f105c38097848cfb6b86f57842206854Zytel 70G30HSLR BK099 - MDS - EN

PRODUCT INFORMATION
DuPont™ Zytel® 70G30HSLR BK099

NYLON RESIN
Product Information
Common features of Zytel® nylon resin include mechanical and physical properties such as high mechanical strength, excellent balance of stiffness and toughness, good high temperature
performance, good electrical and flammability properties, good abrasion and chemical resistance. In addition, Zytel® nylon resins are available in different modified and reinforced grades to
create a wide range of products with tailored properties for specific processes and end-uses. Zytel® nylon resin, including most flame retardant grades, offer the ability to be coloured.
The good melt stability of Zytel® nylon resin normally enables the recycling of properly handled production waste. If recycling is not possible, DuPont recommends, as the preferred option,
incineration with energy recovery (-31kJ/g of base polymer) in appropriately equipped installations. For disposal, local regulations have to be observed.
Zytel® nylon resin typically is used in demanding applications in the automotive, furniture, domestic appliances, sporting goods and construction industry.
Zytel® 70G30HSLR BK099 is a 30% glass fibre reinforced, heat stabilised, hydrolysis resistant polyamide 66 resin for injection molding.
General information Value Unit Test Standard

Resin Identification PA66-GF30 - ISO 1043
Part Marking Code PA66-GF30 - ISO 11469
Rheological properties dry / cond Unit Test Standard
Moulding shrinkage, parallel 0.3 / - % ISO 294-4, 2577
Moulding shrinkage, normal 1.0 / - % ISO 294-4, 2577
Mechanical properties dry / cond Unit Test Standard
Tensile Modulus 10000 / 7000 MPa ISO 527-1/-2
Stress at break 200 / 130 MPa ISO 527-1/-2
Strain at break 3/5 % ISO 527-1/-2
Flexural Modulus 9000 / 6300 MPa ISO 178 DS
Flexural Strength 280 / 200 MPa ISO 178 DS
Poisson's ratio 0.34 / 0.35 - ISO 527-1/-2
Charpy impact strength ISO 179/1eU
23°C 80 / 90 kJ/m²
-30°C 70 / 70 kJ/m² DS
-40°C 65 / - kJ/m²
Charpy notched impact strength ISO 179/1eA
23°C 12 / 14 kJ/m²
-30°C 9 / 9 kJ/m² DS
-40°C 9 / - kJ/m²
Izod notched impact strength, -40°C 10 / - kJ/m² ISO 180/1A
Ball indentation hardness, H 961/30 270 / 185 MPa ISO 2039-1
DS: Derived from similar grade
Thermal properties dry / cond Unit Test Standard
Melting temperature, 10°C/min 262 / * °C ISO 11357-1/-3
Glass transition temperature, 10°C/min 80 / 20 °C ISO 11357-1/-2
Temp. of deflection under load ISO 75-1/-2
1.8 MPa 253 / * °C
0.45 MPa 261 / * °C
Coeff. of linear therm. expansion, parallel 22 / * E-6/K ISO 11359-1/-2
Coeff. of linear therm. expansion ISO 11359-1/-2
normal 81 / * E-6/K
Normal, -40-23°C 72 / * E-6/K
Normal, 55-160°C 130 / * E-6/K
Parallel, -40-23°C 29 / * E-6/K
Parallel, 55-160°C 16 / * E-6/K
RTI, electrical UL 746B
0.75mm 140 / * °C
1.5mm 140 / * °C
3mm 140 °C
Revised: 2018-03-09 Page: 1 of 17

