2 Product Introduction

2.15 Introduction to the AN5506-04-FA

2.15.1 Appearance

The following describes the appearance of the AN5506-04-FA, including the overall
look, interfaces, buttons, and indicator LEDs.

Note:

The pictures here are only for reference.

Appearance

The overall look of the AN5506-04-FA is shown in Figure 2-33.

Figure 2-33 Overall Look of the AN5506-04-FA

Interface and Button

Interfaces and buttons of the AN5506-04-FA are located on the rear and back
panels of the equipment. Figure 2-34 shows the rear panel and Figure 2-35 shows
the back panel.

Version: A/1 101

AN5506-01/AN5506-02/AN5506-04 Series GPON Optical Network Terminal Product Manual

Figure 2-34 Rear Panel of the AN5506-04-FA

Figure 2-35 Back Panel of the AN5506-04-FA

Table 2-52 describes the interfaces and buttons of the AN5506-04-FA.

Table 2-52 Interfaces and Buttons of the AN5506-04-FA

Interface and
Description Function
Button
2.4G WPS/5G WPS
WPS1/WPS2 The 2.4G/5G WLAN data encryption switch
function button
2.4G/5G WLAN
WLAN1/WLAN2 Enables / disables the WLAN function.
function button

102 Version: A/1

 2 Product Introduction

Table 2-52 Interfaces and Buttons of the AN5506-04-FA (Continued)

Interface and
Description Function
Button
Phone1, Phone2 Telephone interface Connects to the user's telephone.

Connects with the computer, IP router or IP set

LAN1 to LAN4 Ethernet interface
top box.

USB1, USB2 USB Host interface Connects to the USB interface storage device.

ON/OFF Power switch Turns on or off the power for the equipment.

Power Power interface Connects with the power adapter.

Pressing down the button for no more than 5

seconds to reboot the equipment; pressing
Reset Reboot button down the button for more than 5 seconds to
restore the factory settings and reboot the
equipment.

PON Fiber interface Connects with optical fiber for uplink access.

Indicator LED Description

Indicator LEDs of the AN5506-04-FA are located on the front panel of the equipment.
Table 2-53 describes the indicator LEDs.

Table 2-53 Indicator LEDs on the AN5506-04-FA

Indicator LEDs Meaning Color Status Status Description

Power status ON The equipment is powered on.

Power Green
indicator LED OFF The equipment is not powered on.

ON The ONT is activated.

Register status
PON Green Blinking The ONT is being activated.
indicator LED
OFF Activation of the ONT is not yet started.

Optical signal The equipment has not received the optical

Blinking
LOS status indicator Red signal.
LED OFF The equipment has received the optical signal.

USB indicator ON The USB is connected.

USB1, USB2 Green
LED OFF The USB is not connected.
The interface is connected to the user terminal
ON
Ethernet interface and no data is transmitted.
LAN1 to LAN4 status indicator Green Blinking The interface is transmitting / receiving data.
LED The interface is not connected to the user
OFF
terminal.

Version: A/1 103

AN5506-01/AN5506-02/AN5506-04 Series GPON Optical Network Terminal Product Manual

Table 2-53 Indicator LEDs on the AN5506-04-FA (Continued)

Indicator LEDs Meaning Color Status Status Description

The equipment is registered in the softswitch

Voice service ON
system.
VOIP register status Green
The equipment is not registered in the
indicator LED OFF
softswitch system.

ON The port is registered in the softswitch system.

Phone1, Phone port status Blinking Service flow is found at the port.
Green
Phone2 indicator LED The port is not registered in the softswitch
OFF
system.

ON The 2.4G/5G wireless interface is enabled.

