With Clamp Lever = For customers selecting MISUMI original specifications =

The products on this page are of standard specifications (Outer cylinder SUJ2 equivalent, Retainer resin). Height-adjusting Spacers for Flanged Bushings, Spacers / Stoppers for Linear Bushings
Flanged, Single/Double, Right/Left Clamp Lever Consider these specifications while selecting the product.

QFeatures: MISUMI original. The Clamp Lever Type can position workloads easier compared to the Standard. QFeatures: Bushing position can be adjusted in axial direction when space is insufficient in thrust direction.

MISUMI Original Type Outer Cylinder Balls Retainer Collar Holder Collar / Lever Screw Lever Thread Nut Ambient QHeight-adjusting Spacers
for Flanged Bushings
Type
Round Flange Square FlangeCompact Flange
M Material
Compact Flange
// 0.01 A
Right Lever Left Lever SSurface MMaterial MMaterial MMaterial SSurface MMaterial SSurface SSurface MMaterial MMaterial Operating
MMaterial HHardness MMaterial
Temp. LCSR LCSS LCSC SUS304 A
Single Double Single Double Treatment Treatment Treatment Treatment dr=6~13 dr=16~30 T±0.1
Right Lever, Single
Q Round Flange Square Flange
SUJ2 SUJ2 Plastic Aluminum Clear Electroless Zinc Baked Stainless
LHRC LHRCW LHRLC LHRLCW Equivalent 58HRC~ - Equivalent (Duracon M90 Alloy Anodize S45C Nickel Plating Diecast Paint SUS304 Steel -20~80°C

d
Equivalent) (SUS)

D
A

H
Right Lever
Single Double

W
L L P.C.D. P.C.D. F
T 2 T1 T2 T1
4-Mounting Holes Collar D+5.9 D+5.9
t t
Left Lever, Single D Unit Price
d1

d1 Part Number
d

d
P.C.D.
T Round Flange Square Flange Compact Flange
d H P.C.D. W F A
dr Selection Tolerance LCSR LCSS LCSC Height-adjusting Spacers
Type Nominal
D

D
H

T1 T3 T5 T1 T3 T5 T1 T3 T5 for Flanged Bushings

J
6 12.1 28 20 22 - 20
Nut 3.5
8 15.1 32 24 25 - 24

K
Lever Thread 10 19.1 +0.2 40 29 30 - 29
M Thread LCSR 12 21.1 0 42 32 32 - 32
1 4.5
LCSS 13 3 23.1 43 33 34 - 33
P P (G) The linear shaft is clamped by 5
the internal nut as the lever is LCSC 16 28.1 48 38 37 22 31 With Flange
rotated. 20 32.1 54 43 42 24 36 Linear Bushings
Right Lever, Double
Q +0.3 5.5
25 40.1 0 62 51 50 32 40 Shaft
Left Lever 30 45.1 6.6 74 60 58 35 49
Single Double XNot applicable to Linear Bushing Compact on P.310.

L L Part Number - T
4-Mounting Holes Collar LCSR12 - 5
T2 T1 T2 T1 LCSC25 - 3
t t
d1

d1
d

P.C.D. QFeatures: Spacers for Linear Bushing installation.

dr LBS LBSA
Left Lever, Double QSpacers for Linear Bushings Part Number L
D

D
H

Min. L ~ 40 L41~100 L101~150 Min. L ~ 40 L41~100 L101~150

1mm D d

J
Volume Volume Volume Volume Volume Volume
Unit Price Discount Rate Unit Price Discount Rate Unit Price Discount Rate Unit Price Discount Rate Unit Price Discount Rate Unit Price Discount Rate
Nut Type No. Increment
1 ~ 9 pc(s). 10~30 1 ~ 9 pc(s). 10~30 1 ~ 9 pc(s). 10~30 1 ~ 9 pc(s). 10~30 1 ~ 9 pc(s). 10~30 1 ~ 9 pc(s). 10~30
3 7 4 - - - -

K
Lever Thread
M Thread 4 8 5 - - - -
5 5~50 10 6 - - - -
P P (G) 6 12 7 - - - -
8 15 9 - - - -
10 19 11 - - - -
Type M Material S S urface Treatment 12 21 13 - - - -
LBS 13 23 14 - - - -
LBS S45C Black Oxide 6.3 25 LBSA 10~100
Part Number D Tolerance L * 16 28 17 - - - -
Eccentricity Perpendicularity LBSA 5000series Aluminum Alloy -
Tolerance No Surface Single Double H T1 T2 d d1 t P.C.D. (G) J K P M 20 32 22 - - - -
Type dr Treatment 25 40 27 - - - -
Single Double Tolerance Tolerance Single Double Single Double 30 45 32
0 0 0
16 -0.009 -0.010 28 -0.016 37 70 48 6 4.5 7.5 4.5 38 (62) 10.5 0.012 0.015 0.012 0.015 35
10~150
52 37

