INCH-POUND

MIL-DTL-32372/10
5 December 2011

DETAIL SPECIFICATION SHEET

FITTING, ADAPTER, TEE, HYDRAULIC AND PNEUMATIC,

NPTF MALE ON BRANCH TO ORFS FEMALE RUN TO RUN

This specification is approved for use by all Departments

and Agencies of the Department of Defense.

The requirements for acquiring the product described herein shall consist of this specification sheet and
MIL-DTL-32372.

ORFS END (SEE SAE J1453-3)

L2 L3

T2 THREAD (SEE SAE J1453-1)

L1

SWIVEL, MANUFACTURERS
OPTION

T1 NPTF (SEE ASME B1.20.3)

NOTE: For dimensions not shown, see SAE J1453-1, SAE J1453-3 or ASME B1.20.3

Dash Tube OD T1 T2 D L1 L2 L3
size nom. NPTF ORFS Inside +/- .030 +/- .030 +/- .030
inches (mm) ASME B1.20.3 SAE J1453-1 dimension inches (mm) Inches Inches (mm)
inches (mm) (mm)
-4 .250 (6.35) 1/4 - 18 9/16 - 18 .172 +/-.003 (4.4) .780 (20) 1.04 (26.5) 1.04 (26.5)
-6 .375 (9.53) 1/4 - 18 11/16 - 16 .297 +/-.004 (7.5) 1.09 (28) 1.14 (29) 1.14 (29)
-8 .500 (12.7) 1/2 - 14 13/16 - 16 .391 +/-.004 (9.9) 1.22 (31) 1.5 (38) 1.5 (38)
-10 .625 (15.88) 1/2 - 14 1 - 14 .484 +/-.004 (12.3) 1.47 (37) 1.61 (41) 1.61 (41)
-12 .750 (19.05) 3/4 - 14 1 3/16 - 12 .609 +/-.005 (15.5) 1.59 (40) 1.83 (46.5) 1.83 (46.5)
-16 1.000 (25.40) 1 7/16 - 12 1 7/16 - 12 .844 +.007/-.005 (21.4) 1.97 (50) 2.11 (53.5) 2.11 (53.5)
-20 1.250 (31.75) 1 11/16 - 12 1 11/16 - 12 1.078 +.007/-.005 (27.4) 2.38 (60) 2.28 (58) 2.28 (58)
-24 1.500 (38.10) 1 1/2 - 11 1/2 2 - 12 1.312 +.010/-.005 (33.3) 2.64 (67) 2.4 (61) 2.4 (61)

FIGURE 1. Fittings, hydraulic and pneumatic, NPTF to ORFS, tee male to female to female adapter.
--`,`,``,`,`,``,,`,```,,,`,,`,,`-`-`,,`,,`,`,,`---

AMSC N/A FSC 4730

daneshlink.com
daneshlink.com
Provided by IHS Licensed by www.sepana.ir
No reproduction or networking permitted without license from IHS Sale for only by www.sepana.ir, 05/22/2014 00:46:31 MDT
 MIL-DTL-32372/10

NOTES:
1. Dimensions are in inches.
2. Metric equivalents are given for information only.
3. Break all sharp edges and remove all burrs and slivers.
4. Dimensions and tolerances not shown shall be in accordance with ASME B1.20.3 for NPTF end and
SAE J1453-1 for ORFS end.

FIGURE 1. Fittings, hydraulic and pneumatic, NPTF to ORFS, tee male to female to female adapter – Continued.

REQUIREMENTS

Fitting configuration and dimensions shall be as specified on figure 1.

Materials and finishes shall be in accordance with MIL-DTL-32372.

Material and Finish designators. Material and Finish designators shall be as specified in table I. All platings shall
be capable of meeting a minimum of 96 hours salt spray test in accordance with ASTM B117. The fittings shall
show no evidence of corrosion after 96 hours of salt spray. Fluid passages, other openings, and internal threads
shall not be subject to the plating thickness requirement and may have bare areas provided they are protected
with a light film of oil.

TABLE I. Material and chemical finish identification codes and chemical finish reference specifications.