To find out more, visit DuPont Performance Polymers or contact nearest DuPont location.
North America Asia Pacific Europe/Middle East/Africa
Tel: +1 302 999-4592 Tel: +81 3 5521 8600 Tel: +41 22 717 51 11
Toll-Free (USA): 800 441-0575
Copyright 2017 DuPont. The DuPont Oval Logo is a trademark or registered trademark of E.I. du Pont de Nemours and
Company or its affiliates. All rights reserved.
NYLON RESIN
RTI, impact UL 746B
0.75mm 125 °C
1.5mm 125 / * °C
3mm 125 °C
RTI, strength UL 746B
0.75mm 140 °C
1.5mm 140 / * °C
3mm 140 °C
Flammability dry / cond Unit Test Standard
Burning Behav. at 1.5mm nom. thickn. HB / * class IEC 60695-11-10
Thickness tested 1.5 / * mm IEC 60695-11-10
UL recognition UL / * - UL 94
Burning Behav. at thickness h HB / * class IEC 60695-11-10
Thickness tested 0.75 / * mm IEC 60695-11-10
UL recognition UL / * - UL 94
Oxygen index 24 / * % ISO 4589-1/-2
FMVSS Class SE/B - ISO 3795 (FMVSS 302)
Burning rate, Thickness 1 mm 24 mm/min ISO 3795 (FMVSS 302)
Electrical properties dry / cond Unit Test Standard
Volume resistivity >1E13 / 1E9 Ohm*m IEC 62631-3-1 DS
Comparative tracking index
Comparative tracking index 400 / - - IEC 60112
CTI, 23°C 1/- PLC UL 746A
DS: Derived from similar grade
Other properties dry / cond Unit Test Standard
Humidity absorption, 2mm 1.9 / * % Sim. to ISO 62
Water absorption, 2mm 6/* % Sim. to ISO 62
Density 1370 / - kg/m³ ISO 1183
VDA Properties Value Unit Test Standard
Odour 5 class VDA 270
Injection dry / cond Unit Test Standard
Drying Recommended yes - -
Drying Temperature ≥80 °C -
Drying Time, Dehumidified Dryer 2-4 h -
Processing Moisture Content ≤0.2 % -
Melt Temperature Optimum 295 °C -
Min. melt temperature 285 °C -
Max. melt temperature 305 °C -
Max. screw tangential speed 0.2 / * m/s -
Mold Temperature Optimum 100 °C -
Min. mould temperature 70 °C -
Max. mould temperature 120 °C -
Hold pressure range 50 - 100 MPa -
Hold pressure time 3 s/mm -
Ejection temperature 210 °C -
Characteristics
Processing Injection Moulding
Delivery form Pellets
Additives Lubricants Release agent
Heat stabilised or stable
Special characteristics
to heat
North America Asia Pacific Near East/Africa
Regional Availability
Europe South and Central America Global
Revised: 2018-03-09 Page: 2 of 17

Tel: +1 302 999-4592 Tel: +81 3 5521 8600 Tel: +41 22 717 51 11
Toll-Free (USA): 800 441-0575
NYLON RESIN
Diagrams
Viscosity-shear rate
1E3 285 °C
295 °C
305 °C
Viscosity in Pa s
1E2
1E1
1E2 1E3 1E4
Shear rate in 1/s
Shearstress-shear rate
1E6 285 °C
295 °C
305 °C
Shearstress in Pa
1E5
1E4
1E2 1E3 1E4
Shear rate in 1/s
Revised: 2018-03-09 Page: 3 of 17

Tel: +1 302 999-4592 Tel: +81 3 5521 8600 Tel: +41 22 717 51 11
Toll-Free (USA): 800 441-0575
NYLON RESIN
Dynamic Shear modulus-temperature (dry)
1E4
Shear modulus in MPa
1E3
1E2
-50 0 50 100 150 200 250
Temperature in °C
Dynamic Shear modulus-temperature (cond.)
1E4
Shear modulus in MPa
1E3
1E2
-50 0 50 100 150 200 250
Temperature in °C
Revised: 2018-03-09 Page: 4 of 17

Tel: +1 302 999-4592 Tel: +81 3 5521 8600 Tel: +41 22 717 51 11
Toll-Free (USA): 800 441-0575
NYLON RESIN
Dynamic Tensile modulus-temperature (dry)
1E4
0.08
1E3
1E3
0.06
Dyn. Tensile modulus in MPa
1E2
E" in MPa
tan d
1E2
0.04
1E1
1E1
0.02
1E0
1E0
0
1E-1-50 0 50 100 150 200 250
Temperature in °C
Revised: 2018-03-09 Page: 5 of 17

