Philips+32PHG4900,+32PHG5000 TPM15.5L anotacoes

Colour Television Chassis
TROCA PLACA 48PFG500 POR 43PFG500 IMAGEM

VEM INVERTIDA E BORRADA NAO RESOLVEU VIA MENU
TPM15.5L
FOI RESOLVIDO RETIRANDO U6 24C128 DA PLACA DE 48 E COLOCANDO LA
NA PLACA DE 43.
ESSA MENORIA COLOCADA VIRGEM TV FICA EM STD BY
OU LIGA SEM IMAGEM
Contents Page Contents Page

1. Revision List 2
2. Technical Specs, Diversity, and Connections 2
3. Precautions, Notes, and Abbreviation List 5
4. Mechanical Instructions 9
Cable dressing (32" 4900/5000 series) 9
Cable dressing (40" & 43" 5000 series) 10
Cable dressing (48" 5000 series) 10
5. Service Modes, Error Codes, and Fault Finding 15
6. Alignments 23
7. Circuit Descriptions 25
8. IC Data Sheets 30
9. Block Diagrams
Block diagram 4900 & 5000 series 37
10. Circuit Diagrams and PWB Layouts Drawing PWB
A 715G6863 PSU 38 39-40
A 715G6934 PSU 41 43-44
A 715G6338 PSU 45 50-51
B 715G6836 SSB 52 68-69
J 715G6167 IR/LED Panel 70 71
E 715G6316 Keyboard control panel 72 73
11. Styling Sheets
4900/5000 series 32" 74
5000 series 40" & 43" 75
5000 series 48" 76
Published by YPC/CQZ/SC 1532 Quality Printed in the Netherlands Subject to modification EN 3122 785 19762
2015-Aug-08
©
2015 TP Vision Netherlands B.V.
All rights reserved. Specifications are subject to change without notice. Trademarks are the
property of Koninklijke Philips Electronics N.V. or their respective owners.
TP Vision Netherlands B.V. reserves the right to change products at any time without being obliged to adjust
earlier supplies accordingly.
PHILIPS and the PHILIPS’ Shield Emblem are used under license from Koninklijke Philips Electronics N.V.
EN 2 1. TPM15.5L LA Revision List
1. Revision List
Manual xxxx xxx xxxx.0 Manual xxxx xxx xxxx.2
• First release. • Chapter 2：Updated table 2.1 Technical Specifications
• Chapter 4：Updated figure 4-2 Cable dressing (40" & 43"
Manual xxxx xxx xxxx.1 5000 series).
• Chapter 2：Updated table 2.1 Technical Specifications • Chapter 6：Updated tables 6-2 White tone default
• Chapter 4：Updated figure 4-1 Cable dressing (32" settings and 6-3 Display code overview.
4900/5000 series). • Chapter 11: Updated styling sheet 11.2 5000 series 40" &
• Chapter 6：Updated tables 6-2 White tone default 43".
settings and 6-3 Display code overview.
• Chapter 11: Updated styling sheet 11.1 4900/5000 series
32".
2. Technical Specs, Diversity, and Connections

Index of this chapter: • Specifications are indicative (subject to change).
2.1 Technical Specifications
2.2 Directions for Use 2.1 Technical Specifications
2.3 Connections For on-line product support please use the links in back to
2.4 Chassis Overview div.table 2-1. Here is product information available, as well as
getting started, user manuals, frequently asked questions and
Notes: software & drivers.
• Figures can deviate due to the different set executions.
Table 2-1 Described Model Numbers and Diversity
2 4 9 10 11
Mechanics Schematics
E (Key board/Leading Edge)

Connection Overview
Rear Cover Removal
Stand Removal
Block Diagram
Wire Dressing
Power Supply
SSB Removal
J (IR/LED)
Styling
SSB
CTN
32PHG4900/78 2-1 4-1 4-5 4-4 4-7 9.1 10.1 10.4 10.5 10.6 11.1
32PHG5000/78 2-1 4-1 4-5 4-4 4-7 9.1 10.1 10.4 10.5 10.6 11.1
40PFG5000/78 2-1 4-2 4-5 4-4 4-7 9.1 10.2 10.4 10.5 10.6 11.2
43PFG5000/78 2-1 4-2 4-5 4-4 4-7 9.1 10.2 10.4 10.5 10.6 11.2
48PFG5000/78 2-1 4-3 4-5 4-4 4-7 9.1 10.3 10.4 10.5 10.6 11.3
2.2 Directions for Use

Directions for use can be downloaded from the following
websites:
http://www.philips.com/support
http://www.p4c.philips.com
2015-Aug-08 back to
div.table
Technical Specs, Diversity, and Connections TPM15.5L LA 2. EN 3
2.3 Connections
Rear Connectors Side Connectors
HDMI2 USB
ARC
SERV.U
HDMI1 2
5
7
TV ANTENNA
SPDIF
R
OUT
L
3
CVBS
19760_001.eps
Figure 2-1 Connection overview
Note: The following connector colour abbreviations are used 5 - Service / UART
(acc. to DIN/IEC 757): Bk= Black, Bu= Blue, Gn= Green, 1 - Ground Gnd H
Gy= Grey, Rd= Red, Wh= White, Ye= Yellow. 2 - UART_TX Transmit k
3 - UART_RX Receive j
2.3.1 Side Connections
6- HDMI 2: Digital Video - In, Digital Audio with ARC - In/Out
1 - USB2 2.0 19 1
18 2
10000_017_090121.eps
1 2 3 4 090428
10000_022_090121.eps
090121
Figure 2-3 HDMI (type A) connector
Figure 2-2 USB (type A)
1 - D2+ Data channel j
2 - Shield Gnd H
1 - +5V k
3 - D2- Data channel j
2 - Data (-) jk
3 - Data (+) jk
5 - Shield Gnd H
4 - Ground Gnd H
2- Head phone (Output) 8 - Shield Gnd H
Bk - Head phone 80 - 600 W / 10 mW 9 - D0- Data channel j
10 - CLK+ Data channel j
ot 11 - Shield Gnd H
12 - CLK- Data channel j
3 - EXT: Video YPbPr - In, Audio - In 13 - Easylink/CEC Control channel jk
Gn - Video - CBVS2 1 VPP / 75 W jq 14 - ARC Audio Return Channel k
Wh - Audio - L 0.5 VRMS / 10 kW jq 15 - DDC_SCL DDC clock j
Rd - Audio - R 0.5 VRMS / 10 kW jq 16 - DDC_SDA DDC data jk
17 - Ground Gnd H
2.3.2 Rear Connections 18 - +5V j
19 - HPD Hot Plug Detect j
4- TV ANTENNA - In 20 - Ground Gnd H
Signal input from an antenna, cable or satellite.
back to 2015-Aug-08
div.table
EN 4 2. TPM15.5L LA Technical Specs, Diversity, and Connections
7- HDMI 1: Digital Video - In, Digital Audio with ARC - In/Out 10 - CLK+ Data channel j
11 - Shield Gnd H
19 1
18 2 12 - CLK- Data channel j
10000_017_090121.eps
13 - Easylink/CEC Control channel jk
090428 14 - ARC Audio Return Channel k
15 - DDC_SCL DDC clock j
Figure 2-4 HDMI (type A) connector 16 - DDC_SDA DDC data jk
17 - Ground Gnd H
1 - D2+ Data channel j 18 - +5V j
2 - Shield Gnd H 19 - HPD Hot Plug Detect j
3 - D2- Data channel j 20 - Ground Gnd H
5 - Shield Gnd H 8 - Cinch: Digital Audio - Out
6 - D1- Data channel j BK - Coaxial 0.4 - 0.6VPP / 75 W kq
8 - Shield Gnd H
2.4 Chassis Overview

Refer to 9. Block Diagrams for PWB/CBA locations.
2015-Aug-08 back to
div.table
Precautions, Notes, and Abbreviation List TPM15.5L LA 3. EN 5
3. Precautions, Notes, and Abbreviation List

Index of this chapter: 3.3.2 Schematic Notes
3.1 Safety Instructions
3.2 Warnings • All resistor values are in ohms, and the value multiplier is
3.3 Notes often used to indicate the decimal point location (e.g. 2K2
3.4 Abbreviation List indicates 2.2 k).
• Resistor values with no multiplier may be indicated with
3.1 Safety Instructions either an “E” or an “R” (e.g. 220E or 220R indicates 220 ).
Safety regulations require the following during a repair: • All capacitor values are given in micro-farads (  10-6),
• Connect the set to the Mains/AC Power via an isolation nano-farads (n  10-9), or pico-farads (p  10-12).
transformer (> 800 VA). • Capacitor values may also use the value multiplier as the
• Replace safety components, indicated by the symbol h, decimal point indication (e.g. 2p2 indicates 2.2 pF).
only by components identical to the original ones. Any • An “asterisk” (*) indicates component usage varies. Refer
other component substitution (other than original type) may to the diversity tables for the correct values.
increase risk of fire or electrical shock hazard. • The correct component values are listed on the Philips
Spare Parts Web Portal.
Safety regulations require that after a repair, the set must be
returned in its original condition. Pay in particular attention to 3.3.3 Spare Parts
the following points:
• Route the wire trees correctly and fix them with the
For the latest spare part overview, consult your Philips Spare
mounted cable clamps.
Part web portal.
• Check the insulation of the Mains/AC Power lead for
external damage.
3.3.4 BGA (Ball Grid Array) ICs
• Check the strain relief of the Mains/AC Power cord for
proper function.
• Check the electrical DC resistance between the Mains/AC Introduction
Power plug and the secondary side (only for sets that have For more information on how to handle BGA devices, visit this
a Mains/AC Power isolated power supply): URL: http://www.atyourservice-magazine.com. Select
1. Unplug the Mains/AC Power cord and connect a wire “Magazine”, then go to “Repair downloads”. Here you will find
between the two pins of the Mains/AC Power plug. Information on how to deal with BGA-ICs.
2. Set the Mains/AC Power switch to the “on” position
(keep the Mains/AC Power cord unplugged!). BGA Temperature Profiles
3. Measure the resistance value between the pins of the For BGA-ICs, you must use the correct temperature-profile.
Mains/AC Power plug and the metal shielding of the Where applicable and available, this profile is added to the IC
tuner or the aerial connection on the set. The reading Data Sheet information section in this manual.
should be between 4.5 M and 12 M.
4. Switch “off” the set, and remove the wire between the 3.3.5 Lead-free Soldering
two pins of the Mains/AC Power plug.
• Check the cabinet for defects, to prevent touching of any Due to lead-free technology some rules have to be respected
inner parts by the customer. by the workshop during a repair:
• Use only lead-free soldering tin. If lead-free solder paste is
3.2 Warnings required, please contact the manufacturer of your soldering
• All ICs and many other semiconductors are susceptible to equipment. In general, use of solder paste within
electrostatic discharges (ESD w). Careless handling workshops should be avoided because paste is not easy to
during repair can reduce life drastically. Make sure that, store and to handle.
during repair, you are connected with the same potential as • Use only adequate solder tools applicable for lead-free
the mass of the set by a wristband with resistance. Keep soldering tin. The solder tool must be able:
components and tools also at this same potential. – To reach a solder-tip temperature of at least 400°C.
• Be careful during measurements in the high voltage – To stabilize the adjusted temperature at the solder-tip.
section. – To exchange solder-tips for different applications.
• Never replace modules or other components while the unit • Adjust your solder tool so that a temperature of around
is switched “on”. 360°C - 380°C is reached and stabilized at the solder joint.
• When you align the set, use plastic rather than metal tools. Heating time of the solder-joint should not exceed ~ 4 sec.
This will prevent any short circuits and the danger of a Avoid temperatures above 400°C, otherwise wear-out of
circuit becoming unstable. tips will increase drastically and flux-fluid will be destroyed.
To avoid wear-out of tips, switch “off” unused equipment or
3.3 Notes reduce heat.
• Mix of lead-free soldering tin/parts with leaded soldering
3.3.1 General tin/parts is possible but PHILIPS recommends strongly to
avoid mixed regimes. If this cannot be avoided, carefully
• Measure the voltages and waveforms with regard to the clear the solder-joint from old tin and re-solder with new tin.
chassis (= tuner) ground (H), or hot ground (I), depending
on the tested area of circuitry. The voltages and waveforms 3.3.6 Alternative BOM identification
shown in the diagrams are indicative. Measure them in the
Service Default Mode with a colour bar signal and stereo It should be noted that on the European Service website,
sound (L: 3 kHz, R: 1 kHz unless stated otherwise) and “Alternative BOM” is referred to as “Design variant”.
picture carrier at 475.25 MHz for PAL, or 61.25 MHz for
NTSC (channel 3). The third digit in the serial number (example:
• Where necessary, measure the waveforms and voltages AG2B0335000001) indicates the number of the alternative
with (D) and without (E) aerial signal. Measure the B.O.M. (Bill Of Materials) that has been used for producing the
voltages in the power supply section both in normal specific TV set. In general, it is possible that the same TV
operation (G) and in stand-by (F). These values are model on the market is produced with e.g. two different types
indicated by means of the appropriate symbols. of displays, coming from two different suppliers. This will then
back to 2015-Aug-08
div.table
EN 6 3. TPM15.5L LA Precautions, Notes, and Abbreviation List
result in sets which have the same CTN (Commercial Type 6 = play 16 : 9 format, 12 = play 4 : 3
Number; e.g. 28PW9515/12) but which have a different B.O.M. format
number. AARA Automatic Aspect Ratio Adaptation:
By looking at the third digit of the serial number, one can algorithm that adapts aspect ratio to
identify which B.O.M. is used for the TV set he is working with. remove horizontal black bars; keeps
If the third digit of the serial number contains the number “1” the original aspect ratio
(example: AG1B033500001), then the TV set has been ACI Automatic Channel Installation:
manufactured according to B.O.M. number 1. If the third digit is algorithm that installs TV channels
a “2” (example: AG2B0335000001), then the set has been directly from a cable network by
produced according to B.O.M. no. 2. This is important for means of a predefined TXT page
ordering the correct spare parts! ADC Analogue to Digital Converter
For the third digit, the numbers 1...9 and the characters A...Z AFC Automatic Frequency Control: control
can be used, so in total: 9 plus 26= 35 different B.O.M.s can be signal used to tune to the correct
indicated by the third digit of the serial number. frequency
AGC Automatic Gain Control: algorithm that
Identification: The bottom line of a type plate gives a 14-digit controls the video input of the feature
serial number. Digits 1 and 2 refer to the production centre (e.g. box
SN is Lysomice, RJ is Kobierzyce), digit 3 refers to the B.O.M. AM Amplitude Modulation
code, digit 4 refers to the Service version change code, digits 5 AP Asia Pacific
and 6 refer to the production year, and digits 7 and 8 refer to AR Aspect Ratio: 4 by 3 or 16 by 9
production week (in example below it is 2010 week 10 / 2010 ASF Auto Screen Fit: algorithm that adapts
week 17). The 6 last digits contain the serial number. aspect ratio to remove horizontal black
bars without discarding video
information
ATSC Advanced Television Systems
Committee, the digital TV standard in
the USA
ATV See Auto TV
Auto TV A hardware and software control
system that measures picture content,
and adapts image parameters in a
dynamic way
AV External Audio Video
AVC Audio Video Controller
AVIP Audio Video Input Processor
B/G Monochrome TV system. Sound
carrier distance is 5.5 MHz
BDS Business Display Solutions (iTV)
BLR Board-Level Repair
BTSC Broadcast Television Standard
Committee. Multiplex FM stereo sound
system, originating from the USA and
used e.g. in LATAM and AP-NTSC
10000_053_110228.eps countries
110228 B-TXT Blue TeleteXT
C Centre channel (audio)
Figure 3-1 Serial number (example) CEC Consumer Electronics Control bus:
remote control bus on HDMI
3.3.7 Board Level Repair (BLR) or Component Level Repair connections
(CLR) CL Constant Level: audio output to
connect with an external amplifier
If a board is defective, consult your repair procedure to decide CLR Component Level Repair
if the board has to be exchanged or if it should be repaired on ComPair Computer aided rePair
component level. CP Connected Planet / Copy Protection
If your repair procedure says the board should be exchanged CSM Customer Service Mode
completely, do not solder on the defective board. Otherwise, it CTI Color Transient Improvement:
cannot be returned to the O.E.M. supplier for back charging! manipulates steepness of chroma
transients
CVBS Composite Video Blanking and
3.3.8 Practical Service Precautions
Synchronization
DAC Digital to Analogue Converter
• It makes sense to avoid exposure to electrical shock. DBE Dynamic Bass Enhancement: extra
While some sources are expected to have a possible low frequency amplification
dangerous impact, others of quite high potential are of DCM Data Communication Module. Also
limited current and are sometimes held in less regard. referred to as System Card or
• Always respect voltages. While some may not be Smartcard (for iTV).
dangerous in themselves, they can cause unexpected DDC See “E-DDC”
reactions that are best avoided. Before reaching into a D/K Monochrome TV system. Sound
powered TV set, it is best to test the high voltage insulation. carrier distance is 6.5 MHz
It is easy to do, and is a good service precaution. DFI Dynamic Frame Insertion
DFU Directions For Use: owner's manual
3.4 Abbreviation List DMR Digital Media Reader: card reader
0/6/12 SCART switch control signal on A/V DMSD Digital Multi Standard Decoding
board. 0 = loop through (AUX to TV), DNM Digital Natural Motion
2015-Aug-08 back to
div.table
Precautions, Notes, and Abbreviation List TPM15.5L LA 3. EN 7
DNR Digital Noise Reduction: noise The SDI signal is self-synchronizing,

reduction feature of the set uses 8 bit or 10 bit data words, and has
DRAM Dynamic RAM a maximum data rate of 270 Mbit/s,
DRM Digital Rights Management with a minimum bandwidth of 135
DSP Digital Signal Processing MHz.
DST Dealer Service Tool: special remote iTV Institutional TeleVision; TV sets for
control designed for service hotels, hospitals etc.
technicians LS Last Status; The settings last chosen
DTCP Digital Transmission Content by the customer and read and stored
Protection; A protocol for protecting in RAM or in the NVM. They are called
digital audio/video content that is at start-up of the set to configure it
traversing a high speed serial bus, according to the customer's
such as IEEE-1394 preferences
DVB-C Digital Video Broadcast - Cable LATAM Latin America
DVB-T Digital Video Broadcast - Terrestrial LCD Liquid Crystal Display
DVD Digital Versatile Disc LED Light Emitting Diode
DVI(-d) Digital Visual Interface (d= digital only) L/L' Monochrome TV system. Sound
E-DDC Enhanced Display Data Channel carrier distance is 6.5 MHz. L' is Band
(VESA standard for communication I, L is all bands except for Band I
channel and display). Using E-DDC, LPL LG.Philips LCD (supplier)
the video source can read the EDID LS Loudspeaker
information form the display. LVDS Low Voltage Differential Signalling
EDID Extended Display Identification Data Mbps Mega bits per second
(VESA standard) M/N Monochrome TV system. Sound
EEPROM Electrically Erasable and carrier distance is 4.5 MHz
Programmable Read Only Memory MHEG Part of a set of international standards
EMI Electro Magnetic Interference related to the presentation of
EPG Electronic Program Guide multimedia information, standardised
EPLD Erasable Programmable Logic Device by the Multimedia and Hypermedia
EU Europe Experts Group. It is commonly used as
EXT EXTernal (source), entering the set by a language to describe interactive
SCART or by cinches (jacks) television services
FDS Full Dual Screen (same as FDW) MIPS Microprocessor without Interlocked
FDW Full Dual Window (same as FDS) Pipeline-Stages; A RISC-based
FLASH FLASH memory microprocessor
FM Field Memory or Frequency MOP Matrix Output Processor
Modulation MOSFET Metal Oxide Silicon Field Effect
FPGA Field-Programmable Gate Array Transistor, switching device
FTV Flat TeleVision MPEG Motion Pictures Experts Group
Gb/s Giga bits per second MPIF Multi Platform InterFace
G-TXT Green TeleteXT MUTE MUTE Line
H H_sync to the module MTV Mainstream TV: TV-mode with
HD High Definition Consumer TV features enabled (iTV)
HDD Hard Disk Drive NC Not Connected
HDCP High-bandwidth Digital Content NICAM Near Instantaneous Compounded
Protection: A “key” encoded into the Audio Multiplexing. This is a digital
HDMI/DVI signal that prevents video sound system, mainly used in Europe.
data piracy. If a source is HDCP coded NTC Negative Temperature Coefficient,
and connected via HDMI/DVI without non-linear resistor
the proper HDCP decoding, the NTSC National Television Standard
picture is put into a “snow vision” mode Committee. Color system mainly used
or changed to a low resolution. For in North America and Japan. Color
normal content distribution the source carrier NTSC M/N= 3.579545 MHz,
and the display device must be NTSC 4.43= 4.433619 MHz (this is a
enabled for HDCP “software key” VCR norm, it is not transmitted off-air)
decoding. NVM Non-Volatile Memory: IC containing
HDMI High Definition Multimedia Interface TV related data such as alignments
HP HeadPhone O/C Open Circuit
I Monochrome TV system. Sound OSD On Screen Display
carrier distance is 6.0 MHz OAD Over the Air Download. Method of
I 2C Inter IC bus software upgrade via RF transmission.
I2D Inter IC Data bus Upgrade software is broadcasted in
I2S Inter IC Sound bus TS with TV channels.
IF Intermediate Frequency OTC On screen display Teletext and
IR Infra Red Control; also called Artistic (SAA5800)
IRQ Interrupt Request P50 Project 50: communication protocol
ITU-656 The ITU Radio communication Sector between TV and peripherals
(ITU-R) is a standards body PAL Phase Alternating Line. Color system
subcommittee of the International mainly used in West Europe (colour
Telecommunication Union relating to carrier = 4.433619 MHz) and South
radio communication. ITU-656 (a.k.a. America (colour carrier
SDI), is a digitized video format used PAL M = 3.575612 MHz and
for broadcast grade video. PAL N = 3.582056 MHz)
Uncompressed digital component or PCB Printed Circuit Board (same as “PWB”)
digital composite signals can be used. PCM Pulse Code Modulation
back to 2015-Aug-08
div.table
EN 8 3. TPM15.5L LA Precautions, Notes, and Abbreviation List
PDP Plasma Display Panel SWAN Spatial temporal Weighted Averaging

PFC Power Factor Corrector (or Noise reduction
Pre-conditioner) SXGA 1280 × 1024
PIP Picture In Picture TFT Thin Film Transistor
PLL Phase Locked Loop. Used for e.g. THD Total Harmonic Distortion
FST tuning systems. The customer TMDS Transmission Minimized Differential
can give directly the desired frequency Signalling
POD Point Of Deployment: a removable TS Transport Stream
CAM module, implementing the CA TXT TeleteXT
system for a host (e.g. a TV-set) TXT-DW Dual Window with TeleteXT
POR Power On Reset, signal to reset the uP UI User Interface
PSDL Power Supply for Direct view LED uP Microprocessor
backlight with 2D-dimming UXGA 1600 × 1200 (4:3)
PSL Power Supply with integrated LED V V-sync to the module
drivers VESA Video Electronics Standards
PSLS Power Supply with integrated LED Association
drivers with added Scanning VGA 640 × 480 (4:3)
functionality VL Variable Level out: processed audio
PTC Positive Temperature Coefficient, output toward external amplifier
non-linear resistor VSB Vestigial Side Band; modulation
PWB Printed Wiring Board (same as “PCB”) method
PWM Pulse Width Modulation WYSIWYR What You See Is What You Record:
QRC Quasi Resonant Converter record selection that follows main
QTNR Quality Temporal Noise Reduction picture and sound
QVCP Quality Video Composition Processor WXGA 1280 × 768 (15:9)
RAM Random Access Memory XTAL Quartz crystal
RGB Red, Green, and Blue. The primary XGA 1024 × 768 (4:3)
color signals for TV. By mixing levels Y Luminance signal
of R, G, and B, all colors (Y/C) are Y/C Luminance (Y) and Chrominance (C)
reproduced. signal
RC Remote Control YPbPr Component video. Luminance and
RC5 / RC6 Signal protocol from the remote scaled color difference signals (B-Y
control receiver and R-Y)
RESET RESET signal YUV Component video
ROM Read Only Memory
RSDS Reduced Swing Differential Signalling
data interface
R-TXT Red TeleteXT
SAM Service Alignment Mode
S/C Short Circuit
SCART Syndicat des Constructeurs
d'Appareils Radiorécepteurs et
Téléviseurs
SCL Serial Clock I2C
SCL-F CLock Signal on Fast I2C bus
SD Standard Definition
SDA Serial Data I2C
SDA-F DAta Signal on Fast I2C bus
SDI Serial Digital Interface, see “ITU-656”
SDRAM Synchronous DRAM
SECAM SEequence Couleur Avec Mémoire.
Colour system mainly used in France
and East Europe. Colour
carriers = 4.406250 MHz and
4.250000 MHz
SIF Sound Intermediate Frequency
SMPS Switched Mode Power Supply
SoC System on Chip
SOG Sync On Green
SOPS Self Oscillating Power Supply
SPI Serial Peripheral Interface bus; a
4-wire synchronous serial data link
standard
S/PDIF Sony Philips Digital InterFace
SRAM Static RAM
SRP Service Reference Protocol
SSB Small Signal Board
SSC Spread Spectrum Clocking, used to
reduce the effects of EMI
STB Set Top Box
STBY STand-BY
SVGA 800 × 600 (4:3)
SVHS Super Video Home System
SW Software
2015-Aug-08 back to
div.table
Mechanical Instructions TPM15.5L LA 4. EN 9
4. Mechanical Instructions
Index of this chapter: Notes:
4.1 Cable Dressing • Figures below can deviate slightly from the actual situation,
4.2 Service Positions due to the different set executions.
4.3 Assembly/Panel Removal
4.4 Set Re-assembly
4.1 Cable Dressing
ECN408
CN701
CN8604 CN408
CN401
SSB
MAIN POWER SUPPLY B (1053)
A (1054)
ECN701
CN601
CN9101
(1057)
KEYBOARD CONTROL
ECN401
E
CN01
ECN408
ECN601
ECN401
ECN601
LOUDSPEAKER IR/LED BOARD

LOUDSPEAKER
J
(1184)
(1056)
(1184)
19760_100.eps
Figure 4-1 Cable dressing (32" 4900/5000 series)
back to 2015-Aug-08
div.table
EN 10 4. TPM15.5L LA Mechanical Instructions
ECN408
CN8601
CN701
CN408
MAIN POWER SUPPLY
CN403
A (1054) SSB
B (1053)
CN9101
ECN701
CN601
ECN601
ECN403
ECN408
ECN601
KEYBOARD CONTROL
E
CN01
(1057)
ECN403
LOUDSPEAKER LOUDSPEAKER
(1184) IR/LED BOARD (1184)
J (1056)
19760_101.eps
Figure 4-2 Cable dressing (40" & 43" 5000 series)
ECN701
CN8101 CN9301
ECN408
MAIN POWER SUPPLY

ECN408
A (1054)
CN701
CN408
CN403
SSB
B (1053)
CN601
ECN403
KEYBOARD CONTROL
E
CN01
(1057)
ECN601 ECN601
ECN403
LOUDSPEAKER LOUDSPEAKER
(1184) IR/LED BOARD (1184)
J (1056)
19760_102.eps
Figure 4-3 Cable dressing (48" 5000 series)
2015-Aug-08 back to
div.table
4.2 Service Positions 4.3 Assembly/Panel Removal

For easy servicing of a TV set, the set should be put face down Instructions below apply to the 32PHG5000/78, but will be
on a soft flat surface, foam buffers or other specific workshop similar for other 5000 series and 32"4900 series models.
tools. Ensure that a stable situation is created to perform
measurements and alignments. When using foam bars take 4.3.1 Stand
care that these always support the cabinet and never only the
display. Caution: Failure to follow these guidelines can
Refer to Figure 4-4 for details.
seriously damage the display!
1. Remove the fixation screws [1] that secure the stand
Ensure that ESD safe measures are taken. bracket. Refer to Figure 4-4 for details.
2. Take the stand bracket out from the set.
1 1
5 5
1 1
M4 × 16 Q3 × 8
1 5
19760_104.eps
Figure 4-4 Stand removal
4.3.2 Rear Cover
Refer to Figure 4-4 and Figure 4-5 for details.

