MT812E - Cell Master - Anritsu

Technical Data Sheet
Cell Master™
Compact Handheld
Base Station Analyzer
MT8212E MT8213E
2 MHz to 4 GHz 2 MHz to 6 GHz Cable & Antenna Analyzer
100 kHz to 4 GHz 100 kHz to 6 GHz Spectrum Analyzer
10 MHz to 4 GHz 10 MHz to 6 GHz Power Meter
Introduction
Anritsu introduces its latest generation compact handheld Base Station Analyzer for installation and maintenance of wireless networks.
Designed as a lightweight base station analyzer meeting virtually all the testing needs of an RF technician. The Cell Master features
Signal Analyzer options for 2G, 3G, and 4G cellular networks including LTE, and WiMAX, and for digital broadcast.
Cable and Antenna Analyzer Highlights Spectrum and Interference Analyzer Highlights
• Measurements: RL, VSWR, Cable Loss, DTF, Phase • Measurements: Occupied Bandwidth, Channel Power, ACPR, C/I
• 2-port Transmission Measurement: High/Low Power • Interference Analyzer: Spectrogram, Signal Strength, RSSI,
• Sweep Speed: 1 msec/data point, typical Interference Mapping
• Display: Single or Dual Measurement Touchscreen • Dynamic Range: > 95 dB in 10 Hz RBW
• Calibration: OSL, InstaCal™, and FlexCal™ • DANL: –152 dBm in 10 Hz RBW
• Bias Tee: 32 V internal • Phase Noise: –100 dBc/Hz max @ 10 kHz offset at 1 GHz
• Frequency Accuracy: ± 50 ppb with GPS On
Capabilities and Functional Highlights
• LTE (10 MHz B/W) • Fixed, Mobile WiMAX • Built-in Bias Tee • E1, T1, T3 Backhaul Analyzer
• GSM/EDGE • ISDB-T, ISDB-T SFN • Internal Power Meter • 3 hour battery operation time
• W-CDMA/HSDPA • PIM Analyzer • High Accuracy Power Meter • USB Data Transfer
• TD-SCDMA/HSDPA • Interference Analyzer • USB Power Sensors, 4 to 26 GHz • Master Software Tools
• CDMA, EV-DO • GPS tagging of stored traces • Coverage Mapping • Line Sweep Tools
Cell Master™ MT8212E/MT8213E Base Station Analyzer featuring 8.4 in. Daylight Viewable Touchscreen
Compact Size: 273 mm x 199 mm x 91 mm, (10.7 in x 7.8 in x 3.6 in), Lightweight: 3.71 kg, (8.2 lbs)
Cell Master™ MT8212E, MT8213E Base Station Analyzer Specifications
Cable and Antenna Analyzer
Measurements
Measurements VSWR
Return Loss
Cable Loss
Distance-to-Fault (DTF) Return Loss
Distance-to-Fault (DTF) VSWR
1-Port Phase
Smith Chart
Setup Parameters
Measurement Display Single/Dual Measurement Display with independent markers
Frequency Start/Stop, Signal Standard, Start Cal
DTF Start/Stop, DTF Aid, Units (m/ft), Cable Loss, Propagation Velocity, Cable, Windowing
Windowing Rectangular, Normal Side Lobe, Low Side Lobe, Minimum Side Lobe
Amplitude Top, Bottom Auto Scale, Full Scale
Sweep Run/Hold, Single/Continuous, RF Immunity (High/Low), Data Points, Averaging/
Smoothing,Output Power (High/Low)
Data Points 137, 275, 551, 1102, 2204
Markers Markers 1-6 (On/Off), Delta Makers 1-6 (On/Off), Marker to Peak/Valley, Marker Table
Traces Recall, Copy to Display Memory, No Trace Math, Trace ± Memory, Trace Overlay
Limit Line On/Off, Single Limit, Multi-segment (41), Limit Alarm, Clear
Calibration Start Cal, Cal Type (Standard/FlexCal™)
Save/Recall Setups, Measurements, Screen Shots Jpeg (save only)
Frequency
Frequency Range 2 MHz to 4 GHz (MT8212E), 2 MHz to 6 GHz (MT8213E)
Frequency Accuracy ≤ ± 2.5 ppm @ 25 °C
Frequency Resolution 1 kHz, (RF immunity low)
100 kHz, (RF immunity high)
Output Power
High 0 dBm, typical
Low –30 dBm, typical
Interference Immunity
On-Channel +17 dBm @ > 1.0 MHz from carrier frequency
On-Frequency 0 dBm within ± 10 kHz of the carrier frequency
Measurement Speed
Return Loss ≤ 1.00 msec/data point, RF immunity low, typical
Distance-to-Fault ≤ 1.25 msec/data point, RF immunity low, typical
Return Loss
Measurement Range 0 dB to 60 dB
Resolution 0.01 dB
VSWR
Measurement Range 1:1 to 65:1
Resolution 0.01
Cable Loss
Measurement Range 0 dB to 30 dB
Resolution 0.01 dB
Distance-to-Fault
Vertical Range Return Loss 0 dB to 60 dB
Vertical Range VSWR 1:1 to 65:1
Fault Resolution (meters) (1.5 x 108 x vp) / ∆F (vp = velocity propagation constant, ∆F is F2-F1 in Hz)
Horizontal Range (meters) 0 to (Data Points-1) x Fault Resolution, to a maximum of 1500 meters (4921 ft)
1-Port Phase
Measurement Range –180° to +180°
Resolution 0.01°
Smith Chart
Resolution 0.01
Page 2 of 28
Cable and Antenna Analyzer (continued)
Measurement Accuracy
Corrected Directivity > 42 dB, OSL Calibration
> 38 dB, InstaCal™ Calibration
Measurement Uncertainty
Optical Distance-to-Fault Module (P/N ODTF-1)

Wavelength 1550 nm, typical
Fiber Type Single Mode Fiber
Event Resolution 10.2 cm (0.335 ft) maximum, or 150 / (n*ΔF), ΔF in MHz, n is IOR
Horizontal Range 1020 meter (3345 ft) maximum, or (#dp-1) *Event Resolution
Optical Dynamic Range 30 dB
Optical Output Power 3 dBm, typical
RF Connector N(m)
Optical Connector FC/APC
Datasheet 11410-00478 (for complete specifications)
PIM Analyzer (Option 0419) (Requires PIM Master™)

See Product Brochure 11410-00546
2-Port Transmission Measurement (Option 0021)

Frequency
Frequency Resolution 10 Hz
Output Power
High 0 dBm, typical
Low –30 dBm, typical
Dynamic Range
2 MHz to 4 GHz 80 dB
4 GHz to 6 GHz 70 dB
Application Options Bias-Tee (On/Off), Impedance (50 Ω, 75 Ω, Other)
Bias-Tee (Option 0010)

