PRODUCT DATA SHEET

SikaGrout®
ONE-COMPONENT, HIGH PERFORMANCE, CEMENTITIOUS GROUT MIX

PRODUCT DESCRIPTION CHARACTERISTICS / ADVANTAGES

SikaGrout® is a non-shrink, cementitious grout with a ▪ Easy to use, just add water
unique 2-stage shrinkage compensating mechanism. It is ▪ Multiple fluidity with one material
non-metallic and contains no chloride. ▪ Non-metallic, will not stain or rust
With a special blend of shrinkage-reducing and ▪ Low heat build-up
plasticizing/water-reducing agents, SikaGrout® ▪ Excellent for pumping: Does not segregate, even at
compensates for shrinkage in both the plastic and high flow. No build-up on equipment hopper
hardened states. A structural grout, SikaGrout® provides ▪ Superior freeze/thaw resistance
the advantage of multiple fluidity with a single ▪ Resistant to oil and water
component. ▪ Meets ASTM C-1107
▪ Shows positive expansion when tested in accordance
USES with ASTM C-827
▪ SikaGrout® is USDA-approved
▪ Use for structural grouting of column base plates,
machine base plates, anchor rods, bearing plates, etc.
▪ Use on grade, above and below grade, indoors and out
▪ Multiple fluidity allows ease of placement: ram in place
as a dry pack, trowel-apply as a medium flow, pour or
pump as high flow

PRODUCT INFORMATION
Packaging 50 lb. (22.7 kg) multi-wall bags; 36 bags/pallet
Appearance / Color Concrete gray
Shelf Life 12 months in original, unopened bags
Storage Conditions Store dry at 40 to 95 °F (4 to 35 °C). Condition material to 65 to 75 °F (18 to
24°C) before using

Product Data Sheet

SikaGrout®
June 2018, Version 01.01
020201010010000218

1/4
TECHNICAL INFORMATION
Compressive Strength Plastic1 Flowable1 Fluid2 (CRD C-621)
1 day 4,500 3,500 2,700 Tested at:
(31 MPa) (24.1 MPa) (18.6 MPa) 73 °F (23 °C)
7 day 6,100 5,700 5,500 50 % R.H.
(42 MPa) (39.3 MPa) (37.9 MPa)
28 day 7,500 6,200 5,800
(51.7 MPa) (42.7 MPa) (40 MPa)
1CRD C-227: 100–124 % (plastic), 124–145 % (flowable)
2CRD C-611: 10–30 sec efflux time.

Flexural Strength Plastic1 Flowable1 Fluid2 (ASTM C-293)

28 day 1,400 1,200 1,000 Tested at:
(9.6 MPa) (8.2 MPa) (6.8 MPa) 73 °F (23 °C)
50 % R.H.
1CRD C-227: 100–124 % (plastic), 124–145 % (flowable)
2CRD C-611: 10–30 sec efflux time.

Splitting Tensile Strength Plastic1 Flowable1 Fluid2 (ASTM C-496)

28 day 600 575 500 Tested at:
(4.1 MPa) (3.9 MPa) (3.4 MPa) 73 °F (23 °C)
50 % R.H.
1CRD C-227: 100–124 % (plastic), 124–145 % (flowable)
2CRD C-611: 10–30 sec efflux time.

Shear Strength Plastic1 Flowable1 Fluid2 (ASTM C-882 mod.)

28 day 2,000 1,900 1,900 Hardened concrete
(13.7 MPa) (13.1 MPa) (13.1 MPa) to plastic grout
Tested at:
73 °F (23 °C)
50 % R.H.
1CRD C-227: 100–124 % (plastic), 124–145 % (flowable)
2CRD C-611: 10–30 sec efflux time.

Expansion Plastic1 Flowable1 Fluid2 (CRD C-621)

28 day +0.021 % +0.056 % +0.027 % Tested at:
73 °F (23 °C)
50 % R.H.
1CRD C-227: 100–124 % (plastic), 124–145 % (flowable)
2CRD C-611: 10–30 sec efflux time.

APPLICATION INFORMATION
Mixing Ratio Plastic1 Flowable1 Fluid2 (ASTM C-109:
6 pt.+ 6.5 pt. 8.5 pt. Plastic/Flowable)
(ASTM C-939: Fluid)
1CRD C-227: 100–124 % (plastic), 124–145 % (flowable)
2CRD C-611: 10–30 sec efflux time.

Coverage Approximately 0.44 cu. ft./bag at high flow

Thinner Plastic1 Flowable1 Fluid2 (ASTM C-266)
Initial 3.5–4.5 h 4.0–5.0 h 4.5–6.5 h Tested at:
Final 4.5–5.5 h 5.5–6.5 h 6.0–8.0 h 73 °F (23 °C)
50 % R.H.
1CRD C-227: 100–124 % (plastic), 124–145 % (flowable)
2CRD C-611: 10–30 sec efflux time.

