LAT-SERIES BOLTING PUMP

REPAIR PARTS SHEET

MODEL LA2504TX-QR

L4403 REV. D 10/21

FOR PRODUCT DATE CODES BEGINNING WITH THE LETTER “A”

NOTE: To protect your warranty, use only ENERPAC hydraulic oil.

Enerpac recommends that all kit components be installed to ensure
optimum performance of the repaired product.
TABLE OF CONTENTS
PAGE
FIGURE 1: MAIN ASSEMBLY................................................................................................................................ 3
FIGURE 2: FILTER/REGULATOR, AIR LUBRICATOR AND PENDANT ASSEMBLY........................................... 4
FIGURE 3: FILTER/REGULATOR/AIR LUBRICATOR GROUP............................................................................. 5
FIGURE 4: AIR PENDANT ASSEMBLY................................................................................................................. 6
FIGURE 5: COVERPLATE COMPONENTS........................................................................................................... 7
FIGURE 6: HYDRAULIC RESERVOIR................................................................................................................... 8
FIGURE 7: CONTROL VALVE (UNDERSIDE VIEW)............................................................................................ 10
FIGURE 8: CONTROL VALVE (TOP VIEW).......................................................................................................... 11
FIGURE 9: CONTROL VALVE (B-SIDE RELIEF ASSEMBLY)............................................................................. 12
FIGURE 10: PUMP ASSEMBLY (UNDERSIDE VIEW)........................................................................................ 14
FIGURE 11: PUMP ASSEMBLY (TOP VIEW - DISASSEMBLED)....................................................................... 16
FIGURE 12: AIR MOTOR ASSEMBLY AND FITTINGS (EARLY MODELS)........................................................ 17
FIGURE 13: AIR MOTOR ASSEMBLY AND FITTINGS (LATER MODELS)........................................................ 18
FIGURE 14: AIR LOGIC & SCHEMATIC DIAGRAM............................................................................................ 19

WARNING Shut off compressed air supply, disconnect air supply line and be sure all hydraulic pressure is
completely relieved before performing any disassembly or repair procedures. Verify that hydraulic pressure gauge
indicates zero (0) psi/bar.

2 L4403 (rev. d)
 Figure 1: Main Assembly

See Fig. 6

2
See Fig. 4

See Fig. 2 & 3

See Fig. 2

See Fig. 5

1
See Fig. 5, 7, 8 & 9 See Fig. 10-14

See Fig. 6
4

Repair Parts List for Figure 1

Item Part Number Qty. Description Item Part Number Qty. Description
1 (See Fig. 5 & 7-9) 1 Manifold Assembly 4 (See Fig. 6) 1 Reservoir Assembly
2 (See Fig. 2 & 3) 1 Air Logic Group 5  DD7816500 1 Weldment, Roll Cage LAT
3 (See Fig. 10-14) 1 Pump Assy, Basic
 Item included in Roll Cage Service Repair Kit DD7816500SR.

L4403 (rev. d) 3
 Figure 2: Filter/Regulator, Air Lubricator and Pendant Assembly

4
1 3 5
13 4 6
12 7

5
15 2 4

10 2

GREEN

RED
9 2 4

BLACK
NOTES:

1 TORQUE TO 45-50 lb-in [5.1-5.6 Nm]. 3 1

2 TORQUE TO 15-18 lb-in [2.0-2.4 Nm]. 11

3 APPLY LOCTITE 243.
4 APPLY PTFE TAPE. LEAVE 1-2 LEAD THREADS EXPOSED.
5 TORQUE TO 20-25 lb-in [2.3-2.8 Nm].
8
6 TIGHTEN HAND TIGHT PLUS 1-2 ADDITIONAL TURNS.

7 TIGHTEN HAND TIGHT PLUS 2 ADDITIONAL TURNS

TO A LEAK FREE CONDITION.
8 TORQUE LOCKNUT TO 42-46 lb-in [4.7-5.8 Nm].

GREEN
Connect to item 16
of Figure 8.

