Projector Manual 7409

PJD5132/PJD5232L/PJD5134/
PJD5234L/PJD5533w
DLP Projector
User Guide
IMPORTANT: Please read this User Guide to obtain important information on installing
and using your product in a safe manner, as well as registering your product for
future service. Warranty information contained in this User Guide will describe your
limited coverage from ViewSonic Corporation, which is also found on our web site at
http://www.viewsonic.com in English, or in specific languages using the Regional
selection box in the upper right corner of our website. “Antes de operar su equipo lea cu
idadosamente las instrucciones en este manual”
Model No. VS14926/VS14929/VS14928/VS14930/VS14117

Compliance Information
FCC Statement
This device complies with part 15 of FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy, and if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
yy Reorient or relocate the receiving antenna.
yy Increase the separation between the equipment and receiver.
yy Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
yy Consult the dealer or an experienced radio/TV technician for help.
Warning: You are cautioned that changes or modifications not expressly approved by the
party responsible for compliance could void your authority to operate the equipment.
For Canada
CAN ICES-3(B)/NMB-3(B)
CE Conformity for European Countries

The device complies with the EMC Directive 2004/108/EC and Low Voltage
Directive 2006/95/EC.
Following information is only for EU-member states:

The mark is in compliance with the Waste Electrical and Electronic Equipment Directive
2002/96/EC (WEEE).
The mark indicates the requirement NOT to dispose the equipment including any spent
or discarded batteries or accumulators as unsorted municipal waste, but use the return
and collection systems available.
If the batteries, accumulators and button cells included with this equipment, display
the chemical symbol Hg, Cd, or Pb, then it means that the battery has a heavy metal
content of more than 0.0005% Mercury or more than, 0.002% Cadmium, or more than
0.004% Lead.
i
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this unit near water.
6. Clean with a soft, dry cloth.
7. Do not block any ventilation openings. Install the unit in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other
devices (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug
has two blades with one wider than the other. A grounding type plug has two blades and a
third grounding prong. The wide blade and the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs. Convenience
receptacles and the point where they exit from the unit. Be sure that the power outlet is
located near the unit so that it is easily accessible.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the unit. When a cart is used, use caution when moving
the cart/unit combination to avoid injury from tipping over.
13. Unplug this unit when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the unit has
been damaged in any way, such as: if the power-supply cord or plug is damaged, if liquid
is spilled onto or objects fall into the unit, if the unit is exposed to rain or moisture, or if the
unit does not operate normally or has been dropped.
ii
Declaration of RoHS2 Compliance
This product has been designed and manufactured in compliance with Directive 2011/65/
EU of the European Parliament and the Council on restriction of the use of certain hazardous
substances in electrical and electronic equipment (RoHS2 Directive) and is deemed to comply
with the maximum concentration values issued by the European Technical Adaptation Commit-
tee (TAC) as shown below:
Proposed Maximum
Substance Actual Concentration
Concentration
Lead (Pb) 0.1% < 0.1%

Mercury (Hg) 0.1% < 0.1%
Cadmium (Cd) 0.01% < 0.01%
Hexavalent Chromium (Cr6+) 0.1% < 0.1%
Polybrominated biphenyls (PBB) 0.1% < 0.1%
Polybrominated diphenyl ethers (PBDE) 0.1% < 0.1%
Certain components of products as stated above are exempted under the Annex III of the
RoHS2 Directives as noted below:
Examples of exempted components are:
1. Mercury in cold cathode fluorescent lamps and external electrode fluorescent lamps
(CCFL and EEFL) for special purposes not exceeding (per lamp):
(1) Short length (≦500 mm): maximum 3.5 mg per lamp.
(2) Medium length (＞500 mm and ≦1,500 mm): maximum 5 mg per lamp.
(3) Long length (＞1,500 mm): maximum 13 mg per lamp.
2. Lead in glass of cathode ray tubes.
3. Lead in glass of fluorescent tubes not exceeding 0.2% by weight.
4. Lead as an alloying element in aluminium containing up to 0.4% lead by weight.
5. Copper alloy containing up to 4% lead by weight.
6. Lead in high melting temperature type solders (i.e. lead-based alloys containing 85% by
weight or more lead).
7. Electrical and electronic components containing lead in a glass or ceramic other than
dielectric ceramic in capacitors, e.g. piezoelectronic devices, or in a glass or ceramic
matrix compound.
iii
Copyright Information
Copyright © ViewSonic® Corporation, 2013. All rights reserved.
Macintosh and Power Macintosh are registered trademarks of Apple Inc.
Microsoft, Windows, Windows NT, and the Windows logo are registered trademarks of Microsoft
Corporation in the United States and other countries.
ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered trademarks
of ViewSonic Corporation.
VESA is a registered trademark of the Video Electronics Standards Association. DPMS and
DDC are trademarks of VESA.
PS/2, VGA and XGA are registered trademarks of International Business Machines Corporation.
Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors or omis-
sions contained herein; nor for incidental or consequential damages resulting from furnishing
this material, or the performance or use of this product.
In the interest of continuing product improvement, ViewSonic Corporation reserves the right to
change product specifications without notice. Information in this document may change without
notice.
No part of this document may be copied, reproduced, or transmitted by any means, for any
purpose without prior written permission from ViewSonic Corporation.
Product Registration
To meet your future needs, and to receive any additional product information as it becomes
available, please register your product on the Internet at: www.viewsonic.com. The ViewSonic®
Wizard CD-ROM also provides an opportunity for you to print the registration form, which you
may mail or fax to ViewSonic.
For Your Records

Product Name: PJD5132/PJD5232L/PJD5134/PJD5234L/PJD5533w
ViewSonic DLP Projector
Model Number: VS14926/VS14929/VS14928/VS14930/VS14117
Document Number: PJD5132/PJD5232L/PJD5134/PJD5234L/PJD5533w_
UG_ENG Rev. 1B 05-07-13
Serial Number: ___________________________________________
Purchase Date: ___________________________________________
Product disposal at end of product life

The lamp in this product contains mercury which can be dangerous to you and the environment.
Please use care and dispose of in accordance with local, state or federal laws.
ViewSonic respects the environment and is committed to working and living green. Thank you
for being part of Smarter, Greener Computing. Please visit ViewSonic website to learn more.
USA & Canada: http://www.viewsonic.com/company/green/recycle-program/
Europe: http://www.viewsoniceurope.com/uk/support/recycling-information/
Taiwan: http://recycle.epa.gov.tw/recycle/index2.aspx
iv
Table of contents
Important safety Using the projector in standby mode. 38
Shutting down the projector .............. 39
instructions .......................2
Menu operation.................................. 40
Introduction......................4 Maintenance ...................50
Projector features ................................. 4
Care of the projector .......................... 50
Shipping contents................................. 5
Lamp information .............................. 51
Projector exterior view......................... 6
Controls and functions ......................... 7 Troubleshooting .............57
Positioning your Specifications ..................58
projector..........................12 Projector specifications...................... 58
Choosing a location............................ 12 Dimensions ........................................ 60
Projection dimensions ........................ 13 Ceiling mount installation ................. 60
Timing chart ...................................... 61
Connection ......................15
Connecting a computer or monitor .... 16 Copyright information...63
Connecting Video source devices ...... 17 Appendix.........................64
Operation ........................20 IR control table .................................. 64
Starting up the projector..................... 20 RS232 command table....................... 66
Using the menus................................. 21
Utilizing the password function ......... 22
Switching input signal........................ 25
Adjusting the projected image ........... 26
Magnifying and searching for details. 27
Selecting the aspect ratio ................... 28
Optimizing the image......................... 31
Setting the presentation timer ............ 35
Hiding the image................................ 36
Locking control keys.......................... 36
Freezing the image ............................. 36
Operating in a high altitude
environment ....................................... 36
Using the CEC function ..................... 37
Using the 3D functions ...................... 37
1
Important safety instructions
Your projector is designed and tested to meet the latest standards for safety of information
technology equipment. However, to ensure safe use of this product, it is important that you
follow the instructions mentioned in this manual and marked on the product.
Safety Instructions
1. Please read this manual before you operate your projector. Save it for future
reference.
2. Do not look straight at the projector lens during operation. The intense light beam
may damage your eyes.
3. Refer servicing to qualified service personnel.
4. Always open the lens shutter or remove the lens cap when the projector lamp is
on.
5. In some countries, the line voltage is NOT stable. This projector is designed to operate
safely within a mains voltage between 100 to 240 volts AC, but could fail if power
cuts or surges of ±10 volts occur. In areas where the mains voltage may fluctuate
or cut out, it is recommended that you connect your projector through a power
stabilizer, surge protector or uninterruptible power supply (UPS).
6. Do not block the projection lens with any objects when the projector is under
operation as this could cause the objects to become heated and deformed or even
cause a fire. To temporarily turn off the lamp, press BLANK on the projector or
remote control.
7. The lamp becomes extremely hot during operation. Allow the projector to cool for
approximately 45 minutes prior to removing the lamp assembly for replacement.
8. Do not operate lamps beyond the rated lamp life. Excessive operation of lamps
beyond the rated life could cause them to break on rare occasions.
9. Never replace the lamp assembly or any electronic components unless the projector is
unplugged.
10. Do not place this product on an unstable cart, stand, or table. The product may fall,
sustaining serious damage.
11. Do not attempt to disassemble this projector. There are dangerous high voltages inside
which may cause death if you should come into contact with live parts. The only user
serviceable part is the lamp which has its own removable cover.
Under no circumstances should you ever undo or remove any other covers. Refer
servicing only to suitably qualified professional service personnel.
12. Do not place this projector in any of the following environments.
- Space that is poorly ventilated or confined. Allow at least 50 cm clearance from walls
and free flow of air around the projector.
- Locations where temperatures may become excessively high, such as the inside of a
car with all windows rolled up.
- Locations where excessive humidity, dust, or cigarette smoke may contaminate optical
components, shortening the projector's life span and darkening the picture.
- Locations near fire alarms
- Locations with an ambient temperature above 40°C / 104°F
- Locations where the altitudes are higher than 3000 m (10000 feet).
2
13. Do not block the ventilation holes. If the ventilation holes are seriously obstructed,
overheating inside the projector may result in a fire.
- Do not place this projector on a blanket, bedding or any other soft surface.
- Do not cover this projector with a cloth or any other item.
- Do not place inflammables near the projector.
14. Always place the projector on a level, horizontal surface during operation.
- Do not use if tilted at an angle of more than 10 degrees left to right, nor at angle of
more than 15 degrees front to back. Using the projector when it is not fully horizontal
may cause a malfunction of, or damage to, the lamp.
15. Do not stand the projector on end vertically. Doing so may cause the projector to fall
over, causing injury or resulting in damage to the projector.
16. Do not step on the projector or place any objects upon it. Besides probable physical
damage to the projector, doing so may result in accidents and possible injury.
17. Do not place liquids near or on the projector. Liquids spilled into the projector may
cause it to fail. If the projector does become wet, disconnect it from the power
supply's wall socket and call your local service center to have the projector serviced.
18. This product is capable of displaying inverted pictures for ceiling mount installation.
Use only qualified ceiling mount kit for mounting the projector and ensure it is
securely installed.
19. When the projector is under operation, you may sense some heated air and odor from
its ventilation grill. It is a normal phenomenon and not a product defect.
20. Do not use the Security bar for transporting or installation. It should be used with a
commercially available theft prevention cable.
Safety instructions for ceiling mounting of the

projector
We want you to have a pleasant experience using your projector, so we need to bring this
safety matter to your attention to prevent damage to person and property.
If you intend to mount your projector on the ceiling, we strongly recommend that you use a
proper fitting projector ceiling mount kit and that you ensure it is securely and safely
installed.
If you use an inappropriate projector ceiling mount kit, there is a safety risk that the
projector may fall from the ceiling due to an improper attachment through the use of the
wrong gauge or length screws.
You can purchase a projector ceiling mount kit from the place you purchased your projector.
We recommends that you also purchase a separate Kensington lock compatible security
cable and attach it securely to both the Kensington lock slot on the projector and the base of
the ceiling mount bracket. This will perform the secondary role of restraining the projector
should its attachment to the mounting bracket become loose.
3
Introduction
Projector features
The projector integrates high-performance optical engine projection and a user-friendly
design to deliver high reliability and ease of use.
The projector offers the following features.
• Dynamic PC and Dynamic Movie functions adjusting the power consumption of the
lamp according to the brightness of the image being projected
• DynamicEco Timer function decreasing the power consumption of the lamp by up to
30% when no input signal can be detected for a set period of time.
• Presentation timer for better control of time during presentations
• Supports 3D display
• Color Management allowing color adjustments to your liking
• Less than 0.5W power consumption when power saving mode is turned on
• Screen Color correction allowing projection on surfaces of several predefined colors
• Quick auto search speeding up the signal detecting process
• Color and Reference modes providing choices for different projection purposes
• Selectable quick power off function
• One-key auto-adjustment to display the best picture quality
• Digital keystone correction to correct distorted images
• Adjustable color management control for data/video display
• Ability to display 1.07 billion colors
• Multi-language On-Screen Display (OSD) menus
• Switchable normal and economic modes to reduce the power consumption
• Component HDTV compatibility (YPbPr)
• HDMI CEC (Consumer Electronics Control) function allows synchronized power ON/
OFF operation between the projector and a CEC-compatible device connected to the
HDMI input of the projector (PJD5134/PJD5234L/PJD5533w models only)
• The apparent brightness of the projected image will vary depending on the ambient
lighting conditions, selected input signal contrast/brightness settings, and is directly
proportional to projection distance.
• The lamp brightness will decline over time and may vary within the lamp manufacturers
specifications. This is normal and expected behavior.
4
Shipping contents
Carefully unpack and verify that you have all of the items shown below. If any of these
items are missing, please contact your place of purchase.
Standard accessories
The supplied accessories will be suitable for your region, and may differ from those
illustrated.
Projector Power Cord VGA Cable
Multi-language user
Quick Start Guide Remote Control & Batteries
manual DVD
Optional accessories
1. Replacement lamp
2. Soft carry case
3. VGA-Component adapter
5
Projector exterior view
1. External control panel
Front/upper side
(See "Projector" on page 7 for
1 details.)
6 2. Lamp cover
2
3. Vent (heated air exhaust)
4. Front IR remote sensor
3
5. Adjuster foot
4
6. Focus and Zoom rings
5 7. Projection lens
7 8. RS-232 control port
9. Type B USB port
10. HDMI port
11. RGB (PC)/Component video
(YPbPr/YCbCr) signal input
Rear/lower side socket-2
12. RGB (PC)/Component video
PJD5132/PJD5232L (YPbPr/YCbCr) signal input
8 9 11 12 13 14 15 16 socket-1
13. RGB signal output socket
14. S-Video input socket
15. Video input socket
18 17 16. Audio signal input socket
Audio signal output socket
17. Kensington anti-theft lock slot
18. AC power cord inlet
PJD5134/PJD5234L/PJD5533w
8 9 10 11 12 13 14 15 16
18 17
Warning
• THIS APPARATUS MUST BE EARTHED.
• When installing the unit, incorporate a readily accessible disconnect device in the fixed wiring,
or connect the power plug to an easily accessible socket-outlet near the unit. If a fault should
occur during operation of the unit, operate the disconnect device to switch the power supply
off, or disconnect the power plug.
6
Controls and functions
Projector
1
2
3 7
4 8
5 9
MENU
EXIT
3 10
6 11
12
1. Focus ring 8. Right

