Miniature Industrial Relays: Contact Data

R2N
miniature industrial relays

R2N (AC) R2N (DC)
• Relays of general application
• For plug-in sockets: on 35 mm rail mount acc. to EN 60715;
12 A / 250 V AC on panel mounting; with terminals for soldering
• AC and DC coils, insulation class F: 155 °C
• WT (mechanical indicator + lockable front test button)
- standard equipment of relays. Relays may be provided
with the test buttons (no latching) and plugs - page 8
5HFRJQLWLRQVFHUWL¿FDWLRQVGLUHFWLYHV5R+6
Contact data
Number and type of contacts 2 CO
Contact material AgNi, AgNi/Au ÀDVKJROGSODWLQJ
Rated / max. switching voltage AC 250 V / 440 V
Min. switching voltage 10 V
Rated load (capacity) AC1 12 A / 250 V AC
AC15 3 A / 120 V 1,5 A / 240 V (B300)
DC1 12 A / 24 V DC (see Fig. 3)
DC13 0,22 A / 120 V 0,1 A / 250 V (R300)
Motor load acc. to UL 508 1/2 HP 240 V AC, 4,9 FLA, single-phase motor ❶
AC3 acc. to IEC 60947-4-1 0,37 kW 240 V AC, single-phase motor
Min. switching current 5 mA
Max. inrush current 24 A
Rated current 12 A
Max. breaking capacity AC1 3 000 VA
Min. breaking capacity 0,3 W
Contact resistance Pȍ
Max. operating frequency • at rated load AC1 1 200 cycles/hour
• no load 12 000 cycles/hour
Coil data
Rated voltage 50/60 Hz AC 6, 12, 24, 42, 48, 60, 80, 110, 115, 120, 127, 220, 230, 240 V
DC 5, 6, 12, 24, 48, 60, 80, 110, 125, 220 V
Must release voltage AC: 8n DC: 8n
Operating range of supply voltage see Tables 1, 2 and Fig. 4, 5
Rated power consumption AC 1,6 VA
DC 0,9 W
Insulation according to EN 60664-1
Insulation rated voltage 250 V AC
Rated surge voltage 4 000 V 1,2 / 50 μs
Overvoltage category III
Insulation pollution degree 3
Dielectric strength • between coil and contacts 2 500 V AC type of insulation: basic
• contact clearance 1 500 V AC type of clearance: micro-disconnection
• pole - pole 2 500 V AC type of insulation: basic
Contact - coil distance • clearance PP
• creepage PP
General data
Operating / release time (typical values) AC: 10 ms / 8 ms DC: 13 ms / 3 ms
Electrical life • resistive AC1 > 105 12 A, 250 V AC
FRVĳ see Fig. 2
Mechanical life (cycles) > 2 x 107
Dimensions (L x W x H) 27,4 x 21 x 35,5 mm
Weight 35 g
Ambient temperature • storage -40...+85 oC
(non-condensation and/or icing) • operating AC: -40...+55 oC DC: -40...+70 oC
Cover protection category IP 40 EN 60529
Environmental protection RTI EN 61810-7
Shock resistance (NO/NC) 10 g / 5 g
Vibration resistance 5 g 10...150 Hz
23.12.2020
The data in bold type relate to the standard versions of the relays.
❶ For single phase motors for 110-120 V AC do not use motors with higher FLA than given for 240 V AC.
www.relpol.com.pl Export Sales Department phone +48 68 47 90 832, 951 • e-mail: export@relpol.com.pl
R2N
Design Dimensions - plug-in version (WT),

with lockable front test button type T
6,3 6,3 4,14,2

35,5
27,4
6,6 6,6
6,2
21
Improvement of the functionality of the mechanical

indicator (W): it is mounted on an insulation base of
the unit of the movable contacts; the changes provide
Dimensions - plug-in version, with test button
the appropriate position in the window in the upper side (no latching) or with plug (no manual operation)
of the housing irrespectively of the number of operations
performed by the relay.
6,3 6,3 4,14,2

