P-Code Beschreibung SAE Beschreibung ECM

J2012 MG/Rover
P1000 PCM has been reset, no Permanent power supply Bosch M5.2.1 (PetrolV8)
diagnostic results interrupted
available
P1117 Engine Coolant
Temperature
RadiatorOutlet Sensor
Low Input
P1118 Engine Coolant
Temperature
RadiatorOutlet Sensor
High Input
P1129 O2 Sensors Swapped Front HO2 Sensors Bosch M5.2.1 (PetrolV8)
Bank to Bank(Sensor 1) transposed
P1140 Upstream oxygen sensor Siemens EMS 2000
1 - malfunction
P1160 Upstream oxygen sensor Siemens EMS 2000
2 - malfunction
P1170 Downstream Fuel Trim Front HO2 Sensor aged Bosch M5.2.1 (PetrolV8)
Malfunction (Bank1) - ATV adaption too lean /
too rich LH bank
P1171 System too Lean Bank A Additive injector adaptive
fuelling, lean limit
exceeded LH bank
P1172 System too Rich Bank A Additive injector adaptive
and Bank B fuelling, rich limit
exceeded LH bank
P1173 Downstream Fuel Trim Front HO2 Sensor aged Bosch M5.2.1 (PetrolV8)
Malfunction (Bank2) - ATV adaption too lean /
too rich RH bank
P1174 System too Lean Bank B Additive injector adaptive
fuelling, lean limit
exceeded RH bank
P1175 System too Rich Bank B Additive injector adaptive
fuelling, rich limit
exceeded RH bank
P1776 Electronic Automatic
Transmission (EAT)
Torque interface error
P1185 Upstream (pre-catalyst) MEMS3
oxygen sensorheater -
electrical fault
P1186 Upstream (pre-catalyst) MEMS3
oxygen sensorheater -
electrical fault
P1188 Fuelling Trim Adaption
Bank A
P1189 Fuelling Trim Adaption
Bank B
P1191 Downstream MEMS3
(post-catalyst) oxygen
sensor heater - electrical
fault
P1192 Downstream MEMS3
(post-catalyst) oxygen
sensor heater - electrical
fault
P1195 Pressure regulator valve Bosch EDC15C (M47R
malfunction diesel engine)
P1230 Fuel Pump Relay Fuel pump relay open Siemens EMS 2000
Malfunction circuit
P1231 Fuel Pump Relay Circuit Fuel pump relay short Siemens EMS 2000
Low circuit to earth
P1232 Fuel Pump Relay Circuit Fuel pump relay short Siemens EMS 2000
High circuit to batteryvoltage
P1255 Low pressure fuel sensorBosch EDC15C (M47R
malfunction diesel engine)
P1300 Misfire Detected Catalyst damaging level Bosch M5.2.1 (Petrol V8)
Sufficient to Cause of misfire on morethan
Catalyst Damage one cylinder
P1301 No description Catalyst damaging level Bosch M5.2.1 (Petrol V8)
of misfire detectedon
cylinder No.1
P1302 No description Catalyst damaging level Bosch M5.2.1 (Petrol V8)
of misfire detectedon
cylinder No. 2
P1303 No description Catalyst damaging level Bosch M5.2.1 (Petrol V8)
of misfire detectedon
cylinder No. 3
P1304 No description Catalyst damaging level Bosch M5.2.1 (Petrol V8)
of misfire detectedon
cylinder No.4
P1305 No description Catalyst damaging level Bosch M5.2.1 (Petrol V8)
of misfire detectedon
cylinder No.5
P1306 No description Catalyst damaging level Bosch M5.2.1 (Petrol V8)
of misfire detectedon
cylinder No.6
P1307 No description Catalyst damaging level Bosch M5.2.1 (Petrol V8)
of misfire detectedon
cylinder No.7
P1308 No description Catalyst damaging level Bosch M5.2.1 (Petrol V8)
of misfire detectedon
cylinder No. 8
P1316 Cylinder block - misfire MEMS3
causing increased
emissions
P1319 Cylinder banks misfire at Siemens EMS 2000
