LOAD CHARTS

RT700E
CAPACITY 70TON
85% STABILITY
ON OUTRIGGERS
75% STABILITY
ON RUBBER

224707
SERIAL NUMBER

RT760E - S/N 224707 1

RT760E - S/N 224707 2
 TABLE OF CONTENTS

GENERAL NOTES ................................................................................................ 4

WEIGHT REDUCTIONS / LINE PULLS & REEVING INFO.................................. 5
LIFTING AREA DIAGRAMS .................................................................................. 6
RANGE DIAGRAM ................................................................................................ 7

ON OUTRIGGERS FULLY EXTENDED

MAIN BOOM .................................................................................................... 8
EXTENSION .................................................................................................... 9

ON RUBBER ................................................................................................. 10-11

ON OUTRIGGERS 50% EXTENDED

MAIN BOOM .................................................................................................. 13
EXTENSION .................................................................................................. 14

ON OUTRIGGERS 0% EXTENDED
MAIN BOOM .................................................................................................. 15

TIRE INFLATION................................................................................................. 16

RT760E - S/N 224707 3

 NOTES FOR LIFTING CAPACITIES
GENERAL:
1. Rated loads as shown on lift chart pertain to this machine as originally manufactured and equipped. Modifications to the machine or use
of optional equipment other than that specified can result in a reduction of capacity.
2. Construction equipment can be hazardous if improperly operated or maintained. Operation and maintenance of this machine shall be in
compliance with the information in the Operator’s and Safety Handbook, Service Manual, and Parts Manual supplied with this machine.
If these manuals are missing, order replacements from the manufacturer through the distributor.
3. The operator and other personnel associated with machine shall fully acquaint themselves with the latest American National Safety
Standards (ASME/ANSI) for cranes.
SETUP:
1. The machine shall be level and on a firm supporting surface. Depending on the nature of the supporting surface, it may be necessary
to have structural supports under the outrigger floats or tires to spread the load to a larger bearing surface.
2. For outrigger operation, all outriggers shall be properly extended with tires raised free of crane weight before operating the boom or
lifting loads.
3. When machine is equipped with center front stabilizer, the front stabilizer shall be set in accordance with instructions in Operator's &
Safety Handbook.
4. When equipped with removable and/or extendible counterweight, the proper counterweight shall be installed and fully extended before
and during operation.
5. Tires shall be inflated to the recommended pressure before lifting on rubber.
6. With certain boom and hoist tackle combinations, maximum capacities may not be obtainable with standard cable lengths.
7. Unless approved by the crane manufacturer, do not travel with boom extension or jib erected. Refer to Operator's and Safety Handbook
for job-site travel information.
OPERATION:
1. Rated loads at rated radius shall not be exceeded. Do not attempt to tip the machine to determine allowable loads. For clamshell,
grapple, magnet or concrete bucket operation, weight of componentt and load must not exceed 80% of rated lifting capacities.
2. All rated loads have been tested to and meet the requirements of SAE J1063 - Cantilevered Boom Crane Structures - Method of Test,
and do not exceed 85% of the tipping load on outriggers fully extended. Capacities on outriggers 50% extended and 0% extended (fully
retracted) correspond to SAE J1289 (Test Load = 1.25P + 0.1A). 0.1A represents one-tenth (0.10) of the total boom weight reduced to
the boom point. Loads are also determined by SAE J765 Crane Stability Test Code.
3. Rated loads include the weight of hookblock, slings and auxiliary lifting devices and their weights shall be subtracted from the listed
rating to obtain the net load to be lifted. When more than the minimum required parts of line needed to pick the load are used, the
additional rope weight as measured from the lower sheaves of the the main boom nose shall be considered part of the load to be lifted.
When both the hook block and headache ball are reeved, the lifting device that is NOT in use, including the line as measured from the
lower sheave(s) of the nose supporting the unused device shall be considered part of the load.
4. Load ratings are based on freely suspended loads. No attempt shall be made to move a load horizontally on the ground in any direction.
5. The maximum in-service wind speed is 20 m.p.h. It is recommended when wind velocity is above 20 m.p.h., rated loads and boom
lengths shall be appropriately reduced. For machines not in-service, the main boom should be retracted and lowered with swing brake
set in wind velocities over 30 m.p.h.
6. Rated loads are for lift crane service only.
7. Do not operate at a radius or boom length where capacities are not listed. At these positions, the machine may overturn without any
load on the hook.
8. The maximum load which can be telescoped is not definable because of variations in loadings and crane maintenance, but it is safe to
attempt retraction and extension of the boom within the limits of the capacity chart.
9. When the boom length or lift radius or both are between values listed, the smallest load shown at either the next larger radius or next
longer or shorter boom length shall be used.
10. For safe operation, the user shall make due allowances for his particular job conditions, such as: soft or uneven ground, out of level
conditions, high winds, side loads, pendulum action, jerking or sudden stopping of loads, experience of personnel, two machine
(tandem) lifts, traveling with loads, electric wires, obstacles, hazardous conditions, etc. Side pull on boom or jib is extremely dangerous.
11. Regardless of counterweight and outrigger spread configuration, no deduct is required from the main boom charts for a stowed boom
extension.
12. Never handle personnel with this machine unless the requirements of the applicable national, state, and local regulations and safety
codes are met.
13. Keep load handling devices a minimum of 42 inches below boom head at all times.
14. The boom angle before loading should be greater than the loaded boom angle to account for deflection.
15. Capacities appearing above the bold line are based on structural strength and tipping should not be relied upon as a capacity limitation.
16. Capacities for the 36 ft. boom length shall be lifted with boom fully retracted. If boom is not fully retracted, capacities shall not exceed
those shown for the 40 ft. boom length.
17. When operating in the "On Outriggers 50% Extended (17' 4" spread)" mode, the outrigger beam pins must be engaged. When
operating in the "On Outriggers 0% Extended (10' 5" spread)" mode, the outrigger beams must be fully retracted. Failure to follow these
precautions could result in structural damage or loss of stability of the machine.
18. Do not lift loads when boom is fully lowered. The Load Moment Indicator (LMI) senses pressure and will not provide warnings or
lockout. The crane can become overloaded if lift cylinder(s) is fully retracted.
19. WARNING: Lifting with the 33 ft. extension base, with the 23 ft. extension fly either erected or folded along side of extension base, is
strictly prohibited.
20. The maximum outrigger pad load is 80,800 lb.
DEFINITIONS:
1. Operating Radius: Horizontal distance from a projection of the axis of rotation to the supporting surface before loading to the center of
the vertical hoist line or tackle with load applied.
2. Loaded Boom Angle (Shown in Parenthesis on Main Boom Capacity Chart): is the angle between the boom base section and the
horizontal, after lifting the rated load at the rated radius with the rated boom length.
3. Working Area: Areas measured in a circular arc about the center line of rotation as shown on the working area diagram.
4. Freely Suspended Load: Load hanging free with no direct external force applied except by the lift cable.
5. Side Load: Horizontal force applied to the lifted load either on the ground or in the air.

