Beast ATV Deluxe

User Manual
About Daymak
Daymak is one of Canada’s largest Alternative Vehicle providers. We design, engineer,
manufacture, import and repair everything from recreational dirt bikes, go-karts and
electric golf cars to alternative transportation solutions such as e-bikes and gas scooters.

Our electric bicycles represent an energy-e-fficient and eco-friendly alternative for peo-
ple who need to get around the city. They greatly increase the practicality of bicycle
transportation in urban centers. Costing only a few cents to charge, an e-bike can make
city life more convenient and much less expensive. While there are many new Green
technologies that are still in their infancy, electric bicycles have been developing over the
last 40 years or more. E-bike technology has been dramatically re invented since the in-
troduction of the 1st custom-conversion bicycles. Today, electric bicycles are a supreme-
ly reliable and affordable means of transportation. Daymak is constantly developing new
eco-friendly alternative transportation strategies, led by its own Research and Develop-
ment department in Toronto, Canada.

We are always improving our products. Our innovative in-house engineering and qual-
ity testing provide customers with many new kinds of reliable, eco-friendly vehicles,
designed to help change the lives of our customers and the world. Daymak warranties,
services, and stocks parts for everything it sells. We support our products. Please feel free
to visit our website. You’ll find the latest in cool transportation solutions, support for the
products you’ve purchased and contact information.
Components
1) Trunk
2) Seat
3) Throttle
4) Display
5) Headlights
6) Winch
7) Plow
8) Tire
9) Gas Shocks
10) Bluetooth Controller
11) Charging Port
12) Motor Switch
13) Tail Light

3
Safety
When operating the Beast ATV Deluxe please make sure you adhere to the following:

Always where a helmet when riding the Beast ATV Deluxe

Always check your mirrors and blind spots when operating through trails.

Turn on headlights when in need of additional visibility.

Make sure that your battery power is sufficient before you go out to ride

Do not ride with more than 1 passenger

Do not over charge the battery by leaving the charger in the charging port. Once the
battery is fully charged remove the charger immediately.

Do not try to operate the unit while charging.

Do not let anyone uner the age of 16 years old operate this vehicle.

Do not operate this unit up extreme inclines to avoid tipping.

Do not make sharp / abrupt turns at high speeds to avoid tipping.

Do not operate under the influence of any use of drugs or alcohol

Do not operate on public roads

Do not operate at excessive speeds.

Do not completely submerge the unit in water

4
Operation
Powering on the unit

When you are ready to use your Beast ATV, start

by turning the ignition, located on top of the front
right wheel well (seen here) clockwise. It comes
with two sets of keys so be sure to keep the spare
separate for safe keeping. Once you are finished
turn the ignition counterclockwise to turn off the
unit.

Once the key is on be careful not to accidentally

twist the throttle until you are ready to ride. We
recommend putting on the brake lock when you
are finished with the unit and releasing it as the
last step before you begin to ride.

5
 Connecting to your unit via Bluetooth

The Beast ATV can be connected to via bluetooth to increase torque range and more.

Once the App is open, it will show you a list of the nearby bluetooth devices as well as the Front
and rear motor. Connect to the rear motor or front (whatever is your preference). For the first time
you connect, it will require you to input a password: 12345678.

Once you have done that, a speedometer will show up and you are ready to go!

For more information on the Daymak Drive App, please refer to the quick guide seen here:

http://daymak.com/manuals/Daymak%20Drive%20Manual.pdf

Please note the Beast ATV has two controllers, so any chang-
es to effect one motor, will not effect the other.

6
Riding the Unit
Motor Controls
The Beast ATV has two motor switches on
each side of the unit.

The switch that is on the right side of the

unit (as if you were sitting on it) controls the
front motor.

The switch that is on the left side of the unit

(as if you were sitting on it) controls the
rear motor.

To turn each motor on, flip the switch so the

LED light, is showing (pressed in towards
the front of the ATV). If both switches are
turned on you will have all wheel drive.

Throttle

Once you have chosen which motors you want to en-

gage, rotate the throttle (the right handle seen above)
towards you to go. Do this slowly to get your bearings
and once you are comfortable continue rotating until
you reach your desired speed.

7
Brakes
On both sides of the handlebar there are brake levers
as seen on the right. To engage the brakes, pull the
brake lever towards you.

The right brake lever activates the front brakes

The left brake lever activates the rear brakes

Brake lock / Wheel Lock

To engage the brake lock, first pull the
brake lever towards you as you would nor-
mally engage the brakes.

Then push the knob seen here behind the

brake lever . To release it pull the small
latch that surrounds the button back and
pull the brake lever again to its normal po-
sition

8
Features
On the left handlebar you have the following
functions

1) Lights
There are three positions that this can slide
into. The lowest position has the lights off.
The middle position has the lights on with
low beams, and the the highest position has
the lights on with high beams.

2) Turn Signals
Push this switch to the left to indicate going
to the left and right to indicate going to the
right. Once done making the turn set the
switch into the middle position and then
push it in,

3) Horn
Press this button to honk the Horn

4) Forward and Reverse

Push this button in to go in reverse. Push
this button a second time to release it and
go forward.

