ZXA10 C6XX V1.1.0 Commissioning and General Operation Maintenance Guide V2.0

ZXA10 C6XX V1.1.
0
Commissioning and General
Operation Maintenance Guide V2.0
Confidential▲
LEGAL INFORMATION
By accepting this certain document of ZTE CORPORATION you agree to the following terms. If you do not
agree to the following terms, please notice that you are not allowed to use this document.
Copyright © 2019 ZTE CORPORATION. Any rights not expressly granted herein are reserved. This document
contains proprietary information of ZTE CORPORATION. Any reproduction, transfer, distribution, use or
disclosure of this document or any portion of this document, in any form by any means, without the prior written
consent of ZTE CORPORATION is prohibited.
and are registered trademarks of ZTE CORPORATION. ZTE’s company name,

logo and product names referenced herein are either trademarks or registered trademarks of ZTE
CORPORATION. Other product and company names mentioned herein may be trademarks or trade names of
their respective owners. Without the prior written consent of ZTE CORPORATION or the third party owner
thereof, anyone’s access to this document should not be construed as granting, by implication, estopped or
otherwise, any license or right to use any marks appearing in the document.
The design of this product complies with requirements of environmental protection and personal security. This
product shall be stored, used or discarded in accordance with product manual, relevant contract or laws and
regulations in relevant country (countries).
This document is provided “as is” and “as available”. Information contained in this document is subject to
continuous update without further notice due to improvement and update of ZTE CORPORATION’s products
and technologies.
ZTE CORPORATION
Address: NO. 55
Hi-tech Road South
ShenZhen
P.R.China
518057
Website: http://dms.zte.com.cn (Technical Support)
Email: TSM.Aftersales@zte.com.cn
ZTE Confidential Proprietary © 2019 ZTE Corporation. All rights reserved. Page 1
Confidential▲
Revision History
Product Version Document Version Serial Number Reason for Revision
First published
Author
Prepared
Document Version Date Reviewed by Approved by
by
Lin
1.2 2019-1-23
Guoxin
Confidential▲
Applicable to: Commissioning maintenance personnel
Proposal: Before reading this document, it is recommended to understand the following

knowledge and skills
SEQ Knowledge and skills Reference material
1
2
3
Follow-up document: After read this document, you may need the following information
SEQ Reference Material Information
1
2
3
Confidential▲
Contents
1 OVERVIEW ...................................................................................................................... 10
2 RELATED DATA PLANNING ........................................................................................ 10
2.1 UPLINK PORT CONFIGURATION REQUIREMENTS ........................................... 10
2.2 GPON/XGPON SERVICE PLANNING...................................................................11
2.2.1 GPON/XGPON ONU SERVICE SCENARIO REQUIREMENTS................... 11
2.2.2 GPON/XGPON BASIC SERVICE SCENARIO CONFIGURATION

FLOWCHART................................................................................................ 11
2.3 EPON/10EPON SERVICE PLANNING ..................................................................12
2.3.1 EPON/10G EPON SERVICE SCENARIO REQUIREMENTS ........................ 12
2.3.2 EPON/10G EPON BASIC SERVICE SCENARIO CONFIGURATION

FLOWCHART................................................................................................ 13
2.4 PLANNING OF COMMISSIONING DATA ........................................................... 15
2.4.1 OLT DATA PLANNING ................................................................................ 15
2.4.2 GPON/XPON ONU DATA PLANNING ...................................................... 15
2.4.3 EPON/10GEON ONU DATA PLANNING................................................... 15
3 GLOBAL DATA CONFIGURATION FOR C600 COMMISSIONING ......................... 16
3.1 CONNECT VIA THE SERIAL PORT AND INTRODUCE PORTS ON THE
PANEL OF SWITCHING & CONTROL CARD .................................................... 16
3.2 CREATE USER NAME / PASSWORD FOR C6XX ................................................. 17
3.2.1 CREATE USER NAME / PASSWORD OF LOCAL AUTHENTICATION...... 17
3.2.2 CREATE USER NAME / PASSWORD OF RADIUS AUTHENTICATION .... 18
3.2.3 CONFIGURE USER NAME / PASSWORD OF TACACS AUTHENTICATION19
3.3 ADD PHYSICAL CONFIGURATION ...................................................................... 20
3.4 CONFIGURE OUT-BAND / IN-BAND MANAGEMENT ADDRESS .................... 21
Confidential▲
3.4.1 CONFIGURE OUT-BAND MANAGEMENT ADDRESS .............................. 21
3.4.2 CONFIGURE IN-BAND MANAGEMENT ADDRESS AND ROUTE ........... 22
3.5 CREATE LACP SMARTGROUP .............................................................................. 23
3.5.1 ADD THE IN-BAND MANAGEMENT VLAN TO THE UPLINK PORT ....... 23
3.5.2 CREATE SMARTGROUP AND ADD TO VLAN .......................................... 23
3.5.3 CREATE DYNAMIC SMARTGROUP ........................................................... 23
3.6 CREATE UAPS PROTECTION GROUPS................................................................ 25
3.6.1 CONFIGURE MASTER / SLAVE PROTECTION RELATIONSHIP ............... 25
3.6.2 CONFIGURE UAPS PROTECTION SWITCHING TIME .............................. 26
3.6.3 SET THE TRIGGERING CONDITION FOR UAPS PROTECTION SWITCHING

26
3.6.4 CONFIGURE UAPS PROTECTION FOR SMARTGROUP ........................... 27
3.7 ADD C600 NE ON EMS ........................................................................................ 29
3.8 MULTICAST GLOBAL CONFIGURATION ............................................................ 30
3.8.1 CONFIGURE THE SLAVE SWITCH AND CONFIGURE MULTICAST GROUP

30
3.8.2 CONFIGURE MULTICAST SOURCE PORT AND RECEIVE PORT.............. 30
3.8.3 CONFIGURE MULTICAST TO RETRIEVE PACKETS BASED ON VLAN .... 31
3.9 CONFIGURE ACL ...................................................................................................31
3.9.1 CREATE ACL AND RULE.............................................................................. 31
3.9.2 BIND ACL ..................................................................................................... 32
3.9.3 VIEW ALL ACL ENTRIES BOUND ............................................................... 32
3.10 OTHER GLOBAL CONFIGURATIONS...................................................................33
3.10.1 MODIFY THE SYSTEM TIMEZONE AND TIME ........................................ 33
3.10.2 CONFIGURE THE NTP CONNECTION SERVER ....................................... 33
3.10.3 SET TELNET AND SERIAL PORT TIMEOUT TIME .................................... 33
3.10.4 METHOD TO MODIFY THREE-PACKET LIMIT ......................................... 34
Confidential▲
3.10.5 SET PORT DELAY DOWN .......................................................................... 34
4 GPON/XGPON ONU COMMISSIONING ...................................................................35
4.1 CREATE ONU TYPE PROFILE ................................................................................ 35
4.1.1 CREATE GENERAL ONU PROFILE .............................................................. 35
4.1.2 SPECIAL CONFIGURATIONS OF ONU PROFILE ....................................... 36
4.2 CREATE GPON TCONT BANDWIDTH PROFILE ................................................. 38
4.3 CREATE VPORT OR SERVICE-PORT RATE-LIMIT BANDWIDTH PROFILE ....... 39
4.4 CONFIGURE VOIP-RELATED PROFILES .............................................................. 39
4.4.1 CREATE IP PROFILE ..................................................................................... 39
4.4.2 CREATE VLAN PROFILE .............................................................................. 40
4.4.3 CONFIGURE VOIP PROTOCOL PROFILE ................................................... 40
4.5 ADD SERVICE VLAN TO OLT UPLINK PORT....................................................... 42
4.5.1 SINGLE-PORT UPLINKING STATES ........................................................... 42
4.5.2 SMARTGROUP UPLINKING STATES.......................................................... 42
4.6 CONFIGURE ONU AUTHENTICATION AND SERVICES ..................................... 42
4.6.1 ENABLE THE PON PORT ............................................................................ 42
4.6.2 CONFIGURE AUTHENTICATED ONUS ...................................................... 42
4.6.3 CONFIGURE TCONT AND GEMPORT SERVICE FLOWS .......................... 43
4.6.4 HGU CONFIGURES SERVICE DATA UNDER REMOTE MANAGEMENT .43
4.6.5 SFU CONFIGURES SERVICE DATA UNDER REMOTE MANAGEMENT...44
4.6.6 CONFIGURE SERVICE-PORT ...................................................................... 46
4.6.7 CONFIGURE SERVICE-PORT OR VPORT RATE-LIMIT ............................. 47
4.6.8 VPORT AND GEMPORT MAPPING CONFIGURATION............................ 47
5 EPON/10G EPON ONU COMMISSIONING ............................................................... 49
5.1 CONFIGURE EPON AUTHENTICATION MODE .................................................. 49
5.2 CREATE ONU TYPE PROFILE ................................................................................ 50

Confidential▲
5.3 CREATE BANDWIDTH RATE-LIMIT PROFILE ...................................................... 51
5.3.1 EPON/10G EPON RATE-LIMIT ...................................................................51
5.3.2 CONFIGURE UPSTREAM SLA RATE-LIMIT PROFILE ................................ 52
5.3.3 CONFIGURE DOWNSTREAM VPORT OR SERVICE-PORT ATE-LIMIT

PROFILE ........................................................................................................ 52
5.4 OLT UPLINK PORT ADDS SERVICE VLAN........................................................... 53
5.5 CHOOSE 10G EPON WORKING MODE .............................................................. 53
5.6 CONFIGURE ONU AUTHENTICATION AND SERVICE DATA ............................ 53
5.6.1 CONFIGURE ONU AUTHENTICATION ...................................................... 53
5.6.2 CONFIGURE SERVICES UNDER ONU INTERFACE ...................................54
5.6.3 CONFIGURE HGU REMOTE MANAGEMENT ............................................ 54
5.6.4 CONFIGURE SFU REMOTE MANAGEMENT ............................................. 54
5.6.5 CONFIGURE SERVICE-PORT ...................................................................... 55
5.6.6 EPON ONU DOWNSTREAM RATE-LIMIT ................................................. 56
6 CONFIGURE PORT LOCATION .................................................................................... 56
6.1 CONFIGURE PPPOE PLUS .................................................................................... 56
6.2 CONFIGURE DHCP OPTION82 ............................................................................ 57
6.3 CONFIGURE REMOTE ID ...................................................................................... 58
7 GENERAL MAINTENANCE OPERATIONS .................................................................59
7.1 SHOW CONFIGURATION INFORMATION ......................................................... 59
7.1.1 QUERY UN-AUTHENTICATED ONU .......................................................... 59
7.1.2 QUERY THE CONFIGURATION UNDER THE PON PORT (METHOD 1) .60
7.1.3 QUERY THE CONFIGURATION UNDER THE PON PORT (METHOD 2) .60
7.1.4 QUERY ONU VIRTUAL INTERFACE AND REMOTE MANAGEMENT

CONFIGURATION........................................................................................ 61
7.1.5 VIEW VPORT INTERFACE CONFIGURATION ........................................... 61
Confidential▲
7.1.6 QUERY AND SHOW SERVICE-PORT CONFIGURATION ACCORDING TO

ONU .............................................................................................................. 63
7.1.7 QUERY AND SHOW SERVICE-PORT CONFIGURATION ACCORDING TO

VPORT .......................................................................................................... 63
7.1.8 VIEW OUT-BAND MANAGEMENT CONFIGURATION ............................ 63
7.1.9 VIEW VLAN INTERFACE CONFIGURATION .............................................. 64
7.1.10 VIEW ONU VEIP VLAN CONFIGURATION .............................................. 64
7.1.11 BATCHED CREATE AND SHOW VLAN..................................................... 64
7.2 SHOW ALARMS AND LOGS ................................................................................ 64
7.2.1 VIEW CURRENT ALARMS ........................................................................... 64
7.2.2 VIEW HISTORY ALARMS ............................................................................ 65
7.2.3 VIEW ALARM RECORDS ............................................................................. 65
7.2.4 VIEW OPERATION RECORDS ..................................................................... 66
7.2.5 VIEW SNMP LOG INFORMATION ............................................................. 66
7.2.6 CONFIGURE SYSLOG REPORTING ............................................................ 67
7.3 VIEW EQUIPMENT INFORMATION ..................................................................... 67
7.3.1 VIEW OPTICAL MODULE INFORMATION ................................................ 67
7.3.2 VIEW CARD SOFTWARE / HARDWARE INFORMATION OF THE

EQUIPMENT .................................................................................................68
7.3.3 SHOW MAC ADDRESS OF THE UPLINK PORT ........................................ 68
7.3.4 SHOW ROUTE INFORMATION ..................................................................69
7.3.5 SHOW PORT OPTICAL POWER INDEX ..................................................... 69
7.3.6 SHOW STATUS OF ALL INTERFACES ........................................................ 69
7.3.7 SHOW CPU QUEUE MESSAGE STATISTICS .............................................. 70
7.3.8 SHOW PROTOCOL MESSAGE STATISTICS ENTERING THE MAIN

CONTROL’S CPU ...................................................................................... 70
7.3.9 SHOW PROTOCOL MESSAGE STATISTICS ENTERING THE LINE CARD’S

CPU ............................................................................................................... 72
Confidential▲
7.4 PERFORMANCE STATISTICS ................................................................................ 73
7.4.1 SHOW ETHERNET PORT PERFORMANCE ................................................ 73
7.4.2 CREATE VPORT FLOW STATISTICS ........................................................... 74
7.5 EQUIPMENT OPERATIONS .................................................................................. 74
7.5.1 RESET CARD.................................................................................................74
7.5.2 RESTART THE SYSTEM................................................................................ 75
7.5.3 SHOW TEMPERATURE ................................................................................ 75
7.5.4 SHOW BROADCAST /UNKNOWNCAST/MULTICAST PACKET

CONFIGURATION........................................................................................ 76
7.5.5 DETECT ROGUE ONU ................................................................................. 76
7.5.6 SHOW INFORMATION OF THE LOGIN TERMINAL .................................77
7.5.7 METHOD TO CONNECT THE ODB PORT ................................................. 77
7.5.8 DISTRIBUTE AND QUERY TCONT BANDWIDTH ..................................... 79
7.5.9 MODIFY THE LENGTH OF OPTICAL FIBER ............................................... 79
7.6 REMOTE CPU PACKET CAPTURING .................................................................... 79
7.6.1 CPU PACKET CAPTURING FUNCTION BASED ON SWITCHING &