RED

14 2

8
BLACK 7

6
GREEN

4 L4403 (rev. d)
 Repair Parts List for Figure 2
Item Part Number Qty. 2
Description Item Part Number Qty. Description
1  CBA615028-1E 2 Screw, BHCS Hex 9 DD7847095 1 Elbow, 3/8” NPTF
2 DC3574097 1 Y Fem to Fem Conn 10 DD7848660 1 Valve, Air Control
3 DC8170097 3 Elbow, Swivel 3 11 (See Fig. 4) 1 Assembly, Air Pendant
4 4 (See Fig. 3) 1 Air Filter Reg. Group 12 DD7996097 1 Elbow, 90 Deg Union
5 DD7760268 2 Tube, 1/2" OD x 2.25" Lg 13 DD8179431 1 Nipple - Swage
6 DD7842268 1 Air Tube, GRN, Short 14 E112041097 1 Coupling, Air 5/32 Nylon
7 DD7843268 1 Air Tube, GRN, Long 15 F100097-104 1 Connector, Male 3/8 - 1/2"
8 DD7844268 1 Air Tube, BLK
 Included in Filter Regulator Lubricator Kit, LATRFLK.
Body connector must be
rotated 180 ̊ as shown.

Figure 3: Filter/Regulator/Air Lubricator Group

1
2
3

NOTES:

1 ADJUST LUBRICATOR TO FEED 1 DROP OF OIL

FOR EVERY 50 SCFM [1415 L/M] OF AIR WHILE
THE UNIT IS RUNNING, OR 1 DROP OF OIL PER
1 CONTINUOUS MINUTE OF RUN TIME. DO NOT
OVERFEED OIL OR EXHAUST AIR MAY BE
CONTAMINATED.

2 FILL THE LUBRICATOR RESERVOIR TO THE PROPER

LEVEL WITH SAE10W HIGH DETERGENT OR
NON-DETERGENT MOTOR OIL.

3 FOR FOOD PROCESSING APPLICATIONS, USE

MOBIL WHITE REX 425 FOOD GRADE MOTOR OIL OR
OTHER FDA APPROVED OIL OF EQUIVALANT
SPECIFICATIONS.

Repair Parts List for Figure 3

Item Part Number Qty. Description
1  DD7646118 1 Filter/Regulator Air Lubricator Group
 Included in Filter Regulator Lubricator Kit, LATRFLK. Components not sold separately.

L4403 (rev. d) 5
 Figure 4: Air Pendant Assembly

8
RED GREEN
4 3

7
6
BLACK

RED
GREEN GREEN

11

Note: See top of next

1 10 page for parts list.

NOTES:

ASSEMBLE ONE LOCKWASHER UNDERNEATH EACH PUSH BUTTON AS SHOWN.

DISCARD REMAINING LOCKWASHERS AND SPACERS PROVIDED WITH ITEMS 3, 4 & 5.
12
TORQUE TO 13-16 IN-LB [1.5-1.8 Nm].

BLACK

RED

GREEN

6 L4403 (rev. d)
 Repair Parts List for Figure 4
Item Part Number Qty. Description
1 ✿ ♦ B1227503 1 O-Ring, Round
2 ♦ DA7570217 1 Cord Strap
3 ✥ ❂ ♦ DC3577379 1 Push Button, Green
4 ✥ ❂ ♦ DC3578379 1 Push Button, Red
5 ❂ ♦ DC8059379 2 Valve, Push Button
6 ❂ ♦ DC8060097 4 Elbow, 10 x 5/32"
7 ✿ ♦ DC8122424 1 Pendant Housing, Upper
8 ✝ ✿ DC8127026 1 Pendant Decal
9 ✿ ♦ DC9428008 4 Screw, Hi-Lo #8 x 1/2"
10 ✿ ♦ DC9425424 1 Lower Pendant
11 ✝ ✿ ♦ DD1394026 1 Decal, Pressure Relief
12 ♦ DD7851646 1 Air Tube, Pendant
 Items included in Pendant Service Repair Kit, DD7860900SR.
✿ Items included in Pendant Housing Kit, LATPHK.
❂ Items included in Pendant Push Button Kit, LATPBK.
✥ Items included in Pendant Push Button Cap Kit, LATPBCK.
✝ Items included in Decal Kit, LATDK.

