LVP602S

LED Video Processor

USER’S MANUAL
LVP602S User’s Manual

TABLE OF CONTENTS

I. Safety precautions 3

II. Connections of hardware

1.Rear view 4
2. Port description 4

III. Frontal panel operations

1. Diagram of frontal panel 6
2. Button instructions (operation mode) 6

IV. Setup
1. Enter setup of LVP602S 8
2. Select language 9
3. Output image setup 9
4. Brightness / color 11
5. Input image setup 12
6. Audio configurations 15
7. Exit setup 15

V. Specifications 17

VI. Notes to model 18

--------------------------------------------------------------------------------------------------- 2

LED VIDEO PROCESSOR

LVP602S User’s Manual

I. Safety Precautions

Danger!
There is high voltage in the processor, to prevent any unexpected
hazard, unless you are a maintenance, please do not open the cover of the
device.

Warning!
1. This device shall not encounter water sprinkle or splash, please do not
place anything containing water on this device.
2. To prevent fire, keep this device far from any fire source.
3. To keep good ventilation, there shall be at least 20cm interval between
frontal and rear panel of the device.
4. If this device gives out any strange noise, smoke or smell, please
immediately unplug the power cord from receptacle, and contact local
dealer.
5. Please do not plug or unplug DVI signal cable before shutting off
the device.

Caution!
1. Please thoroughly read this manual before using this device, and keep
it well for future reference.
2. In the event of lighting or when you are not going to use the device for
a long time, please pull the power plug out of receptacle.
3. Nobody other than professional technicians can operate the device,
unless they have been appropriately trained or under guidance of
technicians.
4. To prevent equipment damage or electric shock, please don’t fill in
anything in the vent of the device.
5. Do not place the device near any water source or anywhere damp.
6. Do not place the device near any radiator or anywhere under high
temperature.
7. To prevent rupture or damage of power cords, please handle and keep
them properly.
8. Please immediately unplug power cord and have the device repaired,
when
1) Liquid splashes to the device.
2) The device is dropped down or cabinet is damaged.
3) Obvious malpractice is found or performance degrades.
--------------------------------------------------------------------------------------------------- 3

LED VIDEO PROCESSOR

LVP602S User’s Manual

II. Connections of hardware

1. Rear view

Figure 1

2. Port description

1） Video Input

LVP602S supports 8-channel signal input, including:

Port name Description
V1~V2 2-channel PAL/NTSC composite video input
DP(DisplayPort) 1-channel DisplayPort digital HD signal
input
YPbPr 1-channel SD/HD component signal input
VGA 1-channel computer analog signal input
DVI 1-channel computer digital signal input
HDMI 1-channel digital SD/HD signal input
SDI / HDSDI(IN) 1-channel SDI input (SD/HD)

2） Audio Input

LVP602S supports 5-channel stereo audio switch. Of which, 3

channels are DisplayPort, HDMI and SDI audio, the other 2
channels are AD1, AD2 external input audio. AD1 and AD2 can be
mapped to the corresponding audio input of any input among all
video inputs, and will be switched synchronous to the selection of
video input signals.

3） Video Output

Port name Description

VGA OUT 1-channel analog RGBHV signal output, it can be
connected to a local display device and used as
monitor (it is strongly recommended to use this
port when operating and setting LVP602S).

--------------------------------------------------------------------------------------------------- 4

LED VIDEO PROCESSOR

LVP602S User’s Manual

DVI OUT 1 / 2 same DVI digital graphic signal output, it can

DVI OUT 2 be connected with external LED transmission
card or LED transmission box
SDI / HDSDI 1-channel digital video signal loop output
(OUT)

4） Audio Output (AUDIO OUT)

Corresponds to the selected video input signal, output this

channel audio input signals.

5） Signals of other ports

RS232 serial communication port.

--------------------------------------------------------------------------------------------------- 5

LED VIDEO PROCESSOR

LVP602S User’s Manual

III. Frontal panel operations

1. Diagram of frontal panel

Figure 2

2. Button instructions (operation mode):

1) Select input video source

Button names Description

V1, V2 Select V1, V2 BNC port from which signal is
input
DP(DisplayPort) Select DP(DisplayPort) from which signal is
input
YPbPr Select component signal input
VGA Select computer analog signa input
DVI Select computer digital signal input
HDMI Select HDMI digital signal input
SDI Select SDI (HDSDI) digital video signal input
Switch audio input while operating above buttons, select the
audio signal input from corresponding video input to output it
through Audio OUT.
Notes: when user has selected input signal, the current input
signal source that you selected, e.g.: HDMI will appear in the first
line in LCD, and the status of current input signal source will
appear in the second line. If there are no valid signal input, “No
Input” will appear in the screem and dark screen will be displayed
on the LED screen; if the signal is valid, the input signal format,
e.g.: “ 1080p_60Hz ” will appear in the screen.