RT760E - S/N 224707 4

 WEIGHT REDUCTIONS FOR LOAD HANDLING DEVICES
33 FT. - 56 FT. When lifting over swingaway and/or jib combina-
FOLDING BOOM EXTENSION tions, deduct total weight of all load handling
devices reeved over main boom nose directly
*33 ft. Extension (Erected) - 5,080 lb. from swingaway or jib capacity.
*56 ft. Extension (Erected) - 11,330 lb.
*Reduction of main boom capacities NOTE: All load handling devices and boom at-
(no deduct required for stowed boom extension) tachments are considered part of the load and
suitable allowances MUST BE MADE for their
combined weights. Weights are for Grove fur-
AUXILIARY BOOM NOSE 137 lb. nished equipment.
HOOKBLOCKS and HEADACHE BALLS:
60 Ton, 5 Sheave 1250 lb.+
50 Ton, 4 Sheave 1000 lb.+
50 Ton, 3 Sheave 1000 lb.+
8.3 Ton Headache Ball (non-swivel) 350 lb.+
8.3 Ton Headache Ball (swivel) 370 lb.+
+Refer to rating plate for actual weight.

LINE PULLS AND REEVING INFORMATION

PERMISSIBLE NOMINAL
HOISTS CABLE SPECS.
LINE PULLS CABLE LENGTH

3/4" (19 mm) 6x37 Class

Main EIPS, IWRC Special Flexible 16,800 lb. 500 ft.
Min. Breaking Str. 58,800 lb.
3/4" (19 mm) 35x7 Class
Main & Aux. Rotation Resistant (non-rotating) 16,800 lb. 500 ft.
Min. Breaking Strength 85,800 lb.
The approximate weight of 3/4" wire rope is 1.5 lb./ft.

HOIST PERFORMANCE
Hoist Line Pulls Drum Rope
Wire Capacity (ft.)
Two Speed Hoist
Rope
Low High 16 in. drum 26 in. drum
Layer
Available lb.* Available lb.* Layer Total Layer Total
1 18,134 9,067 78 78 132 132
2 16,668 8,334 85 164 144 276
3 15,420 7,710 92 256 156 432
4 14,347 7,174 99 356 167 599
5 13,413 6,707 106 462 179 778
6 12,594 6,297 113 575 190 968
*Max. lifting capacity: 6x37 and 35x7 class = 16,800 lb.

