d60

GE
Digital Energy
D60 Line Distance Protection

System
UR Series Instruction Manual
D60 Revision: 7.1x
Manual P/N: 1601-0089-Z2 (GEK-119515A)
E83849
GE Digital Energy
LISTED
650 Markland Street
IND.CONT. EQ.
Markham, Ontario 52TL
GE Multilin's Quality Management
Canada L6C 0M1 System is registered to ISO
9001:2008
Tel: +1 905 927 7070 Fax: +1 905 927 5098 QMI # 005094
UL # A3775
Internet: http://www.GEDigitalEnergy.com
*1601-0089-Z2*
Copyright © 2013 GE Multilin Inc. All rights reserved.
D60 Line Distance Protection System UR Series Instruction Manual revision 7.1x.
FlexLogic, FlexElement, FlexCurve, FlexAnalog, FlexInteger, FlexState, EnerVista,
CyberSentry, HardFiber, Digital Energy, Multilin, and GE Multilin are trademarks
or registered trademarks of GE Multilin Inc.
The contents of this manual are the property of GE Multilin Inc. This
documentation is furnished on license and may not be reproduced in whole or
in part without the permission of GE Multilin. The content of this manual is for
informational use only and is subject to change without notice.
Part number: 1601-0089-Z2 (September 2013)
TABLE OF CONTENTS
1. GETTING STARTED 1.1 IMPORTANT PROCEDURES

1.1.1 CAUTIONS AND WARNINGS ........................................................................... 1-1
1.1.2 INSPECTION PROCEDURE ............................................................................. 1-2
1.2 UR OVERVIEW
1.2.1 INTRODUCTION TO THE UR ........................................................................... 1-3
1.2.2 HARDWARE ARCHITECTURE ......................................................................... 1-3
1.2.3 SOFTWARE ARCHITECTURE.......................................................................... 1-5
1.2.4 IMPORTANT CONCEPTS ................................................................................. 1-5
1.3 ENERVISTA UR SETUP SOFTWARE
1.3.1 PC REQUIREMENTS ........................................................................................ 1-6
1.3.2 INSTALLATION.................................................................................................. 1-6
1.3.3 CONFIGURING THE D60 FOR SOFTWARE ACCESS .................................... 1-7
1.3.4 USING THE QUICK CONNECT FEATURE..................................................... 1-10
1.3.5 CONNECTING TO THE D60 RELAY .............................................................. 1-15
1.3.6 SETTING UP CYBERSENTRY AND CHANGING DEFAULT PASSWORD ... 1-16
1.4 UR HARDWARE
1.4.1 MOUNTING AND WIRING............................................................................... 1-18
1.4.2 COMMUNICATIONS........................................................................................ 1-18
1.4.3 FACEPLATE DISPLAY .................................................................................... 1-18
1.5 USING THE RELAY
1.5.1 FACEPLATE KEYPAD..................................................................................... 1-19
1.5.2 MENU NAVIGATION ....................................................................................... 1-19
1.5.3 MENU HIERARCHY ........................................................................................ 1-19
1.5.4 RELAY ACTIVATION....................................................................................... 1-19
1.5.5 RELAY PASSWORDS ..................................................................................... 1-20
1.5.6 FLEXLOGIC CUSTOMIZATION ...................................................................... 1-20
1.5.7 COMMISSIONING ........................................................................................... 1-21
2. PRODUCT DESCRIPTION 2.1 INTRODUCTION

2.1.1 OVERVIEW........................................................................................................ 2-1
2.1.2 SECURITY ......................................................................................................... 2-3
2.1.3 ORDERING........................................................................................................ 2-7
2.1.4 REPLACEMENT MODULES ........................................................................... 2-14
2.2 SPECIFICATIONS
2.2.1 PROTECTION ELEMENTS ............................................................................. 2-16
2.2.2 USER PROGRAMMABLE ELEMENTS ........................................................... 2-21
2.2.3 MONITORING .................................................................................................. 2-22
2.2.4 METERING ...................................................................................................... 2-23
2.2.5 INPUTS ............................................................................................................ 2-23
2.2.6 POWER SUPPLY ............................................................................................ 2-24
2.2.7 OUTPUTS ........................................................................................................ 2-25
2.2.8 COMMUNICATIONS........................................................................................ 2-26
2.2.9 INTER-RELAY COMMUNICATIONS ............................................................... 2-27
2.2.10 ENVIRONMENTAL .......................................................................................... 2-27
2.2.11 TYPE TESTS ................................................................................................... 2-28
2.2.12 PRODUCTION TESTS .................................................................................... 2-28
2.2.13 APPROVALS ................................................................................................... 2-29
2.2.14 MAINTENANCE ............................................................................................... 2-29
3. HARDWARE 3.1 DESCRIPTION

3.1.1 PANEL CUTOUT ............................................................................................... 3-1
3.1.2 REAR TERMINAL LAYOUT............................................................................... 3-6
3.2 WIRING
3.2.1 TYPICAL WIRING.............................................................................................. 3-8
3.2.2 DIELECTRIC STRENGTH ................................................................................. 3-9
3.2.3 CONTROL POWER ........................................................................................... 3-9
3.2.4 CT/VT MODULES ............................................................................................ 3-10
3.2.5 PROCESS BUS MODULES ............................................................................ 3-11
GE Multilin D60 Line Distance Protection System iii

TABLE OF CONTENTS
3.2.6 CONTACT INPUTS AND OUTPUTS................................................................3-12

3.2.7 TRANSDUCER INPUTS/OUTPUTS.................................................................3-20
3.2.8 RS232 FACEPLATE PORT ..............................................................................3-21
3.2.9 CPU COMMUNICATION PORTS.....................................................................3-21
3.2.10 IRIG-B ...............................................................................................................3-24
3.3 DIRECT INPUT AND OUTPUT COMMUNICATIONS
3.3.1 DESCRIPTION .................................................................................................3-25
3.3.2 FIBER: LED AND ELED TRANSMITTERS ......................................................3-27
3.3.3 FIBER-LASER TRANSMITTERS .....................................................................3-27
3.3.4 G.703 INTERFACE...........................................................................................3-28
3.3.5 RS422 INTERFACE .........................................................................................3-31
3.3.6 RS422 AND FIBER INTERFACE .....................................................................3-33
3.3.7 G.703 AND FIBER INTERFACE ......................................................................3-33
3.3.8 IEEE C37.94 INTERFACE................................................................................3-34
3.3.9 C37.94SM INTERFACE ...................................................................................3-38
4. HUMAN INTERFACES 4.1 ENERVISTA UR SETUP SOFTWARE INTERFACE

4.1.1 INTRODUCTION ................................................................................................4-1
4.1.2 CREATING A SITE LIST ....................................................................................4-1
4.1.3 ENERVISTA UR SETUP OVERVIEW ................................................................4-1
4.1.4 ENERVISTA UR SETUP MAIN WINDOW..........................................................4-3
4.2 EXTENDED ENERVISTA UR SETUP FEATURES
4.2.1 SETTINGS TEMPLATES ...................................................................................4-4
4.2.2 SECURING AND LOCKING FLEXLOGIC EQUATIONS....................................4-8
4.2.3 SETTINGS FILE TRACEABILITY.....................................................................4-10
4.3 FACEPLATE INTERFACE
4.3.1 FACEPLATE .....................................................................................................4-13
4.3.2 LED INDICATORS............................................................................................4-14
4.3.3 CUSTOM LABELING OF LEDS .......................................................................4-17
4.3.4 DISPLAY...........................................................................................................4-23
4.3.5 KEYPAD ...........................................................................................................4-23
4.3.6 BREAKER CONTROL ......................................................................................4-23
4.3.7 MENUS .............................................................................................................4-24
4.3.8 CHANGING SETTINGS ...................................................................................4-26
5. SETTINGS 5.1 OVERVIEW

5.1.1 SETTINGS MENU ..............................................................................................5-1
5.1.2 INTRODUCTION TO ELEMENTS ......................................................................5-4
5.1.3 INTRODUCTION TO AC SOURCES..................................................................5-5
5.2 PRODUCT SETUP
5.2.1 SECURITY..........................................................................................................5-8
5.2.2 DISPLAY PROPERTIES ..................................................................................5-23
5.2.3 CLEAR RELAY RECORDS ..............................................................................5-25
5.2.4 COMMUNICATIONS ........................................................................................5-26
5.2.5 MODBUS USER MAP ......................................................................................5-55
5.2.6 REAL TIME CLOCK .........................................................................................5-56
5.2.7 FAULT REPORTS ............................................................................................5-60
5.2.8 OSCILLOGRAPHY ...........................................................................................5-62
5.2.9 DATA LOGGER ................................................................................................5-64
5.2.10 USER-PROGRAMMABLE LEDS .....................................................................5-66
5.2.11 USER-PROGRAMMABLE SELF-TESTS .........................................................5-69
5.2.12 CONTROL PUSHBUTTONS ............................................................................5-69
5.2.13 USER-PROGRAMMABLE PUSHBUTTONS....................................................5-71
5.2.14 FLEX STATE PARAMETERS ..........................................................................5-76
5.2.15 USER-DEFINABLE DISPLAYS ........................................................................5-77
5.2.16 DIRECT INPUTS AND OUTPUTS....................................................................5-79
5.2.17 TELEPROTECTION .........................................................................................5-87
5.2.18 INSTALLATION ................................................................................................5-87
iv D60 Line Distance Protection System GE Multilin

TABLE OF CONTENTS
5.3 REMOTE RESOURCES

5.3.1 REMOTE RESOURCES CONFIGURATION ................................................... 5-89
5.4 SYSTEM SETUP
5.4.1 AC INPUTS ...................................................................................................... 5-90
5.4.2 POWER SYSTEM............................................................................................ 5-91
5.4.3 SIGNAL SOURCES ......................................................................................... 5-92
5.4.4 BREAKERS...................................................................................................... 5-95
5.4.5 DISCONNECT SWITCHES ............................................................................. 5-99
5.4.6 FLEXCURVES .............................................................................................. 5-102
5.4.7 PHASOR MEASUREMENT UNIT.................................................................. 5-109
5.5 FLEXLOGIC
5.5.1 INTRODUCTION TO FLEXLOGIC ................................................................ 5-131
5.5.2 FLEXLOGIC RULES ...................................................................................... 5-144
5.5.3 FLEXLOGIC EVALUATION ........................................................................... 5-144
5.5.4 FLEXLOGIC EXAMPLE ................................................................................. 5-145
5.5.5 FLEXLOGIC EQUATION EDITOR................................................................. 5-149
5.5.6 FLEXLOGIC TIMERS .................................................................................... 5-149
5.5.7 FLEXELEMENTS........................................................................................... 5-150
5.5.8 NON-VOLATILE LATCHES ........................................................................... 5-154
5.6 GROUPED ELEMENTS
5.6.1 OVERVIEW.................................................................................................... 5-155
5.6.2 SETTING GROUP ......................................................................................... 5-155
5.6.3 LINE PICKUP................................................................................................. 5-156
5.6.4 DISTANCE ..................................................................................................... 5-158
5.6.5 POWER SWING DETECT ............................................................................. 5-176
5.6.6 LOAD ENCROACHMENT.............................................................................. 5-185
5.6.7 PHASE CURRENT ........................................................................................ 5-187
5.6.8 NEUTRAL CURRENT.................................................................................... 5-197
5.6.9 WATTMETRIC GROUND FAULT .................................................................. 5-205
5.6.10 GROUND CURRENT..................................................................................... 5-208
5.6.11 NEGATIVE SEQUENCE CURRENT ............................................................. 5-210
5.6.12 BREAKER FAILURE ...................................................................................... 5-217
5.6.13 VOLTAGE ELEMENTS .................................................................................. 5-226
5.6.14 SENSITIVE DIRECTIONAL POWER............................................................. 5-237
5.7 CONTROL ELEMENTS
5.7.1 OVERVIEW.................................................................................................... 5-240
5.7.2 TRIP BUS....................................................................................................... 5-240
5.7.3 SETTING GROUPS ....................................................................................... 5-242
5.7.4 SELECTOR SWITCH..................................................................................... 5-244
5.7.5 TRIP OUTPUT ............................................................................................... 5-250
5.7.6 UNDERFREQUENCY.................................................................................... 5-256
5.7.7 OVERFREQUENCY ...................................................................................... 5-257
5.7.8 FREQUENCY RATE OF CHANGE................................................................ 5-258
5.7.9 SYNCHROCHECK......................................................................................... 5-260
5.7.10 AUTORECLOSE ............................................................................................ 5-264
5.7.11 DIGITAL ELEMENTS..................................................................................... 5-277
5.7.12 DIGITAL COUNTERS .................................................................................... 5-280
5.7.13 MONITORING ELEMENTS ........................................................................... 5-282
5.7.14 PILOT SCHEMES .......................................................................................... 5-302
5.8 INPUTS AND OUTPUTS
5.8.1 CONTACT INPUTS........................................................................................ 5-326
5.8.2 VIRTUAL INPUTS.......................................................................................... 5-328
5.8.3 CONTACT OUTPUTS.................................................................................... 5-329
5.8.4 VIRTUAL OUTPUTS ...................................................................................... 5-331
5.8.5 REMOTE DEVICES ....................................................................................... 5-332
5.8.6 REMOTE INPUTS.......................................................................................... 5-333
5.8.7 REMOTE DOUBLE-POINT STATUS INPUTS .............................................. 5-334
5.8.8 REMOTE OUTPUTS...................................................................................... 5-334
5.8.9 RESETTING................................................................................................... 5-335
5.8.10 DIRECT INPUTS AND OUTPUTS ................................................................. 5-336
5.8.11 TELEPROTECTION INPUTS AND OUTPUTS.............................................. 5-339
5.8.12 IEC 61850 GOOSE ANALOGS...................................................................... 5-341
5.8.13 IEC 61850 GOOSE INTEGERS..................................................................... 5-342
GE Multilin D60 Line Distance Protection System v

TABLE OF CONTENTS
5.9 TRANSDUCER INPUTS AND OUTPUTS

5.9.1 DCMA INPUTS ...............................................................................................5-343
5.9.2 RTD INPUTS ..................................................................................................5-344
5.9.3 DCMA OUTPUTS ...........................................................................................5-346
5.10 TESTING
5.10.1 TEST MODE ...................................................................................................5-349
5.10.2 FORCE CONTACT INPUTS...........................................................................5-350
5.10.3 FORCE CONTACT OUTPUTS.......................................................................5-351
5.10.4 PHASOR MEASUREMENT UNIT TEST VALUES .........................................5-352
6. ACTUAL VALUES 6.1 OVERVIEW

6.1.1 ACTUAL VALUES MENU ...................................................................................6-1
6.2 STATUS
6.2.1 CONTACT INPUTS ............................................................................................6-4
6.2.2 VIRTUAL INPUTS ..............................................................................................6-4
6.2.3 REMOTE INPUTS ..............................................................................................6-4
6.2.4 REMOTE DOUBLE-POINT STATUS INPUTS ...................................................6-5
6.2.5 TELEPROTECTION INPUTS .............................................................................6-5
6.2.6 CONTACT OUTPUTS ........................................................................................6-5
6.2.7 VIRTUAL OUTPUTS ..........................................................................................6-6
6.2.8 AUTORECLOSE.................................................................................................6-6
6.2.9 REMOTE DEVICES............................................................................................6-6
6.2.10 DIGITAL COUNTERS.........................................................................................6-7
6.2.11 SELECTOR SWITCHES ....................................................................................6-7
6.2.12 FLEX STATES ....................................................................................................6-8
6.2.13 ETHERNET ........................................................................................................6-8
6.2.14 REAL TIME CLOCK SYNCHRONIZING ............................................................6-8
6.2.15 DIRECT INPUTS ................................................................................................6-9
6.2.16 DIRECT DEVICES STATUS ............................................................................6-10
6.2.17 IEC 61850 GOOSE INTEGERS .......................................................................6-10
6.2.18 TELEPROTECTION CHANNEL TESTS...........................................................6-10
6.2.19 REMAINING CONNECTION STATUS .............................................................6-11
6.2.20 PARALLEL REDUNDANCY PROTOCOL (PRP) .............................................6-11
6.3 METERING
6.3.1 METERING CONVENTIONS ...........................................................................6-13
6.3.2 SOURCES ........................................................................................................6-16
6.3.3 SENSITIVE DIRECTIONAL POWER ...............................................................6-20
6.3.4 SYNCHROCHECK ...........................................................................................6-20
6.3.5 TRACKING FREQUENCY................................................................................6-20
6.3.6 FREQUENCY RATE OF CHANGE ..................................................................6-20
6.3.7 FLEXELEMENTS™ ..........................................................................................6-21
6.3.8 IEC 61580 GOOSE ANALOG VALUES ...........................................................6-21
6.3.9 WATTMETRIC GROUND FAULT.....................................................................6-22
6.3.10 PHASOR MEASUREMENT UNIT ....................................................................6-22
6.3.11 PMU AGGREGATOR .......................................................................................6-23
6.3.12 TRANSDUCER INPUTS AND OUTPUTS ........................................................6-23
6.4 RECORDS
6.4.1 FAULT REPORTS ............................................................................................6-24
6.4.2 EVENT RECORDS ...........................................................................................6-24
6.4.3 OSCILLOGRAPHY ...........................................................................................6-25
6.4.4 DATA LOGGER ................................................................................................6-25
6.4.5 PHASOR MEASUREMENT UNIT RECORDS .................................................6-25
6.4.6 BREAKER MAINTENANCE .............................................................................6-26
6.5 PRODUCT INFORMATION
6.5.1 MODEL INFORMATION ...................................................................................6-27
6.5.2 FIRMWARE REVISIONS..................................................................................6-27
7. COMMANDS AND 7.1 COMMANDS

TARGETS 7.1.1 COMMANDS MENU ...........................................................................................7-1
vi D60 Line Distance Protection System GE Multilin

TABLE OF CONTENTS
7.1.2 VIRTUAL INPUTS.............................................................................................. 7-1

7.1.3 CLEAR RECORDS ............................................................................................ 7-2
7.1.4 SET DATE AND TIME ....................................................................................... 7-2
7.1.5 RELAY MAINTENANCE .................................................................................... 7-3
7.1.6 PHASOR MEASUREMENT UNIT ONE-SHOT.................................................. 7-3
7.1.7 SECURITY ......................................................................................................... 7-5
7.2 TARGETS
7.2.1 TARGETS MENU............................................................................................... 7-6
7.2.2 TARGET MESSAGES ....................................................................................... 7-6
7.2.3 RELAY SELF-TESTS......................................................................................... 7-6
8. THEORY OF OPERATION 8.1 DISTANCE ELEMENTS

8.1.1 INTRODUCTION................................................................................................ 8-1
8.1.2 PHASOR ESTIMATION ..................................................................................... 8-1
8.1.3 DISTANCE CHARACTERISTICS ...................................................................... 8-2
8.1.4 MEMORY POLARIZATION................................................................................ 8-6
8.1.5 DISTANCE ELEMENTS ANALYSIS .................................................................. 8-7
8.2 PHASE DISTANCE APPLIED TO POWER TRANSFORMERS
8.2.1 DESCRIPTION................................................................................................. 8-11
8.2.2 EXAMPLE ........................................................................................................ 8-14
8.3 GROUND DIRECTIONAL OVERCURRENT
8.3.1 DESCRIPTION................................................................................................. 8-16
8.3.2 EXAMPLE ........................................................................................................ 8-16
8.4 SERIES COMPENSATED LINES
8.4.1 DESCRIPTION................................................................................................. 8-18
8.5 SINGLE-POLE TRIPPING
8.5.1 OVERVIEW...................................................................................................... 8-21
8.5.2 PHASE SELECTION........................................................................................ 8-24
8.5.3 COMMUNICATIONS CHANNELS FOR PILOT-AIDED SCHEMES ................ 8-25
8.5.4 PERMISSIVE ECHO SIGNALING ................................................................... 8-33
8.5.5 PILOT SCHEME / PHASE SELECTOR COORDINATION .............................. 8-34
8.5.6 CROSS-COUNTRY FAULT EXAMPLE ........................................................... 8-35
8.6 FAULT LOCATOR
8.6.1 FAULT TYPE DETERMINATION..................................................................... 8-36
9. APPLICATION OF 9.1 APPLICATION GUIDELINES

SETTINGS 9.1.1 INTRODUCTION................................................................................................ 9-1
9.1.2 IMPACT OF MEMORY POLARIZATION ........................................................... 9-1
9.1.3 HIGH-SET OVERCURRENT ELEMENTS ......................................................... 9-1
9.2 DISTANCE ELEMENTS (STEPPED DISTANCE SCHEME)
9.2.1 PHASE DISTANCE............................................................................................ 9-2
9.2.2 GROUND DISTANCE ........................................................................................ 9-3
9.3 PROTECTION SIGNALING SCHEMES
9.3.1 OVERVIEW........................................................................................................ 9-6
9.3.2 DIRECT UNDER-REACHING TRANSFER TRIP (DUTT) ................................. 9-6
9.3.3 PERMISSIVE UNDER-REACHING TRANSFER TRIP (PUTT) ......................... 9-6
9.3.4 PERMISSIVE OVER-REACHING TRANSFER TRIP (POTT) ........................... 9-6
9.3.5 HYBRID POTT SCHEME (HYB-POTT) ............................................................. 9-7
9.3.6 DIRECTIONAL COMPARISON BLOCKING ...................................................... 9-8
9.3.7 DIRECTIONAL COMPARISON UNBLOCKING................................................. 9-9
9.4 SERIES COMPENSATED LINES
9.4.1 INTRODUCTION.............................................................................................. 9-11
9.4.2 DISTANCE ....................................................................................................... 9-11
9.4.3 GROUND DIRECTIONAL OVERCURRENT ................................................... 9-12
9.4.4 HIGH-SET PHASE OVERCURRENT .............................................................. 9-12
9.5 PHASE DISTANCE THROUGH POWER TRANSFORMERS
9.5.1 PHASE DISTANCE PROTECTION ................................................................. 9-13
GE Multilin D60 Line Distance Protection System vii

TABLE OF CONTENTS
9.5.2 EXAMPLE .........................................................................................................9-14
10. MAINTENANCE 10.1 MODULES

10.1.1 REPLACE A MODULE .....................................................................................10-1
10.2 BATTERIES
10.2.1 REPLACE BATTERY .......................................................................................10-3
10.2.2 DISPOSE OF BATTERY ..................................................................................10-4
A. FLEXANALOG AND A.1 PARAMETER LISTS

FLEXINTEGER A.1.1 FLEXANALOG ITEMS ....................................................................................... A-1
A.1.2 FLEXINTEGER ITEMS .................................................................................... A-11
PARAMETERS
B. MODBUS B.1 MODBUS RTU PROTOCOL

COMMUNICATIONS B.1.1 INTRODUCTION ............................................................................................... B-1
B.1.2 PHYSICAL LAYER ............................................................................................ B-1
B.1.3 DATA LINK LAYER ........................................................................................... B-1
B.1.4 CRC-16 ALGORITHM ....................................................................................... B-2
B.2 MODBUS FUNCTION CODES
B.2.1 SUPPORTED FUNCTION CODES ................................................................... B-3
B.2.2 READ ACTUAL VALUES OR SETTINGS (FUNCTION CODE 03/04H) ........... B-3
B.2.3 EXECUTE OPERATION (FUNCTION CODE 05H)........................................... B-4
B.2.4 STORE SINGLE SETTING (FUNCTION CODE 06H)....................................... B-4
B.2.5 STORE MULTIPLE SETTINGS (FUNCTION CODE 10H) ................................ B-5
B.2.6 EXCEPTION RESPONSES............................................................................... B-5
B.3 FILE TRANSFERS
B.3.1 OBTAINING RELAY FILES VIA MODBUS........................................................ B-6
B.3.2 MODBUS PASSWORD OPERATION ............................................................... B-7
B.4 MEMORY MAPPING
B.4.1 MODBUS MEMORY MAP ................................................................................. B-9
B.4.2 DATA FORMATS............................................................................................. B-81
C. IEC 61850 C.1 OVERVIEW

COMMUNICATIONS C.1.1 INTRODUCTION ............................................................................................... C-1
C.1.2 COMMUNICATION PROFILES ......................................................................... C-1
C.2 SERVER DATA ORGANIZATION
C.2.1 OVERVIEW ....................................................................................................... C-2
C.2.2 GGIO1: DIGITAL STATUS VALUES ................................................................. C-2
C.2.3 GGIO2: DIGITAL CONTROL VALUES.............................................................. C-2
C.2.4 GGIO3: DIGITAL STATUS AND ANALOG VALUES FROM GOOSE DATA .... C-2
C.2.5 GGIO4: GENERIC ANALOG MEASURED VALUES......................................... C-2
C.2.6 MMXU: ANALOG MEASURED VALUES .......................................................... C-3
C.2.7 PROTECTION AND OTHER LOGICAL NODES............................................... C-3
C.3 SERVER FEATURES AND CONFIGURATION
C.3.1 BUFFERED/UNBUFFERED REPORTING........................................................ C-5
C.3.2 FILE TRANSFER ............................................................................................... C-5
C.3.3 TIMESTAMPS AND SCANNING ....................................................................... C-5
C.3.4 LOGICAL DEVICE NAME ................................................................................. C-5
C.3.5 LOCATION ........................................................................................................ C-5
C.3.6 LOGICAL NODE NAME PREFIXES.................................................................. C-6
C.3.7 CONNECTION TIMING ..................................................................................... C-6
C.3.8 NON-IEC 61850 DATA ...................................................................................... C-6
C.3.9 COMMUNICATION SOFTWARE UTILITIES..................................................... C-6
viii D60 Line Distance Protection System GE Multilin

TABLE OF CONTENTS
C.4 GENERIC SUBSTATION EVENT SERVICES: GSSE AND GOOSE

C.4.1 OVERVIEW........................................................................................................C-7
C.4.2 GSSE CONFIGURATION ..................................................................................C-7
C.4.3 FIXED GOOSE ..................................................................................................C-7
C.4.4 CONFIGURABLE GOOSE.................................................................................C-7
C.4.5 ETHERNET MAC ADDRESS FOR GSSE/GOOSE.........................................C-10
C.4.6 GSSE ID AND GOOSE ID SETTINGS ............................................................C-10
C.5 IEC 61850 IMPLEMENTATION VIA ENERVISTA UR SETUP
C.5.1 OVERVIEW......................................................................................................C-11
C.5.2 CONFIGURING IEC 61850 SETTINGS...........................................................C-12
C.5.3 ABOUT ICD FILES...........................................................................................C-13
C.5.4 CREATING AN ICD FILE WITH ENERVISTA UR SETUP ..............................C-17
C.5.5 ABOUT SCD FILES .........................................................................................C-17
C.5.6 IMPORTING AN SCD FILE WITH ENERVISTA UR SETUP ...........................C-20
C.6 ACSI CONFORMANCE
C.6.1 ACSI BASIC CONFORMANCE STATEMENT.................................................C-22
C.6.2 ACSI MODELS CONFORMANCE STATEMENT ............................................C-22
C.6.3 ACSI SERVICES CONFORMANCE STATEMENT .........................................C-23
C.7 LOGICAL NODES
C.7.1 LOGICAL NODES TABLE ...............................................................................C-26
D. IEC 60870-5-104 COMMS. D.1 IEC 60870-5-104 PROTOCOL

D.1.1 INTEROPERABILITY DOCUMENT ...................................................................D-1
D.1.2 POINTS LIST .....................................................................................................D-9
E. DNP COMMUNICATIONS E.1 DEVICE PROFILE DOCUMENT

E.1.1 DNP V3.00 DEVICE PROFILE ..........................................................................E-1
E.1.2 IMPLEMENTATION TABLE ...............................................................................E-4
E.2 DNP POINT LISTS
E.2.1 BINARY INPUT POINTS....................................................................................E-8
E.2.2 BINARY AND CONTROL RELAY OUTPUT ......................................................E-9
E.2.3 COUNTERS .....................................................................................................E-10
E.2.4 ANALOG INPUTS ............................................................................................E-11
F. RADIUS SERVER F.1 RADIUS SERVER CONFIGURATION

F.1.1 RADIUS SERVER CONFIGURATION............................................................... F-1
G. MISCELLANEOUS G.1 CHANGE NOTES

G.1.1 REVISION HISTORY ........................................................................................ G-1
G.1.2 CHANGES TO THE D60 MANUAL................................................................... G-2
G.2 ABBREVIATIONS
G.2.1 STANDARD ABBREVIATIONS ........................................................................ G-5
G.3 WARRANTY
G.3.1 GE MULTILIN WARRANTY .............................................................................. G-7
INDEX
GE Multilin D60 Line Distance Protection System ix

TABLE OF CONTENTS
x D60 Line Distance Protection System GE Multilin

1 GETTING STARTED 1.1 IMPORTANT PROCEDURES
1 GETTING STARTED 1.1IMPORTANT PROCEDURES

Use this chapter for initial setup of your new D60 Line Distance Protection System. 1
1.1.1 CAUTIONS AND WARNINGS
Before attempting to install or use the device, review all safety indicators in this document to help prevent injury, equipment
damage, or downtime.
The following safety and equipment symbols are used in this document.
Indicates a hazardous situation which, if not avoided, will result in death or serious injury.
Indicates a hazardous situation which, if not avoided, could result in death or serious injury.
Indicates a hazardous situation which, if not avoided, could result in minor or moderate
injury.
Indicates practices not related to personal injury.
a) GENERAL CAUTIONS AND WARNINGS

The following general safety precautions and warnings apply.
Ensure that all connections to the product are correct so as to avoid accidental risk of shock
and/or fire, for example such as can arise from high voltage connected to low voltage termi-
nals.
Follow the requirements of this manual, including adequate wiring size and type, terminal torque settings, voltage,
current magnitudes applied, and adequate isolation/clearance in external wiring from high to low voltage circuits.
Use the device only for its intended purpose and application.
Ensure that all ground paths are uncompromised for safety purposes during device operation and service.
Ensure that the control power applied to the device, the AC current, and voltage input match the ratings specified
on the relay nameplate. Do not apply current or voltage in excess of the specified limits.
Only qualified personnel are to operate the device. Such personnel must be thoroughly familiar with all safety cau-
tions and warnings in this manual and with applicable country, regional, utility, and plant safety regulations.
Hazardous voltages can exist in the power supply and at the device connection to current transformers, voltage
transformers, control, and test circuit terminals. Make sure all sources of such voltages are isolated prior to
attempting work on the device.
Hazardous voltages can exist when opening the secondary circuits of live current transformers. Make sure that
current transformer secondary circuits are shorted out before making or removing any connection to the current
transformer (CT) input terminals of the device.
For tests with secondary test equipment, ensure that no other sources of voltages or currents are connected to
such equipment and that trip and close commands to the circuit breakers or other switching apparatus are iso-
lated, unless this is required by the test procedure and is specified by appropriate utility/plant procedure.
When the device is used to control primary equipment, such as circuit breakers, isolators, and other switching
apparatus, all control circuits from the device to the primary equipment must be isolated while personnel are
working on or around this primary equipment to prevent any inadvertent command from this device.
Use an external disconnect to isolate the mains voltage supply.
LED transmitters are classified as IEC 60825-1 Accessible Emission Limit (AEL) Class 1M.
Class 1M devices are considered safe to the unaided eye. Do not view directly with optical
instruments.
This product is rated to Class A emissions levels and is to be used in Utility, Substation Industrial
environments. Not to be used near electronic devices rated for Class B levels.
GE Multilin D60 Line Distance Protection System 1-1

1.1 IMPORTANT PROCEDURES 1 GETTING STARTED
1.1.2 INSPECTION PROCEDURE
1 1. Open the relay packaging and inspect the unit for physical damage.
2. View the rear nameplate and verify that the correct model has been ordered and delivered.
Figure 1–1: REAR NAMEPLATE (EXAMPLE)

3. Ensure that the following items are included:
• Instruction manual (if ordered)
• GE EnerVista™ CD (includes the EnerVista UR Setup software and manuals in PDF format)
• Mounting screws
4. If there is any noticeable physical damage, or any of the contents listed are missing, please contact GE Digital Energy
immediately as follows.
GE DIGITAL ENERGY CONTACT INFORMATION AND CALL CENTER FOR PRODUCT SUPPORT:
GE Digital Energy
650 Markland Street
Markham, Ontario
Canada L6C 0M1
TELEPHONE: Worldwide +1 905 927 7070
Europe/Middle East/Africa +34 94 485 88 54
North America toll-free 1 800 547 8629
FAX: +1 905 927 5098
E-MAIL: Worldwide multilin.tech@ge.com
Europe multilin.tech.euro@ge.com
HOME PAGE: http://www.gedigitalenergy.com/multilin
For updates to the instruction manual, firmware, and software, visit the GE Digital Energy website.
1-2 D60 Line Distance Protection System GE Multilin

1 GETTING STARTED 1.2 UR OVERVIEW
1.2UR OVERVIEW 1.2.1 INTRODUCTION TO THE UR
The GE Universal Relay (UR) series is a new generation of digital, modular, and multifunction equipment that is easily
1
incorporated into automation systems, at both the station and enterprise levels.
1.2.2 HARDWARE ARCHITECTURE
a) UR BASIC DESIGN
The UR is a digital-based device containing a central processing unit (CPU) that handles multiple types of input and output
signals. The UR device can communicate over a local area network (LAN) with an operator interface, a programming
device, or another UR device.
Figure 1–2: UR BLOCK DIAGRAM

The CPU module contains firmware that provides protection elements in the form of logic algorithms, as well as program-
mable logic gates, timers, and latches for control features.
Input elements accept a variety of analog or digital signals from the field. The UR isolates and converts these signals into
logic signals used by the relay.
Output elements convert and isolate the logic signals generated by the relay into digital or analog signals that can be used
to control field devices.
The software and unit are backwards-compatible with UR devices.
b) UR SIGNAL TYPES
The contact inputs and outputs are digital signals associated with connections to hard-wired contacts. Both ‘wet’ and ‘dry’
contacts are supported.
The virtual inputs and outputs are digital signals associated with UR-series internal logic signals. Virtual inputs include
signals generated by the local user interface. The virtual outputs are outputs of FlexLogic™ equations used to customize
the device. Virtual outputs can also serve as virtual inputs to FlexLogic equations.
The analog inputs and outputs are signals that are associated with transducers, such as Resistance Temperature Detec-
tors (RTDs).
The CT and VT inputs refer to analog current transformer and voltage transformer signals used to monitor AC power lines.
The UR-series relays support 1 A and 5 A CTs.
The remote inputs and outputs provide a means of sharing digital point state information between remote UR-series
devices. The remote outputs interface to the remote inputs of other UR-series devices. Remote outputs are FlexLogic oper-
ands inserted into IEC 61850 GSSE and GOOSE messages.

1.2 UR OVERVIEW 1 GETTING STARTED
The direct inputs and outputs provide a means of sharing digital point states between a number of UR-series IEDs over
1 dedicated fiber (single or multimode), RS422, or G.703 interface. No switching equipment is required as the IEDs are con-
nected directly in a ring or redundant (dual) ring configuration. This feature is optimized for speed and intended for pilot-
aided schemes, distributed logic applications, or the extension of the input/output capabilities of a single relay chassis.
c) UR SCAN OPERATION
The UR-series devices operate in a cyclic scan fashion. The device reads the inputs into an input status table, solves the
logic program (FlexLogic equation), and then sets each output to the appropriate state in an output status table. Any result-
ing task execution is priority interrupt-driven.
Figure 1–3: UR-SERIES SCAN OPERATION

1 GETTING STARTED 1.2 UR OVERVIEW
1.2.3 SOFTWARE ARCHITECTURE
Firmware is the software embedded in the relay and is designed in functional modules that can be installed in any relay as
1
required. This is achieved with object-oriented design and programming (OOD/OOP) techniques.
Object-oriented techniques involve the use of objects and classes. An object is defined as “a logical entity that contains
both data and code that manipulates that data”. A class is the generalized form of similar objects. By using this concept,
one can create a protection class with the protection elements as objects of the class, such as time overcurrent, instanta-
neous overcurrent, current differential, undervoltage, overvoltage, underfrequency, and distance. These objects represent
completely self-contained software modules. The same object-class concept can be used for metering, input/output control,
software interface, communications, or any functional entity in the system.
Employing OOD/OOP in the software architecture of the D60 achieves the same features as the hardware architecture:
modularity, scalability, and flexibility. The application software for any UR-series device (for example, feeder protection,
transformer protection, distance protection) is constructed by combining objects from the various functional classes. This
results in a common interface across the UR series.
1.2.4 IMPORTANT CONCEPTS
As described above, the architecture of the UR-series relays differ from previous devices. To achieve a general understand-
ing of this device, some sections of Chapter 5 are quite helpful. The most important functions of the relay are contained in
“elements”. A description of the UR-series elements can be found in the Introduction to elements section in chapter 5.
Examples of simple elements, and some of the organization of this manual, can be found in the Control elements section of
chapter 5. An explanation of the use of inputs from CTs and VTs is in the Introduction to AC sources section in chapter 5. A
description of how digital signals are used and routed within the relay is contained in the Introduction to FlexLogic section in
chapter 5.

1.3 ENERVISTA UR SETUP SOFTWARE 1 GETTING STARTED
1.3ENERVISTA UR SETUP SOFTWARE 1.3.1 PC REQUIREMENTS
1 The relay front panel or the EnerVista UR Setup software can be used to communicate with the relay. The EnerVista UR
Setup software interface is the preferred method to edit settings and view actual values because the computer monitor can
display more information.
The minimum system requirements for the EnerVista UR Setup software are as follows:
• Pentium 4 (Core Duo recommended)
• Windows XP with Service Pack 2 (Service Pack 3 recommended), Windows 7, or Windows Server 2008 Release 2
64-bit
• 1 GB of RAM (2 GB recommended)
• 500 MB free hard drive space (1 GB recommended)
• 1024 x 768 display (1280 x 800 recommended)
The following qualified modems have been tested to be compliant with the D60 and the EnerVista UR Setup software:
• US Robotics external 56K FaxModem 5686
• US Robotics external Sportster 56K X2
• PCTEL 2304WT V.92 MDC internal modem
1.3.2 INSTALLATION
After ensuring that the requirements for using EnerVista UR Setup are met (previous section), install the EnerVista UR
Setup software from the GE EnerVista DVD. Or download the UR EnerVista software from
http://www.gedigitalenergy.com/multilin and install it.
If you are upgrading from version 7.0 or 7.1 to 7.2 or later, some CPU modules require a new boot version. Update this first
in EnerVista under Maintenance > Update Firmware.
To install the UR EnerVista software from the DVD:
1. Insert the GE EnerVista DVD into the DVD drive of your computer.
2. Click the Install Now button and follow the instructions.
3. When installation is complete, start the EnerVista Launchpad application.
4. Click the IED Setup section of the Launch Pad window.
Figure 1–4: ADDING UR DEVICE IN LAUNCHPAD WINDOW

5. In the EnerVista Launch Pad window, click the Add Product button and select the appropriate product, shown as fol-
lows. Select the Web option to ensure the most recent software release, or select CD if you do not have a web connec-

1 GETTING STARTED 1.3 ENERVISTA UR SETUP SOFTWARE
tion, then click the Add Now button to list software items for the product. EnerVista Launchpad then obtains the
software from the Internet or DVD and automatically starts the installation program.
1
Figure 1–5: IDENTIFYING THE UR DEVICE TYPE

6. Select the complete path, including the new directory name, where the EnerVista UR Setup is to be installed.
7. Click the Next button to begin the installation. The files are installed in the directory indicated, and the installation pro-
gram automatically creates icons and adds EnerVista UR Setup to the Windows start menu.
8. Click Finish to complete the installation. The UR device is added to the list of installed intelligent electronic devices
(IEDs) in the EnerVista Launchpad window, as shown.
Figure 1–6: UR DEVICE ADDED TO LAUNCHPAD WINDOW
1.3.3 CONFIGURING THE D60 FOR SOFTWARE ACCESS
a) OVERVIEW
You connect remotely to the D60 through the rear RS485 or Ethernet port with a computer running the EnerVista UR Setup
software. The D60 can also be accessed locally with a laptop computer through the front panel RS232 port or the rear
Ethernet port using the Quick Connect feature.
• To configure the D60 for remote access via the rear RS485 port, see the Configuring Serial Communications section.
• To configure the D60 for remote access via the rear Ethernet port, see the Configuring Ethernet Communications sec-
tion. An Ethernet module must be specified at the time of ordering.
• To configure the D60 for local access with a laptop through either the front RS232 port or rear Ethernet port, see the
Using the Quick Connect Feature section.

b) CONFIGURING SERIAL COMMUNICATIONS
1 A GE Multilin F485 converter (or compatible RS232-to-RS485 converter) is required. See the F485 instruction manual for
details.
1. Connect a serial cable to the RS485 terminal on the back of the UR device.
2. In the EnerVista Launchpad software on the computer, select the UR device to start the software.
3. Click the Device Setup button to open the Device Setup window, and click the Add Site button to define a new site.
4. Enter a site name in the Site Name field. Optionally add a short description of the site along with the display order of
devices defined for the site. This example uses “Location 1” as the site name. When done, click the OK button. The
new site appears in the upper-left list in the EnerVista UR Setup window.
5. Click the Device Setup button, then select the new site to re-open the Device Setup window.
6. Click the Add Device button to define the new device.
7. Enter a name in the "Device Name” field and a description (optional) of the site.
8. Select “Serial” from the Interface drop-down list. This displays a number of interface parameters that must be entered
for serial communications.
Figure 1–7: CONFIGURING SERIAL COMMUNICATIONS

9. Enter the relay slave address, COM port, baud rate, and parity settings from the SETTINGS  PRODUCT SETUP  COM-
MUNICATIONS  SERIAL PORTS menu in their respective fields.
10. Click the Read Order Code button to connect to the D60 device and upload the order code. If a communications error
occurs, ensure that the EnerVista UR Setup serial communications values entered in the previous step correspond to
the relay setting values.
11. Click the OK button when the relay order code has been received. The new device is added to the Site List window (or
Online window) located in the top left corner of the main EnerVista UR Setup window.
The device has now been configured for RS232 communications. Proceed to the Connecting to the D60 section to begin
communication.

c) CONFIGURING ETHERNET COMMUNICATIONS

Before starting, verify that the Ethernet network cable is properly connected to the Ethernet port on the back of the relay. To
setup the relay for Ethernet communications, you define a Site, then add the relay as a Device at that site.The computer
1
and UR device must be on the same subnet.
12. Select the “UR” device from the EnerVista Launchpad to start EnerVista UR Setup.
13. Click the Device Setup button to open the Device Setup window, then click the Add Site button to define a new site.
14. Enter the desired site name in the “Site Name” field. If desired, a short description of site can also be entered along
with the display order of devices defined for the site. In this example, we use “Location 2” as the site name. Click the
OK button when complete.
15. The new site appears in the upper-left list in the EnerVista UR Setup window. Click the Device Setup button then
select the new site to re-open the Device Setup window.
16. Click the Add Device button to define the new device.
17. Enter the desired name in the “Device Name” field and a description (optional) of the site.
18. Select “Ethernet” from the Interface drop-down list. This displays a number of interface parameters that must be
entered for proper Ethernet functionality.
Figure 1–8: CONFIGURING ETHERNET COMMUNICATIONS

19. Enter the relay IP address specified in the SETTINGS  PRODUCT SETUP  COMMUNICATIONS  NETWORK  IP
ADDRESS in the “IP Address” field.
20. Enter the relay slave address and Modbus port address values from the respective settings in the SETTINGS  PROD-
UCT SETUP  COMMUNICATIONS  MODBUS PROTOCOL menu.
21. Click the Read Order Code button to connect to the D60 device and upload the order code. If an communications
error occurs, ensure that the three EnerVista UR Setup values entered in the previous steps correspond to the relay
setting values.
22. Click OK when the relay order code has been received. The new device is added to the Site List window (or Online
window) located in the top left corner of the main EnerVista UR Setup window.
The Site Device has now been configured for Ethernet communications. Proceed to the Connecting to the D60 section to
begin communications.

1.3.4 USING THE QUICK CONNECT FEATURE
1 a) USING QUICK CONNECT VIA THE FRONT PANEL RS232 PORT

Before starting, verify that the serial cable is properly connected from the computer to the front panel RS232 port with a
straight-through 9-pin to 9-pin RS232 cable.
1. Verify that the latest version of the EnerVista UR Setup software is installed (available from the GE EnerVista CD or
online from http://www.gedigitalenergy.com/multilin). See the Software Installation section if not already installed.
3. Click the Quick Connect button to open the Quick Connect dialog box.
4. Select the Serial interface and the correct COM Port, then click Connect.
5. The EnerVista UR Setup software creates a site named “Quick Connect” with a corresponding device also named
“Quick Connect” and displays them at the upper-left of the screen. Expand the sections to view data directly from the
D60 device.
Each time that the EnerVista UR Setup software is initialized, click the Quick Connect button to establish direct communi-
cations to the D60 device. This ensures that configuration of the EnerVista UR Setup software matches the D60 model
number.
b) USING QUICK CONNECT VIA THE REAR ETHERNET PORTS

To use the Quick Connect feature to access the D60 from a computer through Ethernet, first assign an IP address to the
relay from the front panel keyboard.
1. Press the MENU key until the SETTINGS menu displays.
2. Navigate to the SETTINGS  PRODUCT SETUP  COMMUNICATIONS  NETWORK  IP ADDRESS setting.
3. Enter an IP address, for example “1.1.1.1,” and select the ENTER key to save the value.
4. In the same menu, select the SUBNET IP MASK setting.
5. Enter a subnet IP address, for example “255.0.0.0,” and press the ENTER key to save the value.
Next, use an Ethernet cross-over cable to connect the computer to the rear Ethernet port. In case you need it, the figure
shows the pinout for an Ethernet cross-over cable.
3 4 5 6
END 1 END 2
2 7 Pin Wire color Diagram Pin Wire color Diagram
1 8 1 White/orange 1 White/green
2 Orange 2 Green
3 White/green 3 White/orange
4 Blue 4 Blue
5 White/blue 5 White/blue
6 Green 6 Orange
7 White/brown 7 White/brown
8 Brown 8 Brown
842799A1.CDR
Figure 1–9: ETHERNET CROSS-OVER CABLE PIN LAYOUT

Now, assign the computer an IP address compatible with the relay’s IP address.

