STRPDC-0816

TECHNICAL AND PERFORMANCE DATA

PRESSURE DROP CHARTS f WYE & BASKET STRAINERS

WYE Strainers - Small Models WYE Strainers - Large Models

Models: YS12 - YS52 - YS55 - YS56 - YS81 - YS82 Models: ACE-YI - YS58 - YS59 - YS54 - YS61 - YS62 - YS63 - YS64 - YS65

4
2

2
1 1/
1 1/

2 1/
1/4

3/8

1/2

3/4

2 1/
Sizes (in): Sizes (in):

10

12

14

16
18
20

24
1

3
10

8
2

6
10

7 7
6 6
5 5
4 4

3 3

2 2

00
0

0
0
0
110

160

110

160

260

400

570

950

160

220

330

490
610
800

110
Cv Cv Cv Cv
0.7

15

22

38

42
70

70
2

1 1

0.7 0.7
0.6
0.5 0.5
0.4 0.4

0.3 0.3

0.2 0.2

0.1 0.1
0.2 0.3 0.5 0.7 1 2 3 4 5 6 7 8 10 20 30 40 50 70 100 200 300 500 700 1000 20 30 40 50 70 100 200 300 500 700 1000 2000 3000 5000 10000 20000 50000

Legend: Pressure Drop - PSI (y - axis) versus Flow Rate - GPM (x -axis) Legend: Pressure Drop - PSI (y - axis) versus Flow Rate - GPM (x -axis)

WYE Strainers - High Pressure - Class 900 &1500 WYE Strainers - High Pressure - Class 2500
Models: YS66 - YS67 - YS68 - YS69 - YS83 - YS84 Models: YS70 - YS71 - YS85 - YS86
2-3
11 4
/2

/2
2 1/
/
1/2

Sizes (in):
11

11
Sizes (in):
10
3/

10
1

6
3

8
2

10

7 7
6 6
5 5
4 4
3 3

2 2
450

930

0
650

Cv Cv
140
180

Cv Cv
30

42

10
32

16

37

60
34
60

1
16
11
6

0.7 0.7
0.6
0.5 0.5
0.4 0.4
0.3 0.3

0.2 0.2

0.1 0.1
1 2 3 4 5 6 7 8 10 20 30 40 50 70 100 200 300 500 700 1000 2000 3000 5000 5 6 7 8 10 20 30 40 50 60 70 100 200 300 400 500 700 1000 2000

Legend: Pressure Drop - PSI (y - axis) versus Flow Rate - GPM (x -axis) Legend: Pressure Drop - PSI (y - axis) versus Flow Rate - GPM (x -axis)

Pressure Drop Equation for Liquids:

Δ P = Pressure drop (psi) G = Specific gravity of liquid Q = Flow rate (GPM)
Δ P = G × (Q / Cv)2 × Cr Cv = Flow coefficient factor Cr = Correction factor for mesh and viscosity

• These curves are theoretical; actual results may vary depending on installation conditions and other variables. Use these values for reference only.
• The above pressure drop charts are based upon 1/8" perforated screens and baskets handling clean water at 60 °F during ideal inlet and outlet conditions. Therefore, they
should only be used for estimation purposes.
• For fluids other than water, multiply the pressure drop (Δ P) obtained from the charts by the specific gravity of the fluid in question.
• For mesh lined screens, multiply the pressure drop (Δ P) obtained from the charts by the corresponding correction factor shown in the Cv correction table.

WEB: Strainer.net.au PHONE: (+61) 1300 62 4020 EMAIL: info@PRPL.com.au