CONTROL CARD ......................................................................................... 79
7.6.2 CPU PACKET CAPTURING FUNCTION BASED ON LINE CARDS............ 80
Confidential▲
1 Overview
The ZXA10 C6xxV1.1.0 version is not greatly different from ZXA10 C600V1.0.0 in
terms of equipment software commissioning and configuration, but just some new
functions are added. However, apart from C600 version, the ZXA10 C6xxV1.1.0 version
packages also integrate versions of such equipment as C620, C650, C680 and so on, and
add part of new maintenance diagnosis functions. To facilitate use of ZXA10 C6xxV1.1.0
version, and meet on-site commissioning and maintenance requirements, this document
is mainly to modify and supplement based on original ZXA10 C600V1.0.0 Version
Commissioning and General Operation Summary.
Following contents are comprised in this document:
1. Related data planning, including: uplink configuration planning,
GPON/XGPON/EPON/10GEPON service planning and data planning, etc.;
2. C600 global data configuration, including: serial port configuration, configuration of
multiple C6xx user name / password authentication modes, other global configuration
data needed by C6xx commissioning and so on;
3. GPON/XGPON/EPON/10GEPON service commissioning;
4. C6xx general maintenance operations.
2 Related Data Planning
2.1 Uplink Port Configuration Requirements
At present, uplink ports of C600 is provided by uplink cards, while the switching &
control card SFUL doesn’t provide uplink ports; physical type supports optical port,
and it is 10G by default; configuration rate supports 1000M and 10G (decided by port
property). LACP aggregation is supported between ports, and same-card and span-card
LACP smartgroup are supported. Span-card aggregation is recommended. At present,
uplink ports can also configure UAPS protection groups, and support to configure UAPS
protection on the same card or span-card.
Confidential▲
2.2 GPON/XGPON Service Planning
2.2.1 GPON/XGPON ONU service scenario requirements
Generally, common scenarios of GPON/XGPON service comprises 4 kinds of

services: ITMS management, VOIP, IPTV and broadband service. Each service
configuration corresponds to different CVLANs. And for 4 kinds of services, following 3
scenarios can be used:
1) 1 TCONT and 1 GEMPORT map 1 VPORT, and configure 4 service-ports;
2) 1 TCONT corresponds to 4 GEMPORTs to map 1 VPORT, and configure 4 service-

ports;
3) 4 TCONT corresponds to 4 GEMPORTs to map 1 VPORT, and configure 4 service-

ports.
2.2.2 GPON/XGPON basic service scenario configuration flowchart
The basic service configuration flowchart is shown as below. The flowchart is

applicable to all ONU types. For different ONU types, there may differ inside each step,
for details, refer to detailed description of each configuration step .
Confidential▲
Start
Register ONU
If there is suitable
ONU profile?
N
Configure ONU
Configure TCONT
profile
Y
Configure GEM Port

TCONT profile?
N
Configure TCONT Configure GEM Port service flow

profile mapping
Y
Configure virtual port

Traffic profile?
N
Configure Traffic profile Configure uplink port VLAN
Save configuration
End
2.3 EPON/10EPON Service Planning
2.3.1 EPON/10G EPON service scenario requirements
At present, EPON line card types supported by the C600 system include 10G EPON,
but not support pure 1G EPON line card. 10G EPON can support EPON channel and 10G
EPON channel (including symmetrical and asymmetric) at the same time, and the
maximum forwarding ability is upstream 10G, and downstream 10G.
Confidential▲
Similar to GPON/XGPON, generally, common scenarios of EPON/10G EPON service

also comprise 4 kinds of services: ITMS management, VOIP, IPTV and broadband service,
Each service configuration corresponds to different CVLANs, if it is HGU, each service a
user-vlan, and corresponds to a CVLAN, and each service a service-port.
2.3.2 EPON/10G EPON basic service scenario configuration flowchart
The basic service configuration flowchart is shown as below. The flowchart is applicable
to all ONU types. For different ONU types, there may differ inside each step, for details,
refer to detailed description of each configuration step .
Confidential▲
Start
Choose a suitable authentication mode

(mac/sn/loid/hybrid)
ONU profile?
N
Configure ONU
profile
Add ONU
Configure bandwidth
Configure PON port VLAN
Configure uplink port VLAN
Configure ONU VLAN
Save configuration
End
Confidential▲
2.4 Planning of Commissioning Data
2.4.1 OLT data planning
OLT management VLAN: 66

OLT management address: 198.16.63.26, mask 255.255.255.252, gateway 198.16.63.25
OLT uplink port xgei-1/18/1 xgei-1/19/1, create aggregation via LACP active mode, and
for load balance at the upstream direction, suggest to use the source MAC load balance,
or OLT uplink ports can also use UAPS protection groups to perform span-card
protection.
2.4.2 GPON/XPON ONU data planning
1) ONU VLAN planning

Plan service VLANs for each place according to your own requirements, for example:
ITMS:
SVLAN: 3901 CVLAN: 4033 user-vlan: 46 ;
IPTV:
SVLAN: 3801 CVLAN: 2613 user-vlan 2613 multicast VLAN: 4070 ;
HSI:
VOIP:
1) ONU rate-limit
TCONT rate-limit is used at upstream, while VPORT rate-limit or service-port rate-
limit is used at downstream. Configure TCONT bandwidth profile, service-port and vport
bandwidth profile (C600 doesn't support gemport rate-limit).
2) Authentication mode
GPON supports multiple authentication modes, configure according to your own
requirements on-site. Generally, LOID authentication is used.
2.4.3 EPON/10GEON ONU data planning
VLAN planing for a variety of services
Confidential▲
Plan service VLANs for each place according to your own requirements, for example:
ONU management:
SVLAN:3800 CVLAN :10 user-vlan:10
IPTV:
SVLAN: 3800 CVLAN: 51 user-vlan 51 multicast VLAN: 4070 ;
HSI:
VOIP:
ONU rate-limit
TCONT rate-limit is used at upstream, while VPORT rate-limit or service-port rate-
limit is used at downstream. Configure TCONT bandwidth profile, service-port and vport
bandwidth profile (C600 doesn't support gemport rate-limit).
Authentication mode
EPON supports multiple authentication modes such as MAC\LOID\PW, configure
according to your own requirements on-site. Generally, LOID authentication is used.
3 Global Data Configuration for C600
Commissioning
3.1 Connect via the Serial Port and Introduce Ports on
the Panel of Switching & Control Card
Use a serial port cable to connect the CONSOLE port and PC of C600’s master main
control card, and set the serial port’s baud rate as 115200, and then you can log in the
OLT immediately after connected. The default enabling password is zxr10. The panel
figure of a C600 switching & control card is shown as below: USB port, CONSOLE port,
ODB port, MGMT out-band Ethernet port, DIAG interface from top to bottom. In addition,
at present, the DIAG interface can only be used for microcode debugging, inner / panel
port serdes debugging, control panel flow mirroring, but can’t be used for uplink port or
CPU mirroring and packet capturing. Therefore, at present, to mirror and capture packets
at the uplink ports, the optical-electrical module can only be used to connect a PC to
capture packets.
Confidential▲
3.2 Create User Name / Password for C6xx
C600V1.0.0 version system has the default telnet user name zte, and password zte,
but starting from C6xxV1.1.0 version, the default user name / password can only be used
once, with the user name as zte, and password as ZxPon1!2@3#. Because the default user
name password will invalid after exited, you need to modify or create the user name /
password once again, otherwise, you will fail to log in again. However, in some places,
factory setting may set the default user name / password as zte, so when logging in for
the first time, try both passwords, or you can create a new user name, password
according to your own requirements. And set RADIUS or Tacacs authentication modes.
3.2.1 Create user name / password of local authentication
ZXAN#con t
ZXAN(config)#system-user
ZXAN(config-system-user)#user-name debug---------Set the user name according to your own
requirements
ZXAN(config-system-user-username)# password admin ----------Set the password according to your
own requirements
ZXAN(config-system-user-username)#bind authentication-template 1
ZXAN(config-system-user-username)#bind authorization-template 1
ZXAN(config-system-user-username)#exit
ZXAN(config-system-user)#authentication-template 1
Confidential▲
ZXAN(config-system-user-authen-temp)#bind aaa-authentication-template 2001

ZXAN(config-system-user-authen-temp)#exit
ZXAN(config-system-user)#authorization-template 1
ZXAN(config-system-user-author-temp)#bind aaa-authorization-template 2001
ZXAN(config-system-user-author-temp)#local-privilege-level 15
ZXAN(config-system-user-author-temp)#exit
ZXAN(config-system-user)#exit
ZXAN(config)#aaa-authentication-template 2001
ZXAN(config-aaa-authen-template)#aaa-authentication-type local
ZXAN(config-aaa-authen-template)#exit
ZXAN(config)#aaa-authorization-template 2001
ZXAN(config-aaa-author-template)#aaa-authorization-type local
ZXAN(config-aaa-author-template)#exit
3.2.2 Create user name / password of RADIUS authentication
For users authenticated via RADIUS, configurations of C600 and C300 differ a lot:
ZXAN#con t
requirements
own requirements
ZXAN(config-system-user)#authentication-template 1 ----------------Bind the authentication profile

ZXAN(config-system-user)#authorization-template 1 -----------------Bind the authorization profile
ZXAN(config-system-user)#user-default ----------------------Set the default user, after this function is set,

you don't need to set the user name / password on the OLT to log in. If you need to set user name /
password on the OLT, this configuration isn't needed
ZXAN(config-system-user-default)#bind authentication-template 1
ZXAN(config-system-user-default)#bind authorization-template 1
Confidential▲
ZXAN(config-system-user-default)#exit
ZXAN(config)#radius authentication-group 1 ------------Under config mode, configure radius

authentication group
ZXAN(config-authgrp-1)#deadtime 1
ZXAN(config-authgrp-1)#max-retries 2
ZXAN(config-authgrp-1)#nas-ip-address y.y.y.y -------------In-band management IP of the OLT
ZXAN(config-authgrp-1)#server 1 x.x.x.x key abc port 1812 -------IP1 of the server
ZXAN(config-authgrp-1)#server 2 x.x.x.x key abc port 1812 -------IP2 of the serve
ZXAN(config-authgrp-1)#timeout 2
ZXAN(config-authgrp-1)#exit
ZXAN(config)#aaa-accounting-template 2001 ---------Under config mode, configure the radius

accounting template
ZXAN(config-aaa-acct-template)#aaa-accounting-type radius
ZXAN(config-aaa-acct-template)#exit
ZXAN(config)#aaa-authentication-template 2001-------Under config mode, configure the radius
authentication template
ZXAN(config-aaa-authen-template)#aaa-authentication-type radius
ZXAN(config-aaa-authen-template)#authentication-radius-group 1
ZXAN(config)#aaa-authorization-template 2001--------Under config mode, configure the radius
authorization template
ZXAN(config-aaa-author-template)#aaa-authorization-type radius
ZXAN(config-aaa-author-template)#authorization-radius-group 1
3.2.3 Configure user name / password of Tacacs authentication
For users authenticated via Tacacs, configure as following:

ZXAN#con t
requirements
own requirements
Confidential▲
ZXAN(config-system-user)#authentication-template 1 ---------------- Bind the authentication profile

ZXAN(config-system-user)#authorization-template 1 ----------------- Bind the authorization profile
ZXAN(config-system-user)#user-default ----------------------Set the default user, after this function is set,

you don't need to set the user name / password on the OLT to log in. If you need to set user name /
password on the OLT, this configuration isn't needed
ZXAN(config-system-user-default)#bind authentication-template 1
ZXAN(config-system-user-default)#bind authorization-template 1
ZXAN(config-system-user-default)#exit
ZXAN(config)#tacacs enable ------------------------------Enable the tacacs authentication

ZXAN(config)#tacacs-server host 1.1.1.1 ----------------Specify the ip address of the tacacs-server
ZXAN(config)#tacplus group-server ztegroup -------------Configure the tacacs group ztegroup
ZXAN(config-sg)#server 10.1.1.1 ---------------------------Configure the address of the group ztegroup’s
server
ZXAN(config-sg)#exit
ZXAN(config)#aaa-authentication-template 2001-------Under config mode, configure the tacacs

authentication template
ZXAN(config-aaa-authen-template)#aaa-authentication-type tacacs
ZXAN(config-aaa-authen-template)#authentication-tacacs-group ztegroup
ZXAN(config)#aaa-authorization-template 2001--------Under config mode, configure the tacacs
authorization template
ZXAN(config-aaa-author-template)#aaa-authorization-type tacacs
ZXAN(config-aaa-author-template)#authorization-tacacs-group ztegroup
3.3 Add Physical Configuration
C6xx equipment doesn’t need to add racks and shelves, which is automatically
identified by the system. At the same time, the PNP function is enabled by default:
Confidential▲
ZXAN(config)#show pnp
Equipment PNP function is enable.
To disable the PNP function:
ZXAN(config)#set-pnp disable -------------------Enabling the PNP function needs to configure it as
enable
ZXAN(config)#show pnp
Equipment PNP function is disable.
At the same time, C600 and C300 are the same, no matter whether to enable the PNP
function or not, switching & control cards are automatically identified to generate, with
no need to manually add. During commissioning, if PNP is disabled, you only need to
manually add uplink cards and service cards.
Manually add cards by using following commands:
ZXAN#config t
ZXAN(config)#add-card rackno 1 shelfno 1 slotno 1 GFBH
ZXAN(config)#add-card rackno 1 shelfno 1 slotno 2 GFXH
ZXAN(config)#add-card rackno 1 shelfno 1 slotno 3 GFGO
ZXAN(config)#add-card rackno 1 shelfno 1 slotno 4 GFGH
ZXAN(config)#add-card rackno 1 shelfno 1 slotno 5 GFXO
ZXAN(config)#add-card rackno 1 shelfno 1 slotno 6 EFTO
ZXAN(config)#add-card rackno 1 shelfno 1 slotno 7 EFTH
ZXAN(config)#add-card rackno 1 shelfno 1 slotno 18 XFTO
ZXAN(config)#add-card rackno 1 shelfno 1 slotno 19 XFTO
3.4 Configure Out-band / In-band Management Address
3.4.1 Configure out-band management address
Show the out-band management address of the NE:

ZXAN(config)#show running-config-interface mgmt_eth
!<if-intf>
interface mgmt_eth
ip address 136.1.1.100 255.255.255.0
$
!</if-intf>
Configure the out-band management address:
ZXAN#con t
ZXAN(config)#interface mgmt_eth
Confidential▲
ZXAN(config-if-mgmt_eth)#no ip address ----------The out-band management IP is 136.1.1.100 by

default, if it needs to be modified, delete it first, and then configure gu
ZXAN(config-if-mgmt_eth)# ip address 192.168.1.100 255.255.255.0
ZXAN(config-if-mgmt_eth)#exit
3.4.2 Configure in-band management address and route
1)Create the in-band management VLAN