1. From the Windows desktop, right-click the My Network Places icon and select Properties to open the network con-
nections window.
1
2. Right-click the Local Area Connection icon and select Properties.
3. Select the Internet Protocol (TCP/IP) item from the list, and click the Properties button.
4. Click the “Use the following IP address” box.

5. Enter an IP address with the first three numbers the same as the IP address of the D60 relay and the last number dif-
1 6.
ferent (in this example, 1.1.1.2).
Enter a subnet mask equal to the one set in the D60 (in this example, 255.0.0.0).
7. Click the OK button to save the values.
Before continuing, test the Ethernet connection.
1. Open a Windows console window by selecting Start > Run from the Windows Start menu and typing “cmd”.
2. Type the following command, substituting the IP address of 1.1.1.1 with yours:
C:\WINNT>ping 1.1.1.1
3. If the connection is successful, the system returns four replies similar to the following:
Pinging 1.1.1.1 with 32 bytes of data:
Reply from 1.1.1.1: bytes=32 time<10ms TTL=255
Ping statistics for 1.1.1.1:
Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip time in milliseconds:
Minimum = 0ms, Maximum = 0ms, Average = 0 ms
4. Note that the values for time and TTL vary depending on local network configuration.
5. If the following sequence of messages appears when entering the C:\WINNT>ping 1.1.1.1 command:
Request timed out.
Request timed out.
Request timed out.
Request timed out.
verify the physical connection between the D60 and the laptop computer, and double-check the programmed IP
address in the PRODUCT SETUP  COMMUNICATIONS  NETWORK  IP ADDRESS setting, then repeat step 2.
Hardware error.
Hardware error.
Hardware error.
Hardware error.
verify the physical connection between the D60 and the laptop computer, and double-check the programmed IP
address in the PRODUCT SETUP  COMMUNICATIONS  NETWORK  IP ADDRESS setting, then repeat step 2.


Destination
Destination
host
host
unreachable.
unreachable.
1
Destination host unreachable.
Destination host unreachable.
verify the IP address is programmed in the local computer by entering the ipconfig command in the command window.
C:\WINNT>ipconfig
Windows IP Configuration
Ethernet adapter <F4FE223E-5EB6-4BFB-9E34-1BD7BE7F59FF>:
Connection-specific DNS suffix. . :
IP Address. . . . . . . . . . . . : 0.0.0.0
Subnet Mask . . . . . . . . . . . : 0.0.0.0
Default Gateway . . . . . . . . . :
Ethernet adapter Local Area Connection:
Connection-specific DNS suffix . :
IP Address. . . . . . . . . . . . : 1.1.1.2
Subnet Mask . . . . . . . . . . . : 255.0.0.0
Default Gateway . . . . . . . . . :
C:\WINNT>
Before using the Quick Connect feature through the Ethernet port, disable any configured proxy settings in Internet
Explorer.
1. Start the Internet Explorer software.
2. Select the Tools > Internet Options menu item and click the Connections tab.
3. Click on the LAN Settings button to open the following window.
4. Ensure that the “Use a proxy server for your LAN” box is not checked.
If this computer is used to connect to the Internet, re-enable any proxy server settings after the laptop has been discon-
nected from the D60 relay.
1. Start the Internet Explorer software.

3. Click the Quick Connect button to open the Quick Connect dialog box.
4. Select the Ethernet interface and enter the IP address assigned to the D60, then click the Connect button. The
EnerVista UR Setup software creates a site named “Quick Connect” with a corresponding device also named “Quick
Connect” and displays them at the upper-left of the screen.
5. Expand the sections to view data directly from the D60 device.
Each time the EnerVista UR Setup software is initialized, click the Quick Connect button to establish direct communica-
tions to the D60. This ensures that configuration of the EnerVista UR Setup software matches the D60 model number.
When direct communications with the D60 via Ethernet is complete, make the following changes:
1. From the Windows desktop, right-click the My Network Places icon and select Properties to open the network con-
nections window.
2. Right-click the Local Area Connection icon and select the Properties item.
3. Select the Internet Protocol (TCP/IP) item from the list provided and click the Properties button.
4. Set the computer to “Obtain a relay address automatically” as shown.
If this computer is used to connect to the Internet, re-enable any proxy server settings after the computer has been discon-
nected from the D60 relay.
AUTOMATIC DISCOVERY OF ETHERNET DEVICES
The EnerVista UR Setup software can automatically discover and communicate to all UR-series IEDs located on an Ether-
net network.
Using the Quick Connect feature, a single click of the mouse triggers the software to automatically detect any UR-series
relays located on the network. The EnerVista UR Setup software then proceeds to configure all settings and order code
options in the Device Setup menu. This feature allows the user to identify and interrogate all UR-series devices at a loca-
tion.

1.3.5 CONNECTING TO THE D60 RELAY
1. Open the Display Properties window through the Site List tree as shown. The Display Properties window opens with a
1
status indicator on the lower left of the EnerVista UR Setup window.
Quick action hot links
Expand the site list by double-clicking

or selecting the +/– box.
Communications status indicators:

Green = OK
Red = No communications
UR icon = report is open
842743A3.CDR
2. If the status indicator is red, verify that the Ethernet network cable is properly connected to the Ethernet port on the
back of the relay and that the relay has been properly setup for communications (steps A and B earlier).
If a relay icon appears in place of the status indicator, than a report (such as an oscillography or event record) is open.
Close the report to re-display the green status indicator.
3. The Display Properties settings can now be edited, printed, or changed.
See chapter 4 in this manual or the EnerVista UR Setup Help File for information about the using the EnerVista UR
Setup software interface.
NOTE
QUICK ACTION HOT LINKS

The EnerVista UR Setup software has several quick action buttons to provide instant access to several functions that are
often performed when using D60 relays. From the online window, users can select the relay to interrogate from a pull-down
window, then click the button for the action they want to perform. The following quick action functions are available:
• View the D60 event record
• View the last recorded oscillography record
• View the status of all D60 inputs and outputs
• View all of the D60 metering values
• View the D60 protection summary
• Generate a service report

1.3.6 SETTING UP CYBERSENTRY AND CHANGING DEFAULT PASSWORD
1 If and when first using CyberSentry security, use the following procedure for set up.
1. Log in to the relay as Administrator by using the Value keys on the front panel or through EnerVista connected serially
(so that no IP address is required). If logging in through EnerVista choose Device authentication. Enter the default
password "ChangeMe1#". Note that the "Lock relay" setting needs to be disabled in the Security > Supervisory
menu. When this setting is disabled, configuration and firmware upgrade are possible. By default, this setting is dis-
abled.
2. Enable the Supervisor role if you have a need for it.
3. Make any required changes in configuration, such as setting a valid IP address for communication over Ethernet.
4. Log out of the Administrator account by choosing None.
Next, device or server authentication can be chosen on the login screen, but the choice is available only in EnerVista. Use
device authentication to log in using the five pre-configured roles (Administrator, Supervisor, Engineer, Operator,
Observer). When using a serial connection, only device authentication is supported. When server authentication is
required, characteristics for communication with a RADIUS server must be configured on the UR. This is possible only
through the EnerVista software. The RADIUS server itself also must be configured. The appendix called RADIUS Server
gives an example of how to setup a simple RADIUS server. Once both the RADIUS server and the parameters for connect-
ing UR to the server have been configured, you can choose server authentication on the login screen of EnerVista.
Figure 1–10: LOGIN SCREEN FOR CYBERSENTRY
During the commissioning phase, you have the option to bypass the use of passwords. Do so by enabling the Bypass
Access setting under SETTINGS > PRODUCT SETUP > SECURITY > SUPERVISORY. Be sure to disable this bypass setting after
commissioning the device.
You can change the password for any role either from the front panel or through EnerVista.

If using EnerVista, navigate to Settings > Product Setup > Security. Change the Local Administrator Password, for
example. It is strongly recommended that the password for the Administrator be changed from the default. Changing the
passwords for the other three roles is optional. 1
Figure 1–11: CHANGING THE DEFAULT PASSWORD

1.4 UR HARDWARE 1 GETTING STARTED
1.4UR HARDWARE 1.4.1 MOUNTING AND WIRING
1 See Chapter 3: Hardware for mounting and wiring instructions.
1.4.2 COMMUNICATIONS
The EnerVista UR Setup software communicates to the relay via the faceplate RS232 port or the rear panel RS485 / Ether-
net ports. To communicate via the faceplate RS232 port, a standard straight-through serial cable is used. The DB-9 male
end is connected to the relay and the DB-9 or DB-25 female end is connected to the computer COM2 port as described in
the CPU communications ports section of chapter 3.
Figure 1–12: RELAY COMMUNICATION OPTIONS

To communicate through the D60 rear RS485 port from a computer RS232 port, the GE Multilin RS232/RS485 converter
box is required. This device (catalog number F485) connects to the computer using a straight-through serial cable. A
shielded twisted-pair (20, 22, or 24 AWG) connects the F485 converter to the D60 rear communications port. The converter
terminals (+, –, GND) are connected to the D60 communication module (+, –, COM) terminals. See the CPU communica-
tions ports section in chapter 3 for details. The line is terminated with an R-C network (that is, 120 , 1 nF) as described in
the chapter 3.
1.4.3 FACEPLATE DISPLAY
All messages are displayed on a backlit liquid crystal display (LCD) to make them visible under poor lighting conditions.
While the keypad and display are not actively being used, the display defaults to user-defined messages. Any high-priority
event-driven message automatically overrides the default message and appears on the display.

1 GETTING STARTED 1.5 USING THE RELAY
1.5USING THE RELAY 1.5.1 FACEPLATE KEYPAD
Display messages are organized into pages under the following headings: actual values, settings, commands, and targets.
1
The MENU key navigates through these pages. Each heading page is divided further into logical subgroups.
The MESSAGE keys navigate through the subgroups. The VALUE keys increment or decrement numerical setting values
when in programming mode. These keys also scroll through alphanumeric values in the text edit mode. Alternatively, val-
ues can be entered with the numeric keypad.
The decimal key initiates and advances to the next character in text edit mode or enters a decimal point.
The HELP key can be pressed at any time for context-sensitive help messages.
The ENTER key stores altered setting values.
1.5.2 MENU NAVIGATION
Press the MENU key to select a header display page (top-level menu). The header title appears momentarily followed by a
header display page menu item. Each press of the MENU key advances through the following main heading pages:
• Actual values
• Settings
• Commands
• Targets
• User displays (when enabled)
1.5.3 MENU HIERARCHY
The setting and actual value messages are arranged hierarchically. The header display pages are indicated by double
scroll bar characters (), while sub-header pages are indicated by single scroll bar characters (). The header display
pages represent the highest level of the hierarchy and the sub-header display pages fall below this level. The MESSAGE
UP and DOWN keys move within a group of headers, sub-headers, setting values, or actual values. Continually pressing
the MESSAGE RIGHT key from a header display displays specific information for the header category. Conversely, contin-
ually pressing the MESSAGE LEFT key from a setting value or actual value display returns to the header display.
HIGHEST LEVEL LOWEST LEVEL (SETTING

VALUE)
 SETTINGS  PASSWORD ACCESS LEVEL:

 PRODUCT SETUP  SECURITY Restricted
 SETTINGS
 SYSTEM SETUP
1.5.4 RELAY ACTIVATION
The relay is in the default “Not Programmed” state when it leaves the factory. When powered up successfully, the Trouble
LED is on and the In Service LED off. The relay in the “Not Programmed” state blocks signaling of any output relay. These
conditions remain until the relay is explicitly put in the “Programmed” state.
Select the menu message SETTINGS  PRODUCT SETUP  INSTALLATION  RELAY SETTINGS
RELAY SETTINGS:
Not Programmed
1. To put the relay in the “Programmed” state, press either of the VALUE keys once and then press ENTER. The face-
plate Trouble LED turns off and the In Service LED turns on.

1.5 USING THE RELAY 1 GETTING STARTED
The settings for the relay can be programmed manually (see Chapter 5) via the faceplate keypad or remotely via the
1 EnerVista UR Setup software (see the EnerVista UR Setup help file).
1.5.5 RELAY PASSWORDS
a) PASSWORD SECURITY
It is recommended that passwords be set for each security level and assigned to specific personnel. There are two user
security access levels, COMMAND and SETTING.
1. COMMAND
The COMMAND access level restricts the user from making any settings changes, but allows the user to perform the fol-
lowing operations:
• Operate breakers via faceplate keypad
• Change state of virtual inputs
• Clear event records
• Clear oscillography records
• Operate user-programmable pushbuttons
2. SETTING
The SETTING access level allows the user to make any changes to any of the setting values.
See the Changing Settings section in Chapter 4 for complete instructions on setting security-level passwords.
NOTE
b) CYBERSENTRY
When the CyberSentry option is purchased, advanced security services are available, using either device authentication or
server authentication using RADIUS. When this option is purchased, the basic password security is disabled automatically.
For more information, see the CyberSentry content in the Security section of the next chapter.
1.5.6 FLEXLOGIC CUSTOMIZATION
FlexLogic equation editing is required for setting user-defined logic for customizing the relay operations. See the FlexLogic
section in Chapter 5.

1 GETTING STARTED 1.5 USING THE RELAY
1.5.7 COMMISSIONING
The D60 requires minimal maintenance after it is commissioned into service. Since the D60 is a microprocessor-based
1
relay, its characteristics do not change over time. As such, no further functional tests are required.
The D60 performs a number of continual self-tests and takes the necessary action in case of any major errors (see the
Relay Self-tests section in chapter 7). However, it is recommended that D60 maintenance be scheduled with other system
maintenance. This maintenance can involve in-service, out-of-service, or unscheduled maintenance.
In-service maintenance:
1. Visual verification of the analog values integrity, such as voltage and current (in comparison to other devices on the
corresponding system).
2. Visual verification of active alarms, relay display messages, and LED indications.
3. LED test.
4. Visual inspection for any damage, corrosion, dust, or loose wires.
5. Event recorder file download with further events analysis.
Out-of-service maintenance:
1. Check wiring connections for firmness.
2. Analog values (currents, voltages, RTDs, analog inputs) injection test and metering accuracy verification. Calibrated
test equipment is required.
3. Protection elements setting verification (analog values injection or visual verification of setting file entries against relay
settings schedule).
4. Contact inputs and outputs verification. This test can be conducted by direct change of state forcing or as part of the
system functional testing.
5. Visual inspection for any damage, corrosion, or dust.
6. Event recorder file download with further events analysis.
7. LED Test and pushbutton continuity check.
Unscheduled maintenance, such as a disturbance causing system interruption:
1. View the event recorder and oscillography or fault report for correct operation of inputs, outputs, and elements.
If it is concluded that the relay or one of its modules is of concern, contact GE Multilin for service.

1.5 USING THE RELAY 1 GETTING STARTED

2 PRODUCT DESCRIPTION 2.1 INTRODUCTION
2 PRODUCT DESCRIPTION 2.1INTRODUCTION 2.1.1 OVERVIEW
The D60 Line Distance Protection System is a microprocessor-based relay intended for use on transmission lines of any
voltage level, without, with, and in the vicinity of series compensation, in three-pole and single-pole tripping applications.
The primary function of the relay consists of five phase and ground distance zones of protection, either mho or quadrilateral
as per user selection, with built-in logic for the five common pilot-aided schemes. The distance elements are optimized to
provide good measurement accuracy with a fast operating time, even when used with capacitive voltage transformers
(CVTs), and can be supervised by detection of power swings. The relay also provides directional ground overcurrent ele-
ments, which are commonly used as part of an overall line protection system.
2
D60 phase distance zones can be configured to work with voltages and currents fed from VTs and CTs located indepen-
dently from one another on either side of a three-phase power transformer. The relay compensates accordingly to preserve
reach and correct target information regardless of the location and type of fault. This feature allows backup protection appli-
cations for generators and power transformers.
A close-into-fault (or switch-on-to-fault) function is performed by the line pickup element. Out-of-step tripping, three-pole/
single-pole dual-breaker autoreclosing, synchrocheck, fault location, and many other functions are also available. In addi-
tion, overcurrent and undervoltage protection, fault diagnostics, power metering, and RTU functions are provided. The D60
provides phase, neutral, and ground time overcurrent protection. The time overcurrent functions can be programmed with
multiple curve shapes or FlexCurve™ for optimum coordination.
Voltage, current, and power metering is built into the relay as a standard feature. Current parameters are available as total
waveform RMS magnitude, or as fundamental frequency only RMS magnitude and angle (phasor).
Diagnostic features include an event recorder capable of storing 1024 time-tagged events, oscillography capable of storing
up to 64 records with programmable trigger, content and sampling rate, and data logger acquisition of up to 16 channels,
with programmable content and sampling rate. The internal clock used for time-tagging can be synchronized with an IRIG-
B signal or via the SNTP protocol over the Ethernet port. This precise time stamping allows the sequence of events to be
determined throughout the system. Events can also be programmed (via FlexLogic™ equations) to trigger oscillography
data capture which may be set to record the measured parameters before and after the event for viewing on a personal
computer (PC). These tools significantly reduce troubleshooting time and simplify report generation in the event of a sys-
tem fault.
Several options are available for communication. A faceplate RS232 port can be used to connect to a computer for the pro-
gramming of settings and the monitoring of actual values. The RS232 port has a fixed baud rate of 19.2 kbps. The rear
RS485 port allows independent access by operating and engineering staff. It can be connected to system computers with
baud rates up to 115.2 kbps. All serial ports use the Modbus RTU protocol. The 100Base-FX Ethernet interface provides
fast, reliable communications in noisy environments. The Ethernet port supports IEC 61850, IEC 61850-90-5, Modbus/TCP,
and TFTP protocols, PTP (according to IEEE Std. 1588-2008 or IEC 61588), and allows access to the relay via any stan-
dard web browser (D60 web pages). The IEC 60870-5-104 protocol is supported on the Ethernet port, and DNP 3.0 and
IEC 60870-5-104 cannot be enabled at the same time. The Ethernet port also supports the Parallel Redundancy Protocol
(PRP) of IEC 62439-3 (clause 4, 2012) when purchased as a CPU module option.
The D60 IEDs use flash memory technology which allows field upgrading as new features are added. The following single
line diagram illustrates the relay functionality using ANSI (American National Standards Institute) device numbers.

2.1 INTRODUCTION 2 PRODUCT DESCRIPTION
Table 2–1: DEVICE NUMBERS AND FUNCTIONS

DEVICE FUNCTION DEVICE FUNCTION
NUMBER NUMBER
21G Ground distance 51P Phase time overcurrent
21P Phase distance 51_2 Negative-sequence time overcurrent
25 Synchrocheck 52 AC circuit breaker
2 27P Phase undervoltage 59C Compensated overvoltage
27X Auxiliary undervoltage 59N Neutral overvoltage
32N Wattmetric zero-sequence directional 59P Phase overvoltage
50BF Breaker failure 59X Auxiliary overvoltage
50DD Current disturbance detector 59_2 Negative-sequence overvoltage
50G Ground instantaneous overcurrent 67N Neutral directional overcurrent
50N Neutral instantaneous overcurrent 67P Phase directional overcurrent
50P Phase instantaneous overcurrent 67_2 Negative-sequence directional overcurrent
50_2 Negative-sequence instantaneous overcurrent 68 Power swing blocking
51G Ground time overcurrent 78 Out-of-step tripping
51N Neutral time overcurrent 79 Automatic recloser

&ORVH 7ULS
0RQLWRULQJ
; ;

3 B 3 B %) 3 3 B 1 1 1 *
'' & 1*

'DWDIURPWRUHPRWHHQG 3LORW 7UDQVGXFHU

)OH[(OHPHQW70 0HWHULQJ LQSXWV
YLDFRPPXQLFDWLRQV VFKHPHV
3
3
* *

1
'/LQH'LVWDQFH3URWHFWLRQ6\VWHP
$*&'5
Figure 2–1: SINGLE LINE DIAGRAM

Table 2–2: OTHER DEVICE FUNCTIONS

FUNCTION FUNCTION FUNCTION
Breaker arcing current (I2t) Fault locator Time synchronization over IRIG-B or
IEEE 1588
Breaker control FlexElements™ (8) Time synchronization over SNTP
Breaker flashover FlexLogic equations Transducer inputs and outputs
Contact inputs (up to 96) IEC 61850 communications (optional) Trip bus 2
Contact outputs (up to 64) Line pickup User-definable displays
Control pushbuttons Load encroachment User-programmable LEDs
CyberSentry™ security Metering: current, energy, frequency, User-programmable pushbuttons
power, power factor, voltage
Data logger Modbus user map User-programmable self-tests
Digital counters (8) Non-volatile latches Virtual inputs (64)
Digital elements (48) Non-volatile selector switch Virtual outputs (96)
Direct inputs and outputs (32) Open pole detector VT fuse failure
Disconnect switches (16) Oscillography
DNP 3.0 or IEC 60870-5-104 Comms Pilot schemes
Event recorder Setting groups (6)
Fault detector and fault report Synchrophasors
2.1.2 SECURITY
The following security features are available:

• Password security — Basic security present in the default offering of the product
• EnerVista security — Role-based access to various EnerVista software screens and configuration elements. The fea-
ture is available in the default offering of the product and only in the EnerVista software.
• CyberSentry security — Advanced security options available as a software option. When purchased, the options are
automatically enabled, and the default Password security and EnerVista security are disabled.
a) ENERVISTA SECURITY
The EnerVista security management system is a role-based access control (RBAC) system that allows an administrator to
manage the privileges of multiple users. This allows for access control of UR devices by multiple personnel within a substa-
tion and conforms to the principles of RBAC as defined in ANSI INCITS 359-2004. The EnerVista security management
system is disabled by default to allow the administrator direct access to the EnerVista software after installation. It is recom-
mended that security be enabled before placing the device in service.
Basic password or enhanced CyberSentry security applies, depending on purchase.
b) PASSWORD SECURITY
Password security is a basic security feature present in the default offering of the product.
Two levels of password security are provided: command and setting.
The following operations are under command password supervision:
• Operating the breakers via faceplate keypad
• Changing the state of virtual inputs
• Clearing the event records
• Clearing the oscillography records
• Clearing fault reports
• Changing the date and time
• Clearing the breaker arcing current

• Clearing the data logger

• Clearing the user-programmable pushbutton states
The following operations are under setting password supervision:
• Changing any setting
• Test mode operation
2 The command and setting passwords are defaulted to “0” when the relay is shipped from the factory. When a password is
set to “0”, the password security feature is disabled. As shown in the figures, the window indicates when the password is at
the default and when the password has been set.
Figure 2–2: WINDOW INDICATES DEFAULT PASSWORD (LEFT) AND PASSWORD SET (RIGHT)
The D60 supports password entry from a local or remote connection. Local access is defined as any access to settings or
commands via the faceplate interface. This includes both keypad entry and the through the faceplate RS232 port. Remote
access is defined as any access to settings or commands via any rear communications port. This includes both Ethernet
and RS485 connections. Any changes to the local or remote passwords enables this functionality.
When entering a settings or command password via EnerVista or any serial interface, the user must enter the correspond-
ing connection password. If the connection is to the back of the D60, the remote password must be used. If the connection
is to the RS232 port of the faceplate, the local password applies.
Events are logged in the Event Recorder. The FlexLogic operands and events are updated every five seconds.
c) CYBERSENTRY SECURITY
CyberSentry Embedded Security is a software option that provides advanced security services. When this option is pur-
chased, the basic password security is disabled automatically.
CyberSentry provides security through the following features:
• An Authentication, Authorization, Accounting (AAA) Remote Authentication Dial-In User Service (RADIUS) client that
is centrally managed, enables user attribution, provides accounting of all user activities, and uses secure standards-
based strong cryptography for authentication and credential protection.
• A Role-Based Access Control (RBAC) system that provides a permission model that allows access to UR device oper-
ations and configurations based on specific roles and individual user accounts configured on the AAA server (that is,
Administrator, Supervisor, Engineer, Operator, Observer).
• Security event reporting through the Syslog protocol for supporting Security Information Event Management (SIEM)
systems for centralized cybersecurity monitoring.
• Strong encryption of all access and configuration network messages between the EnerVista software and UR devices
using the Secure Shell (SSH) protocol, the Advanced Encryption Standard (AES), and 128-bit keys in Galois Counter
Mode (GCM) as specified in the U.S. National Security Agency Suite B extension for SSH and approved by the
National Institute of Standards and Technology (NIST) FIPS-140-2 standards for cryptographic systems.

Example: Administrative functions can be segmented away from common operator functions, or engineering type
access, all of which are defined by separate roles, as shown in the following figure, so that access of UR devices by multi-
ple personnel within a substation is allowed. Permission for each role are outlined in the next section.
Figure 2–3: CYBERSENTRY USER ROLES
There are two types of authentication supported by CyberSentry that can be used to access the UR device:
• Device Authentication (local UR device authenticates)
• Server Authentication (RADIUS server authenticates)
The EnerVista software allows access to functionality that is determined by the user role, which comes either from the local
UR device or RADIUS server.
The EnerVista software has a device authentication option on the login screen for accessing the UR device. When the
"Device" button is selected, the UR uses its local authentication database and not the RADIUS server to authenticate the
user. In this case, it uses its built-in roles (Administrator, Engineer, Supervisor, Observer, Operator) as login names and the
associated passwords are stored on the UR device. As such, when using the local accounts, access is not user-attribut-
able.
In cases where user attributable access is required especially to facilitate auditable processes for compliance reasons, use
RADIUS authentication only.
When the "Server" Authentication Type option is selected, the UR uses the RADIUS server and not its local authentication
database to authenticate the user.
No password or security information are displayed in plain text by the EnerVista software or UR device, nor are they ever
transmitted without cryptographic protection.
CYBERSENTRY USER ROLES
CyberSentry user roles (Administrator, Engineer, Operator, Supervisor, Observer) limit the levels of access to various UR
device functions. This means that the EnerVista software allows for access to functionality based on the user’s logged in
role.
Example: Observer cannot write any settings.
The table lists the roles that are supported and their corresponding capabilities.
Table 2–3: PERMISSIONS BY USER ROLE FOR CYBERSENTRY
Roles Administrator Engineer Operator Supervisor Observer

Complete access Complete access Command Authorizes Default role
except for menu writing
CyberSentry
Security
Device Definition R R R R R
Settings
|------------ Product Setup
|--------------- Security (CyberSentry) RW R R R R
|--------------- Supervisory see table notes R R see table notes R
|--------------- Display Properties RW RW R R R


Clear relay records
|--------------- (settings) RW RW R R R
|--------------- Communications RW RW R R R
|--------------- Modbus user map RW RW R R R
|--------------- Real Time Clock RW RW R R R
2 |--------------- Oscillography
|--------------- Data Logger
RW
RW
RW
RW
R
R
R
R
R
R
|--------------- Demand RW RW R R R
User Programmable
|--------------- LEDs RW RW R R R
User Programmable
|--------------- self test RW RW R R R
|--------------- Control Pushbuttons RW RW R R R
User programmable
|--------------- Pushbuttons RW RW R R R
|--------------- Flex states RW RW R R R
User definable dis-
|--------------- plays RW RW R R R
|--------------- Direct I/O RW RW R R R
|--------------- Tele-protection RW RW R R R
|--------------- Installation RW RW R R R
|------------ System Setup RW RW R R R
|------------ FlexLogic RW RW R R R
|------------ Grouped Elements RW RW R R R
|------------ Control Elements RW RW R R R
|------------ Inputs / Outputs RW RW R R R
|--------------- Contact Input RW RW R R R
Contact Input thresh-
|--------------- old RW RW R R R
|--------------- Virtual Inputs RW RW R R R
|--------------- Contact Output RW RW R R R
|--------------- Virtual Output RW RW R R R
|--------------- Remote Devices RW RW R R R
|--------------- Remote Inputs RW RW R R R
|--------------- Remote DPS input RW RW R R R
Remote Output DNA
|--------------- Bit Pair RW RW R R R
Remote Output user
|--------------- Bit Pair RW RW R R R
|--------------- Resetting RW RW R R R
|--------------- Direct Inputs RW RW R R R
|--------------- Direct Outputs RW RW R R R
|--------------- Teleprotection RW RW R R R
|--------------- Direct Analogs RW RW R R R
|--------------- Direct Integers RW RW R R R
IEC61850 GOOSE
|--------------- Analogs RW RW R R R
IEC61850 GOOSE
|--------------- Integers RW RW R R R
|------------ Transducer I/O RW RW R R R
|------------ Testing RW RW R R R


|------------ Front Panel Labels Designer NA NA NA NA NA
|------------ Protection Summary NA NA NA NA NA
Commands RW RW RW R R
|------------ Virtual Inputs RW RW RW R R
|------------ Clear Records RW RW RW R R
|------------ Set date and time RW RW RW R R 2
User Displays R R R R R
Targets R R R R R
Actual Values R R R R R
|------------ Front Panel Labels Designer R R R R R
|------------ Status R R R R R
|------------ Metereing R R R R R
|------------ Transducer I/O R R R R R
|------------ Records R R R R R
|------------ Product Info R R R R R
Maintenance RW RW R R R
|------------ Modbus Analyzer NA NA NA NA NA
|------------ Change Front Panel RW RW RW R R
|------------ Update Firmware Yes No No No No
|------------ Retrieve File Yes No No No No
Table Notes:
1. RW = read and write access
2. R = read access
3. Supervisor = RW (default), Administrator = R (default), Administrator = RW (only if Supervisor role is disabled)
4. NA = the permission is not enforced by CyberSentry Security
CYBERSENTRY SERVER AUTHENTICATION
The UR has been designed to automatically direct authentication requests based on user names. In this respect, local
account names on the UR are considered as reserved, and not used on a RADIUS server.
The UR automatically detects whether an authentication request is to be handled remotely or locally. As there are only five
local accounts possible on the UR, if the user ID credential does not match one of the five local accounts, the UR automat-
ically forwards the request to a RADIUS server when one is provided.
If a RADIUS server is provided, but is unreachable over the network, server authentication requests are denied. In this situ-
ation, use local UR accounts to gain access to the UR system.
2.1.3 ORDERING
a) OVERVIEW
The D60 is available as a 19-inch rack horizontal mount or reduced-size (¾) vertical unit and consists of the following mod-
ules: power supply, CPU, CT/VT, digital input and output, transducer input and output, and inter-relay communications.
Each of these modules can be supplied in a number of configurations specified at the time of ordering. The information
required to completely specify the relay is provided in the following tables (see chapter 3 for full details of relay modules).
Order codes are subject to change without notice. See the ordering page at
http://www.gedigitalenergy.com/multilin/order.htm for the latest options.
NOTE
The order code structure is dependent on the mounting option (horizontal or vertical) and the type of CT/VT modules
(enhanced diagnostic CT/VT modules or HardFiberTM process bus modules). The order code options are described in the
following sub-sections.

b) ORDER CODES WITH ENHANCED CT/VT MODULES

The order codes for the horizontal mount units are shown below.
Table 2–4: D60 ORDER CODES FOR HORIZONTAL UNITS (SHEET 1 OF 2)

D60 - * ** - * * * - F ** - H ** - M ** - P ** - U ** - W/X ** Full Size Horizontal Mount
BASE UNIT D60 | | | | | | | | | | | Base Unit
CPU T | | | | | | | | | | RS485 and Three Multi-mode fiber 100Base-FX (SFP with LC)
U | | | | | | | | | | RS485 and Two Multi-mode fiber 100Base-FX (SFP with LC), One 10/100Base-T (SFP with RJ45)
V | | | | | | | | | | RS485 and Three 10/100Base-T (SFP with RJ45)
2
SOFTWARE 00 | | | | | | | | | No software options
02 | | | | | | | | | Breaker-and-a-half software
03 | | | | | | | | | IEC 61850 communications
05 | | | | | | | | | Breaker-and-a-half software and IEC 61850 communications
06 | | | | | | | | | Phasor measurement unit (PMU)
07 | | | | | | | | | IEC 61850 communications and phasor measurement unit (PMU)
08 | | | | | | | | | Breaker-and-a-Half and phasor measurement unit (PMU)
09 | | | | | | | | | Breaker-and-a-Half, IEC 61850 communications, and phasor measurement unit (PMU)
A0 | | | | | | | | | CyberSentry Lvl 1
A2 | | | | | | | | | CyberSentry Lvl 1 and Breaker-and-a-half
A3 | | | | | | | | | CyberSentry Lvl 1 and IEC 61850
A5 | | | | | | | | | CyberSentry Lvl 1 and IEC 61850 and Breaker-and-a-half
A6 | | | | | | | | | CyberSentry Lvl 1 and phasor measurement unit (PMU)
A7 | | | | | | | | | CyberSentry Lvl 1 and IEC 61850 and phasor measurement unit (PMU)
A8 | | | | | | | | | CyberSentry Lvl 1 and phasor measurement unit (PMU) and Breaker-and-a-half
A9 | | | | | | | | | CyberSentry Lvl 1 and IEC 61850 and phasor measurement unit (PMU) and Breaker-and-a-half
B0 | | | | | | | | | IEEE 1588
B2 | | | | | | | | | IEEE 1588 and Breaker-and-a-half
B3 | | | | | | | | | IEEE 1588 and IEC 61850
B5 | | | | | | | | | IEEE 1588 and IEC 61850 and Breaker-and-a-half
B6 | | | | | | | | | IEEE 1588 and phasor measurement unit (PMU)
B7 | | | | | | | | | IEEE 1588 and IEC 61850 and phasor measurement unit (PMU)
B8 | | | | | | | | | IEEE 1588 and phasor measurement unit (PMU) and Breaker-and-a-half
B9 | | | | | | | | | IEEE 1588 and IEC 61850 and phasor measurement unit (PMU) and Breaker-and-a-half
C0 | | | | | | | | | Parallel Redundancy Protocol (PRP)
C2 | | | | | | | | | PRP and Breaker-and-a-half
C3 | | | | | | | | | PRP and IEC 61850
C5 | | | | | | | | | PRP, IEC 61850, and Breaker-and-a-half
C6 | | | | | | | | | PRP and PMU
C7 | | | | | | | | | PRP, IEC 61850, and PMU
C8 | | | | | | | | | PRP, Breaker-and-a-half, and PMU
C9 | | | | | | | | | PRP, IEC 61850, Breaker-and-a-half, and PMU
D0 | | | | | | | | | IEEE 1588 and CyberSentry Lvl 1
D2 | | | | | | | | | IEEE 1588 and CyberSentry Lvl 1 and IEC 61850
D6 | | | | | | | | | IEEE 1588 and CyberSentry Lvl 1 and phasor measurement unit (PMU)
D7 | | | | | | | | | IEEE 1588 and CyberSentry Lvl 1 and IEC 61850 and phasor measurement unit (PMU)
D9 | | | | | | | | | IEEE 1588 and CyberSentry Lvl 1 and IEC 61850 + phasor measurement unit (PMU) + Breaker-and-a-half
E0 | | | | | | | | | IEEE 1588 and PRP
E2 | | | | | | | | | IEEE 1588, PRP, and Breaker-and-a-half
E3 | | | | | | | | | IEEE 1588, PRP, and IEC 61850
E5 | | | | | | | | | IEEE 1588, PRP, IEC 61850, and Breaker-and-a-half
E6 | | | | | | | | | IEEE 1588, PRP, and PMU
E7 | | | | | | | | | IEEE 1588, PRP, IEC 61850, and PMU
E8 | | | | | | | | | IEEE 1588, PRP, Breaker-and-a-half, and PMU
E9 | | | | | | | | | IEEE 1588, PRP, IEC 61850, Breaker-and-a-half, and PMU
F0 | | | | | | | | | PRP and CyberSentry Lvl 1
F2 | | | | | | | | | PRP, CyberSentry Lvl 1, and Breaker-and-a-half
F3 | | | | | | | | | PRP, CyberSentry Lvl 1, and IEC 61850
F5 | | | | | | | | | PRP CyberSentry Lvl 1, IEC 61850, and Breaker-and-a-half
F6 | | | | | | | | | PRP, CyberSentry Lvl 1, and PMU
F7 | | | | | | | | | PRP, CyberSentry Lvl 1, IEC 61850, and PMU
F8 | | | | | | | | | PRP, CyberSentry Lvl 1, Breaker-and-a-half, and PMU
F9 | | | | | | | | | PRP, CyberSentry Lvl 1, IEC 61850, Breaker-and-a-half, and PMU
G0 | | | | | | | | | IEEE 1588, PRP, and CyberSentry Lvl 1
G2 | | | | | | | | | IEEE 1588, PRP, CyberSentry Lvl 1, Breaker-and-a-half
G3 | | | | | | | | | IEEE 1588, PRP, CyberSentry Lvl 1, and IEC 61850
G5 | | | | | | | | | IEEE 1588, PRP, CyberSentry Lvl 1, IEC 61850, and Breaker-and-a-half
G6 | | | | | | | | | IEEE 1588, PRP, CyberSentry Lvl 1, and PMU
G7 | | | | | | | | | IEEE 1588, PRP, CyberSentry Lvl 1, IEC 61850, and PMU
G8 | | | | | | | | | IEEE 1588, PRP, CyberSentry Lvl 1, Breaker-and-a-half, and PMU
G9 | | | | | | | | | IEEE 1588, PRP, CyberSentry Lvl 1, IEC 61850, Breaker-and-a-half, and PMU

Table 2–4: D60 ORDER CODES FOR HORIZONTAL UNITS (SHEET 2 OF 2)

MOUNT/COATING H | | | | | | | | Horizontal (19” rack)
A | | | | | | | | Horizontal (19” rack) with harsh environmental coating
FACEPLATE/ DISPLAY C | | | | | | | English display
D | | | | | | | French display
R | | | | | | | Russian display
A | | | | | | | Chinese display
P | | | | | | | English display with 4 small and 12 large programmable pushbuttons
G | | | | | | | French display with 4 small and 12 large programmable pushbuttons
S | | | | | | | Russian display with 4 small and 12 large programmable pushbuttons
B | | | | | | | Chinese display with 4 small and 12 large programmable pushbuttons
K | | | | | | | Enhanced front panel with English display
M | | | | | | | Enhanced front panel with French display
Q
U
L
N
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Enhanced front panel with Russian display
Enhanced front panel with Chinese display
Enhanced front panel with English display and user-programmable pushbuttons
Enhanced front panel with French display and user-programmable pushbuttons
2
T | | | | | | | Enhanced front panel with Russian display and user-programmable pushbuttons
V | | | | | | | Enhanced front panel with Chinese display and user-programmable pushbuttons
W | | | | | | | Enhanced front panel with Turkish display
Y | | | | | | | Enhanced front panel with Turkish display and user-programmable pushbuttons
POWER SUPPLY H | | | | | | 125 / 250 V AC/DC power supply
(redundant supply must H | | | | | RH 125 / 250 V AC/DC with redundant 125 / 250 V AC/DC power supply
be same type as main supply) L | | | | | | 24 to 48 V (DC only) power supply
L | | | | | RL 24 to 48 V (DC only) with redundant 24 to 48 V DC power supply
ENHANCED DIAGNOSTICS CT/VT DSP 8L | 8L | | | Standard 4CT/4VT with enhanced diagnostics
(requires all DSP to be enhanced diagnostic) 8M | 8M | | | Sensitive Ground 4CT/4VT with enhanced diagnostics
DIGITAL INPUTS/OUTPUTS XX XX XX XX XX No Module
4A 4A 4A 4A 4A 4 Solid-State (no monitoring) MOSFET outputs
4B 4B 4B 4B 4B 4 Solid-State (voltage with optional current) MOSFET outputs
4C 4C 4C 4C 4C 4 Solid-State (current with optional voltage) MOSFET outputs
4D 4D 4D 4D 4D 16 digital inputs with Auto-Burnishing
4L 4L 4L 4L 4L 14 Form-A (no monitoring) Latching outputs
67 67 67 67 67 8 Form-A (no monitoring) outputs
6A 6A 6A 6A 6A 2 Form-A (voltage with optional current) and 2 Form-C outputs, 8 digital inputs
6B 6B 6B 6B 6B 2 Form-A (voltage with optional current) and 4 Form-C outputs, 4 digital inputs
6C 6C 6C 6C 6C 8 Form-C outputs
6D 6D 6D 6D 6D 16 digital inputs
6E 6E 6E 6E 6E 4 Form-C outputs, 8 digital inputs
6F 6F 6F 6F 6F 8 Fast Form-C outputs
6G 6G 6G 6G 6G 4 Form-A (voltage with optional current) outputs, 8 digital inputs
6H 6H 6H 6H 6H 6 Form-A (voltage with optional current) outputs, 4 digital inputs
6K 6K 6K 6K 6K 4 Form-C and 4 Fast Form-C outputs
6L 6L 6L 6L 6L 2 Form-A (current with optional voltage) and 2 Form-C outputs, 8 digital inputs
6M 6M 6M 6M 6M 2 Form-A (current with optional voltage) and 4 Form-C outputs, 4 digital inputs
6N 6N 6N 6N 6N 4 Form-A (current with optional voltage) outputs, 8 digital inputs
6P 6P 6P 6P 6P 6 Form-A (current with optional voltage) outputs, 4 digital inputs
6R 6R 6R 6R 6R 2 Form-A (no monitoring) and 2 Form-C outputs, 8 digital inputs
6S 6S 6S 6S 6S 2 Form-A (no monitoring) and 4 Form-C outputs, 4 digital inputs
6T 6T 6T 6T 6T 4 Form-A (no monitoring) outputs, 8 digital inputs
6U 6U 6U 6U 6U 6 Form-A (no monitoring) outputs, 4 digital inputs
6V 6V 6V 6V 6V 2 Form-A outputs, 1 Form-C output, 2 Form-A (no monitoring) latching outputs, 8 digital inputs
TRANSDUCER 5A 5A 5A 5A 5A 4 dcmA inputs, 4 dcmA outputs (only one 5A module is allowed)
INPUTS/OUTPUTS 5C 5C 5C 5C 5C 8 RTD inputs
(select a maximum of 3 per unit) 5D 5D 5D 5D 5D 4 RTD inputs, 4 dcmA outputs (only one 5D module is allowed)
5E 5E 5E 5E 5E 4 RTD inputs, 4 dcmA inputs
5F 5F 5F 5F 5F 8 dcmA inputs
INTER-RELAY 2A C37.94SM, 1300nm single-mode, ELED, 1 channel single-mode
COMMUNICATIONS 2B C37.94SM, 1300nm single-mode, ELED, 2 channel single-mode
(select a maximum of 1 per unit) 2E Bi-phase, single channel
2F Bi-phase, dual channel
2G IEEE C37.94, 820 nm, 128 kbps, multimode, LED, 1 Channel
2H IEEE C37.94, 820 nm, 128 kbps, multimode, LED, 2 Channels
72 1550 nm, single-mode, LASER, 1 Channel
74 Channel 1 - RS422; Channel 2 - 1550 nm, single-mode, LASER
75 Channel 1 - G.703; Channel 2 - 1550 nm, Single-mode LASER
76 IEEE C37.94, 820 nm, 64 kbps, multimode, LED, 1 Channel
77 IEEE C37.94, 820 nm, 64 kbps, multimode, LED, 2 Channels
7A 820 nm, multi-mode, LED, 1 Channel
7B 1300 nm, multi-mode, LED, 1 Channel
7C 1300 nm, single-mode, ELED, 1 Channel
7D 1300 nm, single-mode, LASER, 1 Channel
7E Channel 1 - G.703; Channel 2 - 820 nm, multi-mode
7F Channel 1 - G.703; Channel 2 - 1300 nm, multi-mode
7G Channel 1 - G.703; Channel 2 - 1300 nm, single-mode ELED
7H 820 nm, multi-mode, LED, 2 Channels
7I 1300 nm, multi-mode, LED, 2 Channels
7J 1300 nm, single-mode, ELED, 2 Channels
7K 1300 nm, single-mode, LASER, 2 Channels
7L Channel 1 - RS422; Channel 2 - 820 nm, multi-mode, LED
7M Channel 1 - RS422; Channel 2 - 1300 nm, multi-mode, LED
7N Channel 1 - RS422; Channel 2 - 1300 nm, single-mode, ELED
7P Channel 1 - RS422; Channel 2 - 1300 nm, single-mode, LASER
7Q Channel 1 - G.703; Channel 2 - 1300 nm, single-mode LASER
7R G.703, 1 Channel
7S G.703, 2 Channels
7T RS422, 1 Channel
7W RS422, 2 Channels
The order codes for the reduced size vertical mount units are shown below.
Table 2–5: D60 ORDER CODES FOR REDUCED SIZE VERTICAL UNITS
D60 - * ** - * * * - F ** - H ** - M ** - P/R ** Reduced Size Vertical Mount (see note regarding P/R slot below)
BASE UNIT D60 | | | | | | | | | Base Unit
CPU T | | | | | | | | RS485 and Three Multi-mode fiber 100Base-FX (SFP with LC)
U | | | | | | | | RS485 and Two Multi-mode fiber 100Base-FX (SFP with LC), One 10/100Base-T (SFP with RJ45)
V | | | | | | | | RS485 and Three 10/100Base-T (SFP with RJ45)
SOFTWARE 00 | | | | | | | No software options
02 | | | | | | | Breaker-and-a-half software
03 | | | | | | | IEC 61850 communications
05 | | | | | | | Breaker-and-a-half software and IEC 61850 communications
06 | | | | | | | Phasor measurement unit (PMU)
07 | | | | | | | IEC 61850 communications and phasor measurement unit (PMU)
08 | | | | | | | Breaker-and-a-Half and phasor measurement unit (PMU)
09 | | | | | | | Breaker-and-a-Half, IEC 61850 communications, and phasor measurement unit (PMU)
A0 | | | | | | | CyberSentry Lvl 1
A2 | | | | | | | CyberSentry Lvl 1 and Breaker-and-a-half
A3 | | | | | | | CyberSentry Lvl 1 and IEC 61850
A5 | | | | | | | CyberSentry Lvl 1 and IEC 61850 and Breaker-and-a-half
A6 | | | | | | | CyberSentry Lvl 1 and phasor measurement unit (PMU)
A7 | | | | | | | CyberSentry Lvl 1 and IEC 61850 and phasor measurement unit (PMU)
A8 | | | | | | | CyberSentry Lvl 1 and phasor measurement unit (PMU) and Breaker-and-a-half
A9 | | | | | | | CyberSentry Lvl 1 and IEC 61850 and phasor measurement unit (PMU) and Breaker-and-a-half
B0 | | | | | | | IEEE 1588
B2 | | | | | | | IEEE 1588 and Breaker-and-a-half
B3 | | | | | | | IEEE 1588 and IEC 61850
B5 | | | | | | | IEEE 1588 and IEC 61850 and Breaker-and-a-half
B6 | | | | | | | IEEE 1588 and phasor measurement unit (PMU)
B7 | | | | | | | IEEE 1588 and IEC 61850 and phasor measurement unit (PMU)
B8 | | | | | | | IEEE 1588 and phasor measurement unit (PMU) and Breaker-and-a-half
B9 | | | | | | | IEEE 1588 and IEC 61850 and phasor measurement unit (PMU) and Breaker-and-a-half
C0 | | | | | | | Parallel Redundancy Protocol (PRP)

