Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 1 views

    c00457811

    Uploaded by

    koyuki.ku

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    c00457811

    Uploaded by

    koyuki.ku
    1 views9 pages

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    1 views9 pages

    c00457811

    Uploaded by

    koyuki.ku

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 9

    Project 2 – Magician's Hat

    Materials
    • 1 sheet of black poster board
    • 6 sheets of plain paper
    • Scissors
    • Tape
    • Glue stick

    For assembly, refer to the accompanying illustration.

    Instructions
    1. Print the hatband on plain paper. Allow to dry completely.

    2. Cut out the hatband pieces following the guides.

    3. Glue the hatband pieces together to make one long piece, then set it
    aside to dry.

    4. Print the pattern pieces on plain paper. Allow to dry completely.

    5. Cut out the pattern pieces.

    6. Assemble the three pieces of the hat’s crown along the guides by
    aligning the letters. Join them together with tape. This will create
    one hat crown pattern.

    7. Arrange the patterns on the poster board and secure each piece
    with at least two rolled pieces of tape. Be sure to leave enough
    room for the half-brim piece to flip over and form a full-circle brim.

    8. Trim around each pattern. Trim around the hat brim pattern and then
    flip it over to trim out the other half of the brim (the final brim should
    be donut-shaped). Remove the pattern pieces from the cut poster
    board and set them aside for reference.

    9. Form a tube with the hat’s crown. Make sure that it fits snugly inside
    the hole on the brim and fasten it with glue. You can use tape on the
    inside of the crown to hold it in a tube shape while the glue dries.

    10. Fold the triangular tabs on the top of the hat toward the inside of the
    hat. Fold the triangular tabs on the bottom of the hat crown toward
    the outside of the hat.
    Project 2 – Magician's Hat (continued)

    11. Rub glue on each of the outward folded bottom tabs, and then place
    the brim over the crown from the top so that it rests on top of the
    bottom tabs. Press the brim down onto the tabs and allow the glue
    to set.

    12. Put a dab of glue on each of the inward folded tabs, and then affix
    the top of the hat to the crown.

    13. Wrap the hatband around the crown so that it rests on the brim, and
    then glue it in place.

    Now your hat is finished. Just add one rabbit.


    Project 2 / Page 3
    Magician's Hat: Diagram
    Project 2 / Page 4
    Magician's Hat: Band
    Project 2 / Page 5
    Magician's Hat: Crown One

    Section 1 of Crown Pattern


    A
    Project 2 / Page 6
    Magician's Hat: Crown Two

    A
    Section 2 of Crown Pattern
    B
    Project 2 / Page 7
    Magician's Hat: Crown Three

    BSection 3 of Crown Pattern

    Glue to here
    Project 2 / Page 8
    Magician's Hat: Brim

    Hat Brim Pattern


    Project 2 / Page 9
    Magician's Hat: Top

    Hat Top Pattern

    You might also like