RT760E - S/N 224707 5

RT760E - S/N 224707 6
RT760E - S/N 224707 7
 RATED LIFTING CAPACITIES IN POUNDS
36 FT. - 110 FT. BOOM
ON OUTRIGGERS FULLY EXTENDED - 360°
Radius #0001
in Main Boom Length in Feet
Feet
36 40 50 **60 70 80 90 100 110
140,000 84,400 80,200 *62,500
10
(69) (72) (76) (78)
100,000 84,400 80,200 62,500 *36,800
12
(65.5) (68.5) (73.5) (77) (78)
85,400 82,700 80,200 61,000 36,800 *36,800 *31,000
15
(59.5) (63.5) (70) (74) (76.5) (78) (78)
65,700 65,000 64,300 50,650 36,800 36,800 31,000 *29,100 *24,000
20
(49) (55) (63.5) (69) (72) (75) (77) (78) (78)
52,800 52,450 51,850 41,800 36,800 34,000 30,000 27,000 24,000
25
(36) (45) (56.5) (63.5) (68) (71) (73.5) (76) (77.5)
42,150 39,600 38,000 33,400 29,000 25,300 24,200 22,000
30
(31.5) (48.5) (57.5) (63) (67) (70.5) (72.5) (75)
31,750 29,750 28,700 25,000 22,200 21,750 20,000
35
(40) (51.5) (58) (63) (67) (69.5) (72)
24,450 24,750 23,600 22,000 20,200 19,000 18,500
40
(28) (45) (53) (59) (63) (66.5) (69)
See 19,750 19,700 18,800 17,800 17,300 17,300
45
Note 16 (37) (47.5) (54.5) (59.5) (63) (66.5)
16,000 16,750 16,500 16,000 16,000 16,000
50
(26.5) (41) (49.5) (55.5) (60) (63.5)
13,650 14,300 14,100 14,100 14,100
55
(33.5) (44.5) (51) (56.5) (60)
11,150 12,000 12,200 12,200 12,200
60
(24) (38.5) (47) (52.5) (57)
10,100 10,800 10,600 10,600
65
(31.5) (42) (48.5) (53.5)
8,480 9,410 9,000 9,000
70
(22.5) (36.5) (44.5) (50)
8,100 7,800 7,800
75
(30) (40) (46.5)
6,920 6,600 6,600
80
(21.5) (34.5) (42.5)
5,800 5,800
85
(28.5) (38)
5,000 5,000
90
(20.5) (33)
4,440
95
(27.5)
3,880
100
(19.5)
Minimum boom angle (°) for indicated length (no load) 0
Maximum boom length (ft.) at 0° boom angle (no load) 110
NOTE: ( ) Boom angles are in degrees.
#LMI operating code. Refer to LMI manual for operating instructions.
*This capacity is based on maximum boom angle.
Lifting Capacities at Zero Degree Boom Angle
On Outriggers Fully Extended - 360°
Boom Main Boom Length in Feet
Angle 36 40 50 **60 70 80 90 100 110
29,050 24,450 17,050 11,950 9,400 7,310 6,050 4,660 3,350
0°
(29.8) (34.2) (44.2) (54.6) (64.2) (74.2) (84.2) (94.2) (104.2)
NOTE: ( ) Reference radii in feet. A6-829-101070
** Boom length is with inner-mid fully extended and outer-mid & fly fully retracted.
RT760E - S/N 224707 8
 33 FT. - 56 FT. FOLDING BOOM EXTENSION
ON OUTRIGGERS FULLY EXTENDED - 360°
33 ft. LENGTH 56 ft. LENGTH NOTES:
Radius
0° 25° 45° 0° 25° 45°
in
Feet
OFFSET OFFSET OFFSET OFFSET OFFSET OFFSET 1. All capacities above the bold line are
#0021 #0022 #0023 #0041 #0042 #0043 based on structural strength of boom
12,900
30
(78)