Table 2–5: D60 ORDER CODES FOR REDUCED SIZE VERTICAL UNITS
C2 | | | | | | | PRP and Breaker-and-a-half
C3 | | | | | | | PRP and IEC 61850
C5 | | | | | | | PRP, IEC 61850, and Breaker-and-a-half
C6 | | | | | | | PRP and PMU
C7 | | | | | | | PRP, IEC 61850, and PMU
C8 | | | | | | | PRP, Breaker-and-a-half, and PMU
C9 | | | | | | | PRP, IEC 61850, Breaker-and-a-half, and PMU
D0 | | | | | | | IEEE 1588 and CyberSentry Lvl 1
D2 | | | | | | | IEEE 1588 and CyberSentry Lvl 1 and IEC 61850
D6 | | | | | | | IEEE 1588 and CyberSentry Lvl 1 and phasor measurement unit (PMU)
D7 | | | | | | | IEEE 1588 and CyberSentry Lvl 1 and IEC 61850 and phasor measurement unit (PMU)
2 D9
E0
E2
E3
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
IEEE 1588 and CyberSentry Lvl 1 and IEC 61850 + phasor measurement unit (PMU) + Breaker-and-a-half
IEEE 1588 and PRP
IEEE 1588, PRP, and Breaker-and-a-half
IEEE 1588, PRP, and IEC 61850
E5 | | | | | | | IEEE 1588, PRP, IEC 61850, and Breaker-and-a-half
E6 | | | | | | | IEEE 1588, PRP, and PMU
E7 | | | | | | | IEEE 1588, PRP, IEC 61850, and PMU
E8 | | | | | | | IEEE 1588, PRP, Breaker-and-a-half, and PMU
E9 | | | | | | | IEEE 1588, PRP, IEC 61850, Breaker-and-a-half, and PMU
F0 | | | | | | | PRP and CyberSentry Lvl 1
F2 | | | | | | | PRP, CyberSentry Lvl 1, and Breaker-and-a-half
F3 | | | | | | | PRP, CyberSentry Lvl 1, and IEC 61850
F5 | | | | | | | PRP CyberSentry Lvl 1, IEC 61850, and Breaker-and-a-half
F6 | | | | | | | PRP, CyberSentry Lvl 1, and PMU
F7 | | | | | | | PRP, CyberSentry Lvl 1, IEC 61850, and PMU
F8 | | | | | | | PRP, CyberSentry Lvl 1, Breaker-and-a-half, and PMU
F9 | | | | | | | PRP, CyberSentry Lvl 1, IEC 61850, Breaker-and-a-half, and PMU
G0 | | | | | | | IEEE 1588, PRP, and CyberSentry Lvl 1
G2 | | | | | | | IEEE 1588, PRP, CyberSentry Lvl 1, Breaker-and-a-half
G3 | | | | | | | IEEE 1588, PRP, CyberSentry Lvl 1, and IEC 61850
G5 | | | | | | | IEEE 1588, PRP, CyberSentry Lvl 1, IEC 61850, and Breaker-and-a-half
G6 | | | | | | | IEEE 1588, PRP, CyberSentry Lvl 1, and PMU
G7 | | | | | | | IEEE 1588, PRP, CyberSentry Lvl 1, IEC 61850, and PMU
G8 | | | | | | | IEEE 1588, PRP, CyberSentry Lvl 1, Breaker-and-a-half, and PMU
G9 | | | | | | | IEEE 1588, PRP, CyberSentry Lvl 1, IEC 61850, Breaker-and-a-half, and PMU
MOUNT/COATING V | | | | | | Vertical (3/4 rack)
B | | | | | | Vertical (3/4 rack) with harsh environmental coating
FACEPLATE/ DISPLAY F | | | | | English display
D | | | | | French display
R | | | | | Russian display
A | | | | | Chinese display
K | | | | | Enhanced front panel with English display
M | | | | | Enhanced front panel with French display
Q | | | | | Enhanced front panel with Russian display
U | | | | | Enhanced front panel with Chinese display
L | | | | | Enhanced front panel with English display and user-programmable pushbuttons
N | | | | | Enhanced front panel with French display and user-programmable pushbuttons
T | | | | | Enhanced front panel with Russian display and user-programmable pushbuttons
V | | | | | Enhanced front panel with Chinese display and user-programmable pushbuttons
W | | | | | Enhanced front panel with Turkish display
Y | | | | | Enhanced front panel with Turkish display and user-programmable pushbuttons
POWER SUPPLY H | | | | 125 / 250 V AC/DC power supply
L | | | | 24 to 48 V (DC only) power supply
ENHANCED DIAGNOSTICS CT/VT DSP 8L | 8L | Standard 4CT/4VT with enhanced diagnostics
(requires all DSP to be enhanced diagnostic) 8M | 8M | Sensitive Ground 4CT/4VT with enhanced diagnostics
DIGITAL INPUTS/OUTPUTS XX | XX No Module
4A 4A 4A 4 Solid-State (no monitoring) MOSFET outputs
4B 4B 4B 4 Solid-State (voltage with optional current) MOSFET outputs
4C 4C 4C 4 Solid-State (current with optional voltage) MOSFET outputs
4D 4D 4D 16 digital inputs with Auto-Burnishing
4L 4L 4L 14 Form-A (no monitoring) Latching outputs
67 67 67 8 Form-A (no monitoring) outputs
6A 6A 6A 2 Form-A (voltage with optional current) and 2 Form-C outputs, 8 digital inputs
6B 6B 6B 2 Form-A (voltage with optional current) and 4 Form-C outputs, 4 digital inputs
6C 6C 6C 8 Form-C outputs
6D 6D 6D 16 digital inputs
6E 6E 6E 4 Form-C outputs, 8 digital inputs
6F 6F 6F 8 Fast Form-C outputs
6G 6G 6G 4 Form-A (voltage with optional current) outputs, 8 digital inputs
6H 6H 6H 6 Form-A (voltage with optional current) outputs, 4 digital inputs
6K 6K 6K 4 Form-C and 4 Fast Form-C outputs
6L 6L 6L 2 Form-A (current with optional voltage) and 2 Form-C outputs, 8 digital inputs
6M 6M 6M 2 Form-A (current with optional voltage) and 4 Form-C outputs, 4 digital inputs
6N 6N 6N 4 Form-A (current with optional voltage) outputs, 8 digital inputs
6P 6P 6P 6 Form-A (current with optional voltage) outputs, 4 digital inputs
6R 6R 6R 2 Form-A (no monitoring) and 2 Form-C outputs, 8 digital inputs
6S 6S 6S 2 Form-A (no monitoring) and 4 Form-C outputs, 4 digital inputs
6T 6T 6T 4 Form-A (no monitoring) outputs, 8 digital inputs
6U 6U 6U 6 Form-A (no monitoring) outputs, 4 digital inputs
6V 6V 6V 2 Form-A outputs, 1 Form-C output, 2 Form-A (no monitoring) latching outputs, 8 digital inputs
TRANSDUCER 5A 5A 5A 4 dcmA inputs, 4 dcmA outputs (only one 5A module is allowed)
INPUTS/OUTPUTS 5C 5C 5C 8 RTD inputs
(select a maximum of 3 per unit) 5D 5D 5D 4 RTD inputs, 4 dcmA outputs (only one 5D module is allowed)
5E 5E 5E 4 RTD inputs, 4 dcmA inputs
5F 5F 5F 8 dcmA inputs
For the last module, slot P is used for digital and transducer 2F Bi-phase, dual channel
input/output modules; slot R is used for inter-relay
communications modules. 72 1550 nm, single-mode, LASER, 1 Channel
7R G.703, 1 Channel
7T RS422, 1 Channel

c) ORDER CODES WITH PROCESS BUS MODULES

The order codes for the horizontal mount units with the process bus module are shown below.
Table 2–6: D60 ORDER CODES FOR HORIZONTAL UNITS WITH PROCESS BUS (SHEET 1 OF 2)
CPU T | | | | | | | | | | RS485 and Three Multi-mode fiber 100Base-FX (SFP with LC)
U | | | | | | | | | | RS485 and Two Multi-mode fiber 100Base-FX (SFP with LC), One 10/100Base-T (SFP with RJ45)
V | | | | | | | | | | RS485 and Three 10/100Base-T (SFP with RJ45)
2
SOFTWARE 00 | | | | | | | | | No software options
03 | | | | | | | | | IEC 61850 communications
06 | | | | | | | | | Phasor measurement unit (PMU)
07 | | | | | | | | | IEC 61850 communications and phasor measurement unit (PMU)
A0 | | | | | | | | | CyberSentry Lvl 1
A2 | | | | | | | | | CyberSentry Lvl 1 and Breaker-and-a-half
A3 | | | | | | | | | CyberSentry Lvl 1 and IEC 61850
A5 | | | | | | | | | CyberSentry Lvl 1 and IEC 61850 and Breaker-and-a-half
A6 | | | | | | | | | CyberSentry Lvl 1 and phasor measurement unit (PMU)
A7 | | | | | | | | | CyberSentry Lvl 1 and IEC 61850 and phasor measurement unit (PMU)
A8 | | | | | | | | | CyberSentry Lvl 1 and phasor measurement unit (PMU) and Breaker-and-a-half
A9 | | | | | | | | | CyberSentry Lvl 1 and IEC 61850 and phasor measurement unit (PMU) and Breaker-and-a-half
B0 | | | | | | | | | IEEE 1588
B2 | | | | | | | | | IEEE 1588 and Breaker-and-a-half
B3 | | | | | | | | | IEEE 1588 and IEC 61850
B5 | | | | | | | | | IEEE 1588 and IEC 61850 and Breaker-and-a-half
B6 | | | | | | | | | IEEE 1588 and phasor measurement unit (PMU)
B7 | | | | | | | | | IEEE 1588 and IEC 61850 and phasor measurement unit (PMU)
B8 | | | | | | | | | IEEE 1588 and phasor measurement unit (PMU) and Breaker-and-a-half
B9 | | | | | | | | | IEEE 1588 and IEC 61850 and phasor measurement unit (PMU) and Breaker-and-a-half
C0 | | | | | | | | | Parallel Redundancy Protocol (PRP)
C2 | | | | | | | | | PRP and Breaker-and-a-half
C3 | | | | | | | | | PRP and IEC 61850
C5 | | | | | | | | | PRP, IEC 61850, and Breaker-and-a-half
C6 | | | | | | | | | PRP and PMU
C7 | | | | | | | | | PRP, IEC 61850, and PMU
C8 | | | | | | | | | PRP, Breaker-and-a-half, and PMU
C9 | | | | | | | | | PRP, IEC 61850, Breaker-and-a-half, and PMU
D0 | | | | | | | | | IEEE 1588 and CyberSentry Lvl 1
D6 | | | | | | | | | IEEE 1588 and CyberSentry Lvl 1 and phasor measurement unit (PMU)
D9 | | | | | | | | | IEEE 1588 and CyberSentry Lvl 1 and IEC 61850 + phasor measurement unit (PMU) + Breaker-and-a-half
E0 | | | | | | | | | IEEE 1588 and PRP
E2 | | | | | | | | | IEEE 1588, PRP, and Breaker-and-a-half
E3 | | | | | | | | | IEEE 1588, PRP, and IEC 61850
E5 | | | | | | | | | IEEE 1588, PRP, IEC 61850, and Breaker-and-a-half
E6 | | | | | | | | | IEEE 1588, PRP, and PMU
E7 | | | | | | | | | IEEE 1588, PRP, IEC 61850, and PMU
E8 | | | | | | | | | IEEE 1588, PRP, Breaker-and-a-half, and PMU
E9 | | | | | | | | | IEEE 1588, PRP, IEC 61850, Breaker-and-a-half, and PMU
F0 | | | | | | | | | PRP and CyberSentry Lvl 1
F2 | | | | | | | | | PRP, CyberSentry Lvl 1, and Breaker-and-a-half
F3 | | | | | | | | | PRP, CyberSentry Lvl 1, and IEC 61850
F5 | | | | | | | | | PRP CyberSentry Lvl 1, IEC 61850, and Breaker-and-a-half
F6 | | | | | | | | | PRP, CyberSentry Lvl 1, and PMU
F7 | | | | | | | | | PRP, CyberSentry Lvl 1, IEC 61850, and PMU
F8 | | | | | | | | | PRP, CyberSentry Lvl 1, Breaker-and-a-half, and PMU
F9 | | | | | | | | | PRP, CyberSentry Lvl 1, IEC 61850, Breaker-and-a-half, and PMU
G0 | | | | | | | | | IEEE 1588, PRP, and CyberSentry Lvl 1
G2 | | | | | | | | | IEEE 1588, PRP, CyberSentry Lvl 1, Breaker-and-a-half
G3 | | | | | | | | | IEEE 1588, PRP, CyberSentry Lvl 1, and IEC 61850
G5 | | | | | | | | | IEEE 1588, PRP, CyberSentry Lvl 1, IEC 61850, and Breaker-and-a-half
G6 | | | | | | | | | IEEE 1588, PRP, CyberSentry Lvl 1, and PMU
G7 | | | | | | | | | IEEE 1588, PRP, CyberSentry Lvl 1, IEC 61850, and PMU
G8 | | | | | | | | | IEEE 1588, PRP, CyberSentry Lvl 1, Breaker-and-a-half, and PMU
G9 | | | | | | | | | IEEE 1588, PRP, CyberSentry Lvl 1, IEC 61850, Breaker-and-a-half, and PMU
MOUNT/COATING H | | | | | | | | Horizontal (19” rack)
A | | | | | | | | Horizontal (19” rack) with harsh environmental coating
FACEPLATE/ DISPLAY C | | | | | | | English display
D | | | | | | | French display
R | | | | | | | Russian display
A | | | | | | | Chinese display
P | | | | | | | English display with 4 small and 12 large programmable pushbuttons
G | | | | | | | French display with 4 small and 12 large programmable pushbuttons
S | | | | | | | Russian display with 4 small and 12 large programmable pushbuttons
B | | | | | | | Chinese display with 4 small and 12 large programmable pushbuttons
K | | | | | | | Enhanced front panel with English display
M | | | | | | | Enhanced front panel with French display
Q | | | | | | | Enhanced front panel with Russian display
U | | | | | | | Enhanced front panel with Chinese display
L | | | | | | | Enhanced front panel with English display and user-programmable pushbuttons
N | | | | | | | Enhanced front panel with French display and user-programmable pushbuttons
T | | | | | | | Enhanced front panel with Russian display and user-programmable pushbuttons
V | | | | | | | Enhanced front panel with Chinese display and user-programmable pushbuttons
W | | | | | | | Enhanced front panel with Turkish display
Y | | | | | | | Enhanced front panel with Turkish display and user-programmable pushbuttons
POWER SUPPLY H | | | | | | 125 / 250 V AC/DC power supply
(redundant supply must H | | | | | RH 125 / 250 V AC/DC with redundant 125 / 250 V AC/DC power supply
be same type as main supply) L | | | | | | 24 to 48 V (DC only) power supply
L | | | | | RL 24 to 48 V (DC only) with redundant 24 to 48 V DC power supply
PROCESS BUS MODULE | 81 | | | | Eight-port digital process bus module
DIGITAL INPUTS/OUTPUTS XX XX XX XX XX No Module
4A 4A | 4 Solid-State (no monitoring) MOSFET outputs
4B 4B | 4 Solid-State (voltage with optional current) MOSFET outputs
4C 4C | 4 Solid-State (current with optional voltage) MOSFET outputs
4D 4D | 16 digital inputs with Auto-Burnishing
4L 4L | 14 Form-A (no monitoring) Latching outputs
67 67 | 8 Form-A (no monitoring) outputs
6A 6A | 2 Form-A (voltage with optional current) and 2 Form-C outputs, 8 digital inputs
6B 6B | 2 Form-A (voltage with optional current) and 4 Form-C outputs, 4 digital inputs
6C 6C | 8 Form-C outputs
6D 6D | 16 digital inputs
6E 6E | 4 Form-C outputs, 8 digital inputs
6F 6F | 8 Fast Form-C outputs
6G 6G | 4 Form-A (voltage with optional current) outputs, 8 digital inputs
6H 6H | 6 Form-A (voltage with optional current) outputs, 4 digital inputs
6K 6K | 4 Form-C and 4 Fast Form-C outputs
6L 6L | 2 Form-A (current with optional voltage) and 2 Form-C outputs, 8 digital inputs
6M 6M | 2 Form-A (current with optional voltage) and 4 Form-C outputs, 4 digital inputs
6N 6N | 4 Form-A (current with optional voltage) outputs, 8 digital inputs
6P 6P | 6 Form-A (current with optional voltage) outputs, 4 digital inputs
6R 6R | 2 Form-A (no monitoring) and 2 Form-C outputs, 8 digital inputs
6S 6S | 2 Form-A (no monitoring) and 4 Form-C outputs, 4 digital inputs
6T 6T | 4 Form-A (no monitoring) outputs, 8 digital inputs
6U 6U | 6 Form-A (no monitoring) outputs, 4 digital inputs
6V 6V | 2 Form-A outputs, 1 Form-C output, 2 Form-A (no monitoring) latching outputs, 8 digital inputs
2F Bi-phase, dual channel

Table 2–6: D60 ORDER CODES FOR HORIZONTAL UNITS WITH PROCESS BUS (SHEET 2 OF 2)
2 7G
7H
7I
7J
Channel 1 - G.703; Channel 2 - 1300 nm, single-mode ELED
820 nm, multi-mode, LED, 2 Channels
1300 nm, multi-mode, LED, 2 Channels
1300 nm, single-mode, ELED, 2 Channels
7R G.703, 1 Channel
7T RS422, 1 Channel
The order codes for the reduced size vertical mount units with the process bus module are shown below.
Table 2–7: D60 ORDER CODES FOR REDUCED SIZE VERTICAL UNITS WITH PROCESS BUS (SHEET 1 OF 2)
D60 - * ** - * * * - F ** - H ** - M ** - P/R ** Reduced Size Vertical Mount (see note regarding P/R slot below)
BASE UNIT D60 | | | | | | | | | Base Unit
CPU T | | | | | | | | RS485 and Three Multi-mode fiber 100Base-FX (SFP with LC)
U | | | | | | | | RS485 and Two Multi-mode fiber 100Base-FX (SFP with LC), One 10/100Base-T (SFP with RJ45)
V | | | | | | | | RS485 and Three 10/100Base-T (SFP with RJ45)
SOFTWARE 00 | | | | | | | No software options
03 | | | | | | | IEC 61850 communications
06 | | | | | | | Phasor measurement unit (PMU)
07 | | | | | | | IEC 61850 communications and phasor measurement unit (PMU)
A0 | | | | | | | CyberSentry Lvl 1
A2 | | | | | | | CyberSentry Lvl 1 and Breaker-and-a-half
A3 | | | | | | | CyberSentry Lvl 1 and IEC 61850
A5 | | | | | | | CyberSentry Lvl 1 and IEC 61850 and Breaker-and-a-half
A6 | | | | | | | CyberSentry Lvl 1 and phasor measurement unit (PMU)
A7 | | | | | | | CyberSentry Lvl 1 and IEC 61850 and phasor measurement unit (PMU)
A8 | | | | | | | CyberSentry Lvl 1 and phasor measurement unit (PMU) and Breaker-and-a-half
A9 | | | | | | | CyberSentry Lvl 1 and IEC 61850 and phasor measurement unit (PMU) and Breaker-and-a-half
B0 | | | | | | | IEEE 1588
B2 | | | | | | | IEEE 1588 and Breaker-and-a-half
B3 | | | | | | | IEEE 1588 and IEC 61850
B5 | | | | | | | IEEE 1588 and IEC 61850 and Breaker-and-a-half
B6 | | | | | | | IEEE 1588 and phasor measurement unit (PMU)
B7 | | | | | | | IEEE 1588 and IEC 61850 and phasor measurement unit (PMU)
B8 | | | | | | | IEEE 1588 and phasor measurement unit (PMU) and Breaker-and-a-half
B9 | | | | | | | IEEE 1588 and IEC 61850 and phasor measurement unit (PMU) and Breaker-and-a-half
C0 | | | | | | | Parallel Redundancy Protocol (PRP)
C2 | | | | | | | PRP and Breaker-and-a-half
C3 | | | | | | | PRP and IEC 61850
C5 | | | | | | | PRP, IEC 61850, and Breaker-and-a-half
C6 | | | | | | | PRP and PMU
C7 | | | | | | | PRP, IEC 61850, and PMU
C8 | | | | | | | PRP, Breaker-and-a-half, and PMU
C9 | | | | | | | PRP, IEC 61850, Breaker-and-a-half, and PMU
D0 | | | | | | | IEEE 1588 and CyberSentry Lvl 1
D6 | | | | | | | IEEE 1588 and CyberSentry Lvl 1 and phasor measurement unit (PMU)
D9 | | | | | | | IEEE 1588 and CyberSentry Lvl 1 and IEC 61850 + phasor measurement unit (PMU) + Breaker-and-a-half
E0 | | | | | | | IEEE 1588 and PRP
E2 | | | | | | | IEEE 1588, PRP, and Breaker-and-a-half
E3 | | | | | | | IEEE 1588, PRP, and IEC 61850
E5 | | | | | | | IEEE 1588, PRP, IEC 61850, and Breaker-and-a-half
E6 | | | | | | | IEEE 1588, PRP, and PMU
E7 | | | | | | | IEEE 1588, PRP, IEC 61850, and PMU
E8 | | | | | | | IEEE 1588, PRP, Breaker-and-a-half, and PMU
E9 | | | | | | | IEEE 1588, PRP, IEC 61850, Breaker-and-a-half, and PMU
F0 | | | | | | | PRP and CyberSentry Lvl 1
F2 | | | | | | | PRP, CyberSentry Lvl 1, and Breaker-and-a-half
F3 | | | | | | | PRP, CyberSentry Lvl 1, and IEC 61850
F5 | | | | | | | PRP CyberSentry Lvl 1, IEC 61850, and Breaker-and-a-half
F6 | | | | | | | PRP, CyberSentry Lvl 1, and PMU
F7 | | | | | | | PRP, CyberSentry Lvl 1, IEC 61850, and PMU
F8 | | | | | | | PRP, CyberSentry Lvl 1, Breaker-and-a-half, and PMU
F9 | | | | | | | PRP, CyberSentry Lvl 1, IEC 61850, Breaker-and-a-half, and PMU
G0 | | | | | | | IEEE 1588, PRP, and CyberSentry Lvl 1
G2 | | | | | | | IEEE 1588, PRP, CyberSentry Lvl 1, Breaker-and-a-half
G3 | | | | | | | IEEE 1588, PRP, CyberSentry Lvl 1, and IEC 61850
G5 | | | | | | | IEEE 1588, PRP, CyberSentry Lvl 1, IEC 61850, and Breaker-and-a-half
G6 | | | | | | | IEEE 1588, PRP, CyberSentry Lvl 1, and PMU
G7 | | | | | | | IEEE 1588, PRP, CyberSentry Lvl 1, IEC 61850, and PMU
G8 | | | | | | | IEEE 1588, PRP, CyberSentry Lvl 1, Breaker-and-a-half, and PMU
G9 | | | | | | | IEEE 1588, PRP, CyberSentry Lvl 1, IEC 61850, Breaker-and-a-half, and PMU
MOUNT/COATING V | | | | | | Vertical (3/4 rack)
B | | | | | | Vertical (3/4 rack) with harsh environmental coating
FACEPLATE/ DISPLAY F | | | | | English display
D | | | | | French display
R | | | | | Russian display
A | | | | | Chinese display
K | | | | | Enhanced front panel with English display
M | | | | | Enhanced front panel with French display
Q | | | | | Enhanced front panel with Russian display
U | | | | | Enhanced front panel with Chinese display
L | | | | | Enhanced front panel with English display and user-programmable pushbuttons
N | | | | | Enhanced front panel with French display and user-programmable pushbuttons
T | | | | | Enhanced front panel with Russian display and user-programmable pushbuttons
V | | | | | Enhanced front panel with Chinese display and user-programmable pushbuttons
W | | | | | Enhanced front panel with Turkish display
Y | | | | | Enhanced front panel with Turkish display and user-programmable pushbuttons

Table 2–7: D60 ORDER CODES FOR REDUCED SIZE VERTICAL UNITS WITH PROCESS BUS (SHEET 2 OF 2)
POWER SUPPLY H | | | | 125 / 250 V AC/DC power supply
L | | | | 24 to 48 V (DC only) power supply
PROCESS BUS MODULE | 81 | Eight-port digital process bus module
DIGITAL INPUTS/OUTPUTS XX XX XX No Module
4A 4 Solid-State (no monitoring) MOSFET outputs
4B 4 Solid-State (voltage with optional current) MOSFET outputs
4C 4 Solid-State (current with optional voltage) MOSFET outputs
4D 16 digital inputs with Auto-Burnishing
4L 14 Form-A (no monitoring) Latching outputs
67 8 Form-A (no monitoring) outputs
6A 2 Form-A (voltage with optional current) and 2 Form-C outputs, 8 digital inputs
6B 2 Form-A (voltage with optional current) and 4 Form-C outputs, 4 digital inputs
6C 8 Form-C outputs
6D 16 digital inputs
6E
6F
6G
6H
4 Form-C outputs, 8 digital inputs
8 Fast Form-C outputs
4 Form-A (voltage with optional current) outputs, 8 digital inputs
6 Form-A (voltage with optional current) outputs, 4 digital inputs
2
6K 4 Form-C and 4 Fast Form-C outputs
6L 2 Form-A (current with optional voltage) and 2 Form-C outputs, 8 digital inputs
6M 2 Form-A (current with optional voltage) and 4 Form-C outputs, 4 digital inputs
6N 4 Form-A (current with optional voltage) outputs, 8 digital inputs
6P 6 Form-A (current with optional voltage) outputs, 4 digital inputs
6R 2 Form-A (no monitoring) and 2 Form-C outputs, 8 digital inputs
6S 2 Form-A (no monitoring) and 4 Form-C outputs, 4 digital inputs
6T 4 Form-A (no monitoring) outputs, 8 digital inputs
6U 6 Form-A (no monitoring) outputs, 4 digital inputs
6V 2 Form-A outputs, 1 Form-C output, 2 Form-A (no monitoring) latching outputs, 8 digital inputs
For the last module, slot P is used for digital 2F Bi-phase, dual channel
input/output modules; slot R is used for inter-relay
communications modules. 72 1550 nm, single-mode, LASER, 1 Channel
7R G.703, 1 Channel
7T RS422, 1 Channel

2.1.4 REPLACEMENT MODULES
Replacement modules can be ordered separately. When ordering a replacement CPU module or faceplate, provide the
serial number of your existing unit.
Not all replacement modules may be applicable to the D60 relay. Only the modules specified in the order codes are
available as replacement modules.
NOTE
2 Replacement module codes are subject to change without notice. See the ordering page at
http://www.gedigitalenergy.com/multilin/order.htm for the latest D60 ordering options.
NOTE
The replacement module order codes for the horizontal mount units are shown below.
Table 2–8: ORDER CODES FOR REPLACEMENT MODULES, HORIZONTAL UNITS

UR - ** - *
POWER SUPPLY (redundant supply only available in | RH H | Redundant 125 / 250 V AC/DC
horizontal units; must be same type as main supply) | RL H | Redundant 24 to 48 V (DC only)
CPU | T | RS485 with 3 100Base-FX Ethernet, multimode, SFP with LC
| U | RS485 with 1 100Base-T Ethernet, SFP RJ-45 + 2 100Base-FX Ethernet, multimode, SFP with LC
| V | RS485 with 3 100Base-T Ethernet, SFP with RJ-45
FACEPLATE/DISPLAY | 3C | Horizontal faceplate with keypad and English display
| 3D | Horizontal faceplate with keypad and French display
| 3R | Horizontal faceplate with keypad and Russian display
| 3A | Horizontal faceplate with keypad and Chinese display
| 3P | Horizontal faceplate with keypad, user-programmable pushbuttons, and English display
| 3G | Horizontal faceplate with keypad, user-programmable pushbuttons, and French display
| 3S | Horizontal faceplate with keypad, user-programmable pushbuttons, and Russian display
| 3B | Horizontal faceplate with keypad, user-programmable pushbuttons, and Chinese display
| 3K | Enhanced front panel with English display
| 3M | Enhanced front panel with French display
| 3Q | Enhanced front panel with Russian display
| 3U | Enhanced front panel with Chinese display
| 3L | Enhanced front panel with English display and user-programmable pushbuttons
| 3N | Enhanced front panel with French display and user-programmable pushbuttons
| 3T | Enhanced front panel with Russian display and user-programmable pushbuttons
| 3V | Enhanced front panel with Chinese display and user-programmable pushbuttons
DIGITAL INPUTS AND OUTPUTS | 4A | 4 Solid-State (no monitoring) MOSFET outputs
| 4B | 4 Solid-State (voltage with optional current) MOSFET outputs
| 4C | 4 Solid-State (current with optional voltage) MOSFET outputs
| 4D | 16 digital inputs with Auto-Burnishing
| 4L | 14 Form-A (no monitoring) Latching outputs
| 67 | 8 Form-A (no monitoring) outputs
| 6A | 2 Form-A (voltage with optional current) and 2 Form-C outputs, 8 digital inputs
| 6B | 2 Form-A (voltage with optional current) and 4 Form-C outputs, 4 digital inputs
| 6C | 8 Form-C outputs
| 6D | 16 digital inputs
| 6E | 4 Form-C outputs, 8 digital inputs
| 6F | 8 Fast Form-C outputs
| 6G | 4 Form-A (voltage with optional current) outputs, 8 digital inputs
| 6H | 6 Form-A (voltage with optional current) outputs, 4 digital inputs
| 6K | 4 Form-C and 4 Fast Form-C outputs
| 6L | 2 Form-A (current with optional voltage) and 2 Form-C outputs, 8 digital inputs
| 6M | 2 Form-A (current with optional voltage) and 4 Form-C outputs, 4 digital inputs
| 6N | 4 Form-A (current with optional voltage) outputs, 8 digital inputs
| 6P | 6 Form-A (current with optional voltage) outputs, 4 digital inputs
| 6R | 2 Form-A (no monitoring) and 2 Form-C outputs, 8 digital inputs
| 6S | 2 Form-A (no monitoring) and 4 Form-C outputs, 4 digital inputs
| 6T | 4 Form-A (no monitoring) outputs, 8 digital inputs
| 6U | 6 Form-A (no monitoring) outputs, 4 digital inputs
| 6V | 2 Form-A outputs, 1 Form-C output, 2 Form-A (no monitoring) latching outputs, 8 digital inputs
CT/VT MODULES | 8L | Standard 4CT/4VT with enhanced diagnostics
(NOT AVAILABLE FOR THE C30) | 8N | Standard 8CT with enhanced diagnostics
| 8M | Sensitive Ground 4CT/4VT with enhanced diagnostics
| 8R | Sensitive Ground 8CT with enhanced diagnostics
INTER-RELAY COMMUNICATIONS | 2A | C37.94SM, 1300nm single-mode, ELED, 1 channel single-mode
| 2B | C37.94SM, 1300nm single-mode, ELED, 2 channel single-mode
| 2E | Bi-phase, single channel
| 2F | Bi-phase, dual channel
| 2G | IEEE C37.94, 820 nm, 128 kbps, multimode, LED, 1 Channel
| 2H | IEEE C37.94, 820 nm, 128 kbps, multimode, LED, 2 Channels
| 72 | 1550 nm, single-mode, LASER, 1 Channel
| 74 | Channel 1 - RS422; Channel 2 - 1550 nm, single-mode, LASER
| 75 | Channel 1 - G.703; Channel 2 - 1550 nm, Single-mode LASER
| 76 | IEEE C37.94, 820 nm, multimode, LED, 1 Channel
| 77 | IEEE C37.94, 820 nm, multimode, LED, 2 Channels
| 7A | 820 nm, multi-mode, LED, 1 Channel
| 7B | 1300 nm, multi-mode, LED, 1 Channel
| 7C | 1300 nm, single-mode, ELED, 1 Channel
| 7D | 1300 nm, single-mode, LASER, 1 Channel
| 7E | Channel 1 - G.703; Channel 2 - 820 nm, multi-mode
| 7F | Channel 1 - G.703; Channel 2 - 1300 nm, multi-mode
| 7G | Channel 1 - G.703; Channel 2 - 1300 nm, single-mode ELED
| 7H | 820 nm, multi-mode, LED, 2 Channels
| 7I | 1300 nm, multi-mode, LED, 2 Channels
| 7J | 1300 nm, single-mode, ELED, 2 Channels
| 7K | 1300 nm, single-mode, LASER, 2 Channels
| 7L | Channel 1 - RS422; Channel 2 - 820 nm, multi-mode, LED
| 7M | Channel 1 - RS422; Channel 2 - 1300 nm, multi-mode, LED
| 7N | Channel 1 - RS422; Channel 2 - 1300 nm, single-mode, ELED
| 7P | Channel 1 - RS422; Channel 2 - 1300 nm, single-mode, LASER
| 7Q | Channel 1 - G.703; Channel 2 - 1300 nm, single-mode LASER
| 7R | G.703, 1 Channel
| 7S | G.703, 2 Channels
| 7T | RS422, 1 Channel
| 7W | RS422, 2 Channels
TRANSDUCER | 5A | 4 dcmA inputs, 4 dcmA outputs (only one 5A module is allowed)
INPUTS/OUTPUTS | 5C | 8 RTD inputs
| 5D | 4 RTD inputs, 4 dcmA outputs (only one 5D module is allowed)
| 5E | 4 dcmA inputs, 4 RTD inputs
| 5F | 8 dcmA inputs

The replacement module order codes for the reduced-size vertical mount units are shown below.
Table 2–9: ORDER CODES FOR REPLACEMENT MODULES, VERTICAL UNITS

UR - ** - *
POWER SUPPLY | RH V | 125 / 250 V AC/DC
| RL V | 24 to 48 V (DC only)
CPU | T | RS485 with 3 100Base-FX Ethernet, multimode, SFP with LC
| U | RS485 with 1 100Base-T Ethernet, SFP RJ-45 + 2 100Base-FX Ethernet, multimode, SFP with LC
| V | RS485 with 3 100Base-T Ethernet, SFP with RJ-45
FACEPLATE/DISPLAY | 3F | Vertical faceplate with keypad and English display
| 3D | Vertical faceplate with keypad and French display
| 3R | Vertical faceplate with keypad and Russian display
|
|
|
|
3K
3K
3M
3Q
|
|
|
|
Vertical faceplate with keypad and Chinese display
Enhanced front panel with English display
Enhanced front panel with French display
Enhanced front panel with Russian display
2
| 3U | Enhanced front panel with Chinese display
| 3L | Enhanced front panel with English display and user-programmable pushbuttons
| 3N | Enhanced front panel with French display and user-programmable pushbuttons
| 3T | Enhanced front panel with Russian display and user-programmable pushbuttons
| 3V | Enhanced front panel with Chinese display and user-programmable pushbuttons
DIGITAL | 4A | 4 Solid-State (no monitoring) MOSFET outputs
INPUTS/OUTPUTS | 4B | 4 Solid-State (voltage with optional current) MOSFET outputs
| 4C | 4 Solid-State (current with optional voltage) MOSFET outputs
| 4D | 16 digital inputs with Auto-Burnishing
| 4L | 14 Form-A (no monitoring) Latching outputs
| 67 | 8 Form-A (no monitoring) outputs
| 6A | 2 Form-A (voltage with optional current) and 2 Form-C outputs, 8 digital inputs
| 6B | 2 Form-A (voltage with optional current) and 4 Form-C outputs, 4 digital inputs
| 6C | 8 Form-C outputs
| 6D | 16 digital inputs
| 6E | 4 Form-C outputs, 8 digital inputs
| 6F | 8 Fast Form-C outputs
| 6G | 4 Form-A (voltage with optional current) outputs, 8 digital inputs
| 6H | 6 Form-A (voltage with optional current) outputs, 4 digital inputs
| 6K | 4 Form-C and 4 Fast Form-C outputs
| 6L | 2 Form-A (current with optional voltage) and 2 Form-C outputs, 8 digital inputs
| 6M | 2 Form-A (current with optional voltage) and 4 Form-C outputs, 4 digital inputs
| 6N | 4 Form-A (current with optional voltage) outputs, 8 digital inputs
| 6P | 6 Form-A (current with optional voltage) outputs, 4 digital inputs
| 6R | 2 Form-A (no monitoring) and 2 Form-C outputs, 8 digital inputs
| 6S | 2 Form-A (no monitoring) and 4 Form-C outputs, 4 digital inputs
| 6T | 4 Form-A (no monitoring) outputs, 8 digital inputs
| 6U | 6 Form-A (no monitoring) outputs, 4 digital inputs
| 6V | 2 Form-A outputs, 1 Form-C output, 2 Form-A (no monitoring) latching outputs, 8 digital inputs
CT/VT MODULES | 8L | Standard 4CT/4VT with enhanced diagnostics
(NOT AVAILABLE FOR THE C30) | 8N | Standard 8CT with enhanced diagnostics
INTER-RELAY COMMUNICATIONS | 2A | C37.94SM, 1300nm single-mode, ELED, 1 channel single-mode
| 2B | C37.94SM, 1300nm single-mode, ELED, 2 channel single-mode
| 2E | Bi-phase, single channel
| 2F | Bi-phase, dual channel
| 2G | IEEE C37.94, 820 nm, 128 kbps, multimode, LED, 1 Channel
| 2H | IEEE C37.94, 820 nm, 128 kbps, multimode, LED, 2 Channels
| 74 | Channel 1 - RS422; Channel 2 - 1550 nm, single-mode, LASER
| 75 | Channel 1 - G.703; Channel 2 - 1550 nm, Single-mode LASER
| 76 | IEEE C37.94, 820 nm, 64 kbps, multimode, LED, 1 Channel
| 77 | IEEE C37.94, 820 nm, 64 kbps, multimode, LED, 2 Channels
| 7A | 820 nm, multi-mode, LED, 1 Channel
| 7B | 1300 nm, multi-mode, LED, 1 Channel
| 7C | 1300 nm, single-mode, ELED, 1 Channel
| 7D | 1300 nm, single-mode, LASER, 1 Channel
| 7E | Channel 1 - G.703; Channel 2 - 820 nm, multi-mode
| 7F | Channel 1 - G.703; Channel 2 - 1300 nm, multi-mode
| 7G | Channel 1 - G.703; Channel 2 - 1300 nm, single-mode ELED
| 7H | 820 nm, multi-mode, LED, 2 Channels
| 7I | 1300 nm, multi-mode, LED, 2 Channels
| 7J | 1300 nm, single-mode, ELED, 2 Channels
| 7K | 1300 nm, single-mode, LASER, 2 Channels
| 7L | Channel 1 - RS422; Channel 2 - 820 nm, multi-mode, LED
| 7M | Channel 1 - RS422; Channel 2 - 1300 nm, multi-mode, LED
| 7N | Channel 1 - RS422; Channel 2 - 1300 nm, single-mode, ELED
| 7P | Channel 1 - RS422; Channel 2 - 1300 nm, single-mode, LASER
| 7Q | Channel 1 - G.703; Channel 2 - 1300 nm, single-mode LASER
| 7R | G.703, 1 Channel
| 7S | G.703, 2 Channels
| 7T | RS422, 1 Channel
| 7W | RS422, 2 Channels
TRANSDUCER | 5A | 4 dcmA inputs, 4 dcmA outputs (only one 5A module is allowed)
INPUTS/OUTPUTS | 5C | 8 RTD inputs
| 5D | 4 RTD inputs, 4 dcmA outputs (only one 5D module is allowed)
| 5E | 4 dcmA inputs, 4 RTD inputs
| 5F | 8 dcmA inputs

2.2 SPECIFICATIONS 2 PRODUCT DESCRIPTION
2.2SPECIFICATIONSSPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
2.2.1 PROTECTION ELEMENTS
The operating times include the activation time of a trip rated form-A output contact unless otherwise indicated.
FlexLogic operands of a given element are 4 ms faster. Take this into account when using FlexLogic to interconnect
NOTE with other protection or control elements of the relay, building FlexLogic equations, or interfacing with other IEDs or
2 power system devices via communications or different output contacts. If not specified, operate times are given
here for a 60 Hz system at nominal system frequency. Operate times for a 50 Hz system are 1.2 times longer.
PHASE DISTANCE PHASE DISTANCE OPERATING TIME CURVES
Characteristic: mho (memory polarized or offset) or The operating times are response times of a microprocessor part
quad (memory polarized or non-direc- of the relay. See output contacts specifications for estimation of
tional), selectable individually per zone the total response time for a particular application. The operating
Number of zones: 5 times are average times including variables such as fault inception
Directionality: forward, reverse, or non-directional per angle or type of a voltage source (magnetic VTs and CVTs).
zone
Reach (secondary ): 0.02 to 500.00  in steps of 0.01 Phase Element (21P)
Reach accuracy: ±5% including the effect of CVT tran- 30

SIR = 0.1
sients up to an SIR of 30 SIR = 1
25 SIR = 10
Distance: SIR = 20
SIR = 30
Characteristic angle: 30 to 90° in steps of 1
Operating Time [ms]
20
Comparator limit angle: 30 to 90° in steps of 1

15
Directional supervision:
Characteristic angle: 30 to 90° in steps of 1 10
Limit angle: 30 to 90° in steps of 1

5
Right blinder (Quad only):
Reach: 0.02 to 500  in steps of 0.01 0
0% 10% 20% 30% 40% 50% 60% 70% 80%
Characteristic angle: 60 to 90° in steps of 1 Fault Location [%]
Left Blinder (Quad only): 837717A1.CDR
Reach: 0.02 to 500  in steps of 0.01

Time delay: 0.000 to 65.535 s in steps of 0.001
Timer accuracy: ±3% of operate time or ±1/4 cycle
(whichever is greater)
Current supervision:
Level: line-to-line current
Pickup: 0.050 to 30.000 pu in steps of 0.001
Dropout: 97 to 98%
Memory duration: 5 to 25 cycles in steps of 1
VT location: all delta-wye and wye-delta transformers
CT location: all delta-wye and wye-delta transformers
Voltage supervision pickup (series compensation applications):
0 to 5.000 pu in steps of 0.001

2 PRODUCT DESCRIPTION 2.2 SPECIFICATIONS
GROUND DISTANCE GROUND DISTANCE OPERATING TIME CURVES

Characteristic: Mho (memory polarized or offset) or The operating times are response times of a microprocessor part
Quad (memory polarized or non-direc- of the relay. See output contacts specifications for estimation of
tional), selectable individually per zone the total response time for a particular application. The operating
Reactance polarization: negative-sequence or zero-sequence times are average times including variables such as fault inception
current angle or type of a voltage source (magnetic VTs and CVTs).
Non-homogeneity angle: –40 to 40° in steps of 1
Number of zones: 5
2
Ground Element (21G)
Directionality: forward, reverse, or non-directional per 35

SIR = 0.1
zone SIR = 1
30 SIR = 10
Reach (secondary ): 0.02 to 500.00  in steps of 0.01 SIR = 20
SIR = 30
Reach accuracy: ±5% including the effect of CVT tran- 25
Operating Time [ms]

sients up to an SIR of 30 20
Distance characteristic angle: 30 to 90° in steps of 1

