Bang Ma Loi Robot Motoman Yaskawa nx100 Maintenance Manual

150133-1CD
8 Alarm VNC Automation - Dịch vụ Sửa chữa Servo - Máy CNC - Robot Công nghiệp
8.1 Outline of Alarm - Liên hệ Call/zalo: 0915283693 - Website: https://suarobotcongnghiep.com/
8 Alarm
Outline of Alarm
When an alarm of level 0 to 3 (major alarm) occurs, the servo power supply is turned OFF.
Alarm Code Classification
Alarm Code Alarm Level Alarm Reset Method
Level 0 (Major alarm) It is not possible to reset by "RESET"

(Off line alarm: Initial under the ALARM window or the system
diagnosis/ Hardware input signal (Alarm reset). Turn OFF the
0
diagnosis alarm) main power supply and correct the cause
of the alarm. Then turn ON the main
power supply again.
Level 1 to 3 (Major alarm) It is not possible to reset by "RESET"

under the ALARM window or the system
1
input signal (Alarm reset). Turn OFF the
to
main power supply and correct the cause
3
of the alarm. Then turn ON the main
power supply again.
Level 4 to 8 (Minor alarm) After correcting the cause, it is possible to

4
reset by "RESET" under the ALARM
to
window or the system input signal (Alarm
8
reset).
Level 9 (Minor alarm) After correcting the cause for which the
(I/O alarm) system input signal for the system or user
alarm request turns ON, it is possible to
9
reset by "RESET" under the ALARM
window or the system input signal (Alarm
reset).
8-1
RE-CHO-A104
150133-1CD
8 Alarm
8.2 Alarm Display
Alarm Display
Displaying and Releasing Alarm

If an alarm occurs during operation, the manipulator stops immediately and the ALARM
window appears on the programming pendant indicating that the machine was stopped by an
alarm.
DATA EDIT DISPLAY UTILITY
ALARM
Alarm No. ALARM 4100 [1] Sub-data

OVERRUN (ROBOT)
ALARM 4321 [SLURBT]
Alarm OVERLOAD (MOMENT)
ALARM 4315 [SLURBT]
message COLLISION DETECT
OCCUR TIMES: 1
RESET
Main Menu Short Cut
If more than one alarm occurs simultaneously, all the alarms are displayed. Scroll the viewing
area with the cursor key to view the alarm that is not currently displayed on the viewing area.
The following operations are available in the alarm status: window change, mode change,
alarm reset, and emergency stop. If the window is changed to another window during alarm
occurrence, the ALARM window can be shown again by selecting {SYSTEM INFO} under the
main menu and then selecting {ALARM}.
n Releasing Alarms
Alarms are classified by minor and major alarms.
• Minor Alarms
Select "RESET" on the ALARM window to release alarms.
Or, turn ON the specific signal "ALARM RESET" when using an external input signal
(specific input).
• Major Alarms
If a severe alarm such as hardware failure occurs, servo power is automatically shut OFF
and the manipulator stops. Turn OFF the main power supply, remove the cause of the
alarm, and then turn ON the power supply again.
8-2
RE-CHO-A104
150133-1CD
8 Alarm
8.2 Alarm Display
Special Alarm Display

n Sub Data
Sub data such as data for the axis where the alarm occurred, may also be displayed for
some alarms.
• Decimal data
Without signs: 0 to 65535
With signs: -32768 to 32767
• Binary data
The alarm occurrence data becomes “1.”
With 8 bits: 0000_0001
With 16 bits: 00000001_00000001
• Axis data
The axis where the alarm occurred is highlighted.
With robot axis: Robots 1 to 4 [SLURBT]
With base axis: Robots 1 to 4 [ 1 2 3 ]
With station axis: Stations 1 to 12 [ 1 2 3 ]
• XYZ coordinate data

The coordinates where the alarm occurred are highlighted.
[XYZ]
[ X Y Z Tx Ty Tz ]
• 123 data
The data for which the alarm occurred is highlighted.
[123]
• Control group data

The control group where the alarm occurred is highlighted.
[ R1 R2 S1 S2 S3 ]
n Multiple SERVOPACK System

In a system using more than one SERVOPACK, the number of the SERVOPACK where
the alarm occurred is also displayed. The S1 switch of the AXA01 circuit board shows the
SERVOPACK number.
SV#1: SERVOPACK 1 (AXA01 circuit board S1 switch: 0)
8-3
RE-CHO-A104
150133-1CD
8 Alarm
8.2 Alarm Display
n Independent Control Function (Optional)

In the independent control function (multi-task job), the tasks that were being done when
the alarm occurred are also displayed.
TASK#0: Master-task job
TASK#1: Sub-task1 job (SUB1)
8-4
RE-CHO-A104
150133-1CD
8 Alarm
8.3 Alarm Message List
Alarm Message List
Before handling the system control circuit board “JANCD-NIF∗∗−∗” for any remedies,
consult YASKAWA representative. To handle the JANCD-NIF∗∗−∗, personnel must be
appropriately skilled in maintenance mode operation.
JANCD-NIF∗∗−∗ backs up very important file data for the user program with a battery.
Careless operation may delete registered data.
Alarm Message List

Alarm Sub
Message Cause Remedy
Number Code
An error occurred in communications
between boards when the control power
turned ON.
10 • No response was sent from the • Turn the power OFF then back ON.
optional board #1. • Check that the optional board is correctly
20 • No response was sent from the inserted.
optional board #2. • If the error occurs again, contact your
CPU Yaskawa representative.
0020 COMMUNICATION 50 • No response was sent from the • Turn the power OFF then back ON.
ERROR servo board #1. • Check the connections of communications
51 • No response was sent from the cable, terminator terminal, and the station
servo board #2. number settings.
If the error occurs again, contact your
52 • No response was sent from the Yaskawa representative.
servo board #3.
53 • No response was sent from the
servo board #4.
8-5
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
50 An error occurred in • Turn the power OFF then back ON.
communications with the servo • Check the connections of communications
board #1. cable, terminator terminal, and the station
• The communications CPU for the number settings.
servo board #1 detected an error If the error occurs again, contact your
when the control power turned Yaskawa representative.
ON.
51 An error occurred in
communications with the servo
board #2.
• The communications CPU for the
servo board #2 detected an error
when the control power turned
COMMUNICATION ON.
0021
ERROR (SERVO) 52 An error occurred in
board #3.
ON.
53 An error occurred in
board #4.
ON.
The system program file is damaged.
1 • The NCP01 system program is
damaged.
10 • The system program of optional
board #1 is damaged.
20 • The system program of optional
0030 ROM ERROR 50 • The system program of servo Yaskawa representative.
51 • The system program of servo
1 to An error was detected in • Turn the power OFF then back ON.
15 communications with an I/O module • Check the connections of communications
COMMUNICATION
board when the control power cable, terminator terminal, and the station
0060 ERROR
turned ON. number settings.
(I/O MODULE)
Yaskawa representative.
8-6
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
communications with the servo If the error occurs again, contact your
board #1. Yaskawa representative.
• The error was detected during the
check of the CERF
COMMUNICATION communication watchdog data.
0100 ERROR
(AXA#1) 2 An error occurred in
board #1.
check of the number of the CERF
communications.
check of the CERF
0101 ERROR
board #2.
communications.
check of the CERF
0102 ERROR
board #3.
communications.
COMMUNICATION
0103 ERROR
(AXA#4)
check of the CERF
communication watchdog data.
COMMUNICATION
0103 ERROR
(AXA#4)
communications.
8-7
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
The parameter file is damaged.
0 RC parameter
1 RO parameter
2 SV parameter
3 SVM parameter
4 SC parameter
5 SD parameter
6 CIO parameter • Initialize the corresponding parameter file in
MEMORY ERROR
the maintenance mode.
0200 (PARAMETER 7 FD parameter
FILE) 8 AP parameter Yaskawa representative.
9 RS parameter
10 SE parameter
11 SVC parameter
12 AMC parameter
13 SVP parameter
14 MF parameter
15 SVS parameter
0210 MEMORY ERROR 0 The system configuration • Initialize the system.
(SYSTEM information data are damaged. If the error occurs again, contact your
CONFIG-DATA) Yaskawa representative.
0 The management data of job files
are damaged. • Initialize the job files in the maintenance
mode.
1 The job files are damaged.
MEMORY ERROR 2 The management data of position Yaskawa representative.
0220
(JOB MNG DATA) data files are damaged.
3 The memory play file is damaged. • Initialize the memory play file.
0230 MEMORY ERROR 0 The concurrent I/O ladder program • Initialize the concurrent I/O ladder program.
(LADDER PRG is damaged. If the error occurs again, contact your
FILE) Yaskawa representative.
0240 MEMORRY 0 The DeviceNet allocation file1 is • Use the IO module setting screen in the
ERROR damaged. maintenance mode to initialize the
(DEVICENET 1 The DeviceNet allocation file2 is DeviceNet allocation file.
ALLOC FL) damaged. If the error occurs again, contact your
0270 MEMORY ERROR --- The system software version is • Perform "DATA REBUILD" in the
(CF BACKUP inconsistent with the version when maintenance mode.
FILE) the internal storage data is set or • If the error occurs again after execution of
the CompactFlash on the NCP01 "DATA REBUILD", replace the
board is damaged. CompactFlash on the NCP01 board.
0290 MEMORY ERROR --- The network setting file is • Specify network settings again in
(NETWORK damaged. maintenance mode.
SETUP) If the error occurs again, contact your
8-8
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
2 The setting of concurrent I/O Set a correct module for the concurrent I/O
parameter is incorrect. parameter in the maintenance mode.
3 An invalid value is set for the Set a correct value for the segment clock.
segment clock.
4 Inconsistency was detected in axis- Correctly set the axis-related parameters.
related parameters.
5 Inconsistency was detected in Correctly set the sensor parameters.
VERIFY ERROR sensor parameters.
0300 (SYSTEM 6 System configuration data is • Reset the I/O module in maintenance mode.
CONFIG-DATA) inconsistent. If the error occurs again, contact your
The parameter is inconsistent. Yaskawa representative.
7 The set optional functions are Use the functions of the mounted optional
different from those of the mounted board.
optional board.
8 The function designation for the Set the correct module for the concurrent
concurrent I/O parameter is I/O parameter in the maintenance mode.
incorrect.
VERIFY ERROR 0 The CMOS memory capacity is Initialize the system or use a NIF board with
0310 (CMOS MEMORY different from its initial setting. correct CMOS capacity.
SIZE)
1 to The connected I/O module is
15 different from the function of the set
VERIFY ERROR I/O module.
0320 Connect a correct I/O module.
(I/O MODULE) 16 The I/O module connected to the
17 PCI bus is different from the
function of the set I/O module.
VERIFY ERROR 0 Inconsistency was detected in the Correctly set the application setting
0330 (APPLICATION application setting parameters. parameters.
SETTING)
VERIFY ERROR 0 Inconsistency was detected in the Correctly set the sensor function.
0340 (SENSOR sensor parameters.
FUNCTION)
0 The station No. specified by the
DeviceNet allocation file1 is
incorrect (the station No. is out of
the allowable range, or the
specified station board is not the
DeviceNet master).
1 The MAC_ID specified by the
DeviceNet allocation file1 is not
consistent with the MAC_ID of the
specified station board.
2 Inconsistency was detected in the
scan list of the DeviceNet allocation • Use the IO module setting screen in the
VERIFY ERROR file1. maintenance mode to initialize the
0350 (DEVICENET DeviceNet allocation file.
ALLOC FL) 10 The station No. specified by the If the error occurs again, contact your
DeviceNet allocation file2 is Yaskawa representative.
incorrect (the station No. is out of
the allowable range, or the
specified board is not the
DeviceNet master).
11 The MAC_ID specified by the
DeviceNet allocation file2 is not
consistent with the MAC_ID of the
specified station board.
12 Inconsistency was found in the
scan list of the DeviceNet allocation
file2.
8-9
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
VERIFY ERROR 0 The designation in the parameter is Set a correct value for the welding timer
0370 (SPOT POWER different from the connected designation.
SOURCE I/F) welding timer.
1 The segment clock value which is • Set a correct value for the segment clock.
out of allowable range is set. If the error occurs again, contact your
VERIFY ERROR
0390 (SEGMENT 2 The set value of segment clock is • Set a correct value, which is larger than the
CLOCK) insufficient for communication with current value, for the segment clock.
the servo board. Communication If the error occurs again, contact your
cannot be performed with the servo Yaskawa representative.
board
PARAMETER 50 to An error occurred during the • Turn the power OFF then back ON.
0400 TRANSMISSION 53 parameter/file transfer to the servo If the error occurs again, contact your
ERROR board. Yaskawa representative.
An error occurred during startup • Turn the power OFF then back ON.
MODE CHANGE sequence processing with the If the error occurs again, contact your
0410
ERROR servo CPU, and the system did not Yaskawa representative.
startup normally.
0 The DeviceNet allocation file1 • Verify the connection state of the DeviceNet
could not be transmitted to the board specified by the DeviceNet allocation
specified station. file.
DEVICENET
1 The DeviceNet allocation file2 • Use the IO module setting screen in the
0420 ALLOC FL
could not be transmitted to the maintenance mode to initialize the
TRANSMIT ERR
specified station. DeviceNet allocation file.
--- Motion command processing was • Turn the power OFF then back ON.
SEGMENT PROC
0500 not completed within the specified If the error occurs again, contact your
NOT READY
time. Yaskawa representative.
SOFTWARE --- The combination of the main Correct the combination.
0510 VERSION system program and the servo
UNMATCH system program is incorrect.
0 More axes than the set value are • Set the control group in the maintenance
used. mode with the connectable number of axes.
0520 AXIS LIMIT OVER
MEDAR STATUS --- Refer to the instruction manual for Refer to the instruction manual for the
0600
ERROR the MEDAR function. MEDAR function.
MEDAR --- Refer to the instruction manual for Refer to the instruction manual for the
0601 DIAGNOSIS the MEDAR function. MEDAR function.
ERROR
MEDAR VERSION --- Refer to the instruction manual for Refer to the instruction manual for the
0602
MEDAR REVISION --- Refer to the instruction manual for Refer to the instruction manual for the
0603
MEDAR MODE --- Refer to the instruction manual for Refer to the instruction manual for the
0604
CHANGE ERROR the MEDAR function. MEDAR function.
MEDAR --- Refer to the instruction manual for Refer to the instruction manual for the
SCHEDULE the MEDAR function. MEDAR function.
0605
TRANSMIT
ERROR
--- Refer to the instruction manual for Refer to the instruction manual for the
0606 MEDAR ERROR1
the MEDAR function. MEDAR function.
--- Refer to the instruction manual for Refer to the instruction manual for the
0607 MEDAR ERROR2
the MEDAR function. MEDAR function.
MEDAR WELDER --- Refer to the instruction manual for Refer to the instruction manual for the
0608
TYPE MISMATCH the MEDAR function. MEDAR function.
8-10
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
MEDER --- Refer to the instruction manual for Refer to the instruction manual for the
0609 PARAMETER the MEDAR function. MEDAR function.
ERROR
MEDAR STEPPER --- Refer to the instruction manual for Refer to the instruction manual for the
0610 TRANSMIT the MEDAR function. MEDAR function.
ERROR
LADDER --- The ladder could not be initialized Refer to the instruction manual for the
0710 INITIALIZE successfully. MEDAR function.
ERROR
1 An error was found in the relay No. • Use a correct ladder program.
specification. If the error occurs again, contact your
2 An error was found in the register Yaskawa representative.
No. specification.
3 An incorrect instruction was
entered.
4 Output register is used redundantly.
5 Output relay is used redundantly.
6 Unconnected relay exists.
7 The STR instructions are overused.
8 The AND-STR instructions are
overused.
9 A syntax error was found in the
CNT instruction.
10 The head of the block starts with an
instruction other than the STR
instruction.
LADDER 11 The memory capacity is exceeded
0720 PROGRAM due to excessive machine codes.
ERROR 12 The last instruction is not the END
instruction.
13 An error was found in the PART
instruction.
14 An error was found in the GOUT
instruction.
15 The No. of operand is incorrect.
16 The constant value is incorrect.
17 The step capacity exceeds the
memory capacity.
18 The operation instructions are
overused.
CNT instruction or TMR instruction.
JMP-LABEL instructions.
21 The label of JMP destination does
not exist.
FILE BACKUP --- The management area (FAT) of Replace the CompactFlash in NCP01 board.
0800 ERROR (NCP01 CompactFlash in NCP01 board is
CF) damaged.
File The file in the NCP01 CF could not • Perform "DATA REBUILD" in the
FILE LOAD
No. be retrieved correctly. maintenance mode.
0801 ERROR
(NCP01 CF)
8-11
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
Error An error occurred in access to the • Perform "DATA REBUILD" in the
FILE LOAD
code NCP01 CF. maintenance mode.
0802 ERROR
(NCP01 CF)
--- An error occurred during the Upgrade to the same version and rewrite the
0803 FILE ERROR parameter of Manipulator Model parameter.
(mecha.rom) loading.
8-12
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
0 The TOYOPUC board cannot be Verify that the TOYOPUC board is normally
identified installed.
1 An error was found in the input/
output direction data of allocation
configuration.
3 In the output side setting of
allocation configuration data, the
specified R-register start No. for the
TOYOPUC exceeds the R-register
limit.
set number to use the input side R-
register of the TOYOPUC exceeds
the R-register limit.
set number to use the M-register of
concurrent I/O exceeds the M-
register limit.
8 An error was found in the type set
for output direction of allocation
configuration data.
9 An error was found in the type set
for input direction of allocation
configuration data.
10 An error was found in the type
TOYOPUC ALLOC specified for system data of
0810
DEF ERROR allocation configuration data. Verify and modify the allocation configuration
12 An error was found in the specified data for the TOYOPUC.
number of registers which are used
by the system data "CURR.POS.
(PULSE)" of allocation
configuration.
14 An error was found in the specified
by the system data "CURR.POS.
(XYZ)" of allocation configuration.
by the system data "WELDING
INFO." of allocation configuration.
by the system data "TASK INFO."
of allocation configuration.
by the system data "EXECUTE
PROGRAM INFO." of allocation
configuration.
by the system data "INST.
MESSAGE" of allocation
configuration.
8-13
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
by the system data.
30 In the input side setting of allocation
configuration data, the specified R-
register start No. for the TOYOPUC
exceeds the R-register limit.
configuration data, the set number
to use the input side R-register of
the TOYOPUC exceeds the R-
register limit.
configuration data, the set number
to use the M-register of concurrent
I/O exceeds the M-register limit.
TOYOPUC ALLOC Verify and modify the allocation configuration
0810 by the system data "standard time
DEF ERROR data for the TOYOPUC.
setting data" of allocation
configuration.
allocation configuration data, some
of the TOYOPUC’s R-registers are
specified redundantly.
allocation configuration data, some
of the M-registers of concurrent I/O
are specified redundantly.
configuration data, some of the
TOYOPUC’s R-registers are
configuration data, some of the M-
registers of concurrent I/O are
WATCHDOG --- A system operation error occurred. • Turn the power OFF then back ON.
0900 TIMER ERROR If the error occurs again, contact your
(NIF BOARD) Yaskawa representative.
CPU ERROR Vecto An error was detected in the CPU. Replace the NCP01 board.
0910
(NCP01) r No.
CPU ERROR 100 An error was detected in the CPU Replace the corresponding optional board.
0911
(NCP02#1) of the optional board#1.
CPU ERROR 100 An error was detected in the CPU Replace the corresponding optional board.
0912
(NCP02#2) of the optional board#2.
BUS ERROR 1 The JL chip does not operate Replace the NCP01 board.
0920
(NCP01) normally.
0 Power lost is detected • Verify the state of primary power supply.
CPU HANG UP • Verify the CPS power supply.
0930
ERROR (NCP01) If the error occurs again, contact your
CPU ERROR 100 An error was detected in the CPU
0950 Replace the corresponding servo board.
(AXA#1) of servo board #1.
CPU ERROR 100 An error was detected in the CPU Replace the corresponding servo board.
0951
0952
8-14
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
0953
1 An error occurred in the board or
ROM ERROR system software (ROM).
1000 Replace the NCP01 board.
(NCP01) • A checksum error occurred in the
main ROM.
1∗ A checksum error occurred in the • Turn the power OFF then back ON.
board or the EEPROM. If the error occurs again, contact your
(∗: axis No.) Yaskawa representative.
20 The SRDY signal did not turn ON
after the WRITE ENABLE
command was written. (EEPROM
WRITE ENABLE error)
after the WRITE PROTECT
command was written. (EEPROM
WRITE PROTECT error)
ROM ERROR
1001 after the ERASE command was
(AXA01)
written. (EEPROM ERASE error)
after the CLEAR command was
written. (EEPROM CLEAR error)
after data were written. (EEPROM
writing error)
after data were read. (EEPROM
reading error)
26 The written data were rejected at
verification. (EEPROM verify error)
An error was detected at memory check.
0 • The memory for RC parameter file
is damaged.
1 • The memory for RO parameter file
is damaged.
2 • The memory for SV parameter file
is damaged.
3 • The memory for SVM parameter
file is damaged.
4 • The memory for SC parameter file
is damaged. Initialize the appropriate parameter file in the
MEMORY ERROR
maintenance mode, and then load the
1030 (PARAMETER 5 • The memory for SD parameter file appropriate parameter file saved in the
FILE) is damaged. external memory device.
6 • The memory for CIO parameter
file is damaged.
7 • The memory for FD parameter file
is damaged.
8 • The memory for AP parameter file
is damaged.
9 • The memory for RS parameter file
is damaged.
10 • The memory for SE parameter file
is damaged.
8-15
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
11 • The memory for SVC parameter
file is damaged.
12 • The memory for AMC parameter
file is damaged. Initialize the appropriate parameter file in the
MEMORY ERROR maintenance mode, and then load the
13 • The memory for SVP parameter
1030 (PARAMETER appropriate parameter file saved in the
file is damaged.
FILE) external memory device.
14 • The memory for MF parameter file
is damaged.
15 • The memory for SVS parameter
file is damaged.
The file data used by MOTION are damaged.
1 • The home position calibration file
is damaged.
2 • The tool file is damaged.
3 • The user coordinates file is
damaged.
4 • The robot calibration file is
damaged.
5 • The tool calibration file is
damaged.
6 • The weaving amplitude condition
file is damaged.
7 • The home position correction data
file is damaged.
8 • The conveyor calibration file is
damaged.
9 • The arm and tool interference
prevention file is damaged.
20 • The weaving file is damaged.
21 • The Power Source condition data
file is damaged.
MEMORY ERROR Initialize the damaged file in the maintenance
1031 22 • The welding condition auxiliary file
(MOTION1) mode.
is damaged.
23 • The arc start condition file is
damaged.
24 • The arc end condition file is
damaged.
25 • The COMARC condition file is
damaged.
26 • The COMARC data file is
damaged.
27 • The path correction condition file
is damaged.
28 • The painting characteristics file is
damaged.
29 • The painting condition file is
damaged.
30 • The multi-layer index file is
damaged.
31 • The multi-layer condition file is
damaged.
32 • The sensor monitoring condition
file is damaged.
8-16
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
33 • The name position file is
damaged.
34 • The conveyor condition file is
damaged.
35 • The Press characteristics file is
damaged.
36 • The servo float condition file is
damaged.
37 • The spot welding Power Source
condition data file is damaged.
38 • The air-gun condition file is
damaged.
39 • The motor-gun condition file is
damaged.
40 • The gun pressure file is damaged.
41 • The dry-spotting gun pressure file
is damaged.
42 • The anticipation OT# output file is
damaged.
43 • The anticipation OG# output file is
damaged.
44 • The handling condition file is
damaged.
45 • The form cut file is damaged.
46 • The spot (user) I/O allocation file
MEMORY ERROR is damaged. Initialize the damaged file in the maintenance
1031
(MOTION1) 47 • The linear servo float condition file mode.
is damaged.
48 • The macro definition file is
damaged.
49 • The seal amount correction
condition file (spray) is damaged.
50 • The seal amount correction
condition file (undercoating) is
damaged.
51 • The arc monitor file is damaged.
52 • The motor-gun condition auxiliary
file is damaged.
53 • The job registration table is
damaged.
54 • The painting device condition file
is damaged.
55 • The painting system file is
damaged.
56 • The painting condition file is
damaged.
57 • The paint characteristics file is
damaged.
58 • The EVB gun file is damaged.
59 • The paint filling file is damaged.
60 • The welding pulse condition file is
damaged.
61 • The clearance file is damaged.
8-17
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
62 • The linear scale condition file is
damaged.
MEMORY ERROR Initialize the damaged file in the maintenance
1031 63 • The gauging sensor file is
(MOTION1) mode.
damaged.
64 • The conveyor condition auxiliary
file is damaged.
1 An error occurred in the setup • Turn the power OFF then back ON.
processing of the system when the If the error occurs again, contact your
control power turned ON (Setup Yaskawa representative.
error).
The motion instruction did not start
up. (motion instruction setup
incomplete.)
2 An error occurred in the setup
processing of the system when the
control power turned ON
SET-UP
(Processing timeout).
PROCESS
1050 The motion instruction did not start
ERROR
up. (Setup of the servo control
(SYSCON)
circuit board and NCP02 circuit
board incomplete, parameter
setting value error)
3 An error occurred in the setup • Turn the power OFF then back ON.
processing of the system when the • If the error occurs again, replace the Welder
control power turned ON (Setup I/F board.
error). • If the error occurs again, contact your
The motion instruction did not start Yaskawa representative.
up. (Sport welding management
file setup error.)
An error occurred in the setup process of • Turn the power OFF then back ON.
MOTION when the control power turned ON. If the error occurs again, contact your
1 • The servo control section was not Yaskawa representative.
started up.
2 • The position data of when the
power supply had turned OFF
could not be transmitted to the
servo control section.
3 • The servo control section could
not receive the position data of
when the power supply had
turned OFF.
5 • The request to turn ON the PG
SET-UP power supply for the mounted
1051 PROCESS axis could not be sent.
ERROR (MOTION)
6 • The PG power supply for the
mounted axis could not turn ON.
7 • The request to prepare a
feedback pulse could not be sent.
8 • The feedback pulse could not be
prepared.
9 • The request to initialize the
arithmetic section could not be
sent.
10 • The arithmetic section could not
be initialized.
11 • The request to prepare the current
value could not be sent.
8-18
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
1051 SET-UP 12 • The current value could not be • Turn the power OFF then back ON.
PROCESS prepared. If the error occurs again, contact your
ERROR (MOTION) Yaskawa representative.
--- An unknown alarm was detected Contact your Yaskawa representative.
1100 SYSTEM ERROR
because of noise or control error.
--- An error occurred during the • Turn the power OFF then back ON.
SYSTEM ERROR
1101 system control check. If the error occurs again, contact your
(SYSTEM 1)
SYSTEM ERROR
1102 system control check. If the error occurs again, contact your
(SYSTEM 2)
SYSTEM ERROR
1103 system event data control check. If the error occurs again, contact your
(EVENT)
1104 SYSTEM ERROR --- An error occurred during the • Check the I/O signal line connectors and
(CIO) system I/O control check. (I/O cables.
circuit board communications error, • Reset the I/O module in maintenance mode.
C I/O parameter setting value error • Replace the NIF circuit board, I/O contactor
etc.) unit, and/or I/O module.
0 No processing corresponds to the • Turn the power OFF then back ON.
command code sent from MOTION. If the error occurs again, contact your
1 Illegal command data (parameter) Yaskawa representative.
is received from MOTION.
2 An error occurred in the file transfer
sequence at execution of motion
command.
3 The data size for the file transfer
was over housing size at executing
a motion command.
4 An optional function was
commanded to be executed while
another optional function was in
execution.
5 The request to change
standardization time was sent
without permission.
6 The motor instruction
SYSTEM ERROR standardization time is out of the
1105
(SERVO) allowable range.
7 The KP parameter input value is
out of the allowable range.
8 The KP parameter input value for
two degrees of freedom control is
out of the allowable range.
9 No processing corresponds to the
command code sent from MOTION.
10 An uncontrollable axis was
designated.
11 An attempt was made to apply the
brake to the motor while the power
was being supplied.
12 An attempt was made to supply
power to the motor while the brake
was applied to the motor.
14 An error occurred in the encoder
power supply control process.
8-19
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
15 The segment clock was not the • Turn the power OFF then back ON.
specified value. If the error occurs again, contact your
17 An attempt was made to turn ON Yaskawa representative.
the servo while the encoder was
not ready.
18 The request to turn ON the servo
power supply again was sent to an
axis where the servo’s power was
already ON.
30 The linear servo float does not Contact your Yaskawa representative.
support the manipulator type
specified in the RC parameter at
calculation for servo-float-related
parameters.
37 The manipulator (B-axis) passed Correct the job so that the manipulator (B-
the singular point while the linear axis) does not pass the singular point while
servo float was ON. the linear servo float is ON.
40 The axes for which the servo were • Check the wiring to the contactor.
attempted to be turned ON were If the error occurs again, contact your
not connected to the contactor. Yaskawa representative.
43 The servo ON command was • Turn the power OFF then back ON.
executed while the encoder was in If the error occurs again, contact your
alarm status. Yaskawa representative.
47 The alarm number is illegal. • Turn the power OFF then back ON.
60 The axis endless function is set Disable the axis endless function of motor
enabled for motor guns. guns axis.
61 The axis endless function is set Disable the axis endless function for the
SYSTEM ERROR
1105 enabled for the encoder for which encoder.
(SERVO)
this function cannot be used.
The axis endless function cannot
be used for the encoders
manufactured by Tamagawa Seiki
Co., Ltd.
63 An error occurred while the axis • Turn the power OFF then back ON.
endless function was being used. If the error occurs again, contact your
68 The home position detecting Disable either the axis endless function or the
function was used for the axis for home position detection function.
which the axis endless function was
enabled.
69 The servo float function was used Disable the axis endless function, or do not
for the axis for which the axis use the servo float function.
endless function was enabled.
80 An axis number that is not for gun • Turn the power OFF then back ON.
change was specified. If the error occurs again, contact your
81 An axis number that is not for gun Yaskawa representative.
change was specified.
82 The PG power supply of the axis for
gun change is ON.
83 The servo power supply of the axis
for gun change is ON.
90 The gun number allocated to the
specified physical axis is different
from the specified gun condition file
number.
91 The gun pressure file number is
incorrect.
8-20
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
92 The axis specified for gun pressure • Turn the power OFF then back ON.
is not a gun axis. If the error occurs again, contact your
100 The sequence was untimely Yaskawa representative.
executed in the general-purpose
10ms process although it was not
the execution timing.
101 The sequence was untimely
executed in the segment_G
process although it was not the
execution timing.
executed in the dynamics
calculation process although it was
not the execution timing.
executed in the dynamics
compensation process although it
was not the execution timing.
executed in the servo
communications CERF sending
SYSTEM ERROR
1105 process although it was not the
(SERVO)
execution timing.
executed in the servo
communications CERF receiving
execution timing.
executed in the segment_R
execution timing.
executed in the segment_E
execution timing.
executed in the segment_OPT1
execution timing.
execution timing.
execution timing.
120 A general-purpose 10ms process
did not complete within the time set
on the scheduling table.
8-21
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
121 The segment_G process did not • Turn the power OFF then back ON.
complete within the time set on the If the error occurs again, contact your
scheduling table. Yaskawa representative.
122 The general-purpose 4ms process
(Emergency stop detected.)
125 The dynamics calculation process
126 The dynamics compensation
process did not complete within the
time set on the scheduling table.
127 The CERF transmission process
128 The dynamics calculation process
129 The CERF receiving process did
not complete within the time set on
the scheduling table.
SYSTEM ERROR
1105 130 The segment_R process did not
(SERVO)
complete within the time set on the
scheduling table.
131 The segment_E process did not
complete within the time set on the
scheduling table.
132 The segment_OPT1 process did
150 The segment clock in the ROM for
spot welding is different from the
specified value.
151 The averaging time is not an even
number. (times)
152 An attempt to use a function that is
not allowed in the current ROM was
made.
154 An error occurred in real-time data
transmission of SVSPOT Executing
bit sent from MOTION.
16∗ The illegal data are stored in the
averaging buffer. ( ∗: axis No.)
8-22
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
17∗ The sum value in the averaging • Turn the power OFF then back ON.
buffer is incorrect. (∗: axis No.) • If the error occurs again, contact your
18∗ The “empty” status of averaging
buffer is incorrect. (∗: axis No.)
201 The transfer of servo float condition
file was not successfully completed.
202 The transfer of gun condition file
was not successfully completed.
203 The transfer of gun pressure file
was not successfully completed.
204 The transfer of dry-spotting gun
pressure file was not successfully
completed.
205 The transfer of servo hand
characteristics file was not
successfully completed.
206 The transfer of collision detecting
sensitivity setting file was not
207 The tool file transfer was not
208 The transfer of linear servo float
condition file was not successfully
completed.
209 The transfer of gun condition
auxiliary file was not successfully
completed.
SYSTEM ERROR
1105 300 A logical error occurred in the
(SERVO)
parameter for modification of
resolution which was calculated by
the parameter specified by CMOS.
302 A logical error occurred in the
parameter.
500 Inconsistency of FP register.
600 An uncontrolled axis was specified
when the instruction for group
change was executed.
602 The PG power supply of the axis for
group change is ON.
603 The servo power supply of the axis
for group change is ON.
700 An error occurred in motor control
mode switching process.
800 The observer and collision
detection function are set disabled
although the broken belt detection
function is set enabled.
90∗ Vibration was detected in the serial
encoder. (∗: axis No.)
1000 The check item number of SVD
parameter is unmatched.
1001 The check item number of SV
1002 The check item number of SVM
8-23
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
1003 The check item number of SVP • Turn the power OFF then back ON.
parameter is unmatched. If the error occurs again, contact your
1004 The check item number of AMC Yaskawa representative.
1005 The check item number of MFG
1006 The check item number of MFA
1007 The check item number of SVC
1008 The check item number of SVS
200∗ The status setting to base block is
different from that of base block
signal reading from JL056.
(∗: axis No.)
201∗ The status setting to base block is
different from that of base block
signal writing to JL056.
(∗: axis No.)
SYSTEM ERROR 202∗ The status setting to base block is