Warning: Disconnect the mains power cord before removing
the rear cover.
1. Remove the fixation screws [2], [3] and [5] that secure the
rear cover. Refer to Figure 4-4 and Figure 4-5 for details.
2. At the indicated areas [4] the cover is secured by clips. Be
very careful with releasing those.
3. Gently lift the rear cover from the TV. Make sure that wires
and cables are not damaged while lifting the rear cover
from the set.
back to 2015-Aug-08
div.table
2 2 2 2 2
3
M3× 8
2 2
2
4 M3× 6
2 2
2 2
19760_103.eps
Figure 4-5 Rear cover removal
4.3.3 Keyboard Control Unit

1. Release the connector [2] from the keyboard control panel.
Caution: be careful, as these are very fragile connectors!
2. Remove all the fixation screws from the keyboard control
panel [1].
When defective, replace the whole unit.
2015-Aug-08 back to
div.table
1
2
19760_105.eps
Figure 4-6 Keyboard Control unit removal
4.3.4 Small Signal Board (SSB)

Caution: it is mandatory to remount all different screws at their
original position during re-assembly. Failure to do so may result
in damaging the SSB. 3 3
1. Release the clips from the LVDS connector that connect
with the SSB[1].
Caution: be careful, as these are very fragile connectors!
2. Unplug all other connectors [2] .
3. Remove all the fixation screws from the SSB [3].
4. The SSB can now be shifted from side connector cover,
then lifted and taken out of the I/O bracket. Refer to
Figure 4-7 for details. 1
2
3 3
19760_106.eps
Figure 4-7 SSB removal
4.3.5 Power Supply Unit (PSU)
Caution: it is mandatory to remount all different screws at their

original position during re-assembly. Failure to do so may result
in damaging the PSU.
1. Gently unplug all connectors from the PSU.
2. Remove all fixation screws from the PSU.
3. The PSU can be taken out of the set now.
back to 2015-Aug-08
div.table
4.3.6 Speakers
1. Gently release the tapes that secure the speaker cables.

2. Unplug the speaker connector from the SSB.
3. Take the speakers out.
When defective, replace the both units.
4.3.7 IR/LED Board
1. Remove the stand bracket as described earlier.

2. Gently release the clips that hold the board and take it out
from the bezel.
3. Unplug both the connectors from the IR/LED board.
4.3.8 LCD Panel
1. Remove the SSB as described earlier.

2. Remove the PSU as described earlier.
3. Remove the keyboard control panel as described earlier.
4. Remove the stand bracket as described earlier.
5. Remove the IR/LED as described earlier.
6. Remove the fixations screws that fix the metal clamps to
the front bezel. Take out those clamps.
7. Remove all other metal parts not belonging to the panel.
8. Lift the LCD Panel from the bezel.
4.4 Set Re-assembly

To re-assemble the whole set, execute all processes in reverse
order.
Notes:
• While re-assembling, make sure that all cables are placed
and connected in their original position. See Figure 4-1 to
Figure 4-3.
• Pay special attention not to damage the EMC foams on the
SSB shields. Ensure that EMC foams are mounted
correctly.
2015-Aug-08 back to
div.table
Service Modes, Error Codes, and Fault Finding TPM15.5L LA 5. EN 15
5. Service Modes, Error Codes, and Fault Finding

Index of this chapter: SAM in a decimal value. Every two soft-resets increase the
5.1 Test Points hour by + 1. Stand-by hours are not counted.
5.2 Service Modes
5.3 Stepwise Start-up Software Identification, Version, and Cluster
5.4 Service Tools The software ID, version, and cluster will be shown in the main
5.5 Software Upgrading menu display of SAM and CSM.
5.6 Error Codes The screen will show: “AAAAB-X.YYY”, where:
5.7 The Blinking LED Procedure • AAAA is the chassis name: TPM140L x.yy.
5.8 Fault Finding and Repair Tips • B is the region indication: E = Europe, A = AP/China, U =
NAFTA, L = LATAM.
5.1 Test Points • X is the main version number: this is updated with a major
As most signals are digital, it will be difficult to measure change of specification (incompatible with the previous
waveforms with a standard oscilloscope. However, several key software version). Numbering will go from 1 - 99 and
ICs are capable of generating test patterns, which can be AA - ZZ.
controlled via ComPair. In this way it is possible to determine - If the main version number changes, the new version
which part is defective. number is written in the NVM.
- If the main version number changes, the default settings
Perform measurements under the following conditions: are loaded.
• Service Default Mode. • YYY is the sub version number: this is updated with a minor
• Video: Colour bar signal. change (backwards compatible with the previous
• Audio: 3 kHz left, 1 kHz right. versions). Numbering will go from 000 - 999.
- If the sub version number changes, the new version
5.2 Service Modes number is written in the NVM.
The Service Mode feature is split into five parts: - If the NVM is refreshed, the software identification,
• Service Alignment Mode (SAM). version, and cluster will also be written to NVM.
• Factory Mode.
• Customer Service Mode (CSM). Display Option Code Selection
• Computer Aided Repair Mode (ComPair). When after an SSB or display exchange, the display option
code is not set properly, it will result in a TV with “no display”.
SAM and the Factory mode offer features, which can be used Therefore, it is required to set this display option code after
by the Service engineer to repair/align a TV set. Some features such a repair.
are: To do so, press the following key sequence on a standard RC
• Make alignments (e.g. White Tone), reset the error buffer transmitter: “062598” directly followed by MENU and “xxx”,
(SAM and Factory Mode). where “xxx” is a 3 digit decimal value of the panel type: see
• Display information (“SAM” indication in upper right corner column “Display Code” in back to div.table 6-3. When the value
of screen, error buffer, software version, operating hours, is accepted and stored in NVM, the set will switch to Stand-by,
options and option codes, sub menus). to indicate that the process has been completed.
During this algorithm, the NVM-content must be filtered,
because several items in the NVM are TV-related and not SSB
The CSM is a Service Mode that can be enabled by the
related (e.g. Model and Prod. S/N). Therefore, “Model”
consumer. The CSM displays diagnosis information, which the
customer can forward to the dealer or call centre. In CSM and “Prod. S/N” data is changed into “See Type Plate”. In case
a call centre or consumer reads “See Type Plate” in CSM
mode, “CSM”, is displayed in the top right corner of the screen.
mode.
The information provided in CSM and the purpose of CSM is to:
• Increase the home repair hit rate.
• Decrease the number of nuisance calls. 5.2.2 Service Alignment Mode (SAM)
• Solved customers’ problem without home visit.
Purpose
ComPair Mode is used for communication between a computer • To modify the NVM.
and a TV on I2C /UART level and can be used by a Service • To display/clear the error code buffer.
engineer to quickly diagnose the TV set by reading out error • To perform alignments.
codes, read and write in NVMs, communicate with ICs and the
micro processor (PWM, registers, etc.), and by making use of Specifications
a fault finding database. It will also be possible to up and • Operation hours counter (maximum five digits displayed).
download the software of the TV set via I2C with help of • Software version, error codes, and option settings display.
ComPair. To do this, ComPair has to be connected to the TV • Error buffer clearing.
set via the ComPair connector, which will be accessible • Option settings.
through the rear of the set (without removing the rear cover). • Software alignments (White Tone).
• NVM Editor.
Note: For the new model range, a new remote control (RC) is • Set screen mode to full screen (all content is visible).
used with some renamed buttons. This has an impact on the
activation of the Service modes. For instance the old “MENU” How to Activate SAM
button is now called “HOME” (or is indicated by a “house” icon). To activate SAM, use one of the following methods:
• Press the following key sequence on the remote control
5.2.1 General transmitter: “062596”, directly followed by the “INFO/OK”
button. Do not allow the display to time out between entries
Next items are applicable to all Service Modes or are general. while keying the sequence.
• Or via ComPair.
After entering SAM, the following items are displayed,
Life Timer
with “SAM” in the upper right corner of the screen to indicate
During the life time cycle of the TV set, a timer is kept (called
that the television is in Service Alignment Mode.
“Op. Hour”). It counts the normal operation hours (not the
Stand-by hours). The actual value of the timer is displayed in
back to 2015-Aug-08
div.table
EN 16 5. TPM15.5L LA Service Modes, Error Codes, and Fault Finding
Table 5-1 SAM mode overview
Main Menu Sub-menu 1 Sub-menu 2 Description

System Information Op Hour e.g. 00057 This represents the life timer. The timer counts normal operation hours, but does
not count Stand-by hours.
Main SW ID e.g. “TPM140L_001.145.001.000” See paragraph Software Identification, Version, and Cluster for the software name
definition.
ERR e.g. “000 000 000 000 000” Shows all errors detected since the last time the buffer was erased. Five errors
possible.
OP1 e.g. “001 224 032 000 038 137 220 Used to read-out the option bytes. See paragraph 6.4 Option Settings in the
015” Alignments section for a detailed description. Ten codes are possible.
OP2 e.g. “159 255 127 045 011 017 000
000”
Clear Codes Press [OK] to clean the Error Codes Erases the contents of the error buffer. Select this menu item and press the MENU
immediately RIGHT key on the remote control. The content of the error buffer is cleared.
Options OP#1-OP#8 e.g. “032” Option code
Alignments Warm R Gain To align the White Tone. See
G Gain paragraph 6.3 Software Alignments in the Alignments section for a detailed
description
B Gain
Normal R Gain
G Gain
B Gain
Cool R Gain
G Gain
B Gain
Store Store the RGB value
NVM editor NVM editor NVM-editor will function as in the past: Address and Value
field is a decimal value via digit entry
Service Date Edit and display the applicable service data by using the displayed key pad.
Upload to USB Channel List To upload several settings from the TV to an USB stick
NVM Copy
Readable info
EDID Copy
Download from USB Channel List To download several settings from the USB stick to the TV
NVM Copy
EDID Copy
Initialize NVM Press [OK] to Initialize NVM To initialize a (corrupted) NVM. Be careful, this will erase all settings.
immediately
How to Navigate Specifications

• In the SAM menu, select menu items with the UP/DOWN • Displaying and or changing Panel ID information.
keys on the remote control transmitter. The selected item • Displaying and or changing Tuner ID information.
will be indicated. When not all menu items fit on the screen, • Error buffer clearing.
use the UP/DOWN keys to display the next/previous menu • Various software alignment settings.
items. • Testpattern displaying.
• With the “LEFT/RIGHT” keys, it is possible to: • Public Broadcasting Service password Reset.
– (De) activate the selected menu item. • etc.
– (De) activate the selected sub menu.
– Change the value of the selected menu item. How to Activate the Factory mode
• When you press the MENU button once while in top level To activate the Factory mode, use the following method:
SAM, the set will switch to the normal user menu (with the • Press the following key sequence on the remote control
SAM mode still active in the background). transmitter: from the “menu/home” press “1999”, directly
followed by the “Back/Return” button. Do not allow the
How to Store SAM Settings display to time out between entries while keying the
To store the settings changed in SAM mode (except the sequence.
RGB Align settings), leave the top level SAM menu by using After entering the Factory mode, the following items are
the POWER button on the remote control transmitter or the displayed,
television set. The mentioned exceptions must be stored
separately via the STORE button.
How to Exit SAM

Use one of the following methods:
• Switch the set to STANDBY by pressing the mains button
on the remote control transmitter or the television set.
• Via a standard RC-transmitter, key in “00” sequence.
Note: When the TV is switched “off” by a power interrupt while
in SAM, the TV will show up in “normal operation mode” as
soon as the power is supplied again. The error buffer will not be
cleared.
5.2.3 Contents of the Factory mode:
Purpose
• To perform extended alignments.
2015-Aug-08 back to
div.table
Table 5-2 Factory mode overview
Default value
Item Item value 32" 40" 43" 48" Description
0 F/W VERSION Press OK Displays the software versions of the supplier, Flash PQ, Smart Picture, BL Dimming,
Source Meter, the Picture Quality checksum, the Dimming library, the Source meter
library, the Flash AQ, the MTK, MCU and OAD software versions.
1 PANEL_ID see back to div.table 6-3 Displays and changes the Panel ID with the left and right cursor; be careful changing
this, it can result in not correct displaying the screen!
2 ERR Code: xxx xxx xxx xxx xxx 000 000 000 000 000 Values showing the last 5 errors during the last 50 hours of operation, according to
table 5-4 Error code table
3 CLEAR ERROR BUFFER Press OK Selecting this clear all current error codes.
4 NVM ADDRESS 0 NVM address 0 to 8191, Use Item 6 to change and 7 to store the data to the correct
NVM address
5 NVM VALUE 0 Displays the value at the NVM address of item 5
6 NVM STORE Press OK Use this option to save the data of item 6 to NVM address of item 5
7 NVM COPY TV to USB Press OK Use this to store the NVM data to the REPAIR folder of a FAT formatted USB memory
stick. The TV will write two files in the REPAIR folder of the memory stick. It will create
this folder if it does not exist. The items are “Channel list”, “Personal settings”, “Option
codes”, “Display-related alignments” and “History list”. In case the download to the
USB stick was not successful “Failure” will appear. In this case, check if the USB stick
is connected properly. Now the settings are stored onto the USB stick and can be used
to download onto another TV or other SSB. Uploading is of course only possible if the
software is running and if a picture is available. This method is created to be able to
save the customer’s TV settings and to store them into another SSB.
8 NVM READ USB to TV Press OK Use this to store the NVM data from the USB memory stick to the TV. The TV will save
the two files which were created in item 8 to the NVM of the set. Use these options
when replacing a SSB. When “USB to TV Success” is displayed remove the power and
restart the TV
9 CLR_TEMP_R 128 128 128 128 Red colour temperature setting
10 CLR_TEMP_G 125 128 128 128 Green colour temperature setting
11 CLR_TEMP_B 102 128 128 128 Blue colour temperature setting
12 AUTO_COLOR Press OK PC: any pattern that has black and white, YPbPr: SMPTE bar (colour bar), any timing.
13 ADC_GAIN_R 0 Red ADC gain
14 ADC_GAIN_G 128 128 128 128 Green ADC gain
15 ADC_GAIN_B 128 128 128 128 Blue ADC gain
16 ADC_OFFSET_R 255 255 255 255 Red ADC offset
17 ADC_OFFSET_G 255 255 255 255 Green ADC offset
18 ADC_OFFSET_B 255 255 255 255 Blue ADC offset
19 VIRGING_MODE off Use this to return the set to virgin mode. Depends whether the set has been used
already.
20 E_Fuse on E-fuse mode
21 ORT_MODE off ORT mode
22 AGEING MODE off Use this for aging a new LCD panel
23 RESET_PBS_PWD Press OK Use this to reset the Child Lock
24 VIDEO_PWM_MEDIUM 0 VIDEO PWM Medium value
25 VIDEO_PWM_MINIIMUN 0 VIDEO PWM Minimum value
26 VIDEO_PWM_MAXIMUN 0 VIDEO PWM Maximum value
27 PWM_RATIO_BEST_PICTURE 0 PWM ratio best picture
28 PWM_RATIO_STD_TOP 0 PWM ratio standard top
29 PWM_RATIO_STD_BOTTOM 0 PWM ratio standard bottom
30 PWM_RATIO_BEST_POWER 0 PWM ratio best power
31 VIDEO_STD_TH_HIGH 0 VIDEO standard threshold high
32 VIDEO_STD_TH_LOW 0 VIDEO standard threshold low
33 YPBPR_PHASE InValid Not available for this chassis
34 AUD_GAIN_LINEIN 0 1 1 1 Line-in audio gain
35 AUD_GAIN_HDMI 0 0 0 0 HDMI audio gain
36 AUD_GAIN_ATV 0 0 0 0 Analogue TV audio gain
37 AUD_GAIN_DTV 0 0 0 0 Digital TV audio gain
38 AUD_GAIN_USB 0 0 0 0 USB audio gain
39 ESTICKER NVM1 0 0 0 0 ESTICKER value
back to 2015-Aug-08
div.table
Default value
Item Item value 32" 40" 43" 48" Description
59 ESTICKER RESET Press OK ESTICKER reset
60 DIM_LIB RESET Press OK Reset the Dimming
61 SRC_METER-RESET Press OK Reset the Source meter
62 AMBLIGHT RESET Press OK AMBLIGHT RESET
63 ACFG RESET Press OK REST ACFG
64 AQ_INDEX 5 5 5 6 Audio Quality index
65 AUDIO TEST MODE off Used for audio testing during production
66 AUDIO CHANNEL TYPE 2.0 Defines the installed speaker system
67 TEST PATTERN Press OK With the “left” and “right” keys of the remote control various test patterns can be chosen
68 EDID UPDATE Press OK Used to enter a new EDID codes into the NVM
69 TCON_GAMMA_UPDATE Invalid TCON gamma update
70 DUMP PQ FROM TV Press OK Saves the picture quality data to a file “pq.bin” to the root of a FAT formatted USB
memory stick
71 LOAD PQ to TV Press OK Loads the picture quality data from a file “pq.bin” in to the TV
72 DUMP AQ FROM TV Press OK Saves the audio quality data to a file “AQ.bin” to the root of a FAT formatted USB
memory stick
73 LOAD AQ to TV Press OK Loads the audio quality data from a file “AQ.bin” in to the TV
74 PANEL FLIP OFF OFF OFF OFF Flip panel
75 CVI_SOURCE OFF OFF OFF OFF Enable/Disable CVI source
76 VGA_SOURCE OFF OFF OFF OFF Enable/Disable VGA source
77 HDMI2 OFF Enable/Disable HDMI2 source
78 HDMI SIDE ON Enable/Disable HDMI SIDEsource
79 RESET_OPTION_CODE Press OK Reset Option Code
80 EXIF_FACTORY Press OK Exits the Factory mode
How to Exit the Factory mode this way, it is not necessary for the customer to look at the
Use one of the following methods: rear of the TV-set. Note that if an NVM is replaced or is
• Select EXIT_FACTORY from the menu and press the “OK” initialized after corruption, this set type has to be re-written
button. to NVM.
Note: When the TV is switched “off” by a power interrupt, or • 1.2 Production code Displays the production
normal switch to “stand-by” while in the factory mode, the TV code (the serial number) of the TV. Note that if an NVM is
will show up in “normal operation mode” as soon as the power replaced or is initialized after corruption, this production
is supplied again. The error buffer will not be cleared. code has to be re-written to NVM.
• 1.3 Installation date Indicates the date of the first
5.2.4 Customer Service Mode (CSM) installation of the TV. This date is acquired via time
extraction.
Purpose • 1.4 a Option Code 1 Gives the option codes of option
The Customer Service Mode shows error codes and group 1 as set in SAM.
information on the TVs operation settings.The call centre can • 1.4b Option Code 2 Gives the option codes of option
instruct the customer (by telephone) to enter CSM in order to group 2 as set in SAM.
identify the status of the set.This helps the call centre to • 1.5 SSB Gives an identification of the SSB as stored in
diagnose problems and failures in the TV set before making a NVM. Note that if an NVM is replaced or is initialized after
service call. corruption, this identification number has to be re-written to
The CSM is a read-only mode; therefore, modifications are not NVM. This identification number is the 12NC number of the
possible in this mode. SSB.
• 1.6 Display 12NC NVM read/write.
• 1.7 PSU 12NC NVM read/write.
Specifications
• 2.1 Current Main SW Displays the built-in main software
• Ignore “Service unfriendly modes”.
version. In case of field problems related to software,
• Line number for every
software can be upgraded. As this software is consumer
line (to make CSM language independent).
upgradeable, it will also be published on the internet.
• Set the screen mode to full
• 2.2 Standby SW Displays the built-in stand-by processor
screen (all contents on screen is visible).
software version. Upgrading this software will be possible
• After leaving the Customer Service Mode, the original
via USB.
settings are restored.
• 2.3 Panel Code Displays the Display Code number.
• Possibility to use “CH+” or “CH-” for channel surfing, or
• 2.4 Bootloader ID ID of Bootloader.
enter the specific channel number on the RC. • 2.5 NVM version Detects and displays NVM version.
• 2.6 Flash ID ID of flash model.
How to Activate CSM • 2.7 e-UM version eDFU (help) version.
To activate CSM, press the following key sequence on a • 2.8 Channel Table Structure Version version of channel
standard remote control transmitter: “123654” (do not allow the table structure.
display to time out between entries while keying the sequence). • 2.9 Error Codes Detects and displays errors.
After entering the Customer Service Mode, the following items • 3.1 Signal Quality Analog/digital signal strength.
are displayed. • 3.2 Child lock Not active / active. This is a combined item
for locks. If any lock (channel lock, parental lock) is active,it
Note: Activation of the CSM is only possible if there is no (user) is indicated as “active”.
menu on the screen! • 3.3 HDCP keys Indicates the validity of the HDMI keys (or
HDCP keys). In case these keys are not valid and the
Contents of CSM customer wants to make use of the HDMI functionality, the
• 1.1 Set Type This information is very helpful for a SSB has to be replaced.
helpdesk/workshop as reference for further diagnosis. In
2015-Aug-08 back to
div.table
How to Navigate How to Exit CSM

By means of the “CURSOR-DOWN/UP” knob (or the scroll To exit CSM, use one of the following methods.
wheel) on the RC-transmitter, can be navigated through the • Press the MENU/HOME button on the remote control
menus. transmitter.
• Press the POWER button on the remote control
transmitter.
• Press the POWER button on the television set.
5.3 Stepwise Start-up
Standby Soft Mode

Command Received,
previously in Standby Switch
Soft Mode (Power tact Off(Mains
Standby Power Plug)
switch)
Digital Digital
background background
TV Wakeup tasks started tasks completed
commands
Received
(TV Wakeup Standby
keys) commands Swith On,
Semi-
previously in
Received (RC Standby Standby/Semi-
Standby key) Standby (Mains
Power Plug)
Standby
Standby Soft Mode Soft Mode
Command Received, Command Switch Off (Mains
previously in Standby Received Power Plug)
TV Wakeup Soft Mode (Power (Power tact
commands tact switch) switch)
Received
(TV Wakeup Switch Off
keys) (Mains Power
Switch On, previously Plug)
in Power On Mode Standby Power Off
Power On (Power tact switch) Soft Mode Swith On,
previously in
Standby Soft Mode Standby Soft Mode
Command Received, (Mains Power Plug)
(Power tact switch)
Switch Off (Mains

Switch On,previously in
Power Plug)
TV Operation Mode
(Mains Power Plug)
19080_206_110323.eps
120224
Figure 5-1 Stepwise Start-up
back to 2015-Aug-08
div.table
5.4 Service Tools 5.5 Software Upgrading
5.4.1 ComPair 5.5.1 Description
Introduction It is possible for the user to upgrade the main software via the
ComPair (Computer Aided Repair) is a Service tool for Philips USB port. This allows replacement of a software image in a
Consumer Electronics products. and offers the following: stand alone set. A description on how to upgrade the main
1. ComPair helps to quickly get an understanding on how to software can be found in the DFU or on the Philips website.
repair the chassis in a short and effective way.
2. ComPair allows very detailed diagnostics and is therefore 5.5.2 Introduction
capable of accurately indicating problem areas. No
knowledge on I2C or UART commands is necessary,
Philips continuously tries to improve its products, and it’s
because ComPair takes care of this.
recommend that the TV software is updated when updates are
3. ComPair speeds up the repair time since it can available. Software update files can be obtained from the
automatically communicate with the chassis (when the
dealer or can be downloaded from the following websites:
micro processor is working) and all repair information is
http://www.philips.com/support
directly available.
4. ComPair features TV software up possibilities.
Preparing a portable memory for software upgrade
The following requirements have to be met:
Specifications
1. A personal computer connected to the internet.
ComPair consists of a Windows based fault finding program 2. An archive utility that supports the ZIP-format (e.g. WinZip
and an interface box between PC and the (defective) product.
for Windows or Stufflt for Mac OS).
The ComPair II interface box is connected to the PC via an
3. A FAT formatted USB memory stick (preferably empty).
USB cable. For the TV chassis, the ComPair interface box and
the TV communicate via a bi-directional cable via the service
Note:
connector(s).
1. Only FAT/DOS-formatted memory sticks are supported.
The ComPair fault finding program is able to determine the
problem of the defective television, by a combination of 2. Only use software update files that can be found on the
http://www.philips.com/support web site.
automatic diagnostics and an interactive question/answer
procedure.
5.5.3 Check the current TV software version
How to Connect
This is described in the chassis fault finding database in Before starting the software upgrade procedure, it is advised to
ComPair. check that what the current TV software:
1. Press the “1 2 3 6 5 4” button on the remote control to enter
TO TV
the CSM mode.
2. Use the up/down cursor keys to select “Current Main
TO TO TO
UART SERVICE
CONNECTOR
I2C SERVICE
CONNECTOR
UART SERVICE
CONNECTOR
Software”.
If the current software version of the TV is the same as the
latest update file found on http://www.philips.com/support, it is
ComPair II
Multi
function
not necessary to update the TV software.
RC in RC out
Optional Power Link/ Mode

5.5.4 Download the latest software
Switch Activity I2C RS232 /UART
1. Open the internet page http://www.philips.com/support.