Tel: +1 302 999-4592 Tel: +81 3 5521 8600 Tel: +41 22 717 51 11
Toll-Free (USA): 800 441-0575
NYLON RESIN
Stress-strain (dry)
250 -40 °C
B -20 °C
0 °C
23 °C
B 40 °C
B 60 °C
200 80 °C
B 100 °C
120 °C
150 °C
160 °C
B
B - Break
150
Stress in MPa
B
B
100
B
B
B
50
0
0 1 2 3 4 5 6 7
Strain in %
Revised: 2018-03-09 Page: 6 of 17

Tel: +1 302 999-4592 Tel: +81 3 5521 8600 Tel: +41 22 717 51 11
Toll-Free (USA): 800 441-0575
NYLON RESIN
Stress-strain (cond.)
250 -40 °C
-20 °C
0 °C
B 23 °C
B 40 °C
60 °C
200 80 °C
120 °C
140 °C
B
B - Break
150
Stress in MPa
B
100 B
B
B
B
50
0
0 1 2 3 4 5 6 7
Strain in %
Revised: 2018-03-09 Page: 7 of 17

Tel: +1 302 999-4592 Tel: +81 3 5521 8600 Tel: +41 22 717 51 11
Toll-Free (USA): 800 441-0575
NYLON RESIN
Secant modulus-strain (dry)
12000 -40 °C
-20 °C
0 °C
23 °C
40 °C
10000 60 °C
80 °C
100 °C
120 °C
150 °C
160 °C
8000
Secant modulus in MPa
BB B - Break
B
6000
B
B
4000
B
2000
B B
B BB
0
0 1 2 3 4 5 6 7
Strain in %
Revised: 2018-03-09 Page: 8 of 17

Tel: +1 302 999-4592 Tel: +81 3 5521 8600 Tel: +41 22 717 51 11
Toll-Free (USA): 800 441-0575
NYLON RESIN
Secant modulus-strain (cond.)
12000 -40 °C
-20 °C
0 °C
23 °C
40 °C
10000 60 °C
80 °C
120 °C
140 °C
8000 B - Break
Secant modulus in MPa
6000
B
4000
B
B
2000
BB B
BB
0
0 1 2 3 4 5 6 7
Strain in %
Revised: 2018-03-09 Page: 9 of 17

Tel: +1 302 999-4592 Tel: +81 3 5521 8600 Tel: +41 22 717 51 11
Toll-Free (USA): 800 441-0575
NYLON RESIN
Stress-strain (isochronous) 140°C(dry)
70 1h
10 h
100 h
1000 h
60
50
Stress in MPa
40
30
20
10
0
0 0.5 1 1.5 2 2.5 3 3.5
Strain in %
Revised: 2018-03-09 Page: 10 of 17

Tel: +1 302 999-4592 Tel: +81 3 5521 8600 Tel: +41 22 717 51 11
Toll-Free (USA): 800 441-0575
NYLON RESIN
Creep modulus-time 140°C(dry)
3500 10 MPa
20 MPa
30 MPa
40 MPa
50 MPa
60 MPa
3000
Creep modulus in MPa
2500
2000
1500
1E0 1E1 1E2 1E3
Time in h
Revised: 2018-03-09 Page: 11 of 17

Tel: +1 302 999-4592 Tel: +81 3 5521 8600 Tel: +41 22 717 51 11
Toll-Free (USA): 800 441-0575
NYLON RESIN
Stress-strain (isochronous) 180°C(dry)
60 1 h
10 h
100 h
1000 h
50 B B - Break
40
Stress in MPa
30
20
10
0
0 0.5 1 1.5 2 2.5 3 3.5
Strain in %
Revised: 2018-03-09 Page: 12 of 17

Tel: +1 302 999-4592 Tel: +81 3 5521 8600 Tel: +41 22 717 51 11
Toll-Free (USA): 800 441-0575
NYLON RESIN
Creep modulus-time 180°C(dry)
3000 5 MPa
10 MPa
15 MPa
20 MPa
2800 25 MPa
Creep modulus in MPa
2600
2400
2200
2000
1800
1E0 1E1 1E2 1E3
Time in h
Specific volume-temperature (pvT)
0.84 0.1 MPa

