Bid Number/बोली मांक ( बड सं या) :

GEM/2024/B/4852343
Dated/ दनांक : 27-05-2024

Bid Document/ बड द तावेज़

Bid Details/ बड ववरण

Bid End Date/Time/ बड बंद होने क तार ख/समय 17-06-2024 17:00:00

Bid Opening Date/Time/ बड खुलने क

17-06-2024 17:30:00
तार ख/समय

Bid Offer Validity (From End Date)/ बड पेशकश

180 (Days)
वैधता (बंद होने क तार ख से)

Ministry/State Name/मं ालय/रा य का नाम Ministry Of Defence

Department Name/ वभाग का नाम Department Of Military Affairs

Organisation Name/संगठन का नाम Indian Navy

Office Name/कायालय का नाम ***********

Total Quantity/कुल मा ा 4

Item Category/मद केटे गर Movable File Storage System (Compactor) (Q3)

Minimum Average Annual Turnover of the

bidder (For 3 Years)/ बडर का यूनतम औसत 2 Lakh (s)
वा षक टनओवर (3 वष का)

OEM Average Turnover (Last 3 Years)/मूल

4 Lakh (s)
उपकरण िनमाता का औसत टनओवर (गत 3 वष का)

Years of Past Experience Required for

same/similar service/उ ह ं/समान सेवाओं के िलए 1 Year (s)
अपे त वगत अनुभव के वष

MSE Exemption for Years Of

Experience/अनुभव के वष से एमएसई छूट/ and Yes
Turnover/टनओवर के िलए एमएसई को छूट ा है

Startup Exemption for Years of Experience

No
and Turnover/ अनुभव के वष से टाटअप छूट

Experience Criteria,Past Performance,Bidder

Turnover,Certificate (Requested in ATC),OEM Annual
Document required from seller/ व े ता से मांगे Turnover
*In case any bidder is seeking exemption from Experience /
गए द तावेज़ Turnover Criteria, the supporting documents to prove his
eligibility for exemption must be uploaded for evaluation by
the buyer

Past Performance/ वगत दशन 50 %

1/9
 Bid Details/ बड ववरण

Bid to RA enabled/ बड से रवस नीलामी स य कया No

Type of Bid/ बड का कार Two Packet Bid

Time allowed for Technical Clarifications

during technical evaluation/तकनीक मू यांकन के 2 Days
दौरान तकनीक प ीकरण हे तु अनुमत समय

Inspection Required (By Empanelled

Inspection Authority / Agencies pre- Yes
registered with GeM)

Inspection to be carried out by Buyers own

Yes
empanelled agency

Type Of Inspection Post Dispatch

Name of the Empanelled Inspection

Board of Officers
Agency/ Authority

Auto CRAC Days 30

Evaluation Method/मू यांकन प ित Total value wise evaluation

EMD Detail/ईएमड ववरण

Required/आव यकता No

ePBG Detail/ईपीबीजी ववरण

Required/आव यकता No

Splitting/ वभाजन

Bid splitting not applied/बोली वभाजन लागू नह ं कया गया.

Reserved for Make In India products

Reserved for Make In India products Yes

Reserved for MSE

Reserved for MSE Yes

1. If the bidder is a Micro or Small Enterprise as per latest definitions under MSME rules, the bidder shall be
exempted from the requirement of "Bidder Turnover" criteria and "Experience Criteria" subject to meeting of
quality and technical specifications. If the bidder is OEM of the offered products, it would be exempted from the
"OEM Average Turnover" criteria also subject to meeting of quality and technical specifications. In case any
bidder is seeking exemption from Turnover / Experience Criteria, the supporting documents to prove his eligibility