Repair Parts List for Figure 5

Figure 5: Coverplate Components
Item Part Number Qty. Description

13 3
11 DD8014038 1 Adapter, 1/2
12 F100095-49 1 Fitting
13 DC8250006 1 Plug, Breather
12 5 3 25 ✝ DC9920026 1 Decal, Read Instructions
29 DD7692101 1 Coverplate
38 DD8506037 1 Plug, M21 Steel
39 DD8533037 1 Gasket
11 2
3 ✝ Item included in Decal Kit, LATDK.
38

39 25 NOTES:

2 APPLY LOCTITE 243.

3 TORQUE TO 8-10 LB-FT. [11-14 Nm].

29
5 APPLY PTFE TAPE TO THREADS.
LEAVE 1-2 LEADING THREADS EXPOSED.

See Fig. 10-11

L4403 (rev. d) 7
 Figure 6: Hydraulic Reservoir NOTES:

TORQUE TO 60-75 lb-in [6.8-8.5 Nm].

APPLY LOCTITE 243

3
SEE FIGURE 10 FOR LOCATION
OF MAGNET (ITEM 1).

14

3 2
14

See Fig. 1 14
1 3
8 13
14
8

9
7

VIEW A - ROLL CAGE

INSTALLATION

9
5

10

8 L4403 (rev. d)
 Repair Parts List for Figure 6
Item Part Number Qty. Description
1 ❖ C187018 1 Reservoir Magnet
2 ❖ CBE621028-1A 6 SHCS, Hex M6 x 20
3 ❖ CBE625028-1A 4 SHCS, Hex M6 x 30
4 ❖ CS235006 1 Plug, Int. Hex, 1/4” BSPP Steel
5 ❖ DB4519022 2 Oil Level Indicator
7 ✝ ❖ DC9596026 2 Decal, Enerpac Res
8
▼ ❖ DD7737037 1 Gasket, Reservoir
9 ❖ DD7813025 1 Reservoir, Hydraulic LAT
10 ✝ ❖ DD7997026 1 Decal, Product LAT
13
★▼ ❖ S3037 6 Gasket
14 ★ ▲▼ ❖ DD7164108 8 Washer, Sealing
❖ Items included in Reservoir Kit, DD7815900SR.
▼ Items included in Reservoir Gasket Kit, LATRGK.
▲ Item included in Roll Cage Service Repair Kit DD7816500SR.
★ Item included in Pump Seal Kit, LATPSK.
✝ Items included in Decal Kit, LATDK.

L4403 (rev. d) 9
 Figure 7: Control Valve
(underside view)

37
43

17 See Fig. 5

NOTES:

TORQUE TO 23-28 lb-ft [31-38 Nm].

TORQUE TO 8.4-9.0 lb-ft [11.4-12.2 Nm].

APPLY LOCTITE 243.

APPLY PTFE TAPE TO THREADS

LEAVE 1-2 LEAD THREADS EXPOSED.
36 TORQUE TO 10-12 lb-ft [13-16 Nm].

TORQUE UNION NUT ONTO TUBE (FIG. 10, ITEM 33)

TO 20-22 lb-ft [27-33 Nm].

1C APPLY GREASE TO SEAL ONLY.

1A APPLY GREASE TO BARB.
1B
TORQUE TO 28-30 LB-FT [38-40.7 Nm].
19

11
2

1
9 TORQUE FITTING TO 39-44 lb-ft [54-60 Nm]
INTO VALVE MANIFOLD (FIG. 8, ITEM 30).

ASSEMBLE CUTTING RING AND UNION NUT

7 ONTO TUBE (FIGURE 10, ITEM 33) BEFORE
TORQUING UNION NUT.
10

Repair Parts List for Figure 7

Item Part Number Qty. Description Item Part Number Qty. Description
1 45423SR
1 Cartridge, Relief Valve 10  TH630
1 Coupler, Male
1A ★ ✞B1112903 1 O-Ring 11 DC6629020 1 Dust Cap
1B ★ ✞B1112564 1 Backup Ring 17 DB2327095 1 Fitting, 1/4” BSP w/nut
1C ★ ✞DD8666476 1 Alum. Metal Washer 19  TR630
1 Coupler, Female
2 A1006245
4 Plug, Flush Hex 36 DD8017037 1 Gasket, Valve Manifold
7 CJ647096
1 Nipple, Pipe 1/4 NPT 37  DD8029268
1 Tubing, Inlet
8 CBB0819046-1B
2 Screw, HHCS M8 x 16 43  F100097-16
1 Fitting, Hose Barb
9 DC6187234
1 Dust Cap
 Items included in Valve Body Service Repair Kit, DD7707038SR. ★ Item included in Pump Seal Kit, LATPSK.
 Items included in Valve Service Repair Kit, DD7710900SR. ✞ Items included in UARV Seal Kit LATUARVSK.