2. Find information and software related to the TV.
PC
3. Select the latest software update file and download it to the
PC.
4. Insert the USB memory stick into one of the USB ports of
the PC.
5. Decompress the downloaded ZIP file and copy it to the root
ComPair II Developed by Philips Brugge directory of the USB flash drive.
Optional power
HDMI 5V DC
I2C only 5.5.5 Update the TV software
10000_036_090121.eps
091118 1. Turn the TV on and wait for it to boot completely.
2. Insert the USB memory stick that contains the software
Figure 5-2 ComPair II interface connection update files in one of the TV’s USB ports.
3. The TV will detect the USB memory stick automatically.
Caution: It is compulsory to connect the TV to the PC as Then a window jumps out as Figure 5-3.
shown in the picture above (with the ComPair interface in Note: If the USB flash drive is not detected after power up,
between), as the ComPair interface acts as a level shifter. If disconnect it and re-insert it.
one connects the TV directly to the PC (via UART), ICs can be 4. Select [Update] and press OK. See Figure 5-3.
blown! 5. To proceed, In next menu select [Start] and press OK to
start software updates. See Figure 5-4.
6. Upgrading will now begins and the status of the updating
How to Order
progress will be displayed.
ComPair II order codes:
7. When the TV software is updated. Remove your USB flash
• ComPair II interface: 3122 785 91020.
drive, then select [Restart] and press OK to restart the
• Software is available via the Philips Service web portal.
TV.See Figure 5-5.
• ComPair UART interface cable for TPM10.1x xx.
(using DB9 to 2mm pitch JST connector): 3122 785 90630.
Note: When you encounter problems, contact your local
support desk.
2015-Aug-08 back to
div.table
• FUS_clustername_version.zip: Contains the file

downloaded which is needed to upgrade the TV main
software and the software download application.
• NVM_clustername_version.zip: Default NVM content.
Must be programmed via ComPair.
5.5.7 How to Copy NVM Data to/from USB
When copying data to and from a USB memory stick, the folder
“repair” is used. When inserting an empty USB memory stick,
and downloading data to the stick, the TV will create this folder.
When sending data from a USB memory stick to a TV, the
intended data must be available in the “repair” folder.
Note that when copying EDID data to the TV, all necessary
19080_207_110324.eps
110324 EDID files must be in this folder.
Service mode overview for your reference.
Figure 5-3 Update the TV software [1/3]
Table 5-3 Service mode overview
Service Modes Description

SAM Service alignment mode
Factory Mode Used for extended alignments
CSM 3-page compact CSM pages. There will be CSM dump to
USB-stick upon entering CSM-mode
USB SW upgradeable SW-upgrading of flash memories MT5561LVNT can be
done via USB. The main SW can be upgraded via the ZIP
file downloaded.
NVM-Editor in SAM NVM-editor will function as in the past: Address and Value
field is a decimal value via digit entry
Service Data New Service data in SAM for CTN, Prod. no., 12NC
programming with virtual keyboard
USB copy/paste in Channel list, NVM data, Readable info, EDID
SAM
19080_208_110324.eps UART logging There will be printout available in UART. No specifications
110324
of the printout, per MTK provision/definition.
Blind SAM RC sequence “062598” + “Menu” +
Figure 5-4 Update the TV software [2/3] “Panel code”
Clear Buffer RC sequence “062599” + “OK” or via SAM
5.6 Error Codes
5.6.1 Introduction
Error codes are required to indicate failures in the TV set. In

principle a unique error code is available for every:
• Activated (SW) protection.
• Failing I2C device.
• General I2C error.
The last five errors, stored in the NVM, are shown in the
Service menu’s. This is called the error buffer.
The error code buffer contains all errors detected since the last
19080_209_110324.eps time the buffer was erased. The buffer is written from left to
110324
right. When an error occurs that is not yet in the error code
buffer, it is displayed at the left side and all other errors shift one
Figure 5-5 Update the TV software [3/3]
position to the right.
An error will be added to the buffer if this error differs from any
Note:
error in the buffer. The last found error is displayed on the left.
• Do not remove the USB flash drive during the software
An error with a designated error code never leads to a
update.
deadlock situation. It must always be diagnosable (e.g. error
• If a power failure occurs during the update, do not remove
buffer via OSD or blinking LED or via ComPair).
the USB flash drive from the TV. The TV will continue the
In case a failure identified by an error code automatically
software update as soon as the power comes up again.
results in other error codes (cause and effect), only the error
• If an error occurs during the update retry the procedure or
code of the MAIN failure is displayed.
contact the dealer.
• We do not recommend downgrading to an older version.
• Once the upgrade is finished, use the PC to remove the TV 5.6.2 How to Read the Error Buffer
software from the USB portable memory.
You can read the error buffer in three ways:
5.5.6 Content and Usage of the One-Zip Software File • On screen via the SAM/CSM (if you have a picture).
Example:
– ERROR: 000 000 000 000 000: No errors detected
Below you find a content explanation of the One-Zip file, and
– ERROR: 013 000 000 000 000: Error code 13 is the
instructions on how and when to use it. Only files that are
last and only detected error
relevant for Service are mentioned here.
• EDID_clustername.zip: Contains the EDID content of the
different EDID NVMs. See ComPair for further instructions.
back to 2015-Aug-08
div.table
– ERROR: 034 013 000 000 000: Error code 13 was Caution:
detected first and error code 34 is the last detected • Do not change these, without understanding the function of
(newest) error each setting, because incorrect NVM settings may
• Via the blinking LED procedure (when you have no seriously hamper the correct functioning of the TV set!
picture). See paragraph 5.7 The Blinking LED Procedure. • Always write down the existing NVM settings, before
• Via ComPair. changing the settings. This will enable you to return to the
original settings, if the new settings turn out to be incorrect.
5.6.3 Error codes
5.8.2 Load Default NVM Values
In this chassis only “layer 2” error codes are available and point
to problems on the SSB. They are triggered by LED blinking It is possible to upload the default values to the NVM with
when CSM is activated. Only the following layer 2 errors are ComPair in case the SW is changed, the NVM is replaced with
defined: a new (empty) one, or when the NVM content is corrupted.
After replacing an EEPROM (or with a defective/no EEPROM),
Table 5-4 Error code table default settings should be used to enable the set to start-up and
allow the Service Default Mode and Service Alignment Mode to
Layer-2 error code Defective device
be accessed.
13 General I2C bus error on the SSB
16 +12 V missing or low, PSU defective 5.8.3 No Picture
27 Channel decoder error on the SSB
34 Tuner I2C bus error on the SSB When you have no picture, first make sure you have entered
35 EEPROM I2C error on SSB, M24C64 the correct display code. See paragraph 6.4 Option Settings for
the instructions. See also back to div.table 6-3.
5.6.4 How to Clear the Error Buffer
5.8.4 Unstable Picture via HDMI input
The error code buffer is cleared in the following cases:
• By using the CLEAR command in the SAM menu Check (via ComPair or factory mode) if HDMI EDID data is
• By using the CLEAR command in the Factory mode: properly programmed.
• By using the following key sequence on the remote control
transmitter: “062599” directly followed by the OK button. 5.8.5 No Picture via HDMI input
• If the contents of the error buffer have not changed for 50
hours, the error buffer resets automatically. Check if HDCP key is valid. This can be done in CSM.
Note: If you exit SAM by disconnecting the mains from the 5.8.6 TV Will Not Start-up from Stand-by
television set, the error buffer is not reset.
Possible Stand-by Controller failure. Re-flash the software.
5.7 The Blinking LED Procedure
5.8.7 Audio Amplifier
5.7.1 Introduction
The Class D-IC U606 has a powerpad for cooling. When the IC
The software is capable of identifying different kinds of errors. is replaced it must be ensured that the powerpad is very well
Because it is possible that more than one error can occur over
pushed to the PWB while the solder is still liquid. This is needed
time, an error buffer is available, which is capable of storing the
to insure that the cooling is guaranteed, otherwise the Class
last five errors that occurred. This is useful if the OSD is not D-IC could break down in short time.
working properly.
Errors can also be displayed by the blinking LED procedure.
5.8.8 CSM
The method is to repeatedly let the front LED pulse with as
many pulses as the error code number, followed by a period of
1.5 seconds in which the LED is “off”. Then this sequence is When CSM is activated and there is a USB memory stick
repeated. connected to the TV, the software will dump the complete CSM
Example (1): error code 4 will result in four times the sequence content to the USB memory stick. The file (Csm.txt) will be
LED “on” for 0.25 seconds / LED “off” for 0.25 seconds. After saved in the root of the USB memory stick.
this sequence, the LED will be “off” for 1.5 seconds. Any RC
command terminates the sequence. Error code LED blinking is 5.8.9 Loudspeakers
in red color.
Make sure that the volume is set to minimum during
5.8 Fault Finding and Repair Tips disconnecting the speakers in the ON-state of the TV. The
Note: audio amplifier can be damaged by disconnecting the speakers
• It is assumed that the components are mounted correctly during ON-state of the set!
with correct values and no bad solder joints.
• Before any fault finding actions, check if the correct options 5.8.10 Display option code
are set.
Attention: In case the SSB is replaced, always check the Panel
5.8.1 NVM Editor Code in CSM, even when picture is available. Performance
with the incorrect display option code can lead to unwanted
In some cases, it can be convenient if one directly can change side-effects for certain conditions.
the NVM contents. This can be done with the “NVM Editor” in
SAM mode. With this option, single bytes can be changed.
2015-Aug-08 back to
div.table
Alignments TPM15.5L LA 6. EN 23
6. Alignments
Index of this chapter: In case you have a colour analyser:
6.1 General Alignment Conditions • Measure with a calibrated (phosphor- independent) color
6.2 Hardware Alignments analyser (e.g. Minolta CA-210) in the centre of the screen.
6.3 Software Alignments Consequently, the measurement needs to be done in a
6.4 Option Settings dark environment.
6.5 Reset of Repaired SSB • Adjust the correct x, y coordinates (while holding one of the
White point registers R, G or B on max. value) by means of
6.1 General Alignment Conditions decreasing the value of one or two other white points to the
Perform all electrical adjustments under the following correct x, y coordinates (see Table 6-1 White D alignment
conditions: values). Tolerance: dx: ± 0.003, dy: ± 0.003.
• Power supply voltage: 90 - 264 VAC, 50/ 60 ± 3 Hz. • Repeat this step for the other colour Temperatures that
• Connect the set to the mains via an isolation transformer need to be aligned.
with low internal resistance. • When finished return to the SAM root menu and press
• Allow the set to warm up for approximately 15 minutes. STANDBY on the RC to store the aligned values to the
• Measure voltages and waveforms in relation to correct NVM.
ground (e.g. measure audio signals in relation to
AUDIO_GND). Table 6-1 White D alignment values
Caution: It is not allowed to use heat sinks as ground.
• Test probe: Ri > 10 MW, Ci < 20 pF. Value Cool (11000 K) Normal (9000 K) Warm (6500 K)
• Use an isolated trimmer/screwdriver to perform x 0.276 0.287 0.313
alignments. y 0.282 0.296 0.329
6.2 Hardware Alignments If you do not have a colour analyser, you can use the default
Not applicable.
values. This is the next best solution. The default values are
average values coming from production (statistics).
6.3 Software Alignments
Put the set in SAM mode (see Chapter 5. Service Modes, Error
6.3.2 Display Adjustment
Codes, and Fault Finding). The SAM menu will now appear on
the screen. Select RGB Align and go to one of the sub menus.
The alignments are explained below. You can use the default values. The default values are average
values coming from production.
The following items can be aligned:
• Enter SAM mode.
• White point.
• Select a colour temperature (e.g. COOL, NORMAL, or
To store the data: WARM).
• Set the RED, GREEN and BLUE default values according
• Press OK on the RC before the cursor is moved to the
to the values in back to div.table 6-2.
left.
• Select “Store” and press OK on the RC. • When finished press OK on the RC, then press STORE to
store the aligned values to the NVM.
• Switch the set to stand-by mode.
• Restore the initial picture settings after the alignments.
For the next alignments, supply the following test signals via a
video generator to the RF input: Table 6-2 White tone default settings
• EU/AP-PAL models: a PAL B/G TV-signal with a signal
strength of at least 1 mV and a frequency of 475.25 MHz Colour temperature
• US/AP-NTSC models: an NTSC M/N TV-signal with a Picture mode Screen size Red Green Blue
signal strength of at least 1 mV and a frequency of Normal (9000K) 32PHG4900/78 128 97 50
61.25 MHz (channel 3). 32PHG5000/78 128 125 102
• LATAM models: an NTSC M TV-signal with a signal 40PFG5000/78 128 128 113
strength of at least 1 mV and a frequency of 43PFG5000/78 128 122 98
61.25 MHz (channel 3). 48PFG5000/78 128 123 128
Cool (11000K) 32PHG4900/78 128 120 111
6.3.1 RGB Alignment 32PHG5000/78 123 128 118

40PFG5000/78 114 128 126
43PFG5000/78 115 102 90
Before alignment, set the picture as follows:
48PFG5000/78 108 109 128
Picture Setting Warm (6500K) 32PHG4900/78 124 124 128
Dynamic backlight Off 32PHG5000/78 123 105 59
Dynamic Contrast Off 40PFG5000/78 128 118 74
Color Enhancement Off 43PFG5000/78 124 111 80
Picture Format Unscaled 48PFG5000/78 128 109 79
Light Sensor Off
Brightness 50
Color 0
This group setting of colour temperature will be applied
Contrast 100
automatically to the TV / VGA / HDMI / AV sources.
White Tone Alignment: 6.4 Option Settings

• Activate SAM.
• Select “RGB Align.” and choose a color temperature. 6.4.1 Introduction
• Use a 100% white screen as input signal and set the
following values: The microprocessor communicates with a large number of I2C
– “Red BL Offset” and “Green BL Offset” to “7” (if ICs in the set. To ensure good communication and to make
present). digital diagnosis possible, the microprocessor has to know
– All “White point” values initial to “128”.
back to 2015-Aug-08
div.table
EN 24 6. TPM15.5L LA Alignments
which ICs to address. The presence / absence of these • Select the item and press <OK> on the RC.
MT5561 ICs is made known by the option codes.
Notes:
Notes: • Only applicable to all related models that are “Smart TV
• After changing the option(s), save them by pressing the OK level 0”enabled (only YouTube access). For models
button on the RC before the cursor is moved to the left, without internet connection feature, no action is needed.
select STORE and press OK on the RC. • HDCP keys are located in the NVM. If you are loading NVM
• The new option setting is only active after the TV is with the ComPair tool, there is warning message displayed.
switched “off” / “stand-by” and “on” again with the mains
switch (the NVM is then read again). New NVM EEPROMs are shipped with pre-loaded HDCP keys.
6.4.2 Option Code Overview 6.5.2 SSB Identification
Enter SAM mode to check the option codes. they could be SSB’s of this chassis are identified by a “715” code on the SSB.
edited in the NVM. 715Axxxx-Nnn-MMM-OOOO
• 715 main category, Printed Wiring Board
6.4.3 Display Code Overview • Axxxx sub category, sequential coding number
• Nnn Version code
Press the following key sequence on a standard RC • N Development number
transmitter: “062598” directly followed by MENU and “xxx”, • nn Production number
where “xxx” is a 3 digit decimal value of the panel type: see • MMM Mounting variation code
column “Display Code” in back to div.table 6-3. After resetting • OOOO Optional variation code
the Display Code, restart the set immediately. Make sure when replacing an SSB the SSB identification codes
match the replacement panel.
Table 6-3 Display code overview
CTN_ALT BOM# Panel Type Display Code

32PHG4900/78 TPT315B5-XVN02 172
32PHG4900/78 TPT315B5-WHBN0.K S5941B 192
32PHG4900/78 TPT315B5-WX226.K S4850H 194
32PHG5000/78 TPT315B5-XVN02 172
40PFG5000/78 TPT400LA-J6PE1 SC1L 173
43PFG5000/78 TPT430H3-HVN01.U 182
43PFG5000/78 TPT430H3-DUYSHA.G S1H 191
48PFG5000/78 TPT480H2-HWU23 SC2C 174
6.5 Reset of Repaired SSB

A very important issue towards a repaired SSB from a Service
repair shop (SSB repair on component level) implies the reset
of the NVM on the SSB.
A repaired SSB in Service should get the service Set type
“00PF0000000000” and Production code “00000000000000”.
Also the virgin bit is to be set. To set all this, you can use the
ComPair tool or use the “NVM editor” and “Dealer options”
items in SAM (do not forget to “store”).
After a repaired SSB has been mounted in the set (set repair
on board level), the type number (CTN) and production code of
the TV has to be set according to the type plate of the set. For
this, you can use the NVM editor in SAM. The loading of the
CTN and production code can also be done via ComPair
(Model number programming).
In case of a display replacement, reset the “Operation hours

display” to “0”, or to the operation hours of the replacement
display.
Remark:
- After the NVM has been replaced, go to SAM and scroll to the
<Reload MAC address> (see figure 1*).
- Select the item and press <OK> on the RC.
6.5.1 Reset of Repaired SSB
Instruction
After NVM replacement, reload MAC address via SAM
menu.This ensures the correct MAC address to be available in
CSM for future repair actions.
Way of working:
• After the NVM has been replaced, go to SAM and scroll to
the <Reload MAC address> .
2015-Aug-08 back to
div.table
Circuit Descriptions TPM15.5L LA 7. EN 25
7. Circuit Descriptions
Index of this chapter: 7.1 Introduction
7.1 Introduction The TPM15.5L LA is a new chassis launched in LATAM in
7.2 Power Supply 2015. The whole range is covered by MT5561.
7.3 DC/DC Converters
The major deltas versus its predecessor support NTSC;
7.4 Front-End Analogue and DVB-T, DVB-C; ISDB-T reception
PAL-M; PAL-N AND ISDB-T with also multi-media, CEC,
7.5 HDMI
7.6 Video and Audio Processing - MT5561LVNT/B PBGA-329 ARC, SPDIF functionality.
The TPM15.5L LA chassis comes with the following stylings:

Notes:
• series xxPHG4900xx
• Only new circuits (circuits that are not published recently)
• series xxPHG5000xx
are described.
• series xxPFG5000xx
• Figures can deviate slightly from the actual situation, due
to different set executions.
• For a good understanding of the following circuit 7.1.1 Implementation
descriptions, please use the wiring, block (see chapter
9. Block Diagrams) and circuit diagrams (see chapter Key components of this chassis are:
10. Circuit Diagrams and PWB Layouts).Where necessary, • SCALER MT5561LVNT/B PBGA-329
you will find a separate drawing for clarification. • Silicon Tuner MxL661-AG-R
• DEMODULATOR TC90537FG LQFP-48
• AUDIO TAS5729MDDCAR 10W TSSOP-48 for Audio
Amplifier
7.1.2 TPM15.5L LA Architecture Overview
For details about the chassis block diagrams refer

to 9. Block Diagrams. An overview architecture can be found in
Figure 9.1.
back to 2015-Aug-08
div.table
EN 26 7. TPM15.5L LA Circuit Descriptions
7.1.3 SSB Cell Layout
DC/DC
USB
DDR HDMI
MT5561
Headphone
ANALOG I/O
SERVICE
CONNECTOR
TUNER
HDMI
SPDIF
OUT
19760_200.eps
Figure 7-1 SSB layout cells (top view)
2015-Aug-08 back to
div.table
7.2 Power Supply

Refer to figure Figure 7-2 for the power architecture of this
platform.
CN8604(FOR 715G6863) AMP LVDS AMP

CN8601(FOR 715G6934)
CN8101(FOR 715G6338)
12V 12V
Platform power
BL-ON/OFF
DIM
Display power 12V
Platform
12V-Audio
MTK5561
CN701
Low stby
power
PFC Ac-input + Mains filter

AC IN 1 power- PCB
CN9901
19760_201.eps
Figure 7-2 Power Architecture
7.2.1 Power Supply Unit 7.2.2 Diversity
All power supplies are a black box for Service. When defective, The diversity in power supply units is mainly determined by the
a new board must be ordered and the defective one must be diversity in displays.
returned, unless the main fuse of the board is broken. Always
replace a defective fuse with one with the correct The following displays can be distinguished:
specifications! This part is available in the regular market. • CCFL/EEFL backlight: power panel is conventional IPB
Consult the Philips Service web portal for the order codes of the • LED backlight:
boards. - side-view LED without scanning: PSL power panel
- side-view LED with scanning: PSLS power panel
Important delta’s with the TPM15.5L LA classis platform are: - direct-view LED without 2D-dimming: PSL power panel
• New power architecture for LED backlight - direct-view LED with 2D-dimming: PSDL power panel.
• “Boost”-signal is now a PWM-signal + continuous variable.
PSL stands for Power Supply with integrated LED-drivers.
The control signals are: PSLS stands for a Power Supply with integrated LED-drivers
• Stand-by with added Scanning functionality (added microcontroller).
• Lamp “on/off” PSDL stands for a Power Supply for Direct-view LED backlight
• DIM (PWM) (not for PSDL) with 2D-dimming.
In this manual, no detailed information is available because of

design protection issues.
The output voltages to the chassis are:

• +12V (Stand-by mode only)
• +12V (on-mode)
• +Vsnd (+12V) (audio power) (on-mode)
• +12V (bolt-on power) (on-mode)
• +22V (bolt-on power) (on-mode,Stand-by mode) for
40PFG5000/78)
• +16V (bolt-on power) (on-mode,Stand-by mode) for
32PHG5000/78
• Output to the display; in case of
- IPB: High voltage to the LCD panel
- PSL and PSLS (LED-driver outputs)
- PSDL (high frequent) AC-current.
back to 2015-Aug-08
div.table
EN 28 7. TPM15.5L LA Circuit Descriptions
7.2.3 Connector overview
Table 7-1 Connector overview
Connector
32" 40" & 43" 48"
Number CN9101 CN8604 CN9101 CN8601 CN9301 CN8101
Description to SSB to Panel to SSB to panel to SSB to panel
Pin 14 6 16 12 14 12
1 DIM VLED+ DIM VLED+ DIM VLED+
2 On/off VLED+ On/off n.c. On/off n.c.
3 PS_ON n.c. PS_ON VLED- PS_ON VLED_1
4 Scan_BL_EN n.c. n.c. VLED- 2D/3D VLED_1
5 GND LED_a GND n.c. GND- n.c.
6 GND LED_a GND n.c. GND n.c.
7 GND - GND n.c. GND n.c.
8 GND - GND n.c. GND n.c.
9 +12V-AUDIO - +12V-AUDIO VLED- +12V-AUDIO VLED_2
10 +12V-AUDIO - +12V-AUDIO VLED- +12V-AUDIO VLED_2
11 +12V - +12V n.c. +12V n.c.
12 +12V - +12V VLED+ +12V VLED+
13 +12V_AL - +12V - +12V -
14 +12V_AL - +12V - +12V -
15 - - +5V - - -
16 - - +5V - - -
7.3 DC/DC Converters • +3V3, genenal supply voltage

The on-board DC/DC converters deliver the following voltages • +3V3-TUN, supply voltage for tuner
(depending on set execution): • +5V-USB, input intermediate supply voltage for the USB
• +5V-STANDBY, permanent voltage for the Stand-by Power
controller, LED/IR receiver and controls. • +3V3, from the power supply for the scaler IC MT5561
• +3V3, supply voltage for Keyboard • +1.1V, clean voltage for Demod channel decoder
• +12V, input from the power supply for the panel
common(active mode) Figures gives a graphical representation of the DC/DC
• +12V, input from the power supply for the AMP converters with its current consumptions :
• +1V2, from the power supply for the scaler IC MT5561
• +1V5, supply voltage for DDR2 ( diagram B03B)
+12V_AMP +12VSB_PRE
R719
AVDD1V2 (1.2V)
U706 +5V_SB U703
FB703 FB702
+12V SY8104ADC M5723B-33F61U VCCK (1.2V)
U702 +3.3V_SB
FB403
G903T63UF VCC3.3VA_A1
FB413
AVDD_DMPLL
FB414
AVDD_AU
FB601
PVDD_R
U601
AD87588 FB504 U503
FB602 G529A1TP1U MHL
PVDD_L
5V_Normal U116
Q701
APL3511 Wi-Fi_VCC
AO3401A
U705
G5695T11U DVDD3V3
AVDD3V3
19760_202.eps
2015-Aug-08 back to
div.table
Figure 7-3 DC/DC converters
7.4 Front-End Analogue and DVB-T, DVB-C; 7.5 HDMI

ISDB-T reception Refer to figure 7-6 HDMI input configuration for the application.
7.4.1 Front-End Analogue part
The Front-End for analogue tuner consist of the following key

components: MTK5561 RX
I2C
• Silicon Tuner MxL661-AG-R (NTSC,PAL-M, PAL-N and
ISDB-T)
• SCALER MT5561LVNT/B PBGA-329
I2C CN501
Below find a block diagram of the front-end application for RX
analogue part. REAR HDMI
MxL661-AG-R CN502
I2C HDMI Side
I2C
19760_205.eps
IF
IF_AGC
IF_AGC Figure 7-6 HDMI input configuration
RF_AGC The following HDMI connector can be used:

X
MTK5561
• HDMI 1: HDMI input ( TV digital interface support HDCP)
RF_AGC
with digital audio/PC DVI input/ARC
• Rear HDMI: HDMI input ( TV digital interface support
HDCP) with digital audio/PC DVI input
19760_203.eps
• +5V detection mechanism
• Stable clock detection mechanism
Figure 7-4 Front-End Analogue block diagram • Embedded EDID
• HPD control
7.4.2 DTV part • Sync detection
• TMDS output control
The Front-End for DVT part consist of the following key • CEC control
components:
7.6 Video and Audio Processing - MT5561LVNT/B
• Silicon Tuner MxL661-AG-R (NTSC,PAL-M, PAL-N and PBGA-329
ISDB-T) The MT5561LVNT/B is the main audio and video processor (or
• SCALER MT5561LVNT/B PBGA-329 System-on-Chip) for this platform. It has the following features:
• DEMODULATOR TC90537FG LQFP-48
• Multi-standard digital video decoder (MPEG 1-2, H.264,
Below find a block diagram of the front-end application for DTV MPEG-4)
part. • A transport de-multiplexer
• A muti-standard video decoder
• Rich format audio codec
MxL661-AG-R
• HDMI 1.4a receiver with 3D support
I2C • 2D/3D converter
I2C
• Local dimming (LED backlight)(0ption)
IF • Panel overdrive control
TC90537FG • Two-link LVDS
IF-AGC LQFP-48
IF_AGC
The MT5561LVNT/B combines front-end video processing
RF_AGC TS DATA functions, such as ATSC,DVB-T/T2,DVB-C,DVB-S2 channel
decoding, MPEG 1-2/H.264 decode, analog video decode and
RF_AGC X MTK5561
HDMI reception, with advanced back-end video picture
improvements. It also includes next generation Motion Accurate
Picture Processing High flat panel screen resolutions and
19760_204.eps refresh rates are supported with formats including 1360 × 768
@ 60Hz and 1920 x 1080 @ 60Hz.It integrates high-quality
Figure 7-5 Front-End DVB-T2 DTV block diagram HDMI 1.4a, USB 2.0 receiver, Ethernet MAC+PHY, Single core
CPU. Professional error-concealment provides stable, smooth
and mosaic-free video quality
For a functional diagram of the MT5561LVNT/B, refer

to Figure 8-1.
back to 2015-Aug-08
div.table
EN 30 8. TPM15.5L LA IC Data Sheets
8. IC Data Sheets
This chapter shows the internal block diagrams and pin
configurations of ICs that are drawn as “black boxes” in the
electrical diagrams (with the exception of “memory” and “logic”
ICs).
8.1 Diagram 10-4-2 Peripheral, B02, MT5561LVNT (IC U401B)
Block diagram
MT5561LVNT
TS
Input
TS JPEG/MP2/MP4/ LVDS/min-LVS/
Demux DivX/H.264/VC-1/ EPI
Demod Panel
RM/AVS/VP8 OD, TCON
Decoders (option) (option)
Tuner
Input
NTSC/
PAL/ 2D/3D Converter
SECAM De- Vplane
Post Processing
ATD interlace scaler
(option)
TV
Decoder
CVBS/YC
Input Video Video OSD
Grapihc
Component ADC Input scaler
Analog Input
HDMI HDMI Rx
Input/
MHL MHL Rx
Audio SPDIF Out, I2S

SIF ADAC L/R x 2
Demod Audio
Audio DSP Audio DAC
I/F
Audio Audio
ADC Input
Audio
Input 16-bit
ARM DDR3 Embedded
SPDIF Controller DDR3
In
JTAG IrDA I2C USB2.0 PWM Watchdog Serial Flash Servo ADC T8032
Smart
PCR RTC UART SDIO Ethernet NAND Flash
Card
19620_300_140111.eps
140111
Figure 8-1 Internal block diagram
2015-Aug-08 back to
div.table
IC Data Sheets TPM15.5L LA 8. EN 31
Pinning Information
MT5561LVNT
DVSS AO0P AOCKP AE1P DVSS CI_A3
GPIO0 AO0N AOCKN AE1N CI_D0 CI_REG#
TCON4 TCON2 AO1P AO2P AO3P AE0P AE2P AE3P CI_A1 CI_MOVAL
TCON5 TCON7 AO1N AO2N AO3N AE0N AE2N AE3N CI_A0 CI_A4
TCON3 TCON0 GPIO1 OPWM0 CI_MDO1 CI_MDO2 CI_A12 CI_A5
TCON8 TCON1 TCON6 OSCL1 OSDA1 DVSS CI_CD2# CI_D2 CI_A2
PDD6 PDD0 PDD3 PDD1 OPWM1 OPWM2 DVSS DVSS
PDD4 GPIO4 GPIO3 DVSS DVSS
POOE
POCE1# PDD7 POCE0# POWE# PDD5 DVSS VCCK DVSS
#
PACLE PAALE PDD2 PARB# VCCK VCCK VCCK VCCK DVSS DVSS
VCCK VCCK VCCK VCCK VCCK VCCK VCCK VCCK DVSS DVSS
DVSS DVSS DVSS DVSS DVSS DVSS VCCK VCCK DVSS DVSS
DDRV DDRV DDRV DDRV DDRV DDRV DVSS DVSS DVSS VCC3IO
DDRV AOLRC
ZQ OSDA0 DVSS ADIN1 VCC3IO VCC3IO
REF K
AOBC AOSDAT ASPDIF AVDD33_E AVDD33_HD
AOMCLK OSCL0 DVSS ADIN7
K A0 O TH MI
AOSDAT
OPWRSB OIRI DVSS ADIN6 ADIN0 ADIN4
A1
OPCTRL OPCTRL HDMI_0_R
U0TX U0RX ADIN5 ADIN3 HDMI_0_SCL ADIN2 HSYNC
0 4 X_1B
OPCT OPCTRL VGA_SD HDMI_0_S HDMI_0_RX_ HDMI_0_R
OPCTRL1 VGA_SCL HDMI_0_RX_0 VSYNC
RL3 2 A DA 0B X_1
REXT_E HDMI_0_RX_ HDMI_0_R
RXVN RXVP HDMI_0_HPD ORESETB
TH CB X_2B
AVDD12 AVDD12_HDM HDMI_0_RX_ HDMI_0_R AVDD10_LD
TXVN TXVP DVSS
_ETH I_0 C X_2 O
19620_301_140111.eps
140111
Figure 8-2 Internal pin configuration [1/2]
back to 2015-Aug-08
div.table
Pinning Information
MT5561LVNT
CI_MCLKO CI_MDI4 CI_A14 CI_MDI0 CI_IORD# CI_A10 FSRC_WR
CI_A6 CI_MIVAL CI_WE# CI_A13 CI_A11 CI_CE1# CI_D7
CI_WAIT# CI_RESET CI_MDI3 CI_MDI2 CI_MDI1 CI_A8 CI_A9 CI_OE# CI_MDO7 CI_MDO6
CI_MOSTRT CI_A7 CI_D1 CI_MCLKI CI_MISTRT CI_IOWR# CI_D6 CI_MDO5 CI_D5
CI_MDO0 CI_MDI5 CI_MDI7 CI_MDO3 CI_D3 CI_CD1# CI_D4 CI_MDO4
CI_IREQ# CI_MDI6 ASPDIFI GPIO5 CI_PWR_EN USB_DP1 DVSS
GPIO2 DVSS USB_DM1
DVSS DVSS DVSS DVSS DVSS USB_DP0 USB_DM0 AVDD12_HDMI_1
DVSS DVSS DVSS HDMI_2_SDA IF_AGC HDMI_2_HPD_CBUS HDMI_2_SCL HDMI_1_SCL HDMI_2_RX_2 HDMI_2_RX_2B
DVSS DVSS HDMI_1_SDA MHL_SENCE HDMI_CEC HDMI_2_RX_0 HDMI_2_RX_1 HDMI_2_RX_1B
DVSS DVSS DVSS AVDD33_CAP RF_AGC HDMI_1_HPD HDMI_2_RX_0B
DVSS DVSS DVSS AVDD33_AADC AVDD33_ADAC HDMI_2_RX_C HDMI_2_RX_CB HDMI_1_RX_2 HDMI_1_RX_2B
DVSS DVSS DVSS AVSS33_CLN DVSS DVSS HDMI_1_RX_1 HDMI_1_RX_1B
DVSS DVSS DVSS AR0_ADAC HDMI_1_RX_0 HDMI_1_RX_0B HDMI_1_RX_C HDMI_1_RX_CB
DVSS DVSS DVSS DVSS AL0_ADAC AIN_R1 AIN_R3 AIN_R2 AIN_R0
AVSS33_RGB DVSS AVSS33_VIDEO DVSS VMID_AADC AVDD33_REG_STB AL1_ADAC AIN_L3 AIN_L2
SOG SOY1 COM1 Y0 PB0 DVSS AVDD33_VIDEO_STB AR1_ADAC AIN_L0
BP RP Y1 SOY0 COM0 DVSS AVDD33_RGB_STB CVBS0 XTALI AIN_L1
GP PB1 PR0 VDAC_OUT ADCINP_DEMOD DVSS XTALO
COM PR1 CVBS_COM CVBS1 ADCINN_DEMOD AVDD12_DEMOD
19620_303_140111.eps
140111
Figure 8-3 Internal pin configuration [2/2]
2015-Aug-08 back to
div.table
8.2 Diagram 10-4-1 System Power B01, M5723B (IC U703)
Block diagram
IN1
Current Sense
M5723B OC
+
OSC
HDRV
VREF
100mΩ
0.6V + S
+ A1 R Q
EA LX
CONTROL
FB1
LDRV
UVLO 80mΩ
Compensation
Thermal
Shutdown PGND
Zero Current Detect
EN1
IN2
EN2
炼
OVER CURRENT
ERROR PROTECT & DYNAMIC
AMP FEEDBACK
SHUTDOWN
為
LOGIC OUT2
R1
OVER TEMP. 1.25V
PROTECT Vref
R2
AGND
Pinning information
EN1 1 10 LX
AGND 2 9 PGND
Thermal
FB1 3 Pad 8 IN1
AGND 4 7 OUT2
EN2 5 6 IN2
19760_300.eps
Figure 8-4 Internal block diagram and pin configuration
back to 2015-Aug-08
div.table
8.3 Diagram 10-4-4 Speaker Amp B04, TAS5729MDDCAR (IC U601)
Block diagram
TAS5729MD
DVDD AVDD ANA_REG1 ANA_REG2 DIG_REG DRVDD DR_CN DR_CP DRVSS PVDD GVDD_REG
Analog Supply Gate Drive

Regulators Regulator
Charge Pump
Digital Supply Regulator
PWM Power Stage
Digital Audio Processor Full Bridge

SPK_OUTA
Gate Power
MCLK Digital Equalizer, Two-Band
Serial Open Loop Drives Stage A
SCLK AGL, Coarse/Fine Volume Over- SPK_OUTB
Audio Digital PWM
LRCLK
Control, THD Manager, PWM Current
SDIN
Port Modulator Gate SPK_OUTC
Level Meter Full Bridge Protection
Drives
Power
SPK_OUTD
Stage B
Clock
Monitoring
Stereo HP / Line Driver Die Temp. Monitor
DRVDD
DR_INA DR_INx
- DR_OUTA
DR_INB DR_OUTx DR_OUTB
+
DRVSS
Internal Control Registers and State Machines
ADR / SPK_FAULT DR_SDI PDN RST SCL SDA
Pinning information
PGND 1 48 SPK_OUTB
SPK_OUTA 2 47 BSTRPB
BSTRPA 3 46 BSTRPC
PVDD 4 45 SPK_OUTC
TEST1 5 44 PGND
TEST2 6 43 SPK_OUTD
DR_INA 7 42 BSTRPD
DR_OUTA 8 41 PVDD
DR_OUTB 9 40 GVDD_REG
DR_INB 10 39 DR_SDI
DRVSS 11 38 SSTIMER
DR_CN 12 37 ANA_REG2
DR_CP 13 36 AGND
DRVDD 14 35 DGND
PLL_GND 15 34 DVDD
PLL_FLTM 16 33 TEST3
PLL_FLTP 17 32 RST
ANA_REG1 18 31 NC
Thermal Pad
AVDD 19 30 SCL
ADR / SPK_FAULT 20 29 SDA
MCLK 21 28 SDIN
OSC_RES 22 27 SCLK
OSC_GND 23 26 LRCLK
DIG_REG 24 25 PDN
19690_301.eps
2015-Aug-08 back to
div.table
8.4 Diagram 10-4-9 TUNER B09, MxL661 (IC U104)
Block diagram
Pinning information
19760_301.eps
back to 2015-Aug-08
div.table
8.5 Diagram 10-4-16 DEMOD_Toshiba TC90537 B16, TC90537FG (IC U101)
Block diagram
ADC Quadrature Interpolation ISIC (unguarded Adaptive

IF input Filter Frequency Pilot
detection phase pre/post echo
FFT interpolation
or IQ input ADC AGC Correction suppression) CPE extraction
AFC filter
Tuner Synchroni FFT window CVI CSI Equalization

AGC control output SW AGC Control (CW interference (With Doppler
zation (Reliability
control control detection) detection) )
Compensation
External AGC input
Tuner IIC IIC Layer TMCC

Host IIC control isolation demodulation
Frequency Demapping Viterbi Energy RS Error Synchroni-za

Crystal
Modulation division
Clock PLL CSI
Byte deinterleaving
despreading decoding detection tion flag
Bit deinterleaving
(reference clock) deinterleaving processing decoding
TS multiplex
Demapping Energy
Time CSI despreading Output
Memory processing control TS output
deinterleaving
Demapping Energy
CSI despreading
processing
TC90537FG
Pinning information
RLOCK
SLOCK
SLPEN
PBVAL
GPIO2
GPIO1
GPIO0
RERR
VDDC
SRCK
SRDT
VSS
12 11 10 9 8 7 6 5 4 3 2 1
VSS 13 48 VDDS
VDDS 14 47 VSS
RSEORF 15 46 SDA
SBYTE 16 45 SCL
SLADRS0 17 44 STSFLG0
AGCCNTI 18 43 STSFLG1
TC90537FG
AGCCNTR 19 42 SYRSTN
TNSCL 20 41 VPGM
TNSDA 21 40 AINN Q
XCKO 22 39 AINP Q
XO 23 38 AINN I
XI 24 37 AINP I
25 26 27 28 29 30 31 32 33 34 35 36
SLADRS1
ADCVDD
ADCVSS
PLLVDD
PLLVSS
VREFH
VREFL
TSMD
VDDC
VDDC
VSS
CKI
19480_304_130409.eps
130409
2015-Aug-08 back to
div.table
Block Diagrams TPM15.5L LA 9. EN 37
9. Block Diagrams
9.1 Block diagram 4900 & 5000 series
Silicon Tuner MxL661-AG-R

IF+/-
ATV LVDS
TSB Demod DTV
TC90537 DEMOD
VGA
MT5561 SPIDF Out
PC Audio in Headphone AMP

L/R
APA2176A
Headphone
CVBS / L / R
5W SPK
HDMI1 AUDIO AMP R

CN501 L/R
(Side) TI 31100
HDMI2 w/ARC L
CN502 5W SPK
Rear
CN103 USB1
(Side) (Share to Wi-Fi modul)
CN104 USB2
(Rear)
KeyPad UART
Remote Control
19760_400.eps
2015-Aug-08 back to
div.table
Circuit Diagrams and PWB Layouts TPM15.5L LA 10. EN 38
10. Circuit Diagrams and PWB Layouts

10.1 A 715G6863 PSU
10-1-1 Power
POWER
A01 A01
2
!
+
4 - 1 ǂ
BD9901
GBL408-C B+
Hot Cold L8602
47UH
R8612
NC/22K 1%
C8605
NC/100PF 500V
FB9903
3
FB9905 L8601 D8601 BEAD VLED+

FB9906 BEAD NC/47UH SR506
+16V_AL 1 2
1 2 1 2
6
! T9101
C9906 127R R9107 R9108 C8601 +

C9907 NC/100PF 250V 82K OHM 1% 82K OHM 1% 10 220UF 35V C8604 C8613 C8602 + + D8605 C8614
5
6
7
8
NC/100PF 250V A 100N 50V NC/100N 50V NC/100UF 50V 100N 50V
OUT
C9801 + + C9802 5 C8615 1N4148W
D
D
D
D
47UF 450V 47UF 450V C9102 R9129 Q8601 220uF 50V
2.2NF 8 30 OHM 1/4W AO4486
R9109 R9110 7 R9116
G
S
S
S
82K OHM 1% 82K OHM 1% 4 30 OHM 1/4W
2
2 FB
4
3
2
1
R9130 DIM
R8601
11 30 OHM 1/4W ZD8101
47OHM 1/8W
D9108 ON/OFF BZT52-B16G
D9105 1 R9119 C9114 NC/SR204 R8602 R8607
1
30 OHM 1/4W 1NF 500V 1 2 R8613 D8602 33K +-1% 1/4W
FR107 POWER X'FMR +12V_Audio 10ohm +/-1% 1/8W
3 L9902 2 100KOHM +-5% 1/8W
2
D9101 +12V1
8
7
6
5
SR510-22 +12V_AL 1N4148W R8603
R9105
1 2 C9107 10K OHM +-5% 1/8W ZD8102
FB
GM
CS/OVP DIM
GND
4R7 1/4W 5%
4 1 1NF 500V C8606 C8607 BZT52-B22
23mH D9102 10N 50V 10NF 50V
L9101
1
D9103 SR510-22 R8605
R9111
2 L9901 3 1N4148W 1 2 +12V IC8601 33K +-1% 1/4W
VCC
OUT
LED
10ohm +/-1% 1/8W
PF7708AS
D9106 D9110 3UH R8608 R8610
! 1N4007 SR510-22 5.6K 1/4W 0.2oHM 1% 1/4W
1
2
3
4
R9104 R9134 R9106 R9112 R8604
1 4 Q9101 C9100 1 2 C9117 + + C9108
330K +-1% 1/4W 330K +-1% 1/4W 330K +-1% 1/4W C8609 0.2oHM 1% 1/4W
NC 33R 1% 1/8W TK5A65D NC/100PF 470UF 25V 100N 50V R9122 CN8601
C9118 + C9111 12K 5% 1/4W LED_a NC/1NF 630V LED_a NC/CONN
R9121 470UF 25V 220uF 25V Vcc2
IC9101 0 OHM +-5% 1/8W
10K OHM +-5% 1/8W R9117 33ohm 1/4W +/-5% R9140 33ohm 1/4W +/-5%
C9903 C9904 1 6 R9113 D9104 +

R9102 GND OUT
5
100PF 250V 100PF 250V 2 5 1N4148W +16V1 C8608 C8603
3M3 1% FB VCC R9141 33ohm 1/4W +/-5%
2
R9118 33ohm 1/4W +/-5%

3 4 10UF 50V 470NF 50V LED2 CN8602
BNO CS OUT 6 3
R9142 33ohm 1/4W +/-5% 5 2 NC/CONN
R9135 PF6003AG ZD9103 + C9103 R9139 33ohm 1/4W +/-5%
VLED+ LED1 4 1
! ! 3M3 1% R9114
3.3M 1%
BZT52-B20 C9104
100N 50V
4.7UF 50V + C9106
4.7UF 50V
D9107
SR515 C9113 VLED+
3
2
1
4
1NF 500V +16V_AL LED4 1
C9109
R9103 1NF 50V D9109 LED3
R9115
7
100K 1/8W 1% SR515
1.2R 1%
470OHM +-5% 1/8W FB
1.2R 1%
R8609
R8606
1.2R 1%
R8611
! C9902 NC/470NF 305V
1R 1%
R8614
C9115 +
R9101 330UF 35V
C9901 0.36R
C9105
0.47uF 305V 220P 50V CN8603
2
R9903 R9905 R9901 1 NC/CONN
NC/750K +-5% 1/4W NC/750K +-5% 1/4W NC/750K +-5% 1/4W
D8604
R9904 R9902 R9906 1N4148W ǂ
NC/750K +-5% 1/4W NC/750K +-5% 1/4W NC/750K +-5% 1/4W +12V1
8
+16V_AL +12V Vcc2
R9907 +12V1 +16V1 Q8602 CN8604
6
1.5M 1/2W DTA144WN3/S CONN
5
R9127 4
2
R9125 NC/100K 1/8W 1% 3
680R 1/8W 1% C8611 C8610
JR901
2
680V ZD9102 100N 50V 100N 50V 1
RV9901 0R05 1/4W GDZJ22B
R9120 R9124
390K 1/8W 1%
1
4
22K 1/8W 1%
7
IC9102 R9128 R9136
C9119 1K5 +-1% 1/8W
2N2 50V EL817M(X) 470R 5%
C9112
R9138 Q8603
3
220N 50V 470 OHM 1/4W 2N7002K

HS9101 ON/OFF R8615
1
1K OHM +-5% 1/8W

1
5
R8616 C8612
FB9907 1 R9123 330K 1/8W 5% 100N 50V 3 CN8605
2
BEAD NR9902 NR9901 2 10K OHM +-5% 1/8W Q9102 2

5R 5R IC9103 2N3904 NC/CONN
3 1
t t 4 ZD9101 AS431AN-E1
2
BZT52-B15
!
2
4
1
HEAT SINK R9126

5K1 1/8W 1%
1
C9121
R9137
DIM
1K OHM +-5% 1/8W CN9101
FB9908 FB9901 100N 50V
BEAD BEAD ON/OFF
A R9131 PS_ON
2 1
1 2 0 OHM +-5% 1/8W
2
R9132 Scan_BL_EN 4 3
C9905 C9120 NC/0 OHM +-5% 1/8W 6 5
! 1NF 250V
!
100P 50V 8
10
7
9
12 11
+12V_Audio 14 13
F9901 16 15
FUSE 2.5A +12V
! GND3
+12V_AL
CN9901 CONN
1 JR902
2 1 0R05 1/4W
SOCKET
Hot Cold GND
3 2014-06-21
POWER 715G9863
19760_500.eps
2015-Aug-08 back to
div.table
10-1-2 Power layout top
MH2 MH3
CN8602
MH4 MH5
CN8601 L8602 CN9101
GND3
FB9903
D8601 L8601 J912
S13
D9108
C8601
CN8605
J910
J908
C9111
C8615 J909 C8608
J913
J914
CN8603 C8602 J907
CN8604
J906
J911
J905
J904
SU1
C9115
ZD9102
R9136
S12
L9101
D9106 IC9102
D9109
D9107
C9117 C9118
J903
HS9101
C9106
Q9102
C9103
Q9101 T9101 D9110

S6
C9100
D9105
R9101
D9102
SU3
D9101
C9102 C9905
J901
S7 FB9901
S10
S3
NR9902 C9906
S15
S11
FB9905
SU2
NR9901
F9901
FB9908
BD9901
C9802 C9902
C9901
L9901
C9801 L9902
R9907
CN9901
J902
S4
FB9906
RV9901
FB9907
C9907
C9904
C9903
S5 S8 S9
MH1
2014-06-05
LAYOUT TOP
715G6863
19760_501.eps
2015-Aug-08 back to
div.table
10-1-3
Q8602 Q8603
C9108
D8604 R8615
C8603 C8612
R8616
SM6
C9121
R9137
Power layout bottom
R9138
C9113
C9107 C9114 C8611
SM7
R9902 R9139 R9142 R9122
R9904 R9901 R9117 R9140
R9119
R9130
R9129
R9116
JR902
R9905 R9118 R9141
R9903 R9906
C8613
C8604
R9120 R9124
R9123 R9126
C9112
R9131
R8605 R8607
IC9103
R9127 R8608
R9132 C8610
R9125 R9128
Circuit Diagrams and PWB Layouts
C8606 C9120 C8609

ZD9101
R8603
R8601
R8613
S1 S2
R8602
C8607
Q8601
IC8601
R9108
R8609 D8602
R9107
R8611 R8610
TPM15.5L LA
R8612
R9109
R9110
R8606 R8604
R8614 ZD8102
C8605
D8605
10.
ZD8101
R9105
C8614
D9104
EN 40
C9104
R9115
JR901
C9105
R9113
R9103
R9121
R9135
R9104
C9109
2015-Aug-08 back to
div.table
R9112
C9119
IC9101
R9111
R9134 R9106 D9103

ZD9103
R9114 R9102
SM5
LAYOUT BOTTOM
715G6863
2014-06-05
19760_502.eps
10.2 A 715G6934 PSU

10-2-1 POWER
Power
A01 A01
3
R9161
33ohm 1/4W +/-5%
FB9902
! 127R HOT COLD C9161 C9162 R9162
4 1 1 2 1 2 1N5 50V 1N5 50V 33ohm 1/4W +/-5%
- +
FB9901 R9163
BEAD 33ohm 1/4W +/-5% +12V1 +12V'
BD9901
KBJ608G-FUC R9164
+ +
2
3
D9151 33ohm 1/4W +/-5%
C9801 C9802 C9104 R9105 C9105 FMEN-220A L9101
82UF 450V NC/68UF 450V 2.2NF 75K 2.2NF 2 3UH
+12V
AC-1 + + + + + Q9181
1
NC/AOD4185
C9156
NC/100N 50V
C9159
NC/100KOHM
C9155
R9181
NC/4.7UF 50V
C9160
L9902 C9151 C9152 C9153 C9154 C9158
470UF 25V 470UF 25V 470UF 25V 470UF 25V 1uF 220N 50V 100N 50V
! 4
18MH
1
SG9901
NC/DSPL-501N-A21F
3 2 AC-1
D9101
FR107G-A0 ! T9101 R9121
150 OHM 1/4W
R9182
NC/100KOHM
C9913 C9914 6 POWER X'FMR
220PF 250V 220PF 250V R9111 R9102
! ! 2M2 5% 1/2W 47K 1/4W C9123 C9124 R9122
150 OHM 1/4W
Q9182
NC/2N7002K
R9187
NC/10K OHM +-5%
1NF 500V 1NF 500V
5 7 PS_ON
NC/100N 50V
R9123
C9182
R9112 150 OHM 1/4W
3.3M 1/4W +22V
C9902
! 470nF 275V 4 11 R9124 R9183
3
2 8 D9121 150 OHM 1/4W NC/100KOHM
D9102 R9104 FMXA-2202S
R9908 2
! NC/390K
R9113
SS1060FL 22OHM 1/8W
3.3M 1/4W 1 10
C9907 + +
1
NC/47pF
R9106 C9121 C9122
U9901 47OHM 1/8W 220uF 50V 220uF 50V
10 OHM 1/4W
NC/CAP004DG-TL
10 OHM 1/4W
R9108
R9103
TK8A65D
Q9101
1 8 FB_1
NC NC 7 R9114
2 3.3M 1/4W C9103
3 D1 D2 6 R9107 NC
4 D1 D2 5 U9101 10K 1/4W
NC NC PF6003AHS
1 8
R9907 2 BNO VCC 7
! NC/390K 3 FB
CS
NC
VCC
6 +12V1
4 5 D9104
R9901 GND OUT
! SS1060FL D9103
2
510K 1/4W + FR107G-A0 L9301
ZD9301
+ NC/BZT52-B5V1 NC/47uH
C9110
2
R9902 C9111 C9112 2 1
NC/BZT52-B30
ZD9101
!
100K 1/8W 1%
R9110
510K 1/4W 1NF 50V 100N 50V 4.7UF 50V C9107 ZD9121 +5V
22UF 50V R9125 R9126 BZT52-B27
NC/10.5K OHM 1%
R9304
1
1
C9109 1K OHM 1K OHM +
2N2 50V FB9301 U9301
R9903 NC/AOZ3015AI C9309
NC/470UF 25V
!
C9306
NC/220N 50V
C9307
NC/BEAD
510K 1/4W 1 8 NC/2N2 50V
470 OHM 1/4W