2/9
for exemption must be uploaded for evaluation by the buyer.
2. The minimum average annual financial turnover of the bidder during the last three years, ending on 31st
March of the previous financial year, should be as indicated above in the bid document. Documentary evidence in
the form of certified Audited Balance Sheets of relevant periods or a certificate from the Chartered Accountant /
Cost Accountant indicating the turnover details for the relevant period shall be uploaded with the bid. In case the
date of constitution / incorporation of the bidder is less than 3-year-old, the average turnover in respect of the
completed financial years after the date of constitution shall be taken into account for this criteria.
3. Experience Criteria: In respect of the filter applied for experience criteria, the Bidder or its OEM {themselves or
through reseller(s)} should have regularly, manufactured and supplied same or similar Category Products to any
Central / State Govt Organization / PSU / Public Listed Company for number of Financial years as indicated above
in the bid document before the bid opening date. Copies of relevant contracts to be submitted along with bid in
support of having supplied some quantity during each of the Financial year. In case of bunch bids, the category of
primary product having highest value should meet this criterion.
4. OEM Turn Over Criteria: The minimum average annual financial turnover of the OEM of the offered product
during the last three years, ending on 31st March of the previous financial year, should be as indicated in the bid
document. Documentary evidence in the form of certified Audited Balance Sheets of relevant periods or a
certificate from the Chartered Accountant / Cost Accountant indicating the turnover details for the relevant period
shall be uploaded with the bid. In case the date of constitution / incorporation of the OEM is less than 3 year old,
the average turnover in respect of the completed financial years after the date of constitution shall be taken into
account for this criteria.
5. Bid reserved for Make In India products: : Procurement under this bid is reserved for purchase from Class 1
local supplier as defined in public procurement (Preference to Make in India), Order 2017 as amended from time
to time and its subsequent Orders/Notifications issued by concerned Nodal Ministry for specific Goods/Products.
However, eligible micro and small enterprises will be allowed to participate. The minimum local content to
qualify as a class 1 local supplier is denoted in the bid document. All bidders must upload a certificate from the
OEM regarding the percentage of the local content and the details of locations at which the local value addition is
made along with their bid, failing which the bid is liable to be rejected. In case the bid value is more than Rs 10
Crore, the declaration relating to percentage of local content shall be certified by the statutory auditor or cost
auditor, if the OEM is a company and by a practicing cost accountant or a chartered accountant for OEMs other
than companies as per the Public Procurement (preference to Make-in -India) order 2017 dated 04.06.2020 . In
case Buyer has selected Purchase preference to Micro and Small Enterprises clause in the bid, the same will get
precedence over this clause.
6. Procurement under this bid is reserved for purchase from Micro and Small Enterprises whose credentials are
validated online through Udyog Aadhaar for that product category. If the bidder wants to avail the reservation
benefit, the bidder must be the manufacturer of the offered product in case of bid for supply of goods. Traders
are excluded from the purview of Public Procurement Policy for Micro and Small Enterprises. In respect of bid for
Services, the bidder must be the Service provider of the offered Service. Relevant documentary evidence in this
regard shall be uploaded along with the bid in respect of the offered product or service.
7. Past Performance: The Bidder or its OEM {themselves or through re-seller(s)} should have supplied same or
similar Category Products for 50% of bid quantity, in at least one of the last three Financial years before the bid
opening date to any Central / State Govt Organization / PSU / Public Listed Company. Copies of relevant
contracts (proving supply of cumulative order quantity in any one financial year) to be submitted along with bid
in support of quantity supplied in the relevant Financial year. In case of bunch bids, the category related to
primary product having highest bid value should meet this criterion.
8. Inspection of Stores by Nominated Inspection Authority / Agency of buyer or their
authorized representatives

An independent third party Professional Inspection Body can help buyer in mitigating buyer’s risk with pre-
dispatch/post-dispatch inspection in order to ensure that equipment, components, solutions and documentation
conform to contractual requirements. The buyer has a right to inspect goods in reasonable manner and within
reasonable time at any reasonable place as indicated in contract. Inspection Fee/ Charges (as pre-greed between
buyer and Inspection Agency) would be borne by the buyer as per their internal arrangement but may be
recovered from the seller if the consignment failed to conform to contractual specification and got rejected by
the Inspection Officer .If so requested and accepted by the seller , initially seller may pay for inspection
charges as applicable and get the same reimbursed from buyer if consignment accepted by the Inspecting
Officer . For reimbursement seller has to submit proof of payment to Inspection Agency.