35,5
27,4
6,6 6,6
6,2
21
Application of electronics made in the SMD techno-

Test buttons R4P-0001 and plugs R4W-0003 need
logy: additional equipment L (LED diode) and D (diode) to ordered saparately. They substitute buttons type T.
are located on the printed circuit board; the change To exchange by Customer themselves. Information
on test buttons (no latching) and plugs - page 8.
of the position of the LED diode and optimization
of the quality and intensity of its light provide certainty
that the relay is in operation status when the LED is on.
Connection diagram (pin side view)
2 CO
,PSURYHPHQWRIWKHHႈFLHQF\RIWKHHOHFWURPDJQHW
an innovational technology of connecting elements has Note: the indicated polarization of the supply refers to the
relays with extra equipment D - surge suppression element
been introduced, which guarantees more reliable opera- (diode) - for DC coils only.
23.12.2020
tion of the relay.

Strengthening of the insulation in the area of the
contact plate: polyamide PA66 has been applied; it has
very good mechanical and electrical parameters and best
thermal properties. 2
R2N
Mounting, sockets and accessories for relays
Relays R2N are designed for mounting in plug-in sockets. With WT equipment as standard (W - mechanical
indicator + T - lockable front test button). In these relays is possibility self-exchange of button type T for test
button R4P-0001 (no latching) or on plug R4W-0003 (no manual operation). The buttons R4P-0001 and the plugs
R4W-0003 need to ordered saparately.
Accessories
Sockets Retainer Spring Description Additional
for R2N / retractor clips wire clips plates equipment
Screw terminals sockets, 35 mm rail mount (acc. to EN 60715) or on panel mounting (two M3 screws)
GZT2 GZT4-0040 G4 1052 GZT4-0035 M... ❸, ZGGZ4 ❹
GZM2 GZT4-0040 G4 1052 GZT4-0035 M... ❸, ZGGZ4 ❹
Push-in terminals sockets, 35 mm rail mount (acc. to EN 60715) or on panel mounting (two M3 screws)
GZP4-0400, M... ❸, ZGZP4-8,
GZP4 ❷ G4 1052 MP15
GZT4-0040 ZGZP4-2, ZGZP-2 ❹
Sockets for PCB
SU4/2D – G4 1053 – –
Solder terminals sockets
SU4/2L – G4 1053 – G4 1040 ❺
G4/2 – G4 1053 – –
❷ Sockets GZP4: wire connection - see page 10. ❸ Signalling / protecting modules type M... - see page 12.
❹ Interconnection strips ZGGZ4, ZGZP... - see page 13-14. ❺ Spring clamps G4 1040.
Electrical life at AC resistive load. Fig. 1 Electrical life reduction factor Fig. 2
Switching frequency: 1 200 cycles/hour at AC inductive load
N
Number of cycles
Reduction factor
Power factor
N - electrical life
Breaking capacity [kVA] at AC1
23.12.2020
R2N
Max. DC resistive load breaking capacity Fig. 3 Coil operating range - DC Fig. 4
In = 12 A
DC current [A]
U / Un
1
B
A
DC voltage [V] Ambient temperature [°C]
Coil operating range - AC 50 Hz Fig. 5 Description of Fig. 4 and 5

A - relations between make voltage and ambient temperature at
no load on contacts. Coil temperature and ambient temperature
are equal before coil energizing. Make voltage is not higher than
In = 12 A the value read on Y axis (multiplication of rated voltage).
B - relations between make voltage and ambient temperature
1 after initial coil heating up with 1,1 Un, at continues load of In on
U / Un
contacts. Make voltage is not higher than the value read on Y

axis (multiplication of rated voltage).
1, 2 - values on Y axis represent allowed overvoltage on coil at
2 certain ambient temperature and contact load:
1 - no load
2 - rated load
Ambient temperature [°C]
GZP4
Push-in terminals
plug-in sockets
for R2N, R4N
- see page 10
23.12.2020
R2N
&RQWDFWPDWHULDOVHOHFWLRQIRUGLႇHUHQWORDGW\SHV
• AgNi - for resistive or inductive loads,

• $J1L$XÀDVKJROGSODWLQJ - Au protects the contact surface during storage.
Coil data - DC voltage version Table 1
Coil resistance Coil operating range