Setup On/Off, Voltage, Current (Low/High)
Voltage Range +12 V to +32 V
Current (Low/High) 250 mA/450 mA, 1 A surge for 100 ms
Resolution 0.1 V
Page 3 of 28
Spectrum Analyzer
Measurements
Smart Measurements Field Strength (uses antenna calibration tables to measure dBm/m2 or dBmV/m)
Occupied Bandwidth (measures 99% to 1% power channel of a signal)
Channel Power (measures the total power in a specified bandwidth)
ACPR (adjacent channel power ratio)
AM/FM/SSB Demodulation (wide/narrow FM, USB and LSB), (audio out only)
C/I (carrier-to-interference ratio)
Coverage Mapping (requires Option 0431)
Setup Parameters
Frequency Center/Start/Stop, Span, Frequency Step, Signal Standard, Channel #
Amplitude Reference Level (RL), Scale, Attenuation Auto/Level, RL Offset, Pre-Amp On/Off, Detection
Span Span, Span Up/Down (1-2-5), Full Span, Zero Span, Last Span
Bandwidth RBW, Auto RBW, VBW, Auto VBW, RBW/VBW, Span/RBW
File Save, Recall, Delete, Directory Management
Save/Recall Setups, Measurements, Limit Lines, Screen Shots Jpeg (save only), Save-on-Event
Save-on-Event Crossing Limit Line, Sweep Complete, Save-then-Stop, Clear All
Delete Selected File, All Measurements, All Mode Files, All Content
Directory Management Sort Method (Name/Type/Date), Ascend/Descend, Internal/USB, Copy, Format USB
Sweep Functions
Sweep Single/Continuous, Sweep Mode (Fast, Performance, No FFT), Reset, Detection,
Minimum Sweep Time, Trigger Type, Gated Sweep (see Option 0090)
Detection Peak, RMS, Negative, Sample, Quasi-peak
Triggers Free Run, External, Video, Change Position, Manual
Trace Functions
Traces Up to three Traces (A, B, C), View/Blank, Write/Hold, Trace A/B/C Operations
Trace A Operations Normal, Max Hold, Min Hold, Average, # of Averages, (always the live trace)
Trace B Operations A  B, B  C, Max Hold, Min Hold
Trace C Operations A  C, B  C, Max Hold, Min Hold, A – B  C, B – A  C, Relative Reference (dB), Scale
Marker Functions
Markers Markers 1-6 each with a Delta Marker, or Marker 1 Reference with Six Delta Markers,
Marker Table (On/Off), All Markers Off
Marker Types Style (Fixed/Tracking), Noise Marker, Frequency Counter Marker
Marker Auto-Position Peak Search, Next Peak (Right/Left), Peak Threshold %, Set Marker to Channel,
Marker Frequency to Center, Delta Marker to Span, Marker to Reference Level
Marker Table 1-6 markers frequency and amplitude plus delta markers frequency amplitude and offset
Limit Line Functions
Limit Lines Upper/Lower, On/Off, Edit, Move, Envelope, Advanced, Limit Alarm, Default Limit
Limit Line Edit Frequency, Amplitude, Add Point, Add Vertical, Delete Point, Next Point Left/Right
Limit Line Move To Current Center Frequency, By dB or Hz, To Marker 1, Offset from Marker 1
Limit Line Envelope Create Envelope, Update Amplitude, Points (41 max), Offset, Shape Square/Slope
Limit Line Advanced Type (Absolute/Relative), Mirror, Save/Recall
Frequency
Frequency Range 100 kHz to 4 GHz (MT8212E), 100 kHz to 6 GHz (MT8213E)
Tuning Resolution 1 Hz
Frequency Reference Aging: ± 1.0 ppm/year
Accuracy: ± 1.5 ppm (25 °C ± 25 °C) + aging, ± 50 ppb with GPS On
Frequency Span 10 Hz to 4 GHz including zero span (MT8212E),
10 Hz to 6 GHz including zero span (MT8213E)
Sweep Time Minimum 100 ms, 10 µs to 600 seconds in zero span
Sweep Time Accuracy ± 2% in zero span
Bandwidth
Resolution Bandwidth (RBW) 10 Hz to 3 MHz in 1–3 sequence ± 10% (1 MHz max in zero-span) (–3 dB bandwidth)
Video Bandwidth (VBW) 1 Hz to 3 MHz in 1–3 sequence (–3 dB bandwidth)
RBW with Quasi-Peak Detection 200 Hz, 9 KHz, 120 kHz (–6 dB bandwidth)
VBW with Quasi-Peak Detection Auto VBW is On, RBW/VBW = 1
Page 4 of 28
Spectrum Analyzer (continued)
Spectral Purity
SSB Phase Noise @ 1 GHz –100 dBc/Hz, –110 dBc/Hz typical @ 10 kHz offset
–105 dBc/Hz, –112 dBc/Hz typical @ 100 kHz offset
–115 dBc/Hz, –121 dBc/Hz typical @ 1 MHz offset
Amplitude Ranges
Dynamic Range > 95 dB (2.4 GHz), 2/3 (TOI-DANL) in 10 Hz RBW
Measurement Range DANL to +26 dBm
Display Range 1 dB to 15 dB/div in 1 dB steps, ten divisions displayed
Reference Level Range –120 dBm to +30 dBm
Maximum Continuous Input +35 dBm
Attenuator Resolution 0 dB to 55 dB in 5 dB steps
Amplitude Units Log Scale Modes: dBm, dBV, dBmv, dBμV
Linear Scale Modes: nV, μV, mV, V, kV, nW, μW, mW, W, kW
Amplitude Accuracy
100 kHz to 4.0 GHz ± 1.25 dB, ± 0.5 dB typical
> 4.0 GHz to 6 GHz ± 1.50 dB, ± 0.5 dB typical
Displayed Average Noise Level (DANL)
Preamp Off Preamp On
(Reference level -20 dBm) (Reference level -50 dBm)
(RBW Normalized to 1 Hz, 0 dB attenuation) Maximum Typical Maximum Typical
10 MHz to 2.4 GHz –141 dBm –146 dBm –157 dBm –162 dBm
> 2.4 GHz to 4 GHz –136 dBm –141 dBm –154 dBm -159 dBm
> 4 GHz to 5 GHz –133 dBm –138 dBm –154 dBm –155 dBm
(RBW = 10 Hz, 0 dB attenuation)
10 MHz to 2.4 GHz –131 dBm –136 dBm –147 dBm –152 dBm
> 2.4 GHz to 4 GHz –126 dBm –131 dBm –144 dBm –149 dBm
Spurs
Residual Spurious < –90 dBm (RF input terminated, 0 dB input attenuation, > 10 MHz)
Input-Related Spurious < –75 dBc (0 dB attenuation, –30 dBm input, span < 1.7 GHz, carrier offset > 4.5 MHz)
Exceptions, typical < –70 dBc @ < 2.5 GHz, with 2072.5 MHz Input
< –68 dBc @ F1-280 MHz with F1 Input
< –70 dBc @ F1 + 190 MHz with F1 Input
< –52 dBc @ 7349-2F2 MHz, with F2 Input, where F2 < 2424.5 MHz
< –55 dBc @ 190.5 ± F1/2 MHz, with F1 Input, where F1 < 1 GHz
Third-Order Intercept (TOI)
Preamp Off (–20 dBm tones 100 kHz apart, 10 dB attenuation)
800 MHz +16 dBm
2400 MHz +20 dBm
200 MHz to 2200 MHz +25 dBm, typical
> 2.2 GHz to 5.0 GHz +28 dBm, typical
> 5.0 GHz to 6.0 GHz +33 dBm, typical
Second Harmonic Distortion
Preamp Off, 0 dB input attenuation, –30 dBm input
50 MHz –56 dBc
> 50 MHz to 200 MHz –60 dBc, typical
> 200 MHz to 3000 MHz –70 dBc, typical
VSWR
2:1, typical
Page 5 of 28
Coverage Mapping (Options 0431)
Measurements
Indoor Mapping Outdoor Mapping
RSSI RSSI
ACPR ACPR
Setup Parameters
Frequency Center/Start/Stop, Span, Freq Step, Signal Standard, Channel #, Channel Increment
Amplitude Reference Level (RL), Scale, Attenuation Auto/Level, RL Offset, Pre-Amp On/Off, Detection
Span Span, Span Up/Down (1-2-5), Full Span, Zero Span, Last Span
BW RBW, Auto RBW, VBW, Auto VBW, RBW/VBW, Span/VBW
Measurement Setup ACPR, RSSI
Point Distance / Time Setup Repeat Type Time Distance
Save Points Map Save KML, JPEG
Recall Points Map Recall Map, Recall KML Points only, Recall KML Points with Map, Recall Default Grid
Interference Analyzer (Option 0025)

Measurements Spectrum
Field Strength
Occupied Bandwidth
Channel Power
Adjacent Channel Power (ACPR)
AM/FM/SSB Demodulation (Wide/Narrow FM, Upper/Lower SSB), (audio out only)
Carrier-to-Interference ratio (C/I)
Spectrogram (Collect data up to 72 hours)
Signal Strength (Gives visual and aural indication of signal strength)
Received Signal Strength Indicator (RSSI) (collect data up to one week)
Gives visual and aural indication of signal strength
Signal ID (up to 12 signals)
Center Frequency
Bandwidth
Signal Type (FM, GSM, W-CDMA, CDMA, Wi-Fi)
Closest Channel Number
Number of Carriers
Signal-to-Nose Ratio (SNR) > 10 dB
Interference Mapping
Triangulate location of interference with on display maps
GPS Receiver Option (Option 0031) (Antenna sold separately, P/N 2000-1528-R)
Setup On/Off, Antenna Voltage 3.3/5.0 V, GPS Info
GPS Time/Location Indicator Time, Latitude, Longitude and Altitude on display
Time, Latitude, Longitude and Altitude with trace storage
High Frequency Accuracy Spectrum Analyzer, Interference Analyzer, CW Signal Analyzers
when GPS Antenna is connected < ± 50 ppb with GPS On, 3 minutes after satellite lock in selected mode
Connector SMA, Female
Page 6 of 28
Channel Scanner (Option 0027)
Number of Channels 1 to 20 Channels
Measurements Graph/Table, Max Hold (On/5 sec/Off), Freq/Channel, Current/Max, Single/Dual Color
Scanner Scan Channels, Scan Frequencies, Scan Customer List, Scan Script Master™
Amplitude Reference Level, Scale
Custom Scan Signal Standard, Channel, # of Channels, Channel Step Size, Custom Scan
Frequency Range 100 kHz to 4 GHz (MT8212E),
100 kHz to 6 GHz (MT8213E)
Frequency Accuracy ± 10 Hz + Time base error
Measurement Range –110 dBm to +26 dBm
CW Signal Generator Option (Option 0028) (Requires CW Signal Generator Kit, P/N 69793)
Setup Parameters
Frequency Frequency, Signal Standard, Channel Number, Display Setup Help
Amplitude Power Level (Low/High), Offset (dB)
Frequency Range 2 MHz to 2 GHz
Frequency Reference Accuracy: ± 1.5 ppm (25 °C ± 25 °C) + aging, < ± 50 ppb with GPS On
Output Power High 0 dBm typical, Low –30 dBm typical
Attenuator (included in kit 69793): 0 to 90 dB in 1 dB steps
Gated Sweep (Option 0090)

Mode Spectrum Analyzer, Sweep
Trigger External TTL
Setup Gated Sweep (On/Off)
Gate Polarity (Rising, Falling)
Gate Delay (0 ms to 65 ms typical)
Gate Length (1 µs to 65 ms typical)
Zero Span Time
Page 7 of 28
Power Meter
Frequency Center/Start/Stop, Span, Frequency Step, Signal Standard, Channel #, Full Band
Amplitude Maximum, Minimum, Offset, Relative On/Off, Units, Auto Scale
Average Acquisition Fast/Med/Slow, # of Running Averages
Limits Limit On/Off, Limit Upper/Lower
Span 1 kHz to 100 MHz
Display Range –140 dBm to +30 dBm, ≤ 40 dB span
Measurement Range –120 dBm to +26 dBm
Offset Range 0 dB to +100 dB
VSWR 2:1 typical
Maximum Continuous Input +35 dBm without attenuator
Accuracy Same as Spectrum Analyzer
Application Options Impedance (50 Ω, 75 Ω, Other)
High Accuracy Power Meter (Option 0019) (Requires external USB Power Sensor(s))
Amplitude Maximum, Minimum, Offset, Relative On/Off, Units, Auto Scale
Average # of Running Averages, Max Hold
Zero/Cal Zero On/Off, Cal Factor (Center Frequency, Signal Standard)
Limits Limit On/Off, Limit Upper/Lower
Power Sensor Model PSN50 MA24104A MA24106A MA24108/18/26A
Description High Accuracy Inline High High Accuracy Microwave
RF Power Sensor Power Sensor RF Power Sensor USB Power Sensor
Frequency Range 50 MHz to 6 GHz 600 MHz to 4 GHz 50 MHz to 6 GHz 10 MHz to 8 GHz
(MA24108A)
10 MHz to 18 GHz
(MA24118A)
10 MHz to 26 GHz
(MA24126A)
Connector Type N(m), 50 Ω Type N(m), 50 Ω Type N(m), 50 Ω Type N(m), 50 Ω