low fuel level
P1320 CKP sensor - flywheel Siemens EMS 2000
adaption for misfire
detection, adaption limit
P1321 CKP sensor - flywheel Siemens EMS 2000
adaption for misfire
detection, tooth error
P1402 Downstream oxygen Siemens EMS 2000
sensor - malfunction
P1412 Secondary Air Injection
SystemMalfunction
(Bank 1)
P1413 Secondary Air Injection
System Air Control Valve
Always Open (Bank 1)
P1414 Secondary Air Injection
System Low Air Flow
(Bank 1)
P1415 Secondary Air Injection
SystemMalfunction
(Bank 2)
P1416 Secondary Air Injection
System Air Control Valve
Always Open (Bank 2)
P1417 Secondary Air Injection
System Low Air Flow
(Bank 2)
P1450 Evaporative Emission
Control SystemLeakage
Pump Circuit Plausibility
P1451 Evaporative Emission
Control SystemLeakage
Pump Circuit High
P1452 Evaporative Emission
Control SystemLeakage
Pump Circuit Low
Current
P1453 Evaporative Emission
Control SystemLeakage
Pump Circuit High
Current
P1470 Varaible intake balance Siemens EMS 2000
valve always open
P1471 Variable intake balance Siemens EMS 2000
valve always closed
P1472 Variable intake butterfly Siemens EMS 2000
(power) valves - always
open
P1473 Variable intake butterfly Siemens EMS 2000
(power) valves - always
closed
P1474 Variable intake balance Siemens EMS 2000
valve - electrical short to
battery
P1475 Variable intake balance Siemens EMS 2000
valve - electrical short to
earth or open circuit
P1476 Variable intake butterfly Siemens EMS 2000
(power) valves -
electrical short to battery
P1477 Variable intake butterfly Siemens EMS 2000
(power) valves -
electrical short to earth
or open circuit
P1506 Idle air control (IAC) MEMS3
valve stepper motor
drive - circuit fault
P1507 Idle air control (IAC) MEMS3
valve stepper motor
drive - circuit fault
P1508 Idle air control (IAC) MEMS3
valve stepper motor
drive - circuit fault
P1509 IACV Opening Coil Open circuit or short Bosch M5.2.1 (PetrolV8)
Malfunction circuit to battery supply
or earth - opening
windings
P1510 IACV - Opening Coil
Circuit Malfunction
P1513 IACV - opening Coil
Circuit Low
P1514 IACV Opening Coil
Circuit High
P1535 Air Conditioning ATC requested when not
Compressor in standby mode
RequestMalfunction
P1536 Air Conditioning ATC compressor clutch Bosch M5.2.1 (PetrolV8)
Compressor relay open circuit
RequestRange /
Performance
P1537 Air Conditioning ATC compressor clutch Siemens EMS 2000
Compressor Request relay short to earth
LowInput
P1538 Air Conditioning Air conditioning clutch Siemens EMS 2000
Compressor Request relay - short tobattery
HighInput voltage
P1550 IACV - Closing Coil Open circuit or short Bosch M5.2.1 (PetrolV8)
Malfunction circuit to battery supply
or earth - closing
windings
P1551 IACV - Closing Coil
Circuit Malfunction
P1552 IACV - Closing Coil
Circuit Low
P1553 IACV - Closing Coil
Circuit High
P1565 Cruise control (interface Siemens EMS 2000
ECU) - short circuit to
battery voltage
P1566 Cruise control (interface Siemens EMS 2000
ECU) - short circuit to
earth or open circuit
P1590 ABS Rough Road Signal Hardware is OK but the Bosch M5.2.1 (PetrolV8)
Circuit Malfunction SLABS ECU is sending
an error signal
