VI-86F

RFID Integrated Reader

Directory of Product
Information

 Shenzhen Vanch Intelligent Technology Co., Ltd has the right to do revisions for
hardware, software and manual of product without statement.And this manual is
subject to change without notice.
 Specifications and power of this product is subject to standard in origin.please being
sure that voltage is up to requirement, read and learn about safety precautions,
especially in open-air installation of outdoor.
 Content | VI-86F Directory of Product Information

Content
1 PRODUCT SUMMARIZE.............................................................................3

1.1 SHAPE AND INTERFACE................................................................................3

1.2 PERFORMANCE INDEX..................................................................................4
1.3 FUNCTION................................................................................................. 5

2 DEVICE INSTALLATION.............................................................................6

2.1 CONNECTION.............................................................................................. 6
2.2 CONNECTOR AND CONTROLLER.....................................................................6
2.3 CONNECTION POWER SUPPLY........................................................................7
2.4 DEVICE ADJUSTMENT...................................................................................7
2.5 TAG PLACE................................................................................................ 8

3 USUAL FAULTS.........................................................................................9

4 AFTER-SALES SERVICE...........................................................................10

4.1 SUPPORT AND SERVICE..............................................................................10

4.2 Service Hotline.....................................................................................12

090909RevA|Page 2 of 13
 Product Summarize | VI-86F Directory of Product Information

1 Product Summarize
VI-86F integrated reader is the latest product developed by us, which can

read and write tag or card in accordance with ISO18000-6B/ISO180006C.It

is widely used for vehicle access management, ETC, access management,

electronic security, logistic, production automatic management and so on.

1.1 Shape And Interface

Shape of VI-86F integrated reader is as follow picture, which is with ABS

shell, it can be installed inside or outside of house, is good at windproof,

dustproof and rainproof.

There is an interface at the bottom of VI-86F reader, connection line

shows as follows:

Red Black Blue Yello Grey Purpl orang palm darkg white
w e e reen
Trigg
Wieg Wieg
Powe ering
and_ and_ Signa 232T 232R
+12V r Signa 485+ 485-
Data Data l GND x x
GND l
1 0
Input

090909RevA|Page 3 of 13
 Product Summarize | VI-86F Directory of Product Information

2-1-2

Communication interface in the table of 2-1-2 is of features as follows:

A. RS232 Communication interface:

One of RS232 interfaces (DB9jack: RxD receive, Txd send, signal) can be

connected directly with PC string mouth.

B. Buzzer: inlay buzzer, it sounds whenever reader reads electronic

tag.

C. Power supply interface: +12V DC outlet (the red one and black

one).

D. I/O interface

 A RS485 interface (485+ (purple), 485-(orange) signal difference)-for

distant signal transmission.

 A wiegand interface: offen use the interface transmission signal in

access control system.

Wiegand : use WDATA1-0(yellow),WDATA1-1(blue) 2 lines，

Wiegand interface:

 Signal ground (brown): one GND line for wiegand interface and RS232

interface.

 One trigger signal access,for input:FIN1(grey),low level trigger

When reader in tigger work way, if make down-lead connect with

low level trigger, then reader begins to read card numbers till

high level is recovered.

090909RevA|Page 4 of 13
 Product Summarize | VI-86F Directory of Product Information

1.2 Performance Index

（1） Read-write tag:electronic tag in accordance with ISO18000-6B/6C

（2） Operating frequency: 860～960MHz

（3） Way of Working:by FHSS or fixed frequency launch

（4） Output power:0-30dbm(could be a little difference from various

countries or area)

（5） Readdistance:read distance>500cm,write distance>100cm( antenna

and tag dependent)

（6） Read rate:32bits/word,6ms in time,average

（7） Write rate:32bits/word,50ms in time ,avreage

（8） Power supply:+12v direct current

（9） power:<6w ,in average

（10） Working temperature: -10℃~+55℃

1.3 Function

（1） Read tag:electronic tag in accordance with ISO18000-6B,6C

（2） Can read EPC tags in different length.(16,32,48,64,80 or 96bits)

（3） Can read EPC Data.