(MA24108/18A)
Type K(m), 50 Ω
(MA24126A)
Dynamic Range –30 dBm to +20 dBm +3 dBm to +51.76 dBm –40 dBm to +23 dBm –40 dBm to +20 dBm
(0.001 mW to 100 mW) (2 mW to 150 W) (0.1 µW to 200 mW) (0.1 µW to 100 mW)
VBW 100 Hz 100 Hz 100 Hz 50 kHz
Measurand True-RMS True-RMS True-RMS True-RMS, Slot Power,
Burst Average Power
Measurement Uncertainty ± 0.16 dB 1
± 0.17 dB 2
± 0.16 dB 1
± 0.18 dB3
Datasheet 11410-00414 11410-00483 11410-00424 11410-00504
(for complete specifications)
Notes: 1) Total RSS measurement uncertainty (0 ºC to 50 ºC) for power measurements of a CW signal greater than –20 dBm with
zero mismatch errors.
2) Expanded uncertainty with K=2 for power measurements of a CW signal greater than +20 dBm with a matched load.
Measurement results referenced to the input side of the sensor.
3) Expanded uncertainty with K=2 for power measurements of a CW signal greater than –20 dBm with zero mismatch errors.
Page 8 of 28
LTE Signal Analyzers (Options 0541, 0542, 0546)
Measurements
RF Modulation Over-the-Air (OTA) Pass/Fail
(Option 0541) (Option 0542) (Option 0546) (User Editable)
Channel Spectrum Constellation Scanner Pass Fail All
Channel Power Reference Signal Power (Up to six Sync Signals) Pass/Fail RF
Occupied Bandwidth Sync Signal Power Sync Signal Power Pass Fail Demod
ACPR EVM Cell ID Measurements
Spectral Emission Mask Frequency Error Sector ID Channel Power
RF Summary Carrier Frequency Group ID Occupied Bandwidth
Cell ID Dominance ACLR
Sector ID Modulation Results Frequency Error
Group ID (strongest sync signal) Carrier Frequency
Control Channel Power Dominance
RS EVM (peak)
P-SS EVM (rms)
S-SS RS Power
PBCH SS Power
PCFICH P-SS Power
Modulation Summary S-SS Power
PBCH Power
PCFICH Power
Cell ID
Group ID
Sector ID
Setup Parameters
Frequency E-UTRA bands 1 - 21 (tunable 10 MHz to 4.0 GHz)
Center, Signal Standard, Channel #, Closest Channel, Decrement/Increment Channel
Bandwidth 1.4, 3, 5, 10 MHz
Span Auto, 1.4, 3, 5, 10, 15, 20 MHz
Amplitude Scale/Division, Power Offset, Auto Range, Adjust Range
Sweep Single/Continuous, Trigger Sweep
EVM Mode Auto, PBCH only
Save/Recall Setup, Measurement, Screen Shot (save only), to Internal/External Memory
Measurement Summary Screens Overall Measurements, RF Measurements, Signal Quality Measurements
RF Measurements (Option 0541)
RF Channel Power Accuracy ± 1.5 dB, ± 1.0 dB typical, (RF input –50 dBm to +10 dBm)
Modulation Measurements (Option 0542)

Frequency Error ± 10 Hz + time base error, 99% confidence level
Residual EVM (rms) 2.0% typical (E-UTRA Test Model 3.1) (RF Input –50 dBm to +10 dBm)
Over-the-Air (OTA) Measurements (Option 0546)

Scanner Six strongest Sync Signals
Auto Save Yes
GPS Tagging and Logging Yes
Page 9 of 28
GSM/GPRS/EDGE Signal Analyzers (Options 0040, 0041)
Measurements
RF Demodulation Over-the-Air (OTA) Pass/Fail
(Option 0040) (Option 0041) (User Editable)
Channel Spectrum Phase Error RF Measurements and Channel Power
Channel Power EVM Demodulation can be made OTA. Occupied Bandwidth
Occupied Bandwidth Origin Offset Burst Power
Burst Power C/I There are no additional OTA Average Burst power
Average Burst Power Modulation Type Measurements. Frequency Error
Frequency Error Magnitude Error Phase Error
Modulation Type BSIC (NCC, BCC) EVM
BSIC (NCC, BCC) Origin Offset
Multi-channel Spectrum C/I
Power vs. Time (Frame/Slot) Magnitude Error
Channel Power
Occupied Bandwidth
Burst Power
Average Burst Power
Frequency Error
Modulation Type
BSIC (NCC, BCC)
Setup Parameters
GSM/EDGE Select Auto, GSM, EDGE
Frequency Center, Signal Standard, Channel #, Closest Channel, Decrement/Increment Channel
Amplitude Power Offset, Auto Range, Adjust Range
RF Measurements (Option 0040) (temperature range 15 °C to 35 °C)
Occupied Bandwidth Bandwidth within which 99% of the power transmitted on a single channel lies
Burst Power Error ± 1.5 dB, ± 1 dB typical, (–50 dBm to +20 dBm)
Demodulation (Option 0041) (temperature range 15 °C to 35 °C)

GSMK Modulation Quality (RMS Phase)
Measurement Accuracy ± 1 deg
Residual Error (GSMK) 1 deg
8 PSK Modulation Quality (EVM)
Measurement Accuracy ± 1.5%
Residual Error (8 PSK) 2.5%
Page 10 of 28
W-CDMA/HSDPA Signal Analyzers (Options 0044, 0045 or 0065, 0035)
Measurements
(Option 0044) (Option 0045 or 0065) (Option 0035) (User Editable)
Band Spectrum Code Domain Power Graph Scrambling Code Scanner (Six) Max Output Power
Channel Spectrum P-CPICH Power Scrambling Codes Frequency Error
Channel Power Channel Power CPICH EVM
Occupied Bandwidth Noise Floor Ec/Io CPICH
Peak-to-Average Power EVM Ec Occupied Bandwidth
Spectral Emission Mask Carrier Feed Through Pilot Dominance Spectral Mask
Single carrier ACLR Peak Code Domain Error OTA Total Power ACLR
Multi-carrier ACLR Carrier Frequency Multipath Scanner (Six) PCDE
Frequency Error Six Multipaths P-CCPCH
Control Channel Power Tau S-CCPCH
Abs/Rel/Delta Power Distance Code Spread 3
CPICH, P-CCPCH RSCP PICH
S-CCPCH, PICH Relative Power Code 128
P-SCH, S-SCH Multipath Power
HSDPA Test Models
Power vs. Time 1 (16), (32), (64)
Constellation 2
Code Domain Power Table 3 (16), (32)
Code, Status 4 (+CPICH), (-CIPCH)
EVM, Modulation Type 5 (2 HS), (4 HS), (8 HS)
Power, Code Utilization
Power Amplifier Capacity
Codogram
Setup Parameters
Scrambling Code, Threshold Auto, Manual
User Selectable Scrambling Code, S-CCPCH Spread, S-CCPCH Code, PICH Code, Threshold,
Max Amp Power, CPICH Power, Frequency Error Average
Maximum Spreading Factor 256, 512
Amplitude Scale/Division, Power Offset, Auto Range, Adjust Range, Units (dBm/Watts)
Marker Six Markers, Table On/Off
Frequency Range Bands I – XIV, XVII
RF Channel Power Accuracy ± 1.25 dB, ± 0.7 dB typical, (temperature range 15 °C to 35 °C)
Occupied Bandwidth Accuracy ± 100 kHz
Adjacent Channel Leakage Ratio (ACLR) –54 dB/–59 dB ± 0.8 dB @ 5 MHz/10 MHz offset, typical, Bands I – VI, VIII – XIV, XVII
–54 dB/–57 dB ± 1.0 dB @ 5 MHz/10 MHz offset, typical, Band VII
Demodulation (Option 0045 for W-CDMA only or 0065 for W-CDMA and HSDPA) (temperature range 15 °C to 35 °C)
EVM Accuracy ± 2.5%, 6% ≤ EVM ≤ 25%
Residual EVM (RMS) 3.25% typical
Code Domain Power ± 0.5 dB for code channel power > –25 dB,
16, 32, 64 DCPH (test model 1),
16, 32 DCPH (test model 2, 3)
CPICH (dBm) Accuracy ± 0.8 dB typical
Scrambling Code Scanner Six strongest Scrambling Codes
Multipath Scanner Multipath power of six signals relative to strongest pilot
Page 11 of 28
cdmaOne/CDMA2000 1X Signal Analyzers (Option 0042, 0043, 0033)
Measurements
(Option 0042) (Option 0043) (0ption 0033) (User Editable)
Channel Spectrum Code Domain Power Graph Pilot Scanner (Nine) Channel Power
Channel Power Pilot Power PN Occupied Bandwidth
Occupied Bandwidth Channel Power Ec/Io Peak-to-Average Power
Peak-to-Average Power Noise Floor Tau Spectral Mask Test
Spectral Emission Mask Rho Pilot Power Frequency Error
Multi-carrier ACPR Carrier Feed Through Channel Power Channel Frequency
Tau Pilot Dominance Frequency error
RMS Phase Error Multipath Scanner (Six) Pilot Power
Frequency Error Ec/Io Noise Floor
Abs/Rel/ Power Tau Rho
Pilot Channel Power Carrier Feed Through
Page Multipath Power Tau
Sync Limit Test – 10 Tests Averaged RMS Phase Error
Q Page Rho Code Utilization
Code Domain Power Table Adjusted Rho Measured PN
Code Multipath Pilot Dominance
Status Pilot Dominance Multipath Power
Power Pilot Power
Multiple Codes Pass/Fail Status
Code Utilization
Setup Parameters
PN Setup PN Trigger (No Trigger, GPS, External), PN Search Type (Auto, Manual), PN Offset
Walsh Codes 64, 128
Measurement Speed Fast, Normal, Slow
External Trigger Polarity Rising, Falling
Number of Carriers 1 to 5
Carrier Bandwidth 1.23, 1.24, 1.25 MHz
RF Channel Power Accuracy ± 1.5 dB, ± 1.0 dB typical, (RF input -50 dBm to +20 dBm)
Frequency Error ± 10 Hz + time base error, 99% confidence level (in slow mode)
Rho Accuracy ± 0.005, for Rho > 0.9
Residual Rho > 0.995, typical, > 0.99 maximum, (RF input –50 dBm to +20 dBm)
PN Offset 1 x 64 chips
Pilot Power Accuracy ± 1.0 dB typical, relative to channel power
Tau ± 0.5 µs typical, ± 1.0 µs maximum
Pilot Scanner Nine strongest pilots
Limit Test Average of ten tests compared to limit
Page 12 of 28
CDMA2000 1xEV-DO Signal Analyzers (Option 0062, 0063, 0034)
Measurements
Channel Spectrum MAC Code Domain Power Graph Pilot Scanner (Nine) Channel Power
Channel Power Pilot & MAC Power PN Occupied Bandwidth
Occupied Bandwidth Channel Power Ec/Io Peak-to-Average Power
Peak-to-Average Power Frequency Error Tau Carrier Frequency
Power vs. Time Rho Pilot Pilot Power Frequency Error
Pilot & MAC Power Rho Overall Channel Power Spectral Mask
Channel Power Data Modulation Pilot Dominance Noise Floor
Frequency Error Noise Floor Multipath Scanner (Six) Pilot Power
Idle Activity MAC Code Domain Power Table Ec/Io RMS Phase Error
On/Off Ratio Code Tau Tau
Spectral Emission Mask Status Channel Power Code Utilization
Multi-carrier ACPR Power Multipath Power Measured PN
Code Utilization Pilot Dominance
Data Code Domain Power Multipath Power
Active Data Power
Data Modulation
Rho Pilot
Rho Overall
Maximum Data CDP
Minimum Data CDP
Setup Parameters
PN Setup PN Trigger (No Trigger, GPS, External), PN Search Type (Auto, Manual), PN Offset
Walsh Codes 64, 128
External Trigger Polarity Rising, Falling
Slot Type Auto, Active, Idle
Number of Carriers 1 to 5
Carrier Bandwidth 1.23, 1.24, 1.25 MHz
RF Channel Power Accuracy ± 1.5 dB, ±1.0 dB typical, (RF input -50 dBm to +20 dBm)
EV-DO Compatibility Rev 0 and Rev A
Rho Accuracy ± 0.01, for Rho > 0.9
Residual Rho > 0.995 typical, > 0.99, maximum (RF input –50 dBm to +20 dBm)
PN Offset Within 1 x 64 chips
Pilot Power Accuracy ± 1.0 dB typical, relative to channel power
Tau ± 0.5 µs typical, ± 1.0 µs maximum
Pilot Scanner Nine strongest pilots
Page 13 of 28
IEEE 802.16 Fixed WiMAX Signal Analyzers (Options 0046, 0047)
Measurements
(Option 0046) (Option 0047) (User Editable)
Channel Spectrum Constellation RF Measurements and Channel Power
Channel Power RCE (RMS/Peak) Demodulation can be made OTA. Occupied Bandwidth
Occupied Bandwidth EVM (RMS/Peak) Burst Power
Power vs. Time Frequency Error There are no additional OTA Preamble Power
Channel Power Carrier Frequency Measurements. Crest Factor
Preamble Power Base Station ID Frequency Error
Data Burst Power Spectral Flatness Carrier Frequency
Crest Factor Adjacent Subcarrier Flatness EVM
ACPR EVM vs. Subcarrier/Symbol RCE
RCE Base Station ID
EVM
Frequency Error
Carrier Frequency
Base Station ID
Setup Parameters
Bandwidth 1.25, 1.50, 2.50, 3.50, 5.00, 5.50, 6.00, 7.00, 10.00 MHz
Cyclic Prefix Ratio (CP) 1/4, 1/8, 1/16, 1/32
Span 5, 10, 15, 20 MHz
Frame Length 2.5, 5.0, 10.0 msec
Frequency Error 0.07 ppm + time base error, 99% confidence level
Residual EVM (rms) 3% typical, 3.5% maximum (RF Input –50 dBm to +20 dBm)
Page 14 of 28
IEEE 802.16 Mobile WiMAX Signal Analyzers (Options 0066, 0067, 0037)
Measurements
Channel Spectrum Constellation Channel Power Monitor Channel Power
Channel Power RCE (RMS/Peak) Preamble Scanner (Six) Occupied Bandwidth
Occupied Bandwidth EVM (RMS/Peak) Preamble Downlink Bust Power
Power vs. Time Frequency Error Relative Power Uplink Burst Power
Channel Power CINR Cell ID Preamble Power
Preamble Power Base Station ID Sector ID Crest Factor
Downlink Burst Power Sector ID PCINR Frequency Error
Uplink Burst Power Spectral Flatness Dominant Preamble Carrier Frequency
ACPR Adjacent Subcarrier Flatness Base Station ID EVM
EVM vs. Subcarrier/Symbol RCE
RCE (RMS/Peak) Sector ID
EVM (RMS/Peak)
Frequency Error
CINR
Base Station ID
Sector ID
DL-MAP (Tree View)
Setup Parameters
Zone Type PUSC
DL-MAP Auto Decoding Convolutional Coding (CC), Convolutional Turbo Coding (CTC)
Bandwidths 3.50, 5.00, 7.00, 8.75, 10.00 MHz
Cyclic Prefix Ratio (CP) 1/8
Span 5, 10, 20, 30 MHz
Frame Lengths 5, 10 msec
Demodulation Auto, Manual, FCH