1105 different from that of base block
(SERVO)
signal reading from micro program.
(∗: axis No.)
203∗ The mechanical brake remains
locked although the base block is
released.
(∗: axis No.)
204∗ The mechanical brake is not locked
although the base block turns ON.
(∗: axis No.)
2100 The operating software is not used
in the targeted board.
2101 The requested function cannot be
performed.
7XXY Internal data error occurred on the Replace the servo control circuit board.
servo control circuit board
XX: Internal data No.
Y: axis No.
32807 An error occurred in the first • Confirm the communication data line and
encoder communications. motor specification.
1200 HIGH --- Temperature sensor in the CPS • Check for temperature rise in the controller,
TEMPERATURE power unit is activated. The and check if in-panel cooling fan is rotating.
internal temperature of the Cycle the power when the power supply is
controller is abnormally increased. cooled off.
0000_ Communications and power supply • Check the noise source and take
0000_ error occurred in the I/O circuit countermeasures to reduce the noise.
0000_ board. (standard I/O of NIF unit) • Reset the I/O module in maintenance mode.
0001 • Replace the NIF circuit board.
COMMUNICATION ****_ Communications and power supply • Check the I/O signal line (NIF-I/O circuit
1204 ERROR (IO ****_ error occurred in the I/O circuit board) connectors and cables.
MODULE) ****_ board. (standard I/O of NIF unit) • Check the connection of the I/O circuit
***0 ∗: 0 is correct. 1 is incorrect. Bit board and the external device.
position of 1 shows the station • Check the noise source and take
number of incorrect I/O circuit countermeasures to reduce the noise.
board. • Reset the I/O module in maintenance mode.
• Replace the NIF circuit board.
8-24
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
1205 CONTROLNET --- A communication error or power • Check the noise source and take
ERROR supply error occurred on the countermeasures to reduce the noise.
CONTROLNET board. • Reset the I/O module in maintenance mode.
• Replace the CONTROLNET board,
1207 BROKEN B_ON --- The brake relay fuse was blown. Replace the NIF circuit board.
RELAY FUSE
(NIF01)
1208 BROKEN S_ON --- The servo-ON relay fuse was Replace the NIF circuit board.
RELAY FUSE blown.
(NIF01)
1209 EXTERNAL WDT 0000_ Defective watchdog timer circuit Replace the NIF circuit board.
BROKEN 00∗∗ that checks the safety circuit
(NIF01) 0000_0001: 1 signal (PLD1) error
0000_0010: 2 signal (PLD1) error
1210 SERIAL 0000_ Checking error of toggle that Replace the NIF circuit board.
COMMUNICATION 00∗∗ switches double checking safety
TOGGLE CHECK circuits in cycle of 1 ms
ERROR (NIF01) 0000_0001: 1 signal (PLD1) error
INPUT ****_ The signal does not have a match
COMPARISON ****_ signal as a result the mutual check
ERROR ****_ of a dual signal.
(NIF) ****_ 0000_0000_0000_0001: Panel
signal emergency stop signal
(PBESP) unmatched error
0000_0000_0000_0010:
Programming pendant emergency
stop signal (PPESP) unmatched
error
0000_0000_0000_0100: External
emergency stop signal (EXESP)
unmatched error
0000_0000_0000_1000: System
CPU error (ERRCPU) unmatched
error
0000_0000_0001_0000: Servo ON
condition signal (SYSRDY)
unmatched error
0000_0000_0010_0000: Safety
plug signal (SAF) unmatched error
1211 0000_0000_0100_0000: Servo ON Check the signal.
signal (SVON) unmatched error
0000_0000_1000_0000: External
servo ON signal (EXSVON)
unmatched error
0000_0001_0000_0000: Unused
0000_0010_0000_0000:
Maintenance signal (MAINTE)
unmatched error
0000_0100_0000_0001: Enable
switch signal (DSW) unmatched
error
0000_1000_0000_0001: Unused
0001_0000_0000_0000: External
enable switch (EXDSW)
unmatched error
0010_0000_0000_0000: Unused
0100_0000_0000_0000: Safety
speed mode selection (SSP)
unmatched error
1000_0000_0000_0000: Full speed
test (FST) unmatched error
8-25
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
1212 PLD MUTUAL 0000_ The input comparison error Check the one of PPESP, PBESP, EXESP,
MONITOR ERROR 00∗∗ occurred. and SAF signals.
1213 MUTUAL WDT 0000_ The input comparison error Check the one of PPESP, PBESP, EXESP,
ERROR 00∗∗ occurred. and SAF signals.
1214 PBESP RELAY 0000_ The emergency stop button PBESP • Confirm that the cable is not short-circuited.
STICKING 00∗∗ of the NX100 front door is melted • Replace if necessary.
and stuck.
1215 PPESP RELAY 0000_ The emergency stop button of • Confirm that the cable is not short-circuited.
STICKING 00∗∗ programming pendant PPESP is • Replace if necessary.
melted and stuck.
1216 EXESP RELAY 0000_ The external emergency stop • Confirm that the cable is not short-circuited.
STICKING 00∗∗ button EXESP is melted and stuck. • Replace if necessary.
1217 S_ON RELAY 0000_ The servo-ON relay is melted and Replace the servo-ON relay.
STICKING 00∗∗ stuck.
1218 B_ON RELAY 0000_ The brake relay is melted and Replace the brake relay.
STICKING 00∗∗ stuck.
1219 ANOTHER PLD 0000_ The watchdog timer checking the • Turn the power OFF then back ON.
EXT WDT ERROR 00∗∗ safety circuit is incorrect. If the error occurs again, replace the NIF unit.
(NIF BOARD)
LAN 1 Incorrect setting of the IP address Set the correct IP address.
COMMUNICATION which is used in the Ethernet
PARAMETER function.
ERROR 2 Incorrect setting of the subnet mask Set the correct subnet mask.
which is used in the Ethernet
function.
3 Incorrect setting of the default Set the correct default gateway.
gateway which is used in the
Ethernet function.
4 Incorrect setting of the host address Set the correct host address.
function.
1220
30 Incorrect setting of the parameter Set the network SNTP in maintenance mode.
which is used for the SNTP of the
Ethernet function.
31 Incorrect setting of the IP address Set the correct network SNTP server address
of the SNTP server which is used in in maintenance mode.
the Ethernet function of the SNTP.
32 Incorrect setting of the host name Set the correct network SNTP server host
of the SNTP server which is used in name in maintenance mode.
the Ethernet function of the SNTP.
33 Incorrect setting of the parameter of Set the network SNTP in maintenance mode.
the DFCP which is used in the
Ethernet function of the SNTP.
8-26
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
1220 LAN 70 Incorrect setting of the host name Set the correct network SNTP server host
COMMUNICATION which is used in the Ethernet name.
PARAMETER function.
ERROR 71 Incorrect setting of the IP address Set the correct DNS server IP address.
of the DNS server which is used in
the Ethernet function of the DNS.
73 Incorrect setting of the parameter of Set the network DNS in maintenance mode.
74 the DHCP which is used in the
Ethernet function of the DNS.
75 Incorrect setting of the domain Set the correct domain.
function.
ETHERNET 1 An error occurred in the device • Turn the power OFF then back ON.
RESET ERROR initialization process of the Ethernet If the error occurs again, contact your
function. Yaskawa representative.
2 An error occurred in the IP address
setting process of the Ethernet
function.
3 An error occurred in the subnet
mask setting process of the
Ethernet function.
4 An error occurred in the default
gateway setting process of the
Ethernet function.
5 An error occurred in the host name
setting process of the Ethernet
function.
6 An error occurred in the MAC
address acquisition process of the
Ethernet function.
20 An error occurred in the Web server
task creating process of the
Ethernet function.
21 An error occurred in the FTP server
1221
Ethernet function.
22 An error occurred in the FTP client
Ethernet function.
30 An error occurred in the semaphore
generation process for access
exclusion of the Ethernet function.
task management ID getting
process of the Ethernet function.
task management ID getting
59 An error occurred in the DHCP
acquisition item setting process of
the Ethernet function.
initialization process of the Ethernet
function.
interface of the Ethernet function.
8-27
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
ETHERNET 62 The data acquisition process from Verify the DHCP server operation and the
RESET ERROR the server did not complete within network status.
regulated time.
63 The data acquired from the server
were found illegal in the DHCP of
64 An error occurred in the subnet
mask acquisition process in the
DHCP of the Ethernet function.
65 An error occurred in the DNS • Verify the DHCP server operation and the
server address acquisition process network status.
in the DHCP of the Ethernet
function.
66 An error occurred in the Ethernet
function DNS domain acquisition
process in the DHCP of the
Ethernet function.
67 An error occurred in the SNTP
server address acquisition process
in the DHCP of the Ethernet
function.
acquisition process in the DHCP of
69 An error occurred in the DHCP • Turn the power OFF then back ON.
Interface structure mapping If the error occurs again, contact your
process of the Ethernet function. Yaskawa representative.
70 An error occurred in the DNS
1221
resolver initialization process of the
Ethernet function.
71 An error occurred in the DNS
resolver setting of the Ethernet • Verify the domain name and the DNS-
function. related settings.
72 The parameter setting error • When the DHCP is used, verify the DHCP
occurred in the DNS resolver server operation and the network status.
setting of the Ethernet function.
73 The mode error occurred in the • Verify the domain name and the DNS-
DNS resolver setting of the related settings.
Ethernet function. • When the DHCP is used, verify the DHCP
server operation and the network status.
80 An error occurred in the basic • Turn the power OFF then back ON.
library initialization process of the If the error occurs again, contact your
Ethernet function. Yaskawa representative.
81 An error occurred in the
initialization process other than
basic library of the Ethernet
function.
acquisition process in the DHCP of
240 An error occurred in the start
process of the Ethernet function
Telnet (for onboard).
241 An error occurred in the start
process of the Ethernet function
Telnet (for expand).
1222 IP ADDRESS SET ---- The IP address acquired by the • Verify the DHCP server operation and the
FAIL(DHCP) DHCP of Ethernet function is network status.
invalid.
8-28
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
1223 PLD MONITOR1 0000_ The watchdog timer circuit which • Replace the NIF circuit board.
ERROR (HIF01) 00∗∗ checks the safety circuit is
damaged.
1224 PLD MONITOR2 0000_ An error occurred in the watchdog • Turn the power OFF then back ON.
ERROR (HIF01) 00∗∗ timer which checks the safety If the error occurs again, replace the NIF unit.
circuit.
1225 PLD MONITOR3 0000_ An error occurred due to the Check the one of PPESP, PBESP, EXESP,
ERROR (HIF01) 00∗∗ occurrence of input comparison and SAF signals.
error.
1300 SERVO CPU --- A synchronization error occurred • Correct the cable connection or replace the
SYNCHRONIZING between CPUs. cable.
ERROR • Erroneous communications • Replace the main CPU board and/or servo
occurred between the main CPU control board.
board and the servo control circuit
board due to:
- Defective board
- Incorrect connection
Erroneous communications occurred • Correct the cable connection or replace the
between main CPU board and servo control cable.
circuit board due to the defective board or • Replace the main CPU board and/or servo
the incorrect connection. control board.
COMMUNICATION 0 Communication status error
1301
ERROR (SERVO) 1 Watchdog timer error
2 JL040 alarm
3 Communication status error
4 Data consistency error
Erroneous communications occurred • Correct the cable connection or replace the
between the contactor unit (for I/Os, cable.
manipulators, and external axes) and servo • Replace the contactor unit and/or servo
control circuit board due to the defective control circuit board.
board or the incorrect connection.
1 No interrupt from servo I/O
communications (JL080) occurred.
(Communication loop back)
2 The servo I/O communications
(JL080) received status is incorrect.
(No interrupt)
COMMUNICATION 4 The servo I/O communications
1302 ERROR (SERVO I/ (JL080) buffer switch status is
O) incorrect.
(Watchdog timer error)
5 The servo I/O communications
(JL080) receiving status is
incorrect.
(Command timeout)
∗∗10 The communications loop back
value of servo I/O communications
(JL080) is incorrect.
(Communication loop back)
(∗∗: station number of the
connected unit)
8-29
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
∗∗11 The received address of JL080 is • Turn the power OFF then back ON after
unmatched with the sent address. cooling the power supply.
(∗∗: station number of the If the error occurs again, contact your
COMMUNICATION connected unit) Yaskawa representative.
1302 ERROR (SERVO I/
O) ∗∗12 The received buffer of JL080 is
incorrect.
(∗∗: station number of the
connected unit)
1303 ARITHMETIC XYYY An error occurred in control • Turn the power OFF then back ON.
ERROR (SERVO) Z arithmetic process or parameter If the error occurs again, contact your
arithmetic process. Yaskawa representative.
The data [X ] indicates the
generation process.
10000: Observer control
20000: High-precision path
control
30000: Dynamics
40000: Disturbance observer
control
The data [ YYY ] indicates the
alarm contents.
The data [ Z] indicates the
physical axis number.
1304 EX-AXIS BOARD --- • The external board is not mounted Mount an external board or correct the
NOT INSTALLED although an external axis is external axis selection parameter.
specified.
• "With external axes" is specified
for the system without external
axes.
1306 AMPLIFIER TYPE Phy- The amplifier type setting is Set the installed amplifier type in the system
MISMATCH sical incorrect. configuration.
axis
bit
1307 ENCODER TYPE Phy- The encoder type (motor model) Set the installed motor type in the system
MISMATCH sical setting is incorrect. configuration.
axis
bit
1308 CONVERTER --- The converter model set in the Set the mounted converter model in system
TYPE system configuration is different configuration.
MISMATCH from that of the one mounted.
1309 HARDWARE --- Converter hardware is incorrect. • Turn the power OFF then back ON.
ERROR If the error occurs again, replace the
(CONVERTER) converter.
1310 CHARGE ERROR --- Charge error is sent from the • Turn the power OFF then back ON.
(CONVERTER) converter. If the error occurs again, replace the
converter.
1311 A/D DETECTION --- A/D detection error is sent from the • Turn the power OFF then back ON.
ERROR converter. If the error occurs again, replace the
(CONVERTER) converter.
1312 ID ERROR --- ID error is sent from the converter. • Turn the power OFF then back ON.
(CONVERTER) If the error occurs again, replace the
converter.
1316 BROKEN PG LINE --- This error occurs in the motor that • Turn the power OFF then back ON.
is not a serial encoder (motor gun If the error occurs again, replace the board,
axis). connection cable and unit.
There might be a failure on the
AXB01 board, the AXI01 board, the
connection cable between them,
and the XIU unit.
8-30
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
1321 BRAKE BOARD --- Brake signal is incorrect. • Check the wiring around the brake circuit
ERROR board.
If the error occurs again, replace the brake
circuit board.
1322 BRAKE BOARD --- The cutout relay for the brake board • Check and replace the cutout relay for the
STICKING main circuit is melted and stuck. brake board main circuit.
1325 COMMUNICATION --- Communication error occurred • Correct the encoder connection.
ERROR between the encoder and the servo • Check for noise.
(ENCODER) control circuit board due to: • Confirm the motor type.
- Misconnection of encoder If the error occurs again, replace the servo
- Noise from external devices control circuit board.
- Incorrect motor type
- Defective servo control circuit
board or encoder
1326 DEFECTIVE --- An error occurred in the encoder • Turn the power OFF then back ON.
ENCODER position detecting circuit. If the error occurs again, replace the motor of
ABSOLUTE DATA the corresponding axis.
1327 ENCODER OVER --- The control power supply turned • Stop the manipulator motion and then turn
SPEED ON while the encoder was rotating ON the control power supply to check if the
(at more than 400min-1). error occurs.
- The axis was in free-fall state. If the error occurs, the encoder is defective.
- Defective encoder Replace the motor for the axis.
1328 DEFECTIVE --- Internal parameter error of the • Turn the power OFF then back ON.
SERIAL serial encoder If the error occurs again, replace the motor of
ENCODER • The encoder fault may be the the corresponding axis.
cause.
1329 DEFECTIVE --- No response of encoder reset • Turn the power OFF then back ON.
SERIAL completion at the occurrence of If the error occurs again, replace the motor
ENCODER encoder backup error. (encoder) of the corresponding axis.
COMMAND The encoder fault may be the
cause.
1330 MICRO --- Defective servo control circuit • Turn the power OFF then back ON.
PROGRAM board (Occurred only when the If the error occurs again, replace the servo
TRANSMIT control power supply turned ON.) control circuit board.
ERROR
1331 CONVERTER --- Charge error is sent from the • Turn the power OFF then back ON.
CHARGE converter. If the error occurs again, replace the
ERR(CONVERTE converter.
R)
1332 POSITION ERROR --- The number of pulses generated by • Check for the external noise.
one motor rotation does not agree • Provide noise protection such as installing a
with the specified value due to: ferrite core if required.
- Noise from external devices If the error occurs again, replace the servo
- Defective board control circuit board, external axis servo
- Motor failure control circuit board, and/or motor.
1333 POSITION ERROR --- The number of pulses generated by • Check for the external noise.
(SERIAL one motor rotation does not agree • Provide noise protection such as installing a
ENCODER) with the specified value due to: ferrite core if required.
- Noise from external devices If the error occurs again, replace the servo
- Defective board control circuit board, external servo control
- Motor failure circuit board, and/or motor.
1335 INCOMPLETE --- The encoder resetting did not • Connect a battery to the encoder.
ENCODER RESET complete. No battery may be If the error still occurs after having connected
connected. a battery, the encoder fault may be the
cause.
8-31
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
COMMUNICATION No response from the converter.
ERROR
(CONVERTER)
∗01 Communications status error • Turn the power OFF then back ON after
(∗: converter No.) cooling the power supply.
∗02 Command timeout
(∗: converter No.)
∗03 Sent buffer FULL
1343 (∗: converter No.)
∗04 CRC-16 error
∗05 Error code received
∗06 Received command error
1345 SAFETY CIRCUIT XYY Unmatched signal was detected in • Check the wiring of the unmatched signal.
SIGNAL the double-check of the receive • Replace the power-ON unit circuit board.
UNMATCH data to the power-ON unit. • Replace the servo circuit board.
(SERVO)
The data show the No. of power-
ON unit and the unmatched signal.
X···Power-ON unit
0: Power-ON unit1 (TU#1)
YY···Unmatched signal
01: KMMA signal unmatched error
02: SVMAIN signal unmatched error
03: SVMAIN1·2 signal unmatched error
04: IORDY signal unmatched error
05: ONEN signal unmatched error
06: FUCUT signal unmatched error
07: SHOCK1 signal unmatched error
08: EXOT signal unmatched error
09: OT signal unmatched error
10: TUSONER signal unmatched error
11: SVCMPER signal unmatched error
12: TCER signal unmatched error
13: SON_OUT signal unmatched error
14: BRRVER signal unmatched error
60: Error due to unmatched output