R9127
1
R9109 2 PGND EN 7 R9301
470 OHM 1/4W VIN LX
NC/30 OHM 1/4W

NC/20K 1/4W
R9302
R9904 3 6
! 510K 1/4W HS-GND 4 AGND COMP
VCC FB
5 R9303
C9108 R9101 Q9121 NC/30 OHM 1/4W
R9905
220P 50V 0.22OHM +-5% ! BTN5551A3
C9308
! 510K 1/4W C9921
+
NC/2N2 50V
R9305
NC/220R 1%
NC/470UF 25V
C9302
NC/220N 50V
C9303
NC/100N 50V
C9304
NC/100N 50V
C9305
470PF 250V
R9906
! 510K 1/4W
100N 50V
R9128
C9125
1K 1/8W
R9306
NC/2K 1/8W 1%
L9901
! 3 18MH 2
FB9904 !
HS9901 HS9101 BEAD
NC/HEAT SINK HEAT SINK C9920
SG9902 1 2 470PF 250V
4 1 NC/DSPL-501N-A21F HS-GND
2
1
4
3
2
1
! C9901
470nF 275V
FB_1 +12V1 +12V' +22V
1
CN9902 CN9101
NR9902 NC CONN DIM
t
2 2.5R
1 1 2 1 PS_ON
2 L ON/OFF 4 3
FB9903
N BEAD 6 5 C9157
8 7 100N 50V
2
10 9
R9175 R9129 +12V_AUDIO
12 11
680R 1/8W 1%
0 OHM +-5% 1/8W

R9173
1K5 +-1% 1/8W
330K 1%
R9172
2
1 2 14 13
D9105 16 15
FB9905 NC/1N4148W PS_ON C9301
NC/220N 50V
! BEAD
! 4
! 1
D9152
+5V SR34
1
C9911 C9912 U9102
100PF 250V 100PF 250V EL817M(X) R9176
Q9102 10K 1% +12V
6.8KOHM +-1%
R9184
3 2
NC/LMBT3906LT1G C9172
10K OHM +-5% 1/8W

R9185
220N 50V
! C9106
NC/4N7 50V
Q9183
2
RV9901 GND1 GND2 GND3 GND4 GND5

680V 2N7002K HS9151 HS9152 HS9121 HS9122
C9171 R9171 GND GND GND NC NC HEAT SINK NC/HEAT SINK NC/HEAT SINK HEAT SINK
1
! ! 22NF 50V 2K OHM

2
4
1 3 1 1 1
5A 250V
BZT52-B15
F9902
ZD9171
2 4 2 2 2
NC/5A 250V
F9901
1
3 3 3
1
100KOHM +-5% 1/8W

R9186
t 4 4 4
! U9103
1
3
NR9901
2
2.5R AS431AN-E1
R9174
2 1 3K9 1/8W 1%
CN9901
SOCKET
4 2014-03-05
POWER
715G6934
19760_503.eps
2015-Aug-08 back to
div.table
10-2-2 LED DRIVER
LED DRIVER
A02 A02
L8602 FB8602
+22V NC NC/BEAD
D8602
NC/SR506 1 2
6 VLED+
FB8601
4 L8601 BEAD
33uH D8601
SR506 1 2
8
D8605 +
NC/1N4148 + +
C8601 OUT C8605 R8603 R8604 C8606 C8607
220uF 50V 100N 50V C8603 C8604 100K NC 1uF 1uF
220uF 50V 220uF 50V
2
R8612
33K 1/8W 1% R8605
10ohm +/-1% 1/8W Q8601 R8619
CYS9240 10 OHM
ZD8601
NC/BZT52-B22 D8603 D8604
2 1
VCC SS1060FL R8607 SS1060FL

5.1R 1/8W
R8606
33K 1/8W 1%
C8613 Q8602
100pF 50V LMBT3906LT1G
ZD8602
R8608 +12V VCC
NC/BZT52-B22
10K 1/8W
1
R8602
10R 1/8W 5%
R8609
OUT VLED- NC/0R05 1/4W C8615 R8620 C8616

ON/OFF 100N 50V 2K2 1/8W 2.2UF 25V
U8601
PF7708AS
1 8 R8610
2 LED FB 7 4K3 1/8W 1%
3 VCC GM 6
4 CS/OVP DIM 5 DIM
OUT GND R8621
1K 1/8W 1%
R8601
R8611 0.05R R8622
+ 33K 1/8W 1% 10K 1/8W 1%
ON/OFF Q8603
1NF 50V
C8610
C8611
C8609
C8608 LMBT3904LT1G
220P 50V
NC/22UF 50V
C8614
220N 50V 22pF 50V
C8612
47N 50V R8623 C8617
300K 1/8W 5% 100N 50V
CN8601
CONN
12
VLED+ 11
10
VLED- 9
VLED- 8
R8618 7
R8613 R8614 R8615 R8616 R8617
1R2 1% 1R2 1% 1R2 1% 1R2 1% 1R2 1% 1R2 1% 6
5
4
VLED- 3
VLED- 2
1
VLED+
4 2014-06-05
LED DRIVER 715G6934
19760_504.eps
2015-Aug-08 back to
div.table
2014-06-06
LAYOUT TOP
715G6934
19760_505.eps
2015-Aug-08 back to
div.table
10-2-4 Power layout bottom
2014-06-06
LAYOUT BOTTOM
715G6934
19760_506.eps
2015-Aug-08 back to
div.table
10.3 A 715G6338 PSU

10-3-1 AC input
A01 AC input A01
! F9901 SG9901
NC
1 2
3 4
FUSE
T5AH/250V ! ! ! !
! C9905
R9902 3.9MOHM +-5% 1/2W

L9901
3
C9903 470pF 250V
RV9901 680V
12mH L9902
! 100PF 250V
! ! ! 12mH !
1
1
BD9901
1
TS10K80-02
CN9901 4 1
100NF 305V
C9902
-
100NF 305V
SOCKET +
C9901
4
! !
2
2
C9906
C9904 470pF 250V Vsin
100PF 250V NR9901
NR9902
2.5R
t
2 1 1 2
t SG9902
2.5R NC
A
B
HOT COLD
R9901
C9907
! ! NC
HS9901
470pF 250V
HEAT SINK
1
2
3
4
1
D1
D1
NC
NC
2
IC9901 3
C9908
NC
NC
4
D2
D2
NC
NC
8
7
6
5
R9903
NC
!
HS9902
1
2
B
HEAT SINK
2013-10-18
AC input 715G6338
19600_507.eps
2015-Aug-08 back to
div.table
10-3-2 LED Driver
LED Driver
A02 A02
L8101 CN8101
VLED+ CONN
33uH
3
D8101 1
+36V/+24V MBRF10100CT 2
2 2 FB8101 1 VLED_1 3
VLED+
2
Q8102 4
PMBT3906
220nF50V
5
ON/OFF
C8104
127R 6
1
R8133 + 7
R8111 VLED_2
C8102
C8132 10K OHM +-5% 1/8W C8108 + + 8
C8103
100N 50V C8101 150K 1/4W +/-1% 9
100N 50V Q8101
82uF 100V
330UF 50V 10
82uF 100V
220nF50V
C8105
D8102 P3710BTF 11
R8134 SS1060FL 12
2.2 OHM 1/8W

10K 1/4W R8112
10K 1% 1/8W
R8101
R8102 150K 1/4W +/-1% VLED+
R8103
33 OHM
ZD8101 R8135
R8136 10ohm +/-1% 1/8W
+36V/+24V BZT52-B9V1_R1_00001 Q8103 OVP_L
2 1 2N7002K +12V R8116
10KOHM +-1% 1/8W

0R1 5% 2W
10N 50V
20K OHM C8106
C8114
100N 50V
R8113
R8137 R8138 C8133 R8104
100K 1/8W 1% VLED_1
20K OHM 1N 50V 0R1 5% 2W
R8105
1N 50V
C8107
R8139
IC8101 1K 1/8W 1%
10ohm 1% 1 24
OVP_L VIN DRV
2 23 R8106
3 OVP GND 22
EN CS 10K 1/8W 1%
4 21
5 RT DIM 20 R8155 DIM R8148 Q8143
COMP LOSC 0R051/8W
100K 1/8W 1% 6 19 200K 1/8W MTBA5N10J3
330K 1% 1/8W
PARL STATUS
R8140
R8108
C8131 7 18 C8143
SENSE1 FB4
510 OHM +-1% 1/8W

1N 50V G1 8 17 G2 100P 50V G1 Q8149
Gate1 Gate4
240K 1% 1/8W
SENSE2 9 16 R8164 MTBA5N10J3
FB1 SENSE4
240K 1% 1/8W
R8149
R8123
R8107
10 15
20K
200K OHM
240K 1% 1/8W 100KOHM +-1% 1/8W

11 SENSE2 FB3 14
Gate2 Gate3 S1
R8120
G2 12 13 SENSE2
FB2 SENSE3
R8110
100N 50V
C8110
LD7890GS
100K 1/4W
0R68 1W 5%
S1
R8124
100KOHM +-1% 1/8W
0R68 1W 5%
4.7R 1%
4.7R 1%
1UF 50V
C8109
R8109
R8156
R8144
R8146
R8147
R8157
R8145
R8161
0R68 1W 5%
0R68 1W 5%
0R68 1W 5%
0R68 1W 5%
R8121
R8160
R8115 VLED_1
1M 1/8W 5% Q8147
P5002CMG
Q8145
P5002CMG
R8143
100KOHM +-5% 1/8W

10K 1/8W 1%
2D/3D
C8144
100N 50V
R8142
FB8103
BEAD
1 2
FB8102
BEAD
1 2
GND801 GND802 GND803
1 1 1
HS8101
1 GND GND GND

2
3
4
GND804 GND805 GND806
HEAT SINK 1 1 1
GND GND GND
GND807
GND
2013-10-18
LED Driver
715G6338
19610_501.eps
2015-Aug-08 back to
div.table
10-3-3 LLC 36V
LLC 36V
A03 A03
R9101 R9102 R9103

1MOHM +-1% 1/4W 1MOHM +-5% 1/2W
1MOHM +-5% 1/2W
HOT COLD HS9109
HEAT SINK
C9102 R9104 1
100N 50V 22K 1/8W 1% 2
3
4
FB9101
BEAD R9105
0.1R T9101
1 2 12
B+
R9106
4R7 +-5% 1/8W
D9105
UF1010G
!
C9101 10
10NF 10
IC9101 C9103
1
LCS700LG-TL 470NF 50V 1 8 L9102 +36V/+24V
16 2 9 1.1uH
D 2
14 5
VCCH 13 6 D9104
HB 11 FMEN-2308 R9132 R9133
3
11 7 + C9121 + C9122 R9121 R9122 + C9125
12K 5% 1/4W
12K 5% 1/4W
C9123
NC
S2 10 330UF 50V NC
12K 5% 1/4W
12K 5% 1/4W
100N 50V
S1 9
NC 8
IS 7 9
DT/BF 6
FB 210uH
5
OV/UV 4
G 3
VREF R9108 C9106
1 1K 1/8W 1% 47pF 1
VCC 2
+36V/+24V 3
4
R9107 C9105 5
2.2R C9107 R9109 22nF 6
VCC_ON 470pF 50V 120R 1% 7
8
9
10
+36V/+24V 11
+12V 12
ON/OFF
+ 2D/3D 13
C9120 14
DIM
10UF 50V
2
CN9101 CONN
R9128 ZD9103
BZT52-B43
8.2K 1/4W
R9110
2.4KOHM +-1% 1/8W

C9104
1
1uF
R9124 +36V/+24V R9138
2.4KOHM +-1% 1/8W 1K 1/8W 1%
R9136
R9125 D9110 1K 1/8W 1%
1K 1/8W 1%
D9106 SS1060FL
C9110
150KOHM +-1% 1/8W
R9111
SS1060FL Q9103 D9108

2.2UF 25V R9129 PMBS3906R9137
! SS1060FL
1uF
C9108
0 OHM +-5% 1/8W

C9109 2.4KOHM +-1% 1/8W
OVP
4N7 50V R9112 R9113 C9126
12K 1/8W 91KOHM +-1% 1/8W IC9102 2.2nF 50V R9123
HS9101 PS2561DL1-1 100KOHM +-1% 1/8W R9139
1
100 OHM 1%
1 C9113 R9126 C9116
2 1uF 4K7 1/8W 1% 47nF 50V
D9107 R9120
Q9104
2
R9114 SS1060FL C9117 2K4 +/-1% 1/8W
2.2nF 50V PMBS3904
HEAT SINK 22KOHM +-1% 1/8W 3K 1/8W +/-1% R9127
R9115 43R 1% R9140 C9133
1K 1/8W 1% 100N 50V
IC9103
C9111
33N 50V AS431AN-E1 R9119
11K 1%
C9128 C9127
1uF 1uF
A 2013-10-18
LLC 36V
715G6338
19610_502.eps
2015-Aug-08 back to
div.table
10-3-4 Main Power 12V
Main Power 12V

A04 A04
R9306
0.1R
B+
HOT COLD
C9301 R9307 R9309
!
10NF 100K 1/4W 100K 1/4W R9326 R9327
5 T9301 51 OHM 1/4W 51 OHM 1/4W
1
R9301 ZD9303 6
6.8K 1/4W C9302 R9322 R9323
NC/P6KE160AA0 51 OHM 1/4W
1NF 4 51 OHM 1/4W
R9308
2
R9318 R9319
10
100K 1/4W R9310 7 51 OHM 1/4W 51 OHM 1/4W
100K 1/4W 3
R9320 R9321
R9302 2
6.8K 1/4W 51 OHM 1/4W 51 OHM 1/4W
9
1 C9309 +12"V +12V +12V_audio

2N2 500V
R9303 POWER X'FMR/380GL32P133H00 D9305
1
6.8K 1/4W D9302 FME-220B C9310 L9301
ZD9302 FR107 2N2 500V 3UH
BZT52-B30 D9301 2
SS1060FL
2 1 2 1
Q9301
3
ZD9301 TK13A65U C9306 + C9314 C9315 C9319
BZT52-B30
470UF 25V
C9311
470UF 25V
C9312
470UF 25V
C9313
470UF 25V
C9317
470UF 25V
C9318
NC/ 470UF 25V

C9321
NC + + + + + + 330UF25V
R9324 R9325 100N 50V 100N 50V
R9312 R93 16 NC NC
51 OHM 1/4W R9313 2.2 OHM 1/4W
10KOHM D9306
1
R9311 FME-220B
10 OHM
2
IC9301
1 8
2 CT HV
3
3 COMP 6
C9304 4 CS VCC 5 R9314
NC/100KOHM +-5% 1/8W
R9305
1N 50V GND OUT 0.27R

C9303 LD7752B
47nF 50V
VCC
R9315 D9304 D9303

470 OHM 1/4W FR107 FR107
C9305 CN9301
470P 50V CONN
+ + 1 2 ON/OFF
C9308 C9307 DIM 3 4
C9320 2D/3D
100N 50V 10UF 50V 47UF 50V PS_ON 5 6
7 8
9 10
11 12
HOT COLD OVP
+12V
13 14
+12"V
DV5
+12V_audio
+12V
R9337 Q9332
2Kohm 1/4W +/-5% PMBT3906
VCC +12V
R9346
2Kohm 1/4W +/-5% R9336
! 2Kohm 1/4W +/-5% R9333
10K 1/8W 1%
!
PS2561DL1-1
R9347 R9343
4
2.2KOHM +-1% 1/8W 9.53KOHM +-1% 1/8W

D9331
PS2561DL1-1
IC9331
4
1
SS1060FL R9334
R9345
IC9341
10K OHM
3
6.2K OHM +-1% 1/8W Q9333

BTC4672M3
2
R9348 C9341 Q9341 R9341
1K 1/8W 1% 220N 50V 2N7002K 10K OHM +-5% 1/8W R9335
IC9342 10K OHM +-5% 1/8W
DV5
2
2
AS431AN-E1 VCC_ON
BZT52-B15
ZD9340 Q9331
R9331
ZD9330
BZT52-B16 2N7002K
R9342 10K OHM +-5% 1/8W
100K 1/8W 1%
R9344 PS_ON
3.9K 1% 1/8W 100K 1/8W 1%
1
R9338
C9332 +
1
10UF 50V
C9331 R9332
100N 50V
330K 1% 1/8W
HOT COLD
HOT COLD HS9301
HEAT SINK
HS9302
HEAT SINK
!
1 1 C9328
2 2 470pF 250V
! FB9301 3 3
C9316 BEAD 4 4
1NF 250V
1 2
A 2013-10-18
Main Power 12V

715G6338
19610_503.eps
2015-Aug-08 back to
div.table
10-3-5 PFC
PFC
A05 A05
L9803 D9801 D9805
NC IN5408G-04 IN5408G-04
1 2
L9802 FB9802
BEAD D9802 BEAD
MUR460-28
Vsin
1 2 ! 1 2
B+
2
L9801 FB9803 D9806 NC/FMNS-1106S
240UH BEAD + + +
68uF 450V
C9810
68uF 450V
68uF 450V
C9811
C9812
C9813 C9801 C9815
1UF 450V 1UF 450V 2.2NF
1
R9807 D9803
Q9801
10 OHM 1/8W SS1060FL C9808
TK16A60W 100PF
R9805 R9801
20K 1/4W
10K 1/8W
R9809
1MOHM +-1% 1/4W
R9808
75 OHM 1/8W
R9802
1MOHM +-1% 1/4W
R9806 R9811
VCC_ON C9802 3.3KOHM +-1% 1/8W 0.1R
47P 50V
R9803
R9 81 5
2.2R 1MOHM +-1% 1/4W
8
7
6
5
IC9801
COMP OUT
VCC
RAMP GND
ZCD
C9803 LD7591T R9814 R9804
100N 50V C9809 19K1 +-1% 1/8W
NC
100P 50V
INV
CS
R9810
470 OHM 1/4W
1
2
3
4
C9807
1N 50V
R9813
R9812
10K 1/8W
27K 1/8W 1%
C9805
C9806
HOT COLD 100N 50V
470NF 50V
HS9801
HEAT SINK
1
! C9814
2
3
470pF 250V 4
A 2013-10-18
PFC
715G6338
19610_504.eps
2015-Aug-08 back to
div.table
MH7 CN8101 MH6

CN9101 CN9301
GND804
J9112
GND805
J9114
J9126
J9147
J9101
J9110
J9138
C8102
HS8101
J9132
J9148
C9314 FB8102
J9142
FB8103
J9127
J9113
J9146
J9117
D8101 Q8101
R8145
R8157
R8144
R8146
R8147
R8156
MH8 J9129 J9141
MH5
C8103 C9123
GND803
J9139
GND806
J9108
J9109
J9118
FB8101 L9301 J9140
C9318
GND1
C9311
J9125
R8104
R8116
C8101
MH9 L9102 MH4
C9317
HS9109
D9104
C9121
C9122
D9305
C9312
J9120
HS9302 J9143
J9121
L8101 J9145
C9313
D9306
J9102
SU1 C9321
J9131
FB9301
GND802
GND807
T9101
J9137
IC9102
MH10 MH3
C9316
IC9331
IC9341
H10
T9301
MH11
C9328
H2
D9303
C9302
J9134
C9106
C9105
C9320
R9102
D9304
C9120
D9105
C9307
J9105
R9103 J9136
D9302
R9105 SU3
J9144
J9135
ZD9303
J9133
J9104
IC9101 C9301
HS9101 R9314
C9306
J9103
Q9301 HS9801
J9111
R9306
SU2
J9122
J9107
C9101
FB9101 HS9301
C9908
C9332
J9119
D9806 Q9801
RV9901 L9803
J9123
R9901
L9802 FB9802
R9903
C9801
SU4 FB9803
D9805
C9808
NR9901 SG9902
C9815 D9802
J9128
C9813 J9130
R9811
HS1
HS2
HS3
L9901 L9902
J9115
D9801
J9124
NR9902
SG9901 C9902
BD9901 HS9901
C9906
L9801
HS9902
C9901 H8
R9902 C9905 C9811 C9810 C9812

H7
F9901
C9904
C9903
H5
SU5
H6
C9907
CN9901
MH12
C9814
H9
H11
GND801
A 2013-10-18
MH1 LAYOUT TOP
715G6338
19610_505.eps
2015-Aug-08 back to
div.table
10-3-7 Power layout bottom
JR8106
R8115
R8149
C8110
R8107
C8109
C8132
R8106
JR8101
Q8149
Q8143
C8114
R8113
SE7
R8164
C9319 R8148
R8133
R8124
R8123
Q8102
R8135
SE6 R9325
Q8103
R9324
R8111
R8112
R8134
C9315
JR8102 IC8101
R8108
C8106
R8139
C8133
R8138
C8104
C9125
R8101
R8102
ZD8101
D8102
R8137
R8155 C8143
C8107
R8105
R8160
R8161
R8110 R8120 R8103
R8142
C8144
Q8145
Q8147
R8140 C8105 R8143
R8136
C8131
R8109
R8121
C9309
R9321 R9322
C9310 R9319 R9318
C8108
R9320 R9121
R9323
R9122
R9327 R9326
R9132
ZD9103
D9110
R9133
R9140
C9133
R9139
R9331
Q9104
Q9331
C9331
R9123
R9128
D9108
Q9103
R9332 R9119
R9124
R9125
Q9341
R9334
IC9103
C9128
C9127
JR8100
R9120
R9341
R9342
R9333
ZD9340
Q9332
R9137
R9138 C9117
R9345
IC9342
R9136
R9129
C9126
R9335 C9116 R9127
R9336 R9126
R9344
R9348
R9347
R9343 R9346
C9341
R9337
R9302
R9301
R9307
R9309
R9316
R9308
ZD9330
D9331
R9303
R9338
R9310
Q9333 R9110
R9104
ZD9301
R9111
C9109
C9102
R9101
C9108
ZD9302
R9805
R9107
R9810 C9807
C9104
C9103 C9107
R9106
R9812 R9311
R9312
D9301
R9108 C9111
D9106
R9806
C9308
IC9801 IC9301
R9112
R9114
R9115
C9806 R9313
C9802 C9303
R9813
D9107
R9305
C9305
C9803 C9805
R9109
C9110
C9304
R9815 C9809 JR8105

R9807
R9315 R9113
R9814
C9113
D9803
R9804
R9808 IC9901
R9809 R9803 R9802
R9801
SE5
A 2013-10-18
LAYOUT BOTTOM
715G6338
19610_506.eps
2015-Aug-08 back to
div.table
10.4 B 715G6836 SSB

10-4-1 System Power
System Power
B01 B01
3V3SB
+5VSB +5V_SW 4,5,6,7,8,9,10,11,12,13,14,15,16,17,18 GND
90mil 12V_AMP
CN701 6 12V_AMP
FB703 120R R738 +12V
10 +12V
Pre_12V
Pre-12V_AMP
2
4
1
3
Pre_12V
Pre-12V_AMP 1
1 2
2
+12V 4.7K 1/16W 9,10,11,12,15
7,9,16
+5V_SW
+5VSB
+5V_SW
+5VSB
6
8
5
7
FB701 120R 12V_AMP Main power On/Off control R709
22K 1%
C706
1UF 10V 1
Q702
8
4,8,10,13,14
4,5,6,8,9,10,11,13,15,16,17,18
3V3SB
DVDD3V3
3V3SB
DVDD3V3
R705 LO = > POWER_ON S D
AC_DET# 10 9 STANDBY PS_ON HI = > POWER_OFF 2 7
S D 8,13,15 AVDD1V2 AVDD1V2
INVERTER_ON_OFF 12 11 BRIGHT_ADJ 3 6
1K 1/16W 1% 4 S D 5 17 VCCK VCCK
Q708 OPWRSB VCCK G D
R710
PS_ON /STANDBY BC847C 51K 1/16W 5% NC SM4310PSKC
CONN R739
H = > POWER_ON 4.7K 1/16W R713 +
L = > DC_OFF
2.2K 1%
Q703
LMBT3904LT1G +5VSB
C707
100UF 16V Control Interface
OPWRSB
4 OPWRSB BL_DIMMING
C708
14 BL_DIMMING BL_ON/OFF
NC/4.7UF 10% 10V
14 BL_ON/OFF AC_DET
Q701 +5V_SW
10 AC_DET AC_Off
AO3401A
10 AC_Off
C742
100pF 50V R746 0R05 1/16W
+5V_SW
R747 100K 1% FB706 DVDD3V3
U705
L701
U706 1 2 1 5
R748 C743 2 VIN LX
120R 2.2uH R1
13K 1/10W 1 6 3 GND 4 82K 1%
FB BS 0.1uF 50V EN VFB
R729 +
+5VSB C721 R728 G5695T11U C722 C731 C719
L703 2.2UF 0R05 1/16W 10UF 6.3V 20% 100NF 16V 100UF 16V
R749 2 5
EN LX R730 R2
36K 1% 18Kohm 1/16W +/-1%
4.7uH +12V C746 C747 +
20K OHM 1/16W 1%
22UF 10V 22UF 10V C748