extension and do not exceed 85% of
35
12,900 *8,330 tipping loads, in accordance with SAE
(76) (78)
J765.
12,900 *10,850 8,330
40
(74) (78) (77.5)
12,900 10,450 *7,410 8,330
2. 33 ft. and 56 ft. boom extension
45
(72) (77) (78) (76) lengths may be used for single line
12,100 10,000 7,200 8,330
50
(70) (74.5) (77.5) (74.5)
lifting service.
11,100 9,220 6,990 8,250 *5,300
55
(68) (72.5) (75) (73) (78) 3. Radii listed are for a fully extended
60
10,100 8,550 6,800 7,540 5,140 boom with the boom extension
(66) (70.5) (72.5) (71) (77)
9,130 7,930 6,650 7,160 5,100 *3,860
erected. For main boom lengths less
65
(63.5) (68) (70.5) (69) (75) (78) than fully extended, the rated loads
8,460 7,380 6,490 6,820 5,100 3,790
70
(61.5) (65.5) (68) (67.5) (73) (77.5)
are determined by boom angle. Use
7,840 6,900 6,370 6,300 4,800 3,660 only the column which corresponds
75
(59) (63) (65.5) (65.5) (71) (75)
to the boom extension length and
7,230 6,470 6,110 5,810 4,580 3,550
80
(56.5) (60.5) (62.5) (63.5) (69) (73) offset for which the machine is con-
85
6,690 6,070 5,780 5,370 4,470 3,450 figured. For boom angles not shown,
(54) (58) (60) (61.5) (67.5) (71)
6,140 5,720 5,480 4,980 4,330 3,410
use the rating of the next lower boom
90
(51) (55.5) (57) (59.5) (65.5) (68.5) angle.
5,670 5,400 5,200 4,630 4,070 3,300
95
(48.5) (52.5) (54) (57) (63) (66.5) WARNING: Operation of this ma-
5,020 5,100 4,950 4,320 3,830 3,260
100
(45.5) (49.5) (51) (55) (61) (64) chine with heavier loads than the
105
4,350 4,760 4,650 4,040 3,620 3,220 capacities listed is strictly prohibited.
(42.5) (46.5) (47.5) (52.5) (58.5) (62)
3,750 4,160 3,770 3,410 3,180
Machine tipping with boom extension
110
(39.5) (43) (50.5) (56) (59.5) occurs rapidly and without advance
3,210 3,600 3,540 3,230 3,060
115
(36) (39.5) (48) (53.5) (56.5)
warning.
2,720 3,100 3,300 3,050 2,940
120
(32) (35) (45.5) (51) (53.5) 4. Boom angle is the angle above or
125
2,270 2,640 2,870 2,890 2,800 below horizontal of the longitudinal
(27.5) (30.5) (42.5) (48.5) (50.5)
1,860 2,470 2,730
axis of the boom base section after
130
(22) (39.5) (45.5) lifting rated load.
2,110 2,590
135
(36.5) (42.5) 5. Capacities listed are with outriggers
1,770 2,250
140
(33) (38.5) fully extended and vertical jacks set
145
1,460 1,880 only.
(29.5) (34.5)
1,170
150
(25)
Minimum boom angle
(°) for indicated length 21 25 45 25 28 45
(no load)
Maximum boom length
(ft.) at 0° boom angle 100 90
(no load)
NOTE: ( ) Boom angles are in degrees. A6-829-101289
#LMI operating code. Refer to LMI manual for operating instructions.
*This capacity is based upon maximum boom angle.

