52-1

GROUP 52

INTERIOR AND
SUPPLEMENTAL
RESTRAINT
SYSTEM (SRS)
CONTENTS

INTERIOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52A

SUPPLEMENTAL RESTRAINT SYSTEM (SRS) . . . . . . . . . . . . 52B

52A-2

GROUP 52A

INTERIOR
CONTENTS

GENERAL INFORMATION . . . . . . . . 52A-3 INSIDE REAR VIEW MIRROR . . . . . . 52A-15

GENERAL DESCRIPTION . . . . . . . . . . . . . 52A-3 REMOVAL AND INSTALLATION . . . . . . . . 52A-15

SEAT BELT DIAGNOSIS. . . . . . . . . . 52A-3 FRONT SEAT ASSEMBLY. . . . . . . . . 52A-15

SEAT BELT WARNING SYSTEM DIAGNOSIS REMOVAL AND INSTALLATION . . . . . . . . 52A-15
...................................... 52A-3 DISASSEMBLY AND ASSEMBLY . . . . . . . 52A-16
INSPECTION. . . . . . . . . . . . . . . . . . . . . . . . 52A-18
SPECIAL TOOLS. . . . . . . . . . . . . . . . 52A-3
REAR SEAT ASSEMBLY. . . . . . . . . . 52A-20
INSTRUMENT PANEL ASSEMBLY . 52A-4 REMOVAL AND INSTALLATION . . . . . . . . 52A-20
REMOVAL AND INSTALLATION . . . . . . . 52A-4 DISASSEMBLY AND ASSEMBLY . . . . . . . 52A-21
DISASSEMBLY AND ASSEMBLY . . . . . . . 52A-10
FRONT SEAT BELT . . . . . . . . . . . . . . 52A-22
FLOOR CONSOLE ASSEMBLY . . . . 52A-11 REMOVAL AND INSTALLATION . . . . . . . . 52A-22
REMOVAL AND INSTALLATION . . . . . . . . 52A-11 INSPECTION. . . . . . . . . . . . . . . . . . . . . . . . 52A-22

TRIMS. . . . . . . . . . . . . . . . . . . . . . . . . 52A-12 REAR SEAT BELT . . . . . . . . . . . . . . . 52A-23

REMOVAL AND INSTALLATION . . . . . . . 52A-12 REMOVAL AND INSTALLATION . . . . . . . . 52A-23

HEADLINING . . . . . . . . . . . . . . . . . . . 52A-14 SPECIFICATIONS . . . . . . . . . . . . . . . 52A-24

REMOVAL AND INSTALLATION . . . . . . . . 52A-14 FASTENER TIGHTENING SPECIFICATIONS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52A-24

WARNINGS REGARDING SERVICING OF SUPPLEMENTAL RESTRAINT SYSTEM (SRS) EQUIPPED VEHICLES

WARNING
• Improper service or maintenance of any component of the SRS, or any SRS-related component, can lead to
personal injury or death to service personnel (from inadvertent firing of the air bag) or to the driver and
paassenger (from rendering the SRS inoperative).
• Service or maintenance of any SRS component or SRS-related component must be performed only at an
authorized MITSUBISHI dealer.
• MITSUBISHI dealer personnel must thoroughly review this manual, and especially its GROUP 52B - Supplemental
Restraint System (SRS) before beginning any service or maintenance of any component of the SRS or any SRS-
related component.
NOTE
The SRS includes the following components: SRS air bag control unit, SRS warning light, front impact sensors, air bag module,
clock spring, and interconnecting wiring. Other SRS-related components (that may have to be removed/installed in connection
with SRS service or maintenance) are indicated in the table of contents by an asterisk (*).
 INTERIOR 52A-3
GENERAL INFORMATION

G ENER A L IN FO R M ATIO N
GENERAL DESCRIPTION
M1523000100038

OPERATION
Seat belt warning system
• When the ignition switch is turned "ON" without fastening the seat belts (seat belt switch OFF), the tone
alarm will sound for approximately 6 seconds to warn the driver to fasten the seat belts.When the seat
belts are fastened, the torn alarm will stop sounding.
• When the ignition switch is turned ON without fastening the seat belt, the seat belt warning light comes on
to warn the driver to fasten the seat belt.