Rated voltage Acceptable
Coil code at 20 °C V DC
V DC resistance
ȍ min. (at 20 °C) max. (at 70 °C)
1005 5 28 ± 10% 4,0 5,5
1006 6 40 ± 10% 4,8 6,6
1012 12 160 ± 10% 9,6 13,2
1024 24 640 ± 10% 19,2 26,4
1048 48 2 600 ± 10% 38,4 52,8
1060 60 4 000 ± 10% 48,0 66,0
1080 80 7 100 ± 10% 64,0 88,0
1110 110 13 600 ± 10% 88,0 121,0
1125 125 16 000 ± 10% 100,0 137,5
1220 220 54 000 ± 10% 176,0 242,0
Coil data - AC 50/60 Hz voltage version Table 2
Coil resistance Coil operating range

Rated voltage Acceptable
Coil code at 20 °C V AC
V AC resistance
ȍ min. (at 20 °C) max. (at 55 °C)
5006 6 9,8 ± 10% 4,8 6,6
5012 12 39,5 ± 10% 9,6 13,2
5024 24 158 ± 10% 19,2 26,4
5042 42 470 ± 10% 33,6 46,2
5048 48 640 ± 10% 38,4 52,8
5060 60 930 ± 10% 48,0 66,0
5080 80 1 720 ± 10% 64,0 88,0
5110 110 3 450 ± 10% 88,0 121,0
5115 115 3 610 ± 10% 92,0 127,0
5120 120 3 770 ± 10% 96,0 132,0
5127 127 4 000 ± 10% 101,6 139,0
5220 220 15 400 ± 10% 176,0 242,0
5230 230 16 100 ± 10% 184,0 253,0
5240 240 16 800 ± 10% 192,0 264,0
Relays for railroad industry

PIR2T R2T
R
- interface - industrial
23.12.2020
R2N
Ordering codes
Cover protection
category
Type Contact Number and type Connection Coil code Additional

material of contacts mode equipment
R 2 N — — — —
Contact material
20 - AgNi
21$J1L$XÀDVKJROGSODWLQJ see Tables 1, 2 page 5
Number and type of contacts
12 - 2 CO
Cover protection category
2 - in cover, IP 40 version
Connection mode
3 - for plug-in sockets
Additional equipment ❻
without marks - without additional equipment
WT - mechanical indicator + lockable front test button
WTL - mechanical indicator + lockable front test button + light indicator (LED diode)
WTD - mechanical indicator + lockable front test button + surge suppression element (diode)
WTLD - mechanical indicator + lockable front test button + light indicator (LED diode) + surge suppression element (diode)
❻ T - orange colour (AC coils), green (DC coils). WT - standard equipment of relays. WTD, WTLD - available only in relays with DC coils.
Test buttons (no latching) and plugs need to ordered saparately. They substitute buttons type T. To exchange by Customer themselves.
Information on test buttons (no latching) and plugs - page 8.
• Button R4P-0001-A - orange colour (AC coils)
• Button R4P-0001-D - green colour (DC coils)
• Plug R4W-0003-A - orange colour (AC coils)
• Plug R4W-0003-D - green colour (DC coils)
Note:
While the relay operates, the test button of the T type becomes heated. In order to push the test button manually, you
VKRXOG¿UVWWXUQWKHVXSSO\YROWDJHRႇDQGZDLWVRPHWLPHXQWLOWKHEXWWRQEHFRPHVFROGHU RUSXVKWKHEXWWRQLPPH-
diately using a protective glove or an insulated tool). The button shall be pushed smoothly and quickly. The normally
open contacts are closed with the button for the time during which the button is pushed. Releasing the button opens
the normally open contacts. Normally open contacts may be closed with the blocking function of the button (it shall be
turned by 90°). When the button is turned back, the normally open contacts are opened.
For relays with additional equipment DVXUJHVXSSUHVVLRQHOHPHQW GLRGH YHUVLRQV:7'DQG:7/' ¿[HGVXSSO\
polarization compulsory for the DC load of coils: +A1(13) / -A2(14). The polarization is indicated on the relay cover.
For other versions of the relays with DC coils any polarization is possible.
Example of ordering codes:

R2N-2012-23-1024-WT relay R2N, for plug-in sockets, two changeover contacts, contact material AgNi, coil
voltage 24 V DC, with mechanical indicator and lockable front test button, in cover IP 40
23.12.2020
Additional equipment for industrial relays
Industrial relays for plug-in sockets: R2N, R3N, R4N, R15 - 2 CO ❷, R15 - 3 CO ❷ with WT equipment as stan-
dard (W - mechanical indicator + T - lockable front test button). Detailed information on additional equipment
of individual relays can be found in the data sheets on the side of ”Ordering codes”.
Note:
While the relay operates, the test button of the T type becomes heated. In order to push the test button manually, you
VKRXOG¿UVWWXUQWKHVXSSO\YROWDJHRႇDQGZDLWVRPHWLPHXQWLOWKHEXWWRQEHFRPHVFROGHU RUSXVKWKHEXWWRQLPPH-
diately using a protective glove or an insulated tool). The button shall be pushed smoothly and quickly. The normally
open contacts are closed with the button for the time during which the button is pushed. Releasing the button opens
the normally open contacts. Normally open contacts may be closed with the blocking function of the button (it shall be
turned by 90°). When the button is turned back, the normally open contacts are opened.
Type ❶ Description For industrial relays

W mechanical indicator R2N, R3N, R4N,
(R15 - 2 CO, 3 CO ❷)
T lockable front test button, R2N, R3N, R4N,

orange (AC coils), green (DC coils) (R15 - 2 CO, 3 CO ❷)
L light indicator (LED diode), R2N, R3N, R4N, RY2,

located inside the relay (R15 - 2 CO, 3 CO, 4 CO ❷)
RUC, RUC-M
D surge suppression element (diode) R2N, R3N, R4N, RY2,

- only for DC coils (R15 - 2 CO, 3 CO, 4 CO ❷)
V surge suppression element (varistor) (R15 - 2 CO, 3 CO ❷)

- only for AC coils
K test button without block function, (R15 - 4 CO ❷),

orange (AC coils), green (DC coils) RUC
❶ Available combinations:
WT, WTL, WTD, WTLD - in relays R2N, R3N, R4N for plug-in sockets
L, D, LD - in relays RY2 for plug-in sockets
WT, WTL, WTD, WTLD, WTV, WTLV - in relays R15 - 2 CO, 3 CO for plug-in sockets
K, L, D, KL, KD, LD, KLD - in relays R15 - 4 CO for plug-in sockets
K, L, KL - in relays RUC
L - in relays RUC-M
❷ Voltage versions, in covers
Test buttons type T R2N, R3N, R4N
orange
(AC coils)
green
(DC coils)
23.12.2020
Test buttons (no latching) and plugs
Test buttons (no latching) are recommended for R2N...WT, R3N...WT, Fig. 1
R4N...WT, R15...WT 2 CO, R15...WT 3 CO relays - for applications that do
not allow permanent contact latching. By manual operation (pressing the
button) relay contacts can get switched for as long time as long the button is
pressed. Contacts return to initial position as soon as pressure is released
from the button. Those operations can be done while the coil is deenergized ❸.
Button R4P-0001 or R15-M404 can be easily inserted by the Customer after

removal of button type T (see Fig. 2). Button type T can be removed with
screwdriver as shown on Fig. 1.
❸ While the relay operates, the test button becomes heated. In order to push the test button
PDQXDOO\\RXVKRXOG¿UVWWXUQWKHVXSSO\YROWDJHRႇDQGZDLWVRPHWLPHXQWLOWKHEXWWRQEHFRPHV
colder (or push the button immediately using a protective glove or an insulated tool). The button shall
be pushed smoothly and quickly.
Fig. 2
Dimensions - test button R4P-0001 Dimensions - test button R15-M404

for R2N...WT, R3N...WT, R4N...WT for R15...WT 2 CO, R15...WT 3 CO
Types of buttons: Types of buttons:

R4P-0001-A - orange colour (AC coils) R15-M404-A - orange colour (AC coils)
R4P-0001-D - green colour (DC coils) R15-M404-D - green colour (DC coils)
Plugs R4W-0003 or R15-M203 can substitute button type T if manual operation (latching and testing) is not
allowed. Changing button type T for plug can be done by Customer themselves in the same way as changing button
type T for button (no latching).
Dimensions - plug R4W-0003 Dimensions - plug R15-M203

for R2N...WT, R3N...WT, R4N...WT for R15...WT 2 CO, R15...WT 3 CO
23.12.2020
Types of plugs: Types of plugs:

R4W-0003-A - orange colour (AC coils) R15-M203-A - orange colour (AC coils)
R4W-0003-D - green colour (DC coils) R15-M203-D - green colour (DC coils)
Sockets and accessories
GZT2 Connection diagram Dimensions

For R2N
NO
Screw terminals
Max. tightening moment NC
for the terminal: 0,7 Nm
35 mm rail mount ZGGZ4
acc. to EN 60715
or on panel mounting
76,3 x 27 x 42,5(80) mm ❷
Two poles
12 A, 300 V AC COIL
COM
GZT4-0040 G4 1052
Accessories ❶ GZT4-0035 Module type M...
GZM2 Connection diagram Dimensions

For R2N
COM
Screw terminals NO
Max. tightening moment
for the terminal: 0,7 Nm NC
35 mm rail mount ZGGZ4
acc. to EN 60715
75 x 27 x 61(82) mm ❷
Two poles
12 A, 300 V AC
COIL
GZT4-0040 G4 1052
Accessories ❶ GZT4-0035 Module type M...
❶ Mounting and sub-assemblies of accessories in the socket - see page 9. Signalling / protecting modules type M... - see page 12.
❷ In the bracket the height of socket with retainer / retractor clip is shown.
Mounting and sub-assemblies of the relay and accessories in the socket
Signalling / protecting module Electromagnetic

type M... relay
Retainer / retractor clip
Removing the relay from the socket

with a retrainer / retractor clip
Description plate
23.12.2020
Screw terminals
plug-in socket
GZP4 Connection diagrams Dimensions

For R4N, R2N 41 31 21 11 41 11
COM 12 11 10 9 12 9
Push-in terminals NO
44 34 24 14
8 7 6 5
44
8
14
5
75,8
Max. cross section of the cables: 42 32 22 12 42 12 31 45,9
2 x 1,5 mm2 (ferrules without insulation) NC 4 3 2 1 4 1
2 x 1 mm2 (ferrules with insulation)

Stripping length: 8...10 mm
29,8
35 mm rail mount
acc. to EN 60715
97 x 31 x 45,9(75,8) mm ❷ A2 A1 A2 A1
92,9
35,2
Two poles COIL 14 13 14 13
97
12 A, 300 V AC
R4N R2N
Four poles
8 A, 300 V AC
27,9
The drawings present

inserting wire into the
ZGZP4-8 Push-in terminal and
removing wire using the
button releasing a clamp
(assembly without tools).
GZP4-0400 GZT4-0040 G4 1052 MP15 ZGZP4-2 ZGZP-2 Module type M...
Accessories ❶ Wire connection
❶ Mounting and sub-assemblies of accessories in the socket - see page 9. Signalling / protecting modules type M... - see page 12.
❷ In the bracket the height of socket with retainer / retractor clip is shown.
23.12.2020
10
SU4/2D Pinout Dimensions

For R2N
For PCB
29,6 x 21,5 x 11 mm
Two poles
12 A, 250 V AC
Accessories G4 1053
SU4/2L Dimensions of opening on panel mounting Dimensions

For R2N
Solder terminals
29,6 x 21,5 x 18,1 mm
Two poles
12 A, 250 V AC
Accessories G4 1053 G4 1040
G4/2 Pinout of openings on panel mounting Dimensions

For R2N
Solder terminals
40,5 x 21,5 x 18,1 mm
Two poles
12 A, 250 V AC
Accessories G4 1053
23.12.2020
11
Signalling / protecting modules type M...
For sockets type:

GZT80, GZM80, GZS80, GZP80, GZT92, GZM92, GZS92,
ES 32, GZT2, GZM2, GZT3, GZM3, GZT4, GZM4, GZP4
Modules type M... are parallely connected with relay coil.