RT760E - S/N 224707 9

 ON RUBBER CAPACITIES

STATIONARY CAPACITIES STATIONARY CAPACITIES

360° DEFINED ARC OVER FRONT (See Note 3)
#9005 #9005
Radius Radius
in Main Boom Length in Feet in Main Boom Length in Feet
Feet Feet
36 40 50 *60 70 36 40 50 *60 70
45,300 39,700 45,300 42,850 29,600
10 10
(69) (72) (69) (72) (76)
41,750 39,700 29,600 43,650 41,350 29,600
12 12
(65.5) (68.5) (73.5) (65.5) (68.5) (73.5)
29,350 26,450 26,450 20,900 38,300 36,300 29,600 20,900 17,300
15 15
(59.5) (63.5) (70) (74) (59.5) (63.5) (70) (74) (76.5)
17,800 17,650 17,050 16,250 16,250 31,150 29,550 25,900 20,900 17,300
20 20
(49) (55) (63.5) (69) (72) (49) (55) (63.5) (69) (72)
11,750 11,700 11,350 10,850 10,850 24,100 24,150 21,800 18,800 17,300
25 25
(36) (45) (56.5) (63.5) (68) (36) (45) (56.5) (63.5) (68)
8,040 7,820 7,470 7,470 17,400 17,200 15,300 15,300
30 30
(31.5) (48.5) (57.5) (63) (31.5) (48.5) (57.5) (63)
5,400 5,120 5,120 12,800 12,500 11,000
35 35
(40) (51.5) (58) (40) (51.5) (58)
3,660 3,200 3,430 9,720 9,390 9,390
40 40
(28) (45) (53) (28) (45) (53)
1,000 2,150 7,090 7,090
45 45
(37) (47.5) (37) (47.5)
1,150 5,310 5,310
50 50
(41.0) (26.5) (41)
NOTE: ( ) Reference boom angles in degrees. 3,870
55
Lifting Capacities at Zero Degree Boom Angle (33.5)
On Rubber - Stationary 360 3,170
60
(24)
Boom Main Boom Length in Feet
NOTE: ( ) Reference boom angles in degrees.
Angle 36 40 50
Lifting Capacities at Zero Degree Boom Angle
8,180 5,890 2,170 On Rubber - Defined Arc Over Front
0°
(29.7) (34.2) (44.2)
Boom Main Boom Length in Feet
Note: ( ) Reference radii in feet. A6-829-101048A
Angle 36 40 50 *60 70
#LMI operating code. Refer to LMI manual for instructions.
*60 ft. boom length is with inner-mid extended and outer-mid & fly 17,600 13,600 7,750 4,010 2,670
0°
retracted. (29.7) (34.2) (44.2) (54.6) (64.2)
Note: ( ) Reference radii in feet. A6-829-101047
#LMI operating code. Refer to LMI manual for instructions.
*60 ft. boom length is with inner-mid extended and outer-mid & fly
retracted.

No Load Stability Data 60 ft. 70 ft.

Main Boom Main Boom
Front Min. boom angle (deg.) for indicated length ----- 0
(No Load) Max. boom length (ft.) at 0 deg. boom angle ----- 70
360° Min. boom angle (deg.) for indicated length 32 37
(No Load) Max. boom length (ft.) at 0 deg. boom angle 50 50

RT760E - S/N 224707 10

 ON RUBBER CAPACITIES (cont'd.)