signal for servo board failure
61: Error due to unmatched signal
for the main contactor state
(closed contact)
62: Error due to unmatched signal
for the main contactor state
(open contact)
63: Error due to unmatched input
signal for the main contractor
control relay
signal for the OT recovery
signal for the external WDT
8-32
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
1345 SAFETY CIRCUIT XYY 66: Error due to unmatched 1FB • Check the wiring of the unmatched signal.
SIGNAL input signal: the brake release • Replace the power-ON unit circuit board.
UNMATCH control signal • Replace the servo circuit board.
(SERVO)
E.g.)
Sub Code: 208
EXOT signal of the Power-ON unit2
(TU#2) is unmatched.
1349 POWER LOST --- The power to the motor became • Turn the power OFF then back ON.
DETECTION unstable. If the error occurs again, contact your
1350 CONTACTOR --- The mounted board type is Check the board type and replace if
UNIT TYPE unmatched. The safety settings necessary.
UNMATCH have been set for a controller that
does not meet the specifications
outlined in the safety standards.
1352 SERIAL --- An error was detected in bit shifting • Turn the power OFF then back ON.
CORRECTION compensation. If the error occurs again, contact your
FAILED Yaskawa representative.
1355 SERIAL ENC --- Encoder multi-turn limit quantity • Turn the power OFF then back ON.
MULTITURN LIMIT error If the error occurs again, replace the motor
ERR (encode) for axis.
1356 INVALID AXIS --- A task request was sent to an axis • Turn the power OFF then back ON.
SPECIFICATION of the group that was disabled by If the error occurs again, contact your
ERROR the group separation function. Yaskawa representative.
1357 PRESS ERROR --- The position or speed value Check the job.
exceeded the limit value during
pressuring after gun electrode hit
the welded target. The motion after
gun electrode hits the welded target
is incorrect.
1360 PA NOT --- The prealigner is not mounted Check the prealigner connection.
INSTALLED although use of the prealigner has
been selected.
1500 PLD INTERNAL --- PLD internal mutual monitoring • Turn the power OFF then back ON.
MUTUAL error is sent from the TU circuit If the error occurs again, replace the TU
MONITOR ERROR board. circuit board.
(SERVO I/O)
1501 SVMX RELAY --- SVMX relay sticking is sent from • Turn the power OFF then back ON.
STICKING the TU circuit board. If the error occurs again, replace the TU
(SERVO I/O) circuit board.
1502 TACTOR --- Contactor sticking is sent from the • Turn the power OFF then back ON.
STICKING TU circuit board. If the error occurs again, replace the TU
1503 SAFETY CIRCUIT --- Input comparison error is sent from • Turn the power OFF then back ON.
IN FAULT the TU circuit board. If the error occurs again, replace the TU
(SV I/O) circuit board.
1504 TUSON RELAY --- TUSON relay breakdown is sent • Turn the power OFF then back ON.
STICKING from the TU circuit board. If the error occurs again, replace the TU
1505 B_ON RELAY --- B_ON relay fuse breakdown is sent • Turn the power OFF then back ON.
FUSE from the TU circuit board. If the error occurs again, replace the TU
BREAKDOWN circuit board.
(SERVO I/O)
1506 MAIN TACTOR --- Main contactor relay fuse • Turn the power OFF then back ON.
RELAY FUSE breakdown is sent from the TU If the error occurs again, replace the TU
BREAKDOWN circuit board. circuit board.
(SERVO I/O)
8-33
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
1507 S_ON RELAY --- S_ON relay fuse breakdown is sent • Turn the power OFF then back ON.
FUSE from the TU circuit board. If the error occurs again, replace the TU
BREAKDOWN circuit board.
(SERVO I/O)
1508 MUTUAL WDT --- Mutual WDT error is sent from the • Turn the power OFF then back ON.
ERROR TU circuit board. If the error occurs again, replace the TU
1509 EXTERNAL WDT --- PLD internal mutual monitoring • Turn the power OFF then back ON.
OVER error is sent from the TU circuit If the error occurs again, replace the TU
(SERVO I/O) board. circuit board.
1510 EXTERNAL WDT --- External WDT breakdown is sent • Turn the power OFF then back ON.
BREAKDOWN from the TU circuit board. If the error occurs again, replace the TU
1511 SERIAL --- Serial communication toggle check • Turn the power OFF then back ON.
COMMUNICATION error is sent from the TU circuit If the error occurs again, replace the TU
TOGGLE CHECK board. circuit board.
ERROR
(SERVO I/O)
1512 POWER SUPPLY --- The rotation speed of in-panel • Check if in-panel cooling fan is rotating.
FAN ALARM cooling fan decreased. If the fan is not working, verify its wiring.
(SERVO) Should the error persist, replace the in-panel
cooling fan (CPS power unit).
1513 POWER --- Temperature sensor in the CPS • Check for temperature rise in the controller,
SUPPLY power unit is activated. The and check if in-panel cooling fan is rotating.
OVERHEAT internal temperature of the Cycle the power when the power supply is
(SERVO) controller is abnormally increased. cooled off.
1514 OVERHEAT --- Amplifier overheated. • Turn the power OFF then back ON after
(AMPLIFIER) cooling the amplifier.
1515 SON_OUT RELAY --- SON_OUT relay sticking is sent • Turn the power OFF then back ON.
STICKING from the TU circuit board. If the error occurs again, replace the TU
(SERVO) board.
1516 BRRCER RELAY --- BRRCER relay sticking is sent form • Turn the power OFF then back ON.
STICKING the TU circuit board. If the error occurs again, replace the TU
(SERVO I/O) board.
1530 ABSOLUTE DATA --- Absolute data cannot be received • Turn the power OFF then back ON.
ERROR from the encoder or the received • Correct the encoder connection.
(SERVO2) absolute data is incorrect. • Replace the motor and SERVOPACK.
1531 GATE ARRAY 1 --- Reading error of command input. • Turn the power OFF then back ON.
ERROR • Replace the SERVOPACK.
(SERVO 1)
1532 GATE ARRAY 2 --- Reading error of command input. • Turn the power OFF then back ON.
ERROR • Replace the SERVOPACK.
(SERVO 2)
1533 ABSOLUTE --- The number of pulses per rotation • Turn the power OFF then back ON.
ENCODER of the absolute encoder is incorrect. • Correct the encoder connection.
ERROR (SERVO2) • Check for noise.
• Replace the SERVOPACK.
1534 EARTH FAULT --- A ground fault along the motor • Turn the power OFF then back ON.
(SERVO2) power line, motor error, or • Check if a ground fault or interphase short-
SERVOPACK error is suspected. circuiting has not occurred in the U-, V-, and
W-phases of motor power line.
• Replace the motor and SERVOPACK.
1535 WATCHDOG --- The SERVOPACK watch dog is • Turn the power OFF then back ON.
DETECTOR incorrect. • Replace the SERVOPACK.
ERROR (SERVO2)
8-34
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
1536 CURRENT FB --- Disconnection of motor power line • Turn the power OFF then back ON.
ERROR(U PHASE) or the SERVOPACK U-phase • Check for motor power line.
(SERVO2) current detection circuit error is • Replace the SERVOPACK.
suspected.
1537 CURRENT FB --- Disconnection of motor power line • Turn the power OFF then back ON.
ERROR(V PHASE) or the SERVOPACK V-phase • Check for motor power line.
(SERVO2) current detection circuit error is • Replace the SERVOPACK.
suspected.
1538 INCR ENCODER --- Initial pulse of incremental • Turn the power OFF then back ON.
INIT PULSE ERR encoders is incorrect. • Correct the encoder connection.
(SV2) • Check for noise.
1539 SERVO ON --- The servo on command was input • Turn the power OFF then back ON.
COMMAND when the servo on command
INVALID invalid alarm was output.
1540 VIBRATION --- An abnormal vibration was • Turn the power OFF then back ON.
DETECT detected during motor rotation. • Check the settings for manipulator motion
(SERVO2) condition (influence by external force, load
condition).
1541 FULL CLOSE --- The check sum result of the • Turn the power OFF then back ON.
SERIAL encoder memory is incorrect. • Replace the serial conversion unit.
ENCODER SUM • Replace the SERVOPACK.
CHECK ERROR
(SV2)
1542 FULL CLOSE --- Serial encoder internal parameter • Turn the power OFF then back ON.
SERIAL error occurred. • Replace the serial conversion unit.
ENCODER DATA • Replace the SERVOPACK.
ALARM (SERVO2)
1544 FULL CLOSE --- The linear encoder or the serial • Turn the power OFF then back ON.
SERIAL converter unit is damaged. • Replace the serial conversion unit.
ENCODER SCALE • Replace the linear encoder.
ERROR (SERVO2)
1545 FULL CLOSE --- Full close serial converter unit • Turn the power OFF then back ON.
SERIAL communication error occurred. • Check the wiring around the cable between
CONVERTER the serial conversion unit and
UNIT SERVOPACK.
COMMUNICATION • Check for noise.
ERROR • Review the cable between the serial
conversion unit and SERVOPACK.
• Replace the serial conversion unit.
1546 COMMUNICATION --- An error was found in the • Turn the power OFF then back ON.
SET ERR(ML2) MECHATROLINK communication • Set an appropriate MECHATROLINK
transmission frequency. transmission frequency.
1547 CURRENT FB 100※ The motor current value displayed • Check if a short-circuiting or ground fault
ERROR 200※ on the axis data is incorrect has not occurred in the power cables (U-,
(*: axis). V-, and W-phases) or motor.
1550 PALAMETER --- The SERVOPACK EEPROM data • Turn the power OFF then back ON.
DAMAGED is incorrect. • Replace the SERVOPACK.
(SERVO2)
1551 PRIMARY --- The various detection data of the • Turn the power OFF then back ON.
CIRCUIT DETECT power circuit in the SERVOPACK is • Replace the SERVOPACK.
ERR (SERVO2) incorrect.
1552 PALAMETER --- The parameter setting error or a • Turn the power OFF then back ON.
SETTING ERROR failure of SERVOPACK EEPROM • Correct the parameter settings.
(SERVO2) or peripheral circuit is suspected. • Replace the SERVOPACK.
1553 COMBINATION --- The SERVOPACK and motor • Turn the power OFF then back ON.
SETTEING capacity match or the • Correct the SERVOPACK and motor
ERROR (SERVO2) SERVOPACK board is damaged. capacities.
8-35
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
1554 OVER CURRENT --- A ground fault along the motor • Turn the power OFF then back ON.
(SERVO2) power line, interphase short- • Check if a ground fault has not occurred in
circuiting, motor error, or the U-, V-, and W-phase of motor power
SERVOPACK error is suspected. line, or short circuit has not occurred
between these phases.
• Turn the power off and naturally cool down
the manipulator. If the error does not occur
again after natural cooling, review the
manipulator motion conditions (such as
influence by external force and load
condition) and ambient operating
temperature.
1555 ENCODER BACK- --- The voltage drop of encoder • Turn the power OFF then back ON.
UP ERROR backup battery is suspected. • Check the connection and voltage of the
(SERVO2) encoder backup battery.
• Correct the encoder connection.
1556 ENCODER --- Serial encoder memory error • Turn the power OFF then back ON.
INTERNAL DATA occurred. • Replace the motor and SERVOPACK.
ERROR (SERVO2)
1557 ENCODER --- Serial encoder internal parameter • Turn the power OFF then back ON.
ABSOLUTE error occurred. • Correct the encoder connection.
ERROR (SERVO2) • Replace the motor and SERVOPACK.
1558 ENCODER SPEED --- When the power turned ON, the • Turn the power OFF then back ON.
ERROR (SERVO2) motor speed may have exceeded • Replace the motor and SERVOPACK.
the threshold speed.
1559 COMMUNICATION --- The MECHATROLINK • Turn the power OFF then back ON.
GATE ARRAY communication ASIC error • Replace the SERVOPACK.
ERROR (SERVO2) occurred.
1560 SYSTEM ERROR --- The internal program error occurred • Turn the power OFF then back ON.
(SERVO2) in the SERVOPACK. • Replace the SERVOPACK.
1561 BROKEN PG --- The A-phase or B-phase of encoder • Turn the power OFF then back ON.
LINE(A-, B- is disconnected. • Correct the encoder connection.
PHASE) • Check for noise.
(SERVO2) • Replace the motor and SERVOPACK.
1562 BROKEN PG --- The C-phase of encoder is • Turn the power OFF then back ON.
LINE(C-PHASE) disconnected. • Correct the encoder connection.
(SERVO2) • Check for noise.
1563 ENCODER MULTI- --- A clearance or setup of the • Turn the power OFF then back ON.
RETURN LIMIT absolute encoder multi-turn • Replace the motor and SERVOPACK.
SETTING ERROR quantity could not be performed
(SERVO2) correctly.
1564 COMMUNICATION --- A communication error occurred • Turn the power OFF then back ON.
ERROR between encoder and • Correct the encoder connection.
(ENCODER) SERVOPACK. • Check for noise.
(SERVO2) • Replace the motor and SERVOPACK.
1565 ENCODER --- The encoder parameter error • Turn the power OFF then back ON.
PARAMETER occurred. • Replace the motor and SERVOPACK.
ERROR (SERVO2)
1566 ENCODER ECHO --- Communication with the encoder is • Turn the power OFF then back ON.
BACK ERROR incorrect. • Correct the encoder connection.
(SERVO2) • Check for noise.
• Check for FG.
1567 ENCODER MULTI- --- The multi-turn limit value is different • Turn the power OFF then back ON.
RETURN LIMIT between the encoder and the • Replace the SERVOPACK.
UNMATCH SERVOPACK.
(SERVO2)
8-36
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
1568 NO OPTION --- A COMl error occurred in the • Turn the power OFF then back ON.
(SERVO2) SERVOPACK. • Replace the SERVOPACK.
1571 COMMUNICATION --- WDT data updates is incorrect. • Turn the power OFF then back ON.
WATCH DOG • Replace the SERVOPACK.
ERROR (SERVO2)
1572 COMMUNICATION --- The MECHATROLINK • Turn the power OFF then back ON.
ERROR communication error occurred. • Check the wiring around the
(SERVO2) MECHATROLINK communication cable.
• Take some action against noises from the
MECHATROLINK communication cable.
1573 SERVO PACK --- A failure of the SERVOPACK. • Turn the power OFF then back ON.
FAILURE • Replace the SERVOPACK.
(SERVO2)
1576 COMMAND --- A error occurred in the • Turn the power OFF then back ON.
EXECUTE NOT SERVOPACK. • Replace the SERVOPACK.
READY (SERVO2)
1578 MOTOR LINE --- The motor power line disconnection • Turn the power OFF then back ON.
DISCONNECTION may be the cause. • Check for motor power line.
ALARM (SERVO2) • Replace the motor and SERVOPACK.
1579 MOTOR LINE --- The motor power line disconnected • Turn the power OFF then back ON.
DISCONNECTION may be the cause. • Check for motor power line.
ALARM (SERVO2) • Replace the motor and SERVOPACK.
1582 CURRENT --- The motor power cable is • Turn the power OFF then back ON.
DETECTOR disconnected. Or the current • Check for motor power line.
ERROR (SERVO2) detector of the SERVOPACK error. • Replace the motor and SERVOPACK.
1583 PHASE --- The encoder's A, B, C phase output • Turn the power OFF then back ON.
DETECTION phases are incorrect. • Correct the encoder connection.
ERROR (SERVO2) • Check for noise.
1585 MOTOR LOAD --- The motor load position deviation • Turn the power OFF then back ON.
POSITION ERROR exceeded the limit. • Check the connection of mechanical
(SV2) combination.
1590 MC POWER --- The method of the power supply to • Turn the power OFF then back ON.
SUPPLY WIRING a main circuit is incorrect. • Check the connection of power supply of
ERR AC/DC.
(SV2) • Check the regenerative resistor.
1592 MONITOR PLD --- External WDT failure was detected • Turn the power OFF then back ON.
ERROR 1 in TU. If the error occurs again, replace the TU
1593 MONITOR PLD --- External WDT timeout was detected • Turn the power OFF then back ON.
1594 MONITOR PLD --- Error between WDTs was detected • Turn the power OFF then back ON.
4000 MEMORY ERROR --- An error was detected at memory Initialize the tool file in maintenance mode,
(TOOL FILE) check. and then load the tool file saved in the
• The memory for the tool file is external memory device.
damaged.
4001 MEMORY ERROR --- An error was detected at memory Initialize the user coordinates file in
(USER COORD check. maintenance mode, and then load the user
FILE) • The memory for the user coordinates file saved in the external memory
coordinates file is damaged. device.
4002 MEMORY ERROR --- An error was detected at memory Initialize the servo monitor signal file in
(SV MON check. maintenance mode, and then load the servo
SIGNAL FILE) • The memory for the servo monitor monitor signal file saved in the external
signal file is damaged. memory device.
8-37
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
4003 MEMORY ERROR --- An error was detected at memory Initialize the weaving condition file in
(WEAVING FILE) check. maintenance mode, and then load the
• The memory for the weaving weaving condition file saved in the external
condition file is damaged. memory device.
4004 MEMORY ERROR --- An error was detected at memory • Reset the alarm, and set the home
(HOME POS FILE) check. positioning data (absolute data) again.
• The memory for the home • Load the home positioning file saved in the
positioning file is damaged. external memory device.
4005 MEMORY ERROR --- An error was detected at memory Load the second home position file saved in
(SECOND HOME check. the external memory device.
POS) • The memory for the second home
position file is damaged.
4006 MEMORY ERROR --- An error was detected at memory Initialize the arc welding Power Source
(POWER SOURCE check. condition file in the maintenance mode, and
COND) • The memory for the arc welding then load the arc welding Power Source
Power Source condition file is condition file saved in the external memory
damaged. device.
4007 MEMORY ERROR --- An error was detected at memory Initialize the arc start condition file in the
(ARC START check. maintenance mode, and then load the arc
COND FILE) • The memory for the arc start start condition file saved in the external
4008 MEMORY ERROR --- An error was detected at memory Initialize the arc end condition file in the
(ARC END COND check. maintenance mode, and then load the arc
FILE) • The memory for the arc end end condition file saved in the external
4009 MEMORY ERROR --- An error was detected at memory Initialize the arc auxiliary condition file in the
(ARC AUX COND check. maintenance mode, and then load the arc
FILE) • The memory for the arc auxiliary auxiliary condition file saved in the external
4010 MEMORY ERROR --- An error was detected at memory Initialize the COM-ARC condition file in the
(COM-ARC COND check. maintenance mode, and then load the COM-
FILE) • The memory for the COM-ARC ARC condition file saved in the external
4012 MEMORY ERROR --- An error was detected at memory Initialize the link servo float condition file in
(LINK check. the maintenance mode, and then load the
SERVOFLOAT) • The memory for the link servo link servo float condition file saved in the
float condition file is damaged. external memory device.
4013 MEMORY ERROR --- An error was detected at memory Initialize the linear servo float condition file in
(LINEAR check. the maintenance mode, and then load the
SERVOFLOAT) • The memory for the linear servo linear servo float condition file saved in the
float condition file is damaged. external memory device.
4014 MEMORY ERROR --- An error was detected at memory Initialize the file for calibration between
(ROBOT CARIB check. manipulators in the maintenance mode, and
FILE) • The memory for the file for then load the file for calibration between
calibration between manipulators manipulators saved in the external memory
is damaged. device.
4017 MEMORY ERROR --- An error was detected at memory Initialize the Power Source characteristics
(POWER SRC check. user definition file in the maintenance mode,
USER DEF) • The memory for the Power Source and then load the Power Source
characteristics user definition file characteristics user definition file saved in the
is damaged. external memory device.
4018 MEMORY ERROR --- An error was detected at memory Initialize the ladder program file in the
(LADDER PRG check. maintenance mode, and then load the ladder
FILE) • The memory for the ladder program file saved in the external memory
program file is damaged. device.
4019 MEMORY ERROR --- An error was detected at memory Initialize the user coordinates file in the
(CUTTING COND check. maintenance mode, and then load the user
FILE) • The memory for the user coordinates file saved in the external memory
coordinates file is damaged. device.
8-38
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
4020 MEMORY ERROR --- An error was detected at memory Initialize the work home position file.
(WORK HOME check.
POS FILE) • The memory for the work home
position file is damaged.
4021 MEMORY ERROR --- An error was detected at memory Initialize the conveyor condition file in the
(CONVEYOR check. maintenance mode, and then load the
COND FILE) • The memory for the conveyor conveyor condition file saved in the external
4024 MEMORY ERROR --- The error was detected at the Initialize the wrist weaving amplitude
(WRIST WEAV memory check. interruption job file in maintenance mode,
AMP FILE IS • The wrist weav amp file is and then load the wrist weaving amplitude file
DAMAGED) damaged. saved in the external memory device.
4025 MEMORY ERROR --- An error was detected at memory Initialize the interrupt job file in the
(INTERRUPT JOB check. maintenance mode, and then load the
FILE) • The memory for the interrupt job interrupt job file saved in the external
file is damaged. memory device.
4028 MEMORY ERROR --- An error was detected at memory Initialize the sensor monitoring condition file
(SENSOR MON check. in the maintenance mode, and then load the
COND FILE) • The memory for the sensor sensor monitoring condition file saved in the
monitoring condition file is external memory device.
damaged.
4031 MEMORY ERROR --- An error was detected at memory Initialize the spot welding gun condition file in
(GUN COND FILE) check. the maintenance mode, and then load the
• The memory for the spot welding spot welding gun condition file saved in the
gun condition file is damaged. external memory device.
4032 MEMORY ERROR --- An error was detected at memory Initialize the spot welding SPOT WELD
(SPOT WELD check. condition file in the maintenance mode, and
COND) • The memory for the spot welding then load the spot welding Power Source
Power Source condition file is condition file saved in the external memory
damaged. device.
4033 MEMORY ERROR --- An error was detected at memory Initialize the gun pressure file in the
(GUN PRESSURE check. maintenance mode, and then load the gun
FILE) • The memory for the gun pressure pressure file saved in the external memory
file is damaged. device.
4034 MEMORY ERROR --- An error was detected at memory Initialize the anticipation outputs file in the
(ANTICIPATION check. maintenance mode, and then load the
OT FILE) • The memory for the anticipation anticipation outputs file saved in the external
outputs (OT) file is damaged. memory device.
4035 MEMORY ERROR --- An error was detected at memory Initialize the anticipation outputs file in the
(ANTICIPATION check. maintenance mode, and then load the
OG FILE) • The memory for the anticipation anticipation outputs file saved in the external
outputs (OG) file is damaged. memory device.
4036 MEMORY ERROR --- An error was detected at memory Initialize the wear amount file in the
(WEARING FILE) check. maintenance mode, and then load the wear
• The memory for the wear amount amount file saved in the external memory
4037 MEMORY ERROR --- An error was detected at memory Initialize the FULL/SHORT OPEN position
(STROKE check. setting file in the maintenance mode, and
POSITION) • The memory for the FULL/SHORT then load the FULL/SHORT OPEN position
OPEN position setting file is setting file saved in the external memory
damaged. device.
4038 MEMORY ERROR --- An error was detected at memory Initialize the dry-spotting pressure file in the
(PRESSURE FILE) check. maintenance mode, and then load the dry-
• The memory for the dry-spotting spotting pressure file saved in the external
pressure file is damaged. memory device.
4039 MEMORY ERROR --- An error was detected at memory Initialize the form cut file in the maintenance
(FORM CUT FILE) check. mode, and then load the form cut file saved in
• The memory for the form cut file is the external memory device.
damaged.
8-39
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
4040 MEMORY ERROR --- An error was detected at memory Initialize the shock level file in the
(SHOCK LEVEL check. maintenance mode, and then load the shock
FILE) • The memory for the shock level level file saved in the external memory
4041 MEMORY ERROR --- An error was detected at memory Initialize the spot I/O allocation file in the
(SPOT IO check. maintenance mode, and then load the spot
ALLOCATE FL) • The memory for the spot I/O I/O allocation file saved in the external
allocation file is damaged. memory device.
4042 MEMORY ERROR --- An error was detected at memory Initialize the vision condition file in the
(VISION FILE) check. maintenance mode, and then load the vision
• The memory for the vision condition file saved in the external memory
condition file is damaged. device.
4043 MEMORY ERROR --- An error was detected at memory Initialize the vision calibration file in the
(VISION check. maintenance mode, and then load the vision
CALIBRATION) • The memory for the vision calibration file saved in the external memory
calibration file is damaged. device.
4044 MEMORY ERROR --- An error was detected at memory Initialize the welding pulse condition file in the
(WELDING PULSE check. maintenance mode, and then load the
COND FILE) • The memory for the welding pulse welding pulse condition file saved in the
condition file is damaged. external memory device.
4045 MEMORY ERROR --- An error was detected at memory Initialize the welding pulse selection file in the
(WELDING PULSE check. maintenance mode, and then load the
SELECTION FILE) • The memory for the welding pulse welding pulse selection file saved in the
selection file is damaged. external memory device.
4046 MEMORY ERROR --- An error was detected at memory Initialize the conveyor calibration file in the
(CONVEYOR check. maintenance mode, and then load the
CALIBRATION) • The memory for the conveyor conveyor calibration file saved in the external
calibration file is damaged. memory device.
4047 MEMORY ERROR --- An error was detected at memory Initialize the macro definition file in the
(MACRO check. maintenance mode, and then load the macro
DEFINITION FILE) • The memory for the macro definition file saved in the external memory
definition file is damaged. device.
4048 MEMORY ERROR --- An error was detected at memory Initialize the sealer gun characteristics file in
(SERVO S-GUN check. the maintenance mode, and then load the
FILE) • The memory for the sealer gun sealer gun characteristics file saved in the
characteristics file is damaged. external memory device.
4049 MEMORY ERROR --- An error was detected at memory Initialize the painting amount correction file in
(PASTE QUAN check. the maintenance mode, and then load the
COMPENSATION • The memory for the painting painting amount correction file saved in the
FILE) amount correction file is external memory device.
damaged.
4050 MEMORY ERROR --- An error was detected at memory Initialize the axis motion I/O allocation file in
(AXIS I/O check. the maintenance mode, and then load the
ALLOCATION • The memory for the axis motion I/ axis motion I/O allocation file saved in the
FILE) O allocation file is damaged. external memory device.
4051 MEMORY ERROR --- An error was detected at memory Initialize the gun characteristics auxiliary file
(GUN COND AUX check. in the maintenance mode, and then load the
FILE) • The memory for the gun gun characteristics auxiliary file saved in the
characteristics auxiliary file is external memory device.
damaged.
4052 MEMORY ERROR --- An error was detected at memory Initialize the tool interference file in the
(TOOL check. maintenance mode, and then load the tool
INTERFERENCE • The memory for the tool interference file saved in the external
FILE) interference file is damaged. memory device.
4053 MEMORY ERROR --- An error was detected at memory Initialize the painting system setting file in the
(PAINTING check. maintenance mode, and then load the
SYSTEM • The memory for the painting painting system setting file saved in the
CONFIGURATION) system setting file is damaged. external memory device.
8-40
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
4054 MEMORY ERROR --- An error was detected at memory Initialize the painting device characteristics
(PAINTING check. file in the maintenance mode, and then load
SPECIAL) • The memory for the painting the painting device characteristics file saved
device characteristics file is in the external memory device.
damaged.
4055 MEMORY ERROR --- An error was detected at memory Initialize the painting CCV file in the
(CCV-PAINT check. maintenance mode, and then load the
TABLE) • The memory for the painting CCV painting CCV file saved in the external
file is damaged. memory device.
4056 MEMORY ERROR --- An error was detected at memory Initialize the paint filling file in the
(PLUG VOLUME check. maintenance mode, and then load the paint
FILE) • The memory for the paint filling file filling file saved in the external memory
is damaged. device.
4057 MEMORY ERROR --- An error was detected at memory Initialize the EVB gun file in the maintenance
(EVB GUN COND) check. mode, and then load the EVB gun file saved
• The memory for the EVB gun file in the external memory device.
is damaged.
4058 MEMORY ERROR --- An error was detected at memory Initialize the EVB turbine file in the
(EVB TURBINE check. maintenance mode, and then load the EVB
COND) • The memory for the EVB turbine turbine file saved in the external memory
4059 MEMORY ERROR --- An error was detected at memory Initialize the EVB paint file in the
(EVB PAINT check. maintenance mode, and then load the EVB
COND) • The memory for the EVB paint file paint file saved in the external memory
is damaged. device.
4060 MEMORY ERROR --- An error was detected at memory Initialize the clearance file in the maintenance
(CLEARANCE check. mode, and then load the clearance file saved
FILE) • The memory for the clearance file in the external memory device.
is damaged.
4061 MEMORY ERROR --- An error was detected at memory Initialize the gaging sensor file in the
(GAGING check. maintenance mode, and then load the gaging
SENSOR FILE) • The memory for the gaging sensor sensor file saved in the external memory
4062 MEMORY ERROR --- An error was detected at memory Initialize the linear scale condition file in the
(LINEAR SCALE check. maintenance mode, and then load the linear
FILE) • The memory for the linear scale scale condition file saved in the external
4063 MEMORY ERROR --- An error was detected at memory Initialize the conveyor condition auxiliary file
(CONVEYOR check. in the maintenance mode, and then load the
COND SUPP.) • The memory for the conveyor conveyor condition auxiliary file saved in the
condition auxiliary file is external memory device.
damaged.
4064 MEMORY ERROR --- An error was detected at memory Initialize the weaving synchronizing welding
(WEAVING check. condition file in the maintenance mode, and
SYNCHRONIZING • The memory for the weaving then load the weaving synchronizing welding
WELD FILE) synchronizing welding condition condition file saved in the external memory
4065 MEMORY ERROR --- An error was detected at memory Initialize the I/F panel file in the maintenance
(I/F PANEL FILE) check. mode, and then load the I/F panel file saved
• The memory for the I/F panel file in the external memory device.
is damaged.
4069 MEMORY ERROR --- An error was detected at memory Initialize the palletizing condition file in the
(PALLETIZING check. maintenance mode, and then load the
COND FILE) • The memory for the palletizing palletizing condition file saved in the external
4100 OVERRUN --- One of the manipulator overrun limit Move back the manipulator out of the overrun
(ROBOT AXIS) switches activated. limit switch range. (Refer to the
INSTRUCTIONS.)
8-41
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
4101 OVERRUN --- One of the external-axis overrun Move back the external axis out of the
(EXTERNAL AXIS) limit switches activated. overrun limit switch range. (Refer to the
INSTRUCTIONS.)
4102 SYSTEM DATA 1 The system parameters are Turn the power OFF then back ON.
HAS BEEN modified.
CHANGED • An attempt was made to turn ON
the servo power supply after
having modified the system
parameters.
The data indicates the cause of
alarm.
1: System parameter modified
An error occurred in the independent control
startup operation.
1 • Sub task being executed: Complete the sub task by PWAIT command.
Although a job is being executed
by instructed sub task, an attempt
was made to execute another job
by the sub task.
2 • Group axis being used:
The job operated by another sub
task uses the same group axis.
Check the job to be started and the execution
3 • Multiple start of same job: timing for start command again.
PARALLEL START The job that was tried to be
4103 INSTRUCTION started was executed by another
ERROR sub task.
4 • Unregistered master job: Register the master job for sub task.
Although the master job was not
registered, an attempt was made
to execute PSTART SUB (job
name omitted).
5 • Synchronization instruction error: Check the job to be started and the execution
When restarted by PSTART, timing for start command again.
synchronization instruction status
of the sub task under interruption
was different from the status to
restart.
An error occurred in the independent control
startup operation.
PARALLEL START
4103 INSTRUCTION 6 • Stopped by an alarm: Reset the alarm, and then start the sub task.
ERROR An attempt was made to start the
sub task which is stopped by an
alarm.
4104 WRONG --- An error occurred when an Reset the alarm, and then remove the cause
EXECUTION OF instruction was executed by the according to the alarm data.
LOAD INST data transmission DCI function.
alarm.
(Refer to the manual for Data
Transmission Function for details.)
SAVE INST data transmission DCI function.
alarm.
8-42
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
DELETE INST data transmission DCI function.
alarm.
4107 OUT OF RANGE --- The position difference between • Move the manipulator or station to the zero
(ABSO DATA) when the power was turned OFF position by the axis operation and check the
and when the power was turned home position alignment marks (the arrow).
ON again exceeded the tolerance • If the zero position does not match the
for the manipulator or a station. home position, check if there is no error in
the PG system of the axis for which the
alarm occurred.
4109 DC24V POWER 0000_ The external 24V power for I/Os is • Check if the fuse of robot I/F unit (NIF) is not
SUPPLY 00∗∗ not output. blown.
FAILURE (I/O) 0000_0001: Fuse blown (NIF01 • Check the 24V external power supply.
unit) • Check the communications cable for the I/O
0000_0011: External 24 V power module
supply error If the error occurs again, contact your
4110 SHOCK SENSOR --- The shock sensor activated. Remove the cause of shock sensor
ACTIVATION activation.
4111 BRAKE FUSE --- The brake fuse blew out. Replace the fuse.
BREAKDOWN
An error occurred during data transmission.
1 • Retry over of NAK
DATA SENDING
4112 2 • Retry over for timeout in timer A
ERROR Reset the alarm, and then remove the cause.
3 • Retry over for mutual response
error
1 • Reception timeout (timer A) Reset the alarm, and then remove the cause.
2 • Reception timeout (timer B)
DATA RECEIVING 3 • Heading length is too short.
4113
ERROR 4 • Heading length is too long.
5 • The header No. error
6 • The text length exceeded 256
characters.
DATA RECEIVING
4113 7 • An unexpected control code was
ERROR Reset the alarm, and then remove the cause.
received.
1 • Overrun error
TRANSMISSION 2 • Parity error
4114 HARDWARE
ERROR 3 • Framing error Reset the alarm, and then remove the cause.
4 • Transmission timeout (timer A)
5 • Transmission timeout (timer B)
8-43
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
(This alarm occurs when received data
cause inconsistency on the system although
the transmission protocol is correct. Mainly,
this alarm occurs due to an illegal
transmission or erroneous report at the data
TRANSMISSION sending side.)
4115
SYSTEM BLOCK 1 • Received EOT while waiting ACK.
2 • Received EOT while waiting ENQ.
3 • Received EOT before last block Reset the alarm, and then remove the cause.
reception.
4 • Received codes other than EOT
after last block reception.
4116 TRANSMISSION --- An error occurred during data If the error occurs again, contact your
SYSTEM ERROR transmission. Yaskawa representative.
4117 BRAKE POWER --- The power for brake is not output. • Verify the brake wiring. If the fuse is blown,
ERROR An error occurred due to ground check the wiring, then replace the fuse.
fault or short circuit of the brake If the error occurs again, contact your
wiring. Or the fuse of optional unit Yaskawa representative.
(NBP¨¨) or brake release unit
(NBU¨¨) is blown.
4118 TRIPPED CIRCUIT XY The circuit protector of the in-panel • Verify the wiring of in-panel cooling fan.
PROTECTOR OF cooling fan is tripped due to ground If there is no defect in the wiring, replace the
IN-PANEL FAN fault or short circuit or the in-panel cooling fan since the fan may be defective.
cooling fan, or defective fan.
Note: This alarm is displayed
approximately one minute
after the detection.
X···Servo board
1: Servo board1 (SV#1)
Y···Power-ON unit
4119 FAN ERROR X The rotation speed of in-panel • Reset the alarm, and then move the
(IN CONTROL cooling fan decreased. manipulator to the safe position in the teach
BOX) X···CPS unit number mode.
1: CPS unit 1(Detected with SV#1) • Check if in-panel cooling fan is rotating.
2: CPS unit 2(Detected with SV#2) If the fan is not working, verify its wiring.
3: CPS unit 3(Detected with SV#3) Should the error persist, replace the in-panel
4: CPS unit 4(Detected with SV#4) cooling fan (CPS power unit).
8-44
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
4121 COOLING FAN 1 XY The rotation speed of the cooling • Reset the alarm, and then move the
ERROR fan 1 with alarm sensor connected manipulator to the safe position in the teach
to the contactor unit decreased. mode.
X···Servo board • The cooling fan 1 needs to be replaced.
1: Servo board1 (SV#1) Contact your Yaskawa representative.
1 An error occurred when the
notification of the APP task re-
initialization was processed in the
Ethernet function. • Rotate the mode selector switch on the
2 An error occurred when the re- programming pendant to release the mode
initialization response was received setting which has been set to "REMOTE",
in the Ethernet function. then rotate the switch again to set back to
NETWORK "REMOTE".
3 The incomplete task of re-
4130 APPLICATION • If the error occurs again after releasing the
initialization was unsuccessfully
ERROR mode setting of the switch and setting back
completed in the Ethernet function.
to "REMOTE", turn the power OFF then
4 An error occurred when the back ON.
semaphore for re-initialization was If the error occurs again, contact your
received in the Ethernet function. Yaskawa representative.
5 An error occurred when the re-
initialization mail was sent in the
Ethernet function.
8-45
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
6 An error occurred in the exclusive
process of the storage area control
table of the Ethernet function.
7 Time-out occurred in the re-
initialization response receiving
8 An error occurred in the re-
initialization response receiving
9 Receiving data size error occurred
in the re-initialization response
receiving process of the Ethernet
function.
task mail receiving process of the
Ethernet function.
Ethernet function.
32 An error occurred in the FTP client
Ethernet function.
40 Illegal e-mail data were received in
the Web server task of the Ethernet
function. • Rotate the mode selector switch on the
programming pendant to release the mode
41 Illegal e-mail data were received in setting which has been set to "REMOTE",
the FTP server task of the Ethernet then rotate the switch again to set back to
function. "REMOTE".
NETWORK
42 Illegal e-mail data were received in • If the error occurs again after releasing the
4130 APPLICATION
the FTP client task of the Ethernet mode setting of the switch and setting back
ERROR
function. to "REMOTE", turn the power OFF then
50 An error occurred in the data size back ON.
written to PCI of the Ethernet If the error occurs again, contact your
funciton. Yaskawa representative.
51 An error occurred when the request

to write PCI data was received in
52 The request of the undefined
transmission was received in the
Ethernet function.
53 An error occurred in the
transmission request of the
Ethernet function.
54 The transmission request without
data was received in the Ethernet
function.
55 The transmission request of illegal
data length was received in the
Ethernet function.
60 Illegal mail data ware received in
the DNS task of the Ethernet
function.
61 Illegal mail data was transmitted in
the DNS task of the Ethernet
function.
100 An error occurred in storing process
of memory which is used in the
Ethernet function.
8-46
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
101 An error occurred in the buffer for • Rotate the mode selector switch on the
request to write PCI getting process programming pendant to release the mode
of the Ethernet function. setting which has been set to "REMOTE",
200 The socket of the Ethernet function then rotate the switch again to set back to
NETWORK was full and was not able to create "REMOTE".
4130 APPLICATION a socket. • If the error occurs again after releasing the
ERROR mode setting of the switch and setting back
201 An error occurred in the semaphore to "REMOTE", turn the power OFF then
of socket control table of the back ON.
Ethernet function. If the error occurs again, contact your
1 An error occurred in the creation of
receiving socket during the UDP
2 An error occurred in the creation of
transmission socket during the
UDP process of the Ethernet
function.
3 Illegal data were received in the
function.
4 Transmission error occurred in the
function. • Rotate the mode selector switch on the
5 The SELECT operation was not programming pendant to release the mode
successfully completed in the UDP setting which has been set to "REMOTE",
process of the Ethernet function. then rotate the switch again to set back to
UDP "REMOTE".
4131 COMMUNICATION 100 The re-initialization notification of • If the error occurs again after releasing the
ERROR illegal data length was received in mode setting of the switch and setting back
the UDP process of the Ethernet to "REMOTE", turn the power OFF then
function. back ON.
101 The re-initialization notification of If the error occurs again, contact your
illegal data was received in the Yaskawa representative.
function.
102 The PCI write process was not
successfully completed in the UDP
data length was received in the
function.
data was received in the UDP
1 The socket table was not
successfully created in the TCP • Rotate the mode selector switch on the
process of the Ethernet function. programming pendant to release the mode
2 An error occurred in the process of setting which has been set to "REMOTE",
the TCP server initialization of the then rotate the switch again to set back to
TCP Ethernet function. "REMOTE".
4132 COMMUNICATION • If the error occurs again after releasing the
ERROR 3 An error occurred in connection mode setting of the switch and setting back
detecting process of TCP server of to "REMOTE", turn the power OFF then
the Ethernet function. back ON.
4 An error occurred in the connection If the error occurs again, contact your
detection checking process of TCP Yaskawa representative.
server of the Ethernet function.
0 TOYOPUC is in stopped state. Use the PCwin, etc. to run the TOYOPUC,
TOYOPUC RUN
4135 then reset the alarm for the NX100, or turn
STOP
ON the power supply again.
8-47
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
0 The PCI bus state of the
TOYOPUC turns to "ER".
An error occurred in the processing
on the TOYOPUC side.
1 INTRB time-out error • Rotate the mode selector switch on the
An error occurred in the PCI bus programming pendant to release the mode
communication processing of the setting which has been set to "REMOTE",
TOYOPUC. then rotate the switch again to set back to
2 The INTPC does not turn to "1" five "REMOTE".
TOYOPUC
4136 seconds after the PCI command is • If the error occurs again after releasing the
MAJOR ERROR
issued. mode setting of the switch and setting back
An error occurred in the PCI bus to "REMOTE", turn the power OFF then
communication processing of the back ON.
TOYOPUC. If the error occurs again, contact your
3 Error in the state of interrupt
register1
An error occurred in the PCI bus
communication processing of the
TOYOPUC.
1 An error occurred at SETUALM Specify the alarm in the range 8000 to 8999.
instruction execution.
Alarm code specification error
2 An error occurred at SETUALM Specify the task in the range 0 to 4 (7 at
4137 SETUALM ERROR instruction execution. expansion).
Task specification error
3 An error occurred at SETUALM Set the motion mode to 0 or 1.
Motion mode specification error
--- An error occurred at SVON • Verify that the external servo ON (EXSVON)
instruction execution. is short-circuited.
4138 SVON ERROR SVON is disabled. • Verify that the concurrent I/O signal #80031
(servo ON condition1) and #80033 (servo
ON condition2) are turned ON.
4139 PRINT ERROR --- An error occurred at PRINT Review the PRINT output conversion spec
instruction execution. (character string specification).
PRINT output conversion spec
(character string specification) error
An error occurred at execution of the
DIALOG instruction.
1 DIALOG instruction control error • Reset the alarm, and then try again.
• Turn the power OFF and back ON.
4140 DIALOG ERROR 2 Messages and buttons are not
registere.
3 Buttons are not registered. Review DIALOG instruction.
4 The length of character string was
exceeded.
1 The error on setting of time
difference value occurred in the
SNTP process of the Ethernet
function.
• Turn the power OFF and back ON.
2 The error on setting of time-out
4141 SNTP ERROR If the error occurs again, contact your
value occurred in the SNTP
3 The error on setting of reference
interval value occurred in the SNTP
8-48
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
4 The IP address error occurred in • Correctly set the IP address of the SNTP
the SNTP process of the Ethernet server.
function. • If the DHCP is used, verify the DHCP server
operation and the network status.
5 Time-out occurred in the SNTP Verify the SNTP server operation and the
process of the Ethernet function. network status.
6 The server time is not synchronized Verify the SNTP server operation.
in the SNTP process of the
Ethernet function.
7 The SNTP process of the Ethernet Use the server compliant with the SNTP
function is not compliant with the version 3.
version that the server sent.
8 Illegal parameters were found in the
4141 SNTP ERROR • Verify the SNTP related settings.
function.
9 The SNTP process of the Ethernet Yaskawa representative.
function was not successfully
completed.
10 The name resolution error occurred • Set a correct IP address for the SNTP
in the SNTP process of the server.
Ethernet function. • When the DHCP is used, verify the DHCP
server operation and the network status.
11 The error on getting of server
• When the DHCP is used, verify the DHCP
address occurred in the SNTP
server operation.
12 The server setting is incorrect in the
• Set a correct IP address for the SNTP
server.
function.
4200 SYSTEM ERROR --- An error occurred during the access • Reset the alarm, and then try again.
(FILE DATA) to file data (during file edition or • Turn the power OFF then back ON.
external memory device operation). If the error occurs again, contact your
An error occurred when accessing to job • Reset the alarm, and then try again.
data. • Turn the power OFF then back ON.
-1 • An error occurred in parameter If the error occurs again, contact your
specification. Yaskawa representative.
-2 • Access time exceeded the limit.

-3 • The access to a job could not be
performed with the specified job
name.
-4 • The character not allowed was
used as a job name.
-5 • A job was newly created with the
same name of the job already
SYSTEM ERROR specified in the memory.
4201
(JOB)
-6 • The allowable job registration Delete unused jobs and/or expand CMOS.
area (memory) was exceeded.
-7 • A job that did not exist in the • Reset the alarm, and then try again.
memory was specified. • Turn the power OFF then back ON.
-8 • An attempt was made to change Release the prohibition and change it.
the contents for the job prohibited
from being edited.
-9 • An error occurred in handle value. • Reset the alarm, and then try again.
• Turn the power OFF then back ON.
8-49
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
-10 • An error occurred in job data • Reset the alarm, and then try again.
control system. • Turn the power OFF then back ON.
-11 • An error occurred in sequence If the error occurs again, contact your
number of the accessed job. Yaskawa representative.
-12 • An error occurred in step number

of the accessed job.
-13 • A job specified at job search did
not exist in the memory.
-14 • There was an instruction that did Check the NCP01 and NCP02 software
not exist in a job because of versions before/after updating.
inconsistency of the system
software.
SYSTEM ERROR
4201 -16 • Unused handles were lacking • Reset the alarm, and then try again.
(JOB)
when an attempt was made to • Turn the power OFF then back ON.
open a job. If the error occurs again, contact your
-18 • The number of instructions added Delete unnecessary instructions and add
to a job exceeded 9999. new instructions.
-19 • The number of steps added to a Delete unnecessary steps and add new
job exceeded 9999. steps.
-20 • A job was newly created with the • Reset the alarm, and then try again.
same name of the undefined job • Turn the power OFF then back ON.
already specified in the memory. If the error occurs again, contact your
-99 • A job data in the memory was Yaskawa representative.
destroyed.
An error occurred when accessing to job • Reset the alarm, and then try again.
data. • Turn the power OFF then back ON.
1 • An error occurred in parameter If the error occurs again, contact your
specification. Yaskawa representative.
2 • Access time exceeded the limit.

3 • The access to a job could not be
performed with the specified job
name.
4 • The character not allowed was
used as a job name.
5 • A job was newly created with the
same name of the job already
specified in the memory.
SYSTEM ERROR
4202 6 • The allowable job registration Delete unused jobs and/or expand CMOS.
(JOB)
area (memory) was exceeded.
7 • A job that did not exist in the • Reset the alarm, and then try again.
memory was specified. • Turn the power OFF then back ON.
8 • An attempt was made to change Release the prohibition and change it.
the contents for the job prohibited
from being edited.
9 • An error occurred in handle value. • Reset the alarm, and then try again.
10 • An error occurred in job data • Turn the power OFF then back ON.
control system. If the error occurs again, contact your
11 • An error occurred in sequence
number of the accessed job.
8-50
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
12 • An error occurred in step number • Reset the alarm, and then try again.
of the accessed job. • Turn the power OFF then back ON.
13 • A job specified at job search did If the error occurs again, contact your
not exist in the memory. Yaskawa representative.
14 • There was an instruction that did Check the NCP01 and NCP02 software
not exist in a job because of versions before/after updating.
inconsistency of the system
software.
16 • Unused handles were lacking • Reset the alarm, and then try again.
when an attempt was made to • Turn the power OFF then back ON.
SYSTEM ERROR open a job. If the error occurs again, contact your
4202
(JOB) Yaskawa representative.
18 • The number of instructions added Delete unnecessary instructions and add
to a job exceeded 9999. new instructions.
19 • The number of steps added to a Delete unnecessary steps and add new
job exceeded 9999. steps.
20 • A job was newly created with the • Reset the alarm, and then try again.
same name of the undefined job • Turn the power OFF then back ON.
already specified in the memory. If the error occurs again, contact your
99 • A job data in the memory was Yaskawa representative.
destroyed.
An error occurred in position data control
process.
-1 • The memory area for position data
is lacking at the initialization of the
position data control process. Initialize the job in the maintenance mode.
-2 • The number of axes for all the
control groups is zero at the
initialization of the position data
control process.
-3 • The number of axes for position • When the data is loaded from the external
data is zero. memory, the control axis for external
memory is different from that for system.
Initialize the job.
• When a point is added, the job is not
initialized after the control axis for system
was changed to a different control group by
system configuration. Initialize the job.
-4 • The number of stored position
SYSTEM ERROR
4203 data exceeded the maximum
(POSITION DATA)
stored data at the initialization of
the position data control process.
-5 • The memory size of the position
data exceeded the maximum Initialize the job in the maintenance mode.
memory size at the initialization of
-6 • Unused position data file is
destroyed.
-7 • Unused position data file does not Delete unnecessary steps (position data) and
exist. add position data.
-8 • Position data file is destroyed.
-9 • Position data control information is

destroyed. Initialize the job in the maintenance mode.
-10 • An error occurred in specified

position data number.
8-51
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
-11 • Position data is not registered.
-12 • An attempt was made to access

the undefined position data.
-13 • An attempt was made to access

the position data for the undefined
control group.
SYSTEM ERROR -14 • Position data control is not If the error occurs again, contact your
4203
(POSITION DATA) initialized. Yaskawa representative.
-15 • The number of axes for the control

groups exceeded the limit.
-16 • An error occurred in exclusive

control.
-17 • An error occurred in exceptional

control.
An error occurred in position data control

process.
1 • The memory area for position data
is lacking at the initialization of the
position data control process. Initialize the job in the maintenance mode.
2 • The number of axes for all the
control groups is zero at the
initialization of the position data
control process.
3 • The number of axes for position • When the data is loaded from the external
data is zero. memory, the control axis for external
memory is different from that for system.
Initialize the job.
• When a point is added, the job is not
initialized after the control axis for system
was changed to a different control group by
system configuration. Initialize the job.
4 • The number of stored position
data exceeded the maximum
stored data at the initialization of
SYSTEM ERROR the position data control process.
4204
(POSITION DATA) 5 • The memory size of the position
data exceeded the maximum Initialize the job in the maintenance mode.
memory size at the initialization of
6 • Unused position data file is
destroyed.
7 • Unused position data file does not Delete unnecessary steps (position data) and
exist. add position data.
8 • Position data file is destroyed.
9 • Position data control information is

destroyed. Initialize the job in the maintenance mode.
10 • An error occurred in specified

position data number.
11 • Position data is not registered.