SEAT B ELT DIA G N O SIS

SEAT BELT WARNING SYSTEM DIAGNOSIS
M1521000700078
The seat belt warning system is controlled by Simplified Wiring System (SWS). For troubleshooting, refer to
GROUP 54B, SWS Diagnosis P.54B-104.

SPECIAL TO O LS
M1521000600071

TOOL TOOL NUMBER AND SUPERSESSION APPLICATION

NAME
MB990784 General service tool Removal of switch, trim,
Ornament remover etc.

MB990784

TSB Revision
52A-4 INTERIOR
INSTRUMENT PANEL ASSEMBLY

TOOL TOOL NUMBER AND SUPERSESSION APPLICATION

NAME
MB991502 MB991496-OD Checking the ETACS-
Scan tool (MUT-II) ECU input signal

B991502

MB991529 Tool not necessary if Checking the ETACS-

Diagnostic trouble code scan tool (MUT-II) is ECU input signal
check harness available (When using the
voltmeter)
MB991529

A MB991223 MB991223 Measurement of terminal

A: MB991219 voltage
B: MB991220
C: MB991221
D: MB991222
B Harness set
A: Test harness
B: LED harness
C: LED harness
C D: Probe

MB991223AE

IN STRU M ENT PA N EL A SSEM BLY

REMOVAL AND INSTALLATION
M1521001700071

WARNING
For removal and installation of the passenger's side air bag module, always observe the
service procedures described in GROUP 52B, Air Bag Module and Clock Spring P.52B-67.
The bolts and screws described below are used for installation of the instrument panel. They are indicated by
symbols in the illustration.

TSB Revision
 INTERIOR 52A-5
INSTRUMENT PANEL ASSEMBLY

NAME SYMBOL SIZE (D × L) mm (in) COLOR SHAPE

Tapping screw a 4 × 12 (0.16 × 0.47) -
b 5 × 16 (0.20 × 0.63) -
ACX01283AB

c 5 × 12 (0.20 × 0.45) -
d 5 × 16 (0.20 × 0.63) -
e 5 × 12 (0.20 × 0.45) Black ACX01282

f 5 × 16 (0.20 × 0.63)
g 5 × 20 (0.20 × 0.79) -

ACX01284

h 5 × 20 (0.20 × 0.79) Black

AC003137

Washer assembled bolt i 6 × 16 (0.24 × 0.63) -

j 6 × 20 (0.24 × 0.79)
ACX02229

k 6 × 16 (0.24 × 0.63) -

AC001594

D: Thread diameter L: Effective thread length

TSB Revision
52A-6 INTERIOR
INSTRUMENT PANEL ASSEMBLY

15 17
d 19
d 20
18
d
4 16 18
h f
g
5
3 1
7
8 1
f
f
d
d
2 d
e

9
d d
d
6
10
d
a
14
13
11 12 AC003138AB

REMOVAL STEPS REMOVAL STEPS (Continued)

1. INSTRUMENT PANEL SIDE COVER 10. HEATER CONTROL ASSEMBLY
2. HOOD LOCK RELEASE HANDLE (REFER TO GROUP 55, HEATER
3. SWITCH PANEL ASSEMBLY CONTROL ASSEMBLY AND A/C
4. CONNECTOR HOLDER SWITCH P.55-26.)
5. FRONT DRIVER'S SIDE UNDER 11. GLOVE BOX STRIKER
COVER 12. GLOVE BOX
6. CENTER PANEL ASSEMBLY 13. FRONT PASSENGER'S UNDER
• FOOT DISTRIBUTION DUCT COVER PLUG
(REFER TO GROUP 55, 14. FRONT PASSENGER'S SIDE
VENTILATORS P.55-43.) UNDER COVER
7. CENTER AIR OUTLET ASSEMBLY 15. RHEOSTAT (REFER TO GROUP
8. HAZARD WARNING LIGHT SWITCH 54A, RHEOSTAT P.54A-80.)
(REFER TO GROUP 54A, HAZARD 16. METER BEZEL
WARNING LIGHT SWITCH P.54A- 17. COMBINATION METER
81.) 18. SIDE DEFROSTER GRILLE
9. RADIO AND TAPE PLAYER 19. SPEAKER GRILLE
• FRONT PILLAR TRIM (REFER TO
P.52A-12.)
20. INSTRUMENT PANEL UPPER PLUG