Product Data Sheet

SikaGrout®
June 2018, Version 01.01
020201010010000218

2/4
APPLICATION INSTRUCTIONS LIMITATIONS
SURFACE PREPARATION ▪ Minimum ambient and substrate temperature 45 °F (7
°C)and rising at time of application
Remove all dirt, oil, grease, and other bond-inhibiting ▪ Minimum application thickness: 1/2 in. (12.7 mm)
materials by mechanical means. Anchor bolts to be ▪ Maximum application thickness (neat): 4 in. (50 mm).
grouted must be de-greased with suitable solvent. However, thicker applications can be achieved
Concrete must be sound and roughened to a CSP 4 or ▪ Contact Sika’s Technical Services Department (800-933-
higher to promote mechanical adhesion. Prior to 7452) for further information
pouring, surface should be brought to a saturated ▪ Do not use as a patching or overlay mortar or in
surface-dry condition. Steel should be cleaned and unconfined areas
prepared thoroughly by blastcleaning to a white metal ▪ Material must be placed within 15 minutes of mixing
finish. Follow standard industry and Sika guidelines for ▪ As with all cement based materials, avoid contact with
use as an anchoring epoxy. aluminum to prevent adverse chemical reaction and
possible product failure. Do not use on potential areas
For pourable grout, construct forms to retain grout such as aluminum bars, rails, posts etc.
without leakage. Forms should be lined or coated with
bond-breaker for easy removal. Forms should be BASIS OF PRODUCT DATA
sufficiently high to accommodate head of grout. Where
grout-tight form is difficult to achieve, use SikaGrout® in Results may differ based upon statistical variations
dry pack consistency. depending upon mixing methods and equipment,
temperature, application methods, test methods, actual
MIXING site conditions and curing conditions.
Mix manually or mechanically. Mechanically mix with
low-speed drill (400–600 rpm) and Sika mixing paddle or OTHER RESTRICTIONS
in appropriately sized mortar mixer. Make sure all
forming, mixing, placing, and clean-up materials are on See Legal Disclaimer.
hand. Add appropriate quantity of clean water to
achieve desired flow. Add bag of powder to mixing ENVIRONMENTAL, HEALTH AND SAFETY
vessel. Mix to a uniform consistency, minimum of 2
For further information and advice regarding
minutes. Ambient and material temperature should be
transportation, handling, storage and disposal of
as close as possible to 70 °F (21 °C). If higher, use cold
chemical products, user should refer to the actual Safety
water; if colder, use warm water.
Data Sheets containing physical, environmental,
toxicological and other safety related data. User must
Product Extension: For deeper applications, SikaGrout®
read the current actual Safety Data Sheets before using
(plastic and flowable consistencies only) may be
any products. In case of an emergency, call CHEMTREC
extended with 25 lb. (11.3 L) of 3/8 in. (9.5 mm) pea
at 1-800-424-9300, International 703-527-3887.
gravel. The aggregate must be nonreactive, clean,
wellgraded, saturated surface dry, have low absorption
and high density, and comply with ASTM C33 size
number 8 per Table 2. Add the pea gravel after the water
and SikaGrout.
APPLICATION
Within 15 minutes after mixing, place grout into forms in
normal manner to avoid air entrapment. Vibrate, pump,
or ram grout as necessary to achieve flow or
compaction. SikaGrout® must be confined in either the
horizontal or vertical direction leaving minimum exposed
surface. SikaGrout® is an excellent grout for pumping,
even at high flow. For pump recommendations, contact
Technical Service. Wet cure for a minimum of 3 days or
apply a curing compound which complies with ASTM C-
309 on exposed surfaces.

Tooling and Finishing

After grout has achieved final set, remove forms, trim or
shape exposed grout shoulders to designed profile.

Product Data Sheet

SikaGrout®
June 2018, Version 01.01
020201010010000218

3/4
LEGAL DISCLAIMER
• KEEP CONTAINER TIGHTLY CLOSED
• KEEP OUT OF REACH OF CHILDREN
• NOT FOR INTERNAL CONSUMPTION
• FOR INDUSTRIAL USE ONLY
• FOR PROFESSIONAL USE ONLY

Prior to each use of any product of Sika Corporation, its

subsidiaries or affiliates (“SIKA”), the user must always
read and follow the warnings and instructions on the
product’s most current product label, Product Data
Sheet and Safety Data Sheet which are available at
usa.sika.com or by calling SIKA’s Technical Service
Department at 1-800-933-7452. Nothing contained in
any SIKA literature or materials relieves the user of the
obligation to read and follow the warnings and
instructions for each SIKA product as set forth in the
current product label, Product Data Sheet and Safety
Data Sheet prior to use of the SIKA product.

SIKA warrants this product for one year from date of

installation to be free from manufacturing defects and to
meet the technical properties on the current Product
Data Sheet if used as directed within the product’s shelf
life. User determines suitability of product for intended
use and assumes all risks. User’s and/or buyer’s sole
remedy shall be limited to the purchase price or
replacement of this product exclusive of any labor costs.
NO OTHER WARRANTIES EXPRESS OR IMPLIED SHALL
APPLY INCLUDING ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE. SIKA SHALL NOT BE LIABLE UNDER ANY
LEGAL THEORY FOR SPECIAL OR CONSEQUENTIAL
DAMAGES. SIKA SHALL NOT BE RESPONSIBLE FOR THE
USE OF THIS PRODUCT IN A MANNER TO INFRINGE ON
ANY PATENT OR ANY OTHER INTELLECTUAL PROPERTY
RIGHTS HELD BY OTHERS.

Sale of SIKA products are subject to the Terms and

Conditions of Sale which are available at
https://usa.sika.com/en/group/SikaCorp/termsandcondi
tions.html or by calling 1-800-933-7452.

Sika Corporation Sika Mexicana S.A. de C.V.

201 Polito Avenue Carretera Libre Celaya Km. 8.5
Lyndhurst, NJ 07071 Fracc. Industrial Balvanera
Phone: +1-800-933-7452 Corregidora, Queretaro
Fax: +1-201-933-6225 C.P. 76920
usa.sika.com Phone: 52 442 2385800
Fax: 52 442 2250537

SikaGrout-en-US-(06-2018)-1-1.pdf

Product Data Sheet

SikaGrout®
June 2018, Version 01.01
020201010010000218

4/4