Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 4 views

    QI-552V DSI Interface Unit

    Uploaded by

    hieu.ttlmeditech

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    QI-552V DSI Interface Unit

    Uploaded by

    hieu.ttlmeditech
    4 views2 pages

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    4 views2 pages

    QI-552V DSI Interface Unit

    Uploaded by

    hieu.ttlmeditech

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    You are on page 1of 2

    INSTALLATION GUIDE

    0604-021306 DSI Interface Unit QI-552V


    DSI/AUXOUT Interface Unit QI-553V
    First Edition: 30 Aug 2004 for TEC-5521, TEC-5531 Series Defibrillator
    12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121
    12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121
    12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121

    The CE mark is a protected conformity mark Installation Procedure


    of the European Community. The products
    herewith comply with the requirements of 1. Make sure that the power of the defibrillator is turned off.
    Medical Device Directive 93/42/EEC. 2. Disconnect the AC power cord from the AC outlet and
    defibrillator.
    General 3. Remove the battery pack if it is installed.
    The QI-552V DSI Interface Unit and QI-553V DSI /AUXOUT
    1) Turn the knob on the battery holder cover
    Interface Unit are designed to measure CO2 and SpO2
    waveforms for the TEC-5521, TEC-5531 Series Defibrillator counterclockwise and remove the battery pack holder
    (The optional TG-901T3 or TG-921T3 CO2 Sensor Kit, JL- cover.
    951T3 SpO2 Adaptor and sensor are necessary). The DSI/
    AUXOUT interface unit outputs ECG waveforms. This
    installation guide explains how to install the DSI interface unit
    and DSI/AUXOUT interface unit into the defibrillator. For
    installation, refer to the TEC-5500 Service manual. For safety
    and use, read the TEC-5500 operator’s manual.

    Model SpO2/CO2 AUX 2) Disconnect the battery cable by holding the battery
    connectors connector cable connector and remove the battery from the
    DSI Interface Unit 2* 0 defibrillator.
    DSI/AUX OUT Interface Unit 1 1
    4. Remove the DSI blank panel.
    * The same parameter cannot be measured on two connectors.
    1) Turn the defibrillator over.
    2) Remove the two M3×2 binding head screws. These
    WARNING screws are used when the interface unit is attached.
    • Installation must be done by qualified service M3×2 binding head screw
    personel.
    • To avoid the possibility of injury to yourself or
    damage to the defibrillator, do not install or remove
    any component or change switch settings while the
    power is on. When disassembling, make sure that the
    defibrillator is off, the AC power cord is disconnected
    from the defibrillator, and the battery pack is
    removed from the defibrillator.

    3) Remove the DSI blank panel by pulling it toward you.


    Compositions
    DSI blank panel
    Description Q'ty
    DSI interface unit
    1
    Or DSI/AUXOUT interface unit
    Revision label 1

    Installation Guide QI-552V/QI-553V 1


    5. Attach the interface unit.
    1) Connect the defibrillator and interface unit with the
    cable.
    Interface unit

    3. Select “5. DSI Option” with the Item key.


    4. Select “On” with the ← or → key.
    5 Select “11. Flash Save” with the Item key.
    6. Press the ← key. The setting changes from “Off” to “Exec”
    2) Attach the interface unit to the defibrillator and secure and the function key changes as follows:
    it with the two M3×2 binding head screws.

    6. Install the battery pack. 7. Press the OK key.

    Enabling the Interface Unit Operation Check


    1. Open up the System Maintenance Screen For the defibrillator operation, refer to the TEC-5500 operator’s
    1) Connect the AC power cord manual.
    2) While pressing and holding the 1. Connect the AC power cord to the defibrillator and connect
    Silence alarms key, turn the Energy/ the other end of the AC power cord to the AC outlet.
    Mode Select control to the “SETUP” 2. Turn on the power of the defibrillator.
    position. The System Setup - Menu 3. Check that no error message is displayed.
    screen appears. 4. Connect the TG-901T3 or TG-921T CO2 Sensor Kit, or JL-
    3) Release the Silence alarms key. 951T3 SpO2 Adaptor to the connector on the DSI Interface
    4) While pressing the Multi-function Unit.
    5. Check that “CO2” or “SpO2” is displayed on the screen
    key, press the following keys on the (the waveforms and measurement data are displayed in
    front panel one by one: dotted lines).
    ECG lead key → Silence alarms key For the CO2 and SpO2 measurement, refer to the Operator’s
    → ECG sensitivity key. manual of the TG-901T3/TG-921T CO2 Sensor Kit and JL-
    951T3 SpO2 Adaptor. For the ECG analog signal output,
    refer to the TEC-5500 operator’s manual.
    If “CO2” or “SpO2” is not displayed, check that the
    The System Maintenance - Menu interface unit is correctly installed. Refer to “Installation
    screen appears. Procedure”.
    5) Release the Multi-function key. 6. Turn off the power of the defibrillator.

    2. Select “Configuration” with the Item key and press the OK Attaching the Revision Label
    key to open the System Maintenance - Configuration. After checking operation, attach the revision label to the rear
    panel.

    QI-55XV
    00001 AA

    Clean where the label IPX1


    QI-55XV
    00001 AA

    will be attached with


    cotton moistened with
    alcohol.

    2 Installation Guide QI-552V/QI-553V

    You might also like