ZXAN#con t
ZXAN(config)#vlan 66
2)Configure the IP address in L3 interface of the in-band management VLAN
ZXAN(config)#interface vlan66
ZXAN(config-if-vlan66)# ip address 198.16.63.26 255.255.255.252
ZXAN(config-if-vlan66)# exit
3)Configure the route of the in-band management address
ZXAN(config)#ip route 0.0.0.0 0.0.0.0 198.16.63.25
4) Add the in-band management VLAN to the uplink port or switchport
ZXAN(config)#interface xgei-1/18/1
ZXAN(config-if-xgei-1/18/1)#switchport mode hybrid
ZXAN(config-if-xgei-1/18/1)#switchport vlan 66 tag
ZXAN(config-if-xgei-1/18/1)#exit
After EMS channel is smooth, routing states can be viewed through following
commands:
ZXAN(config)#show ip forwarding route or show ip protocol routing all
IPv4 Routing Table:
Headers: Dest: Destination, Gw: Gateway, Pri: Priority;
Codes: BROADC: Broadcast, USER-I: User-ipaddr, USER-S: User-special,
MULTIC: Multicast, USER-N: User-network, DHCP-D: DHCP-DFT,
ASBR-V: ASBR-VPN, STAT-V: Static-VRF, DHCP-S: DHCP-static,
GW-FWD: PS-BUSI, NAT64: Stateless-NAT64, LDP-A: LDP-area,
GW-UE: PS-USER, P-VRF: Per-VRF-label, TE: RSVP-TE,
BP: BRAS-pool, HAGP: Hybrid-access-gateway-protocol;
Status codes: *valid, >best, R: Relay;
Dest Gw Interface Owner Pri Metric
*> 0.0.0.0/0 198.16.63.25 vlan66 Static 1 0
*> 198.16.63.24/30 198.16.63.26 vlan66 Direct 0 0
*> 198.16.63.26/32 198.16.63.26 vlan66 Address 0 0
Confidential▲
3.5 Create LACP Smartgroup
3.5.1 Add the in-band management VLAN to the uplink port
Add the planned in-band management VLAN, service VLAN into the uplink port:
ZXAN#con t
ZXAN(config-if-xgei-1/18/1)#switchport vlan 100-200 tag
3.5.2 Create smartgroup and add to VLAN
ZXAN(config)#interface smartgroup1
ZXAN(config-if-smartgroup1)#switchport mode hybrid
ZXAN(config-if-smartgroup1)#switchport vlan 66 tag
ZXAN(config-if-smartgroup1)#exit
3.5.3 Create dynamic smartgroup
ZXAN(config)#lacp
ZXAN(config-lacp)#interface smartgroup1
ZXAN(config-lacp-sg-if-smartgroup1)#lacp mode 802.3ad -------Configure smartgroup dynamic
mode
ZXAN(config-lacp-sg-if-smartgroup1)#lacp load-balance src-mac --Configure the load balance
mode
ZXAN(config-lacp-sg-if-smartgroup1)#exit
ZXAN(config-lacp)#interface xgei-1/18/1
ZXAN(config-lacp-member-if-xgei-1/18/1)#smartgroup 1 mode active
ZXAN(config-lacp-member-if-xgei-1/18/1)#exit
Confidential▲
ZXAN(config-lacp)#interface xgei-1/19/1
ZXAN(config-lacp-member-if-xgei-1/19/1)#smartgroup 1 mode active
ZXAN(config-lacp-member-if-xgei-1/19/1)#exit
ZXAN(config-lacp)#exit
ZXAN(config-if-xgei-1/18/1)#no shutdown -------------------------- The uplink port and PON port are
shutdown by default, first, you need to configure no shutdown to be able to use
ZXAN(config-if-xgei-1/19/1)#no shutdown -------------------------- The uplink port and PON port are
shutdown by default, first, you need to configure no shutdown to be able to use.
If LACP of both ends has already been configured, and interconnected successfully,
show LACP status as following:
ZXAN#show lacp 1 counters
Smartgroup:1
Actor LACPDUs Marker LACPDUs Marker
Port Tx Rx Tx Rx Err Err
-------------------------------------------------------------------
xgei-1/18/1 2605 2548 0 0 0 0
xgei-1/19/1 2605 2556 0 0 0 0
ZXAN#show lacp 1 internal
Smartgroup:1
Flags: * - Port is Active member Port
S - Port is requested in Slow LACPDUs
F - Port is requested in Fast LACPDUs
A - Port is in Active mode
P - Port is in Passive mode
Actor Agg LACPDUs Port Oper Port RX Mux
Port[Flags] State Interval Pri Key State Machine Machine
--------------------------------------------------------------------------------
xgei-1/18/1[SA*] ACTIVE 30 32768 0x121 0x3d CURRENT COLL&DIST
xgei-1/19/1[SA*] ACTIVE 30 32768 0x121 0x3d CURRENT COLL&DIST
ZXAN#show lacp 1 neighbors
Smartgroup 1 neighbors
Actor Actor Partner Partner Port Oper Port
Port Port No. System ID Port No. Priority Key State
-------------------------------------------------------------------------------
xgei-1/18/1 4609 0x8000,cc1a.faea.0ee0 8276 32768 0x1f21 0x3d
xgei-1/19/1 4865 0x8000,cc1a.faea.0ee0 8290 32768 0x1f21 0x3d
Confidential▲
3.6 Create UAPS Protection Groups
3.6.1 Configure master / slave protection relationship
ZXAN(config)#uaps-group 1 ------------------Create a UAPS protection group
ZXAN(config-uaps-1)#master-port interface xgei-1/18/1 -------------Set the UAPS master port
ZXAN(config-uaps-1)#slave-port interface xgei-1/19/1 -------------Set the UAPS slave port
ZXAN(config)#show uaps groupid 1
Revertive control : disable
PortLight control : disable
Protect-time : 300s
Is-in-protect-time : no
Next-hop : 0.0.0.0
Link-detect-retry : 5
Link-detect-interval : 3s
Link status : N/A
Switch-type : common port
Failure-time : 430s
Swap-reason : no swap
Master ports status : forwarding
xgei-1/18/1: down
Slave ports status : blocking
xgei-1/19/1: down
ZXAN(config)#uaps-group ? -------- At most 16 UAPS protection groups can be created in

the system
<1-16> Configure uaps-group id
ZXAN(config)#uaps-group
Precautions:
Confidential▲
1) Data configuration of the master active port and slave active port participating in
protection switching must be consistent, the UAPS function itself doesn’t have the
automatic synchronize data function.
2) Service forwarding of the master active port and slave active port participating in
protection switching doesn’t exist load balance relationship, but just simple master /
slave protection relationship.
3.6.2 Configure UAPS protection switching time
ZXAN(config)#uaps-group 1 -------------------Enter the uaps protection group
ZXAN(config-uaps-1)#revertive enable ---------Enable the automatic revertive function
ZXAN(config-uaps-1)#protect-time ? ------------Configure the protection switching time (300s by

default)
<0-900> Time (second, [0-900], default 300s )
Precautions:
1. The switching protection time is the interval from triggering switching back to the
master port after the master active port recovers to normal.
2. To make the switching protection time take effect, the automatic revertive function
needs to be enabled.
3.6.3 Set the triggering condition for UAPS protection switching
ZXAN(config)#uaps-group 1 -------------------Enter the uaps protection group
ZXAN(config-uaps-1)#switch-type max-ports-switch -----------Set the switching type as max-port

mode
Precautions:
1)For UAPS protection groups of single-port or smartgroup, the switching trigger

condition is that switching will be triggered when all ports of the current active port are
down.
2)For multi-port UAPS protection groups, the switching trigger condition can be set as
max-port mode, meaning that as long as faulty ports among current active ports are
more than non-active ports, switching will be triggered.
Confidential▲
3.6.4 Configure UAPS protection for Smartgroup
ZXAN(config)#uaps-group 1 ----------------Enter the uaps protection group.
ZXAN(config-uaps-1)#switch-type trunking-port ---------Set the switching type as trunking. You

must first set it as trunking, otherwise, you will fail to add multiple ports as UAPS active port or
protection port.
Precautions:
Smartgroup port must be manually added into the UAPS group, and you can’t
directly add smartgroup through commands. The switching trigger mode must be set as
trunking.
ZXAN(config-uaps-1)#master-port interface xgei-1/18/6 --------------Add multiple ports to the UAPS

active port
ZXAN(config-uaps-1)#master-port interface xgei-1/19/6
ZXAN(config-uaps-1)#slave-port interface xgei-1/18/7 --------------Add multiple ports to the UAPS

protect port
ZXAN(config-uaps-1)#slave-port interface xgei-1/19/7
ZXAN(config-uaps-1)#exit
After the adding of the UAPS port is completed, configure two smartgroup
protection groups. The configuring order of smartgroup or uaps protection groups
doesn’t matter, it is OK about which one is configured first. For smartgroup
configuring method, please refer to above Section 5.
Show as below after configuration is completed:
ZXAN(config-uaps-1)#show uaps groupid 1
Revertive control : disable
PortLight control : disable
Protect-time : 300s
Is-in-protect-time : no
Next-hop : 0.0.0.0
Link-detect-retry : 5
Link-detect-interval : 3s
Link status : N/A
Confidential▲
Switch-type : trunk port
Failure-time : 136s
Swap-reason : port deleted
Master ports status : forwarding
xgei-1/18/6: down
xgei-1/19/6: down
Slave ports status : blocking
xgei-1/18/7: down
xgei-1/19/7: down
ZXAN(config-lacp)#show lacp internal
Smartgroup:1
--------------------------------------------------------------------------------
xgei-1/18/6[ A ] INACTIVE 30 32768 0x100 0x45 PORT_DISABLED DETACHED
Smartgroup:2
--------------------------------------------------------------------------------
Confidential▲
ZXAN(config-lacp)#
3.7 Add C600 NE on EMS
At present, the EMS version supporting C600 NE management is T125 and later
versions. After the NE is added on EMS, configure the community name and view, which
are strict case-sensitive. In addition, all snmp versions are Disable in the system by
default, corresponding snmp version needs to configured as Enable on the NE. Following
are examples to configure snmp v2c enable and configure the trap server.
ZXAN#config t
Enter configuration commands, one per line. End with CTRL/Z.
ZXAN(config)#snmp-server version v2c enable --------Enable the SNMP V2C
ZXAN(config)#snmp-server community public view Allview rw --------Configure the community name,
view must be AllView, and pay attention to case
ZXAN(config)#snmp-server enable trap ------------------Enable the snmp trap
ZXAN(config)#snmp-server host 198.10.10.10 trap version 2c public --------Configure the trap server
View the configuration effect:
ZXAN(config)#show snmp config
snmp-server community encrypted
d6ddeaa4dab74523b246fe346c94c31ae58b79ad4776396438ea1e9bb01a9ef3 view AllView rw
snmp-server engine-id is 830900020300010289d64401
snmp-server host 198.10.10.10 trap version 2c encrypted
d6ddeaa4dab74523b246fe346c94c31ae58b79ad4776396438ea1e9bb01a9ef3 udp-port 162 snmp bgp
mac ospf stp ppp arp rmon
udld cfm efm lacp mc-elam tcp sctp stalarm cps interface acl fib pim isis rip msdp aps config am um
system ldp pwe3 vpn mpls-oam ptp tunnel-te radius dhcp bfd ippool n
tp ssm sqa ipsec cgn vrrp ftp_tftp ping-trace gm
snmp-server packetsize is 8192
snmp-server view AllView internet included
snmp-server view DefaultView system included
snmp-server security dynamic-trust-user idle-timeout 1800
snmp-server listen-port is 161
snmp-server version v2c enable
snmp-server input-limit 200
Note: If there are no special requirements, do not enable inform at will: ZXAN(config)#snmp-
server enable inform
Confidential▲
Otherwise, it may cause EMS or third-party EMS to receive too many messages, leading to
congestion.
If misoperations appear, please configure as below:
ZXAN(config)#no snmp-server enable inform
3.8 Multicast Global Configuration
3.8.1 Configure the slave switch and configure multicast group
The default master / slave working mode of the C600 system is Proxy. As for whether to use snooping or
proxy, configure according to needs of users.
ZXAN#config t
ZXAN(config)#igmp enable ---------------Generally, it is enable by default
ZXAN(config)#igmp span-vlan enable
ZXAN(config)#igmp mvlan 4070
ZXAN(config-igmp-mvlan-4070)#work-mode proxy
ZXAN(config-igmp-mvlan-4070)#group 235.254.196.1 to 235.254.196.255
ZXAN(config-igmp-mvlan-4070)#prejoin-group 235.254.196.1
ZXAN(config-igmp-mvlan-4070)#prejoin-group 235.254.198.51
3.8.2 Configure multicast source port and receive port
ZXAN(config-igmp-mvlan-4070)#source-port xgei-1/19/1
ZXAN(config-igmp-mvlan-4070)#source-port smartgroup1----------------If uplink is smartgroup, you
need to add smartgroup as the source port
ZXAN(config-igmp-mvlan-4070)#receive-port vport-1/1/1.3:2 -------------Add the receive port according
to needs of the user, which can be configured after the ONU is added.
ZXAN(config-igmp-mvlan-4070)#receive-port vport-1/1/1.1:2
Confidential▲
ZXAN(config-igmp-mvlan-4070)# exit
3.8.3 Configure multicast to retrieve packets based on VLAN
ZXAN(config-sub-3801)#igmp span-vlan ------------VLAN 3801 is the SVLAN for multicast to get the
DHCP IP address. This configuration is very important, otherwise, upstream won’t retrieve packets but
transparently transmit under the circumstances of span-VLAN multicast.
ZXAN(config-sub-3801)#exit
ZXAN(config-sub-4070)#multicast-packet dropUnknown -------------Configure to drop multicast flood
messages
Note: The system adopts span-VLAN multicast by default, multicast VLAN can
automatically retrieve packets, so igmp span-vlan doesn’t need to be configured in
multicast VLAN. However, if upstream direction multicast messages go through non-
multicast VLAN, the VLAN’s igmp span-vlan must be configured, if going through dual-
layer VLAN, igmp span-vlan is configured in SVLAN.
3.9 Configure ACL
3.9.1 Create ACL and rule
Create ACL according to your own requirements.

ACL creation of C600 doesn’t need to specify whether it is standard ACL, hybrid or link,
but just needs to type number.
ZXAN(config)#acl ?
number Configure ACL
ZXAN(config)#acl nu
ZXAN(config)#acl number ?
<1-699> Configure ACL number
ZXAN(config)#acl number 1 ?
<cr>
For example:
acl number 1
rule 1 permit any 61.166.57.0 0.0.0.255 any any
Confidential▲

rule 13 deny any any any any
3.9.2 Bind ACL
1)Bind ACL to telnet

ZXAN(config)#line telnet access-class ipv4 1
2)Bind ACL to snmp
ZXAN(config)#snmp-server access-list ipv4 1
3)Bind ACL to vport
ZXAN(config)#interface vport-1/6/1.1:1
C600(config-if-vport-1/6/1.1:1)#ip access-group 1 in
4)Bind ACL to smartgroup
C600(config-if-smartgroup1)# ipv4-access-group ingress 1
5)Bind ACL to uplink port
C600(config-if-xgei-1/14/6)#ipv4-access-group ingress 1
If the port has been added to a smartgroup, you need to first remove the port from the smartgroup, to
be able to add acl into the physical port, otherwise, it needs to be added to smartgroup.
3.9.3 View all ACL entries bound
ZXAN(config-if-vport-1/2/1.1:1)#show access-list bound

Interface Direction Acl number
vport-1/2/1.1:1 in 101
Confidential▲
3.10 Other Global Configurations
3.10.1 Modify the system timezone and time
The default system time of C600 is Greenwich time, to guarantee that the system time
and EMS time are consistent or close, modify according to local timezone:
ZXAN#show clock
08:50:05 UTC Thu Jan 18 2018
ZXAN#config t
ZXAN(config)#clock timezone Beijing 8
ZXAN(config)#show clock
16:50:44 Beijing Thu Jan 18 2018
ZXAN(config)#exit
ZXAN#clock set 8:51:30 ?
MM-DD-YYYY Current date from 1-1-2001 to 12-31-2037
ZXAN#clock set 8:51:30 1-18-2018 ?
<cr>
ZXAN#clock set 8:51:30 1-18-2018
ZXAN#show clock
08:51:31 Beijing Thu Jan 18 2018
3.10.2 Configure the NTP connection server
ZXAN#Config t
ZXAN(config)#ntp enable
ZXAN(config)#ntp poll-interval 6
ZXAN(config)#ntp server 10.10.10.10 priority 1 ---------------NTP server 1
ZXAN(config)#ntp server 10.10.10.20 priority 5---------------NTP server 2
Note: NTP clock synchronization requires timezone of the NE and that of the server to
be consistent, and the interval is within 1000s, otherwise, clock fails to be synchronized.
3.10.3 Set Telnet and serial port timeout time
ZXAN(config)#line telnet idle-timeout ?