2) Select output brightness

Button names Description

BRT - Decrease output image brightness of
LVP602S, the lowest brightness is 0.
BRT + Increase output image brightness of LVP602S,

--------------------------------------------------------------------------------------------------- 6

LED VIDEO PROCESSOR

LVP602S User’s Manual

the highest brightness is 64.

LVP602S supports 32 levels Brightness, “0” represents the

lowest brightness, 64 represents the highest brightness. To ensure
full gray level of output image, normally the output brightness is set
as 50!

3) VGA input auto adjustment (Auto)

When the current VGA input source of LVP602S is a valid

signal, press this button, LVP602S will automatically adjust the
sampling parameters of the VGA signals, so as to make VGA
picture clean and complete.
In general, this operation is made only when new VGA signal
source is to be connected in. The time spent in auto adjust depends
on the conditions of signal source, but will be no longer than 1
minutes. Sometimes user need repetitively do such adjustment till
VGA picture looks clean, complete and stable.

4) Information display (Info)

Press this button to view current settings and information of

LVP602S, it consists of 17 items. If you press “Info” again before
LVP602S exit information display, LVP602S will continue to display
the next item of information.

5) Select Full/Part display (Full, Part)

This function only applies to PC input signals (DVI/VGA/DP/HDMI),

user can switch between them. Other input signals can work only in the
full mode.
Button names Description
Full Full means that LED will display a full picture.
Part Part means that LED only display a part of a
picture.

--------------------------------------------------------------------------------------------------- 7

LED VIDEO PROCESSOR

LVP602S User’s Manual

IV. Setup

The following setups must be made by relevant qualified

technicians. For ordinary users, unless they have received adequate
relevant training, they shall not attempt the following setup
operations!
There are 14 items in 5 categories available for you to set in LVP602S.
Technicians can set these items as necessary, for details see the table
below:

Category Items Description

1 Language 1 Language 语言
Selection
2 Output Image 2 Hori_Start Output horizontal start
Setup 3 Hori_Width Output width
4 Vert_Start Output vertical start
5 Vert_Height Output height
6 Out_Format Output resolution
3 Brightness / 7 Brightness
Color 8 Color
4 Input Image 9 Input_Width Width of input image
Setup 10 Input_Height Height of input image
(unadjustable 11 Hori_In_Str Input horizontal start
for this model) 12 Vert_In_Str Input vertical start
5 Audio 13 Audio1 Confi Audio1 configurations
Configurations 14 Audio2 Confi Audio2 configurations
6 16 Device_Init
17 Bias
18 Auto ADC

1. Enter Setup of LVP602S

Press “Setup” for consecutive 8 times while in operation mode,

“ Password: 8 Enter Setup …” will appear in LCD, LVP602S will enter
the No.1 setup item.
After LVP602S enters the setup mode, the 7 buttons on frontal
panel will have the functions as defined in table below:

Name Functions
Step Select step value 2 or 10
--------------------------------------------------------------------------------------------------- 8

LED VIDEO PROCESSOR

LVP602S User’s Manual

↑ Move to last item

↓ Move to next item
← Decrease value or select last value
→ Increase value or select next value
Enter Save the adjustment or selected values
Setup Enter or exit setup mode

After LVP602S enters setup mode, the relevant setup information

will be displayed in LCD as per the layout shown in the figure below:

2 : Hori_Start
？200 Stp=10
Figure 3
1 2 3 4 5

As shown in above figure, LCD consists of five sectors:

Sector Description
1 The No. of current setup item
2 ？: ask you whether to save the adjustment； ！: the
adjustment already be saved and takes effect.
3 Newly adjusted value
4 Step value
5 Name of current setup item

2. Select language

No.1 Item: “Language 语言 ”

After entering setup mode, LVP602S will enter the first setup item
“Language 语言 ”. LVP602S supports Chinese and English display,
press “ ← ” or “ → ” to select either of them, then press “Enter” to save
it and make it valid.

3. Output image setup

LVP602S outputs images from VGA OUT, DVI OUT1 and DVI OUT2.
there are 7 output formats as listed in the table below. User can enter the
No.6 setup item “Out_Format ” to select one fo them.

