PM150

DC-DC Converter

PM150-series 120 to 150 W

Input / Output Operation
• Wide input voltage ranges. • Operating temperature range -25 to +55 °C
• Input ranges from 10 to 270 Vd.c. and +70 ° with derating.
• Single outputs from 12 to 48 Vd.c. • High efficiency.
• Reverse input voltage protection. • Fully encapsulated, meets IP20 as standard.
• 2.5 kVa.c. isolation input/output, • Convection cooled.
input/case, output/case. • Output voltage adjustable on frontpanel.

Features EMC
• Overvoltage protection OVP. • EN/IEC 61000-6-3, Emission.
• Extra output with series diode. • EN/IEC 61000-6-2, Immunity.
• Over/Under voltage alarm relay. • EN/IEC 61000-4-4, 4 kV.
• EN/IEC 61000-4-5 level 2 & 3.

Input and outputs ratings

Nominal inputs Input range Code Output
12, 24 Vd.c. 10 - 30 V A Voltage Current Power
24, 28, 36, 48 Vd.c. 20 - 60 V B 12 V 10 - 12 A 120 - 150 W
72, 96, 110, 127 Vd.c. 50 - 150 V C 13.8 V 8.7 - 10.9 A 120 - 150 W
110, 127, 220 Vd.c. 90 - 270 V D 15 V 8 - 10 A 120 - 150 W
24V 5 - 6.25 A 120 - 150 W
Input voltages meeting train standard
EN 50155/IEC 60571, can be made on demand. 28 V 5.36 A 150 W
36 V 4.17 A 150 W
48 V 2.5 - 3.13 A 120 - 150 W
Output ratings and type code
Output Input
Voltage Current Power 10 - 30 V 20 - 60 V 50 - 150 V 90 - 270 V How to read our product code:
Example PM150B12
12 V 10.0 A 120 W PM150A12
PM150 = Family code
12 V 12.5 A 150 W PM150B12 PM150C12 PM150D12 B = input voltage code B
13.8 V 8.70 A 120 W PM150A13.8 12 = Output voltage 12V
13.8 V 10.9 A 150 W PM150B13.8 PM150C13.8 PM150D13.8
15 V 8.00 A 120 W PM150A15
15 V 10.0 A 150 W PM150B15 PM150C15 PM150D15
24 V 5.00 A 120 W PM150A24
24 V 6.25 A 150 W PM150B24 PM150C24 PM150D24
28 V 5.36 A 150 W PM150B28 PM150C28 PM150D28
36 V 4.17 A 150 W PM150B36
48 V 2.50 A 120 W PM150A48
48 V 3.13 A 150 W PM150B48 PM150C48 PM150D48

Features Optional Features

Overvoltage protection OVP Inrush current limit with NTC

The output voltage is limited to 15 % over Reduces the inrush current during start up.
nominal output voltage by an extra The input voltage range will be affected.
regulation circuit. Only available on C & D inputs.
Conformally coating
Extra output with series diode For environment with high non condensing
Use the series diode output when the output humidity max 98 % RH.
is connected in parallel with other power +70 °C operating temperature
supplies to archive redundancy. Contact factory for derating as it depends on
model. The alarm can not be used at +70 °C.
Over / Under voltage alarm Mounting brackets L214-1
The built in relay changes to alarm state if Se figure 3.
the converter output voltage is not within 19” Rack mounting set PL88-2
90 to 115 % of nominal output. To mount two PM150 together to form a
The user can select NO or NC relay full 19” rack unit, see figure 2.
function. The relay rating is 19” Rack mounting bracket PL88-3
30 V 0.5 A (d.c. or a.c.) To mount one PM150 to form a full 19” rack
unit, see figure 2.
EN/IEC 61000-4-5 level 4
External varistor + surge arrestor mounted from
pole to ground. With this filter the input meets
level 4 of EN/IEC 61000-4-5 (+/-2 kV line to
line, 4 kV line to ground)
DIN-rail clips
Clips to mount PM150 on a 35 mm DIN-rail.
(Used with PL88-1 & L-214 see figure 3)
Train input
Input voltage range according to train standard
EN 50155 and IEC 60571.