15
Distance comparator limit angle: 30 to 90° in steps of 1
Directional supervision: 10
Characteristic angle: 30 to 90° in steps of 1 5
Limit angle: 30 to 90° in steps of 1 0
Zero-sequence compensation 0% 10% 20% 30% 40% 50% 60% 70% 80%
Fault Location [%]
Z0/Z1 magnitude: 0.00 to 10.00 in steps of 0.01
837718A1.CDR
Z0/Z1 angle: –90 to 90° in steps of 1

Zero-sequence mutual compensation LINE PICKUP
Z0M/Z1 magnitude: 0.00 to 7.00 in steps of 0.01 Phase instantaneous overcurrent: 0.000 to 30.000 pu
Z0M/Z1 angle: –90 to 90° in steps of 1 Undervoltage pickup: 0.000 to 3.000 pu
Right blinder (Quad only): Overvoltage delay: 0.000 to 65.535 s
Reach: 0.02 to 500  in steps of 0.01
Left blinder (Quad only): PHASE/NEUTRAL/GROUND TOC
Reach: 0.02 to 500  in steps of 0.01 Current: Phasor or RMS
Characteristic angle: 60 to 90° in steps of 1 Pickup level: 0.000 to 30.000 pu in steps of 0.001
Time delay: 0.000 to 65.535 s in steps of 0.001 Dropout level: 97% to 98% of pickup
Timer accuracy: ±3% of operate time or ±1/4 cycle Level accuracy:
(whichever is greater) for 0.1 to 2.0  CT: ±0.5% of reading or ±0.4% of rated
Current supervision: (whichever is greater)
Level: neutral current (3I_0) for > 2.0  CT: ±1.5% of reading > 2.0  CT rating
Pickup: 0.050 to 30.000 pu in steps of 0.001 Curve shapes: IEEE Moderately/Very/Extremely
Dropout: 97 to 98% Inverse; IEC (and BS) A/B/C and Short
Inverse; GE IAC Inverse, Short/Very/
Memory duration: 5 to 25 cycles in steps of 1
Extremely Inverse; I2t; FlexCurves™
Voltage supervision pickup (series compensation applications): (programmable); Definite Time (0.01 s
0 to 5.000 pu in steps of 0.001 base curve)
Curve multiplier: Time Dial = 0.00 to 600.00 in steps of
0.01
Reset type: Instantaneous/Timed (per IEEE)
Curve timing accuracy
at 1.03 to 20 x pickup: ±3.5% of operate time or ±½ cycle
(whichever is greater) from pickup to
operate

PHASE/NEUTRAL/GROUND IOC PHASE DIRECTIONAL OVERCURRENT

Pickup level: 0.000 to 30.000 pu in steps of 0.001 Relay connection: 90° (quadrature)
Dropout level: 97 to 98% of pickup Quadrature voltage: ABC phase seq.: phase A (VBC), phase
Level accuracy: B (VCA), phase C (VAB); ACB phase
seq.: phase A (VCB), phase B (VAC),
0.1 to 2.0  CT rating: ±0.5% of reading or ±0.4% of rated
phase C (VBA)
Polarizing voltage threshold: 0.000 to 3.000 pu in steps of 0.001
> 2.0  CT rating ±1.5% of reading
2 Overreach:
Pickup delay:
<2%
0.00 to 600.00 s in steps of 0.01
Current sensitivity threshold: 0.05 pu
Angle accuracy: ±2°
Reset delay: 0.00 to 600.00 s in steps of 0.01
Operation time (FlexLogic operands):
Operate time: <16 ms at 3  pickup at 60 Hz
(Phase/Ground IOC) Tripping (reverse load, forward fault):
12 ms, typically
<20 ms at 3  pickup at 60 Hz
Blocking (forward load, reverse fault):
(Neutral IOC)
8 ms, typically
Timer accuracy: ±3% of operate time or ±1/4 cycle
(whichever is greater) NEUTRAL DIRECTIONAL OVERCURRENT
Directionality: Co-existing forward and reverse
NEGATIVE SEQUENCE TOC
Polarizing: Voltage, Current, Dual, Dual-V, Dual-I
Pickup level: 0.000 to 30.000 pu in steps of 0.001
Polarizing voltage: V_0 or VX
Dropout level: 97% to 98% of pickup
Polarizing current: IG
Level accuracy: ±0.5% of reading or ±0.4% of rated
(whichever is greater) Operating current: I_0
from 0.1 to 2.0 x CT rating Level sensing: 3  (|I_0| – K  |I_1|), IG
±1.5% of reading > 2.0 x CT rating Restraint, K: 0.000 to 0.500 in steps of 0.001
Curve shapes: IEEE Moderately/Very/Extremely Characteristic angle: –90 to 90° in steps of 1
Inverse; IEC (and BS) A/B/C and Short Limit angle: 40 to 90° in steps of 1, independent for
Inverse; GE IAC Inverse, Short/Very/
forward and reverse
Extremely Inverse; I2t; FlexCurves™
Angle accuracy: ±2°
(programmable); Definite Time (0.01 s
base curve) Offset impedance: 0.00 to 250.00  in steps of 0.01
Curve multiplier (Time dial): 0.00 to 600.00 in steps of 0.01 Pickup level: 0.002 to 30.000 pu in steps of 0.01
Reset type: Instantaneous/Timed (per IEEE) and Lin- Dropout level: 97 to 98%
ear Operation time: <16 ms at 3  pickup at 60 Hz
Curve timing accuracy NEGATIVE SEQUENCE DIRECTIONAL OC
at 1.03 to 20 x pickup: ±3.5% of operate time or ±½ cycle Directionality: Co-existing forward and reverse
(whichever is greater) from pickup to Polarizing: Voltage
operate
Polarizing voltage: V_2
NEGATIVE SEQUENCE IOC Operating current: I_2
Pickup level: 0.000 to 30.000 pu in steps of 0.001 Level sensing:
Dropout level: 97 to 98% of pickup Zero-sequence:|I_0| – K  |I_1|
Level accuracy: 0.1 to 2.0  CT rating: ±0.5% of reading Negative-sequence:|I_2| – K  |I_1|
or ±0.4% of rated (whichever is greater); Restraint, K: 0.000 to 0.500 in steps of 0.001
2.0  CT rating: ±1.5% of reading
Overreach: 2%
Limit angle: 40 to 90° in steps of 1, independent for
Pickup delay: 0.00 to 600.00 s in steps of 0.01 forward and reverse
Reset delay: 0.00 to 600.00 s in steps of 0.01 Angle accuracy: ±2°
Operate time: <20 ms at 3  pickup at 60 Hz Offset impedance: 0.00 to 250.00  in steps of 0.01
Timer accuracy: ±3% of operate time or ±1/4 cycle Pickup level: 0.015 to 30.000 pu in steps of 0.01
(whichever is greater) Dropout level: 97 to 98%
Operation time: <16 ms at 3  pickup at 60 Hz

WATTMETRIC ZERO-SEQUENCE DIRECTIONAL NEUTRAL OVERVOLTAGE

Measured power: zero-sequence Pickup level: 0.000 to 3.000 pu in steps of 0.001
Number of elements: 2 Dropout level: 97 to 98% of pickup
Characteristic angle: 0 to 360° in steps of 1 Level accuracy: ±0.5% of reading from 10 to 208 V
Minimum power: 0.001 to 1.200 pu in steps of 0.001 Pickup delay: 0.00 to 600.00 s in steps of 0.01 (definite
Pickup level accuracy: ±1% or ±0.0025 pu, whichever is greater time) or user-defined curve
Hysteresis: 3% or 0.001 pu, whichever is greater Reset delay: 0.00 to 600.00 s in steps of 0.01
Pickup delay: definite time (0 to 600.00 s in steps of
0.01), inverse time, or FlexCurve
at >1.1 x pickup: ±3.5% of operate time or ±1 cycle
2
Inverse time multiplier: 0.01 to 2.00 s in steps of 0.01 (whichever is greater) from pickup to
operate
Curve timing accuracy: ±3.5% of operate time or ±1 cycle
(whichever is greater) from pickup to Operate time: 30 ms at 1.10  pickup at 60 Hz
operate AUXILIARY OVERVOLTAGE
Operate time: <30 ms at 60 Hz Pickup level: 0.000 to 3.000 pu in steps of 0.001
PHASE UNDERVOLTAGE Dropout level: 97 to 98% of pickup
Pickup level: 0.000 to 3.000 pu in steps of 0.001 Level accuracy: ±0.5% of reading from 10 to 208 V
Dropout level: 102 to 103% of pickup Pickup delay: 0 to 600.00 s in steps of 0.01
Level accuracy: ±0.5% of reading from 10 to 208 V Reset delay: 0 to 600.00 s in steps of 0.01
Curve shapes: GE IAV Inverse; Timer accuracy: ±3% of operate time or ±1/4 cycle
Definite Time (0.1s base curve) (whichever is greater)
Curve multiplier: Time dial = 0.00 to 600.00 in steps of Operate time: 30 ms at 1.10  pickup at 60 Hz
0.01
NEGATIVE SEQUENCE OVERVOLTAGE
at <0.90 x pickup: ±3.5% of operate time or ±1/2 cycle
Dropout level: 97 to 98% of pickup
(whichever is greater) from pickup to
operate Level accuracy: ±0.5% of reading from 10 to 208 V
Pickup delay: 0 to 600.00 s in steps of 0.01
AUXILIARY UNDERVOLTAGE Reset delay: 0 to 600.00 s in steps of 0.01
Timer accuracy: ±3% of operate time or ±20 ms, which-
Dropout level: 102 to 103% of pickup ever is greater
Level accuracy: ±0.5% of reading from 10 to 208 V Operate time: <30 ms at 1.10  pickup at 60 Hz
Curve shapes: GE IAV Inverse, Definite Time
Curve multiplier: Time Dial = 0 to 600.00 in steps of 0.01
UNDERFREQUENCY
Minimum signal: 0.10 to 1.25 pu in steps of 0.01
Pickup level: 20.00 to 65.00 Hz in steps of 0.01
at <0.90 x pickup: ±3.5% of operate time or ±1/2 cycle
(whichever is greater) from pickup to Dropout level: pickup + 0.03 Hz
operate Level accuracy: ±0.001 Hz
Time delay: 0 to 65.535 s in steps of 0.001
PHASE OVERVOLTAGE
Voltage: Phasor only Timer accuracy: ±3% of operate time or ±1/4 cycle
Operate time: typically 4 cycles at 0.1 Hz/s change
Dropout level: 97 to 98% of pickup
typically 3.5 cycles at 0.3 Hz/s change
Level accuracy: ±0.5% of reading from 10 to 208 V typically 3 cycles at 0.5 Hz/s change
Pickup delay: 0.00 to 600.00 in steps of 0.01 s Typical times are average operate times including variables such
Operate time: 30 ms at 1.10  pickup at 60 Hz as frequency change instance, test method, etc., and may vary by
Timer accuracy: ±3% of operate time or ±1/4 cycle ±0.5 cycles.
(whichever is greater) OVERFREQUENCY
COMPENSATED OVERVOLTAGE Pickup level: 20.00 to 65.00 Hz in steps of 0.01
Elements: 1 Dropout level: pickup – 0.03 Hz
Stages: 3 Level accuracy: ±0.001 Hz
Pickup threshold: 0.250 to 3.000 pu in steps of 0.001 Time delay: 0 to 65.535 s in steps of 0.001
Pickup level accuracy: ±0.5% of reading from 10 to 208 V Timer accuracy: ±3% of operate time or ±1/4 cycle
Hysteresis: 97 to 98% of pickup (whichever is greater)
Pickup delay: 0.00 to 600.00 s in steps of 0.01 Operate time: typically 4 cycles at 0.1 Hz/s change
Timer accuracy: ±3% of operate time or ±20 ms (which- typically 3.5 cycles at 0.3 Hz/s change
typically 3 cycles at 0.5 Hz/s change
ever is greater)
Operate time: <2 cycles at 1.10 × pickup

Typical times are average operate times including variables such BREAKER RESTRIKE
as frequency change instance, test method, etc., and may vary by Principle: detection of high-frequency overcurrent
±0.5 cycles. condition ¼ cycle after breaker opens
RATE OF CHANGE OF FREQUENCY Availability: one per CT/VT module (not including 8Z
df/dt trend: increasing, decreasing, bi-directional modules)
df/dt pickup level: 0.10 to 15.00 Hz/s in steps of 0.01 Pickup level: 0.1 to 2.00 pu in steps of 0.01
df/dt dropout level: 96% of pickup Reset delay: 0.000 to 65.535 s in steps of 0.001
2 df/dt level accuracy:

Overvoltage supv.:
80 mHz/s or 3.5%, whichever is greater
0.100 to 3.000 pu in steps of 0.001
SYNCHROCHECK
Max voltage difference: 0 to 400000 V in steps of 1
Overcurrent supv.: 0.000 to 30.000 pu in steps of 0.001 Max angle difference: 0 to 100° in steps of 1
Pickup delay: 0 to 65.535 s in steps of 0.001 Max freq. difference: 0.00 to 2.00 Hz in steps of 0.01
Reset delay: 0 to 65.535 s in steps of 0.001 Hysteresis for max. freq. diff.: 0.00 to 0.10 Hz in steps of 0.01
Timer accuracy: ±3% of operate time or ±1/4 cycle Dead source function: None, LV1 & DV2, DV1 & LV2, DV1 or
(whichever is greater) DV2, DV1 xor DV2, DV1 & DV2
95% settling time for df/dt: <24 cycles (L = Live, D = Dead)
Operate time: typically 6.5 cycles at 2  pickup AUTORECLOSURE
typically 5.5 cycles at 3  pickup Two breakers applications
typically 4.5 cycles at 5  pickup Single- and three-pole tripping schemes
Typical times are average operate times including variables such Up to 4 reclose attempts before lockout
as frequency change instance, test method, etc., and may vary by
Selectable reclosing mode and breaker sequence
±0.5 cycles.
PILOT-AIDED SCHEMES
BREAKER FAILURE
Direct Underreaching Transfer Trip (DUTT)
Mode: 1-pole, 3-pole
Permissive Underreaching Transfer Trip (PUTT)
Current supervision: phase, neutral current
Permissive Overreaching Transfer Trip (POTT)
Current supv. pickup: 0.001 to 30.000 pu in steps of 0.001
Hybrid POTT Scheme
Current supv. dropout: 97 to 98% of pickup
Directional Comparison Blocking Scheme
Current supv. accuracy:
Directional Comparison Unblocking Scheme (DCUB)
0.1 to 2.0  CT rating: ±0.75% of reading or ±2% of rated
(whichever is greater) TRIP OUTPUT
above 2  CT rating: ±2.5% of reading Collects trip and reclose input requests and issues outputs to con-
trol tripping and reclosing.
BREAKER ARCING CURRENT
Communications timer delay: 0 to 65535 s in steps of 0.001
Principle: accumulates breaker duty (I2t) and mea-
sures fault duration Evolving fault timer: 0.000 to 65.535 s in steps of 0.001
Initiation: programmable per phase from any Flex- Timer accuracy: ±3% of operate time or ±1/4 cycle
Logic operand (whichever is greater)
Compensation for auxiliary relays: 0 to 65.535 s in steps of 0.001 POWER SWING DETECT
Alarm threshold: 0 to 50000 kA2-cycle in steps of 1 Functions: Power swing block, Out-of-step trip
Fault duration accuracy: 0.25 of a power cycle Characteristic: Mho or Quad
Availability: 1 per CT bank with a minimum of 2 Measured impedance: Positive-sequence
Blocking / tripping modes: 2-step or 3-step
BREAKER FLASHOVER
Operating quantity: phase current, voltage and voltage differ- Tripping mode: Early or Delayed
ence Current supervision:
Pickup level voltage: 0 to 1.500 pu in steps of 0.001 Pickup level: 0.050 to 30.000 pu in steps of 0.001
Dropout level voltage: 97 to 98% of pickup Dropout level: 97 to 98% of pickup
Pickup level current: 0 to 1.500 pu in steps of 0.001 Fwd / reverse reach (sec. ): 0.10 to 500.00  in steps of 0.01
Dropout level current: 97 to 98% of pickup Left and right blinders (sec. ): 0.10 to 500.00  in steps of 0.01
Level accuracy: ±0.5% or ±0.1% of rated, whichever is Impedance accuracy: ±5%
greater Fwd / reverse angle impedances: 40 to 90° in steps of 1
Pickup delay: 0 to 65.535 s in steps of 0.001 Angle accuracy: ±2°
Timer accuracy: ±3% of operate time or ±42 ms, which- Characteristic limit angles: 40 to 140° in steps of 1
ever is greater Timers: 0.000 to 65.535 s in steps of 0.001
Operate time: <42 ms at 1.10  pickup at 60 Hz Timer accuracy: ±3% of operate time or ±1/4 cycle

LOAD ENCROACHMENT THERMAL OVERLOAD PROTECTION

Responds to: Positive-sequence quantities Thermal overload curves: IEC 255-8 curve
Minimum voltage: 0.000 to 3.000 pu in steps of 0.001 Base current: 0.20 to 3.00 pu in steps of 0.01
Reach (sec. ): 0.02 to 250.00  in steps of 0.01 Overload (k) factor: 1.00 to 1.20 pu in steps of 0.05
Impedance accuracy: ±5% Trip time constant: 0 to 1000 min. in steps of 1
Angle: 5 to 50° in steps of 1 Reset time constant: 0 to 1000 min. in steps of 1
Angle accuracy: ±2° Minimum reset time: 0 to 1000 min. in steps of 1
Pickup delay:
Reset delay:
0 to 65.535 s in steps of 0.001
0 to 65.535 s in steps of 0.001
Timer accuracy (cold curve): ±100 ms or 2%, whichever is greater
Timer accuracy (hot curve): ±500 ms or 2%, whichever is greater
2
Timer accuracy: ±3% of operate time or ±1/4 cycle for Ip < 0.9 × k × Ib and I / (k × Ib) > 1.1
(whichever is greater) TRIP BUS (TRIP WITHOUT FLEXLOGIC)
Operate time: <30 ms at 60 Hz Number of elements: 6
OPEN POLE DETECTOR Number of inputs: 16
Functionality: Detects an open pole condition, monitor- Operate time: <2 ms at 60 Hz
ing breaker auxiliary contacts, the cur- Timer accuracy: ±3% or 10 ms, whichever is greater
rent in each phase and optional voltages
on the line
Current pickup level: 0.000 to 30.000 pu in steps of 0.001
Line capacitive reactances (XC1, XC0): 300.0 to 9999.9 sec.  in
steps of 0.1
Remote current pickup level: 0.000 to 30.000 pu in steps of 0.001
Current dropout level: pickup + 3%, not less than 0.05 pu
2.2.2 USER PROGRAMMABLE ELEMENTS
FLEXLOGIC FLEXELEMENTS™
Programming language: Reverse Polish Notation with graphical Number of elements: 8
visualization (keypad programmable) Operating signal: any analog actual value, or two values in
Lines of code: 512 differential mode
Internal variables: 64 Operating signal mode: signed or absolute value
Supported operations: NOT, XOR, OR (2 to 16 inputs), AND (2 Operating mode: level, delta
to 16 inputs), NOR (2 to 16 inputs), Comparator direction: over, under
NAND (2 to 16 inputs), latch (reset-domi- Pickup Level: –90.000 to 90.000 pu in steps of 0.001
nant), edge detectors, timers
Hysteresis: 0.1 to 50.0% in steps of 0.1
Inputs: any logical variable, contact, or virtual
Delta dt: 20 ms to 60 days
input
Pickup & dropout delay: 0.000 to 65.535 s in steps of 0.001
Number of timers: 32
Pickup delay: 0 to 60000 (ms, sec., min.) in steps of 1 NON-VOLATILE LATCHES
Dropout delay: 0 to 60000 (ms, sec., min.) in steps of 1 Type: set-dominant or reset-dominant
Number: 16 (individually programmed)
FLEXCURVES™
Number: 4 (A through D) Output: stored in non-volatile memory
Reset points: 40 (0 through 1 of pickup) Execution sequence: as input prior to protection, control, and
FlexLogic
Operate points: 80 (1 through 20 of pickup)
Time delay: 0 to 65535 ms in steps of 1 USER-PROGRAMMABLE LEDs
Number: 48 plus trip and alarm
FLEX STATES Programmability: from any logical variable, contact, or vir-
Number: up to 256 logical variables grouped tual input
under 16 Modbus addresses
Reset mode: self-reset or latched
Programmability: any logical variable, contact, or virtual
input LED TEST
Initiation: from any digital input or user-program-
mable condition
Number of tests: 3, interruptible at any time
Duration of full test: approximately 3 minutes
Test sequence 1: all LEDs on
Test sequence 2: all LEDs off, one LED at a time on for 1 s
Test sequence 3: all LEDs on, one LED at a time off for 1 s

USER-DEFINABLE DISPLAYS SELECTOR SWITCH

Number of displays: 16 Number of elements: 2
Lines of display: 2  20 alphanumeric characters Upper position limit: 1 to 7 in steps of 1
Parameters: up to 5, any Modbus register addresses Selecting mode: time-out or acknowledge
Invoking and scrolling: keypad, or any user-programmable con- Time-out timer: 3.0 to 60.0 s in steps of 0.1
dition, including pushbuttons Control inputs: step-up and 3-bit
CONTROL PUSHBUTTONS Power-up mode: restore from non-volatile memory or syn-
Number of pushbuttons: 7
Operation: drive FlexLogic operands
chronize to a 3-bit control input or synch/
restore mode
2
USER-PROGRAMMABLE PUSHBUTTONS (OPTIONAL) DIGITAL ELEMENTS
Number of pushbuttons: 12 (standard faceplate); Number of elements: 48
16 (enhanced faceplate) Operating signal: any FlexLogic operand
Mode: self-reset, latched Pickup delay: 0.000 to 999999.999 s in steps of 0.001
Display message: 2 lines of 20 characters each Dropout delay: 0.000 to 999999.999 s in steps of 0.001
Drop-out timer: 0.00 to 60.00 s in steps of 0.05 Timing accuracy: ±3% or ±4 ms, whichever is greater
Autoreset timer: 0.2 to 600.0 s in steps of 0.1
Hold timer: 0.0 to 10.0 s in steps of 0.1
2.2.3 MONITORING
OSCILLOGRAPHY DATA LOGGER

Maximum records: 64 Number of channels: 1 to 16
Sampling rate: 64 samples per power cycle Parameters: any available analog actual value
Triggers: any element pickup, dropout, or operate; Sampling rate: 15 to 3600000 ms in steps of 1
digital input change of state; digital out- Trigger: any FlexLogic operand
put change of state; FlexLogic equation
Mode: continuous or triggered
Data: AC input channels; element state; digital
Storage capacity: (NN is dependent on memory)
input state; digital output state
1-second rate:
Data storage: in non-volatile memory
01 channel for NN days
EVENT RECORDER 16 channels for NN days
Capacity: 1024 events 
Time-tag: to 1 microsecond 60-minute rate:
Triggers: any element pickup, dropout, or operate; 01 channel for NN days
digital input change of state; digital out- 16 channels for NN days
put change of state; self-test events FAULT LOCATOR
Data storage: in non-volatile memory Method: single-ended
Voltage source: wye-connected VTs, delta-connected
VTs and neutral voltage, delta-connected
VTs and zero-sequence current (approxi-
mation)
Maximum accuracy if: fault resistance is zero or fault currents
from all line terminals are in phase
Relay accuracy: ±1.5% (V > 10 V, I > 0.1 pu)
Worst-case accuracy:
VT%error + user data
CT%error + user data
ZLine%error + user data
METHOD%error + see chapter 8
RELAY ACCURACY%error + (1.5%)

PHASOR MEASUREMENT UNIT

Output format: per IEEE C37.118 or IEC 61850-90-5
standard
Number of channels: 14 synchrophasors, 8 analogs, 16 digi-
tals
TVE (total vector error) <1%
Triggering: frequency, voltage, current, power, rate
of change of frequency, user-defined
Reporting rate: 1, 2, 5, 10, 12, 15, 20, 25, 30, 50, or 60 2
times per second for P and M class, and
100 or 120 times per second for P class
only
Number of clients: One over TCP/IP port and one over
UDP/IP per aggregator
AC ranges: As indicated in appropriate specifications
sections
Network reporting format: 16-bit integer (for C37.118) or 32-bit
IEEE floating point numbers
Network reporting style: rectangular (real and imaginary for
C37.188) or polar (magnitude and angle)
coordinates
Post-filtering: none, 3-point, 5-point, 7-point
Calibration: ±5° (angle) and ±5% (magnitude)
2.2.4 METERING
RMS CURRENT: PHASE, NEUTRAL, AND GROUND WATT-HOURS (POSITIVE AND NEGATIVE)
Accuracy at Accuracy: ±2.0% of reading
0.1 to 2.0  CT rating: ±0.25% of reading or ±0.1% of rated Range: ±0 to 1  106 MWh
(whichever is greater) Parameters: three-phase only
2.0  CT rating: ±1.0% of reading
Update rate: 50 ms
RMS VOLTAGE
Accuracy: ±0.5% of reading from 10 to 208 V
VAR-HOURS (POSITIVE AND NEGATIVE)
Accuracy: ±2.0% of reading
REAL POWER (WATTS) Range: ±0 to 1  106 Mvarh
Accuracy at 0.1 to 1.5 x
Parameters: three-phase only
CT rating and 0.8 to
Update rate: 50 ms
1.2 x VT rating: ±1.0% of reading at –1.0  PF< –0.8 and
0.8 < PF 10 FREQUENCY
Accuracy at
REACTIVE POWER (VARS) V = 0.8 to 1.2 pu: ±0.01 Hz (when voltage signal is used
Accuracy at 0.1 to 1.5 x for frequency measurement)
CT rating and 0.8 to I = 0.1 to 0.25 pu: ±0.05 Hz
1.2 x VT rating: ±1.0% of reading at –0.2  PF  0.2 I > 0.25 pu: ±0.02 Hz (when current signal is used for
frequency measurement)
APPARENT POWER (VA)
Accuracy at 0.1 to 1.5 x
CT rating and 0.8 to
1.2 x VT rating: ±1.0% of reading
2.2.5 INPUTS
AC CURRENT Current withstand: 20 ms at 250 times rated

CT rated primary: 1 to 50000 A 1 sec. at 100 times rated
CT rated secondary: 1 A or 5 A by connection continuous 4xInom; URs equipped with
24 CT inputs have a maximum operating
Relay burden: < 0.2 VA at rated secondary
temp. of 50°C
Conversion range:
Short circuit rating: 150000 RMS symmetrical amperes, 250
Standard CT: 0.02 to 46  CT rating RMS symmetrical
V maximum (primary current to external
Sensitive Ground CT module:
CT)
0.002 to 4.6  CT rating RMS symmetrical

AC VOLTAGE RTD INPUTS

VT rated secondary: 50.0 to 240.0 V Types (3-wire): 100 Platinum, 100 & 120 Nickel, 10
VT ratio: 1.00 to 24000.00Relay burden:< 0.25 VA Copper
at 120 V Sensing current: 5 mA
Conversion range: 1 to 275 V Range: –50 to +250°C
Voltage withstand: continuous at 260 V to neutral Accuracy: ±2°C
1 min./hr at 420 V to neutral Isolation: 36 V pk-pk
2 FREQUENCY
Nominal frequency setting:25 to 60 Hz
IRIG-B INPUT
Amplitude modulation: 1 to 10 V pk-pk
Sampling frequency: 64 samples per power cycle DC shift: TTL–Compatible
Tracking frequency range:20 to 65 Hz Input impedance: 50 k
CONTACT INPUTS Isolation: 2 kV
Dry contacts: 1000  maximum REMOTE INPUTS (IEC 61850 GSSE/GOOSE)
Wet contacts: 300 V DC maximum Input points: 32, configured from 64 incoming bit pairs
Selectable thresholds: 17 V, 33 V, 84 V, 166 V Remote devices: 16
Tolerance: ±10% Default states on loss of comms.: On, Off, Latest/Off, Latest/On
Contacts per common return: 4 Remote DPS inputs: 5
Recognition time: < 1 ms
DIRECT INPUTS
Debounce time: 0.0 to 16.0 ms in steps of 0.5
Input points: 32
Continuous current draw:3 mA (when energized)
Remote devices: 16
CONTACT INPUTS WITH AUTO-BURNISHING Default states on loss of comms.: On, Off, Latest/Off, Latest/On
Dry contacts: 1000  maximum Ring configuration: Yes, No
Wet contacts: 300 V DC maximum Data rate: 64 or 128 kbps
Selectable thresholds: 17 V, 33 V, 84 V, 166 V CRC: 32-bit
Tolerance: ±10% CRC alarm:
Contacts per common return: 2 Responding to: Rate of messages failing the CRC
Recognition time: < 1 ms Monitoring message count: 10 to 10000 in steps of 1
Alarm threshold: 1 to 1000 in steps of 1
Debounce time: 0.0 to 16.0 ms in steps of 0.5
Unreturned message alarm:
Continuous current draw:3 mA (when energized)
Responding to: Rate of unreturned messages in the ring
Auto-burnish impulse current: 50 to 70 mA configuration
Duration of auto-burnish impulse: 25 to 50 ms Monitoring message count: 10 to 10000 in steps of 1
DCMA INPUTS Alarm threshold: 1 to 1000 in steps of 1
Current input (mA DC): 0 to –1, 0 to +1, –1 to +1, 0 to 5, 0 to 10, TELEPROTECTION
0 to 20, 4 to 20 (programmable) Input points: 16
Input impedance: 379 ±10% Remote devices: 3
Conversion range: –1 to + 20 mA DC Default states on loss of comms.: On, Off, Latest/Off, Latest/On
Accuracy: ±0.2% of full scale Ring configuration: No
Type: Passive Data rate: 64 or 128 kbps
CRC: 32-bit
2.2.6 POWER SUPPLY
LOW RANGE HIGH RANGE

Nominal DC voltage: 24 to 48 V Nominal DC voltage: 125 to 250 V
Minimum DC voltage: 20 V Minimum DC voltage: 88 V
Maximum DC voltage: 60 V Maximum DC voltage: 300 V
Voltage loss hold-up: 20 ms duration at nominal Nominal AC voltage: 100 to 240 V at 50/60 Hz
NOTE: Low range is DC only. Minimum AC voltage: 88 V at 25 to 100 Hz
Maximum AC voltage: 265 V at 25 to 100 Hz
Voltage loss hold-up: 200 ms duration at nominal

ALL RANGES INTERNAL FUSE

Volt withstand: 2  Highest Nominal Voltage for 10 ms RATINGS
Power consumption: typical = 15 to 20 W/VA Low range power supply: 8 A / 250 V
maximum = 50 W/VA High range power supply: 4 A / 250 V
contact factory for exact order code con- INTERRUPTING CAPACITY
sumption AC: 100 000 A RMS symmetrical
DC: 10 000 A
2.2.7 OUTPUTS 2
FORM-A RELAY FAST FORM-C RELAY
Make and carry for 0.2 s: 30 A as per ANSI C37.90 Make and carry: 0.1 A max. (resistive load)
Carry continuous: 6A Minimum load impedance:
Break (DC inductive, L/R = 40 ms): INPUT IMPEDANCE

VOLTAGE
VOLTAGE CURRENT 2 W RESISTOR 1 W RESISTOR
24 V 1A 250 V DC 20 K 50 K
48 V 0.5 A 120 V DC 5 K 2 K
125 V 0.3 A 48 V DC 2 K 2 K
250 V 0.2 A 24 V DC 2 K 2 K
Operate time: < 4 ms Note: values for 24 V and 48 V are the same due to a
required 95% voltage drop across the load impedance.
Contact material: silver alloy
Operate time: < 0.6 ms
LATCHING RELAY Internal Limiting Resistor: 100 , 2 W
Make and carry for 0.2 s: 30 A as per ANSI C37.90
Carry continuous: 6 A as per IEEE C37.90 SOLID-STATE OUTPUT RELAY
Operate and release time: <100 s
Break (DC resistive as per IEC61810-1):
Maximum voltage: 265 V DC
VOLTAGE CURRENT
Maximum continuous current: 5 A at 45°C; 4 A at 65°C
24 V 6A
Make and carry:
48 V 1.6 A
for 0.2 s: 30 A as per ANSI C37.90
125 V 0.4 A for 0.03 s 300 A
250 V 0.2 A Breaking capacity:
Operate time: < 4 ms UL508 Utility Industrial
application application
Contact material: silver alloy (autoreclose
Control: separate operate and reset inputs scheme)
Control mode: operate-dominant or reset-dominant Operations/ 5000 ops / 5 ops /
interval 1 s-On, 9 s-Off 0.2 s-On, 10000 ops /
FORM-A VOLTAGE MONITOR 0.2 s-Off 0.2 s-On,
Applicable voltage: approx. 15 to 250 V DC 1000 ops / within 1 30 s-Off
0.5 s-On, 0.5 s-Off minute
Trickle current: approx. 1 to 2.5 mA
Break 3.2 A
FORM-A CURRENT MONITOR capability L/R = 10 ms
(0 to 250 V
Threshold current: approx. 80 to 100 mA DC) 1.6 A 10 A 10 A
L/R = 20 ms L/R = 40 ms L/R = 40 ms
FORM-C AND CRITICAL FAILURE RELAY 0.8 A
Make and carry for 0.2 s: 30 A as per ANSI C37.90 L/R = 40 ms
Carry continuous: 8A
CONTROL POWER EXTERNAL OUTPUT
Break (DC inductive, L/R = 40 ms):
(FOR DRY CONTACT INPUT)
VOLTAGE CURRENT Capacity: 100 mA DC at 48 V DC
24 V 1A Isolation: ±300 Vpk
48 V 0.5 A
REMOTE OUTPUTS (IEC 61850 GSSE/GOOSE)
125 V 0.3 A
Standard output points: 32
250 V 0.2 A
User output points: 32
Operate time: < 8 ms
DIRECT OUTPUTS
Contact material: silver alloy
Output points: 32

DCMA OUTPUTS
Range: –1 to 1 mA, 0 to 1 mA, 4 to 20 mA
Max. load resistance: 12 k for –1 to 1 mA range
12 k for 0 to 1 mA range
600  for 4 to 20 mA range
Accuracy: ±0.75% of full-scale for 0 to 1 mA range
±0.5% of full-scale for –1 to 1 mA range
±0.75% of full-scale for 0 to 20 mA range
2 99% Settling time to a step change: 100 ms
Isolation: 1.5 kV
Driving signal: any FlexAnalog quantity
Upper and lower limit for the driving signal: –90 to 90 pu in steps of
0.001
RS232
Front port: 19.2 kbps, Modbus RTU
PRECISION TIME PROTOCOL (PTP)
RS485 PTP IEEE Std 1588 2008 (version 2)
1 rear port: Up to 115 kbps, Modbus RTU, isolated Power Profile (PP) per IEEE Standard PC37.238TM2011
together at 36 Vpk
Slave-only ordinary clock
Typical distance: 1200 m
Peer delay measurement mechanism
Isolation: 2 kV
PARALLEL REDUNDANCY PROTOCOL (PRP)
ETHERNET (FIBER) (IEC 62439-3 CLAUSE 4, 2012)
PARAMETER FIBER TYPE Ethernet ports used: 2 and 3
100MB MULTI- Networks supported: 10/100 MB Ethernet
MODE
Wavelength 1310 nm
Connector LC
Transmit power –20 dBm
Receiver sensitivity –30 dBm
Power budget 10 dB
Maximum input –14 dBm
power
Typical distance 2 km
Duplex full/half
Redundancy yes
ETHERNET (10/100 MB TWISTED PAIR)

Modes: 10 MB, 10/100 MB (auto-detect)
Connector: RJ45
SIMPLE NETWORK TIME PROTOCOL (SNTP)
clock synchronization error: <10 ms (typical)

2.2.9 INTER-RELAY COMMUNICATIONS
SHIELDED TWISTED-PAIR INTERFACE OPTIONS TYPICAL LINK DISTANCE

INTERFACE TYPE TYPICAL DISTANCE EMITTER TYPE CABLE CONNECTOR TYPICAL
TYPE TYPE DISTANCE
RS422 1200 m
820 nm LED, 62.5/125 μm ST 1.65 km
G.703 100 m multimode
RS422 distance is based on transmitter power and 1300 nm LED,
multimode
62.5/125 μm ST 3.8 km 2
NOTE does not take into consideration the clock source
provided by the user. 1300 nm ELED, 9/125 μm ST 11.4 km
single mode
LINK POWER BUDGET 1300 nm Laser, 9/125 μm ST 64 km
single mode
EMITTER, TRANSMIT RECEIVED POWER
FIBER TYPE POWER SENSITIVITY BUDGET 1550 nm Laser, 9/125 μm ST 105 km
single-mode
820 nm LED, –20 dBm –30 dBm 10 dB
Multimode
1300 nm LED, –21 dBm –30 dBm 9 dB Typical distances listed are based on the follow-
Multimode ing assumptions for system loss. As actual losses
1300 nm ELED, –23 dBm –32 dBm 9 dB NOTE vary from one installation to another, the distance
Singlemode covered by your system may vary.
1300 nm Laser, –1 dBm –30 dBm 29 dB
Singlemode CONNECTOR LOSSES (TOTAL OF BOTH ENDS)
ST connector 2 dB
1550 nm Laser, +5 dBm –30 dBm 35 dB
Singlemode FIBER LOSSES
820 nm multimode 3 dB/km
These power budgets are calculated from the manu-
1300 nm multimode 1 dB/km
NOTE facturer’s worst-case transmitter power and worst
case receiver sensitivity. 1300 nm singlemode 0.35 dB/km
1550 nm singlemode 0.25 dB/km
The power budgets for the 1300 nm ELED are calcu- Splice losses: One splice every 2 km,
NOTE lated from the manufacturer's transmitter power and at 0.05 dB loss per splice.
receiver sensitivity at ambient temperature. At
extreme temperatures these values deviate based SYSTEM MARGIN
on component tolerance. On average, the output 3 dB additional loss added to calculations to compensate for
all other losses.
power decreases as the temperature is increased by
a factor 1dB / 5°C.
Compensated difference in transmitting and receiving (channel
MAXIMUM OPTICAL INPUT POWER asymmetry) channel delays using GPS satellite clock: 10 ms
EMITTER, FIBER TYPE MAX. OPTICAL
INPUT POWER
820 nm LED, Multimode –7.6 dBm
1300 nm LED, Multimode –11 dBm
1300 nm ELED, Singlemode –14 dBm
1300 nm Laser, Singlemode –14 dBm
1550 nm Laser, Singlemode –14 dBm
2.2.10 ENVIRONMENTAL
AMBIENT TEMPERATURES OTHER

Storage temperature: –40 to 85°C Altitude: 2000 m (maximum)
Operating temperature: –40 to 60°C; the LCD contrast can be Pollution degree: II
impaired at temperatures less than – Overvoltage category: II
20°C
Ingress protection: IP20 front, IP10 back
HUMIDITY
Humidity: operating up to 95% (non-condensing) at
55°C (as per IEC60068-2-30 variant 1, 6
days).

2.2.11 TYPE TESTS
D60 TYPE TESTS

TEST REFERENCE STANDARD TEST LEVEL
Dielectric voltage withstand EN60255-5 2.2 kV
Impulse voltage withstand EN60255-5 5 kV
2 Damped oscillatory
Electrostatic discharge
IEC61000-4-18 / IEC60255-22-1
EN61000-4-2 / IEC60255-22-2
2.5 kV CM, 1 kV DM
Level 3
RF immunity EN61000-4-3 / IEC60255-22-3 Level 3
Fast transient disturbance EN61000-4-4 / IEC60255-22-4 Class A and B
Surge immunity EN61000-4-5 / IEC60255-22-5 Level 3 and 4
Conducted RF immunity EN61000-4-6 / IEC60255-22-6 Level 3
Power frequency immunity EN61000-4-7 / IEC60255-22-7 Class A and B
Voltage interruption and ripple DC IEC60255-11 12% ripple, 200 ms interrupts
Radiated and conducted emissions CISPR11 / CISPR22 / IEC60255-25 Class A
Sinusoidal vibration IEC60255-21-1 Class 1
Shock and bump IEC60255-21-2 Class 1
Seismic IEC60255-21-3 Class 1
Power magnetic immunity IEC61000-4-8 Level 5
Pulse magnetic immunity IEC61000-4-9 Level 4
Damped magnetic immunity IEC61000-4-10 Level 4
Voltage dip and interruption IEC61000-4-11 0, 40, 70, 80% dips; 250 / 300 cycle interrupts
Damped oscillatory IEC61000-4-12 2.5 kV CM, 1 kV DM
Conducted RF immunity, 0 to 150 kHz IEC61000-4-16 Level 4
Voltage ripple IEC61000-4-17 15% ripple
Ingress protection IEC60529 IP40 front, IP10 back
Cold IEC60068-2-1 –40°C for 16 hours
Hot IEC60068-2-2 85°C for 16 hours
Humidity IEC60068-2-30 6 days, variant 1
Damped oscillatory IEEE/ANSI C37.90.1 2.5 kV, 1 MHz
RF immunity IEEE/ANSI C37.90.2 20 V/m, 80 MHz to 1 GHz
Safety UL508 e83849 NKCR
Safety UL C22.2-14 e83849 NKCR7
Safety UL1053 e83849 NKCR
2.2.12 PRODUCTION TESTS
THERMAL
Products go through an environmental test based upon an
Accepted Quality Level (AQL) sampling process.

2.2.13 APPROVALS
APPROVALS
COMPLIANCE APPLICABLE ACCORDING TO
COUNCIL DIRECTIVE
CE Low voltage directive EN 60255-5
EMC directive EN 60255-26 / EN 50263
EN 61000-6-5 2
C-UL-US --- UL 508
UL 1053
C22.2 No. 14
2.2.14 MAINTENANCE
MOUNTING CLEANING
Attach mounting brackets using 20 inch-pounds (±2 inch-pounds) Normally, cleaning is not required; but for situations where dust
of torque. has accumulated on the faceplate display, a dry cloth can be used.
To avoid deterioration of electrolytic
capacitors, power up units that are stored
in a de-energized state once per year, for
one hour continuously.


3 HARDWARE 3.1 DESCRIPTION
3 HARDWARE 3.1DESCRIPTION 3.1.1 PANEL CUTOUT
a) HORIZONTAL UNITS
The D60 Line Distance Protection System is available as a 19-inch rack horizontal mount unit with a removable faceplate.
The faceplate can be specified as either standard or enhanced at the time of ordering. The enhanced faceplate contains
additional user-programmable pushbuttons and LED indicators.
The modular design allows the relay to be easily upgraded or repaired by a qualified service person. The faceplate is
hinged to allow easy access to the removable modules, and is itself removable to allow mounting on doors with limited rear
depth.
The case dimensions are shown below, along with panel cutout details for panel mounting. When planning the location of
your panel cutout, ensure that provision is made for the faceplate to swing open without interference to or from adjacent
equipment.
The relay must be mounted such that the faceplate sits semi-flush with the panel or switchgear door, allowing the operator 3
access to the keypad and the RS232 communications port. The relay is secured to the panel with the use of four screws
supplied with the relay.
11.016”
[279,81 mm]
9.687”
[246,05 mm]
17.56”
[446,02 mm]
7.460”
[189,48 mm]
6.995” 6.960”
[177,67 mm] [176,78 mm]
19.040”
[483,62 mm]
842807A1.CDR
Figure 3–1: D60 HORIZONTAL DIMENSIONS (ENHANCED PANEL)

3.1 DESCRIPTION 3 HARDWARE
18.370”
[466,60 mm]
0.280”
[7,11 mm]
Typ. x 4
CUT-OUT
4.000”
[101,60 mm]
17.750”
3
[450,85 mm] 842808A1.CDR
Figure 3–2: D60 HORIZONTAL MOUNTING (ENHANCED PANEL)
Figure 3–3: D60 HORIZONTAL MOUNTING AND DIMENSIONS (STANDARD PANEL)
b) VERTICAL UNITS
The D60 Line Distance Protection System is available as a reduced size (¾) vertical mount unit, with a removable face-
plate. The faceplate can be specified as either standard or enhanced at the time of ordering. The enhanced faceplate con-
tains additional user-programmable pushbuttons and LED indicators.
The modular design allows the relay to be easily upgraded or repaired by a qualified service person. The faceplate is
hinged to allow easy access to the removable modules, and is itself removable to allow mounting on doors with limited rear
depth.
The case dimensions are shown below, along with panel cutout details for panel mounting. When planning the location of
your panel cutout, ensure that provision is made for the faceplate to swing open without interference to or from adjacent
equipment.

The relay must be mounted such that the faceplate sits semi-flush with the panel or switchgear door, allowing the operator
access to the keypad and the RS232 communications port. The relay is secured to the panel with the use of four screws
supplied with the relay.
7.482” 11.015”
1.329”
13.560”
3
15.000” 14.025”
4.000”
9.780”
843809A1.CDR
Figure 3–4: D60 VERTICAL DIMENSIONS (ENHANCED PANEL)

Figure 3–5: D60 VERTICAL MOUNTING AND DIMENSIONS (STANDARD PANEL)

For details on side mounting D60 devices with the enhanced front panel, refer to the following documents available online
from the GE Multilin website.
• GEK-113180: UR-series UR-V side-mounting front panel assembly instructions.
• GEK-113181: Connecting the side-mounted UR-V enhanced front panel to a vertical UR-series device.
• GEK-113182: Connecting the side-mounted UR-V enhanced front panel to a vertically-mounted horizontal UR-series
device.
For details on side mounting D60 devices with the standard front panel, refer to the figures below.

