Renaissance Middle School Control Submittal 05-20-2022

TITLE PAGE
RENAISSANCE MIDDLE SCHOOL

176 N FULLERTON AVE, MONTCLAIR, NJ 07042
FACILITY MONTCLAIR SCHOOL DISTRICT PROJECT: RENAISSANCE MIDDLE SCHOOL

CLIENT
AME INC. 1275 Bloomfield Ave.
Fairfield, NJ 07004
Building Automation and TITLE PAGE
ENGINEER 0 05-20-2022 SUBMITTED FOR APPROVAL SK (T) 973-884-4100
Temperature Control
(M) 973-214-6886
ARCHITECT # DATE REVISION DESCRIPTION BY Specialists JOB #: 21-08986 PAGE: 1 of 44
TABLE OF CONTENT
PAGE NO TITLE REV
1 TITLE PAGE
2 TABLE OF CONTENT
3 LEGEND & SYMBOLS
4 NETWORK RISER
5 DEVICE INSTANCES
6 GROUND FLOOR PLAN
7 FIRST FLOOR PLAN
8 SECOND FLOOR PLAN
9 HWS SCHEMATIC DIAGRAM
10 COMMUNICATION WIRING DIAGRAM
11 HWS WIRING DIAGRAM
12 HWS SEQUENCE OF OPERATION
13 HWS BILL OF MATERIAL
14 HWS PANEL LAYOUT
15 AHU SCHEMATIC DIAGRAM
16 AHU WIRING DIAGRAM
17 AHU SEQUENCE OF OPERATION
18 AHU BILL OF MATERIAL
19 AHU PANEL LAYOUT
20 GYM AHU SCHEMATIC DIAGRAM
21 GYM AHU WIRING DIAGRAM
22 GYM AHU SEQUENCE OF OPERATION PAGE 1
23 GYM AHU SEQUENCE OF OPERATION PAGE 2
24 GYM AHU BILL OF MATERIAL
25 UV SCHEMATIC DIAGRAM
26 UV WIRING DIAGRAM
27 UV SEQUENCE OF OPERATION PAGE 1
28 UV SEQUENCE OF OPERATION PAGE 2
29 UV BILL OF MATERIAL
30 STEAM RADIATOR SCHEMATIC DIAGRAM
31 STEAM RADIATOR W/INLINE FAN SCHEMATIC DIAGRAM
32 RADIATOR TYPE-1 WIRING DIAGRAM PAGE 1
36 RADIATOR TYPE-3 WIRING DIAGRAM
37 RADIATOR BILL OF MATERIAL
38 RADIATOR TYPE-1 & 2 PANEL LAYOUT
39 RADIATOR TYPE-3 PANEL LAYOUT
40 TRV SCHEMATIC DIAGRAM
41 VALVE SCHEDULE PAGE 1
44 MASTER BILL OF MATERIAL

CLIENT
Fairfield, NJ 07004
Building Automation and TABLE OF CONTENT
Temperature Control
(M) 973-214-6886
LEGEND & SYMBOLS
GENERAL NOTES HVAC SYSTEM LEGEND:

M
1. ALL POWER WIRING 120 VAC AND ABOVE BY ELECTRICAL CONTRACTOR.
FRZ
MOTOR OPERATED DAMPER FREEZESTAT (D.P. CONTACT)
TEMPERATURE CONTROL LEGEND:
PH DAT
MOUNTED ON PANEL FACE
CONTROL VALVE, 2-WAY PREHEAT COIL DUCT MOUNTED TEMPERATURE
MOUNTED INSIDE PANEL C SENSOR
CONTROL VALVE, 3-WAY
3 CONTROL TUBE #3 C
PARALLEL BLADED DAMPER
PNEUMATIC TUBING COOLING COIL IS
OPPOSED BLADED DAMPER C
WIRING IMMERSION TYPE
RH TEMPERATURE SENSOR
6 TERMINAL BLOCK #6 AB SIGNAL LINE INSIDE PANEL
REHEAT COIL
SV C
DSD
SOLENOID VALVE H DUCT MOUNTED
SMOKE DETECTOR
HEATING COIL
C SPT
ABBREVIATIONS: STATIC PRESSURE
H L TRANSMITTER
DIRECT EXPANSION COIL
AFMS- AIR FLOW MEASURING STATION OA -OUTSIDE AIR
C- COMMON PORT OL'S- MOTOR STARTER OVERLOADS
SP
CCP- CENTRAL CONTROL PANEL PC- PRESSURE CONTROLLER STEAM PRESSURE SENSOR
FAN
CR- CONTROL RELAY PE- PRESSURE TOGGLE SWITCH
CS- CURRENT SWITCH PI- PRESSURE INDICATOR
DA-DAMPER ACTUATOR PL- PILOT LIGHT
MANUAL VALVE HUM
DPRO- DAMPER OUTPUT PR- PNEUMATIC RELAY DUCT MOUNTED
DPRS- DAMPER STATUS HUMIDITY SENSOR
PT- PRESSURE TRANSMITTER
DPS- DIFFERENTIAL PRESSURE SWITCH RC- RECEIVER CONTROLLER
DPT- DIFFERENTIAL PRESSURE TRANS RR- REVERSING RELAY ZONE CO2 SENSOR
EA- EXHAUST AIR RT- ROOM THERMOSTAT
ES- END SWITCH, POSITION SWITCH S- SWITCH
FS- FLOW SWITCH SD- SMOKE DETECTOR SPACE TEMPERATURE
FM
FSD- FIRE & SMOKE DAMPER S/W- SUMMER/ WINTER SIGNAL WATER FLOW METER
H- HUMIDISTAT T- THERMOSTAT
HC- MOTOR STARTER HOLDING COIL TS- TEMPERATURE SENSOR
HI- HUMIDITY INDICATOR TC- TIME CLOCK MAT
HL- HIGH LIMIT HUMIDISTAT TDR- TIME DELAY RELAY AVERAGING TYPE
OUTSIDE AIR CO2 SENSOR
HS- HIGH SIGNAL SELECTOR TEMPERATURE SENSOR
THL- TEMPERATURE HIGH LIMIT THERMOSTAT
HT- HUMIDITY TRANSMITTER TI- TEMPERATURE INDICATOR
LCP- LOCAL CONTROL PANEL TLL- TEMPERATURE LOW LIMIT THERMOSTAT
LS- LOW SIGNAL SELECTOR TR- TRANSDUCER
MA- MIXED AIR TT- TEMPERATURE TRANSMITTER FILTER AIR FLOW MEASURING STATION
MOD-MOTER OPERATED DAMPER TX- TRANSFORMER
NC- NORMALLY CLOSED V- VALVE
NCP- NETWORK CONTROL PANEL WB- WET BULB
NO- NORMALLY OPEN FIRE & SMOKE DAMPER
WU- WARM-UP SIGNAL
(BY OTHERS) CR-1
C
CONTROL RELAY
OAT
OUTSIDE AIR TEMPERATURE SENSOR
CS
CURRENT SENSOR
WIRING LEGEND
Low Voltage, 18 AWG, Copper Wire
NO CO2 CO2 SENSOR

UL Listed Low Voltage Communication Wiring, 1 Twisted Pair
NC
22/2 AWG, Shielded Copper Wire, Low Capacitance Plenum
PVC Cable, GENESIS P/N: 3251, WINDY CITY P/N: 043004AL C LEAK DETECTOR
Line Voltage, THHN Field Wiring
CAT5e Cable

CLIENT
Fairfield, NJ 07004
Building Automation and LEGEND & SYMBOLS
Temperature Control
(M) 973-214-6886
NETWORK RISER
CP-5
EOL
PUB6438SR
RAD TYPE-2 PANEL
2ND FLOOR
CP-4 CP-3
PUB6438S PUB6438SR PUB6438S PUB6438S
RAD TYPE-3 PANEL RAD TYPE-1 PANEL AHU AHU
1ST FLOOR
CP-1 CP-2
MS/TP TRUNK-1
PUB6438S PUB6438S PUB6438S PUB6438S PUB6438S PUB6438S PUB6438S PUB6438S PUB6438S
HWS UV-1 UV-2 UV-3 UV-4 UV-5 UV-6 AHU UV-7

CAT6
JACE-1
WEB-8000
Module: 8000
TO DISTRICT IP Address: x.x.x.x
SERVER Subnet: 255.255.255.0
Gateway: 0.0.0.0
Device Instance:200000
Location: BOILER ROOM
GROUND FLOOR

CLIENT
Fairfield, NJ 07004
Building Automation and NETWORK RISER
Temperature Control
(M) 973-214-6886
DEVICE INSTANCES
RENAISSANCE MIDDLE SCHOOL

DEVICE COUNT UNIT TAG/EQUIPMENT PANEL CONTROLLER FLOOR DI MAC ADDRESS
1 JACE - 1 CP-1 WEB-8000 GROUND FLOOR 200000 00
MS/TP TRUNK - 1
2 HWS CP-1 PUB6438S GROUND FLOOR 200101 01
3 UV-1 - PUB6438S GROUND FLOOR 200102 02
9 AHU CP-2 PUB6438S GROUND FLOOR 200108 08
11 AHU - PUB6438S FIRST FLOOR 200110 10
12 AHU - PUB6438S FIRST FLOOR 200111 11
13 RAD TYPE-1 PANEL CP-3 PUB6438SR FIRST FLOOR 200112 12
14 RAD TYPE-3 PANEL CP-4 PUB6438S FIRST FLOOR 200113 13
15 RAD TYPE-2 PANEL CP-5 PUB6438SR SECOND FLOOR 200114 14

CLIENT
Fairfield, NJ 07004
Building Automation and DEVICE INSTANCES
Temperature Control
(M) 973-214-6886
GROUND FLOOR PLAN
FTR-1
UV-2
UV-3
UV-1
UV-4
HWS
AHU
UV-7 UV-6 UV-5

CLIENT
Fairfield, NJ 07004
Building Automation and GROUND FLOOR PLAN
Temperature Control
(M) 973-214-6886
FIRST FLOOR PLAN
AHU AHU
TRV-13 TRV-14
TRV-11 TRV-5 FTR-6 FTR-5

TRV-4
RWF-2 TRV-12
TRV-10 TRV-2
TRV-7 TRV-3
TRV-6
TRV-9
RWF-1
RWF-3 RWF-4
TRV-8
FTR-4 FTR-3 FTR-2 TRV-1

CLIENT
Fairfield, NJ 07004
Building Automation and FIRST FLOOR PLAN
Temperature Control
(M) 973-214-6886
SECOND FLOOR PLAN
TRV-15 TRV-17 TRV-16

RWF-5
FTR-8 FTR-7
RWF-10 RWF-9 RWF-8 RWF-7 RWF-6

CLIENT
Fairfield, NJ 07004
Building Automation and SECOND FLOOR PLAN
Temperature Control
(M) 973-214-6886
HWS SCHEMATIC DIAGRAM
HWP-1
OA-T
OUTSIDE TEMPERATURE SENSOR
UI-5 C1
CS-1
AO-1
T3
T4
C1 UI-3
T+ UI-1
X
T- C1 2 1 3 DO-1 T
S/S
X
C1
*INSTALL SENSOR TO
HWS
THE NORTH SIDE OF LPS STARTER TS-1
V-#
OUTSIDE WALL HX-1 PANEL
*OUTSIDE AIR TEMPERATURE

TO BE SHARED GLOBALLY
HWP-2
CONDENSATE
UI-6
CS-2
SIO1
X
DO-2
S/S
X
C1
C1
STARTER
UI-4
PANEL
T
UI-2
C1 HWR
TS-2
SP
LPS TO
BUILDING
EQUIPMENTS
BLR-1 BLR-2
LPS LPS
X X
DI-1 X DO-3 DI-2 X DO-4
STS
STS
S/S
S/S
X X
C1 X C1 C1 X C1
DI-3 X DI-4 X
ALM
ALM
C1 X C1 X
BOILER-1 BOILER-2
PANEL PANEL

CLIENT
Fairfield, NJ 07004
Building Automation and HWS SCHEMATIC DIAGRAM
Temperature Control
(M) 973-214-6886
COMMUNICATION WIRING DIAGRAM
120 VAC
BY OTHERS 24VAC 24VAC
OUTPUT OUTPUT
CP-1 ø N
1 2 3 4 5 6 7 8 9
PSH-1 TR-1
H 24VAC
H N T1 T2 T3 T4 H T3
N
N COM
T4
COM
T2
24 VAC
T1
JACE-1
T1
24VAC/DC
WLAN
T2
-
ACC
24V DC
OFF
CLT
+
END
BIA
MID
DATA BUS SHIELDS: CONNECT TO
NS-1 THE ‘S’ TERMINAL AND GROUND
A-
BACNET MS/TP TO
RS485-A
WEB-8000
A+ FIELD CONTROLLERS
SH
PRI
B-
BACNET MS/TP TO
FIELD CONTROLLERS
RS485-B
B+
SH
SEC
FROM OWNER’S END
BIA
IT INFRASTRUCTURE MID
PANEL CONTINUED ON NEXT PAGE
LOCATION : BOILER ROOM

CLIENT
Fairfield, NJ 07004
Building Automation and COMMUNICATION WIRING DIAGRAM
Temperature Control
(M) 973-214-6886
HWS WIRING DIAGRAM
CP-1
C1
CS-2 42
HWP-2 STATUS
41 C4
CS-2
CS-1 40 40 UI-6 COM 20
HWP-1 STATUS
39 C4 C4 39 COM DO-8 19
38 CS-1
TS-2 38 UI-5 DO-7 18
T
TS-2 HW RETURN TEMPERATURE C3

