CHAPTER 1 : INTRODUCTION TO PHYSICS

NO
1.
2. 3.

TERMS
Physical quantities Base quantities Derived quantities

DEFINITIONS / MEANING
Quantities that can be measured Physical quantities that cannot be defined in terms of other quantities Physical quantity obtained from the combination of base quantities through multiplication or division or both Units that cannot be defined in terms of other units Units which are obtained from the combination of base units through multiplication or division or both The ability ( of a measuring instrument) to measure a quantity with little or no deviation among the measurements The closeness of a measurement to the actual value The ability ( of a measuring instrument ) to detect a small change in the quantity to be measure The difference between the measured value and the actual value Errors in the calibration of instruments or the non-zero reading when the actual reading should be zero Errors due to the mistakes made by the observer when taking measurements either through incorrect positioning of the eye or the instrument Error due to the incorrect positioning of the eye when reading a measurement The non-zero reading when the actual reading should be zero that is the pointer of the instrument does not return to the zero position when it is not being used

FORMULA

4. 5.

Base units Derived units

6.

Consistency

7. 8.

Accuracy Sensitivity

9. 10.

Error Systematic errors

11.

Random error

12. 13.

Parallax error Zero error

CHAPTER 2 : FORCES AND MOTION

TERMS
Vector quantity Scalar quantity Distance Displacement

DEFINITIONS / MEANING
Physical quantities that have both magnitude and direction Physical quantities that have magnitude only The total path length travelled from one location to the other The distance between two locations measured along the shortest path connecting them in a specified direction Rate of change of distance OR Distance travelled per unit time Rate of change of displacement Rate of change of velocity Rate of decrease in velocity The tendency of the object to remain at rest or if moving to continue its motion The quantity of matter in an object Product of mass and velocity In a closed system, the total momentum before collision is equal to the total momentum after collision provided there is no external force A collision in which the objects do not combine after collision A collision in which the objects are combined after collision A single force that represents the combined effect of two or more forces with magnitude and direction Situation in which forces acting on an object produces no net force. The object is stationary or moves with a constant velocity in a straight line Rate of change of momentum Change in momentum The region around the earth which an object experiences a force towards the centre of earth The gravitational force acting on a mass

FORMULA

5. 6. 7. 8. 9. 10. 11. 12.

Speed Velocity Acceleration Deceleration Inertia Mass Momentum Principle of conservation of momentum

v= v= a=

p = mv m1u1 + m2u2 = m1v1 + m2v2

13. 14. 15.

Elastic collision Non-elastic collision Force Unbalanced / net / resultant force Balanced forces / Forces in equilibrium

F = ma

16.

17. 18. 19.

Force / Impulsive force Impulse Gravitational field

F= impulse = mv mu Impulse = Ft

20.

Gravitational field

g = 10 N kg -1

21. 22. 23. 24.

strength Gravitational acceleration Free fall Weight Newton s Second Law of Motion

25.

Resolution of forces

26.

1 Newton

27. 28.

Energy Work done

29.

Power

of 1 kg placed at that point The acceleration of an object due to the pull of the gravitational force The motion in which the object falls due to gravitational force only The gravitational force acting on the object The acceleration produced by a net force on an object is directly proportional to the magnitude of the net force applied and is inversely proportional to the mass of the object The separation of a single force into two perpendicular components called the vertical and the horizontal component Is the force which acts on a body of mass 1 kg and causes the body to accelerate at 1 m s-2 The ability to do work The product of the applied force and the displacement in the direction of the applied force The rate at which work is done OR the amount of work done per second

g = 10 m s-2

W = mg

F= Fx = F cos Fy = F sin F = ma 1 N = 1 kg x 1 ms-2

W = Fs P= P=

30. 31. 32. 33. 34.

1 watt Kinetic energy Gravitational potential energy Density Principle of Conservation of energy

The power generated when 1 J of work is done 1 s The energy of an object due to its motion The energy of an object due to its higher position in the gravitational field Mass per unit volume Energy cannot be created or destroyed. Energy can be transformed from one form to another. The total energy in a closed system is constant The percentage of the energy input that is transformed into useful energy

1W=

 
2

Ek = mv E = mgh =

35.

Efficiency

Ef = Ef =

   

x 100 x 100

36.

Elasticity

The ability of an object to return to its original size / length / shape when the force that is acting on it is removed

37.

Hooke s Law

The extension of a spring is directly proportional to the applied force provided the elastic limit is not exceeded The maximum force which can act on an object before it loses its elasticity Force per unit extension The energy stored in an object when it is stretched or compressed

F=kx

38.

Elastic limit

39. 40.