<0-1000> Idle timeout in minutes
Confidential▲
ZXAN(config)#line console idle-timeout ?

<0-1000> Idle timeout in minutes
ZXAN(config)#line console idle-timeout 15 ----------Unit: minute

ZXAN(config)#line telnet idle-timeout 10 ----------Unit: minute
3.10.4 Method to Modify Three-Packet Limit
Three packets refer to broadcast packet, unknown unicast packet, unknown multicast
packet respectively:
ZXAN(config)#show eth-switch stormcontrol
pkttype limitnum(unit:pps)
broadcast 100
unknowncast 100
multicast unlimited
Modify three-packet limit:

Generally, suggest to set broadcast, unknown unicast limit as 100, unknown multicast as
not limit, and configure to drop unknown multicast in vlan.
ZXAN(config)#eth-switch ?
broadcast-limit Configure broadcast-limit operation
l2cp Configure l2cp record
mac-protect Configure protected mac-address
max-frame-length Configure max-frame-length
multicast-limit Configure multicast-limit operation
unknowncast-limit Configure unknowncast-limit operation
ZXAN(config)#eth-switch broadcast-limit ?
<0-1000000> Broadcast limit (unit is pps, default 100pps)
ZXAN(config)#eth-switch mul
ZXAN(config)#eth-switch multicast-limit ?
<0-1000000> Multicast limit(unit is pps, default no limit)
ZXAN(config)#eth-switch unk
ZXAN(config)#eth-switch unknowncast-limit ?
<0-1000000> Unknowncast limit(unit is pps, default 100pps)
3.10.5 Set port delay down
The delay down function of C600 uplink port supports to configure based on ports, when
configuring, you need to enter the port mode to configure, and the system’s default
value is 120s:
ZXAN(config-if-xgei-1/18/1)#holdtime 100
Confidential▲
Show the configuration effect:

ZXAN#show holdtime xgei-1/18/1
ShelfNo SlotNo Subslot Port Holdtime(s)
1 18 0 1 100
4 GPON/XGPON ONU Commissioning
4.1 Create ONU Type Profile
4.1.1 Create general ONU profile
Choose the ONU type profile that you need to configure, HGU doesn’t need to configure eth
interface, while SFU need to configure it. Its configuring method is the same as C300.
ZXAN#con t
ZXAN(config)#pon
ZXAN(config-pon)#onu-type ZTE-1866 epon description 4GE,2POTS,4WLAN
ZXAN(config-pon)#onu-type ZTE-F220 gpon
ZXAN(config-pon)#onu-type GPON-E8C gpon max-tcont 7 max-gemport 8 max-flow-perswitch 1
ZXAN(config-pon)#onu-type ZTEG-612 gpon description F612-2FE
ZXAN(config-pon)#onu-type 4FE2POS4WLAN gpon
ZXAN(config-pon)#onu-type 8FE8POS4WLAN gpon
ZXAN(config-pon)#onu-type ZTEG-F2866 gpon
ZXAN(config-pon)#onu-type-if ZTE-F220 eth_0/1
ZXAN(config-pon)#onu-type-if ZTEG-F2866 eth_0/1
ZXAN(config-pon)#onu-type ZTEG-F600 gpon description 4FE
ZXAN(config-pon)#onu-type ZTEG-F620 gpon description 4FE,2POTS max-tcont 8 max-gemport 32 max-flow-perswitch 8
ZXAN(config-pon)#onu-type ZTEG-F660 gpon description 4FE,2POTS1WIFI
ZXAN(config-pon)# onu-type-if ZTEG-F600 eth_0/2
ZXAN(config-pon)# onu-type-if ZTEG-F600 eth_0/3
Confidential▲

ZXAN(config-pon)#onu-type-if ZTEG-F620 pots_0/1
ZXAN(config-pon)#onu-type-if ZTEG-F660 wifi_0/1
ZXAN(config-pon)#uncfg-onu-display-info sn loid ------------Configure to show SN and LOID of un-
authenticated ONUs, to show passwords, just add pw: ZXAN(config-pon)#uncfg-onu-display-info sn loid

pw
4.1.2 Special Configurations of ONU Profile
Except general ONU configurations above-mentioned, according to different

application scenarios or different ONU requirements, it is possible to add some special
configurations when configuring ONU type profile. These configurations are generally
unable to be modified by default, but need to be configured for some special scenarios.
Suggest to contact with our R & D personnel to evaluate before configuration.
1) Speed mode of ONU
Normally, the speed mode of the ONU is automatically matched. But for combo pon,
because when LOID authentication happens on the ITMS number distribution process,
except ONU on-line, you still need to send LOID to the ITMS platform to authenticate, at
this time, under the combo pon environment, the OLT will kick the ONU when matching
ONU speed, causing number distribution process needs to send LOID once again,
affecting the number distribution feeling. Suggest to specify speed as below when
creating the ONU type profile:
ZXAN(config-pon)#onu-type TEST1220 gpon speed-mode ?
auto Auto
gpon GPON ONU
xg-pon XG-PON ONU
xgs-pon XGS-PON ONU
ZXAN(config-pon)#onu-type TEST1220 gpon speed-mode
2) Multicast address dispatching
Confidential▲
Generally, ONUs will configure multicast address by default, to guarantee normal

multicast forwarding. But some other ONU vendors have no multicast forwarding address
by default, which is dispatched by the OLT based on specifications, at the time, if the
multicast group address can’t be determined, forward all multicast by default, following
configurations need to be performed:
ZXAN(config-pon)#onu-type TEST1220 gpon default-multicast-range ?
all-inclusive All inclusive
none None
ZXAN(config-pon)#onu-type TEST1220 gpon default-multicast-range all-inclusive -------Forward all
multicast addresses
3)Control OMCI dispatching mode

To guarantee the success rate of ONU upstream speed and work order dispatching,
most OMCI dispatching of current GPON are asynchronous, but sometimes, some
vendors need synchronous mode, so it needs to be evaluated and modified.
ZXAN(config-pon)#onu-type TEST1220 gpon omci-send-mode ?
async Asynchronous
sync Synchronous
ZXAN(config-pon)#onu-type TEST1220 gpon omci-send-mode
4) Other Configuration Specifications

For configurations of the ONU’s ability set, these settings need to combine the
ONU’s ability set to configure, in order to avoid the situation that the ability set of the
ONU profile exceeds the actual ability of the ONU, causing ONU problems, suggest to try
to set the ONU’s ability set smaller.
ZXAN(config-pon)#onu-type TEST1220 gpon ?
default-multicast-range Default multicast address range
description Description
ex-omci Extended OMCI configure mode
location PON location
max-flow-perswitch Max flow per switch --------Configure maximum flows of each bridge
port
max-gemport Max GEM port ---------Configure maximum gemports of each
ONU
max-iphost Max IP host ----------Configure maximum ipv4 hosts of each ONU
max-ipv6-host Max IPv6 host ---------Configure maximum ipv6 hosts of each ONU
max-switch-perslot Max switch per slot ----Configure maximum bridge ports of each
ONU slot
max-tcont Max T-CONT ----------Configure maximum tconts of each ONU
Confidential▲
max-veip Max VEIP ----------Configure maximum VEIPs of each ONU

mgc-cfg-mode MGC configure mode -----Configure the mgc configuration mode
of ONU VoiP registration
omci-send-mode OMCI send mode
service-ability Service ability
service-mgmt-via-non-omci Service management via non OMCI
speed-mode ONU speed mode
<cr>
4.2 Create GPON TCONT Bandwidth Profile
Choose the GPON TCONT bandwidth profile that you need to configure, and the
configuring method is the same as C300.
ZXAN#con t
ZXAN(config)#gpon
profile tcont T1-1G type 1 fixed 1000000
profile tcont GPON-BW type 3 assured 10240 maximum 1024000
profile tcont 10M type 2 assured 10240
profile tcont 10GPON-BW type 3 assured 24567 maximum 1024000
profile tcont 20M-GPON type 3 assured 10240 maximum 20480
profile tcont T1-1G type 1 fixed 1000000
profile tcont GPON-BW type 3 assured 10240 maximum 1024000
profile tcont 10GPON-BW type 3 assured 24567 maximum 1024000
profile tcont 20M-GPON type 3 assured 10240 maximum 20480
profile tcont FTTHVOIPUP1M type 4 maximum 1024
profile tcont FTTBVOIPUP20M type 4 maximum 20480
profile tcont FTTH_UN type 4 maximum 25600
profile tcont FTTH_HG_TF type 4 maximum 102400
profile tcont FTTH_HGU_10M type 2 assured 15360
Use the following commands to view:

C600#show gpon profile tcont
Profile name :default
Type FBW(kbps) ABW(kbps) MBW(kbps) PRIORITY WEIGHT
1 10000 0 0 N/A N/A
Confidential▲
Profile name :LC_ZTE_10M

1 12400 0 0 N/A N/A
Profile name :LC_ZTE_100M

1 102400 0 0 N/A N/A
4.3 Create vport or service-port Rate-limit Bandwidth
Profile
Choose downstream bandwidth profile that you need to create, and under config
mode:
ZXAN#con t
ZXAN(config)#
traffic-profile FTTHVOIPDOWN1M cir 1024 cbs 512 pir 10240 pbs 1023
traffic-profile FTTBVOIPDOWN20M cir 20480 cbs 512 pir 22480 pbs 1023
traffic-profile FTTH_UN cir 5120 cbs 512 pir 1651200 pbs 1023
traffic-profile FTTH_HG_TF cir 665600 cbs 512 pir 1331200 pbs 1023
traffic-profile FTTH_HGU_10M cir 15360 cbs 512 pir 102400 pbs 1023
The following command can be used to view:
C600#show qos traffic-profile
No.1 profile :TEST22
No.2 profile :LC_ZTE_100M
4.4 Configure VOIP-related Profiles
At present, VOIP configurations on C6xx aiming at IP, VLAN configuration need to use
profiles, but do not support non-profile configurations
4.4.1 Create IP Profile
The IP address of onu ip-host can be configured through binding the IP profile.
Confidential▲
Create IP profile:
ZXAN(config-gpon)# --------------Enter the gpon configuration mode
ZXAN(config-gpon)#onu profile ip voip-ip ipv4 gateway 10.23.45.111---Create an IP profile, with

the profile name as test, gateway address as 10.23.45.111
4.4.2 Create VLAN Profile
For VOIP service, you need to configure VLAN-related properties of onu ip-host
through binding VLAN profile.
The configuration command to create VLAN profile:
ZXAN(config-gpon)# --------------------Enter the gpon configuration mode
ZXAN(config-gpon)#onu profile vlan voip-vlan tag-mode tag cvlan 4001 pri 6----Create a vlan
profile, with cvlan as 100, priority as 6
4.4.3 Configure VOIP Protocol Profile
ZXAN(config)#gpon
ZXAN(config-gpon)#onu profile sip test-sip ? ------Create a sip protocol profile, and fill in parameters
according to needs
accesscode VoIP feature access codes profile
appsrv VoIP application service profile
dial-plan Dial plan name
dns1 DNS1
heart-beat Heart beat
media Media
outbound Outbound proxy
port UDP port
proxy Proxy server
reg-exp-time Registration expiration time
registrar Registrar
release-time Release timer
Confidential▲
rereg-time Re-registration time
roh-time ROH timer
ss SS vendor
user-domain The host or domain part of the SIP address
validate Validation scheme
<cr>
ZXAN(config-gpon)#onu profile mgc test-h248 -----------Create MGC profile of H248 or MGCP, and fill
in parameters according to needs
digit-map Digit map
heart-beat Heart beat
heart-beat-interval Heart beat interval
max-retry-attempts Maximum retry attempts
max-retry-time Maximum retry time
media Media
min-avalanche-timer Minimum avalanche timer
min-rereg-timer Minimum rereg timer
msg-format Message format
num-match-shortest Number match shortest
passive-heart-beat Passive heart beat flag
port Port
regmsg-retran-timer Regmsg retran timer
rtp-link-detect RTP link detect
rtp-tid RTP TID
server1 The primary MGC
server2 The secondary or backup MGC
service-change-delay Service change delay
ss SS vendor
user-tid User TID
version Version
<cr>
Confidential▲
4.5 Add Service VLAN to OLT Uplink Port
4.5.1 Single-port Uplinking States
ZXAN#con t
ZXAN(config-if-xgei-1/19/1)#switchport vlan 1000-1999, 3751,3801,4070 tag
4.5.2 Smartgroup Uplinking States
ZXAN#con t
ZXAN(config-if-smartgroup1)#switchport vlan 1000-1999, 3751,3801,4070 tag
ZXAN(config-if-smartgroup1)#exit
4.6 Configure ONU Authentication and Services
4.6.1 Enable the PON port
ZXAN#config t
ZXAN(config)#interface gpon_olt-1/1/1
ZXAN(config-if-gpon_olt-1/1/1)#no shutdown
4.6.2 Configure authenticated ONUs
C600 can query un-authenticated ONUs through show pon onu uncfg, after SN or LOID
is queried, perform registration configuration, or pre-configuration.
ZXAN(config-if-gpon_olt-1/1/1)#onu 1 type 4FE2POS4WLAN loid GPONTEST3
ZXAN(config-if-gpon_olt-1/1/1)#onu 2 type ZTEG-F2866 loid LG0000000010
ZXAN(config-if-gpon_olt-1/1/1)#onu 3 type 4FE2POS4WLAN loid XGPONTEST1
ZXAN(config-if-gpon_olt-1/1/1)#onu 4 type 4FE2POS4WLAN loid test1
ZXAN(config-if-gpon_olt-1/1/1)#onu 5 type 4FE2POS4WLAN loid LG2041178903
ZXAN(config-if-gpon_olt-1/1/1)#onu 6 type 4FE2POS4WLAN loid test2
Confidential▲
4.6.3 Configure tcont and gemport service flows
Tcont and gemport service models are decided according to on-site requirements, it can
be single-tcont and single-gemport, and can also be multi-tcont, multi-gemport. C600
doesn't support gemport rate-limit, but vport or service-port rate-limit can be used. Here,
only consider tcont:gemport as 1:1.
Single-tcont single-gemport:
ZXAN(config)#interface gpon_onu-1/1/1:1
ZXAN(config-if-gpon_onu-1/1/1:1)#tcont 1 profile 10GPON-BW
ZXAN(config-if-gpon_onu-1/1/1:1)#gemport 1 tcont 1
Multi-tcont multi-gemport:
ZXAN(config-if-gpon_onu-1/1/1:6)#tcont 1 name Tl1DefaultCreate profile 10GPON-BW
ZXAN(config-if-gpon_onu-1/1/1:6)#sn-bind disable
ZXAN(config-if-gpon_onu-1/1/1:6)#gemport 1 name Tl1OpVlan46 tcont 1
ZXAN(config-if-gpon_onu-1/1/1:6)#gemport 2 name IPTV tcont 1
4.6.4 HGU configures service data under remote management
C600 ONU remote management only supports simplified service configuration mode,
service flow mapping adopts SERVICE commands, while user port uses vlan port or
multicast vlan commands, to complete configuration of unicast or multicast service.
Single-tcont, single-gemport:
pon-onu-mng gpon_onu-1/1/1:1
vlan port veip_1 mode trunk
vlan port veip_1 vlan 41,43,45-46
service Tl1OpVlan46 gemport 1 vlan 46
or directly transmit transparently