PICK & CARRY CAPACITIES (UP TO 2.5 MPH) -

NOTES TO ALL RUBBER CAPACITY
BOOM CENTERED OVER FRONT (See note 7)
CHARTS:
#9006
Radius
in
1. Capacities are in pounds and do not
Main Boom Length in Feet
Feet exceed 75% of tipping loads as deter-
36 40 50 *60 70
mined by test in accordance with SAE
42,500 37,600 30,700 J765.
10
(69) (72) (76)
42,500 37,600 30,700 23,450 2. Capacities are applicable to machines
12
(65.5) (68.5) (73.5) (77) equipped with 29.5x25 (28 ply) tires at
15
37,600 37,600 30,700 19,700 16,250 65 psi cold inflation pressure.
(59.5) (63.5) (70) (74) (76.5)
32,950 32,900 30,700 19,700 16,250 3. Defined Arc - Over front includes 6° on
20 either side of longitudinal centerline of
(49) (55) (63.5) (69) (72)
24,100 24,150 23,850 19,700 16,250 machine (ref. drawing C6-829-003529).
25
(36) (45) (56.5) (63.5) (68)
4. Capacities appearing above the bold
17,400 17,200 16,800 16,250
30
(31.5) (48.5) (57.5) (63) line are based on structural strength and
12,800 12,500 12,500
tipping should not be relied upon as a
35 capacity limitation.
(40) (51.5) (58)
9,720 9,390 9,390 5. Capacities are applicable only with ma-
40
(28) (45) (53)
chine on firm level surface.
7,090 7,090
45
(37) (47.5) 6. On rubber lifting with boom extensions
50
5,310 5,310 not permitted.
(26.5) (41)
3,870 7. For pick and carry operation, boom must
55 be centered over front of machine, me-
(33.5)
3,090 chanical swing lock engaged and load
60
(24) restrained from swinging. When han-
NOTE: ( ) Reference boom angles in degrees. dling loads in the structural range with
Lifting Capacities at Zero Degree Boom Angle
capacities close to maximum ratings,
On Rubber - Pick & Carry travel should be reduced to creep
Main Boom Length in Feet speeds.
Boom
Angle 36 40 50 *60 70 8. Axle lockouts must be functioning when
0°
17,600 13,600 7,750 4,010 2,670 lifting on rubber.
(29.7) (34.2) (44.2) (54.6) (64.2)
Note: ( ) Reference radii in feet. A6-829-101049 9. All lifting depends on proper tire infla-
#LMI operating code. Refer to LMI manual for instructions.
tion, capacity and condition. Capacities
*60 ft. boom length is with inner-mid extended and outer-mid & fly must be reduced for lower tire inflation
retracted. pressures. See lifting capacity chart for
tire used. Damaged tires are hazardous
to safe operation of crane.
10. Creep - not over 200 ft. of movement in
any 30 minute period and not exceeding
1 mph.