Frequency Error 0.02 ppm + time base error, 99% confidence level
Residual EVM (rms) 2.5% typical, 3.0% maximum, (RF Input –50 dBm to +20 dBm)
Channel Power Monitor Over time (one week), measurement time interval 1 to 60 sec
Preamble Scanner Six Strongest Preambles
Auto Save Yes
GPS Logging Yes
Page 15 of 28
TD-SCDMA/HSDPA Signal Analyzers (Options 0060, 0061, 0038)
Measurements
Channel Spectrum Code Domain Power/Error Code Scan (32) Occupied Bandwidth
Channel Power (QPSK/8 PSK/16 QAM) Scrambling Code Group Channel Power
Occupied Bandwidth Slot Power Tau Channel Power RCC
Left Channel Power DwPTS Power Ec/Io On/Off Ratio
Left Channel Occ B/W Noise Floor Pilot Dominance Peak-to-Average Ratio
Right Channel Power Frequency Error Tau Scan (Six) Frequency Error
Right Channel Occ B/W Tau Sync-DL# EVM
Power vs. Time Scrambling Code Tau Peak EVM
Six Slot Powers EVM Ec/Io Peak Code Domain Error
Channel Power (RRC) Peak EVM DwPTS Power Tau
DL-UL Delta Power Peak Code Domain Error Pilot Dominance Noise Floor
UpPTS Power
DwPTS Power
On/Off Ratio
Slot Peak-to-Average Power
Spectral Emission
Setup Parameters
Slot Selection Auto, 0-6
Trigger Trigger Type (No Trigger/GPS/External), External Trigger (Rising/Falling), Tau Offset
SYNC-DL Code Auto, 0-31
Scrambling/Midamble Code Auto, 0-127
Maximum Users Auto, 2, 4, 6, 8, 10, 12, 14, 16
User Selectable Uplink Switch Point, Number of Carriers (1, 3), Tau Offset
Demodulation Type Auto, QPSK, 8 PSK, 16 QAM
Sweep Hold/Run, Trigger Sweep
RF Channel Power Accuracy (RRC) ± 1.5 dB, ± 1.0 dB typical, (slot power –40 dBm to +10 dBm)
Frequency Error ± 10 Hz + time base error, in the presence of a downlink slot
Supported Modulation QPSK, 8 PSK, 16 QAM
Residual EVM (rms) 3% typical, P-CCPH slot power > –50 dBm
PN Offset Within 1 x 64 chips
Pilot Power Accuracy ± 1.0 dB typical
Timing Error (Tau) for Dominant SYNC-DL ± 0.2 µs (external trigger)
Spreading Factor 1, 16
Code Scanner 32 Sync Codes and associated Scrambling Code Groups
Tau Scanner Six strongest Sync Codes
Auto Save Yes
GPS Logging Yes
Page 16 of 28
ISDB-T (Options 0030, 0032) For full specifications, see Technical Data Sheet 11410-00436
Measurements
ISDB-T RF ISDB-T Signal Analysis ISDB-T Measurement Modes ISDB-T SFN Analysis
(Option 0030) (Option 0030) (Option 0030) (Option 0032)
Signal Power Constellation (w/zoom) Custom Delay Profile (w/zoom)
Channel Power Layer A, B, C, TMCC User specified measurement Inband Spectrum
Termination Voltage Sub-carrier MER and setup parameters Measured Data
Open Terminal Voltage Delay Profile (w/zoom) Easy Channel Power
Field Strength Frequency Response User specified measurements. Delay
Spectrum Monitor Measured Data Some setup parameters are DU Ratio
Channel Power Frequency automatically set or detected Power
Zone Center Channel Frequency Offset Batch Field Strength
Zone Center Frequency MER (Total, Layer A/B/C, User specified measurements
Spectrum Mask TMCC, AC1) and channels for automatic
Mask (Standard A) Japan Modulation (Layer A/B/C) measurement, display of
Mask (Standard B) Japan Mode, GI results and storage
Mask (Critical) Brazil Sub-carrier MER w/marker
Mask (Sub-critical) Brazil Delay w/marker
Mask (Non-critical) Brazil Frequency Response w/
Phase Noise marker
Spurious Emissions
Setup Parameters
Channel Map UHF (Japan), UHF (Brazil), None
Channel 13 to 62 (Japan), 14 to 69 (Brazil)
Frequency 35 MHz to 806 MHz
Pre-amp On, Off
Reference Level Setting –25 dBm to +20 dBm / 5 dB steps (Pre Amp: Off), –50 dBm to –10 dBm/10 dB steps (Pre Amp: On)
ISDB-T Signal Analyzer (Option 0030)

Channel Power Accuracy ± 2 dB, (RF input -84 dBm to -10 dBm)
Frequency Lock Range ± 90 kHz
Frequency Offset Accuracy ± (measurement frequency x reference frequency accuracy) ± 0.3 Hz
Residual MER ≥ 42 dB (Pre Amp: Off, Reference level: –20 dBm)
≥ 37 dB (Pre Amp: On, Reference level: –50 dBm)
Delay Profile Resolution 0.12 µs, 0.1 dB
Frequency Response Resolution 1 kHz, 0.1 dB
Phase Noise Range –40 dBc/Hz to –140 dBc/Hz
Spurious Emissions Search Range 5 MHz to 5x main signal frequency
ISDB-T SFN Analyzer (Option 0032)