ZXAN(config-gpon-onu-mng)#service 1 gemport 1
ZXAN(config-gpon-onu-mng)#vlan port veip_1 mode transparent
Multi-tcont, multi-gemport:
ZXAN(config)#pon-onu-mng gpon_onu-1/1/1:6
ZXAN(config-gpon-onu-mng)#mvlan 4070
Confidential▲
ZXAN(config-gpon-onu-mng)#service Tl1OpVlan46 gemport 1 cos 0,1,2,3,4,5,6,7 vlan 46

ZXAN(config-gpon-onu-mng)#service IPTV gemport 2 cos 0,1,2,3,4,5,6,7 vlan 2613
ZXAN(config-gpon-onu-mng)#vlan port veip_1 mode trunk
ZXAN(config-gpon-onu-mng)# vlan port veip_1 vlan 46,684,2613,4001
or configure it as transparent:
ZXAN(config-gpon-onu-mng)#vlan port veip_1 mode transparent
Suggest to use multicast simplified configuration and other simplified commands

together:
ZXAN(gpon-onu-mng)# mvlan 4070 --------------Create multicast VLAN4070
ZXAN(gpon-onu-mng)# mvlan tag eth_0/1 strip----Configure the local No. 1 UNI port of the ONU as
multicast TAG strip
If SFUs are used, eth port configuration or VOIP-related configurations need to be added
under pon-onu-mng.
4.6.5 SFU configures service data under remote management
1) Configure related service mapping

Service mapping-related configuration under SFU and that under HGU have no
difference, configure service according to the quantity of gemports
ZXAN(gpon-onu-mng 1/2/1:1)#service inband gemport 4 -----Here, configure to transparently
transmit all VLAN and COS values, and can also specify the specific cos and vlan numbers.
Configure specifically according to on-site requirements
ZXAN(gpon-onu-mng 1/2/1:1)#service voip gemport 1
ZXAN(gpon-onu-mng 1/2/1:1)#service iptv gemport 2
ZXAN(gpon-onu-mng 1/2/1:1)#service hsi gemport 3
2) Configure broadband service UNI interface
For UNI ports of SFU, if it is broadband service, you just need to configure VLAN, if a
PC or router is connected under the ONU, configure the tag mode. If a switch with VLAN
is connected under it, configure the trunk mode.
When broadband service processes above service mapping configuration, you need
to add following new configurations:
Configure bridge mode:
Tag mode scenario:
Confidential▲
ZXAN(config-gpon-onu-mng)#vlan port eth_0/1 mode tag vlan 100------Configure the tag mode
Trunk mode scenario:
ZXAN(gpon-onu-mng)#vlan port eth_0/1 mode trunk----------Configure the trunk mode
ZXAN(gpon-onu-mng)#vlan port eth_0/1 vlan 101,102,103------ Configure vlan transparent under
the trunk mode
3) Configure VOIP service
After the ip profile and vlan profile are created, it can be bound with ONU IP-HOST,
to complete corresponding configurations. And profile configuration mode is suggested
to use with simplified configuration together.
ZXAN(config)#pon-onu-mng gpon-onu_1/2/1:1
IP address can be static or DHCP mode, at present, support three modes: DHCP,
PPPOE and static:
ZXAN(gpon-onu-mng 1/2/1:1)#voip-ip ipv4 mode static ip-profile voip-ip ip-address 10.23.45.1

mask 255.255.255.0 vlan-profile voip-vlan host 1 ------Static IP address mode
ZXAN(gpon-onu-mng 1/2/1:1)# voip-ipipv4 mode dhcp vlan-profile voip-vlan host 1 --------------

-Get IP mode via DHCP
ZXAN(config-gpon-onu-mng)#voip-ip ipv4 mode pppoe username voiptest password aaaa

service-name abc vlan-profile voip-vlan host 1 ----------Mode to get IP via PPPOE
ZXAN(gpon-onu-mng 1/2/1:1)#service 1 gemport 1 vlan 4001 -----Guarantee that service has

already been created
After ONU IP-HOST-related configurations are completed, you still need to

complete VOIP protocol-related configurations, and then complete the VOIP service
configuration. At present, VOIP protocol has three types: SIP/H.248/MGCP. There is no
ONU version that can support three kinds of protocols at the same time, so when
configuring, you need to first confirm the VOIP protocol type supported by ONU
version.
Configuration example:
ZXAN(gpon-onu-mng 1/2/1:1)#voip protocol ? ---Configure the VOIP protocol supported by the ONU
(parameters can be configured according to supporting states of the ONU), after you have chosen the
protocol made, the POTS port needs to be bound to the corresponding protocol profile
h248 H.248 protocol
mgcp MGCP protocol
Confidential▲
non-omci Selected by non-OMCI management interface
none None
sip SIP protocol
ZXAN(gpon-onu-mng)# sip-service pots_0/1 profile test-sip userid 68897417 username

68897417@zte.com.cn password 888888 ------Bind the sip protocol profile to POTS port
ZXAN(gpon-onu-mng 1/2/1:1)#mgc-service pots_0/1 profile test-h248 ----When H248/MGCP

protocol is used, the mgc protocol profile needs to be bound to POTS port
Configure multicast service

Except above service mapping configurations, you still need to add following
multicast configuration:
Multicast service configuration is basically consistent with HGU, and suggest to use
multicast simplified configuration and other simplified commands together:
ZXAN(gpon-onu-mng)# mvlan 4070 --------------Create multicast VLAN4070
ZXAN(gpon-onu-mng)# mvlan tag eth_0/1 strip----Configure the local No. 1 UNI port of the ONU as
multicast TAG strip
4.6.6 Configure service-port
The service-port configuration of C600 is different from C300, it is configured under

the vport interface. Here, only consider tcont:gemport:vport as 1:1:1. In addition, to save
resources, suggest each ONU to use only one VPORT.
Single-tcont single-gemport correspond to single vport:
interface vport-1/1/1.1:1
service-port 1 user-vlan 46 vlan 4000
service-port 2 user-vlan 45 vlan 3499 svlan 3400
Multi-tcont multi-gemport correspond to single vport:
ZXAN(config-if-vport-1/1/1.6:1)# service-port 1 user-vlan 46 vlan 4033 svlan 3901
ZXAN(config-if-vport-1/1/1.6:1)#service-port 1 description Tl1OpVlan46
ZXAN(config-if-vport-1/1/1.6:1)#service-port 2 user-vlan 2613 vlan 2613 svlan 3801
ZXAN(config-if-vport-1/1/1.6:1)#service-port 2 description IPTV
ZXAN(config-if-vport-1/1/1.6:1)#igmp max-groups 8
Confidential▲

ZXAN(config-if-vport-1/1/1.6:1)#service-port 5 user-vlan 4070 vlan 4070
ZXAN(config-if-vport-1/1/1.6:1)#exit
4.6.7 Configure service-port or vport rate-limit
The rate profile must be created in advance, like previous chapter of creating service-
port or vport rate-limit bandwidth profile.
Limit rate for service-port:
ZXAN(config-if-vport-1/1/1.1:1)#service-port 1 user-vlan 41 vlan 1001 svlan 1999 egress
FTTH_HGU_200M -----------Limit rate for each service-port.
Limit rate for vport:
ZXAN(config-if-vport-1/1/1.1:1)#qos traffic-policy FTTH_HGU_200M direction egress---Limit rate for
the whole vport.
4.6.8 VPORT and GEMPORT Mapping Configuration
Configuring vport-mode or not under the PON port doesn’t matter, but under the
interface gpon-onu, be sure to modify vport mode before you create a gemport,
otherwise, after the gemport is created, it can be configured for the first time, later, it
can’t be modified.
ZXAN(config-if-gpon_olt-1/2/4)#onu 2 typeZTE-F601 sn ZTEG12345678
ZXAN(config-if-gpon_olt-1/2/4)#exit
ZXAN(config-if-gpon_onu-1/2/4:2)#vport-mode manual
ZXAN(config-if-gpon_onu-1/2/4:2)#tcont 1 profile UP-10M
ZXAN(config-if-gpon_onu-1/2/4:2)#tcont 2 profile UP-10M
ZXAN(config-if-gpon_onu-1/2/4:2)#vport-map 1 1 vlan 100
ZXAN(config-if-gpon_onu-1/2/4:2)#vport-map 1 2 vlan 200
ZXAN(config-if-gpon_onu-1/2/4:2)#exit
Confidential▲
Show the configuration effect:
ZXAN(config)#show running-config-interface gpon_onu-1/2/4:2
!<if-intf>
interface gpon_onu-1/2/4:2
$
!</if-intf>
!<xpon>
vport-mode manual
tcont 1 profile UP-10M
tcont 2 profile UP-10M
gemport 1 tcont 1
gemport 2 tcont 2
vport 1 map-type vlan
vport-map 1 1 vlan 100
vport-map 1 2 vlan 200
$
$
!</xpon>
ZXAN(config)#show running-config-interface vport-1/2/4.2:1
!<if-intf>
$
!</if-intf>
!<MSAN>
$
!</MSAN>
Confidential▲
5 EPON/10G EPON ONU Commissioning
5.1 Configure EPON Authentication Mode
Different from GPON, EPON needs to first set authentication mode. At present, C600
cancels onu-authentication-mode command in EPON under the global mode, but change
related configuration into commands under the PON port mode, auth-ctrl loid
enable/disable and auth-ctrl sn enable/disable.
1)When both loid and sn are disabled, correspond to MAC authentication mode; if
just loid enabled, correspond to hybrid mode of MAC+LOID; after both loid and sn are
enabled, correspond to hybrid authentication mode.
2)There is no separate loid authentication mode, sn authentication mode can only be
enabled under the circumstances that loid is enabled, that is, there is no separate sn
authentication mode, and do not support to use sn mode to add onu.
3)Under the circumstances that loid and sn are enabled, it is equivalent to the
function of auth-sn-as-loid.
4)Silence is enabled by default, and no switches can be set, that is to say, do not
support to disable silence.
Configuration example:
ZXAN(config-if-epon_olt-1/2/1)#auth-ctrl ?
loid LOID authentication mode
zte-sn SN authentication mode
ZXAN(config-if-epon_olt-1/2/1)#auth-ctrl loid ?
disable Disable
enable Enable
ZXAN(config-if-epon_olt-1/2/1)#auth-ctrl loid enable ?
zte-sn SN authentication mode
<cr>
ZXAN(config-if-epon_olt-1/2/1)#auth-ctrl loid enable zte-sn ?
disable Disable
enable Enable
Confidential▲
ZXAN(config-if-epon_olt-1/2/1)#auth-ctrl loid enable zte-sn
5.2 Create ONU Type Profile
There are already a part of default ONU type profiles on C600, line cards can create
once again according to your own needs.
ZXAN(config)#pon
ZXAN(config-pon)#onu-type ZTE-F420 epon description 4Fe,2Pots ------Configure ONU type profile,

with type as epon, name as ZTE-F420, comprise 4 FE ports, 4 POTS ports
ZXAN(config-pon)#onu-type-if ZTE-F420 eth_0/1-4 ----------Configure No. 1-4 FE ports, eth port

slot must be 0, to be able to configure through OLT remote extended OAM
ZXAN(config-pon)#onu-type-if ZTE-F420 pots_0/1-2 -------Configure No. 1-2 POTS ports in Slot 0; the
slot of F420’s POTS port must also be configured as 0, to be able to configure through OLT remote
extended OAM;
ZXAN(config-pon)#show onu-type-if ZTE-F420 --------The port type and quantity of configured ONU
type profile can be viewed
The system’s default ONU type profiles are listed as following, and you can add other
ONU types according to your own requirements:
ONU type name: ZTE-D400
ONU type name: ZTE-F400
Confidential▲
ONU type name: ZTE-F420M
Precautions
1. ONU types that the system creates by default can’t be deleted and modified, and
user interfaces can’t be added / deleted for them.
5.3 Create Bandwidth Rate-limit Profile
5.3.1 EPON/10G EPON Rate-limit
EPON bandwidth management: Generally, downstream is used for rate-limit, while

upstream is used for DBA scheduling. C600 doesn’t support downstream SLA rate-limit
of ONU, by default, the upstream guaranteed bandwidth is 10M, and the maximum
bandwidth is 100M. If the default bandwidth fails to meet the requirement, you can solve
it through binding bandwidth profile or directly configuring and modifying bandwidth
parameters, while at the downstream direction, like EPON and GPON in C600 that don’t
support GEMPORT rate-limit, EPON also doesn't support downstream SLA rate-limit, only
support VPORT or service-port rate-limit. For bandwidth configuration, try to require the
customer to provide specific bandwidth rate-limit requirements.
Confidential▲
5.3.2 Configure upstream SLA rate-limit profile
SLA rate-limit profile name is generally set according to requirements of customers.