Adjusts the focus of the projected image. Activates panel key lock.
2. Zoom ring
When the On-Screen Display (OSD)
Adjusts the size of the image. menu is activated, the #3, #4, and #8 keys
3. Keystone/Arrow keys ( / Up, / are used as directional arrows to select the
Down) desired menu items and to make
Manually corrects distorted images adjustments.
resulting from an angled projection. 9. LAMP indicator light
4. Left/Blank Indicates the status of the lamp. Lights up
Hides the screen picture. or flashes when the lamp has developed a
5. POWER indicator light problem.
Lights up or flashes when the projector is 10. AUTO
under operation. Automatically determines the best picture
I
I timings for the displayed image.
POWER
11. TEMPerature indicator light
Toggles the projector between standby
Lights up red if the projector's
mode and on.
temperature becomes too high.
6. SOURCE
12. MODE/ENTER
Displays the source selection bar.
Selects an available picture setup mode.
7. MENU/EXIT
Enacts the selected On-Screen Display
Turns on the On-Screen Display (OSD)
(OSD) menu item.
menu. Goes back to previous OSD menu,
exits and saves menu settings.
7
Remote control
1 18
2
3 19
4
5
6
4
8 7
20
9
21
10
11
12 22
13 14
15 23
16 24
17 25
To use the remote mouse control keys 6. Enter

(Page Up, Page Down, , and ), see Enacts the selected On-Screen Display
"Using the remote mouse control" on
page 10 for details. (OSD) menu item.
7. My Button
1. I
I
POWER Allows user to define a short cut key
Toggles the projector between standby on the remote control, and the function
mode and on. item is selected in OSD menu.
2. Source selection keys (VGA/Video) 8. Menu
Selects an input source for display. Turns on the On-Screen Display
VGA (OSD) menu.
Selects D-Sub / Comp. 1 or D-Sub / 9.
Comp. 2 source for display. Performs the same function as the left
Video mouse button when the mouse mode is
Selects Video source for display. activated.
HDMI is only available on models with
10.
HDMI input. Performs the same function as the
right mouse button when the mouse
3. Source
mode is activated.
Displays the source selection bar. 11. Mouse
4. Keystone keys ( / ) Switches between the normal and
Manually corrects distorted images mouse modes.
resulting from an angled projection.
Page Up, Page Down, , : active
5. / / / after pressing Mouse. An icon appears
Selects the desired menu items and on the screen to indicate the activation
makes adjustments. of the mouse mode.
8
12. Magnify 19. Color Mode
Displays the zoom bar that magnifies or Selects an available picture setup mode.
reduces the projected picture size. 20. Exit
13. Lock Goes back to previous OSD menu, exits
Activates or deactivates panel key lock. and saves menu settings.
14. Freeze 21. PgUp (Page Up)/PgDn (Page Down)
Freezes the projected image. Operates your display software program
15. Pattern (on a connected PC) which responds to
Displays embedded test pattern. page up/down commands (like Microsoft
16. Blank PowerPoint) when the mouse mode is
activated.
Hides the screen picture.
22. Volume keys (+, -)
17. DynamicEco™
Magnifies or reduces the volume level.
Decreases the power consumption of the
lamp by up to 30%. 23.
• It takes some time to initiate this Toggles the projector audio between on
function. Make sure the projector has
been turned on for more than 4 minutes. and off.
If the projector is resumed by using the 24. Aspect
Smart Restart feature, this function can
Selects the display aspect ratio.
be executed immediately.
•After 30 minutes of continuous use in 25. Timer
D.Eco mode, the projector will revert to Displays the presentation timer settings
Normal mode for 5 minutes before menu.
switching back to D.Eco mode.
18. Auto Sync
Automatically determines the best picture
timings for the displayed image.
Remote control code

The projector can be assigned to two different remote control codes, A or B. When several
adjacent projectors are in operation at the same time, switching the remote control codes
can prevent interference from other remote controls. Set the remote control code for the
projector first before changing that for the remote control.
To switch the code for the projector, select A or B in the SYSTEM SETTING:
ADVANCED > Remote Control Code menu.
To switch the code for the remote control, press PgUp and PgDn buttons on the remote
control together for 5 seconds or more. The initial code is set to A.
If different codes are set on the projector and remote control, there will be no response from
the remote control. When that happens, switch the code for the remote control again.
9
Using the remote mouse control
The capability of operating your computer with the remote control gives you more
flexibility when delivering presentations.
1. Connect the projector to your PC or notebook with a USB cable prior to using the
remote control in place of your computer’s mouse. See "Connecting a computer" on
page 16 for details.
2. Set the input signal to D-Sub / Comp. 1, D-Sub / Comp. 2 or HDMI.
The HDMI input is only available on the PJD5134/PJD5234L/PJD5533w models.
3. Press Mouse on the remote control to switch from the normal mode to the mouse
mode. An icon appears on the screen to indicate the activation of the mouse mode.
4. Perform the desired mouse controls on your remote control.
• To move the cursor on the screen, press / / / .
• To left-click, press .
• To right-click, press .
• To operate your display software program (on a connected PC) which responds to
page up/down commands (like Microsoft PowerPoint), press PgUp/PgDn.
• To return to the normal mode, press Mouse again or other keys except for the
mouse related multi-function keys.
Remote control effective range

The Infra-Red (IR) remote control is located on the front
of the projector. The remote control must be held at an
angle within 30 degrees perpendicular to the projector's
IR remote control sensor to function correctly. The
distance between the remote control and the sensor should
not exceed 8 meters (~ 26 feet). Appr
ox. 1
5°
Make sure that there are no obstacles between the remote
control and the IR sensor on the projector that might
obstruct the infra-red beam.
10
Replacing the remote control batteries
1. To open the battery cover, turn the remote control over to view its back, push on the
finger grip on the cover and slide it in the direction of the arrow as illustrated. The
cover will slide off.
2. Remove any existing batteries (if necessary) and install two AAA batteries observing
the battery polarities as indicated in the base of the battery compartment. Positive (+)
goes to positive and negative (-) goes to negative.
3. Refit the cover by aligning it with the base and sliding it back down into position.
Stop when it clicks into place.
• Avoid leaving the remote control and batteries in an excessive heat or humid environment
like the kitchen, bathroom, sauna, sunroom or in a closed car.
• Replace only with the same or equivalent type recommended by the battery manufacturer.
• Dispose of the used batteries according to the manufacturer's instructions and local
environment regulations for your region.
• Never throw the batteries into a fire. There may be danger of an explosion.
• If the batteries are dead or if you will not be using the remote control for an extended
period of time, remove the batteries to avoid damage to the remote control from possible
battery leakage.
11
Positioning your projector
Choosing a location
Your room layout or personal preference will dictate which installation location you select.
Take into consideration the size and position of your screen, the location of a suitable power
outlet, as well as the location and distance between the projector and the rest of your
equipment.
Your projector is designed to be installed in one of four possible installation locations:
1. Front Table
Select this location with the projector placed near
the floor in front of the screen. This is the most
common way to position the projector for quick
setup and portability.
2. Front Ceiling
Select this location with the projector suspended
upside-down from the ceiling in front of the
screen.
Purchase the projector ceiling mount kit from your
dealer to mount your projector on the ceiling.
Set Front Ceiling in the SYSTEM SETTING:
BASIC > Projector Position menu after you turn
the projector on.
3. Rear Ceiling
Select this location with the projector suspended
upside-down from the ceiling behind the screen.
Note that a special rear projection screen and the
projector ceiling mounting kit are required for this
installation location.
Set Rear Ceiling in the SYSTEM SETTING:
the projector on.
4. Rear Table
Select this location with the projector placed near
the floor behind the screen.
Note that a special rear projection screen is
required.
Set Rear Table in the SYSTEM SETTING:
the projector on.
12
Projection dimensions
Refer to "Dimensions" on page 60 for the center of lens dimensions of this projector before
calculating the appropriate position.
The "screen" mentioned below refers to the projection screen usually consisting of a surface
and a support structure
PJD5132/PJD5232L/PJD5134/PJD5234L
• 4:3 image on a 4:3 screen
(b) (a)
(a) (e)
(d) (f)
(c)
(c)
(d)
(f)
(e) (b)
(b) (a)
(a) (e)
(f)
(d)
(c)
(c) (d)
(f)
(b)
(e)
(e): Screen (f): Center of lens
4:3 image on a 4:3 Screen 16:9 image on a 4:3 Screen

(a) Screen
(b) Projection (c) Image (d) Vertical (b) Projection distance (c) Image (d) Vertical
Size
distance [m (inch)] height offset [m (inch)] height offset
[inch (m)]
min. max. [cm (inch)] [cm (inch)] min. max. [cm (inch)] [cm (inch)]
30 (0.8) 1.1 (45) 1.2 (49) 46 (18) 5 (1.8) 1.1 (45) 1.2 (49 34 (14) 10.3 (4.1)
40 (1.0) 1.5 (59) 1.7 (65) 61 (24) 6 (2.4) 1.5 (59) 1.7 (65) 46 (18) 13.7 (5.4)
50 (1.3) 1.9 (74) 2.1 (82) 76 (30) 8 (3.0) 1.9 (74) 2.1 (82) 57 (23) 17.1 (6.8)
60 (1.5) 2.3 (89) 2.5 (98) 91 (36) 9 (3.6) 2.3 (89) 2.5 (98) 69 (27) 20.6 (8.1)
70 (1.8) 2.6 (104) 2.9 (114) 107 (42) 11 (4.2) 2.6 (104) 2.9 (114) 80 (32) 24.0 (9.5)
80 (2.0) 3.0 (119) 3.3 (131) 122 (48) 12 (4.8) 3.0 (119) 3.3 (131) 91 (36) 27.4 (10.8)
90 (2.3) 3.4 (134) 3.7 (147) 137 (54) 14 (5.4) 3.4 (134) 3.7 (147) 103 (41) 30.9 (12.2)
100 (2.5) 3.8 (149) 4.2 (163) 152 (60) 15 (6.0) 3.8 (149) 4.2 (163) 114 (45) 34.3 (13.5)
120 (3.0) 4.5 (178) 5.0 (196) 183 (72) 18 (7.2) 4.5 (178) 5.0 (196) 137 (54) 41.1 (16.2)
150 (3.8) 5.7 (223) 6.2 (245) 229 (90) 23 (9.0) 5.7 (223) 6.2 (245) 171 (68) 51.4 (20.3)
200 (5.1) 7.5 (297) 8.3 (327) 305 (120) 30 (12.0) 7.5 (297) 8.3 (327) 229 (90) 68.6 (27.0)
250 (6.4) 9.4 (371) 10.4 (409) 381 (150) 38 (15.0) 9.4 (371) 10.4 (409) 286 (113) 85.7 (33.8)
300 (7.6) 11.3 (446) 12.5 (490) 457 (180) 46 (18.0) 11.3 (446) 12.5 (490) 343 (135) 102.9 (40.5)
13
PJD5533w
(b) (a)
(a) (e)
(d) (f)
(c)
(c)
(d)
(f)
(e) (b)

(b) (a)
(a) (e)
(f)
(d)
(c)
(c)
(f) (d)
(e) (b)
(e): Screen (f): Center of lens
16:10 image on a 16:10 Screen 16:10 image on a 4:3 Screen

(a) Screen
(b) Projection distance (c) Image (d) Vertical (b) Projection distance (c) Image (d) Vertical
Size
[m (inch)] height offset [m (inch)] height offset
[inch (m)]
min. max. [cm (inch)] [cm (inch)] min. max. [cm (inch)] [cm (inch)]
30 (0.8) 0.97 (38) 1.06 (42) 40 (16) 0 (0.0) 0.91 (36) 1.00 (40) 38 (15) 3.8 (1.5)
40 (1.0) 1.29 (51) 1.42 (56) 54 (21) 0 (0.0) 1.22 (48) 1.34 (53) 51 (20) 5.1 (2.0)
50 (1.3) 1.61 (64) 1.77 (70) 67 (26) 0 (0.0) 1.52 (60) 1.67 (66) 64 (25) 6.4 (2.5)
60 (1.5) 1.94 (76) 2.13 (84) 81 (32) 0 (0.0) 1.83 (72) 2.01 (79) 76 (30) 7.6 (3.0)
70 (1.8) 2.26 (89) 2.48 (98) 94 (37) 0 (0.0) 2.13 (84) 2.34 (92) 89 (35) 8.9 (3.5)
80 (2.0) 2.58 (102) 2.84 (112) 108 (42) 0 (0.0) 2.43 (96) 2.68 (105) 102 (40) 10.2 (4.0)
90 (2.3) 2.90 (114) 3.19 (126) 121 (48) 0 (0.0) 2.74 (108) 3.01 (119) 114 (45) 11.4 (4.5)
100 (2.5) 3.23 (127) 3.55 (140) 135 (53) 0 (0.0) 3.04 (120) 3.35 (132) 127 (50) 12.7 (5.0)
120 (3.0) 3.87 (152) 4.26 (168) 162 (64) 0 (0.0) 3.65 (144) 4.02 (158) 152 (60) 15.2 (6.0)
150 (3.8) 4.84 (191) 5.32 (210) 202 (79) 0 (0.0) 4.56 (180) 5.02 (198) 191 (75) 19.1 (7.5)
200 (5.1) 6.45 (254) 7.10 (279) 269 (106) 0 (0.0) 6.09 (240) 6.70 (264) 254 (100) 25.4 (10.0)
250 (6.4) 8.06 (318) 8.87 (349) 337 (132) 0 (0.0) 7.61 (300) 8.37 (329) 318 (125) 31.8 (12.5)
300 (7.6) 9.68 (381) 10.65 (419) 404 (159) 0 (0.0) 9.13 (359) 10.04 (395) 381 (150) 38.1 (15.0)
There is 3% tolerance among these numbers due to optical component variations. It is

recommended that if you intend to permanently install the projector, you should physically
test the projection size and distance using the actual projector in situ before you permanently
install it, so as to make allowance for this projector's optical characteristics. This will help you
determine the exact mounting position so that it best suits your installation location.
14
Connection
When connecting a signal source to the projector, be sure to:
1. Turn all equipment off before making any connections.
2. Use the correct signal cables for each source.
3. Ensure the cables are firmly inserted.
• In the connections shown below, some cables may not be included with the projector (see
"Shipping contents" on page 5). They are commercially available from electronics stores.
• The connection illustrations below are for reference only. The rear connecting jacks
available on the projector vary with each projector model.
• For detailed connection methods, see pages 16-19.
Notebook or desktop computer

A/V device
Monitor
(VGA) or (DVI)
1 7
1 2 3
8 4 7 5 6 Speakers 7
PJD5134/
PJD5234L/
PJD5533w
PJD5132/
PJD5232L
1. VGA cable 5. S-Video cable

