BC 22msds

MATERIAL SAFETY DATA SHEET
Star Technology, Inc.

200 Executive Drive Waterloo, IN 46793 260.837.7833-phone 260.837.7834-fax www.star-technology.com Two Part Room Temperature Cure Epoxy
Date Issued: July 24, 2001 Supersedes: February 9, 1996 CHEMTREC (800) 424-9300 or 703-527-3887
I. MATERIAL IDENTIFICATION & PHYSICAL DATA Product Name: BC-22 Part A Product Class: Epoxy Resin
%t Volatile by Vol.: < 1% Boiling Range: N/A Vapor Density: N/A Weight Per Gallon: Approx. 17 lb Vapor Pressure: 1mmHg Evaporation Rate: Nil Solubility in Water: Nil Appearance and Odor: Blue putty with faint epoxy odor II. HAZARDOUS INGREDIENTS CAS # OSHA TWA ppm ACGIA TWA ppm Epoxy Resin 25068-38-6 N/A N/A III. FIRE AND EXPLOSION DATA Flashpoint: >200oF Method: TCC Extinguishing Media: CO2, Dry Powder, Halon, Water Unusual Fire and Explosion Hazards: None Special Fire fighting Procedures: Turn out gear and SCBA equipment IV. REACTIVITY DATA Stability: Stable, if stored properly Hazardous Polymerization: Will not polymerize under normal circumstances Conditions to Avoid: Strong caustics, acids Materials to Avoid: None Hazardous Decomposition Products: Carbon monoxide, Carbon dioxide, water vapor V. HEALTH HAZARD DATA Effects of Overexposure: Ingestion: None Known Skin Absorption: Not Known
MSDS Last printed 5/26/2006 2:32:00 PM BC-22
Skin Contact: Rash and dermatitis effects Eye Contact: Corneal irritation Chronic Effects of Overexposure: Skin rash and reddening accompanied with skin irritation. Emergency & First Aid Data: Eye Contact: Wash eye with water for 15 minutes and seek medical attention. Skin Contact: Wash affected area with soap and water. Ingestion: Do not induce vomiting. Seek medical attention. Inhalation: Because of the viscosity of this product, inhalation of the vapors of such resins are not expected. VI. SPILL AND LEAK PROCEDURES Steps to be taken in case material is released or spilled: Absorb product on sawdust or clay. Waste Disposal Method: Dispose of in accordance with local, state and federal regulations. VII. SPECIAL PROTECTION INFORMATION Respiratory Protection: OSHA approved vapor mask if necessary. Ventilation: Local- Exhaust fumes associated with cure of this product to the out of doors. Mechanical- Adequate Protective Gloves: Neoprene or nitrile Eye Protection: Chemical workers goggles. Other Protective Equipment: Wear rubber apron and elbow length gloves when working with large quantities of this product. VIII. SPECIAL PRECAUTIONS: Like any other chemical, this product should be handled with caution and respect. Check with your supervisor or the manufacturer when questions arise about the proper use and handling of this or any chemical product. IX. TRANSPORTATION INFORMATION D.O.T. Shipping Name: None D.O.T. Hazard Class: None D.O.T. Label(s): None D.O.T. UN/NA Number: None To the best of our knowledge, the information contained herein is accurate. However, Star Technology, Inc. does not assume any liability whatsoever for the accuracy of completeness of the information contained herein. Final determination of suitability of any material is the sole responsibility of the user. All materials may present unknown health hazards and should be used with caution. Although certain hazards are described herein, we cannot guarantee that these are the only hazards that exist.
Page 1 of 2
MATERIAL SAFETY DATA SHEET

Star Technology, Inc.
200 Executive Drive Waterloo, IN 46793 260.837.7833-phone 260.837.7834-fax www.star-technology.com Two Part Room Temperature Cure Epoxy
Date Issued: April 11, 2002 Supersedes: February 9, 1996 CHEMTREC (800) 424-9300 or 703-527-3887
I. MATERIAL IDENTIFICATION & PHYSICAL DATA Product Name: BC-22 Part B Product Class: Epoxy Hardener
% Volatile by Vol: < 1% Boiling Range: N/A Vapor Density: N/A Weight Per Gallon: Approx. 17 lb Vapor Pressure: N/A Evaporation Rate: Nil Solubility in Water: Nil Appearance and Odor: Yellow putty with amine odor II. HAZARDOUS INGREDIENTS CAS # OSHA TWA ppm ACGIA TWA ppm Proprietary Amine Proprietary N/A N/A III. FIRE AND EXPLOSION DATA Flashpoint: >250oF Method: TCC Extinguishing Media: CO2, Dry Powder, Halon, Water Unusual Fire and Explosion Hazards: None Special Fire fighting Procedures: Turn out gear and SCBA equipment IV. REACTIVITY DATA Stability: Stable, if stored properly Hazardous Polymerization: Will not polymerize under normal circumstances Conditions to Avoid: Strong caustics, acids Materials to Avoid: None Hazardous Decomposition Products: Carbon monoxide, Carbon dioxide, water vapor V. HEALTH HAZARD DATA Effects of Overexposure: Ingestion: None Known Skin Absorption: Not Known
MSDS Last printed 5/26/2006 2:32:00 PM BC-22
Skin Contact: Rash and dermatitis effects Eye Contact: Corneal irritation Chronic Effects of Overexposure: Skin rash and reddening accompanied with skin irritation. Emergency & First Aid Data: Eye Contact: Wash with water for 15 minutes and seek medical attention. Skin Contact: Wash affected area with soap and water. Ingestion: Seek medical attention. Do not induce vomiting. Inhalation: Because of the viscosity of this product, inhalation of the vapors of such resins are not expected. VI. SPILL AND LEAK PROCEDURES Steps to be taken in case material is released or spilled: Absorb on sawdust or clay absorbent. Waste Disposal Method: Dispose of in accordance with local, state and federal regulations. VII. SPECIAL PROTECTION INFORMATION Respiratory Protection: OSHA approved vapor mask if necessary. Ventilation: Local- Exhaust fumes associated with cure of this product to the out of doors. Mechanical- Adequate Protective Gloves: Neoprene or nitrile Eye Protection: Chemical workers goggles. Other Protective Equipment: Wear rubber apron and elbow length gloves when working with large quantities of this product. VIII. SPECIAL PRECAUTIONS: Like any other chemical, this product should be handled with caution and respect. Check with your supervisor or the manufacturer when questions arise about the proper use and handling of this or any chemical product. IX. TRANSPORTATION INFORMATION D.O.T. Shipping Name: None D.O.T. Hazard Class: None D.O.T. Label(s): None D.O.T. UN/NA Number: None To the best of our knowledge, the information contained herein is accurate. However, Star Technology, Inc. does not assume any liability whatsoever for the accuracy of completeness of the information contained herein. Final determination of suitability of any material is the sole responsibility of the user. All materials may present unknown health hazards and should be used with caution. Although certain hazards are described h erein, we cannot guarantee that these are the only hazards that exist.
Page 2 of 2

BC 22msds

Uploaded by

Copyright:

Available Formats

BC 22msds

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

BC 22msds

Uploaded by

Copyright:

Available Formats

MATERIAL SAFETY DATA SHEET

Star Technology, Inc.

MATERIAL SAFETY DATA SHEET

You might also like