Generally, customers increase gradually from 10M, 20M, 30M, 40M up to 100M, 150M,
200M. Configure SLA upstream bandwidth rate-limit profile following:
ZXAN(config)#epon ----------Enter the EPON configuration interface
ZXAN(config-epon)#onu-sla-profile 500M upstream assured 15000 maximum 51200 ------Create the
SLA profile, the name is 500M, set upstream bandwidth. But under some scenarios, to guarantee
customer user perception, generally, it will be 10%-20% more than actually configured bandwidth.
ZXAN(config)#interface epon_onu-1/14/16:1 ----------Enter the epon onu interface configuration
interface
ZXAN(config-if-epon_onu-1/14/16:1)#sla-profile 500M --------Bind the bandwidth profile
Precautions
The ONU bandwidth profile in the binding status can not be deleted.
5.3.3 Configure downstream VPORT or service-port ate-limit profile
Downstream VPORT or service-port rate-limit profile of EPON services are the same
as downstream rate-limit profile of GPON services, which can also be called together.
Choose the downstream bandwidth profile that you need to create, under config
mode:
ZXAN#con t
ZXAN(config)#
traffic-profile FTTHVOIPDOWN1M cir 1024 cbs 512 pir 10240 pbs 1023
traffic-profile FTTBVOIPDOWN20M cir 20480 cbs 512 pir 22480 pbs 1023
traffic-profile FTTH_UN cir 5120 cbs 512 pir 1651200 pbs 1023
traffic-profile FTTH_HG_TF cir 665600 cbs 512 pir 1331200 pbs 1023
The following command can be used to view:
C600#show qos traffic-profile
No.1 profile: FTTHVOIPDOWN1M
No.2 profile FTTBVOIPDOWN20M
No.3 profile FTTH_HGU_20M
Confidential▲
5.4 OLT Uplink Port Adds Service VLAN
EPON uplink VLAN configuration is as the same as GPON, just add the corresponding
VLAN to the uplink port or switchport. For specific configuration, please refer to Section 4
in Chapter 4.
5.5 Choose 10G EPON Working Mode
ZXAN(config)#interface epon_olt-1/2/1
ZXAN(config-if-epon_olt-1/4/1)#speed ? -----------Choose the working mode needed, generally,
symmetrical and asymmetric needs to be modified, if 1G ONU is connected, it doesn’t need to be
modified.
10G-asymmetric 10G Asymmetric
10G-symmetrial 10G Symmetrial
1G 1G
5.6 Configure ONU Authentication and Service Data
5.6.1 Configure ONU authentication
ZXAN(config)#show pon onu uncfg epon-olt_1/2/1 --------- Query un-authenticated ONUs
ZXAN(config)#interface epon-olt_1/2/1 ------------Enter a certain epon PON port’s configuration

interface
ZXAN(config-if)#onu 1 type ZTE-D420 mac 00d0.d09a.46b6----Configure MAC address registration

ONU
ZXAN(config-if)#show onu all-status epon-olt_1/2/1----View ONU registration status
Precautions
1) A single EPON port supports to register at most 64 ONUs, while a single 10G EPON port
supports to register at most 128 ONUs.
2) During actual applications of EPON, the quantity of ONUs under each PON needs to
confirmed through combining specific service and requirements of the customer. When
Confidential▲
planning, try to ensure that types of ONUs connected under one PON port are the same, to
facilitate unified distribution of bandwidth, VLAN and so on.
5.6.2 Configure services under ONU interface
Under the EPON ONU interface, because it doesn’t need to configure service flows and
other configurations like GPON, it only needs to configure description information and
upstream bandwidth rate-limit and so on.
ZXAN(config)#interface epon_onu-1/2/1:1
ZXAN(config-if-epon_onu-1/2/1:1)#description test-12345678
ZXAN(config-if-epon_onu-1/2/1:1)#sla-profile 500M vport 1
5.6.3 Configure HGU remote management
If there are no special requirements, because all are transparently transmitted under
the EPON HGU remote management, there is no need to perform any configuration.
5.6.4 Configure SFU remote management
Enable the remote management automatic dispatching

ZXAN(config)#pon-onu-mng epon_onu-1/2/1:1
ZXAN(config-epon-onu-mng)#auto-config enable ---UNI port data dispatching is Enable by default
ZXAN(config-epon-onu-mng)#auto-config voip enable---VOIP data dispatching is Disable by
default
Configure broadband UNI port service
UNI port service configuration of EPON SFU is very simple, under the circumstances
that automatic dispatching is guaranteed as enable, just configure VLAN and priority of
the UNI port.
ZXAN(config-epon-onu-mng)#vlan port eth_0/1 mode tag vlan 100 priority 0 --------Configure it as
tag mode when a PC or router is connected under it
ZXAN(config-epon-onu-mng)#vlan port eth_0/1 mode trunk vlan-list 90,91,92 ? ----------
Configure it as trunk mode when a switch being able to configure VLAN is connected under it
def-prio Default priority
def-vlan Default VLAN ID
<cr>
Configure the remote management address of the ONU
Confidential▲
ZXAN(config-epon-onu-mng)# mgmt-ip 10.10.10.10 255.255.255.0 vlan 100 priority 7 route

10.0.0.0 255.0.0.0 10.10.10.1 --------Dispatch management address for MDU.
Configure VOIP service
pon-onu-mng epon_onu-1/2/12:1
mgmt-ip 9.144.32.76 255.255.255.240 vlan 47 priority 7 route 0.0.0.0 0.0.0.0 9
.144.32.65
voip rtp-tid tid-number 24 prefix RTP begin-digit 0 align enable digit-length
5 slot 1
voip-module protocol-profile apply h248 domain-mode-default
pon-onu-mng epon_onu-1/3/6:1
auto-config voip enable
voip ip-address 10.132.148.122 mask 255.255.248.0 slot 1
voip rtp-tid tid-number 2 prefix RTP/ begin-digit 0 align enable digit-length
1 slot 1
voip user-tid 1 beginid 1 tid-num 1 prefix A begin-digit 0 align enable digit-
length 1 slot 1
multicast vlan tag-strip port eth_0/1 enable
multicast vlan tag-strip port eth_0/2 enable
voip-module fax-profile apply T38
voip-module global-profile apply vlan voipvlan ip f420-ip
voip-module protocol-profile apply h248 f420-2
Configure multicast service
ZXAN(config)#pon-onu-mng epon_onu-1/2/1:1
ZXAN(config-epon-onu-mng)#multicast vlan port eth_0/1 add vlanlist 4070--Configure multicast
vlan
ZXAN(config-epon-onu-mng)#multicast vlan tag-strip port eth_0/1 enable--Set multicast VLAN
stripping
ZXAN(config-epon-onu-mng)#multicast fastleave enable -------Configure fastleave
5.6.5 Configure service-port
ZXAN(config)#interface vport-1/2/1.1:1 ----------------Enter the vport mode, note that EPON only has
vport 1
ZXAN(config-if-vport-1/2/1.1:1)#service-port 1 user-vlan 41 vlan 33 svlan 584 new-cos 0
Confidential▲
5.6.6 EPON ONU downstream rate-limit
For EPON ONUs, upstream direction rate-limit uses SLA profile, configured under the
interface epon_onu, while downstream rate-limit uses vport or service-port, configured
under the vport mode.
vport rate-limit mode
Traffic-policy rate-limit mode:
Policy rate-limit mode supports to configure upstream/downstream:
ZXAN(config-if-vport-1/2/2.10:1)#qos traffic-policy FTTH_HGU_20M direction egress
Shaping rate-limit mode doesn’t need to configure upstream/downstream:
ZXAN(config-if-vport-1/2/2.10:1)#qos traffic-shaping FTTH_HGU_20M
2)service-port rate-limit mode
Use service-port rate-limit mode as below, mainly limit rate at the egress direction:
ZXAN(config-if-vport-1/2/2.10:1)#service-port 1 user-vlan 100 vlan 100 svlan 1000 egress
FTTH_HGU_20M
6 Configure Port Location
6.1 Configure PPPoE plus
PPPOE+ of the C600 equipment is synchronized with C300V2.1.0, supporting global profiled
configuration, VLAN-based profiled configuration and ONU-based PPPOE+ port location.
ZXAN(config)#port-identification operator-profile profileName ------ Port location profiled

configuration, port location protocol enable / disable, trust rule, Rid enable / disable are all configured
in profile. The information contents of remote id can be set, when it is set as enable, process Rid
according to the bound format profile.
ZXAN(config-portloc-operator-profile-profileName)#pppoe-intermediate-agent ?
disable Set disable
enable Set enable
remote-id Set remote-id
trust Trust set
ZXAN(config-portloc-operator-profile-profileName)#pppoe-intermediate-agent enable
ZXAN(config-portloc-operator-profile-profileName)#pppoe-intermediate-agent trust ?
Confidential▲
false Set false
true Set true
ZXAN(config-portloc-operator-profile-profileName)#pppoe-intermediate-agent remote-id ?
disable Set disable
enable Set enable
format config format profile
ZXAN(config)#pppoe-intermediate-agent vlan 110----Enable (disable) the port location function of

pppoe based on vlan.
ZXAN(config)#show pppoe-intermediate-agent vlan all
vlan total: 1
110
ZXAN(config)#no pppoe-intermediate-agent vlan 110
ZXAN(config)#port-identification operator-profile global profileName----Configure and query port

location operator profile’s global application.
ZXAN(config)#show port-identification operator-profile global
Globally applied operator profile profileName
ZXAN(config)#
6.2 Configure DHCP option82
The option82 of the C600 equipment is synchronized with C300V2.1.0, supporting global profiled
configuration, VLAN-based profiled configuration and ONU-based option82 port location
ZXAN(config)#port-identification operator-profile profileName --------Port location profiled

configuration, port location protocol enable / disable, trust rule, Rid enable / disable are all configured
in profile. The information contents of remote id can be set, when it is set as enable, process Rid
according to the bound format profile.
ZXAN(config-portloc-operator-profile-profileName)#dhcpv4-l2-relay-agent ?
disable Set disable

Confidential▲
enable Set enable
remote-id Set remote-id
trust Trust set
ZXAN(config-portloc-operator-profile-profileName)#dhcpv4-l2-relay-agent enable
ZXAN(config-portloc-operator-profile-profileName)#dhcpv4-l2-relay-agent trust ?
false Set false
true Set true
ZXAN(config-portloc-operator-profile-profileName)#dhcpv4-l2-relay-agent remote-id ?
disable Set disable
enable Set enable
format config format profile
ZXAN(config)#dhcpv4-l2-relay-agent vlan 110 -----Enable (disable) the port location function of dhcp
based on vlan.
ZXAN(config)#show dhcpv4-l2-relay-agent vlan all
vlan total: 1
110
ZXAN(config)#no dhcpv4-l2-relay-agent vlan 110
ZXAN(config)#port-identification operator-profile global profileName -----Configure and query port

location operator profile’s global application.
ZXAN(config)#show port-identification operator-profile global
Globally applied operator profile profileName
ZXAN(config)#
6.3 Configure Remote Id
When adopting ONU interface to configure port location format, except global configurations, you still
need to configure combined format under the ONU interface.
Confidential▲
ZXAN(config-if)#port-identification sub-option remote-id enable ? ------In the ONU interface

configuration management interface, you can enable the remote id function, and can set the protocol
type enabling the function, and enabled interface ( supports sport and vport)
ALL PPPOE DHCPv4 DHCPv6
DHCPv4 DHCPv4
ZXAN(config-if)#port-identification sub-option remote-id ? -------In the ONU interface configuration

management interface, you can set information contents of remote id, directly set remote id
information contents via the name parameter manually; the format parameter means that remote id
information contents can be bound with the format profile.
format configure format profile for remote id
name configure remote id name
Precautions
1)Following configuration examples just show the methods to configure basic port
location function, while for details, refer to Command Manual.
2) By default, port location format profile supported by the system is China Telecom
format, and the profile can be replaced, and can also be self-defined.
7 General Maintenance Operations
7.1 Show Configuration Information
7.1.1 Query un-authenticated ONU
ZXAN#show pon onu uncfg

Query un-authenticated ONUs under the whole OLT, if uncfg-onu-display-info sn loid is
configured under the pon mode, the result shown will comprise SN and LOID.
Confidential▲
7.1.2 Query the configuration under the PON port (Method 1)
ZXAN#show running-config-interface gpon_olt-1/1/1

!<if-intf>
interface gpon_olt-1/1/1
$
!</if-intf>
!<MSAN>
description C600-TESTING
no shutdown
$
!</MSAN>
!<xpon>
onu 1 type 4FE2POS4WLAN loid GPONTEST3
onu 2 type ZTEG-F2866 loid LG0000000010
onu 3 type 4FE2POS4WLAN loid XGPONTEST1
onu 4 type 4FE2POS4WLAN loid test1
onu 5 type 4FE2POS4WLAN loid LG2041178903
$
!</xpon>
7.1.3 Query the configuration under the PON port (Method 2)
ZXAN(config-if-gpon_olt-1/1/1)#show this
!<MSAN>
description C600-TESTING
no shutdown
!</MSAN>
!<xpon>
onu 1 type 4FE2POS4WLAN loid GPONTEST3
onu 2 type ZTEG-F2866 loid LG0000000010
onu 3 type 4FE2POS4WLAN loid XGPONTEST1
onu 5 type 4FE2POS4WLAN loid LG2041178903
!</xpon>
Confidential▲
7.1.4 Query ONU virtual interface and remote management
configuration
ZXAN#show running-config-interface gpon_onu-1/1/1:5

!<if-intf>
$
!</if-intf>
!<xpon>
tcont 1 name Tl1DefaultCreate profile GPON-BW
sn-bind disable
gemport 1 name Tl1OpVlan46 tcont 1
gemport 2 name IPTV tcont 1
$
mvlan 4070
service Tl1OpVlan46 gemport 1 cos 0,1,2,3,4,5,6,7 vlan 46
service IPTV gemport 2 cos 0,1,2,3,4,5,6,7 vlan 2613
$
!</xpon>
7.1.5 View VPORT interface configuration
1)Query VPORT 1 configuration information

ZXAN#show running-config-interface vport-1/1/1.5:1
!<if-intf>
$
!</if-intf>
!<MSAN>
service-port 1 description Tl1OpVlan46
$
!</MSAN>

!<if-intf>
Confidential▲
$
!</if-intf>
!<MSAN>
service-port 2 description IPTV
igmp max-groups 8
$
igmp mvlan 4070
receive-port vport-1/1/1.5:2
$
!</MSAN>

!<if-intf>
$
!</if-intf>
!<MSAN>
$
!</MSAN>

!<if-intf>
$
!</if-intf>
!<MSAN>
$
!</MSAN>

!<if-intf>
$
!</if-intf>
!<MSAN>
$
Confidential▲
!</MSAN>
7.1.6 Query and show service-port configuration according to ONU
ZXAN#show service-port interface gpon_onu-1/1/1:5

Interface gpon_onu-1/1/1:5
Sport Vport CosList BeginVid EndVid OuterVid InnerVid UserPrio Etype Vlan Cos SVlan SCos Tls TlsSVid Ingress Egress
CH Status Enable
-------------------------------------------------------------------------------------------------------------------------------------------
----------
1 1 -- 46 46 -- -- -- -- 4033 -- 3901 -- -- -- -- -- --
OK YES
2 2 -- 2613 2613 -- -- -- -- 2613 -- 3801 -- -- -- -- -- -
- OK YES
3 3 -- 684 684 -- -- -- -- 684 -- 3751 -- -- -- -- -- -
- OK YES
4 4 -- 4001 4001 -- -- -- -- 4001 -- 3850 -- -- -- -- -- -
- OK YES
5 5 -- 4070 4070 -- -- -- -- 4070 -- -- -- -- -- -- -- --
OK YES
Sport total number:
5
7.1.7 Query and show service-port configuration according to vport
ZXAN#show service-port interface vport-1/1/1.5:2

