A B C D IF IN DOUBT......PLEASE ASK!

G H J K L

7 7

A B

6 6

5 5

A B

WASHPIPE SHOWN IN TWO DIFFERENT ORIENTATIONS FOR CLARITY

SEE NOTE 1 R01 SEE NOTE 2 & 3

4 4

3 3

NOTES:

1. REFER TO ENG 60017 FOR WASHPIPE GREASING BEST PRACTICE.

2. REFER TO PN AY23899 TO ORDER ITEM R01 .

HIGH TEMPERATURE HIGH SPEED 3. INSTALL WASHPIPE ASSEMBLY, TIGHTENING UPPER AND LOWER NUT BY
2 STANDARD (HT) (HS) 2
HAND USING SUPPLIED TIGHTENING BAR, ITEM R01 .
ASSEMBLY / BOM AY25213 AY25213-HT AY25213-HS
PACKING PART # R10542 R10544 R10546 4. SEE NOTES ON SHEET 2 FOR ASSEMBLY INSTRUCTIONS. SHEET 1 OF 2
SPARE KIT PART # AY25214 AY25214-HT AY25214-HS THIRD ANGLE PROJECTION

INITIAL DESIGN
WELDING PROCEDURE AS PER CANRIG SPECIFICATION - ENG 704, UNLESS NOTED OTHERWISE
MODELED R.Belanger 2021-03-05
UNLESS OTHERWISE SPECIFIED TOLERANCE - UNLESS OTHERWISE SPECIFIED DRAWN R.Belanger 2021-03-05
DO NOT SCALE
CONFIDENTIAL AND FABRICATING [IMPERIAL] FABRICATING [METRIC] CHECKED S.Arredondo 2021-05-10
PROPRIETARY. THE
INTERPRET DRAWING PER ASME Y14.5-2009
INTERPRET CASTINGS AND FORGINGS 0 to 24" ± 1/16" 0 TO 610 mm ± 1 mm APPROVED T.York 2021-05-10 DRAWING
PER ASME Y14.8-1996 24" to 60" ± 1/8" 610 TO 1525 ± 3 mm
USE, REPRODUCTION RELEASE DATE 2021-05-12
OR DISTRIBUTION REMOVE SHARP CORNERS AND BURRS
RUN OUT .003
60 to 120"
120" to 280"
± 3/16" 1525 TO 3048 ± 5 mm
± 1/4" 3048 TO 7112 ± 7 mm REVISION
SHEET SIZED
1 WITHOUT PRIOR STRAIGHTNESS .005 IN 5 INCHES 280" & OVER ± 1/2" 7112 & OVER ± 13 mm MODELED R.Belanger 2021-05-04 1
PERPENDICULARITY .010 IN 5 INCHES
WRITTEN CONSENT PARALLELISM .010 IN 5 INCHES MACHINING [IMPERIAL] MACHINING [METRIC] WASHPIPE ASSY, 4-3 IN, 7.5K, 16 LG
.010 or as Shown DRAWN R.Belanger 2021-05-04
A INITIAL DESIGN 3498 IS PROHIBITED. ALL FLATNESS DECIMAL .x ± .030" DECIMAL x. ± .8 mm
125 .xx ± .015" x.x ± .40 mm CHECKED S.Arredondo 2021-05-10
RIGHTS RESERVED. MACHINED SURFACES .xxx ± .005" x.xx ± .13 mm APPROVED T.York 2021-05-10 EST. WEIGHT SCALE
REV REVISION DESCRIPTION ECN MIN. RADIUS UNLESS SHOWN = 0.03 MAX. ANGULAR MACHINING ± 1° FABRICATION ± 2° AY25213 REV A
REVISION RELEASE DATE 2021-05-12 97.85 lbs 1:2
A B C D IF IN DOUBT......PLEASE ASK! G H J K L
 A B C D IF IN DOUBT......PLEASE ASK! G H J K L

2
7 7

6 8 SEE NOTE 9

12B

6 SEE NOTE 8
D
12A SEE NOTES 5 & 8
6 6

11 SEE NOTES 6 & 7

7 SEE NOTE 9

SEE NOTE 9 7

C 1
11 SEE NOTES 6 & 7
5 5

1
10
10

9
9

4 SEE NOTES 5 & 8 12A 4

SECTION A-A SECTION B-B 4

SEE NOTE 8 12B 5

12B SEE NOTE 8

3 8
3 3
EXPLODED VIEW

6
4

12A SEE NOTES 5 & 8 SEE NOTES 5 & 8 12A

4

2 2
5 12 DETAIL D
SCALE 1 : 1
NOTES:
SEE NOTE 8 12B
5. DURING ASSEMBLY, HAND PACK ITEMS 12 USING GL #2 HIGH TEMPERATURE LITHIUM BASED GREASE.
UNLESS OTHERWISE SPECIFIED THIRD ANGLE PROJECTION
SEE SHEET 1 FOR DEFAULT
TOLERANCES AND
6. VERIFY SET SCREWS (ITEMS 11 ) ARE BACKED OUT BEFORE INSTALLING AND REMOVING WASHPIPE ASSEMBLY. SPECIFICATIONS

7. USING 1/4" HEX KEY, TIGHTEN SETSCREWS ON UPPER AND LOWER NUTS (ITEMS 11 ) TO APPROXIMATELY 10-15 FT-LBS. CONFIDENTIAL AND
PROPRIETARY. THE USE,
REPRODUCTION OR DO NOT SCALE DRAWING
1 8. ITEM 12 IS A KIT. IT HAS 4X ITEM 1 12A , AND 2X ITEM 12B . DISTRIBUTION WITHOUT 1
DETAIL C PRIOR WRITTEN CONSENT IS
PROHIBITED. ALL RIGHTS
WASHPIPE ASSY, 4-3 IN, 7.5K, 16 LG
9. ITEM 7 (BARREL) INCLUDES ITEM 8 (RETAINING RING).
SCALE 1 : 1 RESERVED.
SHEET 2 OF 2 AY25213 REV A
SCALE 1:2 SHEET SIZE D
A B C D IF IN DOUBT......PLEASE ASK! G H J K L