2.4G/5G wireless
The 2.4G/5G wireless interface is transmitting /
WIFI1/WIFI2 signal status Green Blinking
receiving data.
indicator LED
OFF The 2.4G/5G wireless interface is disabled.
The 2.4G/5G WPS is enabled, and the Wi-Fi
ON
2.4G/5G WPS terminal has been connected to the ONT.
WPS1/WPS2 status indicator Green Blinking The 2.4G/5G WPS is being used in negotiation.
LED The 2.4G/5G WPS is not enabled, or the Wi-Fi
OFF
terminal is not connected to the ONT.

2.15.2 Product Characteristics

The AN5506-04-FA can be used together with the OLT equipment to make up a
GPON system and access multiple services for users. The AN5506-04-FA has the
following characteristics:

1. GPON access capability

u Conforms to ITU-T G.984 series of standards, with good interoperability.

u Provides large-capacity GPON transmission bandwidth: supports 2.5 Gbit/s for

the downlink rate and 1.25 Gbit/s for the uplink rate.

u Supports the DBA (Dynamic Bandwidth Allocation) algorithm.

u Supports long-haul transmission. The maximum transmission distance can

reach 20 km.

104 Version: A/1

 2 Product Introduction

2. Abundant service types

The equipment provides abundant physical interfaces on the subscriber side to

access multiple services such as Internet access, video, voice and home storage
services.

3. Wi-Fi wireless access

u The equipment provides Wi-Fi wireless access based on IEEE 802.11

a/b/g/n/ac to set up safe and reliable wireless network for users.

u Compatible with IEEE 802.11 a/b/g/n/ac and passed Wi-Fi Alliance

authentication, with good compatibility with other WLAN devices.

u Supports eight SSIDs (four SSIDs for the 2.4 GHz band and another four
SSIDs for the 5 GHz band) so that users can set different wireless networks as
needed.

u Supports multiple authentication and encryption modes to provide users with

safe and reliable wireless access mode.

4. Network storage and file sharing

u Provides two USB interfaces for connection with the USB interface storage
devices to provide convenient network storage and file sharing service.

u The USB interfaces support plug-and-play and hot insertion.

u Supports configuration of the USB function based on the Web page to facilitate
file sharing in the family network.

u Supports the FTP-based network storage to provide FTP client end and FTP
server end functions. Users can download the files on the public network FTP
server to the USB interface storage devices or visit the USB interface storage
devices on the ONT via the FTP client end on the PC.

5. Gateway functions

u Serves as home gateway and provides abundant and reliable gateway

functions.

u Functions as the DHCP Server to cater for application demands in different

scenarios.

Version: A/1 105

AN5506-01/AN5506-02/AN5506-04 Series GPON Optical Network Terminal Product Manual

u Supports configuring protection against DoS attack, filtering of MAC addresses,

IP addresses and URL addresses, firewall and ACL rules to guarantee safe
operation of the equipment.

6. Remote automatic provisioning of services, maintenance and management

u The equipment adopts the management based on TR-069 and OMCI, and
supports TR-069 over OMCI. It can manage terminal services without IP
network, which facilitates automatic provisioning, maintenance and
management of services remotely.

u Supports configuring the global profile and delivering the XML configuration file
on the network management system. Only a few changes are required to
deliver the ONT services in a batch manner and make network adjustment.

u Supports configuring the user-defined upgrade policies on the network

management system so that the equipment can be upgraded automatically
after being powered on.

u Supports collecting performance data of the ONT remotely via the network
management system to enable real-time monitoring of the network
performance.

u Supports remote fault isolation for the ONT via the network management
system. Faults can be isolated remotely according to the alarms reported to
reduce the maintenance cost.

2.15.3 Functions and Features

Table 2-54 lists the functions and features of the AN5506-04-FA.

Table 2-54 Functions and Features of the AN5506-04-FA

Item Description

Compliant with standards ITU-T G.984.1, G.984.2, G.984.3 and G.984.4.

Supports GEM encapsulation (Ethernet over GEM is supported, but ATM

GPON encapsulation is not supported).
GPON interface The GPON system adopts the single-fiber bidirectional transmission mechanism,
specifications using the TDMA mode with the wavelength 1310 nm in the uplink direction, and the
broadcast mode with the wavelength 1490 nm in the downlink direction.