12 • An attempt was made to access Yaskawa representative.
the undefined position data.
8-52
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
13 • An attempt was made to access
the position data for the undefined
control group.
14 • Position data control is not
initialized.
SYSTEM ERROR 15 • The number of axes for the control If the error occurs again, contact your
4204
(POSITION DATA) groups exceeded the limit. Yaskawa representative.
16 • An error occurred in exclusive

control.
17 • An error occurred in exceptional

control.
4206 SYSTEM ERROR --- An error occurred in data • Turn the power OFF then back ON.
(TRANSMISSION) transmission. If the error occurs again, contact your
A system error occurred in MOTION. • Reset the alarm, and then try again.
1 • An interrupt undefined in the main • Turn the power OFF then back ON.
command from the system control If the error occurs again, contact your
section occurred. Yaskawa representative.
2 • An interrupt undefined in the sub

command from the system control
section occurred.
3 • The interrupt command that was
sent previously from the system
control section is being
processed.
4 • An error was detected in the
interrupt command data from the
system control section.
5 • An undefined command was
detected in the sub segment task
of MOTION.
detected in the servo-related
processing of MOTION.
SYSTEM ERROR
4207 7 • An undefined command was
(MOTION)
detected in the offline processing
task of MOTION.
detected in the utility task of
MOTION.
10 • Task Token is not generated.
11 • Mail-box Token is not generated.
12 • Semaphore Token is not
generated.
13 • Memory-pool Token is not
generated.
14 • RMS receiving data error
15 • RMS sending data error
16 • RMS receiving unit error
17 • RMS sending unit error
18 • Task generation error
19 • Mail-box generation error
20 • Semaphore generation error
8-53
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
21 • Token pointer error • Turn the power OFF then back ON.
22 • TCB area overflow Yaskawa representative.
23 • Stack area overflow
24 • Mail-box area overflow
25 • Semaphore area overflow
30 • Main command error
31 • MSS system - ID number error
32 • HA-MSS system number error
33 • Incorrect control group
designation
34 • Offline bank semaphore reception
error
35 • m_gen_area semaphore
reception error
36 • Offline HA processing timeout
37 • DM_BANK flag error (DM_BANK
conversion processing)
38 • S → M offline processing
command type error
39 • SL data transmission request
function error
40 • Error in designation of application
in the request of general-purpose
SYSTEM ERROR
4207 data preset for each application.
(MOTION)
41 • Error in the parameter to prepare
the speed data table
the global-variable control table
the axis control table
the online servo-constant
modification table
45 • Mail-box of sequence task is not
ready.
46 • Control-group usage undefined
47 • Segment task polling command
error
48 • Physical axis number error
49 • The control group impossible to
release the brake
50 • Sub-segment request FULL
51 • Sub-segment process timeout
52 • Data latch request FULL
53 • Data latch process timeout
54 • AXIS command request FULL
55 • AXIS command process timeout
56 • Positioning monitor request FULL
8-54
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
57 • Positioning monitor process • Turn the power OFF then back ON.
timeout If the error occurs again, contact your
58 • Failed AXIS servo OFF command
request during emergency stop
60 • Memory pool area overflow
61 • Conversion primary expression for
Power Source command ↔ EW
command not prepared
62 • Duplicated request error during
master control-group tracking
63 • GVM shared resource semaphore
error
64 • Job queue DEQUE error
65 • Conversion primary expression for
painting device command ↔ EW
command not prepared
66 • Execution system decision table
not set
67 • Unknown mode data (Without
TEACH/PLAY mode data)
68 • Shift-value output timeout of the
general-purpose sensor
69 • Interrupt main status set
71 • System number error at the
master side in twin synchronous
SYSTEM ERROR system
4207
(MOTION) 72 • No data link added to the
command
73 • Setting status error of the user
coordinates file
75 • Previous path data reference error
76 • Target position preparation error in
arc-retry shift motion mode
77 • Request to compensate position
error of the axis that is not
endless axis
79 • Inner track zone status error
80 • Instruction queue and instruction
system data area overflow
81 • Offline answer bank flag error
82 • Path and trace queue ENQUE
BANK error
83 • Pending and block end request
FULL
84 • Base axis file type error
85 • Output buffer SYSCON for
automatic test data in use
86 • Conversion completion status for
AXIS section feedback latch data
not established
87 • Sensor number (SL#) error
88 • File C1 through C3 for calibration
between manipulators not set
8-55
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
89 • File C1 through C3 for conveyor • Turn the power OFF then back ON.
calibration not set If the error occurs again, contact your
90 • HA function error
(conv_pos_data())
(conv_shift_data())
(trans_angle_to_pulse())
(trans_pulse_to_angle())
(conv_pulse_to_angle())
(pr_atinf_pos_make())
(make_pos_data())
100 • Control-group axis configuration
information parameter error
101 • Error in the parameter for the table
for physical axes
102 • Error in the parameter for the table
for physical TU
103 • Excessive number of control
group axes in use
SYSTEM ERROR 104 • JOG and PLAY maximum speed
4207
(MOTION) setting parameter error
120 • Job argument over
121 • Job argument stack overflow
122 • Job argument stack underflow
123 • Designation error of the fetched
feedback pulse area at
preparation of current value
128 • Timeout for waiting permission to
modify the number of averaging
times
129 • Object undefined for CLEAR
instruction
130 • No space in RT_BANK setting
area for correction-amount data
131 • Queue operation error for variable
write-in history at prereading (at
ENQUE)
write-in history at prereading (at
DEQUE)
write-in history at prereading
(undefined operation)
write-in history at prereading
(data length too long)
8-56
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
135 • Queue operation error for score- • Turn the power OFF then back ON.
board setting history (at ENQUE) If the error occurs again, contact your
136 • Queue operation error for score-
board setting history (at DEQUE)
board setting history (undefined
operation)
board setting history (data length
too long)
139 • Queue operation error for
instruction execution (at ENQUE)
instruction execution (at DEQUE)
instruction execution (undefined
operation)
instruction execution (data length
too long)
143 • Queue operation error for WORK
ID conveyor (at ENQUE)
ID conveyor (at DEQUE)
ID conveyor (undefined
SYSTEM ERROR operation)
4207
(MOTION)
ID conveyor (data length too long)
IN/OUT checking conveyor (at
ENQUE)
IN/OUT checking conveyor (at
DEQUE)
IN/OUT checking conveyor
(undefined operation)
IN/OUT checking conveyor (data
length too long)
151 • Queue operation error for waiting
for semaphore for LOCK
instruction (at ENQUE)
instruction (at DEQUE)
instruction (undefined operation)
instruction (data length too long)
222 • Impossible to execute system
exclusive for system job
8-57
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
223 • Event queue number range • Turn the power OFF then back ON.
exceeded If the error occurs again, contact your
224 • No motor-gun control group for
ESRCH instruction
225 • The number of WORK ID data and
the MAX. WORK FIND COUNT
unmatched (MOTION ≠ CV)
226 • The number of WORK IN/OUT
data and the MAX. WORK FIND
COUNT unmatched (MOTION ≠
CV)
227 • Excessive number of scheduling
for execution of instructions
228 • Instruction execution scheduling
impossible
229 • Illegal 1st-line move instruction at
execution of +SMOV instruction
230 • Impossible to execute the slave
circular interpolation and the
master circular interpolation at the
same time
231 • Impossible to execute the slave
spline interpolation and the
master spline interpolation at the
same time
SYSTEM ERROR 232 • Illegal index value for a +MOVx
4207
(MOTION) instruction
233 • No xth-line move instruction exists
where the master control group
belongs.
234 • Marking error for WORK ID
conveyor queue (empty queue)
235 • Marking error for WORK IN/OUT
conveyor queue (empty queue)
236 • Data error 1 at restarting after an
emergency stop (actual status
and the data status unmatched)
239 • Timeout for receiving segment
data output request
240 • The number which designates the
setting area of correction amount
in RT_BANK exceeded the limit
value.
241 • Task error of the function calling
source (cv_sync_intr ( ))
242 • No control group for motor gun for
clearance move instruction
8-58
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
243 • Motor gun condition file number • Turn the power OFF then back ON.
error (including gun pressure file) If the error occurs again, contact your
244 • GETTOOLW manipulator
designation error
245 • Overflow of entry number for
instruction execution
246 • Data latch processing (function
number overflow)
247 • Data latch processing (real-time
status number overflow)
248 • Failed to set a timer unit. (No
allocation space for timer unit
setting)
249 • Segment data missing (seg_t_req
was not received in time.)
250 • GETS instruction internal error
251 • SETFILE undefined file
252 • GETFILE undefined file
253 • The parameter was destroyed
SYSTEM ERROR when a GETPRM instruction was
4207
(MOTION) executed.
254 • Null pointer assignment detected
255 • Function or other processing
parameter error
1000 • System clock (RTC) setting error
1001 • System task priority arrangement
error
1002 • VxWorks primitive error
(msgQCreate)
(msgQSend)
(msgQReceive)
(semBCreate)
(semGive)
(semTake)
2000 • Failed system job environment
configuration
A system error occurred in the path control
section.
1 • Prereading task is not completed.
2 • The answer bank flag is already
set.
3 • Inner path motion is impossible. • Reset the alarm, and then try again.
SYSTEM ERROR
4208 If the error occurs again, contact your
(ARITH) 4 • Error in the number of position Yaskawa representative.
data
5 • The averaging buffer in the
arithmetic section is destroyed.
6 • No previous bank exists.
7 • The answer bank flag is ON.
8-59
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
section.
8 • An error occurred in preparation of
current position.
9 • Mails could not correctly be
received in the current task.
10 • Spline-curve path designation
error
11 • The previous bank’s prereading
conversion could not correctly be
completed.
12 • A manipulator designation error
occurred at JOG operation using
the external reference point.
13 • Designation error of cubic
interference coordinates
14 • Path control position data error of
prereading bank
15 • Weaving control position data
error of prereading bank
16 • Station/base axis motion
command error
18 • User coordinates number error
19 • Processing error in re-preparation
of segment control data
20 • Prereading task not completed at
master in twin synchronous • Reset the alarm, and then try again.
SYSTEM ERROR system
(ARITH)
21 • Zero division occurred at observer Yaskawa representative.
operation.
22 • Processing error in optimized
acceleration/deceleration control
23 • Dynamic model arithmetic error
24 • Speed limit control error
(excessive moment of gravity)
25 • Square root of a negative number
26 • The system number is not set at
master in twin synchronous
system.
27 • Designation error of control group
for servo sealer gun
28 • Designation error of control
condition for servo sealer gun
29 • FORMCUT internal control error
30 • Arm interference check error
(radius data referencing mistake)
(miscalculation using direct
kinematics)
32 • Arm interference check error (L-
axis expansion flag setting error)
(check-point re-setting error)
34 • Impossible to edit the averaging
buffer (zero division)
8-60
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
section.
35 • No master-group is designated at • Reset the alarm, and then try again.
preparation of master-tool user If the error occurs again, contact your
coordinates. Yaskawa representative.
37 • Gauging function error (command
designation error)
38 • A coordinated motion was The coordinated motion cannot be performed
attempted using the Following by the Following function. Change the
function. setting so that only the manipulator moves.
39 • Zero or a negative value is set for Set a positive value for the bending speed.
the bending speed of the
Following function.
40 • Zero or a negative value is set for Set a positive value for the bending stroke.
the bending stroke of the
Following function.
SYSTEM ERROR 41 • Pulse linked JOG function error
4208
(ARITH) 42 • Special JOG operation error • Reset the alarm, and then try again.
43 • Following function error (The used
manipulator model does not
support 7-axis Following Control.)
45 • The speed control in the non- Confirm the following settings for the
excessive segment function was teaching position.
failed. • Change the teaching position and posture.
When the teaching position is close to the
manipulator and the LU-axes angle is
small, modify the teaching position so that
the position is away from the manipulator
and the LU-axes angle becomes larger.
If the teaching position is around a singular
point, change the posture with care not to
pass the singular point.
• Change the teaching speed.
Set a smaller value for the teaching speed
than the value at the alarm occurrence.
A system error occurred in the offline
position-data preparation section.
100 • Data setting error in offline data
bank
101 • Data setting error in offline answer
bank
102 • OFF_USER_POS occupation
control error
103 • OFF_USER_POS valid control
error
104 • Mail-receiving error of offline task
105 • Offline occupation control error
OFFLINE • Reset the alarm, and then try again.
4209 SYSTEM ERROR 106 • Designation error for offline cubic If the error occurs again, contact your
(ARITH) interference coordinates Yaskawa representative.
107 • OFF_USER_ROT_POS
occupation control error
108 • OFF_USER_ROT_POS valid
control error
109 • OFF_CV_CALIB_POS occupation
control error
110 • OFF_CV_CALIB_POS valid
control error
111 • Incorrect teaching for offline
conveyor tracking turntable
112 • No manipulator is designated for
offline conveyor tracking turntable
function.
8-61
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
An error occurred in local variable control • Reset the alarm, and then try again.
process. • Turn the power OFF then back ON.
-1 • Local variable is not used. If the error occurs again, contact your
-2 • Memory area for local variable
could not be obtained.
-3 • No unused handle value exists
when local variable area is
created.
control.
-5 • Handle value is invalid for
specified local variable.
SYSTEM ERROR -6 • Handle value is incorrect for
4210
(Local variable) specified local variable.
-7 • An error occurred when memory
area for local variable was
released.
-8 • An error occurred when memory
area for local variable was
registered.
-9 • Local variable control process is
not initialized.
-10 • Local variable area shared heap
area.
control.
4215 SYSTEM ERROR --- An error occurred during API • Reset the alarm, and then try again.
(API) processing. • Turn the power OFF and back ON.
4220 SERVO POWER --- The servo power is not supplied to Turn OFF the servo power supply, and then
OFF FOR JOB the job control group axis (control turn ON the servo power supply for the group
group for subcode) to be operated. axis to be operated.
4221 SERVO POWER --- The servo power is not supplied to Turn OFF the servo power supply, and then
OFF FOR JOB the job control group axis (control turn ON the servo power supply for the group
group for subcode) to be operated. axis to be operated.
4222 INPUT 0000_ A dual signal is mutually checking Check the enable switch (DSW and EXDSW)
COMPARISON 00** with the result that Enable switch I/O signal.
ERROR (DSW and EXDSW) I/O signal does
(DSW) not have a match signal as a result
the mutual check of a dual signal.
0000_0001: DSW
0000_0010: EXDSW
1 A safety circuit signal error
SAFE CIRCUIT occurred in I/O unit.
SIGNAL 2 A safety circuit signal error Check the wiring of the safety circuit signal
4223
DISAGREEMENT occurred in I/O unit. cables connected to the I/O contactor unit.
(SERVO) 3 A safety circuit signal error
occurred in I/O unit.
8-62
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
An error occurred in memory play file.
-1 • An error occurred in control
process.
-2 • The arrangement address
information is destroyed for
memory play file system.
-3 • The fixed control information is
destroyed for memory play file
system.
-4 • The memory play file number is
incorrect.
-5 • An attempt was made to newly
register the memory play file
under use.
-6 • An error occurred in checking
written sampling data when the
MEMORY PLAY data was written to CMOS. Needs investigation. Contact your Yaskawa
4224
FILE ERROR -7 • An attempt was made to access representative.
an unused memory play file data.
-8 • The memory play file is destroyed.

-9 • The memory area for sampling
data is full.
-10 • The sampling data is destroyed.
-11 • Data in control process is

incorrect.
-12 • The sampling data is scanned
only at top or end position.
-13 • The memory play file system is

not initialized.
-14 • The offset value is out of range at

sampling data scanning.
4225 SPEED ERROR --- The speed exceeded the limit. Check the motor, board, manipulator motion
(NCP01) Suspected causes include: (influence by external force), and taught ori-
- Motor cable disconnection entation.
- Motor failure
- Defective board due to an external
force applied to manipulator
8-63
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
4228 WRONG DATA --- Chain inconsistency between the • Reset the alarm, and then select WORNG
Job instruction file and position file DATA LOG under SETUP in maintenance
due to following factors: mode to check the factor of the
1 Overlapped chain with the same inconsistency.
position data • Select RESTORE under the pull-down
menu UTILITY to restore the system. If it
2 Unregistered position data is succeeds in restoration, the indication in
chained with the Job instruction the screen changes from "OCCURRED
file. ON" to "RESTORED ON". Then, turn the
3 Registered position data is not control power ON.
chained. For the factor 1 , check the position of the
corresponding file, then correct the position.
For details, refer to "NX100
For the factor 2 , register the position of the
OPTIONS INSTRUCTIONS FOR
corresponding file again.
JOB DATA SIMPLIFIED
• If it fails in restoration, refer to "NX100
RESTORATION FUNCTION
OPTIONS INSTRUCTIONS FOR JOB
(HW0483260)".
DATA SIMPLIFIED RESTORATION
FUNCTION (HW0483260)", and restore the
file system.
1 An error occurred in the acquisition • When the DHCP is used, verify the DHCP
process of the IP address during server operation and the network status.
the IP address monitoring process If the error occurs again, contact your
of the Ethernet function. Yaskawa representative.
2 An error occurred in the acquisition
process of subnet mask during the
network service data creation
process of gateway during the
4 An error occurred in the conversion
process of gateway address during
the network service data creation
ETHERNET
4229 5 An error occurred in the conversion
ERROR
process of DNS server address
during the network service data
creation process of the Ethernet
function.
process of domain during the
process of SNTP server during the
process of host name during the
8-64
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
9 An error occurred in the newest • When the DHCP is used, verify the DHCP
DNS information getting process server operation and the network status.
from DHCP server in the DNS If the error occurs again, contact your
process of the Ethernet function. Yaskawa representative.
10 An error occurred in the setting
process to update DNS information
in the DNS process of the Ethernet
function.
11 An error occurred in the setting
clearing process to update DNS
information in the DNS process of
ETHERNET
4229 20 The subnet mask was not able to
ERROR
be acquired in the DHCP
information update process of the
Ethernet function.
21 Subnet mask update error occurred
in the DHCP information update
25 Gateway update error occurred in
the DHCP information update
26 Gateway clear error occurred in the
DHCP information update process
of the Ethernet function.
4230 REDUCER --- Failed to stop the operation under • Reset the alarm, and then turn ON the
MONITOR OVER the HOLD STOP command. servo again.
• Check the HOLD STOP.
If the error occurs again, replace the servo
control circuit board.
4300 SERVO --- The parameter input value is out of Reset the value within the allowable range.
PARAMETER the allowable range.
ERROR
4301 CONTACTOR --- An error occurred in the contactor • Reset the alarm, and then turn ON the
ERROR due to a defective contactor unit or servo again.
circuit board. • Check the 24-V power supply for I/O.
• The contactor of contactor unit did If the error occurs again, replace the
not turn ON at servo ON. contactor unit or servo control circuit board or
• The signal from the contactor both.
turned OFF while the servo was
ON.
• The signal from the contactor
remains ON when the servo
turned OFF at emergency stop.
• The contactor turned ON while the
servo was OFF for emergency
stop.
4302 BRAKE CIRCUIT --- • The brake relay signal did not turn • Reset the alarm, and then turn ON the
ERROR ON when the servo turned ON. servo again.
• The brake relay signal turned OFF If the error occurs again, replace the
while the servo was ON. contactor unit and/or servo control circuit
• The brake signal remains ON board.
when the servo turned OFF at
emergency stop.
• The brake signal turned ON while
the servo was OFF for emergency
stop.
8-65
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
4303 CONVERTER --- • No response of charge completion • Reset the alarm, and then turn ON the
READY SIGNAL was sent from the converter when servo again.
ERROR the servo turned ON. • Check the primary power supply voltage.
• The SERVO READY signal turned If the error occurs again, replace the servo
OFF while the servo was ON. control circuit board and/or converter.
• The SERVO READY signal
• The SERVO READY signal turned
ON while the servo was OFF for
emergency stop.
• The primary power supply voltage
is too low.
• The voltage dropped.
• Defective servo control and/or
converter
4304 CONVERTER --- • No response of primary power • Check the wiring for the primary power
INPUT POWER supply input was sent from the supply of the SERVOPACK.
ERROR converter when the servo turned • Confirm that the power supply voltage is
ON. 170V or more.
• The READY 1 signal remains ON If the error occurs again, replace the servo
when the servo turned OFF at control circuit board and/or converter.
emergency stop.
• The READY 1 signal turned ON
while the servo was OFF for
emergency stop.
• Incorrect wiring or voltage drop of
primary power supply
• Defective servo control and/or
converter
4305 CONVERTER --- • No response (READY 2 signal) of • Check the wiring for the primary power
CIRCUIT CHARGE charge completion was sent from supply of the SERVOPACK.
ERROR the converter when the servo • Confirm that the power supply voltage is
turned ON. 170V or more.
• The READY 2 signal turned OFF If the error occurs again, replace the servo
while the servo was ON. control circuit board and/or converter.
• The READY 2 signal remains ON
when the servo turned OFF at
emergency stop.
• The READY 2 signal turned ON
while the servo was OFF for
emergency stop.
• Incorrect wiring and/or voltage
drop of primary power supply
• Defective servo control circuit
board, converter, and/or amplifier
4306 AMPLIFIER --- • No response "Power ON" was • Check the wiring for the primary power
READY SIGNAL sent from the amplifier when the supply of the SERVOPACK.
ERROR servo turned ON. • Confirm that the power supply voltage is
• The amplifier READY signal 170V or more.
turned OFF while the servo was If the error occurs again, replace the
ON. WRCA01 circuit board, servo control circuit
• The amplifier READY signal board, converter, and/or amplifier.
• The amplifier READY signal
turned ON while the servo was
OFF for emergency stop.
• Defective servo control circuit
board, converter, and/or amplifier
8-66
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
4307 SERVO ON --- The motion speed of the encoder The control power supply cannot be turned
SPEED ERROR before the dynamic brake turns ON while the manipulator is moving.
OFF in servo ON sequence Stop the manipulator motion, and then turn
exceeded the threshold for a ON the servo power supply.
certain period.
• The servo power supply turned
ON while the manipulator (motor
and encoder) was moving.
4308 VOLTAGE DROP --- The DC power voltage supplied to • Check the wiring for the primary power
(CONVERTER) the SERVOPACK amplifier dropped supply of the SERVOPACK.
below 143V due to: • Confirm that the power supply voltage is
- Low voltage of the primary 170V or more.
power supply If the error occurs again, replace the servo
- Open phase control circuit board, servo control circuit
- Defective converter board, and/or converter.
- Defective servo control
circuit board
4309 DEFECTIVE --- Serial encoder internal parameter • Reset the alarm, and then perform the
ENCODER error occurred. home positioning again. Turn the power
INTERNAL DATA OFF then back ON.
If the error occurs again, replace the motor of
the corresponding axis.
4310 ENCODER --- The temperature of the encoder • Review the load condition and ambient
OVERHEAT exceeded 100 °C. operating temperature.
• Encoder thermistor failure • Confirm that the primary power supply
voltage is 200V + 10%.
control circuit board or the motor.
4311 ENCODER BACK- --- • Encoder resetting (initialization) • Reset the alarm, and then perform the
UP ERROR not completed home positioning again. Confirm that the
• The position data in the encoder encoder backup battery voltage is 2.8V or
was lost due to the voltage drop more.
of encoder backup battery. If the error occurs again, replace the encoder
(motor).
4312 ENCODER --- Encoder backup battery voltage is Confirm that the encoder backup battery
BATTERY ERROR too low. voltage is 2.8V or more. If not, replace the
• The voltage of the encoder battery.
backup battery is below 2.8V.
The position data may be lost.
4313 SERIAL --- The temperature of the encoder • Review the load condition and ambient
ENCODER OVER exceeded 100 °C. operating temperature.
HEAT • Encoder thermistor failure • Confirm that the primary power supply
voltage is 200V + 10%.
control circuit board or the motor.
4314 SERIAL --- Encoder backup battery voltage is Confirm that the encoder backup battery
ENCODER too low. voltage is 2.8V or more. If not, replace the
BATTERY ERROR • The voltage of the encoder battery.
backup battery is below 2.8V.
The position data may be lost.
4315 COLLISION --- • A collision was detected because • Reset the alarm, and then remove the
DETECT of the interference between the object or move the manipulator back to a
manipulator and a peripheral safe position.
device. If the alarm cannot be reset, invalidate the
• The external force applied to the collision detection level setting file or set the
robot exceeded the threshold. detection level higher.
4316 PRESSURE DATA --- The pressure set in the gun Reset the pressure value in the gun pressure
LIMIT pressure file or dry spotting file or dry spotting pressure file below the
pressure file exceeded the maximum pressure value.
maximum pressure set in the gun
condition file.
8-67
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
4317 PRE-LOAD --- The motor does not operate in the Adjust the gun opening.
ERROR pre-load process.
4318 SERIAL --- The speed feedback value of the • Turn the power OFF then back ON.
ENCODER serial encoder exceeded the If the error occurs again, contact your
CORRECT allowable limit. Yaskawa representative.
LIMITATION OVER
4320 OVER LOAD --- The motor torque continuously Check the motor, board, manipulator motion
(CONTINUE) exceeded the rated torque for a (influence by external force), and taught
certain period due to: orientation.
- Motor cable disconnection
- Motor failure
- Defective board
- External force applied to
manipulator, etc.
4321 OVER LOAD --- The torque a several times as much Check the motor, board, manipulator motion
(INSTANT) as the rated torque has been (influence by external force), and taught
applied to the motor due to: orientation.
- Motor cable disconnection
- Motor failure
- Defective board
manipulator, etc.
4322 AMPLIFIER OVER --- The current a several times as • Check the wiring and connection for the
LOAD much as the rated current has motor power line, board, cable
(CONTINUE) continuously flown in the amplifier disconnection, motor type, manipulator
for a certain period. interferences, SERVOPACK, and board,
etc.
Replace if necessary.
4323 AMPLIFIER OVER --- The torque a several times as much • Check the wiring and connection for the
LOAD (INSTANT) as the motor rated torque has motor power line, motor type, manipulator
continuously been applied for a interference, SERVOPACK, and circuit
certain period. boards.
Replace if necessary.
4324 CONVERTER --- The total load value of all the Review the manipulator operating condition
OVER LOAD motors connected to the converter such as reducing the teaching speed, etc.
exceeded the converter rating.
4326 SPEED ERROR --- The speed exceeded the limit due Check the motor, board, manipulator motion
to: (influence by external force), and taught
- Motor cable disconnection orientation.
- Motor failure
- Defective board
manipulator, etc.
4327 MOTOR --- While the motor is accelerating, the Check the wiring and connection for the
ROTATION direction of the torque and the encoder and the motor power line.
ERROR speed was detected as being the
opposite of what it was supposed to
be.
4328 SERVO --- The axis deviated from the • Check the manipulator interferences and
TRACKING specified position and motion path motor power line.
ERROR beyond the allowable range. If the error occurs again, replace the servo
control circuit board, and/or the amplifier or
motor of the corresponding axis.
8-68
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
4330 SPEED --- The read speed monitoring level Check the connection cables for speed
MONITORING signal is disconnected. monitoring unit.
INSTRUCTION
CABLE
DISCONNECTION
4331 SPEED --- Illegal speed monitoring level • Turn the power OFF and back ON.
MONITORING If the error occurs again, replace the AXA01
LEVEL ERROR circuit board.
4332 SPEED CTRL --- An error occurred at speed control • Set an appropriate INERTIA RATIO in the
MODE CHANGE mode setting. MOTOR SPEC window in the maintenance
ERR(SV) • The requested function cannot be mode.
performed. If the error occurs again, replace the servo
control circuit board, external servo control
circuit board, amplifier, and/ or motor.
4334 OVER VOLTAGE --- The DC voltage supplied to the • Check the primary power supply voltage.
(CONVERTER) amplifier exceeded 420V due to: • Reduce the teaching speed and check if the
- Overloaded error occurs. If the error does not occur
- Converter failure with the reduced speed, review the load
- Defective servo control circuit condition.
board If the error occurs again, replace the servo
control circuit board and/or the converter.
4335 EARTH FAULT --- Ground fault of the motor power • Check the motion connection.
line occurred due to: • Remove the motor connector to check the
(If the alarm occurred at an axis conduction between FG and phase U, V
which is driven by a common and W.
converter, all the subject axes are • If there is conduction, replace the lead
indicated.) cable.
- Motor failure • If there is no conduction, replace the motor.
- Ground fault of motor line or lead • If the error occurs again, replace the servo
cables control circuit board or the SERVOPACK.
- Defective servo control circuit board
- Defective SERVOPACK
When this alarm occurs, AL-4337
OVER CURRENT (AMPLIFIER) also
occurs to all the axes driven by a
common converter.
4336 OPEN PHASE --- The SERVOPACK primary power • Correct the SERVOPACK primary power
(CONVERTER) supply is open-phase due to: supply connection,
- Misconnection of primary power • Confirm that the power supply voltage is
supply more than 170V.
- Lowered primary power supply If the error occurs again, replace the servo
voltage control circuit board.
- Defective servo control circuit
board
- Defective converter
4337 OVER --- Ground fault of the motor power • Check the motion connection.
CURRENT line occurred due to: • Remove the motor connector to check the
(AMPLIFIER) - Motor failure conduction between FG and phase U, V
- Ground fault of motor line or lead and W.
cables • If there is conduction, replace the lead
- Defective servo control circuit cable.
board • If there is no conduction, replace the motor.
- Defective amplifier • If no fault is found, turn OFF the power
Also, when AL-4335 EARTH supply to cool down the motor.
FAULT alarm occurs, this alarm • If this natural cooling solves the problem,
occurs to all the axes driven by the the load condition and ambient operating
common converter. temperature must be reviewed and
corrected.
• If the error occurs again, replace the servo
control circuit board or the SERVOPACK.
4338 REGENERATION --- The regenerative energy at motor • Review the load condition and teaching
ERROR deceleration is too large. speed.
(CONVERTER) - The primary power supply voltage • Confirm that the power supply voltage is
is too high (above 242V) 220V ±10%.
- Converter failure If the error occurs again, replace the servo
- Defective servo control circuit control circuit board.
board
4339 INPUT POWER --- The SERVOPACK primary power • Confirm that the power supply voltage is
OVER VOLTAGE supply voltage exceeded 242V. 220V ±10%.
(CONV) If the error occurs again, replace the servo
control circuit board or the converter.
8-69
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
4340 TEMPERATURE --- SERVOPACK (converter) overheat • Confirm that the power supply voltage is
ERROR 220V ±10%.
(CONVERTER) If the error occurs again, replace the servo
4344 LINEAR SERVO --- The deviation of X, Y, and Z-axis Check the job.
FLOAT TRACKING exceeded the allowable limit while
ERROR the linear servo float was in
execution.
4345 LINK SERVO --- The link servo float can not be Check the job.
FLOAT ERROR executed while the linear servo float
is in execution.
4346 LINK SERVO --- The limit torque of the link servo Set the limit torque of the link servo float
FLOAT float condition file is outside the condition file again.
LIMITATION specified range.
TORQUE RANGE
ERROR
4347 LINEAR SERVO --- The limit torque of the linear servo Set the limit torque of the linear servo float
FLOAT float condition file is outside the condition file again.
LIMITATION specified range.
TORQUE RANGE
ERROR
4348 LINEAR SERVO --- While the linear servo float was in Check the job.
FLOAT execution, another request of linear
COORDINATES servo float execution was sent with
TYPE UNMATCH a different coordinates specified.
4349 LINEAR SERVO --- A logical error occurred in the • Reset the alarm, and then try again.
FLOAT TOOL designation for tool orientation • Turn the power OFF then back ON.
POSE CONTROL control of the linear servo float. If the error occurs again, contact your
SPECIFICATION Yaskawa representative.
ERROR
4350 LINEAR SERVO --- While the servo float was in Check the job.
FLOAT execution, the linear servo float can
EXECUTION not be executed.
ERROR
4351 BELT --- The driving belt may be Check the belt, and replace it if necessary.
DISCONNECTION disconnected because the torque
DETECTION decreased below the normal value.
4352 TWIN DRIVE --- The deviation of the position error Check the load.
OVER pulse from the twin drive axis
DEVIATION exceeded the allowable limit with
twin drive function.
4353 DEFECTIVE --- Endless motion impossible Reset the alarm.
TAUGHT POINT • The feedback pulse value
(ENDLESS) exceeded the maximum value
(maximum number of pulses ±
536870912)
4354 FILE NO. ERROR --- The collision detection file for Do not use the collision detection file for
(SHOCK LEVEL) exclusive use for the SVSPOT is exclusive use for the SVSPOT with the
used with the SHCKSET SHCKSET instruction.
instruction.
4355 EXTERNAL PRES --- An external force above the Check the job.
DETECT threshold was detected on the
(SERVOFLOAT) servo-float executing axis.
4356 ARM CTRL --- The search of motor-gun equalizing If the error occurs again, contact your
PARAMETER ERR function cannot be executed Yaskawa representative.
(OBSERVER) because no observer (including
collision detection) is specified.
8-70
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
4357 IMPOSSIBLE --- The manipulator orientation at the Check the job.
SRCH execution of search of the motor-
(EQUALIZE gun equalizing function is the
TEACH) orientation for the singular point.
4358 DUPLICATE --- The pressuring instruction was Do not execute the pressuring instruction
PRESS ERROR executed with manual with manual pressurization during pressuring.
pressurization during pressuring.
4359 CONVERTER --- An error occurred in the converter. • Turn the power OFF then back ON.
ERROR If the error occurs again, replace the servo
4360 WAFER Deci An error occurred in Check the connection of prealigner.
ALIGNMENT mal communications with the
ERROR (SERVO) data prealigner.
4364 GUN SOFT LIMIT --- The gun axis exceeded the • The error could occur due to the tip
software limit during pressuring removed or the tip mis-installation. Verify
operation. the pressuring status.
• Set the pulse software limit again
considering the wearing of chip and the
deflection of gun arm.
4365 EXCESSIVE Physi In comparison to the position, • The error could occur due to the tip
DETECTION cal where the gun electrode hits the removed or the tip mis-installation. Verify
RANGE axis welded target, at the previous wear the pressuring status.
(GUN bit detection, the position during • Adjust the set value of the gun condition file.
ELECTRODE HIT pressuring exceeded the allowable
POINT) limit which had been set in the
motion limit for which the fixed
(movable) gun electrode hits the
welded target.
4366 GUN BENDING Cntrl The function of gun bending • Invalidate the bending correction function.
CORRECTION grp bit correction was performed to the • Contact your Yaskawa representative.
ERROR desig model which was not supported for
nation the function.
4367 ROBOT POSITION Cntrl The manipulator orientation at Check the job.
ERROR grp bit pressuring is the orientation for the
desig singular point.
nation
4371 SYSTEM ERROR Deci The independent brake control was • Turn the power OFF then back ON.
(SERVO) mal performed in TU which was not If the error occurs again, contact your
data supported for the control. Yaskawa representative.
4372 SERVO ON --- The servo OFF status is sent from • Turn the power OFF then back ON.
SIGNAL ERROR TU. If the error occurs again, contact your
8-71
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
The arithmetic process for motion control did
not complete within regulated time.
1 • No motion command was • Reset the alarm, and then try again.
prepared. • Turn the power OFF then back ON.
2 • The arithmetic processing section If the error occurs again, contact your
is not ready for JOG operation. Yaskawa representative.
3 • The arithmetic processing section

is not ready for the playback
operation.
NOT READY
4400 4 • The prereading processing in the
(ARITH)
arithmetic processing section has
not completed.
5 • The arithmetic processing section
is not ready for the timer follow-up
of the conveyor tracking function.
6 • The prereading processing in the
arithmetic processing section has
not completed when specifying
the target position.
An error occurred in job execution process. • Reset the alarm, and then try again.
1 • Unused A_BANK does not exist in • Turn the power OFF then back ON.
the prereading processing of If the error occurs again, contact your
move instruction. Yaskawa representative.
2 • Unused bank priority does not

exist in the prereading processing
of move instruction.
5 • A_BANK pointer is not set.
6 • A_BANK conversion could not be
SEQUENCE TASK performed.
4401 CONTROL 7 • The specified A_BANK number
ERROR does not exist.
20 • An error occurred when system
number (MSS) was obtained.
21 • An error occurred in RMS960
system call.
22 • Undefined interrupt command was
received.
23 • Job start condition is not defined.
24 • An error occurred in instruction
prefetch queue operation.
8-72
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
An error occurred in job execution process. • Reset the alarm, and then try again.
26 • Intermediate code is not defined. • Turn the power OFF then back ON.
29 • Instruction prereading processing Yaskawa representative.
has not been completed normally.
30 • An error occurred in job data
change.
31 • The specified sequence number
at job execution start is incorrect.
32 • The added area for interruption
command is incorrect.
33 • System number (MSS) for
interruption command is incorrect.
38 • An error occurred at start of twin
synchronous operation.
39 • An error occurred when SYNC
specification was reset.
41 • An error occurred in occupation
control group setting in MOTION.
45 • An error occurred in path/trace
control.
47 • An error occurred when waiting for
SEQUENCE TASK a completion of main system task
4401 CONTROL (job) in SYNC specification.
ERROR 48 • An attempt was made to execute
an instruction that could not be
executed at line sequence
execution.
80 • An exceptional error occurred in
job execution process.
100 • Main processing command is
incorrect in prereading
processing.
101 • Subprocessing command is
incorrect in prereading
processing.
102 • Prereading processing has not
been completed at job execution.
103 • A_BANK conversion has not been
completed.
104 • System number (MSS) is incorrect
in prereading processing.
105 • An error occurred in instruction
prefetch queue operation in
prereading processing.
106 • An error occurred at IES switching
in prereading processing.
4402 UNDEFINED An undefined command was issued • Reset the alarm, and then try again.
COMMAND to the path control section. If the error occurs again, contact your
(ARITH) Yaskawa representative.
8-73
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
An error occurred in the arithmetic process • Change the positions so that two arms are
for coordinates. not aligned in a straight line.
1 • The S-arm and L-arm of a scalar • Change the step (move instruction), where
type manipulator are aligned in a the alarm occurred, to MOVJ.
straight line. Interpolation such
as linear and circular interpolation
is impossible in such orientation.
2 • When a vertically-articulated
manipulator was moved by a
special linear interpolation, the R-
axis angle could not correctly be
calculated. Change the position in the step (move
3 • When a vertically-articulated instruction) where the alarm occurred.
manipulator was moved by a
special linear interpolation, the L-
axis angle could not correctly be
calculated.
4 • The L-arm and U-arm of a • Change the positions so that two arms are
vertically-articulated manipulator not aligned in a straight line.
ARITHMETIC are aligned in a straight line. • Change the step (move instruction), where
4404 Interpolation such as linear and the alarm occurred, to MOVJ.
ERROR
circular interpolation is impossible
in such orientation.
6 • The L-arm and U-arm of a
vertically-articulated manipulator
are aligned in a straight line.
Interpolation such as linear and
circular interpolation is impossible
in such orientation.
7 • The TCP of the manipulator is out • Perform the teaching again so that the TCP
of working envelope. of the manipulator is always within the
working envelope.
• Change the shift value so that the TCP of
the manipulator is always within the
working envelope.
8 • Interpolation such as linear and Change the step (move instruction), where
circular interpolation cannot be the alarm occurred, to MOVJ.
performed with this manipulator.
9 • Specified motion cannot be Correct the taught point.
performed with this manipulator.
4405 SELECT ERROR 1 A parameter error occurred in the • Reset the alarm, and turn the power OFF
(PARAMETER) path control section. then back ON.
• Selection error of motion system If the error occurs again, contact your
parameter Yaskawa representative.
An internal control error occurred in a • Reset the alarm, and then try again.
coordinated motion. If the error occurs again, contact your
1 • Designation error for master and Yaskawa representative.
slave
2 • Slave designation error
GROUP AXIS 3 • Slave interpolation error