Figure 3–6: D60 VERTICAL SIDE MOUNTING INSTALLATION (STANDARD PANEL)

Figure 3–7: D60 VERTICAL SIDE MOUNTING REAR DIMENSIONS (STANDARD PANEL)
3.1.2 REAR TERMINAL LAYOUT
Figure 3–8: REAR TERMINAL VIEW

Do not touch any rear terminals while the relay is energized.
The small form-factor pluggable ports (SFPs) are pluggable transceivers. Do not use non-validated
transceivers or install validated transceivers in the wrong Ethernet slot, else damage can occur.
The relay follows a convention with respect to terminal number assignments which are three characters long assigned in
order by module slot position, row number, and column letter. Two-slot wide modules take their slot designation from the
first slot position (nearest to CPU module) which is indicated by an arrow marker on the terminal block. See the following
figure for an example of rear terminal assignments.
Figure 3–9: EXAMPLE OF MODULES IN F AND H SLOTS

3.2 WIRING 3 HARDWARE
3.2WIRING 3.2.1 TYPICAL WIRING
Figure 3–10: TYPICAL WIRING DIAGRAM (T MODULE SHOWN FOR CPU)

3 HARDWARE 3.2 WIRING
3.2.2 DIELECTRIC STRENGTH
The dielectric strength of the UR-series module hardware is shown in the following table:
Table 3–1: DIELECTRIC STRENGTH OF UR-SERIES MODULE HARDWARE
MODULE MODULE FUNCTION TERMINALS DIELECTRIC STRENGTH
TYPE (AC)
FROM TO
1 Power supply High (+); Low (+); (–) Chassis 2000 V AC for 1 minute
1 Power supply 48 V DC (+) and (–) Chassis 2000 V AC for 1 minute
1 Power supply Relay terminals Chassis 2000 V AC for 1 minute
2 Reserved N/A N/A N/A
3 Reserved N/A N/A N/A
4
5
Reserved
Analog inputs/outputs
N/A
All except 8b
N/A
Chassis
N/A
< 50 V DC
3
6 Digital inputs/outputs All Chassis 2000 V AC for 1 minute
G.703 All except 2b, 3a, 7b, 8a Chassis 2000 V AC for 1 minute
7
RS422 All except 6a, 7b, 8a Chassis < 50 V DC
8 CT/VT All Chassis 2000 V AC for 1 minute
9 CPU All Chassis 2000 V AC for 1 minute
Filter networks and transient protection clamps are used in the hardware to prevent damage caused
by high peak voltage transients, radio frequency interference (RFI), and electromagnetic interference
(EMI). These protective components can be damaged by application of the ANSI/IEEE C37.90 spec-
ified test voltage for a period longer than the specified one minute.
3.2.3 CONTROL POWER
Control power supplied to the relay must be connected to the matching power supply range of the
relay. If the voltage is applied to the wrong terminals, damage can occur.
The D60 relay, like almost all electronic relays, contains electrolytic capacitors. These capacitors are
well known to be subject to deterioration over time if voltage is not applied periodically. Deterioration
can be avoided by powering the relays up once a year.
The power supply module can be ordered for two possible voltage ranges, with or without a redundant power option. Each
range has a dedicated input connection for proper operation. The ranges are as shown below (see the Technical specifica-
tions section of chapter 2 for additional details):
• Low (LO) range: 24 to 48 V (DC only) nominal.
• High (HI) range: 125 to 250 V nominal.
The power supply module provides power to the relay and supplies power for dry contact input connections.
The power supply module provides 48 V DC power for dry contact input connections and a critical failure relay (see the
Typical wiring diagram earlier). The critical failure relay is a form-C device that is energized once control power is applied
and the relay has successfully booted up with no critical self-test failures. If on-going self-test diagnostic checks detect a
critical failure (see the Self-test errors section in chapter 7) or control power is lost, the relay is de-energize.
For high reliability systems, the D60 has a redundant option in which two D60 power supplies are placed in parallel on the
bus. If one of the power supplies become faulted, the second power supply assumes the full load of the relay without any
interruptions. Each power supply has a green LED on the front of the module to indicate it is functional. The critical fail relay
of the module also indicates a faulted power supply.
An LED on the front of the control power module shows the status of the power supply:
LED INDICATION POWER SUPPLY
CONTINUOUS ON OK
ON / OFF CYCLING Failure
OFF Failure

Figure 3–11: CONTROL POWER CONNECTION
3.2.4 CT/VT MODULES
A CT/VT module can have voltage inputs on channels 1 through 4 inclusive, or channels 5 through 8 inclusive. Channels 1
and 5 are intended for connection to phase A, and are labeled as such in the relay. Likewise, channels 2 and 6 are intended
for connection to phase B, and channels 3 and 7 are intended for connection to phase C.
Channels 4 and 8 are intended for connection to a single-phase source. For voltage inputs, these channel are labelled as
auxiliary voltage (VX). For current inputs, these channels are intended for connection to a CT between system neutral and
ground, and are labelled as ground current (IG).
Verify that the connection made to the relay nominal current of 1 A or 5 A matches the secondary rat-
ing of the connected CTs. Unmatched CTs may result in equipment damage or inadequate protec-
tion.
CT/VT modules can be ordered with a standard ground current input that is the same as the phase current input. Each AC
current input has an isolating transformer and an automatic shorting mechanism that shorts the input when the module is
withdrawn from the chassis. There are no internal ground connections on the current inputs. Current transformers with 1 to
50000 A primaries and 1 A or 5 A secondaries may be used.
CT/VT modules with a sensitive ground input are also available. The ground CT input of the sensitive ground modules is
ten times more sensitive than the ground CT input of standard CT/VT modules. However, the phase CT inputs and phase
VT inputs are the same as those of regular CT/VT modules.
The above modules are available with enhanced diagnostics. These modules can automatically detect CT/VT hardware
failure and take the relay out of service.
CT connections for both ABC and ACB phase rotations are identical as shown in the Typical wiring diagram.
The exact placement of a zero-sequence core balance CT to detect ground fault current is shown below. Twisted-pair
cabling on the zero-sequence CT is recommended.

Figure 3–12: ZERO-SEQUENCE CORE BALANCE CT INSTALLATION

The phase voltage channels are used for most metering and protection purposes. The auxiliary voltage channel is used as
input for the synchrocheck and volts-per-hertz features.
Substitute the tilde “~” symbol with the slot position of the module in the following figure.
NOTE
Figure 3–13: CT/VT MODULE WIRING
3.2.5 PROCESS BUS MODULES
The D60 can be ordered with a process bus interface module. This module is designed to interface with the GE Multilin
HardFiber system, allowing bidirectional IEC 61850 fiber optic communications with up to eight HardFiber merging units,
known as Bricks. The HardFiber system has been designed to integrate seamlessly with the existing UR-series applica-
tions, including protection functions, FlexLogic, metering, and communications.
The IEC 61850 process bus system offers the following benefits:
• Reduces labor associated with design, installation, and testing of protection and control applications using the D60 by
reducing the number of individual copper terminations
• Integrates seamlessly with existing D60 applications, since the IEC 61850 process bus interface module replaces the
traditional CT/VT modules
• Communicates using open standard IEC 61850 messaging
For additional details on the HardFiber system, see GE publication GEK-113658: HardFiber Process Bus System Instruc-
tion Manual.

3.2.6 CONTACT INPUTS AND OUTPUTS
Every contact input/output module has 24 terminal connections. They are arranged as three terminals per row, with eight
rows in total. A given row of three terminals can be used for the outputs of one relay. For example, for form-C relay outputs,
the terminals connect to the normally open (NO), normally closed (NC), and common contacts of the relay. For a form-A
output, there are options of using current or voltage detection for feature supervision, depending on the module ordered.
The terminal configuration for contact inputs is different for the two applications.
The contact inputs are grouped with a common return. The D60 has two versions of grouping: four inputs per common
return and two inputs per common return. When a contact input/output module is ordered, four inputs per common is used.
The four inputs per common allows for high-density inputs in combination with outputs, with a compromise of four inputs
sharing one common. If the inputs must be isolated per row, then two inputs per common return should be selected (4D
module).
3 The tables and diagrams on the following pages illustrate the module types (6A, etc.) and contact arrangements that can be
ordered for the relay. Since an entire row is used for a single contact output, the name is assigned using the module slot
position and row number. However, since there are two contact inputs per row, these names are assigned by module slot
position, row number, and column position.
Some form-A / solid-state relay outputs include circuits to monitor the DC voltage across the output contact when it is open,
and the DC current through the output contact when it is closed. Each of the monitors contains a level detector whose out-
put is set to logic “On = 1” when the current in the circuit is above the threshold setting. The voltage monitor is set to “On =
1” when the current is above about 1 to 2.5 mA, and the current monitor is set to “On = 1” when the current exceeds about
80 to 100 mA. The voltage monitor is intended to check the health of the overall trip circuit, and the current monitor can be
used to seal-in the output contact until an external contact has interrupted current flow.
Block diagrams are shown as follows for form-A and solid-state relay outputs with optional voltage monitor, optional current
monitor, and with no monitoring. The actual values shown for contact output 1 are the same for all contact outputs.
,I,GFP$&RQW2S ´,2Qµ
aD aD RWKHUZLVH&RQW2S ´,2IIµ
, , ,I,GFP$&RQW2S ´92Qµ
RWKHUZLVH&RQW2S ´92IIµ
,I,GFP$&RQW2S ´92Qµ
aE aE /RDG
9 /RDG 9
aF aF
D 9ROWDJHZLWKRSWLRQDO
9ROWDJHPRQLWRULQJRQO\ %RWKYROWDJHDQGFXUUHQWPRQLWRULQJ
FXUUHQWPRQLWRULQJ
aD aD RWKHUZLVH&RQW2S ´,2IIµ
9 9 ,I,GFP$&RQW2S ´92Qµ
, aE , aE /RDG
RWKHUZLVH&RQW2S ´,2IIµ
/RDG
aF aF
E &XUUHQWZLWKRSWLRQDO
&XUUHQWPRQLWRULQJRQO\ %RWKYROWDJHDQGFXUUHQWPRQLWRULQJ
YROWDJHPRQLWRULQJ
H[WHUQDOMXPSHUDELVUHTXLUHG
aD
aE
/RDG
aF
F 1RPRQLWRULQJ $&'5
Figure 3–14: FORM-A AND SOLID-STATE CONTACT OUTPUTS WITH VOLTAGE AND CURRENT MONITORING

The operation of voltage and current monitors is reflected with the corresponding FlexLogic operands (CONT OP # VON,
CONT OP # VOFF, and CONT OP # ION) which can be used in protection, control, and alarm logic. The typical application of
the voltage monitor is breaker trip circuit integrity monitoring; a typical application of the current monitor is seal-in of the
control command.
Refer to the Digital elements section of chapter 5 for an example of how form-A and solid-state relay contacts can be
applied for breaker trip circuit integrity monitoring.
Consider relay contacts unsafe to touch when the unit is energized. If the relay contacts need
to be used for low voltage accessible applications, ensure proper insulation levels.
USE OF FORM-A AND SOLID-STATE RELAY OUTPUTS IN HIGH IMPEDANCE CIRCUITS
NOTE For form-A and solid-state relay output contacts internally equipped with a voltage measuring circuit across the con-
tact, the circuit has an impedance that can cause a problem when used in conjunction with external high input
impedance monitoring equipment such as modern relay test set trigger circuits. These monitoring circuits may con-
3
tinue to read the form-A contact as being closed after it has closed and subsequently opened, when measured as
an impedance.
The solution is to use the voltage measuring trigger input of the relay test set, and connect the form-A contact
through a voltage-dropping resistor to a DC voltage source. If the 48 V DC output of the power supply is used as a
source, a 500 , 10 W resistor is appropriate. In this configuration, the voltage across either the form-A contact or
the resistor can be used to monitor the state of the output.
Wherever a tilde “~” symbol appears, substitute with the slot position of the module; wherever a number sign “#”
appears, substitute the contact number
NOTE
When current monitoring is used to seal-in the form-A and solid-state relay contact outputs, the Flex-
Logic operand driving the contact output should be given a reset delay of 10 ms to prevent damage
of the output contact (in situations when the element initiating the contact output is bouncing, at val-
ues in the region of the pickup value).
Table 3–2: CONTACT INPUT AND OUTPUT MODULE ASSIGNMENTS

~6A MODULE ~6B MODULE ~6C MODULE ~6D MODULE
TERMINAL OUTPUT OR TERMINAL OUTPUT OR TERMINAL OUTPUT TERMINAL OUTPUT
ASSIGNMENT INPUT ASSIGNMENT INPUT ASSIGNMENT ASSIGNMENT
~1 Form-A ~1 Form-A ~1 Form-C ~1a, ~1c 2 Inputs
~2 Form-A ~2 Form-A ~2 Form-C ~2a, ~2c 2 Inputs
~3 Form-C ~3 Form-C ~3 Form-C ~3a, ~3c 2 Inputs
~4 Form-C ~4 Form-C ~4 Form-C ~4a, ~4c 2 Inputs
~5a, ~5c 2 Inputs ~5 Form-C ~5 Form-C ~5a, ~5c 2 Inputs
~6a, ~6c 2 Inputs ~6 Form-C ~6 Form-C ~6a, ~6c 2 Inputs
~7a, ~7c 2 Inputs ~7a, ~7c 2 Inputs ~7 Form-C ~7a, ~7c 2 Inputs
~8a, ~8c 2 Inputs ~8a, ~8c 2 Inputs ~8 Form-C ~8a, ~8c 2 Inputs
~6E MODULE ~6F MODULE ~6G MODULE ~6H MODULE

TERMINAL OUTPUT OR TERMINAL OUTPUT TERMINAL OUTPUT OR TERMINAL OUTPUT OR
ASSIGNMENT INPUT ASSIGNMENT ASSIGNMENT INPUT ASSIGNMENT INPUT
~1 Form-C ~1 Fast Form-C ~1 Form-A ~1 Form-A
~5a, ~5c 2 Inputs ~5 Fast Form-C ~5a, ~5c 2 Inputs ~5 Form-A
~6a, ~6c 2 Inputs ~6 Fast Form-C ~6a, ~6c 2 Inputs ~6 Form-A
~7a, ~7c 2 Inputs ~7 Fast Form-C ~7a, ~7c 2 Inputs ~7a, ~7c 2 Inputs
~8a, ~8c 2 Inputs ~8 Fast Form-C ~8a, ~8c 2 Inputs ~8a, ~8c 2 Inputs

~6K MODULE ~6L MODULE ~6M MODULE ~6N MODULE

TERMINAL OUTPUT TERMINAL OUTPUT OR TERMINAL OUTPUT OR TERMINAL OUTPUT OR
ASSIGNMENT ASSIGNMENT INPUT ASSIGNMENT INPUT ASSIGNMENT INPUT
~1 Form-C ~1 Form-A ~1 Form-A ~1 Form-A
~2 Form-C ~2 Form-A ~2 Form-A ~2 Form-A
~3 Form-C ~3 Form-C ~3 Form-C ~3 Form-A
~4 Form-C ~4 Form-C ~4 Form-C ~4 Form-A
~5 Fast Form-C ~5a, ~5c 2 Inputs ~5 Form-C ~5a, ~5c 2 Inputs
~6 Fast Form-C ~6a, ~6c 2 Inputs ~6 Form-C ~6a, ~6c 2 Inputs
~7 Fast Form-C ~7a, ~7c 2 Inputs ~7a, ~7c 2 Inputs ~7a, ~7c 2 Inputs
~8 Fast Form-C ~8a, ~8c 2 Inputs ~8a, ~8c 2 Inputs ~8a, ~8c 2 Inputs
3
~6P MODULE ~6R MODULE ~6S MODULE ~6T MODULE
TERMINAL OUTPUT OR TERMINAL OUTPUT OR TERMINAL OUTPUT OR TERMINAL OUTPUT OR
ASSIGNMENT INPUT ASSIGNMENT INPUT ASSIGNMENT INPUT ASSIGNMENT INPUT
~1 Form-A ~1 Form-A ~1 Form-A ~1 Form-A
~2 Form-A ~2 Form-A ~2 Form-A ~2 Form-A
~3 Form-A ~3 Form-C ~3 Form-C ~3 Form-A
~4 Form-A ~4 Form-C ~4 Form-C ~4 Form-A
~5 Form-A ~5a, ~5c 2 Inputs ~5 Form-C ~5a, ~5c 2 Inputs
~6 Form-A ~6a, ~6c 2 Inputs ~6 Form-C ~6a, ~6c 2 Inputs
~7a, ~7c 2 Inputs ~7a, ~7c 2 Inputs ~7a, ~7c 2 Inputs ~7a, ~7c 2 Inputs
~8a, ~8c 2 Inputs ~8a, ~8c 2 Inputs ~8a, ~8c 2 Inputs ~8a, ~8c 2 Inputs
~6U MODULE ~6V MODULE ~67 MODULE ~4A MODULE

TERMINAL OUTPUT OR TERMINAL OUTPUT OR TERMINAL OUTPUT TERMINAL OUTPUT
ASSIGNMENT INPUT ASSIGNMENT INPUT ASSIGNMENT ASSIGNMENT
~1 Form-A ~1 Form-A ~1 Form-A ~1 Not Used
~2 Form-A ~2 Form-A ~2 Form-A ~2 Solid-State
~3 Form-A ~3 Form-C ~3 Form-A ~3 Not Used
~4 Form-A ~4 2 Outputs ~4 Form-A ~4 Solid-State
~5 Form-A ~5a, ~5c 2 Inputs ~5 Form-A ~5 Not Used
~6 Form-A ~6a, ~6c 2 Inputs ~6 Form-A ~6 Solid-State
~7a, ~7c 2 Inputs ~7a, ~7c 2 Inputs ~7 Form-A ~7 Not Used
~8a, ~8c 2 Inputs ~8a, ~8c 2 Inputs ~8 Form-A ~8 Solid-State
~4B MODULE ~4C MODULE ~4D MODULE ~4L MODULE

TERMINAL OUTPUT TERMINAL OUTPUT TERMINAL OUTPUT TERMINAL OUTPUT
ASSIGNMENT ASSIGNMENT ASSIGNMENT ASSIGNMENT
~1 Not Used ~1 Not Used ~1a, ~1c 2 Inputs ~1 2 Outputs
~2 Solid-State ~2 Solid-State ~2a, ~2c 2 Inputs ~2 2 Outputs
~8 Solid-State ~8 Solid-State ~8a, ~8c 2 Inputs ~8 Not Used

Figure 3–15: CONTACT INPUT AND OUTPUT MODULE WIRING (1 of 2)

~ 1a ~ 5a CONTACT IN ~ 5a DIGITAL I/O 6L V ~ 1a ~ 7a CONTACT IN ~ 7a DIGITAL I/O 6M V ~ 1a
6K
I I
~ 1b ~1 ~ 5c CONTACT IN ~ 5c ~1 ~ 1b ~ 7c CONTACT IN ~ 7c ~1 ~ 1b
~ 1c ~ 6a CONTACT IN ~ 6a ~ 1c ~ 8a CONTACT IN ~ 8a ~ 1c
~ 2a ~ 6c CONTACT IN ~ 6c V ~ 2a ~ 8c CONTACT IN ~ 8c V ~ 2a
I I
~ 2b ~2 ~ 5b COMMON ~ 5b ~2 ~ 2b ~ 7b COMMON ~ 7b ~2 ~ 2b
~ 2c ~ 2c ~ 2c
~ 7a CONTACT IN ~ 7a ~ 8b SURGE
~ 3a ~ 3a ~ 3a
~ 7c CONTACT IN ~ 7c
~ 3b ~3 ~3 ~ 3b ~3 ~ 3b
~ 8a CONTACT IN ~ 8a
~ 3c ~ 3c ~ 3c
~ 4a ~ 4a ~ 4a
~ 7b COMMON ~ 7b
~ 4b ~4 ~4 ~ 4b ~4 ~ 4b
~ 4c ~ 8b SURGE ~ 4c ~ 4c
~ 5a ~ 5a
~ 5b ~5 ~5 ~ 5b
~ 5c ~ 5c
~ 6a ~ 6a
~ 6b ~6 ~6 ~ 6b
~ 6c ~ 6c
3
~ 7a
DIGITAL I/O
~ 7b ~7
~ 7c
~ 8a
~ 8b ~8
~ 8c
~ 5a CONTACT IN ~ 5a DIGITAL I/O 6N V ~ 1a ~ 7a CONTACT IN ~ 7a DIGITAL I/O 6P V ~ 1a

I I
~ 5c CONTACT IN ~ 5c ~1 ~ 1b ~ 7c CONTACT IN ~ 7c ~1 ~ 1b
~ 6a CONTACT IN ~ 6a ~ 1c ~ 8a CONTACT IN ~ 8a ~ 1c
~ 6c CONTACT IN ~ 6c V ~ 2a ~ 8c CONTACT IN ~ 8c V ~ 2a
I I
~ 5b COMMON ~ 5b ~2 ~ 2b ~ 7b COMMON ~ 7b ~2 ~ 2b
~ 2c ~ 2c
~ 7a CONTACT IN ~ 7a ~ 8b SURGE
V ~ 3a V ~ 3a
~ 7c CONTACT IN ~ 7c I I
~3 ~ 3b ~3 ~ 3b
~ 3c ~ 3c
V ~ 4a V ~ 4a
~ 7b COMMON ~ 7b I I
~4 ~ 4b ~4 ~ 4b
~ 8b SURGE ~ 4c ~ 4c
V ~ 5a
I
~5 ~ 5b
~ 5c
V ~ 6a
I
~6 ~ 6b
~ 5a CONTACT IN ~ 5a DIGITAL I/O 6R ~ 1a
~ 6c
~ 5c CONTACT IN ~ 5c ~1 ~ 1b
~ 6a CONTACT IN ~ 6a ~ 1c
~ 6c CONTACT IN ~ 6c ~ 2a
~ 5b COMMON ~ 5b ~2 ~ 2b
~ 2c ~ 7a CONTACT IN ~ 7a DIGITAL I/O 6S ~ 1a
~ 3a ~ 7c CONTACT IN ~ 7c ~1 ~ 1b
~3 ~ 3b ~ 8a CONTACT IN ~ 8a ~ 1c
~ 3c ~ 8c CONTACT IN ~ 8c ~ 2a
~ 4a ~ 7b COMMON ~ 7b ~2 ~ 2b
~ 7b COMMON ~ 7b
~4 ~ 4b ~ 2c
~ 8b SURGE ~ 4c ~ 8b SURGE
~ 3a
~3 ~ 3b
~ 3c
~ 4a
~4 ~ 4b
~ 5a CONTACT IN ~ 5a DIGITAL I/O 6T ~ 1a ~ 4c
~ 5c CONTACT IN ~ 5c ~1 ~ 1b ~ 5a
~ 6a CONTACT IN ~ 6a ~ 1c ~5 ~ 5b
~ 6c CONTACT IN ~ 6c ~ 2a ~ 5c
~ 5b COMMON ~ 5b ~2 ~ 2b ~ 6a
~ 2c ~6 ~ 6b
~ 3a
~3 ~ 3b
~ 3c
~ 4a
~ 7b COMMON ~ 7b
~4 ~ 4b
~ 7a CONTACT IN ~ 7a DIGITAL I/O 6U ~ 1a
~ 8b SURGE ~ 4c
~ 7c CONTACT IN ~ 7c ~1 ~ 1b
~ 8c CONTACT IN ~ 8c ~ 2a
~ 7b COMMON ~ 7b ~2 ~ 2b
~ 2c
~ 8b SURGE
~ 3a
~3 ~ 3b
~ 3c
~ 4a
~4 ~ 4b
~ 4c
~ 5a
~5 ~ 5b
~ 5c
~ 6a
~6 ~ 6b
~ 6c
842763A2.CDR
Figure 3–16: CONTACT INPUT AND OUTPUT MODULE WIRING (2 of 2)

For proper functionality, observe correct polarity for all contact input and solid state output connec-
tions.

CONTACT INPUTS
A dry contact has one side connected to terminal B3b. This is the positive 48 V DC voltage rail supplied by the power sup-
ply module. The other side of the dry contact is connected to the required contact input terminal. Each contact input group
has its own common (negative) terminal which must be connected to the DC negative terminal (B3a) of the power supply
module. When a dry contact closes, a current of 1 to 3 mA flows through the associated circuit.
A wet contact has one side connected to the positive terminal of an external DC power supply. The other side of this contact
is connected to the required contact input terminal. If a wet contact is used, then the negative side of the external source
must be connected to the relay common (negative) terminal of each contact group. The maximum external source voltage
for this arrangement is 300 V DC.
The voltage threshold at which each group of four contact inputs detects a closed contact input is programmable as
17 V DC for 24 V sources, 33 V DC for 48 V sources, 84 V DC for 110 to 125 V sources, and 166 V DC for 250 V sources.
Figure 3–17: DRY AND WET CONTACT INPUT CONNECTIONS

Wherever a tilde “~” symbol appears, substitute with the slot position of the module.
NOTE
Contact outputs can be ordered as form-A or form-C. The form-A contacts can be connected for external circuit supervi-
sion. These contacts are provided with voltage and current monitoring circuits used to detect the loss of DC voltage in the
circuit, and the presence of DC current flowing through the contacts when the form-A contact closes. If enabled, the current
monitoring can be used as a seal-in signal to ensure that the form-A contact does not attempt to break the energized induc-
tive coil circuit and weld the output contacts.
There is no provision in the relay to detect a DC ground fault on 48 V DC control power external output. We recom-
mend using an external DC supply.
NOTE

USE OF CONTACT INPUTS WITH AUTO-BURNISHING

The contact inputs sense a change of the state of the external device contact based on the measured current. When exter-
nal devices are located in a harsh industrial environment (either outdoor or indoor), their contacts can be exposed to vari-
ous types of contamination. Normally, there is a thin film of insulating sulfidation, oxidation, or contaminates on the surface
of the contacts, sometimes making it difficult or impossible to detect a change of the state. This film must be removed to
establish circuit continuity – an impulse of higher than normal current can accomplish this.
The contact inputs with auto-burnish create a high current impulse when the threshold is reached to burn off this oxidation
layer as a maintenance to the contacts. Afterwards the contact input current is reduced to a steady-state current. The
impulse has a 5 second delay after a contact input changes state.
current
50 to 70 mA
3 mA
time
25 to 50 ms 842749A1.CDR
Figure 3–18: CURRENT THROUGH CONTACT INPUTS WITH AUTO-BURNISHING

Regular contact inputs limit current to less than 3 mA to reduce station battery burden. In contrast, contact inputs with auto-
burnishing allow currents up to 50 to 70 mA at the first instance when the change of state was sensed. Then, within 25 to
50 ms, this current is slowly reduced to 3 mA as indicated above. The 50 to 70 mA peak current burns any film on the con-
tacts, allowing for proper sensing of state changes. If the external device contact is bouncing, the auto-burnishing starts
when external device contact bouncing is over.
Another important difference between the auto-burnishing input module and the regular input modules is that only two con-
tact inputs have common ground, as opposed to four contact inputs sharing one common ground (refer to the Contact Input
and Output Module Wiring diagrams). This is beneficial when connecting contact inputs to separate voltage sources. Con-
sequently, the threshold voltage setting is also defined per group of two contact inputs.
The auto-burnish feature can be disabled or enabled using the DIP switches found on each daughter card. There is a DIP
switch for each contact, for a total of 16 inputs.
CONTACT INPUT 1 AUTO-BURNISH = OFF

CONTACT INPUT 1 AUTO-BURNISH = ON



842751A1.CDR
Figure 3–19: AUTO-BURNISH DIP SWITCHES

The auto-burnish circuitry has an internal fuse for safety purposes. During regular maintenance, check the auto-
burnish functionality using an oscilloscope.
NOTE

3.2.7 TRANSDUCER INPUTS/OUTPUTS
Transducer input modules can receive input signals from external dcmA output transducers (dcmA In) or resistance tem-
perature detectors (RTD). Hardware and software is provided to receive signals from these external transducers and con-
vert these signals into a digital format for use as required.
Transducer output modules provide DC current outputs in several standard dcmA ranges. Software is provided to configure
virtually any analog quantity used in the relay to drive the analog outputs.
Every transducer input/output module has a total of 24 terminal connections. These connections are arranged as three ter-
minals per row with a total of eight rows. A given row can be used for either inputs or outputs, with terminals in column "a"
having positive polarity and terminals in column "c" having negative polarity. Since an entire row is used for a single input/
output channel, the name of the channel is assigned using the module slot position and row number.
Each module also requires that a connection from an external ground bus be made to terminal 8b. The current outputs
3 require a twisted-pair shielded cable, where the shield is grounded at one end only. The figure below illustrates the trans-
ducer module types (5A, 5C, 5D, 5E, and 5F) and channel arrangements that can be ordered for the relay.
Wherever a tilde “~” symbol appears, substitute with the slot position of the module.
NOTE
Figure 3–20: TRANSDUCER INPUT/OUTPUT MODULE WIRING

3.2.8 RS232 FACEPLATE PORT
A 9-pin RS232C serial port is located on the D60 faceplate for programming with a computer. All that is required to use this
interface is a computer running the EnerVista UR Setup software provided with the relay. Cabling for the RS232 port is
shown in the following figure for both 9-pin and 25-pin connectors.
The baud rate for this port is fixed at 19200 bps.
NOTE
Figure 3–21: RS232 FACEPLATE PORT CONNECTION
3.2.9 CPU COMMUNICATION PORTS
a) OPTIONS
In addition to the faceplate RS232 port, the D60 provides a rear RS485 communication port.
The CPU modules do not require a surge ground connection.
NOTE

Figure 3–22: CPU MODULE COMMUNICATIONS WIRING
b) RS485 PORTS
RS485 data transmission and reception are accomplished over a single twisted pair with transmit and receive data alternat-
ing over the same two wires. Through the use of the port, continuous monitoring and control from a remote computer,
SCADA system, or PLC is possible.
To minimize errors from noise, the use of shielded twisted pair wire is recommended. Correct polarity must also be
observed. For instance, the relays must be connected with all RS485 “+” terminals connected together, and all RS485 “–”
terminals connected together. Though data is transmitted over a two-wire twisted pair, all RS485 devices require a shared
reference, or common voltage. This common voltage is implied to be a power supply common. Some systems allow the
shield (drain wire) to be used as common wire and to connect directly to the D60 COM terminal (#3); others function cor-
rectly only if the common wire is connected to the D60 COM terminal, but insulated from the shield.
To avoid loop currents, ground the shield at only one point. If other system considerations require the shield to be grounded
at more than one point, install resistors (typically 100 ohms) between the shield and ground at each grounding point. Each
relay needs to be daisy-chained to the next one in the link. A maximum of 32 relays can be connected in this manner with-
out exceeding driver capability. For larger systems, additional serial channels must be added. It is also possible to use com-
mercially available repeaters to have more than 32 relays on a single channel. Avoid star or stub connections entirely.

Lightning strikes and ground surge currents can cause large momentary voltage differences between remote ends of the
communication link. For this reason, surge protection devices are internally provided at both communication ports. An iso-
lated power supply with an optocoupled data interface also acts to reduce noise coupling. To ensure maximum reliability, all
equipment should have similar transient protection devices installed.
Terminate both ends of the RS485 circuit with an impedance as shown below.
Figure 3–23: RS485 SERIAL CONNECTION
c) 100BASE-FX FIBER OPTIC PORTS

Ensure that the dust covers are installed when the fiber is not in use. Dirty or scratched connectors can lead to high
losses on a fiber link.
NOTE
Observing any fiber transmitter output can injure the eye.
The fiber optic communication ports allow for fast and efficient communications between relays at 100 Mbps. Optical fiber
can be connected to the relay supporting a wavelength of 1310 nm in multi-mode.
The fiber optic port is designed such that the response times do not vary for any core that is 100 µm or less in diameter,
62.5 µm for 100 Mbps. For optical power budgeting, splices are required every 1 km for the transmitter/receiver pair. When
splicing optical fibers, the diameter and numerical aperture of each fiber must be the same.

3.2.10 IRIG-B
IRIG-B is a standard time code format that allows stamping of events to be synchronized among connected devices within
1 millisecond. The IRIG time code formats are serial, width-modulated codes that can be either DC level shifted or ampli-
tude modulated (AM). Third party equipment is available for generating the IRIG-B signal; this equipment can use a GPS
satellite system to obtain the time reference so that devices at different geographic locations can be synchronized.
Figure 3–24: OPTIONS FOR THE IRIG-B CONNECTION

Using an amplitude modulated receiver causes errors up to 1 ms in event time-stamping.
NOTE
Using an amplitude modulated receiver also causes errors of up to 1 ms in metered synchrophasor values.
NOTE

3 HARDWARE 3.3 DIRECT INPUT AND OUTPUT COMMUNICATIONS
3.3DIRECT INPUT AND OUTPUT COMMUNICATIONS 3.3.1 DESCRIPTION
The D60 direct inputs and outputs feature makes use of the type 7 series of communications modules, which allow direct
messaging between devices.
The communications channels are normally connected in a ring configuration as shown in the following figure. The trans-
mitter of one module is connected to the receiver of the next module. The transmitter of this second module is then con-
nected to the receiver of the next module in the ring. This is continued to form a communications ring. The figure illustrates
a ring of four UR-series relays with the following connections: UR1-Tx to UR2-Rx, UR2-Tx to UR3-Rx, UR3-Tx to UR4-Rx,
and UR4-Tx to UR1-Rx. A maximum of sixteen (16) UR-series relays can be connected in a single ring
Figure 3–25: DIRECT INPUT AND OUTPUT SINGLE CHANNEL CONNECTION

The interconnection for dual-channel Type 7 communications modules is shown as follows. Two channel modules allow for
a redundant ring configuration. That is, two rings can be created to provide an additional independent data path. The
required connections are: UR1-Tx1 to UR2-Rx1, UR2-Tx1 to UR3-Rx1, UR3-Tx1 to UR4-Rx1, and UR4-Tx1 to UR1-Rx1
for the first ring; and UR1-Tx2 to UR4-Rx2, UR4-Tx2 to UR3-Rx2, UR3-Tx2 to UR2-Rx2, and UR2-Tx2 to UR1-Rx2 for the
second ring.
Figure 3–26: DIRECT INPUT AND OUTPUT DUAL CHANNEL CONNECTION

The following diagram shows the connection for three UR-series relays using two independent communication channels.
UR1 and UR3 have single type 7 communication modules; UR2 has a dual-channel module. The two communication chan-
nels can be of different types, depending on the Type 7 modules used. To allow the direct input and output data to cross-
over from channel 1 to channel 2 on UR2, the DIRECT I/O CHANNEL CROSSOVER setting should be “Enabled” on UR2. This
forces UR2 to forward messages received on Rx1 out Tx2, and messages received on Rx2 out Tx1.

3.3 DIRECT INPUT AND OUTPUT COMMUNICATIONS 3 HARDWARE
3
Figure 3–27: DIRECT INPUT AND OUTPUT SINGLE/DUAL CHANNEL COMBINATION CONNECTION
The interconnection requirements are described in further detail in this section for each specific variation of type 7 commu-
nications module. These modules are listed in the following table. All fiber modules use ST type connectors.
Not all the direct input and output communications modules may be applicable to the D60 relay. Only the modules
specified in the order codes are available as direct input and output communications modules.
NOTE
Table 3–3: CHANNEL COMMUNICATION OPTIONS (Sheet 1 of 2)

MODULE SPECIFICATION
2A C37.94SM, 1300 nm, single-mode, ELED, 1 channel single-mode
2B C37.94SM, 1300 nm, single-mode, ELED, 2 channel single-mode
2E Bi-phase, 1 channel
2F Bi-phase, 2 channel
2G IEEE C37.94, 820 nm, 128 kbps, multi-mode, LED, 1 channel
2H IEEE C37.94, 820 nm, 128 kbps, multi-mode, LED, 2 channels
72 1550 nm, single-mode, laser, 1 channel
73 1550 nm, single-mode, laser, 2 channels
74 Channel 1 - RS422; channel 2 - 1550 nm, single-mode, laser
75 Channel 1 - G.703; channel 2 - 1550 nm, single-mode, laser
76 IEEE C37.94, 820 nm, 64 kbps, multi-mode, LED, 1 channel
77 IEEE C37.94, 820 nm, 64 kbps, multi-mode, LED, 2 channels
7A 820 nm, multi-mode, LED, 1 channel
7B 1300 nm, multi-mode, LED, 1 channel
7C 1300 nm, single-mode, ELED, 1 channel
7D 1300 nm, single-mode, laser, 1 channel
7E Channel 1: G.703, Channel 2: 820 nm, multi-mode
7F Channel 1: G.703, Channel 2: 1300 nm, multi-mode
7G Channel 1: G.703, Channel 2: 1300 nm, single-mode ELED
7H 820 nm, multi-mode, LED, 2 channels
7I 1300 nm, multi-mode, LED, 2 channels
7J 1300 nm, single-mode, ELED, 2 channels
7K 1300 nm, single-mode, LASER, 2 channels
7L Channel 1: RS422, channel: 820 nm, multi-mode, LED
7M Channel 1: RS422, channel 2: 1300 nm, multi-mode, LED
7N Channel 1: RS422, channel 2: 1300 nm, single-mode, ELED
7P Channel 1: RS422, channel 2: 1300 nm, single-mode, laser

Table 3–3: CHANNEL COMMUNICATION OPTIONS (Sheet 2 of 2)

MODULE SPECIFICATION
7Q Channel 1: G.703, channel 2: 1300 nm, single-mode, laser
7R G.703, 1 channel
7S G.703, 2 channels
7T RS422, 1 channel
7V RS422, 2 channels, 2 clock inputs
7W RS422, 2 channels
3.3.2 FIBER: LED AND ELED TRANSMITTERS
The following figure shows the configuration for the 7A, 7B, 7C, 7H, 7I, and 7J fiber-only modules.
3
Figure 3–28: LED AND ELED FIBER MODULES
3.3.3 FIBER-LASER TRANSMITTERS
The following figure shows the configuration for the 72, 73, 7D, and 7K fiber-laser module.
Figure 3–29: LASER FIBER MODULES

When using a laser Interface, attenuators can be necessary to ensure that you do not exceed the
maximum optical input power to the receiver.

3.3.4 G.703 INTERFACE
a) DESCRIPTION
The following figure shows the 64K ITU G.703 co-directional interface configuration.
The G.703 module is fixed at 64 kbps. The SETTINGS > PRODUCT SETUP > DIRECT I/O > DIRECT I/O DATA
RATE setting is not applicable to this module.
NOTE
AWG 24 twisted shielded pair is recommended for external connections, with the shield grounded only at one end. Con-
necting the shield to pin X1a or X6a grounds the shield since these pins are internally connected to ground. Thus, if pin X1a
or X6a is used, do not ground at the other end. This interface module is protected by surge suppression devices.
Figure 3–30: G.703 INTERFACE CONFIGURATION

The following figure shows the typical pin interconnection between two G.703 interfaces. For the actual physical arrange-
ment of these pins, see the Rear terminal assignments section earlier in this chapter. All pin interconnections are to be
maintained for a connection to a multiplexer.
Figure 3–31: TYPICAL PIN INTERCONNECTION BETWEEN TWO G.703 INTERFACES

Pin nomenclature can differ from one manufacturer to another. Therefore, it is not uncommon to see pinouts num-
bered TxA, TxB, RxA and RxB. In such cases, it can be assumed that “A” is equivalent to “+” and “B” is equivalent
NOTE
to “–”.
b) G.703 SELECTION SWITCH PROCEDURES

1. With the power to the relay off, remove the G.703 module (7R or 7S) as follows. Record the original location of the
module to help ensure that the same or replacement module is inserted into the correct slot.
2. Simultaneously pull the ejector/inserter clips located at the top and at the bottom of each module in order to release the
module for removal.
3. Remove the module cover screw.
4. Remove the top cover by sliding it towards the rear and then lift it upwards.
5. Set the timing selection switches (channel 1, channel 2) to the desired timing modes.
6. Replace the top cover and the cover screw.

7. Re-insert the G.703 module. Take care to ensure that the correct module type is inserted into the correct slot position.
The ejector/inserter clips located at the top and at the bottom of each module must be in the disengaged position as
the module is smoothly inserted into the slot. Once the clips have cleared the raised edge of the chassis, engage the
clips simultaneously. When the clips have locked into position, the module is fully inserted.
Figure 3–32: G.703 TIMING SELECTION SWITCH SETTING
Table 3–4: G.703 TIMING SELECTIONS

SWITCHES FUNCTION
S1 OFF octet timing disabled
ON octet timing 8 kHz
S5 and S6 S5 = OFF and S6 = OFF loop timing mode
S5 = ON and S6 = OFF internal timing mode
S5 = OFF and S6 = ON minimum remote loopback mode
S5 = ON and S6 = ON dual loopback mode
c) G.703 OCTET TIMING

If octet timing is enabled (ON), this 8 kHz signal is asserted during the violation of bit 8 (LSB) necessary for connecting to
higher order systems. When D60s are connected back-to-back, octet timing is disabled (OFF).
d) G.703 TIMING MODES

There are two timing modes for the G.703 module: internal timing mode and loop timing mode (default).
• Internal Timing Mode: The system clock is generated internally. Therefore, the G.703 timing selection should be in
the internal timing mode for back-to-back (UR-to-UR) connections. For back-to-back connections, set for octet timing
(S1 = OFF) and timing mode to internal timing (S5 = ON and S6 = OFF).
• Loop Timing Mode: The system clock is derived from the received line signal. Therefore, the G.703 timing selection
should be in loop timing mode for connections to higher order systems. For connection to a higher order system (UR-
to-multiplexer, factory defaults), set to octet timing (S1 = ON) and set timing mode to loop timing (S5 = OFF and S6 =
OFF).

The switch settings for the internal and loop timing modes are shown below:
e) G.703 TEST MODES

3 In minimum remote loopback mode, the multiplexer is enabled to return the data from the external interface without any
processing to assist in diagnosing G.703 line-side problems irrespective of clock rate. Data enters from the G.703 inputs,
passes through the data stabilization latch which also restores the proper signal polarity, passes through the multiplexer
and then returns to the transmitter. The differential received data is processed and passed to the G.703 transmitter module
after which point the data is discarded. The G.703 receiver module is fully functional and continues to process data and
passes it to the differential Manchester transmitter module. Since timing is returned as it is received, the timing source is
expected to be from the G.703 line side of the interface.
DMR = Differential Manchester Receiver

DMR G7X DMX = Differential Manchester Transmitter
G7X = G.703 Transmitter
G7R = G.703 Receiver
DMX G7R
842774A1.CDR
Figure 3–33: G.703 MINIMUM REMOTE LOOPBACK MODE

In dual loopback mode, the multiplexers are active and the functions of the circuit are divided into two with each receiver/
transmitter pair linked together to deconstruct and then reconstruct their respective signals. Differential Manchester data
enters the Differential Manchester receiver module and then is returned to the differential Manchester transmitter module.
Likewise, G.703 data enters the G.703 receiver module and is passed through to the G.703 transmitter module to be
returned as G.703 data. Because of the complete split in the communications path and because, in each case, the clocks
are extracted and reconstructed with the outgoing data, in this mode there must be two independent sources of timing. One
source lies on the G.703 line side of the interface while the other lies on the differential Manchester side of the interface.
DMR = Differential Manchester Receiver

DMR G7X DMX = Differential Manchester Transmitter
G7X = G.703 Transmitter
G7R = G.703 Receiver
DMX G7R
842775A1.CDR
Figure 3–34: G.703 DUAL LOOPBACK MODE

3.3.5 RS422 INTERFACE
a) DESCRIPTION
There are two RS422 inter-relay communications modules available: single-channel RS422 (module 7T) and dual-channel
RS422 (module 7W). The modules can be configured to run at 64 kbps or 128 kbps. AWG 20-24 twisted shielded pair cable
is recommended for external connections. These modules are protected by optically-isolated surge suppression devices.
The shield pins (6a and 7b) are internally connected to the ground pin (8a). Proper shield termination is as follows:
• Site 1: Terminate shield to pins 6a or 7b or both.
• Site 2: Terminate shield to COM pin 2b.
Match the clock terminating impedance with the impedance of the line.
Single-channel RS422 module Dual-channel RS422 module
~ 3b ~ 3b 3
7W
Tx – Tx –
7T
~ 3a Rx – ~ 3a Rx –
RS422
~ 2a Tx + RS422 ~ 2a Tx +
channel 1
Inter-relay comms.
~ 4b Rx + ~ 4b Rx +
~ 6a Shield ~ 6a Shield
Inter-relay communications
~ 7a ~ 5b Tx –
Clock
~ 8b ~ 5a Rx –
RS422
~ 2b COM ~ 4a Tx +
channel 2
~ 8a Surge ~ 6b Rx +
~ 7b Shield
~ 7a
Clock
~ 8b
~ 2b COM
~ indicates the slot position ~ 8a Surge

842776A3.CDR
Figure 3–35: RS422 INTERFACE CONNECTIONS

The following figure shows the typical pin interconnection between two single-channel RS422 interfaces installed in slot W.
All pin interconnections are to be maintained for a connection to a multiplexer.
Figure 3–36: TYPICAL PIN INTERCONNECTION BETWEEN TWO RS422 INTERFACES
b) TWO-CHANNEL APPLICATION VIA MULTIPLEXERS

The RS422 interface can be used for single channel or two channel applications over SONET/SDH or multiplexed systems.
When used in single-channel applications, the RS422 interface links to higher order systems in a typical fashion observing
transmit (Tx), receive (Rx), and send timing (ST) connections. However, when used in two-channel applications, certain cri-
teria must be followed since there is one clock input for the two RS422 channels. The system functions correctly when the
following connections are observed and your data module has a terminal timing feature. Terminal timing is a common fea-
ture to most synchronous data units that allows the module to accept timing from an external source. Using the terminal
timing feature, two channel applications can be achieved if these connections are followed: The send timing outputs from
the multiplexer (data module 1), connects to the clock inputs of the UR–RS422 interface in the usual fashion. In addition,
the send timing outputs of data module 1 is also paralleled to the terminal timing inputs of data module 2. By using this con-
figuration, the timing for both data modules and both UR–RS422 channels are derived from a single clock source. As a
result, data sampling for both of the UR–RS422 channels is synchronized via the send timing leads on data module 1 as
shown below. If the terminal timing feature is not available or this type of connection is not desired, the G.703 interface is a
viable option that does not impose timing restrictions.