Polarization P: -A1/+A2. Polarization N: +A1/-A2.
Modules type M... Layout Voltage Type of module ❶ ❷

Module D (polarization P) 6/230 V DC M21P
It limits overvoltage on DC coils.
Module D (polarization N) 6/230 V DC M21N

It limits overvoltage on DC coils.
Module LD (polarization P) 6/24 V DC M31R, M31G

It limits overvoltage on DC coils. 24/60 V DC M32R, M32G
Coil energizing indication. 110/230 V DC M33R, M33G
Module LD (polarization N) 6/24 V DC M41R, M41G
It limits overvoltage on DC coils. 24/60 V DC M42R, M42G
Coil energizing indication. 110/230 V DC M43R, M43G
Module RC 6/24 V AC/DC M51
It protects against EMC disturbance. 24/60 V AC/DC M52
It limits overvoltage. 110/240 V AC/DC M53
Module L 6/24 V AC/DC M61R, M61G
Coil energizing indication. 24/60 V AC/DC M62R, M62G
110/240 V AC/DC M63R, M63G
Module LV 6/24 V AC/DC M91R, M91G
It limits overvoltage on AC and DC coils. 24/60 V AC/DC M92R, M92G
Coil energizing indication. 110/240 V AC/DC M93R, M93G
Module V 6/24 V AC M71
It limits overvoltage on AC coils. 110/130 V AC M72
No indication. 220/240 V AC M73
Module R 110/240 V AC M103
It limits harmful voltage on AC coils induced in long
lines which causes unwanted making of the relay.
❶ M...R - LED red, M...G - LED green

❷ When ordering modules indicate their color: gray or black.
MODULE type M...
LED red
– M...R
LED green
– M...G
23.12.2020
PRECAUTIONS:
1. (QVXUHWKDWWKHSDUDPHWHUVRIWKHSURGXFWGHVFULEHGLQLWVVSHFL¿FDWLRQSURYLGHDVDIHW\PDUJLQIRUWKHDSSURSULDWHRSHUDWLRQRIWKHGHYLFHRUV\VWHPDQGQHYHUXVH
the product in circumstances which exceed the parameters of the product. 2. Never touch any live parts of the device. 3. Ensure that the product has been connected
FRUUHFWO\$QLQFRUUHFWFRQQHFWLRQPD\FDXVHPDOIXQFWLRQH[FHVVLYHKHDWLQJRUULVNRI¿UH4. In case of any risk of any serious material loss or death or injuries
of humans or animals, the devices or systems shall be designed so to equip them with double safety system to guarantee their reliable operation.
12
Interconnection strips ZGGZ4
PIR2-...-00L.
(R2N + GZM2)
ZGGZ4
ZGGZ4 for: Plug-in Relays Interface

sockets for plug-in sockets relays ❸
GZM2 R2N PIR2-...-00L. (R2N + GZM2)
GZT2
GZT3
GZT4
❸ Interface relay PIR2 (PIR3, PIR4 LV RႇHUHG DV D set: electromagnetic relay R2N (R3N, R4N) + plug-in
socket GZM2 (GZM3, GZM4 VLJQDOOLQJSURWHFWLQJPRGXOHW\SH M... + retainer / retractor clip GZT4-0040 +
GHVFULSWLRQSODWHGZT4-0035.
Interconnection strip ZGGZ4

• designed for the co-operation with plug-in sockets
of miniature industrial relays and with interface relays
PIR2, PIR3 and PIR4, which are equipped with screw
terminals; sockets and relays are mounted on 35 mm
rail mount acc. to EN 60715,
• bridges common input signals (coil terminals
A1 or A2) or output signals - see photo at the top,
• maximum permissible current is 10 A / 250 V AC,
• possibility of connection of 6 sockets or relays,
23.12.2020
• colours of strips: ZGGZ4-1 grey, ZGGZ4-2 black.
13
Interconnection strips ZGZP...
ZGZP-2 ZGZP4-2 PIR4-...-PS-...

(R4N + GZP4)
ZGZP4-2
ZGZP4-8
ZGZP... for: Plug-in Relays Interface

sockets for plug-in sockets relays ❹
GZP4 R2N PIR2-...-PS-... (R2N + GZP4)
R4N PIR4-...-PS-... (R4N + GZP4)
❹ Interface relay PIR2 (PIR4 LVRႇHUHGDVDset: electromagnetic relay R2N (R4N) + plug-in socket GZP4 +
signalling / protecting module type M... + retainer / retractor clip GZP4-0400.
Interconnection strips ZGZP...