4406 CONTROL 4 • No designation of master axis
ERROR 5 • No designation of slave axis
6 • Master-axis designation error for
JOG motion
7 • Slave-axis designation error for
JOG motion
8 • Occupation control error
8-74
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
An internal control error occurred in a • Reset the alarm, and then try again.
9 • Designation error of occupation Yaskawa representative.
control for JOG motion
GROUP AXIS
10 • Designation error of occupation
4406 CONTROL
control for Bank position
ERROR
11 • Designation error of occupation
control group for tracking motion
12 • No master and slave designated
for tracking motion
4407 TWO STEPS --- Among three taught points in a Teach the different 3 points again.
SAME POSITION circular interpolation step, two or
(CIRC) three points are on the same point.
4408 TWO STEPS --- Among three taught points in a Teach the different 3 points again.
SAME POSITION spline interpolation step, two or
(SPLINE) three points are on the same point.
4409 TWO STEPS --- Among three taught points to create Teach the different 3 points again.
SAME POSITION an user coordinate system, two or
(3 POINTS) three points are on the same point.
4410 TWO STEPS --- Among three taught points (start, Teach the different 3 points again.
SAME POSITION end, and reference points) to create
(WEAV) a weaving coordinate system, two
or three points are on the same
point.
4411 TEACH ERROR --- The spline interpolation could not Teach the positions so that the distance
(SPLINE) correctly be performed. between the teaching points is even.
• The distance between the
teaching points in the spline
interpolation section is not
equidistant.
4412 IMPOSSIBLE --- Interpolation motion could not be • Perform the teaching again to make the
LINEAR MOTION performed because of different form of L- and U-axes same at start point
(L/U) form of L- and U-axes. and end point.
• In case the form (folded direction) • Use a MOVJ instruction.
of L- and U-axes at start point and
end point are different except for
MOVJ instructions, the
manipulator cannot move.
4413 IMPOSSIBLE --- Interpolation motion could not be • Perform the teaching again to make the
LINEAR MOTION performed because of different form of S- and L-axes same at start point
(S/L) form of S- and L-axes. and end point.
• In case the form (folded direction) • Use a MOVJ instruction.
of S- and L-axes at start point and
end point are different except for
MOVJ instructions, the
manipulator cannot move.
4414 EXCESSIVE --- The manipulator motion speed • Reduce the speed in the step (move
SEGMENT exceeded the limit (LOW level). instruction) where the alarm occurred.
(LOW SPEED) • The manipulator may be near the singular
point. Change the position and orientation
of the manipulator.
4415 EXCESSIVE --- The manipulator motion speed • Reduce the speed in the step (move
SEGMENT exceeded the limit (HIGH level). instruction) where the alarm occurred.
(HIGH SPEED) • The manipulator may be near the singular
point. Change the position and orientation
of the manipulator.
4416 PULSE LIMIT --- The manipulator exceeded its Change the manipulator position in the step
(MIN.) motion limit (pulse limit) in the (move instruction) where the alarm occurred.
negative (−) direction.
8-75
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
4417 PULSE LIMIT --- The manipulator exceeded its Change the manipulator position in the step
(MAX.) motion limit (pulse limit) in the (move instruction) where the alarm occurred.
positive (+) direction.
4418 CUBE LIMIT (MIN.) --- The manipulator TCP exceeded its Change the position in the step (move
motion limit (cube limit) in the instruction) where the alarm occurred.
negative (−) direction.
4419 CUBE LIMIT --- The manipulator TCP exceeded its Change the position in the step (move
(MAX.) motion limit (cube limit) in the instruction) where the alarm occurred.
positive (+) direction.
4420 SPECIAL 0 The manipulator exceeded its Change the position in the step (move
SOFTLIMIT (MIN.) motion limit (special software limit) instruction) where the alarm occurred.
in the negative (−) direction.
SOFTLIMIT (MAX.) motion limit (special software limit) instruction) where the alarm occurred.
in the positive (+) direction.
4422 MECHANICAL 0 The manipulator exceeded its Change the position in the step (move
INTERFERENCE minimum-angle motion limit. instruction) where the alarm occurred.
(MIN.) (Mechanical interference)
4423 MECHANICAL 0 The manipulator exceeded its Change the position in the step (move
INTERFERENCE maximum-angle motion limit. instruction) where the alarm occurred.
(MAX.) (Mechanical interference)
MECHANICAL minimum-angle motion limit. instruction) where the alarm occurred.
INTRF (MIN.) (Special mechanical interference)
MECHANICAL maximum-angle motion limit. instruction) where the alarm occurred.
INTRF (MAX.) (Special mechanical interference)
4426 PULSE --- The manipulator exceeded its Change the position in the step (move
MECHANICAL motion limit (mechanical limit) in the instruction) where the alarm occurred.
LIMIT (MIN.) negative (−) direction.
4427 PULSE --- The manipulator exceeded its Change the position in the step (move
MECHANICAL motion limit (mechanical limit) in the instruction) where the alarm occurred.
LIMIT (MAX.) positive (+) direction.
An error occurred in the real-time processing • Reset the alarm, and then try again.
section that controls the arithmetic section. • Turn the power OFF then back ON.
1 • RT-buffer control command error If the error occurs again, contact your
2 • Segment-receiving control
command error
3 • No bank priority
SEGMENT 4 • Answer error at MOVE simulating
4428 CONTROL 5 • The value of bank_refresh_flag(x)
ERROR exceeded its limit.
6 • Bank refreshing timing error
7 • RT-buffer setting timing error
8 • RT-buffer tracking option error
9 • The segment was received
although the previous segment
had not been sent.
An error occurred in the manipulator
information at job execution.
WRONG 1 • Control group not designated • Reset the alarm, and then try again.
SPECIFIED • Turn the power OFF then back ON.
4429 2 • Slave control-group error
CONTROL If the error occurs again, contact your
GROUP 3 • Master control-group error Yaskawa representative.
4 • Master and Slave control-group
error
8-76
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
An error occurred in the manipulator • Reset the alarm, and then try again.
information at job execution. • Turn the power OFF then back ON.
5 • Control-group error for a job file If the error occurs again, contact your
6 • Control-group error for a user
coordinate file
7 • Control-group error for a
calibration file between
manipulators
8 • Control-group error for a tool
calibration file
9 • Control-group error for a
reference point
10 • Control-group error for
prereading-calculation start point
(for adv_st_pos)
WRONG 11 • Control-group error for the
SPECIFIED current-value preset position
4429
CONTROL
GROUP 12 • Control-group error for the
conveyor prereading-calculation
start point
13 • Occupation control-group error
14 • Control-group error for multi-layer
sampling
15 • Control-group error for servo hand
16 • MRESET control-group error
17 • Control-group error for general-
purpose area of path correction
amount
18 • Control-group error for a conveyor
calibration file
19 • Control-group error for the
prereading-calculation start point
(for dm_st_pos)
An error occurred in interrupt process • Reset the alarm, and then try again.
between CPUs. • Turn the power OFF then back ON.
1 • Interrupt processing error If the error occurs again, contact your
between MOTION and system Yaskawa representative.
control section
2 • Interrupt processing error
between MOTION and SL#1
CPU 4 • Interrupt processing error
4430 COMMUNICATION between MOTION and SL#3
ERROR 5 • Interrupt processing error
between MOTION and CV#1
between MOTION and CV#2
between MOTION and PS#1
between MOTION and PS#2
8-77
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
Data error occurred in job control process. • Reset the alarm, and then try again.
1 • An error occurred in JMS system • Turn the power OFF then back ON.
call when an attempt was made to If the error occurs again, contact your
open a job. Yaskawa representative.
2 • No space was found in job handle

value storage area when an
attempt was made to open a job.
4431 JHM ERROR
3 • No job handle was found.
4 • Job control proprietary is
incorrect.
5 • Job control proprietary could not
be changed.
6 • An error occurred in exclusive
control.
An error occurred in instruction • Reset the alarm, reselect the job, and then
interpretation/execution process. try again.
1 • The intermediate code of the • Delete the instruction where an alarm
instruction that is to be executed occurred, and then reregister and execute
is incorrect. the instruction.
• Delete the job where an alarm occurred,
3 • Destination (variable) tag and then reregister and execute the job.
arrangement is incorrect. If the error occurs again, contact your
4 • Tag data type is incorrect. Yaskawa representative.
5 • Box number is incorrect.
6 • An error occurred in block
separation processing of
intermediate code.
8 • Box number definition is
duplicated.
9 • Undefined instruction was found
at block separation of
intermediate code.
10 • IPRM is not set.
11 • An error occurred in tag data
INSTRUCTION search process.
4432 INTERPRETER 12 • An error occurred move
ERROR instruction search process.
13 • An error occurred reference point
search process.
14 • Variable information does not
exist.
16 • An error occurred at position file
data reading.
17 • Variable data type is not defined.
18 • An instruction is included with
incorrect intermediate code in
expression instruction.
19 • The syntax in expression
instruction is incorrect.
20 • The tag data length is zero when
tag data is read.
21 • The necessary tag data is not set.
22 • The object to be processed was
secret variable in position file
control process, so it could not be
processed.
8-78
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
An error occurred in instruction • Reset the alarm, reselect the job, and then
interpretation/execution process. try again.
23 • The object to be processed was • Delete the instruction where an alarm
position type variable in position occurred, and then reregister and execute
file control process, so it could not the instruction.
be processed. • Delete the job where an alarm occurred,
and then reregister and execute the job.
24 • Job argument settings do not If the error occurs again, contact your
match when a variable is given Yaskawa representative.
and/or taken between jobs.
25 • An attempt was made to perform
INSTRUCTION undefined operation at four-rule
4432 INTERPRETER operation instruction.
ERROR 26 • Arithmetic stack used for
expression operation exceeded.
27 • Arithmetic stack used for
expression operation is empty.
28 • Operation items are lacking in
expression operation and
operation processing cannot be
performed.
254 • Access mechanism for old
parameters is used.
255 • An exceptional error occurred.
The global variable is not defined.
0 • The set data for byte type variable
(S1D parameter) area is incorrect.
1 • The set data for integer type
variable (S1D parameter) area is
incorrect.
2 • The set data for double-precision
integer-type variable (S1D
parameter) area is incorrect.
3 • The set data for real type variable
UNDEFINED (S1D parameter) area is incorrect.
Needs investigation. Contact your Yaskawa
4433 GLOBAL 4 • The set data for character-string representative.
VARIABLE type variable (S1D parameter)
area is incorrect.
5 • The set data for robot-axis
position-type variable (S1D
6 • The set data for base-axis
7 • The set data for station-axis
The local variable is not defined.
0 • The byte type variable is not
defined.
UNDEFINED 1 • The integer type variable is not
Set the number of local variables to be used
4435 LOCAL defined.
in the job header.
VARIABLE 2 • The double-precision integer-type
variable is not defined.
3 • The real-number type variable is
not defined.
8-79
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
The local variable is not defined.
4 • The character-string type variable
is not defined.
UNDEFINED 5 • The robot-axis position-type
Set the number of local variables to be used
4435 LOCAL variable is not defined.
in the job header.
VARIABLE 6 • The base-axis position-type
7 • The station-axis position-type
4436 LESS THAN 3 --- An error occurred in circular Reset the alarm, and then perform teaching
STEP interpolation instruction execution. so that circulation interpolation steps are
(CIRCULAR) • There is no continuous three continuous three points or more.
points or more for circular
interpolation step.
4437 LESS THAN 3 --- An error occurred in spline Reset the alarm, and then perform teaching
STEP interpolation instruction execution. so that spline interpolation steps are
(SPLINE) • There is no continuous three continuous three points or more.
points or more for spline
interpolation step.
4438 UNDEFINED JOB --- The job to be executed is not • Reset the alarm, and then register the job.
registered in the memory. • Delete the CALL/JUMP instruction where
an alarm occurred.
4439 UNDEFINED --- An error occurred in label jump • Reset the alarm, and then register the label.
LAVEL execution. • Delete the JUMP instruction where an alarm
• The label for jump destination occurred.
does not exist in the job.
4440 UNDEFINED --- Call source job does not exist in the • Reset the alarm, and then execute the
RETURN JOB job call stack. master (start) job.
• Delete the RET instruction.
4441 LACK OF LOCAL --- An error occurred when memory Reset the alarm, and then reduce the number
VARIABLE AREA area for local variable was of local variables to be used.
obtained.
• Memory area is lacking because
too many local variables in the job
are used.
4444 UNSUCCESSFUL --- When PL = 0 or an external servo • Reset the alarm, and then check if external
FINE turned OFF, the number of the force is applied to the manipulator. If
POSITIONING servo error pulses did not fall in the external force is applied to the manipulator,
limit range that had been set in a move the manipulator by the axis operation,
parameter, within the specified etc. to remove the external force. Then, try
time. again.
• If the error occurs again although no
external force is applied to the manipulator,
re-insert the system CPU board correctly.
Data error occurred at job prereading • Reset the alarm, reselect the job, and then
reinterpretation. try again.
1 • The token for prereading Yaskawa representative.
processing could not be obtained.
2 • The prereading processing has

DATA PRESET not been completed within the
4445
ERROR time, and the waiting time for
completion exceeded the limit.
3 • The prereading operation
processing has not been
completed within the time, and
the waiting time for completion
exceeded the limit.
8-80
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
Data error occurred at job prereading • Reset the alarm, reselect the job, and then
reinterpretation. try again.
4 • An error occurred in prereading Yaskawa representative.
DATA PRESET operation process.
4445
ERROR 5 • A_BANK conversion has not been
completed.
255 • An exceptional error occurred in
job execution process.
The variable value exceeded the limit.
0 The variable value exceeded the
limit.
1 The value for the binary (0/1) data
type variable exceeded the limit.
2 The value for the signed 1-byte
data type variable is less than the
minimum value.
3 The value for the unsigned 1-byte
minimum value.
minimum value.
minimum value.
minimum value.
minimum value. Change the variable data type for storage or
OVER VARIABLE
4446 8 The value for the real-number 4- correct the job, so that the variable value is
LIMIT
byte data type variable is less than within the limit.
the minimum value.
data type variable exceeded the
maximum value.
maximum value.
maximum value.
maximum value.
maximum value.
maximum value.
32776 The value for the real-number 4-
byte data type variable exceeded
the maximum value.
8-81
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
The variable value exceeded the limit.
32780 The value for the label-name type
variable exceeded the maximum
value.
32781 The value for the job-name type
variable exceeded the maximum Change the variable data type for storage or
OVER VARIABLE
4446 value. correct the job, so that the variable value is
LIMIT
32782 The value for the character-string within the limit.
type variable exceeded the
maximum value.
32783 The value for comment type
variable exceeded the maximum
value.
4447 DEFECTIVE 0 Incorrect teaching of circular Teach the 3 points again so that they do not
TAUGHT POINT interpolation steps lie in a straight line.
(CIRC) • The three points taught for the
circular interpolation step lie in a
straight line.
8-82
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
An error occurred in weaving control. • Reset the alarm, and then try again.
1 • Weaving control-group If the error occurs again, contact your
designation error Yaskawa representative.
4 • When the speed is specified by Reset the value 0.1 seconds or more.
weaving time in the weaving file,
zero or the negative value is set
for the weaving time.
5 • When the speed is specified by Reset the value 0.1 Hz or more.
frequency in the weaving file, zero
or the negative value is set for the
frequency.
6 • When the timer mode is specified Set a positive value for the timer value.
in the weaving file, a negative
value is set for the timer value.
7 • For triangle or L-type weaving, Set a positive value for the vertical and
zero is set for the vertical or horizontal distance.
horizontal distance.
8 • The coordinate control axis Internal control error. If the error occurs
designation for the reference again, contact your Yaskawa representative.
WEAVING point is different from actual
4448 CONTROL control axis.
ERROR 9 • The distance between the point P
and the TCP could not be
calculated in wrist weaving.
10 • The distance between the point P Set the correct dimensions in the tool data.
and the TCP could not be
calculated in circular wrist
weaving.
11 • The Y-direction element of circular
coordinate system for circular
wrist weaving could not be
calculated.
Contact your Yaskawa representative.
12 • The X-direction element of circular
coordinate system for circular
wrist weaving could not be
calculated.
14 • Weaving basic-orientation • Reset the alarm, and then try again.
calculation error If the error occurs again, contact your
15 • Calculation error of horizontal- Yaskawa representative.
and wall-direction vector for
weaving
4449 UNMATCHED --- The storage destination data Match the position type variable data type for
POSNVAR DATA (pulse/Cartesian) is different from the storage source/destination.
ERROR the storage source data.
An error occurred in tool file number check.
1 An error occurred in tool file • Reset the alarm, reselect the job, and then
4450 FILE NO. ERROR number check. try again.
8-83
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
An error occurred in tool file number check. • Reset the alarm, reselect the job, and then
try again.
2 An error occurred in user Yaskawa representative.
coordinate file number check.
3 An error occurred in calibration file

number check between the
manipulators.
4 An error occurred in tool calibration
file number check.
5 An error occurred in reference point

number check.
6 An error occurred in weaving file

number check.
7 An error occurred in check for

welding start condition file number.
4450 FILE NO. ERROR
welding end condition file number.
9 An error occurred in conveyor

characteristic file number check.
10 An error occurred in press

11 An error occurred in gun

12 An error occurred in conveyor

calibration file number check.
13 An error occurred in argument
number check.

motor gun characteristic file
number.
4451 UNDEFINED --- The reference point (reference Register the reference point.
REFERENCE point number in binary for subcode)
is not registered or is insufficient.
4452 STACK MORE --- An attempt was made to add more Reset the alarm, and then correct the job so
THAN 8 (JOB than eight stacks in the job call that the number of nests for CALL instruction
CALL) stack. is eight or less.
4453 OVER VARIABLE --- The variable number (the variable Correct the job using the variable number
NO. number which an attempt was within the range.
made to use for subcode) is out of
range.
4454 UNDEFINED --- The arc welding characteristic file Complete the settings for the arc welding
WELDER cannot be accessed. characteristic file.
CONDITION FILE • The arc welding characteristic file
is not set.
4455 UNDEFINED ARC --- The welding start condition file Complete the settings for the welding start
START COND cannot be accessed. condition file.
FILE • The welding start condition file is
not set.
4456 UNDEFINED ARC --- The welding end condition file Complete the settings for the welding end
END COND FILE cannot be accessed. condition file.
• The welding end condition file is
not set.
8-84
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
4457 WRONG WELDER --- An error occurred in welder type Correct the reference unit for the welding
SELECTION check. voltage.
• The reference unit for the welding
voltage and the welder type
(independent/unified) do not
match.
4459 EXCESSIVE --- An error occurred in expression Separate the operation expression, shorten
INSTRUCTION operation. the expression, and then register it to a job.
EQUATION • The operation is impossible
because the expression is too
long.
4460 ZERO DEVIDED --- An error occurred in operation Do not divide by zero.
OCCURRENCE instruction.
• Zero division occurred.
4461 UNDEFINED --- An error occurred in automatic Set the number of times of welding release
AUTO WELD welding release conditions. condition, and then try again.
RELEASE COND • The number of welding release
condition is zero for arc auxiliary
file.
4462 UNDEFINED --- An error occurred at arc retry Set the move instruction following ARCON
POSITION FOR execution. instruction.
ARC RETRY • The arc retry has been set, but no
move instruction exists following
ARCON instruction.
4463 PARITY ERROR --- An error occurred in data for user I/ Check the parity data of the user I/O group.
O group.
• The parity check for user I/O
group detected the data error.
4464 OVER BCD --- The BCD value exceeded the limit. • Correct the data.
RANGE • An attempt was made to output a • Correct the data designation (Binary or
value above the maximum value BCD) or parity check designation (with or
that can be expressed in Binary without).
Coded Decimal: 99 (decimal)
when no parity check is specified,
and 79 (decimal) when parity
check is specified.
• An attempt was made to read a
data that cannot be expressed in
Binary Coded Decimal (a data
whose lower or upper 4 bits
exceeded 9 in decimal) in the
variable.
4465 OVER BINARY --- The binary data exceeded the limit. • Correct the data.
RANGE • An attempt was made to output a • Correct the parity check designation.
(PARITY) value that exceeded 127
(decimal) to the user I/O when
parity check was specified.
4466 OFFLINE 0 An undefined command was issued • Reset the alarm, and then try again.
UNDEFINED to the offline position-data If the error occurs again, contact your
COMMAND preparation section. Yaskawa representative.
(ARITH)
4467 USER 0 An error occurred at user Be sure that the number of steps will be three
COORDINATES coordinate creation by a job. or more.
GENERATION • The number of steps was lacking
STEP SHORTAGE for a job for user coordinate
creation.
The calibration data between manipulators
ROBOT could not correctly be prepared.
4468 CALIBRATION 1 • The calibration between The calibration function between
DATA ERROR manipulators cannot be executed manipulators cannot be used for this model.
for this model.
8-85
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
The calibration data between manipulators Set the different groups for the master group
could not correctly be prepared. and the slave group.
2 • The master group and the slave
group are set to the same group.
3 • Incorrect designation of the
control group for master group
control group for slave group
• Reset the alarm, and then try again.
5 • Incorrect designation of the If the error occurs again, contact your
occupation control group for Yaskawa representative.
calibration data
ROBOT
4468 CALIBRATION 6 • Incorrect designation of the
DATA ERROR enabling control group for
calibration data
7 • Among three points in the master-
group’s calibration data, two or
three points are on the same
point.
Teach the different 3 points again.
8 • Among three points in the slave-
group’s calibration data, two or
three points are on the same
point.
9 • The number of the teaching points Teach the specified number of points for the
for calibration data is insufficient. calibration data.
The conversion coordinates for calibration The calibration function between
between manipulators could not be manipulators cannot be used for this model.
prepared.
1 • The calibration between
manipulators cannot be executed
for this model.
ROBOT
4469 CALIBRATION 2 • The master group and the slave Separate the master group and slave group.
FRAME ERROR group are in the same group.
control group for master group • Reset the alarm, and then try again.
4 • Incorrect designation of the If the error occurs again, contact your
control group for slave group Yaskawa representative.
5 • Calibration data setting error
4470 ROBOT 0 An error occurred at calibration Correct the number of steps for a job.
CALIBRATION data creation between
STEP SHORTAGE manipulators.
• The number of steps was lacking
for a job for calibration data
creation between manipulators.
The tool calibration data could not correctly Teach the specified number of points.
be prepared.
1 • Incorrect number of teaching
points for tool calibration
occupation control group for
CALIBRATION calibration data
4471
DATA ERROR
3 • Incorrect designation of the • Reset the alarm, and then try again.
enabling control group for If the error occurs again, contact your
calibration data Yaskawa representative.
control group for calibration data
10 Calibration could not be executed.
8-86
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
4472 TOOL 0 The tool calibration data could not • Reset the alarm, and then try again.
CALIBRATION correctly be prepared. If the error occurs again, contact your
DATA ERROR Calibration could not be executed. Yaskawa representative.
4473 ARITHMETIC 0 The alarm occurred in the • Reset the alarm, and then try again.
ALARM RESET calculation section could not be If the error occurs again, contact your
ERROR reset. Yaskawa representative.
4474 WRONG --- The CALL/JUMP destination job • Make the setting in advance so that the
CONTROL could not be executed. control group of the CALL/JUMP
GROUP AXIS • An attempt was made to call or designation job is included in that of the
jump to a job whose control group CALL/JUMP source job.
cannot be controlled. (Sub code: • Use a PSTART instruction when the
The related control-group) independent control function is used.
4475 CANNOT 0 An attempt was made to execute a Add the robot axis to the control-group of the
EXECUTE JOB job without robot axis. job.
(NO ROBOT) • The robot axis is not designated
for the control-group of the job at
execution of a work instruction
that uses a manipulator.
An attempt was made to change the data for
the job prohibited from being edited.
0 • An attempt was made to change

CANNOT EDIT the tag data.
4476 Release the prohibition.
(EDIT LOCKJOB) 1 • An attempt was made to change
the speed tag data.
2 • An attempt was made to change

the board thickness tag data.
4477 SELECT ERROR --- Incorrect selection of application Needs investigation. Contact your Yaskawa
(APPLICATION) • When executing a work representative.
instruction, the application
selection parameter (parameter
exclusive for manufacturer) is
inconsistent with the application
parameter (AP parameter).
(Subcode: Application number)
4480 SELECT ERROR --- Incorrect selection of sensor Needs investigation. Contact your Yaskawa
(SENSOR) function representative.
• When executing a work
instruction, the sensor application
selection parameter (parameter
exclusive for manufacturer) is
inconsistent with the sensor
parameter (SE parameter).
(Subcode: Sensor number)
4484 WRONG PORT --- Incorrect analog output port Correct the parameter value.
NO. selection parameter
(ANALOG • The value of the parameter
OUTPUT) AxP010 indicating the leading
number of analog output port
used for arc welding or sealing
application was incorrect.
(Subcode: Application number)
4485 WRONG --- When executing a sensor Needs investigation. Contact your Yaskawa
SELECTION instruction, the robot specified to representative.
(SENSOR) use the sensor (system parameter)
and the robot specified to use the
application (system parameter) are
unmatched.
4486 PASS OVER --- When executing COM-ARC • Remove the cause of the path-over.
function, the path was beyond the • Set the path over radius within the allowable
specified path-over monitor zone. range.
8-87
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
4487 WRONG MECH 0 An error occurred in mechanical • Reset the alarm, and then try again.
PARAMETER FILE parameter for the path control If the error occurs again, contact your
section. Yaskawa representative.
4488 PT frame not --- PT frame not completed • This alarm does not occur. (No alarm data
completed is used.)
The CUT instruction could not be executed. Set zero pulse for the C-and W-axis position
1 • The C- and W-axis position at the at the cutting start position.
cutting start position is not zero
DEFECTIVE pulse.
4489 TAUGHT POINT 2 • Zero is set for the cutting radius. Set a value bigger than 0 for the radius.
(CUTTING) 3 • The cutting machine axis is not The CUT instruction can be used for the
mounted. manipulator with small-circle cutting axis only.
4 • This manipulator cannot perform a This robot cannot perform a hexagonal
hexagonal cutting motion. cutting motion. Select an other cutting form.
The Endless motion could not be performed. To perform an interpolation motion such as
1 • After the Endless rotation MOVL and MOVC after an Endless rotation,
completed, an attempt was made execute an MRESET instruction beforehand.
to execute an interpolation
instruction such as MOVL and
MOVC before executing an
MRESET instruction.
DEFECTIVE 2 • The base axis is set as an
4490 TAUGHT POINT Endless rotation axis. The
(ENDLESS) Endless function cannot be used
with the base axis. Change the parameter setting that
designates the Endless rotation axis.
3 • An attempt was made to execute
the Endless function although the
endless axis was not designated.
4 • The Endless axis exceeded the Correct the rotation amount so that the
maximum pulse value Endless axis does not exceed the maximum
(±536870911). pulse value.
An error occurred in the calculation section
for the correcting direction at path correcting
motion.
1 • Control-group designation error
for correcting-direction
preparation
2 • Designation error for the
correcting-direction coordinates
CORRECTIONAL
4491 DIRECTION 3 • When “any direction” is set for the Teach the correcting direction with the
ERROR correcting direction, the correction reference point (REFP).
coordinates is not prepared.
4 • When “any direction” is set for the Teach the reference points (REFP) so that
correcting direction, the reference each point is different.
points (REFP) are taught on the
same point.
5 • Designation error for the • Reset the alarm, and then try again.
coordinated motion control axis at If the error occurs again, contact your
the reference point Yaskawa representative.
8-88
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
An error occurred in the calculation section
for the correcting direction at path correcting
motion.
1 • Data unmatched between the
correction amount data and the
job data:
The information about the control
groups designated for the series
of jobs, which is added to the
POSITION • Reset the alarm, and then try again.
correction amount data, does not
4492 CORRECTION If the error occurs again, contact your
include the valid control-group for
ERROR Yaskawa representative.
the job.
2 • Data unmatched between the
correction amount data and the
job data:
The valid control-group
information that is added to the
correction amount data disagrees
with the valid control-group for the
job.
4493 OVER TOOL FILE --- The tool file number exceeded the • Reset the alarm, and turn the power OFF
NO. limit value. then back ON.
• The tool number for internal If the error occurs again, contact your
control is 25 or more. Yaskawa representative.
4494 DEFECTIVE 1 Incorrect teaching of weaving Change the positions so that the weaving
TAUGHT POINT motion positions start point and end point are different.
(WEAV) • The weaving start point and end
point are on the same point.
4494 DEFECTIVE 2 Incorrect teaching of weaving Change the positions so that the weaving
TAUGHT POINT motion positions start point, end point, and reference point are
(WEAV) • Among the weaving start point, different.
end point, and reference point,
two or three points are on the
same point.
4495 UNDEFINED --- Calibration between manipulators Before using the coordinated motion, execute
ROBOT has not executed. the calibration between manipulators.
CALIBRATION • A coordinated motion is
impossible because no calibration
between manipulators has been
made.
Setting error of motion control parameter
1 • The setting of the manipulator
number is incorrect.
2 • Zero is set for the resolution.
3 • Zero is set in the feedback pulse
parameter.
4 • The setting of L-axis ball-screw
data is incorrect.
5 • The setting of U-axis ball-screw • Set a correct value.
PARAMETER
4496 data is incorrect. If the error occurs again, contact your
ERROR
6 • Zero or a negative value is set for
MAXPPS.
the maximum acceleration speed.
the maximum deceleration speed.
the play-mode servo averaging
time.
8-89
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
10 • The setting of the manipulator
number is incorrect. An
undefined type is designated.
11 • The incorrect coordinate system is • Set a correct value.
designated for the cubic If the error occurs again, contact your
interference. An undefined Yaskawa representative.
coordinate system is set.
12 • The designation of the user
coordinates number is incorrect.
A number out of the setting range
is set.
13 The reduction ratio ≤ 0 is output. • Set a correct value for the resolution.
14 • Zero or a negative value is set for • Set a correct value for the spring constant.
the spring constant. If the error occurs again, contact your
15 • Zero or a negative value is set for • Set a correct value for the motor inertia.
the motor inertia. If the error occurs again, contact your
16 • Zero or a negative value is set for • Set a correct value for the speed calculation
the speed calculation constant. constant.
17 • Dividing number setting error If the error occurs again, contact your
18 • The setting of allowable torque for • Correct the parameter setting.
PARAMETER the speed reducer is incorrect. If the error occurs again, contact your
4496
ERROR Yaskawa representative.
19 • The setting of allowable torque for
the motor is incorrect.
20 • The manipulator type is not Do not use the torque acceleration/
applicable for torque acceleration/ deceleration with this manipulator.
deceleration.
21 • Zero or a negative value is set for • Set a correct value for the balancer.
the balancer. If the error occurs again, contact your
22 • The angle of hexagon set for the • Set a correct value for the angle of
CUT instruction is out of the range hexagon.
"0 degree < angle < 60 degrees." If the error occurs again, contact your
23 • Encoder type designation error
24 • Observer sampling time error If the error occurs again, contact your
25 • Two-degree-of-freedom system Yaskawa representative.
Kp value error
26 • The setting of torque acceleration/ • Correct the parameter setting.
deceleration designation If the error occurs again, contact your
parameter is incorrect. Yaskawa representative.
27 • Observer polarity setting error
28 • The inertia value error for the shift
value calculation
29 • Observer attenuation constant If the error occurs again, contact your
error Yaskawa representative.
30 • Torque estimation parameter error
31 • The segment clock error occurred
when the PV loop is 1 ms.
8-90
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
Setting error of motion control parameter If the error occurs again, contact your
32 • Non-robot axis observer selection Yaskawa representative.
error
33 • Zero is set for the response time • Correct the parameter setting.
constant. If the error occurs again, contact your
34 • Efficiency data error If the error occurs again, contact your
35 • Zero is set for the averaging time • The averaging time constant must be set for
constant. the optimized acceleration/deceleration
control.
• Correct the parameter setting.
36 • Torque limit ratio data error
37 • Coulomb friction data error If the error occurs again, contact your
38 • Kinematic friction coefficient data Yaskawa representative.
error
39 • The setting in the optimized • Correct the parameter setting.
acceleration/deceleration If the error occurs again, contact your
designation parameter is Yaskawa representative.
incorrect.
40 • An uninstalled function is • Correct the parameter setting.
designated. If the error occurs again, contact your
41 • The dynamics-model calculation If the error occurs again, contact your
at the optimized acceleration/ Yaskawa representative.
deceleration is invalid.
42 • Zero is set for the inertia of • Correct the parameter setting.
PARAMETER
4496 dynamics fixed model. If the error occurs again, contact your
ERROR
43 • Designation error for dynamics-
model calculation type
44 • The optimized acceleration/ Yaskawa representative.
deceleration control of speed limit
function is disabled.
45 • The axis designation parameter
for the speed limit function is not
set.
46 • The setting in the mode
designation parameter for the
speed limit function is incorrect.
47 • Zero or negative value is set in the
allowable braking torque
parameter for the speed limit
function.
48 • Zero or a negative value is set in • Correct the parameter setting.
the speed adjustment ratio If the error occurs again, contact your
parameter for the speed limit Yaskawa representative.
function.
49 • Zero or a negative value is set in
the torque limit adjustment ratio
parameter for the acceleration/
deceleration tuning.
50 • Zero or a negative value is set in
the parameter that sets the
shortest acceleration/deceleration
time for when the excessive
torque is applied at the optimized
acceleration/deceleration.
8-91
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
51 • Zero is set for the dimension
information "a3" for the SKR
manipulator.
52 • The setting of sealer-gun control-
group parameter for the servo
sealer control is incorrect. Correct the parameter setting.
53 • The parameter setting for the
Cartesian manipulator X-axis data
is incorrect.
54 • The parameter setting for the
Cartesian manipulator Y-axis data
is incorrect.
55 • The setting for the Dual-arm If the error occurs again, contact your
manipulator is incorrect. Yaskawa representative.
56 • Zero or a negative value is set in Correct the parameter setting.
the FORMCUT maximum
acceleration/deceleration time
parameter.
57 • The setting of expanded check- If the error occurs again, contact your
point designating bits for the arm Yaskawa representative.
interference check is incorrect.
the sphere at the arm interference
check point.
the cylinder at the arm
interference check point.
PARAMETER
4496 62 • The number of designated check
ERROR
points for the arm interference
check is insufficient.
70 • All of X, Y, and Z value of the
expanded check-point 1 for the Correct the parameter setting.
arm interference check are set to
zero.
71 • All of X, Y, and Z value of the
expanded check-point 2 for the
arm interference check are set to
zero.
85 • The setting of wrist axis angle for
tube-incorporated wrist type
manipulators or three-roll wrist
type manipulators is incorrect.
86 • The special link JOG operation Change the parameter setting to disable the
cannot be used with this special link JOG operation for this
manipulator. manipulator.
87 • The setting in the parameter for Correct the parameter setting.
special angle limit check
designation is incorrect.
91 • The setting of the deceleration If the error occurs again, contact your
speed for the path-priority control Yaskawa representative.
is less than zero.
92 • A negative value is set in the
roundness parameter for the
path-priority control. Correct the parameter setting.
93 • The link parameter for the cutting
device is not set.
8-92
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
Setting error of motion control parameter This function cannot be used for control
95 • The real-time bending correction groups other than the robot axis. Correct the
function is enabled for a control- parameter setting.
group other than robot axis.
PARAMETER 96 • Zero is set for the dimension