37 TS-2
37 UI-4
COM 17
TS-1 36 PUB6438S
T
TS-1 HW SUPPLY TEMPERATURE C3 36 COM

35 C3 DO-6 16
TS-1 WHT/YEL FR-4 ORG
35 UI-3 C5 17 X BOILER
S/S
34 C BLR-2 S/S
DO-5 15 WHT/BLU YEL
X PANEL
VOUT BLR-2 START/STOP
SP-1 SP-1 16
SP
COM 33 C2 34 UI-2
STEAM PRESSURE SENSOR COM 14 C5
V+
32 DC+ C2 BLR-2 S/S WHT/YEL
33 COM C5 15 FR-3 ORG
X
DO-4 13 BOILER BLR-1 S/S
S/S
C
WHT/BLU YEL PANEL BLR-1 START/STOP
OAT X
31 C2 32 UI-1 BLR-1 S/S 14
OAT DO-3 12
OUTSIDE AIR TEMPERATURE
30
DC+ 31 20VDC COM 11 C4 WHT/YEL FR-2 ORG
C4 13 X PUMP HWP-2 S/S
S/S
C
BLR-2 ALM HWP-2 S/S WHT/BLU YEL PANEL HWP-2 START/STOP
X 29 X
ALM
BLR-2 ALM BOILER 30 DI-4 DO-2 10 12

BOILER-2 ALARM PANEL X
PUB6438S
28 C1 BLR-1 ALM HWP-1 S/S
Enhanced
Spyder™
29 DI-3 DO-1 9
WHT/YEL FR-1 ORG
27 C4 11 X PUMP HWP-1 S/S
S/S
BLR-1 ALM X
ALM
BOILER C
Sylk™
C1 28 COM WHT/BLU YEL PANEL HWP-1 START/STOP
BOILER-1 ALARM PANEL X X
26 C1 10
BLR-2 STS
27 DI-2
BLR-2 STS X 25 FROM
STS
BOILER
BOILER-2 STATUS PANEL X BLR-1 STS PREVIOUS
24 C1 26 DI-1
BACNET
BAC- 8
23 DEVICE
X
STS
BLR-1 STS BOILER 25 COM

BOILER-1 STATUS PANEL X BAC+ 7 TO NEXT
22 C1
BACNET
24 AO-3 DEVICE
SBUS2 6
23 AO-2
SBUS1 5
22 COM
21 T3
HX-1 VLV CTRL (V-1) HX-1 HW VLV CTRL SHLD 4
2 21 AO-1
HX-1 HW VALVE 20 T4
1 EGND 3
CONTROL (V-1)
3 19
24VAC T4
COM 2
24VAC 1 T3
LOCATION : BOILER ROOM

CLIENT
Fairfield, NJ 07004
Building Automation and HWS WIRING DIAGRAM
Temperature Control
(M) 973-214-6886
HWS SEQUENCE OF OPERATION
1.1 STEAM HEATING SYSTEM SEQUENCE:

A. STEAM BOILER RUN CONDITIONS:
1.THE STEAM BOILER SHALL BE ENABLED TO RUN WHENEVER OUTSIDE AIR TEMPERATURE IS LESS THAN 60°F (ADJUSTABLE), ANY HEATING EQUIPMENT IS IN THE OCCUPIED MODE, AND THERE IS A CALL FOR HEAT FROM
ANY PIECE OF EQUIPMENT (TOTAL NUMBER OF ZONE HEATING VALVES, WHICH ARE OPEN MORE THAN 20%, IS GREATER THAN THE USER ADJUSTABLE SET POINT OF #4 .
2.THE STEAM BOILERS SHALL ALSO BE ENABLED WHEN THE OUTSIDE TEMPERATURE IS LESS THAN THE FREEZE PROTECTION SET POINT OF 38 °F (ADJ.) OR ANY ZONE TEMPERATURE IN THE BUILDING FALLING BELOW THE
UNOCCUPIED SET POINT OF 55 °F (ADJ.)
3.TO PREVENT SHORT CYCLING, STEAM BOILERS SHALL RUN FOR AND BE OFF FOR MINIMUM ADJUSTABLE TIMES (BOTH USER DEFINABLE), UNLESS SHUTDOWN ON SAFETIES OR OUTSIDE AIR CONDITIONS. IMPLEMENT
LOW-FIRE HOLD SEQUENCE DURING LOW LOAD CONDITIONS TO PREVENT SHORT CYCLING.
4.EACH BOILER SHALL RUN SUBJECT TO ITS OWN INTERNAL SAFETIES AND CONTROLS.
B. BOILER LEAD/LAG OPERATION:

1.THE BOILERS SHALL OPERATE IN A LEAD/LAG FASHION WHEN CALLED TO RUN
a. THE LEAD BOILER SHALL RUN FIRST
b. ON FAILURE OF THE LEAD BOILER, THE LAG BOILER SHALL RUN AND THE LEAD BOILER SHALL TURN OFF.
c. THE LAG BOILER SHALL ENABLE WHEN THE HEATING DEMAND IS GREATER THAN 85 % FOR 5 MINUTES. THE LAG BOILER SHALL DISABLE WHEN THE HEATING DEMAND IS LESS THAN THE 50 %.
2.THE DESIGNATED LEAD BOILER SHALL ROTATE WEEKLY.
3.ALARMS SHALL BE PROVIDED AS FOLLOWS:
a. BOILERS: THE LEAD BOILER IS IN FAILURE AND THE STANDBY BOILER IS ON.
C. STEAM PRESSURE SETPOINT:

1.THE STEAM PRESSURE SETPOINT SHALL BE PROGRAMMED ON AN AUTOMATIC RESET SCALE BASED ON THE OUTSIDE AIR TEMPERATURE
a. OUTSIDE AIR TEMPERATURE OF 20°F (ADJUSTABLE) – STEAM PRESSURE SETPOINT OF 7 PSI (ADJUSTABLE)
b. OUTSIDE AIR TEMPERATURE OF 60°F (ADJUSTABLE) – STEAM PRESSURE SETPOINT OF 3 PSI (ADJUSTABLE)
D. ALARMS SHALL BE PROVIDED AS FOLLOWS, ONLY WHEN THE HEATING SYSTEM IS ENABLED:
1.LOW STEAM PRESSURE – IF LESS THAN 2 PSI (ADJUSTABLE) FOR MORE THAN 30 MINUTES.
1.2 HEATING HOT WATER SYSTEM STEAM TO HOT WATER HEAT EXCHANGER:
A.THE HEATING HOT WATER SYSTEM CONSISTS OF A STEAM TO HOT WATER SHELL AND TUBE HEAT EXCHANGER WITH STEAM CONTROL VALVE AND HOT WATER CIRCULATION PUMPS.
B.SYSTEM ON/OFF AND PUMP CONTROL:

1.THE HEATING SYSTEM SHALL BE OPERATED BY THE BUILDING MANAGEMENT SYSTEM (BMS) AND SHALL OPERATE WHENEVER THE OUTSIDE AIR TEMPERATURE IS LESS THAN 60°F (ADJUSTABLE), THE BUILDING IS IN
OCCUPIED MODE, AND THERE IS A CALL FOR HEAT FROM ANY PIECE OF EQUIPMENT. THE HOT WATER PUMP LEAD/LAG POSITION SHALL BE ALTERNATED ON A WEEKLY BASIS.
2.WHEN HOT WATER IS REQUIRED, THE LEAD HEATING HOT WATER PUMP SHALL BE STARTED. THE PUMPS WILL BE OPERATED ON/OFF AS REQUIRED TO MAINTAIN TEMPERATURE SET POINT.
3.BOTH PUMPS SHALL BE STAGED OFF DURING THE UNOCCUPIED HOURS. IF THERE IS A CALL FOR HEAT WITHIN THE BUILDING THE LEAD PUMP SHALL BE ENABLED. THE PUMPS SHALL FOLLOW THE SAME UNOCCUPIED
OAT LOCKOUT AS THE BOILERS.
4.WHEN HOT WATER IS NOT REQUIRED THE STEAM CONTROL VALVE FOR THE STEAM TO HOT WATER HEAT EXCHANGER SHALL BE CLOSED. THE PUMPS SHALL REMAIN RUNNING FOR 2 MINUTES (ADJUSTABLE) TO
DISSIPATE RESIDUAL HEAT IN THE HEAT EXCHANGER AND THEN THE PUMPS SHALL BE SHUT OFF.
C.TEMPERATURE CONTROL – NORMAL OPERATION:

1.THE HOT WATER SYSTEM SHALL MAINTAIN A HEATING HOT WATER SUPPLY TEMPERATURE SETPOINT BASED ON OUTSIDE AIR TEMPERATURE. PRIOR TO OPENING THE STEAM CONTROL VALVES FOR THE STEAM TO HOT
WATER HEAT EXCHANGER, HOT WATER FLOW SHALL BE VERIFIED BY CHECKING THE CURRENT TRANSDUCER FOR EACH PUMP MOTOR. IF THERE IS NO CURRENT FLOW TO THE PUMP MOTOR, THEN THE STEAM CONTROL
VALVES SHALL REMAIN CLOSED.
2.UPON PROOF OF FLOW, THE STEAM CONTROL VALVE SHALL BE MODULATED OPEN TO MAINTAIN THE SETPOINT TEMPERATURE. IF THE HEATING HOT WATER SUPPLY TEMPERATURE RISES ABOVE THE SETPOINT, THE
STEAM CONTROL VALVE SHALL BE MODULATED CLOSED TO MAINTAIN THE SETPOINT TEMPERATURE. ALL VALVES SHALL BE OPENED AND CLOSED SLOWLY.
3.DURING THE MORNING WARMUP SEQUENCE (4:00 AM TO 9:00 AM (ADJ.)), THE SYSTEM WILL IMPLEMENT A MORNING HOT WATER BOOST SEQUENCE WHICH WILL SET THE HOT WATER SETPOINT TO 180°F WHEN THE OAT
IS LESS THAN 35°F (ADJUSTABLE). AFTER THE MORNING BOOST IS OVER, THE HOT WATER SETPOINT WILL RETURN TO ITS NORMAL HOT WATER RESET SEQUENCE.
4.DURING UNOCCUPIED MODE, THE HOT WATER SUPPLY TEMPERATURE SETPOINT SHALL BE CALCULATED BASED ON OUTSIDE AIR TEMPERATURE WITH AN OFFSET INITIALLY SET AT -40°F (ADJUSTABLE).

CLIENT
Fairfield, NJ 07004
Building Automation and HWS SEQUENCE OF OPERATION
Temperature Control
(M) 973-214-6886
HWS BILL OF MATERIAL
HOT WATER SYSTEM BILL OF MATERIAL

Item # Application Tag Part No. Quantity Description Manufacturer
1 JACE JACE-1 WEB-8000 1 Base unit includes two isolated RS485 ports, two 10/100MB Ethernet ports, USB Backup & Restore and WiFi connectivity Honeywell
2 Device License Device NC-8025 1 Up to 25 devices/1250 point core Honeywell
3 SMA SMA SSMA-8025-1YR-INIT 1 One Year Software Maintenance Agreement for 8025 Core (18 month initial period only) Honeywell
4 Network Switch NS-1 EISK5-100T 1 5 Ports 10/100 Mbps Skorpion switch. Contemporary Controls
5 Programmable Controller C-1 PUB6438S 1 Honeywell Spyder Controller with 6UI, 4DI, 3AO, 8DO Honeywell
6 Outside Air Temperature OAT A/20K-O-4X 1 OA Temp, 20k temp. NEMA 4x ACI
7 Immersion Temp Sensor TS-# A/20K-I-2.5"-GD 2 20K Ohm Thermistor, Immersion, 2.5", Galvanized Enclosure ACI
8 Steam Pressure Transmitter SP 626-08-CB-P1-E5-S5 1 Pressure Transmitter, 0-10VDC, 3 wire, 0-30 psig, 1/4" NPT male process connection Dwyer
9 Stainless Steel Siphons - A-170-A 1 1/4" NPT male, both side, Siphon, SS Dwyer
10 Stainless Steel Fitting - A-2021-2 1 1/4" NPT female connection both side for connecting siphon and pressure transmitter Dwyer
11 Current Switch CS-# C-2300 2 Split core, Adj. trip, Min trip at 0.5 A, status output N.O. 1.0 A @ 30VAC/DC Senva
12 Field Mount Relay FR-# RIBU1C 4 Universal RIB Relay Functional Devices
13 Power Supply for JACE PSH-# PSH75AB10 1 Enclosed Single 75VA, 120 to 24 Vac, UL Class 2 Power Supply, 10Amp main breaker Functional Devices
14 Transformers TR-# 10051MWCB 1 96 VA 120-208-240, 277-480V Pri. -24V Sec Multi-tap Class 2 Transformer Senva
15 Panel CP-1 SCE-24N2406LP 1 24"H X 24"W X 6" Depth NEMA-1 Enclosure, steel ANSI61-Grey Saginaw
16 Perforated Subpanel CP-1 SCE-24N24MP 1 Subpanel, NEMA-1 Saginaw
17 Terminal Blocks TB - 42 - To be procured on site
* REUSE EXISTING SENSORS & END DEVICES WHEREVER POSSIBLE. EXISTING PIPE LINE SIZES ARE NOT AVAILABLE. FIELD TO COORDINATE THE LENGTH OF THE PROBE FOR IMMERSION SENSORS PRIOR TO ORDERING NEW.