Interface vport-1/1/1.5:2
Sport Vport CosList BeginVid EndVid OuterVid InnerVid UserPrio Etype Vlan Cos SVlan SCos Tls TlsSVid Ingress Egress
CH Status Enable
-------------------------------------------------------------------------------------------------------------------------------------------
----------
2 2 -- 2613 2613 -- -- -- -- 2613 -- 3801 -- -- -- -- -- -
- OK YES
Sport total number:
1
7.1.8 View out-band management configuration
ZXAN(config)#show running-config-interface mgmt_eth

!<if-intf>
interface mgmt_eth
ip address 136.1.1.100 255.255.255.0
Confidential▲
$
!</if-intf>
7.1.9 View VLAN interface configuration
ZXAN(config)#show running-config-interface vlan66

!<if-intf>
interface vlan66
ip address 198.16.63.26 255.255.255.252
$
!</if-intf>
7.1.10 View ONU VEIP VLAN configuration
C600#show gpon remote-onu vlan veip gpon_onu-1/6/1:6

Interface Mode Def-VID Def-Prio Vlan-list
............................................................................
veip_1 trunk -- -- 46,2613
7.1.11 Batched create and show VLAN
ZXAN(config)# vlan list 3010-3110

.....
ZXAN(config)#show vlan summary
All created vlan num: 105
Details are following:
1,100,645,2000,3010-3110
Hardware operate fail following:
7.2 Show Alarms and Logs
7.2.1 View current alarms
ZXAN#show alarm current
Confidential▲
An alarm 723942 ID 643 level 3 occurred at 15:04:36 12-21-2017 sent by ZXAN PFU-1/1/0
%GPONRM% Onu Uni lan los (rack 1 shelf 1 slot 1 port 1 onu 1 uni 1)
%GPON% GPON alarm link olt losi (rack 1 shelf 1 slot 1 port 1 onu 4)
%GPON% GPON alarm channel los (rack 1 shelf 1 slot 1 port 1 channel 2)
%GPON% GPON alarm olt los (rack 1 shelf 1 slot 2 port 1 Probable Cause: LastOnuOffline)
7.2.2 View history alarms
ZXAN#show alarm history

An alarm 722605 ID 638 level 1 occurred at 15:03:45 12-21-2017, cleared at 15:04:33 12-21-2017 sent by ZXAN PFU-1/1/0
%GPONRM% Onu Uni lan los (rack 1 shelf 1 slot 1 port 1 onu 1 uni 1)
%GPON% GPON alarm link olt losi (rack 1 shelf 1 slot 1 port 1 onu 4)
%GPON% GPON alarm channel los (rack 1 shelf 1 slot 1 port 1 channel 2)
... . . .
7.2.3 View alarm records
ZXAN#show logging alarm

A notification 360106 ID 648 level 7 occurred at 23:22:33 12-21-2017 sent by ZXAN MPU-1/11/0
%ADM-MGR% User login! User-account zte login, access type CLI, VTY NO. 1, IP address 198.16.185.2.
%ADM-MGR% User logout! User-account zte logout, access type CLI, VTY NO. 1, IP address 198.24.103.92.
%ADM-MGR% User login! User-account zte login, access type CLI, VTY NO. 1, IP address 198.24.103.92.
.. . . . .
Confidential▲
7.2.4 View operation records
View CLI operation:

C600#show logfile ?
end-time The end time
ipaddress The login IP address
start-time The start time
username The login user name
vtyno The login link number
| Output modifiers
<cr>
C600#show logfile
StartTime: 11:24:14 12-25-2017 EndTime: 11:24:14 12-25-2017 FlowID: 2674 VtyNo: vty1 UserName: zte UserLevel: 15
IP: 198.16.185.2 HostName: ZXAN Result:
success CMDLevel: 0 CMDLine: show pon onu uncfg
success CMDLevel: 0 CMDLine: show pon uncfg-onu-display-info
success CMDLevel: 0 CMDLine: show gpon onu state
success CMDLevel: 15 CMDLine: show cmdgroup 1
7.2.5 View snmp log information
The Snmp log record is Disable by default, first, you need to Enable it:
Under config mode, configure snmp-server log enable all
Command: show logging buffer snmplog
For example:
ZXAN(config)#snmp-server log enable all
ZXAN(config)#show logging buffer snmplog
Log acceptance: on
Log matched: 2
Log in buffer: 2
Buffer occupied: 0.30%
Log file path: /datadisk0/LOG/SNMP/
LogID:3440 2018-01-22 20:08:57.622 Class:Snmp [log-type:LOCAL IP:198.20.160.130 version:v2c

community/user:CQDNC2018 pdu-type:Get request-id:6713780 OID:1.3.6.1.2.1.1.
2.0 OID:1.3.6.1.2.1.1.5.0 OID:1.3.6.1.2.1.1.1.0 error-status:0<NO_ERROR> error-index:0 start-time:12:08:57 01-22-2018 end-
time:12:08:57 01-22-2018]
Confidential▲
LogID:3437 2018-01-22 20:05:50.948 Class:Snmp [log-type:LOCAL IP:198.17.207.37 version:v2c community/user:public pdu-

type:Get request-id:38811809 OID:1.3.6.1.2.1.1.2.0
OID:1.3.6.1.2.1.1.5.0 OID:1.3.6.1.2.1.1.1.0 error-status:0<NO_ERROR> error-index:0 start-time:12:05:50 01-22-2018 end-
time:12:05:50 01-22-2018]
7.2.6 Configure Syslog reporting
ZXAN(config)#logging on
ZXAN(config)#syslog level notifications
ZXAN(config)#syslog-server facility syslog
ZXAN(config)#syslog-server facility local0 ------Configure corresponding facility
ZXAN(config)#syslog-server source ipv4 169.1.5.5 //OLT IP
ZXAN(config)#syslog-server host 192.168.0.100 alarmlog cmdlog snmplog //Address of the syslog server
ZXAN(config)#syslog hostname-field ip-addr
ZXAN(config)#logging ftp notifications vrf mng 168.1.70.100 target target zxralarm.log /*
“zxralarm.log”is the name of the file for saving logs*/----This configuration is optional
7.3 View Equipment Information
7.3.1 View optical module information
ZXAN#show optical-module-info gpon_olt-1/1/1

Optical Module Position: gpon_olt-1/1/1
Optical Module State : online
--------------------------------------------------------------------------------
Optical Module Manufacture Information:
--------------------------------------------------------------------------------
Vendor-Name : SUPERXON LTD. Product-Name: SOGX6292-PSGB-DM
Sequence-Number: 88811170900005 Version-Level: 10
Product-Date: 171102
Part-Number :
Material-Number: N/A
Register-Data: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
--------------------------------------------------------------------------------
Confidential▲
Optical Module Information:

--------------------------------------------------------------------------------
Module-Type : SFP/SFP+ Connector : SC
Supply-Vol : 3.243(v) Temperature : 28.500(c)
Fiber-Type : SM
OTDR : NON-OTDR OTDR-Version:
Module-Class:
--------------------------------------------------------------------------------
Optical Transmitter Information:
--------------------------------------------------------------------------------
Laser-Rate : 25 (100Mb/s) TxPower : 5.247(dbm)
Wavelength : 1577 (nm) TxBias-Current: 100.400(mA)
Laser-Rate : N/A TxPower : N/A
Wavelength : N/A TxBias-Current: N/A
--------------------------------------------------------------------------------
Optical Module Alarm Threshold:
--------------------------------------------------------------------------------
RxPower-Upper : 3 (dbm) RxPower-Lower : -34(dbm)
TxPower-Upper : 9 (dbm) TxPower-Lower : -14(dbm)
Bias-Upper : 131(mA) Bias-Lower : 0(mA)
Voltage-Upper : 7 (v) Voltage-Lower : 0(v)
Temperature-Upper: 90 (c) Temperature-Lower: -45(c)
Module-Class : default
7.3.2 View card software / hardware information of the equipment
ZXAN(config)#show equipment
Slot CfgTpye RealType HardVer McuVer BootVer EpldVer M-Code SN
-------------------------------------------------------------------------------
1 GFBH GFBHK V1.0.0 V1.0.0 V1.0.0 V1.1 000300 711417700006
2 GFXH GFXHK V1.0.0 V1.0.0 V1.0.0 V1.4 000300 713199119911
10 SFUL SFUL V1.0.0 N/A V1.0.0 V1.6 000100 710911000010
11 SFUL SFUL V1.0.0 N/A V1.0.0 V1.6 000100 710911000034
19 XFTO XFTOB V1.0.0 V1.0.0 V1.0.0 V1.1 000100 710802000020
20 PRVR PRVR V1.0.0 V1.0.2 N/A N/A 000001 710647400014
22 PRVR PRVR V1.0.0 V1.0.2 N/A N/A 000001 710647400010
23 FCVD FCVD V1.0.0 V1.0.0P N/A N/A 000101 712221400026
0T1
7.3.3 Show MAC address of the uplink port
ZXAN(config)#show mac interface xgei-1/19/1

Total mac address: 6
Confidential▲
Mac address Vlan Type Port Vc

-------------------------------------------------------------------------------
0025.9ef2.8430 66 Dynamic xgei-1/19/1
0018.8253.8bbb 3751 Dynamic xgei-1/19/1
0018.8253.8bbb 3801 Dynamic xgei-1/19/1
0025.9ef2.8430 3850 Dynamic xgei-1/19/1
0018.8253.8bbb 3901 Dynamic xgei-1/19/1
0018.8253.8bbb 4070 Dynamic xgei-1/19/1
7.3.4 Show route information
ZXAN(config)#show ip forwarding route

IPv4 Routing Table:
Headers: Dest: Destination, Gw: Gateway, Pri: Priority;
Codes: BROADC: Broadcast, USER-I: User-ipaddr, USER-S: User-special,
MULTIC: Multicast, USER-N: User-network, DHCP-D: DHCP-DFT,
ASBR-V: ASBR-VPN, STAT-V: Static-VRF, DHCP-S: DHCP-static,
GW-FWD: PS-BUSI, NAT64: Stateless-NAT64, LDP-A: LDP-area,
GW-UE: PS-USER, P-VRF: Per-VRF-label, TE: RSVP-TE,
BP: BRAS-pool, HAGP: Hybrid-access-gateway-protocol;
Status codes: *valid, >best, R: Relay;
Dest Gw Interface Owner Pri Metric
*> 0.0.0.0/0 198.16.63.25 vlan66 Static 1 0
*> 198.16.63.24/30 198.16.63.26 vlan66 Direct 0 0
*> 198.16.63.26/32 198.16.63.26 vlan66 Address 0 0
7.3.5 Show port optical power index
ZXAN#show performance optical current gpon_olt-1/1/1

----------------------------------------------------------------
RxPower :N/A Supply-Vol :3.175(v)
Temperature :33.988(c)
Channel 1
TxPower :5.085(dbm) Bias-Current:97.792(mA)
Channel 2
TxPower :4.940(dbm) Bias-Current:8.448(mA)
7.3.6 Show status of all interfaces
ZXAN(config)#show ip interface brief

Interface IP-Address Mask Admin Phy Prot
xgei-1/14/1 unassigned unassigned up down down
Confidential▲
xgei-1/14/2 unassigned unassigned down down down

mgmt_eth 10.63.204.235 255.255.255.0 up up up
vlan1 unassigned unassigned up up up
smartgroup1 unassigned unassigned up up down
7.3.7 Show CPU queue message statistics
ZXAN#show control-panel cpu queue statistics

queueId pps ppsPeak pktDropNum peakTime
0 0 2 0 12:20:55 12/18/2018
1 0 0 0 -
2 0 0 0 -
3 0 0 0 -
4 0 0 0 -
5 0 0 0 -
6 0 7 0 12:21:06 12/18/2018
7 26 4853 0 12:16:53 12/18/2018
7.3.8 Show protocol message statistics entering the main control’s CPU
ZXAN#show control-panel packet-limit statistics inband

pktType pktTotal pktDrop pps ppsPeak dropSec peakTime
all 2906 0 0 1 0 12:21:10
12/18/2018
Confidential▲
icmp 0 0 0 0 0 -
ssh 0 0 0 0 0 -
other 0 0 0 0 0 -
igmp 0 0 0 0 0 -
dhcp 0 0 0 0 0 -
pppoe 0 0 0 0 0 -
snmp 0 0 0 0 0 -
telnet 0 0 0 0 0 -
bfd 0 0 0 0 0 -
stp 0 0 0 0 0 -
lacp 0 0 0 0 0 -
lldp 0 0 0 0 0 -
rip 0 0 0 0 0 -
bgp 0 0 0 0 0 -
ospf 0 0 0 0 0 -
isis 0 0 0 0 0 -
ldp 0 0 0 0 0 -
cfm 0 0 0 0 0 -
ipv6_icmp 0 0 0 0 0 -
ipv6_dhcp 0 0 0 0 0 -
raps 0 0 0 0 0 -
mld 0 0 0 0 0 -
erps 0 0 0 0 0 -
ieee1588 0 0 0 0 0 -
pim 0 0 0 0 0 -
ntp 0 0 0 0 0 -
dhcp_bcast 0 0 0 0 0 -
padi 0 0 0 0 0 -
arp_networ 0 0 0 0 0 -
k_side
arp_user_s 2906 0 0 1 0 12:21:10
ide 12/18/2018
ipv6_rs_ne 0 0 0 0 0 -
twork_side
ipv6_rs_us 0 0 0 0 0 -
er_side
ipv6_ra_ne 0 0 0 0 0 -
twork_side
ipv6_ra_us 0 0 0 0 0 -
er_side
ipv6_ns_ne 0 0 0 0 0 -
Confidential▲
twork_side
ipv6_ns_us 0 0 0 0 0 -
er_side
ipv6_na_ne 0 0 0 0 0 -
twork_side
ipv6_na_us 0 0 0 0 0 -
er_side
7.3.9 Show protocol message statistics entering the line card’s CPU
ZXAN#show control-panel packet-limit statistics slot 2

pktType pktTotal pktDrop pps ppsPeak dropSec peakTime
all 37656 0 0 9 0 12:20:30
12/18/2018
icmp 0 0 0 0 0 -
ssh 0 0 0 0 0 -
other 0 0 0 0 0 -
igmp 37656 0 0 9 0 12:20:30
12/18/2018
dhcp 0 0 0 0 0 -
pppoe 0 0 0 0 0 -
snmp 0 0 0 0 0 -
telnet 0 0 0 0 0 -
bfd 0 0 0 0 0 -
stp 0 0 0 0 0 -
lacp 0 0 0 0 0 -
lldp 0 0 0 0 0 -
rip 0 0 0 0 0 -
bgp 0 0 0 0 0 -
ospf 0 0 0 0 0 -
isis 0 0 0 0 0 -
ldp 0 0 0 0 0 -
cfm 0 0 0 0 0 -
ipv6_icmp 0 0 0 0 0 -
ipv6_dhcp 0 0 0 0 0 -
raps 0 0 0 0 0 -
mld 0 0 0 0 0 -
erps 0 0 0 0 0 -
ieee1588 0 0 0 0 0 -
Confidential▲
pim 0 0 0 0 0 -
ntp 0 0 0 0 0 -
dhcp_bcast 0 0 0 0 0 -
padi 0 0 0 0 0 -
arp_networ 0 0 0 0 0 -
k_side
arp_user_s 0 0 0 0 0 -
ide
ipv6_rs_ne 0 0 0 0 0 -
twork_side
ipv6_rs_us 0 0 0 0 0 -
er_side
ipv6_ra_ne 0 0 0 0 0 -
twork_side
ipv6_ra_us 0 0 0 0 0 -
er_side
ipv6_ns_ne 0 0 0 0 0 -
twork_side
ipv6_ns_us 0 0 0 0 0 -
er_side
ipv6_na_ne 0 0 0 0 0 -
twork_side
ipv6_na_us 0 0 0 0 0 -
er_side
ZXAN#
7.4 Performance Statistics
7.4.1 Show Ethernet port performance
ZXAN(config)#show performance eth-if current xgei-1/19/1