4496 information "a2" for the Arc Cell Correct the parameter setting.
ERROR
Torch Arm type manipulators.
97 • Zero is set for the deceleration Correct the parameter setting.
ratio for double T-axis unit of the
V-shaped double T-axis
manipulator.
Incorrect teaching points for calibration
between manipulators
1 • Some of the teaching points for
Perform the teaching again so that the
master-group are on the same
teaching points are different from one
point.
another.
2 • Some of the teaching points for
slave-group are on the same
point.
3 • The 2nd-axis positions of C3, C4, Perform the teaching again so that the 2nd-
and C5 of station axes are not the axis positions of C3, C4, and C5 of the
same. station axes are the same.
4 • The 1st-axis positions of C1, C2, Perform the teaching again so that the 1st-
DEFECTIVE
and C3 of station axes are not the axis positions of C1, C2, and C3 of station
4497 TAUGHT POINT
same. axes are the same.
(CALIB)
5 • The 2nd-axis positions of C1, C2, Perform the teaching again so that the 2nd-
and C3 of station axes are the axis positions of C1, C2, and C3 of station
same. axes are not the same.
6 • The 1st-axis rotation direction of Perform the teaching again so that the 1st-
C3, C4, and C5 of station axes axis rotation direction of C3, C4, and C5 of
are not the same. station axes are the same.
7 • The 1st-axis (elevation axis) Perform the teaching again so that the 1st-
positions of C1, C2, and C3 of axis (elevation axis) positions of C1, C2, and
station axes are not the same. C3 of station axes are the same.
8 • The 1st-axis (elevation axis) Perform the teaching again so that the 1st-
positions of C3, C4, and C5 of axis (elevation axis) positions of C3, C4, and
station axes are not the same. C5 of station axes are the same.
4498 CANNOT --- An error occurred in a job without Register the instruction in a job with control
EXECUTE JOB control group. group.
(NO GRP AXIS) • An attempt was made to execute
an instruction that could not be
executed in a job without control
group.
4499 UNDEFINED --- The position type variable is not Set the position type variable.
POSITION registered.
VARIABLE • An attempt was made to use the
position type variable that was not
set. (Subcode: The variable
number)
4500 UNDEFINED --- The user coordinate is not Set the user coordinate.
USER FRAME registered.
• An attempt was made to use the
user coordinate that was not set.
(Subcode: User coordinate
number)
8-93
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
4501 OUT OF RANGE --- The number of tasks exceeded the • Reset the alarm, and then try again.
(PARALLEL limit. If the error occurs again, contact your
PROCESS) • An error occurred in the multi-task Yaskawa representative.
control process for the
independent control function.
(Sub code: Task number)
4502 SL BOARD ON- --- An error occurred in option board at • Remove the option board, and insert it
LINE ERROR power ON. The option board was properly again.
detected not to operate normally at If the error occurs again, contact your
power ON. Yaskawa representative.
4505 UNDEFINED --- Arc retry could not be executed Register a step before the ARCON
POSITION FOR because there was no step before instruction.
ARC ON the ARCON instruction.
4506 UNDEFINED POS --- Arc-restart-return could not be Reset the alarm, and then re-program the
FOR RESTART executed because there was no job.
RETURN restart-return step in the job.
(Example: A retry request was
made while executing a step of the
called job.)
4507 REFP POS --- Incorrect teaching point for search • Perform the teaching again so that the
ERROR (SEARCH detection search start point and the motion target
MOTION) • The search start point and the point are not the same.
motion target point are the same, • Increase the distance between the search
or the distance between the two start point and the motion target point.
points is too short.
8-94
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
An invalid coordinate system was specified.
0 • The specified coordinate system
does not exist.
1 • Designation error of the master
tool coordinate system. This
coordinate system cannot be
used.
2 • Designation error of the tool
coordinate system. This
used.
6 • Designation error of the conveyor
used.
7 • Designation error of the weaving
SPECIFIED used.
Reset the alarm, and then specify a valid
4508 ERROR 8 • Designation error of the COMARC coordinate system.
(COORDINATE) coordinate system. This
used.
10 • Designation error of the cylindrical
used.
11 • Designation error of the
coordinate system for the external
reference point. This coordinate
system cannot be used.
coordinate system for 3D shifting.
This coordinate system cannot be
used.
coordinate system at IMOV for 3D
shifting. This coordinate system
cannot be used.
An invalid coordinate system was specified.
SPECIFIED 16 • Designation error of the H-LINK Reset the alarm, and then specify a valid
4508 ERROR type cylindrical coordinate coordinate system.
(COORDINATE) system. This coordinate system
cannot be used.
4509 MFRAME ERROR 1 An error occurred at MFRAME The master or slave control group is incorrect
execution. when the master tool user coordinate is
specified.
4510 CANNOT --- The SQRT instruction could not be Correct the job.
EXECUTE executed.
INSTRUCTION • An attempt was made to calculate
(SQRT) the square root of negative value.
(The second argument was
negative.)
8-95
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
4511 OUT OF RANGE --- Incorrect robot position when the Reset the alarm, and then try again.
(DROP-VALUE) servo was turned ON
The pulse difference of the robot
position exceeded the allowable
value between when the servo was
OFF previously and when the servo
was ON this time.
The standard allowable number of
pulses is 100. (Subcode: Control
group exceeding the allowable
value.)
4512 TWO STEPS --- The teaching points are aligned in a Perform the teaching again so that the
SAME LINE straight line. teaching points are not aligned in a straight
(3 STEPS) • In the user coordinates for line.
calibration between manipulators,
three or more teaching points are
aligned in a straight line.
4513 EXCESSIVE --- At the safety speed 1, the • Reduce the speed of the step (move
SEGMENT manipulator motion speed instruction) where the alarm occurred.
(SAFETY: 1) exceeded the speed limit value • The manipulator may be near the singular
: LOW (LOW level). point. Change the position and orientation
of the manipulator.
: HIGH (HIGH level). point. Change the position and orientation
of the manipulator.
: LOW (LOW level). point. Change the position and orientation
of the manipulator.
: HIGH (HIGH level). point. Change the position and orientation
of the manipulator.
4517 SEARCH --- An error occurred in search/ Check the system versions for XCP01 and
MONITOR SET monitoring mode settings in servo AXA01.
ERROR (SERVO) section.
• An error occurred in interface with
servo section at search/
monitoring mode. (Subcode: The
related control-group)
4518 SEARCH MON --- An error occurred in search/ Check the system versions for XCP01 and
RELEASE ERROR monitoring mode releasing in servo AXA01.
section.
• An error occurred in interface with
servo section at search/
monitoring mode. (Subcode: The
related control-group)
4519 SPHERE INTRF 1 An error occurred in sphere Perform the calibration between
ERR (ROBOT) interference between manipulators. manipulators.
CALCULATION • No calibration between
manipulators has been made.
4520 AXIS BLOCKING --- A motion was commanded for the Reset the alarm, and then try again. Turn ON
group axis during axis block at play the general-purpose input signal set in the
mode. (Subcode: The related parameter.
control-group)
8-96
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
Job type is inconsistent.
0000_ • A robot job was started from the
0001 concurrent job at CALL/JUMP
WRONG JOB 0000_ • A concurrent job was started from Check that what type of job will be started
4521
TYPE 1001 the robot job at CALL/JUMP before starting.
1000_ • A system job was started from the
0001 robot job at CALL/JUMP
An error occurred at tag data change. • Correct the job file.
2 • An error occurred at instruction If the error occurs again, contact your
TAG DATA
read-in. Yaskawa representative.
CHANGE
4522
PROCESS 3 • The tag is not registered.
ERROR
7 An error occurred at tag data
change.
4524 CANNOT --- An error occurred at concurrent job Correct the job.
EXECUTE INST execution.
(CONCUR JOB) • There was an unexecutable
instruction such as move
instruction in the concurrent job.
4525 SPECIFIED JOB --- An error occurred at startup of Needs investigation. Contact your Yaskawa
EXECUTION multi-system job. representative.
IMPOSSIBILITY • The specified job could not be
executed.
4527 UNDEFINED --- Incorrect analog output port Correct the specified analog output port
PORT NO. (AOUT) number number.
• The specified analog output port
number was not allowed.
4528 SYNTAX ERROR --- An error occurred in the instruction • Needs investigation. Contact your Yaskawa
syntax. representative.
• The function and the • If replacement of the system software is
corresponding instruction data is necessary, follow the instructions for
inconsistent in the system replacement. After replacement, delete the
software. (Subcode: Box number) corresponding instructions, and then re-
register them.
An error occurred at twin synchronization
execution.
TWIN
1 • A job without control group was
4529 COORDINATED
started by SYNC instruction. Specify a R□+S□ job for the job started by
ERROR
2 • A job only with robot axes was SYNC instruction.
started by SYNC instruction.
An error occurred at twin synchronization
execution.
Specify a R□+S□ job for the job started by
3 • A job only with master control
SYNC instruction.
group axes was started by SYNC
instruction.
4 • At full synchronization, the • Correct the job.
completion timings of move If the error occurs again, contact your
TWIN
instructions for the master and the Yaskawa representative.
4529 COORDINATED
slave disagreed.
ERROR
5 • At full synchronization, no
operation request from the master
was sent.
6 • At full synchronization, the • Correct the job.
execution timings of move If the error occurs again, contact your
instructions for the master and the Yaskawa representative.
slave disagreed.
8-97
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
An error occurred in conveyor • Reset the alarm, and then try again.
synchronization execution. If the error occurs again, contact your
1 • The base axis specification is
other than 1 or 2 for conveyor
characteristic file.
2 • No robot axis in the job for robot
axis tracking
CONVEYOR 3 • No base axis in the job for base
4530 SYNCHRONIZING axis tracking
ERROR
4 • The conveyor board number and
conveyor characteristic file
number used are incorrect.
5 • There was no conveyor start
position data at prereading
processing.
10 • No base axis in the job for arc
tracking
4531 CONVEYOR --- Conveyor characteristic file is not Set "Use state" of conveyor characteristic file
CHARACTERISTI set. set for the job to "1: Use".
C FILE UNSET • "Use state" of the conveyor
characteristic file set for the job is
not set to "1: Use". (Subcode:
Conveyor characteristic file
number)
4532 CONVEYOR --- The conveyor speed decreased Correct the "Conveyor Lowest Speed" set in
SPEED DOWN below the "Conveyor Lowest the conveyor characteristic file.
Speed" set in the conveyor
characteristic file. (conveyor
number for subcode)
An internal control error occurred at
conveyor tracking motion.
1 • Designation error of the conveyor
tracking control-group
2 • Designation error of the user • Reset the alarm, and then try again.
CONVEYOR If the error occurs again, contact your
coordinates for the conveyor
TRACKING Yaskawa representative.
4533 tracking
CALCULATION
ERROR 3 • An attempt was made to use the
conveyor tracking function with
the slave manipulator at
coordinate motion.
4 • Zero is set for the resolution for Set a correct value for the resolution.
the turn-table synchronization.
4534 TORQUE --- Excessive interference torque • Check if the weight information in the tool
INTERFERENCE • The load torque of an axis motor file is correctly set.
exceeded the allowable value • Reduce the speed in the step where the
when the manipulator is operating alarm occurred.
at the specified speed. • Change the position and orientation in the
step where the alarm occurred.
An error occurred at PSEND instruction
execution.
4535 PSEND ERROR 1 • An attempt was made to send a Check the destination address.
mail to its own task.
3 • The mail box number is incorrect.
8-98
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
An error occurred at PRECV instruction
execution.
1 • An attempt was made to receive a
4536 PRECV ERROR mail from its own task. Check the destination address.
2 • The mail data type is inconsistent.

3 • The mail box number is incorrect.
An error occurred in mail box control in the • Reset the alarm, and then try again.
offline processing section. If the error occurs again, contact your
OFFLINEMAIL
1 • Mail box number error Yaskawa representative.
BOX
4537
PROCESSING 2 • Undefined command for mail box
ERROR operation
3 • OFF_MB_IFS pointer is incorrect.
4538 ROBOT AXIS --- The robot axis tracking could not be Correct the job.
TRACKING executed.
IMPOSIBILITY • An attempt was made to execute
the SYMOVJ instruction at robot
tracking.
An internal control error occurred at the
Corner-R motion. Do not use the Corner-R motion for
1 • The Corner-R motion cannot be coordinated motion.
used for coordinated motion.
2 • An attempt was made to execute Perform the teaching again so that the start
the Corner-R motion for the same step and end step are not on the same point.
point.
3 • The Corner-R zone is taught on a Perform the teaching again so that the
straight line. Corner-R zone is not on a strait line.
4 • The start position or end position • Change the setting for the Corner-R radius.
for the Corner-R motion could not • Perform the teaching again for the start step
be calculated inside the start zone or end step for Corner-R.
or the end zone.
CORNER R
4539 CONTROL 5 • The Corner-R motion cannot be Do not use the Corner-R motion for master
ERROR used for coordinated motion (with manipulators at coordinated motion.
master manipulators).
6 • The Corner-R motion cannot be Use a MOVL instruction when using the
used for MOVC, MOVS, and Corner-R motion.
EIMOVC instructions.
7 • The Corner-R motion is disabled Do not perform weaving when using the
during weaving. Corner-R motion.
8 • Different tool numbers are set in a Use the same tool number in a Corner-R
Corner-R zone (for the Corner-R zone.
middle step and end step).
9 • The Corner-R motion is disabled Disable the higher-order acceleration/
when the higher-order deceleration when using the Corner-R
acceleration/deceleration is motion.
specified.
An internal control error occurred at the Do not perform the conveyor tracking when
CORNER R Corner-R motion. using the Corner-R motion.
4539 CONTROL
ERROR 17 • The Corner-R motion is disabled
during conveyor tracking.
4540 JOB QUE EMPTY --- No job queue data Set a data to a job queue, and then call
ERROR • "QUE" is used in CALL or JUMP "QUE".
instruction under the condition
that no job queue is used.
8-99
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
4541 INVALID INPUT --- An error occurred at VAL instruction Check the data of character string of
STRING (VAL) execution. conversion source.
• An attempt was made to convert a
character string that could not be
converted to a numerical value.
4542 MRESET ERROR 1 An error occurred at MRESET • Reset the alarm, and then try again.
instruction execution. If the error occurs again, contact your
• An MRESET instruction was Yaskawa representative.
executed while no endless axis
was designated.
4543 JOB CALL STACK --- An error occurred at job return. • Reset the alarm, and then try again.
ERROR • At job return, an attempt was If the error occurs again, contact your
made to fetch a data from an Yaskawa representative.
empty job call stack or to stack a
data in the job call stack that is
full.
MID$ ERROR An error occurred at MID$ instruction Check the data of the character string to be
execution. extracted.
1 • The first character of character
string to be extracted is null at
4544 MID$ instruction execution.
2 • The extraction start position Check the extraction start position or the data
exceeds the character string of the character string to be extracted.
length at MID$ instruction
execution.
4545 COMMUNICATION --- An error occurred at OPEN/CLOSE • Reset the alarm, and then try again.
SERVICE ERROR instruction execution. If the error occurs again, contact your
• An error occurred in the Yaskawa representative.
communication service at OPEN/
CLOSE instruction execution.
4546 CANNOT --- The system job could not be • Reset the alarm, and then try again.
EXECUTE executed. If the error occurs again, contact your
SYSTEM JOB • An error in the system number of Yaskawa representative.
system job. (Subcode: System
number)
4547 PRIMITIVE --- A primitive error occurred in the • Reset the alarm, and then try again.
ERROR system software. (Subcode: Error If the error occurs again, contact your
code) Yaskawa representative.
4548 CANNOT --- An error occurred at INIEVNT • Reset the alarm, and then try again.
OPERATE instruction execution. If the error occurs again, contact your
SPECIFIED • The specified event could not be Yaskawa representative.
EVENT QUE operated at INIEVNT instruction
execution.
4549 INIEVNT NOT --- An error occurred at INIEVNT Execute an INIEVNT instruction.
EXECUTED instruction execution.
• INIEVNT instruction was not
executed before having executed
the event related process.
(Subcode: System number)
4550 CANNOT --- The specified instruction in the user Correct the job.
EXECUTE INST job could not be executed.
(USER JOB) (Subcode: System number)
4551 CANNOT --- The electrode installation correction Execute "SVGUNCL TWC-AE" before
MEASURE TIP value could not be measured on the executing "SVGUNCL TWC=BE."
INSTALL COEF moving side because that on the
fixed side was not measured during
execution of "SVGUNCL
TWC=BE."
8-100
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
The used function and the system are • Reset the alarm, and then try again.
inconsistent. If the error occurs again, contact your
1 • The multi-layer welding function is Yaskawa representative.
not used.
2 • The observer function is not used.
3 • The TURBO function is not used.
4 • The COMARC function is not
used.
5 • The conveyor/press
synchronization function is not
used.
6 • The shared motion function is not
used.
7 • The layer motion function is not
used.
8 • The general sensor function is not
used.
9 • The servo float function is not
SOFTWARE used.
4565
UNMATCH 10 • The laser cutting function (with
small circle cutter) is not used.
11 • The motor gun function (for spot

welding application) is not used.
12 • The speed control function
(VCON/VCOF) is not used.
13 • The servo hand function (for
handling application) is not used.
14 • The laser cutting function (for form
cutting operation) is not used.
15 • The series communication
function between the systems
(PSEND/PRECV) is not used.
16 • The motion extension function is
not used.
17 • The bending function is not used.
18 • The ME-NET function is not used.
255 • An attempt was made to execute
an undefined instruction.
An internal control error occurred at
USER preparation of a user coordinates.
COORDINATES Perform the teaching again for the user
4566 1 • The teaching points are incorrect.
GENERATION coordinates.
ERROR 2 • The teaching points for user-
coordinate turning are incorrect.
3 An internal control error occurred at
preparation of a user coordinates.
USER • The robot axis is not specified for
the control group of the job to • Reset the alarm, and then try again.
COORDINATES
4566 prepare the user coordinates. If the error occurs again, contact your
GENERATION
ERROR 5 • Position data error
6 • Setting error of the slave group for
user coordinate conversion
8-101
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
4567 CANNOT --- The distance could not be Do not perform the arc retry or restart
MONITOR monitored when executing a move operation, or change the interpolation
DISTANCE instruction. instruction to MOVL/MOVC.
• An attempt was made to execute
MOVJ/MOVS instruction in arc
retry or restart operation.
4568 UNDEFINED --- No press characteristic file is set. Set the status of press characteristic file to be
PRESS • An attempt was made to use the used in the job to "Used State".
CHARACTERISTI unused press characteristic file in
C FILE a job. (Subcode: Press
characteristic file number)
4569 PRESS --- No press resolution data is set. Set the data, and then press "Data Set"
RESOLUTION • The status of press resolution button to set the status to "Completed".
DATA UNSET data to be used in the job was set
to "Incomplete". (Subcode: Press
characteristic file)
4571 SERVO FLOAT --- The servo float mode could not be • Check the ROM version of servo board.
MODE RELEASE reset when executing a FLOATOF • Reset the alarm, and then try again.
ERROR instruction. If the error occurs again, contact your
4572 UNDEFINED --- The control group for the motor gun Restart the setting of configuration in
MOTOR GUN is not set. maintenance mode, and correct the setting of
CONTROL GRP motor gun axis.
4573 SPOT WELDER --- Incorrect spot welder number Correct the welder number set in the gun
NUMBER ERROR • The welder number set in the gun characteristic file.
characteristic file is incorrect.
(Subcode: Welder number)
4574 SPOT WELD --- The spot welding did not complete • Remove the cause such as disconnection of
COMPLETE TIME within the specified time. power supply to the timer conductor, and
LIMIT • Neither the welding completion then try again.
signal nor the welding error signal • If the response from the timer takes too long
was received from the timer time due to the system layout, increase the
conductor within the set time. set time.
4575 ERROR IN WELD --- Incorrect setting of spot welding Set the 2nd pressure, or change the start
START TIMING start timing timing.
SET • For motor gun, the welding timing
was set to "After First Pressure"
while no 2nd pressure was set.
4576 ERR IN MOTOR --- An error occurred when setting the • Check the ROM version of servo board.
GUN CONT MODE motor gun control mode. • Reset the alarm, and then try again.
• Though a motor gun control mode If the error occurs again, contact your
setting command was sent to the Yaskawa representative.
servo section, no response was
received.
4577 ERR IN MOTOR --- An error occurred when resetting • Check the ROM version of servo board.
GUN MODE RLSE the motor gun control mode. • Reset the alarm, and then try again.
• Though a motor gun control mode If the error occurs again, contact your
resetting command was sent to Yaskawa representative.
the servo section, no response
was received.
4578 SPOT WELD --- An error occurred when executing Reset the timer conductor where the welding
ERROR spot welding. error occurred, and then try again.
• An error occurred when executing
welding using the specified
system timer conductor.
8-102
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
An error occurred in the anticipation control
processing.
ANTICIPATION
1 • No availability in anticipation Register a move instruction between work
4579 CONTROL
control instructions.
ERROR
2 • The anticipation data exceeded
the maximum length.
4580 ANTICIPATION --- Anticipation could not be executed • Reset the alarm, and then try again.
DISTANCE at re-painting. • Refer to "Painting System Additional
SHORTAGE • No return step in re-painting Function Manual" for details.
function after emergency stop
An error occurred in the anticipation output
file.
DEFECTIVE
1 • Incorrect setting of OT output
4581 ANTICIPATION
number for anticipation output file Reset the alarm, and then correct the set
FILE
2 • Incorrect setting of OG output number.
number for anticipation output file
4583 CANNOT --- An invalid gun type is set. Change the motion mode set to the gun.
EXECUTE GUN • The mode impossible to control is
TYPE set for the gun.
4584 STRWAIT TIME --- An error occurred when executing a • Remove the cause such as defective limit
OUT STRWAIT instruction. switch, and then try again.
• No confirmation signal specified in It the error occurs again, contact your
the stroke change confirmation Yaskawa representative.
instruction was input within the
set time.
4585 SERVO PART PG --- The PG power supply could not be Check the cable connection of motor gun
POWER ON turned ON. encoder.
ERROR • The encoder power supply could
not be turned ON when turning
ON the control power supply.
An error occurred when changing the gun. Check the cable connection of motor gun
1 • A GUNCHG instruction was encoder.
executed in the system
configuration that did not allow
the gun change function.
2 • A GUNCHG/PICK instruction was Execute GUNCHG/PICK instruction when the
executed while the motor gun motor gun motor is servo OFF.
motor was servo ON.
3 • A GUNCHG/PICK instruction was
executed while the ATC was in
MOTOR GUN
4587 unchuck status. Execute GUNCHG/PICK instruction when the
CHANGE ERROR
4 • A GUNCHG/PLACE instruction ATC is in chuck status.
was executed while the ATC was
in unchuck status.
5 • The encoder power supply could
not be turned ON when executing
a GUNCHG/PICK instruction.
Check the cable connection of motor gun
6 • The encoder power supply could encoder.
not be turned OFF when
executing a GUNCHG/PLACE
instruction.
7 • The gun number specified by the • Check the gun characteristic file number
GUNCHG instruction did not specified by GUNCHG instruction.
agree with the gun identification • Check the status of gun identification signal.
MOTOR GUN signal.
4587
CHANGE ERROR
8 • The 1st gun axis selection signal Check the 1st gun axis selection signal
is not set when executing the setting.
twin-wrist gun change.
8-103
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
An error occurred when changing the gun. Check the setting for the gun axis selection
9 • The right and left gun axis signal.
MOTOR GUN
4587 selection signals were duplicated
CHANGE ERROR
when executing the twin-wrist gun
change.
4591 SERVO PART --- An error occurred at speed control • Check the ROM version of servo board.
SPEED CONTROL mode setting. • Reset the alarm, and then try again.
MODE SETTING • Though a speed control mode If the error occurs again, contact your
ERROR setting command was sent to the Yaskawa representative.
servo section, but no response
was received.
4592 SERVO PART --- An error occurred at speed control • Check the ROM version of servo board.
SPEED CONTROL mode release. • Reset the alarm, and then try again.
MODE RELEASE • Though a speed control mode If the error occurs again, contact your
ERROR release command was sent to the Yaskawa representative.
servo section, but no response
was received.
4593 SERVO HAND --- An error occurred at servo hand • Check the ROM version of servo board.
CONTROL MODE control mode setting. • Reset the alarm, and then try again.
SETTING ERROR • Though a servo hand control If the error occurs again, contact your
mode setting command was sent Yaskawa representative.
to the servo section, but no
response was received.
4594 SERVO HAND --- An error occurred at servo hand • Check the ROM version of servo board.
CONTROL MODE control mode setting. • Reset the alarm, and then try again.
RELEASE ERROR • Though a servo hand control If the error occurs again, contact your
mode release command was sent Yaskawa representative.
to the servo section, but no
response was received.
An internal control error occurred in the Form Correct the radius data.
Cutting motion.
1 The setting for radius is incorrect.
• For a circle, it is incorrectly set as:
radius ≤ 0, radius < minimum
radius value, or radius >
maximum radius value.
• For an ellipse, it is incorrectly set
FORM CUTTING as: radius ≤ 0, radius < minimum
4595 MOTION radius value/2, or radius >
IMPOSSIBILITY (maximum radius/2 − width/2).
2 The setting for width is incorrect. Correct the width data.
• For a rectangle, it is incorrectly set
as: width < 1.0, width > sqrt
(maximum diameter 2 − height2),
or width > maximum diameter.
• It is incorrectly set as: width < 0,
width > maximum diameter −2 ×
radius.
8-104
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
An internal control error occurred in the Form Correct the height data.
Cutting motion.
3 The setting for height is incorrect.
as: height > maximum diameter,
height < minimum diameter/2, or
height > sqrt (maximum diameter2
− width2).
4 The setting for the corner radius is Correct the corner radius data.
incorrect.
as: corner radius > width/2 or
corner radius > height/2.
5 The setting for overlap is incorrect. Correct the overlap data.
as overlap > width/2.
• For a circle, it is incorrectly set as
overlap > ABS (2π × radius).
• For an ellipse, it is incorrectly set
as overlap > π × radius +ABS
(width/2).
6 The setting for the cutting speed is Correct the cutting speed data.
incorrect. It is set as the cutting
speed > maximum linear speed.
7 • Coordinated motion cannot be Do not use the coordinated motion.
used with the Form Cutting
motion.
FORM CUTTING 8 • Zero or a negative value is set in Correct the setting of the minimum diameter
4595 MOTION the minimum diameter parameter parameter (S1CxG063) for the Form Cutting
IMPOSSIBILITY (S1CxG063) for the Form Cutting motion.
motion.
9 • Zero or a negative value is set in Correct the setting of the maximum diameter
the maximum diameter parameter parameter (S1CxG064) for the Form Cutting
(S1CxG064) for the Form Cutting motion.
motion.
10 • Although "PLACEMENT" or Execute the FORMAPR instruction.
"AUTO" is set for the start point
designation on the FORM CUT
SETTING window, the
FORMAPR instruction was not
executed.
11 • The Cut file setting of the The Cut file settings of FORMAPR and
FORMAPR instruction is different FORMCUT instructions must be same.
from that of the FORMCUT
instruction.
12 • A FORMAPR instruction was The FORMAPR instruction cannot be used
used for the conventional for the conventional FORMCUT instruction.
FORMCUT instruction. • Change the instruction.
• Needs to validate the new FORMCUT
instruction. Contact your Yaskawa
representative.
13 • A form other than a circle, A form other than a circle, rectangle, and
rectangle, and ellipse was ellipse cannot be designated for the
designated for the conventional conventional FORMCUT instruction.
FORMCUT instruction. • Designate a circle, rectangle, or ellipse.
• Needs to validate the new FORMCUT
instruction. Contact your Yaskawa
representative.
8-105
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
An internal control error occurred in the Form • Correct the radius data.
Cutting motion.
90 • The radius data setting for special
circular interpolation is incorrect.
It is incorrectly set as the radius ≤
0.
91 • The arc center coordinates could
not be calculated at special
circular interpolation. Incorrect
teaching may be the cause.
Perform the teaching again.
92 • The arc center coordinates could
not be calculated at special
FORM CUTTING circular interpolation. Incorrect
4595 MOTION teaching may be the cause.
IMPOSSIBILITY 93 • The averaging time at special • Perform the teaching again so that the
circular interpolation motion is too moving distance becomes longer.
short. • Reduce the motion speed.
94 • Because the designated plane Perform the teaching again for the reference
included reference points at point 2.
special circular interpolation
motion, the arc center coordinates
could not be calculated. Incorrect
teaching of the reference point 2
may be the cause.
100 • The arc center position is not set Perform the teaching for the reference point 1
for the special circular as the arc center position.
interpolation motion.
1 An error occurred at FORMCUT
FORMCUT • Perform the teaching for the reference point
4596 An attempt was made to re-execute
ERROR 1 as the arc center position.
the FORMCUT instruction after
interrupting it.
An internal control error occurred at offline
position data conversion.
1 • Incorrect information of reference
position data for offline position
data conversion
2 • Incorrect user-coordinate number
designation in the standard
position data for offline position
data conversion
3 • Incorrect reference-point data for
OFFLINE offline position data conversion
POSITION DATA 4 • The standard position data for
CONVERSION offline position data conversion Yaskawa representative.
ERROR could not correctly be calculated.
5 • Incorrect pulse incremental value
for offline position data
conversion
6 • The position data could not
correctly be added by the pulse
incremental value at the offline
7 • Incorrect Cartesian incremental
value for offline position data
conversion
8-106
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
An internal control error occurred at offline
correctly be added by the
Cartesian incremental value at
the offline position data
conversion.
9 • The position conversion could not
be done in the designated
coordinate system at the offline
10 • Incorrect incremental value of
angle for offline position data
conversion
correctly be added by the
incremental value of angle at the
offline position data conversion.
12 • The reverse shift value for 3D
shifting could not correctly be
calculated at the offline position
data conversion.
13 • The reverse shift value for 3D
shifting could not correctly be
added at the offline position data
conversion.
14 • The reverse shift value could not
OFFLINE correctly be calculated at the • Reset the alarm, and then try again.
POSITION DATA offline position data conversion.
CONVERSION
15 • The reverse shift value could not Yaskawa representative.
ERROR
correctly be calculated at the
16 • The 3D shifting value could not
correctly be added at the offline
17 • The shift value could not correctly
be added at the offline position
data conversion.
18 • No reference point is specified for
the offline position data
conversion.
19 • The positions for the mirror shift
function could not correctly be
calculated at the offline position
data conversion.
20 • The positions could not correctly
be converted for the mirror shift
function at the offline position data
conversion.
21 • The expansion positions for the
mirror shift function could not
correctly be converted at the
22 • Incorrect designation of
coordinates for a new mirror-shift
conversion function at the offline
position data conversion
8-107
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
4599 SERVO 0 An abnormal response was • Reset the alarm, and then try again.
COMMAND returned from the servo control • Turn the power OFF then back ON.
ERROR section. If the error occurs again, contact your
The servo control processing has Yaskawa representative.
not completed.
4601 UNDEFINED GUN --- The motor gun characteristic file is Complete the settings for the motor gun
COND FILE not set. (Subcode: Motor gun characteristic file.
4603 WIRE STICKING --- Wire stick occurred at spot welding. Remove the cause of wire stick.
• Wire stick was detected at the
welder. (Subcode: Welder
number)
4604 DESIGNATED --- No home position correction data of • Reset the alarm, and then try again.
AXIS HOME specified axis If the error occurs again, contact your
POSITION Yaskawa representative.
CORRECTION
DATA NON-
EXISTING
4605 SETTOOL ERROR --- An error occurred when executing a • Check if the tag set value is correct.
SETTOOL instruction. • Check if the parameter is set correctly.
• The difference between the
current tool constant and a new
set value exceeded the allowable
range (parameter set value).
4606 GLOBAL --- The memory area of global variable Correct the number of global (user) variables
VARIABLE AREA exceeded the limit value. to be used, or correct the parameter value.
OVERFLOW • An error occurred in the value of
parameter that defines the
number of global (user) variables.
An error occurred when executing a macro
instruction.
1 • The execution macro job is not Correct the registration of interrupt macro job.
set.
2 • The interrupt macro job is not set.
MACRO
COMMAND 3 • An attempt was made to start the Correct the macro job.
4607 job that could not be started by
EXECUTION
ERROR the macro instruction.
5 • An error occurred in the operation • Reset the alarm, and then try again.
process of job call stack when the • Turn the power OFF then back ON.
execution of macro instruction If the error occurs again, contact your
was cancelled. Yaskawa representative.
6 • Incorrect macro number
An error occurred when executing a
GETARG instruction.
1 • The job argument is not set.
JOB ARGUMENT
4608 2 • No number of the specified job Correct the job.
GET ERROR
argument
3 • The data types of job argument
disagreed.
8-108
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
An error occurred when executing the memo
play operation.
2 • The memory play file was being
used in another system.
MEMORY PLAY 5 • The control group in the memory