CLIENT
Fairfield, NJ 07004
Building Automation and HWS BILL OF MATERIAL
Temperature Control
(M) 973-214-6886
HWS PANEL LAYOUT
CP-1
CP-1 1"
END
END
SH
SH
MID
MID
A+
B+
BIA
BIA
A-
B-
- +
24VAC/DC 24V DC RS485-A RS485-B
42
41
40
39
4.5"
38
WEB-8000
PRI SEC
ACC
OFF
CLT
WLAN
7"
1"
21 AO-1
22 COM
23 AO-2
24 AO-3
25 COM
26 DI-1
27 DI-2
28 COM
29 DI-3
30 DI-4
31 20VDC
32 UI-1
33 COM
34 UI-2
35 UI-3
36 COM
37 UI-4
38 UI-5
39 COM
40 UI-6
24" 22" 1" 1.5"
1"
5.5"
Spyder™
PUB6438S
Sylk™
Enhanced
SBUS1
SBUS2
24VAC
24VAC
EGND
SHLD
BAC+
BAC-
DO-1
DO-2 10
DO-3 12
DO-4 13
DO-5 15
DO-6 16
DO-7 18
DO-8 19
COM
COM 11
COM 14
COM 17
COM 20
1
2
3
4
5
6
7
8
9
7"
1"
13
12
3" 11
10
9
PSH 8
NS-1 7
4.5"
6
TR-1 5
4"
4
3
2 120VAC
1 N
ø (BY
OTHERS)
5.2"
2"
24" 22"
NOTES :
1. PANEL LAYOUTS ARE NOT TO THE SCALE.

CLIENT
Fairfield, NJ 07004
Building Automation and HWS PANEL LAYOUT
Temperature Control
(M) 973-214-6886
AHU SCHEMATIC DIAGRAM
ZONE TEMP SENSOR
UI-2 SEN+
C1 SEN-
UI-1 SET
C1 SET
ZN-T
ZONE TEMPERATURE SENSOR
AO-2
T1
T2
C1
FOR INTERLOCK. C1
DI-2
UI-3
3
2
1
FILTER STEAM COIL FRZ SUPPLY FAN DAT
OUTSIDE SUPPLY
NC
AIR AIR
C
OAD DI-1
X T1 C1
V-# X T2
X
X
AO-1 C1
S/S
X
DO-1
STARTER
COND. LPS PANEL
AHU SCHEDULE
ITEM# TAG FLOOR LOCATION
1 AHU GROUND FLOOR G-14 MECH

CLIENT
Fairfield, NJ 07004
Building Automation and AHU SCHEMATIC DIAGRAM
Temperature Control
(M) 973-214-6886
AHU WIRING DIAGRAM
120 VAC
BY OTHERS 24VAC
ø N OUTPUT
CP-2
1 2 3 4 5 6
TR-1
24 VAC
H N H T1
T2
T1 N COM
T2
C1
40 UI-6 COM 20
39 COM DO-8 19
38 UI-5 DO-7 18
37 UI-4
COM 17
DAT 28 C3
PUB6438S
DAT
DISCHARGE AIR C3 36 COM

TEMPERATURE 27 DO-6 16
DAT
35 UI-3
DO-5 15
ZN-T
SEN- 26 34 UI-2
ZNT COM 14
ZONE TEMPERATURE SEN+
25 C2 C2 33 COM
SENSOR SET DO-4 13
SET 24 ZN-T SP
32 UI-1 C4 WHT/YEL FR-2 BLU
10 X SF- SFTY
SFTY
DO-3 12 C
FAN PANEL
23 C2 WHT/BLU YEL SF SAFETY
X
9
31 20VDC COM 11 C4
SF SFTY
30 DI-4 DO-2 10 WHT/YEL FR-1 ORG
C4 8 X SF- S/S
S/S
PUB6438S
22 WHT/BLU
C
YEL FAN PANEL
SF S/S
Enhanced
X SF START/STOP
Spyder™
29 DI-3 DO-1 9
FRZ
FRZ STAT 7
21 C1
FREEZESTAT ALARM
Sylk™
C1 28 COM
20 T1
FRZ STAT
19 27 DI-2
FROM
CS-1 26 DI-1 PREVIOUS
18 C1 BACNET
CS-1 BAC- 8 DEVICE
SUPPLY FAN STATUS 17 25 COM
BAC+ 7 TO NEXT
BACNET
24 AO-3 DEVICE
3 16 SBUS2 6
ECON DMPR CTRL ECON DMPR CTRL
2 23 AO-2
ECON DAMPER CONTROL 15 T2
1 SBUS1 5
14 22 COM
SHLD 4
STM VLV CTRL
21 AO-1
EGND 3
13
x 24VAC T2
12 T2 COM 2
STM VLV CTRL
x
STEAM VALVE CONTROL
x 11 24VAC 1 T1
LOCATION : G14 MECH
NOTES :
1. VERIFY AND REUSE EXISTING FREEZSTAT INTERLOCK
WIRING, IF FOUND IN WORKING CONDITION.

CLIENT
Fairfield, NJ 07004
Building Automation and AHU WIRING DIAGRAM
Temperature Control
(M) 973-214-6886
AHU SEQUENCE OF OPERATION
A. SCHEDULING: THE SCHEDULE WILL BE COMMUNICATED TO THE UNIT’S BACNET MS/TP DDC CONTROLLER AS ESTABLISHED IN THE GUI. THE UNIT WILL REMAIN IN THE “UNOCCUPIED” MODE UNTIL THE
SUPPLY FAN CURRENT SWITCH (SFCS) HAS PROVEN THE SUPPLY FAN “ON”.
B. SPACE TEMPERATURE SENSOR (RMT):
THE SPACE TEMPERATURE SENSOR (RMT) WILL HAVE A LOCALLY ADJUSTABLE HEATING SETPOINT WITH AN OVERRIDE PUSHBUTTON; WHEN THE BUTTON IS DEPRESSED, THE LED WILL LIGHT & THE UNIT WILL BE
SCHEDULED INTO THE “OCCUPIED” MODE FOR UP TO 3 HOURS (ADJ.); UPON THE EXPIRATION OF THE OVERRIDE, THE UNIT WILL REVERT TO ITS SCHEDULED MODE. THE SPACE HEATING (HSP/UHSP)WILL BE CONTROLLED
FROM THE GUI. THE SETPOINTS WILL BE INITIALLY SET AT 72 °F (ADJ.) FOR HEATING (HSP) WITH A SETPOINT ADJUSTMENT SPAN SETTING OF ± 4 °F (ADJ.).
C. “UNOCCUPIED” MODE:
WHEN THE UNIT IS SCHEDULED IN THE “UNOCCUPIED” MODE; THE UNIT’S SUPPLY FAN (SFSS), THE OUTSIDE DAMPERS (OAD) WILL BE “CLOSED”; WHEN THE OUTSIDE AIR TEMPERATURE (OAT) IS > 45 °F, THE STEAM
CONTROL VALVE BE “CLOSED” TO THE COIL. WHEN THE OUTSIDE AIR TEMPERATURE (OAT) IS < 48 °F, THE STEAM CONTROL VALVE WILL MODULATE TO MAINTAIN A DISCHARGE AIR SETPOINT (DASP) OF 85 °F.
D. “UNOCCUPIED COOLING” MODE: NONE
E. “UNOCCUPIED HEATING” MODE:
WHEN ANY SPACE TEMPERATURE SENSOR (RMT) IS < THE “UNOCCUPIED HEATING” SETPOINT (UHSP) OF 60 °F (ADJ.), THE UNIT’S SUPPLY FAN (SFSS) WILL BE COMMANDED “ON”. WHEN THE SPACE TEMPERATURE (RMT)
IS > THE “UNOCCUPIED HEATING” SETPOINT (UHSP) HYSTERESIS, THE UNIT’S SUPPLY FAN (SFSS) WILL BE COMMANDED “OFF”.
F. “OCCUPIED” MODE:
WHEN THE UNIT IS SCHEDULED IN THE “OCCUPIED” MODE THE UNIT SUPPLY FAN (SFSS) WILL BE COMMANDED “ON” & RUN CONTINUOUSLY. THE OUTSIDE AIR (OAD) DAMPER WILL “OPEN” TO THE MINIMUM OUTSIDE AIR
SETTING (ADJ.) (OAMINSP). UPON THE TRANSITION OF THE UNIT TO “OCCUPIED” MODE, A 10 MINUTE RAMP WILL BE IMPLEMENTED BEFORE THE OUTSIDE DAMPERS (OAD) CAN GO FULLY OPEN.
G. “MORNING WARM-UP” MODE:
THE UNIT WILL BE PLACED IN “WARM-UP” MODE WHEN THE SPACE TEMPERATURE (RMT) IS > 5 °F (ADJ.) BELOW THE SPACE HEATING SETPOINT (HSP). WHEN THE UNIT IS PLACED IN WARM-UP MODE THE OUTSIDE AIR
(OAD) DAMPERS WILL BE “CLOSED”. THE STEAM CONTROL VALVE WILL BE MODULATED “OPEN” TO THE COIL TO MAINTAIN A DISCHARGE AIR SETPOINT (DASP) OF 85 °F (ADJ.). THE UNIT WILL BE RELEASED FROM
“WARM-UP” MODE WHEN THE SPACE TEMPERATURE (RMT) IS < 2 °F (ADJ.) BELOW THE SPACE HEATING SETPOINT (HSP). WHEN THE UNIT IS RELEASED FROM WARM-UP MODE THE OUTSIDE AIR (OAD), THE STEAM
CONTROL VALVE WILL REVERT TO THEIR SCHEDULED MODE.
H. MINIMUM OUTSIDE AIR CONTROL:
THE TESTING & BALANCING CONTRACTOR (TAB) WILL ADJUST & SET THE OUTSIDE AIR MINIMUM SETTING (OAMINSP). THE OUTSIDE AIR (OAD) DAMPERS WILL POSITION ACCORDING TO THE SEQUENCE OF OPERATIONS.
I. “HEATING” MODE:
THE STEAM CONTROL VALVE WILL MODULATE TO MAINTAIN THE SPACE TEMPERATURE (RMT) AT OR ABOVE THE SPACE HEATING SETPOINT (HSP). WHEN THE SPACE TEMPERATURE (RMT) IS < THE SPACE TEMPERATURE
(HSP) HEATING SETPOINT THE STEAM CONTROL VALVE WILL MODULATE “OPEN” TO THE COIL. WHEN THE SPACE TEMPERATURE (RMT) IS> THE SPACE HEATING SETPOINT (HSP) THE STEAM CONTROL VALVE WILL
MODULATE “CLOSED” TO THE COIL.
J. DISCHARGE AIR TEMPERATURE LOW-LIMIT:
THE STEAM CONTROL VALVE MODULATE TO MAINTAIN THE DISCHARGE AIR TEMPERATURE (DAT) AT OR ABOVE THE DISCHARGE AIR LOW LIMIT (DALL) OF 60 °F (ADJ.). WHEN THE DISCHARGE AIR TEMPERATURE (DAT)
FAILS TO INCREASE ABOVE 60 °F AFTER THE STEAM CONTROL VALVE IS FULLY OPEN, THE OUTSIDE DAMPER (OAD) WILL BE MODULATED “CLOSED” & AN ALARM WILL BE GENERATED. (DATLO).
K. ALARMS & SAFETIES MONITORING:
1. FAN FAILURE (FANFAIL): COMMANDED ON, BUT THE STATUS (CS) IS “OFF”.
2. FAN IN HAND (FANHAND): COMMANDED OFF, BUT THE STATUS (CS) IS ON.
3. HI/LOW SPACE AIR TEMP: WHEN THE SPACE TEMPERATURE (RMT) IS > 85 °F (ADJ.) < 55 °F (ADJ.).
4. HI/LOW DISCHARGE AIR TEMP: WHEN THE DISCHARGE AIR TEMPERATURE (DAT) IS > 120 °F (ADJ.) < 50 °F (ADJ.).
5. LOW TEMPERATURE LIMIT SWITCH (LLSTRIP): WHEN THE SENSOR TRIPS, UPON THE TEMPERATURE BELOW THE SETTING.
6. HEATING FAILURE: (HEATFAIL) AN ALARM WILL BE GENERATED WHEN THE DISCHARGE AIR TEMPERATURE (DAT) REMAINS WITHIN 4°F (ADJ.) OF THE HEATING SETPOINT (HSP) & THE HEATING SIGNAL
IS > 10% “OPEN” (FOR > 5 MINUTES) THIS ALARM WILL NOT BE ENABLED UNTIL THE ZONE HAS BEEN “ON” FOR 10 MINUTES (ADJ.).

CLIENT
Fairfield, NJ 07004
Building Automation and AHU SEQUENCE OF OPERATION
Temperature Control
(M) 973-214-6886
AHU BILL OF MATERIAL
AHU BILL OF MATERIAL

1 Programmable Controller C1 PUB6438S 1 Honeywell Spyder Controller with 6UI, 4DI, 3AO, 8DO Honeywell
2 Discharge air temperature DAT A/20K-D-12"-GD 1 ACI, 12" 20K Duct Temp Sensor for AHU Supply Air Temp ACI
3 ZONE Temp Sensor ZNT-# A/20K-R2S 1 ACI, 20K Room Temp sensor, set point ACI
4 Thermostat protector - BA/BG2 1 Smaller BAPI-Guard 2 Thermostat protector Bapi
5 Freeze-Stats FRZ A/FLS-20-A 1 Low limit temperature control, DPDT, Auto Reset, 20' ft capillary ACI
7 Field mounted relay FR-# RIBU1C 2 FUNCT. Device Relay in Box, 1-SPDT, 24V/120VAC Functional Devices
9 Panel CP-# SCE-20N2006LP 1 20"H X 20"W X 6" Depth NEMA-1 Enclosure, steel ANSI61-Grey Saginaw
10 Perforated Subpanel CP-# SCE-20N20MP 1 Subpanel, NEMA-1 Saginaw
* REUSE EXISTING SENSORS & END DEVICES WHEREVER POSSIBLE. EXISTING UNIT DUCT SIZES ARE NOT AVAILABLE. FIELD TO COORDINATE THE LENGTH FOR FREEZSTAT, MAT, DAT & RAT PRIOR TO ORDERING NEW.

