close the Charging hole cover. Always use common sense and safe practices when using the vehicle.

1 2
 37 - 96 months
35
The following safety hazards may result in serious injury or death to the
user of the vehicle: Before using the vehicle the child should understand the vehicle controls
• Use of a battery or charger other than the supplied 12V and safety issues. They must also demonstrate the capability to handle the
rechargeable battery and charger may cause a fire or explosion. vehicle and operate its controls.
Only use the supplied 12V rechargeable battery and charger with It is the responsibility of the adult to educate the child and supervise the
the vehicle. vehicles use. Read the following safety warnings to any child using the
vehicle before riding.
• Using the 12V rechargeable battery and charger for
any other
product may result in overheating, fire or explosion. Never use
the 12V rechargeable battery and charger with another product.
• Explosive gases are created during charging. Charge the battery Never leave child unattended. Always supervise the child.
in a well ventilated area. Do not charge the battery near heat or Always sit in the seat when using the vehicle.
flammable materials. Keep your hands, hair and clothes away from moving parts.
Always wear shoes when using the vehicle.
• Contact between the positive and negative terminals may result
Only one rider is allowed on the vehicle at a time.
in fire or explosion. Avoid direct contact between the terminals. Children under 3 years of age cannot use the vehicle.
Picking up the battery by the wires or charger can cause damage Only drive on level ground.
to the battery and may result in a fire. Always pick up the battery Do not go near swimming pools or other bodies of water,
by it’s case or handles. drop-offs or up and down steep inclines.
• Liquids on the battery may cause fire or electric shock. Always Do not drive the vehicle into loose dirt, mud, sand or fine gravel.
keep all liquids away from the battery and keep the battery dry. Do not drive the vehicle on streets or near cars.
• Contact or exposure to battery leakage (lead acid) may cause Not to be used in traffic.
serious injury. If contact or exposure occurs immediately call
your physician. If the chemical is on the skin or in the eyes, flush
with cool water for 15 minutes. If the chemical was swallowed,

immediately
give
the
person
water
or
milk.
Do
not
give
water
or

milk
if
the
patient
is
vomiting
or
has
a
decreased
level
of

alertness.
Do
not
induce
vomiting. Park the vehicle indoors or cover it with a tarp to protect it from wet
• Battery posts, terminals and related accessories contain lead weather.
and lead compounds (acid), chemicals known to the State of Do not leave the vehicle in the sun for long periods of time or fading may
California to cause cancer, reproductive harm and are toxic and occur. Store in shade or cover with tarp.
corrosive. Never open the battery. Do not wash the vehicle with a hose.
• Tampering or modifying the electric circuit system may cause a Do not wash the vehicle with soap and water.
shock, fire or explosion and permanently damage the system. Pay attention while driving the vehicle, avoid falls or collisions causing
Exposed wiring, circuitry in the charger may cause electric shock. injury to the user or third parties.
Always keep the charger housing closed. Please check the component parts before using, and make regularly
examine the transformers or battery chargers for in the event of any
damage on the cord, plug, enclosure and other parts, the vehicle shall
not be used until the damage has been repaired, to avoid an accident.

3 4
 Damage to the battery may occur if it is allowed to drain completely.
Do not allow the battery to drain completely.
Check the battery and charger (supply cord, connector) for wear and
damage before charging. Do not charge the battery if damage has 1
occurred.
1 1 2

On average you will need to charge the battery between 8 and 12 hours.
Do not charge the batery for more than 20 hours. Failure to charge the
battery as directed could cause permanent damage to the battery and
void the warranty.
Only an adult who has read and understands the safety warnings should 3 4 4 1
handle, charge and recharge the battery.
C( Wheel) D( Bumper)
Specification
5 4 6 1
Name specification
E( Wheel Cover) G(Wind deflector)
Battery 12V 7Ah(6-FM-7（Ah）)*1/
12V 4.5Ah(6-FM-4.5（Ah）)*1

7 1 set 8 1
Motor Motor: 12V
H (Doors) I( Seat)
Suitable age 37-96 months

Max weight 35KG 1 10

9 1
Body size 1200*670*650MM J (Trailer guard and spade) K (Trailer guardrail)

Speed 3-6KM/h

11 1 12 1
Hours of use charging 8-12 hours，using 1 to 2 hours

L (Trailer guardrail - front part) M (Front axle assembly)

Input：110V~240V
Charger
Output: DC 12V 500mA-1000mA

Mainmaterial PP(polypropylene) and iron

13
1 14 1

N(Rear Axle) O (Trailer)

*The above parameters contain optional features, specific parameters
please refer to our samples.
 ④
15 2 16 2
M
P (Self-tapping screw) Q( M8 spanner) [1]

[1]
17
1 18 1 set
R(Charger) S (Door spindle)
①

19 1
(optional)
Z ①
T( Remote control ) Q

Step 1-2: Install the Front axle assembly

Place M onto the right place as shown in the figure, fix [1] axle to the
corresponding [3] holes follow the arrow direction. (attention: Z pass
through the [2] hole in the meantime). fix it with 2pcs ①(M8 nut) by
clockwise rotation[1]. then fix it with ④(M8 nut) by clockwise rotation.