4609 play file did not agree with the Correct the job.
FILE ERROR
control group of execution job.
6 • An attempt was made to clear the
memory play file by a CLEAR
instruction before having
executed a MEMOF instruction.
An internal control error occurred at memory
play sampling.
1 • Failed to read the memory play
sampling data. • Reset the alarm, and then try again.
2 • Failed to write the memory play Yaskawa representative.
MEMORY PLAY sampling data.
4610 SAMPLING 3 • Failed to seek the memory play
ERROR sampling data.
4 • Incorrect mode setting at memory Correctly set the memory play mode.
play sampling
5 • Incorrect designation of the • Reset the alarm, and then try again.
control group at memory play If the error occurs again, contact your
sampling Yaskawa representative.
An internal control error occurred at memory
play sampling.
6 • K/N < 0 in the memory play
MEMORY PLAY sampling section • Reset the alarm, and then try again.
4610 SAMPLING 7 • The memory play sampling data If the error occurs again, contact your
ERROR back-play mode could not be Yaskawa representative.
detected.
8 • The memory play sampling data
could not be initialized.
4611 OPTON --- An error occurred when executing a Correct the OPTON instruction.
INSTRUCTION OPTON instruction.
EXECUTION • The number of times that the
NUMBER OVER OPTON instruction was executed
exceeded the limit value.
4612 TSYNC ERROR --- An error occurred at the execution Set the same number of synchronizations of
of the TSYNC instruction. the TSYNC instruction.
• The number of synchronizations
(SNUM) specified by the TSYNC
instruction disagreed. (Sub code:
the number of synchronizations of
the first executed TSYNC)
8-109
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
An internal control error occurred in the
servo sealer gun motion. • Set the function designation parameter.
1 • The function designation Yaskawa representative.
parameter is not set.
2 • No sealer gun axis exists at the
job for which the sealer gun
control was attempted to be • Correct the job.
executed. If the error occurs again, contact your
3 • No robot axis exists at the job at Yaskawa representative.
SERVO SEALER
which an attempt was made to
4613 GUN CONTROL
execute sealer gun control.
ERROR
4 • Incorrect designation of the Set either "1" or "2" for PRM1 control method
control method for sealer gun designation of the OPTON instruction.
control
5 • Incorrect designation of the If "1" is set for PRM1 of the OPTON
needle position for sealer gun instruction, set the PRM2 needle position
control designation to a value between 0 and 100.
6 • Incorrect designation of the If "2" is set for PRM1 of the OPTON
sealing width for sealer gun instruction, set PRM2 sealing width
control designation to a value between 0 and 30.
4614 SEALER GUN 0 The servo sealer gun condition file Set the servo sealer gun condition file.
CHARACTERISTI is not set.
C FILE UNSET
4615 I/O AXIS MOTION 0 I/O axis motion could not be • Stop the I/O axis motion.
IMPOSSIBILITY performed. (in playback) • Correct the job.
(during playback) • An attempt was made to
command a job whose control
group was in I/O axis motion.
An internal control error occurred when
shifting the axis. • Reset the alarm, and then try again.
AXIS SHIFT
4616 1 • The file could not be switched If the error occurs again, contact your
ERROR
because of incorrect start point Yaskawa representative.
designation.
An internal control error occurred when
shifting the axis.
2 • The control group with which the
axis shifting is performed
disagrees with the control group
set for the axis shifting function in
the calibration file. • Reset the alarm, and then try again.
AXIS SHIFT
ERROR 3 • The calibration file number for axis Yaskawa representative.
shifting function is out of the
applicable range.
4 • There is no "selected" file
corresponding to the calibration
file number for the axis shift
function.
SU-axes cannot move with the current L- • Reduce the speed of S- and U-axes.
and R-axes position. • Teach the positions of L- and R-axes again
1 • For the CSL15D manipulator, the so that S- and U-axes can move.
SU AXIS MOTION
motion speed of S- and U-axes
DISABLED
exceeded the upper limit.
4617 (LR AXIS
POSITION 2 • For the CSL15D manipulator, S-
ERROR) and U-axes were going to move
regardless of the limit speed "0"
when the positions of L- and R-
axes exceeded the upper limit.
8-110
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
4618 SHIFT 1 An internal control error occurred at Set the shift value for Y-axis only.
INSTRUCTION execution of the SHIFT instruction.
EXECUTION • For the tool shift with Euler angle
ERROR ±90 degrees, the shift value for
axes other than Y-axis is set.
4619 UNDEFINED JOB --- An error occurred in job registration Set the job registration table.
ENTRY TABLE table.
• The job registration table is not
set. (Subcode: Designated
registration number)
4620 ARM (TOOL) 0 Arms or tools interfere between Perform the teaching again to correct
INTERFERENCE manipulators. positions for manipulators.
• The arm interference check
between manipulators detected
that manipulator’s arms or tools
are interfered.
4621 WELD COMPLETE --- An error occurred in welding Check the settings for welding completion
SIGNAL ERROR completion signal. signal.
• The welding completion signal
was ON when starting the spot
welding instruction execution.
4622 SELF 0 The manipulator’s arm interferes Perform the teaching again to correct
INTERFERENCE with a tool. positions for manipulators.
• The manipulator’s self
interference check detected that
the manipulator’s arm interferes
with a tool.
GETPOS An error occurred when executing a
COMMAND GETPOS instruction.
ERROR 1 • An attempt was made to obtain
4623 the step that used a local position Correct the GETPOS instruction.
type variable. (The step with local
position type variable cannot be
fetched. Example: MOVJ LP000
VJ=25.00)
GETPOS An error occurred when executing a
COMMAND GETPOS instruction.
ERROR 2 • An attempt was made to obtain
the step that used an array
4623 position type variable. (The step Correct the GETPOS instruction.
with array position type variable
cannot be fetched. Example:
MOVJ P[0] VJ=25.00)
3 • The specified step did not exist.
4624 PLUG VOLUME --- Incorrect setting of amount of Review the setting for the amount of fillings.
SETTING ERROR fillings
8-111
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
WRONG An error occurred when executing a • Reset the alarm, and then try again.
EXECUTION OF LOADDB instruction. If the error occurs again, contact your
LOADDB INST 1 • No file Yaskawa representative.
2 • No directory
4 • There was no directory entry after
this point.
-1 • No file name
-2 • File presence error
-3 • Incorrect file name
-4 • The disk is full.
-5 • The directory is full.
-6 • I/O error
-7 • Invalid handle
-8 • Handle overflow
-9 • File has already been opened.
-10 • File attribute error
-11 • Open mode error
-12 • The hardware disk with large
capacity is used.
4625 -14 • The door is open.
-15 • The disk is write-protected.
-30 • Card controller access error
-31 • No card
-32 • Card drive information readout
error
-33 • Partition table error
-34 • No drive number
-35 • No specified partition number
-36 • Cluster size error
-37 • Incorrect number of sectors
-38 • Sector/byte error
-40 • Card not applicable for I/O
-41 • Nonsupported version
-42 • The setting register did not exist.
-43 • Card not applicable for ATA
-44 • Double chain error
-45 • Media error (not fixed disk)
-50 • Media error (not fixed disk)
WRONG An error occurred when executing a • Reset the alarm, and then try again.
EXECUTION OF LOADDB instruction. If the error occurs again, contact your
4625 LOADDB INST Yaskawa representative.
-51 • Sector read command error
-52 • Sector write command error
4626 IMPOSSIBLE S- --- An error occurred at S-axis high- Correct the limit distance for S-axis rotation
AXIS MOV speed rotation. center motion (S1CG067).
(IN SPHERE) • The S-axis rotation radius was
below the lower limit.
4627 GUN --- The gun identification signal was Check the gun identification signal.
RECOGNITION not received. (Subcode: Gun
SINGLE OFF number)
8-112
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
4628 WRITE --- An error in the variable number Correct the written destination variable
VARIABLE NO. setting. numbers.
MULTI SETTING • Duplicated usage of the written
destination variable numbers.
(Subcode: Duplicated variable
number)
GROUP CHANGE An error occurred when executing the group Validate the group change parameter.
ERROR change function.
1 • The group change parameter was
invalid.
2 • The GRPCHG instruction was Execute the GRPCHG instruction when the
executed while the external axis external axis motor was servo OFF.
motor was servo ON.
3 • The GRPCHG instruction was Execute the GRPCHG instruction in chuck
executed in unchuck status. status.
4 • The group identification signal Check the group identification signal.
was not received.
5 • The specified control group Check the specified control group number.
4629 number and the group
identification number were
unmatched.
6 • The encoder PG power supply Turn ON the encoder PG power supply when
was OFF when the GRPCHG was GRPCHG is ON.
ON.
7 • The encoder PG power supply
Turn OFF the encoder PG power supply
was ON when the GRPCHG was
when GRPCHG is OFF.
OFF.
8 • The control group that Check the group identification signal.
corresponded to the received
group identification signal did not
exist.
4630 DUPLICATED --- The gun numbers were overlapped Check the gun numbers.
GUN NUMBER when executing a SVSPOT
instruction. (Subcode: The
overlapped gun number)
4632 UNDEFINED LNR --- The linear scale characteristic file is Set the linear scale characteristic file.
SCALE FILE not set. (Subcode: Linear scale
4633 FOLLOWING 1 An error occurred when executing a Re-execute the move instruction executed
ERROR FOLLOW instruction. before the FOLLOW instruction, and then re-
• An attempt was made to re- execute the FOLLOW instruction.
execute the FOLLOW instruction
after interrupting it.
4634 FOLLOWING 0 The manipulator motion speed • Reduce the bending speed.
SPEED OVER exceeded the limit during the • Perform the teaching again so that the
Following motion. manipulator moving distance becomes
• With the specified bending speed, shorter.
the manipulator motion speed
exceeds the maximum speed.
4635 CANNOT --- The called job could not be Correct the control group specified by the
EXECUTE executed because the specified CALL instruction.
COMMON JOB control group was shared with the
called job. (Subcode: The related
control-group)
4636 THICKNESS --- Incorrect workpiece thickness
ERROR (Sub code: Gun number)
8-113
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
4637 TRACK CHG --- No workpiece presence/absence Check the workpiece presence/absence data
WORK IN/NOT data at switching the for the synchronization section.
NOT FOUND synchronization section. (Subcode:
Conveyor characteristic file
number)
4638 TRACKING CHG --- No workpiece type data at Check the workpiece type data for the
WORK ID NOT switching the synchronization synchronization section.
FOUND section. (Subcode: Conveyor
SYMOVJ INST An internal control error occurred during the • Reset the alarm, and then try again.
EXECUTE ERROR SYMOVJ motion. If the error occurs again, contact your
1 • The moving amount in the Yaskawa representative.
orientation at the SYMOVJ motion
position could not correctly be
calculated.
2 • The conveyor moving amount is Set the conveyor moving amount for the
not specified for the SYMOVJ SYMOVJ motion.
4639 motion.
3 • An error occurred in the • Reset the alarm, and then try again.
preparation process of the If the error occurs again, contact your
manipulator motion start position Yaskawa representative.
for the SYMOVJ motion.
4 • An error occurred in the Reset the alarm, and then try again.
preparation process of the If the error occurs again, contact your
manipulator motion end position Yaskawa representative.
for the SYMOVJ motion.
WRONG An error occurred when executing a PSTART
EXECUTION OF instruction.
PSTART INST 1 • No axis data of control group to be
disconnected
2 • An attempt was made to
disconnect a control group other
4640 than the occupation control group Correct the PSTART instruction.
during prereading processing.
3 • An attempt was made to
disconnect a control group other
than the occupation control group
when executing a PSTART
instruction.
4641 CANNOT --- The disconnected control group Do not use the control group disconnected by
EXECUTE JOB could not be moved. itself for its own move instruction.
(SEPARATE • The control group disconnected
GROUP) by itself was used for its own
move instruction. (Subcode: The
disconnected control group used
by a move instruction)
SPOT WELDER I/F An error occurred between the controller and • Reset the alarm, and then try again.
ERROR (ASW) spot welder. • Turn the power OFF then back ON.
1 • The controller could not access If the error occurs again, contact your
the welder. Yaskawa representative.
2 • The controller could not send an

instruction to the welder because
4644 the welder was busy in
processing.
3 • The welder could not receive the
instruction sent from the
controller.
102 • The specified welder number Check the specified welder number (system),
(system) could not be found. and specify the correct welder number.
8-114
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
4645 NOT PERMIT --- Hover weaving could not be • Correct the job.
FIXED-WEAV ON executed. • Reset the alarm, and then try again.
SWVON • The hover weaving is disabled in • Turn the power OFF then back ON.
PALLETIZING 1 The setting of the palletizing • Set the palletizing condition setting file to
EXECUTE ERROR condition configuration file is "Completed".
incomplete.
4 Palletize completion universal • Change the palletize completion universal
output number range exceeds the output signal number of the palletizing
limit. condition setting file in the user output
signal point of contact number.
5 During the palletize start instruction • Delete the palletize start instruction in the
execution, the palletize start palletize section.
instruction is executed again
4651 (double execution).
6 The value of the palletizing number • Check if the palletizing number of current
present value output register (or I position output register (or I variable) and
variable) is more than the total total number of output register (or I
number output register (or I variable) is not changed by another
variable). function.
7 Palletize completion universal • Reset the palletize completion universal
output signal is turned ON at output signal.
palletize start instruction execution.
8 Palletize end instruction is not • Register the palletizing end instruction.
registered.
4800 WDT ERROR --- Watchdog timer error in the • Turn the power OFF then back ON after
(CONVERTER) converter. cooling the power supply contactor unit.
No response from the converter. If the error occurs again, contact your
4850 REGENERATIVE --- Disconnection of SERVOPACK • Turn the power OFF and back ON.
TROUBLE regenerative resistor or failure of • Check the connection of regenerative
(SERVO2) regenerative transistor is resistor cable.
suspected. • Check the settings for manipulator motion
condition (influence by external force, load
condition).
4851 REGENERATIVE --- Regeneration energy exceeds the • Turn the power OFF and back ON.
OVERLOAD tolerance when the motor • Check the settings for manipulator motion
(SERVO2) decelerates. condition (influence by external force, load
condition).
• Check the regenerative resistor capacity.
4852 OVERVOLTAGE --- The main circuit DC voltage of • Turn the power OFF and back ON.
(SERVO2) SERVOPACK is incorrect. • Check the SERVOPACK Primary supply
voltage.
• Check the settings for manipulator motion
condition).
4853 VOLTAGE DROP --- The main circuit DC voltage of • Turn the power OFF and back ON.
(SERVO2) SERVOPACK is incorrect. • Check the SERVOPACK Primary supply
voltage.
• Check the settings for manipulator motion
condition).
8-115
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
4854 OVER SPEED --- The rotation speed of the servo • Turn the power OFF and back ON.
(SERVO2) motor is incorrect. • Check the connections of a motor power
line and an encoder line.
• Check a circumference noise.
4855 OVERLOAD --- The motor is overloaded. • Turn the power OFF and back ON.
(MOMENT) The motor torque has significantly • Check the settings for manipulator motion
(SERVO2) exceeded the rated torque. condition (influence by external force, load
condition).
• Check the connections of a motor power
4856 OVERLOAD --- The motor has continued to be • Turn the power OFF and back ON.
(CONTINUE) overloaded for a certain time. • Check the settings for manipulator motion
(SERVO2) The motor has exceeded the rated condition (influence by external force, load
torque for a long period of time. condition).
*In the case of a large capacity line and an encoder line.
amplifier (The servo pack in use • Replace the SERVOPACK.
when the alarm is emitted is
SGDM-¨¨AC-NX1.) *In the case of a large capacity amplifier
The temperature of SERVOPACK (The servo pack in use when the alarm is
heatsink has exceeded 100°C. emitted is SGDM-¨¨AC-NX1.)
Frequent ON/OFF switching of the • Turn the power OFF and back ON.
servo was detected. • Set the servo ON/OFF switching frequency
Because there is a capacitor in the to no more than 5 switching operations per
power supply section of the large minute.
capacity amplifier, a large charging • Check the settings for manipulator motion
current flows when the servo is condition (influence by external force, load
switched ON. Consequently, if the condition).
servo is switched ON/OFF • Review the ambient operating temperature.
frequently, the main circuit devices • Replace the SERVOPACK.
in the servo pack will deteriorate.
4857 DB OVERLOAD --- Energy exceeds the capacity of • Turn the power OFF and back ON.
(SEVO2) dynamic brake (DB) resistor when it • Check the settings for manipulator motion
stops. condition (influence by external force, load
condition).
4858 RESIST --- The main circuit could have been • Turn the power OFF and back ON.
OVERLOAD repeatedly turned on and off. • Reduce the frequency of the main circuit
(SERVO2) power supply ON/OFF.
4859 HEAT SINK --- The temperature of SERVOPACK • Turn the power OFF and back ON.
OVERHEAT heatsink has exceeded 100°C. • Check the settings for manipulator motion
condition).
4860 ENCODER --- The voltage drop of encoder • Turn the power OFF and back ON.
BATTERY ERROR backup battery is suspected. • Check the connection of encoder backup
(SERVO2) battery and the voltage.
• Replace the MOTOR and SERVOPACK.
4861 ENCODER --- The temperature in the encoder is • Turn the power OFF and back ON.
OVERHEAT abnormal. • Check the settings for manipulator motion
condition).
4862 SPEED A/D --- The A/D converter for the speed • Turn the power OFF and back ON.
ERROR (SERVO2) command input or converted data is • Replace the SERVOPACK.
incorrect.
4863 TORQUE A/D --- The A/D converter for the torque • Turn the power OFF and back ON.
ERROR (SERVO2) command input is incorrect. • Replace the SERVOPACK.
8-116
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
4864 WRONG MOTOR --- The detected direction of torque is • Turn the power OFF and back ON.
ROTATION opposite to that of speed. • Check the connections of a motor power
(SERVO2) line and an encoder line.
4865 POSITION ERROR --- The position deviation pulse has • Turn the power OFF and back ON.
(SERVO2) exceeded the threshold. • Check the settings for manipulator motion
condition).
4866 OPEN PHASE --- The voltage of one of three-phase • Turn the power OFF and back ON.
(SERVO2) input power supplies to • Check the connection of a three-phase
SERVOPACK has dropped. power supply to SERVOPACK.
4867 OVERLOAD --- The motor is overloaded. • Turn the power OFF and back ON.
WARNING • Check the settings for manipulator motion
condition).
4868 REGENERATIVE --- Regeneration energy exceeds the • Turn the power OFF and back ON.
OVERLOAD tolerance when the motor • Check the settings for manipulator motion
WARN (SV2) decelerates. condition (influence by external force, load
condition).
• Check the regenerative resistor capacity.
4869 MECHATROLINK --- The MECHATROLINK • Turn the power OFF and back ON.
DATA SET communication data setting error. • Contact your Yaskawa representative.
WARNING(SV2)
4870 MECHATROLINK --- The MECHATROLINK • Turn the power OFF and back ON.
COMMAND communication command is • Contact your Yaskawa representative.
WARNING(SV2) incorrect.
4871 MECHATROLINK2 --- The MECHATROLINK • Turn the power OFF and back ON.
COMMAND communication is incorrect. • Check the wiring around the
WARNING(SV2) MECHATROLINK communication cable.
• Take some action against noises from the
MECHATROLINK communication cable.
4873 BATTERY --- Warning display indicating the • Turn the power OFF and back ON.
WARNING voltage drop of the absolute • Check the battery connection.
(SERVO2) encoder battery. • Replace the battery.
4876 POSITION ERROR --- The position deviation pulse has • Turn the power OFF and back ON.
WARNING exceeded the tolerance. • Check the settings for manipulator motion
condition).
line.
4901 CUBE/AXIS --- The manipulator has moved into • Check the position in the step (move
INTERFERENCE 1 the specified cube area 1 or the instruction) where the alarm occurred.
maximum or minimum value of the • Change the position in the step (move
axis interference 1 was exceeded. instruction) where the alarm occurred.
• Check the interference region.
8-117
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
INTERFERENCE the specified cube area 10 or the instruction) where the alarm occurred.
10 maximum or minimum value of the • Change the position in the step (move
8-118
RE-CHO-A104
150133-1CD
8 Alarm
Alarm Message List

Alarm Sub
Number Code
8-119
RE-CHO-A104
150133-1CD
8 Alarm
8.4 Confirming Method for Settings and Connection of Axis Configuration, Amplifier, Motor, and
Converter, etc.of the System
Confirming Method for Settings and Connection of

Axis Configuration, Amplifier, Motor, and Converter,
etc.of the System
In this chapter, the confirming methods for settings and connection of axis configuration,
amplifier, motor and converter, etc. of the system, which are necessary for the
countermeasures when an alarm is activated, are described.
Only the confirming methods for settings and connection of axis configuration, amplifier,
motor and converter, etc. of the system are described in this chapter. Therefore, please
do not change the settings of them. Should the settings are changed, the system may not
work properly. To avoid this to happen, backup the stem beforehand by following the
procedures in " 8.4.1 Data Backup "8.4.1.
Data Backup
Operation Explanation
1 Turn ON the power supply

while pressing the [MAIN
MENU].
2 Change the security to edit

or management mode.
3 Insert a CompactFlash
into the CpompactFlash
slot on the programming
pendant.
4 Select {TOOL} under the The {TOOL} sub menu window appears.
Main Menu.
8-120
RE-CHO-A104
150133-1CD
8 Alarm
5 Select {CompactFlash}. The ConpactFlash window appears. The items marked

with "■" cannot be selected.
6 Select "CMOS SAVE". The confirmation dialog box appears.
8-121
RE-CHO-A104
150133-1CD
8 Alarm
7 Select “YES”. Select {YES} to save the CMOS data into the
CompactFlash.
When saving the file, if the CMOS.BIN file already exists in

the CompactFlash, the following confirmation dialog box
appears.
Select {YES} to overwrite the CMOS.BIN file in the
CompactFlash.
8 Wait the data to be saved. While saving, the message "Saving system data. Don’t
turn the power off." is displayed.
When the buzzer on the programming pendant sounds
and the message disappears, the save is completed.
Depending on the version of software, the

abovementioned message is not displayed. In
NOTE this case, confirm that the save is completed by
the buzzer sound of programming pendant.
If it is impossible to confirm by the buzzer, move
the cursor up/down. The cursor does not move
while saving is in progress.
8-122
RE-CHO-A104
150133-1CD
8 Alarm
System Setting Window Displaying Method in the

Maintenance Mode
In the maintenance mode, settings and connection of amplifier, motor and converter, etc. and
axis configuration of the system can be confirmed.
1 Turn ON the power supply

while pressing the [MAIN
MENU].
2 Change the security to edit

or management mode.
3 Select {SYSTEM} under The SYSTEM window appears.

the Main Menu.
DISPLAY SETUP
Main Menu Short Cut
4 Select {SETUP}. The SETUP window appears.
8-123
RE-CHO-A104
150133-1CD
8 Alarm
5 Select {CONTROL The control groups currently set appear.

GROUP}.
6 Select {ENTER}. Configurations of each control group appear.
8-124
RE-CHO-A104
150133-1CD
8 Alarm
Confirmation of Servo Control Board Settings

Corresponding servo control board (SV#1 to 4) for each control group can be confirmed.
n Confirmation on the Setting Window

On the setting window, confirmation of the corresponding servo control board (SV#1 to 4) for
each control group is possible.
Display the window below by following the procedures described in " Fig. 8.4.2 System
Setting Window Displaying Method in the Maintenance Mode ", and then, corresponding
servo control board for each control group can be confirmed.
The word SV shows the servo control board and each #1 and #2 shows the servo control
board number.
(The part circled with .)
- Details of the window above.

R1 (Robot 1) is set to the servo control board1 (SV#1).
B1 (Base 1) is set to the servo control board1 (SV#1).
R2 (Robot 2) is set to the servo control board2 (SV#2).
S1 (Station 1) is set to the servo control board2 (SV#2).
S2 (Station 2) is set to the servo control board2 (SV#2).
8-125
RE-CHO-A104
150133-1CD
8 Alarm
n Confirmation Using Hardware

With the hardware, the servo control board number can be confirmed.
The number is defined by both the number of the rotary switch (S1) which is located in front of
the servo control board and the type of NIF01 unit.
- When the unit type of NIF01-1 is used.
Servo control board1 (SV#1): The rotary switch number is “0”.
SV#1 SV#2 SV#3 SV#4

JZNC-
NIF01-1 SGDR-AXA01 SGDR-AXA01 SGDR-AXA01 SGDR-AXA01
(SGDR-AXA02) (SGDR-AXA02) (SGDR-AXA02) (SGDR-AXA02)
Rotary SW=0 Rotary SW=1 Rotary SW=2 Rotary SW=3
CN02 CN02 CN02 CN02

CN01
Servo Control Board Settings when NIF01-1 is Used
- When the unit type of NIF01-2 is used.

Servo control board1 (SV#1):
The number of the rotary switch which is connected to CN01 of NIF01-2 is “0”.
SV#1 SV#3
SGDR-AXA01 SGDR-AXA01
(SGDR-AXA02) (SGDR-AXA02)
JZNC- Rotary SW=0 Rotary SW=1

NIF01-2
CN02 CN02
CN01
CN02
CN02 CN02
SGDR-AXA01 SGDR-AXA01
(SGDR-AXA02) (SGDR-AXA02)
Rotary SW=0 Rotary SW=1
SV#2 SV#4
Servo Control Board Settings when NIF01-2 is Used
8-126
RE-CHO-A104
150133-1CD
8 Alarm
Confirmation of Servo Control Board Connector

Settings
Corresponding servo control board connectors for each axis can be confirmed.

On the setting window, confirmation of the corresponding servo control board connectors for
each axis is possible.
Display the window below by following the procedures described in Fig.8.4.2 "System Setting
Window Displaying Method in the Maintenance Mode", and then, servo control board
connectors for each axis can be confirmed.
The numbers: CN<1 2 3 4 5 6 7 8 9> show the servo control board connectors and the values
in [ ] show the axis number.
Corresponding Connector Number for each Axis
Axis Robot Station axis Base

numbe axis
r
R1 R2 S1 S2 B1
1 S S 1 1 1
2 L L 2 2
3 U U 3
4 R R
5 B B
6 T T
8-127
RE-CHO-A104
150133-1CD
8 Alarm

1 axis of R1 (Robot 1) is connected to the connector1 of the servo control board SV#1
1 axis of B1 (Base 1) is connected to the connector7 of the servo control board SV#1.
2 axis of B1 (Base 1) is connected to the connector8 of the servo control board SV#1.
1 axis of R2 (Robot 2) is connected to the connector3 of the servo control board SV#2.
1 axis of S1 (Station 1) is connected to the connector7 of the servo control board SV#2.
1 axis of S2 (Station 2) is connected to the connector8 of the servo control board SV#2.
8-128
RE-CHO-A104
150133-1CD
8 Alarm

The number of the servo control board connectors are shown in the table and the figure
below.
Also, the connectors on the servo control board are connected to the amplifier as shown
below.
Servo Control Board and Connectors
Servo control board

Servo control board
connector
AXA01, AXB01
(CN)
1
CN04
2
3
CN05
4
5
CN06
6
7 CN08
8 CN09
9 CN10
Connector 1,2 CN04 Amplifier (on the first axis)

Amplifier (on the second axis)
Connector 3,4 CN05 Amplifier (on the third axis)
Amplifier (on the fourrth axis)
Connector 5,6 CN06 Amplifier (on the fifth axis)
Amplifier (on the sixth axis)
SGDR-AXA01
SGDR-AXB01
Connector 7 CN08 Amplifier (on the seventh axis)
Connector 8 CN09 Amplifier (on the eighth axis)
Connector 9 CN10 Amplifier (on the ninth axis)
Servo Control Board Connectors and

Connection Between Connectors on the Servo Control Board and Amplifiers
8-129
RE-CHO-A104
150133-1CD
8 Alarm
Confirmation of Amplifier Settings

Corresponding amplifiers to each axis can be confirmed.

On the setting window, confirmation of the corresponding amplifiers to each axis is possible.
Display the window below by following the procedures described in Fig.8.4.2 "System Setting
Window Displaying Method in the Maintenance Mode", and then, amplifiers to each axis can
be confirmed.
The connectors on the servo controller board are connected to each amplifier as shown in
section “Confirmation Using Hardware” in section 8.4.4 “Confirmation of Servo Control Board
Connector Settings”.
The numbers: CN<1 2 3 4 5 6 7 8 9> show the amplifier number and the values in [ ] show the
axis number.
The window below shows the corresponding amplifiers to each axis.

1 axis of R1 (Robot 1) is set to the amplifier1 connected to the servo control board SV#1
1 axis of B1 (Base1) is set to the amplifier7 connected to the servo control board SV#1
2 axis of B1 (Base1) is set to the amplifier8 connected to the servo control board SV#1
1 axis of R2 (Robot 2) is set to the amplifier3 connected to the servo control board SV#2
8-130
RE-CHO-A104
150133-1CD
8 Alarm

With the hardware, the amplifier number can be confirmed.
The number is punch marked on the metal plate on which the amplifier is mounted.
AMP4 AMP5 AMP6
AMP1 AMP2 AMP3
In case a servo pack (amplifier-converter integrated type) is mounted, the servo pack number
can be confirmed by the sticker attached in front of it.
8-131
RE-CHO-A104
150133-1CD
8 Alarm
Each amplifier is connected to the connector (CN04, CN05, CN06, CN08, CN09 and CN10)
on the servo control board as shown in the table and figure below.
Corresponding Amplifier to Connectors on the Servo Control Board
Connectors on
the Servo control
Amplifier
servo control board
number
board AXA01, AXB01
(CN)
1 1
CN04
2 2
3 3
CN05
4 4
5 5
CN06
6 6
7 CN08 7
8 CN09 8
9 CN10 9
Connector1,2 CN04 Amplifier (on the first axis)

Amplifier (on the second axis)
Connector3,4 CN05 Amplifier (on the third axis)
Amplifier (on the fourrth axis)
Connector5,6 CN06 Amplifier (on the fifth axis)
Amplifier (on the sixth axis)
SGDR-AXA01
SGDR-AXB01
Connector7 CN08 Amplifier (on the seventh axis)
Connector8 CN09 Amplifier (on the eighth axis)
Connector9 CN10 Amplifier (on the ninth axis)
Connection Between Connectors on the Servo Control Board and Amplifiers
8-132
RE-CHO-A104
150133-1CD
8 Alarm
Confirmation of Power Supply Contactor Unit Settings

Corresponding power supply contactor unit for each control group can be confirmed.

On the setting window, confirmation of the corresponding power supply contactor unit for each
control group is possible.
Display the window below by following the procedures described in Fig. 8.4.2 “System Setting
Window Displaying Method in the Maintenance Mode”, and then, corresponding power supply
contactor unit for each control group can be confirmed.
The word TU indicates the power supply contactor unit and #1 and #2 show the number of
power supply contactor unit.

R1 (Robot 1) is set to power supply contactor unit 1 (TU#1).
B1 (Base1) is set to power supply contactor unit 2 (TU#2).
R2 (Robot 2) is set to power supply contactor unit 1 (TU#1).
S1 (Station 1) is set to power supply contactor unit 2 (TU#2).
S2 (Station 2) is set to power supply contactor unit 2 (TU#2).
8-133
RE-CHO-A104
150133-1CD
8 Alarm

The power supply contactor unit number can be confirmed.
The power supply contactor unit number is defined by the rotary switch (S1) which is located
in front of the unit.
TU#1: The rotary switch number is “1”.

TU#1 TU#2 TU#3 TU#4 TU#5 TU#6

Power supply Power supply Power supply Power supply Power supply Power supply
contactor unit1 contactor unit2 contactor unit3 contactor unit4 contactor unit5 contactor unit6
SGDR-AXA01
(SGDR-AXA02) RotarySW=1 RotarySW=2 RotarySW=3 RotarySW=4 RotarySW=5 RotarySW=6
The Power Supply Contactor Unit Number and Rotary Switch Number
8-134
RE-CHO-A104
150133-1CD
8 Alarm
Confirmation of Brake Wirings

Corresponding brake connector (CN08) for each axis motor brake can be confirmed.

On the setting window, confirmation of the corresponding brake connector (CN08) for each
axis motor brake is possible.
Window Displaying Method in the Maintenance Mode”, and then, corresponding brake
connector (CN08) number for each axis motor brake can be confirmed.
The numbers: BRK<1 2 3 4 5 6 7 8 9> show the brake connector (CN08) number and the
values in [ ] show the axis number.
Connector number of brake

Motor brake connector (CN8)
Robot
at on power supply contactor
unit 1(TU#1)
R1 1-axis 1
(Robot1) 2-axis 2
3-axis 3
4-axis 4
5-axis 5
6-axis 6
8-135
RE-CHO-A104
150133-1CD
8 Alarm
Connector number of brake

Motor brake connector (CN8)
Robot
at on power supply contactor
unit 2(TU#2)
R2 1-axis 3
(Robot2) 2-axis 2
3-axis 1
4-axis 5
5-axis 6
6-axis 4

Each axis motor brake which is set on the maintenance mode setting window is connected to
the power supply contactor unit connector (CN8).
The numbers: BRK<1 2 3 4 5 6 7 8 9> show the brake connector (CN08) number and the
values in [ ] show the axis number.
Details are described as below when the setting on the setting window is as follows:
TU BRK <1 2 3 4 5 6 7 8 9>
#1 [1 2 3 4 5 6 - - -]
The first axis motor brake is connected to the number "1" of the connector (CN08) on the
power supply contactor unit (TU#1).
The second axis motor brake is connected to the number "2" of the connector (CN08) on the
The third axis motor brake is connected to the number "3" of the connector (CN08) on the
The fourth axis motor brake is connected to the number "4" of the connector (CN08) on the
The fifth axis motor brake is connected to the number "5" of the connector (CN08) on the
The sixth axis motor brake is connected to the number "6" of the connector (CN08) on the
TU#1
Power supply
contactor unit
SGDR-AXA01 RotarySW=1
CN08 9
(SGDR-AXA02) 87
65
43
21
Motor (on the first axis)

Motor (on the second axis)
Motor (on the third axis)
Motor (on the fourrth axis)
Motor (on the fifth axis)
Motor (on the sixth axis)
8-136
RE-CHO-A104
150133-1CD
8 Alarm
Confirmation of the Converter Settings

Corresponding converters for each control group can be confirmed.

On the setting window, confirmation of the corresponding converters for each axis is possible.
Window Displaying Method in the Maintenance Mode”, and then, corresponding converters
for each axis can be confirmed.
The numbers: CN<1 2 3 4 5 6 7 8 9> show the servo control board connectors and the values
in [ ] show the converter number.
For the servo control board connector settings, refer to Fig. 8.4.4 “Confirmation of Servo
Control Board Connector Settings”.