10 L4403 (rev. d)
 Figure 8: Control Valve (top view)

13 5 2 6

See Figure 7
2 1 5

See Figure 7

7 16

14

2 1 5

4 3 101 30

2 1 5
102 See Figure 9

NOTES:

1 TORQUE TO 10-12 lb-ft [13-16 Nm]. 5 APPLY PTFE TAPE TO THREADS

LEAVE 1-2 LEAD THREADS EXPOSED.
2 TORQUE TO 23-28 lb-ft [31-38 Nm].
6 ORIENT AS SHOWN.
3 TORQUE TO 8.4-9.0 lb-ft [11.4-12.2 Nm].
7 TORQUE TO 45-50LB-IN [5.1-5.6 Nm].
4 APPLY LOCTITE 243.

Repair Parts List for Figure 8

Item Part Number Qty. Description Item Part Number Qty. Description
2  A1006245 4 Plug, Flush Hex 30  DD7077038 1 Manifold, Valve
13  DD6988223 1 Gauge 101  CCZ627028-1A 4 SHCS, M6 x 1", 35 mm
14  DD7578660 1 Valve, Pneumatic Op 102  B1012803 4 O-Ring
16  DD8024097 1 Elbow G1/4 x 5/32"
 Items included in Valve Body Service Repair Kit DD7707038SR.  Items included in Valve Seal Kit, LATVSK.
 Items included in Pneumatic Solenoid Valve Kit, DD7578660SR.  Items included in Gauge Kit, LATGK.
 Items included in Valve Service Repair Kit DD7710900SR.

L4403 (rev. d) 11
 Figure 9: Control Valve (B-side relief assembly)

4
11
6
18
3 17
10

17

12
5

NOTES:

TORQUE TO 60-75 lb-in [6.8-8.5 Nm].

HOLD FLAT POINT SET SCREW (ITEM 6) STATIONARY WHILE

TORQUING HEX JAM NUT (ITEM 4) TO KEEP IT FROM TURNING.

10 SEAT (ITEM 3) IS INCLUDED AND PREINSTALLED IF REPLACEMENT

MANIFOLD IS ORDERED (SEE FIG. 8, ITEM 30).

11 PRESSURE SETTING, B PORT RELIEF VALVE:

2600 PSI (+/- 100 PSI) [180 BAR (+/- 7 BAR)].

Repair Parts List for Figure 9

Item Part Number Qty. Description
3   A8015290 1 Seat
4   B1004124 1 Nut, Jam
5   B1005016 1 Ball, 0.188
6  BF3110027F 1 Set Screw
8   DC5625055 1 Nut, Acorn
12   DC6632110 1 Spring
17   G909167 1 Gasket
18   K1013 1 Guide

 Items included in Valve Body Service Repair Kit, DD7707038SR.

 Items included in Valve Service Repair Kit, DD7710900SR.
 Items included in B-Port Relief Valve Kit, LATBPRVK.

12 L4403 (rev. d)
 (This Page Intentionally Left Blank)

L4403 (rev. d) 13
 Figure 10: Pump Assembly (underside view)

9 NOTES:

14 27 TORQUE TO 10-12 lb-ft [13-16 Nm].

13
TORQUE FITTING TO 39-44 lb-ft [54-60 Nm].
INTO PUMP MANIFOLD (ITEM 31).

TORQUE TO 8.4-9.0 lb-ft [11.4-12.2 Nm].

APPLY LOCTITE 243.

27 34 5 INSTALL ONTO SHAFT WITH 5 DEGREE

ANGLED SURFACE TOWARDS ITEM #18.

TORQUE TO 8-10 lb-ft [11-14 Nm].

6 26
7 APPLY PTFE TAPE TO THREADS LEAVING 1-2
LEAD THREADS EXPOSED.
10
TORQUE UNION NUT ONTO TUBE (ITEM 33)
30 19 TO 20-22 lb-ft [27-33 Nm].

37 5 TORQUE TO 6-6.5 lb-ft [8.1-8.9 Nm].