2. VGA to DVI-A cable 6. Video cable
3. USB cable 7. Audio cable
4. Component Video to VGA (D-Sub) 8. HDMI cable
adapter cable
15
Connecting a computer or monitor
Connecting a computer
The projector provides two VGA input sockets that allow you to connect them to both
IBM® compatibles and Macintosh® computers. A Mac adapter is needed if you are
connecting legacy version Macintosh computers.
To connect the projector to a notebook or desktop computer:
1. Take the supplied VGA cable and connect one end to the D-Sub output socket of the
computer.
2. Connect the other end of the VGA cable to the COMPUTER IN 1 or COMPUTER
IN 2 signal input socket on the projector.
3. If you wish to use the remote paging function, take a USB cable and connect the
larger end to the USB port of the computer, and smaller end to the MINI USB socket
on the projector. See "Using the remote mouse control" on page 10 for details.
Many notebooks do not turn on their external video ports when connected to a projector.
Usually a key combo like FN + F3 or CRT/LCD key turns the external display on/off. Locate a
function key labeled CRT/LCD or a function key with a monitor symbol on the notebook. Press
FN and the labeled function key simultaneously. Refer to your notebook's documentation to
find your notebook's key combination.
Connecting a monitor
If you want to view your presentation close-up on a monitor as well as on the screen, you
can connect the MONITOR OUT signal output socket on the projector to an external
monitor with a VGA cable following the instructions below:
To connect the projector to a monitor:
1. Connect the projector to a computer as described in "Connecting a computer" on page
16.
2. Take a suitable VGA cable (only one supplied) and connect one end of the cable to the
D-Sub input socket of the video monitor.
Or if your monitor is equipped with a DVI input socket, take a VGA to DVI-A cable
and connect the DVI end of the cable to the DVI input socket of the video monitor.
3. Connect the other end of the cable to the MONITOR OUT socket on the projector.
• The MONITOR OUT output only works when COMPUTER IN 1 connection is made to the
projector.
• To use this connection method when the projector is in standby mode, turn on the Active
VGA Out function under the SYSTEM SETTING: BASIC > Standby Settings menu.
16
Connecting Video source devices
You can connect your projector to various Video source devices that provide any one of the
following output sockets:
• HDMI
• Component Video
• S-Video
• Video (composite)
You need only connect the projector to a Video source device using just one of the above
connecting methods, however each provides a different level of video quality. The method
you choose will most likely depend upon the availability of matching terminals on both the
projector and the Video source device as described below:
Best video quality
The best available video connection method is HDMI. If your source device is equipped
with a HDMI socket, you can enjoy uncompressed digital video quality.
See "Connecting an HDMI device" on page 18 for how to connect the projector to a HDMI
source device and other details.
The HDMI input is only available on the PJD5134/PJD5234L/PJD5533w models.
If no HDMI source is available, the next best video signal is Component video (not to be
confused with composite video). Digital TV tuner and DVD players output Component
video natively, so if available on your devices, this should be your connection method of
choice in preference to (composite) video.
See "Connecting a Component Video source device" on page 18 for how to connect the
projector to a component video device.
Better video quality
The S-Video method provides a better quality analog video than standard composite Video.
If you have both composite Video and S-Video output terminals on your Video source
device, you should elect to use the S-Video option.
See "Connecting an S-Video source device" on page 19 for how to connect the projector to
an S-Video device.
Least video quality
Composite Video is an analog video and will result in a perfectly acceptable, but less than
optimal result from your projector, being the least video quality of the available methods
described here.
See "Connecting a composite Video source device" on page 19 for how to connect the
projector to a composite Video device.
Connecting audio
The projector has one built-in mono speaker which is designed to provide basic audio
functionality accompanying data presentations for business purposes only. It is not designed
for, nor intended for stereo audio reproduction use as might be expected in home theater or
home cinema applications. Any stereo audio input (if provided), is mixed into a common
mono audio output through the projector speaker.
If you wish, you can make use of the projector (mixed mono) speaker in your presentations,
and also connect separate amplified speakers to the Audio Out socket of the projector. The
audio output is a mixed mono signal and controlled by the projector Volume and Mute
settings.
17
If you have a separate sound system, you will most likely want to connect the audio output
of your Video source device to that sound system, instead of to the mono audio projector.
Connecting an HDMI device

You should use an HDMI cable when making connection between the projector and HDMI
devices.
To connect the projector to an HDMI device:
1. Take an HDMI cable and connect one end to the HDMI output port of the video
device.
2. Connect the other end of the cable to the HDMI input port on the projector.
• In the unlikely event that you connect the projector to a DVD player via the projector’s
HDMI input and the projected picture displays wrong colors, please change the color
space to YUV. See "Changing HDMI input settings" on page 25 for details.
• The projector is only capable of playing mixed mono audio, even if a stereo audio input is
connected. See "Connecting audio" on page 17 for details.
• The HDMI input is only available on the PJD5134/PJD5234L/PJD5533w models.
Connecting a Component Video source device

Examine your Video source device to determine if it has a set of unused Component Video
output sockets available:
• If so, you can continue with this procedure.
• If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to a Component Video source device:

1. Take a VGA (D-Sub)-Component adaptor cable and connect the end with 3 RCA type
connectors to the Component Video output sockets of the Video source device. Match
the color of the plugs to the color of the sockets; green to green, blue to blue, and red
to red.
2. Connect the other end of the VGA (D-Sub)-Component adaptor cable (with a D-Sub
type connector) to the COMPUTER IN 1 or COMPUTER IN 2 socket on the
projector.
• If the selected video image is not displayed after the projector is turned on and the correct
video source has been selected, check that the Video source device is turned on and
operating correctly. Also check that the signal cables have been connected correctly.
• VGA-Component adapter
(ViewSonic P/N: CB-00008906)
18
Connecting an S-Video source device
Examine your Video source device to determine if it has an unused S-Video output socket
available:
To connect the projector to an S-Video source device:

1. Take an S-Video cable and connect one end to the S-Video output socket of the Video
source device.
2. Connect the other end of the S-Video cable to the S-VIDEO socket on the projector.
• If you have already made a Component Video connection between the projector and this
S-Video source device using Component Video connections, you need not connect to this
device using an S-Video connection as this makes an unnecessary second connection of
poorer picture quality. See "Connecting Video source devices" on page 17 for details.
Connecting a composite Video source device

Examine your Video source device to determine if it has a set of unused composite Video
output sockets available:
To connect the projector to a composite Video source device:

1. Take a Video cable and connect one end to the composite Video output socket of the
Video source device.
2. Connect the other end of the Video cable to the VIDEO socket on the projector.
• You need only connect to this device using a composite Video connection if Component
Video and S-Video inputs are unavailable for use. See "Connecting Video source devices"
on page 17 for details.
19
Operation
Starting up the projector
1. Plug the power cord into the projector and into a
wall socket. Turn on the wall socket switch
(where fitted).
2. Press II POWER on the projector or remote
control to start the projector. The POWER
indicator light stays blue when the projector is
on.
(If necessary) Rotate the focus ring to adjust the
image clearness.
• If the projector is still hot from previous activity, it will run the cooling fan for
approximately 60 seconds before energizing the lamp.
• To maintain the lamp life, once you turn the projector on, wait at least 5 minutes before
turning it off.
3. If the projector is activated for the first time, select your OSD language following the
on-screen instructions.
4. Switch all of the connected equipment on.
5. The projector will start to search for input signals. The current input signal being
scanned appears in the upper left corner of the screen. If the projector doesn't detect a
valid signal, the message 'No Signal' will continue to be displayed until an input
signal is found.
You can also press SOURCE on the projector or remote control to select your desired
input signal. See "Switching input signal" on page 25 for details.
If the frequency/resolution of the input signal exceeds the projector's operating range, you will
see the message 'Out of Range' displayed on a blank screen. Please change to an input signal
which is compatible with the projector's resolution or set the input signal to a lower setting.
See "Timing chart" on page 61 for details.
20
Using the menus
The projector is equipped with On-Screen Display (OSD) menus for making various
adjustments and settings.
The OSD screenshots below are for reference only, and may differ from the actual design.
Below is the overview of the OSD menu.

Main menu icon
Screen Color Off

Aspect Ratio Auto
Keystone
Highlight Position ENTER
Status
Phase 16
Sub-menu H. Size 0
Zoom
3D Settings Go to the
Color Management previous page
Current input Analog RGB MENU Exit
or to exit.
signal
To use the OSD menus, please set them to your familiar language first.
1. Press MENU/EXIT on the projector or 3. Press to highlight

Menu on the remote control to turn the
OSD menu on. Language and press / to
select a preferred language.
Screen Color Off
Aspect Ratio Auto
Keystone Language English
Position Projector Position Front Table
Phase 16 Auto Power Off Disable
H. Size 0 Blank Timer Disable
Zoom Panel Key Lock Off
Splash Screen ViewSonic
3D Settings Message
Color Management On
Standby Settings
Analog RGB MENU Exit
CEC Off
2. Use / to highlight the SYSTEM 4. Press MENU/EXIT twice* on

the projector or Exit on the
SETTING: BASIC menu.
remote control to leave and
save the settings.
Language English
Projector Position
Auto Power Off
Front Table
Disable
*The first press leads you back
Blank Timer
Panel Key Lock
Disable
Off
to the main menu and the
Splash Screen
Message
ViewSonic second press closes the OSD
On
Standby Settings menu.
CEC Off
: DISPLAY : SYSTEM SETTING: BASIC
: PICTURE : SYSTEM SETTING: ADVANCED
: SOURCE : INFORMATION
21
Utilizing the password function
For security purposes and to help prevent unauthorized use, the projector includes an option
for setting up password security. The password can be set through the On-Screen Display
(OSD) menu. For details of the OSD menu operation, please refer to "Using the menus" on
page 21.
You will be inconvenienced if you activate the password functionality and subsequently forget
the password. Print this user manual (if necessary) and write the password you used in this
manual, and keep it in a safe place for later use.
Setting a password
1. Open the OSD menu and go to the SYSTEM SETTING: ADVANCED > Security
Settings menu. Press MODE/ENTER on the projector or Enter on the remote
control. The Security Settings page is displayed.
2. Highlight Power On Lock and select On by pressing / .
3. As pictured to the right, the four arrow keys INPUT PASSWORD
( , , , ) respectively represent 4 digits
(1, 2, 3, 4). According to the password you desire
to set, press the arrow keys to enter six digits for
the password.
4. Confirm the new password by re-entering the MENU Back
new password.
Once the password is set, the OSD menu returns to the Security Settings page.
5. To leave the OSD menu, press MENU/EXIT on the projector or Exit on the remote
control.
• Once a password has been set, the projector cannot be used unless the correct password
is entered every time the projector is started.
• The digits being input will be displayed as asterisks on-screen. Write your selected
password down here in this user manual in advance or right after the password is entered
so that it is available to you should you ever forget it.
Password: __ __ __ __ __ __
Keep this user manual in a safe place.
If you forget the password

If the password function is activated, you will be asked
to enter the six-digit password every time you turn on Password Error
the projector. If you enter the wrong password, the
password error message as pictured to the right is Please try again.
displayed lasting for three seconds, and the message

'INPUT PASSWORD' follows. You can retry by
entering another six-digit password, or if you did not record the password in this user
manual, and you absolutely do not remember it, you can use the password recall procedure.
See "Entering the password recall procedure" on page 23 for details.
If you enter an incorrect password 5 times in succession, the projector will automatically
shut down in a short time.
22
Entering the password recall procedure
1. Press and hold AUTO on the projector or Auto RECALL PASSWORD
Sync on the remote control for 3 seconds. The Please write down the recall code,
projector will display a coded number on the and contact ViewSonic
Customer Center.
screen.
Recall code:
2. Write down the number and turn off your
projector. 0212
MENU Exit
3. Seek help from the local service center to decode
the number. You may be required to provide
proof of purchase documentation to verify that you are an authorized user of the
projector.
Changing the password

1. Open the OSD menu and go to the SYSTEM SETTING: ADVANCED > Security
Settings > Change Password menu.
2. Press MODE/ENTER on the projector or Enter on the remote control. The message
'INPUT CURRENT PASSWORD' is displayed.
3. Enter the old password.
• If the password is correct, another message 'INPUT NEW PASSWORD' is
displayed.
• If the password is incorrect, the password error message is displayed lasting for
three seconds, and the message 'INPUT CURRENT PASSWORD' is
displayed for your retry. You can press MENU/EXIT on the projector or Exit
on the remote control to cancel the change or try another password.
4. Enter a new password.
5. Confirm the new password by re-entering the new password.
6. You have successfully assigned a new password to the projector. Remember to enter
the new password next time the projector is started.
7. To leave the OSD menu, press MENU/EXIT on the projector or Exit on the remote
control.
The digits being input will be displayed as asterisks on-screen. Write your selected password
down here in this user manual in advance or right after the password is entered so that it is
available to you should you ever forget it.
Password: __ __ __ __ __ __
Keep this user manual in a safe place.
23
Disabling the password function
To disable password protection, go back to the SYSTEM SETTING: ADVANCED >
Security Settings > Power On Lock menu after opening the OSD menu system. Select Off
by pressing / . The message 'INPUT PASSWORD' is displayed. Enter the current
password.
• If the password is correct, the OSD menu returns to the Security Settings page
with 'Off' shown in the row of Power On Lock. You will not have to enter the
password next time you turn on the projector.
• If the password is incorrect, the password error message is displayed lasting for
three seconds, and the message 'INPUT PASSWORD' is displayed for your
retry. You can press MENU/EXIT on the projector or Exit on the remote
control to cancel the change or try another password.
Though the password function is disabled, you need to keep the old password in hand should
you ever need to re-activate the password function by entering the old password.
24
Switching input signal
The projector can be connected to multiple devices at the same time. However, it can only
display one full screen at a time.
Be sure the Quick Auto Search function in the SOURCE menu is On if you want the
projector to automatically search for the signals.
You can also manually select the desired signal by PJD5132/PJD5232L
pressing one of the source selection keys on the
remote control, or cycle through the available input
D-Sub / Comp. 1
signals.
1. Press SOURCE on the projector or remote
control. A source selection bar is displayed. D-Sub / Comp. 2
2. Press / until your desired signal is

selected and press MODE/ENTER on the Video
projector or Enter on the remote control.
Once detected, the selected source information S-Video
will be displayed on the screen for seconds. If
there are multiple devices connected to the
projector, repeat steps 1-2 to search for another PJD5134/PJD5234L/PJD5533w
signal.
• The brightness level of the projected image will D-Sub / Comp. 1
change accordingly when you switch between
different input signals. Data (graphic) "PC"
presentations using mostly static images are D-Sub / Comp. 2
generally brighter than "Video" using mostly
moving images (movies).
• The input signal type effects the options available HDMI
for the Color Mode. See "Selecting a picture
mode" on page 31 for details.
Video
• Please see "Projector specifications" on page 58
for the native display resolution of this projector.
For best display picture results, you should select
and use an input signal which outputs at this S-Video
resolution. Any other resolutions will be scaled by
the projector depending upon the 'aspect ratio'
setting, which may cause some image distortion
or loss of picture clarity. See "Selecting the aspect
ratio" on page 28 for details.
Changing HDMI input settings