Seller/OEM shall send a notice in writing / e-mail to the Inspecting officer / inspection agency specifying the place
of inspection as per contract and the Inspecting officer shall on receipt of such notice notify to the seller the date
and time when the stores would be inspected. The seller shall, at his own expenses, afford to the Inspecting
officer, all reasonable facilities as may be necessary for satisfying himself that the stores are being and or have
been manufactured in accordance with the technical particulars governing the supply. The decision of the
purchaser representative /inspection authority regarding acceptance / rejection of consignment shall be final and
binding on the seller.

3/9
The Seller shall provide, without any extra charge, all materials, tools, labour and assistance of every kind which
the Inspecting officer may demand of him for any test, and examination, other than special or independent test,
which he shall require to be made on the seller's premises and the seller shall bear and pay all costs attendant
thereon.

The seller shall also provide and deliver store / sample from consignment under inspection free of charge at any
such place other than his premises as the Inspecting officer may specify for acceptance tests for which
seller/OEM does not have the facilities or for special/ independent tests.

In the event of rejection of stores or any part thereof by the Inspecting officer basis testing outside owing to lack
of test facility at sellers premises, the seller shall, on demand, pay to the buyer the costs incurred in the
inspection and/or test. Cost of test shall be assessed at the rate charged by the Laboratory to private persons for
similar work.

Inspector shall have the right to put all the stores or materials forming part of the same or any part thereof to
such tests as he may like fit and proper as per QAP/governing specification. The seller shall not be entitled to
object on any ground whatsoever to the method of testing adopted by the Inspecting officer.

Unless otherwise provided for in the contract, the quantity of the stores or materials expended in test will be
borne by seller.

Inspecting officer is the Final Authority to Certify Performance / accept the consignment. The Inspecting
officer’s decision as regards the rejection shall be final and binding on the seller.

The seller shall if so required at his own expense shall mark or permit the Inspecting officer to mark all the
approved stores with a recognised Government or purchaser's mark.

Movable File Storage System (Compactor) ( 4 pieces )

(Minimum 50% Local Content required for qualifying as Class 1 Local Supplier)

Technical Specifications/तकनीक विश याँ

* As per GeM Category Specification/जेम केटे गर विश के अनुसार

Specification Name/ विश का Bid Requirement/ बड के िलए आव यक (Allowed

Specification
नाम Values)/अनुमत मू य

GENERIC Number of Bays 1-Bay, 2-Bay, 3-Bay, 4-Bay, 5-Bay

Type of Drive Push Pull Type, Mechnized Drive Type, Sprocket Chain
Drive Mechanism

Number of Movable Bodies 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 0

(= A) (Double Faced / Dual
Cabinets covering all bays)
(Total number of available
sections = 2 X number of
bays X A)

Number of Shelves in Each 5 Shelves/6 Compartments, 4 Shelves/5

Section / Cabinet Compartments, 3 Shelves/4 Compartments, 2
Shelves/ 3 Compartments, 11 Shelves/ 12
Compartments

Load Carring Capacity of 60 kg, 70 Kg, 80 Kg, 40 Kg, 50 Kg

Each Shelf (Kg)

4/9
 Specification Name/ विश का Bid Requirement/ बड के िलए आव यक (Allowed
Specification
नाम Values)/अनुमत मू य