6-axis of the R1 (Robot 1) is set to the connector 6 on the servo control board SV#1, and the
connector is set to the converter CV1.
1-axis of the S1 (Station 1) is set to the connector 7 on the servo control board SV#2, and the
connector is set to the converter CV2.
8-137
RE-CHO-A104
150133-1CD
8 Alarm

With the hardware, the converter number can be confirmed.
The converter number is defined by the connector connected to the servo control board.
-When SGDR-AXA01 is used
CV1 is connected to CN01 of the servo control board (SGDR-AXA01)
CV2 is connected to CN08 of the servo control board (SGDR-AXB01)
SGDR-AXA01 CN01 CV1

Amplifier (on the first axis) Motor (on the first axis)
Converter
(for all 6 axes) Amplifier (on the second axis) Motor (on the second axis)
Amplifier (on the third axis) Motor (on the third axis)
Amplifier (on the fourrth axis) Motor (on the fourrth axis)
Amplifier (on the fifth axis) Motor (on the fifth axis)
Amplifier (on the sixth axis) Motor (on the sixth axis)
SGDR-AXB01 CN08 Servo pack 1 CV2
Motor (on the seventh axis)
(amplifier-converter integrated type)
Servo pack 2 CV3
CN09 (amplifier-converter integrated type)
Motor (on the eighth axis)
Servo pack 3 CV4

CN10 (amplifier-converter integrated type)
Motor (on the ninth axis)
Converter Connection when AXA01 is Used

-When SGDR-AXA02 is used
Servo pack 1 CV1

SGDR-AXA02 CN04 Motor (on the first axis)
Servo pack 2 CV2
CN05 (amplifier-converter integrated type) Motor (on the second axis)
Servo pack 3 CV3

CN06 Motor (on the third axis)
SGDR-AXB01 CN08 Servo pack 4 CV4
(amplifier-converter integrated type) Motor (on the fourrth axis)
Servo pack 5 CV5

CN09 Motor (on the fifth axis)
Servo pack 6 CV6
CN10 (amplifier-converter integrated type) Motor (on the sixth axis)
Converter Connection when AXA02 is Used
8-138
RE-CHO-A104
150133-1CD
9 Error
9.1 Error Message List
9 Error
Error Message List
Error warns the operator not to advance to the next operation caused by a wrong operation or
the access method when using the programming pendant or an external equipment
(computer, PLC, etc.).
When an error occurs, confirm the content of the error then release the error.
To release the error, perform either of the following operations:

• Press [CANCEL] on programming pendant.
• Input alarm/error reset signal (system input).
NOTE An error is different from an alarm because it does not stop the robot even if it
occurred while the robot was operated (during playback).
Main Menu ShortCut Cannot insert/modify/delete for axis detachment
When two or more errors occur, appears in the message display area. Activate the
message display area and press [SELECT] to view the list of current errors.
5/9
Cannot load macro job at current security mode
HELP
Cannot insert/modify/delete for group axis detachment
CLOSE
Cannot insert/modify/delete for axis detachment
To view details of the selected error contents, select "HELP". To close the error list, select
"CLOSE". To release all the errors, press [CANCEL].
9-1
RE-CHO-A104
150133-1CD
9 Error
System and General Operation
Error No. Data Error Message Contents
Turn off servo power and perform It cannot be operated while

10 -
corrective action servo power supply is ON.
Depress TEACH Out of specified operation

20 -
mode
30 - Illegal setting for number of variables Parameter setting error
Illegal setting for number of variable-

31 -
names
Undefined robot position variables Position variable cannot be

40 -
used.
Undefined points (ORG, XX, XY) Not registered user

60 - coordinates basic 3 points
(ORG, XX, XY)
Program and current tool different The tool number registered

with teaching position data
70 - does not match the tool
number selected at the
programing pendant.
80 - Same position in the 3 points
100 - On overrun recovery status
110 - Turn ON servo power
120 - Set to PLAY mode
130 - No start using external signal
140 - No start using P.P.
180 - TEACH mode select signal ON
190 - Set variable number
200 - Defined group axis
210 - Undefined coordinated robots
212 Cannot register group combination
230 - While releasing soft limit
240 - Undefined robot
270 - Undefined gun condition file
280 - Lack of number of I/O points
9-2
RE-CHO-A104
150133-1CD
9 Error
290 - Cannot set same No.
Station axes are not at the same

291 -
point.
300 - Undefined user frame
310 - Cannot register Master JOB
320 - Cannot operate CHECK-RUN
330 - Cannot operate MACHINE LOCK
340 - Cannot operate Master JOB
350 - Cannot initialize
Position not checked Second home position was not

380 -
checked.
Select joint coordinate system and

383 -
perform forward operation.
390 - Can specify servo off by safety relay
Time could not be measured Time could not be measured

410 -
for TRT function.
Incorrect number of taught points The number of the taught

420 - points for tool calibration is
incorrect.
430 - Register start reserved JOB
460 - Excess time for measuring
500 - Undefined robot calibration data
510 - Undefined axis
Cannot select two coordinated

520 -
combination
530 - Start reservation mode
Start reserved JOB change prohibit

550 -
is set
Cannot teach position while soft limit

560 -
released
Register group axis combination [SYNCHRO] was pressed for

590 - coordinated job which was not
registered as group.
600 - Out of setting data range
9-3
RE-CHO-A104
150133-1CD
9 Error
610 - Cannot use the user coordinate
620 - Select JOB (robot)
650 - Incorrect measured data
660 - Wrong data type of position variable
- Defined data
680
XXX File No.
700 - Wrong CMOS memory board type
710 - Canceled palletizing shift value
It is already registered for IN/OUT

∗
signal name.
It is registered as a universal
721 0
input signal name.
It is registered as a universal
1
output signal name.
It is already registered for Variable

∗
name.
It is registered as a byte type

0
(B) variable name.
It is registered as an integer
1
type (I) variable name.
It is registered as a double-
2 precision integer type (D)
variable name.
It is registered as a real type

3
(R) variable name.
722
It is registered as a character-
4
string type (S) variable name.
It is registered as a robot-axis
5 position type (P) variable
name.
It is registered as a base-axis
6 position type (BP) variable
name.
It is registered as a station-axis
7 position type (EX) variable
name.
9-4
RE-CHO-A104
150133-1CD
9 Error
It is already registered for Local

∗
variable name.
It is registered as a byte type

0
local (LB) variable name.
It is registered as an integer
1
type local (LI) variable name.
It is registered as a double-
2 precision integer type local
(LD) variable name.
It is registered as a real type

3
local (LR) variable name.
723
It is registered as a character-
4 string type local (LS) variable
name.
It is registered as a robot-axis
5 position type local (LP)
variable name.
It is registered as a base-axis
6 position type local (LBP)
variable name.
It is registered as a station-axis
7 position type local (LEX)
variable name.
9-5
RE-CHO-A104
150133-1CD
9 Error
The existing names cannot be When the signal name alias

overwritten function or the variable name
alias function is valid, the
signal or variable whose name
∗ is already registered cannot be
overwritten with another name
when the I/O name data or the
variable name data is loaded
from external memory.
A byte type (B) variable name

0
is different.
An integer type (I) variable

1
name is different.
A double-precision integer type

2
(D) variable name is different.
724 A real type (R) variable name
3
is different.
A character-string type (S)

4
variable name is different.
A robot-axis position type (P)

5
A base-axis position type (BP)

6
A station-axis position type

7
(EX) variable name is different.
A universal input name is

20
different.
A universal output name is

21
different.
This name cannot be defined The entered name contains an

740 -
unusable character.
760 - Error in start condition set
770 - During robot operation
The gun of designation is not

800 -
connected
The group axis of designation is not

801 -
connection
810 - Servo power supply is limited
9-6
RE-CHO-A104
150133-1CD
9 Error
820 - Modification range over
930 - Undefined conveyor calibration data
940 - Forced pressure signal ON
950 - Negative correction distance
960 - I/O axis mode requesting
970 - ERRSVCPU signal error
971 - ERRCPU signal error
TIMER DATA TRANSMISSION

∗
ERROR
The data was not written

0
successfully.
The data command was not

980 1
The data command has not

2
been executed yet.
3 Timer error.
4 H system is protected.
9-7
RE-CHO-A104
150133-1CD
9 Error
Editing
1010 - EDIT LOCK mode
1020 - Enter correct value
1030 - Unauthorized ID No.
1050 - Enter correct date
1060 - Enter correct clock
1070 - Enter an ID number in 4-8 figures
1080 - Negative value can’t be set
Enter correct value (START-END The relationship of the

signal no) following signal allocation: the
start number >= the end
1090 -
number.
• Welding condition
• Welding group output
9-8
RE-CHO-A104
150133-1CD
9 Error
Job Defined Data
2010 - Incorrect character
2020 - Name not entered
2030 - Undefined JOB name
2040 - Defined JOB name
2050 - Address not found
2070 - Set robot exactly to taught position
2080 - Press INSERT or MODIFY
Only modifying move instruction

2090 -
possible
2100 - JOB cannot be edited.
2110 - Over soft limit
Over soft limit. Adjust center

∗
2111 position or pulse width.
XXX Axis number
Cannot insert/alter/delete with

2120 -
servo off
Inserting is not possible from this

2150 -
point
Cannot modify or delete this

2160 -
position
Press INSERT to record same step

2170 -
as previous step
2180 - Cannot insert data
2210 - Illegal data setting
2220 - Display edit instruction
2240 - Excessive instruction equation
Unmatched number of parentheses

2250 -
in equation
2260 - Wrong group axis selection
Cannot insert any more instruction

2270 -
in JOB
9-9
RE-CHO-A104
150133-1CD
9 Error
∗ JOB memory is full
1 Lack of position file memories
Lack of JOB registering

2
memories
2280
3 Lack of instruction file memories
4 Lack of memory pool
Lack of pass condition file for

5
multilayer
2290 - Undefined master JOB
∗ Undefined SUB Master JOB
1 Sub-master 1
2 Sub-master 2
3 Sub-master 3
2291 4 Sub-master 4
5 Sub-master 5
6 Sub-master 6
7 Sub-master 7
8 Sub-master 8
2292 - Undefined MASTER START JOB
∗ Undefined SUB START JOB
1 Sub-master 1
2 Sub-master 2
3 Sub-master 3
2293 4 Sub-master 4
5 Sub-master 5
6 Sub-master 6
7 Sub-master 7
8 Sub-master 8
Cannot teach JOB without group-

2300 -
axis specification
9-10
RE-CHO-A104
150133-1CD
9 Error
∗ Same label exists

2310
XXX Line No.
2340 - Pasted data not found
2360 - Cannot create editing area
Cannot cut/copy NOP and END

2370 -
instructions
2390 - Wrong group axis selection
2400 - Cannot move in cut & paste editing
2430 - Reverse data not found
Move C-and W-axis to basic Laser cutting

2440 -
position
2450 - Relative JOB not permitted
2470 - Wrong JOB type
2480 - Wrong JOB coordinates setting
2500 - Cannot convert the JOB
Cannot convert positions as macro

∗
arguments
1 The control group is not set.
2501 The position data of the base

2
axis does not exist.
The position data of the base

3 axis exists, but the data of the
robot axis does not exist.
2510 - Cannot correct position in the JOB
2520 - Enter JOB name
2530 - Illegal step number
2540 - Enter step number
2550 - Duplicated step number
2551 - Duplicated line number
Cannot correct steps of position

2560 -
variables and REFP
2570 - The step does not contain speed
9-11
RE-CHO-A104
150133-1CD
9 Error
The step dose not contain PL/

2580 -
CONT
2590 - Soft limit range over
Cannot teach position in concurrent

2600 -
JOB
2610 - Wrong JOB kind
Cannot correct play speed in the

2620 -
JOB
2630 - Conveyor position not reset
2640 - Incorrect JOB name
Defined JOB name The job with the same name as

2650 - a job already registered was
attempted to be restored.
2670 - Undefined target JOB
Relative job can’t be shifted with

2710 -
pulse type
2730 - Cannot use robot macro JOB
2740 - Cannot use concurrent macro JOB
Cannot use JOB with group-axis

2750 -
specification
Cannot insert/modify/delete for

2760 -
group axis detachment
Axis is separated.
2761 -
Cannot add, modify, or delete.
Cannot reverse data of

2770 -
SVSPOTMOV instruction
2780 - Arithmetic error
Step exceeding operation range. When the position data was

converted by using the PMT
2790 - function, it was converted to the
value which exceeds the range
of motion of the manipulator.
9-12
RE-CHO-A104
150133-1CD
9 Error
External Memory Equipment
9-13
RE-CHO-A104
150133-1CD
9 Error
Cannot use FC1 FC2 and PC (RS-

3000 -
232C) when vision function is valid.
Floppy disk drive cable not

3010 -
connected
Floppy disk not inserted into floppy

3020 -
disk drive
CompactFlash not inserted into

3021 -
CompactFlash slot (PP)
3030 - Floppy disk protection is ON
File not saved on floppy disk or

3040 -
CompactFlash
File saved on floppy disk or

3050 -
CompactFlash
Out of memory on floppy disk or

3060 -
CompactFlash
Number of files on floppy disk or

3070 -
CompactFlash is full
I/O error on floppy disk or

3080 -
CompactFlash
Transmission error with floppy disk

∗
or CompactFlash
1 Framing error
2 Overrun error
3 Parity error
4 Data code error

3090
5 Data read error
6 Data write error
7 Data time out
8 Serial I/O error
Error other than described

9
above
9-14
RE-CHO-A104
150133-1CD
9 Error
Total checksum error The following files are corrupted.

Use the correct data.
· CMOS.BIN
3100 -
· CMOSBK.BIN
· CMOSBK1.BIN to
CMOSBK99.BIN
3110 - Syntax error
HEX code error An error was detected when

BATCH CMOS file or BATCH
∗
USER MEMORY file is loaded.
Use the correct data.
Specification error of data

1
3120 decode
Specification error of EOF

2
record
3 Record type error
4 Total check error of record
Verify error A difference was found when

3130 -
verifying a file.
Wrong pseudo instruction A syntax error was detected

when a job file or a condition file
3140 - was loaded or verified. Load the
correct data, or correct the
syntax and reload.
Concurrent I/O record error A syntax error was detected

when the CIO program was
∗
loaded or verified. Use the
correct CIO program.
1 Format error
2 Ladder program is too long.

3150 3 Exceed the range of the data
Specification error of channel

4
No.
5 Specification error of relay No.
6 Timer value error
7 Specification error of timer No.
9-15
RE-CHO-A104
150133-1CD
9 Error
Cannot load illegal system data The CIO program with the
modified I/O alarm or I/O
message of the system part was
3160 -
attempted to be loaded. Load
the CIO program whose system
part was not modified.
Condition file data error An error was detected when a

∗ condition file was loaded or
verified. Load the correct data.
1 Format error
3170
2 Specified file No. is omitted.
3 Specified tool No. is omitted.
4 User file is not registered.
Concurrent I/O data transmission An error was detected when the

3180 - error CIO program was loaded. Load
the correct CIO program.
9-16
RE-CHO-A104
150133-1CD
9 Error
Error in JOB data record A syntax error was detected

∗ when a job file was loaded.
Load the correct job file.
Record on the number of

1 position data (NPOS) is wrong
for the format.
Record on the user coordinate

2 No. (USER) is wrong for the
format.
Record on the tool No. (TOOL)

3
is wrong for the format.
Record on the position data

4
section is wrong for the format.
Record on the robot type of XYZ

5 data (RCONF) is wrong for the
format.
Date (DATE) record is wrong for

6
3190 the format.
Comment (COMM) record is

7
wrong for the format.
Record on the JOB attribute

8 data (ATTR) is wrong for the
format.
Control group (GROUP) record

9
Local variable (LVARS) record is

10
wrong for the format.
JOB argument (JARGS) record

11
Record on the teaching

coordinates for relative job
12
(FRAME) is wrong for the
format.
Position data coordinates do not

13
match relative job coordinates.
NOP or END instruction not found NOP instruction or END

instruction does not exist in the
3200 -
job file which was loaded or
verified. Use the correct job file.
9-17
RE-CHO-A104
150133-1CD
9 Error
Position No. storage area not found Failed to read the position data
3210 - when a job file was loaded.
Load the correct job file.
9-18
RE-CHO-A104
150133-1CD
9 Error
∗ Syntax error in instruction data
2 Interior control error
3 Undefined instruction/tag
4 Instruction/tag shortage
5 Disuse instruction/tag
6 Sub instruction
7 No instruction
8 Invalid instruction
9 Invalid tag
10 Invalid character
11 Undefined intermediate code
12 Intermediate code shortage
13 Syntax stack overflow
14 Syntax stack underflow
Array type tag uncompleted

15
Tag [ARRAY]
3220
Element type tag uncompleted
16
Tag [ELEMENT]
17 Macro JOB unregistered
18 Input format error
19 Data size over
20 MIN value over
21 MAX value over
22 Operation expression error
23 Job call argument setting error
Macro job call argument setting

24
error
25 Position vector setting error
26 System error
27 Soft key designate error
28 Numerical input buffer overflow
9-19
RE-CHO-A104
150133-1CD
9 Error
30 Element format error
35 BOOL TYPE data error
36 CHAR data error
BYTETYPE, BINARY /
37 HEXADECIMAL BYTE TYPE
data error
INTEGER TYPE, DECIMAL

38
WORD TYPE data error
BINARY/HEXADECIMAL
39
DOUBLE PRECISION
40 INTEGER TYPE, DECIMAL
DWORD TYPE data error
3220 BINARY/HEXADECIMAL
41
42 REAL TYPE data error
LADDER SPECIAL TYPE data

43
error
44 JCL text
45 Invalid text
46 LABEL NAME data error
47 JOB NAME data error
48 STRING data error
49 COMMENT data error
58 Invalid instruction/tag detection
Syntax not matched The data to be loaded does not

3230 - match the controller’s system.
Load the correct data.
3240 - Undefined application
Cannot load this file A file which cannot be loaded

3250 -
was selected.
3260 - Excess input data
Cannot verify this file A file which cannot be verified

3270 -
was selected.
9-20
RE-CHO-A104
150133-1CD
9 Error
Wrong welding condition

3280 -
(STANDARD/ENHANCED)
3290 - Serial port not defined
3300 - Serial port being used
3310 - Protocol being used
3320 - Wrong GUN type
3330 - Undefined multilayer data
3340 - Illegal number of multilayer data
Not enough memory The CompactFlash does not

have enough free space.
Remove and insert the
3350 -
CompactFlash, or replace it with
a CompactFlash with enough
free space.
3360 - Invalid folder
3370 - Incorrect folder name Enter the correct folder name.
Drive not ready Remove and insert the

3380 -
free space.
3390 - File not found
3400 - File already exists on the media
Out of memory on the media The CompactFlash does not

have enough free space.
3410 -
free space.
Max number of files has been The maximum number of files

reached which the CompactFlash can
save was exceeded. Delete
3420 - some files in the CompactFlash,
or replace it with a
CompactFlash with enough free
space.
9-21
RE-CHO-A104
150133-1CD
9 Error
I/O error on the drive The CompactFlash was not

recognized. Remove and insert
3430 - the CompactFlash, or replace it
with a CompactFlash with
enough free space.
Wrong media type Use the recommended

3440 -
CompactFlash.
Cannot load macro JOB at current Load in management mode.

3450 -
security mode
∗ Cannot backup CompactFlash The automatic backup failed.
Insufficient CompactFlash
1
3460 memory.
Not accessible to
2
CompactFlash.
Database not found Check that the correct data is

3470 -
written in the CompactFlash.
Database access error Check that the correct data is

3480 -
Same database exists Check that the correct data is

3490 -
Check CompactFlash insertion Remove and insert the

3500 -
free space.
9-22
RE-CHO-A104
150133-1CD
9 Error
∗ Check CompactFlash insertion The automatic backup failed.
The CompactFlash did not have

enough free space for automatic
backup. Remove and insert the
1
free space.
A CompactFlash access error

occurred during automatic
2
free space.
The automatic backup failed.

3 CompactFlash, or replace it with
free space.
3501 The automatic backup failed.

free space.

free space.
Failed to delete old automatic

backup data. Remove and
6 insert the CompactFlash, or
replace it with a CompactFlash
with enough free space.

9-23
RE-CHO-A104
150133-1CD
9 Error
Failed to sort backup files.

free space.

free space.
3501
free space.

free space.
Cannot delete folder. Check Failed to delete the folder.

attribute and inside file Check the attribute of the folder,
3510 -
or check that there is no file in
the folder.
3520 - Same folder exists Use the correct folder name.
Cannot load at current security Change to the correct security

3530 -
mode mode.
CMOS not compatible The data to be loaded does not

3540 - match the controller’s system.
Load the correct data.
Under automatic backup operation. Execute the operation again

∗ Operate after the backup is after the automatic backup is
3550 completed. completed.
The automatic backup is being

101
performed.
Under automatic backup operation. Execute the operation again

∗ Operate ¥SORT FILE¥ after the after the automatic backup is
3551 backup is completed. completed.
The automatic backup is being

101
performed.
9-24
RE-CHO-A104
150133-1CD
9 Error
Failed in sorting backup file Failed to sort files in the AUTO

∗
BACKUP SET display.
The CompactFlash did not have

enough free space for automatic
1
free space.
A CompactFlash access error

occurred during automatic
2
free space.

free space.

3560
free space.

free space.


free space.

free space.
9-25
RE-CHO-A104
150133-1CD
9 Error

free space.
3560
free space.
3570 - Actuator data transmission error
Under backup file access. Operate Execute the operation again

∗ after the access is completed. after the access to the backup
3580 file is completed.
The backup file is being

102
accessed.
Under backup file access. Operate Execute the operation again

∗ ¥SORT FILE¥ after the access is after the access to the backup
3581 completed. file is completed.
The backup file is being

102
accessed.
3610 - Cannot load/save at IO trace mode
9-26
RE-CHO-A104
150133-1CD
9 Error
Concurrent I/O
∗ Illegal relay No.

4010
XXX Line No.
∗ Illegal instruction
4030
XXX Line No.
Relay/register No. duplicated in OUT/ Multiple outputs are

∗ GOUT or arithmetic instruction instructed to the relay or
4040 register.
XXX Line No.
∗ The relay is not used

4050
XXX Line No.
∗ Excess STR-[-NOT] instructions

4060
XXX Line No.
∗ Excess AND [OR] STR instructions

4070
XXX Line No.
∗ Syntax error in CNT instructions

4080
XXX Line No.
∗ Enter STR [-NOT] at head of block Need STR [-NOT]

4090
XXX Line No.
Concurrent I/O memory is full Exceeds memory capacity

4120 -
(10000 steps)
4130 - END instruction not found END instruction not found
Wrong ladder program Position and number of PART

4140 -
instruction are wrong.
Wrong use of GSTR, GOUT GSTR and GOUT is not used

∗
4150 commands together.
XXX Line No.
4190 - Ladder program not found
9-27
RE-CHO-A104
150133-1CD
9 Error
Excess TMR/CNT or arithmetic More than 100 TMR, CNT or

4220 -
instructions arithmetic instruction used
4230 - Syntax error in TMR/CNT instructions
Relay No. duplicated in CIO Program

4240 -
and I/F Panel.
User Registration and Other Operations
Cannot delete under current security With the editing mode or a

5010 - mode. lower security mode, the user
cannot be deleted.
Cannot delete. The user is in the The user who logs on cannot
5020 -
logon status. be deleted.
Not allowed to delete this user name. The system’s standard

5030 -
username cannot be deleted.
5040 - Input user name.
5050 - Input password.
5060 - Input password again.
5070 - This username is already registered.
Cannot register users any more. The maximum number of the

5080 - user accounts which can be
registered is 100.
User name and/or password are not Information is not enough to

5090 -
set. register the user account.
Incorrect input information. Enter the correct username

5100 -
and password.
5110 - The user name is not registered. Enter the correct username.
Selecting ARCOF CONTINUE is

5130 -
prohibited.
9-28
RE-CHO-A104
150133-1CD
9 Error
RPS job cannot be called up during The master cannot be called

∗
playback or running during playback.
0 Master task
1 Sub task 1
2 Sub task 2
5140
3 Sub task 3
4 Sub task 4
5 Sub task 5
6 Sub task 6
7 Sub task 7
ROBOT DETACHMENT cannot be

5170 -
called up during playback or running
5210 - EXSVON signal is OFF
5211 - EXDSW signal is OFF
5220 - Selected display cannot be shown
5240 - Cannot write in the JOB in execution.
Cannot perform position teaching The move instruction cannot

5250 - during PLAY mode. be taught during the play
mode.
Cannot perform other operations The external memory cannot

5260 - during the writing request for playback be operated while writing the
edit JOB. job.
No backup data The encoder backup data

5270 -
does not exist.
9-29
RE-CHO-A104
150133-1CD
9 Error
Maintenance Mode
Too many axes The maximum number of

8010 - axes which can be configured
was exceeded.
Too many I/O points The maximum number of

8020 - points which can be used for
external I/O was exceeded.
Too many boards (XFB01B

8030 -
(MASTER))
8031 - Too many boards (MSC01B)
Too many Timer I/F board The set number exceeded

8032 - the maximum number of
usable Nadex boards.
Memory error (ControlNet output

8040 -
condition)
Memory error (UNIWIRE CONNECT

8041 -
DAT
Memory error (IP Network

8042 -
Configuration data)
8050 - Robot model is not registered
8051 - Select model
8060 - Cannot get UNIWIRE connection data
DHCP is already set to use for another An incorrect value is set in

8070 - item the NETWORK SETUP
display.
DNS is already set to use for another An incorrect value is set in

8071 - item the NETWORK SETUP
display.
DHCP is not set to use An incorrect value is set in

8072 - the NETWORK SETUP
display.
DNS is not set to use An incorrect value is set in

8073 - the NETWORK SETUP
display.
Slave Information not found Failed to retrieve the slave

8074 - information with the
EtherNetIP function.
9-30
RE-CHO-A104
150133-1CD
9 Error
Unable to accept same type of boards The Ethernet function and the
8075 - simultaneously EtherNet IP board were used
simultaneously.
Ethernet is being used by other The Ethernet function and the

8076 - function. EtherNet IP board were used
simultaneously.
VERIFY ERROR (CP02#1) The CP02 board settings are

∗ different from the ones at
8080 configuration.
XXX SL1 application number
VERIFY ERROR (CP02#2) The CP02 board settings are

∗ different from the ones at
8081 configuration.
XXX SL3 application number
These five substrates or more cannot The set number exceeded

be used at the same time. the maximum number of
8085 -
usable communication
master boards.
Cannot use. NIF to exchange them The board other than NIF01-
8090 - NIF01-2 2 was used in the system
with the MEDAR board.
Abnormality is found in the power

∗ supply. Please confirm the connection
of the uniline.
8200
A fault is detected in the
0 power supply of the uniline
board.
ID overlaps. Please turn off power

8201 -
and confirm the rotary switch.
Abnormality is found in the substrate.

8202 - Please turn off power and confirm the
substrate.
8205 - ENABLE Unit over
IO module configuration is not

8210 -
modified
9-31
RE-CHO-A104
150133-1CD
10 LED Indicator on Circuit Board

10.1 LED Indicator on NCP 01 Circuit Board
LED Indicator on NCP 01 Circuit Board
The LED indicators: LED0/LED1 on the NCP01 circuit board show the statuses as in the
following table. The LED indicators show the operating statuses for the single NCP01 circuit
board.
LED0 KED1 Status
OFF OFF The power is not turned ON.
ON OFF Before the BIOS starts
OFF ON The BIOS starts.
ON ON The BIOS initialization has been

completed./OS boot starts.
CPU
TYPE JANCD-NCP01
DATE
REV
LED0 / LED1
LED
0 1
VIDEO
10-1
RE-CHO-A104
150133-1CD
10.2 LED Indicator on Robot I/F Unit
LED Indicator on Robot I/F Unit
The 7-segment LED indicator and battery alarm LED lamp are located on the robot I/F unit
(JZNC-NIF01o).
See " 10.3 7 SEG-LED Indicator " for details displayed by the 7-segment LED indicator.
The battery alarm LED lamp is lit when the battery runs out. See section 5.1.1 “Replacing
Parts of the CPU Unit” to replace the battery.
JZNC-
NIF 01o-1
Battery alarm
LED lamp PEV.
DS1
7-segment
LED indicator
S1
F1
F2
CN12
10-2
RE-CHO-A104
150133-1CD

10.3 7 SEG-LED Indicator
7 SEG-LED Indicator
The following tables show the operating statues for JANCD-NIF01/SGDR-AXA01/SGDR-

AXA02/JANCD-NCP02. The operating statuses are indicated by 7 SEG-LED.
[Normal Indication]
NX100
Status
NCP02 Circuit
NIF Circuit Board AXA Circuit Board
Board
Right after applying All 7-SEG indicators light up.

the power (‘8’, ‘+’, ‘.’ light up.)
During the start-up Counts up from ‘O’ toward ‘d’.

process
After starting up
‘d’, ‘+’, ‘.’ blink every one second.
normally
[Error Indication]
NX100
Status
NCP02 Circuit
NIF Circuit Board AXA Circuit Board
Board
Alarms occurrence The error cause is

in the Main CPU and indicated by 7 SEG-
servo CPU LED.
communication (See the indication
‘d’, ‘+’, ‘.’ blink every ‘d’, ‘+’, ‘.’ blink every
system spec 1 .)
one second. one second.
Normal alarms other
‘d’, ‘+’, ‘.’ blink every
than alarms
one second.
described above
Fatal alarms The error cause and the address where the error has occurred are
occurrence indicated by 7 SEG-LED.
(See the indication spec 2 .)
Indication Spec 1
SUPPLE
-MENT E.g.)
The cycle: [F] à [0] à [0] à [3] à [.] is repeated. : Error cause
10-3
RE-CHO-A104
150133-1CD
Indication Spec 2
E.g.)
[-] à [0] à [2] à [0] à [0] à : Error cause
The cycle: [,] à [-] à [0] à [0] à [0] à [0] à [F] à : Address where the error occurred
[F] à [0] à [4] is repeated.
n 7 SEG-LED Indicator Status (1-digit indication) of Each Unit

at Error Occurrence
NIF01
All Lit The power has been turned ON.
0 The booting program has started.
1 The system program has started. (Starts initialization of various kinds.)
2 Starts verifying the existence of other circuit boards. (Verifies the start-up of the
booting program.)
3 Starts the system program transmission.
4 Sends the request of the system program start-up.
5 Starts verifying the existence of other circuit boards. (Verifies the start-up of the
system program.)
6 Acquires hardware information, etc. of other circuit boards. (Verifies the IO
board status, servo IF, and so on.)
7 Starts the CMOS data transmission.
8 Sends the pre-online request.
9 Waits for CERF communication synchronization.
A
B Sends the start-up request of on-line system.
C The on-line system has started. (Starts up the initialization task.)
D Processes the NX100 setup completion. (Servo ON enabled)
E Alarm occurs at the NX100 setup.
F The maintenance system is starting up.
P Communications interrupted between NCP01 and the programming pendant.
U Updating system software through network.
10-4
RE-CHO-A104
150133-1CD

AXA01/AXA02
0 The booting program has started. (ROM/RAM/FP register check)
1 Starts the booting system. (Completes initialization of various kinds.)
2 Completes the preparation for receiving the system program.
3 The system program has been received. (Waits for the request of system
change.)
4 The system program has started. (Starts hardware initialization of various
kinds.)
5 Starts the system. (Completes initialization of various kinds.)
7 Receives the CERF mapping. (Waits for pre-online)
8 Starts the servo system. (Starts the process of various initialization.)
9 Waits for CERF communication synchronization. (Completes the process of
various initializations.)
A
B Waits for the start-up of on-line system.
C
D Completes the NX setup process. (Servo ON enabled)
NCP02
0 The booting program has started. (ROM/RAM/FP register check)
1 Starts the booting system. (Completes initialization of various kinds.)
2 Completes the preparation for receiving the system program.
3 The system program has been received. (Waits for the request of system
change.)
4 The system program has started. (Starts hardware initialization of various
kinds.)
5 Starts the system. (Completes initialization of various kinds.)
7 Receives the CERF mapping. (Waits for pre-online)
8 Starts the optional system. (Starts the process of various initialization.)
9
A
B
10-5
RE-CHO-A104
150133-1CD
NCP02
C
D Completes the NX setup process.
10-6
RE-CHO-A104
150133-1CD

n 7 SEG-LED Indicator Status (4 digit-indication) of Each Unit

at Error Occurrence
NIF01
0000 Arithmetic error
0001 Debug
0002 NMI
0003 Breakpoint
0004 Overflow
0005 Out of BOUND
0006 Invalid operation code
0007 Device disabled
0008 Double fault
0009 Coprocessor segment overrun
000A Invalid TSS
000B Segment absence
000C Stack segment fault
000D General protection exception
000E Page fault
000F
0010 Floating point error
0011 Alignment check
0012 Machine check
0013 SIMD floating point exception
0014
0015
0016
0017
0018
0019
001A
001B
001C
001D
001E
001F
10-7
RE-CHO-A104
150133-1CD
NIF01
0900 WDT error
AXA01/AXA02
0010 ROM error in the boot section
0020 RAM error
0030 FP register error
0040 On-line communications command error
0100 Reset exception
0200 Machine check exception
0210 WDT error
0300 Data access error
0400 Instruction access exception
0500
0600 Alignment exception
0700 Program exception
0800 Unavailable floating point exception
0900
0A00 Undefined exception
0B00 Undefined exception
0C00 System call exception
0D00 Trace exception
0E00 Undefined exception
0F00 Undefined exception
1000 Instruction conversion error exception
1100 Data load conversion error exception
1200 Data store conversion error exception
1300 Instruction breakpoint exception
1400 System management interruption
1500 Undefined exception
1C00 Undefined exception
1D00 Undefined exception
10-8
RE-CHO-A104
150133-1CD

AXA01/AXA02
3010 Receiving data size error
3020 Receiving data sum error
3030 Receiving data write address error
3040 All receiving data sum error
F001 Communication error with NIF01 (Send incompletion)
F002 Communication error with NIF01 (Receive incompletion)
F003 Communication error with NIF01 (Receive WDT)
F004 Communication error with NIF01 (Receive WDT inconsistency)
F010 Communication error with NIF01 (CERF status)
NCP02
0010 ROM error in the boot section
0020 RAM error
0030 FP register error
0040 On-line communications command error
0100 Reset exception
0200 Machine check exception
0210 WDT error
0300 Data access error
0400 Instruction access exception
0500
0600 Alignment exception
0700 Program exception
0800 Unavailable floating point exception
0900
10-9
RE-CHO-A104
150133-1CD
NCP02
0C00 System call exception
0D00 Trace exception
1000 Instruction conversion error exception
1100 Data load conversion error exception
1200 Data store conversion error exception
1300 Instruction breakpoint exception
1400 System management interruption
3010 Receiving data size error
3020 Receiving data sum error
3030 Receiving data write address error
3040 All receiving data sum error
10-10
RE-CHO-A104

Bang Ma Loi Robot Motoman Yaskawa nx100 Maintenance Manual

Uploaded by

Copyright:

Available Formats

Bang Ma Loi Robot Motoman Yaskawa nx100 Maintenance Manual

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Bang Ma Loi Robot Motoman Yaskawa nx100 Maintenance Manual

Uploaded by

Copyright:

Available Formats

150133-1CD

Alarm Code Alarm Level Alarm Reset Method

Level 0 (Major alarm) It is not possible to reset by "RESET"

Level 1 to 3 (Major alarm) It is not possible to reset by "RESET"

Level 4 to 8 (Minor alarm) After correcting the cause, it is possible to

Displaying and Releasing Alarm

Alarm No. ALARM 4100 [1] Sub-data

Main Menu Short Cut

Special Alarm Display

• XYZ coordinate data

• Control group data

n Multiple SERVOPACK System

n Independent Control Function (Optional)

Alarm Message List

Alarm Message List

Alarm Message List

Alarm Message List

Alarm Message List

Alarm Message List

Alarm Message List

Alarm Message List

Alarm Message List

Alarm Message List

Alarm Message List

Alarm Message List

Alarm Message List

Alarm Message List

Alarm Message List

Alarm Message List

Alarm Message List

Alarm Message List

Alarm Message List

Alarm Message List

Alarm Message List

SYSTEM ERROR 202∗ The status setting to base block is

Alarm Message List

Alarm Message List

Alarm Message List

Alarm Message List

Alarm Message List

Alarm Message List

Alarm Message List

Alarm Message List

60: Error due to unmatched output

Alarm Message List

Alarm Message List

Alarm Message List

Alarm Message List

Alarm Message List

Alarm Message List

Alarm Message List

Alarm Message List

Alarm Message List

Alarm Message List

Alarm Message List

Alarm Message List

Alarm Message List

Alarm Message List

51 An error occurred when the request