CLIENT
Fairfield, NJ 07004
Building Automation and AHU BILL OF MATERIAL
Temperature Control
(M) 973-214-6886
AHU PANEL LAYOUT
CP-2
CP-2
1"
24
23
21 AO-1
22 COM
23 AO-2
24 AO-3
25 COM
26 DI-1
27 DI-2
28 COM
29 DI-3
30 DI-4
31 20VDC
32 UI-1
33 COM
34 UI-2
35 UI-3
36 COM
37 UI-4
38 UI-5
39 COM
40 UI-6
22
21
5.5"
Spyder™
PUB6438S
Sylk™
Enhanced
SBUS1
SBUS2
24VAC
24VAC
EGND
SHLD
BAC+
BAC-
DO-1
DO-2 10
DO-3 12
DO-4 13
DO-5 15
DO-6 16
DO-7 18
DO-8 19
COM
COM 11
COM 14
COM 17
COM 20
1
2
3
4
5
6
7
8
9
7"
20" 18" 1" 1"

1"
1"
3"
TR-1
4" 10
9
8
7
6
5 PANEL
GROUND
4
3
2 N 120VAC
1
ø (BY OTHERS)
2"
18"
20"
NOTES :

CLIENT
Fairfield, NJ 07004
Building Automation and AHU PANEL LAYOUT
Temperature Control
(M) 973-214-6886
GYM AHU SCHEMATIC DIAGRAM
(TYPICAL OF-2)
*NOTE-1
SYLK
SYLK
ZN-T/CO2
ZONE TEMPERATURE & CO2
C1 SENSOR
UI-4
RAT
RETURN
AIR
T1 2
T2 1 RAD
AO-2 3 C1
NO FOR INTERLOCK.
C1 C1 DI-2 C1
UI-2 UI-1 UI-3
OAT FILTER MAT STEAM COIL FRZ SUPPLY FAN DAT
OUTSIDE SUPPLY
NC
AIR AIR TO GYM
C
OAD DI-1
X T1 C1
V-# X T2
X
X
AO-1 C1
S/S
X
DO-1
STARTER
COND. LPS PANEL
AHU SCHEDULE
1 AHU FIRST FLOOR 158-STORAGE
2 AHU FIRST FLOOR 156-STORAGE
NOTE:-
1. BOTH AHU SERVING SAME ZONES, SHARES COMMON ZONE TEMP & CO2 SENSOR.

CLIENT
Fairfield, NJ 07004
Building Automation and GYM AHU SCHEMATIC DIAGRAM
Temperature Control
(M) 973-214-6886
GYM AHU WIRING DIAGRAM
120 VAC
BY OTHERS
(TYPICAL OF-2)
24VAC
ø N OUTPUT
1 2 3 4 5 6
TR-1
24 VAC
H N H T1
T2
T1 N COM
T2
C1
40 UI-6 COM 20
39 COM DO-8 19
RAT 30 C3
RAT
RETURN AIR
29 38 UI-5 DO-7 18
TEMPERATURE
RAT
37 UI-4
COM 17
DAT 28 C3
PUB6438S
DAT
DISCHARGE AIR C3 36 COM

TEMPERATURE 27 DO-6 16
DAT
35 UI-3
DO-5 15
26 OAT
OAT
OAT 34 UI-2
OUTSIDE AIR TEMPERATURE COM 14
25 C2
C2 33 COM
DO-4 13
24 MAT
MAT
MAT 32 UI-1 C4 WHT/YEL FR-2 BLU

10 X SF- SFTY
SFTY
MIXED AIR TEMPERATURE DO-3 12 C
FAN PANEL
23 C2 WHT/BLU YEL SF SAFETY
X
9
31 20VDC COM 11 C4
SF SFTY
30 DI-4 DO-2 10 WHT/YEL FR-1 ORG
C4 8 X SF- S/S
S/S
PUB6438S
22 WHT/BLU
C
YEL FAN PANEL
SF S/S
Enhanced
X SF START/STOP
Spyder™
29 DI-3 DO-1 9
FRZ
FRZ STAT 7
21 C1
FREEZESTAT ALARM
Sylk™
C1 28 COM
20 T1
FRZ STAT
19 27 DI-2
FROM
CS-1 26 DI-1 PREVIOUS
18 C1 BACNET
CS-1 BAC- 8 DEVICE
SUPPLY FAN STATUS 17 25 COM
BAC+ 7 TO NEXT *NOTE-2
BACNET
24 AO-3 DEVICE
3 16 SBUS2 6
ECON DMPR CTRL ECON DMPR CTRL
1 23 AO-2
ECON DAMPER CONTROL 15 T2
2 SBUS1 5
14 22 COM
SHLD 4 ZN-T/CO2
STM VLV CTRL
21 AO-1
ZONE TEMPERATURE &
EGND 3 CO2 SENSOR
13
X 24VAC T2
12 T2 COM 2
STM VLV CTRL
X
STEAM VALVE CONTROL
X 11 24VAC 1 T1
LOCATION : FIELD TO VERIFY
NOTES :
1. VERIFY AND REUSE EXISTING FREEZSTAT INTERLOCK WIRING, IF FOUND
IN WORKING CONDITION.
2. ZN-T/CO2 APPLICABLE FOR ONLY ONE AHU, AS BOTH AHU SERVING SAME
ZONES, SHARES COMMON ZONE TEMP & CO2 SENSOR.

CLIENT
Fairfield, NJ 07004
Building Automation and GYM AHU WIRING DIAGRAM
Temperature Control
(M) 973-214-6886
GYM AHU SEQUENCE OF OPERATION PAGE 1
A. SCHEDULING: THE SCHEDULE WILL BE COMMUNICATED TO THE UNIT’S BACNET MS/TP DDC CONTROLLER AS ESTABLISHED IN THE GUI. THE UNIT WILL REMAIN IN THE “UNOCCUPIED” MODE UNTIL THE
SUPPLY FAN CURRENT SWITCH (SFCS) HAS PROVEN THE SUPPLY FAN “ON”.
B. SPACE TEMPERATURE SENSOR (RMT):
THE SPACE TEMPERATURE SENSOR (RMT) WILL HAVE A LOCALLY ADJUSTABLE HEATING SETPOINT WITH AN OVERRIDE PUSHBUTTON; WHEN THE BUTTON IS DEPRESSED, THE LED WILL LIGHT & THE UNIT WILL BE
SCHEDULED INTO THE “OCCUPIED” MODE FOR UP TO 3 HOURS (ADJ.); UPON THE EXPIRATION OF THE OVERRIDE, THE UNIT WILL REVERT TO ITS SCHEDULED MODE. THE SPACE HEATING (HSP/UHSP)WILL BE CONTROLLED
FROM THE GUI. THE SETPOINTS WILL BE INITIALLY SET AT 72 °F (ADJ.) FOR HEATING (HSP) WITH A SETPOINT ADJUSTMENT SPAN SETTING OF ± 4 °F (ADJ.).
C. “UNOCCUPIED” MODE:
WHEN THE UNIT IS SCHEDULED IN THE “UNOCCUPIED” MODE; THE UNIT’S SUPPLY FAN (SFSS), AND ANY ASSOCIATED EXHAUST FANS (EFSS) WILL BE COMMANDED “OFF”; THE OUTSIDE DAMPERS (OAD) WILL BE
“CLOSED” & THE RETURN DAMPER (RAD) WILL BE OPEN; WHEN THE OUTSIDE AIR TEMPERATURE (OAT) IS > 45 °F, THE STEAM CONTROL VALVE BE “CLOSED” TO THE COIL. WHEN THE OUTSIDE AIR TEMPERATURE (OAT) IS
< 48 °F, THE STEAM CONTROL VALVE WILL MODULATE TO MAINTAIN A DISCHARGE AIR SETPOINT (DASP) OF 85 °F.
D. “UNOCCUPIED COOLING” MODE: NONE
E. “UNOCCUPIED HEATING” MODE:
WHEN ANY SPACE TEMPERATURE SENSOR (RMT) IS < THE “UNOCCUPIED HEATING” SETPOINT (UHSP) OF 60 °F (ADJ.), THE UNIT’S SUPPLY FAN (SFSS) WILL BE COMMANDED “ON”. ANY ASSOCIATED EXHAUST FANS (EFSS)
WILL REMAIN “OFF”. WHEN THE SPACE TEMPERATURE (RMT) IS > THE “UNOCCUPIED HEATING” SETPOINT (UHSP) HYSTERESIS, THE UNIT’S SUPPLY FAN (SFSS) WILL BE COMMANDED “OFF”.
F. “OCCUPIED” MODE:
WHEN THE UNIT IS SCHEDULED IN THE “OCCUPIED” MODE THE UNIT SUPPLY FAN (SFSS) AND ANY ASSOCIATED EXHAUST FANS (EFSS) WILL BE COMMANDED “ON” & RUN CONTINUOUSLY. THE OUTSIDE AIR (OAD),
EXHAUST AIR (EAD) & RETURN AIR (RAD) DAMPERS WILL “OPEN” TO THE MINIMUM OUTSIDE AIR SETTING (ADJ.) (OAMINSP). UPON THE TRANSITION OF THE UNIT TO “OCCUPIED” MODE, A 10 MINUTE RAMP WILL BE
IMPLEMENTED BEFORE THE OUTSIDE DAMPERS (OAD) CAN GO FULLY OPEN.
G. “MORNING WARM-UP” MODE:
THE UNIT WILL BE PLACED IN “WARM-UP” MODE WHEN THE SPACE TEMPERATURE (RMT) IS > 5 °F (ADJ.) BELOW THE SPACE HEATING SETPOINT (HSP) OR THE RETURN AIR TEMPERATURE (RAT) IS < THE “WARM-UP”
SETPOINT (WUSP) OF 66 °F (ADJ.) (WUSP). WHEN THE UNIT IS PLACED IN WARM-UP MODE ALL ASSOCIATED EXHAUST FANS (EFSS) WILL BE COMMANDED “OFF”; THE OUTSIDE AIR (OAD) & EXHAUST AIR (EAD) DAMPERS
WILL BE “CLOSED”. THE RETURN DAMPER (RAD) WILL BE OPENED, THE HOT WATER CONTROL VALVE WILL BE MODULATED “OPEN” TO THE COIL TO MAINTAIN A DISCHARGE AIR SETPOINT (DASP) OF 85 °F (ADJ.). THE
UNIT WILL BE RELEASED FROM “WARM-UP” MODE WHEN THE RETURN AIR TEMPERATURE (RAT) > THE “WARM-UP” SETPOINT (WASP) HYSTERESIS OR THE SPACE TEMPERATURE (RMT) IS < 2 °F (ADJ.) BELOW THE SPACE
HEATING SETPOINT (HSP). WHEN THE UNIT IS RELEASED FROM WARM-UP MODE THE OUTSIDE AIR (OAD), EXHAUST AIR (EAD) & RETURN AIR (RAD) DAMPERS, THE STEAM CONTROL VALVE WILL REVERT TO THEIR
SCHEDULED MODE.
H. MINIMUM OUTSIDE AIR CONTROL:
THE TESTING & BALANCING CONTRACTOR (TAB) WILL ADJUST & SET THE OUTSIDE AIR MINIMUM SETTING (OAMINSP). THE OUTSIDE AIR (OAD) & RETURN AIR (RAD) DAMPERS WILL POSITION ACCORDING TO THE
SEQUENCE OF OPERATIONS.
I. “HEATING” MODE:
THE STEAM CONTROL VALVE WILL MODULATE TO MAINTAIN THE SPACE TEMPERATURE (RMT) AT OR ABOVE THE SPACE HEATING SETPOINT (HSP). WHEN THE SPACE TEMPERATURE (RMT) IS < THE SPACE TEMPERATURE
(HSP) HEATING SETPOINT THE STEAM CONTROL VALVE WILL MODULATE “OPEN” TO THE COIL. WHEN THE SPACE TEMPERATURE (RMT) IS> THE SPACE HEATING SETPOINT (HSP) THE STEAM CONTROL VALVE WILL
MODULATE “CLOSED” TO THE COIL.
J. FREE COOLING ECONOMIZER:
WHEN THE OUTSIDE AIR TEMPERATURE (OAT) IS < THE SPACE TEMPERATURE (RMT) BY > 8 °F (ADJ.) THE USE OF THE FREE COOLING ECONOMIZER WILL BE USED TO COOL THE SPACE TEMPERATURE (RMT) AS REQUIRED.
THE OUTSIDE AIR (OAD) & RETURN AIR (RAD) DAMPERS WILL MODULATE TO MAINTAIN MIXED AIR TEMPERATURE SETPOINT (MASP) - 10°F TO THE SPACE COOLING SETPOINT (CSP). WHEN THE SPACE TEMPERATURE (RMT)
IS > THE SPACE COOLING SETPOINT (CSP) THE OUTSIDE AIR (OAD) WILL BE MODULATED OPEN; THE RETURN AIR (RAD) DAMPERS MODULATED CLOSED. WHEN THE SPACE TEMPERATURE (RMT) IS < THE SPACE COOLING
SETPOINT (CSP) THE OUTSIDE AIR (OAD) DAMPERS WILL BE MODULATED CLOSED; THE RETURN AIR (RAD) DAMPER MODULATED OPEN.
L. DISCHARGE AIR TEMPERATURE LOW-LIMIT:
THE HOT WATER CONTROL VALVE MODULATE TO MAINTAIN THE DISCHARGE AIR TEMPERATURE (DAT) AT OR ABOVE THE DISCHARGE AIR LOW LIMIT (DALL) OF 60 °F (ADJ.). WHEN THE DISCHARGE AIR TEMPERATURE
(DAT) FAILS TO INCREASE ABOVE 60 °F AFTER THE STEAM CONTROL VALVE IS FULLY OPEN, THE OUTSIDE DAMPER (OAD) WILL BE MODULATED “CLOSED” & AN ALARM WILL BE GENERATED. (DATLO).