Supports the embedded OAM message, PLOAM message and OMCI message.

106 Version: A/1

 2 Product Introduction

Table 2-54 Functions and Features of the AN5506-04-FA (Continued)

Item Description

Supports the splicing of data packets and OMCI protocol packets in the uplink
direction. Splicing with adaptive message length and that with fixed length are
supported.

Supports bearing the downlink broadcast packets and unknown multicast packets via
the broadcast GEM port.

GEM Port Supports mapping from GEM ports to T-CONTs.

Supports multiple flow mapping modes.

Supports the GEM port loopback.

Supports T-CONTs of Type 1 to Type 5.

T-CONT A T-CONT supports no less than 64 GEM ports.

Supports eight T-CONTs.

Supports DBA in the SR and NSR modes.

DBA
Supports DBA Piggy-back DBRu Mode 0.

Supports bi-directional FEC: downlink FEC decoding and uplink FEC encoding.
FEC
Supports downlink FEC performance statistics.

Supports encryption of downlink unicast data channel.

Supports the AES-128 encryption algorithm.

Encryption
Supports generation of the key and response to the OLT's request for key.

Supports OMCI channel encryption.

Supports the ONT registration process as specified in ITU-T. G.984.3.

Registration Supports four authentication modes: SN, Password, SN＋Password and LOID.
authentication Supports performance statistics for the Ethernet interface.

Supports performance statistics for the GEM interface.

Complies with the IEEE 802.3 standard.

Supports configuring the Ethernet interface rate, working mode, and MDI/MDIX auto-
negotiation mode.

Supports manual configuration to the rate 10/100/1000 Mbit/s.

Supports manual configuration of the half duplex or full duplex mode.

Ethernet
Supports unlink / downlink rate control based on the Ethernet interface, with the
control granularity of 64 kbit/s.

Supports the PAUSE flow control.

Supports the loopback detection at the subscriber side.

Supports learning up to 1024 MAC addresses.

Version: A/1 107

AN5506-01/AN5506-02/AN5506-04 Series GPON Optical Network Terminal Product Manual

Table 2-54 Functions and Features of the AN5506-04-FA (Continued)

Item Description

Supports global configuration of enabling / disabling the MAC address learning

function.
Supports remote configuration of the MAC address aging time. The value ranges
between 0s and 300s. The default value is 80s.
Supports the IGMP Snooping protocol.

Supports IGMP v1/v2/v3.

Supports filtering and forwarding of multicast MAC addresses.

Supports controllable multicast and uncontrollable multicast.

Supports fast leave.

Supports translation, transparent transmission and stripping of the multicast VLAN

tags.

Supports VLAN translation for the uplink multicast protocol packets.

Multicast Supports filtering the downlink multicast packets.

Supports bearing downlink multicast service flow and IGMP signaling packets via
different GEM ports.

Supports configuration of the multicast GEM ports.

Supports authentication of the GEM ports.

Supports no less than 256 multicast groups.

Uses the IPoE/PPPoE mode for the multicast services.

Supports the IPv6 Snooping multicast service, supports the MLDv1 information,
MLDv2 query information and MLDv2 report information.

Supports the IEEE 802.1Q VLAN standard.

VLAN Supports joining the 802.1Q VLAN in the tag / untag mode.

Supports up to 4095 VLANs.

Wire-speed forwarding Supports Layer 2 / Layer 3 wire-speed forwarding.

Supports the IPv4/v6 dual stack.

Supports obtaining network parameters such as the user IP address, subnet mask
and DNS in the DHCP mode. Supports reporting the physical location of the Ethernet
interface based on DHCP Option82.

Layer 3 features Supports obtaining user IP addresses in the PPPoE mode, and supports the PPPoE+
function for precise identification of users.

Supports static routing and default routing.

Supports DDNS, NAT, port forwarding and DMZ.