MATERIAL M S Sheet Thickness of the 0.8 mm thick CRC sheet conforming to Grade D of IS
Cabinet Body (mm) 513/2008 latest, 1.0 mm thick CRC sheet conforming
to Grade D of IS 513/2008 latest, 0.8 mm
Continuously pre-painted galvanised steel sheets with
protective film 40-45 Micron as per IS 14146, 1.0 mm
Continuously pre-painted galvanised steel sheets with
protective film 40-45 Micron as per IS 14146, 2.0 mm
Continuously pre-painted galvanised steel sheets with
protective film 40-45 Micron as per IS 14146, 2.0 mm
thick CRC sheet conforming to Grade D of IS 513/2008
latest

M S Sheet Thickness of the 1.0 mm thick CRC sheet conforming to Grade D of IS

Shelf Pannels (mm) 513/2008 latest, 0.8 mm thick CRC sheet conforming
to Grade D of IS 513/2008 latest, 0.8 mm
Continuously pre-painted galvanised steel sheets with
protective film 40-45 Micron as per IS 14146, 1.0 mm
Continuously pre-painted galvanised steel sheets with
protective film 40-45 Micron as per IS 14146, 1.25
mm Continuously pre-painted galvanised steel sheets
with protective film 40-45 Micron as per IS 14146,
1.25 mm thick CRC sheet conforming to Grade D of IS
513/2008 latest

M S Sheet Thickness of the 0.8 mm Continuously pre-painted galvanised steel

Door Pannels (mm) sheets with protective film 40-45 Micron as per IS
14146, 1.0 mm Continuously pre-painted galvanised
steel sheets with protective film 40-45 Micron as per
IS 14146, 0.8 mm thick CRC sheet conforming to
Grade D of IS 513/2008 latest, 1.0 mm thick CRC
sheet conforming to Grade D of IS 513/2008 latest,
2.0 mm thick CRC sheet conforming to Grade D of IS
513/2008 latest, 2.0 mm Continuously pre-painted
galvanised steel sheets with protective film 40-45
Micron as per IS 14146, N.A

DIMENSION Overall Height of the 1725, 2080, 2200, 2350, 2600, 2750, 2900, 2950,
Cabinet from the ground in 2130, 1875
mm ±10 (mm)

Depth of the Cabinet 315, 375, 450, 457, 560, 610 (millimeter)
±10(mm)

Width of the Cabinet in mm 905, 915, 1050, 1180, 1500 (millimeter)

(± 5 mm) (THIS IS WIDTH
OF EACH SECTION OR EACH
BAY) Overall width of entire
compactor will be this
width multiplied by number
of bays)

WARRANTY Warranty Period IN NUMBER 1, 2, 3, 4, 5 Or higher

OF YEARS

DOORS AND Central Locking System for YES, NO

LOCKING locking entire compactor
unit

5/9
Consignees/Reporting Officer/परे षती/ रपो टग अिधकार and/ तथा Quantity/मा ा

Consignee
S.No./ . Reporting/Officer/ Delivery Days/ डलीवर के
परे षती/ रपो टग Address/पता Quantity/मा ा
सं. दन
अिधकार

1 *********** ***********SOUTH GOA 4 90

Buyer Added Bid Specific Terms and Conditions/ े ता ारा जोड़ गई बड क वशेष शत

1. Generic

OPTION CLAUSE: The Purchaser reserves the right to increase or decrease the quantity to be ordered up
to 25 percent of bid quantity at the time of placement of contract. The purchaser also reserves the right to
increase the ordered quantity by up to 25% of the contracted quantity during the currency of the
contract at the contracted rates. Bidders are bound to accept the orders accordingly.

2. Generic

Actual delivery (and Installation & Commissioning (if covered in scope of supply)) is to be done at
following address

SSO(qtr)
CSO division
Headquarters Goa Naval Area
Vasco Da Gama
Pin- 403802
.