12 PLACE RESERVOIR MAGNET (FIGURE 6, ITEM 1)
IN ONE OF THE SHADED LOCATIONS.

18

7
7

31 1 7

SEE SECTION A-A

7 1

29

33
UNION NUT
17 FITTING CUTTING
RING PRESSURE
TUBE

SECTION A-A
(ENLARGED VIEW - ITEMS 17 AND 33)

14 L4403 (rev. d)
 Repair Parts List for Figure 10
Item Part Number Qty. Description
1  A1006245 2 Plug, Flush, Hex, 27mm Steel, Teflon
6 ★    B1012803 3 O-Ring-Round, 0.375, 0.500, 0.063 Disogrin, 92
7  B1013028 3 Screw, SHCS, HS, 1/4-20, 1 1/4” long
9   CCA1012044-1A 1 Retaining Ring, Ext, 20mm, Steel
10  CCA1020044-1A 2 Retaining Ring, Ext 12mm, Steel
12  CCA615028-5C 1 Screw, Set, Cone, HS, M6 x 10
13     CCA627028-1A 6 Screw, SHCS, Hex, M6 x 35.0, Steel
14   CW302107 1 Bearing
17  DB2327095 1 Fitting, 1/4" BSPP, 8S w/Nut/Ring 800 Bar
18  DBS0005155-2 1 Bearing
19  DBS0005155-3 1 Bearing
26   DD1449051SR 1 Piston Block, 14mm
27   DD1450051SR 2 Piston Block, 6mm
29 DD7692101 1 Cover Plate
30   DD7720537 1 Eccentric Shaft
31  DD7721190 1 Pump Manifold
33  DD7751268 1 Pressure Tube, 8 x 2
34   DD7911006 1 Plug, Zero Leak Gold, 1/2"- 20
37  DY3858186 1 Counterbalance Spacer
 Items included in Pump Element Service Repair Kit, DD7726900SR.
 Items included in High Pressure Piston Block Kit, LATHPPBK.
 Items included in Low Pressure Piston Block Kit, LATLPPBK.
 Items included in Piston Block Bolt Kit, LATPBBK.
 Items included in Eccentric Shaft Kit, LATESK.
★ Item included in Pump Seal Kit, LATPSK.

L4403 (rev. d) 15
 Figure 11: Pump Assembly (top view - disassembled) 32 11
3

2
5
21 4
24
23

20

22

PRESS OUTLET CHECK SUB-ASSEMBLY (item 21)

INTO PUMP MANIFOLD (ITEM 30) USING A 10
TON CYLINDER AT 700-800 psi [48.3-55.1 bar].

16 TORQUE TO 30-35 in-lb [5.1-5.6 Nm].

LUBRICATE BACK-UP WASHER (ITEM 4) AND

O-RING (ITEM 5) WITH OIL PRIOR TO ASSEMBLY.
NOTES:
COIN PISTON BYPASS (ITEM 23) ONTO SEAT OF
TORQUE TO 10-12 lb-ft [13-16 Nm]. BYPASS VALVE BODY (ITEM 32).

APPLY LOCTITE 243. SET HEIGHT OF END CAP BYPASS (ITEM 22) TO
0.85 INCH ±0.01 [21.6 mm ±0.2].
TORQUE TO 32-39 lb-ft [43-53 Nm].
APPLY PTFE TAPE TO THREADS. LEAVE 1-2
SET TO 10,650-10,950 psi [734.5 - 755 bar]. LEADING THREADS EXPOSED.

Repair Parts List for Figure 11

Item Part Number Qty. Description
2  A1008245 1 Plug, Flush, Hex 18mm Steel, Teflon
3 ✿★✪  B1005803 2 O-Ring-Round, 0.0894, 0.219, 0.063, Disogrin, 92
4 ✿★✪  B1006564 1 Back Up, Split, 0.235, 0.250, 0.063 Disogrin, 92
5 ✿★✪  B1006803 1 O-Ring-Round, 0.125, 0.250, 0.063 Disogrin, 92
11 ✿ ✪  CCA525028-1A
4 Screw, SHCS, Hex, M5 x 30.0
16  DA8802900SR 1 Relief Valve Assembly (Factory pre-set to 10,650-10,950 psi)
17  DB2327095 1 Fitting, 1/4" BSPP, 8S w/Nut/Ring 800 Bar
18  DBS0005155-2 1 Bearing
19  DBS0005155-3 1 Bearing
20 ✿  DC394110 1 Bypass Spring
21  DC7904900SR 1 Outlet Check Sub Assembly
22 ✿  DC8374020 1 End Cap, Bypass
23 ✿  DC9292051 1 Piston Bypass, Parametric
24 ✿★✪  DC9293016 1 Ball, Nylon, 3/16"
32 ✿  DD7722190 1 Valve Body, Bypass
 Items included in Pump Element Service Repair Kit, DD7726900SR.
✪ Item included in Bypass Seal Kit, LATBPVSK.
★Item included in Pump Seal Kit, LATPSK. ✿ Item included in Bypass Valve Kit, LATBPVK.

