Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 19 views

    19.2.1 Packet Tracer - Configure GRE

    Uploaded by

    Billups

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd

    19.2.1 Packet Tracer - Configure GRE

    Uploaded by

    Billups
    19 views2 pages

    Copyright

    © © All Rights Reserved

    Available Formats

    DOCX, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    19 views2 pages

    19.2.1 Packet Tracer - Configure GRE

    Uploaded by

    Billups

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    of 2

    Packet Tracer - Configure GRE

    Addressing Table
    Device Interface IP Address Subnet Mask Default Gateway

    RA G0/0 192.168.1.1 255.255.255.0 N/A


    RA
    S0/0/0 64.103.211.2 255.255.255.252 N/A

    RA
    Tunnel 0 10.10.10.1 255.255.255.252 N/A

    RB G0/0 192.168.2.1 255.255.255.0 N/A


    RB
    S0/0/0 209.165.122.2 255.255.255.252 N/A

    RB
    Tunnel 0 10.10.10.2 255.255.255.252 N/A

    PCA NIC 192.168.1.2 255.255.255.0 192.168.1.1


    PCB NIC 192.168.2.2 255.255.255.0 192.168.2.1

    Objectives
    Part 1: Verify Router Connectivity
    Part 2: Configure GRE Tunnels
    Part 3: Verify PC Connectivity

    Scenario
    You are the network administrator for a company which wants to set up a GRE tunnel to a remote office. Both
    networks are locally configured. You need configure the tunnel and static routes.

    Instructions

    Part 1: Verify Router Connectivity


    Step 1: Ping RA from RB.
    a. Use the show ip interface brief command on RA to determine the IP address of the S0/0/0 port.
    b. From RB ping the IP S0/0/0 address of RA.

    Step 2: Ping PCA from PCB.


    Attempt to ping the IP address of PCA from PCB. We will repeat this test after configuring the GRE tunnel.
    What were the ping results? Explain.
    Type your answers here.

     2019 - 2020 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 1 of 2 www.netacad.com
    Packet Tracer - Configure GRE

    Part 2: Configure GRE Tunnels


    Step 1: Configure the Tunnel 0 interface of RA.
    a. Enter into the configuration mode for RA Tunnel 0.
    RA(config)# interface tunnel 0
    b. Set the IP address as indicated in the Addressing Table.
    RA(config-if)# ip address 10.10.10.1 255.255.255.252
    c. Set the source and destination for the endpoints of Tunnel 0.
    RA(config-if)# tunnel source s0/0/0
    RA(config-if)# tunnel destination 209.165.122.2
    d. Configure Tunnel 0 to convey IP traffic over GRE.
    RA(config-if)# tunnel mode gre ip
    e. The Tunnel 0 interface should already be active. In the event that it is not, treat it like any other interface.
    RA(config-if)# no shutdown

    Step 2: Configure the Tunnel 0 interface of RB.


    Repeat Steps 1a – e with RB. Be sure to change the IP addressing as appropriate.

    Step 3: Configure a route for private IP traffic.


    Establish a route between the 192.168.X.X networks using the 10.10.10.0/30 network as the destination.
    RA(config)# ip route 192.168.2.0 255.255.255.0 10.10.10.2
    RB(config)# ip route 192.168.1.0 255.255.255.0 10.10.10.1

    Part 3: Verify Router Connectivity


    Step 1: Ping PCA from PCB.
    Attempt to ping the IP address of PCA from PCB. The ping should be successful.

    Step 2: Trace the path from PCA to PCB.


    Attempt to trace the path from PCA to PCB. Note the lack of public IP addresses in the output.
    End of document

     2019 - 2020 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 2 of 2 www.netacad.com

    You might also like