--------------------------------------------------------------------------------------------------- 9

LED VIDEO PROCESSOR

LVP602S User’s Manual

Format
1 1024×768_60
2 1024×768_75
3 1280×1024_60
4 1280×1024_75
5 1600×1200_60
6 1920×1080_50
7 1920×1080_60

No.6 Item: “Out_Format ”

Press “ ←” or “ →” key to select 1 output format listed under this

option, then press “Enter” to save it.
If you select “1024×768_60”, the output resolution of LVP602S will
be 1024×768, the vertical refresh rate is 60Hz.
However, the resolution of LED screen is not exactly 1024×768
pixels. When the resolution of LED screen is less than 1024×768
pixels, we can set LVP602S to output the images exactly fitting the
resolution of LED screen, so that the LED could display a full frame of
image. See the schematic diagram below:

(0，0)
Vert_Str
Hor_Str Hor_Width

LVP602S Out Image Area

768

Vert_Height
LED Dispaly Screen

LVP602S Out Format = 1024×768

1024

Figure 4

As above figure shows: the size and location of LVP602S output

images are defined by 4 groups of parameters, which correspond to
four setup items respectively, for details of their relationship see Table 5
below:

--------------------------------------------------------------------------------------------------- 10

LED VIDEO PROCESSOR

LVP602S User’s Manual

No. of setup item Setup Item Name Names of parameters

2 Hori_Start Hor_Str
3 Hori_Width Hor_Width
4 Vert_Start Vert_Str
5 Vert_Height Vert_Height

The start coordinates (0, 0) of LVP602S output image is defined in

the right_top of 1024×768 pixels output area.
Set the four setup items as listed in above table as per the size of
current LED screen (pixels) and start position of the input image that
LED displays. Press “↑” or “↓” to select setup item, press “ ←” or
“ →” to increase or decrease the values of current item. Press “Enter”
to save the settings.

4. Brightness / Color

No.7 setup item: “Brightness ”

LVP602S supports 32 levels Brightness, “0” represents the lowest

brightness, 64 represents the highest brightness.
Press “ ←” or “ →” to increase or decrease the values of
brightness. Press “Enter” to save the settings.
To ensure full gray level of output image, normally the output
brightness is set as 50 !

No.8 Item: “Color ”

For V1, V2, DP, YPbPr and HDMI video input source, LVP602S can
set color saturation ranging between 32-64. The lower this value is, the
weaker the color looks; the higher this value is, the stronger the color
looks. Press “ ←” or “ →” to increase or decrease the values of color
saturation. Press “Enter” to save the settings.
Normally the value of color saturation is set as 50 !

--------------------------------------------------------------------------------------------------- 11

LED VIDEO PROCESSOR

LVP602S User’s Manual

5. Input image setup

Items 9-12 are the menus for multiple machine to work

together in parallel, they don’t apply to LVP602S.

Items No. Item Name

9 Input_Width
10 Input_Height
11 Hori_In_Str
12 Vert_In_Str

6. Audio configurations

LVP602S supports 5-channel stereo audio switch. Of which, 3

channels are DisplayPort, HDMI and SDI audio, the other 2
channels are AD1, AD2 external input audio. AD1 and AD2 can be
mapped to the corresponding audio input of any input among all
video inputs, and will be switched synchronous to the selection of
video input signals.
If HDMI (or DP, SDI) is configured with external input audio,
when you switch it, external input audio will be selected, otherwise
the aidio signals contained in HDMI (or DP, SDI) will selected as input.

Item 13: “ AD1 audio configurations ”

Press “ ←” or “ →” to select 1 channel of video input signals from

all input signals, map AD1 external input as audio input signals to the
video signals in this channe, then press “ Enter” to save the settings.

Item 14：“ AD2 audio configurations ”

Press “ ←” or “ →” to select 1 channel of video input signals from
all input signals, map AD2 external input as audio input signals to the
video signals in this channe, then press “ Enter” to save the settings.
Note: AD1, AD2 can’t be mapped to the video input signals in
the same channel.

7. Exit setup

Item 15: “Exit setup ”

Press “↓” to move to the last option “exit setup”, press “ ←” or
--------------------------------------------------------------------------------------------------- 12
LED VIDEO PROCESSOR
LVP602S User’s Manual

“ →” to select “YES”, press “Enter” to exit setup.

Press “Setup” while in any setup mode, the system will directly skip
to item 15.

8. Factory settings
The following are settings made in factory area, improper settings
or improper operations in this area may result in malfunction of the
processor, we recommend users to make these operate following the
directions of technicians of manufacturers.