3. Buyer Added Bid Specific ATC

Buyer Added text based ATC clauses

TECHNICAL BID

Firms Re
sl Technical Details
marks
(
Pre bid meeting attended mandatory (HQ Goa Naval Area, Vasco Da Gama, 403802) at 05 Jun
a Y/N
2024, 1100h
)
(
b Site Inspection undertaken by the bidder Y/N
)
(
Concept of work involved w.r.t specification, quality,design,drawing as explained during the pr
c Y/N
e bid meeting and site inspection understood by the firm
)

The pre bid confrence will be held at HQ/ SSO(Estb) at 1100 hrs on-05 Jun 2024 for clarification and same i
s mandatory. Firms not attending pre bid meeting will be technically qisqualified

6/9
 .

4. Generic

Bidder shall submit the following documents along with their bid for Vendor Code Creation:

a. Copy of PAN Card.

b. Copy of GSTIN.

c. Copy of Cancelled Cheque.

d. Copy of EFT Mandate duly certified by Bank.

5. Warranty

Warranty period of the supplied products shall be 3 years from the date of final acceptance of goods or
after completion of installation, commissioning & testing of goods (if included in the scope of supply), at
consignee location. OEM Warranty certificates must be submitted by Successful Bidder at the time of
delivery of Goods. The seller should guarantee the rectification of goods in case of any break down during
the guarantee period. Seller should have well established Installation, Commissioning, Training,
Troubleshooting and Maintenance Service group in INDIA for attending the after sales service. Details of
Service Centres near consignee destinations are to be uploaded along with the bid.

6. Generic

Installation, Commissioning, Testing, Configuration, Training (if any - which ever is applicable as per scope
of supply) is to be carried out by OEM / OEM Certified resource or OEM authorised Reseller.

7. Turnover

OEM Turn Over Criteria: The minimum average annual financial turnover of the OEM of the offered product
during the last three years, ending on 31st March of the previous financial year, should be as indicated in
the bid document. Documentary evidence in the form of certified Audited Balance Sheets of relevant
periods or a certificate from the Chartered Accountant / Cost Accountant indicating the turnover details for
the relevant period shall be uploaded with the bid. In case the date of constitution / incorporation of the
OEM is less than 3 year old, the average turnover in respect of the completed financial years after the
date of constitution shall be taken into account for this criteria. In case of bunch bids, the OEM of
CATEGORY RELATED TO primary product having highest bid value should meet this criterion.

8. Purchase Preference (State)

Procurement under this bid is reserved for purchase from Micro and Small Enterprises from the State of
Bid Inviting Authority whose credentials are validated online through UDYAM Registration /Udyog Aadhaar
(as validated by Government from time to time) for that product category. If the bidder wants to avail the
reservation benefit, the bidder must be the manufacturer of the offered product in case of bid for supply of
goods. Traders are excluded from the purview of Public Procurement Policy for Micro and Small
Enterprises. In respect of bid for Services, the bidder must be the Service provider of the offered Service.
Relevant documentary evidence in this regard shall be uploaded along with the bid in respect of the
offered product or service. Benifits of MSE will be allowed only if seller is validated on-line in GeM profile
as well as validated and approved by Buyer after evaluation of documents submitted.

9. Purchase Preference (Centre)

Procurement under this bid is reserved for purchase from Micro and Small Enterprises whose credentials
are validated online through Udyog Aadhaar/URC for that product/service category. If the bidder wants to
avail the reservation benefit, the bidder must be the manufacturer of the offered product in case of bid for
supply of goods. Traders are excluded from the purview of Public Procurement Policy for Micro and Small
Enterprises. In respect of bid for Services, the bidder must be the Service provider of the offered Service.
Relevant documentary evidence in this regard shall be uploaded along with the bid in respect of the
offered product or service.

10. Scope of Supply

7/9
 Scope of supply (Bid price to include all cost components) : Only supply of Goods

11. Past Project Experience

Proof for Past Experience and Project Experience clause: For fulfilling the experience criteria any
one of the following documents may be considered as valid proof for meeting the experience criteria:a.
Contract copy along with Invoice(s) with self-certification by the bidder that service/supplies against the
invoices have been executed.b. Execution certificate by client with contract value.c. Any other document
in support of contract execution like Third Party Inspection release note, etc.Proof for Past Experience and
Project Experience clause: For fulfilling the experience criteria any one of the following documents may be
considered as valid proof for meeting the experience criteria:a. Contract copy along with Invoice(s) with
self-certification by the bidder that service/supplies against the invoices have been executed.b. Execution
certificate by client with contract value.c. Any other document in support of contract execution like Third
Party Inspection release note, etc.