RT760E - S/N 224707 11

RT760E - S/N 224707 12
 RATED LIFTING CAPACITIES IN POUNDS
36 FT. - 110 FT. BOOM
ON OUTRIGGERS 50% EXTENDED (17' 4" spread) - 360°
Radius #4001
in Main Boom Length in Feet
Feet
36 40 50 **60 70 80 90 100 110
109,000 84,400 80,200 *62,500
10
(69) (72) (76) (78)
96,750 84,400 80,200 52,500 *36,800
12
(65.5) (68.5) (73.5) (77) (78)
82,150 81,850 80,200 52,500 36,800 *36,800 *31,000
15
(59.5) (63.5) (70) (74) (76.5) (78) (78)
56,650 54,800 51,200 48,150 36,800 36,800 31,000 *29,100 *24,000
20
(49) (55) (63.5) (69) (72) (75) (77) (78) (78)
36,850 34,800 34,550 33,800 33,800 33,550 30,000 27,000 24,000
25
(36) (45) (56.5) (63.5) (68) (71) (73.5) (76) (77.5)
24,150 24,150 24,150 25,100 25,500 25,300 24,200 22,000
30
(31.5) (48.5) (57.5) (63) (67) (70.5) (72.5) (75)
17,650 17,800 18,700 19,550 20,100 20,100 20,000
35
(40) (51.5) (58) (63) (67) (69.5) (72)
See 13,250 13,500 14,300 15,100 15,900 16,350 16,350
40
Note 16 (28) (45) (53) (59) (63) (66.5) (69)
10,400 11,150 11,900 12,650 13,050 13,450
45
(37) (47.5) (54.5) (59.5) (63) (66.5)
8,050 8,770 9,480 10,150 10,550 10,950
50
(26.5) (41) (49.5) (55.5) (60) (63.5)
6,880 7,570 8,240 8,600 8,960
55
(33.5) (44.5) (51) (56.5) (60)
5,340 6,030 6,680 7,020 7,350
60
(24) (38.5) (47) (52.5) (57)
4,760 5,390 5,710 6,030
65
(31.5) (42) (48.5) (53.5)
3,670 4,310 4,620 4,920
70
(22.5) (36.5) (44.5) (50)
3,400 3,690 3,990
75
(30) (40) (46.5)
2,580 2,900 3,180
80
(21.5) (34.5) (42.5)
2,200 2,480
85
(28.5) (38)
1,570 1,860
90
(20.5) (33)
1,310
95
(27.5)
0.1A (lb.) 1,050 1,060 1,100 1,120 1,030 970 920 880 840
Minimum boom angle (°) for indicated length (no load) 0
Maximum boom length (ft.) at 0° boom angle (no load) 110
NOTE: ( ) Boom angles are in degrees.
#LMI operating code. Refer to LMI manual for operating instructions.
*This capacity is based on maximum boom angle.
Lifting Capacities at Zero Degree Boom Angle
On Outriggers 50% Extended - 360°
Boom Main Boom Length in Feet
Angle 36 40 50 **60 70 80 90 100
26,350 18,250 10,400 6,260 4,230 2,870 1,970 1,090
0°
(29.8) (34.2) (44.2) (54.6) (64.2) (74.2) (84.2) (94.2)
NOTE: ( ) Reference radii in feet. A6-829-101072B
** Boom length is with inner-mid fully extended and outer-mid & fly fully retracted.
RT760E - S/N 224707 13
 33 FT. - 56 FT. FOLDING BOOM EXTENSION
ON OUTRIGGERS 50% EXTENDED (17' 4" spread) - 360°
33 ft. LENGTH 56 ft. LENGTH
Radius
0° 25° 45° 0° 25° 45°
in
OFFSET OFFSET OFFSET OFFSET OFFSET OFFSET
Feet
#4021 #4022 #4023 #4041 #4042 #4043
12,900
30
(78)
12,900 *8,330
35
(76) (78)
12,900 *10,850 8,330
40
(74) (78) (77.5)
12,900 10,450 *7,410 8,330
45
(72) (77) (78) (76)
11,100 10,000 7,200 8,330
50
(70) (74.5) (77.5) (74.5)
9,430 9,220 6,990 8,250 *5,300
55
(68) (72.5) (75) (73) (78)
8,010 8,550 6,800 7,540 5,140
60
(66) (70.5) (72.5) (71) (77)
6,820 7,930 6,650 7,060 5,100 *3,860
65
(63.5) (68) (70.5) (69) (75) (78)
5,800 6,770 6,490 6,060 5,100 3,790
70
(61.5) (65.5) (68) (67.5) (73) (77.5)
4,920 5,700 6,080 5,200 4,800 3,660
75
(59) (63) (65.5) (65.5) (71) (75)
4,140 4,770 5,140 4,440 4,580 3,550
80
(56.5) (60.5) (62.5) (63.5) (69) (73)
3,460 3,970 4,320 3,770 4,470 3,450
85
(54) (58) (60) (61.5) (67.5) (71)
2,780 3,260 3,600 3,180 4,330 3,410
90
(51) (55.5) (57) (59.5) (65.5) (68.5)
2,180 2,640 2,970 2,650 3,770 3,300
95
(48.5) (52.5) (54) (57) (63) (66.5)
1,640 2,080 2,400 2,140 3,190 3,260
100
(45.5) (49.5) (51) (55) (61) (64)
1,160 1,590 1,890 1,670 2,670 3,220
105
(42.5) (46.5) (47.5) (52.5) (58.5) (62)
1,140 1,260 2,190 2,630
110
(43) (50.5) (56) (59.5)
1,730 2,090
115
(53.5) (56.5)
1,300 1,610
120
(51) (53.5)
1,160
125
(50.5)
0.1A (lb.) 810 750 710 770 710 650
Minimum boom angle
(°) for indicated length 30 31 45 39 40 45
(no load)
Maximum boom length
(ft.) at 0° boom angle 90 80
(no load)
NOTE: ( ) Boom angles are in degrees. A6-829-101290
#LMI operating code. Refer to LMI manual for operating instructions.
*This capacity is based upon maximum boom angle.
NOTES:
1. All capacities above the bold line are based on structural strength of boom extension.
2. 33 ft. and 56 ft. boom extension lengths may be used for single line lifting service.
3. Radii listed are for a fully extended boom with the boom extension erected. For main boom lengths less than fully
extended, the rated loads are determined by boom angle. Use only the column which corresponds to the boom extension
length and offset for which the machine is configured. For boom angles not shown, use the rating of the next lower boom
angle.
WARNING: Operation of this machine with heavier loads than the capacities listed is strictly prohibited. Machine tipping
with boom extension occurs rapidly and without advance warning.
4. Boom angle is the angle above or below horizontal of the longitudinal axis of the boom base section after lifting rated
load.
5. Capacities listed are with outriggers properly extended and vertical jacks set only.
RT760E - S/N 224707 14
 RATED LIFTING CAPACITIES IN POUNDS
36 FT. - 110 FT. BOOM