Item 16: “ Reset ”

When the system skips to item 15 from item 14, press “V1” for 5
times, then press “↓” to move to item 16 “Reset”, press “ ←” or
“ →” to select “YES”, press “Enter”, the processor will resume
default settings which were made in factory, and the system will remind
you “please shut off / power on again”, please operate following the
indications.

Item 17: “Bias”

In order to reduce the noise of screen, LED large screen system

usually removes low-scale noise, but this will results in loss of image
information, especially those dark pictures like night views.
LVP602S can maje corrections by adjusting “Bias”, the limit value
ranges between 32-64. In the event signals of dark screen are missing,
increase this value, the missing information will appear on large LED
screen.
In order to ensure complete output gray, the standard value is set
to be 50!

Item 18: “Auto ADC”

The processor without calibrating white balance may suffer color

cast or low brightness when it is connected with analog signals.
LVP602S can automatically adjust white balance based on the analog
signals input (including AV, YPbPr and VGA) to solve the above
problems. The procedures of “Auto ADC” are as below:
Shift to corresponding analog input signals, when the processor
detects input signals and output it to display, enter the item 18 optiom
of setup menu, press “ ←” or“ →” to select “YES”, press “Enter”,
the processor will calibrate white balance.
Note: as processor has calibrated white balance using standard
--------------------------------------------------------------------------------------------------- 13

LED VIDEO PROCESSOR

LVP602S User’s Manual

signals in the factory, please don’t use the function of this option unless
necessary.

--------------------------------------------------------------------------------------------------- 14

LED VIDEO PROCESSOR

LVP602S User’s Manual

V. Specifications

Inputs
Numbs/Type 2×composite video
1×DP(Display Port)
1×YPbPr
1×VGA (RGBHV)
1×DVI
1×HDMI
1×SDI ( HDSDI )
Video system PAL/NTSC
Composite Video 1V (p_p) / 75Ω
Scope/Impedance
VGA Format PC（VESA） ≤1600x1200 @60HZ
VGA Scope/Impedance R、G、B = 0.7 V (p_p) / 75Ω
DVI Format SD/HD(EIA-861B) ≤1920x1080P @60HZ
PC(VESA) ≤1600x1200 @60HZ
HDMI Format SD/HD(EIA-861B) ≤1920x1080P @60HZ
( HDCP ) PC(VESA) ≤1600x1200 @60HZ
DP Format SD/HD(EIA-861B) ≤1920x1080P @60HZ
PC(VESA) ≤1600x1200 @60HZ
YPbPr Format SD/HD(EIA-861B) ≤1920x1080P @60HZ
YPbPr Y= -0.3V ~ +0.7V (p_p) / 75Ω
Scope/Impedance Pb= -0.35V ~ +0.35V (p_p) / 75Ω
Pr= -0.35V ~ +0.35V (p_p) / 75Ω
SDI Format SDI-SMPTE 259M-C 576i @50HZ
480i @60HZ
HDSDI Format HDSDI-SMPTE 292M 1080i @50HZ/60HZ
SMPTE 274M/296M 720P @60HZ
Input Connectors VGA：15pin D_Sub(Female)
DVI：24+1 DVI_D
YPbPr: BNC×3
Composite video：BNC
D/P: Display Port
SDI/HDSDI: BNC
Outputs
Nums/Type 1×VGA ( RGBHV)
2×DVI
VGA/DVI Format 1024×768@60Hz/75Hz

--------------------------------------------------------------------------------------------------- 15

LED VIDEO PROCESSOR

LVP602S User’s Manual

1280×1024@60Hz/75Hz
1600×1200@60Hz
1920×1080p@50Hz/60Hz
VGA Scope/Impedance R、G、B = 0.7 V (p_p) / 75Ω
Output Connectors VGA：15pin D_Sub(female)
DVI OUT1：24+5 DVI_I
DVI OUT2：24+1 DVI_D
Others
Control Panel Button
Power 100-240VAC 60W 50/60Hz
Operating Temp 5-40 ℃
Humidity 15-85%
Size 155 mm (high) ×350mm (wide) ×
485mm (length)
Weight 5.6 Kg

VI. Notes to model

LVP602S: with SDI / HDSDI input interface.

LVP602: without SDI / HDSDI input interface. So all instructions
regarding SDI、HDSDI in above don’t apply to LVP602!

--------------------------------------------------------------------------------------------------- 16

LED VIDEO PROCESSOR