Delay Profile Display Range –1008 μs to +1008 μs
Delay Wave Estimated Level Accuracy ± 2.5 dB
DU Ratio Accuracy ± 1 dB
Inband Spectrum Range ± 2.74 MHz (Mode 2), ± 2.76 MHz (Mode 3)
Page 17 of 28
Backhaul Analyzers (Options 0051, 0052, 0053)
T1 Bit-Error-Rate Tester (BERT) (Option 0051)
Measurements
Error Detection Frame Bits, Bit Errors, BER, BPV, CRC, PATLS
Error Analysis (ITU G-821) Errored Seconds (ES), Error Free Seconds (EFS), Severely Errored Seconds (SES),
Unavailable Seconds (UAS), Available Seconds (AS), Degraded Minutes (DGRM)
Rx Signal Frequency (± 5 ppm, Max/Min), Vpp (± 5%) (Max/Min), dBdsx, Clock Slips, Frame Slips
VF Frequency (100 Hz to 3000 Hz, ± 3 Hz), Power (-40.0 dBm to +3.0 dBm, ± 0.2 dBm)
Status (Historical and Current) Rx (Signal, Frame Sync, Pattern Sync), DS1 (Alarms, Errors, B8ZS)
Status (Current) Tx (Alarm On, Error On, Loop On)
Setup
BERT Display Table, Histogram, Event List, Clear History
VF Tx (Off/On), Channel (1-24), Tx Freq, Tx Level (–30 dBm to 0 dBm), Volume, Audio, Clear
Line Code AMI, B8ZS
Tx Clock Internal (1.544 MHz ± 5 ppm), Recovered, External
Tx LBO 0.0 dB, –7.5 dB, –15.0 dB
Rx Input Terminate (Bantam connector 100 Ω balanced),
Monitor (Connect via 20 dB pad in DSX, 20 dB flat gain)
Bridge (≥ 1000 Ω, –36 dB to +6 dB)
Framing ESF, SF-D4
Payload T1 (1.544 Mbps), Fractional T1 (Nx64, 64, 56, 16, 8 kbps)
Pulse Shapes Conform to ANSI T1.403 and ITU G.703
Patterns QRSS, PRBS (2-9, 2-11, 2-15, 2-20, 2-23), All Ones, All Zeros,
1-in-8 (1-in-7), 2-in-8, 3-in-24 T1 Daly, Six User defined (≤ 32 bits),
Inverse Patterns (On/Off), Remote Loop Up/Down
Loop Codes CSU, NIU, Link Type (In-Band, Data-Link), Self Loop Up/Down, Loop Code User Defined
Error Insertion Bit Error, Bit Error Rate (BER), BPV, Frame Bit Error, Error (On/Off)
Alarm Insertion AIS On/Off (Blue Alarm), RAI On/Off (Yellow Alarm)
Data Log 1 minute to 3 days
E1 Bit-Error-Rate Tester (BERT) (Option 0052)

Measurements
Error Detection Frame Bits, Bit Errors, BER, BPV, CRC, E Bits
VF Frequency (100 Hz to 3000 Hz), Power (–40.0 dBm to +3.0 dBm, ± 0.2 dBm)
Status (Historical and Current) Rx (Signal, FAS, Pattern Sync), E1 (Alarms, Errors)
Status (Current) Tx (Alarm On, Error On)
Setup
Line Code AMI, HDB3
Tx Clock Internal ( 2.048 MHz ± 5 ppm), Recovered, External
Rx Input Terminate (RJ48 120/75 Ω balanced, BNC 75 Ω unbalanced, –43 dB to +6 dB)
Bridge (≥ 1000 Ω, –43 dB to +6 dB)
Framing PCM30, PCM30 CRC-4, PCM31, PCM31 CRC-4
Payload E1 (2.048 Mbps), Fractional E1 (N x 64, 64, 16, 8 kbps)
Pulse Shapes Conform to ITU G.703
Patterns QRSS, PRBS (2-9, 2-11, 2-15, 2-20, 2-23), All Ones, All Zeros, 1010,
1-in-8 (1-in-7), 2-in-8, 3-in-24, Six User defined (≤ 32 bits), Inverse Patterns (On/Off)
Loopback Mode Self loop
Error Insertion Bit Error, Bit Error Rate (BER), Frame Bit Error, Error (On/Off)
Alarm Insertion AIS (On/Off) (Blue Alarm), RAI (On/Off) (Yellow Alarm)
Page 18 of 28
Backhaul Analyzers (Options 0051, 0052, 0053)
T3 Bit-Error-Rate Tester (BERT) (Option 0053)
Measurements
Error Detection Frame Bits, Bit Errors, BER, BPV, Lof Count, P-bit Errors, C-bit Errors, FEBE Errors
Error Analysis (ITU G-821) Excess Zeros, Errored Seconds (ES), Error Free Seconds (EFS),
Severely Errored Seconds (SES), Unavailable Seconds (UAS),
Available Seconds (AS), Degraded Minutes (DGRM), Pattern Loss Seconds (PATLS)
Rx Signal Frequency (± 5 ppm, Max/Min), Vpp (± 5%) (Max/Min), dBdsx
VF Frequency (100 Hz to 3000 Hz, ± 3 Hz), Power (–30.0 dBm to +0.0 dBm, ± 0.2 dBm)
Status (Historical and Current) Rx (Signal, Frame Sync, Pattern Sync), DS3 (Alarms, Errors, DS3ZS)
Status (Current) Insert (Alarm On, Error On, Loop On)
Setup
VF Tx (Off/On), Channel #, Tx Freq, Tx, Level, Volume, Audio (On/Off)
Line Code AMI, B3ZS
Tx Clock Internal (44.736 MHz ± 5 ppm), Recovered
Tx LBO Low, DSX
Rx Input DSX3 (Bantam connector 100 Ω balanced)
Monitor (Connect via 20 dB pad in DSX)
Framing M13, C-Bit, Unframed
Test Mode Auto, DS3, DS1
Pulse Shapes Carrier present, Frame ID and Sync, Pattern ID and Sync
Patterns QRSS, PRBS (2-9, 2-11, 2-15, 2-20, 2-23), All Ones, All Zeros, 1010,
Inverse Patterns (On/Off), Loop Up/Down
Loop Codes Stuff Bit, DS3 C-Bit FEAC, DS3 Self Loop
Error Insertion Bit Error, BPV, DS3 Frame Bit Error, C-bit, P-bit, FEBE, Error Insert (On/Off)
Alarm Insertion AIS (Blue Alarm), RAI (Yellow Alarm), Idle Alarm, Alarm (On/Off)
DS1 Test Mode

Measurements
Error Detection Frame Bits, Bit Errors, BER, BPV, CRC, PATLS
VF Frequency (100 Hz to 3000 Hz, ± 3 Hz), Power (–40.0 dBm to +3.0 dBm, ± 0.2 dBm)
Status (Historical and Current) Rx (Signal, Frame Sync, Pattern Sync), DS1 (Alarms, Errors, B8ZS)
Status (Current) Tx (Alarm On, Error On, Loop On)
Setup
Line Code AMI, B8ZS
Tx Clock Internal (1.544 MHz ± 5 ppm), Recovered, External
Tx LBO 0.0 dB, –7.5 dB, –15.0 dB
Rx Input Terminate (Bantam connector 100 Ω balanced)
Bridge (≥ 1000 Ω, –36 dB to +6 dB)
Framing ESF, SF-D4
Payload T1 (1.544 Mbps), Fractional T1 (Nx64, 64, 56, 16, 8 kbps)
Pulse Shapes Conform to ANSI T1.403 and ITU G.703
Patterns QRSS, PRBS (2-9, 2-11, 2-15, 2-20, 2-23), All Ones, All Zeros,
Inverse Patterns (On/Off), Remote Loop Up/Down
Loopback Mode CSU, NIU, Link Type (In-Band, Data-Link), Self Loop Up/Down, Loop Code User Defined
Error Insertion Bit Error, Bit Error Rate (BER), BPV, Frame Bit Error, Error (On/Off)
Alarm Insertion AIS On/Off (Blue Alarm), RAI On/Off (Yellow Alarm)
Page 19 of 28
General Specifications
All specifications and characteristics apply under the following conditions, unless otherwise stated: 1) After 5 minutes of warm-up time, where the instrument is
left in the ON state; 2) All specifications apply when using internal reference; 3) All specifications subject to change without notice; 4) Typical performance is the
measured performance of an average unit; 5) Recommended calibration cycle is 12 months; 6) Performance Sweep Mode.
Setup Parameters
System Status (Temperature, Battery Info, Serial Number, Firmware Version, Options Installed)
Self Test, Application Self Test
GPS (see Option 0031)
System Options Name, Date and Time, Brightness, Volume
Language (English, French, German, Spanish, Chinese, Japanese, Korean, Italian, User defined)
Reset (Factory Defaults, Master Reset, Update Firmware)
File Save, Recall, Delete, Directory Management
Save/Recall Setups, Measurements, Screen Shots Jpeg (save only)
Delete Selected File, All Measurements, All Mode Files, All Content
Directory Management Sort Method (Name/Type/Date), Ascend/Descend, Internal/USB, Copy, Format USB
Internal Trace/Setup Memory 2,000 traces, 2,000 setups
External Trace/Setup Memory Limited by size of USB Flash drive
Mode Switching Auto-Stores/Recalls most recently used Setup Parameters in the Mode
Connectors
RF Out Type N, female, 50 Ω (Reflection In)
RF Out Damage Level 23 dBm, ± 50 VDC
RF In Type N, female, 50 Ω
RF Input Damage Level +35 dBm peak, ± 50 VDC, Maximum Continuous Input (≥ 10 dB attenuation)
GPS SMA(f)
T1 Bantam Jacks
T3 BNC connectors
E1 RJ48C
External Power 5.5 mm barrel connector, 12.5 VDC to 15 VDC, < 4.0 Amps
USB Interface (2) Type A (Connect USB Flash Drive and Power Sensor)
USB Interface 5-pin mini-B, Connect to PC for data transfer and/or remote control
Headset Jack 2.5 mm mini-phone plug
External Reference In BNC, female, 50 Ω, Maximum Input +10 dBm
1 MHz, 5 MHz, 10 MHz, 13 MHz
External Trigger/Clock Recovery BNC, female, 50 Ω, Maximum Input ± 50 VDC
Display
Type Resistive Touchscreen
Size 8.4 in. daylight viewable color LCD
Resolution 800 x 600
Battery
Type Li-Ion
Battery Operation 3 hours, typical
Electromagnetic Compatibility
European Union CE Mark, EMC Directive 2004/108/EC
Low Voltage Directive 2006/95/EC
Australia and New Zealand C-tick N274
Interference EN 61326-1
Emissions EN 55011
Immunity EN 61000-4-2/-4-3/-4-4/-4-5/-4-6/-4-11
Safety
Safety Class EN 61010-1 Class 1
Product Safety IEC 60950-1 when used with Anritsu Company supplied Power Supply
Environmental
Operating Temperature –10 °C to 55 °C
Maximum Humidity 95% RH (none condensing) at 40 °C
Shock MIL-PRF-28800F Class 2
Storage –40 °C to 71 °C
Altitude 4600 meters, operating and non-operating
ESD
RF Port Center Pin Withstands up to ± 15 kV
Size and Weight
Size 273 mm x 199 mm x 91 mm, (10.7 in x 7.8 in x 3.6 in)
Weight 3.71 kg, (8.2 lbs)
Page 20 of 28
Line Sweep Tools (for your PC)
Trace Capture
Browse to Instrument View and copy traces from the test equipment to your PC using Windows Explorer
Open legacy files Open DAT files captured with Hand Held Software Tools v6.61
Open Current files Open VNA or DAT files
Capture plots to: The Line Sweep Tools screen, DAT files, Database, or JPEG
Traces
Trace Types Return Loss, VSWR, DTF-RL, DTF-VSWR, Cable Loss, Smith Chart, and PIM
Trace formats DAT, VNA, CSV, PNG, BMP, JPG, HTML, Data Base, and PDF
Report Generation
Report Generator Includes GPS location along with measurements
Report Format Create reports in HTML or PDF format
Report setup Report Title, Company, Prepared for, Location, Date and Time, Filename, Company logo
Trace Setup 1 trace Portrait Mode, 2 Trace Portrait Mode, 1 Trace Landscape Mode
Trace Validation
Presets 7 presets allow “one click” setting of up to 6 markers and one limit line
Marker Controls 6 regular Markers, Marker Peak, Marker valley, Marker between, and frequency entry
Delta Markers 6 Delta markers
Limit Line Enable and drag or value entry. Also works with presets
Next Trace Button Next Trace and Previous trace arrow keys allow quick switching between traces
Tools
Cable Editor Allows creation of custom cable parameters
Distance to Fault Converts a Return Loss trace to a Distance to Fault trace
Measurement Calculator Converts Real, Imaginary, Magnitude, Phase, RL, VSWR, Rho, and Transmit power
Signal Standard Editor Creates new band and channel tables
Renaming Grid 36 user definable phrases for creation of file names, trace titles, and trace subtitles
Connectivity
Connections Ethernet, USB cable, USB Memory Stick, and RS-232 Serial Null Modem cable
Master Software Tools (for your PC)