40 MPa
120 MPa
0.82 200 MPa
Spec. volume in E-3 m³/kg
0.8
0.78
0.76
0.74
0.72
0.7
0 50 100 150 200 250 300
Temperature in °C
Revised: 2018-03-09 Page: 13 of 17

Tel: +1 302 999-4592 Tel: +81 3 5521 8600 Tel: +41 22 717 51 11
Toll-Free (USA): 800 441-0575
NYLON RESIN
Tensile Fatigue, 10Hz, R=0.1 0mm(dry)
70 80 °C
120 °C
65
Stress in MPa
60
55
1E5 1E6 1E7
Cycles
Revised: 2018-03-09 Page: 14 of 17

Tel: +1 302 999-4592 Tel: +81 3 5521 8600 Tel: +41 22 717 51 11
Toll-Free (USA): 800 441-0575
NYLON RESIN
Chemical Media Resistance
Acids
Acetic Acid (5% by mass) (23°C)
Citric Acid solution (10% by mass) (23°C)
Lactic Acid (10% by mass) (23°C)
Hydrochloric Acid (36% by mass) (23°C)
Nitric Acid (40% by mass) (23°C)
Sulfuric Acid (38% by mass) (23°C)
Sulfuric Acid (5% by mass) (23°C)
Chromic Acid solution (40% by mass) (23°C)
Bases
Sodium Hydroxide solution (35% by mass) (23°C)
Sodium Hydroxide solution (1% by mass) (23°C)
Ammonium Hydroxide solution (10% by mass) (23°C)
Alcohols
Isopropyl alcohol (23°C)
Methanol (23°C)
Ethanol (23°C)
Hydrocarbons
n-Hexane (23°C)
Toluene (23°C)
iso-Octane (23°C)
Ketones
Acetone (23°C)
Ethers
Diethyl ether (23°C)
Mineral oils
SAE 10W40 multigrade motor oil (23°C)
SAE 10W40 multigrade motor oil (130°C)
SAE 80/90 hypoid-gear oil (130°C)
Insulating Oil (23°C)
Motor oil OS206 304 Ref.Eng.Oil, ISP (135°C)
Automatic hypoid-gear oil Shell Donax TX (135°C)
Hydraulic oil Pentosin CHF 202 (125°C)
Standard Fuels
ISO 1817 Liquid 1 - E5 (60°C)
ISO 1817 Liquid 2 - M15E4 (60°C)
ISO 1817 Liquid 3 - M3E7 (60°C)
Revised: 2018-03-09 Page: 15 of 17

Tel: +1 302 999-4592 Tel: +81 3 5521 8600 Tel: +41 22 717 51 11
Toll-Free (USA): 800 441-0575
NYLON RESIN
ISO 1817 Liquid 4 - M15 (60°C)
Standard fuel without alcohol (pref. ISO 1817 Liquid C) (23°C)
Standard fuel with alcohol (pref. ISO 1817 Liquid 4) (23°C)
Diesel fuel (pref. ISO 1817 Liquid F) (23°C)
Diesel fuel (pref. ISO 1817 Liquid F) (90°C)
Diesel fuel (pref. ISO 1817 Liquid F) (>90°C)
Salt solutions
Sodium Chloride solution (10% by mass) (23°C)
Sodium Hypochlorite solution (10% by mass) (23°C)
Sodium Carbonate solution (20% by mass) (23°C)
Sodium Carbonate solution (2% by mass) (23°C)
Zinc Chloride solution (50% by mass) (23°C)
Other
Ethyl Acetate (23°C)
Hydrogen peroxide (23°C)
DOT No. 4 Brake fluid (130°C)
DOT No. 4 Brake fluid (120°C)
Ethylene Glycol (50% by mass) in water (108°C)
1% nonylphenoxy-polyethyleneoxy ethanol in water (23°C)
50% Oleic acid + 50% Olive Oil (23°C)
Water (23°C)
Water (90°C)
Phenol solution (5% by mass) (23°C)
Coolant Glysantin G48, 1:1 in water (125°C)
Symbols used:
possibly resistant
Defined as: Supplier has sufficient indication that contact with chemical can be potentially accepted under the intended use conditions and
expected service life. Criteria for assessment have to be indicated (e.g. surface aspect, volume change, property change).
not recommended - see explanation