（4） Can read data from user area.

（5） Can read data from TID area

（6） Can read tag’s access and kill password

（7） Can write different length EPC code(16,32,48,64,80 and 96bits)

（8） Can write data of user area

（9） Can revise tag access and kill code

（10） EPC,TID and user area can be write-protected

（11） Password section can be write-protected

（12） Can kill tag

090909RevA|Page 5 of 13
 Device Installation | VI-86F Directory of Product Information

2 Device Installation
2.1 Connection

In system, the connection of reader, antenna, tag and controller (or PC

machine) shows as follows:

Figure 3-1-1 typical connection about the relevant equipments

2.2 Connector And Controller

VI-86F reader can connect with controller through any interface from
Weigand, RS485 or RS232

(1) Weigand Interface

Under Wiegand port communications, need to connect 3 pins (Data0

(yellow), Data1 (blue), GND (brown)) on reader’s line bank, with the
relevant 3 pins on application system control. Reader Wiegand port just
sends data unilaterally.

(2) RS485 interface

Under RS485 port communications, need to connect 2 pins (RS485+

(purple), RS485-(orange)) on reader’s line bank, with the relevant 2 pins
on application system control. Through the converter can also connect
with the PC serial port.

080818RevA|Page 6 of 13
 Device Installation | VI-86F Directory of Product Information

(3) RS232 interface

RS232 interface can connect with pc directly, by matched cable, length of

RS232 interface connection line should be less than 10 meters, drawing
shows as 3-2-3

Figure 3-2-2 Reader’s RS232 is connected with PC

2.3 Connection Power Supply

VI-86F reader adopts +12V/3A direct current power supply, we can supply
you reader with required alternating and current convertor,the way to
connect power is as follows:

(1) Check if voltage of alternating power supply and operating frequency

is in accordance with AC 100-240V/50Hz

(2) Make DC output pin of power convertor insert into +12V direct current
power interface of reader.

(3) Make 220V alternating power input line of convertor insert or connect
with line of alternating power supply.

(4) If the Indicator light of power supply is turn on ,that means workable

2.4 Device Adjustment

Key of device adjustment is: adjust height, direction angle, obiquity, to

make reader can read electronic tag in the expected range.Debugging
method：

080818RevA|Page 7 of 13
 Device Installation | VI-86F Directory of Product Information

(1) Turn on reader power supply,set reader to be mode of auto

working,close parameter setting procedure ,and disconnect with PC.

(2) Ture off reader power supply first, and then turn on, reader will
automatically turn into state of continuous working.

(3) As material of identified object and required tag is different,so tag

should be stuck to object with same material as identified
one,traverses object in the expected range of tag is to read.If reader
can get tag,then inlay buzzer tweets and green LED blinks.

(4) Adjust height and angle of antenna; make reading range at the best.

Note: reader only radiates microwave power when reading tag,

then adjuster should keep a distance of 30cm from antenna, that
is meet American FCC requirements.

2.5 Tag Place

In work process of RFID, tag place is a usual job, some notes are as
follows:

(1) Adopts gluewater recommended by factory

(2) If labeled in the surface of metal, professional glue is recommended.

(3) Labeled place has to be field tested to make sure read best.

Note: Our Company offers 2 species of tags to customers, in

ISO18000-6B standard

(1) Air medium.can be held to use, also can be instead by our block set,
insert card into it directly.