P1591 ABS Rough Road Signal Signal from SLABS ECU Bosch M5.2.1 (PetrolV8)
Circuit Low shorted to ground or
open circuit
P1592 ABS Rough Road Signal Signal from SLABS ECU Bosch M5.2.1 (PetrolV8)
Circuit High shorted to batteryvoltage
P1610 - Main relay - short to Siemens EMS 2000
battery voltage
P1611 - Main relay - short to Siemens EMS 2000
earth or open circuit
P1640 - CAN Bus - CAN MEMS3
message failure
P1641 - CAN Bus - bus failure Siemens EMS 2000
P1645 - ASC1 (message from Siemens EMS 2000
ASR unit) - framemissing
P1646 - CAN Bus - automatic Siemens EMS 2000
transmission message
fault
P1647 - CAN Bus - message Siemens EMS 2000
from instrument
packfault
P1663 Throttle Angle / Torque SLABS HDC link open Bosch M5.2.1 (PetrolV8)
Signal Circuit circuit
Malfunction
P1664 Throttle Angle / Torque SLABS HDC link short to Bosch M5.2.1 (PetrolV8)
Signal Circuit Low ground
P1665 Throttle Angle / Torque SLABS HDC link short Bosch M5.2.1 (Petrol V8)
Signal Circuit High circuit to batteryvoltage
P1666 Engine Anti-Theft Signal Alarm ECU - security Siemens EMS 2000
Circuit Malfunction code not received
P1667 Engine Anti-Theft Signal Serial link short to earth Bosch M5.2.1 (Petrol V8)
Circuit Low
P1668 Engine Anti-Theft Signal Serial link open circuit Bosch M5.2.1 (Petrol V8)
Circuit High
P1669 Engine Control Module
Cooling Fan
CircuitMalfunction
P1670 Engine Control Module
Cooling Fan CircuitLow
P1671 Engine Control Module
Cooling Fan CircuitHigh
P1672 Engine Anti-Theft Signal Alarm ECU - security Siemens EMS 2000
Wrong CodeReceived code incorrect
P1673 Engine Anti-Theft Signal New ECM fitted Bosch M5.2.1 (Petrol V8)
New EngineControl
Module Not Configured
P1674 Engine Anti-Theft Signal No code ECM, valid Bosch M5.2.1 (Petrol V8)
code received
P1675 Condensor Fan Circuit
Malfunction
P1700 Transfer Box Indicated Low range signal Bosch M5.2.1 (Petrol V8)
Range - Performance implausible
P1701 Transfer Box has
signalled a fault
condition to the Engine
Control Module
P1702 Transfer Box - Signal
Line
CommunicationFrame
Error
P1703 Transfer box link - signal
line permanentlyat 12V
or open circuit
P1708 Transfer box link - signal
line permanentlyat
ground
P1775 - CAN Bus - Automatic MEMS3
gearbox GIU MIL
request
P1776 Transmission Control EAT Torque interface Bosch M5.2.1 (Petrol V8)
System Torque Interface error
Malfunction
P1785 - Steptronic EM-CVT ratio MEMS3
control motor - drive over
temperature
P1787 - Steptronic EM-CVT ratio MEMS3
control motor - open
circuit
P1788 - Steptronic EM-CVT ratio MEMS3
control motor - ratio
control motor over
current
P1810 - Steptronic EM-CVT MEMS3
PRNDM LED module -
circuit fault
P1815 - Steptronic EM-CVT MEMS3
Manual +/- switch - gear
shift up signal fault
P1816 - Steptronic EM-CVT MEMS3
Manual +/- switch - gear
shift down signal fault
P1830 - Steptronic EM-CVT MEMS3
PWM link from ECM
toGIU - circuit fault
P1831 - Steptronic EM-CVT MEMS3
PWM link from ECM
toGIU - circuit fault
P1836 - Steptronic EM-CVT MEMS3
serial link from GIU
toECM - no serial data
transmitted
P1837 - PWM link from ECM to MEMS3
instrument pack - circuit
fault
P1838 - PWM link from ECM to
instrument pack - circuit
fault
●