Data module 1
Signal name
Tx1(+) W 2a SD(A) - Send data
7W
Tx1(-) W 3b SD(B) - Send data
RS422
CHANNEL 1
Rx1(+) W 4b RD(A) - Received data
Rx1(-) W 3a RD(B) - Received data
Shld. W 6a RS(A) - Request to send (RTS)
INTER-RELAY COMMUNICATIONS
+ W 7a RS(B) - Request to send (RTS)
CLOCK
– W 8b RT(A) - Receive timing
Tx2(+) W 4a RT(B) - Receive timing
Tx2(-) W 5b CS(A) - Clear To send
RS422
CHANNEL 2
Rx2(+) W 6b CS(B) - Clear To send
Rx2(-) W 5a Local loopback
Shld. W 7b Remote loopback
com W 2b Signal ground
SURGE W 8a ST(A) - Send timing
3
ST(B) - Send timing
Data module 2
Signal name
TT(A) - Terminal timing
TT(B) - Terminal timing
SD(A) - Send data
SD(B) - Send data
RD(A) - Received data
RD(B) - Received data
RS(A) - Request to send (RTS)
RS(B) - Request to send (RTS)
CS(A) - Clear To send
CS(B) - Clear To send
Local loopback
Remote loopback
Signal ground
ST(A) - Send timing
ST(B) - Send timing
831022A3.CDR
Figure 3–37: TIMING CONFIGURATION FOR RS422 TWO-CHANNEL, THREE-TERMINAL APPLICATION

Data module 1 provides timing to the D60 RS422 interface via the ST(A) and ST(B) outputs. Data module 1 also provides
timing to data module 2 TT(A) and TT(B) inputs via the ST(A) and AT(B) outputs. The data module pin numbers have been
omitted in the figure above since they vary by manufacturer.
c) TRANSMIT TIMING
The RS422 interface accepts one clock input for transmit timing. It is important that the rising edge of the 64 kHz transmit
timing clock of the multiplexer interface is sampling the data in the center of the transmit data window. Therefore, it is impor-
tant to confirm clock and data transitions to ensure proper system operation. For example, the following figure shows the
positive edge of the Tx clock in the center of the Tx data bit.
Tx Clock
Tx Data
831733A1.CDR
Figure 3–38: CLOCK AND DATA TRANSITIONS

d) RECEIVE TIMING
The RS422 interface utilizes NRZI-MARK modulation code and; therefore, does not rely on an Rx clock to recapture data.
NRZI-MARK is an edge-type, invertible, self-clocking code.
To recover the Rx clock from the data-stream, an integrated DPLL (digital phase lock loop) circuit is utilized. The DPLL is
driven by an internal clock, which is 16-times over-sampled, and uses this clock along with the data-stream to generate a
data clock that can be used as the SCC (serial communication controller) receive clock.
3.3.6 RS422 AND FIBER INTERFACE
The following figure shows the combined RS422 plus fiberoptic interface configuration at 64K baud. The 7L, 7M, 7N, 7P,
and 74 modules are used in two-terminal with a redundant channel or three-terminal configurations where channel 1 is
employed via the RS422 interface (possibly with a multiplexer) and channel 2 via direct fiber.
AWG 20-24 twisted shielded pair is recommended for external RS422 connections and ground the shield only at one end. 3
For the direct fiber channel, address power budget issues properly.
When using a LASER Interface, attenuators can be necessary to ensure that you do not exceed
Figure 3–39: RS422 AND FIBER INTERFACE CONNECTION

Connections shown above are for multiplexers configured as DCE (data communications equipment) units.
3.3.7 G.703 AND FIBER INTERFACE
The figure below shows the combined G.703 plus fiberoptic interface configuration at 64 kbps. The 7E, 7F, 7G, 7Q, and 75
modules are used in configurations where channel 1 is employed via the G.703 interface (possibly with a multiplexer) and
channel 2 via direct fiber. AWG 24 twisted shielded pair is recommended for external G.703 connections connecting the
shield to pin 1a at one end only. For the direct fiber channel, address power budget issues properly. See previous sections
for additional details on the G.703 and fiber interfaces.
When using a laser Interface, attenuators can be necessary to ensure that you do not exceed the

Figure 3–40: G.703 AND FIBER INTERFACE CONNECTION

3 3.3.8 IEEE C37.94 INTERFACE
The UR-series IEEE C37.94 communication modules (modules types 2G, 2H, 76, and 77) are designed to interface with
IEEE C37.94 compliant digital multiplexers or an IEEE C37.94 compliant interface converter for use with direct input and
output applications. The IEEE C37.94 standard defines a point-to-point optical link for synchronous data between a multi-
plexer and a teleprotection device. This data is typically 64 kbps, but the standard provides for speeds up to 64n kbps,
where n = 1, 2,…, 12. The UR-series C37.94 communication modules are either 64 kbps (with n fixed at 1) for 128 kbps
(with n fixed at 2). The frame is a valid International Telecommunications Union (ITU-T) recommended G.704 pattern from
the standpoint of framing and data rate. The frame is 256 bits and is repeated at a frame rate of 8000 Hz, with a resultant bit
rate of 2048 kbps.
The specifications for the module are as follows:.
• IEEE standard: C37.94 for 1  128 kbps optical fiber interface (for 2G and 2H modules) or C37.94 for 2  64 kbps opti-
cal fiber interface (for 76 and 77 modules)
• Fiber optic cable type: 50 mm or 62.5 mm core diameter optical fiber
• Fiber optic mode: multi-mode
• Fiber optic cable length: up to 2 km
• Fiber optic connector: type ST
• Wavelength: 830 ±40 nm
• Connection: as per all fiber optic connections, a Tx to Rx connection is required
The UR-series C37.94 communication module can be connected directly to any compliant digital multiplexer that supports
the IEEE C37.94 standard as shown below.

The UR-series C37.94 communication module can be connected to the electrical interface (G.703, RS422, or X.21) of a
non-compliant digital multiplexer via an optical-to-electrical interface converter that supports the IEEE C37.94 standard, as
shown below.
The UR-series C37.94 communication module has six switches that are used to set the clock configuration. The functions
of these control switches are shown below.
3
For the internal timing mode, the system clock is generated internally. Therefore, the timing switch selection should be
internal timing for relay 1 and loop timed for relay 2. There must be only one timing source configured.
For the looped timing mode, the system clock is derived from the received line signal. Therefore, the timing selection
should be in loop timing mode for connections to higher order systems.
The IEEE C37.94 communications module cover removal procedure is as follows:
1. With power to the relay off, remove the IEEE C37.94 module (type 2G, 2H, 76 or 77 module) as follows. Record the
original location of the module to help ensure that the same or replacement module is inserted into the correct slot.
module for removal.
5. Set the timing selection switches (channel 1, channel 2) to the desired timing modes (see description above).
6. Replace the top cover and the cover screw.
7. Re-insert the IEEE C37.94 module. Take care to ensure that the correct module type is inserted into the correct slot
position. The ejector/inserter clips located at the top and at the bottom of each module must be in the disengaged posi-
tion as the module is smoothly inserted into the slot. Once the clips have cleared the raised edge of the chassis,
engage the clips simultaneously. When the clips have locked into position, the module is fully inserted.

Figure 3–41: IEEE C37.94 TIMING SELECTION SWITCH SETTING

Modules shipped since January 2012 have status LEDs that indicate the status of the DIP switches, as shown in the follow-
ing figure.
Figure 3–42: STATUS LEDS

The clock configuration LED status is as follows:
• Flashing green — loop timing mode while receiving a valid data packet
• Flashing yellow — internal mode while receiving a valid data packet
• Solid red — (switch to) internal timing mode while not receiving a valid data packet
The link/activity LED status is as follows:
• Flashing green — FPGA is receiving a valid data packet
• Solid yellow — FPGA is receiving a "yellow bit" and remains yellow for each "yellow bit"
• Solid red — FPGA is not receiving a valid packet or the packet received is invalid

3.3.9 C37.94SM INTERFACE
The UR-series C37.94SM communication modules (2A and 2B) are designed to interface with modified IEEE C37.94 com-
pliant digital multiplexers or IEEE C37.94 compliant interface converters that have been converted from 820 nm multi-mode
fiber optics to 1300 nm ELED single-mode fiber optics. The IEEE C37.94 standard defines a point-to-point optical link for
synchronous data between a multiplexer and a teleprotection device. This data is typically 64 kbps, but the standard pro-
vides for speeds up to 64n kbps, where n = 1, 2,…, 12. The UR-series C37.94SM communication module is 64 kbps only
with n fixed at 1. The frame is a valid International Telecommunications Union (ITU-T) recommended G.704 pattern from
the standpoint of framing and data rate. The frame is 256 bits and is repeated at a frame rate of 8000 Hz, with a resultant bit
rate of 2048 kbps.
The specifications for the module are as follows:
• Emulated IEEE standard: emulates C37.94 for 1  64 kbps optical fiber interface (modules set to n = 1 or 64 kbps)
3 • Fiber optic cable type: 9/125 m core diameter optical fiber
• Fiber optic mode: single-mode, ELED compatible with HP HFBR-1315T transmitter and HP HFBR-2316T receiver
• Fiber optic cable length: up to 11.4 km
• Fiber optic connector: type ST
• Wavelength: 1300 ±40 nm
• Connection: as per all fiber optic connections, a Tx to Rx connection is required
The UR-series C37.94SM communication module can be connected directly to any compliant digital multiplexer that sup-
ports C37.94SM as shown below.
It can also can be connected directly to any other UR-series relay with a C37.94SM module as shown below.
The UR-series C37.94SM communication module has six switches that are used to set the clock configuration. The func-
tions of these control switches are shown below.
For the internal timing mode, the system clock is generated internally. Therefore, the timing switch selection should be
internal timing for relay 1 and loop timed for relay 2. There must be only one timing source configured.

For the looped timing mode, the system clock is derived from the received line signal. Therefore, the timing selection
should be in loop timing mode for connections to higher order systems.
The C37.94SM communications module cover removal procedure is as follows:
1. With power to the relay off, remove the C37.94SM module (modules 2A or 2B) as follows. Record the original location
of the module to help ensure that the same or replacement module is inserted into the correct slot.
module for removal.
5. Set the timing selection switches (channel 1, channel 2) to the desired timing modes (see description above).
6.
7.
Replace the top cover and the cover screw.
Re-insert the C37.94SM module. Take care to ensure that the correct module type is inserted into the correct slot
3
position. The ejector/inserter clips located at the top and at the bottom of each module must be in the disengaged posi-
tion as the module is smoothly inserted into the slot. Once the clips have cleared the raised edge of the chassis,
engage the clips simultaneously. When the clips have locked into position, the module is fully inserted.
Figure 3–43: C37.94SM TIMING SELECTION SWITCH SETTING

Modules shipped since January 2012 have status LEDs that indicate the status of the DIP switches, as shown in the follow-
ing figure.
Figure 3–44: STATUS LEDS

The clock configuration LED status is as follows:
• Flashing green — loop timing mode while receiving a valid data packet
• Flashing yellow — internal mode while receiving a valid data packet
• Solid red — (switch to) internal timing mode while not receiving a valid data packet
The link/activity LED status is as follows:
• Flashing green — FPGA is receiving a valid data packet
• Solid yellow — FPGA is receiving a "yellow bit" and remains yellow for each "yellow bit"
• Solid red — FPGA is not receiving a valid packet or the packet received is invalid

4 HUMAN INTERFACES 4.1 ENERVISTA UR SETUP SOFTWARE INTERFACE
4 HUMAN INTERFACES 4.1ENERVISTA UR SETUP SOFTWARE INTERFACE 4.1.1 INTRODUCTION
The EnerVista UR Setup software provides a graphical user interface (GUI) as one of two human interfaces to a UR device.
The alternate human interface is implemented via the device’s faceplate keypad and display (see the Faceplate interface
section in this chapter).
The EnerVista UR Setup software provides a single facility to configure, monitor, maintain, and troubleshoot the operation
of relay functions, connected over local or wide area communication networks. It can be used while disconnected (offline)
or connected (online) to a UR device. In offline mode, settings files can be created for eventual downloading to the device.
In online mode, you can communicate with the device in real-time.
The EnerVista UR Setup software is provided with every D60 relay and runs on Microsoft Windows XP, 7, and Server 2008.
This chapter provides a summary of the basic EnerVista UR Setup software interface features. The EnerVista UR Setup
Help File provides details for getting started and using the EnerVista UR Setup software interface.
4.1.2 CREATING A SITE LIST
To start using the EnerVista UR Setup software, site and device definition are required. See the EnerVista UR Setup Help
File or refer to the Connecting EnerVista UR Setup with the D60 section in Chapter 1 for details.
4.1.3 ENERVISTA UR SETUP OVERVIEW 4

a) ENGAGING A DEVICE
The EnerVista UR Setup software can be used in online mode (relay connected) to directly communicate with the D60
relay. Communicating relays are organized and grouped by communication interfaces and into sites. Sites can contain any
number of relays selected from the UR-series of relays.
b) USING SETTINGS FILES

The EnerVista UR Setup software interface supports three ways of handling changes to relay settings:
• In offline mode (relay disconnected) to create or edit relay settings files for later download to communicating relays
• While connected to a communicating relay to directly modify any relay settings via relay data view windows, and then
save the settings to the relay
• You can create/edit settings files and then write them to the relay while the interface is connected to the relay
Settings files are organized on the basis of file names assigned by the user. A settings file contains data pertaining to the
following types of relay settings:
• Device definition
• Product setup
• FlexLogic
• Control elements
• Inputs/outputs
• Testing
Factory default values are supplied and can be restored after any changes.
The following communications settings are not transferred to the D60 with settings files.
Modbus Slave Address
Modbus IP Port Number
RS485 COM2 Baud Rate
RS485 COM2 Parity
COM2 Minimum Response Time
COM2 Selection
RRTD Slave Address
RRTD Baud Rate

4.1 ENERVISTA UR SETUP SOFTWARE INTERFACE 4 HUMAN INTERFACES
IP Address
IP Subnet Mask
IEC61850 Config GOOSE ConfRev
IP Routing
When a settings file is loaded to a D60 that is in-service, the following sequence occurs:
1. The D60 takes itself out of service.
2. The D60 issues a UNIT NOT PROGRAMMED major self-test error.
3. The D60 closes the critical fail contact.
c) CREATING AND EDITING FLEXLOGIC

You create or edit a FlexLogic equation in order to customize the relay. You can subsequently view the automatically gener-
ated logic diagram.
d) VIEWING ACTUAL VALUES

You can view real-time relay data such as input/output status and measured parameters.
4 e) VIEWING TRIGGERED EVENTS

While the interface is in either online or offline mode, you can view and analyze data generated by triggered specified
parameters, via one of the following:
• Event recorder
The event recorder captures contextual data associated with the last 1024 events, listed in chronological order from
most recent to oldest.
• Oscillography
The oscillography waveform traces and digital states are used to provide a visual display of power system and relay
operation data captured during specific triggered events.
f) FILE SUPPORT
• Execution: Any EnerVista UR Setup file that is opened launches the application or provides focus to the already
opened application. If the file was a settings file (has a URS extension) that had been removed from the Settings List
tree menu, it is added back to the Settings List tree menu.
• Drag and Drop: The Site List and Settings List control bar windows are each mutually a drag source and a drop target
for device-order-code-compatible files or individual menu items. Also, the Settings List control bar window and any
Windows Explorer directory folder are each mutually a file drag source and drop target.
New files that are dropped into the Settings List window are added to the tree, which is automatically sorted alphabeti-
cally with respect to settings file names. Files or individual menu items that are dropped in the selected device menu in
the Site List window are automatically sent to the online communicating device.
g) FIRMWARE UPGRADES
The firmware of a D60 device can be upgraded, locally or remotely, via the EnerVista UR Setup software. The correspond-
ing instructions are provided by the EnerVista UR Setup Help file under the topic “Upgrading Firmware”.
Modbus addresses assigned to firmware modules, features, settings, and corresponding data items (that is, default
values, minimum/maximum values, data type, and item size) can change slightly from version to version of firm-
NOTE
ware. The addresses are rearranged when new features are added or existing features are enhanced or modified.
The EEPROM DATA ERROR message displayed after upgrading/downgrading the firmware is a resettable, self-test
message intended to inform users that the Modbus addresses have changed with the upgraded firmware. This
message does not signal any problems when appearing after firmware upgrades.

4 HUMAN INTERFACES 4.1 ENERVISTA UR SETUP SOFTWARE INTERFACE
4.1.4 ENERVISTA UR SETUP MAIN WINDOW
The EnerVista UR Setup software main window supports the following primary display components:
1. Title bar that shows the pathname of the active data view
2. Main window menu bar
3. Main window tool bar
4. Site list control bar window
5. Settings list control bar window
6. Device data view windows, with common tool bar
7. Settings file data view windows, with common tool bar
8. Workspace area with data view tabs
9. Status bar
10. Quick action hot links
2 1 6 7 4
10
4
9 8 842786A2.CDR
Figure 4–1: ENERVISTA UR SETUP SOFTWARE MAIN WINDOW

4.2 EXTENDED ENERVISTA UR SETUP FEATURES 4 HUMAN INTERFACES
4.2EXTENDED ENERVISTA UR SETUP FEATURES 4.2.1 SETTINGS TEMPLATES
Setting file templates simplify the configuration and commissioning of multiple relays that protect similar assets. An exam-
ple of this is a substation that has ten similar feeders protected by ten UR-series F60 relays.
In these situations, typically 90% or greater of the settings are identical between all devices. The templates feature allows
engineers to configure and test these common settings, then lock them so that they are not available to users. For exam-
ple, these locked down settings can be hidden from view for field engineers, allowing them to quickly identify and concen-
trate on the specific settings.
The remaining settings (typically 10% or less) can be specified as editable and be made available to field engineers install-
ing the devices. These are settings such as protection element pickup values and CT and VT ratios.
The settings template mode allows the user to define which settings are visible in EnerVista UR Setup. Settings templates
can be applied to both settings files (settings file templates) and online devices (online settings templates). The functionality
is identical for both purposes.
Settings files conversion from previous firmware versions is supported.
a) ENABLING THE SETTINGS TEMPLATE

The settings file template feature is disabled by default. The following procedure describes how to enable the settings tem-
4 plate for UR-series settings files.
1. Select a settings file from the offline window of the EnerVista UR Setup main screen.
2. Right-click the selected device or settings file and select the Template Mode > Create Template option.
The settings file template is now enabled and the file tree displayed in light blue. The settings file is now in template editing
mode.
Alternatively, the settings template can also be applied to online settings. The following procedure describes this process.
1. Select an installed device from the online window of the EnerVista UR Setup main screen.
2. Right-click the selected device and select the Template Mode > Create Template option.
The software prompts for a template password. This password is required to use the template feature and must be at
least four characters in length.
3. Enter and re-enter the new password, then click OK to continue.
The online settings template is now enabled. The device is now in template editing mode.
b) EDITING THE SETTINGS TEMPLATE

The settings template editing feature allows the user to specify which settings are available for viewing and modification in
EnerVista UR Setup. By default, all settings except the FlexLogic equation editor settings are locked.
1. Select an installed device or a settings file from the tree menu on the left of the EnerVista UR Setup main screen.
2. Select the Template Mode > Edit Template option to place the device in template editing mode.
3. Enter the template password then click OK.
4. Open the relevant settings windows that contain settings to be specified as viewable.

4 HUMAN INTERFACES 4.2 EXTENDED ENERVISTA UR SETUP FEATURES
By default, all settings are specified as locked and displayed against a grey background. The icon on the upper right of
the settings window also indicates that EnerVista UR Setup is in EDIT mode. The following example shows the phase
time overcurrent settings window in edit mode.
Figure 4–2: SETTINGS TEMPLATE VIEW, ALL SETTINGS SPECIFIED AS LOCKED

5. Specify the settings to make viewable by clicking them. 4
The setting available to view is displayed against a yellow background as shown below.
Figure 4–3: SETTINGS TEMPLATE VIEW, TWO SETTINGS SPECIFIED AS EDITABLE

6. Click on Save to save changes to the settings template.
7. Proceed through the settings tree to specify all viewable settings.
c) ADDING PASSWORD PROTECTION TO A TEMPLATE

It is highly recommended that templates be saved with password protection to maximize security.
The following procedure describes how to add password protection to a settings file template.
1. Select a settings file from the offline window on the left of the EnerVista UR Setup main screen.
2. Selecting the Template Mode > Password Protect Template option.

The software prompts for a template password. This password must be at least four characters in length.
3. Enter and re-enter the new password, then click OK to continue.

The settings file template is now secured with password protection.
When templates are created for online settings, the password is added during the initial template creation step. It
does not need to be added after the template is created.
NOTE
d) VIEWING THE SETTINGS TEMPLATE

Once all necessary settings are specified for viewing, users are able to view the settings template on the online device or
4 settings file. There are two ways to specify the settings view with the settings template feature:
• Display only those settings available for editing
• Display all settings, with settings not available for editing greyed-out
Use the following procedure to only display settings available for editing:
2. Apply the template by selecting the Template Mode > View In Template Mode option.
3. Enter the template password then click OK to apply the template.
Once the template has been applied, users are limited to view and edit the settings specified by the template. The effect of
applying the template to the phase time overcurrent settings is shown below.
Phase time overcurrent window with template applied via

the Template Mode > View In Template Mode command.
The template specifies that only the Pickup and Curve
Phase time overcurrent settings window without template applied.
settings be available.
842858A1.CDR
Figure 4–4: APPLYING TEMPLATES VIA THE VIEW IN TEMPLATE MODE COMMAND

Viewing the settings in template mode also modifies the settings tree, showing only the settings categories that contain
editable settings. The effect of applying the template to a typical settings tree view is shown below.
Typical settings tree view without template applied. Typical settings tree view with template applied via
the Template Mode > View In Template Mode
command.
842860A1.CDR
Figure 4–5: APPLYING TEMPLATES VIA THE VIEW IN TEMPLATE MODE SETTINGS COMMAND
Use the following procedure to display settings available for editing and settings locked by the template. 4
2. Apply the template by selecting the Template Mode > View All Settings option.
3. Enter the template password then click OK to apply the template.
Once the template has been applied, users are limited to edit the settings specified by the template, but all settings are
shown. The effect of applying the template to the phase time overcurrent settings is shown below.
Phase time overcurrent settings window without template applied. Phase time overcurrent window with template applied via
the Template Mode > View All Settings command.
The template specifies that only the Pickup and Curve
settings be available.
842859A1.CDR
Figure 4–6: APPLYING TEMPLATES VIA THE VIEW ALL SETTINGS COMMAND
e) REMOVING THE SETTINGS TEMPLATE

It can be necessary at some point to remove a settings template. Once a template is removed, it cannot be reapplied and it
is necessary to define a new settings template.
1. Select an installed device or settings file from the tree menu on the left of the EnerVista UR Setup main screen.
2. Select the Template Mode > Remove Settings Template option.
3. Enter the template password and click OK to continue.

4. Verify one more time that you want to remove the template by clicking Yes.
The EnerVista software removes all template information and all settings are available.
4.2.2 SECURING AND LOCKING FLEXLOGIC EQUATIONS
The UR allows users to secure parts or all of a FlexLogic equation, preventing unauthorized viewing or modification of criti-
cal FlexLogic applications. This is accomplished using the settings template feature to lock individual entries within Flex-
Logic equations.
Secured FlexLogic equations remain secure when files are sent to and retrieved from any UR-series device.
a) LOCKING FLEXLOGIC EQUATION ENTRIES
4 The following procedure describes how to lock individual entries of a FlexLogic equation.
1. Right-click the settings file or online device and select the Template Mode > Create Template item to enable the set-
tings template feature.
2. Select the FlexLogic > FlexLogic Equation Editor settings menu item.
By default, all FlexLogic entries are specified as viewable and displayed against a yellow background. The icon on the
upper right of the window also indicates that EnerVista UR Setup is in EDIT mode.
3. Specify which entries to lock by clicking on them.
The locked entries are displayed against a grey background as shown in the example below.
Figure 4–7: LOCKING FLEXLOGIC ENTRIES IN EDIT MODE

4. Click on Save to save and apply changes to the settings template.
5. Select the Template Mode > View In Template Mode option to view the template.
6. Apply a password to the template then click OK to secure the FlexLogic equation.

Once the template has been applied, users are limited to view and edit the FlexLogic entries not locked by the template.
The effect of applying the template to the FlexLogic entries in the above procedure is shown below.
Typical FlexLogic™ entries without template applied. Typical FlexLogic™ entries locked with template via
the Template Mode > View In Template Mode command.
842861A1.CDR
Figure 4–8: LOCKING FLEXLOGIC ENTRIES THROUGH SETTING TEMPLATES 4

The FlexLogic entries are also shown as locked in the graphical view (as shown below) and on the front panel display.
Figure 4–9: SECURED FLEXLOGIC IN GRAPHICAL VIEW
b) LOCKING FLEXLOGIC EQUATIONS TO A SERIAL NUMBER

A settings file and associated FlexLogic equations can also be locked to a specific UR serial number. Once the desired
FlexLogic entries in a settings file have been secured, use the following procedure to lock the settings file to a specific serial
number.
1. Select the settings file in the offline window.
2. Right-click on the file and select the Edit Settings File Properties item.

The following window is displayed.
Figure 4–10: TYPICAL SETTINGS FILE PROPERTIES WINDOW
4 3. Enter the serial number of the D60 device to lock to the settings file in the Serial # Lock field.
The settings file and corresponding secure FlexLogic equations are now locked to the D60 device specified by the serial
number.
4.2.3 SETTINGS FILE TRACEABILITY
A traceability feature for settings files allows the user to quickly determine if the settings in a D60 device have been
changed since the time of installation from a settings file. When a settings file is transferred to a D60 device, the date, time,
and serial number of the D60 are sent back to EnerVista UR Setup and added to the settings file on the local PC. This infor-
mation can be compared with the D60 actual values at any later date to determine if security has been compromised.
The traceability information is only included in the settings file if a complete settings file is either transferred to the D60
device or obtained from the D60 device. Any partial settings transfers by way of drag and drop do not add the traceability
information to the settings file.
Figure 4–11: SETTINGS FILE TRACEABILITY MECHANISM

With respect to the above diagram, the traceability feature is used as follows.

1. The transfer date of a setting file written to a D60 is logged in the relay and can be viewed via EnerVista UR Setup or
the front panel display. Likewise, the transfer date of a setting file saved to a local PC is logged in EnerVista UR Setup.
2. Comparing the dates stored in the relay and on the settings file at any time in the future indicates if any changes have
been made to the relay configuration since the settings file was saved.
a) SETTINGS FILE TRACEABILITY INFORMATION

The serial number and file transfer date are saved in the settings files when they are sent to a D60 device.
The D60 serial number and file transfer date are included in the settings file device definition within the EnerVista UR Setup
offline window as shown in the example below.
Traceability data in settings

file device definition
4
842863A1.CDR
Figure 4–12: DEVICE DEFINITION SHOWING TRACEABILITY DATA

This information is also available in printed settings file reports as shown in the example below.
Traceability data
in settings report
842862A1.CDR
Figure 4–13: SETTINGS FILE REPORT SHOWING TRACEABILITY DATA

b) ONLINE DEVICE TRACEABILITY INFORMATION

The D60 serial number and file transfer date are available for an online device through the actual values. Select the Actual
Values > Product Info > Model Information menu item within the EnerVista UR Setup online window as shown in the
example below.
Traceability data in online

device actual values page
842865A1.CDR
Figure 4–14: TRACEABILITY DATA IN ACTUAL VALUES WINDOW

This information is also available from the front panel display through the following actual values:
ACTUAL VALUES  PRODUCT INFO  MODEL INFORMATION  SERIAL NUMBER
ACTUAL VALUES  PRODUCT INFO  MODEL INFORMATION  LAST SETTING CHANGE
c) ADDITIONAL TRACEABILITY RULES
4 The following additional rules apply for the traceability feature

• If the user changes any settings within the settings file in the offline window, then the traceability information is
removed from the settings file.
• If the user creates a new settings file, then no traceability information is included in the settings file.
• If the user converts an existing settings file to another revision, then any existing traceability information is removed
from the settings file.
• If the user duplicates an existing settings file, then any traceability information is transferred to the duplicate settings
file.

4 HUMAN INTERFACES 4.3 FACEPLATE INTERFACE
4.3FACEPLATE INTERFACE 4.3.1 FACEPLATE
a) ENHANCED FACEPLATE
The front panel interface is one of two supported interfaces, the other interface being EnerVista UR Setup software. The
front panel interface consists of LED panels, an RS232 port, keypad, LCD display, control pushbuttons, and optional user-
programmable pushbuttons.
The faceplate is hinged to allow easy access to the removable modules.
Five column LED indicator panel
Display
Keypad
4
Front panel
RS232 port
User-programmable pushbuttons 1 to 16 842810A1.CDR

Figure 4–15: UR-SERIES ENHANCED FACEPLATE
b) STANDARD FACEPLATE
There are two interfaces: the front panel and the EnerVista UR Setup software. The front panel interface consists of LED
panels, an RS232 port, keypad, LCD display, control pushbuttons, and optional user-programmable pushbuttons.
The faceplate is hinged to allow easy access to the removable modules. There is also a removable dust cover that fits over
the faceplate that must be removed in order to access the keypad panel. The following figure shows the horizontal arrange-
ment of the faceplate panels.
LED panel 1 LED panel 2 LED panel 3
Display
Front panel
RS232 port
Small user-programmable User-programmable

(control) pushbuttons 1 to 7 pushbuttons 1 to 12 Keypad
827801A.DL
Figure 4–16: UR-SERIES STANDARD HORIZONTAL FACEPLATE PANELS

4.3 FACEPLATE INTERFACE 4 HUMAN INTERFACES
The following figure shows the vertical arrangement of the faceplate panels for relays ordered with the vertical option.
Figure 4–17: UR-SERIES STANDARD VERTICAL FACEPLATE PANELS
4.3.2 LED INDICATORS
The enhanced front panel display provides five columns of LED indicators. The first column contains 14 status and event
cause LEDs, and the next four columns contain the 48 user-programmable LEDs.
The RESET key is used to reset any latched LED indicator or target message, once the condition has been cleared (these
latched conditions can also be reset via the SETTINGS  INPUT/OUTPUTS  RESETTING menu). The RS232 port is
intended for connection to a portable PC.
The USER keys are used by the breaker control feature.
842811A1.CDR
Figure 4–18: TYPICAL LED INDICATOR PANEL FOR ENHANCED FACEPLATE

The status indicators in the first column are described below.
• IN SERVICE: This LED indicates that control power is applied, all monitored inputs, outputs, and internal systems are
OK, and that the device has been programmed.

• TROUBLE: This LED indicates that the relay has detected an internal problem.
• TEST MODE: This LED indicates that the relay is in test mode.
• TRIP: This LED indicates that the FlexLogic operand serving as a trip switch has operated. This indicator always
latches; as such, a reset command must be initiated to allow the latch to be reset.
• ALARM: This LED indicates that the FlexLogic operand serving as an alarm switch has operated. This indicator is
never latched.
• PICKUP: This LED indicates that an element is picked up. This indicator is never latched.
The event cause indicators in the first column are described below.
Events cause LEDs are turned on or off by protection elements that have their respective target setting selected as either
“Enabled” or “Latched”. If a protection element target setting is “Enabled”, then the corresponding event cause LEDs
remain on as long as operate operand associated with the element remains asserted. If a protection element target setting
is “Latched”, then the corresponding event cause LEDs turn on when the operate operand associated with the element is
asserted and remain on until the RESET button on the front panel is pressed after the operand is reset.
All elements that are able to discriminate faulted phases can independently turn off or on the phase A, B or C LEDs. This
includes phase instantaneous overcurrent, phase undervoltage, etc. This means that the phase A, B, and C operate oper-
ands for individual protection elements are ORed to turn on or off the phase A, B or C LEDs.
• VOLTAGE: This LED indicates voltage was involved. 4
• CURRENT: This LED indicates current was involved.
• FREQUENCY: This LED indicates frequency was involved.
• OTHER: This LED indicates a composite function was involved.
• PHASE A: This LED indicates phase A was involved.
• PHASE B: This LED indicates phase B was involved.
• PHASE C: This LED indicates phase C was involved.
• NEUTRAL/GROUND: This LED indicates that neutral or ground was involved.
The user-programmable LEDs consist of 48 amber LED indicators in four columns. The operation of these LEDs is user-
defined. Support for applying a customized label beside every LED is provided. Default labels are shipped in the label pack-
age of every D60, together with custom templates. The default labels can be replaced by user-printed labels.
User customization of LED operation is of maximum benefit in installations where languages other than English are used to
communicate with operators. Refer to the User-programmable LEDs section in chapter 5 for the settings used to program
the operation of the LEDs on these panels.
The standard faceplate consists of three panels with LED indicators, keys, and a communications port. The RESET key is
used to reset any latched LED indicator or target message, once the condition has been cleared (these latched conditions
can also be reset via the SETTINGS  INPUT/OUTPUTS  RESETTING menu). The RS232 port is for connection to a com-
puter.
The USER keys are used by the breaker control feature.
STATUS EVENT CAUSE

IN SERVICE VOLTAGE
TROUBLE CURRENT RESET
TEST MODE FREQUENCY
TRIP OTHER USER 1
ALARM PHASE A
PICKUP PHASE B USER 2
PHASE C
NEUTRAL/GROUND USER 3
842781A1.CDR
Figure 4–19: LED PANEL 1

STATUS INDICATORS:
• IN SERVICE: Indicates that control power is applied; all monitored inputs/outputs and internal systems are OK; the
relay has been programmed.
• TROUBLE: Indicates that the relay has detected an internal problem.
• TEST MODE: Indicates that the relay is in test mode.
• TRIP: Indicates that the selected FlexLogic operand serving as a Trip switch has operated. This indicator always
latches; the reset command must be initiated to allow the latch to be reset.
• ALARM: Indicates that the selected FlexLogic operand serving as an Alarm switch has operated. This indicator is
never latched.
• PICKUP: Indicates that an element is picked up. This indicator is never latched.
EVENT CAUSE INDICATORS:
Events cause LEDs are turned on or off by protection elements that have their respective target setting selected as either
“Enabled” or “Latched”. If a protection element target setting is “Enabled”, then the corresponding event cause LEDs
remain on as long as operate operand associated with the element remains asserted. If a protection element target setting
is “Latched”, then the corresponding event cause LEDs turn on when the operate operand associated with the element is
asserted and remain on until the RESET button on the front panel is pressed after the operand is reset.
4 All elements that are able to discriminate faulted phases can independently turn off or on the phase A, B or C LEDs. This
includes phase instantaneous overcurrent, phase undervoltage, etc. This means that the phase A, B, and C operate oper-
ands for individual protection elements are ORed to turn on or off the phase A, B or C LEDs.
• VOLTAGE: Indicates voltage was involved.
• CURRENT: Indicates current was involved.
• FREQUENCY: Indicates frequency was involved.
• OTHER: Indicates a composite function was involved.
• PHASE A: Indicates phase A was involved.
• PHASE B: Indicates phase B was involved.
• PHASE C: Indicates phase C was involved.
• NEUTRAL/GROUND: Indicates that neutral or ground was involved.
USER-PROGRAMMABLE INDICATORS:
The second and third provide 48 amber LED indicators whose operation is controlled by the user. Support for applying a
customized label beside every LED is provided.
User customization of LED operation is of maximum benefit in installations where languages other than English are used to
communicate with operators. Refer to the User-programmable LEDs section in chapter 5 for the settings used to program
the operation of the LEDs on these panels.
USER-PROGRAMMABLE LEDS USER-PROGRAMMABLE LEDS
842782A1.CDR
Figure 4–20: LED PANELS 2 AND 3 (INDEX TEMPLATE)

DEFAULT LABELS FOR LED PANEL 2:
The default labels are intended to represent:

• GROUP 1...6: The illuminated GROUP is the active settings group.

• BREAKER 1(2) OPEN: The breaker is open.
• BREAKER 1(2) CLOSED: The breaker is closed.
• BREAKER 1(2) TROUBLE: A problem related to the breaker has been detected.
• SYNCHROCHECK NO1(2) IN-SYNCH: Voltages have satisfied the synchrocheck element.
• RECLOSE ENABLED: The recloser is operational.
• RECLOSE DISABLED: The recloser is not operational.
• RECLOSE IN PROGRESS: A reclose operation is in progress.
• RECLOSE LOCKED OUT: The recloser is not operational and requires a reset.
Firmware revisions 2.9x and earlier support eight user setting groups; revisions 3.0x and higher support six setting
groups. For convenience of users using earlier firmware revisions, the relay panel shows eight setting groups.
NOTE
Please note that the LEDs, despite their default labels, are fully user-programmable.
The relay is shipped with the default label for the LED panel 2. The LEDs, however, are not pre-programmed. To match the
pre-printed label, the LED settings must be entered as shown in the User-programmable LEDs section of chapter 5. The
LEDs are fully user-programmable. The default labels can be replaced by user-printed labels for both panels as explained
in the following section. 4
842784A1.CDR
Figure 4–21: LED PANEL 2 (DEFAULT LABELS)
4.3.3 CUSTOM LABELING OF LEDS
The following procedure requires these pre-requisites:
• EnerVista UR Setup software is installed and operational
• The D60 settings have been saved to a settings file
• The D60 front panel label cutout sheet (GE Multilin part number 1006-0047) has been downloaded from
http://www.gedigitalenergy.com/products/support/ur/URLEDenhanced.doc and printed
• Small-bladed knife
To create custom LED labels for the enhanced front panel display:
1. Start the EnerVista UR Setup software.

2. Select the Front Panel Report item at the bottom of the menu tree for the settings file. The front panel report window
displays.
4
Figure 4–22: FRONT PANEL REPORT WINDOW
3. Enter the text to appear next to each LED and above each user-programmable pushbuttons in the fields provided.
4. Feed the D60 front panel label cutout sheet into a printer and press the Print button in the front panel report window.
5. When printing is complete, fold the sheet along the perforated lines and punch out the labels.
6. Remove the D60 label insert tool from the package and bend the tabs as described in the following procedures. These
tabs are used for removal of the default and custom LED labels.
It is important that the tool be used EXACTLY as shown below, with the printed side containing the GE part number
facing the user.
NOTE
The label package shipped with every D60 contains the three default labels shown below, the custom label template sheet,
and the label removal tool.
If the default labels are suitable for your application, insert them in the appropriate slots and program the LEDs to match
them. If you require custom labels, follow the procedures below to remove the original labels and insert the new ones.
The following procedure describes how to setup and use the label removal tool.
1. Bend the tabs at the left end of the tool upwards as shown below.

2. Bend the tab at the center of the tool tail as shown below.
The following procedure describes how to remove the LED labels from the D60 enhanced front panel and insert the custom
labels.
1. Use the knife to lift the LED label and slide the label tool underneath. Make sure the bent tabs are pointing away from
the relay.
4
2. Slide the label tool under the LED label until the tabs snap out as shown below. This attaches the label tool to the LED
label.

3. Remove the tool and attached LED label as shown below.
4. Slide the new LED label inside the pocket until the text is properly aligned with the LEDs, as shown below.
The following procedure describes how to remove the user-programmable pushbutton labels from the D60 enhanced front
panel and insert the custom labels.
1. Use the knife to lift the pushbutton label and slide the tail of the label tool underneath, as shown below. Make sure the
bent tab is pointing away from the relay.

2. Slide the label tool under the user-programmable pushbutton label until the tabs snap out as shown below. This
attaches the label tool to the user-programmable pushbutton label.
3. Remove the tool and attached user-programmable pushbutton label as shown below.
4

4. Slide the new user-programmable pushbutton label inside the pocket until the text is properly aligned with the buttons,
as shown below.
Custom labeling of an LED-only panel is facilitated through a Microsoft Word file available from the following URL:
http://www.gedigitalenergy.com/products/support/ur/GET-8494A.doc
This file provides templates and instructions for creating appropriate labeling for the LED panel. The following procedures
are contained in the downloadable file. The panel templates provide relative LED locations and located example text (x)
edit boxes. The following procedure demonstrates how to install/uninstall the custom panel labeling.
1. Remove the clear Lexan Front Cover (GE Multilin part number: 1501-0014).
F60 FEEDER MANAGEMENT RELAY

R
Push in
and gently lift
up the cover.
842771A1.CDR
2. Pop out the LED module and/or the blank module with a screwdriver as shown below. Be careful not to damage the
plastic covers.
( LED MODULE ) ( BLANK MODULE )
F60
R
FEEDER MANAGEMENT RELAY
842722A1.CDR
3. Place the left side of the customized module back to the front panel frame, then snap back the right side.
4. Put the clear Lexan front cover back into place.

The following items are required to customize the D60 display module:
• Black and white or color printer (color preferred)
• Microsoft Word 97 or later software for editing the template
• 1 each of: 8.5" x 11" white paper, exacto knife, ruler, custom display module (GE Multilin Part Number: 1516-0069),
and a custom module cover (GE Multilin Part Number: 1502-0015)
The following procedure describes how to customize the D60 display module:
1. Open the LED panel customization template with Microsoft Word. Add text in places of the LED x text placeholders on
the template(s). Delete unused place holders as required.
2. When complete, save the Word file to your computer for future use.
3. Print the template(s) to a local printer.
4. From the printout, cut-out the Background Template from the three windows, using the cropmarks as a guide.
5. Put the Background Template on top of the custom display module (GE Multilin Part Number: 1513-0069) and snap the
clear custom module cover (GE Multilin Part Number: 1502-0015) over it and the templates.
4.3.4 DISPLAY
All messages are displayed on a backlit liquid crystal display (LCD) to make them visible under poor lighting conditions.
4
While the keypad and display are not actively being used, the display defaults to user-defined messages. Any high-priority
event-driven message automatically overrides the default message and appears on the display.
4.3.5 KEYPAD
Display messages are organized into pages under the following headings: actual values, settings, commands, and targets.
The MENU key navigates through these pages. Each heading page is divided further into logical subgroups.
The MESSAGE keys navigate through the subgroups. The VALUE keys increment or decrement numerical setting values
when in programming mode. These keys also scroll through alphanumeric values in the text edit mode. Alternatively, val-
ues can be entered with the numeric keypad.
The decimal key initiates and advances to the next character in text edit mode or enters a decimal point.
The HELP key can be pressed at any time for context-sensitive help messages.
The ENTER key stores altered setting values.
4.3.6 BREAKER CONTROL
a) INTRODUCTION
The D60 can interface with associated circuit breakers. In many cases the application monitors the state of the breaker, that
can be presented on faceplate LEDs, along with a breaker trouble indication. Breaker operations can be manually initiated
from faceplate keypad or automatically initiated from a FlexLogic operand. A setting is provided to assign names to each
breaker; this user-assigned name is used for the display of related flash messages. These features are provided for two
breakers; the user can use only those portions of the design relevant to a single breaker, which must be breaker 1.
For the following discussion it is assumed the SETTINGS  SYSTEM SETUP  BREAKERS  BREAKER 1(2)  BREAKER
FUNCTION setting is "Enabled" for each breaker.
b) CONTROL MODE SELECTION AND MONITORING

Installations can require that a breaker is operated in the three-pole only mode (3-pole), or in the one and three-pole (1-
pole) mode, selected by setting. If the mode is selected as three-pole, a single input tracks the breaker open or closed posi-
tion. If the mode is selected as one-pole, all three breaker pole states must be input to the relay. These inputs must be in
agreement to indicate the position of the breaker.
For the following discussion it is assumed the SETTINGS  SYSTEM SETUP  BREAKERS  BREAKER 1(2)  BREAKER
1(2) PUSH BUTTON CONTROL setting is “Enabled” for each breaker.