CLIENT
Fairfield, NJ 07004 GYM AHU SEQUENCE OF OPERATION
Building Automation and PAGE 1
Temperature Control
(M) 973-214-6886
GYM AHU SEQUENCE OF OPERATION PAGE 2
M. DCV:
THE BMS SHALL MONITOR CO2 LEVELS. THE BMS SHALL MODULATE THE OUTSIDE AIR DAMPER FROM ITS MINIMUM OUTSIDE AIR POSITION TO THE MAXIMUM OUTSIDE AIR POSITION TO MAINTAIN CO2
CONCENTRATION SET-POINT. CONTROLLER SHALL NOT ALLOW MIXED AIR TEMPERATURE TO DROP BELOW 50°F OR GOES ABOVE 85°F DURING HIGH CO2 CONDITION.
N. ALARMS & SAFETIES MONITORING:

1. FAN FAILURE (FANFAIL): COMMANDED ON, BUT THE STATUS (CS) IS “OFF”.
2. FAN IN HAND (FANHAND): COMMANDED OFF, BUT THE STATUS (CS) IS ON.
3. HI/LOW SPACE AIR TEMP: WHEN THE SPACE TEMPERATURE (RMT) IS > 85 °F (ADJ.) < 55 °F (ADJ.).
4. HI/LOW DISCHARGE AIR TEMP: WHEN THE DISCHARGE AIR TEMPERATURE (DAT) IS > 120 °F (ADJ.) < 50 °F (ADJ.).
5. LOW TEMPERATURE LIMIT SWITCH (LLSTRIP): WHEN THE SENSOR TRIPS, UPON THE TEMPERATURE BELOW THE SETTING.
6. HEATING FAILURE: (HEATFAIL) AN ALARM WILL BE GENERATED WHEN THE DISCHARGE AIR TEMPERATURE (DAT) REMAINS WITHIN 4°F (ADJ.) OF THE HEATING SETPOINT (HSP) & THE HEATING SIGNAL
IS > 10% “OPEN” (FOR > 5 MINUTES) THIS ALARM WILL NOT BE ENABLED UNTIL THE ZONE HAS BEEN “ON” FOR 10 MINUTES (ADJ.).

CLIENT
Fairfield, NJ 07004 GYM AHU SEQUENCE OF OPERATION
Building Automation and PAGE 2
Temperature Control
(M) 973-214-6886
GYM AHU BILL OF MATERIAL
GYM AHU BILL OF MATERIAL

2 Duct Temp Sensor DAT A/20K-D-12"-GD 6 ACI, 12" 20K Duct Temp Sensor for AHU Supply Air Temp ACI
3 Averaging duct Temperature MAT A/20K-FA-24'-PB 2 Thermistor, Flexible Cable Averaging, 20K ohm NTC, 24', Plastic Box ACI
4 ZONE Temp Sensor ZNT/CO2 TR42-CO2 1 TR42 LCD Wall module, Temperature WITH CO2, two-wire Sylk Honeywell

CLIENT
Fairfield, NJ 07004
Building Automation and GYM AHU BILL OF MATERIAL
Temperature Control
(M) 973-214-6886
UV SCHEMATIC DIAGRAM
(TYPICAL OF 7)
ZONE TEMP SENSOR
UI-3 SEN+
C1 SEN-
RETURN UI-2 SET
AIR C1 SET
ZN-T
C1
FOR INTERLOCK. UI-1
DI-1
C1
FILTER HOT WATER COIL DX COIL SUPPLY FAN DAT
FRZ
H
OUTSIDE SUPPLY
AIR OA/RA AIR
DAMPER
C
C1 C1
X T2
3 2 1 DO-2 DI-2
V-# X T1
X *120VAC
AO-2
AO-1 WHT/YEL FR-# ORG
T1
T2
C1 N
C
BY OTHERS
WHT/BLU YEL
DO-1 L
HWS HWR
FTR-1
DO-3
C1
HWS HWR
V-#
UV SCHEDULE
ITEM# TAG FLOOR LOCATION NEARBY FTR
1 UV-1 GROUND FLOOR G6-MUSIC
2 UV-2 GROUND FLOOR G2-MULTIPURPOSE ROOM 3
3 UV-3 GROUND FLOOR G2-MULTIPURPOSE ROOM 2 FTR-1
4 UV-4 GROUND FLOOR G2-CLASSROOM
NOTE:-
1. FOR UV-3 & FTR- 1 SERVING SAME ZONES, SHARES COMMON ZONE TEMP SENSOR.
2. FTR-1 VLV APPLICABLE FOR ONLY UV-3.

CLIENT
Fairfield, NJ 07004
Building Automation and UV SCHEMATIC DIAGRAM
Temperature Control
(M) 973-214-6886
UV WIRING DIAGRAM
(TYPICAL OF 7)
TR-1
24 VAC
H T1
N COM
T2
C1
T2
40 UI-6 COM 20
39 COM DO-8 19
38 UI-5 DO-7 18
37 UI-4
COM 17 *NOTE-5
PUB6438S
C3 36 COM WHT/YEL FR-3 BLK FTR-1 VLV CMD
DO-6 16 C5
ZNT-1 WHT/BLU
C
BLK FTR-1 VALVE
SEN- C3 35 UI-3 COMMAND
ZNT-1 DO-5 15
SEN+ T1
ZONE TEMPERATURE SENSOR ZNT-1 SP 34 UI-2
WITH SETPOINT SET COM 14 C5
T2
SET C2
C2 33 COM
DO-4 13
DAT
32 UI-1 FTR-1 CMD WHT/YEL ORG
DAT
DAT DO-3 12 C4 FR-2

X DX STG CMD
STG
C
DISCHARGE AIR TEMPERATURE WHT/BLU YEL DX STG
C2 X DX STAGE COMMAND
31 20VDC COM 11 C4
DX STG CMD SF S/S

30 DI-4 DO-2 10 WHT/YEL
FR-1
ORG SUPPLY FAN
C4
START/STOP
PUB6438S
C
WHT/BLU YEL
SF S/S
Enhanced
Spyder™
SF STS 29 DI-3 DO-1 9
C1
SA FAN STATUS
Sylk™
C1 28 COM L N
SF STS
FRZ
FRZ STAT C1 27 DI-2 *120VAC

FREEZE STAT STATUS FROM BY OTHERS
T1 FRZ STAT PREVIOUS
26 DI-1
BACNET
BAC- 8 DEVICE
25 COM TO NEXT
BAC+ 7
2 BACNET
ECON DMPR CTRL 24 AO-3 DEVICE
ECON DAMPER CONTROL 1
ECON DMPR CTRL SBUS2 6
3 23 AO-2
SBUS1 5
X 22 COM
HTG VLV CTRL
HEATING VALVE CONTROL X SHLD 4
HTG VLV CTRL
X 21 AO-1
EGND 3
24VAC T2
COM 2
24VAC 1 T1
LOCATION : RESPECTIVE UV CABINET
NOTE:-
1. CONTROLLERS TO BE DIRECTLY INSTALLED IN UV CABINET.
2. REFER TO UV SCHEDULE FOR DETAILS OF RESPECTIVE DETAILS.
3. VERIFY AND REUSE EXISTING FREEZSTAT INTERLOCK WIRING, IF FOUND IN WORKING CONDITION.
4. FOR UV-3 & FTR- 1 SERVING SAME ZONES, SHARES COMMON ZONE TEMP SENSOR.
5. FTR-1 VLV CMD APPLICABLE FOR ONLY UV-3.

CLIENT
Fairfield, NJ 07004
Building Automation and UV WIRING DIAGRAM
Temperature Control
(M) 973-214-6886
UV SEQUENCE OF OPERATION PAGE 1
(TYPICAL OF 7)
A. RUN CONDITIONS - SCHEDULED:
1. THE UNIT SHALL RUN ACCORDING TO A USER DEFINABLE TIME SCHEDULE IN THE FOLLOWING MODES:
A)OCCUPIED MODE: THE UNIT SHALL MAINTAIN
A 75°F (ADJ.) COOLING SETPOINT
A 70°F (ADJ.) HEATING SETPOINT.
B) UNOCCUPIED MODE (NIGHT SETBACK): THE UNIT SHALL MAINTAIN
• A 85°F (ADJ.) COOLING SETPOINT.
• A 55°F (ADJ.) HEATING SETPOINT.
C) ALARMS SHALL BE PROVIDED AS FOLLOWS:
• HIGH ZONE TEMP: IF THE ZONE TEMPERATURE IS GREATER THAN THE COOLING SETPOINT BY A USER DEFINABLE AMOUNT (ADJ.).
• LOW ZONE TEMP: IF THE ZONE TEMPERATURE IS LESS THAN THE HEATING SETPOINT BY A USER DEFINABLE AMOUNT (ADJ.).
B. ZONE SETPOINT ADJUST:

THE OCCUPANT SHALL BE ABLE TO ADJUST THE ZONE TEMPERATURE HEATING SETPOINT AT THE ZONE SENSOR. THIS FUNCTION CAN BE DISABLED AT FRONT END (IF PRESENT).
C. FREEZE PROTECTION:
THE UNIT SHALL SHUT DOWN, HOT WATER WATER VALVE WILL OPEN 100% AND GENERATE AN ALARM UPON RECEIVING A FREEZESTAT STATUS. OUTSIDE AIR DAMPER WILL CLOSE AND RETURN AIR DAMPER WILL OPEN.
D. ZONE OPTIMAL START:

THE UNIT SHALL USE AN OPTIMAL START ALGORITHM FOR MORNING START-UP. THIS ALGORITHM SHALL MINIMIZE THE UNOCCUPIED WARM-UP OR COOL-DOWN PERIOD WHILE STILL ACHIEVING COMFORT CONDITIONS
BY THE START OF SCHEDULED OCCUPIED PERIOD.
E. SUPPLY FAN:
1. THE SUPPLY FAN SHALL RUN ANYTIME THE UNIT IS COMMANDED TO RUN, UNLESS SHUTDOWN ON SAFETIES. TO PREVENT SHORT CYCLING, THE SUPPLY FAN SHALL HAVE A USER DEFINABLE (ADJ.) MINIMUM RUNTIME.
2. ALARMS SHALL BE PROVIDED AS FOLLOWS:
• SUPPLY FAN FAILURE: COMMANDED ON, BUT THE STATUS IS OFF.
• SUPPLY FAN IN HAND: COMMANDED OFF, BUT THE STATUS IS ON.
• SUPPLY FAN RUNTIME EXCEEDED: STATUS RUNTIME EXCEEDS A USER DEFINABLE LIMIT (ADJ.).
F. HOT WATER COIL VALVE:

1. THE CONTROLLER SHALL MEASURE THE ZONE TEMPERATURE AND MODULATE THE HEATING VALVE TO MAINTAIN ITS HEATING SETPOINT.
2. THE HEATING SHALL BE ENABLED WHENEVER:
• OUTSIDE AIR TEMPERATURE IS LESS THAN 65°F (ADJ.).
• AND THE ZONE TEMPERATURE IS BELOW HEATING SETPOINT.
• AND THE SUPPLY FAN STATUS IS ON.
• AND THE COOLING IS NOT ACTIVE.
G. FINNED TUBE RADIATION (WHEREVER PRESENT):

1ST STAGE HEAT SHALL BE HOT WATER BASEBOARD HEAT AND 2ND STAGE HEAT SHALL BE REHEAT COIL. FTR VALVE WILL OPEN AT 70 DEG. F (ADJUSTABLE). IF THE ROOM TEMPERATURE REACHES 71.5 THE FTR VALVE
WILL CLOSE. IF THE FTR VALVE IS OPEN AND THE SPACE TEMPERATURE DROPS TO 69 DEG. F, THE REHEAT CONTROL VALVE IN THE UNIT WILL MODULATE OPEN. IF THE SPACE TEMPERATURE RISES TO 70.5 DEG. F, THE
REHEAT CONTROL VALVE WILL MODULATE CLOSE.