(2) Glass medium,card should be stuck on glass.(non water-solubility is

required)

080818RevA|Page 8 of 13
 Usual Faults | VI-86F Directory of Product Information

3 Usual Faults
Table 3-1 usual faults and solutions for reader

Fault Phenomena Possible Reason Solution

antenna is not Check antenna
connected well connection details
beyond to reading make card close to
area of Reader module antenna
Change a new
can not read card antenna is broken
antenna
Parameter of RF
Renew parameter
Power is too low
tag is broken Test in other tag
reader is broken Contact technician
Check the power supply
no power
connector and adapter
Check interface
Com ties up or through software
Cannot be
broken and test if it
connected with
cummunicates
reader
Set it to be in
baud rate is not set
accordance by
in accordance
software
reader is broken Contact technician
antenna is not Check details of
connected well antenna connection
Parameter value of renew factory
RF Power is too low parameter
Reading distance is
tag is not in
too near revolve tag in 90
accordance with
degree
antenna polarization
reader is broken Contact technician
tag is broken change a new tag

080818RevA|Page 9 of 13
 After-Sales Service | VI-86F Directory of Product Information

4 After-Sales Service

4.1 Support And Service

Website please be online with internet by computer; enter

http://www.vanch.NET to get specifications, purchasing devices and other

informations about VI-86F.

Customer support If you have doubts about instruction and can

not get solutions from our website,please contact our customers’ service

centre.If your device has to be repaired,please contact us for service

information,delivery instruction and maintenance cost excludes from after

service before it is sent out.

Service If device needs to be diagnosed or other service,please

contact our customers’ service centre.please don’t send it out before you

contact us.If your device is under guarantee,please prepare receipt of

purchasing.

Please do as follows before you contact us:

A. read introduction

B. prepare your machine

 model

 serial number

 receipt of purchasing

080818RevA|Page 10 of 13
 After-Sales Service | VI-86F Directory of Product Information

C. Prepare your machine, customer service representative maybe ask

you to operate machine.

D. Prepare your questions; detailed problem description can help

customer service representative solve your problem at the earliest.

Guarantee

Important information this text is a guarantee declaration for

hardware products, please read carefully.

One year guarantee for hardware

Shenzhen Vanch Intelligent Technology Co., Ltd offers this hardware

product guarantee for no faults in material and manufacture from receipt

date of purchasing.

If Shenzhen Vanch Intelligent Technology Co., Ltd receives fault advise as

above during Guarantee date.Shenzhen Vanch Intelligent Technology Co.

Ltd can decide whether to repair or replace the proved failure product.

If Shenzhen Vanch Intelligent Technology Co., Ltd can not repair or replace

the product within reasonable time, customer can ask for refundment.

Scope of warranty

Guarantee above excludes from faults caused as follows:

Misapplication,modification without authorization,open the

hardware,operates or stores up this product in an improper

080818RevA|Page 11 of 13
 After-Sales Service | VI-86F Directory of Product Information

environment,damages during transportation,improper maintaince,or

caused by not using software ,parts,media,article,expendable from

Shenzhen Vanch Intelligent Technology Co.,Ltd,or project not for this

product.

This is the only guarantee declaration for products from Shenzhen Vanch

Intelligent Technology Co., Ltd, noelse guarantee in writing or oral

Shenzhen Vanch Intelligent Technology will not be responsible for cases as

follows: direct, indirect, particular and accidental damage, including profit,

whatever it is based on guarantee declaration, agreement, defect, or any

other law theory.

Disclaimer clauses: Radio transmission equipment can make interference

to the task of any unprotected industry, medical and scientific

equipment.There is possible interference to other electronic equipment

when this equipment works.If any inquiries in this aspect, please consult

from Shenzhen Vanch Intelligent Technology Co.,Ltd for improvement.

4.2 Service Hotline

Thank you for choosing our product, we will support you with technology

about product application, and offer solutions to any difficulties.Contact

mode of our company are as follows:

Company: Shenzhen Vanch Intelligent Technology Co., Ltd

Address: 5F, 535, BaGua 6 st., FuTian district, Shenzhen, Guangdong,

China

Postal code: 518029

080818RevA|Page 12 of 13
 After-Sales Service | VI-86F Directory of Product Information

Tel: +86 755 82426775

Fax: +86 755 82403457

Website: www.vanch.cn

Email: info@vanch.net

080818RevA|Page 13 of 13