The D60 has features required for single-pole operation. Inputs that trip individual breaker poles and cause a breaker
reclose are passed directly to this element.
c) FACEPLATE (USER KEY) CONTROL

After the 30 minute interval during which command functions are permitted after a correct command password, the user
cannot open or close a breaker via the keypad. The following discussions begin from the not-permitted state.
d) CONTROL OF TWO BREAKERS

For the following example setup, the (Name) field represents the user-programmed variable name.
For this application (setup shown below), the relay is connected and programmed for both breaker 1 and breaker 2. The
USER 1 key performs the selection of which breaker is to be operated by the USER 2 and USER 3 keys. The USER 2 key
is used to manually close the breaker and the USER 3 key is used to manually open the breaker.
ENTER COMMAND This message appears when the USER 1, USER 2, or USER 3 key is pressed and a
PASSWORD COMMAND PASSWORD is required; i.e. if COMMAND PASSWORD is enabled and no com-
mands have been issued within the last 30 minutes.
Press USER 1 This message appears if the correct password is entered or if none is required. This mes-
4 To Select Breaker sage displays for 30 seconds or until the USER 1 key is pressed again.
BKR1-(Name) SELECTED This message is displayed after the USER 1 key is pressed for the second time. Three
USER 2=CLS/USER 3=OP possible actions can be performed from this state within 30 seconds as per items (1), (2)
and (3) below:
(1)
USER 2 OFF/ON If the USER 2 key is pressed, this message appears for 20 seconds. If the USER 2 key is
To Close BKR1-(Name) pressed again within that time, a signal is created that can be programmed to operate an
output relay to close breaker 1.
(2)
USER 3 OFF/ON If the USER 3 key is pressed, this message appears for 20 seconds. If the USER 3 key is
To Open BKR1-(Name) pressed again within that time, a signal is created that can be programmed to operate an
output relay to open breaker 1.
(3)
BKR2-(Name) SELECTED If the USER 1 key is pressed at this step, this message appears showing that a different
USER 2=CLS/USER 3=OP breaker is selected. Three possible actions can be performed from this state as per (1),
(2) and (3). Repeatedly pressing the USER 1 key alternates between available breakers.
Pressing keys other than USER 1, 2, or 3 at any time aborts the breaker control function.
e) CONTROL OF ONE BREAKER

For this application the relay is connected and programmed for breaker 1 only. Operation for this application is identical to
that described above for two breakers.
4.3.7 MENUS
a) NAVIGATION
Press the MENU key to select a header display page (top-level menu). The header title appears momentarily followed by a
header display page menu item. Each press of the MENU key advances through the following main heading pages:
• Actual values
• Settings
• Commands
• Targets
• User displays (when enabled)

b) HIERARCHY
The setting and actual value messages are arranged hierarchically. The header display pages are indicated by double
scroll bar characters (), while sub-header pages are indicated by single scroll bar characters (). The header display
pages represent the highest level of the hierarchy and the sub-header display pages fall below this level. The MESSAGE
UP and DOWN keys move within a group of headers, sub-headers, setting values, or actual values. Continually pressing
the MESSAGE RIGHT key from a header display displays specific information for the header category. Conversely, contin-
ually pressing the MESSAGE LEFT key from a setting value or actual value display returns to the header display.
HIGHEST LEVEL LOWEST LEVEL (SETTING

VALUE)
 SETTINGS  PASSWORD ACCESS LEVEL:

 PRODUCT SETUP  SECURITY Restricted
 SETTINGS
 SYSTEM SETUP
c) EXAMPLE MENU NAVIGATION 4

 ACTUAL VALUES Press the MENU key until the header for the first Actual Values page appears. This
 STATUS page contains system and relay status information. Repeatedly press the MESSAGE
keys to display the other actual value headers.

 SETTINGS Press the MENU key until the header for the first page of Settings appears. This page
 PRODUCT SETUP contains settings to configure the relay.

 SETTINGS Press the MESSAGE DOWN key to move to the next Settings page. This page con-
 SYSTEM SETUP tains settings for System Setup. Repeatedly press the MESSAGE UP and DOWN
keys to display the other setting headers and then back to the first Settings page
header.

 PASSWORD From the Settings page one header (Product Setup), press the MESSAGE RIGHT
 SECURITY key once to display the first sub-header (Password Security).

ACCESS LEVEL: Press the MESSAGE RIGHT key once more and this will display the first setting for
Restricted Password Security. Pressing the MESSAGE DOWN key repeatedly will display the
 remaining setting messages for this sub-header.
 PASSWORD Press the MESSAGE LEFT key once to move back to the first sub-header message.
 SECURITY

 DISPLAY Pressing the MESSAGE DOWN key displays the second setting sub-header associ-
 PROPERTIES ated with the Product Setup header.

FLASH MESSAGE Press the MESSAGE RIGHT key once more to display the first setting for Display
TIME: 1.0 s Properties.

DEFAULT MESSAGE To view the remaining settings associated with the Display Properties subheader,
INTENSITY: 25% repeatedly press the MESSAGE DOWN key. The last message appears as shown.

4.3.8 CHANGING SETTINGS
a) ENTERING NUMERICAL DATA

Each numerical setting has its own minimum, maximum, and increment value associated with it. These parameters define
what values are acceptable for a setting.
FLASH MESSAGE For example, select the SETTINGS  PRODUCT SETUP  DISPLAY PROPERTIES  FLASH
TIME: 1.0 s MESSAGE TIME setting.

MINIMUM: 0.5 Press the HELP key to view the minimum and maximum values. Press the HELP key
MAXIMUM: 10.0 again to view the next context sensitive help message.
Two methods of editing and storing a numerical setting value are available.
• 0 to 9 and decimal point: The relay numeric keypad works the same as that of any electronic calculator. A number is
entered one digit at a time. The leftmost digit is entered first and the rightmost digit is entered last. Pressing the MES-
SAGE LEFT key or pressing the ESCAPE key, returns the original value to the display.
• VALUE keys: The VALUE UP key increments the displayed value by the step value, up to the maximum value allowed.
4 While at the maximum value, pressing the VALUE UP key again allows the setting selection to continue upward from
the minimum value. The VALUE DOWN key decrements the displayed value by the step value, down to the minimum
value. While at the minimum value, pressing the VALUE DOWN key again allows the setting selection to continue
downward from the maximum value.
FLASH MESSAGE As an example, set the flash message time setting to 2.5 seconds. Press the appropriate
TIME: 2.5 s numeric keys in the sequence “2 . 5". The display message changes as the digits are
 being entered.
NEW SETTING Until ENTER is pressed, editing changes are not registered by the relay. Therefore, press
HAS BEEN STORED ENTER to store the new value in memory. This flash message momentarily appears as
confirmation of the storing process. Numerical values which contain decimal places are
rounded-off if more decimal place digits are entered than specified by the step value.
b) ENTERING ENUMERATION DATA

Enumeration settings have data values which are part of a set, whose members are explicitly defined by a name. A set is
comprised of two or more members.
ACCESS LEVEL: For example, the selections available for ACCESS LEVEL are "Restricted", "Command",
Restricted "Setting", and "Factory Service".
Enumeration type values are changed using the VALUE keys. The VALUE UP key displays the next selection while the
VALUE DOWN key displays the previous selection.
ACCESS LEVEL: If the ACCESS LEVEL needs to be "Setting", press the VALUE keys until the proper selec-
Setting tion is displayed. Press HELP at any time for the context sensitive help messages.

NEW SETTING Changes are not registered by the relay until the ENTER key is pressed. Pressing
HAS BEEN STORED ENTER stores the new value in memory. This flash message momentarily appears as
confirmation of the storing process.
c) ENTERING ALPHANUMERIC TEXT

Text settings have data values which are fixed in length, but user-defined in character. They can be upper case letters,
lower case letters, numerals, and a selection of special characters.

There are several places where text messages can be programmed to allow the relay to be customized for specific applica-
tions. One example is the Message Scratchpad. Use the following procedure to enter alphanumeric text messages.
For example: to enter the text, “Breaker #1”.
1. Press the decimal point to enter text edit mode.
2. Press the VALUE keys until the character 'B' appears; press the decimal key to advance the cursor to the next position.
3. Repeat step 2 for the remaining characters: r,e,a,k,e,r, ,#,1.
4. Press ENTER to store the text.
5. If you have any problem, press HELP to view context sensitive help. Flash messages appear sequentially for several
seconds each. For the case of a text setting message, pressing HELP displays how to edit and store new values.
d) ACTIVATING THE RELAY
RELAY SETTINGS: When the relay is powered up, the Trouble LED is on, the In Service LED off, and this
Not Programmed message displayed, indicating the relay is in the "Not Programmed" state and is safe-
guarding (output relays blocked) against the installation of a relay whose settings have
not been entered. This message remains until the relay is explicitly put in the "Pro-
grammed" state.
4
To change the RELAY SETTINGS: "Not Programmed" mode to "Programmed", proceed as follows:
1. Press the MENU key until the SETTINGS header flashes momentarily and the PRODUCT SETUP message appears on the
display.
2. Press the MESSAGE RIGHT key until the PASSWORD SECURITY message appears on the display.
3. Press the MESSAGE DOWN key until the INSTALLATION message appears on the display.
4. Press the MESSAGE RIGHT key until the RELAY SETTINGS: Not Programmed message is displayed.
SETTINGS

 SETTINGS  PASSWORD
 PRODUCT SETUP  SECURITY
 DISPLAY
 PROPERTIES

 INSTALLATION RELAY SETTINGS:

 Not Programmed
5. After the RELAY SETTINGS: Not Programmed message appears on the display, press the VALUE keys change the
selection to "Programmed".
6. Press the ENTER key.
RELAY SETTINGS: RELAY SETTINGS: NEW SETTING

Not Programmed Programmed HAS BEEN STORED
7. When the "NEW SETTING HAS BEEN STORED" message appears, the relay is in "Programmed" state and the In
Service LED turns on.
e) ENTERING INITIAL PASSWORDS

The information in this section refers to password security. For information on how to set or change CyberSentry pass-
words, see the Settings > Product Setup > Security > CyberSentry section in the next chapter.

The D60 supports password entry from a local or remote connection.

Local access is defined as any access to settings or commands via the faceplate interface. This includes both keypad entry
and the faceplate RS232 connection. Remote access is defined as any access to settings or commands via any rear com-
munications port. This includes both Ethernet and RS485 connections. Any changes to the local or remote passwords
enables this functionality.
To enter the initial setting (or command) password, proceed as follows:
1. Press the MENU key until the SETTINGS header flashes momentarily and the PRODUCT SETUP message appears on the
display.
2. Press the MESSAGE RIGHT key until the ACCESS LEVEL message appears on the display.
3. Press the MESSAGE DOWN key until the CHANGE LOCAL PASSWORDS message appears on the display.
4. Press the MESSAGE RIGHT key until the CHANGE SETTING PASSWORD or CHANGE COMMAND PASSWORD message
appears on the display.
 PASSWORD ACCESS LEVEL:
 SECURITY Restricted
 CHANGE LOCAL CHANGE COMMAND
 PASSWORDS PASSWORD: No
4 CHANGE SETTING
PASSWORD: No
ENCRYPTED COMMAND
PASSWORD: ---------
ENCRYPTED SETTING
PASSWORD: ---------
5. After the CHANGE...PASSWORD message appears on the display, press the VALUE UP or DOWN key to change the
selection to “Yes”.
6. Press the ENTER key and the display prompts you to ENTER NEW PASSWORD.
7. Type in a numerical password (up to 10 characters) and press the ENTER key.
8. When the VERIFY NEW PASSWORD is displayed, re-type in the same password and press ENTER.
CHANGE SETTING
PASSWORD: No
CHANGE SETTING ENTER NEW VERIFY NEW

PASSWORD: Yes PASSWORD: ########## PASSWORD: ##########
NEW PASSWORD
HAS BEEN STORED
9. When the NEW PASSWORD HAS BEEN STORED message appears, your new Setting (or Command) Password will be
active.
f) CHANGING EXISTING PASSWORD

To change an existing password, follow the instructions in the previous section with the following exception. A message
prompts you to type in the existing password (for each security level) before a new password can be entered.
g) INVALID PASSWORD ENTRY

When an incorrect command or setting password has been entered via the faceplate interface three times within a 3-minute
time span, the LOCAL ACCESS DENIED FlexLogic operand is set to “On” and the D60 does not allow settings or command
level access via the faceplate interface for the next five minutes, or in the event that an incorrect Command Or Setting
password has been entered via the any external communications interface three times within a 3-minute time span, the
REMOTE ACCESS DENIED FlexLogic operand is set to “On” and the D60 does not allow settings or command access via the
any external communications interface for the next five minutes.

In the event that an incorrect Command or Setting password has been entered via the any external communications inter-
face three times within a three-minute time span, the REMOTE ACCESS DENIED FlexLogic operand is set to “On” and the
D60 does not allow Settings or Command access via the any external communications interface for the next ten minutes.
The REMOTE ACCESS DENIED FlexLogic operand is set to “Off” after the expiration of the ten-minute timeout.


5 SETTINGS 5.1 OVERVIEW
5 SETTINGS 5.1OVERVIEW 5.1.1 SETTINGS MENU
 SETTINGS  SECURITY
See page 5-8.
 PRODUCT SETUP 
 DISPLAY
See page 5-23.
 PROPERTIES
 CLEAR RELAY
See page 5-25.
 RECORDS
 COMMUNICATIONS
See page 5-26.

 MODBUS USER MAP
See page 5-55.

 REAL TIME
See page 5-56.
 CLOCK
 FAULT REPORTS
See page 5-60.

 OSCILLOGRAPHY
See page 5-62.

 DATA LOGGER
See page 5-64.

5
 USER-PROGRAMMABLE
See page 5-66.
 LEDS
See page 5-69.
 SELF TESTS
 CONTROL
See page 5-69.
 PUSHBUTTONS
See page 5-71.
 PUSHBUTTONS
 FLEX STATE
See page 5-76.
 PARAMETERS
 USER-DEFINABLE
See page 5-77.
 DISPLAYS
 DIRECT I/O
See page 5-79.

 TELEPROTECTION
See page 5-87.

 INSTALLATION
See page 5-87.

 SETTINGS  AC INPUTS
See page 5-90.
 SYSTEM SETUP 
 POWER SYSTEM
See page 5-91.

 SIGNAL SOURCES
See page 5-92.


5.1 OVERVIEW 5 SETTINGS
 BREAKERS
See page 5-95.

 SWITCHES
See page 5-99.

 FLEXCURVES
See page 5-102.

 PHASOR MEASUREMENT
See page 5-109.
 UNIT
 SETTINGS  FLEXLOGIC
See page 5-149.
 FLEXLOGIC  EQUATION EDITOR
 FLEXLOGIC
See page 5-149.
 TIMERS
 FLEXELEMENTS
See page 5-150.

 NON-VOLATILE
See page 5-154.
 LATCHES
 SETTINGS  SETTING GROUP 1

See page 5-155.
 GROUPED ELEMENTS 
5  SETTING GROUP 2


 SETTING GROUP 6

 SETTINGS  TRIP BUS

See page 5-240.
 CONTROL ELEMENTS 
 SETTING GROUPS
See page 5-242.

 SELECTOR SWITCH
See page 5-244.

 TRIP OUTPUT
See page 5-250.

 UNDERFREQUENCY
See page 5-256.

 OVERFREQUENCY
See page 5-257.

 FREQUENCY RATE
See page 5-258.
 OF CHANGE
 SYNCHROCHECK
See page 5-260.

 AUTORECLOSE
See page 5-264.


 DIGITAL ELEMENTS
See page 5-277.

 DIGITAL COUNTERS
See page 5-280.

 MONITORING
See page 5-282.
 ELEMENTS
 PILOT SCHEMES
See page 5-302.

 SETTINGS  CONTACT INPUTS

See page 5-326.
 INPUTS / OUTPUTS 
 VIRTUAL INPUTS
See page 5-328.

 CONTACT OUTPUTS
See page 5-329.

 VIRTUAL OUTPUTS
See page 5-331.

 REMOTE DEVICES
See page 5-332.

 REMOTE INPUTS

See page 5-333.
5
 REMOTE DPS INPUTS
See page 5-334.

 REMOTE OUTPUTS
See page 5-334.
 DNA BIT PAIRS
 REMOTE OUTPUTS
See page 5-335.
 UserSt BIT PAIRS
 RESETTING
See page 5-335.

 DIRECT INPUTS
See page 5-336.

 DIRECT OUTPUTS
See page 5-336.

 TELEPROTECTION
See page 5-339.

 IEC 61850
See page 5-341.
 GOOSE ANALOGS
 IEC 61850
See page 5-342.
 GOOSE UINTEGERS
 SETTINGS  DCMA INPUTS

See page 5-343.
 TRANSDUCER I/O 
 RTD INPUTS
See page 5-344.


 DCMA OUTPUTS
See page 5-346.

 SETTINGS TEST MODE

See page 5-349.
 TESTING FUNCTION: Disabled
TEST MODE FORCING:
See page 5-349.
On
 FORCE CONTACT
See page 5-350.
 INPUTS
 FORCE CONTACT
See page 5-351.
 OUTPUTS
 PMU
See page 5-352.
 TEST VALUES
5.1.2 INTRODUCTION TO ELEMENTS
In the design of UR relays, the term element is used to describe a feature that is based around a comparator. The compar-
ator is provided with an input (or set of inputs) that is tested against a programmed setting (or group of settings) to deter-
mine if the input is within the defined range that will set the output to logic 1, also referred to as setting the flag. A single
comparator may make multiple tests and provide multiple outputs; for example, the time overcurrent comparator sets a
pickup flag when the current input is above the setting and sets an operate flag when the input current has been at a level
5 above the pickup setting for the time specified by the time-current curve settings. All comparators use analog parameter
actual values as the input.
The exception to the above rule are the digital elements, which use logic states as inputs.
NOTE
Elements are arranged into two classes, grouped and control. Each element classed as a grouped element is provided with
six alternate sets of settings, in setting groups numbered 1 through 6. The performance of a grouped element is defined by
the setting group that is active at a given time. The performance of a control element is independent of the selected active
setting group.
The main characteristics of an element are shown on the element logic diagram. This includes the inputs, settings, fixed
logic, and the output operands generated (abbreviations used on scheme logic diagrams are defined in Appendix F).
Some settings for current and voltage elements are specified in per-unit (pu) calculated quantities:
pu quantity = (actual quantity) / (base quantity)
For current elements, the base quantity is the nominal secondary or primary current of the CT.
Where the current source is the sum of two CTs with different ratios, the base quantity will be the common secondary or pri-
mary current to which the sum is scaled (that is, normalized to the larger of the two rated CT inputs). For example, if CT1 =
300 / 5 A and CT2 = 100 / 5 A, then in order to sum these, CT2 is scaled to the CT1 ratio. In this case, the base quantity will
be 5 A secondary or 300 A primary.
For voltage elements the base quantity is the nominal primary voltage of the protected system which corresponds (based
on VT ratio and connection) to secondary VT voltage applied to the relay.
For example, on a system with a 13.8 kV nominal primary voltage and with 14400:120 V delta-connected VTs, the second-
ary nominal voltage (1 pu) would be:
13800
----------------  120 = 115 V (EQ 5.1)
14400
For wye-connected VTs, the secondary nominal voltage (1 pu) would be:
13800
----------------  120
---------- = 66.4 V (EQ 5.2)
14400 3

Many settings are common to most elements and are discussed below:
• FUNCTION setting: This setting programs the element to be operational when selected as “Enabled”. The factory
default is “Disabled”. Once programmed to “Enabled”, any element associated with the function becomes active and all
options become available.
• NAME setting: This setting is used to uniquely identify the element.
• SOURCE setting: This setting is used to select the parameter or set of parameters to be monitored.
• PICKUP setting: For simple elements, this setting is used to program the level of the measured parameter above or
below which the pickup state is established. In more complex elements, a set of settings may be provided to define the
range of the measured parameters which will cause the element to pickup.
• PICKUP DELAY setting: This setting sets a time-delay-on-pickup, or on-delay, for the duration between the pickup
and operate output states.
• RESET DELAY setting: This setting is used to set a time-delay-on-dropout, or off-delay, for the duration between the
Operate output state and the return to logic 0 after the input transits outside the defined pickup range.
• BLOCK setting: The default output operand state of all comparators is a logic 0 or “flag not set”. The comparator
remains in this default state until a logic 1 is asserted at the RUN input, allowing the test to be performed. If the RUN
input changes to logic 0 at any time, the comparator returns to the default state. The RUN input is used to supervise
the comparator. The BLOCK input is used as one of the inputs to RUN control.
• TARGET setting: This setting is used to define the operation of an element target message. When set to “Disabled”,
no target message or illumination of a faceplate LED indicator is issued upon operation of the element. When set to
“Self-Reset”, the target message and LED indication follow the operate state of the element, and self-resets once the
operate element condition clears. When set to “Latched”, the target message and LED indication will remain visible
after the element output returns to logic 0 until a RESET command is received by the relay.
• EVENTS setting: This setting is used to control whether the pickup, dropout or operate states are recorded by the 5
event recorder. When set to “Disabled”, element pickup, dropout or operate are not recorded as events. When set to
“Enabled”, events are created for:
(Element) PKP (pickup)
(Element) DPO (dropout)
(Element) OP (operate)
The DPO event is created when the measure and decide comparator output transits from the pickup state (logic 1) to
the dropout state (logic 0). This could happen when the element is in the operate state if the reset delay time is not 0.
5.1.3 INTRODUCTION TO AC SOURCES
a) BACKGROUND
The D60 may be used on systems with breaker-and-a-half or ring bus configurations. In these applications, each of the two
three-phase sets of individual phase currents (one associated with each breaker) can be used as an input to a breaker fail-
ure element. The sum of both breaker phase currents and 3I_0 residual currents may be required for the circuit relaying
and metering functions. For a three-winding transformer application, it may be required to calculate watts and vars for each
of three windings, using voltage from different sets of VTs. These requirements can be satisfied with a single UR, equipped
with sufficient CT and VT input channels, by selecting the parameter to measure. A mechanism is provided to specify the
AC parameter (or group of parameters) used as the input to protection/control comparators and some metering elements.
Selection of the parameter(s) to measure is partially performed by the design of a measuring element or protection/control
comparator by identifying the type of parameter (fundamental frequency phasor, harmonic phasor, symmetrical component,
total waveform RMS magnitude, phase-phase or phase-ground voltage, etc.) to measure. The user completes the process
by selecting the instrument transformer input channels to use and some of the parameters calculated from these channels.
The input parameters available include the summation of currents from multiple input channels. For the summed currents of
phase, 3I_0, and ground current, current from CTs with different ratios are adjusted to a single ratio before summation.
A mechanism called a source configures the routing of CT and VT input channels to measurement sub-systems. Sources,
in the context of UR series relays, refer to the logical grouping of current and voltage signals such that one source contains
all the signals required to measure the load or fault in a particular power apparatus. A given source may contain all or some
of the following signals: three-phase currents, single-phase ground current, three-phase voltages and an auxiliary voltage
from a single VT for checking for synchronism.

To illustrate the concept of sources, as applied to current inputs only, consider the breaker-and-a-half scheme below. In this
application, the current flows as shown by the arrows. Some current flows through the upper bus bar to some other location
or power equipment, and some current flows into transformer winding 1. The current into winding 1 is the phasor sum (or
difference) of the currents in CT1 and CT2 (whether the sum or difference is used depends on the relative polarity of the CT
connections). The same considerations apply to transformer winding 2. The protection elements require access to the net
current for transformer protection, but some elements may need access to the individual currents from CT1 and CT2.
CT1 through current CT2
Winding 1
current
Winding 1
UR-series
relay Power
transformer
Winding 2
CT3 CT4
827791A3.CDR
Figure 5–1: BREAKER-AND-A-HALF SCHEME

In conventional analog or electronic relays, the sum of the currents is obtained from an appropriate external connection of
5 all CTs through which any portion of the current for the element being protected could flow. Auxiliary CTs are required to
perform ratio matching if the ratios of the primary CTs to be summed are not identical. In the UR series of relays, provisions
have been included for all the current signals to be brought to the UR device where grouping, ratio correction and summa-
tion are applied internally via configuration settings.
A major advantage of using internal summation is that the individual currents are available to the protection device; for
example, as additional information to calculate a restraint current, or to allow the provision of additional protection features
that operate on the individual currents such as breaker failure.
Given the flexibility of this approach, it becomes necessary to add configuration settings to the platform to allow the user to
select which sets of CT inputs will be added to form the net current into the protected device.
The internal grouping of current and voltage signals forms an internal source. This source can be given a specific name
through the settings, and becomes available to protection and metering elements in the UR platform. Individual names can
be given to each source to help identify them more clearly for later use. For example, in the scheme shown in the above
diagram, the user configures one source to be the sum of CT1 and CT2 and can name this source as “Wdg1 I”.
Once the sources have been configured, the user has them available as selections for the choice of input signal for the pro-
tection elements and as metered quantities.
b) CT/VT MODULE CONFIGURATION

CT and VT input channels are contained in CT/VT modules. The type of input channel can be phase/neutral/other voltage,
phase/ground current, or sensitive ground current. The CT/VT modules calculate total waveform RMS levels, fundamental
frequency phasors, symmetrical components and harmonics for voltage or current, as allowed by the hardware in each
channel. These modules may calculate other parameters as directed by the CPU module.
A CT/VT module contains up to eight input channels, numbered 1 through 8. The channel numbering corresponds to the
module terminal numbering 1 through 8 and is arranged as follows: Channels 1, 2, 3 and 4 are always provided as a group,
hereafter called a “bank,” and all four are either current or voltage, as are channels 5, 6, 7 and 8. Channels 1, 2, 3 and 5, 6,
7 are arranged as phase A, B and C respectively. Channels 4 and 8 are either another current or voltage.

Banks are ordered sequentially from the block of lower-numbered channels to the block of higher-numbered channels, and
from the CT/VT module with the lowest slot position letter to the module with the highest slot position letter, as follows:
INCREASING SLOT POSITION LETTER -->
CT/VT MODULE 1 CT/VT MODULE 2 CT/VT MODULE 3
< bank 1 > < bank 3 > < bank 5 >
< bank 2 > < bank 4 > < bank 6 >
The UR platform allows for a maximum of three sets of three-phase voltages and six sets of three-phase currents. The
result of these restrictions leads to the maximum number of CT/VT modules in a chassis to three. The maximum number of
sources is six. A summary of CT/VT module configurations is shown below.
ITEM MAXIMUM NUMBER
CT/VT Module 2
CT Bank (3 phase channels, 1 ground channel) 4
VT Bank (3 phase channels, 1 auxiliary channel) 2
c) CT/VT INPUT CHANNEL CONFIGURATION

Upon relay startup, configuration settings for every bank of current or voltage input channels in the relay are automatically
generated from the order code. Within each bank, a channel identification label is automatically assigned to each bank of
channels in a given product. The bank naming convention is based on the physical location of the channels, required by the
user to know how to connect the relay to external circuits. Bank identification consists of the letter designation of the slot in
which the CT/VT module is mounted as the first character, followed by numbers indicating the channel, either 1 or 5.
For three-phase channel sets, the number of the lowest numbered channel identifies the set. For example, F1 represents
the three-phase channel set of F1/F2/F3, where F is the slot letter and 1 is the first channel of the set of three channels.
Upon startup, the CPU configures the settings required to characterize the current and voltage inputs, and will display them
5
in the appropriate section in the sequence of the banks (as described above) as follows for a maximum configuration: F1,
F5, M1, M5, U1, and U5.
The above section explains how the input channels are identified and configured to the specific application instrument
transformers and the connections of these transformers. The specific parameters to be used by each measuring element
and comparator, and some actual values are controlled by selecting a specific source. The source is a group of current and
voltage input channels selected by the user to facilitate this selection. With this mechanism, a user does not have to make
multiple selections of voltage and current for those elements that need both parameters, such as a distance element or a
watt calculation. It also gathers associated parameters for display purposes.
The basic idea of arranging a source is to select a point on the power system where information is of interest. An applica-
tion example of the grouping of parameters in a source is a transformer winding, on which a three phase voltage is mea-
sured, and the sum of the currents from CTs on each of two breakers is required to measure the winding current flow.

5.2 PRODUCT SETUP 5 SETTINGS
5.2PRODUCT SETUP 5.2.1 SECURITY
a) SECURITY OVERVIEW
The following security features are available:
• Password security — Basic security present in the default offering of the product
• EnerVista security — Role-based access to various EnerVista software screens and configuration elements. The fea-
ture is available in the default offering of the product and only in the EnerVista software.
• CyberSentry security — Advanced security options available as a software option. When purchased, the options are
automatically enabled, and the default Password security and EnerVista security are disabled.
b) LOST PASSWORD
If all passwords are lost, recovery is possible by resetting the unit to default values.
To reset the unit after a lost password:
1. Email GE customer service at multilin.tech@ge.com with the serial number and using a recognizable corporate email
account. Customer service provides a code to reset the relay to the factory defaults.
2. Enter the reset code on the front panel, under Commands > Commands Relay Maintenance > Service Command.
3. Change the default password of ChangeMe1# as outlined in the Set Up CyberSentry and Change Default Password
section in the first chapter.
c) PASSWORD REQUIREMENTS
For password security and CyberSentry security, a user account requires an alpha-numeric password that meets the follow-
5 ing requirements:
• Password is case-sensitive
• Password cannot contain the user account name or parts of the user account that exceed two consecutive characters
• Password must be 6 to 20 characters in length
• Password must contain characters from three of the following four categories:
- English uppercase characters (A through Z)
- English lowercase characters (a through z)
- Base 10 digits (0 through 9)
- Non-alphabetic characters (for example, ~, !, @, #, $,%, &)
d) PASSWORD SECURITY
PATH: SETTINGS  PRODUCT SETUP  SECURITY
 SECURITY ACCESS LEVEL: Range: Restricted, Command, Setting,

 Restricted Factory Service (for factory use only)
 CHANGE LOCAL
MESSAGE See page 5–9.
 PASSWORDS
 ACCESS
 SUPERVISION
 DUAL PERMISSION
 SECURITY ACCESS
PASSWORD ACCESS Range: Disabled, Enabled
MESSAGE
EVENTS: Disabled

5 SETTINGS 5.2 PRODUCT SETUP
and the through the faceplate RS232 port. Remote access is defined as any access to settings or commands via any rear
communications port. This includes both Ethernet and RS485 connections. Any changes to the local or remote passwords
is to the RS232 port of the faceplate, the local password must be used.
The PASSWORD ACCESS EVENTS settings allows recording of password access events in the event recorder.
The local setting and command sessions are initiated by the user through the front panel display and are disabled either by
the user or by timeout (via the setting and command level access timeout settings). The remote setting and command ses-
sions are initiated by the user through the EnerVista UR Setup software and are disabled either by the user or by timeout.
The state of the session (local or remote, setting or command) determines the state of the following FlexLogic operands.
• ACCESS LOC SETG OFF: Asserted when local setting access is disabled
• ACCESS LOC SETG ON: Asserted when local setting access is enabled
• ACCESS LOC CMND OFF: Asserted when local command access is disabled
• ACCESS LOC CMND ON: Asserted when local command access is enabled
• ACCESS REM SETG OFF: Asserted when remote setting access is disabled
• ACCESS REM SETG ON: Asserted when remote setting access is enabled
• ACCESS REM CMND OFF: Asserted when remote command access is disabled
• ACCESS REM CMND ON: Asserted when remote command access is enabled
A command or setting write operation is required to update the state of all the remote and local security operands 5
shown above.
NOTE
LOCAL PASSWORDS
PATH: SETTINGS  PRODUCT SETUP  SECURITY  CHANGE LOCAL PASSWORDS
 CHANGE LOCAL CHANGE COMMAND Range: No, Yes

 PASSWORDS PASSWORD: No
CHANGE SETTING Range: No, Yes
MESSAGE
PASSWORD: No
ENCRYPTED COMMAND Range: 0 to 9999999999
MESSAGE Note: ---------- indicates no password
PASSWORD: ----------
ENCRYPTED SETTING Range: 0 to 9999999999
MESSAGE Note: ---------- indicates no password
PASSWORD: ----------
Proper password codes are required to enable each access level. When a CHANGE COMMAND PASSWORD or CHANGE SET-
TING PASSWORD setting is programmed to “Yes” via the front panel interface, the following message sequence is invoked:
1. ENTER NEW PASSWORD: ____________.

2. VERIFY NEW PASSWORD: ____________.
3. NEW PASSWORD HAS BEEN STORED.
To gain write access to a “Restricted” setting, program the ACCESS LEVEL setting in the main security menu to “Setting” and
then change the setting, or attempt to change the setting and follow the prompt to enter the programmed password. If the
password is correctly entered, access will be allowed. Accessibility automatically reverts to the “Restricted” level according
to the access level timeout setting values.
If the setting and command passwords are identical, then this one password allows access to both commands and
settings.
NOTE

If a remote connection is established, local passcodes are not visible.
NOTE
REMOTE PASSWORDS
The remote password settings are visible only from a remote connection via the EnerVista UR Setup software.
Proper passwords are required to enable each command or setting level access.
To set the command or setting password:
1. In the EnerVista software, navigate to Settings > Product Setup > Security menu item to open the remote password
settings window.
2. Click the command or setting password Change button.
3. Enter the new password in the New Password field. Requirements are outlined in the Password Requirements section
at the beginning of the chapter. When an original password has already been used, enter it in the Enter Password
field and click the Send Password to Device button.
4. Re-enter the password in the Confirm Password field.
5. Click the OK button. The password is checked to ensure that is meets requirements.
If you establish a local connection to the relay (serial), you cannot view remote passcodes.
NOTE
ACCESS SUPERVISION
PATH: SETTINGS  PRODUCT SETUP  SECURITY  ACCESS SUPERVISION
 ACCESS  ACCESS LEVEL

 SUPERVISION  TIMEOUTS
INVALID ATTEMPTS Range: 2 to 5 in steps of 1
MESSAGE
BEFORE LOCKOUT: 3
PASSWORD LOCKOUT Range: 5 to 60 minutes in steps of 1
MESSAGE
DURATION: 5 min
The following access supervision settings are available.

• INVALID ATTEMPTS BEFORE LOCKOUT: This setting specifies the number of times an incorrect password can be
entered within a three-minute time span before lockout occurs. When lockout occurs, the LOCAL ACCESS DENIED or
REMOTE ACCESS DENIED FlexLogic operands are set to “On”. These operands are returned to the “Off” state upon
expiration of the lockout.
• PASSWORD LOCKOUT DURATION: This setting specifies the time that the D60 will lockout password access after
the number of invalid password entries specified by the INVALID ATTEMPTS BEFORE LOCKOUT setting has occurred.
The D60 provides a means to raise an alarm upon failed password entry. Should password verification fail while accessing
a password-protected level of the relay (either settings or commands), the UNAUTHORIZED ACCESS FlexLogic operand is
asserted. The operand can be programmed to raise an alarm via contact outputs or communications. This feature can be
used to protect against both unauthorized and accidental access attempts.

The UNAUTHORIZED ACCESS operand is reset with the COMMANDS  CLEAR RECORDS  RESET UNAUTHORIZED
ALARMS command. Therefore, to apply this feature with security, the command level should be password-protected. The
operand does not generate events or targets.
If events or targets are required, the UNAUTHORIZED ACCESS operand can be assigned to a digital element programmed
with event logs or targets enabled.
The access level timeout settings are shown below.
PATH: SETTINGS  PRODUCT SETUP  SECURITY  ACCESS SUPERVISION  ACCESS LEVEL TIMEOUTS
 ACCESS LEVEL COMMAND LEVEL ACCESS Range: 5 to 480 minutes in steps of 1

 TIMEOUTS TIMEOUT: 5 min
SETTING LEVEL ACCESS Range: 5 to 480 minutes in steps of 1
MESSAGE
TIMEOUT: 30 min
These settings allow the user to specify the length of inactivity required before returning to the restricted access level. Note
that the access level will set as restricted if control power is cycled.
• COMMAND LEVEL ACCESS TIMEOUT: This setting specifies the length of inactivity (no local or remote access)
required to return to restricted access from the command password level.
• SETTING LEVEL ACCESS TIMEOUT: This setting specifies the length of inactivity (no local or remote access)
required to return to restricted access from the command password level.
DUAL PERMISSION SECURITY ACCESS
PATH: SETTINGS  PRODUCT SETUP  SECURITY  DUAL PERMISSION SECURITY ACCESS
 DUAL PERMISSION LOCAL SETTING AUTH: Range: selected FlexLogic operands (see below)
 SECURITY ACCESS On 5
REMOTE SETTING AUTH: Range: FlexLogic operand
MESSAGE
On
ACCESS AUTH Range: 5 to 480 minutes in steps of 1
MESSAGE
TIMEOUT: 30 min.
The dual permission security access feature provides a mechanism for customers to prevent unauthorized or unintended
upload of settings to a relay through the local or remote interfaces interface.
The following settings are available through the local (front panel) interface only.
• LOCAL SETTING AUTH: This setting is used for local (front panel or RS232 interface) setting access supervision.
Valid values for the FlexLogic operands are either “On” (default) or any physical “Contact Input ~~ On” value.
If this setting is “On“, then local setting access functions as normal; that is, a local setting password is required. If this
setting is any contact input on FlexLogic operand, then the operand must be asserted (set as on) prior to providing the
local setting password to gain setting access.
If setting access is not authorized for local operation (front panel or RS232 interface) and the user attempts to obtain
setting access, then the UNAUTHORIZED ACCESS message is displayed on the front panel.
• REMOTE SETTING AUTH: This setting is used for remote (Ethernet or RS485 interfaces) setting access supervision.
If this setting is “On” (the default setting), then remote setting access functions as normal; that is, a remote password is
required). If this setting is “Off”, then remote setting access is blocked even if the correct remote setting password is
provided. If this setting is any other FlexLogic operand, then the operand must be asserted (set as on) prior to provid-
ing the remote setting password to gain setting access.
• ACCESS AUTH TIMEOUT: This setting represents the timeout delay for local setting access. This setting is applicable
when the LOCAL SETTING AUTH setting is programmed to any operand except “On”. The state of the FlexLogic operand
is continuously monitored for an off-to-on transition. When this occurs, local access is permitted and the timer pro-
grammed with the ACCESS AUTH TIMEOUT setting value is started. When this timer expires, local setting access is
immediately denied. If access is permitted and an off-to-on transition of the FlexLogic operand is detected, the timeout
is restarted. The status of this timer is updated every 5 seconds.

The following settings are available through the remote (EnerVista UR Setup) interface only. Select the Settings > Product
Setup > Security menu item to display the security settings window.
The Remote Settings Authorized setting is used for remote (Ethernet or RS485 interfaces) setting access supervision. If
this setting is “On” (the default setting), then remote setting access functions as normal; that is, a remote password is
required). If this setting is “Off”, then remote setting access is blocked even if the correct remote setting password is pro-
vided. If this setting is any other FlexLogic operand, then the operand must be asserted (set as on) prior to providing the
5 remote setting password to gain setting access.

The Access Authorized Timeout setting represents the timeout delay remote setting access. This setting is applicable
when the Remote Settings Authorized setting is programmed to any operand except “On” or “Off”. The state of the Flex-
Logic operand is continuously monitored for an off-to-on transition. When this occurs, remote setting access is permitted
and the timer programmed with the Access Authorized Timeout setting value is started. When this timer expires, remote
setting access is immediately denied. If access is permitted and an off-to-on transition of the FlexLogic operand is detected,
the timeout is restarted. The status of this timer is updated every 5 seconds.
e) ENERVISTA SECURITY
ENABLING THE SECURITY MANAGEMENT SYSTEM
The EnerVista security system allows an administrator to manage access privileges of multiple users to the EnerVista appli-
cation.
It is disabled by default to allow the administrator direct access to the EnerVista software immediately after installation.
When security is disabled, all users have administrator access. GE recommends enabling the EnerVista security before
placing the device in service.
To enable the security system and require password use:

1. Select the Security > User Management menu item to open the user management window.
2. Check the Enable Security box in the lower-left corner to enable the security management system.
Security is now enabled for the EnerVista UR Setup software. Upon starting the software, users are now required to enter a
username and password.
ADDING A NEW USER
The following pre-requisites are required to add user accounts to the EnerVista security management system: 5
• The user adding the account must have administrator rights
• The EnerVista security management system must be enabled (previous section)
To add user accounts:
1. Select the Security > User Management menu item to open the user management window.
2. Enter a username in the User field. The username must be 4 to 20 characters in length.
3. Select the user access rights by enabling the check box of one or more of the fields.

The table outlines access rights.

Table 5–1: ACCESS RIGHTS SUMMARY
FIELD DESCRIPTION
Delete Entry Deletes the user account when exiting the user management window
Actual Values Allows the user to read actual values
Settings Allows the user to read setting values
Commands Allows the user to execute commands
Event Recorder Allows the user to use the digital fault recorder
FlexLogic Allows the user to read FlexLogic values
Update Info Allows the user to write to any function to which they have read privileges. When any of the Settings, Event
Recorder, and FlexLogic check boxes are enabled by themselves, the user is granted read access. When
any of them are enabled in conjunction with the Update Info box, they are granted read and write access.
The user is not granted write access to functions that are not checked, even if the Update Info field is
checked.
Admin The user is an EnerVista UR Setup administrator, therefore receiving all of the administrative rights.
Exercise caution when granting administrator rights.
4. Click OK to add the user account to the security management system.

MODIFYING USER PRIVILEGES
The following pre-requisites are required to modify user privileges in the EnerVista security management system:
• The user modifying the privileges must have administrator rights
• The EnerVista security management system must be enabled
To modify user privileges:
5 1. Select the Security > User Management menu item to open the user management window.
2. Locate the username in the User field.
3. Modify the user access rights by enabling or disabling one or more of the check boxes.
The table outlines access rights.

FIELD DESCRIPTION
Delete Entry Deletes the user account when exiting the user management window
Actual Values Allows the user to read actual values
Settings Allows the user to read setting values
Commands Allows the user to execute commands


FIELD DESCRIPTION
Event Recorder Allows the user to use the digital fault recorder
FlexLogic Allows the user to read FlexLogic values
Update Info Allows the user to write to any function to which they have read privileges. When any of the Settings, Event
Recorder, and FlexLogic check boxes are enabled by themselves, the user is granted read access. When
any of them are enabled in conjunction with the Update Info box, they are granted read and write access.
The user is not granted write access to functions that are not checked, even if the Update Info field is
checked.
Admin The user is an EnerVista UR Setup administrator, therefore receiving all of the administrative rights.
Exercise caution when granting administrator rights.
4. Click OK to save the changes.
f) CYBERSENTRY SECURITY
The EnerVista software provides the means to configure and authenticate UR using either device or server authentication.
The access to various pieces of functionality depends on user role.
The login screen of EnerVista has two options for access to the UR, server and device authentication.
When the "Device" button is selected, the UR uses its local authentication database and not the RADIUS server to authen-
ticate the user. In this case, it uses built-in roles (Administrator, Engineer, Supervisor, Observer, Operator) as login
accounts and the associated passwords are stored on the UR device. In this case, access is not user-attributable. In cases
where user-attributable access is required, especially for auditable processes for compliance reasons, use server authenti-
cation (RADIUS) only.
When the "Server" Authentication Type option is selected, the UR uses the RADIUS server and not its local authentication
database to authenticate the user.
5
No password or security information is displayed in plain text by the EnerVista software or UR device, nor are they ever
transmitted without cryptographic protection.