Force constant / spring constant Elastic potential energy

k= E=

Fx

E = kx2

CHAPTER 3 : FORCES AND PRESSURE

TERMS
Pressure

DEFINITION / MEANING
Magnitude of force acting perpendicularly to a surface per unit area of the surface The pressure exerted on a surface when a force of 1 N acts perpendicularly to an area of 1 m2 The pressure due to the weight of the air acting per unit area on the earth s surface The pressure applied to an enclosed fluid is transmitted uniformly to every part of the liquid The upward force exerted by a fluid when an object is wholly or partially immersed in the liquid For a body wholly or partially immersed in a fluid, the buoyant force is equal to the weight of the fluid it displaces In a moving fluid, where the speed is low, the pressure is high and where the speed is high, the pressure is low P=

FORMULA

2.

1 pascal or 1 N m-2

3.

Atmospheric pressure

4.

Pascal s Principle

 

 

5.

Buoyant force

F= Vg

6.

Archimedes Principle

7.

Bernoulli s Principle

CHAPTER 4 : HEAT
NO
1.

TERMS
Thermal equilibrium

DEFINITION / MEANING
The situation in which two objects are in thermal contact have the same rate of heat transfer and the same temperature. The NET heat flow between the two objects is zero The temperature at which pure ice melts under the standard atmospheric pressure The temperature of steam from pure water that is boiling under standard atmospheric pressure The amount of heat required to increase the temperature of an object by 1 C The amount of heat that must be supplied to an object of mass 1 kg to increase its temperature by 1 C The amount of heat required to change 1kg of a substances from solid to liquid without any change in temperature The amount of heat required to change 1kg of a substance from liquid to gas without any change in temperature For a fixed mass of gas, the pressure of the gas is inversely proportional to its volume when the temperature is kept constant For a fixed mass of gas, the volume of the gas is directly proportional to the absolute temperature of the gas when the pressure is kept constant For a fixed mass of gas, the pressure of the gas is directly proportional to the absolute temperature of the gas when the volume is kept constant The lower temperature in theory in which the pressure and the kinetic energy of gas molecules are zero

FORMULA

2. 3.

Lower fixed point/ ice point Upper fixed point / steam point Heat capacity Specific heat capacity

4. 5.

c=

6.

Specific latent heat of fusion Specific latent heat of vaporisation Boyle s Law

l=

7.

l= P1V1 = P2V2

8.

9.

Charles Law

 

 

10.

Pressure Law

 

 

11.

Absolute zero

CHAPTER 5 : LIGHT
NO
1.

TERMS
Law of reflection

DEFINITION / MEANING
i)The incident ray, the reflected ray and the normal all lie in the same plane ii)The angle of incidence is equal to the angle of reflection The line passing through the vertex, P and the centre, C The centre of the sphere that forms the curved mirror The point on the principal axis where the reflected rays converge that is meet and intersect The point on the principal axis where the reflected rays diverge that is appear to spread out from behind the mirror The image that can be formed / displayed on a screen The image that cannot be formed on a screen The return of light waves when they hit a reflector ( mirror) The bending of light ray at the boundary as it travels from one medium to another of different optical densities The incident ray, the refracted ray and normal all lie in the same plane. The ratio of sin i/ sin r is a constant (Snell s Law ) The value of the constant ( sin i / sin r ) for a light ray passing through a vacuum into a given medium The distance of the real object from the surface of a medium ( eg water, glass) The distance of the virtual image from the surface of the medium ( eg water, glass) The angle of incidence in the denser medium when the angle of refraction in the less dense medium is 90 The condition in which the light ray from a denser medium to a less dense medium is reflected back into the denser medium when the angle of incidence is greater than the critical angle

FORMULA

2. 3. 4.

Principal axis of a curved mirror Centre of curvature, C Focal point, F of a concave mirror Focal point, F of a convex mirror Real image Virtual image Reflection of light Refraction of light

5.

6. 7. 8. 9.

10.

Law of refraction

11.

Refractive index, n

n=

 

12. 13. 14.

Real depth Apparent depth Critical angle, c

n= n= n=


c = sin -1

15.

Total internal reflection

16.

Focal point, F of a lens

17. 18.

Focal length, f Power of lens

A common point on the principal axis where all the rays parallel to the axis converge to it after passing through a convex lens or appear to diverge from it after passing through a concave lens The distance between the focal point and the optical centre The reciprocal of the focal length

f= P= m= m=
 

19.