16 L4403 (rev. d)
 Figure 12: Air Motor Assembly and Fittings (early models)

28

41

18 8
15 16 10 1 28

41 44

18 8
See Fig. 10, item 7
for capscrews.

NOTES:

1 TORQUE TO 10-12 lb-ft [13-16 Nm].

10 ORIENT AS SHOWN
(APPROXIMATE POSITION). See Fig. 10, item 7
16 APPLY PTFE TAPE TO THREADS. for capscrews.
LEAVE 1-2
LEADING THREADS EXPOSED.

18 IF REBUILDING: REMOVE AND DISCARD O-RING (ITEM 8). REMOVE

ANY SEALANT FROM COVER PLATE NOTES:
GROOVE AND MATING SURFACE
OF MOTOR (IF PRESENT). INSTALL NEW STYLE FLAT GASKET.
REFER TO FIGURE 13, ITEM 40.
1 TORQUE TO 10-12 lb-ft [13-16 Nm].

10 ORIENT AS SHOWN
(APPROXIMATE POSITION).
Repair Parts List for Figure 12
16APPLY PTFE TAPE TO THREADS. LEAVE 1-2
Item Part NumberLEADING THREADS
Qty. EXPOSED. Description
8 See Note 18 (above) 1 REMOVE
IF REBUILDING: O-Ring,
ANDAirDISCARD
Motor O-RING (ITEM 8). REMOVE
15 ANY SEALANT 1 FROM COVER
Pipe PLATE
Elbow, 90GROOVE
Degree AND MATING SURFACE
❂ DA1840095

OF MOTOR (IF PRESENT). INSTALL NEW STYLE FLAT GASKET.
28 ❂ DD7684116
REFER TO FIGURE
1 13, ITEM 40.
Muffler, Air Motor
41 ❂ DY3828259
1 Motor, Air Driven
44 ❂ F100097-61
1 Connector, NPTF Male
❂ Items included in Motor Service Kit, LATMTR.

L4403 (rev. d) 17
 Figure 13: Air Motor Assembly and Fittings (later models)

16 10 1 15 28 1 16

NOTES:
41
1 TORQUE TO 10-12 lb-ft [13-16 Nm].

10 ORIENT AS SHOWN (APPROXIMATE POSITION).

.
18 40
16 APPLY PTFE TAPE TO THREADS. LEAVE 1-2
LEADING THREADS EXPOSED.

18 REMOVE PROTECTIVE BACKING AND ADHERE

44 1 16 ADHESIVE SIDE TO MOTOR FLANGE.

See Fig. 10, item 7

for capscrews.

Repair Parts List for Figure 13

Item Part Number Qty. Description
15 ❂ DA184095
1 Pipe Elbow, 90 Degree
28 ❂ DD7684116
1 Muffler, Air Motor
40 ❂ DD8533037
1 Gasket, Motor LAT
41 ❂ DY3828259
1 Motor, Air Driven
44 ❂ F100097-61
1 Connector, NPTF Male
❂ Items included in Motor Service Repair Kit, LATMTR.

18 L4403 (rev. d)
 WARNING Shut off compressed air supply, disconnect air supply line and be sure all hydraulic pressure is completely relieved before performing any
disassembly or repair procedures. Verify that hydraulic pressure gauge indicates zero (0) psi/bar.

L4403 (rev. d)
STOP ADV/RET
RED REMOTE GREEN
PENDANT

MOTOR
FILTER, CONTROL
REGULATOR, VALVE
LUBRICATOR
ASSY A B

HYDRAULIC
PUMP HYDRAULIC
AIR MOTOR VALVE
SUBSYSTEM
AND MUFFLER SUBSYSTEM

Figure 14: Air Logic & Schematic Diagram

19
 www.enerpac.com
© 2021 Enerpac, All Rights Reserved.