This function is only available for the PJD5134/PJD5234L/PJD5533w series.
In the unlikely event that you connect the projector to a device (like a DVD or Blu-ray
player) via the projector’s HDMI input and the projected picture displays wrong colors,
please change the color space to an appropriate one that fits the color space setting of the
output device.
To do this:
1. Open the OSD menu and go to the SOURCE menu.
2. Press to highlight HDMI Format and press / to select a suitable color space
according to the color space setting of the output device connected.
• RGB: Sets the color space as RGB.
25
• YUV: Sets the color space as YUV.
• Auto: Sets the projector to detect the color space setting of input signal
automatically.
3. Press to highlight HDMI Range and press / to select a suitable HDMI color
range according to the color range setting of the output device connected.
• Enhanced: Sets the HDMI color range as 0 - 255.
• Normal: Sets the HDMI color range as 15 - 235.
• This function is only available when the HDMI input port is in use.
• Refer to the documentation of the device for information on the color space setting.
Adjusting the projected image

Adjusting the projection angle
The projector is equipped with an adjuster foot. It
changes the image height and vertical projection
angle. Screw the adjuster foot to fine tune the
angle until the image is positioned where you
want it.
If the projector is not placed on a flat surface or
the screen and the projector are not perpendicular
to each other, the projected image becomes
trapezoidal. To correct this situation, see
"Correcting keystone" on page 27 for details.
Do not look into the lens while the lamp is on. The strong light from the lamp may cause
damage to your eyes.
Auto-adjusting the image

In some cases, you may need to optimize the picture quality. To do this, press AUTO on the
projector or Auto Sync on the remote control. Within 3 seconds, the built-in Intelligent
Auto Adjustment function will re-adjust the values of Frequency and Clock to provide the
best picture quality.
The current source information will be displayed in the upper left corner of the screen for 3
seconds.
• The screen will be blank while AUTO is functioning.
• This function is only available when PC signal (analog RGB) is selected.
Fine-tuning the image clarity

1. Adjust the projected image to the size 2. If necessary, sharpen the image by
that you need using the zoom ring. rotating the focus ring.
26
Correcting keystone
Keystoning refers to the situation where the projected image is noticeably wider at either the
top or bottom. It occurs when the projector is not perpendicular to the screen.
To correct this, besides adjusting the height of the projector, you will need to manually
correct it following one of these steps.
• Using the remote control
Press / on the projector or remote control to
display the Keystone correction page. Press to
correct keystoning at the top of the image. Press
to correct keystoning at the bottom of the image.
Press / Press /
• Using the OSD menu
1. Press MENU/EXIT on the projector or Menu on the remote control and then press
/ until the DISPLAY menu is highlighted.
2. Press to highlight Keystone and press MODE/ENTER on the projector or Enter
on the remote control. The Keystone correction page is displayed.
3. Press to correct keystoning at the top of the image or press to correct
keystoning at the bottom of the image.
Magnifying and searching for details

If you need to find the details on the projected picture, magnify the picture. Use the
direction arrow keys for navigating the picture.
1. Press Magnify on the remote control to display the Zoom bar.
2. Press repeatedly to magnify the picture to a desired size.
3. To navigate the picture, press MODE/ENTER on the projector or Enter on the
remote control to switch to the paning mode and press the directional arrows
( , , , ) to navigate the picture.
4. To reduce size of the picture, press MODE/ENTER on the projector or Enter on the
remote control to switch back to the zoom in/out functionality, and press AUTO/Auto
Sync to restore the picture to its original size. You can also press repeatedly until
it is restored to the original size.
2. Press to highlight Zoom and press MODE/ENTER on the projector or Enter on
the remote control. The Zoom bar is displayed.
3. Repeat steps 2-4 in the section of Using the remote control above.
The picture can only be navigated after the picture is magnified. You can further magnify the
picture while searching for details.
27
Selecting the aspect ratio
The 'aspect ratio' is the ratio of the image width to the image height. Most analog TV and
computers are in 4:3 ratio, and digital TV and DVDs are usually in 16:9 ratio.
With the advent of digital signal processing, digital display devices like this projector can
dynamically stretch and scale the image output to a different aspect than that of the image
input signal.
To change the projected image ratio (no matter what aspect the source is):
1. Press Aspect to show the current setting.
2. Press Aspect repeatedly to select an aspect ratio to suit the format of the video signal
and your display requirements.
2. Press to highlight Aspect Ratio.
3. Press / to select an aspect ratio to suit the format of the video signal and your
display requirements.
28
About the aspect ratio
In the pictures below, the black portions are inactive areas and the white portions are active
areas. OSD menus can be displayed on those unused black areas.
1. Auto: Scales an image proportionally to fit the

projector's native resolution in its horizontal
width. This is suitable for the incoming image
which is neither in 4:3 nor 16:9 and you want to 16:10 picture
make most use of the screen without altering the
image's aspect ratio.
15:9 picture
2. 4:3: Scales an image so that it is displayed in the
center of the screen with a 4:3 aspect ratio. This
is most suitable for 4:3 images like computer
monitors, standard definition TV and 4:3 aspect
DVD movies, as it displays them without aspect
alteration. 4:3 picture
3. 16:9: Scales an image so that it is displayed in

the center of the screen with a 16:9 aspect ratio.
This is most suitable for images which are
already in a 16:9 aspect, like high definition TV,
as it displays them without aspect alteration.
16:9 picture
4. 16:10 (PJD5533w only): Scales an image so

that it is displayed in the center of the screen
with a 16:10 aspect ratio. This is most suitable
for images which are already in a 16:10 aspect,
as it displays them without aspect alteration.
16:10 picture
5. Wide (PJD5533w only): Scales a 4:3 aspect

image vertically and horizontally in a non-linear
manner so that it fills the screen with a 16:9
aspect ratio.
4:3 picture
29
6. Anamorphic (PJD5132/PJD5134/PJD5232L/
PJD5234L only): Scales a 16:9 aspect image
vertically and horizontally in a non-linear
manner so that it fills the screen with a 4:3
aspect ratio.
16:9 picture
30
Optimizing the image
Selecting a picture mode
The projector is preset with several predefined picture modes so that you can choose one to
suit your operating environment and input signal picture type.
To select an operation mode that suits your need, you can follow one of the following steps.
• Press MODE/ENTER on the projector or Color Mode on the remote control
repeatedly until your desired mode is selected.
• Go to the PICTURE > Color Mode menu and press / to select a desired mode.
Picture modes for different types of signals

The picture modes available for different types of signals are listed below.
PC input signals: D-Sub / Comp. 1/2 (analog RGB)
1. Brightest mode: Maximizes the brightness of the projected image. This mode is
suitable for environments where extra-high brightness is required, such as using the
projector in well lit rooms.
2. PC mode: Is designed for presentations under daylight environment to match PC and
notebook coloring.
3. ViewMatch mode: Switches between high brightness performance and accurate color
performance.
4. Movie mode: Is appropriate for playing colorful movies, video clips from digital
cameras or DVs through the PC input for best viewing in a blackened (little light)
environment.
5. Dynamic PC mode: Is designed for presentations under daylight environment to
match PC and notebook coloring. In addition, the projector will optimize the image
quality using the dynamic PC function in accordance with the projected contents.
It takes some time to initiate this function. Make sure the projector has been turned on for
more than 4 minutes.
If the projector is resumed by using the Smart Restart feature, this function can be executed
immediately.
6. Dynamic Movie mode: Is appropriate for playing colorful movies, video clips from
digital cameras or DVs through the PC input for best viewing in a blackened (little
light) environment. In addition, the projector will optimize the image quality using the
dynamic Movie function in accordance with the projected contents.
immediately.
7. User 1/User 2 mode: Recalls the settings customized based on the current available
picture modes. See "Setting the User 1/User 2 mode" on page 32 for details.
Video input signals: S-Video, Video, D-Sub / Comp. 1/2 (YPbPr) / HDMI
1. Brightest mode: Optimized for daylight viewing, with living room level ambient
brightness.
2. Gaming mode: Suitable for all types of entertainment media, including gaming and
movies.
3. ViewMatch mode: Switches between high brightness performance and accurate color
performance.
31
4. Movie mode: Is suitable for enjoying dark movies or DVD movies best viewed in a
blackened (little light) home cinema or lounge room environment.
5. Dynamic Movie mode: Is suitable for enjoying dark movies or DVD movies best
viewed in a blackened (little light) home cinema or lounge room environment. In
addition, the projector will optimize the image quality using the dynamic Movie
function in accordance with the projected contents.
immediately.
6. User 1/User 2 mode: Recalls the settings customized based on the current available
picture modes. See "Setting the User 1/User 2 mode" on page 32 for details.
Setting the User 1/User 2 mode

There are two user-definable modes if the current available picture modes are not suitable
for your need. You can use one of the picture modes (except the User 1/User 2) as a starting
point and customize the settings.
1. Press MENU/EXIT on the projector or Menu on the remote control to open the On-
Screen Display (OSD) menu.
2. Go to the PICTURE > Color Mode menu.
3. Press / to select User 1 or User 2.
4. Press to highlight Reference Mode.
This function is only available when User 1 or User 2 mode is selected up in the Color Mode
sub-menu item.
5. Press / to select a picture mode that is closest to your need.

6. Press to select a sub-menu item to be changed and adjust the value with / .
See Fine-tuning the image quality in user modes below for details.
7. When all settings have been done, highlight Save Settings and press MODE/ENTER
on the projector or Enter on the remote control to store the settings.
8. The confirmation message 'Setting Saved' is displayed.
Using Screen Color

In the situation where you are projecting onto a colored surface such as a painted wall which
may not be white, the Screen Color feature can help correct the projected picture’s colors to
prevent possible color difference between the source and projected pictures.
To use this function, go to the DISPLAY > Screen Color menu and press / to select a
color which is closest to the color of the projection surface. There are several precalibrated
colors to choose from: Whiteboard, Greenboard, and Blackboard.
This function is only available when a PC type input signal is selected.
Fine-tuning the image quality in user modes

According to the detected signal type, there are some user-definable functions available
when User 1 or User 2 mode is selected. You can make adjustments to these functions
based on your needs.
When you are done making adjustments, remember to go to the PICTURE > Save Settings
menu and press MODE/ENTER to save your settings.
32
Adjusting Brightness
Highlight the PICTURE > Brightness menu and press / .
The higher the value, the brighter the image. And the
lower the setting, the darker the image. Adjust this
control so the black areas of the image appear just as
black and that detail in the dark areas is visible. +30 +50 +70
Adjusting Contrast
Highlight the PICTURE > Contrast menu and press / .
The higher the value, the greater the contrast. Use this
to set the peak white level after you have previously
adjusted the Brightness setting to suit your selected
input and viewing environment. -30 0 +30
Adjusting Color
Highlight the PICTURE > Color menu and press / .
Lower setting produces less saturated colors. If the setting is too high, colors on the image
will be overpowering, which makes the image unrealistic.
Adjusting Tint
Highlight the PICTURE > Tint menu and press / .
The higher the value, the more reddish the picture becomes. The lower the value, the more
greenish the picture becomes.
Adjusting Sharpness
Highlight the PICTURE > Sharpness menu and press / .
The higher the value, the sharper the picture becomes. The lower the value, the softer the
picture becomes.
Adjusting Brilliant Color
Highlight the PICTURE > Brilliant Color menu and press / .
This feature utilizes a new color-processing algorithm and system level enhancements to
enable higher brightness while providing truer, more vibrant colors in the projected picture.
It enables a greater than 50% brightness increase in mid-tone images, which are common in
video and natural scenes, so the projector reproduces images in realistic and true colors. If
you prefer images with that quality, select On. If you don’t need it, select Off.
When Off is selected, the Color Temperature function is not available.
Selecting a Color Temperature
Highlight the PICTURE > Color Temperature menu and press / .
The options available for color temperature* settings vary according to the signal type
selected.
1. T1: With the highest color temperature, T1 makes the image appear the most bluish
white than other settings.
2. T2: Makes images appear bluish white.
3. T3: Maintains normal colorings for white.
33
4. T4: Makes images appear reddish white.
*About color temperatures:
There are many different shades that are considered to be "white" for various purposes. One
of the common methods of representing white color is known as the “color temperature”. A
white color with a low color temperature appears to be reddish white. A white color with a
high color temperature appears to have more blue in it.
Color Management
Only in permanent installations with controlled lighting levels such as boardrooms, lecture
theaters, or home theaters, should color management be considered. Color management
provides fine color control adjustment to allow for more accurate color reproduction, should
you require it.
If you have purchased a test disc which contains various color test patterns and can be used
to test the color presentation on monitors, TVs, projectors, etc., you can project any image
from the disc on the screen and enter the Color Management menu to make adjustments.
To adjust the settings:
1. Go to the DISPLAY menu and highlight Color Management.
2. Press MODE/ENTER on the projector or Enter on the remote control and the Color
Management page is displayed.
3. Highlight Primary Color and press / to select a color from among Red, Yellow,
Green, Cyan, Blue, or Magenta.
4. Press to highlight Hue and press / to select its range. Increase in the range
will include colors consisted of more proportions of its two adjacent colors.
Please refer to the illustration to the right for
how the colors relate to each other.
For example, if you select Red and set its
range at 0, only pure red in the projected RED
Yellow GREEN
picture will be selected. Increasing its range
will include red close to yellow and red close
to magenta.
Magenta Cyan
5. Press to highlight Saturation and adjust
its values to your preference by pressing /
BLUE
. Every adjustment made will reflect to the
image immediately.
For example, if you select Red and set its
value at 0, only the saturation of pure red will be affected.
Saturation is the amount of that color in a video picture. Lower settings produce less
saturated colors; a setting of “0” removes that color from the image entirely. If the saturation
is too high, that color will be overpowering and unrealistic.
6. Press to highlight Gain and adjust its values to your preference by pressing /
. The contrast level of the primary color you select will be affected. Every
adjustment made will reflect to the image immediately.
7. Repeat steps 3 to 6 for other color adjustments.
8. Make sure you have made all of the desired adjustments.
9. Press MENU/EXIT on the projector or Exit on the remote control to exit and save the
settings.
34
Setting the presentation timer
Presentation timer can indicate the presentation time on the screen to help you achieve
better time management when giving presentations. Follow these steps to utilize this
function:
1. Press Timer on the remote control to access the Presentation Timer menu or go to
the SYSTEM SETTING: ADVANCED > Presentation Timer menu and press
MODE/ENTER to display the Presentation Timer page.
2. Highlight Timer Period and decide the time period by pressing / . The length of
time can be set from 1 to 5 minutes in 1-minute increments and 5 to 240 minutes in 5-
minute increments.
If the timer is already on, the timer will restart whenever the Timer Period is reset.
3. Press to highlight Timer Display and choose if you want the timer to show up on
the screen by pressing / .
Selection Description
Displays the timer on screen throughout the presentation
Always
time.
1 min/2 min/3 min Displays the timer on screen in the last 1/2/3 minute(s).
Never Hides the timer throughout the presentation time.
4. Press to highlight Timer Position and set the timer position by pressing / .
Top-Left Bottom-Left Top-Right Bottom-Right
5. Press to highlight Timer Counting Direction and select your desired counting
direction by pressing / .
Selection Description
Count Up Increases from 0 to the preset time.
Count Down Decreases from the preset time to 0.
6. Press to highlight Sound Reminder and decide if you want to activate sound
reminder by pressing / . If you select On, a double beep sound will be heard at
the last 30 seconds of counting down/up, and a triple beep sound will be produced
when the timer is up.
7. To activate the presentation timer, press and press / to highlight Start
Counting and press MODE/ENTER.
8. A confirmation message displays. Highlight Yes and press MODE/ENTER on the
projector or remote control to confirm. You will see the message “Timer is On”
displaying on the screen. The timer starts counting when the timer is on.
To cancel the timer, perform the following steps:

1. Go to the SYSTEM SETTING: ADVANCED > Presentation Timer menu and
highlight Off. Press MODE/ENTER. A confirmation message displays.
2. Highlight Yes and press MODE/ENTER to confirm. You will see the message
“Timer is Off” displaying on the screen.
35
Hiding the image
In order to draw the audience's full attention to the presenter, you can use on the
projector or Blank on the remote control to hide the screen image. Press any key on the
projector or remote control to restore the image. The word 'BLANK' appears at the lower
right corner of the screen while the image is hidden.
You can set the blank time in the SYSTEM SETTING: BASIC > Blank Timer menu to
let the projector return the image automatically after a period of time when there is no action
taken on the blank screen.
Once Blank is pressed, the projector enters Economic mode automatically.
CAUTION
Do not block the projection lens from projecting as this could cause the blocking object to
become heated and deformed or even cause a fire.
Locking control keys

With the control keys on the projector locked, you can prevent your projector settings from
being changed accidentally (by children, for example). When the Panel Key Lock is on, no
control keys on the projector will operate except I
I
POWER.
1. Press on the projector or Lock on the remote control, or go to the SYSTEM

SETTING: BASIC > Panel Key Lock menu, and select On by pressing / on
the projector or remote control.
2. A confirmation message is displayed. Select Yes to confirm.
To release panel key lock, press and hold on the projector or Lock on the remote
control for 3 seconds.
You can also use the remote control to enter the SYSTEM SETTING: BASIC > Panel
Key Lock menu and press / to select Off.
• Keys on the remote control are still functional when panel key lock is enabled.
• If you press I POWER to turn off the projector without disabling panel key lock, the
I
projector will still be in locked status the next time it is turned on.
Freezing the image

Press Freeze on the remote control to freeze the image. The word 'FREEZE' will be
displayed in the upper left corner of the screen. To release the function, press any key on the
projector or remote control.
Even if an image is frozen on the screen, the pictures are running on the video or other
device. If the connected devices have active audio output, you will still hear the audio even
though the image is frozen on screen.
Operating in a high altitude environment

We recommend you use the High Altitude Mode when your environment is between 1500
m–3000 m above sea level, and temperature is between 0°C–35°C.
CAUTION
Do not use the High Altitude Mode if your altitude is between 0 m and 1500 m and temperature
is between 0°C and 35°C. The projector will be over cooled, if you turn the mode on under
such a condition.
36
To activate the High Altitude Mode:
Notice
1. Press MENU/EXIT on the projector or Menu on
We recommend you use the High Altitude
mode by selecting it whenever your
the remote control and then press / until the environment is higher than 1500 m.
SYSTEM SETTING: ADVANCED menu is

Do you want to turn High Altitude
highlighted. Mode ON?
2. Press to highlight High Altitude Mode and Yes No
press / to select On. A confirmation

message is displayed.
3. Highlight Yes and press MODE/ENTER on the projector or Enter on the remote
control.
Operation under "High Altitude Mode" may cause a higher decibel operating noise level
because of increased fan speed necessary to improve overall system cooling and
performance.
If you use this projector under other extreme conditions excluding the above, it may display
auto shut-down symptoms, which is designed to protect your projector from over-heating.
In cases like this, you should switch to High Altitude Mode to solve these symptoms.
However, this is not to state that this projector can operate under any and all harsh or
extreme conditions.
Using the CEC function

This projector supports CEC (Consumer Electronics Control) function for synchronized
power on/off operation via HDMI connection. That is, if a device that also supports CEC
function is connected to the HDMI input of the projector, when the projector’s power is
turned on or off, the power of the connected device will also be turned on or off
automatically (and vice versa).
To turn on the CEC function:
1. Press MENU/EXIT on the projector or Menu on the remote control to open the On-
Screen Display (OSD) menu.
2. Go to the SYSTEM SETTING: BASIC > CEC menu.
3. Press / to select On.
• In order for the CEC function to work properly, make sure that the device is correctly
connected to the HDMI input of the projector via a HDMI cable, and its CEC function is
turned on.
• Depending on the connected device, the CEC function may not work.
Using the 3D functions

This projector features 3D function which enables you to enjoy 3D movies, videos, and
sporting events in a more realistic way by presenting the depth of the images. You need to
wear a pair of 3D glasses to view 3D images.
If the 3D signal is input from an HDMI 1.4a compatible device, the projector detects the
signal for 3D Sync information and once detected, it projects images in 3D format
automatically. In other cases, you may need to manually select a 3D Sync format for the
projector to project 3D images correctly.
To select a 3D Sync format:
37
2. Press to highlight 3D Settings and press MODE/ENTER on the projector or
Enter on the remote control.
3. Press to highlight 3D Sync and press MODE/ENTER on the projector or Enter
on the remote control.
4. Press to select a 3D Sync setting according to the table below and then press
MODE/ENTER on the projector or Enter on the remote control to confirm.
Input signal type (resolution) Default setting 3D Sync options available
HDMI (PC) and DVI-D 120Hz
signals (SVGA 120Hz, XGA 120Hz, Frame Sequential Off, Frame Sequential
WXGA 120Hz, 1280x720 120Hz)
Off, Frame Sequential,
HDMI (PC) and DVI-D 60Hz signals
Off Frame Packing, Top-
(up to 1920x1200 60Hz)
Bottom, Side-by-Side
Video, S-Video signals (HQFs) and
Component video, HDMI signals Off Off, Frame Sequential
(NTSC 480i)
120Hz:Off, Frame
Component video, HDMI signals Sequential
120Hz: Off
(480p, 720p, 1080p, 1080i) without 60Hz: Off, Frame
60Hz: Off
3D information frame Sequential, Frame Packing,
Top-Bottom, Side-by-Side
Auto, Off, Frame
HDMI 1.4a signals (720p, 1080i,
Auto Sequential, Frame Packing,
1080p) with 3D information frame
Top-Bottom, Side-by-Side
For example, if the signal is input from the projector’s S-Video input socket, and its signal
type (resolution) is 480i, then the default 3D Sync setting of the projector is Off, and the
options you can choose for the 3D Sync setting are Off and Frame Sequential.
When the 3D Sync function is on:
• The brightness level of the projected image will decrease.
• The Color Mode cannot be adjusted.
• The Keystone can only be adjusted within limited degrees.
• The Zoom can only magnify the pictures to limited sizes.
If you discover the inversion of the 3D image depth, set the 3D Sync Invert function to “Invert”
to correct the problem.
Using the projector in standby mode

Some of the projector functions are available in standby mode (plugged in but not turned
on). To use these functions, be sure you have turned on the corresponding menus under
SYSTEM SETTING: BASIC > Standby Settings, and the cable connections are correctly
made. For the connection methods, see the Connection chapter.
Power Saving
Less than 0.5W power consumption when Power Saving mode is turned on.
Active VGA Out
Selecting On outputs a VGA signal when the COMPUTER IN 1 and COMPUTER OUT
sockets are correctly connected to devices. The projector outputs the signal received only
from COMPUTER IN 1.
38
Active Audio Out
Selecting On outputs an audio signal when the AUDIO IN and AUDIO OUT sockets are
correctly connected to devices.
Quick Power Off
Selecting On enables the function and the projector will not enter the cooling process after
being shut down. Selecting Off disables the function and the projector will enter normal
cooling process after being shut down.
• If you attempt to restart the projector right after it’s been turned off, it may not be turned
on successfully and will rerun its cooling procedure.
• When Off is selected, the Smart Restart function will be automatically turned off.
Shutting down the projector

1. Press II POWER and a confirmation message
is displayed prompting you.
If you don't respond in a few seconds, the
message will disappear.
2. Press II POWER a second time.
3. Disconnect the power cord from the wall
socket if the projector will not be used in an
extended period of time.
CAUTION
• To protect the lamp, the projector will not respond to any commands during the cooling
process.
• To shorten the cooling time, you can also activate the Quick Power Off function. See
"Quick Power Off" on page 39 for details.
• Do not unplug the power cord before the projector shutdown sequence is complete.
39
Menu operation
Menu system
Please note that the on-screen display (OSD) menus vary according to the signal type
selected.
The menu items are available when the projector detects at least one valid signal. If there is
no equipment connected to the projector or no signal detected, limited menu items are
accessible.
Main menu Sub-menu Options

Off/Blackboard/Greenboard/
Screen Color
Whiteboard
Auto/4:3/16:9/
16:10 (PJD5533w only)/Wide
Aspect Ratio (PJD5533w only)/Anamorphic
(PJD5132/PJD5134/PJD5232L/
PJD5234L only)
Keystone
Position
1. Phase
DISPLAY H. Size
Zoom
Auto/Off/Frame Sequential/
3D Sync Frame Packing/Top-Bottom/
3D Settings
Side-by-Side
3D Sync Invert Disable/Invert
Primary Color R/G/B/C/M/Y
Color Hue
Management Saturation
Gain
PC source: Brightest/PC/ViewMatch/Movie/Dynamic
PC/Dynamic Movie/User 1/User 2
Color Mode
Video source: Brightest/Gaming/ViewMatch/Movie/
Dynamic Movie/User 1/User 2
PC source: Brightest/PC/ViewMatch/Movie/Dynamic
PC/Dynamic Movie
Reference Mode
Video source: Brightest/Gaming/ViewMatch/Movie/
Dynamic Movie
2.
Brightness
PICTURE
Contrast
Color
Tint
Sharpness
Brilliant Color On/Off
Color Temperature T1/T2/T3/T4
Save Settings
40
Quick Auto Search Off/On
HDMI Format (PJD5134/PJD5234L/
RGB/YUV/Auto
PJD5533w only)
HDMI Range (PJD5134/PJD5234L/
Enhanced/Normal
PJD5533w only)
Disable/5 min/10 min/15 min/
DynamicEco Timer
30 min
3. SOURCE
Smart Restart Off/On
Pattern Off/01/02/03/04/05
Projection (Projector Position)/3D Sync/Lamp Mode/
DCR/Closed Caption/Auto Off (Auto Power Off)/
My Button Message/Screen Color/CEC (PJD5134/PJD5234L/
PJD5533w only)/Auto Search (Quick Auto Search)/
Information
Language Multi-language OSD selection
Front Table/Rear Table/Rear
Projector Position
Ceiling/Front Ceiling
Auto Power Off
30 min/40 min/50 min/60 min
Blank Timer
20 min/25 min/30 min
Timer Off/30 min/1 hour/2 hours/3
4. Sleep Timer hours/4 hours/8 hours/12
SYSTEM hours
SETTING: Panel Key Lock On/Off
BASIC Splash Screen Black/Blue/ViewSonic/Off
Message On/Off
Power Saving On/Off
Active VGA Out On/Off
Standby Settings
Active Audio Out On/Off
Quick Power Off On/Off
CEC (PJD5134/PJD5234L/PJD5533w
On/Off
only)
41
High Altitude Mode On/Off
DCR On/Off
Mute On/Off
Audio Settings
Volume
5 sec/10 sec/15 sec/20
Menu Display Time
sec/25 sec/30 sec
Menu Settings Center/Top-Left/Top-
Menu Position Right/Bottom-Left/
Bottom-Right
Closed Caption Enable On/Off
Closed Caption
Caption Version CC1/CC2/CC3/CC4
Lamp Mode Normal/Economic
5. Lamp Settings Reset Lamp Timer
SYSTEM Equivalent Lamp Hour
SETTING: Timer Period 1~240 minutes
ADVANCED Timer Display
Always/1 min/2 min/3 min/
Never
Top-Left/Bottom-Left/Top-
Timer Position
Presentation Timer Right/Bottom-Right
Timer Counting
Count Down/Count Up
Direction
Sound Reminder On/Off
Start Counting/Off
Change Password
Security Settings
Power On Lock On/Off
Remote Control Code A/B
Reset All Settings
Reset Settings
Reset Color Settings
42
• Source
• Color Mode
6.
Current System Status • Resolution
INFORMATION
• Color System
• Equivalent Lamp Hour
43
Description of each menu
Function Description
Corrects the projected picture’s color when the projection surface is
Screen Color not white. See "Using Screen Color" on page 32 for details.
There are three options to set the image's aspect ratio depending on
Aspect Ratio your input signal source. See "Selecting the aspect ratio" on page 28
for details.
Corrects any keystoning of the image. See "Correcting keystone" on
Keystone page 27 for details.
Displays the position adjustment page. To move the projected image,
use the directional arrow keys. The values shown on the lower
Position
1. DISPLAY menu
position of the page change with every key press you made until they
reach their maximum or minimum.
Adjusts the clock phase to reduce image
distortion.
Phase
H. Size Adjusts the horizontal width of the image.

Magnifies or reduces the projected image. See "Magnifying and
Zoom searching for details" on page 27 for details.
3D Settings See "Using the 3D functions" on page 37 for details.
Color
See "Color Management" on page 34 for details.
Management
44
Pre-defined picture modes are provided so you can optimize your
Color Mode projector image set-up to suit your program type. See "Selecting a
picture mode" on page 31 for details.
Selects a picture mode that most suits your need for the image quality
Reference and further fine-tune the image based on the selections listed on the
Mode same page below. See "Setting the User 1/User 2 mode" on page 32
for details.
Adjusts the brightness of the image. See "Adjusting Brightness" on
Brightness page 33 for details.
Adjusts the degree of difference between dark and light in the image.
2. PICTURE menu
Contrast See "Adjusting Contrast" on page 33 for details.

Adjusts the color saturation level -- the amount of each color in a
Color video image. See "Adjusting Color" on page 33 for details.
Adjusts the red and green color tones of the image. See "Adjusting
Tint" on page 33 for details.
Tint
The function is only available when Video or S-Video with NTSC
system is selected.
Adjusts the image to make it look sharper or softer. See "Adjusting
Sharpness Sharpness" on page 33 for details.
Adjusts white peaking while maintaining correct color presentation.
Brilliant Color See "Adjusting Brilliant Color" on page 33 for details.
Color
See "Selecting a Color Temperature" on page 33 for details.
Temperature
Save Settings Saves the settings made for the User 1 or User 2 mode.
45
Quick Auto
See "Switching input signal" on page 25 for details.
Search
HDMI Format
See "Changing HDMI input settings" on page 25 for details.
HDMI Range
Allows the projector to decrease the power consumption automatically
DynamicEco if no input signal is detected after a set period of time.
Timer It takes some time to initiate this function. Make sure the
3. SOURCE menu
projector has been turned on for more than 4 minutes.