Part or Identifying
Number
(PIN) code Material Plating finish
material/plating
finish
Cadmium plating in accordance with SAE AMS-C-81562, type II, class
Blank Steel
3 or SAE AMS-QQ-P-416, type II, class 2. 1/
Cadmium plating in accordance with SAE AMS-C-81562, type II, class
3 or SAE AMS-QQ-P-416, type II, class 2 with NAVAIR trivalent
CN Steel
chromium pretreatment (TCP) in accordance with
MIL-DTL-81706, type 2, class 1A.
E Steel NAVAIR TCP in accordance with MIL-DTL-81706, type 2, class 1A.
Zinc plate (finish J, P, or R) with NAVAIR TCP in accordance with
F Steel
MIL-DTL-81706, type 2, class1 A.
H Steel Aluminum-nickel in accordance with ASTM F1136, grade 3, NC.
J Steel Zinc-nickel in accordance with SAE AMS2417, type 1.
Nickel-copper alloy
M No additional finish.
UNS N04400
High-chromium nickel
N No additional finish.
alloy UNS N06690
P Steel Zinc phosphate finish in accordance MIL-DTL-16232 type Z, class1.
R Steel Zinc plating in accordance with ASTM B633; type VI, Fe/Zn 5. 2/
Corrosion resistant No additional finish. Passivation in accordance with
S
steel SAE AMS2700, type 6 or 7.
T Titanium Anodize in accordance with SAE AMS2488 type 2.
Zinc plating in accordance with ASTM B633; type II or III, Fe/Zn 5, or
Z Steel
ASTM B695, type II, class 5.
Zinc plating in accordance with ASTM B633; type II or III, Fe/Zn 5, or
ZN Steel ASTM B695, type II, class 5 with NAVAIR TCP in accordance with
MIL-DTL-81706, type 2, class 1A.
1/ Embrittlement test need not be run.
2/ Hexavalent chromium free.

--`,`,``,`,`,``,,`,```,,,`,,`,,`-`-`,,`,,`,`,,`---

daneshlink.com
daneshlink.com
Provided by IHS Licensed by www.sepana.ir
No reproduction or networking permitted without license from IHS Sale for only by www.sepana.ir, 05/22/2014 00:46:31 MDT
 MIL-DTL-32372/10

Maximum operating pressure. Maximum operating pressure shall be in accordance with

MIL-DTL-32372.

PIN: The PIN consists of the letter M, the basic specification number, the specification sheet number, a number
for fitting size, and a letter for the material finish designator.

M 32372 /10 -10 P

Material and finish code

Size
Specification sheet number
Specification number
M prefix
PIN example: M32372/10-10P indicates a tee, fitting, .625 inch tube OD, steel with zinc phosphate finish.

O-ring is not supplied. Order separately, in accordance with SAE J515.

Cadmium is not recommended. To the users of this document, it is recommended that the use of carbon steel
material with cadmium plating be used only when other materials and finishes specified in this document cannot
meet performance requirements.

Referenced documents. In addition to MIL-DTL-32372, this document references the following:

MIL-DTL-16232
MIL-DTL-81706
ASME B1.20.3
ASTM B117
ASTM B633
ASTM B695
ASTM F1136
SAE AMS-C-81562
SAE AMS-QQ-P-416
SAE AMS2417
SAE AMS2488
SAE AMS2700
SAE J1453-1
SAE J1453-3
SAE J515

--`,`,``,`,`,``,,`,```,,,`,,`,,`-`-`,,`,,`,`,,`---

daneshlink.com
daneshlink.com
Provided by IHS Licensed by www.sepana.ir
No reproduction or networking permitted without license from IHS Sale for only by www.sepana.ir, 05/22/2014 00:46:31 MDT
 MIL-DTL-32372/10

CONCLUDING MATERIAL

Custodians: Preparing activity:

Army – AR DLA – CC
Navy – SH
Air Force – 99 (Project 4730-2010-076)
DLA – CC

Review activities:
Army – AT, GL
Navy – AS, MC, SA, YD
Air Force – 71

NOTE: The activities listed above were interested in this document as of the date of this document. Since
organizations and responsibilities can change, you should verify the currency of the information above using the
ASSIST Online database at https://assist.daps.dla.mil.

--`,`,``,`,`,``,,`,```,,,`,,`,,`-`-`,,`,,`,`,,`---

daneshlink.com
daneshlink.com
Provided by IHS Licensed by www.sepana.ir
No reproduction or networking permitted without license from IHS Sale for only by www.sepana.ir, 05/22/2014 00:46:31 MDT