N
1
M ②① ①②
④ 2

① N
①
Q

Step 1-1: Install the Front axle assembly

Q
A: Use the Q (M8 spanner) to loosen the①(M8 nut) from the M (Front axle
assembly) in a counterclockwise direction.
B. Use Q (M8 spanner) to loose ④(M8 nut) on the steering rod in a
anticlockwise direaction. Step 2: Install rear axle
1.Use Q (M8 spanner) to loose the 2pcs ②(nuts) from N (real axle) by
counterclockwise rotation, and take off the gasket.
2.Insert N (real axle) into the hole at real wheel seat, keep the same length
at left and right.
 1 A
②
A
③ ③
①
① Q
②
[2]
2 [1] ①①

Step 4: Install Steering Wheel

1. Remove the screw from the A (steering wheel) firstly.
① N N ① 2. Connect [1],[2] terminal first, place and fix A(steering wheel)on ①
② ② steering yoke as shown in figure.then insert the screw back to the A
E C C E (steering wheel).
S
S H
Q H
H
H

E E
② C C ②
① ①

Step 5:
Install the car door

First put H (door) on the corresponding place as shown in figure, push the S (Door
spindle) down to the door and car body.
*
NOTE: Pay attention to the installation direction, the right picture is a false
demonstration.

Step 3: Install the wheel K Step 6: Install guardrail

1. First use Q (M8 spanner) to loose ②（M8 nut） in a anticlockwise L Install the J (trailer guard
J and spade), L (trailer
direaction. Then take off ① gasket. Do not take off ③ Gasket.
guardrail - front part), K
2. Install the C(wheel), gasket , nut, H (wheel cover) on each front axle and (trailer guardrail) as
rear axle in turn as shown (attention: the left and right reserved length of shown in figure.
the rear axle should be consistent; all wheel's gear shaft should toward the
car body; align and press the buckle of the wheel cap with the grooves of
the wheel to fix it).
 Step 7: Install trailer Step 10: Bumper
D Insert D (bumper) to the
Insert the trailer guardrail corresponding hole on the
onto the trailer frame as car.
shown in figure (align the
10 hooks with the 10
groove and press it) .

Step 11: Install the

G Wind deflector
L
Insert G (Wind deflector)
R

L R

to the corresponding
place on the car.

R L
O
L R
O

1 2
Step 8: Install the
trailer
Align the 6 hole of O (trailer) with the 6 salient point on trailer frame and
press it hardly(Keep the arrow in the same direction, L to the L, R to the R).
make sure it has reached the designed position.
*Install the trailer in correct direction follow as figure 1.
Step 9: Install the seat
I
Put the I (seat) onto the
right place, then fix the I
(seat) with 2pcs P (self-
tapping screw) as shown
in figure.
P
 5.Do not mix old and new batteries. DO not mix alkaline, standard(carbon-
zinc),or rechargeable(nickel-cadmium) batteries.
1 6.Only an adult who has read and understood the safety warnings can
recharge the battery.

3. Instruction of door
TUNE

FM
U MP 3

START
STOP
lock switch
V- V+ High
MODE
Low

Push uo the door switch can

open the door.
+ - + -

LED Indicator

Use a screwdriver to remove the battery cover of the remote control, insert
two AAA 1.5V dry batteries in correct polarity. Close the battery cover and
fix it with the screw. (Battery replacement also according to the above
steps)

2.Matching the frequency of car and remote control

The remote control operation alaways prior to the manual control operation 2 3
U MP3
TUNE

.(The manual control won't work while operating remote control)

FM
START
STOP

1. Turn off the Power Switch on the car. MODE

V- V+ High
Low

2. Remove the battery cover on the Remote Control and put in 2 AAA
battery, the three LED indicators will flash.
3. Turn on the Power Switch on the car, when the LED indicators stop 5
flashing and 2 of them are on, matching successes.
4. Once the matching is made, there is no need to match code again only
if the battery is replaced.
5. The Remote Control will enter a sleep mode if not used for a long time
and the LED indicators will be off. Press any buttons to wake up the 4
Remote Control, and it can be used normally.