Mapping (GPS Required)
Spectrum Analyzer Mode MapInfo, MapPoint
Mobile WiMAX OTA, LTE OTA Options Google Earth, Google Maps, MapInfo
Folder Spectrogram (Spectrum Monitoring for Interference Analysis and Spectrum Clearing)
Folder Spectrogram – 2D View Creates a composite file of multiple traces
Peak Power, Total Power, Peak Frequency, Histogram, Average Power (Max/Min)
File Filter (Violations over limit lines or deviations from averages)
Playback
Video Folder Spectrogram – 2D View Create AVI file to export for management review/reports
Folder Spectrogram – 3D View Views (Set Threshold, Markers)
- 3D (Rotate X, Y, Z Axis, Level Scale, Signal ID)
- Playback (Frequency and/or Time Domain)
List/Parameter Editors
Traces Add, delete, and modify limit lines and markers
Product Updates Auto-checks Anritsu website for latest revision firmware
Firmware Upload Upload new firmware into the instrument
Pass/Fail Create, download, or edit Signal Analysis Pass/Fail Limits
Languages Add up to two languages or modify non-English language menus
Script Master™
Channel Scanner Mode Automate scan up to 1200 channels, repeat for sets of 20 channels, repeat all channels
GSM/GPRS/EDGE or W-CDMA/HSDPA Mode Automate Signal Analysis testing requirements with annotated how-to pictures
Connectivity
Connections Connect to PC using USB, Ethernet, or Serial, depending on the instrument
Firmware Updates Product Update: download latest firmware version
Page 21 of 28
Ordering Information
MT8212E MT8213E Description
2 MHz to 4 GHz 2 MHz to 6 GHz Cable and Antenna Analyzer
100 kHz to 4 GHz 100 kHz to 6 GHz Spectrum Analyzer
10 MHz to 4 GHz 10 MHz to 6 GHz Power Meter
Options Options
MT8212E-0419 MT8213E-0419 PIM Analyzer (requires PIM Master)
MT8212E-0021 MT8213E-0021 2-Port Transmission Measurement

MT8212E-0010 MT8213E-0010 Bias-Tee
MT8212E-0031 MT8213E-0031 GPS Receiver (requires Antenna P/N 2000-1528-R)

MT8212E-0019 MT8213E-0019 High-Accuracy Power Meter***
MT8212E-0025 MT8213E-0025 Interference Analyzer*

MT8212E-0027 MT8213E-0027 Channel Scanner
MT8212E-0431 MT8213E-0431 Coverage Mapping*
MT8212E-0090 MT8213E-0090 Gated Sweep

MT8212E-0028 MT8213E-0028 C/W Signal Generator (requires CW Signal Generator Kit, P/N 69793)
MT8212E-0040 MT8213E-0040 GSM/GPRS/EDGE RF Measurements

MT8212E-0041 MT8213E-0041 GSM/GPRS/EDGE Demodulation
MT8212E-0044 MT8213E-0044 W-CDMA/HSDPA RF Measurements

MT8212E-0045 MT8213E-0045 W-CDMA Demodulation
MT8212E-0065 MT8213E-0065 W-CDMA/HSDPA Demodulation
MT8212E-0035 MT8213E-0035 W-CDMA/HSDPA Over-the-Air Measurements*
MT8212E-0060 MT8213E-0060 TD-SCDMA/HSDPA Measurements

MT8212E-0061 MT8213E-0061 TD-SCDMA/HSDPA Demodulation
MT8212E-0038 MT8213E-0038 TD-SCDMA/HSDPA Over-the-Air Measurements
MT8212E-0541 MT8213E-0541 LTE RF Measurements*

MT8212E-0542 MT8213E-0542 LTE Modulation Measurement*
MT8212E-0546 MT8213E-0546 LTE Over-the-Air Measurements*
MT8212E-0042 MT8213E-0042 cdmaOne/CDMA2000 1X RF Measurements

MT8212E-0043 MT8213E-0043 cdmaOne/CDMA2000 1X Demodulation
MT8212E-0033 MT8213E-0033 cdmaOne/CDMA2000 1X Over-the-Air Measurements*
MT8212E-0062 MT8213E-0062 CDMA2000 1xEV-DO RF Measurements

MT8212E-0063 MT8213E-0063 CDMA2000 1xEV-DO Demodulation
MT8212E-0034 MT8213E-0034 CDMA2000 1xEV-DO Over-the-Air Measurements*
MT8212E-0046 MT8213E-0046 IEEE 802.16 Fixed WiMAX RF Measurements

MT8212E-0047 MT8213E-0047 IEEE 802.16 Fixed WiMAX Demodulation
MT8212E-0066 MT8213E-0066 IEEE 802.16 Mobile WiMAX RF Measurements

MT8212E-0067 MT8213E-0067 IEEE 802.16 Mobile WiMAX Demodulation
MT8212E-0037 MT8213E-0037 IEEE 802.16 Mobile WiMAX Over-the-Air Measurements
MT8212E-0030 MT8213E-0030 ISDB-T Digital Video Measurements

MT8212E-0032 MT8213E-0032 ISDB-T SFN Measurements
MT8212E-0051 MT8213E-0051 T1 Analyzer**

MT8212E-0052 MT8213E-0052 E1 Analyzer**
MT8212E-0053 MT8213E-0053 T3/T1 Analyzer**
MT8212E-0098 MT8213E-0098 Standard Calibration (ANSI Z540-1-1994)

MT8212E-0099 MT8213E-0099 Premium Calibration (ANSI Z540-1-1994 plus test data)
*Requires Option 0031, **Mutually exclusive,
***Requires External Power Sensor
Page 22 of 28
Power Sensors (For complete ordering information see the respective datasheets of each sensor)
Part Number Description
PSN50 High Accuracy RF Power Sensor, 50 MHz to 6 GHz, +20 dBm
MA24104A Inline High Power Sensor, 600 MHz to 4 GHz, +51.76 dBm
MA24106A High Accuracy RF Power Sensor, 50 MHz to 6 GHz, +23 dBm
MA24108A Microwave USB Power Sensor, 10 MHz to 8 GHz, +20 dBm
Manuals (soft copy included on Handheld Instruments Documentation Disc and at www.anritsu.com)
10920-00060 Handheld Instruments Documentation Disc
10580-00250 Cell Master Instrument User Guide (Hard copy included)

- Bias-Tee, GPS Receiver
10580-00241 Cable and Antenna Analyzer Measurement Guide
10580-00242 2-Port Transmission Measurement

User Guide
- Bias-Tee
Cell Master
MT8212E, MT8213E
10580-00244 Spectrum Analyzer Measurement Guide
- Interference Analyzer, Channel Scanner, Gated Sweep,
Compact Handheld Base Station Analyzer
CW Signal Generator, AM/FM/PM Analyzer,
Cable and Antenna Analyzer
Spectrum Analyzer Interference Mapping, Coverage Mapping
Power Meter
10580-00240 Power Meter Measurement Guide

- High Accuracy Power Meter
10580-00234 3GPP Signal Analyzer Measurement Guide

- GSM/EDGE, W-CDMA/HSDPA, TD-SCDMA/HSDPA, LTE
10580-00235 3GPP2 Signal Analyzer Measurement Guide

- CDMA, EV-DO
10580-00236 WiMAX Signal Analyzer Measurement Guide

- Fixed WiMAX, Mobile WiMAX
10580-00237 Digital TV Measurement Guide

- DVB-T/H, ISDB-T
10580-00238 Backhaul Analyzer Measurement Guide

- T1, E1, T3/T1
10580-00215 ODTF-1 Optical Distance-to-Fault Module

10580-00256 Programming Manual
10580-00280 PIM Master User Guide
Troubleshooting Guides (soft copy at www.anritsu.com)