Supports ARP, UPnP, ALG, Portal and QoS.

Voice Supports the protocols H.248 and SIP.

108 Version: A/1

 2 Product Introduction

Table 2-54 Functions and Features of the AN5506-04-FA (Continued)

Item Description

Supports the speech encoding modes such as G.711, G.729, G.723.1 and G.722.

Provides a phone number for each connected telephone set.

Supports simultaneous call and conversation of two POTS subscribers.

Supports static and dynamic jitter buffer.

Supports DTMF detection.

Supports RFC 2833 for transmitting / receiving DTMF.

Supports RTP/RTCP (RFC 3550).

Supports 802.11b, 802.11g, 802.11n, 802.11b/g and hybrid mode for the 2.4 GHz
frequency band; supports 802.11a, 802.11n, 802.11ac and hybrid mode for the 5 GHz
frequency band.

Supports the MIMO program for the 2.4 GHz and 5 GHz frequency bands.

Supports eight SSIDs (four SSIDs for the 2.4 GHz band and another four SSIDs for
the 5 GHz band) to differentiate networks.

Supports 13 working channels in the 2.4 GHz frequency band and 20 working
channels in the 5 GHz frequency band.
WLAN
Supports automatic selection and manual configuration of channels.

Supports Open System, Shared key, WPA, WPA2, WPA-PSK, WPA2-PSK and WPS
authentication.
Supports the WEP, TKIP, AES and AES/TKIP encryption.

Supports the WPS negotiation encryption algorithm and key.

Supports adjustment of the transmit power, which is configured in form of percentage.

Ten options are provided: 20%, 40%, 60%, 80%, 100%, 120%, 140%, 160%, 180%
and 200%. Other values are not supported.

Complaint with the USB 1.1/USB 2.0 standard.

Supports plug-and-play and hot insertion of the USB storage device.

USB
Supports storage devices such as the USB HUB and mass storage.

Supports providing the FTP service on the USB.

Supports the firewall.

Supports packet filtering.

Supports filtering MAC addresses.

Supports filtering URL addresses.

Security
Supports protection against illegal message (DoS, ARP) attacks; supports
suppression of broadcast storms.

Supports configuring the HTTPS safe channel.

Supports configuring ACL rules for the ONT.

Version: A/1 109

AN5506-01/AN5506-02/AN5506-04 Series GPON Optical Network Terminal Product Manual

Table 2-54 Functions and Features of the AN5506-04-FA (Continued)

Item Description

Supports remote control.

Supports local service configuration, query and software upgrade based on the Web
page.

Supports management of the OMCI configuration and queries.

Supports delivering the XML configuration file via the OMCI, alarm reporting, alarm
Management and
synchronization and performance statistics.
maintenance
Supports automatic provisioning of services, equipment management and software
upgrade remotely based on OMCI/TR-069.

Supports query of the ONT optical module information.

Supports TYPE B protection.

Provides abundant QoS functions; supports global configuration of queue priorities

and flexible mapping of 802.1p values in packets.

Supports the ACL function to match traffic based on the ACL rules.
QoS
Supports three queue scheduling modes (PQ, WRR and PQ+WRR); supports
configuring the weight of the queues under scheduling, so as to guarantee the quality
of high-QoS services such as voice and video in the multi-service scenario.

2.15.4 Technical Specifications

See Table 2-55 for the technical specifications of the AN5506-04-FA.

Table 2-55 Technical Specifications of the AN5506-04-FA

Classification Item Description

Dimensions 37mm × 252mm × 178mm (H × W × D)

Mechanical Wall mounting hole
190mm
parameters distance
Weight About 570g

Power supply
DC DC 12 V/2.5A
parameter

Static power consumption 10W

Power consumption
Maximum power
parameters 15W
consumption

Operating temperature -5℃ to 45℃

Environment
Storage temperature -40℃ to 70℃
parameters
Environmental humidity 5% to 95% (no condensation)

110 Version: A/1