Selecting On enables you to restart the projector immediately within
150 seconds after turning it off. After 150 seconds, if the projector is
not turned on again, it will directly enter the standby mode.
Smart •It takes some time to initiate this function. Make sure the
Restart projector has been turned on for more than 4 minutes.
If the projector is resumed by using the Smart Restart feature,
this function can be executed immediately.
•When On is selected, the Quick Power Off function will be
automatically set to “On”.
The projector can display several test patterns. It helps you adjust the
image size and focus and check that the projected image is free from
Pattern distortion.
Selecting User displays the picture you saved as Screen Capture.
My Button Sets a hotkey on remote control.
46
Sets the language for the On-Screen Display (OSD) menus. See
Language "Using the menus" on page 21 for details.
Projector The projector can be installed on a ceiling or behind a screen, or with
one or more mirrors. See "Choosing a location" on page 12 for
Position details.
Auto Power Allows the projector to turn off automatically if no input signal is
detected after a set period of time. See "Setting Auto Power Off" on
Off
4. SYSTEM SETTING: BASIC menu

Blank Timer
Sets the image blank time when the Blank feature is activated, once
elapsed the image will return to the screen. See "Hiding the image"
Timer on page 36 for details.
Sleep Timer
Allows the projector to turn off automatically after a set period of
time if the incoming signal is present or not.
Panel Key Disables or enables all panel key functions except II POWER on the
Lock projector and keys on the remote control. See "Locking control keys"
on page 36 for details.
Allows you to select which logo screen will be displayed during
Splash Screen projector start-up.
Selecting On displays the current information on the screen when the
Message projector is detecting or searching for a signal.
Standby
See "Using the projector in standby mode" on page 38 for details.
Settings
CEC See "Using the CEC function" on page 37 for details.
47
High Altitude A mode for operation in high altitude areas. See "Operating in a high
altitude environment" on page 36 for details.
Mode
Enables or disables the DCR (Dynamic Contrast Ratio) function.
Selecting On enables the function and the projector will
automatically switch the lamp mode between normal and economic
modes according to the input image detected.
DCR
This function is only available when a PC source is in use.
After enabling DCR, frequent lamp mode switching may shorten

lamp life and noise level will vary during operation.
The sound adjustments made as below will have an effect on the
projector speaker. Be sure you have made a correct connection to the
projector audio input/output jacks. See "Connection" on page 15 for
more details.
Audio Settings Mute
5. SYSTEM SETTING: ADVANCED menu
Mutes the sound received from AUDIO IN.

Volume
Adjusts the sound level received from AUDIO IN.
Menu Display Time
Sets the length of time the OSD will remain active after your last key
Menu Settings press. The range is from 5 to 30 seconds in 5-second increments.
Menu Position
Sets the On-Screen Display (OSD) menu position.
Closed Caption Enable
Activates the function by selecting On when the selected input signal
carries closed captions.
• Captions: An on-screen display of the dialogue, narration, and
sound effects of TV programs and videos that are closed
Closed captioned (usually marked as "CC" in TV listings).
Caption This function is only available when a Composite video or S-
Video input signal is selected and its system format is NTSC.
Caption Version
Selects a preferred closed captioning mode. To view captions, select
CC1, CC2, CC3, or CC4 (CC1 displays captions in the primary
language in your area).
Lamp Mode
See "Setting Lamp Mode as Economic" on page 51 for details.
Reset Lamp Timer
Lamp Settings See "Resetting the lamp timer" on page 55 for details.
Equivalent Lamp Hour
See "Getting to know the lamp hour" on page 51 for details on how
the total lamp hour is calculated.
48
Presentation Reminds the presenter to finish the presentation within a certain time
Timer frame. See "Setting the presentation timer" on page 35 for details.
5. SYSTEM SETTING: ADVANCED menu
Security
See "Utilizing the password function" on page 22 for details.
Settings
Remote
See "Remote control code" on page 9 for details.
Control Code
Reset All Settings
Returns all settings to the factory preset values.
The following settings will still remain: Keystone, Language,
Projector Position, High Altitude Mode, Security Settings,
Remote Control Code.
Reset Settings
Reset Color Settings
Returns all color settings to the factory preset values.
Source
Shows the current signal source.
6. INFORMATION menu
Color Mode
Shows the selected mode in the PICTURE menu.
Current Resolution
System Status Shows the native resolution of the input signal.
Color System
Shows input system format, NTSC, PAL, SECAM, or RGB.
Equivalent Lamp Hour
Displays the number of hours the lamp has been used.
49
Maintenance
Care of the projector
Your projector needs little maintenance. The only thing you need to do on a regular basis is
to keep the lens clean.
Never remove any parts of the projector except the lamp. Contact your dealer if other parts
need replacing.
Cleaning the lens

Clean the lens whenever you notice dirt or dust on the surface.
• Use a canister of compressed air to remove dust.
• If there is dirt or smears, use lens-cleaning paper or moisten a soft cloth with lens
cleaner and gently wipe the lens surface.
CAUTION
Never rub the lens with abrasive materials.
Cleaning the projector case

Before you clean the case, turn the projector off using the proper shutdown procedure as
described in "Shutting down the projector" on page 39 and unplug the power cord.
• To remove dirt or dust, wipe the case with a soft, lint-free cloth.
• To remove stubborn dirt or stains, moisten a soft cloth with water and a neutral pH
detergent. Then wipe the case.
CAUTION
Never use wax, alcohol, benzene, thinner or other chemical detergents. These can damage the
case.
Storing the projector

If you need to store the projector for an extended time, please follow the instructions below:
• Make sure the temperature and humidity of the storage area are within the
recommended range for the projector. Please refer to "Specifications" on page 58 or
consult your dealer about the range.
• Retract the adjuster feet.
• Remove the battery from the remote control.
• Pack the projector in its original packing or equivalent.
Transporting the projector

It is recommended that you ship the projector with its original packing or equivalent.
50
Lamp information
Getting to know the lamp hour
When the projector is in operation, the duration (in hours) of lamp usage is automatically
calculated by the built-in timer.
To obtain the lamp hour information:
/ until the SYSTEM SETTING: ADVANCED menu is highlighted.
2. Press to highlight Lamp Settings and press MODE/ENTER on the projector or
ENTER on the remote control. The Lamp Settings page is displayed.
3. You will see the Equivalent lamp hour information on the menu.
4. To leave the menu, press MENU/EXIT on the projector or Exit on the remote
control.
You can also get the lamp hour information on the INFORMATION menu.
Extending lamp life

The projection lamp is a consumable item. To keep the lamp life as long as possible, you
can do the following settings via the OSD menu.
Setting Lamp Mode as Economic
Using Economic mode reduces system noise and power consumption by 20%. If the
Economic mode is selected, the light output will be reduced and result in darker projected
pictures.
Setting the projector in Economic mode also extends the lamp operation life. To set
Economic mode, go into the SYSTEM SETTING: ADVANCED > Lamp Settings >
Lamp Mode menu and press / .
Setting Auto Power Off

This function allows the projector to turn off automatically if no input source is detected
after a set period of time to prevent unnecessary waste of lamp life.
To set Auto Power Off, go into the SYSTEM SETTING: BASIC > Auto Power Off
menu and press / . If the preset time lengths are not suitable for your presentation,
select Disable. The projector will not automatically shut down in a certain time period.
51
Timing of replacing the lamp
When the LAMP indicator light lights up red or a message appears suggesting it is time to
replace the lamp, please install a new lamp or consult your dealer. An old lamp may cause a
malfunction in the projector and in some instances the lamp may explode.
CAUTION
The LAMP indicator light and TEMPerature indicator light will light up if the lamp becomes too
hot. Turn the power off and let the projector cool for 45 minutes. If the LAMP or TEMP indicator
still lights up after turning the power back on, please contact your dealer. See "Indicators" on
The following lamp warning displays will remind you to change the lamp.
Status Message
Install a new lamp for optimal performance. If the Notice
projector is normally run with Economic selected
(See "Setting Lamp Mode as Economic" on page Order Replacement Lamp
51), you may continue to operate the projector Lamp > ____ Hours
until the next hour lamp warning appears.
OK
A new lamp should be fitted to avoid the Notice

inconvenience when the projector runs out of lamp
time. Replace Lamp Soon
Lamp > ____ Hours
OK
It is strongly recommended that you replace the Notice

lamp at this age. The lamp is a consumable item.
The lamp brightness diminishes with use. This is Replace Lamp Now
normal lamp behavior. You can replace the lamp Lamp > ____ Hours
whenever you notice that the brightness level has Lamp usage time exceeded
significantly diminished. If the lamp is not OK

replaced beforehand, it must be replaced when
you see this message.
The lamp MUST be replaced before the projector Notice
will operate normally.
Lamp usage time exceeded
Replace lamp (refer to User Manual)
Then reset lamp timer
OK
52
Replacing the lamp
To prepare a new lamp, contact your dealer and tell the lamp type number.
Type number: RLC-078 (PJD5132/PJD5232L/PJD5134/PJD5234L)
Type number: RLC-085 (PJD5533w)
WARNING
Hg - Lamp contains mercury. Manage in accordance with local disposal

laws. See www.lamprecycle.org
• Be careful of broken glass when replacing the lamp.
• Please wear eye protection and gloves when performing overhead installation.
• To reduce the risk of electrical shock, always turn the projector off and disconnect the
power cord before changing the lamp.
• To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes
before replacing the lamp.
• To reduce the risk of injuries to fingers and damage to internal components, use caution
when removing lamp glass that has shattered into sharp pieces. Before replacing the
lamp, clean the lamp compartment and dispose of cleaning materials. Be careful of sharp
edges in the lamp compartment. Wash hands after lamp replacement.
• Only ViewSonic certified lamps are tested with this projector. Use of other lamps may
cause electrical shock and fire.
1. Turn the power off and disconnect the

projector from the wall socket. If the lamp
is hot, avoid burns by waiting for
approximately 45 minutes until the lamp
has cooled.
2. Loosen the screws that secure the lamp
cover on the both sides of the projector until
the lamp cover loosens.
3. Remove the lamp cover from the projector.

WARNING
• Do not turn the power on with the lamp cover
removed.
• Do not insert your fingers between the lamp

and the projector. The sharp edges inside the
projector may cause injuries.
Remove and dispose of the lamp protection film.
53
4. Loosen the screw that secures the lamp.
5. Disconnect the lamp’s wire connector from

the projector, and then lift the handle so that
it stands up. Use the handle to slowly pull
the lamp out of the projector. 2
1 3
CAUTION
• Pulling it too quickly may cause the lamp to
break and scatter broken glass in the projector.
• Do not place the lamp in locations where water

might splash on it, children can reach it, or
near flammable materials.
• Do not insert your hands into the projector

after the lamp is removed. If you touch the
optical components inside, it could cause color
unevenness and distortion of the projected
images.
6. Insert the new lamp into the lamp
compartment and make sure it fits in the
projector. Connect the new lamp’s wire
connector to the projector.
7. Tighten the screw that secures the lamp.

CAUTION
• Loose screw may cause a bad connection,
which could result in malfunction.
• Do not over tighten the screw.
8. Ensure the handle is fully laid flat and

locked in place.
54
9. Place the lamp protection film supplied
with the new lamp on the lamp
compartment.
10. Replace the lamp cover on the projector.
11. Tighten the screws that secure the lamp

cover.
CAUTION
• Loose screw may cause a bad connection,
which could result in malfunction.
• Do not over tighten the screws.
12. Restart the projector.

CAUTION
Do not turn the power on with the lamp cover removed.
Resetting the lamp timer

13. After the startup logo, open the On-Screen Notice
Display (OSD) menu.
14. Go to the SYSTEM SETTING: Reset Lamp Timer
ADVANCED > Lamp Settings menu. Press Reset Cancel
MODE/ENTER on the projector or ENTER

on the remote control. The Lamp Settings
page is displayed.
15. Press to highlight Reset lamp timer and
press MODE/ENTER on the projector or
ENTER on the remote control. A warning
message is displayed asking if you want to
reset the lamp timer.
16. Highlight Reset and press MODE/ENTER
on the projector or ENTER on the remote
control. The lamp time will be reset to '0'.
CAUTION
Do not reset if the lamp is not new or replaced as this
could cause damage.
55
Indicators
Light Status & Description
POWER TEMP LAMP
Power events
Blue
Off Off Stand-by mode
Flashing
Blue Off Off Powering up
Blue Off Off Normal operation
Lamp events
Purple The projector has shut down automatically. If you try
Off Red to re-start the projector, it will shut down again.
Flashing
Please contact your dealer for assistance.
1. The projector needs 60 seconds to cool down.
Off Off Red Or
2. Please contact your dealer for assistance.
Thermal events
Off Red Off
Off Red Red
Off Red Green
Red Red Red
Red Red Green The projector has shut down automatically. If you try
to re-start the projector, it will shut down again.
Blue Red Red Please contact your dealer for assistance.
Blue Red Green
Purple Red Red
Purple Red Green
Off Green Red
56
Troubleshooting
The projector does not turn on.
Cause Remedy
Plug the power cord into the AC inlet on the
There is no power from the power projector, and plug the power cord into the
cord. power outlet. If the power outlet has a switch,
make sure that it is switched on.
Attempting to turn the projector on Wait until the cooling down process has
again during the cooling process. completed.
No picture
Cause Remedy
The video source is not turned on or Turn the video source on and check that the
connected correctly. signal cable is connected correctly.
The projector is not correctly
Check the connection.
connected to the input signal device.
Select the correct input signal with the
The input signal has not been
SOURCE key on the projector or remote
correctly selected.
control.
Blurred image
Cause Remedy
The projection lens is not correctly Adjust the focus of the lens using the focus
focused. ring.
The projector and the screen are not Adjust the projection angle and direction as
aligned properly. well as the height of the projector if necessary.
Remote control does not work

Cause Remedy
The battery is out of power. Replace the battery with a new one.
There is an obstacle between the
Remove the obstacle.
remote control and the projector.
You are too far away from the Stand within 8 meters (26 feet) of the
projector. projector.
57
Specifications
Projector specifications
• All specifications are subject to change without notice.
• Not all models can be purchased in your region.
General
Product name DLP Projector
Optical
Resolution PJD5132/PJD5134:
800 x 600 SVGA
PJD5232L/PJD5234L:
1024 x 768 XGA
PJD5533w:
1280 x 800 WXGA
Display system 1-CHIP DMD
Lamp 190 W lamp
Electrical
Power supply AC100–240V, 50/60 Hz (Automatic)
Power consumption 250 W (Max); < 0.5 W (Standby)
Mechanical
Weight 2.1 Kg (4.63 lbs)
Input terminal
Computer input
RGB input D-Sub 15-pin (female) x 2
Video signal input
S-VIDEO Mini DIN 4-pin port x 1
VIDEO RCA jack x 1
SD/HDTV signal input
Analog – D-Sub <–> Component RCA jack x 3
(through RGB input)
Digital – PJD5132/PJD5232L:
N/A
PJD5134/PJD5234L/PJD5533w:
HDMI V1.4a x 1
Audio signal input PC audio jack x 1
58
Output terminal
RGB output D-Sub 15-pin (female) x 1
Audio signal output PC audio jack x 1
Speaker 2 watt x 1
Control terminal
RS-232 serial control 9 pin x 1
LAN N/A
USB serial control Type mini B
IR receiver x 1 (Front)
Environmental Requirements
Operating temperature 0°C–40°C at sea level
Operating relative 10%–90% (without condensation)
humidity
Operating altitude • 0–1499 m at 5°C–35°C
• 1500–3000 m at 5°C–25°C (with High Altitude Mode on)
59
Dimensions
268 mm (W) x 84.4 mm (H) x 221 mm (D) (Excluding extrusions)
268
221
MENU
EXIT
84.4
Ceiling mount installation