----------------------------------------------------------
LinkStatusChanges: 1
Input:
Byte :241357333035 Packets :173769696
UcastPkts :3370206 McastPkts :170399208
BcastPkts :282 OversizePkts :5842
FcsErrors :0 AlignErrs :0
InCrcErrPkts :0 InDiscardPkts:0
Confidential▲
UndersizePkts:0 InErrPkts :0
BwUsingRatio :0%
Output:
Byte :305222136 Packets :921061
UcastPkts :535380 McastPkts :383833
BcastPkts :1848 PausePkts :0
DiscardPkts :0 Collisions :0
SingColls :0 MultiColls :0
OutErrPkts :0
BwUsingRatio :0%
7.4.2 Create VPORT flow statistics
Enable VPORT flow statistics:

ZXAN(config-if-vport-1/1/1.5:5)#performance statistics enable
ZXAN(config-if-vport-1/1/1.5:5)#exit
ZXAN(config)#show performance pon-vport current vport-1/1/1.5:5
--------------------------------------------------------
Input:
Byte :21467 UcastPkts :0
McastPkts :43 BcastPkts :0
Output:
Byte :0 UcastPkts :0
McastPkts :0 BcastPkts :0
Disable VPORT flow statistics:

ZXAN(config-if-vport-1/1/1.5:5)#no performance statistics enable
7.5 Equipment Operations
7.5.1 Reset card
ZXAN#reload ?
slot Reload the designated slot
Confidential▲
system Reload the whole system

ZXAN#reload sl
ZXAN#reload slot ?
1 Shelf number
ZXAN#reload slot 1 ?
<1-23> Slot number
ZXAN#reload slot 1 1 ?
force Force mode
grace Grace mode
ZXAN#reload slot 1 1 f
ZXAN#reload slot 1 1 force
7.5.2 Restart the system
ZXAN#reload system ?
force Force mode
ZXAN#reload system force ?
LINE The description of reload reason (max be 63 characters)
<cr>
ZXAN#reload system force
7.5.3 Show temperature
ZXAN(config)#show temperature detail

-------------------------------------------------------------------------
BoardType: Type of board
I2C : Inter integrated circuit
Addr : Address of check point
Description: Temperature point information
Status : Status of check point
Minor : Slight alarm value (celsius)
Major : Serious alarm value (celsius)
Fatal : Fatal alarm value (celsius)
Overheat: The high-threshold of temperature point (celsius)
Temper : Current temperature (celsius)
-------------------------------------------------------------------------
[shelf 1, slot 1]
BoardType I2C Addr Description Status Minor Major Fatal Overheat Temper
-------------------------------------------------------------------------
GFBH 0 1 cpu Normal 100 108 115 120 48
GFBH 0 2 np temp Normal 100 108 115 120 64
Confidential▲
[shelf 1, slot 2]
-------------------------------------------------------------------------
GFXH 0 1 cpu Normal 100 108 115 120 47
GFXH 0 2 np temp Normal 100 108 115 120 58
[shelf 1, slot 10]

-------------------------------------------------------------------------
SFUL 0 1 mp cpu Normal 100 108 115 120 47
SFUL 0 3 sf3600 Normal 100 108 115 120 51
[shelf 1, slot 11]

-------------------------------------------------------------------------
SFUL 0 1 mp cpu Normal 100 108 115 120 44
SFUL 0 3 sf3600 Normal 100 108 115 120 52
[shelf 1, slot 19]

-------------------------------------------------------------------------
XFTO 0 1 cpu Normal 100 108 115 120 40
XFTO 0 2 np temp Normal 100 108 115 120 61
7.5.4 Show broadcast /unknowncast/multicast packet configuration
ZXAN(config)#show eth-switch
%Error 140305: Incomplete command.
ZXAN(config)#show eth-switch ?
l2cp Show l2cp configuration
l2cp-brief Show l2cp brief configuration
l2cp-default Show default l2cp configuration
max-frame-length show max-frame-length configuration
stormcontrol eth-switch stormcontrol
ZXAN(config)#show eth-switch stormcontrol
pkttype limitnum(unit:pps)
broadcast 100
unknowncast 100
multicast unlimited
7.5.5 Detect rogue ONU
Enable the detection function:

Confidential▲
C600(config-pon)#rogue-onu-detect 6 enable
C600(config-pon)#rogue-onu-detect olt gpon_olt-1/6/1 locate enable auto-shutdown enable
C600(config-pon)#rog
C600(config-pon)#rogue-onu-detect ?
<1-9,12-19> Slot number
olt Configure rogue ONU detect parameter
Show detection information:

ZXAN(config)#show pon rogue-onu-info gpon_olt-1/6/1
Method to restore:
C600(config-if-gpon_olt-1/6/1)#onu-sn enable -----------------Dispatch the command to notify the ONU
to laser.
7.5.6 Show information of the login terminal
ZXAN(config)#show terminal
Line: 66, Location: 136.1.1.111, Type: "vt100"
Length: 36 lines, Width: 168 columns
Telnet idle-timeout: 00:10:00
Telnet absolute-timeout: 1d00h00m
Baud rate (TX/RX):115200/115200
Capabilities: none
Time since activation: 00:06:31
Editing: enabled
History: enabled, History size: 10
Telnet IPv4 ACL name:
Telnet IPv6 ACL name:
Telnet server: enable, Listen port: 23
Telnet DSCP value:
Telnet max-link: 15
7.5.7 Method to connect the ODB port
An ODB port is added on the switching & control card of C600, and it is a port
connected under the Console port on the switching & control card, mainly used for
connection of the line card’s serial port, which can be understood that users can log on
Confidential▲
the serial port of the line card through this port. We can enable or disable the ODB debug
port of a certain slot via CLI .
Note: Before you enable the ODB debug port of a certain slot, please be sure to disable it
first, to avoid from logging in the line card set last time.
ZXAN# odb-switch disable
Enable the ODB debug port of a certain slot:
ZXAN# odb-switch enable slotno 2
View current ODB to enable slot:
ZXAN#show odb-switch
ODB-switch enable on slotno:2
And then connect the serial port cable to the ODB port, login this serial port can log in to
the specified line card’s serial port .
When the ODB port is connected via a serial port cable, it also uses 115200 baud rate.
Confidential▲
7.5.8 Distribute and query TCONT bandwidth
GPON supports to query amount of bandwidth already used, remaining bandwidth,

usage rate percentage of upstream TCONT fixed + assured bandwidth by PON ports via
CLI. Except to query based on single PON port, it still needs to support to use just one
command to query TCONT use states information of all PON ports.
Command: show pon bandwidth dba interface
C600#show pon bandwidth dba interface gpon_olt-1/6/1
interface channel configured(kbps) free(kbps) rate(x.x%)
-------------------------------------------------------------------------------
gpon_olt-1/6/1 1(XG-PON) 52440 2435880 2.1
7.5.9 Modify the length of optical fiber
When the distance exceeds 20KM, the distance of optical fiber needs to be modified:
ZXAN(config-if-gpon_olt-1/1/1)#fiber-distance ?
<0-400> Min distance, unit is 100m, only for GPON
ZXAN(config-if-gpon_olt-1/1/1)#fiber-distance 100 ?
<200-600> Max distance, unit is 100m
ZXAN(config-if-gpon_olt-1/1/1)#fiber-distance 100 300 ?
<cr>
ZXAN(config-if-gpon_olt-1/1/1)#fiber-distance 100 300
7.6 Remote CPU Packet Capturing
7.6.1 CPU packet capturing function based on switching & control
card
Enter the control panel security mode: control-panel

ZXAN#config t
ZXAN(config)#control-panel
ZXAN(config-control-panel)#
Confidential▲
ZXAN(config-control-panel)#snatch-cpu-packet mp enable //Enable the switching & control card’s
cpu packet capturing function
ZXAN(config-control-panel)#write snatch-packet mp //The packet capturing function will be
automatically disabled during the saving process of packets captured
ZXAN (config-control-panel)end
ZXAN# dir //View the file name of the packets captured
ZXAN #copy ftp root: /datadisk0/capture/packetmp.pcap MPU-1/10/0
//10.60.181.21/packetmp.pcap@zte:zte //Upload captured messages to the local PC, MPU-1/x/0, x is
the slot number of the main control
7.6.2 CPU packet capturing function based on line cards
Enter the control panel security mode: control-panel

ZXAN(control-panel)#
ZXAN(control-panel)#snatch-cpu-packet slot 3 enable //Enable the line card’s cpu packet capturing
function
ZXAN(control-panel)#write snatch-packet slot 3 //The packet capturing function will be automatically
disabled during the saving process of packets captured
ZXAN (control-panel)end
ZXAN# dir //View the file name of the packets captured
ZXAN #copy ftp root: /datadisk0/capture/packetnp.pcap MPU-1/10/0
//10.60.181.21/packetnp.pcap@zte:zte //Upload captured messagesk to the local PC

ZXA10 C6XX V1.1.0 Commissioning and General Operation Maintenance Guide V2.0

Uploaded by

Copyright:

Available Formats

ZXA10 C6XX V1.1.0 Commissioning and General Operation Maintenance Guide V2.0

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

ZXA10 C6XX V1.1.0 Commissioning and General Operation Maintenance Guide V2.0

Uploaded by

Copyright:

Available Formats

ZXA10 C6XX V1.1.

and are registered trademarks of ZTE CORPORATION. ZTE’s company name,

Product Version Document Version Serial Number Reason for Revision

Applicable to: Commissioning maintenance personnel

Proposal: Before reading this document, it is recommended to understand the following

2 RELATED DATA PLANNING ........................................................................................ 10

2.1 UPLINK PORT CONFIGURATION REQUIREMENTS ........................................... 10

2.2 GPON/XGPON SERVICE PLANNING...................................................................11

2.2.1 GPON/XGPON ONU SERVICE SCENARIO REQUIREMENTS................... 11

2.2.2 GPON/XGPON BASIC SERVICE SCENARIO CONFIGURATION

2.3 EPON/10EPON SERVICE PLANNING ..................................................................12

2.3.1 EPON/10G EPON SERVICE SCENARIO REQUIREMENTS ........................ 12

2.3.2 EPON/10G EPON BASIC SERVICE SCENARIO CONFIGURATION

2.4 PLANNING OF COMMISSIONING DATA ........................................................... 15

2.4.1 OLT DATA PLANNING ................................................................................ 15

2.4.2 GPON/XPON ONU DATA PLANNING ...................................................... 15

2.4.3 EPON/10GEON ONU DATA PLANNING................................................... 15

3 GLOBAL DATA CONFIGURATION FOR C600 COMMISSIONING ......................... 16

3.2 CREATE USER NAME / PASSWORD FOR C6XX ................................................. 17

3.2.1 CREATE USER NAME / PASSWORD OF LOCAL AUTHENTICATION...... 17

3.2.2 CREATE USER NAME / PASSWORD OF RADIUS AUTHENTICATION .... 18

3.2.3 CONFIGURE USER NAME / PASSWORD OF TACACS AUTHENTICATION19

3.3 ADD PHYSICAL CONFIGURATION ...................................................................... 20

3.4 CONFIGURE OUT-BAND / IN-BAND MANAGEMENT ADDRESS .................... 21

3.4.1 CONFIGURE OUT-BAND MANAGEMENT ADDRESS .............................. 21

3.4.2 CONFIGURE IN-BAND MANAGEMENT ADDRESS AND ROUTE ........... 22

3.5 CREATE LACP SMARTGROUP .............................................................................. 23

3.5.2 CREATE SMARTGROUP AND ADD TO VLAN .......................................... 23

3.5.3 CREATE DYNAMIC SMARTGROUP ........................................................... 23

3.6 CREATE UAPS PROTECTION GROUPS................................................................ 25

3.6.1 CONFIGURE MASTER / SLAVE PROTECTION RELATIONSHIP ............... 25

3.6.2 CONFIGURE UAPS PROTECTION SWITCHING TIME .............................. 26

3.6.3 SET THE TRIGGERING CONDITION FOR UAPS PROTECTION SWITCHING

3.6.4 CONFIGURE UAPS PROTECTION FOR SMARTGROUP ........................... 27

3.7 ADD C600 NE ON EMS ........................................................................................ 29

3.8 MULTICAST GLOBAL CONFIGURATION ............................................................ 30

3.8.1 CONFIGURE THE SLAVE SWITCH AND CONFIGURE MULTICAST GROUP

3.8.2 CONFIGURE MULTICAST SOURCE PORT AND RECEIVE PORT.............. 30

3.8.3 CONFIGURE MULTICAST TO RETRIEVE PACKETS BASED ON VLAN .... 31

3.9 CONFIGURE ACL ...................................................................................................31

3.9.1 CREATE ACL AND RULE.............................................................................. 31

3.9.2 BIND ACL ..................................................................................................... 32

3.9.3 VIEW ALL ACL ENTRIES BOUND ............................................................... 32

3.10 OTHER GLOBAL CONFIGURATIONS...................................................................33

3.10.1 MODIFY THE SYSTEM TIMEZONE AND TIME ........................................ 33

3.10.2 CONFIGURE THE NTP CONNECTION SERVER ....................................... 33

3.10.3 SET TELNET AND SERIAL PORT TIMEOUT TIME .................................... 33

3.10.4 METHOD TO MODIFY THREE-PACKET LIMIT ......................................... 34

3.10.5 SET PORT DELAY DOWN .......................................................................... 34

4 GPON/XGPON ONU COMMISSIONING ...................................................................35

4.1 CREATE ONU TYPE PROFILE ................................................................................ 35

4.1.1 CREATE GENERAL ONU PROFILE .............................................................. 35

4.1.2 SPECIAL CONFIGURATIONS OF ONU PROFILE ....................................... 36

4.2 CREATE GPON TCONT BANDWIDTH PROFILE ................................................. 38

4.3 CREATE VPORT OR SERVICE-PORT RATE-LIMIT BANDWIDTH PROFILE ....... 39

4.4 CONFIGURE VOIP-RELATED PROFILES .............................................................. 39

4.4.1 CREATE IP PROFILE ..................................................................................... 39

4.4.2 CREATE VLAN PROFILE .............................................................................. 40

4.4.3 CONFIGURE VOIP PROTOCOL PROFILE ................................................... 40

4.5 ADD SERVICE VLAN TO OLT UPLINK PORT....................................................... 42