4. Instruction of each switch and function button

1. Control board
1.All batteries should be inserted in the correct polarity. 2. Music button: press the button to play music. long press the music button can
2.Non-rechargeable battery cannot be recharged increase the volume.
3.Take out and properly deal with the dead battery. To avoid injury, please 3. Horn button: press the button to play the horn.
long press the horn button can
keep kids away from the battery. reduce the volume.
4.The direct contact between the positive and negative terminals may result 4. Foot pedal switch: step on the foot pedal switch, the car will move forward,
in fire or explosion. Avoid direct connect between the terminals loosen the pedal, the car will stop.
5. Cup holder
5. Instruction of Control board 6. Operation guide for Manual control (forward,
11 12 13 Reverse ):
Driver sit down and fasten the seat belt. Long press the Start button, the
display will light up, the car will play a start sound (2-5 seconds). Press the
forward button and step on the foot switch, the car will move forward,
release the foot switch, the car will stop. Press the reverse button and step
1 TUNE U MP3
4 on the foot switch, the car will move backward, release the foot switch, the
car will stop. Long press the Start button again to turn off the power.
2 FM 5
START
STOP
7
V- V+ High Power on, by default, the forward speed is low speed, step on the foot
MODE
3 Low
6 switch, the car will move forward slowly, release the foot switch, the car
will stop. Press the high/low speed button can change to high speed, step
on the foot switch, the car will move forward faster, release the foot switch,
the car will stop. Press the high/low speed button again will change to low
7 8 9 10 speed.
* ONLY one speed for reverse, the high/low switch can not control the
1. FM radio search: In FM mode, press this botton will search the FM reverse speed. Everytime when power on, by default, the car will
channel. move forward in low speed.
2. FM station: Press this button to enter the FM mode。 8
3. Switch between Music, USB and AUX: Press this button to enter the
music mode. Can switch between different play modes( Music, USB, Resettable fuse: when
AUX) the current exceeds a certain rating,
4. Forward：Press forward botton, step on the foot switch the car will the recoverable fuse will automatically
move forward ,loosen the pedal the car will stop. cut off the power supply for 5-
5. Reverse：Press Reverse botton, step on the foot switch the car will 10seconds, then the current will be
move Reverse, loosen the pedal the car will stop. resupplied.
6. High/Low speed：Power on, by default, the forward speed is low speed,
press the High/low button can change to high speed, press this button
again, can change to low speed. For backward, there is only one speed, ! WARNING
the high/low button is invalid. RISK OF FIRE. Do not bypass fuse. This may overload and damage the
7.






/V- Previous /VOL down: short press to play the last channel, long electrical system. Replace only with original size and type.
press to lower the volume.
8. light switch: Power on, by default, the light is closed, press this button to 9. Reminder on using the trailer:
turn on the light, press again to turn off the light.
9.





/V+Next/ VOL up: Next channel / Volume up: short press to play the
next channel, long press to increase the volume. 5KG
10.
START/STOP/




: Long press to Turn on or turn off the power; When The Maximum load for
the music or radio is on, short press can stop it, short press again can trailer NOT exceeding 5 kg.
restart play it.
11. USB connector: Insert USB will play the music inside. Only MP3 mode
is supported.
12. Voltage display screen: The value on the display be used to determine
whether the battery needs to be charged.
13. AUX connector: Connect with other removable device to play audio file
valid.
 10

Trouble elimination methods

1. Is the fuse overloaded? 1.Yes, the fuse cuts off the power
2. The pedal switch connector is automatically by 5-20 seconds, then
restart; No, check next reason analysis
The motor good?
2.No, repair foot switch ; Yes, check next
3. The welding of motor electric
does not terminal is good?
reason analysis
rotate 3. No, weld the terminal wire ; Yes, check
TUNE

FM

MODE
V-
U MP3

START
STOP
V+ High
Low
4. The connector of the motor wire next reason analysis
is good？ 4.No, plug in the plug-in ; Yes, check next
5. Remove the motor's plug-in, reason analysis
change to connect battery directly, 5.Still no rotation, change the motor; If
then check if it rotate or not. rotates, it means driving circuit board
needs professional maintenance, please
contact with agent

1. Check the frontward/backward 1.No, replace the control board;

Only move Yes, check next reason analysis
switch, check the connector is
frontwards, 2.No, connect the line; Yes, it means
good or not by multimeter
or only move driving circuit board needs professional
2. Check the drive line cycle of
backwards maintenance, please contact with agent
frontward/bckwards is workable or
not?
1. Check the battery voltage is ok 1.No, charger the battery ; Yes it's ok,
or not. check next reason analysis
2. Connect the motor (including 2. No, check next reason analysis ; Yes, it
4 slow speed the driving gearbox) to the means driving circuit board needs
battery, then check the speed can professional maintenance, please
be accelerated or not. contact with agent
5
1. The battery connector fall off or 1. Yes, reconnect it, No, check next
The battery loosened. reason analysis
can not be 2. The charger has a slight heat 2.No, the charger is broken, replace it
recharged when it is charged
When car is 1. check the sound/light switch 1.No, replace the control board;
moving, the is ok or not. Yes, check next reason analysis
sound and 2. check the electric wire
2. No, reconnect; Yes, check next
light are connection (from battery to
useless headstock) is good or not? reason analysis
When battery power is low, please charge it immediately. The charging port When wheel 1. check the driving wheel can 1.Yes, lay the wheel to the ground; No,
is on the control board as shown in figure.
(Note: toys can not be operated running, the be rotated or not? checks the next reason analysis
in the charging state. Toys should be recharged by adult operation) . car does not 2. Check the gearbox, if any 2.Yes, replace the gear box; No,
move gear is damaged? checks the next reason analysis
1. Does the driver exceed the 1.Yes, should follow the instruction, the
Car is maximum load weight? car unsuitable for exceed maxweight;
unstable, 2. Does the driver ride on the No, check the next reason analysis
moving on rugged road? 2.Yes, should follow the instruction, ride
and off 3. Check the wheel can rotate on the flat cement road ; No, check the
freely? next reason analysis No,
Troubleshooting wheel and axle

17