11410-00473 Cable, Antenna and Components
11410-00551 Spectrum Analyzers
11410-00472 Interference
11410-00566 LTE eNode Testing
11410-00466 GSM/GPRS/EDGE Base Stations
11410-00463 W-CDMA/HSDPA Base Stations
11410-00465 TD-SCDMA/HSDPA Base Stations
11410-00467 cdmaOne/CDMA2000 1X Base Stations
11410-00468 CDMA2000 1xEV-DO Base Stations
11410-00470 Fixed WiMAX Base Stations
11410-00469 Mobile WiMAX Base Stations
11410-00552 T1/DS1 Backhaul Testing
11410-00553 E1 Backhaul Testing
Page 23 of 28
Standard Accessories (included with instrument)
10920-00060 Handheld Instruments Documentation Disc
10580-00250 Cell Master User Guide (includes Bias-Tee, GPS Receiver)
3-68736 Soft Carrying Case
2300-498 Master Software Tools (MST) CD Disc
2300-530 Anritsu Tool Box with Line Sweep Tools (LST) DVD Disc
633-44 Rechargeable Li-Ion Battery
40-168-R AC-DC Adapter
806-141-R Automotive Cigarette Lighter 12 VDC Adapter
3-2000-1498 USB A/5-pin mini-B Cable, 10 feet/305 cm
11410-00485 Cell Master MT8212E/MT8213E Technical Data Sheet
One Year Warranty (Including battery, firmware, and software)
Certificate of Calibration and Conformance
Optional Accessories
Calibration Components, 50 Ω
ICN50B InstaCal™ Calibration Module, 38 dB, 2 MHz to 6.0 GHz, N(m), 50 Ω
OSLN50-1 Precision Open/Short/Load, N(m), 42 dB, 6.0 GHz, 50 Ω
OSLNF50-1 Precision Open/Short/Load, N(f), 42 dB, 6.0 GHz, 50 Ω
2000-1618-R Precision Open/Short/Load, 7/16 DIN(m), DC to 4.0 GHz 50 Ω
2000-1619-R Precision Open/Short/Load, 7/16 DIN(f), DC to 4.0 GHz 50 Ω
22N50 Open/Short, N(m), DC to 18 GHz, 50 Ω
22NF50 Open/Short, N(f), DC to 18 GHz, 50 Ω
SM/PL-1 Precision Load, N(m), 42 dB, 6.0 GHz
SM/PLNF-1 Precision Load, N(f), 42 dB, 6.0 GHz
Calibration Components, 75 Ω
22N75 Open/Short, N(m), DC to 3 GHz, 75 Ω
22NF75 Open/Short, N(f), DC to 3 GHz, 75 Ω
26N75A Precision Termination, N(m), DC to 3 GHz, 75 Ω
26NF75A Precision Termination, N(f), DC to 3 GHz, 75 Ω
12N50-75B Matching Pad, DC to 3 GHz, 50 Ω to 75 Ω
Phase-Stable Test Port Cables, Armored w/ Reinforced Grip (recommended for cable & antenna line sweep applications)
15RNFN50-1.5-R 1.5 m, DC to 6 GHz, N(m) to N(f), 50 Ω

15RDFN50-1.5-R 1.5 m, DC to 6 GHz, N(m) to 7/16 DIN(f), 50 Ω
15RDN50-1.5-R 1.5 m, DC to 6 GHz, N(m) to 7/16 DIN(m), 50 Ω
15RNFN50-3.0-R 3.0 m, DC to 6 GHz, N(m) to N(f), 50 Ω
15RDFN50-3.0-R 3.0 m, DC to 6 GHz, N(m) to 7/16 DIN(f), 50 Ω
15RDN50-3.0-R 3.0 m, DC to 6 GHz, N(m) to 7/16 DIN(m), 50 Ω
InterChangeable Adaptor Phase Stable Test Port Cables, Armored w/Reinforced Grip (recommended for cable and antenna line sweep applications. It
uses the same ruggedized grip as the Reinforced grip series cables. Now you can also change the adaptor interface on the grip to four different connector types)
15RCN50-1.5-R 1.5 m, DC to 6 GHz, N(m), N(f), 7/16 DIN(m), 7/16 DIN(f), 50 Ω

15RCN50-3.0-R 3.0 m, DC to 6 GHz, N(m), N(f), 7/16 DIN(m), 7/16 DIN(f), 50 Ω
Phase-Stable Test Port Cables, Armored (ideal for use with tightly spaced connectors and other general use applications)
15NNF50-1.5C 1.5 m, DC to 6 GHz, N(m) to N(f), 50 Ω
15NN50-1.5C 1.5 m, DC to 6 GHz, N(m) to N(m), 50 Ω
15NDF50-1.5C 1.5 m, DC to 6 GHz, N(m) to 7/16 DIN(f), 50 Ω
15ND50-1.5C 1.5 m, DC to 6 GHz, N(m) to 7/16 DIN(m), 50 Ω
15NNF50-3.0C 3.0 m, DC to 6 GHz, N(m) to N(f), 50 Ω
15NN50-3.0C 3.0 m, DC to 6 GHz, N(m) to N(m), 50 Ω
Page 24 of 28
Optional Accessories (continued)
Adapters
1091-26-R SMA(m) to N(m), DC to 18 GHz, 50 Ω
1091-27-R SMA(f) to N(m), DC to 18 GHz, 50 Ω
1091-80-R SMA(m) to N(f), DC to 18 GHz, 50 Ω
1091-81-R SMA(f) to N(f), DC to 18 GHz, 50 Ω
1091-172-R BNC(f) to N(m), DC to 1.3 GHz, 50 Ω
510-90 7/16 DIN(f) to N(m), DC to 7.5 GHz, 50 Ω
510-91 7/16 DIN(f) to N(f), DC to 7.5 GHz, 50 Ω
510-92 7/16 DIN(m) to N(m), DC to 7.5 GHz, 50 Ω
510-93 7/16 DIN(m) to N(f), DC to 7.5 GHz, 50 Ω
510-96 7/16 DIN(m) to 7/16 DIN (m), DC to 7.5 GHz, 50 Ω
510-97 7/16 DIN(f) to 7/16 DIN (f), DC to 7.5 GHz, 50 Ω
1091-379-R 7/16 DIN(f) to 7/16 DIN(f), DC to 6 GHz, 50 Ω, w/ Reinforced Grip
510-102-R N(m) to N(m), DC to 11 GHz, 50 Ω, 90 degrees right angle
Precision Adapters
34NN50A Precision Adapter, N(m) to N(m), DC to 18 GHz, 50 Ω
34NFNF50 Precision Adapter, N(f) to N(f), DC to 18 GHz, 50 Ω
Miscellaneous Accessories
2000-1528-R GPS Antenna, SMA(m)
69793 CW Signal Generator Kit
ODTF-1 Optical Distance-to-Fault Module, 1550 nm, Single Mode
2000-1520-R USB Flash Drive
2000-1374 External Charger for Li-lon Batteries
2300-532 Map Master CD
Backpack and Transit Case

67135 Anritsu Backpack (For Handheld Instrument and PC)
760-243-R Large Transit Case with Wheels and Handle
Directional Antennas
2000-1411-R 822 MHz to 900 MHz, N(f), 10 dBd, Yagi
2000-1413-R 1710 MHz to 1880 MHz, N(f), 10 dBd. Yagi
2000-1414-R 1850 MHz to 1990 MHz, N(f), 9.3 dBd, Yagi
2000-1519-R 500 MHz to 3 GHz, log periodic
Portable Antennas
2000-1200-R 806 MHz to 866 MHz, SMA(m), 50 Ω
2000-1473-R 870 MHz to 960 MHz, SMA(m), 50 Ω
2000-1035-R 896 MHz to 941 MHz, SMA(m), 50 Ω (1/2 wave)
2000-1474-R 1710 MHz to 1880 MHz with knuckle elbow (1/2 wave)
2000-1475-R 1920 MHz to 1980 MHz and 2110 to 2170 MHz, SMA(m), 50 Ω
2000-1361-R 2400 MHz to 2500 MHz, 5000 MHz to 6000 MHz, SMA(m), 50 Ω
2000-1636-R Antenna Kit (Consists of: 2000-1030-R, 2000-1031-R, 2000-1032-R,
2000-1200-R, 2000-1035-R, 2000-1361-R, and carrying pouch)
Page 25 of 28
Optional Accessories (continued)
Mag Mount Broadband Antenna
2000-1647-R Cable 1: 698-1200 MHz 2 dBi peak gain, 1700-2700 MHz 5 dBi peak gain,
N(m), 50 Ω, 10 ft
Cable 2: 3000-6000 MHz 5 dBi peak gain, N(m), 50 Ω, 10 ft
Cable 3: GPS 26 db gain, SMA(m), 50 Ω, 10 ft
2000-1645-R 694-894 MHz 3 dBi peak gain, 1700-2700 MHz 3dBi peak gain,
N(m), 50 Ω, 10 ft
2000-1646-R 750-1250 MHz 3 dBi peak gain, 1650-2000 MHz 5 dBi peak gain,
2100-2700 MHz 3 dBi peak gain, N(m), 50 Ω, 10 ft
2000-1648-R 1700-6000 MHz 3 dBi peak gain,N(m), 50 Ω, 10 ft
Filters
1030-114-R 806 MHz to 869 MHz, N(m) to SMA(f), 50 Ω
1030-105-R 890 MHz to 915 MHz Band, 0.41 dB loss, N(m) to SMA(f), 50 Ω
1030-149-R High Pass, 150 MHz, N(m) to N(f), 50 Ω
1030-152-R Low Pass, 200 MHz, N(m) to N(f), 50 Ω
1030-153-R Low Pass, 550 MHz, N(m) to N(f), 50 Ω
1030-155-R 2500 MHz to 2700 MHz, N(m) to N(f), 50 Ω
Attenuators
3-1010-122 20 dB, 5 W, DC to 12.4 GHz, N(m) to N(f)
42N50-20 20 dB, 5 W, DC to 18 GHz, N(m) to N(f)
42N50A-30 30 dB, 50 W, DC to 18 GHz, N(m) to N(f)
3-1010-123 30 dB, 50 W, DC to 8.5 GHz, N(m) to N(f)
1010-127-R 30 dB, 150 W, DC to 3 GHz, N(m) to N(f)
3-1010-124 40 dB, 100 W, DC to 8.5 GHz, N(m) to N(f), Uni-directional
1010-121 40 dB, 100 W, DC to 18 GHz, N(m) to N(f), Uni-directional
1010-128-R 40 dB, 150 W, DC to 3 GHz, N(m) to N(f)
T1/E1 Extender Cables