ON OUTRIGGERS 0% EXTENDED (10' 5" spread) - 360°

Radius #8001
in Main Boom Length in Feet
Feet
36 40 50 **60 70 80 90 100 110
82,500 78,750 71,650 *62,500
10
(69) (72) (76) (78)
62,700 60,200 55,350 51,250 *36,800
12
(65.5) (68.5) (73.5) (77) (78)
44,950 43,500 40,300 37,600 36,800 *36,150 *31,000
15
(59.5) (63.5) (70) (74) (76.5) (78) (78)
27,150 25,600 25,050 24,500 24,800 24,650 24,400 *24,050 *23,600
20
(49) (55) (63.5) (69) (72) (75) (77) (78) (78)
18,100 16,400 16,200 16,000 16,950 17,800 17,850 17,750 17,600
25
(36) (45) (56.5) (63.5) (68) (71) (73.5) (76) (77.5)
10,950 10,950 10,950 11,750 12,650 13,450 13,550 13,500
30
(31.5) (48.5) (57.5) (63) (67) (70.5) (72.5) (75)
7,440 7,580 8,350 9,140 9,910 10,350 10,550
35
(40) (51.5) (58) (63) (67) (69.5) (72)
See 4,950 5,190 5,910 6,640 7,360 7,780 8,190
40
Note 16 (28) (45) (53) (59) (63) (66.5) (69)
3,390 4,080 4,770 5,450 5,840 6,210
45
(37) (47.5) (54.5) (59.5) (63) (66.5)
1,990 2,650 3,320 3,970 4,330 4,680
50
(26.5) (41) (49.5) (55.5) (60) (63.5)
1,510 2,160 2,790 3,120 3,450
55
(33.5) (44.5) (51) (56.5) (60)
1,210 1,820 2,140 2,450
60
(38.5) (47) (52.5) (57)
1,010 1,320 1,620
65
(42) (48.5) (53.5)
0.1A (lb.) 1,050 1,060 1,100 1,120 1,030 970 920 880 840
Minimum boom angle (°) for indicated length (no load) 15 28 34 40
Maximum boom length (ft.) at 0° boom angle (no load) 70
NOTE: ( ) Boom angles are in degrees.
#LMI operating code. Refer to LMI manual for operating instructions.
*This capacity is based on maximum boom angle.
Lifting Capacities at Zero Degree Boom Angle
On Outriggers 0% Extended - 360°
Boom Main Boom Length in Feet
Angle 36 40 50
12,700 7,680 3,240
0°
(29.8) (34.2) (44.2)
NOTE: ( ) Reference radii in feet. A6-829-101073A
** Boom length is with inner-mid fully extended and outer-mid & fly fully retracted.

RT760E - S/N 224707 15

 TIRE INFLATION - PSI (BAR)

SIZE LIFTING SERVICE , GENERAL

(FRONT TRA TRAVEL AND EXTENDED TRAVEL
& CODE
REAR) STATIC, CREEP &
2.5 MPH (4.0 km/h)

MICHELIN
___ 75 (5.2)
29.5R25 XHA

29.5x25 (28 or 34) E-3 65 (4.5)

General/Titan, (See operator's manual for
Denman Broadway extended roading.)
/ Rock Plus

RT760E - S/N 224707 16