TSB Revision
 INTERIOR 52A-7
INSTRUMENT PANEL ASSEMBLY

21 24

22
i
j
i
i
23 26 i
25
k j
i i
27

23
AC003139AB

REMOVAL STEPS REMOVAL STEPS (Continued)

• FRONT PILLAR TRIM (REFER TO 24. KNEE ABSORBER (DRIVER'S SIDE)
P.52A-12.) 25. KNEE ABSORBER (PASSENGER'S
21. AIR BAG MODULE (PASSENGER'S SIDE)
SIDE) 26. AUTO-CRUISE CONTROL-ECU
22. INSTRUMENT PANEL ASSEMBLY 27. INSTRUMENT PANEL CENTER
23. SIDE AIR OUTLET ASSEMBLY REINFORCEMENT

TSB Revision
52A-8 INTERIOR
INSTRUMENT PANEL ASSEMBLY

CLIP AND CLAW POSITIONS

G
H

H
F B
F G

B
B
A
B

C
A
B
C
D
NOTE D
: Clip position
: Claw position

SECTION A – A SECTION B – B SECTION C – C SECTION D – D

INSTRUMENT INSTRUMENT PANEL
FRONT PASSENGER'S
PANEL ASSEMBLY SIDE COVER, CENTER SIDE UNDER COVER (CLAW)
PANEL ASSEMBLY

FRONT
FRONT PASSENGER'S
CLIP FRONT PASSENGER'S INSTRUMENT FRONT PASSENGER'S UNDER COVER
CLIP
SIDE UNDER COVER PANEL ASSEMBLY PASSENGER'S SIDE UNDER PLUG (CLAW)
UNDER COVER PLUG COVER
SECTION E – E SECTION F – F SECTION G – G SECTION H – H
SIDE DEFROSTER GRILLE FRONT DRIVER'S SIDE FRONT DRIVER'S SIDE
SWITCH PANEL UNDER COVER UNDER COVER
ASSEMBLY

CLIP
CLAW FRONT
DRIVER'S CLAW
INSTRUMENT SIDE UNDER INSTRUMENT
PANEL ASSEMBLY COVER PANEL ASSEMBLY
AC003140AB

TSB Revision
 INTERIOR 52A-9
INSTRUMENT PANEL ASSEMBLY

M
J
I K M

J I L LK

NOTE
: Claw position

SECTION I – I SECTION J – J SECTION K – K SECTION L – L

INSTRUMENT
INSTRUMENT PANEL ASSEMBLY
METER BEZEL
METER BEZEL CLAW PANEL UPPER PLUG
CLAW

CLAW

CLAW
INSTRUMENT INSTRUMENT INSTRUMENT INSTRUMENT
PANEL ASSEMBLY PANEL ASSEMBLY PANEL ASSEMBLY PANEL UPPER PLUG
SECTION M – M

INSTRUMENT SPEAKER GRILLE

PANEL ASSEMBLY

CLAW

AC003141AB

TSB Revision
52A-10 INTERIOR
INSTRUMENT PANEL ASSEMBLY

DISASSEMBLY AND ASSEMBLY

M1521001900075

c
1
c 2

c
c
1

c
4
c

3
c
b

AC003142AB

DISASSEMBLY STEPS DISASSEMBLY STEPS (Continued)

1. SIDE DEFROSTER DUCT 4. SPEAKER PANEL
2. DEFROSTER DUCT 5. AIR BAG REINFORCEMENT
3. DISTRIBUTION DUCT 6. INSTRUMENT PANEL

TSB Revision
 INTERIOR 52A-11
FLOOR CONSOLE ASSEMBLY

FLO O R CO NSO LE A SSEM BLY

REMOVAL AND INSTALLATION
M1521002200079

<VEHICLES
1 WITH ARMREST>
8
9 5 4 <VEHICLES
WITHOUT ARMREST>
A
C
3 2
A
C B
B

SECTION A – A

SHIFT LEVER PANEL ASSEMBLY

10
11

NOTE
: Clip position CLIPS

SECTION B – B SECTION C – C
CUP TRAY CENTER LOWER PANEL ASSEMBLY

CLIPS CLIP

AC003143AB

REMOVAL STEPS REMOVAL STEPS (Continued)