CLIENT
Fairfield, NJ 07004
Building Automation and UV SEQUENCE OF OPERATION PAGE 1
Temperature Control
(M) 973-214-6886
UV SEQUENCE OF OPERATION PAGE 2
(TYPICAL OF 7)
H. ECONOMIZER:
ON CALL FOR COOLING THE ECONOMIZER SHALL BE ENABLED. THE CONTROLLER SHALL MEASURE THE ZONE TEMPERATURE AND MODULATE THE ECONOMIZER DAMPERS IN SEQUENCE TO MAINTAIN DISCHARGE AIR
SETPOINT OF 58°F (ADJ.). DURING ECONOMIZER MODE, CONTROLLER WILL MEASURE THE DISCHARGE AIR TEMPERATURE AND MODULATE THE DAMPER TO MAINTAIN DISCHARGE AIR LOW LIMIT SETPOINT OF 58 DEG. F
(ADJ.). THE OUTSIDE AIR DAMPERS SHALL MAINTAIN A MINIMUM ADJUSTABLE POSITION OF 20% (ADJ.) OPEN DURING HEATING AND VENTILATION WHENEVER OCCUPIED.
THE ECONOMIZER SHALL BE ENABLED WHENEVER:
• OUTSIDE AIR TEMPERATURE IS AT LEAST 3°F (ADJ.) LESS THAN THE ZONE TEMPERATURE.
• AND THE OUTSIDE AIR TEMPERATURE IS LESS THAN 75 °F (ADJ.)
• AND THE SUPPLY FAN STATUS IS ON.
THE ECONOMIZER SHALL CLOSE WHENEVER:

• ON LOSS OF SUPPLY FAN STATUS
• OR FREEZESTAT IS ON
I. SUPPLY AIR TEMPERATURE:

1. THE CONTROLLER SHALL MONITOR THE SUPPLY AIR TEMPERATURE.
2. ALARMS SHALL BE PROVIDED AS FOLLOWS:
• HIGH SUPPLY AIR TEMP: IF THE SUPPLY AIR TEMPERATURE IS GREATER THAN 120°F (ADJ.).
• LOW SUPPLY AIR TEMP: IF THE SUPPLY AIR TEMPERATURE IS LESS THAN 45°F (ADJ.).

CLIENT
Fairfield, NJ 07004
Building Automation and UV SEQUENCE OF OPERATION PAGE 2
Temperature Control
(M) 973-214-6886
UV BILL OF MATERIAL
UV BILL OF MATERIAL
2 Discharge air temperature DAT TE-DFN-F0848-00 7 Air Duct Temperature Sensor, 8 inch probe, 20K Ohm Thermistor. Dwyer
3 ZONE Temp Sensor ZNT A/20K-R2S 7 ACI, 20K Room Temp sensor, set point ACI
6 Current Switch CS-1 C-2300 7 Split core, Adj. trip, Min trip at 0.5 A, status output N.O. 1.0 A @ 30VAC/DC Senva
8 Transformers TR-1 10051MWCB 7 96 VA 120-208-240, 277-480V Pri. -24V Sec Multi-tap Class 2 Transformer Senva

CLIENT
Fairfield, NJ 07004
Building Automation and UV BILL OF MATERIAL
Temperature Control
(M) 973-214-6886
STEAM RADIATOR SCHEMATIC DIAGRAM
(TYPICAL OF 8)
C1 SEN-
UI-# SEN+
C1 SET
UI-# SET
FTR-# ZN-T
FTR-#
DO-#
C1
LPS COND
V-#
RADIATOR SCHEDULE
ITEM# TAG FLOOR LOCATION NEARBY UV/RAD TYPE
1 FTR-1 GROUND FLOOR G5 MULTIPURPOSE ROOM UV-3
2 FTR-2 FIRST FLOOR 107 TEACHERS LOUNGE
3 FTR-3 FIRST FLOOR 106 MAIN OFFICE
4 FTR-4 FIRST FLOOR 103 PRINCIPAL TYPE-1
5 FTR-5 FIRST FLOOR 111 CLASSROOM
6 FTR-6 FIRST FLOOR 115 NURSE
7 FTR-7 SECOND FLOOR 205 GUIDANCE
TYPE-2
8 FTR-8 SECOND FLOOR 215 RESOURCE
NOTE:-
1. FOR FTR-1 REFER UV-3 WIRING DETAILS.

CLIENT
Fairfield, NJ 07004
Building Automation and STEAM RADIATOR SCHEMATIC DIAGRAM
Temperature Control
(M) 973-214-6886
STEAM RADIATOR W/INLINE FAN SCHEMATIC DIAGRAM
(TYPICAL OF 10)
C1 SEN-
UI-# SEN+
C1 SET
UI-# SET
RWF-# ZN-T
BLK
BLK
LPS
NO
COND
ORG
FR-#
DO-# WHT/YEL YEL
WHT/BLU
C PRP
C-X
BRN
L N
*120V BY OTHERS
RWF-#
RADIATOR W/ INLINE FAN SCHEDULE

ITEM# TAG FLOOR LOCATION RAD TYPE
1 RWF-1 FIRST FLOOR 110 CLASSROOM TYPE-1
2 RWF-2 FIRST FLOOR 118 CLASSROOM
3 RWF-3 FIRST FLOOR 120A CLASSROOM TYPE-3
4 RWF-4 FIRST FLOOR 120B CLASSROOM
5 RWF-5 SECOND FLOOR 206 CLASSROOM
TYPE-2

CLIENT
Fairfield, NJ 07004 STEAM RADIATOR W/INLINE FAN
Building Automation and SCHEMATIC DIAGRAM
Temperature Control
(M) 973-214-6886
RADIATOR TYPE-1 WIRING DIAGRAM PAGE 1
120 VAC
CP-3 ø N OUTPUT OUTPUT
1 2 3 4 5 6 7 8 9
TR-1 TR-2
T1 T3 24 VAC 24 VAC
H N H T1 H T3
T2 T4
N COM N COM
T2 T4
T4
T3
C1 BLK
BLK RWF-1 CMD
ORG
WHT/YEL FR-6 RAD WITH FAN-1
21 YEL
WHT/BLU
C COMMAND
SEN- 33 PRP
FTR-4 ZNT FTR-4 ZNT 20
40
20
FTR-4 ZONE SEN+ UI-6 DO-B4 BRN
32 C3
TEMPERATURE SENSOR SET
39
19
31 C3 COM DO-B3 L N
SET
FTR-4 ZNT SP RWF-1 CMD *120VAC
30 C3
38
18
UI-5 DO-B2 BY OTHERS
FTR-3 ZNT FTR-6 CMD
37
17
UI-4 DO-B1
FTR-3 ZNT
SEN- 29 PUB6438SR FTR-5 CMD
36
C2
16
FTR-3 ZONE SEN+ COM DO-A3 19 WHT/YEL BLK FTR-6 VLV CMD
28 C2 FR-5 ORG
TEMPERATURE SENSOR SET C FTR-6 VALVE
FTR-3 ZNT SP FTR-4 CMD 18 WHT/BLU YEL BLK
35
15
SET 27 UI-3 DO-A2 COMMAND
26 C2 FTR-2 ZNT FTR-3 CMD
34
14
UI-2 DO-A1 17 WHT/YEL FR-4 ORG BLK
C
FTR-5 VLV CMD
FTR-2 CMD WHT/BLU YEL BLK FTR-5 VALVE
33
16
13
C1 COM DO-C1
SEN- 25 COMMAND
FTR-2 ZNT FTR-2 ZNT SP
32
12
FTR-2 ZONE SEN+ UI-1 COM-C 15
24 C1 WHT/YEL FR-3 ORG BLK FTR-4 VLV CMD
TEMPERATURE SENSOR SET C FTR-4 VALVE
WHT/BLU YEL BLK
14
31
11
SET 23 20VDC COM-B COMMAND
C1
30
22
10
Sylk™ Enhanced
DI-4 COM-A
13 WHT/YEL FR-2 ORG BLK
C
FTR-3 VLV CMD
WHT/BLU YEL BLK
29
PUB6438SR
DI-3 24 VAC OUT T3 12 FTR-3 VALVE
9
COMMAND
Spyder™
28
COM
11 WHT/YEL FR-1 ORG BLK
C
FTR-2 VLV CMD
27
DI-2 FROM PREVIOUS 10 WHT/BLU YEL BLK
FTR-2 VALVE
BAC-
8
26 BACNET DEVICE COMMAND
DI-1
BAC+ TO NEXT
7
BACNET DEVICE
25
COM
SBUS2
6
24
AO-3 TO SIO MODULES

SBUS1
5
23
AO-2
SHLD
4
22
COM
EGND
3
21
AO-1
24VAC COM T2
2
24VAC T1
1
LOCATION : 1ST FLOOR CORRIDOR CEILING

CLIENT
Fairfield, NJ 07004 RADIATOR TYPE-1 WIRING DIAGRAM PAGE
Building Automation and 1
Temperature Control
(M) 973-214-6886
CP-3
SIO-1
SIO12000
FTR-6 ZNT
UI-4 12
C5 41 SEN-
FTR-6 ZNT
COM 11 C5 SEN+ FTR-6 ZONE
40
SET TEMPERATURE SENSOR
SEN- 45 FTR-6 ZNT SP
RWF-1 ZNT RWF-1 ZNT UI-3 10 C5 39 SET
SEN+ 24 UI-5
RWF-1 ZONE 44 C6
FTR-5 ZNT 38
TEMPERATURE SENSOR SET UI-2 9
23 COM
SIO12000
43 C6
SET
C4
Sylk I/O
RWF-1 ZNT SP COM 8
42 C6 22 UI-6 C4 37 SEN-
FTR-5 ZNT SP FTR-5 ZNT
UI-1 7 SEN+ FTR-5 ZONE
21 UI-7 36
SET TEMPERATURE SENSOR
7
C4 35 SET
ON
6
ADDRESSING
20 COM 5
SYLK IO
4
3
34
19 UI-8 2
1
18 UI-9 SBUS2 6
17 COM SBUS1 5 FROM C1
16 UI-10
15 UI-11 EGND 3
24VAC T2
14 COM COM 2
13 UI-12 24VAC 1 T1

CLIENT
Temperature Control
(M) 973-214-6886
120 VAC
CP-5 ø N OUTPUT OUTPUT
1 2 3 4 5 6 7 8 9
TR-1 TR-2
T4
T1 T3 24 VAC 24 VAC
H N H T1 H T3 T3
T2 T4
N COM N COM
T2 T4
BLK
ORG BLK RWF-10 CMD
WHT/YEL FR-8
25 C YEL RAD WITH FAN-10
WHT/BLU COMMAND
PRP
24
BRN
L N
C1 *120VAC BY OTHERS
BLK
ORG BLK RWF-9 CMD
WHT/YEL FR-7
23 C YEL RAD WITH FAN-9
SEN- 37 WHT/BLU COMMAND
RWF-5 ZNT RWF-5 ZNT PRP
RWF-10 CMD 22
40
20
RWF-5 ZONE SEN+ UI-6 DO-B4
36 C3 BRN
RWF-9 CMD
39
19
35 C3 COM DO-B3 L N
SET
*120VAC BY OTHERS
RWF-5 ZNT SP RWF-8 CMD
34 C3
38
18
UI-5 DO-B2 BLK
RWF-7 CMD ORG BLK RWF-8 CMD

FTR-8 ZNT WHT/YEL FR-6
37
17
UI-4 DO-B1 21 YEL RAD WITH FAN-8
FTR-8 ZNT
SEN- 33 PUB6438SR RWF-6 CMD 20
WHT/BLU
C
PRP COMMAND
36
C2
16
FTR-8 ZONE SEN+ COM DO-A3 BRN
32 C2
FTR-8 ZNT SP RWF-5 CMD
35
15
UI-3 DO-A2 L N
SET 31
*120VAC BY OTHERS
30 C2 FTR-7 ZNT FTR-8 CMD
34
14
UI-2 DO-A1 BLK
ORG BLK RWF-7 CMD
FTR-7 CMD WHT/YEL FR-5
19
33
13
C1 COM DO-C1 C YEL RAD WITH FAN-7
WHT/BLU
SEN- 29 PRP COMMAND
FTR-7 ZNT FTR-7 ZNT SP 18
32
12
FTR-7 ZONE SEN+ UI-1 COM-C BRN
28 C1
TEMPERATURE SENSOR SET L N
31
11
SET 27 20VDC COM-B
*120VAC BY OTHERS
C1 BLK
30
26
10
Sylk™ Enhanced
DI-4 COM-A
ORG BLK RWF-6 CMD
WHT/YEL FR-4
17 RAD WITH FAN-6
29
PUB6438SR
DI-3 24 VAC OUT T3 YEL
9
C
WHT/BLU COMMAND
PRP
Spyder™
28 16
COM BRN
L N
27
DI-2 FROM PREVIOUS *120VAC BY OTHERS

BAC-
8
BACNET DEVICE
BLK
26
DI-1 RWF-5 CMD

BAC+ TO NEXT ORG BLK
7
WHT/YEL FR-3 RAD WITH FAN-5
BACNET DEVICE 15
25
COM C YEL COMMAND

WHT/BLU
SBUS2 PRP
6
14
24
AO-3 TO SIO MODULES BRN

SBUS1
5
L N
23
AO-2 *120VAC BY OTHERS

SHLD
4
22
COM
EGND
3
13 WHT/YEL FR-2 ORG BLK FTR-8 VLV CMD
FTR-8 VALVE
21
C
AO-1 WHT/BLU YEL BLK
24VAC COM T2 12 COMMAND
2
24VAC T1
1
11 WHT/YEL FR-1 ORG BLK FTR-7 VLV CMD
WHT/BLU
C
YEL BLK FTR-7 VALVE
10 COMMAND
LOCATION : 201 CORRIDOR CEILING