3 4 R752 0R051/8W 100UF 16V
GND IN
R750
C744
R706
SY8104ADC
C745 100K 1%
10N 50V
1UF 10% 16V
R751 40.2K 1/16W 1%

INVERTER ON/OFF
AC_Off
DVDD3V3
+12V
AC_DET# AC_DET 3V3SB
ZD701 R704
R754 1 2 100R 1/16W 5%
BL_ON/OFF R722 INVERTER_ON_OFF
1K 1/16W 1%
Q704 R753 PDZ5.1B C705 R779 R778 NC 0R05 1/16W
LMBT3906LT1G 100NF 16V 1K 1/16W 5% 4.7K 1/16W
10K +-1% 1/16W INVERTER_ON_OFF
AC_DET R724 C725
H = > AC_ON NC 10K +-1% 1/16W NC/10UF 10V
INVERTER ON/OFF R780 BL_ON/OFF
L = > AC_OFF_DET H: ON
L: OFF Q707 4.7K 1/16W
MMBT3904 Low active
AVDD1V2
CORE POWER 1.2V R719
0R051/8W
+5VSB
U703
VCCK
BRIGHT ADJUST
M5723B-33F61U L702 DVDD3V3
8 10 1 2
IN1 LX 2.2uH FB702 3V3SB
120R BL_DIMMING R786 BL_DIMMING R723 BRIGHT_ADJ
C712 Max:3.3V 1K 1/16W 5% NC 100R 1/16W 5%
2.2UF R717 C714 C730 Min: 0V
10K +-1% 1/16W NC/100N 16V 10UF 6.3V 20%
R787 R725 C726
PS_ON 1 3 BRIGHT_ADJ 4.7K 1/16W NC 10K +-1% 1/16W NC/22uF 10V
EN1 FB1
R785
100R 1/10W 5% R788
6 Q705 BL_DIMMING
IN2 MMBT3904 4.7K 1/16W
3V3SB R718
C713 R714 10K +-1% 1/16W
1UF 10% 16V 10K +-1% 1/16W
5 7
EN2 OUT2
C710
PGND
AGND
AGND
tGND
4.7UF 10% 10V

2
4
9
11
3 2014-07-07
System Power
715G6836
19760_507.eps
2015-Aug-08 back to
div.table
10-4-2 Peripheral
Peripheral
B02 B02
U401B DVDD3V3
NAND Flash 3,5,6,7,8,9,10,11,12,13,14,15,16,17,18 GND
PDD0 G2 R5 OSCL0 U405
PDD0 OSCL0
R401
R402
R403
PDD1 G4 P5 OSDA0 TC58NVG0S3ETAI0
PDD2 K3 PDD1 OSDA0 F4 OSCL1 1 48
G3 PDD2 OSCL1 F5 2 NC NC 47 3,8,10,13,14 3V3SB 3V3SB
PDD3 OSDA1
PDD3 OSDA1 NC NC 46 3,5,6,8,9,10,11,13,15,16,17,18 DVDD3V3 DVDD3V3
4.7K 1/16W
PDD4 H3 3
PDD4 NC NC 45
4.7K 1/16W
4.7K 1/16W
PDD5 J6 V19 XTALI 4
PDD6 G1 PDD5 XTALI W20 XTALO 5 NC NC 44 PDD7
PDD7 J3 PDD6 XTALO FB409 120R 6 NC I/O7 43 PDD6
PARB# K4 PDD7 W10 1 2 ORESET# PARB# 7 NC I/O6 42 PDD5
POOE# J1 PARB#
POOE#
ORESETB
OPWRSB
T2 OPWRSB POOE# 8 R/B1
RE
I/O5 41
I/O4 40
PDD4 GPIO Interface
POCE1# J2 T3 OIRI POCE1# 9 OPWRSB
POCE0# J4 POCE1# OIRI 10 CE1 NC 39 DVDD3V3 SY S_EEPROM_WP OPWRSB 3
TP409 PACLE K1 POCE0# U2 U0RX 11 NC NC 38 OIRI SY S_EEPROM_WP 14
DVDD3V3
PAALE K2 PACLE U0RX U1 U0TX 12 NC NC 37 OIRI 10
POWE# J5 PAALE U0TX 13 VDD VDD 36
POWE# VSS VSS 35
R405
14
R404
C401
T17 AVDD33_REG_STB 15 NC NC 34 100NF 16V
AVDD33_REG_STB NC NC 33 I2C & UART Interface
4.7K 1/16W
PACLE 16
4.7K 1/16W
FSRC_WR A20 Y 10 AVDD10_LDO PAALE 17 CLE NC 32 PDD3 OSCL0
TP401 FSRC_WR AVDD10_LDO POWE# 18 ALE I/O3 31 PDD2 OSDA0 OSCL0 6
Flash_WP# 19 WE I/O2 30 PDD1 OSCL1 OSDA0 6
C402 20 WP I/O1 29 PDD0 OSDA1 OSCL1 11,18
R407 MT5561LVNT 21 NC I/O0 28 OSDA1 11,18
4.7UF 10% 10V
4.7K 1/16W C403 22 NC NC 27 U0TX
100NF 16V 23 NC NC 26 U0RX U0TX 16
24 NC NC 25 U0RX 16
3V3SB NC NC
AVDD33_REG_STB
LED_POWER_RED
LED_PWR_GREEN LED_POWER_RED 10,14
LED_PWR_GREEN 10,14
C404 C405
100NF 16V 100NF 16V
RESET Circuit
3V3SB
LED_POWER_RED R473 OPCTRL0

R477 0R05 1/16W
16K 1% LED_PWR_GREEN R474 OPCTRL1
UART Port 0 0R05 1/16W
3V3SB
R411 R412 10mil ORESET#

2
CN402 X401
4.7K 1/16W 4.7K 1/16W XTALI 1 3 XTALO
1
STRAPPING OPWRSB R414 10K +-1% 1/16W
U0TX R170 100R 1/16W 5% 24MHz R479 C462
4
2 22K 1% 100NF 16V

U0RX R171 100R 1/16W 5% 3 DVDD3V3 R415 10K +-1% 1/16W PACLE R416 NC/10K 1/16W 5%
C406 C407
TXC
1
15PF 50V 15PF 50V

CONN 3V3SB R417 NC/10K 1/16W 5% OPCTRL0 R418 10K +-1% 1/16W
ZD109 ZD110
R419 NC/10K 1/16W 5% OPCTRL1 R420 10K +-1% 1/16W
AZ5123-01H AZ5123-01H
2
SYSTEM EEPROM DVDD3V3

LO = >WRITE
HI = >WP
5/28 BGA Strapping OPCTRL1 PACLE OPWRSB OPCTRL0
R421 R422 R423
10K +-1% 1/16W U406
Heat Sink ICE mode + 24M + serial boot X 0 0 0
4.7K 1/16W 10K +-1% 1/16W
8 1
SY S_EEPROM_WP R425 7 VCC E0 2 HS401
ICE moce + 24M + ROM to Nand boot X 1 0 0
OSCL0 0R05 1/16W R172 100R 1/16W 5%6 WC E1 3
OSDA0 R173 100R 1/16W 5%5 SCL E2 4 2 ICE mode + 27M + serial boot X 0 0 1
SDA VSS 1
M24128-BRMN6TP
ICE moce + 27M + ROM to Nand boot X 1 0 1
HEAT SINK
4 2014-07-07
Peripheral
715G6836
19760_508.eps
2015-Aug-08 back to
div.table
10-4-3 Audio A-in/I2S/HP
B03 Audio A-in/I2S/HP B03

C687
22PF 50V FB405 120R
3,4,6,7,8,9,10,11,12,13,14,15,16,17,18 GND
SPDIF_OUT 1 2
U401C DVDD3V3
R20 3,4,6,8,9,10,11,13,15,16,17,18 DVDD3V3
R4 AIN_R0 U20
FB406 120R ARC_SPDIF F16 ASPDIFO AIN_L0 R17 YPBPR_R_IN
ASPDIFI AIN_R1 V20 YPBPR_L_IN
AOMCLK 1 2 R60122R 1/16W 5% MCLK R2
AOMCLK
AIN_L1
AIN_R2
R19 CVBS_R_IN I2C & UART Interface
AOBCK R602 22R 1/16W 5% BCK R1 T20 CVBS_L_IN OSDA0
AOLRCK R603 22R 1/16W 5% LRCK P3 AOBCK AIN_L2 R18 VGA_IN_R OSCL0 OSDA0 4,6
AOSDATA0 R604 22R 1/16W 5% SDATA0 R3 AOLRCK AIN_R3 T19 VGA_IN_L U0TX OSCL0 4,6
T4 AOSDATA0 AIN_L3 U0RX U0TX 4,16
C603 TP404 AOSDATA1 P16 AR0O U0RX 4,16
NC/33P 50V TP AR0_ADAC R16 AL0O
AL0_ADAC U19
C604
NC/33P 50V AR1_ADAC
AL1_ADAC
T18 DVDD3V3 Audio Input Interface
C605
NC/33P 50V M16 AVDD33_ADAC R678 CVBS_R_IN
C606 AVDD33_ADAC M14 AVDD33_AADC CVBS_L_IN CVBS_R_IN 8
AVDD33_AADC 0R05 1/16W CVBS_L_IN 8
NC/33P 50V L15 AVDD33_CAP C607 C684 C688
VMID_AADC T16 AVDD33_CAP YPBPR_R_IN
VMID_AADC 100NF 16V 10UF 6.3V 20% 22UF YPBPR_L_IN YPBPR_R_IN 8
YPBPR_L_IN 8
15mil VGA_IN_R
TP408 VGA_IN_R 7
MT5561LVNT VGA_IN_L
TP VGA_IN_L 7
C608
1UF 25V I2S Interface
AOMCLK
AOBCK AOMCLK 6
AOLRCK AOBCK 6
AOSDATA0 AOLRCK 6
AOSDATA0 6
SPDIF_OUT
ARC_SPDIF SPDIF_OUT 9
HP_DET# ARC_SPDIF 16
HP_DET# 10
PreAmp output for Headphone HPL_IN
HPL_IN 6
HPR_IN
HPR_IN 6
OUTR
R620 27K 1/16W 5% OUTR OUTL OUTR 6
CN605 OUTL 6
C646 OUTL 2 1 2
C647 47pF 50V FB611
R622 10K +-1% 1/16W 1 A
AR0O R623 HPR_IN NC 30R
10K +-1% 1/16W
2.2UF C648 OUTR 2 1 4
330pF 50V FB612
B
C602
C601
NC 30R 3
NC 22NF25V
NC 22NF25V
NC CONN
R615 27K 1/16W 5% OUTL
C643
C644 47pF 50V
AL0O R617 R618 10K +-1% 1/16W HPL_IN
10K +-1% 1/16W
2.2UF C645
330pF 50V
DVDD3V3
PreAmp output for Line out
HPOUT_RT
R637 HPOUT_LT
4.7K 1/16W
5 CN602
C650 4
AR0O OUTR R625 HPOUT_RT 1 2 3
10 OHM 1/10W FB608 120R 2
+
6
NC 100UF 16V C660 1 2 7
6.8NF 50V FB609 120R 1
PHONE JACK
HP_DET# 1 2
C651 FB610 120R
AL0O OUTL R626 HPOUT_LT
10 OHM 1/10W
+
C662 C663 C664

NC 100UF 16V C661 HP Detect NC/100N 16V
6.8NF 50V 10N 50V 10N 50V
H = > HP Detect
R628 R627 L = > Normal
NC 22K 1/16W NC 22K 1/16W
3 2014-07-07
Audio A-in/I2S/HP 715G6836
19760_509.eps
2015-Aug-08 back to
div.table
10-4-4 Speaker Amp
B04 Speaker Amp B04
12V_AMP DVDD3V3 3,4,5,7,8,9,10,11,12,13,14,15,16,17,18 GND

PVDD PVDD AMP3V3
3 12V_AMP 12V_AMP
FB602 DVDD3V3
1 2 3,4,5,8,9,10,11,13,15,16,17,18 DVDD3V3
1 2 FB603
120R
120R + + C614 C612 C610 C613 C615 C611
10UF 6.3V 20% 10UF 6.3V 20% 100NF 16V
C609
100uF 25V
C616
100nF 50V
C690
100uF 25V
C617
100nF 50V
100NF 16V 10UF 6.3V 20% 100NF 16V
GPIO & I2C Control
HP_AC_MUTE
HP_AC_MUTE 9
OSDA0
OSCL0 OSDA0 4
OSCL0 4
I2S Interface
AMP Mute AOMCLK
AOMCLK 5
DVDD3V3 AOBCK
AOLRCK AOBCK 5
AOSDATA0 AOLRCK 5
TP063 U601 AOSDATA0 5
R634
AMP_PDN 1 48 OUTB HPL_IN
NC 10K 1/16W 5% GND OUTB HPL_IN 5
HPR_IN
TP065 OUTA 2 47 OUTR HPR_IN 5
C623 33nF50V
OUTA BSTB OUTL OUTR 5
AMP_MUTE 33nF50V 3 46 AMP_MUTE OUTL 5
Q602 C691 C624 C625 33nF50V
100NF 16V BSTA BSTC AMP_MUTE 14
R633 NC MMBT3904
PVDD 4 45 OUTC
NC 10K 1/16W 5% PVDD OUTC FB604 120R 3A
5 44
PWM1 GND OUTA 1 2
6 43 OUTD L601
PWM2 OUTD C618 10uH C619
R635 HPL_IN 7 42 C628 33nF50V R605 470NF 16V
AMP_MUTE NC 22R 1/16W 5% AMP_PDN HPIL BSTD 18R 1/10W 5% C620
OUTL 8 41 PVDD 330pF 50V 1UF 16V FB605 120R 3A
HPOL PVDD
OUTR 9 40 C630 1UF 25V OUTB 1 2
HPOR GVDD_REG L602
HPR_IN 10 39 HP_AC_MUTE C622 10uH C621
HPIR HP_SD R606 470NF 16V CN601
6
11 38 C633 2.2nF 50V 18R 1/10W 5%
HPVSS SSTIMER 330pF 50V L+ 4
C634 1UF 25V 12 37 L- 3
L+
C635 100NF 16V L-
C636 CN AVDD_REG2 R+ 2
13 36 R- 1
R+
1UF 25V AMP3V3 R-
CP GND FB606 120R 3A
AMP3V3 14 35 CONN
5
HPVDD GND OUTC 1 2
15 34 AMP3V3 R609 L603 5/28
GND DVDD 10K +-1% 1/16W C627 10uH C626
16 33 R607 470NF 16V
C637 C638 FLTM TEST 18R 1/10W 5% C629
R610 17 32
47nF 16V 4.7nF 50V AMP_RESETN 330pF 50V 1UF 16V
470R 1/16W 5% FTLP RESET FB607 120R 3A
R611
C639 18 31 1K 1/16W 1%
4.7nF 50V AMP3V3 AVDD_REG1 NC C640 OUTD 1 2
R612 AMP3V3 19 30 R631 OSCL0 L604
470R 1/16W 5%
C641 AVDD SCL 33R 1/16W 5%
2.2UF C632 10uH C631
47nF 16V R613 ADR 20 29 R632 OSDA0 R608 470NF 16V
10K +-1% 1/16W
ADR SDA AMP3V3
33R 1/16W 5% 18R 1/10W 5%
AOMCLK 21 28 AOSDATA0 330pF 50V
MCLK SDIN1
22 27 AOBCK
ROSC SCLK R616
23 26 AOLRCK 10K +-1% 1/16W
GND LRCLK
24 25 AMP_PDN
DVDD_REG PDN
E-Pad
R614
18.2K OHM +-1% 1/16W
C642
4.7UF 10% 10V TAS5729MD
Heat Sink
49
HS601
2
1
NC/HEAT SINK
3 2014-07-07
Speaker Amp 715G6836
19760_510.eps
2015-Aug-08 back to
div.table
10-4-5 VGA
VGA
Audio/Video IO/SPDIF
B05 B05
VGA IN (V/T) U401C TP1109 3,4,5,6,8,9,10,11,12,13,14,15,16,17,18 GND

Analog Power
AB19 AE24 AL0O R1204 C1203 3,6 12V_AMP 12V_AMP
AB21 AIN1_L_AADC AL0_ADAC AD25 AR0O VGA_R VGA_RIN GND
3,10 +12V +12V
1
SCART1_L_IN AB18 AIN1_R_AADC AR0_ADAC AC24 2,3,4,5,7,8,9,10,11,12,13,14,15 GND
+5VSB
SCART1_R_IN AB22 AIN2_L_AADC AL1_ADAC AE25 R1207 NC 100R 1/16W 1% NC 10N 50V 3,9,10,11,12,15 +5V_SW +5V_SW
AB20 AIN2_R_AADC AR1_ADAC AD24 NC 0R05 1/16W
+5VSB
YPBPR0_L_IN
AIN3_L_AADC AL2_ADAC
AVDD1V2 3,9,16 +5VSB
AVDD1V2 2,9,12,13,14
YPBPR0_R_IN AC22 AC25 AVDD3V3
VGA_L_IN AC20 AIN3_R_AADC AR2_ADAC R1201 3,4,8,10,13,14 3V3SB 3V3SB
AIN4_L_AADC ZD1106 C1208 DVDD3V3
VGA_R_IN AB23 NC 75R 1/16W 1% AVDD33_ADAC 3,4,5,6,8,9,10,11,13,15,16,17,18 DVDD3V3
AIN4_R_AADC AE6 ARC
ALIN NC 10PF 50V SPDIF OUT SCART1_R_IN
W14 3,8,13,15
8 SCART1_R_IN AVDD1V2
SCART1_L_IN
AVDD1V2
R1220 MPXP NC/AZ5123-01H TP1110 8 SCART1_L_IN 3,17 VCCK
C614 C611 C616 VCCK
NC 4.7K 1/16W
2
10UF 10V 100NF 16V 10NF 50V C604
R1219 TP1103 CN101 C1206
19
17
TP1101 AD22
AVDD33_AADC
Y18
TP1102
AVDD33_AADC ASPDIFO0
AB4
AC8
SPDIF_OUT
TP1104 TP1105 VGA_SOG SOG0 R600 100NF 16V
8 VGA_R_IN
VGA_R_IN
AVSS33_AADC AOBCLK_D NC D-SUB 15P SPDIFOUT SPDIF_OUT VGA_L_IN
NC 4.7K 1/16W AVSS33_AADC AOBCK R1208 8 VGA_L_IN
---><---|>
AD7 AOLRCK_D NC 1.5nF 50V
AE23 AOLRCK AD8 6 VGA_SCL
AVDD33_ADAC AOMCLK_D NC 0R05 1/16W 240R 1/10W 5% 8 7 VGA_SCL AL0O
AVSS33_ADAC W19 AVDD33_ADAC AOMCLK AD6 VGA_RX
AOSDATA0_D 11 1 AL0O VGA_SDA
AR0O
100R 1/10W 5%
AVSS33_ADAC AOSDATA0 AC7
TP1106 8 7 VGA_SDA
AR0O
AOSDATA1
AVDD3V3 7 AVDD3V3 R601 VGA_VS
AVSS33_CLN AA18 C605 8 8 VGA_VS SOY0
VGA_SDA_12 AVSS33_CLN AE22 AVDD33_HPA
12 2 AVDD33_AADC AVDD33_HPA VGA_G C1204 VGA_GIN SOY0 VGA_HS
AOBCLK_D
33pF 50V 8 7 VGA_HS
1
VMID_AADC AD23 AVDD33_HPA V17 AVSS33_HPA 8 AOBCLK_D VGA_BIN
AOLRCK_D
VMID_AADC AVSS33_HPA
13 3 R1209 R1205 NC 10N 50V 8 7 VGA_BIN
AOLRCK_D AOMCLK_D
VGA_HSYNC SOG0
9 C615 C613 NC 0R05 1/16W C612 NC 100R 1/16W 1% 8 77 AOMCLK_D
SOG0
AOSDATA0_D
AOSDATA0_D
VGA_GIN
MT5580MPOI 10UF 10V 100NF 16V 100NF 16V
VGA_VSYNC 14 4 VGA_TX 8 VGA_GIN VGACOM
IF_AGC
ZD1107
812,14 VGACOM
IF_AGC
1
10 R1202 C1207 Y0P
VGA_RIN
VGA_SCL_15 15 5 TP1108 NC 75R 1/16W 1%
8 88 Y0P
VGA_RIN
COM0
COM0
C610 C606 PB0P
NC 10PF 50V 8 PB0P PR0P
100NF 16V 1uF 10V NC/AZ5123-01H R1212 8 PR0P
1
1
HSYNC
ZD1105 NC 100R 1/16W 1% C1210 VGACOM 8 HSYNC VSYNC
18
16
2
8 VSYNC RP
Audio NC/AZ5123-01H R1211 Analog Power NC 10N 50V 8 RP GP
ZD1101 ZD1102 ZD1103 ZD1104 ZD1123
YPbPr & Audio IN NC 0R05 1/16W
8
8
GP
BP
BP
AVDD1V2 AVDD3V3 VGACOM
8 VGACOM SOG
2
AVDD12_RGB AVDD33_DEMOD 8 SOG VGASDA
CN112
RCA JACK
TP1107 TP1111 8 VGA_IN_R
VGASDA VGA_IN_R
VGASCL 5
NC/AZ5123-01H NC/AZ5123-01H NC/AZ5123-01H NC/AZ5123-01H NC/AZ5123-01H 088G353GFF1ACL 5 11 R1206
8 VGA_IN_L
VGASCL TU_FAT_IN2+
VGA_IN_L 5
6 12 C600 C1205 VGA_BIN 14 TU_FAT_IN2+
C
PR_IN_1 SPDIFOUT TU_FAT_IN2-
F
C602
2
2
100NF 16V 100NF 16V 14 TU_FAT_IN2-
3 9 R1210 NC 100R 1/16W 1% NC 10N 50V OSCL2
1
NC 0R05 1/16W 12,14 OSCL2
4 10
E
PB_IN_1 YPbPrR_IN OSDA2
AVDD1V2 AVDD3V3 12,14 OSDA2
U401J
1 7 R1203
AD19 AC11 HSYNC 2 8 C1209
D
A
ADCINP_DEMOD Y_IN_1 YPbPrL_IN
NC 75R 1/16W 1% AVDD12_DEMOD AVDD33_VIDEO CVBS3P
ADCINN_DEMOD AE19 ADCINP_DEMOD HSYNC AC10 VSYNC ZD1108 NC 10PF 50V 8 CVBS3P
ADCINN_DEMOD VSYNC AB13 RP
RP AE12 R1217
GP C601 C603 C608 AVDD3V3
IF_AGC
VGA_HSYNCM19
R605 10K 1/16W 5% GP AB12 BP VGA_HS 100NF 16V 100NF 16V 2,4,5,9,10,11,12,13 AVDD3V3
IF_AGC BP 1uF 10V
M20 AD12 NC 100R
VGACOM 1/16W 5% NC/AZ5123-01H ARC
C621 RF_AGC COM AC12 SOG 13 ARC
SOG
2
47NF 16V AE9 VGASCL
VGA_VSYNCAC17
AVDD12_RGB VGA_SCL AD9 R1218
VGASDA VGA_VS
AVSS12_RGB V13 AVDD12_RGB VGA_SDA NC 100R 1/16W 5%
AVSS12_RGB
AD14
2
COM1
COM1 AE14 PB1P VGA_TX R1213 NC 33R
AE18 PB1P AC14
ZD115
AVDD33_DEMOD ZD116 PR1P
AVSS33_DEMOD
NC BZT52-B5V6S
V16 AVDD33_DEMOD
AVSS33_DEMOD
PR1P
Y1P
AB14
AC13
Y1P YPBPR IN VGA_RX R1214 NC 33R
SOY1
NC BZT52-B5V6S SOY1
AVDD12_DEMOD AD18 VGA_SDA_12 R1215 NC/33R VGA_SDA
1
AVSS12_DEMOD AC18 AVDD12_DEMOD AC16 COM0 C1036 47NF 16V

AVSS12_DEMOD COM0 AD16 PB0P CVBS1P
PB0P AE16 PR0P VGA_SCL_15 R1216 NC/33RR1050 100R 1/16W 5% VGA_SCL
AVDD33_VIDEO AD17 PR0P AC15 Y0P
AVSS33_VDAC V14 AVDD33_VIDEO Y0P AB15 SOY0 C1033 1.5NF 50V
AVSS33_VDAC_BG W15 AVSS33_VDAC SOY0 SOY1 C1039 R1087
AVSS33_VDAC_BG R1113 10R 1/16W 5% YPbPrR_IN YPBPR0_R_IN
---><---|>
C1034 10NF 50V
AA14 R1071 75 OHM +-5% 1/16W Y_IN_1 R1044 Y1 Y1P C1037 10UF 10V 30Kohm 1/16W +/-5%
AVSS33_CVBS_1 W17 VDACX_OUT Y14
56R 1/16W 1%
R1073 75 OHM +-5% 1/16W R1043 100R 1/16W 5% NC/10N 50V
-------><-------
AVSS33_CVBS_2 Y17 AVSS33_CVBS_1 VDACY_OUT W16 18R 1/16W 5%

AVSS33_CPUPLL G15 AVSS33_CVBS_2 CVBS0P AB16 CVBS1P
AVSS33_CPUPLL CVBS1P AA16 R1047 C618
CVBS2P Y16 CVBS3P 10PF 50V
CVBS3P AA15 CVBS_COM
CVBS_COM C617 10NF 50V
M21 OSCL2 C607
TP1116 COM1
OSCL2 M22 OSDA2 R1039 0R05 1/16W R1049 100R 1/16W 5%
OSDA2 1uF 10V
C1201 NC 2.2uF 10V VGA_IN_R C1040
Video
CN606 MT5580MPOI R1227 NC 30K OHM
YPbPrL_IN
R1088
YPBPR0_L_IN
---><---|>
C620 10NF 50V
2 PB_IN_1 R1040 PB1 PB1P 10UF 10V 30Kohm 1/16W +/-5%
3 VGA_IN_L C1038
C1202 NC 2.2uF 10V
56R 1/16W 1%
R1041 100R 1/16W 5%
-------><-------
4 18R 1/16W 5% NC/10N 50V