1. SHIFT LEVER PANEL ASSEMBLY 6. TRAY BRACKET A <VEHICLES
2. CUP TRAY <VEHICLES WITHOUT WITH ARMREST>
ARMREST> 7. FLOOR CONSOLE
3. CUP HOLDER BOTTOM PANEL 8. CENTER LOWER PANEL
4. ARMREST ASSEMBLY <VEHICLES ASSEMBLY
WITH ARMREST> 9. ASHTRAY
5. CUP HOLDER BOTTOM PANEL 10. CONSOLE BRACKET C
11. CONSOLE BRACKET A

TSB Revision
52A-12 INTERIOR
TRIMS

TR IM S
REMOVAL AND INSTALLATION
M1521001100079

D
D
E 6
4
E
F
D 22 N·m
F
16 ft-lb
C D
C
D D 9

2 10
5 11
3 A
12
1 13
A 7

B
B
8 H
G

G
H

5 N·m
NOTE 44 in-lb
: Clip position
: Claw position

SECTION A – A SECTION B – B SECTION C – C SECTION D – D

CLIP REAR
SCUFF PLATE PILLAR CLIP
FRONT
PILLAR TRIM TRIM

CLIP CLAW
COWL SIDE TRIM

SECTION E – E SECTION F – F SECTION G – G SECTION H – H

CLIP REAR SHELF FRONT
CLIP SHELF COVER
CLIP
TRIM

REAR
PILLAR
TRIM
CLIP
REAR PILLAR TRIM
AC003718AB

TRIMS REMOVAL STEPS TRIMS REMOVAL STEPS

1. FRONT SCUFF PLATE 7. REAR SHELF TRIM
2. REAR SCUFF PLATE 8. SHELF FRONT COVER
3. COWL SIDE TRIM UPPER TETHER ANCHOR
4. FRONT PILLAR TRIM REMOVAL STEPS
5. CENTER PILLAR LOWER TRIM 9. TETHER ANCHOR BRACKET
6. REAR PILLAR TRIM 10. COVER

TSB Revision
 INTERIOR 52A-13
TRIMS

UPPER TETHER ANCHOR

REMOVAL STEPS (Continued)
11. SPACER 10mm (0.4 inch)
12. SPACER 7mm (0.3 inch)
13. FIBER WASHER

15

17
L
14 L
I

J
K

J K

18 16

NOTE
: Clip position

SECTION I – I SECTION J – J SECTION K – K SECTION L – L

REAR END
TRIM COVER
TRUNK TRIM
CLIP CLIP ASSEMBLY

TRUNK TRIM CLIP

ASSEMBLY
CLIP
TRUNK FRONT TRIM

AC003145AB

REMOVAL STEPS REMOVAL STEPS (Continued)

14. TRUNK FRONT TRIM 17. REAR END TRIM COVER
15. CORNER PLATE 18. TRUNK FLOOR BOARD
16. TRUNK TRIM ASSEMBLY

TSB Revision
52A-14 INTERIOR
HEADLINING

HEA DLIN IN G
REMOVAL AND INSTALLATION
M1521001400070

Pre-removal and Post-installation Operation

• Front Pillar Trim, Center Pillar Lower Trim and Rear Pillar
Trim Removal and Installation (Refer to P.52A-12.)