*Please note the unit must make a com-

plete stop before switching directions*

5) Heated hand grips

This switch heats the handgrips. Set this to
1 to turn the hand grips on low. Set this to 2
to turn the hand grips on high and set this
to 0 to turn it off.

9
 Display
The display on the Beast ATV deluxe will
show your speed as well as your odome-
ter and trip meter.

There are two buttons on the display.

Left Button - Toggles between Odometer

and Trip Meter

Right Button - Turns on LED back light to

either Blue, Orange, or Off.

Ball Joint
The display on the Beast ATV deluxe also
comes with a ball joint that allows you to
tow up to 2000 lbs behind the unit.

Trunk
The Beast ATV deluxe also comes with a
trunk that adds extra storage. Simply lift
the two latches to unlock it and open it.

This trunk connects to your brake light

and shines when you brake.

10
Winch (Optional)
The Beast ATV comes with a winch that allows you to tow things, or in case you have the plow add
on, it allows you to raise and lower the snow plow.

On the right handlebar of the unit you will see a red

switch with three positions on it.

Push the triangle pointing forward to release ten-

sion from the winch to allow for more cable to be
released

Push the middle circle to be neutral

Push the triangle pointing backward to pull in the

cable and create tension.

11
Maintenance
Charging the Unit

On the side of the Beast ATV, you will find a charging port
as seen on the right. This cover can be slid either direc-
tion to reveal the charging port. Plug the charger into this
slot.

The charger light will glow orange while it is charging.

Once it is finished charging the charger will turn green.
Unplug the charger as soon as possible once complete
and you are ready to ride.

Please do not over charge the battery as it may lead to a

lower lifespan and possible damage to the ATV, including
fire or even explosion

12
Service
It is recommended that you bring your unit for service at least once a year to have it checked up to
make sure it is functioning as intended.

• Check to make sure the brakes are working properly

• Ensure all bolts are secure
• Check the life of the output of the battery pack
• Make sure tires are sufficiently pumped.
• Ensure all electronical connections are secure

It is recommended that it is brought into an authorized Daymak dealer, however a local mechanic
shop that has experience with ATVs may be able to offer the same service.

Troubleshooting

If you have issues with your Beast ATV, try these steps before considering bringing it in for service.

1) Check to make batteries are fully charged.

2) Make sure the key is in the ignition and set to on

3) Make sure to release the brake lock once properly situated on the unit.

4) Check to make sure at least one of the motor switches is set to the on position.

5) If you are having problems connecting to your smartphone, make sure that the Bluetooth feature is
set to on and that the battery on the tablet is charged.

6) If the charger light doesn’t turn red when plugged into the port, make sure that it is pushed com-
pletely in.

13
Specifications

Battery: 60V 50AH Battery Pack

Front Motor: 1000W
Rear Motor: 1000W
Controller: 2 x Daymak Drive Turbo Bluetooth Controllers
Tire Size Front: 23 x 7-10
Tire Size Rear: 22 x 10 - 10
Battery Life Cylces: 300 Cycles
Range: Up to 80 km
Off Road Speed: Up to 50 km/hr
Reverse Switch: Yes
Charger: 60V2.5Ah
Charging Time: 8 - 10
Degrees of Incline: 25 Degrees
Dimensions: 71 “ x 49” x 53”
Weight: 120 kg
Max load: 350 lbs
Brakes: Disc Brakes
Suspension: Gas Dual Front / Gas Single Rear
Seat Height: 36"

14
Warranty info
Your warranty for your Ultra Beast covers the frame and motor for 2 years, and parts as stipulated
by your dealer.

Your Warranty Does Not Cover:

- Any damage resulting from negligence of the periodic maintenance.
- Any damage which results from repair, adjustment or maintenance operations by any methods oth-
er than those specified by Daymak Inc.
- Any damage which results from driving due to race, rally, or operation of the vehicle in a location
that is not used for normal operational driving of such a vehicle.
- Any damage which results from use beyond the limitations specified in the Daymak Inc. Operations
Manual such as overloading the vehicle, or any damage from the use under abnormal conditions
(abuse of vehicle).
- Any damage caused when the product is used as a rental vehicle.
- Any damage which results from use of non-genuine parts or accessories (aftermarket/other deal-
er’s add-on/replacement parts).
- Any damage due to improper storage or transport of vehicle or batteries.
- Any damage which may results from repair, adjustment or maintenance operations performed by
any person other than Daymak distributor (or the Daymak authorized Dealer).
- Any damage which results from modifications of the product.
- Any damage that results from the passage of time (natural fading of painted surfaces, plated sur-
faces, sheet peeling, and other deterioration).
- Regular wear and tear items. Daymak will not warranty parts worn due to natural wear and tear
(including, but not limited to, light bulbs, tubes, tires, worn brakes, cables, fuses, etc.).
- Any damage which results from unavoidable disasters (natural or otherwise) and/or secondary
damages based on any of these occurrences (fire, flood, wind damage, snow, collision, theft, etc.).
- Incidental or additional expenses incurred for making the warranty repair at the location of pur-
chase, such as towing, pick up and deliveries, as well as any losses during maintenance period,
such as loss of time, loss of business and/or rental car expenses.
- Scheduled maintenance and inspections fees.

15
 Thank you for choosing Daymak

16