CLIENT
Temperature Control
(M) 973-214-6886
CP-5
SIO-1
SIO12000
RWF-7 ZNT
UI-4 12
C5 45 SEN-
RWF-7 ZNT
COM 11 C5 SEN+ RWF-7 ZONE
44
SEN- 57 SET TEMPERATURE SENSOR
RWF-8 ZNT RWF-7 ZNT SP
SEN+ RWF-8 ZNT UI-3 10 C5 43 SET
RWF-8 ZONE 56 C6 24 UI-5
TEMPERATURE SENSOR SET RWF-6 ZNT
UI-2 9 42
SET 55 23 COM
SIO12000
C6
C4
Sylk I/O
54 C6 RWF-8 ZNT SP COM 8
22 UI-6 C4 41 SEN-
RWF-6 ZNT SP RWF-6 ZNT
RWF-9 ZNT UI-1 7 SEN+ RWF-6 ZONE
21 UI-7 40
53 SET TEMPERATURE SENSOR
SEN-
RWF-9 ZNT 7
C4 39 SET
ON
SEN+ 6
ADDRESSING
RWF-9 ZONE C7 C7 20 COM
52 5
SYLK IO
TEMPERATURE SENSOR SET 4
38
RWF-9 ZNT SP 3
SET 51 19 UI-8 2
1
50 C7 RWF-10 ZNT
18 UI-9 SBUS2 6
C8 17 COM SBUS1 5 FROM C1

SEN- 49
RWF-10 ZNT RWF-10 ZNT SP
RWF-10 ZONE SEN+ 16 UI-10
48 C8
SET 47 15 UI-11 EGND 3
46 C8 24VAC T2
14 COM COM 2
13 UI-12 24VAC 1 T1
LOCATION : 201 CORRIDOR CEILING

CLIENT
Temperature Control
(M) 973-214-6886
RADIATOR TYPE-3 WIRING DIAGRAM
120 VAC
BY OTHERS 24VAC
OUTPUT
CP-4 ø N
1 2 3 4 5 6 TR-1
24 VAC
H T1
H N
T2 N COM
T2
T1
T2
C1 T1
RWF-4 ZNT
40 UI-6 COM 20 BLK
SEN- 24 ORG BLK RWF-4 CMD
RWF-4 ZNT C3 39 COM DO-8 19 WHT/YEL FR-3
C5 12 RAD WITH FAN-4
RWF-4 ZONE SEN+ WHT/BLU
C YEL
23 C3
RWF-4 ZNT SP COMMAND
TEMPERATURE SENSOR SET PRP
38 UI-5 DO-7 18 11
22 BRN
SET
RWF-3 ZNT
37 UI-4 L N
21 C3 COM 17
C2
PUB6438S *120VAC BY OTHERS
36 COM
DO-6 16 BLK
RWF-3 ZNT SP BLK RWF-3 CMD
35 UI-3 ORG
WHT/YEL FR-2
DO-5 15 C4 10 RAD WITH FAN-3
C YEL
RWF-2 ZNT WHT/BLU COMMAND
SEN- 20 34 UI-2 PRP
COM 14 C5 9
RWF-3 ZNT SEN+ BRN
RWF-3 ZONE 19 C2 C1 33 COM
SET DO-4 13 L N
TEMPERATURE SENSOR
SET 18 RWF-2 ZNT SP *120VAC BY OTHERS
32 UI-1 RWF-4 CMD
DO-3 12 BLK
17 C2
ORG BLK RWF-2 CMD
31 20VDC COM 11 C4 WHT/YEL FR-1
C4 8 C YEL RAD WITH FAN-2
WHT/BLU COMMAND
RWF-3 CMD PRP
SEN- 16 30 DI-4 DO-2 10 7
RWF-2 ZNT BRN
PUB6438S
SEN+ RWF-2 CMD
Enhanced
RWF-2 ZONE C1
Spyder™
15 29 DI-3 DO-1 9
SET L N
TEMPERATURE SENSOR
SET 14 *120VAC BY OTHERS
Sylk™
28 COM
13 C1
27 DI-2
FROM
26 DI-1 PREVIOUS
BACNET
BAC- 8 DEVICE
25 COM TO NEXT
BAC+ 7
BACNET
24 AO-3 DEVICE
SBUS2 6
23 AO-2
SBUS1 5
22 COM
SHLD 4
21 AO-1
EGND 3
24VAC T2
COM 2
24VAC 1 T1

CLIENT
Fairfield, NJ 07004
Building Automation and RADIATOR TYPE-3 WIRING DIAGRAM
Temperature Control
(M) 973-214-6886
RADIATOR BILL OF MATERIAL
RADIATOR TYPE-1 BILL OF MATERIAL

1 Programmable Controller C1 PUB6438SR 1 Honeywell Spyder Controller with 6UI, 4DI, 3AO, 8DO Honeywell
2 I/O Module SIO-1 SIO12000 1 Sylk I/O Module, 12 UI, 0 DI, 0 AO, 0 DO Honeywell
5 Field Relay FR-6 RIB2401D 1 Enclosed Pilot Relay 10 Amp DPDT with 24 Vac/dc/120 Vac Coil Functional Devices

5 Field Relay FR-# RIB2401D 6 Enclosed Pilot Relay 10 Amp DPDT with 24 Vac/dc/120 Vac Coil Functional Devices
6 Field mounted relay FR-1&2 RIBU1C 2 FUNCT. Device Relay in Box, 1-SPDT, 24V/120VAC Functional Devices

* REUSE EXISTING SENSORS & END DEVICES WHEREVER POSSIBLE.

CLIENT
Fairfield, NJ 07004
Building Automation and RADIATOR BILL OF MATERIAL
Temperature Control
(M) 973-214-6886
RADIATOR TYPE-1 & 2 PANEL LAYOUT
(TYPICAL OF 2)
CP-3&5
CP-3&5 1"
21 AO-1
22 COM
23 AO-2
24 AO-3
25 COM
26 DI-1
27 DI-2
28 COM
29 DI-3
30 DI-4
31 20VDC
32 UI-1
33 COM
34 UI-2
35 UI-3
36 COM
37 UI-4
38 UI-5
39 COM
40 UI-6
57
56
55
54
5.45"
53
Spyder™
PUB6438SR
Sylk™ C1
Enhanced
24VAC COM
24VAC OUT
COM A 10
COM B 11
COM C 12
24VAC
DO-A1 14
DO-A2 15
DO-A3 16
DO-B1 17
DO-B2 18
DO-B3 19
DO-B4 20
DO-C1 13
SBUS1
SBUS2
EGND
BAC+
SHLD
BAC-
1
2
3
4
5
6
7
8
9
6.85"
1"
13
14
17
16
15
18
19
20
23
22
21
24
UI-10
UI-11
UI-12
COM
COM
COM
COM
UI-5
UI-6
UI-7
UI-8
UI-9
24" 22" 1" SIO1 1.5"
1"
6.27"
SIO12000
Sylk I/O
SIO-12000
24VAC
SBUS1
SBUS2
EGND
COM
COM
COM
UI-1
UI-2
UI-3
UI-4
12
11
10
5
6
1
9
7
4.75"
1"
13
12
3" 3" 11
10
9
8
7
6
5
4
TR-1 TR-2
4"
4"
3
2 120VAC
1 N
ø (BY
OTHERS)
2"
24" 22"
NOTES :

CLIENT
Fairfield, NJ 07004
Building Automation and RADIATOR TYPE-1 & 2 PANEL LAYOUT
Temperature Control
(M) 973-214-6886
RADIATOR TYPE-3 PANEL LAYOUT
CP-4
CP-4
1"
24
23
21 AO-1
22 COM
23 AO-2
24 AO-3
25 COM
26 DI-1
27 DI-2
28 COM
29 DI-3
30 DI-4
31 20VDC
32 UI-1
33 COM
34 UI-2
35 UI-3
36 COM
37 UI-4
38 UI-5
39 COM
40 UI-6
22
21
5.5"
Spyder™
PUB6438S
Sylk™
Enhanced
SBUS1
SBUS2
24VAC
24VAC
EGND
SHLD
BAC+
BAC-
DO-1
DO-2 10
DO-3 12
DO-4 13
DO-5 15
DO-6 16
DO-7 18
DO-8 19
COM
COM 11
COM 14
COM 17
COM 20
1
2
3
4
5
6
7
8
9
7"
20" 18" 1" 1"

1"
1"
3"
TR-1
4" 10
9
8
7
6
5 PANEL
GROUND
4
3
2 N 120VAC
1
ø (BY OTHERS)
2"
18"
20"
NOTES :

CLIENT
Fairfield, NJ 07004
Building Automation and RADIATOR TYPE-3 PANEL LAYOUT
Temperature Control
(M) 973-214-6886
TRV SCHEMATIC DIAGRAM
(TYPICAL OF 17)
CONVECTOR-#
LPS COND.
TRV
TRV SCHEDULE
1 TRV-1 FIRST FLOOR FIRST FLOOR ROOM
2 TRV-2 FIRST FLOOR 102 HALLWAY
3 TRV-3 FIRST FLOOR 102 HALLWAY
4 TRV-4 FIRST FLOOR SW3 STAIRWELL (FIRST FLOOR)
5 TRV-5 FIRST FLOOR SW2 STAIRWELL (FIRST FLOOR)
6 TRV-6 FIRST FLOOR MAIN ENTRANCE 1
7 TRV-7 FIRST FLOOR MAIN ENTRANCE 2
8 TRV-8 FIRST FLOOR FIRST FLOOR ROOM
9 TRV-9 FIRST FLOOR SW4 STAIRWELL
10 TRV-10 FIRST FLOOR SW1 STAIRWELL
11 TRV-11 FIRST FLOOR 117 OFFICE
12 TRV-12 FIRST FLOOR 118 CLASSROOM BATHROOM
13 TRV-13 FIRST FLOOR 150 MULTIPURPOSE ROOM
14 TRV-14 FIRST FLOOR 150 MULTIPURPOSE ROOM
15 TRV-15 SECOND FLOOR 213 CLASSROOM
16 TRV-16 SECOND FLOOR 206 CLASSROOM
17 TRV-17 SECOND FLOOR GT212 WOMENS RESTROOM

CLIENT
Fairfield, NJ 07004
Building Automation and TRV SCHEMATIC DIAGRAM
Temperature Control
(M) 973-214-6886
VALVE SCHEDULE PAGE 1
TRV VALVE SCHEDULE

VALVE BODY ACTUATOR
ITEM EQUIPMENT NAME EQUIPMENT LOCATION APPLICATION LINE SIZE (INCH) VALVE CV PATTERN TYPE CONN. DESCRIPTION
PART NUMBER MANUFACTURER PART NUMBER MANUFACTURER
1 TRV-1 FIRST FLOOR ROOM HEATING STEAM 3/4 2.7 STRAIGHT ON/OFF FPT x MPT 013G8020 DANFOSS 013G8250 DANFOSS RA 2000 THERMOSTATIC RADIATOR VALVES
2 TRV-2 102 HALLWAY HEATING STEAM 3/4 2.7 STRAIGHT ON/OFF FPT x MPT 013G8020 DANFOSS 013G8250 DANFOSS RA 2000 THERMOSTATIC RADIATOR VALVES
3 TRV-3 102 HALLWAY HEATING STEAM 3/4 2.7 STRAIGHT ON/OFF FPT x MPT 013G8020 DANFOSS 013G8250 DANFOSS RA 2000 THERMOSTATIC RADIATOR VALVES
4 TRV-4 SW3 STAIRWELL (FIRST FLOOR) HEATING STEAM 3/4 2.1 SIDE MOUNT ANGLE ON/OFF FPT x MPT 013G8018 DANFOSS 013G8250 DANFOSS RA 2000 THERMOSTATIC RADIATOR VALVES
5 TRV-5 SW2 STAIRWELL (FIRST FLOOR) HEATING STEAM 3/4 2.1 SIDE MOUNT ANGLE ON/OFF FPT x MPT 013G8018 DANFOSS 013G8250 DANFOSS RA 2000 THERMOSTATIC RADIATOR VALVES
6 TRV-6 MAIN ENTRANCE 1 HEATING STEAM 3/4 2.1 SIDE MOUNT ANGLE ON/OFF FPT x MPT 013G8018 DANFOSS 013G8250 DANFOSS RA 2000 THERMOSTATIC RADIATOR VALVES
7 TRV-7 MAIN ENTRANCE 2 HEATING STEAM 3/4 2.1 SIDE MOUNT ANGLE ON/OFF FPT x MPT 013G8018 DANFOSS 013G8250 DANFOSS RA 2000 THERMOSTATIC RADIATOR VALVES
8 TRV-8 FIRST FLOOR ROOM HEATING STEAM 3/4 2.7 STRAIGHT ON/OFF FPT x MPT 013G8020 DANFOSS 013G8250 DANFOSS RA 2000 THERMOSTATIC RADIATOR VALVES
9 TRV-9 SW4 STAIRWELL HEATING STEAM 3/4 2.1 SIDE MOUNT ANGLE ON/OFF FPT x MPT 013G8018 DANFOSS 013G8250 DANFOSS RA 2000 THERMOSTATIC RADIATOR VALVES
10 TRV-10 SW1 STAIRWELL HEATING STEAM 3/4 2.1 SIDE MOUNT ANGLE ON/OFF FPT x MPT 013G8018 DANFOSS 013G8250 DANFOSS RA 2000 THERMOSTATIC RADIATOR VALVES
11 TRV-11 117 OFFICE HEATING STEAM 3/4 2.1 SIDE MOUNT ANGLE ON/OFF FPT x MPT 013G8018 DANFOSS 013G8250 DANFOSS RA 2000 THERMOSTATIC RADIATOR VALVES
12 TRV-12 118 CLASSROOM BATHROOM HEATING STEAM 3/4 2.1 SIDE MOUNT ANGLE ON/OFF FPT x MPT 013G8018 DANFOSS 013G8250 DANFOSS RA 2000 THERMOSTATIC RADIATOR VALVES
13 TRV-13 150 MULTIPURPOSE ROOM HEATING STEAM 1" 2.8 STRAIGHT ON/OFF FPT x MPT 013G8025 DANFOSS 013G8250 DANFOSS RA 2000 THERMOSTATIC RADIATOR VALVES
14 TRV-14 150 MULTIPURPOSE ROOM HEATING STEAM 1" 2.8 STRAIGHT ON/OFF FPT x MPT 013G8025 DANFOSS 013G8250 DANFOSS RA 2000 THERMOSTATIC RADIATOR VALVES
15 TRV-15 213 CLASSROOM HEATING STEAM 3/4 2.7 STRAIGHT ON/OFF FPT x MPT 013G8020 DANFOSS 013G8250 DANFOSS RA 2000 THERMOSTATIC RADIATOR VALVES
16 TRV-16 206 CLASSROOM HEATING STEAM 3/4 2.7 STRAIGHT ON/OFF FPT x MPT 013G8020 DANFOSS 013G8250 DANFOSS RA 2000 THERMOSTATIC RADIATOR VALVES
17 TRV-17 GT212 WOMENS RESTROOM HEATING STEAM 3/4 2.7 STRAIGHT ON/OFF FPT x MPT 013G8020 DANFOSS 013G8250 DANFOSS RA 2000 THERMOSTATIC RADIATOR VALVES

