USKUDAR UNIVERSITY

Faculty of Engineering and Natural

Sciences
Electrical-Electronics Engineering
Department

200206934 ABDEL SHWAIKI

RAHMAN
200206033 MERT KARA

220206801 ELIZ AKDER

TURAN
200206904 YASIN BAKILAH

Research Assistant
Enis KRANDA
nazmiye.kopacak@uskudar.edu.tr
enis.kranda@uskudar.edu.tr

Date of Submission: Weekday, 10 31, 2022

Fall, 2022
Theoretical part:

Oscilloscope: An instrument that is used to graphically display and analyze the waveform
of electrical signals and show how those signals change over time.

Figure 1: Oscilloscope

Function (signal) generator (aka FG): A test instrument used to generate different
types of electrical signals over a wide range of frequencies.

Figure 2: Function (signal) generator

Average Value, Peak Value, and Root Mean Square Value:

Discrete-time signal

Continuous-time signal
2. EXPERIMENTAL

Procedure:

Part 1: Measuring values using an Oscilloscope and Multimeter

Figure 5: Measurement devices

1- Connect the function generator to the oscilloscope as shown in Figure 3 above.

2- Generate a signal using the FG with the following parameters

a. Sinusoidal waveform
b. Frequency = 1 kHz
c. 𝑉𝑝 = 2.5 V
d. Offset = 1

3- Show the signal on the Oscilloscope and plot it on the following chart

Table 1: Oscilloscope signal for sinusoidal

wave
4- Using the Oscilloscope find the defined voltages below:
Table 2: Measured Data

𝑽𝒑 𝑽𝑷−𝑷 𝑽𝒓𝒎𝒔

2 4 2.43

5- Using the multimeter find 𝑉𝑟𝑚𝑠 and compare it with the 𝑉𝑟𝑚𝑠 from part 4. Why are
they not equal?
…… 𝑉𝑟𝑚𝑠 = 2 . 5 6 t h e y a r e n o t e q u a l b e c a u s e w e h a v e s o m e d i f f e r e n t i n t h e a t r i c a l a n d
e x p e r i m e n t a l ……………………………………

6- Generate a signal using the FG with the following parameters

a. Square waveform
b. Frequency = 10 kHz
c. 𝑉𝑝= 5 V
d. Offset = 2
e. Duty = 30%
Table 3: Oscilloscope signal for square
wave
Part 2: RC circuit

Phasor diagram of the resistance, capacitance, and inductance.

a) The current and voltage applied to a resistor are in phase.

b) The current passing through an inductor lags the voltage by 90o.
c) The current passing through a capacitor leads the voltage by 90o.

Figure 6: Phasor diagram

Phasor diagram of the R circuit

Figure 7: Phasor diagram of R circuit

1- Build the R circuit shown in Figure 8 above.

2- Connect the oscilloscope to display 𝑉𝑖𝑛 and 𝑉𝑅2.

3- Apply the math function in the oscilloscope to display 𝑉𝑅1 = 𝑉𝑖𝑛 − 𝑉𝑅2

4- Fill in the table below, (Osci means using an Oscilloscope)

 Table 4: Data for R circuit

R1 R2 VR1(P-P) VR2(P-P) Vin(P-P) ϴ 𝑽𝒊𝒏 = 𝑽𝑹𝟏 + 𝑽𝑹𝟐

k𝛀 k𝛀 (Osci) (Osci) (Osci) (Osci (calculatio
) n)
2 2 2 4 0 4
2

5- Is Vin (calculation) = Vin (Oscilloscope), why?

…………yes it’s almost the same because we are dealing with the same components we have
some differences in theatrical and experimental ……
Phasor diagram of the RC circuit

Figure 9: Phasor diagram of RC circuit

1- Build the RC circuit in the Figure 10 above.

2- Connect the oscilloscope to display 𝑉𝑖𝑛 and 𝑉𝐶.

3- Apply the math function in the oscilloscope to display VR=Vin-Vc.

4- Fill in the table

bellow Table 5: Data for R circuit
EEE201-Experiment-4 RC Circuit

Prepared by Dr. Hamza Abunima

Redesigned by Res. Asst. Nazmiye Kopacak, Res. Asst. Enis Kranda

Group Number: 1 Team Number: 2 Date: 19/12/2022

Φ
R C VR (P-P) Vc(P-P) Vin(P-P) 𝑽𝒊𝒏 = √𝑽𝑹𝟐 + 𝑽𝑪𝟐 ϴ = tan -1 𝑽𝒄
ϴ(Osci)
k𝛀 𝝁F (Osci) (Osci) (Osci) (Osci (calculation)
𝑽𝑹
)
2.28 3.33 4 57 -90 4 57
2 1

5- Is 𝑉𝑖𝑛 (calculation) = 𝑉𝑖𝑛 (Oscilloscope), why?

…………yes it’s almost the same because we are dealing with the same components we
have some differences in theatrical and experimental ……

8
 EEE201-Experiment-4 RC Circuit

Prepared by Dr. Hamza Abunima

Redesigned by Res. Asst. Nazmiye Kopacak, Res. Asst. Enis Kranda

Group Number: 1 Team Number: 2 Date: 19/12/2022

4. REFERENCES

In this part, you should add the reference list to provide full information about your report.
Reference list should be arranged in alphabetical order.

Abunima, H., Teh, J., & Jabir, H. J. (2019). A new solar radiation model for a power
system reliability study. IEEE Access, 7, 64758-64766.

Apaydin, G., Seker, S., & Ari, N. (2007). Weighted extended b-splines for one-
dimensional electromagnetic problems. Applied mathematics and computation, 190(2),
1125-1135.

Çerezci, O., & Şeker, S. (2010, December). Determining of electromagnetic pollution in

Bursa Nilufer district and recommending a sample model to decrease exposure levels. In
National Conference on Electrical, Electronics and Computer Engineering (pp. 1-5). IEEE.

Cini, U. (2014, December). A low-offset high CMRR current-mode instrumentation

amplifier using differential difference current conveyor. In 2014 21st IEEE International
Conference on Electronics, Circuits and Systems (ICECS) (pp. 64-67). IEEE.

Clark II, W. W., & Rifkin, J. (2006). A green hydrogen economy. Energy Policy, 34(17),
2630-2639.

Kopacak, N., & Aydın, M. (2015, November). Sample criteria for integration of solar plant
systems to electrical distribution network. In 2015 9th International Conference on
Electrical and Electronics Engineering (ELECO) (pp. 394-397). IEEE.

Seker, S., & Kunter, F. C. (2011). Multi-components mobile propagation model of park
environment. IEEE transactions on magnetics, 47(5), 1494-1497

9
EEE201-Experiment-4 RC Circuit

Prepared by Dr. Hamza Abunima

Redesigned by Res. Asst. Nazmiye Kopacak, Res. Asst. Enis Kranda

Group Number: 1 Team Number: 2 Date: 19/12/2022

10