8
7

A A

5
2
9

SECTION A – A
4 CLIP

HEADLINING
3
AC003146AB

REMOVAL STEPS REMOVAL STEPS (Continued)

1. SUNVISOR ASSEMBLY 6. FRONT ROOF PAD
2. SUNVISOR HOLDER 7. REAR ROOF PAD
3. DOME LIGHT ASSEMBLY 8. HEADLINING TRIM <VEHICLES
4. SUNROOF SWITCH COVER WITH SUNROOF>
<VEHICLES WITH SUNROOF> 9. HEADLINING
5. COAT HANGER

TSB Revision
 INTERIOR 52A-15
INSIDE REAR VIEW MIRROR

IN SID E REA R VIEW M IRR O R

REMOVAL AND INSTALLATION
M1521002700074
Insert a narrow flat-tip screwdriver into the slit in the inside rear
view mirror in the direction of the arrow in the illustration.
BUTTON
NOTE: While the spring is pushed in, connection between the
spring and the pawl of the button is released.
BRACKET

SPRING

SLIT AC000333 AB

FRO NT SEAT ASSEM B LY

REMOVAL AND INSTALLATION
M1522001300076

WARNING
Before removing a seat equipped with a side air bag module, refer to GROUP 52B, SRS
Service Precautions P.52B-15.
1

2 1

3
44 N·m
33 ft-lb 3
2
44 N·m
33 ft-lb
2

44 N·m
2 33 ft-lb

44 N·m
29 N·m 33 ft-lb
21 ft-lb

2
29 N·m
AC003147AB
21 ft-lb

TSB Revision
52A-16 INTERIOR
FRONT SEAT ASSEMBLY

1. HEAD RESTRAINT FRONT SEAT ASSEMBLY

REMOVAL STEPS
• HARNESS CONNECTOR
2. SEAT ANCHOR COVER
>>A<< 3. FRONT SEAT ASSEMBLY

INSTALLATION SERVICE POINT

>>A<< FRONT SEAT ASSEMBLY INSTALLATION
First install all of the front seat assembly mounting nuts and
bolts, and then tighten them to the specified torque.
DISASSEMBLY AND ASSEMBLY
M1522001500100

<WITHOUT POWER SEAT> 12

14 13 15 16

11

7 9
44 N·m
33 ft-lb
10
18
22 N·m
16 ft-lb
17
N

5
22 N·m
6 16 ft-lb

4
1
12 N·m
106 in-lb
19 2
3 AC003663AB

DISASSEMBLY STEPS DISASSEMBLY STEPS (Continued)

1. RECLINING ADJUSTER KNOB 9. FRONT SEAT CUSHION PAD
2. CLIP 10. FRONT SEAT CUSHION FRAME
3. HEIGHT ADJUSTER KNOB <<A>> 11. FRONT SEATBACK PANEL
4. FRONT SEAT SHIELD COVER 12. FRONT SEATBACK ASSEMBLY
5. FRONT SEAT SHIELD COVER 13. HEADRESTRAINT GUIDE
6. INNER SEAT BELT 14. FRONT SEATBACK COVER
7. FRONT SEAT CUSHION ASSEMBLY 15. FRONT SEATBACK PAD
8. FRONT SEAT CUSHION COVER

TSB Revision
 INTERIOR 52A-17
FRONT SEAT ASSEMBLY

DISASSEMBLY STEPS (Continued)

16. FRONT SEATBACK FRAME
<VEHICLES WITHOUT SRS SIDE
AIR BAG>
17. FRONT SEAT INNER COVER
18. FRONT SEAT INNER COVER
19. FRONT SEAT ADJUSTER
ASSEMBLY

<POWER SEAT> 14

16 15 17 18

13

10
9
5 11 8 6
12 7
20
22 N·m
16 ft-lb
N 3 19
2
21
22 N·m
44 N·m
16 ft-lb
33 ft-lb

22 4
12 N·m
106 in-lb 1 AC003665AB

DISASSEMBLY STEPS DISASSEMBLY STEPS (Continued)

1. FRONT SEAT SHIELD COVER 10. FRONT SEAT CUSHION COVER
2. FRONT SEAT SHIELD COVER 11. FRONT SEAT CUSHION PAD
3. INNER SEAT BELT 12. FRONT SEAT CUSHION FRAME
4. BOLT <<A>> 13. FRONT SEATBACK PANEL
5. FRONT SEAT CUSHION ASSEMBLY 14. FRONT SEATBACK ASSEMBLY
6. FRONT SEAT RECLINING 15. HEADRESTRAINT GUIDE
ADJUSTER LEVER 16. FRONT SEATBACK COVER
7. FRONT SEAT SLIDE ADJUSTER 17. FRONT SEATBACK PAD
LEVER 18. FRONT SEATBACK FRAME
8. GARNISH <VEHICLES WITHOUT SRS SIDE
9. POWER SEAT SWITCH AIR BAG>