CLIENT
Fairfield, NJ 07004
Building Automation and VALVE SCHEDULE PAGE 1
Temperature Control
(M) 973-214-6886
FTR VALVE SCHEDULE

VALVE BODY ACTUATOR
ITEM EQUIPMENT NAME EQUIPMENT LOCATION APPLICATION LINE SIZE (INCH) VALVE CV PATTERN TYPE CONN. DESCRIPTION
PART NUMBER MANUFACTURER PART NUMBER MANUFACTURER
1 FTR-1 G5 MULTIPURPOSE ROOM HOT WATER 3/4" 2-Way NPT
2 FTR-2 107 TEACHERS LOUNGE HEATING STEAM 1/2 3.5 2-Way ON/OFF NPT ERVS2223 Erie ERAH24A020 Erie Erie 2 POS HI TEMP NO/FO 24V
3 FTR-3 106 MAIN OFFICE HEATING STEAM 1/2 3.5 2-Way ON/OFF NPT ERVS2223 Erie ERAH24A020 Erie Erie 2 POS HI TEMP NO/FO 24V
4 FTR-4 103 PRINCIPAL HEATING STEAM 1/2 3.5 2-Way ON/OFF NPT ERVS2223 Erie ERAH24A020 Erie Erie 2 POS HI TEMP NO/FO 24V
5 FTR-5 111 CLASSROOM HEATING STEAM 1/2 3.5 2-Way ON/OFF NPT ERVS2223 Erie ERAH24A020 Erie Erie 2 POS HI TEMP NO/FO 24V
6 FTR-6 115 NURSE HEATING STEAM 1/2 3.5 2-Way ON/OFF NPT ERVS2223 Erie ERAH24A020 Erie Erie 2 POS HI TEMP NO/FO 24V
7 FTR-7 205 GUIDANCE HEATING STEAM 1/2 3.5 2-Way ON/OFF NPT ERVS2223 Erie ERAH24A020 Erie Erie 2 POS HI TEMP NO/FO 24V
8 FTR-8 215 RESOURCE HEATING STEAM 1/2 3.5 2-Way ON/OFF NPT ERVS2223 Erie ERAH24A020 Erie Erie 2 POS HI TEMP NO/FO 24V
9 RWF-1 110 CLASSROOM HEATING STEAM 3/4" 5 2-Way ON/OFF NPT ERVS2325 Erie ERAH24A020 Erie Erie 2 POS HI TEMP NO/FO 24V
11 RWF-3 120A CLASSROOM HEATING STEAM 3/4" 5 2-Way ON/OFF NPT ERVS2325 Erie ERAH24A020 Erie Erie 2 POS HI TEMP NO/FO 24V
12 RWF-4 120B CLASSROOM HEATING STEAM 3/4" 5 2-Way ON/OFF NPT ERVS2325 Erie ERAH24A020 Erie Erie 2 POS HI TEMP NO/FO 24V

CLIENT
Fairfield, NJ 07004
Temperature Control
(M) 973-214-6886
VALVE SCHEDULE
SYSTEM DATA WATER DATA VALVE BODY DATA ACTUATOR DATA
DESIGN DESIGN
ITEM EQUIPMENT NAME VALVE TAG SERVICE OR LINE SIZE PRESSURE COMBINE PART NO DESCRIPTION
QTY EQUIPMENT LOCATION FLOW PRESSURE SIZE (IN) CALCULATED CV VALVE CV PATTERN TYPE CONN. PART NUMBER TRIM MANUFACTURER PART NUMBER MANUFACTURER
APPLICATION (INCH) DROP
(GPM) DROP(PSI)
1 UV-1 V-1 1 G6-MUSIC HOT WATER VALVE
2 UV-2 V-2 1 G2-MULTIPURPOSE ROOM 3 HOT WATER VALVE
3 UV-3 V-3 1 G2-MULTIPURPOSE ROOM 2 HOT WATER VALVE
4 UV-4 V-4 1 G2-CLASSROOM HOT WATER VALVE
8 AHU V-8 1 G-14 MECH STEAM VALVE
9 AHU V-9 1 158-STORAGE STEAM VALVE
10 AHU V-10 1 156-STORAGE STEAM VALVE
11 HWS V-11 1 BOILER ROOM STEAM VALVE
12 DHWS V-12 1 BOILER ROOM STEAM VALVE
* VALVES WILL BE SELECTED ONCE DATA IS AVAILABLE.

CLIENT
Fairfield, NJ 07004
Temperature Control
(M) 973-214-6886
MASTER BILL OF MATERIAL
MASTER BILL OF MATERIAL

Item # Application Tag Part No. Quantity Shipped Description Manufacturer
1 JACE JACE-1 WEB-8000 1 Base unit includes two isolated RS485 ports, two 10/100MB Ethernet ports, USB Backup & Restore and WiFi connectivity Honeywell
2 Device License Device NC-8025 1 Up to 25 devices/1250 point core Honeywell
3 SMA SMA SSMA-8025-1YR-INIT 1 One Year Software Maintenance Agreement for 8025 Core (18 month initial period only) Honeywell
4 Network Switch NS-1 EISK5-100T 1 5 Ports 10/100 Mbps Skorpion switch. Contemporary Controls
7 Programmable Controller C-1 PUB6438S 12 Honeywell Spyder Controller with 6UI, 4DI, 3AO, 8DO Honeywell
8 Outside Air Temperature OAT A/20K-O-4X 1 OA Temp, 20k temp. NEMA 4x ACI
9 Discharge air temperature DAT A/20K-D-12"-GD 7 ACI, 12" 20K Duct Temp Sensor for AHU Supply Air Temp ACI
10 ZONE Temp Sensor ZNT/CO2 TR42-CO2 1 TR42 LCD Wall module, Temperature WITH CO2, two-wire Sylk Honeywell
11 ZONE Temp Sensor ZNT-# A/20K-R2S 25 ACI, 20K Room Temp sensor, set point ACI
13 Averaging duct Temperature MAT A/20K-FA-24'-PB 2 Thermistor, Flexible Cable Averaging, 20K ohm NTC, 24', Plastic Box ACI
14 Discharge air temperature DAT TE-DFN-F0848-00 7 Air Duct Temperature Sensor, 8 inch probe, 20K Ohm Thermistor. Dwyer
15 Immersion Temp Sensor TS-# A/20K-I-2.5"-GD 2 20K Ohm Thermistor, Immersion, 2.5", Galvanized Enclosure ACI
16 Steam Pressure Transmitter SP 626-08-CB-P1-E5-S5 1 Pressure Transmitter, 0-10VDC, 3 wire, 0-30 psig, 1/4" NPT male process connection Dwyer
17 Stainless Steel Siphons - A-170-A 1 1/4" NPT male, both side, Siphon, SS Dwyer
18 Stainless Steel Fitting - A-2021-2 1 1/4" NPT female connection both side for connecting siphon and pressure transmitter Dwyer
22 Field Mount Relay FR-# RIBU1C 32 Universal RIB Relay Functional Devices
24 Power Supply for JACE PSH-# PSH75AB10 1 Enclosed Single 75VA, 120 to 24 Vac, UL Class 2 Power Supply, 10Amp main breaker Functional Devices

CLIENT
Fairfield, NJ 07004
Building Automation and MASTER BILL OF MATERIAL
Temperature Control
(M) 973-214-6886

Renaissance Middle School Control Submittal 05-20-2022

Uploaded by

Copyright:

Available Formats

Renaissance Middle School Control Submittal 05-20-2022

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Renaissance Middle School Control Submittal 05-20-2022

Uploaded by

Copyright:

Available Formats

TITLE PAGE

RENAISSANCE MIDDLE SCHOOL

FACILITY MONTCLAIR SCHOOL DISTRICT PROJECT: RENAISSANCE MIDDLE SCHOOL

FACILITY MONTCLAIR SCHOOL DISTRICT PROJECT: RENAISSANCE MIDDLE SCHOOL

GENERAL NOTES HVAC SYSTEM LEGEND:

MOTOR OPERATED DAMPER FREEZESTAT (D.P. CONTACT)

TEMPERATURE CONTROL LEGEND:

Low Voltage, 18 AWG, Copper Wire

NO CO2 CO2 SENSOR

Line Voltage, THHN Field Wiring

FACILITY MONTCLAIR SCHOOL DISTRICT PROJECT: RENAISSANCE MIDDLE SCHOOL

RAD TYPE-2 PANEL

PUB6438S PUB6438SR PUB6438S PUB6438S

RAD TYPE-3 PANEL RAD TYPE-1 PANEL AHU AHU

PUB6438S PUB6438S PUB6438S PUB6438S PUB6438S PUB6438S PUB6438S PUB6438S PUB6438S

HWS UV-1 UV-2 UV-3 UV-4 UV-5 UV-6 AHU UV-7

FACILITY MONTCLAIR SCHOOL DISTRICT PROJECT: RENAISSANCE MIDDLE SCHOOL

RENAISSANCE MIDDLE SCHOOL

FACILITY MONTCLAIR SCHOOL DISTRICT PROJECT: RENAISSANCE MIDDLE SCHOOL

UV-7 UV-6 UV-5

FACILITY MONTCLAIR SCHOOL DISTRICT PROJECT: RENAISSANCE MIDDLE SCHOOL

TRV-11 TRV-5 FTR-6 FTR-5

FACILITY MONTCLAIR SCHOOL DISTRICT PROJECT: RENAISSANCE MIDDLE SCHOOL

TRV-15 TRV-17 TRV-16

RWF-10 RWF-9 RWF-8 RWF-7 RWF-6

FACILITY MONTCLAIR SCHOOL DISTRICT PROJECT: RENAISSANCE MIDDLE SCHOOL

*OUTSIDE AIR TEMPERATURE

FACILITY MONTCLAIR SCHOOL DISTRICT PROJECT: RENAISSANCE MIDDLE SCHOOL

PANEL CONTINUED ON NEXT PAGE

LOCATION : BOILER ROOM

FACILITY MONTCLAIR SCHOOL DISTRICT PROJECT: RENAISSANCE MIDDLE SCHOOL

TS-2 HW RETURN TEMPERATURE C3

TS-1 HW SUPPLY TEMPERATURE C3 36 COM

BLR-2 ALM BOILER 30 DI-4 DO-2 10 12

BLR-1 STS BOILER 25 COM

LOCATION : BOILER ROOM

FACILITY MONTCLAIR SCHOOL DISTRICT PROJECT: RENAISSANCE MIDDLE SCHOOL

1.1 STEAM HEATING SYSTEM SEQUENCE:

B. BOILER LEAD/LAG OPERATION:

C. STEAM PRESSURE SETPOINT:

B.SYSTEM ON/OFF AND PUMP CONTROL:

C.TEMPERATURE CONTROL – NORMAL OPERATION:

FACILITY MONTCLAIR SCHOOL DISTRICT PROJECT: RENAISSANCE MIDDLE SCHOOL

HOT WATER SYSTEM BILL OF MATERIAL

FACILITY MONTCLAIR SCHOOL DISTRICT PROJECT: RENAISSANCE MIDDLE SCHOOL

FACILITY MONTCLAIR SCHOOL DISTRICT PROJECT: RENAISSANCE MIDDLE SCHOOL

ZONE TEMP SENSOR

FACILITY MONTCLAIR SCHOOL DISTRICT PROJECT: RENAISSANCE MIDDLE SCHOOL

DISCHARGE AIR C3 36 COM

LOCATION : G14 MECH

FACILITY MONTCLAIR SCHOOL DISTRICT PROJECT: RENAISSANCE MIDDLE SCHOOL

AHU SEQUENCE OF OPERATION

FACILITY MONTCLAIR SCHOOL DISTRICT PROJECT: RENAISSANCE MIDDLE SCHOOL

AHU BILL OF MATERIAL

FACILITY MONTCLAIR SCHOOL DISTRICT PROJECT: RENAISSANCE MIDDLE SCHOOL

20" 18" 1" 1"

FACILITY MONTCLAIR SCHOOL DISTRICT PROJECT: RENAISSANCE MIDDLE SCHOOL

FACILITY MONTCLAIR SCHOOL DISTRICT PROJECT: RENAISSANCE MIDDLE SCHOOL

DISCHARGE AIR C3 36 COM

MAT 32 UI-1 C4 WHT/YEL FR-2 BLU