Polyamp AB PM150 DC-DC Converters Page 2

General data / input data Output data

Design topology Push-Pull Source regulation 0.1 %

Switching frequency 30 kHz Load regulation (0 to 100 % load) 0.3 %
Emission / Immunity See page 4 Transient recovery time for
Safety EN/IEC 60950 Class I 10 to 90 % load step to within 3 % of
nominal output voltage. <3 ms
Max. accepted input ripple1
50-400 Hz 2 % of nominal voltage Output ripple (60 kHz) 2
30 mV p-p

Input power at no load Max. 9 W Input ripple attenuation to output

(50 to 400 Hz) 150:1
Inrush current limit No
Emission / Immunity See page 4
Reverse input voltage protection
Temperature coefficient 0.02 %/°C
A, B inpute code Parallel diode
Min output adjustment range
C, D input code Series diode adjustable with a 15 turn
Dimensions (D x W x H) 160 x 214 x 88 mm potentiometer 95 - 110 %
Weight 2.5 kg Current limit, rectangular. 105 %

1. Higher ripple affects the input, contact factory Remote sense No

Soft start Yes
Start-up time 1s
Hold-up time, contact factory 2 - 25 ms
2. The output ripple might increase to 0.5 % RMS of Vout,
Efficiency 3
80 - 88 %
when EN/IEC 61000-4-3, 10 V/m test is applied
3. Lowest efficiency measured within the whole input Operating temperature range
voltage range at 100 % load. at 100 % load. -25 to +55 °C
(Convection cooling) with derating4 +70 °C
4. Contact factory for derating as it depends on model.
The alarm relay can not be used at +70 °C. Storage temperature range -40 to +85 °C

Mechanical drawing 88 mm

214 mm mm
160

Figure 1. Dimensions Weight: 2.5 kg

2 units PM150/240 mounted PM150/240 wall mounted. PM150/240 wall mounted.

side by side forming one 19” unit Using mounting brackets Using standard brackets
using standard bracket PL88-1 and (Optional) L214-1 PL88-1
PL88-2 (Optional).
4 units PM150/240 mounted
verticaly using standard PL88-1
brackets and L480-2 (Optional).
Single unit PM150/240
mounted as one 19” unit using
PL88-3 brackets (Optional).

Figure 3. Wall and chassis mounting

Figure 2. 19”-rack mounting
Polyamp AB PM150 DC-DC Converters Page 3
Safety and EMC Safety standard EN/IEC 60950

PM150 meets the requirements defined by Isolation testable levels Test voltage
CE mark as apparatus. Input / Output 2.5 kVa.c. / 4 kVd.c.
PM150 meets requirements of EMC directive Input / Case 2.5 kVa.c. / 4 kVd.c.
and low voltage directive (LVD). Output / Case all outputs 2.5 kVa.c. / 4 kVd.c.
Thus a PM150 can be used as free standing unit Input / Alarm 2.5 kVa.c. / 4kVd.c.
or in installations as well as systems designed Output / Alarm 2.5 kVa.c. / 4 kVd.c.
according to ”The modular approach”. PM150 case / Alarm 2.5 kVa.c. / 4 kVd.c.
can be used in installation without further EMC
We use the product standard Low voltage
tests, if our installation instructions are followed.
power supplies, DC outputs EN/IEC 61204-3
Please note that product standards can demand
and the generic EMC standards:
different levels or other basic standard tests. We
EN/IEC 61000-6-2 (Immunity)
test according to levels below. For higher levels
EN/IEC 61000-6-3 (Emission)
or other tests, contact factory.

EMC
EMC-standards EMC-performance
Emission standards Input Output Remarks
EN 55011/EN 55022 (0.15-30 MHz) Level B Level B
EN 55011/EN 55022 (30-1000 MHz) Level B Enclosure test
Immunity standards EN/IEC 61000-6-2
EN/IEC 61000-4-2 8 kV / 15 kV Contact / air, Enclosure test
EN/IEC 61000-4-3 10 V/m AM-Modulated Output ripple can increase to
0.5 % of Vout Enclosure test
EN/IEC 61000-4-4 4 kV 4 kV
EN/IEC 61000-4-5, Input code A, B 0.5 kV / 1 kV 0.5 kV / 1 kV Line-line 2 Ω / Line-case 12 Ω
EN/IEC 61000-4-5, Input code C, D 1 kV / 2 kV1 0.5 kV / 1 kV
EN 50121-3-2/IEC 62236-3-2 1 kV / 2 kV 1 kV / 2 kV Line-line 42 Ω / Line-case 42 Ω
EN/IEC 61000-4-6 10 VRMS 10 VRMS AM-Modulated
EN/IEC 61000-4-8 Not sensitive Enclosure test
EN/IEC 61000-4-10 Not sensitive Enclosure test
1 Higher level 2 kV / 4 kV with external filters, contact factory.

Contact

For updates on this datasheet we refer to www.polyamp.com

Specifications subject to change without notice.

Distributor

Polyamp AB Box 229 597 25 Åtvidaberg Sweden

Telephone: +46 120 854 00 Telefax: +46 120 854 05
http://www.polyamp.com
E-mail: info@polyamp.se

Polyamp AB 10262-8 PM150 DC-DC Converters Page 4