Linear magnification

The ratio of the image size to the object size OR the ratio of the image distance to object distance

CHAPTER 6 : WAVES
NO
1. Wave

TERMS

DEFINITION / MEANING
A travelling disturbance from a vibrating or oscillating source which carries energy along with it in the direction of the propagation A uniform to- and- fro motion of an object / particle from a vibrating source A wave in which the particles of the medium oscillate in the direction perpendicular to the direction in which the wave moves ( eg water, light, all EM waves) A wave in which the particles of the medium oscillate in the direction parallel to the direction in which the wave moves (eg sound) An imaginary line that joins all identical points on a wave The to-and- fro motion of an object / particle from one particular point The maximum displacement from the mean position of a wave The time taken to complete one oscillation

FORMULA

2. 3.

Vibration / oscillation Transverse wave

4.

Longitudinal wave

5. 6. 7. 8.

Wavefront One complete oscillation Amplitude, a (SI unit: m) Period, T (SI unit: s)

T=

9. 10.

Frequency, f (SI unit: Hz) Wavelength,

The number of complete oscillations made in 1 second The horizontal distance between two successive equivalent points on a wave

f= = v=f

11. 12. 13.

Damping Natural frequency Resonance

14.

Reflection of waves

Energy loss from an oscillating system to the surrounding in the form of heat energy The frequency in which an oscillating system vibrates when no external force is applied The phenomenon in which an oscillating system is driven at its natural frequency by a periodic force. Maximum energy transfer occurs to the system and it oscillates at a large amplitude The phenomenon when all or part of the wave return after they encounter an obstacle known as reflector

15.

Refraction of waves

The phenomenon in which there is a change of direction of propagation due to a change of speed when water waves travel one area to another of different depths

16.

Diffraction of waves

17. 18. 19.

Interference of waves Coherent waves Principle of Superposition

20.

Constructive interference

21.

Destructive interference

22.

Audio waves

23. 24. 25.

Infrasound Ultrasound Electromagnetic spectrum Electromagnetic waves

26.

The phenomena that refers to the spreading out of waves when they move through a gap or round an obstacle The phenomena in which two sets of coherent waves meet / combine Waves which maintain a constant phase difference, amplitude and frequency The combined wave forms of two or more interfering waves is given by the sum of the displacement of the individual wave at each point of the medium The combination / superposition of two coherent waves in which the vertical displacements of the two waves are in the same direction The combination / superposition of two coherent waves in which a positive displacement of a wave meets a negative displacement of another wave and the combined amplitude becomes zero Sound waves generated between 20 Hz and 20 kHz and can be heard by normal human ears Sound with frequency below 20 Hz Sound with frequency above 20 Hz Consists of a group of waves with similar natures and are arranged in increasing frequencies and decreasing wavelengths Waves which consist of a joint electric and magnetic fields which oscillate perpendicular to each other

CHAPTER 7 : ELECTRICITY
TERMS NO
1. 2. Electric current 1 ampere The rate of charge flow in a circuit The electric current that flows through a conductor if 1 coulomb of charge flows through the conductor in 1 second A region in which an electric charge experiences an electric force The work done or the energy that would be required to move 1 C of charge from one point to another in a circuit The work done to move 1 C of charge between two points in 1 J l= A = C s -1 1A=
 

DEFINITION / MEANING

FORMULA

3. 4.

Electric field Potential difference

V= V = JC -1 1V =
 

5.

1 volt

6.

Resistance

7.

Ohm s Law

8. 9.

Series circuit Parallel circuit

10. 11. 12.

Electromotive force (EMF) Internal resistance, r Electrical power

The ratio of potential difference across a conductor to the electric current flowing through the conductor The electric current passing through an ohmic conductor is directly proportional to the potential difference between its end provided that the temperature and other physical properties of the conductor are constant All the components are connected one after another in a single path All the components are connected with their corresponding ends joined together at common points to form separate and parallel paths The work done by a source ( dry cell / battery) in driving a unit charge around a complete circuit The resistance against the moving charge due to the electrolyte in the cell / battery The rate of electrical energy dissipated or transferred

R=

V = lR

E = l(R+r) r=


P=

CHAPTER 8 : ELECTROMAGNETISM
NO
1. 2. 3.

TERMS
Electromagnet Magnetic field Catapult field

DEFINITION / MEANING
A temporary magnet made by winding a coil of insulated wire round a soft iron core A region round a current- carrying conductor in which a magnetic force acts The resultant magnetic field due to the combination of the magnetic field due to the current in the conductor and the external magnetic field The setting up of an electromotive force in a conductor due to a change in the magnetic flux caused by the relative motion of the conductor and a magnetic field. The induced emf will cause induced current to flow The direction of the induced current in such that the change producing it will be opposed The magnitude of the induced current emf is directly proportional to the rate of change of magnetic flux or the rate of cutting of the magnetic flux A current that flows in one direction only in a circuit and the magnitude of the current maybe constant or changes with time A current which flows to and fro in two opposite directions in a circuit and it changes its direction periodically A device which works on the principle of electromagnetic induction which steps up or steps down alternating current voltages

FORMULA

4.