R1228 NC 30K OHM
1 R1045
2
NC PHONE JACK C609

C1212 ZD1110 TP1117 10PF 50V
2
C1211 ZD1111
IF BPF
-------><-------
NC 470pF 50V
56R 1/16W 1%
NC 470pF 50V
NC VPORT0603100KV05
NC VPORT0603100KV05
R1046
1
C1035
R603 R1042 10PF 50V
1
TU_FAT_IN2+ ADCINP_DEMOD 18R 1/16W 5% C619 10NF 50V

PR_IN_1 PR1 PR1P
51OHM 1/16W +/-5% R1048 100R 1/16W 5%
C622
47PF 50V
R604
TU_FAT_IN2- ADCINN_DEMOD
51OHM 1/16W +/-5%

C623
47PF 50V
C
3 2012-12-15
2014-07-07
Audio/Video IO/SPDIF
VGA 715G5713
715G6836
19430_519_130114.eps
19760_511.eps
130114
2015-Aug-08 back to
div.table
10-4-6 Video YPbPr/CVBS
B06 Video YPbPr/CVBS B06

Merged Analog 3.3V Power
Analog 1.2V Power 3,4,5,6,7,9,10,11,12,13,14,15,16,17,18 GND
AVDD1V2
3V3SB 3V3SB 3V3SB
U401D 3,4,10,13,14 3V3SB
V5 R1301 3,13,15 AVDD1V2 AVDD1V2
NC 33R 1/16W 5% VGA_SCL 20mil
L16 VGA_SCL V4 R1302 3,4,5,6,9,10,11,13,15,16,17,18 DVDD3V3 DVDD3V3
TP405 TP NC 33R 1/16W 5% VGA_SDA AVDD12_DEMOD AVDD33_VIDEO_STB AVDD33_RGB_STB
IFAGC_Scaler J15 RF_AGC VGA_SDA V10 VGA_VS
IF_AGC VSYNC U10 VGA_HS
ADCINN_DEMOD Y19 HSYNC V11 VGA_BIN
ADCINP_DEMOD W18 ADCINN_DEMOD
ADCINP_DEMOD
BP
SOG
U11 SOG0
C104 C101 C102
C103 YPbPr Audio Input
W12 VGA_GIN 100NF 16V NC/100N 16V 100NF 16V 1UF 10V
AVDD12_DEMOD 1 2 Y20 GP Y12 VGACOM YPBPR_R_IN
AVDD12_DEMOD COM V12 VGA_RIN YPBPR_L_IN YPBPR_R_IN 5
FB102 120R
RP YPBPR_L_IN 5
U12 SOY1
SOY1 V13 Y1P
Y1
COM1
U13 COM1 CVBS Audio Input
W14 PB1P DVDD3V3
PB1 Y14 PR1P CVBS_R_IN
PR1 CVBS_L_IN CVBS_R_IN 5
AVDD33_RGB_STB V17 V14 CVBS_L_IN 5
10mil
AVDD33_RGB_STB SOY0 U14 R121
Y0 H = > Pr Plug-in (YPbPr)
AVDD33_VIDEO_STB U17 V15
AVDD33_VIDEO_STB COM0
PB0
U15
NC 47K 1/16W 5% L = > Pr Plug-out (AV) Control Interface
W16 R122
AVSS33_CLN N14 PR0 PR_DET PR1_DET PR1_DET
AVSS33_RGB T12 AVSS33_CLN V18 CVBS0P 10 PR1_DET
AVSS33_RGB CVBS0 Y17 NC 100R 1/16W 5%
AVSS33_VIDEO T14 CVBS1 Y16 CVBS_COM
AVSS33_VIDEO CVBS_COM
W17 TP TP407 VGA_SCL
VDAC_OUT VGA_SDA VGA_SCL 7
C105
1UF 10V VGA_VS VGA_SDA 7
VGA_HS VGA_VS 7
MT5561LVNT
VGA_BIN VGA_HS 7
SOG0 VGA_BIN 7
VGA_GIN SOG0 7
VGACOM VGA_GIN 7
VGA_RIN VGACOM 7
VGA_RIN 7
IF Interface
ADCINN_DEMOD
ADCINP_DEMOD ADCINN_DEMOD 11
ADCINP_DEMOD 11
YPbPr Video/Audio Input

Control Interface
R102 C106 SOY1 IFAGC_Scaler
NC 10R 1/16W 1% NC 1.5nF 50V IFAGC_Scaler 11
CN116 13 Y_IN_1 R106 R105 C108 Y1P Side CVBS Video/Audio input
1
12 NC 0R05 1/10W NC 100R 1/16W 5% NC 10N 50V

E 11 R107
10 PB_IN_1 C109
ZD101 CN102 R1001 R1002 C1002
D 9 2 AV_CVBS_IN CVBS0P
NC/AZ5123-01H NC 10PF 50V
1
8 PR_IN_1 NC 75R 1/16W 1% 0R05 1/10W 100R 1/16W 5%
7 PR_DET A 1 47nF 16V
C 6 R108 R109 COM1
C110
2
5 NC 0R05 1/10W NC 100R 1/16W 5% NC 10N 50V 4 AV_AudioLIN R1003 C1001

75R 1/16W 1% 47pF 50V
B 4 B 3 ZD106
3 R110 R112 C111 PB1P AZ5123-01H
1
2 NC 0R05 1/10W NC 100R 1/16W 5% NC 10N 50V 7 AV_AudioRIN
2
A 1 6
C 5
NC/RCA JACK R113
C112
ZD102 C1003 2.2UF AV_L_In R1004 CVBS_L_IN
1
NC 75R 1/16W 1%
NC/AZ5123-01H NC 10PF 50V JACK 30K OHM
R1005
12
C113 C1214
NC/0R05 1/16W 330PF 50V
ZD103 NC 10PF 50V ZD107
NC/AZ5123-01H R114 AZ5123-01H
1 2
NC 75R 1/16W 1% R1006
C1004 2.2UF AV_R_In CVBS_R_IN
R115 R117 30K OHM
C114 PR1P
2
NC 0R05 1/10W NC 100R 1/16W 5% NC 10N 50V

C1215
330PF 50V
YPbPr1L_IN C115 R118 YPBPR_L_IN ZD108
NC 2.2uF AZ5123-01H
NC 30K OHM
2
YPbPr1R_IN C116 R119 YPBPR_R_IN
NC 2.2uF
1
NC 30K OHM
C117
C118
R120
NC 1N 50V
NC 1N 50V
NC/0R05 1/16W
ZD104 ZD105
2
NC/AZ5123-01H NC/AZ5123-01H
3 2014-07-07
Video YPbPr/CVBS 715G6836
19760_512.eps
2015-Aug-08 back to
div.table
10-4-7 SPDIF/Mute contorl
B07 SPDIF/ Mute contorl B07
DVDD3V3
+5VSB BAS316 AC OFF Audio Mute for SCART 10mil

3,4,5,6,7,8,10,11,12,13,14,15,16,17,18 GND
D602
3,4,5,6,8,10,11,13,15,16,17,18 DVDD3V3 DVDD3V3
DVDD3V3 R657
10K +-1% 1/16W 3,7,16 +5VSB +5VSB
DC OFF R664
+ HP_AC_MUTE 3,10,11,12,15 +5V_SW +5V_SW
+5V_SW 1K 1/16W 1% A_MUTE1
C681 R658
22uF 16V 4.7K 1/16W D601 R659
3
R679 2.2K 1%
Q601
LMBT3904LT1G
C678
10UF 6.3V 20% GPIO Control Mute
5.1K 1% A_MUTE HP_MUTE 2 BAV70 HP_MUTE
10 HP_MUTE
R660
R668 C680 4.7K 1/16W C679
NC/10UF 6.3V 20%
470R 1/16W 5%
Q603
LMBT3904LT1G
HP_MUTE
H: MUTE
100NF 16V
Mute Control
L: UN-MUTE
R669 HP_AC_MUTE
6 HP_AC_MUTE
10K +-1% 1/16W
SPDIF_OUT
5 SPDIF_OUT
SPDIF OUT
C685 R654 CN604 RCA JACK
SPDIF_OUT 180R 1/16W 5% 2
1
100NF 16V ZD602

R624 AZ5123-01H
100R 1/16W 5% C686
33P 50V 1
2
15mil
+5V_SW
R656 CN603
NC 33R 1/16W 5% 3
2 VIN
1 VCC
C677 GND
NC 100N 16V NC CONNNECTOR
3 2014-07-07
SPDIF/ Mute contorl 715G6836
19760_514.eps
2015-Aug-08 back to
div.table
10-4-8 LVDS_Keypad_IR
LVDS_Keypad_IR
B08 B08
U401G
A2 TX_AO0P 3,4,5,6,7,8,9,11,12,13,14,15,16,17,18 GND
AO0P B2 TX_AO0N
E4 AO0N C3 3 +12V +12V
DEMOD_RST TX_AO1P LVDSVDD FB401
F2 TCON0 AO1P D3 3,9,11,12,15 +5V_SW +5V_SW
TX_AO1N Panel_VCC
C2 TCON1 AO1N C4 1 2 3,4,8,13,14 3V3SB 3V3SB
HP_MUTE TX_AO2P
E3 TCON2 AO2P D4 3,4,5,6,8,9,11,13,15,16,17,18 DVDD3V3 DVDD3V3
TX_AO2N
C1 TCON3 AO2N C5 120R
SW_CTL TX_AO3P C409 + R409 DVDD3V3
PR1_DET D1 TCON4 AO3P D5 TX_AO3N C410 4.7K 1/8W
AC_DET F3 TCON5 AO3N A4 TX_AOCKP
HP_DET# D2 TCON6
TCON7
AOCKP
AOCKN
B4 TX_AOCKN CN408
100UF 35V 100NF 16V
R427 GPIO Interface
ARC_on/off F1 C6 TX_AE0P NC/1K 1/16W LED_POWER_RED
TCON8 AE0P D6 TX_AE0N 2 1 LED_PWR_GREEN LED_POWER_RED 4,14
AE0N A6 TX_AE1P
LED_POWER_RED LED_PWR_GREEN 4 3 OIRI LED_PWR_GREEN 4,14
AE1P B6 TX_AE1N 6 5 Panel_Select KEY_UP_DN_DCSW OIRI 4
AE1N H = > Standby H = > Power ON KEY_UP_DN_DCSW 14
C7 TX_AE2P L = > Power ON L = > Standby 8 7 KEY_MENU_L_R_SOURCE
AE2P D7 TX_AE2N TX_AO0P 10 9 TX_AO0N LVDS_PWR_EN KEY_MENU_L_R_SOURCE 14
AE2N C8 TX_AE3P TX_AO1P 12 11 TX_AO1N LVDS_PWR_EN 14
AE3P D8 TX_AE3N TX_AO2P 14 13 TX_AO2N R428
AE3N TX_AOCKP 16 15 TX_AOCKN NC 0R05 1/16W
TX_AO3P 18 17 TX_AO3N DEMOD_RST
20 19 HP_MUTE DEMOD_RST 18
TX_AE0P 22 21 TX_AE0N PR1_DET HP_Mute 9
MT5561LVNT TX_AE1P 24 23 TX_AE1N AC_DET PR1_DET 8
TX_AE2P 26 25 TX_AE2N ARC_on/off AC_DET 3
TX_AOCKP 28 27 TX_AOCKN SW_CTL ARC_on/off 16
TX_AE3P 30 29 TX_AE3N KEY_On_board SW_CTL 11
AC_Off KEY_On_board 14
C474 NC/100pF 50V R482 NC/0R05 1/16W HP_DET# AC_Off 3
HP_DET# 5
CONN
R483 NC/191K OHM 1% 1/16W

U403
R484 C475
NC/10K 1/10W 1% 1 6 16Vto12V
FB BS NC/0.1uF 50V
IR/KEY BOARD 3V3SB 3V3SB
R485 L402
2 5
EN LX
NC/36K 1% NC/4.7uH
+12V C478 C479 + C480 Q408 Q409
NC/20K OHM 1/16W 1%
NC 100UF 25V
R486
NC/22UF 10V NC/22UF 10V NC AO3401 NC AO3401

3 4 R488 0R051/8W
GND IN LED-R LED-B
NC/SY8104ADC
NC/10N 50V C476
C477
10UF 16V Q421 LED_POWER_RED Q422 LED_PWR_Blue
NC BC847C NC/BC847C
R4052
R4050 R4054 NC 1.2K 1/16W R4055
NC 1.2K 1/16W NC/10K NC/10K
R487 NC/40.2K 1/16W 1%
AC_Off
3V3SB
3V3SB
1
FB403
R430 R431 30R
LVDS POWER Control panel_power
6.8K 1/16W 6.8K 1/16W
2
LED_PWR_GREEN R433 100R 1/16W 5% LED-B
LED_POWER_RED R434 100R 1/16W 5% LED-R 1 2

16Vto12V OIRI R435 100R 1/16W 5% IR 3 4
1 2 IR_PWR 5 6
FB408 NC/220R Q405 LVDSVDD 7 8
+5V_SW KEY_UP_DN_DCSW R437 100R 1/16W 1% 9 10
1 2 KEY_MENU_L_R_SOURCE R438 100R 1/16W 1% Joy_Key
FB402 NC/220R NC AO3401A
+12V CN401
1 2 NC CONN
FB404 220R 3V3SB
C414 100NF 16V
C418 100NF 16V
C415 NC 100N 16V
C416 NC 100N 16V
C417 NC/100N 16V
C419 100NF 16V

Q401
1 8
R432 C411 2 S D 7
47K 1/16W 5% 470NF 16V 3 S D 6 R492
R436 4 S D 5 SW401 NC 4.7K 1/16W
G D C412 Panel_VCC 3 4
H = > LVDS POWER ON 47K 1/16W 5%
SM4310PSKC 1 2 R490 KEY_On_board
L = > LVDS POWER OFF 100NF 16V NC 100R 1/16W 1%
NC SW R491 KEY_UP_DN_DCSW
NC 100R 1/16W 5%
9
R439 CN406
LVDS_PWR_EN Q402
7
2.2K 1% LMBT3904LT1G R440 6 Joy_Key
NC/470R 1/10W 1% 5 IR_PWR
R441 4
4.7K 1/16W C413
NC/100N 16V 3 IR
2 LED-B
1 LED-R
R444 Q403
NC/2N7002K CONN
8
NC/1K 1/16W 1%
3 2014-07-07
LVDS_Keypad_IR 715G6836
19760_515.eps
2015-Aug-08 back to
div.table
10-4-9 TUNER
TUNER
B09 B09
3,4,5,6,7,8,9,10,12,13,14,15,16,17,18 GND
TUNER3.3V
3,9,10,12,15 +5V_SW +5V_SW
+5V_SW 3,4,5,6,8,9,10,13,15,16,17,18 DVDD3V3 DVDD3V3
FB104 U113 TUNER3.3V
AZ1117CH-3.3TRG1
R127
1K 1/16W 1% 1 2 3
VIN VOUT
2 R116 IF InterfaceFAT_IN-
C141
ADJ(GND)
220R
C142
0R05 1/10W FAT_IN+ ADCINN_DEMOD 8
ADCINP_DEMOD 8
D102 C190
D_IFP
BAS316 D_IFP 18
D_IFN
4
Notch_On1
10UF 6.3V 20%

1UF 10% 16V
100NF 16V
D_IFN 18
4
C136
FCN101
1nF 50V
L102 82nH
Control Interface
IFAGC_Scaler
IFAGC_Scaler 8
C132 C134
1nF 50V 1nF 50V OSCL1
5 OSDA1 OSCL1 4,18
3
ANT OSDA1 4,18
C137 TUNER_SCL
4 1nF 50V 18 TUNER_SCL TUNER_SDA
4 3 L101 C158 18 TUNER_SDA IFAGC_Toshiba_demo
3 2 NC 2.2nH D101 1nF 50V 18 IFAGC_Toshiba_demo SW_CTL
2 1 BAV99 10 SW_CTL
1
1
R128 DVDD3V3
2.2K 1%
D103
Notch_On2 BAS316
C160 R159 R160

RF CONN 1nF 50V
2.2K 1% 2.2K 1%
R168 NC 0R05 1/16W
L104
T_SCL R162 100R 1/16W 5% R449 0R05 1/16W TUNER_SCL
T_SDA R165 100R 1/16W 5% R450 0R05 1/16W TUNER_SDA
C139 C154 C155

10N 50V 22PF 50V 22PF 50V
R1089 NC/0R05 1/16W OSCL1
R1090 NC/0R05 1/16W OSDA1
7
U102
GND6
RF2
GND5
C140
R129 NC/0R05 1/16W
10 6 10N 50V L106 L107 C120
TUNER3.3V R130 NC/1MOHM 1/16W +/-5% 11 C2 GND4 8.2NH 27nH 1nF 50V
12 C1 5 R169 LNA_INP
C146 NC/10N 50V SW_CTL VDD RFC NC 0R05 1/16W
13 4
PADDLE GND3
GND1
GND2
C147 NC/100N 16V TUNER3.3V C169 C121
RF1
C192 5P6 50V 1nF 50V
LNA_INN
NC/PE42750 4.7PF 50V
3
FCN102
C159 C168 L103

NC/1nF 50V NC/1nF 50V 27nH
5
3
ANT
4
4 3 L105
3 2 NC 2.2nH D104
2 1 NC/BAV99
1
1
TUNER3.3V
R151
10K +-1% 1/16W
IFAGC R150 IFAGC_Scaler
2
R149 0R05 1/16W R123 X102
C143 1K 1/16W 1% C144 510K 1% XTALN 1 3 XTALP
10N 50V 47nF 16V +1V8TUNER
NC/RF CONN 16MHZ
4
RESET
C164 C165
15PF 50V 15PF 50V
C128
1UF 10V
R153 C166
10K +-1% 1/16W 10N 50V
R152 IFAGC_Toshiba_demo XTALP
TUNER3.3V
0R05 1/16W XTALN
C145
22N 25V
25
24
23
22
21
20
19
U104
C133 C125
AS
VDD_1p8
RESET_N
XTAL_P
E-PAD
XTAL_N
GND_XTAL
100NF 16V
TUNER3.3V 10UF 6.3V 20%
R133
560R 1/16W 1% MxL661 TUNER3.3V
1 18
Notch_On1 1 2 +1V8TUNER LNA_INP 2 VDD_3p3 CLK_OUT 17 T_SDA
FB108 1000R LNA_INN 3 LNA_INP SDA 16 T_SCL

FB103 1 2 1000OHM 4 LNA_INN SCL 15
R155 R1029 Notch_On2 1 2 5 VDD_1p8 VDD_IO 14
IFOUT1P R101 C148 51R 1/16W 5% FAT_IN+ FB109 1000R 6 AGC_2/GPO_3 GND_DIG 13
1UF 10% 16V AGC_1 VDD_1p2
0R05 1/16W 100R 1/16W 5%
C197 C124
IF_OUTN_2/GPO_2
C122 C123 C126
IF_OUTP_2/GPO_1
R156 100NF 16V
330R 1/16W 1% 2.2nF 50V 100NF 16V 47pF 50V 47pF 50V
IF_OUTN_1
IF_OUTP_1
R1030
VDD_3p3
VDD_1p8
IFOUT1N R104 C149 R157 51R 1/16W 5% FAT_IN-
1UF 10% 16V
0R05 1/16W 100R 1/16W 5% R124
C150 C151 IFAGC
C163 C191 C161 C162
1K 1/16W 1%
NC/47pF 50V NC/47pF 50V
7
8
9
10
11
12
22PF 50V 22PF 50V NC/47pF 50V NC/47pF 50V MxL661-AG-R +1V8TUNER
C167 C135
100NF 16V 100NF 16V TUNER3.3V
R1111 R161
C127
C152 0R05 1/16W 0R05 1/16W D_IFP 100NF 16V C131
IFOUT1P C130 4.7NF 50V 1UF 10V
C153
1UF 10% 16V
NC/22pF 50V R164 IFOUT1N C129 4.7NF 50V
NC 150R 1/16W 1%
R1112 R167
C156 0R05 1/16W 0R05 1/16W D_IFN
1UF 10% 16V C157

NC/22pF 50V
3 2014-07-07
TUNER 715G6836
19760_516.eps
2015-Aug-08 back to
div.table
10-4-10 DDR3
B10 DDR3 B10
3,4,5,6,7,8,9,10,11,13,14,15,16,17,18 GND
3,9,10,11,15 +5V_SW +5V_SW
DDRV
U401A
N1 DRAM POWER DDRV Main Chip Ref Voltage.

+5V_SW DDRV
DDRV N2 DDRV
DDRV N3 U411
DDRV L401
N4 1 5
DDRV N5 2 VIN LX
DDRV GND 2.2uH
N6 3 4
DDRV EN VFB R455 C425
P1 RVREF
R1 R456
C428 R480 G5695T11U C426 C427 1K 1/16W 1% NC/100N 16V
DDRVREF 0R05 1/16W R460 33K 1/16W 1% 22UF 6.3V 100NF 16V
P2 ZQ R457 2.2UF
ZQ 240R 1% R2 22K 1% RVREF
H8
TN_MEMPLL J8
TP_MEMPLL
R410 R461
C429
MT5561LVNT 100K 1% 1K 1/16W 1% NC/100N 16V
DRAM# Bypass Cap

DDRV
C430 C439
10UF 6.3V 20% C196 C433 C434 C435 C436 C437 C432 C441 C438 C440
NC/4.7UF 10% 10V 100NF 16V 100NF 16V 1UF 10V 100NF 16V 100NF 16V 100NF 16V 1UF 10V 100NF 16V NC/10UF 6.3V 20% 4.7UF 10% 10V
3 2014-07-07
DDR3 715G6836
19760_517.eps
2015-Aug-08 back to
div.table
10-4-11 HDMI/MHL
B11 HDMI/MHL B11

3,4,5,6,7,8,9,10,11,12,14,15,16,17,18 GND
3,9,10,11,12,15 +5V_SW +5V_SW

3,7,9,16 +5VSB +5VSB
3,4,8,10,14 3V3SB 3V3SB
3,4,5,6,8,9,10,11,15,16,17,18 DVDD3V3 DVDD3V3
3,8,15 AVDD1V2 AVDD1V2
REAR HDMI 2
(with ARC) I2C & UART Interface
CN502 HDMI_SCL2
U401E HDMI_SDA2 HDMI_SCL2 16
P20 22 1 RX_2_2 HDMI_SCL2/RX HDMI_SDA2 16
RX_0_CB W7 HDMI_1_RX_CB P19 23 SHELL3 D2+ 2 HPWR2 HDMI_SDA2/TX HDMI_SCL2/RX 16
RX_0_C Y7 HDMI_0_RX_CB HDMI_1_RX_C P18 SHELL4 D2 Shield 3 RX_2_2B HDMI_SDA2/TX 16
RX_0_0B V7 HDMI_0_RX_C HDMI_1_RX_0B P17 D2- 4 RX_2_1
RX_0_0 V8 HDMI_0_RX_0B HDMI_1_RX_0 N18 D1+ 5 OPWR2_5V
HDMI_0_RX_0 HDMI_1_RX_1B D1 Shield
R504
R505
C511
RX_0_1B U9 N17 6 RX_2_1B
RX_0_1 V9 HDMI_0_RX_1B
HDMI_0_RX_1
HDMI_1_RX_1
HDMI_1_RX_2B
M20 D1-
D0+
7 RX_2_0 Control Interface
RX_0_2B W9 M19 8
HDMI_0_RX_2B HDMI_1_RX_2 D0 Shield
10K 1/16W 5%
10K 1/16W 5%
100N 16V
RX_0_2 Y9 9 RX_2_0B
HDMI_0_RX_2 J18 D0- 10 RX_2_C UART_SEL
HDMI_1_SCL K14 24 CK+ 11 UART_SEL 16
HDMI_SCL0 U7 HDMI_1_SDA L17 SHELL5 CK Shield 12 RX_2_CB
HDMI_SDA0 V6 HDMI_0_SCL HDMI_1_HPD CK- 13 CEC_A2
HDMI_0M_HPD W5 HDMI_0_SDA M18 RX_2_CB CE Remote 14 R503 UART_SEL
HDMI_0_HPD HDMI_2_RX_CB M17 RX_2_C NC 15 HDMI_SCL2_IN 0R05 1/10W R506 22R 1/16W 5% HDMI_SCL2/RX
HDMI_2_RX_C L18 RX_2_0B DDC CLK 16 HDMI_SDA2_IN R507 22R 1/16W 5% HDMI_SDA2/TX
AVDD33_HDMI R10 HDMI_2_RX_0B K18 RX_2_0 DDC DATA 17 R508
AVDD33_HDMI HDMI_2_RX_0 K20 RX_2_1B GND 18 OPWR2_5V 47K 1/16W 5%
AVDD12_HDMI_0 Y5 HDMI_2_RX_1B K19 RX_2_1 +5V 19 3V3SB
AVDD12_HDMI_1 H20 AVDD12_HDMI_0 HDMI_2_RX_1 J20 RX_2_2B HP DET 20
AVDD12_HDMI_1 HDMI_2_RX_2B SHELL1
ZD514
ZD515
ZD516
ZD517
J19 RX_2_2 21 R509
1
HDMI_2_RX_2 SHELL2 910R 1/16W
C509 NC/100N 16V

C510 NC/100N 16V
R512
J17 HDMI_SCL2 75 OHM 1/16W R514
HDMI_2_SCL J14 HDMI_SDA2 HDMI CONN HDMI_2M_HPD
HDMI_2_SDA J16 HDMI_2M_HPD 10K 1/16W 5%
HDMI_2_HPD_CBUS K15 Q504
MHL_SENCE
K16 CEC BC847C Q506
2
HDMI_CEC NC/AZ5123-01H R513
100K1/16W BC847C
MT5561LVNT
Analog Power Merged Analog Power