Disclaimer/अ वीकरण

The additional terms and conditions have been incorporated by the Buyer after approval of the Competent
Authority in Buyer Organization, whereby Buyer organization is solely responsible for the impact of these clauses
on the bidding process, its outcome, and consequences thereof including any eccentricity / restriction arising in
the bidding process due to these ATCs and due to modification of technical specifications and / or terms and
conditions governing the bid. If any clause(s) is / are incorporated by the Buyer regarding following, the bid and
resultant contracts shall be treated as null and void and such bids may be cancelled by GeM at any stage of
bidding process without any notice:-

1. Definition of Class I and Class II suppliers in the bid not in line with the extant Order / Office Memorandum
issued by DPIIT in this regard.
2. Seeking EMD submission from bidder(s), including via Additional Terms & Conditions, in contravention to
exemption provided to such sellers under GeM GTC.
3. Publishing Custom / BOQ bids for items for which regular GeM categories are available without any
Category item bunched with it.
4. Creating BoQ bid for single item.
5. Mentioning specific Brand or Make or Model or Manufacturer or Dealer name.
6. Mandating submission of documents in physical form as a pre-requisite to qualify bidders.
7. Floating / creation of work contracts as Custom Bids in Services.
8. Seeking sample with bid or approval of samples during bid evaluation process. (However, in bids for
attached categories, trials are allowed as per approved procurement policy of the buyer nodal Ministries)
9. Mandating foreign / international certifications even in case of existence of Indian Standards without
specifying equivalent Indian Certification / standards.
10. Seeking experience from specific organization / department / institute only or from foreign / export
experience.
11. Creating bid for items from irrelevant categories.
12. Incorporating any clause against the MSME policy and Preference to Make in India Policy.
13. Reference of conditions published on any external site or reference to external documents/clauses.
14. Asking for any Tender fee / Bid Participation fee / Auction fee in case of Bids / Forward Auction, as the
case may be.

Further, if any seller has any objection/grievance against these additional clauses or otherwise on any aspect of
this bid, they can raise their representation against the same by using the Representation window provided in
the bid details field in Seller dashboard after logging in as a seller within 4 days of bid publication on GeM. Buyer
is duty bound to reply to all such representations and would not be allowed to open bids if he fails to reply to
such representations.

This Bid is also governed by the General Terms and Conditions/ यह बड सामा य शत के अंतगत भी शािसत है

In terms of GeM GTC clause 26 regarding Restrictions on procurement from a bidder of a country which shares a land border with India, any bidder from a country which
shares a land border with India will be eligible to bid in this tender only if the bidder is registered with the Competent Authority. While participating in bid, Bidder has to

8/9
undertake compliance of this and any false declaration and non-compliance of this would be a ground for immediate termination of the contract and further legal action

in accordance with the laws./ जेम क सामा य शत के खंड 26 के संदभ म भारत के साथ भूिम सीमा साझा करने वाले दे श के बडर से खर द
पर ितबंध के संबंध म भारत के साथ भूिम सीमा साझा करने वाले दे श का कोई भी बडर इस िन वदा म बड दे ने के िलए तभी पा होगा
जब वह बड दे ने वाला स म ािधकार के पास पंजीकृ त हो। बड म भाग लेते समय बडर को इसका अनुपालन करना होगा और कोई भी
गलत घोषणा कए जाने व इसका अनुपालन न करने पर अनुबंध को त काल समा करने और कानून के अनुसार आगे क कानूनी कारवाई
का आधार होगा।

---Thank You/ ध यवाद---

9/9