806-16-R Bantam Plug to Bantam Plug
3-806-116 Bantam Plug to BNC
3-806-117 Bantam "Y" Plug to RJ48
3-806-169 72 inch (1.8 m) BNC to BNC, 75 1/2 RG59 Type Coax Cable
806-176-R Bantam Plug to Alligator Clips
Page 26 of 28
Notes
Page 27 of 28
The Master Users Group is an organization dedicated to providing training, technical support, networking opportunities
and links to Master product development teams. As a member you will receive the Insite Quarterly Newsletter with user
stories, measurement tips, new product news and more.
Visit us to register today: www.anritsu.us/smiusignup
To receive a quote to purchase a product or order accessories visit our online ordering site: www.ShopAnritsu.com
Training at Anritsu
Anritsu has designed courses to help you stay up to date with technologies important to your job.
For available training courses visit: www.anritsu.com/training
Anritsu Corporation • Italy • India

5-1-1 Onna, Atsugi-shi, Kanagawa, 243-8555 Japan Anritsu S.p.A. Anritsu Pte. Ltd.
Phone: +81-46-223-1111 Via Elio Vittorini, 129, 00144 Roma, Italy India Branch Office
Fax: +81-46-296-1238 Phone: +39-06-509-9711 3rd Floor, Shri Lakshminarayan Niwas, #2726, 80 ft Road,
• U.S.A. Fax: +39-06-502-2425 HAL 3rd Stage, Bangalore - 560 075, India
Anritsu Company • Sweden Phone: +91-80-4058-1300
Fax: +91-80-4058-1301
1155 East Collins Boulevard, Suite 100, Anritsu AB
Richardson, TX, 75081 U.S.A. Borgafjordsgatan 13, 164 40 KISTA, Sweden • P. R. China (Hong Kong)
Toll Free: 1-800-ANRITSU (267-4878) Phone: +46-8-534-707-00 Anritsu Company Ltd.
Phone: +1-972-644-1777 Fax: +46-8-534-707-30 Units 4 & 5, 28th Floor, Greenfield Tower, Concordia Plaza,
Fax: +1-972-671-1877 No. 1 Science Museum Road, Tsim Sha Tsui East,
• Finland
• Canada Kowloon, Hong Kong, P.R. China
Anritsu AB
Anritsu Electronics Ltd. Teknobulevardi 3-5, FI-01530 VANTAA, Finland
Phone: +852-2301-4980
700 Silver Seven Road, Suite 120, Kanata, Fax: +852-2301-3545
Phone: +358-20-741-8100
Ontario K2V 1C3, Canada Fax: +358-20-741-8111 • P. R. China (Beijing)
Phone: +1-613-591-2003 Anritsu Company Ltd.
Fax: +1-613-591-1006 • Denmark
Anritsu A/S (for Service Assurance) Beijing Representative Office
• Brazil Room 2008, Beijing Fortune Building,
Anritsu AB (for Test & Measurement)
Anritsu Electrônica Ltda. No. 5 , Dong-San-Huan Bei Road,
Kirkebjerg Allé 90 DK-2605 Brøndby, Denmark Chao-Yang District, Beijing 100004, P.R. China
Praça Amadeu Amaral, 27 - 1 Andar
Phone: +45-7211-2200
01327-010 - Bela Vista - São Paulo - SP - Brasil Phone: +86-10-6590-9230
Fax: +45-7211-2210
Phone: +55-11-3283-2511 Fax: +86-10-6590-9235
Fax: +55-11-3288-6940 • Russia • Korea
• Mexico Anritsu EMEA Ltd. Anritsu Corporation, Ltd.
Anritsu Company, S.A. de C.V. Representation Office in Russia 8F Hyunjuk Bldg. 832-41, Yeoksam-Dong,
Av. Ejército Nacional No. 579 Piso 9, Col. Granada Tverskaya str. 16/2, bld. 1, 7th floor. Kangnam-ku, Seoul, 135-080, Korea
11520 México, D.F., México Russia, 125009, Moscow Phone: +82-2-553-6603
Phone: +52-55-1101-2370 Phone: +7-495-363-1694 Fax: +82-2-553-6604
Fax: +52-55-5254-3147 Fax: +7-495-935-8962
• Australia
• U.K. • United Arab Emirates Anritsu Pty Ltd.
Anritsu EMEA Ltd. Anritsu EMEA Ltd. Unit 21/270 Ferntree Gully Road, Notting Hill
200 Capability Green, Luton, Bedfordshire LU1 3LU, U.K. Dubai Liaison Office Victoria, 3168, Australia
Phone: +44-1582-433280 P O Box 500413 - Dubai Internet City Phone: +61-3-9558-8177
Fax: +44-1582-731303 Al Thuraya Building, Tower 1, Suite 701, 7th Floor Fax: +61-3-9558-8255
Dubai, United Arab Emirates • Taiwan
• France Phone: +971-4-3670352
Anritsu S.A. Fax: +971-4-3688460
Anritsu Company Inc.
12 Avenue du Québec, 7F, No. 316, Sec. 1, Neihu Rd., Taipei 114, Taiwan
• Singapore Phone: +886-2-8751-1816
Bâtiment Iris 1-Silic 638,
91140 VILLEBON SUR YVETTE, France
Anritsu Pte. Ltd. Fax: +886-2-8751-1817
Phone: +33-1-60-92-15-50 60 Alexandra Terrace, #02-08, The Comtech (Lobby A)
Fax: +33-1-64-46-10-65 Singapore 118502
Phone: +65-6282-2400
• Germany Fax: +65-6282-2533
Anritsu GmbH
Nemetschek Haus, Konrad-Zuse-Platz 1
81829 München, Germany
Phone: +49 (0) 89 44230 8-0
Fax: +49 (0) 89 442308-55
®Anritsu All trademarks are registered trademarks of 11410-00485, Rev. F Printed in United States 2010-12
their respective companies. Data subject to change ©2010 Anritsu Company. All Rights Reserved.
without notice. For the most recent specifications visit:
www.anritsu.com

MT812E - Cell Master - Anritsu

Uploaded by

Copyright:

Available Formats

MT812E - Cell Master - Anritsu

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

MT812E - Cell Master - Anritsu

Uploaded by

Copyright:

Available Formats

Technical Data Sheet

Optical Distance-to-Fault Module (P/N ODTF-1)

Fiber Type Single Mode Fiber

Optical Dynamic Range 30 dB

Optical Output Power 3 dBm, typical

Optical Connector FC/APC

Datasheet 11410-00478 (for complete specifications)

PIM Analyzer (Option 0419) (Requires PIM Master™)

2-Port Transmission Measurement (Option 0021)

Bias-Tee (Option 0010)

Interference Analyzer (Option 0025)

Application Options Bias-Tee (On/Off), Impedance (50 Ω, 75 Ω, Other)

Gated Sweep (Option 0090)

Connector Type N(m), 50 Ω Type N(m), 50 Ω Type N(m), 50 Ω Type N(m), 50 Ω

Modulation Measurements (Option 0542)

Over-the-Air (OTA) Measurements (Option 0546)

Demodulation (Option 0041) (temperature range 15 °C to 35 °C)

CPICH (dBm) Accuracy ± 0.8 dB typical

Over-the-Air (OTA) Measurements (Option 0035)

Scrambling Code Scanner Six strongest Scrambling Codes

Multipath Scanner Multipath power of six signals relative to strongest pilot

Pilot Scanner Nine strongest pilots

Multipath Scanner Multipath power of six signals relative to strongest pilot

Limit Test Average of ten tests compared to limit

Pilot Power Accuracy ± 1.0 dB typical, relative to channel power

Tau ± 0.5 µs typical, ± 1.0 µs maximum

Over-the-Air (OTA) Measurements (Option 0034)

Pilot Scanner Nine strongest pilots

Multipath Scanner Multipath power of six signals relative to strongest pilot

RF Measurements (Option 0066) (temperature range 15 °C to 35 °C)

Demodulation (Option 0067) (temperature range 15 °C to 35 °C)

Over-the-Air (OTA) Measurements (Option 0037)

ISDB-T Signal Analyzer (Option 0030)

ISDB-T SFN Analyzer (Option 0032)

E1 Bit-Error-Rate Tester (BERT) (Option 0052)

DS1 Test Mode

Master Software Tools (for your PC)

MT8212E-0021 MT8213E-0021 2-Port Transmission Measurement

MT8212E-0031 MT8213E-0031 GPS Receiver (requires Antenna P/N 2000-1528-R)

MT8212E-0025 MT8213E-0025 Interference Analyzer*

MT8212E-0431 MT8213E-0431 Coverage Mapping*

MT8212E-0090 MT8213E-0090 Gated Sweep

MT8212E-0040 MT8213E-0040 GSM/GPRS/EDGE RF Measurements

MT8212E-0044 MT8213E-0044 W-CDMA/HSDPA RF Measurements

MT8212E-0060 MT8213E-0060 TD-SCDMA/HSDPA Measurements

MT8212E-0541 MT8213E-0541 LTE RF Measurements*

MT8212E-0042 MT8213E-0042 cdmaOne/CDMA2000 1X RF Measurements

MT8212E-0062 MT8213E-0062 CDMA2000 1xEV-DO RF Measurements

MT8212E-0046 MT8213E-0046 IEEE 802.16 Fixed WiMAX RF Measurements

MT8212E-0066 MT8213E-0066 IEEE 802.16 Mobile WiMAX RF Measurements

MT8212E-0030 MT8213E-0030 ISDB-T Digital Video Measurements

MT8212E-0051 MT8213E-0051 T1 Analyzer**

MT8212E-0098 MT8213E-0098 Standard Calibration (ANSI Z540-1-1994)

10580-00250 Cell Master Instrument User Guide (Hard copy included)

10580-00241 Cable and Antenna Analyzer Measurement Guide

10580-00242 2-Port Transmission Measurement

10580-00240 Power Meter Measurement Guide

10580-00234 3GPP Signal Analyzer Measurement Guide

10580-00235 3GPP2 Signal Analyzer Measurement Guide

10580-00236 WiMAX Signal Analyzer Measurement Guide