Defined as: Not recommended for general use. However, short-term exposure under certain restricted conditions could be acceptable (e.g. fast
cleaning with thorough rinsing, spills, wiping, vapor exposure).
Contact DuPont for Material Safety Data Sheet, general guides and/or additional information about ventilation, handling, purging, drying, etc.
ISO Mechanical properties measured at 4mm (Hytrel® measured at 2 mm), IEC Electrical properties measured at 2mm, all ASTM properties
measured at 3.2mm, and test temperatures are 23°C unless otherwise stated.
The information set forth herein is furnished free of charge and is based on technical data that DuPont believes to be reliable and falls within
the normal range of properties. It is intended for use by persons having technical skill, at their own discretion and risk. This data should not be
used to establish specification limits nor used alone as the basis of design. Handling precaution information is given with the understanding that
those using it will satisfy themselves that their particular conditions of use present no health or safety hazards. Since conditions of product use
and disposal are outside our control, we make no warranties, express or implied, and assume no liability in connection with any use of this
information. As with any product, evaluation under end-use conditions prior to specification is essential. Nothing herein is to be taken as a
Revised: 2018-03-09 Page: 16 of 17

Tel: +1 302 999-4592 Tel: +81 3 5521 8600 Tel: +41 22 717 51 11
Toll-Free (USA): 800 441-0575
NYLON RESIN
license to operate or a recommendation to infringe on patents. Caution: Do not use in medical applications involving permanent implantation in
the human body. For other medical applications, discuss with your DuPont customer representative and read Medical Caution H-50103-5.
Copyright © 2017 DuPont or its affiliates. All Rights Reserved. The DuPont Oval Logo, DuPont™, The miracles of science™ and all products
denoted with ® or ™ are registered trademarks or trademarks of E.I. du Pont de Nemours and Company or its affiliates.
Revised: 2018-03-09 Page: 17 of 17

Tel: +1 302 999-4592 Tel: +81 3 5521 8600 Tel: +41 22 717 51 11
Toll-Free (USA): 800 441-0575

f105c38097848cfb6b86f57842206854Zytel 70G30HSLR BK099 - MDS - EN

Uploaded by

Copyright:

Available Formats

f105c38097848cfb6b86f57842206854Zytel 70G30HSLR BK099 - MDS - EN

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

f105c38097848cfb6b86f57842206854Zytel 70G30HSLR BK099 - MDS - EN

Uploaded by

Copyright:

Available Formats

PRODUCT INFORMATION

DuPont™ Zytel® 70G30HSLR BK099

General information Value Unit Test Standard

Revised: 2018-03-09 Page: 1 of 17

Revised: 2018-03-09 Page: 2 of 17

Shear rate in 1/s

Shear rate in 1/s

Revised: 2018-03-09 Page: 3 of 17

Dynamic Shear modulus-temperature (dry)

Dynamic Shear modulus-temperature (cond.)

Revised: 2018-03-09 Page: 4 of 17

Dynamic Tensile modulus-temperature (dry)

Revised: 2018-03-09 Page: 5 of 17

Revised: 2018-03-09 Page: 6 of 17

Revised: 2018-03-09 Page: 7 of 17

Secant modulus-strain (dry)

Revised: 2018-03-09 Page: 8 of 17

Secant modulus-strain (cond.)

Revised: 2018-03-09 Page: 9 of 17

Stress-strain (isochronous) 140°C(dry)

Revised: 2018-03-09 Page: 10 of 17

Creep modulus-time 140°C(dry)

Revised: 2018-03-09 Page: 11 of 17

Stress-strain (isochronous) 180°C(dry)

Revised: 2018-03-09 Page: 12 of 17

Creep modulus-time 180°C(dry)

Specific volume-temperature (pvT)

0.84 0.1 MPa

Revised: 2018-03-09 Page: 13 of 17

Tensile Fatigue, 10Hz, R=0.1 0mm(dry)

Revised: 2018-03-09 Page: 14 of 17

Chemical Media Resistance

Revised: 2018-03-09 Page: 15 of 17

not recommended - see explanation

Revised: 2018-03-09 Page: 16 of 17

Revised: 2018-03-09 Page: 17 of 17

You might also like