GLR43301 and GLR2701

Setup and programming instructions

for the single channel Gigalink™ receiver
Programming Videos

www.elsema.com
 NOTES

______________________________________________________________
______________________________________________________________
______________________________________________________________
______________________________________________________________
______________________________________________________________
______________________________________________________________
______________________________________________________________
______________________________________________________________
______________________________________________________________
______________________________________________________________
______________________________________________________________
______________________________________________________________
______________________________________________________________
______________________________________________________________
______________________________________________________________
______________________________________________________________

IMPORTANT WARNING AND SAFETY INSTRUCTIONS

All installations and testing must be done only after reading Risk in the goods purchased shall unless otherwise agreed
and understanding all instructions carefully. All wirings should in written pass to the buyer upon delivery of the goods.
be done only by trained technical personnel. Failing to follow Any figures or estimates given for performance of goods
instructions and the safety warnings may result in serious are based upon the company’s experience and is what the
injury and/or damage to property. company obtains on tests. The company will not accept
Elsema Pty Ltd shall not be liable for any injury, damage, liability for failure to comply with the figures or estimates due
cost, expense or any claim whatsoever to any person or to the nature of variable conditions affecting for example Radio
property which may result from improper use or installation Remote Controls.
of this product. Please keep this setup instruction for future reference.

2 For detailed information visit www.elsema.com

GLR43301 and GLR2701
Setup and programming instructions for the single channel Gigalink™ receiver

FEATURES

›› Single channel receiver with relay output

›› Over 4 billion code combinations
›› Wide Supply voltage, 11.0 to 28.0 AC/DC
›› Highly sensitive receiver input stage
›› Crystal controlled for high reliability
›› Can store unlimited number of transmitters
›› Modes include Momentary, Latching, 1-300 second delayed off, pulsing, security latching, on-off and custom
›› E version receiver available with a weatherproof case
›› Optional QM100 bracket available for easy mounting to cases or walls.
›› Relay rated at 8 Amps / 240AC

DESCRIPTION
This Gigalink™ receiver gives you a relay output that can switch currents up to 8 Amps. There is an on board relay
test switch (4th dipswitch) and a LED to indicate when the relay is “On”. The receiver has a power “On” LED to
indicate that the correct supply voltage is connected
The receiver’s micro-controller can store unlimited number of transmitters with a high security level using the
encrypted 32-bit digital code. Included with the receiver is the Gigalink™ programming cable.

TECHNICAL DATA
11.0 - 28 Volts AC/DC.
Supply Voltage
Use Elsema DC or AC power supply, 12PP1000 or 24PP

Frequencies for GLR43301 433.920 (Standard), 433.664, 433.408, 433.152MHz

Frequency for GLR2701 27.195MHz

Relay Output Relay, rated at 8 Amps / 240VAC

Recommended Antenna ANT433 series (433MHz Series) or ANT27 series (27MHz Series)

Compatible Transmitters GLT433 MHz series, GLT27 MHz series

Enter the World of Wireless 3

 PROGRAMMING INSTRUCTIONS
Single Channel Programming
Single channel programming can be achieved by following the steps below:

Step 1: Connect power to the GIGALINK™ receiver. Make sure all switches on the mode
dipswitch are off.

Step 2: Momentarily short the two CC pins on the receiver board. This sets all the channels
to a random code. If there are transmitters previously programmed, they will have to
be re-programmed when CC pins are shorted. Do not do this step if you want to
keep previously programmed transmitters.

Step 3: Connect the transmitter to the receiver by inserting the GIGALINK™ cable into the
transmitters and receivers 2.5-mm Coding socket. (This will activate the programming
mode and is indicated by the red light (LED) on the transmitter that must remain
“on”).

Step 4: Activate one of the selected channels on the transmitter for approximately one
second, LED should blink twice to confirm code programming and then switch “off”.

Step 5: Disconnect GIGALINK™ cable.