TSB Revision
52A-18 INTERIOR
FRONT SEAT ASSEMBLY

DISASSEMBLY STEPS (Continued)

19. FRONT SEAT INNER COVER
20. FRONT SEAT INNER COVER
21. POWER SEAT HARNESS
22. POWER SEAT ADJUSTER
ASSEMBLY

DISASSEMBLY SERVICE POINT

<<A>> FRONT SEATBACK PANEL REMOVAL
1. Using a screwdriver or similar tool, push in the clip of the
front seatback panel lower portion to remove it.
CLIP
2. Pull down the front seatback panel to remove it.

FRONT SEATBACK PANEL

AC000337AB

INSPECTION
M1522001600044
POWER SEAT SWITCH CONTINUITY CHECK
RECLINING
SWITCH

SLIDE AND
HEIGHT SWITCH

AC003150AB

SWITCH POSITION TESTER CONNECTION SPECIFIED CONDITION

Reclining switch Forward 3−13, 4−14 Continuity
Backward 3−14, 4−13 Continuity
Slide switch Forward 8−13, 7−14 Continuity
Back ward 7−13, 8−14 Continuity
Front height switch Up 5−14, 6−13 Continuity
Down 5−13, 6−14 Continuity
Rear height switch Up 1−13, 2−14 Continuity
Down 1−14, 2−13 Continuity
All switches OFF − No continuity

POWER SEAT MOTOR OPERATION CHECK

Inspect the operation of each motor according to the following
procedures.
1. Disconnect the connector for each motor.

TSB Revision
 INTERIOR 52A-19
REAR SEAT ASSEMBLY

2. When the battery is connected directly to the motor

terminals, check if the motors run smoothly, and check if
RECLINING MOTOR each setting mechanism runs in the direction shown in the
CONNECTOR REAR HEIGHT table below for each motor.
MOTOR CONNECTOR
(1) Connect the battery power source to the terminal 3 and
ground the terminal 4 for the front/rear height down side
and connect the battery power source to the terminal 4
and ground the terminal 3 for the front/rear height up
side.
(2) Connect the battery power source to the terminal 1 and
ground the terminal 2 for the slide backward side and
connect the battery power source to the terminal 2 and
ground the terminal 1 for the slide forward side.
(3) Connect the battery power source to the terminal 2 and
ground the terminal 1 for the reclining backward side and
connect the battery power source to the terminal 1 and
SLIDE MOTOR FRONT HEIGHT
ground the terminal 2 for the reclining forward side.
CONNECTOR MOTOR
CONNECTOR 3. If there is an abnormality, replace the power seat adjuster
assembly.

AC003151AB

REA R SEAT ASSEM B LY

REMOVAL AND INSTALLATION
M1522001800071

<VEHICLES WITHOUT PARTIAL <VEHICLES WITH PARTIAL

TRUNK OPENING> TRUNK OPENING>
22 N·m
16 ft-lb 22 N·m 2
2 16 ft-lb

1
1
22 N·m
16 ft-lb

22 N·m
16 ft-lb
22 N·m
16 ft-lb

NOTE
: Hook position
AC003152AB

REMOVAL STEPS
<<A>> 1. REAR SEAT CUSHION
>>A<< 2. REAR SEATBACK

TSB Revision
52A-20 INTERIOR
REAR SEAT ASSEMBLY

REMOVAL SERVICE POINT

<<A>> REAR SEAT CUSHION REMOVAL
While pulling the rear seat stopper pulled, lift up the seat
REAR SEAT STOPPER
cushion to remove it.

AC000341AB

INSTALLATION SERVICE POINT

<<A>> REAR SEATBACK INSTALLATION
Push the seatback in the direction indicated in the illustration;
SEATBACK then securely attach the attachment wire to the body side hook
and install the seatback.