DVDD3V3 AVDD1V2 AVDD1V2
AVDD33_HDMI AVDD12_HDMI_0 AVDD12_HDMI_1 REAR HDMI 1

C502
C501 C503 100NF 16V CN501
100NF 16V 100NF 16V
22 1 RX_0_2
23 SHELL3 D2+ 2 HPWR0
SHELL4 D2 Shield 3 RX_0_2B
D2- 4 RX_0_1
D1+ 5 OPWR0_5V
C504
D1 Shield
R510
R511
6 RX_0_1B
D1- 7 RX_0_0
D0+ 8
D0 Shield
10K +-1% 1/16W
10K +-1% 1/16W
100NF 16V
9 RX_0_0B
HDMI CEC D0-
CK+
10 RX_0_C
24 11
SHELL5 CK Shield 12 RX_0_CB
CK- 13 CEC_A0
ZD501 CE Remote 14
1 2 CEC_A2 1 2 NC 15 HDMI_SCL0_IN R519 100R 1/16W 5% HDMI_SCL0
FB501 DDC CLK 16 HDMI_SDA0_IN R520 100R 1/16W 5% HDMI_SDA0
AZ5123-01H 120R DDC DATA 17
HDMI_CEC R501 CEC GND 18 OPWR0_5V R560 47K 1/16W 5%
100R 1/16W 5% +5V 19 3V3SB
ZD518 HP DET 20
SHELL1
ZD504
ZD505
ZD506
ZD507
1 2 CEC_A0 1 2 21 R524
1
FB503 SHELL2 910R 1/16W
120R
C505 NC/100N 16V
C506 NC/100N 16V
AZ5123-01H R561
75 OHM 1/16W R525
HDMI CONN HDMI_0M_HPD
10K +-1% 1/16W
Q502
R502
100K 1% BC847C Q503
ESD protcetion
2
2
NC/AZ5123-01H
BC847C
U501 U502
RX_0_CB1 10 RX_0_CB RX_0_1B1 10 RX_0_1B
RX_0_C 2 CH1 NC 9 RX_0_C RX_0_1 2 CH1 NC 9 RX_0_1
3 CH2 NC 8 3 CH2 NC 8
RX_0_0B4 VN VN 7 RX_0_0B RX_0_2B4 VN VN 7 RX_0_2B
RX_0_0 5 CH3 NC 6 RX_0_0 RX_0_2 5 CH3 NC 6 RX_0_2
CH4 NC CH4 NC
AOZ8804DI AOZ8804DI
ESD protcetion
U506 U507
RX_2_CB1 10 RX_2_CB RX_2_1B1 10 RX_2_1B
RX_2_C 2 CH1 NC 9 RX_2_C RX_2_1 2 CH1 NC 9 RX_2_1
3 CH2 NC 8 3 CH2 NC 8
RX_2_0B4 VN VN 7 RX_2_0B RX_2_2B4 VN VN 7 RX_2_2B
RX_2_0 5 CH3 NC 6 RX_2_0 RX_2_2 5 CH3 NC 6 RX_2_2
CH4 NC CH4 NC
AOZ8804DI AOZ8804DI
3 2014-07-07
HDMI/MHL 715G6836
19760_518.eps
2015-Aug-08 back to
div.table
10-4-12 GPIO
B12 GPIO B12
3,4,5,6,7,8,9,10,11,12,13,15,16,17,18 GND
3,4,8,10,13 3V3SB 3V3SB
LVDS_PWR_EN
BL_ON/OFF LVDS_PWR_EN 10
BL_ON/OFF 3
3V3SB USB_PWR_EN0
U401I SY S_EEPROM_WP USB_PWR_EN0 15
SY S_EEPROM_WP 4
LED_POWER_RED U3 WiFi_PWR_EN
LED_PWR_GREEN V2 OPCTRL0 B1 LVDS_PWR_EN BL_DIMMING WiFi_PWR_EN 15
V3 OPCTRL1 GPIO0 E5 BL_ON/OFF LED_POWER_RED BL_DIMMING 3
AMP_MUTE V1 OPCTRL2 GPIO1 G17 USB_PWR_EN0 LED_PWR_GREEN LED_POWER_RED 4,10
R499
KEY _On_board U4 OPCTRL3 GPIO2 H5 KEY _On_board LED_PWR_GREEN 4,10
10K +-1% 1/16W
OPCTRL4 GPIO3 H4 SY S_EEPROM_WP KEY _On_board 10
GPIO4 F17 USB_PWR_OCP0
T7 GPIO5 KEY _UP_DN_DCSW USB_PWR_OCP0 15
P8 ADIN0 KEY _MENU_L_R_SOURCE KEY _UP_DN_DCSW 10
U8 ADIN1 G6 USB_OC KEY _MENU_L_R_SOURCE 10
USB_PWR_OCP0 U6 ADIN2 OPWM2 G5 WiFi_PWR_EN USB_OC 15
KEY _UP_DN_DCSW T8 ADIN3 OPWM1 E6 BL_DIMMING AMP_MUTE
R481 R448 KEY _MENU_L_R_SOURCE U5 ADIN4 OPWM0 AMP_MUTE 6
10K +-1% 1/16W NC 10K +-1% 1/16W T6 ADIN5
USB_OC R8 ADIN6
ADIN7
MT5561LVNT
3 2014-07-07
GPIO 715G6836
19760_519.eps
2015-Aug-08 back to
div.table
10-4-13 USB/WIFI
B13 USB/ WiFi B13

U401F
H19 USB_DM_P0 3,4,5,6,7,8,9,10,11,12,13,14,16,17,18 GND
USB_DM0 H18 USB_DP_P0
USB_DP0 G19 USB_DM_P1
USB_DM1 F19 3,9,10,11,12 +5V_SW +5V_SW
USB_DP_P1
USB_DP1 3,4,5,6,8,9,10,11,13,16,17,18 DVDD3V3 DVDD3V3
R1114 2.5 = > NORMAL AVDD1V2
3,8,13 AVDD1V2
10K +-1% 1/16W
< 2.0 = >OC
W2 +5V_SW
RXVN W3 TP410
DVDD3V3
RXVP Y1 TP411 USB_OC
TXVN
TXVP
Y2 TP412
TP413
Control Interface
W4 REXT TH101
6
REXT_ETH R1024 R1032 USB_PWR_OCP0
PTCR USB_PWR_OCP0 14
t
Y4 AVDD12_ETH 1 2 4 USB_PWR_EN0
4 3 2 1
10K +-1% 1/16W
AVDD12_ETH R9 AVDD33_ETH R1027 NC 10K 1/16W 5% USB_DP_P0 3 USB_OC USB_PWR_EN0 14
AVDD33_ETH HI = > POWER ON U404 USB_OC 14
24K 1% LO = > POWER OFF USB_DM_P0 2 WiFi_PWR_EN
5 1 USB_PR 1 WiFi_PWR_EN 14
IN OUT
ZD118
ZD119
2
1
MT5561LVNT USB_PWR_EN0 4 GND 3 R1025 USB_PWR_OCP0 DEMOD_TSCLK
18 DEMOD_TSCLK
5
EN OC
C174
C175 NC/10P 50V
C176
C173 10UF 10V
NC 0R05 1/16W DEMOD_TSVAL
18 DEMOD_TSVAL
DEMOD_TSSYNC
18 DEMOD_TSSYNC
R1026 NC/G5250M1T1U HI = > NORMAL CN103 DEMOD_TSDATA0
18 DEMOD_TSDATA0
NC/10P 50V
100NF 16V
NC 4.7K 1/16W LO => OC USB CONN
2
NC/AZ5123-01H
AVDD1V2 DVDD3V3
AVDD12_ETH AVDD33_ETH
C170
C171 C172
1UF 10% 16V NC/100N 16V NC/100N 16V
U401H
B8
CI_D0 D13
A12 CI_D1 F9 DVDD3V3
C10 CI_MCLKO CI_D2 E17
D11 CI_MOVAL CI_D3 E19 R1115 NC 10K 1/16W 5% WiFi_PWR_EN
E11 CI_MOSTRT CI_D4 D20
E7 CI_MDO0 CI_D5 D18
E8 CI_MDO1 CI_D6 B20 WiFi Q706 +5V_SW
6
E16 CI_MDO2 CI_D7
E20 CI_MDO3 D9 NC AO3401A
D19 CI_MDO4 CI_A0 C9 4
C20 CI_MDO5 CI_A1 F10 3 R451 NC 5R6 1/16W 5% USB_DM_P1
C19 CI_MDO6 CI_A2 A10 CN403 2 R452 NC 5R6 1/16W 5% USB_DP_P1
CI_MDO7 CI_A3 D10 NC CONN 1
DEMOD_TSCLK D14 CI_A4 E10
DEMOD_TSVAL B13 CI_MCLKI CI_A5 B12
DEMOD_TSSYNC D16 CI_MIVAL CI_A6 D12
5
DEMOD_TSDATA0 A16 CI_MISTRT CI_A7 C16
C15 CI_MDI0 CI_A8 C17
C14 CI_MDI1 CI_A9 A19
C13 CI_MDI2 CI_A10 B18
A13 CI_MDI3 CI_A11 E9
E12 CI_MDI4 CI_A12 B16
F12 CI_MDI5 CI_A13 A15
E13 CI_MDI6 CI_A14
CI_MDI7 C18
F18 CI_OE# B15
CI_PWR_EN CI_WE# A18
CI_IORD# D17
CI_IOWR# C12
CI_RESET F11
CI_IREQ# C11
CI_WAIT# B10
CI_REG# B19
CI_CE1# F7
CI_CD2# E18
CI_CD1#
MT5561LVNT
3 2014-07-07
USB/ WiFi 715G6836
19760_520.eps
2015-Aug-08 back to
div.table
10-4-14 FACTORY DEBUG PORT
B14 FACTORY DEBUG PORT B14
+5VSB
3,4,5,6,7,8,9,10,11,12,13,14,15,17,18 GND
3,9,10,11,12,15 +5V_SW +5V_SW

3,7,9 +5VSB +5VSB
3,4,5,6,8,9,10,11,13,15,17,18 DVDD3V3 DVDD3V3
R406 HDMI_SCL2
10K +-1% 1/16W HDMI_SDA2 HDMI_SCL2 13
HDMI_SCL2/RX HDMI_SDA2 13
+5VSB
U414 HDMI_SDA2/TX HDMI_SCL2/RX 13
HDMI_SDA2/TX 13
6 4 HDMI_SCL2
/E 2Y 3
U0TX
R464 11 HDMI_SDA2 U0RX U0TX 4
10K +-1% 1/16W S1 9 1Y 3 U0RX 4
S1 ARC_on/of f
S0 10 2 U0RX ARC_SPDIF ARC_on/of f 10
S0 2Y 2 UART_SEL ARC_SPDIF 5
15 U0TX UART_SEL 13
UART_SEL R466 HDMI_SCL2/RX 3 1Y 2
Q404
2Z
60.4K 1% LMBT3904LT1G HDMI_SDA2/TX 13 5
1Z 2Y 1 HDMI
R467 14 pin14 S0 S1 CHANNEL
40.2K 1/16W 1% 8 1Y 1
GND
7 1 NC/ARC H H
D401 VEE 2Y 0 HDMI function
+5VSB 16 12
VCC 1Y 0 +12V L H Debug mode
BAS316 C408
74HC4052PW
100NF 16V
HDMI_SCL2/RX R493 HDMI_SCL2

NC 0R05 1/16W
HDMI_SDA2/TX R494 HDMI_SDA2
NC 0R05 1/16W
DVDD3V3
10mil
R468
10K +-1% 1/16W DVDD3V3
ARC_on/of f C443
U410 100NF 16V
1 5
ARC_SPDIF 2 OE Vcc C444
3 A 4 R470
UART_SEL
GND B
180R 1/10W 1%
74CBTLV1G125GW 1UF 25V
R471
82R 1/10W 1%
ARC on/off enable control

L :ON-state
H :OFF-state
3 2014-07-07
FACTORY DEBUG PORT 715G6836
19760_521.eps
2015-Aug-08 back to
div.table
10-4-15 VCCK & DVSS
B15 VCCK & DVSS B15
U401J VCC3IO
3,4,5,6,7,8,9,10,11,12,13,14,15,16,18 GND
M12 P9
M13 DVSS VCC3IO N10 3,4,5,6,8,9,10,11,13,15,16,18 DVDD3V3 DVDD3V3
M11 DVSS VCC3IO P10 3 VCCK VCCK
L12
M9
DVSS
DVSS
VCC3IO 3.3V IO Power
VCCK
R13 DVSS DVDD3V3 VCC3IO
H9 DVSS L6
H10 DVSS VCCK L5
H12 DVSS VCCK L4
A1 DVSS VCCK L3 C463 C446
J10 DVSS VCCK L2 C447 C448
J11 DVSS VCCK L1 1UF 10V
DVSS VCCK 10UF 6.3V 20% 10N 50V 10N 50V
J12 J9
K9 DVSS VCCK K5
K10 DVSS VCCK K6
K11 DVSS VCCK
DVSS
K12 K7
A8 DVSS VCCK K8
F6 DVSS VCCK L7
F20
G7
DVSS
DVSS
VCCK
VCCK
L8
M7
Core Power
G18 DVSS VCCK M8 VCCK
H13 DVSS VCCK
H11 DVSS
J13 DVSS
L9 DVSS M4 C452 C453
+ C449 C450 C451
L11 DVSS DVSS M3 C454
L13 DVSS DVSS N8 100UF 16V 1UF 10V 1UF 10V
DVSS DVSS 10UF 6.3V 20% 10UF 6.3V 20%
M1 M5 4.7UF 10% 10V
M2 DVSS DVSS R6
L10 DVSS DVSS M6
N13 DVSS DVSS
N11 DVSS R11 VCCK
N12 DVSS DVSS R12
N15 DVSS DVSS R14
T13 DVSS DVSS T5
N16 DVSS DVSS W19 C461 C456 C457 C458 C459 C460
P7 DVSS DVSS Y3
P11 DVSS DVSS 100NF 16V 100NF 16V 100NF 16V 100NF 16V
DVSS 10UF 6.3V 20% 10UF 6.3V 20%
P12
P14 DVSS H14
DVSS DVSS H16
G8 DVSS J7
V16 DVSS DVSS M10
U16 DVSS DVSS N7
T15 DVSS DVSS N9
DVSS DVSS
MT5561LVNT
3 2014-07-07
VCCK & DVSS 715G6836
19760_522.eps
2015-Aug-08 back to
div.table
10-4-16 DEMOD_Toshiba TC90537
B16 DEMOD_Toshiba TC90537 B16
XT_O
DVDD3V3 DVDD3V3 3,4,5,6,7,8,9,10,11,12,13,14,15,16,17 GND
R136 XT_I
1M 1/10W 5%
R111 3,4,5,6,8,9,10,11,13,15,16,17 DVDD3V3 DVDD3V3
R126
NC/ 10K+-5%1/16W R137 DEMOD_TSCLK
NC/ 10K+-5%1/16W 15 DEMOD_TSCLK
DEMOD_TSVAL
1.2K OHM 1/16W 1% 15 DEMOD_TSVAL
DEMOD_TSSYNC
15 DEMOD_TSSYNC
2
SLADRS0 SLADRS1 X101 DEMOD_TSDATA0
R135 1 3 15 DEMOD_TSDATA0
IFAGC_Toshiba_demo 10K 1/10W
R125 R134 16MHZ
4
C119 C138 C178 C179 TUNER_SCL
10K +-1% 1/16W 10K +-1% 1/16W 100NF 16V 100NF 16V SLADRS0 27PF 27PF 11 TUNER_SCL TUNER_SDA
11 TUNER_SDA IFAGC_Toshiba_demo
11 IFAGC_Toshiba_demo D_IFP
AGCCNTI
11 D_IFP D_IFN
11 D_IFN
OSCL1
SBYTE_ORR OSDA1 OSCL1 4,11
OSDA1 4,11
TUNER_SCL R139
TUNER_SDA
20K OHM 1/16W 1%
R138 DVDD3V3 NC 0R05 OHM

GPIO Interface
DEMOD_RST
XT_O TP101 C177 10 DEMOD_RST
XT_I 100NF 16V
U101
24
23
22
21
20
19
18
17
16
15
14
13
+1V2 TC90537FG
VSS
XO
XI
SBYTE
XCKO
SLADRS0
VDDS
TNSCL
RSEORF
TNSDA
AGCCNT1
AGCCNTR
FB105
120R
FB407 10R
2 1 RP101
C180 C181 25 12 SRCK_ORR 1 2 33 OHM +-5% 1/16W
FB106 PLLVDD SRCK 5 4
100NF 16V 10UF 6.3V 20% 26 11 6 3 DEMOD_TSSYNC 15
120R PBVAL_ORR
PLLVSS PBVAL 7 2 DEMOD_TSCLK 15
2 1 27 10 8 1 DEMOD_TSVAL 15
SRDT_ORR
VDDC SRDT DEMOD_TSDATA0 15
C182 28 9 TP102
100NF 16V CKI SLOCK
SLADRS1 29 8 TP103 C1074
SLADRS1 RLOCK NC 10PF 50V
30 7 TP104
FB107 TSMD RERR
120R C183 31 6 TP105
100NF 16V VSS SLPEN
2 1 32 5 TP106
VDDC GPIO2
2 1 33 4 TP107
FB1010 ADCVDD GPIO1
C184 C185 34 3
120R 10UF 6.3V 20% TP108
100NF 16V ADCVSS GPIO0
35 2 +1V2
VREFL VSS
2 1 36 1 2 1
FB1008 C186 VREFH VDDC FB1009
120R 100NF 16V C199 120R
STSFLG1
STSFLG0
SYRSTN
100NF 16V
AINN Q
AINP Q
AINN I
VPGM
AINP I
VDDS
SDA
VSS
SCL
37
38
39
40
41
42
43
44
45
46
47
48
DVDD3V3 DVDD3V3
U103 +1V2
D_IFP
D_IFN 1 5
IN OUT
R154 2.2K 1%
R143 C188
DVDD3V3 100NF 16V 2 C195
100R 1/16W 5%
R144 C194 GND
100R 1/16W 5% R145
C187 C189 DVDD3V3 1UF 10V 3 4 10UF 6.3V 20%
R140 100R 1/16W 5% SHDN SET
100NF 16V 100NF 16V
0R05 OHM
G9141T11U
R141
R146 R147 R148
10K +-1% 1/16W
TP110 TP109 4.7K 1/16W 4.7K 1/16W 10K +-1% 1/16W
DEMOD_RST OSDA1
OSCL1
R142
C193
10N 50V NC 10K 1/16W 5%
3 2014-07-07
DEMOD_Toshiba TC90537 715G6836
19760_523.eps
2015-Aug-08 back to
div.table
10-4-17 SSB layout top
LAYOUT TOP 715G6836
19760_524.eps
2015-Aug-08 back to
div.table
10-4-18 SSB layout bottom
LAYOUT BOTTOM 715G6836
19760_525.eps
2015-Aug-08 back to
div.table
10.5 J 715G6167 IR/LED Panel

10-5-1 IR/LED Panel
IR/LED panel
J J
3V3SB
R001
470R 1/16W 5%
3V3SB
1
LED001
LED
R003 R004
NC/2K7 1/16W 5% 100R 1/16W 5%
2
R002
1K 1/16W 5%
C001
Q001
BC847C
U001
CN001 1UF16V 1
6
2 GND
3 Vs
----><----|
1 4 OUT
2 LED_R 3V3SB GND
3 RC6
4 TSOP75436WTT
C002 ----><----|
5 Key1 NC/1N 50V
2
----><----|
2
C003
VPORT0603100KV05
VPORT0603100KV05
CONN
ZD003
100N 16V
ZD002
7
TACT SW FWRD H1.5MM
SW001
1
1
POWER
----><----|
NC/100N 50V
0R051/8W
R005
C004
C 2013-04-29
IR/LED panel
715G6167
19641_500.eps
2015-Aug-08 back to
div.table
10-5-2 IR/LED board layout
Layout IR/LED panel (top side)
Layout IR/LED panel (bottom side)
C 2013-04-29
IR/LED panel
715G6167
layout top/bottom
19641_501.eps
2015-Aug-08 back to
div.table
10.6 E 715G6316 Keyboard control panel

10-6-1 Key
Key
E E
Direction switch Key functionResistance Voltage
Center 2-5 short Menu 0R 0V
Right 1-5 short CH+ 1K2 0.5V
Left 4-5 short CH- 2K2 0.81V
Down 3-5 short VOL- 6K8 1.65V

CN01
3
Up 6-5 short VOL+ 15K 2.27V

1 KEY1
2 ----><----|
No function 3.3V
C06
CONN 7
4
100N 50V SW01

1 F5 F4 6
2 F1 5
3 F3 F2 4
SW 6P
8
Joystick circuit diagram
pin1 pin2 pin3 pin4 pin5 pin6
F1
F2
F3
F4
F5
Right Center Down Left Up
----><----|
----><----|
----><----|
----><----|
----><----|
6K8 1/10W 1%
NC/100N 50V
NC/100N 50V
NC/100N 50V
NC/100N 50V
NC/100N 50V
1K2 1/10W 1%
2K2 1/10W 1%
15K 1/10W 1%
0R05 1/10W
R01
R02
R03
R04
R05
C01
C02
C03
C04
C05
1 2013-09-17
Keyboard control panel

715G6316
19610_545.eps
2015-Aug-08 back to
div.table
10-6-2 Key board layout
Layout Keyboard control panel (top side)
CN01
R05
C05
C06
R1 SW4
SW2
SW3
C04
R01
SW01
SW5
R04
C01
R02
SW6
C02 SW7
C03
R03
R2
Layout Keyboard control panel (bottom side)
1 2013-09-17
Keyboard control panel

715G6316
layout top/bottom
19610_546.eps
2015-Aug-08 back to
div.table
Styling Sheets TPM15.5L LA 11. EN 74
11. Styling Sheets

11.1 4900/5000 series 32"
4900/5000 series 32"
1053
1184
0095
0040
1054
0030
1056 1057
1184
0050
1050 Pos No. Description Remarks

0030 Bezel
0040 Rear cover
0050 Stand Assembly
0095 V0 SHEET
1050 Display panel
1053 Panel SSB
1054 Power Supply Unit
1056 IR/LED panel
1057 Keyboard control panel
1176 Remote control Not displayed
1184 Speakers
FOR ELECTRICAL PARTS/ASSEMBLIES SEE WIRING DIAGRAM CHAPTER 9
19761_800.eps
2015-Aug-08 back to
div.table
11.2 5000 series 40" & 43"
5000 series 40" & 43"
1053
0040
1184
1057
1054
0030
1184 0095
0050
Pos No. Description Remarks

1050 0030 Bezel
0040 Rear cover
0050 Stand Assembly
0095 V0 SHEET
1050 Display panel
1053 Panel SSB
1056 1054 Power Supply Unit
1056 IR/LED panel
1184 Speakers

19760_801.eps
2015-Aug-08 back to
div.table
11.3 5000 series 48"
5000 series 48"
1053
1184
0030
1054
0095
0040
1050 1184
1057
1056
0050
Pos No. Description Remarks

0030 Bezel
0040 Rear cover
0050 Stand Assembly
0095 V0 SHEET
1050 Display panel
1053 Panel SSB
1054 Power Supply Unit
1056 IR/LED panel
1184 Speakers

19760_802.eps
2015-Aug-08 back to
div.table

Philips+32PHG4900,+32PHG5000 TPM15.5L anotacoes

Uploaded by

Copyright:

Available Formats

Philips+32PHG4900,+32PHG5000 TPM15.5L anotacoes

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Philips+32PHG4900,+32PHG5000 TPM15.5L anotacoes

Uploaded by

Copyright:

Available Formats

Colour Television Chassis

TROCA PLACA 48PFG500 POR 43PFG500 IMAGEM

Contents Page Contents Page

2. Technical Specs, Diversity, and Connections

Table 2-1 Described Model Numbers and Diversity

E (Key board/Leading Edge)

Rear Cover Removal

2.2 Directions for Use

Rear Connectors Side Connectors

Figure 2-1 Connection overview

2.4 Chassis Overview

3. Precautions, Notes, and Abbreviation List

DNR Digital Noise Reduction: noise The SDI signal is self-synchronizing,

PDP Plasma Display Panel SWAN Spatial temporal Weighted Averaging

4.1 Cable Dressing

LOUDSPEAKER IR/LED BOARD

Figure 4-1 Cable dressing (32" 4900/5000 series)

MAIN POWER SUPPLY

Figure 4-2 Cable dressing (40" & 43" 5000 series)

MAIN POWER SUPPLY

Figure 4-3 Cable dressing (48" 5000 series)

4.2 Service Positions 4.3 Assembly/Panel Removal

Figure 4-4 Stand removal

4.3.2 Rear Cover

Refer to Figure 4-4 and Figure 4-5 for details.

Figure 4-5 Rear cover removal

4.3.3 Keyboard Control Unit

Refer to Figure 4-6 for details.

Figure 4-6 Keyboard Control unit removal

4.3.4 Small Signal Board (SSB)

Refer to Figure 4-7 for details.

Figure 4-7 SSB removal

4.3.5 Power Supply Unit (PSU)

Caution: it is mandatory to remount all different screws at their

1. Gently release the tapes that secure the speaker cables.

4.3.7 IR/LED Board

1. Remove the stand bracket as described earlier.

4.3.8 LCD Panel

1. Remove the SSB as described earlier.

4.4 Set Re-assembly

5. Service Modes, Error Codes, and Fault Finding

Table 5-1 SAM mode overview

Main Menu Sub-menu 1 Sub-menu 2 Description

How to Navigate Specifications

How to Exit SAM

5.2.3 Contents of the Factory mode:

Table 5-2 Factory mode overview

How to Navigate How to Exit CSM

5.3 Stepwise Start-up

Standby Soft Mode

Switch Off (Mains

Figure 5-1 Stepwise Start-up

5.4 Service Tools 5.5 Software Upgrading

5.4.1 ComPair 5.5.1 Description

Optional Power Link/ Mode

1. Open the internet page http://www.philips.com/support.

• FUS_clustername_version.zip: Contains the file

5.5.7 How to Copy NVM Data to/from USB

Service Modes Description

5.6 Error Codes