-0.1
-0.3
Single Double

+0.3
4 40 60 42

0
(Right Lever Type) 50
20 32 42 80 54 43 (63.2) 12.5 80 52

D
d
LHRC LHRCW 25
0 0 0 ±0.3 ±0.3 8 14 5.5 9 5.5 30 5.5 XNot applicable to Linear Bushing Compact on P.318. EFor orders larger than indicated quantity, please request a quotation.
(Left Lever Type) 25 -0.010 -0.012 40 -0.019 59 112 62 51 (70.7) 16 0.015 0.020 0.015 0.020 Part Number - L - (MC)
LHRLC LHRLCW 5 –0.1 LBSA12 - 55 - MC
30 45 64 123 74 10 6.6 11 6.1 60 (73.5) 18.5 L –0.2

* Perpendicularity of D part to flange mounting surface kgf=Nx0.101972 Part Number - L

Alteration Code Spec.
Max. Thrust Load N Basic Load Rating Allowable Static Moment Unit Price LBSA12 - 55
Mass (g) Oil Groove Machining A
2-d1Through
Oil groove is added.
dr C (Dynamic) N Co (Static) N (N • m) LHRC LHRCW

B
No. A B d1
Greased Tightening 3, 4 1.5 0.3 1
Torque N • m Single Double Single Double Single Double Single Double LHRLC LHRLCW MC 5~8 2.5 0.5 2
10~50 5 1 3
16 250 1.5 775 1230 1180 2350 - 19.7 217 289 L/2 L/2
L
20 250 1.5 882 1400 1370 2740 - 26.8 324 406 QFeatures: Retaining Plates for Linear Bushing installation.
25 250 3 980 1560 1570 3140 - 43.4 553 757 Part Number External Dimensions Mounting Hole Dimensions Reference Dimensions Mass Unit Price
QStoppers for Linear Bushings
Volume Discount Rate

30 500 3 1570 2490 2740 5490 - 82.8 683 901 Type dr D1 W H B t d P h D F G (g) 1 ~ 19 pc(s). 20~50
EFor Precautions for Use, see WP.303. EMaximum thrust load value is a reference. 5 9.6 13 12 9 10 11.5 3.5
14 6 1.0
6 11.5 14 13 1.0 10 12 15.15 3.85
8 14.3 16 15 12 15 19.65 4.35
QPrecautions for Use QMax. Thrust Load Test Method 3.4
Part Number 10 18 18 13 14 19 24.2
• For installation, loosen a lever until the nut does not  The collar is tightened to torque value(s) shown in 16 8 4.8 1.1
LHRC16 12 20 19 12.5 1.2 15 21 25.2
interfere with the shaft, then insert the shaft.
the chart, then compressive load is applied with the LMST 13 22 20 12 16 23 26.2 5.8
• Do not tighten the clamp without a shaft inserted. It may LHRC16L (L Type Greased)
cause deformation and permanent damages. tester. The compressive load where the shaft begins LHRC16G (G Type Greased) 16 27 25 15.5 20 28 30.15 6.85
• Use as an interim measure. Do not use as a permanent to move is defined as the Max. Thrust Load. LHRC16H (H Type Greased) 20 30.5 27 15 22 32 34.65 7.35
safety position holding device. * Max. thrust load of greased linear bushings was 20 1.5 4.5 10 2.5
Alternative grease types available. W 25 38 31 26 40 48.15 10.85
tested. For Days to Ship, Price and Performance, see D P.304. 14.5
t ±0.05 2–C1 2–d 30 43 34 29 45 52.4 11.6
P
XNot applicable to Linear Bushing Compact on P.318. EFor orders larger than indicated quantity, please request a quotation.
6.3
6.3

Testing Instrument Holder Linear Bushing - Standard

Shaft B Linear Bushing - Standard

H
Compression Housing Spacer for Linear Bushings

h
Collar Shaft
Linear Bushing with Clamp Lever LBS, LBSA
D1
dr

Left Lever
Shaft Stopper for Linear Bushings
0
D 1 –0.1 LMST
F G Stopper for Linear Bushings
LMST
M Material: SUS304 ∙ Stopper plates enable flexible design without regard to housing lengths.

h-1~2
∙ S topper plates allow Linear Bushings and Shafts to be installed close to
Linear Bushing with Clamp Lever
Right Lever Part Number its end face. ∙ Stopper plate can be used to hold linear
1 -329 LMST16 bushings in place.
1 -330