HOOK
ATTACHMENT
WIRE

AC003153AB

DISASSEMBLY AND ASSEMBLY

M1522002000089

<VEHICLES WITHOUT PARTIAL <VEHICLES WITH PARTIAL

TRUNK OPENING> 4 TRUNK OPENING>5

3 N 3
4
8

1 7
6
2

N
1

N
2

N
AC003154AB

TSB Revision
 INTERIOR 52A-21
FRONT SEAT BELT

DISASSEMBLY STEPS DISASSEMBLY STEPS (Continued)

1. REAR SEAT CUSHION COVER 5. LOCK A ASSEMBLY
2. REAR SEAT CUSHION PAD 6. LOCK B ASSEMBLY
3. REAR SEATBACK COVER 7. STOPPER
4. REAR SEATBACK PAD 8. LOCK KNOB

FR O N T SEAT B ELT
REMOVAL AND INSTALLATION
M1523001300079

44 N·m
33 ft-lb 44 N·m
33 ft-lb

4
44 N·m
33 ft-lb

44 N·m
33 ft-lb

AC003155AB

OUTER SEAT BELT REMOVAL INNER SEAT BELT REMOVAL

STEPS STEPS
1. OUTER SEAT BELT • FRONT SEAT ASSEMBLY (REFER
2. REAR PILLAR TRIM (REFER TO TO P.52A-15.)
P.52A-12.) • FRONT SEAT SHIELD COVER
3. ADJUSTABLE SEAT BELT ANCHOR (REFER TO P.52A-16.)
4. INNER SEAT BELT

TSB Revision
52A-22 INTERIOR
FRONT SEAT BELT

INSPECTION
M1523001400076
OUTER SEAT BELT CHECK
VIEW A Check that the B section (red) of the label attached to the outer
seat belt is not exposed from the outer seat belt sleeve. If it is
GOOD BAD
exposed, replace the outer seat belt.
B

SLEEVE
A

SLEEVE AC003156AB

SEAT BELT BUCKLE SWITCH CONTINUITY CHECK

ITEMS TESTER SPECIFIED

TONGUE CONNECTION CONDITION

BUCKLE Fastened seat belt − No continuity

Unfastened seat belt 1 − 2 Continuity

ACX00636 AB

TSB Revision
 INTERIOR 52A-23
REAR SEAT BELT

R EAR SEAT B ELT

REMOVAL AND INSTALLATION
M1523001600070

44 N·m
33 ft-lb

3
44 N·m
33 ft-lb
44 N·m
33 ft-lb
44 N·m
33 ft-lb

1 2
AC003157AB

REMOVAL STEPS REMOVAL STEPS (Continued)

• REAR SEAT (REFER TO P.52A-20.) • REAR SHELF TRIM (REFER TO
1. REAR CENTER SEAT BELT P.52A-12.)
ASSEMBLY (INNER) 3. REAR SEAT BELT ASSEMBLY
2. REAR SEAT BELT ASSEMBLY (OUTER)
(INNER) 4. CENTER REAR SEAT BELT
ASSEMBLY (OUTER)

SPECIFICATIO NS
FASTENER TIGHTENING SPECIFICATIONS
M1521004100078

ITEMS SPECIFICATION
Adjustable seat belt anchor bolt 44 N⋅m (33 ft-lb)
Catch bolt 12 N⋅m (106 in-lb)
Front inner seat belt bolt 44 N⋅m (33 ft-lb)
Front outer seat belt bolt 44 N⋅m (33 ft-lb)
Front seat bolt 44 N⋅m (33 ft-lb)
Front seat nut 29 N⋅m (21 ft-lb)
Front seat reclining adjuster bolt 22 N⋅m (16 ft-lb)
High-mounted stoplight nut 5 N⋅m (44 in-lb)

TSB Revision
52A-24 INTERIOR
SPECIFICATIONS

ITEMS SPECIFICATION
Rear center seat belt bolt 44 N⋅m (33 ft-lb)
Rear inner seat belt bolt 44 N⋅m (33 ft-lb)
Rear outer seat belt bolt 44 N⋅m (33 ft-lb)
Rear center seat belt bolt 44 N⋅m (33 ft-lb)
Rear seatback bolt 22 N⋅m (16 ft-lb)
Tether anchor bolt 22 N⋅m (16 ft-lb)

TSB Revision