Ceiling mount screws:
110.05 M4 x 8 (Max. L = 8 mm)
55
81.5
81.5
Unit: mm
60
Timing chart
Supported timing for PC input
Horizontal Vertical
Pixel Frequency
Resolution Frequency Frequency Mode
(MHz)
(kHz) (Hz)
720 x 400 31.469 70.087 28.3221 720 x 400_70
31.469 59.94 25.175 VGA_60
37.861 72.809 31.5 VGA_72
640 x 480 37.5 75 31.5 VGA_75
43.269 85.008 36 VGA_85
61.91 119.518 52.5 VGA_120
35.156 56.250 36 SVGA_56
37.879 60.317 40 SVGA_60
48.077 72.188 50 SVGA_72
800 x 600 46.875 75 49.5 SVGA_75
53.674 85.061 56.25 SVGA_85
30.99 49.916 30.75 SVGA_50
77.425 119.854 83 SVGA_120
48.363 60.004 65 XGA_60
56.476 70.069 75 XGA_70
60.023 75.029 78.75 XGA_75
1024 x 768
68.667 84.997 94.5 XGA_85
39.634 49.98 52 XGA_50
98.958 119.804 137.75 XGA_120
49.702 59.81 83.5 WXGA_60
1280 x 800 62.795 74.934 106.5 WXGA_75
71.554 84.88 122.5 WXGA_85
63.981 60.02 108.000 SXGA_60
1280 x 1024 79.976 75.025 135.000 SXGA_75
91.146 85.024 157.500 SXGA_85
1280 x 960 60 60 108 1280 x 960_60
1400 x 1050 65.317 59.978 121.75 SXGA+_60
1600 x 1200 75 60 162 UXGA
640 x 480@67Hz 35 66.667 30.24 MAC13
832 x 624@75Hz 49.722 74.546 57.28 MAC16
1152 x 870@75Hz 68.68 75.06 100 MAC21
61
Supported timing for Component-YPbPr input
Horizontal Frequency
Signal Format Vertical Frequency (Hz)
(kHz)
480i(525i)@60Hz 15.73 59.94
480p(525p)@60Hz 31.47 59.94
576i(625i)@50Hz 15.63 50.00
576p(625p)@50Hz 31.25 50.00
720p(750p)@60Hz 45.00 60.00
720p(750p)@50Hz 37.50 50.00
1080i(1125i)@60Hz 33.75 60.00
1080i(1125i)@50Hz 28.13 50.00
1080P@60Hz 67.5 60
1080P@50Hz 56.25 50
Displaying a 1080i(1125i)@60Hz or 1080i(1125i)@50Hz signal may result in slight image
vibration.
Supported timing for Video and S-Video inputs

Horizontal Vertical Frequency Color sub-carrier
Video mode
Frequency (kHz) (Hz) Frequency (MHz)
NTSC 15.73 60 3.58
PAL 15.63 50 4.43
SECAM 15.63 50 4.25 or 4.41
PAL-M 15.73 60 3.58
PAL-N 15.63 50 3.58
PAL-60 15.73 60 4.43
NTSC4.43 15.73 60 4.43
62
Copyright information
Copyright
Copyright 2012. All rights reserved. No part of this publication may be reproduced,
transmitted, transcribed, stored in a retrieval system or translated into any language or
computer language, in any form or by any means, electronic, mechanical, magnetic, optical,
chemical, manual or otherwise, without the prior written permission of ViewSonic
Corporation.
Disclaimer
ViewSonic Corporation makes no representations or warranties, either expressed or
implied, with respect to the contents hereof and specifically disclaims any warranties,
merchantability or fitness for any particular purpose. Further, ViewSonic Corporation
reserves the right to revise this publication and to make changes from time to time in the
contents hereof without obligation to notify any person of such revision or changes.
*DLP and Digital Micromirror Device (DMD) are trademarks of Texas Instruments. Others
are copyrights of their respective companies or organizations.
63
Appendix
IR control table
Code A
Key Format Byte1 Byte2 Byte3 Byte4
Power NEC 83 F4 17 E8
Auto Sync NEC 83 F4 08 F7
VGA NEC 83 F4 41 BE
Video NEC 83 F4 52 AD
Source NEC 83 F4 04 FB
Color Mode NEC 83 F4 10 EF
Up / KeyS + NEC 83 F4 0B F4
Left NEC 83 F4 0E F1
Enter NEC 83 F4 15 EA
Right NEC 83 F4 0F F0
Down / KeyS - NEC 83 F4 0C F3
Menu NEC 83 F4 30 CF
My Button NEC 83 F4 56 A9
Exit NEC 83 F4 28 D7
Mouse L key NEC 83 F4 36 C9
Mouse R key NEC 83 F4 37 C8
PgUp NEC 83 F4 05 FA
PgDn NEC 83 F4 06 F9
Mouse NEC 83 F4 31 CE
Magnify NEC 83 F4 32 CD
Volume + NEC 83 F4 82 7D
Volume - NEC 83 F4 83 7C
Panel Key Lock NEC 83 F4 57 A8
Freeze NEC 83 F4 03 FC
Pattern NEC 83 F4 55 AA
Blank NEC 83 F4 07 F8
Mute NEC 83 F4 14 EB
DynamicEco™ NEC 83 F4 2B D4
Timer NEC 83 F4 27 D8
Aspect NEC 83 F4 13 EC
64
Code B
Key Format Byte1 Byte2 Byte3 Byte4
Power NEC 83 F4 60 9F
Auto Sync NEC 83 F4 63 9C
VGA NEC 83 F4 64 9B
Video NEC 83 F4 66 99
Source NEC 83 F4 7D 82
Color Mode NEC 83 F4 9E 61
Up / KeyS + NEC 83 F4 67 98
Left NEC 83 F4 69 96
Enter NEC 83 F4 6B 94
Right NEC 83 F4 6A 95
Down / KeyS - NEC 83 F4 68 97
Menu NEC 83 F4 6C 93
My Button NEC 83 F4 6D 92
Exit NEC 83 F4 6E 91
Mouse L key NEC 83 F4 38 C7
Mouse R key NEC 83 F4 39 C6
PgUp NEC 83 F4 5C A3
PgDn NEC 83 F4 5D A2
Mouse NEC 83 F4 9B 64
Magnify NEC 83 F4 99 66
Volume + NEC 83 F4 5A A5
Volume - NEC 83 F4 5B A4
Panel Key Lock NEC 83 F4 5E A1
Freeze NEC 83 F4 61 9E
Pattern NEC 83 F4 7E 81
Blank NEC 83 F4 62 9D
Mute NEC 83 F4 9D 62
DynamicEco™ NEC 83 F4 7F 80
Timer NEC 83 F4 9C 63
Aspect NEC 83 F4 9A 65
RS232 command table

<Pin assignment for this two end>
Pin Description Pin Description
1 NC 2 RX
3 TX 4 NC
5 GND 6 NC
7 RTSZ 8 CTSZ
9 NC
65
<Interface>
RS-232 protocol
Baud Rate 115200 bps (default)
Data Length 8 bit
Parity Check None
Stop Bit 1 bit
Flow Control None
<RS232 command table>

Function Status Action cmd
Turn on 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x00 0x00 0x5D
Write
Turn off 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x01 0x00 0x5E
Power
Power status
Read 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x00 0x5E
(on/off)
Reset Execute 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x02 0x00 0x5F
Reset Color
Execute 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x2A 0x00 0x87
Settings
Splash Screen
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0A 0x00 0x67
Black
Splash Screen
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0A 0x01 0x68
Blue
Write
Splash Screen
Splash Screen 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0A 0x02 0x69
ViewSonic
Splash Screen
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0A 0x04 0x6B
Off
Splash Screen
Read 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x0A 0x68
status
Quick Power
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0B 0x00 0x68
Off Off
Write
Quick Power Quick Power
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0B 0x01 0x69
Off Off On
Quick Power
Read 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x0B 0x69
Off status
High Altitude
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0C 0x00 0x69
Mode Off
Write
High Altitude High Altitude
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0C 0x01 0x6A
Mode Mode On
High Altitude
Read 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x0C 0x6A
Mode status
Lamp Mode
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x10 0x00 0x6D
Normal
Write
Lamp Mode
Lamp Mode 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x10 0x01 0x6E
Economic
Lamp Mode
Read 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x10 0x6E
status
Message Off 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x27 0x00 0x84
Write
Message Message On 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x27 0x01 0x85
Read Message status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x27 0x85
66
Front Table 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x00 0x5E
Rear Table 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x01 0x5F
Write
Projector Rear Ceiling 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x02 0x60
Position Front Ceiling 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x03 0x61
Projector
Read 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x00 0x5F
position status
OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x00 0x7E
Auto 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x01 0x7F
Frame
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x02 0x80
Write Sequential
3D Sync
Frame Packing 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x03 0x81
Top-Bottom 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x04 0x82
Side-by-Side 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x05 0x83
Read 3D Sync Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x20 0x7F
Off 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x21 0x00 0x7F
Write
On 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x21 0x01 0x80
3D Sync Invert
3D Sync Invert
Read 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x21 0x80
Status
Contrast
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x02 0x00 0x60
decrease
Write
Contrast Contrast
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x02 0x01 0x61
increase
Read Contrast ratio 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x02 0x61
Brightness
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x03 0x00 0x61
decrease
Write
Brightness Brightness
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x03 0x01 0x62
increase
Read Brightness 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x03 0x62
Aspect ratio
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x00 0x62
Auto
Aspect ratio 4:3 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x02 0x64
Aspect ratio
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x03 0x65
Write 16:9
Aspect ratio
Aspect ratio
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x04 0x66
16:10
Aspect ratio
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x06 0x68
Wide
Read Aspect ratio 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x04 0x63
Auto Adjust Execute 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x05 0x00 0x63
Horizontal
position shift 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x06 0x01 0x65
Write right
Horizontal
Horizontal
position 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x06 0x00 0x64
position shift left
Horizontal
position
Vertical position
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x07 0x00 0x65
shift up
Write
Vertical Vertical position
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x07 0x01 0x66
position shift down
read Vertical
position
67
Color
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x00 0x66
temperatureT1
Color
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x01 0x67
temperatureT2
Write
Color
Color 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x02 0x68
temperatureT3
temperature
Color
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x03 0x69
temperatureT4
Color
Read temperature 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x08 0x67
status
Blank on 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x09 0x01 0x68
Write
Blank Blank off 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x09 0x00 0x67
Read Blank status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x09 0x68
Decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0A 0x00 0x68
Keystone- Write
Increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0A 0x01 0x69
Vertical
Read Keystone status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x0A 0x69
Brightest 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x00 0x69
Movie 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x01 0x6A
User 1 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x02 0x6B
User 2 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x03 0x6C
Write
PC / Gaming 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x04 0x6D
Color mode
ViewMatch 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x05 0x6E
Dynamic PC 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x06 0x6F
Dynamic Movie 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x07 0x70
Preset mode
Read 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x0B 0x6A
status
Primary color R 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x00 0x6E
Primary color G 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x01 0x6F
Primary color B 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x02 0x70
Write
Primary color C 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x03 0x71
Primary Color
Primary color M 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x04 0x72
Primary color Y 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x05 0x73
Primary color
Read 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x10 0x6F
status
Hue decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x11 0x00 0x6F
Write
Hue Hue increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x11 0x01 0x70
Read Hue 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x11 0x70
Saturation
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x12 0x00 0x70
decrease
Write
Saturation Saturation
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x12 0x01 0x71
increase
Read Saturation 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x12 0x71
Gain decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x13 0x00 0x71
Write
Gain Gain increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x13 0x01 0x72
Read Gain 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x13 0x72
Freeze on 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x00 0x01 0x60
Write
Freeze Freeze off 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x00 0x00 0x5F
Read Freeze status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x13 0x00 0x60
68
Input source
0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x00 0x60
VGA
Input source
0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x08 0x68
VGA2
Input source
Write 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x05 0x65
Source input Composite
Input source
0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x06 0x66
SVIDEO
Input source
0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x03 0x63
HDMI
Read Source 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x13 0x01 0x61
Quick Auto
0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x02 0x01 0x62
Search on
Write
Quick Auto Quick Auto
0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x02 0x00 0x61
Search Search off
Quick Auto
Search status
RGB 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x28 0x00 0x85
Write YUV 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x28 0x01 0x86
HDMI Format Auto 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x28 0x02 0x87
HDMI Fomrat
status
Enhanced 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x29 0x00 0x86
Write
Normal 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x29 0x01 0x87
HDMI Range
HDMI Range
status
Mute on 0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x00 0x01 0x61
Write
Mute Mute off 0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x00 0x00 0x60
Read Mute status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x14 0x00 0x61
Increse Volume 0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x01 0x00 0x61
Write Decrese
Volume 0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x02 0x00 0x62
Volume
Read Volume 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x14 0x03 0x64
69
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x00 0x61
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x01 0x62
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x02 0x63
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x03 0x64
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x04 0x65
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x05 0x66
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x06 0x67
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x07 0x68
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x08 0x69
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x09 0x6A
Write 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0a 0x6B
Language
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0b 0x6C
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0c 0x6D
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0d 0x6E
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0e 0x6F
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0f 0x70
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x10 0x71
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x11 0x72
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x12 0x73
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x13 0x74
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x14 0x75
Read Language 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x15 0x00 0x62
Reset Lamp
Write 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x01 0x00 0x62
usuage hour
Lamp Time
Lamp usuage
hour
Read error
Error status Read 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x0C 0x0D 0x66
status
70
Customer Support
For technical support or product service, see the table below or contact your
reseller.
Note : You will need the product serial number.
T = Telephone
Country/Region Website Email
F = FAX
AUS= 1800 880 818
Australia/New Zealand www.viewsonic.com.au service@au.viewsonic.com
NZ= 0800 008 822
T (Toll-Free)= 1-866-463-4775
Canada www.viewsonic.com T (Toll)= 1-424-233-2533 service.ca@viewsonic.com
F= 1-909-468-3757
www.viewsoniceurope.
Europe www.viewsoniceurope.com/uk/support/call-desk/
com
Hong Kong www.hk.viewsonic.com T= 852 3102 2900 service@hk.viewsonic.com
India www.in.viewsonic.com T= 1800 266 0101 service@in.viewsonic.com
Korea www.kr.viewsonic.com T= 080 333 2131 service@kr.viewsonic.com
Latin America
www.viewsonic.com/la/ T= 0800-4441185 soporte@viewsonic.com
(Argentina)
Latin America (Chile) www.viewsonic.com/la/ T= 1230-020-7975 soporte@viewsonic.com
Latin America
www.viewsonic.com/la/ T= 01800-9-157235 soporte@viewsonic.com
(Columbia)
Latin America (Mexico) www.viewsonic.com/la/ T= 001-8882328722 soporte@viewsonic.com
Renta y Datos, 29 SUR 721, COL. LA PAZ, 72160 PUEBLA, PUE. Tel: 01.222.891.55.77 CON 10 LINEAS
Electroser, Av Reforma No. 403Gx39 y 41, 97000 Mérida, Yucatán. Tel: 01.999.925.19.16
Other places please refer to http://www.viewsonic.com/la/soporte/index.htm#Mexico
Latin America (Peru) www.viewsonic.com/la/ T= 0800-54565 soporte@viewsonic.com
Macau www.hk.viewsonic.com T= 853 2870 0303 service@hk.viewsonic.com
Middle East ap.viewsonic.com/me/ Contact your reseller service@ap.viewsonic.com
T= 1-800-688-6688 (English)
Puerto Rico & Virgin service.us@viewsonic.com
www.viewsonic.com T= 1-866-379-1304 (Spanish)
Islands soporte@viewsonic.com
F= 1-909-468-3757
Singapore/Malaysia/
www.viewsonic.com.sg T= 65 6461 6044 service@sg.viewsonic.com
Thailand
South Africa ap.viewsonic.com/za/ Contact your reseller service@ap.viewsonic.com
T (Toll-Free)= 1-800-688-6688
United States www.viewsonic.com T (Toll)= 1-424-233-2530 service.us@viewsonic.com
F= 1-909-468-3757
71
Limited Warranty
ViewSonic® Projector
What the warranty covers:

ViewSonic warrants its products to be free from defects in material and workmanship, under normal
use, during the warranty period. If a product proves to be defective in material or workmanship
during the warranty period, ViewSonic will, at its sole option, repair or replace the product with a
like product. Replacement product or parts may include remanufactured or refurbished parts or
components.
Limited Three (3) year General Warranty

Subject to the more limited one (1) year warranty set out below, North and South America: Three
(3) years warranty for all parts excluding the lamp, three (3) years for labor, and one (1) year for the
original lamp from the date of the first consumer purchase.
Other regions or countries: Please check with your local dealer or local ViewSonic office for the
warranty information.
Limited One (1) year Heavy Usage Warranty:

Under heavy usage settings, where a projector’s use includes more than fourteen (14) hours
average daily usage, North and South America: One (1) year warranty for all parts excluding the
lamp, one (1) year for labor, and ninety (90) days for the original lamp from the date of the first
consumer purchase; Europe: One (1) year warranty for all parts excluding the lamp, one (1) year for
labor, and ninety (90) days for the original lamp from the date of the first consumer purchase.
Other regions or countries: Please check with your local dealer or local ViewSonic office for the
warranty information.
Lamp warranty subject to terms and conditions, verification and approval. Applies to manufacturer’s
installed lamp only. All accessory lamps purchased separately are warranted for 90 days.
Who the warranty protects:

This warranty is valid only for the first consumer purchaser.
What the warranty does not cover:

1. Any product on which the serial number has been defaced, modified or removed.
2. Damage, deterioration, failure, or malfunction resulting from:
a. Accident, abuse, misuse, neglect, fire, water, lightning, or other acts of nature, improper
maintenance, unauthorized product modification, or failure to follow instructions supplied
with the product.
b. Operation outside of product specifications.
c. Operation of the product for other than the normal intended use or not under normal
conditions.
d. Repair or attempted repair by anyone not authorized by ViewSonic.
e. Any damage of the product due to shipment.
f. Removal or installation of the product.
g. Causes external to the product, such as electric power fluctuations or failure.
h. Use of supplies or parts not meeting ViewSonic’s specifications.
i. Normal wear and tear.
j. Any other cause which does not relate to a product defect.
3. Removal, installation, and set-up service charges.
72
How to get service:
1. For information about receiving service under warranty, contact ViewSonic Customer Support
(please refer to “Customer Support” page). You will need to provide your product’s serial
number.
2. To obtain warranted service, you will be required to provide (a) the original dated sales slip, (b)
your name, (c) your address, (d) a description of the problem, and (e) the serial number of the
product.
3. Take or ship the product freight prepaid in the original container to an authorized ViewSonic
service center or ViewSonic.
4. For additional information or the name of the nearest ViewSonic service center, contact
ViewSonic.
Limitation of implied warranties:

There are no warranties, express or implied, which extend beyond the description contained herein
including the implied warranty of merchantability and fitness for a particular purpose.
Exclusion of damages:
ViewSonic’s liability is limited to the cost of repair or replacement of the product. ViewSonic shall not
be liable for:
1. Damage to other property caused by any defects in the product, damages based upon
inconvenience, loss of use of the product, loss of time, loss of profits, loss of business
opportunity, loss of goodwill, interference with business relationships, or other commercial loss,
even if advised of the possibility of such damages.
2. Any other damages, whether incidental, consequential or otherwise.
3. Any claim against the customer by any other party.
Effect of local law:

This warranty gives you specific legal rights, and you may also have other rights which vary from
local authority. Some local governances do not allow limitations on implied warranties and/or do not
allow the exclusion of incidental or consequential damages, so the above limitations and exclusions
may not apply to you.
Sales outside the U.S.A. and Canada:

For warranty information and service on ViewSonic products sold outside of the U.S.A. and Canada,
contact ViewSonic or your local ViewSonic dealer.
The warranty period for this product in mainland China (Hong Kong, Macao and Taiwan Excluded) is
subject to the terms and conditions of the Maintenance Guarantee Card.
For users in Europe and Russia, full details of warranty provided can be found in www.
viewsoniceurope.com under Support/Warranty Information.
Projector Warranty Term Template In UG

VSC_TEMP_2005
73
Mexico Limited Warranty
ViewSonic® Projector
What the warranty covers:
ViewSonic warrants its products to be free from defects in material and workmanship, under normal
use, during the warranty period. If a product proves to be defective in material or workmanship during
the warranty period, ViewSonic will, at its sole option, repair or replace the product with a like product.
Replacement product or parts may include remanufactured or refurbished parts or components &
accessories.
How long the warranty is effective:
3 years for all parts excluding the lamp, 3 years for labor, 1 year for the original lamp from the date of the
first consumer purchase.
Lamp warranty subject to terms and conditions, verification and approval. Applies to manufacturer’s
installed lamp only.
All accessory lamps purchased separately are warranted for 90 days.
Who the warranty protects:
This warranty is valid only for the first consumer purchaser.
What the warranty does not cover:
1. Any product on which the serial number has been defaced, modified or removed.
2. Damage, deterioration or malfunction resulting from:
a. Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product
modification, unauthorized attempted repair, or failure to follow instructions supplied with the product.
b. Any damage of the product due to shipment.
c. Causes external to the product, such as electrical power fluctuations or failure.
d. Use of supplies or parts not meeting ViewSonic’s specifications.
e. Normal wear and tear.
f. Any other cause which does not relate to a product defect.
3. Any product exhibiting a condition commonly known as “image burn-in” which results when a static
image is displayed on the product for an extended period of time.
4. Removal, installation, insurance, and set-up service charges.
How to get service:
For information about receiving service under warranty, contact ViewSonic Customer Support (Please refer
to the attached Customer Support page). You will need to provide your product’s serial number, so please
record the product information in the space provided below on your purchase for your future use. Please
retain your receipt of proof of purchase to support your warranty claim.
For Your Records
Product Name: ________________________ Model Number: __________________________
Document Number: ____________________ Serial Number: ___________________________
Purchase Date: ________________________ Extended Warranty Purchase? _______________(Y/N)
If so, what date does warranty expire? _________
1. To obtain warranty service, you will be required to provide (a) the original dated sales slip, (b) your
name, (c) your address, (d) a description of the problem, and (e) the serial number of the product.
2. Take or ship the product in the original container packaging to an authorized ViewSonic service center.
3. Round trip transportation costs for in-warranty products will be paid by ViewSonic.
Limitation of implied warranties:
There are no warranties, express or implied, which extend beyond the description contained herein
including the implied warranty of merchantability and fitness for a particular purpose.
Exclusion of damages:
ViewSonic’s liability is limited to the cost of repair or replacement of the product. ViewSonic shall not be
liable for:
1. Damage to other property caused by any defects in the product, damages based upon inconvenience,
loss of use of the product, loss of time, loss of profits, loss of business opportunity, loss of goodwill,
interference with business relationships, or other commercial loss, even if advised of the possibility of
such damages.
2. Any other damages, whether incidental, consequential or otherwise.
3. Any claim against the customer by any other party.
4. Repair or attempted repair by anyone not authorized by ViewSonic.
74
Contact Information for Sales & Authorized Service (Centro Autorizado de Servicio) within Mexico:
Name, address, of manufacturer and importers:

México, Av. de la Palma #8 Piso 2 Despacho 203, Corporativo Interpalmas,
Col. San Fernando Huixquilucan, Estado de México
Tel: (55) 3605-1099 http://www.viewsonic.com/la/soporte/index.htm
NÚMERO GRATIS DE ASISTENCIA TÉCNICA PARA TODO MÉXICO: 001.866.823.2004
Hermosillo: Villahermosa:
Distribuciones y Servicios Computacionales Compumantenimietnos Garantizados, S.A. de C.V.
SA de CV. AV. GREGORIO MENDEZ #1504
Calle Juarez 284 local 2 COL, FLORIDA C.P. 86040
Col. Bugambilias C.P: 83140 Tel: 01 (993) 3 52 00 47 / 3522074 / 3 52 20 09
Tel: 01-66-22-14-9005 E-Mail: compumantenimientos@prodigy.net.mx
E-Mail: disc2@hmo.megared.net.mx
Puebla, Pue. (Matriz): Veracruz, Ver.:

RENTA Y DATOS, S.A. DE C.V. Domicilio: CONEXION Y DESARROLLO, S.A DE C.V. Av. Americas # 419
29 SUR 721 COL. LA PAZ ENTRE PINZÓN Y ALVARADO
72160 PUEBLA, PUE. Fracc. Reforma C.P. 91919
Tel: 01(52).222.891.55.77 CON 10 LINEAS Tel: 01-22-91-00-31-67
E-Mail: datos@puebla.megared.net.mx E-Mail: gacosta@qplus.com.mx
Chihuahua Cuernavaca
Soluciones Globales en Computación Compusupport de Cuernavaca SA de CV
C. Magisterio # 3321 Col. Magisterial Francisco Leyva # 178 Col. Miguel Hidalgo
Chihuahua, Chih. C.P. 62040, Cuernavaca Morelos
Tel: 4136954 Tel: 01 777 3180579 / 01 777 3124014
E-Mail: Cefeo@soluglobales.com E-Mail: aquevedo@compusupportcva.com
Distrito Federal: Guadalajara, Jal.:

QPLUS, S.A. de C.V. SERVICRECE, S.A. de C.V.
Av. Coyoacán 931 Av. Niños Héroes # 2281
Col. Del Valle 03100, México, D.F. Col. Arcos Sur, Sector Juárez
Tel: 01(52)55-50-00-27-35 44170, Guadalajara, Jalisco
E-Mail : gacosta@qplus.com.mx Tel: 01(52)33-36-15-15-43
E-Mail: mmiranda@servicrece.com
Guerrero Acapulco Monterrey:

GS Computación (Grupo Sesicomp) Global Product Services
Progreso #6-A, Colo Centro Mar Caribe # 1987, Esquina con Golfo Pérsico
39300 Acapulco, Guerrero Fracc. Bernardo Reyes, CP 64280
Tel: 744-48-32627 Monterrey N.L. México
Tel: 8129-5103
E-Mail: aydeem@gps1.com.mx
MERIDA: Oaxaca, Oax.:

ELECTROSER CENTRO DE DISTRIBUCION Y
Av Reforma No. 403Gx39 y 41 SERVICIO, S.A. de C.V.
Mérida, Yucatán, México CP97000 Murguía # 708 P.A., Col. Centro, 68000, Oaxaca
Tel: (52) 999-925-1916 Tel: 01(52)95-15-15-22-22
E-Mail: rrrb@sureste.com Fax: 01(52)95-15-13-67-00
E-Mail. gpotai2001@hotmail.com
Tijuana: FOR USA SUPPORT:

STD ViewSonic Corporation
Av Ferrocarril Sonora #3780 L-C 381 Brea Canyon Road, Walnut, CA. 91789 USA
Col 20 de Noviembre Tel: 800-688-6688 (English); 866-323-8056 (Spanish);
Tijuana, Mexico Fax: 1-800-685-7276
E-Mail: http://www.viewsonic.com
Projector Mexico Warranty Term Template In UG

VSC_TEMP_2006
75

Projector Manual 7409

Uploaded by

Copyright:

Available Formats

Projector Manual 7409

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Projector Manual 7409

Uploaded by

Copyright:

Available Formats

PJD5132/PJD5232L/PJD5134/

Model No. VS14926/VS14929/VS14928/VS14930/VS14117

CE Conformity for European Countries

Following information is only for EU-member states:

Lead (Pb) 0.1% < 0.1%

For Your Records

Product disposal at end of product life

Safety instructions for ceiling mounting of the

Projector Power Cord VGA Cable

• THIS APPARATUS MUST BE EARTHED.

1. Focus ring 8. Right

To use the remote mouse control keys 6. Enter

Remote control code

Remote control effective range

• 16:9 image on a 4:3 screen

(e): Screen (f): Center of lens

4:3 image on a 4:3 Screen 16:9 image on a 4:3 Screen

• 16:10 image on a 4:3 screen

(e): Screen (f): Center of lens

16:10 image on a 16:10 Screen 16:10 image on a 4:3 Screen

There is 3% tolerance among these numbers due to optical component variations. It is

Notebook or desktop computer

1. VGA cable 5. S-Video cable

Connecting an HDMI device

• The HDMI input is only available on the PJD5134/PJD5234L/PJD5533w models.

Connecting a Component Video source device

To connect the projector to a Component Video source device:

To connect the projector to an S-Video source device:

Connecting a composite Video source device

To connect the projector to a composite Video source device:

Below is the overview of the OSD menu.

Screen Color Off

1. Press MENU/EXIT on the projector or 3. Press to highlight

Analog RGB MENU Exit

2. Use / to highlight the SYSTEM 4. Press MENU/EXIT twice* on

Analog RGB MENU Exit

: DISPLAY : SYSTEM SETTING: BASIC

: PICTURE : SYSTEM SETTING: ADVANCED

If you forget the password

displayed lasting for three seconds, and the message

Changing the password

2. Press / until your desired signal is

Changing HDMI input settings

Adjusting the projected image

Auto-adjusting the image

Fine-tuning the image clarity

Magnifying and searching for details

1. Auto: Scales an image proportionally to fit the

3. 16:9: Scales an image so that it is displayed in

4. 16:10 (PJD5533w only): Scales an image so

5. Wide (PJD5533w only): Scales a 4:3 aspect

Picture modes for different types of signals

Setting the User 1/User 2 mode

5. Press / to select a picture mode that is closest to your need.

Using Screen Color

Fine-tuning the image quality in user modes

Top-Left Bottom-Left Top-Right Bottom-Right

To cancel the timer, perform the following steps:

Locking control keys

1. Press on the projector or Lock on the remote control, or go to the SYSTEM