Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 5 views

    04 - Front Hub Unit Bearing

    Uploaded by

    Henry Silva
    APBHYMA MANUALES manuales.apbhyma@gmail.com

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    04 - Front Hub Unit Bearing

    Uploaded by

    Henry Silva
    5 views2 pages
    APBHYMA MANUALES manuales.apbhyma@gmail.com

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    APBHYMA MANUALES manuales.apbhyma@gmail.com

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    5 views2 pages

    04 - Front Hub Unit Bearing

    Uploaded by

    Henry Silva
    APBHYMA MANUALES manuales.apbhyma@gmail.com

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    You are on page 1of 2

    Front Hub Unit Bearing

    DRIVE SHAFT SYSTEM

    4. Front Hub Unit Bearing CAUTION:


    • Do not get closer the tool which charged
    A: REMOVAL magnetism to magnetic encorder.
    1) Disconnect the ground cable from battery. • Be careful not to damage the magnetic en-
    2) Lift-up the vehicle and remove the front wheels. coder.
    3) Unlock the axle nut.
    (2)

    (1)

    DS-00250
    DS-00038

    4) Remove the axle nut using a socket wrench (1) Magnetic encoder
    while depressing the brake pedal. (2) Front hub unit bearing

    CAUTION: 8) Remove the front hub unit bearing. If it is hard to


    Remove the wheel before loosening the axle remove, use STs.
    nut. Failure to follow this rule may damage the ST1 926470000 AXLE SHAFT PULLER
    wheel bearings. ST2 927140000 AXLE SHAFT PULLER
    5) Remove the disc brake caliper from housing, PLATE
    and suspend it from strut using a wire.
    6) Remove the disc rotor from hub.
    NOTE:
    If the disc rotor seizes up within hub, drive disc rotor
    out by installing an 8-mm bolt in screw hole on ro-
    tor. ST1

    ST2

    DS-00145

    B: INSTALLATION
    1) Place the disc cover between housing and front
    hub unit, and tighten the four bolts.
    Tightening torque:
    DS-00041
    65 N⋅m (6.6 kgf-m, 47.9 ft-lb)
    7) Remove four bolts from housing.

    (A)

    (A)

    DS-00231

    DS-00231 (A) Housing

    (A) Housing

    DS-17
    Front Hub Unit Bearing
    DRIVE SHAFT SYSTEM

    2) Install the front drive shaft. <Ref. to DS-22, IN- NOTE:


    STALLATION, Front Drive Shaft.> Since the hub unit bearing can not be disassem-
    3) Tighten the axle nut temporarily. bled, only hub bolts can be removed.
    4) Install the disc rotor on hub.
    5) Install the disc brake caliper on the housing. (1)

    Tightening torque:
    78 N⋅m (8.0 kgf-m, 57.9 ft-lb)
    6) While depressing the brake pedal, tighten a new
    axle nut (olive color) to specified torque and lock it
    securely. ST

    Tightening torque:
    220 N⋅m (22.4 kgf-m, 162 ft-lb)
    DS-00252
    CAUTION:
    • Install the wheel after installation of the axle (1) Front hub unit bearing
    nut. Failure to follow this rule may damage the
    wheel bearing. D: ASSEMBLY
    • Be sure to tighten the axle nut to specified 1) Attach the hub to ST securely.
    torque. Do not overtighten it as this may dam- ST 927080000 HUB STAND
    age wheel bearing.
    7) After tightening the axle nut, lock it securely. (1)

    ST

    DS-00253

    DS-00048 (1) Front hub unit bearing


    8) Install the wheel and tighten the wheel nuts to 2) Using a press, press new hub bolts until their
    specified torque. seating surfaces contact the hub.
    Tightening torque: NOTE:
    90 N⋅m (9.2 kgf-m, 66 ft-lb) Use 12 mm (0.47 in) dia. holes in HUB STAND to
    C: DISASSEMBLY prevent bolts from tilting.
    Using the ST and a hydraulic press, drive hub bolts E: INSPECTION
    out. Refer to “FRONT AXLE” for inspection procedures.
    ST 28399AG000 HUB STAND <Ref. to DS-16, INSPECTION, Front Axle.>
    CAUTION: CAUTION:
    • Be careful not to hammer the hub bolts. This If there is any fault in the bearing, replace hub
    may deform the hub. unit bearing.
    • Do not reuse the hub bolt.

    DS-18

    You might also like