Repeat steps 3 to 5 to program another channel transmitter.

If you are programming another transmitter, do not short out the CC pins. Shorting out the CC pins
will delete all previously programmed transmitters.

4 For detailed information visit www.elsema.com

 SPECIAL PROGRAMMING FEATURE FOR GIGALINK™
Forward Programming
GIGALINK™ receivers have an additional programming feature, known as forward programming. This
feature allows the user to program the transmitter code into the GIGALINK™ receivers. This will enable the
transmitters to activate unlimited number of receivers simultaneously.
Forward Programming Steps:

Step 1: Connect power to the receiver and transmitter.

Step 2: Place a jumper across the CC pins of the receiver.
Step 3: Connect the transmitter and receiver using the coding cable.
Step 4: Press the transmitter button for 2 seconds.
Step 5: Remove the coding cable.
Step 6: Remove the jumper from the CC pin.

The receiver is now programmed with the transmitter’s code. Repeat the above steps to program
another receiver.

Enter the World of Wireless 5

 MODE SETTING
The 4-way dipswitch functions as a mode selector for the relay. User should set the receiver mode correctly. See the
following table for different mode setting.

Dipswitch Mode Settings

The output relay will respond in the following manner when receiving the correct signal from a transmitter.
1 2 3 4

“Momentary”: Relay on, only while correct signal is received

“Latching”: Relay alternates at every correct incoming signal

“Delayed Off 1”: Relay on, but delayed off for 1-10 seconds, adjustable by trimpot

“Delayed Off 2”: Relay on, but delayed off for 10-300 seconds, adjustable by trimpot

“Pulsing”: Relay will pulse at 1Hz for 10-300 seconds, adjustable by trimpot

“Security Latching On”: Relay will energize until supply to receiver is momentarily
interrupted

“On-Off”: This mode requires a 2-channel Tx.

Channel 1 will always energize the relay. Channel 2 will always de-energize the relay
You must press both buttons at the same time during programming (channelised code
programming). Pressing one channel only will not get the on/off function.

“On-Off”: This mode requires a 4-channel Tx.

Channel 3 will always energize the relay
Channel 4 will always de-energize the relay

“Test”: Relay is energized, for test purpose only

6 For detailed information visit www.elsema.com

 ACCESSORIES AVAILABLE

UBB Plastic case for “E” version Gigalink™ Coding Cable SUPREG12/24
GLR43301E/ GLR2701E For coding Gigalink Supply and Battery charger. Ideal
transmitters to receivers for charging backup battery and
supplying the receiver.

Suitable Antennas Suitable Power packs QM100

ANT433 series (433MHz Series) or 12PP-1000, 12V DC 1000mA Quick Mount for easy mounting
ANT27 series (27MHz Series) 24PP, 24V DC 500mA. of receivers on walls.

TROUBLESHOOTING
This section contains helpful troubleshooting tips and solutions.

Symptom Solution
Receiver not responding to Try to program the transmitter again, but this time with the battery
transmitter after programming. connected to the transmitter.
Check if GIGALINK™ cable is inserted correctly.

Transmitter activates wrong channel Wrong dipswitch setting while programming the receiver. Use the
on a multi-channel receiver. dipswitch table and program again.
Transmitter has short range. Check receiver antenna connection. If you are using a shielded
coax cable, check that the shield is connected to the negative and
the coaxial core to the antenna terminal.

LED is flashing on the transmitter. Replace battery.

Enter the World of Wireless 7

 CUSTOMER SUPPORT

If your transmitter and receiver are still not operating properly, contact Elsema’s support office at:
Phone: +61 (2) 9609 4668
Fax: +61 (2) 9725 2663
or you can visit our web site at www.elsema.com for the latest updates.

BLDF512

ELSEMA PTY LTD Local Distributor

31 Tarlington Place
Smithfield NSW 2164 Australia
P 02 9609 4668 F 02 9725 2663
W www.elsema.com