Electromagnetic induction

5. 6.

Lenz s Law Faraday s Law

7.

Direct current

8.

Alternating current

9.

Transformer

=
Ef =
 

x 100

10.

Step-up transformer

11.

Step-down transformer

A transformer where the number of turns in the secondary coil is greater than the number of turns in primary coil, the voltage across the secondary coil is greater than the voltage across the primary coil A transformer where the number of turns in the secondary coil is less than the number of turns in the primary coil, the voltage across the secondary coil is less than the voltage across the primary coil

12.

Ideal transformer

A transformer in which the output power is equal to the input power and there is no energy loss during the process of transforming the voltages The current induced in the soft iron core due to the changing magnetic field produced by the alternating current in the coils A network system of cables which connects all the power stations and substations in the country to the consumers in a closed network to transmit electricity

P out = P in Vs ls = Vp lp

13.

Eddy current

14.

National Grid Network

CHAPTER 9 : ELECTRONIC
NO
1. 2.

TERMS
Thermionic emission Cathode ray

DEFINITION / MEANING
The process of emission of electrons from the surface of a heated metal The stream of electrons which moves from cathode to anode at high speed across a vacuum A material which can conduct electricity better than insulator, but not as well as conductor A process of adding a certain amount of specific impurities called dopants to a semiconductor to increase its conductivity Semiconductor obtained when pentavelant atoms which are doped into instrinsic semiconductor contribute extra electrons. Free electrons become the majority charge carrier and the holes become the minority carrier Semiconductor obtained when trivalent atoms which are doped into the instrinsic semiconductor contribute extra holes. Free electrons become the minority charge carrier and the holes become the majority charge carrier Formed when pieces of n-type and p-type semiconductors are fused together An electronic device made from a p-n junction that allows current to flow in one direction only but blocks it in the opposite direction The connection in which the p-type (anode) of the diode is connected to the positive terminal of a battery and the n-type (cathode) is connected to the negative terminal of the battery The connection in which the p-type (anode) of the diode is connected to the negative terminal of a battery and the n-type (cathode) is connected to the positive terminal of the battery An electrical device that converts alternating current to direct current

FORMULA

3.

Semiconductor

4.

Doping

5.

n-type semiconductor

6.

p-type semiconductor

7. 8.

p-n junction Semiconductor diode

9.

Forward bias

10.

Reverse bias

11.

Rectifier

12.

Half-wave rectification

13.

Full-wave rectification

14.

Transistor

15.

Logic gates

16.

Truth table

A process where only half of every cycle of an alternating current is made to flow in one direction only A process where both halves of every cycle of an alternating current is made to flow in the same direction An electronic device which has three terminals labeled base, collector and emitter, made by coalescing (fusing) the ntype and p-type semiconductors A switching circuit made up of a combination of transistor switches which has one or more inputs but only one output A record of all the possible combinations of inputs and the corresponding outputs for a particular logic circuit

CHAPTER 10 : RADIOACTIVITY
NO
1. 2. 3. 4.

TERMS
Proton number, Z Nucleon number, A Isotopes Radioactivity

DEFINITION / MEANING
The number of protons in the nucleus of an atom The total number of protons and neutrons in the nucleus of an atom Atoms of an element which have the same proton number but different nucleon number The spontaneous disintegration of an unstable nucleus accompanied by the emission of an energetic particle or a photon ( or radioactive emission ) The process in which an unstable nucleus changes into a more stable nucleus by emitting radiation The energy given out by an unstable nucleus in the form of energetic particles or photon The production of changed particles called ions when the energetic particles or photon passes through a medium, it can knock electrons out of the atoms and molecules of the medium The time taken for the number of the undecayed nuclei in the sample to be reduced to half of its original number Unstable nuclei of an element which have the same number of protons but different number of neutrons which decay and give out radioactive emissions 1/12 of the mass of the carbon-12 atom The process of splitting a heavy nucleus into two lighter nuclei which releases enormous amount of energy Self-sustaining reaction in which the products of a reaction can initiate another similar reaction The process of combining two lighter nuclei to form a heavier nucleus which releases enormous amount of energy Mass and energy are not conserved separately and can be exchanged one for the other by using this equation : E = mc2 Where; E = energy released (J), m = mass defect (kg) c = speed of light (3 x 108 ms-1)

FORMULA

5. 6. 7.

Radioactive decay Radiation Ionizing effect

8.

Half-life

9.

Radioisotopes

10. 11.

Atomic mass unit (amu or u) Nuclear fission

12. 13.

Chain reaction Nuclear fusion

14.

Einstein s Principle