• designed for the co-operation with plug-in sockets of miniature industrial relays
and with interface relays PIR2 and PIR4, which are equipped with screw terminals;
sockets and relays are mounted on 35 mm rail mount acc. to EN 60715,
- strip ZGZP4-8 bridges common input signals (coil terminals A1 or A2),

maximum permissible current is 10 A / 250 V AC, possibility of connection of 8 sockets or relays,
ZGZP4-8 GY grey ZGZP4-8 BK black ZGZP4-8 RD red ZGZP4-8 BE blue
- strip ZGZP4-2 bridges common input signals (coil terminals A1 or A2) or output signals,
possibility of connection of 2+n sockets or relays,
ZGZP4-2 GY grey ZGZP4-2 BK black ZGZP4-2 RD red ZGZP4-2 BE blue
- jumper ZGZP-2 bridges the neighboring poles of single socket GZP4.

23.12.2020
ZGZP-2 GY grey ZGZP-2 BK black ZGZP-2 RD red ZGZP-2 BE blue
14

Miniature Industrial Relays: Contact Data

Uploaded by

Copyright:

Available Formats

Miniature Industrial Relays: Contact Data

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Miniature Industrial Relays: Contact Data

Uploaded by

Copyright:

Available Formats

R2N

miniature industrial relays

Design Dimensions - plug-in version (WT),

6,3 6,3 4,14,2

Improvement of the functionality of the mechanical

6,3 6,3 4,14,2

Application of electronics made in the SMD techno-

Connection diagram (pin side view)

tion of the relay.

Mounting, sockets and accessories for relays

DC voltage [V] Ambient temperature [°C]

Coil operating range - AC 50 Hz Fig. 5 Description of Fig. 4 and 5

contacts. Make voltage is not higher than the value read on Y

Ambient temperature [°C]

• AgNi - for resistive or inductive loads,

Coil data - DC voltage version Table 1

Coil resistance Coil operating range

Coil data - AC 50/60 Hz voltage version Table 2

Coil resistance Coil operating range

Relays for railroad industry

Type Contact Number and type Connection Coil code Additional

Number and type of contacts

Cover protection category

3 - for plug-in sockets

Example of ordering codes:

Type ❶ Description For industrial relays

T lockable front test button, R2N, R3N, R4N,

L light indicator (LED diode), R2N, R3N, R4N, RY2,

D surge suppression element (diode) R2N, R3N, R4N, RY2,

V surge suppression element (varistor) (R15 - 2 CO, 3 CO ❷)

K test button without block function, (R15 - 4 CO ❷),

Test buttons type T R2N, R3N, R4N

Button R4P-0001 or R15-M404 can be easily inserted by the Customer after

Dimensions - test button R4P-0001 Dimensions - test button R15-M404

Types of buttons: Types of buttons:

Dimensions - plug R4W-0003 Dimensions - plug R15-M203

Types of plugs: Types of plugs:

GZT2 Connection diagram Dimensions

Accessories ❶ GZT4-0035 Module type M...

GZM2 Connection diagram Dimensions

Accessories ❶ GZT4-0035 Module type M...

Mounting and sub-assemblies of the relay and accessories in the socket

Signalling / protecting module Electromagnetic

Retainer / retractor clip

Removing the relay from the socket

GZP4 Connection diagrams Dimensions

2 x 1 mm2 (ferrules with insulation)

The drawings present

GZP4-0400 GZT4-0040 G4 1052 MP15 ZGZP4-2 ZGZP-2 Module type M...

Accessories ❶ Wire connection

SU4/2D Pinout Dimensions

SU4/2L Dimensions of opening on panel mounting Dimensions

Accessories G4 1053 G4 1040

G4/2 Pinout of openings on panel mounting Dimensions

For sockets type:

Modules type M... are parallely connected with relay coil.

Modules type M... Layout Voltage Type of module ❶ ❷

Module D (polarization N) 6/230 V DC M21N

Module LD (polarization P) 6/24 V DC M31R, M31G