CYBERSENTRY SETTINGS THROUGH ENERVISTA

CyberSentry security settings are configured under Device > Settings > Product Setup > Security.
Figure 5–2: CYBERSENTRY SECURITY PANEL

For the Device > Settings > Product Setup > Supervisory option, the panel looks like the following.
Figure 5–3: SUPERVISORY PANEL

For the Security panel, the following settings are available.
RADIUS Server Settings
SETTING NAME DESCRIPTION MIN MAX DEFAULT UNITS MINIMUM
PERMISSION
Primary RADIUS IP IP address of the main RADIUS server. 0.0.0.0 223.255.255.254 0.0.0.0 - Administrator
Address Default value indicates no Primary
RADIUS server is configured, and hence
RADIUS is disabled.
Primary RADIUS authentication port 1 65535 1812 - Administrator
Authentication Port
Primary Accounting RADIUS accounting port 1 65535 1813 - Administrator
Port
Vendor ID An identifier that specifies RADIUS Value that Administrator
vendor-specific attributes used with the represents
protocol General
Electric
RADIUS Shared secret used in authentication. It See the See the following N/A - Administrator
Authentication displays as asterisks. This setting must following password section
(Shared) Secret meet the CyberSentry password password for requirements
requirements. section for
requirements
RADIUS Authentication method used by RADIUS EAP-TTLS EAP-TTLS EAP-TTLS - Administrator
Authentication server. Currently fixed to EAP-TTLS.
Method
Timeout Timeout in seconds between re- 0 9999 10 sec Administrator
transmission requests
Retries Number of retries before giving up 0 9999 3 - Administrator

Confirm RADIUS Confirmation of the shared secret. The See the 245 characters N/A - Administrator
Authentication entry displays as asterisks. following
(Shared) Secret password
section for
requirements
General Security Settings

SETTING NAME DESCRIPTION MIN MAX DEFAULT UNITS MINIMUM
PERMISSION
Session Lockout Number of failed authentications before the 0 (lockout 99 3 - Administrator
device blocks subsequent authentication disabled)
attempts for the lockout period
Session Lockout The period in minutes that a user is prevented 0 (no period) 9999 3 min Administrator
Period from logging in after being locked out
Syslog Server IP The IP address of the target Syslog server to 0.0.0.0 223.255. 0.0.0.0 - Administrator
Address which all security events are transmitted 255.254
Syslog Server Port The UDP port number of the target syslog server 1 65535 514 - Administrator
Number to which all security events are transmitted
Device When enabled, local device authentication with Disabled Enabled Enabled - Administrator
Authentication roles is allowed. When disabled, the UR only
authenticates to the AAA server (RADIUS).
NOTE: Administrator and Supervisor (if still
enabled) remain active even after device
authentication is disabled. The only permission
for local Administrator is to re-enable device
authentication when device authentication is
disabled. To re-enable device authentication, the
Supervisor unlocks the device for setting
changes, and then the Administrator can re-
enable device authentication.
5 Firmware Locked Indicates if the device receives firmware

upgrades. If Yes and the firmware upgrade
No Yes Yes - Administrator
attempt is made, the device denies the upgrade

and displays an error message that the lock is
set. On each firmware upgrade, this setting goes
back to the default.
Factory Service When enabled (checkbox selected), the device Disabled Enabled Disabled - Supervisor
Mode can go into factory service mode. To enable, (Administrator
Supervisor authentication is necessary. when Supervisor
is disabled)
Restore to Defaults Sets the device to factory defaults No Yes No - Administrator
Supervisor role When enabled (checkbox selected), the Disabled Enabled Enabled - Administrator to
Supervisor role is active. To enable, enable and
Administrator authentication is necessary. When Supervisor to
disabled, the Supervisor role is inactive. To disable
disable, Supervisor authentication is necessary.
RADIUS user Ensure that RADIUS user names are not the See RADIUS See - Administrator
names same as local/device role names server RADIUS
documents server
documents
Password Local/device roles except for Observer are See the See the Change Text The specified role
password-protected. All RADIUS users are following following Me1# and Administrator,
password-protected. password password except for
section for section for Supervisor, where
requirements requireme it is only itself
nts

Security Alarm Settings

SETTING NAME DESCRIPTION / DETAILS MIN MAX DEFAULT UNITS MINIMUM
PERMISSIONS
Failed A threshold number indicating when an alarm is 0 99 3 - Administrator
Authentications set off to indicate too many failed authentication (disabled)
attempts
Firmware lock A Boolean value indicating if the device can No Yes Yes - Administrator
receive a firmware upgrade. If Yes and a
firmware upgrade attempt is made, the device
alarm activates. If No the device alarm does not
activate. On each firmware upgrade this setting
goes back to the default.
Settings lock A Boolean value indicating if the device can No Yes Yes - Supervisor
accept any settings changes. If Yes and a (Administrator if
settings change attempt is made, the device Supervisor has
alarm activates. If No, the device alarm does not been disabled)
activate.
CYBERSENTRY SETTINGS THROUGH THE FRONT PANEL

PATH: SETTINGS  PRODUCT SETUP  SECURITY
 SECURITY LOGIN: Range: Administrator, Engineer, Supervisor,

 None Operator, Factory (for factory use only), None
 CHANGE LOCAL
 PASSWORDS
 SESSION
 SETTINGS
MESSAGE
 RESTORE DEFAULTS
See page 5–20.
5

 SUPERVISORY

SYSLOG IP ADDRESS: Range: 0.0.0.0, 255.255.255.255
MESSAGE
0.0.0.0
SYSLOG PORT NUMBER: Range: 1 to 65535
MESSAGE
514
Login: This setting is applicable for Device Authentication only. This setting allows a user to login with a specific role, see
descriptions below. For the Supervisor role, the “Supervisor Role” setting should be enabled.
Whenever a new role is logged in, the user is prompted with a display to enter a password. Passwords must obey the
requirements specified the Password Requirements section in chapter 8.The UR device supports five roles. All roles have
their corresponding passwords. The Observer role is the only role that does not require a password.
The roles are defined as follows:
• Administrator: Complete read and write access to all settings and commands. This role does not allow concurrent
access. This role has an operand to indicate when it is logged on.
• Engineer: Complete read and write access to all settings and commands with the exception of configuring Security set-
tings and Firmware upgrades. This role does not allow concurrent access.
• Operator: The Operator has read/write access to all settings under the command menu/section. This role does not
exist offline.
• Supervisor: This is only an approving role. This role’s authentication commits setting changes submitted by Administra-
tor or Engineer. The Supervisor role authenticates to unlock the UR relay for setting changes and not approve changes
after the fact. Only Supervisor can set the Settings and Firmware Lock in the Security Settings. This role also has the
ability to forcefully logoff any other role and clear the security event log. This role can also be disabled, but only
through a Supervisor authentication. When this role is disabled its permissions are assigned to the Administrator role.

• Observer: This role has read only access to all UR settings. This role allows unlimited concurrent access but it has no
download access to any files on the device. Observer is the default role if no authentication has been done to the
device. This role displays as "None" on the front panel.
The Factory service role is not available and is intended for factory use only.
NOTE
Local Passwords
PATH: SETTINGS  PRODUCT SETUP  SECURITY  CHANGE LOCAL PASSWORDS
 CHANGE LOCAL LOGIN: Range: 20 Alphanumeric Characters

 PASSWORDS None
NEW PASSWORD: Range: 20 Alphanumeric Characters
MESSAGE
CONFIRM PASSWORD: Range: 20 Alphanumeric Characters

MESSAGE
The Change Local Passwords menu is shown on the front panel and Enervista on a successful login of Administrator role.
The “login setting” in this menu is similar to the login setting described in PATH: SETTINGS > PRODUCT SETUP > SECU-
RITY except for the factory role.
Passwords are stored in text format. No encryption is applied.
Notes:
NOTE
5 • In Device Authentication mode, the Observer role does not have a password associated with it. In Server Authentica-
tion mode the Observer role requires a password.
• The default password is “ChangeMe1#”.
• Once the passwords are set, the Administrator with Supervisor approval can change the role associated password.
• In CyberSentry, password encryption is not supported.
Session Settings
PATH: SETTINGS  PRODUCT SETUP  SECURITY  SESSION SETTINGS
 SESSION SESSION LOCKOUT: Range: 0 to 99

 SETTINGS 3
SESSION LOCKOUT Range: 0 to 9999 minutes
MESSAGE
PERIOD: 3 min
The following session settings are available.

• SESSION LOCKOUT: This setting specifies the number of failed authentications (the default is three and the maxi-
mum is 99) before the device blocks subsequent authentication attempts for the lockout period. A value of zero means
lockout is disabled.
• SESSION LOCKOUT PERIOD: This setting specifies the period of time in minutes of a lockout period (the default is
three and the maximum is 9999). A value of 0 means that there is no lockout period.
Restore Defaults
PATH: SETTINGS  PRODUCT SETUP  SECURITY  RESTORE DEFAULTS
 RESTORE DEFAULTS LOAD FACTORY Range: Yes, No

 DEFAULTS: No
• LOAD FACTORY DEFAULTS: This setting is used to reset all the settings, communication and security passwords. An
Administrator role is used to change this setting and a Supervisor role (if not disabled) approves it.

Supervisory
PATH: SETTINGS  PRODUCT SETUP  SECURITY SUPERVISORY
 SUPERVISORY DEVICE Range: Yes, No

 AUTHENTICATION:Yes
BYPASS ACCESS: Range: Local, Remote, Local and Remote, Disabled
MESSAGE
Disabled
LOCK RELAY: Range: Enabled, Disabled
MESSAGE
Disabled
FACTORY SERVICE: Range: Enabled, Disabled
MESSAGE
MODE: Disabled
 SELF TESTS
MESSAGE See below

SUPERVISOR ROLE: Range: Enabled, Disabled
MESSAGE
Disabled
SERIAL INACTIVITY Range: 1 to 9999 minutes
MESSAGE
TIMEOUT: 1 min
The Supervisory menu settings are available for Supervisor role only or if the Supervisor role is disabled then for the
Administrator role only.
Device Authentication: This setting is enabled by default, meaning "Yes" is selected. When enabled, Device Authentica-
tion with roles is enabled. When this setting is disabled, the UR only authenticates to the AAA server (Radius). However,
the Administrator and Supervisor (when enabled) remain active even after device authentication is disabled and their only 5
permission is to re-enable device authentication. To re-enable device authentication, the Supervisor unlocks the device for
setting changes, then the Administrator re-enables device authentication.
Bypass Access: The bypass security feature provides an easier access, with no authentication and encryption for those
special situations when this is considered safe. Only the Supervisor, or the Administrator when the Supervisor role is dis-
abled, can enable this feature.
MODE FRONT PANEL OR SERIAL (RS232, RS485) ETHERNET
Normal mode Authentication — Role Based Access Control (RBAC) Authentication — RBAC and passwords encrypted
and passwords in clear SSH tunneling
Bypass access mode No passwords for allowed RBAC levels No passwords for allowed RBAC levels
No SSH tunneling
The bypass options are as follows:

• Local — Bypasses authentication for push buttons, keypad, RS232, and RS485
• Remote — Bypasses authentication for Ethernet
• Local and Remote — Bypasses authentication for push buttons, keypad, RS232, RS485, and Ethernet
Lock Relay: This setting uses a Boolean value (Enable/Disable) to indicate if the device accepts setting changes and
whether the device can receive a firmware upgrade. This setting can be changed only by the Supervisor role, if it is enabled
or by the Administrator if the Supervisor role is disabled. The Supervisor role enables this setting for the relay to start
accepting setting changes or command changes or firmware upgrade. After all the setting changes are applied or com-
mands executed, the Supervisor disables to lock setting changes.
Example: If this setting is "Yes" and an attempt is made to change settings or upgrade the firmware, the UR device denies
the setting changes and denies upgrading the firmware. If this setting is "No", the UR device accepts setting changes and
firmware upgrade.
This role is disabled by default.
Factory Service Mode: When enabled (i.e., "Yes" is selected) the device can go into factory service mode. For this set-
ting to become enabled a Supervisor authentication is necessary. The default value is Disabled.

Supervisor Role: When enabled (i.e., "Yes" is selected) the Supervisor role is active. When "No" is selected this role is dis-
abled. To disabled this setting a Supervisor authentication is necessary. If disabled, the Supervisor role is not allowed to log
on. In this case the Administrator can change the settings under the Supervisory menu.
If enabled, Supervisor authentication is required to change the settings in the Supervisory menu. If the Supervisor disables
his role after authentication, the Supervisor session remains valid until he switches to another role using MMI or until he
ends the current Supervisor session if using communications.
This role is disabled by default.
Serial Inactivity Timeout: The role logged via a serial port is auto logged off after the Serial Inactivity timer times out. A
separate timer is maintained for RS232 and RS485 connections. The default value is 1 minute.
a) SELF TESTS
PATH: SETTINGS  PRODUCT SETUP  SECURITY SUPERVISORY SELF TESTS
 SELF TESTS  FAILED

See below
  AUTHENTICATE
FIRMWARE LOCK: Range: Enabled, Disabled
MESSAGE
Enabled
SETTINGS LOCK: Range: Enabled, Disabled
MESSAGE
Enabled
Failed Authentications: If this setting is Enabled then the number of failed authentications is compared with the Session
lockout threshold. When the Session lockout threshold is exceeded, this minor alarm indication comes up.
Firmware Lock: If this setting is Enabled then any firmware upgrade operation attempt when the “LOCK FIRMWARE
5 UPGRADE” setting is set to “Yes” brings up this self test alarm.
Settings Lock: If this setting is Enabled then an unauthorized write attempt to a setting for a given role activates this self
test.
PATH: SETTINGS  PRODUCT SETUP  SECURITY SUPERVISORY SELF TESTS FAILED AUTHENTICATE
 FAILED FAILED AUTHENTICATE: Range: Enabled, Disabled

 AUTHENTICATE Enabled
CYBERSENTRY SETUP
When first using CyberSentry security, use the following procedure for set up.
1. Log in to the relay as Administrator by using the Value keys on the front panel to enter the default password
"ChangeMe1#". Note that the "Lock relay" setting needs to be disabled in the Security > Supervisory menu. When
this setting is disabled, configuration and firmware upgrade are possible. By default, this setting is disabled.
2. Enable the Supervisor role if you have a need for it.
3. Make any required changes in configuration, such as setting a valid IP address for communication over Ethernet.
4. Log out of the Administrator account by choosing None.
Next, device or server authentication can be chosen on the login screen, but the choice is available only in EnerVista. Use
device authentication to log in using the five pre-configured roles (Administrator, Supervisor, Engineer, Operator,
Observer). When using a serial connection, only device authentication is supported. When server authentication is
required, characteristics for communication with a RADIUS server must be configured. This is possible only in the EnerV-
ista software. The RADIUS server itself also must be configured. The appendix called RADIUS Server gives an example of
how to setup a simple RADIUS server. Once both the RADIUS server and the parameters for connecting UR to the server
have been configured, you can choose server authentication on the login screen of EnerVista.
The use of CyberSentry for devices communicating through an Ethernet-to-RS485 gateway is not
supported. Because these gateways do not support the secure protocols necessary to communicate
with such devices, the connection cannot be established. Use the device as a non-CyberSentry
device.

Users logged in through the front panel are not timed out and cannot be forcefully logged out by a
supervisor. Roles logged in through the front panel that do no allow multiple instances (Administrator,
Supervisor, Engineer, Operator) must switch to None (equivalent to a logout) when they are done in
order to log out.
For all user roles except Observer, only one instance can be logged in at one time, for both login by
front panel and software.
To configure server authentication:

1. In the EnerVista software, choose device authentication and log in as Administrator.
2. Configure the following RADIUS server parameters: IP address, authentication port, shared secret, and vendor ID.
3. On the RADIUS server, configure the user accounts. Do not use the five pre-defined roles as user names (Administra-
tor, Supervisor, Engineer, Operator, Observer) in the RADIUS server. If you do, the UR relay automatically provides the
authentication from the device.
4. In the EnerVista software, choose server authentication and log in using the user name and password configured on
the RADIUS server for server authentication login.
5. After making any required changes, log out.
When changing settings offline, ensure that only settings permitted by the role that performs the set-
tings download are changed because only those changes are applied.
Pushbuttons (both user-control buttons and user-programmable buttons) located on the front panel can be pressed by an
Administrator or Engineer role. This also applies to the reset button, which resets targets, where targets are errors dis-
played on the front panel or the Targets panel of the EnerVista software. The reset button has special behavior in that it
allows these two roles to press it even when they are logged in through the RS232 port and not through the front panel. 5
To reset the security event log and self-test operands:
1. Log in as Supervisor (if the role is enabled) or Administrator (if the Supervisor role is disabled) and execute a clear
security command under Commands > Security > Clear Security.
5.2.2 DISPLAY PROPERTIES
PATH: SETTINGS  PRODUCT SETUP  DISPLAY PROPERTIES
 DISPLAY LANGUAGE: Range: English; English, French; English, Russian;

 PROPERTIES English English, Chinese
(range dependent on order code)
FLASH MESSAGE Range: 0.5 to 10.0 s in steps of 0.1
MESSAGE
TIME: 1.0 s
DEFAULT MESSAGE Range: 10 to 900 s in steps of 1
MESSAGE
TIMEOUT: 300 s
DEFAULT MESSAGE Range: 25%, 50%, 75%, 100%
MESSAGE Visible only if a VFD is installed
INTENSITY: 25 %
SCREEN SAVER Range: Disabled, Enabled
MESSAGE Visible only if an LCD is installed
FEATURE: Disabled
SCREEN SAVER WAIT Range: 1 to 65535 min. in steps of 1
MESSAGE Visible only if an LCD is installed
TIME: 30 min
CURRENT CUT-OFF Range: 0.002 to 0.020 pu in steps of 0.001
MESSAGE
LEVEL: 0.020 pu
VOLTAGE CUT-OFF Range: 0.1 to 1.0 V secondary in steps of 0.1
MESSAGE
LEVEL: 1.0 V
Some relay messaging characteristics can be modified to suit different situations using the display properties settings.

• LANGUAGE: This setting selects the language used to display settings, actual values, and targets. The range is
dependent on the order code of the relay.
• FLASH MESSAGE TIME: Flash messages are status, warning, error, or information messages displayed for several
seconds in response to certain key presses during setting programming. These messages override any normal mes-
sages. The duration of a flash message on the display can be changed to accommodate different reading rates.
• DEFAULT MESSAGE TIMEOUT: If the keypad is inactive for a period of time, the relay automatically reverts to a
default message. The inactivity time is modified via this setting to ensure messages remain on the screen long enough
during programming or reading of actual values.
• DEFAULT MESSAGE INTENSITY: To extend phosphor life in the vacuum fluorescent display, the brightness can be
attenuated during default message display. During keypad interrogation, the display always operates at full brightness.
• SCREEN SAVER FEATURE and SCREEN SAVER WAIT TIME: These settings are only visible if the D60 has a liquid
crystal display (LCD) and control its backlighting. When the SCREEN SAVER FEATURE is “Enabled”, the LCD backlighting
is turned off after the DEFAULT MESSAGE TIMEOUT followed by the SCREEN SAVER WAIT TIME, providing that no keys
have been pressed and no target messages are active. When a keypress occurs or a target becomes active, the LCD
backlighting is turned on.
• CURRENT CUT-OFF LEVEL: This setting modifies the current cut-off threshold. Very low currents (1 to 2% of the
rated value) are very susceptible to noise. Some customers prefer very low currents to display as zero, while others
prefer the current be displayed even when the value reflects noise rather than the actual signal. The D60 applies a cut-
off value to the magnitudes and angles of the measured currents. If the magnitude is below the cut-off level, it is substi-
tuted with zero. This applies to phase and ground current phasors as well as true RMS values and symmetrical compo-
nents. The cut-off operation applies to quantities used for metering, protection, and control, as well as those used by
communications protocols. Note that the cut-off level for the sensitive ground input is 10 times lower that the CURRENT
CUT-OFF LEVEL setting value. Raw current samples available via oscillography are not subject to cut-off.
5 • VOLTAGE CUT-OFF LEVEL: This setting modifies the voltage cut-off threshold. Very low secondary voltage measure-
ments (at the fractional volt level) can be affected by noise. Some customers prefer these low voltages to be displayed
as zero, while others prefer the voltage to be displayed even when the value reflects noise rather than the actual sig-
nal. The D60 applies a cut-off value to the magnitudes and angles of the measured voltages. If the magnitude is below
the cut-off level, it is substituted with zero. This operation applies to phase and auxiliary voltages, and symmetrical
components. The cut-off operation applies to quantities used for metering, protection, and control, as well as those
used by communications protocols. Raw samples of the voltages available via oscillography are not subject cut-off.
The CURRENT CUT-OFF LEVEL and the VOLTAGE CUT-OFF LEVEL are used to determine the metered power cut-off levels. The
power cut-off level is calculated as shown below. For Delta connections:
3  CURRENT CUT-OFF LEVEL  VOLTAGE CUT-OFF LEVEL  VT primary  CT primary

3-phase power cut-off = ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------ (EQ 5.3)
VT secondary
For Wye connections:
3  CURRENT CUT-OFF LEVEL  VOLTAGE CUT-OFF LEVEL  VT primary  CT primary
3-phase power cut-off = -------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- (EQ 5.4)
VT secondary
CURRENT CUT-OFF LEVEL  VOLTAGE CUT-OFF LEVEL  VT primary  CT primary
per-phase power cut-off = ---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- (EQ 5.5)
VT secondary
where VT primary = VT secondary  VT ratio and CT primary = CT secondary  CT ratio.
For example, given the following settings:
CURRENT CUT-OFF LEVEL: “0.02 pu”
VOLTAGE CUT-OFF LEVEL: “1.0 V”
PHASE CT PRIMARY: “100 A”
PHASE VT SECONDARY: “66.4 V”
PHASE VT RATIO: “208.00 : 1"
PHASE VT CONNECTION: “Delta”.
We have:
CT primary = “100 A”, and
VT primary = PHASE VT SECONDARY x PHASE VT RATIO = 66.4 V x 208 = 13811.2 V

The power cut-off is therefore:

power cut-off = (CURRENT CUT-OFF LEVEL  VOLTAGE CUT-OFF LEVEL  CT primary  VT primary)/VT secondary
= ( 3  0.02 pu  1.0 V  100 A  13811.2 V) / 66.4 V
= 720.5 watts
Any calculated power value below this cut-off will not be displayed. As well, the three-phase energy data will not accumu-
late if the total power from all three phases does not exceed the power cut-off.
Lower the VOLTAGE CUT-OFF LEVEL and CURRENT CUT-OFF LEVEL with care as the relay accepts lower sig-
nals as valid measurements. Unless dictated otherwise by a specific application, the default settings of “0.02 pu” for
NOTE
CURRENT CUT-OFF LEVEL and “1.0 V” for VOLTAGE CUT-OFF LEVEL are recommended.
5.2.3 CLEAR RELAY RECORDS
PATH: SETTINGS  PRODUCT SETUP  CLEAR RELAY RECORDS
 CLEAR RELAY CLEAR FAULT REPORTS: Range: FlexLogic operand

 RECORDS Off
CLEAR EVENT RECORDS: Range: FlexLogic operand
MESSAGE
Off
CLEAR OSCILLOGRAPHY? Range: FlexLogic operand
MESSAGE
No
CLEAR DATA LOGGER: Range: FlexLogic operand
MESSAGE
Off
MESSAGE
CLEAR ARC AMPS 1:
Off
Range: FlexLogic operand
5
CLEAR ARC AMPS 2: Range: FlexLogic operand
MESSAGE
Off
CLEAR ENERGY: Range: FlexLogic operand
MESSAGE
Off
RESET UNAUTH ACCESS: Range: FlexLogic operand
MESSAGE
Off
CLEAR DIR I/O STATS: Range: FlexLogic operand.
MESSAGE Valid only for units with Direct I/O module.
Off
Selected records can be cleared from user-programmable conditions with FlexLogic operands. Assigning user-programma-
ble pushbuttons to clear specific records are typical applications for these commands. Since the D60 responds to rising
edges of the configured FlexLogic operands, they must be asserted for at least 50 ms to take effect.
Clearing records with user-programmable operands is not protected by the command password. However, user-program-
mable pushbuttons are protected by the command password. Thus, if they are used to clear records, the user-programma-
ble pushbuttons can provide extra security if required.
For example, to assign user-programmable pushbutton 1 to clear demand records, the following settings should be applied.
1. Assign the clear demand function to pushbutton 1 by making the following change in the SETTINGS  PRODUCT SETUP
 CLEAR RELAY RECORDS menu:
CLEAR DEMAND: “PUSHBUTTON 1 ON”
2. Set the properties for user-programmable pushbutton 1 by making the following changes in the SETTINGS  PRODUCT
SETUP  USER-PROGRAMMABLE PUSHBUTTONS  USER PUSHBUTTON 1 menu:
PUSHBUTTON 1 FUNCTION: “Self-reset”
PUSHBTN 1 DROP-OUT TIME: “0.20 s”

a) MAIN MENU
PATH: SETTINGS  PRODUCT SETUP  COMMUNICATIONS
 COMMUNICATIONS  SERIAL PORTS

See below.
 
 NETWORK

 ROUTING

 MODBUS PROTOCOL

 DNP PROTOCOL

 DNP / IEC104
 POINT LISTS
 IEC 61850 PROTOCOL

 WEB SERVER
 HTTP PROTOCOL
5 MESSAGE
 TFTP PROTOCOL

See page 5–53.
 IEC 60870-5-104
 PROTOCOL
b) SERIAL PORTS
PATH: SETTINGS  PRODUCT SETUP  COMMUNICATIONS  SERIAL PORTS
 SERIAL PORTS RS485 COM2 BAUD Range: 300, 1200, 2400, 4800, 9600, 14400, 19200,
 RATE: 19200 28800, 33600, 38400, 57600, 115200
RS485 COM2 PARITY: Range: None, Odd, Even

MESSAGE
None
RS485 COM2 RESPONSE Range: 0 to 1000 ms in steps of 10
MESSAGE
MIN TIME: 0 ms
The D60 is equipped with up to two independent serial communication ports. The faceplate RS232 port is intended for local
use and is fixed at 19200 baud and no parity. The rear COM2 port is RS485. The RS485 port has settings for baud rate and
parity. It is important that these parameters agree with the settings used on the computer or other equipment that is con-
nected to these ports. Any of these ports can be connected to a computer running EnerVista UR Setup. This software can
download and upload setting files, view measured parameters, and upgrade the relay firmware. A maximum of 32 relays
can be daisy-chained and connected to a DCS, PLC, or computer using the RS485 ports.
For the RS485 port, the minimum time before the port transmits after receiving data from a host can be set. This
feature allows operation with hosts which hold the RS485 transmitter active for some time after each transmission.
NOTE
c) ETHERNET NETWORK TOPOLOGY

When using more than one Ethernet port, configure each to belong to a different network or subnet using the IP addresses
and mask, else communication becomes unpredictable when more than one port is configured to the same subnet.

Example 1
IP1/Mask1: 10.1.1.2/255.255.255.0 (where LAN 1 is 10.1.1.x/255.255.255.0)
IP2/Mask2: 10.2.1.2/255.255.255.0 (where LAN2 is 10.2.1.x/255.255.255.0)
IP3/Mask3: 10.3.1.2/255.255.255.0 (where LAN3 is 10.3.1.x/255.255.255.0)
Example 2
IP1/Mask1: 10.1.1.2/255.0.0.0 (where LAN1 is 10.x.x.x/255.0.0.0)
Example 3 — Incorrect
IP1/Mask1: 10.1.1.2/255.0.0.0
IP2/Mask2: 10.2.1.2/255.0.0.0
IP3/Mask3: 10.3.1.2/255.0.0.0
This example is incorrect because the mask of 255.0.0.0 used for the three IP addresses makes them belong to the same
network of 10.x.x.x.
Single LAN, No Redundancy
The topology shown in the following figure allows communications to SCADA, local configuration/monitoring through
EnerVista, and access to the public network shared on the same LAN. No redundancy is provided.
Figure 5–4: NETWORK CONFIGURATION FOR SINGLE LAN

Multiple LANS, with Redundancy

The topology in the following figure provides local configuration/monitoring through EnerVista software and access to the
public network shared on LAN1, to which port 1 (P1) is connected. There is no redundancy provided on LAN1. Communica-
tions to SCADA is provided through LAN2 and LAN3, to which P2 and respectively P3 are connected and configured to
work in redundant mode. In this configuration, P3 uses the IP and MAC address of P2.
Figure 5–5: MULTIPLE LANS, WITH REDUNDANCY
Multiple LANS, No Redundancy

The following topology provides local configuration/monitoring through EnerVista software on LAN1, to which port 1 (P1) is
connected, access to the public network on LAN2, to which port 2 (P2) is connected and communications with SCADA on
LAN3, to which port 3 (P3) is connected. There is no redundancy.
Figure 5–6: MULTIPLE LANS, NO REDUNDANCY

d) NETWORK
As outlined in the previous section, when using more than one Ethernet port, configure each to belong to a different net-
work or subnet using the IP addresses and mask. Configure the network IP and subnet settings before configuring the rout-
ing settings.
PATH: SETTINGS  PRODUCT SETUP  COMMUNICATIONS  NETWORK 1(3)
 NETWORK PORT 1 PRT1 IP ADDRESS: Range: Standard IPV4 address format

 127.0.0.1
PRT1 SUBNET IP MASK: Range: Standard IPV4 address format
MESSAGE
255.0.0.0
PRT1 GOOSE ENABLED: Range: Enabled, Disabled
MESSAGE
Enabled

 127.0.0.1
MESSAGE
255.0.0.0
PRT2 REDUNDANCY: Range: None, Failover, PRP

MESSAGE None, Failover (if no PRP license)
None
PRT2 PRP MCST ADDR: Range: 01-15-4E-00-01-00 to 01-15-4E-00-01-FF
5
MESSAGE
01-15-4E-00-01-00
MESSAGE
Enabled

 127.0.0.1
MESSAGE
255.0.0.0
MESSAGE
Enabled
The IP addresses are used with the DNP, Modbus/TCP, IEC 61580, IEC 60870-5-104, TFTP, HTTP, and PRP protocols.
The next section explains PRP.
Do not set more than one protocol to the same TCP/UDP port number, as this results in unreliable operation of
those protocols.
NOTE
PRT1 (2 OR 3) IP ADDRESS: This setting sets the ports IPv4 address in standard IPV4 format. This setting is valid on port 3 if
port 2 REDUNDANCY is set to None.
PRT1 (2 OR 3) SUBNET MASK: This setting sets the ports IPv4 subnet mask in standard IPV4 format. This setting is valid on
port 3 if port 2 REDUNDANCY is set to None.
PRT2 REDUNDANCY is available when the hardware has multiple ports (modules T, U, and V). It determines if ports 2 and 3
operate in redundant or independent mode. If a license for PRP was purchased, the options are None, Failover, and PRP.
If a license for PRP was not purchased, the available options are None and Failover. In non-redundant mode (REDUNDANCY
set to None), ports 2 and 3 operate independently with their own MAC, IP, and mask addresses. If REDUNDANCY is set to
Failover, the operation of ports 2 and 3 is as follows:
• Ports 2 and 3 use the port 2 MAC address, IP address, and mask
• The configuration fields for IP address and mask on port 3 are hidden

• Port 3 is in standby mode and does not actively communicate on the Ethernet network but monitors its link to the Mul-
tilink switch. If port 2 detects a problem with the link, communications is switched to Port 3. Port 3 is, in effect, acting as
a redundant or backup link to the network for port 2. Once Port 2 detects that the link between port 2 and the switch is
good, communications automatically switch back to port 2 and port 3 goes back into standby mode.
If REDUNDANCY is set to PRP, the operation of ports 2 and 3 is as follows:
• Ports 2 and 3 use the port 2 MAC address, IP address, and mask
• The configuration fields for IP address and mask on port 3 are overwritten with those from port 2. This is visible on the
front panel but not displayed in the EnerVista software.
• Port 2 MCST ADDRESS field is visible
• The port 2 PTP function still uses only port 2 and the port 3 PTP function still uses only port 3. The relay still synchro-
nizes to whichever port has the best master. When ports 2 and 3 see the same master, as is typically the case for PRP
networks, the port with the better connectivity is used.
The two ports must be connected to completely independent LANS with no single point of failure, such as common
power supplies that feed switches on both LANS.
NOTE
For this setting change to take effect, restart the unit.

PRT2 PRP MCST ADDR: This setting allows the user to change the multicast address used by the PRP supervision frames.
The setting applies to UR CPUs that support multiple ports (T, U, and V). This setting is available if the hardware has multi-
ple ports and REDUNDANCY is set to PRP.
e) PARALLEL REDUNDANCY PROTOCOL (PRP)
5 The Parallel Redundancy Protocol (PRP) defines a redundancy protocol for high availability in substation automation net-
works. It applies to networks based on Ethernet technology (ISO/IEC 8802-3) and is based on the second edition (July
2012) of the IEC 62439-3, clause 4.
PRP is designed to provide seamless recovery in case of a single failure in the network, by using a combination of LAN
duplication and frame duplication technique. Identical frames are sent on two completely independent networks that con-
nect source and destination. Under normal circumstances both frames reach the destination and one of them is sent up the
OSI stack to the destination application, while the second one is discarded. If an error occurs in one of the networks and
traffic is prevented from flowing on that path, connectivity is still provided through the other network to ensure continuous
communication. Take care when designing the two LANs, so that no single point of failure (such as a common power sup-
ply) is encountered, as such scenarios can bring down both LANs simultaneously.
Figure 5–7: EXAMPLE OF PARALLEL REDUNDANT NETWORK
PRP uses specialized nodes called doubly attached nodes (DANPs) for handling the duplicated frames. DANPs devices
have an additional module, called Link Redundancy Entity (LRE). LRE is responsible for duplicating frames and adding the
specific PRP trailer when sending the frames out on the LAN, as well as making decisions on received frames as to which
one is sent up the OSI stack to the application layer and which one is discarded. LRE is responsible for making PRP trans-
parent to the higher layers of the stack. There is a second type of specialized device used in PRP networks, called RedBox,
with the role of connecting Single Attached Nodes (SANs) to a redundant network.
UR relays implement only the DANP functionality. The RedBox functionality is not implemented.

The original standard IEC 62439-3 (2010) was amended to align PRP with the High-availability Seamless Redundancy
(HSR) protocol. To achieve this, the original PRP was modified at the cost of losing compatibility with the PRP 2010 ver-
sion. The revised standard IEC 62439-3 (2012) is commonly referred to as PRP-1, while the original standard is PRP-0.
The UR relays support only PRP-1.
The relay implements PRP on two of its Ethernet ports, specifically Port 2 and 3 of the CPU module. Use the previous sec-
tion (network port configuration) to configure PRP.
PRP is purchased as a separate option. If purchased (valid order code), PRP can be enabled in configuration through a
setting available on the network configuration menu, REDUNDANCY, which already has the capability of enabling failover
redundancy. The options on this setting must be changed to accommodate two types of redundancy: failover and PRP.
When REDUNDANCY is set to either failover or PRP, the ports dedicated for PRP (Port 2 and 3) operate in redundant
mode. In this mode, Port 3 uses the Mac, IP address, and mask of Port 2.
f) ROUTING
PATH: SETTINGS  PRODUCT SETUP  COMMUNICATIONS  ROUTING 1(6)
 IPV4 ROUTING IPV4 DEFAULT ROUTE

 TABLE
IPV4 STATIC
MESSAGE
NETWORK ROUTE 1

IPV4 STATIC
MESSAGE
NETWORK ROUTE 6
A default route and a maximum number of six static routes can be configured. 5
The default route is used as the last choice when no other route towards a given destination is found.
 IPV4 DEFAULT ROUTE GATEWAY ADDRESS Range: Standard IPV4 unicast address format
 127.0.0.1
 IPV4 STATIC RT1 DESTINATION: Range: Standard IPV4 address format

 NETWORK ROUTE 1 127.0.0.1
RT1 NET MASK: Range: Standard IPV4 subnet mask format
MESSAGE
255.0.0.0
RT1 GATEWAY: Range: Standard IPV4 unicast address format
MESSAGE
127.0.0.1
Configure the network IP and subnet settings before configuring the routing settings.
ADDING AND DELETING STATIC ROUTES
Host routes are not supported at present.
The routing table configuration is available on the serial port and front panel. This is a deliberate decision, to avoid loss of
connectivity when remotely configuring the UR.
By default the value of the destination field is 127.0.0.1 for all static routes (1 to 6). This is equivalent to saying that the
static routes are not configured. When the destination address is 127.0.0.1, the mask and gateway must be also kept on
default values.
By default, the value of the route gateway address is 127.0.0.1. This means the default route is not configured.
To add a route:
1. Use any of the static network route entries numbered 1 to 6 to configure a static network route. Once a route destina-
tion is configured for any of the entries 1 to 6, that entry becomes a static route and it must meet all the rules listed in
the next section, General Conditions to be Satisfied by Static Routes.

2. To configure the default route, enter a default gateway address. Once a default gateway address is configured, it must
be validated against condition 2 of the General Conditions to be Satisfied by Static Routes.
To delete a route:
1. Replace the route destination with the default loopback address (127.0.0.1). When deleting a route, the mask and
gateway must be also brought back to default values.
2. Delete the default route by replacing the default gateway with the default value 127.0.0.1.
GENERAL CONDITIONS TO BE SATISFIED BY STATIC ROUTES
The following rules are validated internally:
• The route mask has IP mask format. In binary this needs to be a set of contiguous bits of 1 from left to right, followed
by one or more contiguous bits of 0.
• The route destination and mask must match. This can be verified by checking that
RtDestination and RtMask = RtDestination
Example of good configuration: RtDestination = 10.1.1.0; Rt Mask = 255.255.255.0
Example of bad configuration: RtDestination = 10.1.1.1; Rt Mask = 255.255.255.0
The following rules must be observed when you configure static routes:
• The route destination must not be a connected network
• The route gateway must be on a connected network. This rule applies to the gateway address of the default route as
well. This can be verified by checking that:
RtGwy and Prt1Mask = Prt1IP and Prt1Mask || RtGwy and Prt2Mask = Prt2IP and Prt2Mask || RtGwy and Prt3Mask =
Prt3IP and Prt3Mask
ROUTING BEHAVIOR COMPARED TO PREVIOUS RELEASES
5 Prior to release 7.10, the UR did not have an explicit manner of configuring routes. The only available route was the default
route configured as part of the network settings (port gateway IP address). This limited the ability to route to specific desti-
nations, particularly if these destinations were reachable through a different interface than the one on which the default
gateway was.
Starting with UR 7.10, up to six static network routes can be configured in addition to a default route. The default route con-
figuration was also moved from the network settings into the routing section.
The figure shows an example of topology that benefits from the addition of static routes.
Figure 5–8: USING STATIC ROUTES
In the figure, the UR connects through the following two Ethernet ports:
• Port 1 (IP address 10.1.1.2) connects the UR to LAN 10.1.1.0/24 and to the Internet through Router1. Router 1 has an
interface on 10.1.1.0/24 and the IP address of this interface is 10.1.1.1.

• Port 2 (IP address 10.1.2.2) connects the UR to LAN 10.1.2.0/24 and to the EnerVista software through Router 2.
Router 2 has an interface on 10.1.2.0/24 and the IP address of this interface is 10.1.2.1.
The configuration before release 7.10 was as follows:
• PRT1 IP ADDRESS = 10.1.1.2
PRT1 SUBNET IP MASK = 255.255.255.0
PRT1 GWY IP ADDRESS = 10.1.1.1
PRT2 IP ADDRESS = 10.1.2.2
The behavior before release 7.10 was as follows. When sending packets to EnerVista, the UR noticed that the destination
was not on a connected network and it tried to find a route to destination. Since the default route was the only route it knew,
it used it. Yet EnerVista was on a private network, which was not reachable through Router 1. Hence a destination unreach-
able message was received from the router.
The configuration starting release 7.10 is as follows:
• PRT1 IP ADDRESS = 10.1.1.2
PRT2 IP ADDRESS = 10.1.2.2
IPV4 DEFAULT ROUTE: GATEWAY ADDRESS = 10.1.1.1
STATIC NETWORK ROUTE 1: RT1 DESTINATION = 10.1.3.0/24; RT1 NET MASK = 255.255.255.0; and RT1 GATE-
WAY = 10.1.2.1
The behavior since release 7.10 is as follows. There is one added static network route to the destination 10.1.3.0/24, where
a laptop running EnerVista is located. This static route uses a different gateway (10.1.2.1) than the default route. This gate-
way is the address of Router 2, which has knowledge about 10.1.3.0 and is able to route packets coming from UR and des-
tined to EnerVista. 5
SHOW ROUTES AND ARP TABLES
This feature is available on the Web interface, where the main menu contains an additional Communications menu and two
submenus:
• Routing Table
• ARP Table
The tables outline the information displayed when the two submenus are selected.
Table 5–3: ROUTING TABLE INFORMATION
FIELD DESCRIPTION
Destination The IP address of the remote network to which this route points
Mask The network mask for the destination
Gateway The IP address of the next router to the remote network
Interface Interface through which the specified network can be reached
Table 5–4: IP ARP INFORMATION

FIELD DESCRIPTION
IP Address The network address that corresponds to Hardware Address
Age (min) Age, in minutes, of the cache entry. A hyphen (-) means the address is local.
Hardware Address LAN hardware address, a MAC address that corresponds to network address
Type Dynamic or Static
Interface Interface to which this address mapping has been assigned

g) MODBUS PROTOCOL
PATH: SETTINGS  PRODUCT SETUP  COMMUNICATIONS  MODBUS PROTOCOL
 MODBUS PROTOCOL MODBUS SLAVE Range: 0 to 254 in steps of 1

 ADDRESS: 254
MODBUS TCP PORT Range: 0 to 65535 in steps of 1
MESSAGE
NUMBER: 502
The serial communication ports utilize the Modbus protocol, unless configured for DNP operation (see descriptions below).
This allows the EnerVista UR Setup software to be used. The UR operates as a Modbus slave device only. When using
Modbus protocol on the RS232 port, the D60 responds regardless of the MODBUS SLAVE ADDRESS programmed. For the
RS485 port, each D60 must have a unique address from 1 to 254. Address 0 is the broadcast address which all Modbus
slave devices listen to. Addresses do not have to be sequential, but no two devices can have the same address or conflicts
resulting in errors will occur. Generally, each device added to the link should use the next higher address starting at 1. See
Appendix B for more information on the Modbus protocol.
A value of 0 closes the port. When the Modbus port is set to 0, communicate with the relay using the front panel or serial
port.
When a 0 value is involved in a change, the changes to the MODBUS TCP PORT NUMBER setting take effect
when the D60 is restarted.
NOTE
h) DNP PROTOCOL
PATH: SETTINGS  PRODUCT SETUP  COMMUNICATIONS  DNP PROTOCOL
5  DNP PROTOCOL

 DNP CHANNELS

Range: see sub-menu below
DNP ADDRESS: Range: 0 to 65519 in steps of 1

MESSAGE
1
 DNP NETWORK Range: see sub-menu below
MESSAGE
 CLIENT ADDRESSES
DNP TCP/UDP PORT Range: 0 to 65535 in steps of 1
MESSAGE
NUMBER: 20000
DNP UNSOL RESPONSE Range: Enabled, Disabled
MESSAGE
FUNCTION: Disabled
DNP UNSOL RESPONSE Range: 0 to 60 s in steps of 1
MESSAGE
TIMEOUT: 5 s
DNP UNSOL RESPONSE Range: 1 to 255 in steps of 1
MESSAGE
MAX RETRIES: 10
DNP UNSOL RESPONSE Range: 0 to 65519 in steps of 1
MESSAGE
DEST ADDRESS: 1
DNP CURRENT SCALE Range: 0.001, 0.01. 0.1, 1, 10, 100, 1000, 10000,
MESSAGE 100000
FACTOR: 1
DNP VOLTAGE SCALE Range: 0.001, 0.01. 0.1, 1, 10, 100, 1000, 10000,
MESSAGE 100000
FACTOR: 1
DNP POWER SCALE Range: 0.001, 0.01. 0.1, 1, 10, 100, 1000, 10000,
MESSAGE 100000
FACTOR: 1
DNP ENERGY SCALE Range: 0.001, 0.01. 0.1, 1, 10, 100, 1000, 10000,
MESSAGE 100000
FACTOR: 1
DNP PF SCALE Range: 0.001, 0.01. 0.1, 1, 10, 100, 1000, 10000,
MESSAGE 100000
FACTOR: 1

DNP OTHER SCALE Range: 0.001, 0.01. 0.1, 1, 10, 100, 1000, 10000,
MESSAGE 100000
FACTOR: 1
DNP CURRENT DEFAULT Range: 0 to 100000000 in steps of 1
MESSAGE
DEADBAND: 30000
DNP VOLTAGE DEFAULT Range: 0 to 100000000 in steps of 1
MESSAGE
DEADBAND: 30000
DNP POWER DEFAULT Range: 0 to 100000000 in steps of 1
MESSAGE
DEADBAND: 30000
DNP ENERGY DEFAULT Range: 0 to 100000000 in steps of 1
MESSAGE
DEADBAND: 30000
DNP PF DEFAULT Range: 0 to 100000000 in steps of 1
MESSAGE
DEADBAND: 30000
DNP OTHER DEFAULT Range: 0 to 100000000 in steps of 1
MESSAGE
DEADBAND: 30000
DNP TIME SYNC IIN Range: 1 to 10080 min. in steps of 1
MESSAGE
PERIOD: 1440 min
DNP MESSAGE FRAGMENT Range: 30 to 2048 in steps of 1
MESSAGE
SIZE: 240
DNP OBJECT 1 Range: 1, 2
MESSAGE
DEFAULT VARIATION: 2
DNP OBJECT 2 Range: 1, 2, 3
5
MESSAGE
DNP OBJECT 20 Range: 1, 2, 5, 6
MESSAGE
MESSAGE
MESSAGE
MESSAGE
DNP OBJECT 30 Range: 1, 2, 3, 4, 5
MESSAGE
DNP OBJECT 32 Range: 1, 2, 3, 4, 5, 7
MESSAGE
DNP NUMBER OF PAIRED Range: 0 to 32 in steps of 1
MESSAGE
CONTROL POINTS: 0
DNP TCP CONNECTION Range: 10 to 7200 s in steps of 1
MESSAGE
TIMEOUT: 120 s
The D60 supports the Distributed Network Protocol (DNP) version 3.0. The D60 can be used as a DNP slave device con-
nected to multiple DNP masters (usually an RTU or a SCADA master station). Since the D60 maintains two sets of DNP
data change buffers and connection information, two DNP masters can actively communicate with the D60 at one time.
The IEC 60870-5-104 and DNP protocols cannot be used simultaneously. When the IEC 60870-5-104 FUNCTION
setting is set to “Enabled”, the DNP protocol is not operational. When this setting is changed it does not become
NOTE
active until power to the relay has been cycled (off-to-on).
The DNP Channels sub-menu is shown below.

PATH: SETTINGS  PRODUCT SETUP  COMMUNICATIONS  DNP PROTOCOL  DNP CHANNELS
 DNP CHANNELS DNP CHANNEL 1 PORT: Range: NONE, COM2 - RS485,

 NETWORK FRONT PANEL - RS232, NETWORK - TCP,
NETWORK - UDP
DNP CHANNEL 2 PORT: Range: NONE, COM2 - RS485,
MESSAGE FRONT PANEL - RS232, NETWORK - TCP,
COM2 - RS485
NETWORK - UDP
The DNP CHANNEL 1 PORT and DNP CHANNEL 2 PORT settings select the communications port assigned to the DNP protocol
for each channel. Once DNP is assigned to a serial port, the Modbus protocol is disabled on that port. When this setting is
set to “Network - TCP”, the DNP protocol can be used over TCP/IP on channels 1 or 2. When this value is set to “Network -
UDP”, the DNP protocol can be used over UDP/IP on channel 1 only. Refer to Appendix E for additional information on the
DNP protocol.
Changes to the DNP CHANNEL 1 PORT and DNP CHANNEL 2 PORT settings take effect only after power has
been cycled to the relay.
NOTE
The DNP NETWORK CLIENT ADDRESS settings can force the D60 to respond to a maximum of five specific DNP masters. The
settings in this sub-menu are shown below.
PATH: SETTINGS  PRODUCT SETUP  COMMUNICATIONS  DNP PROTOCOL  DNP NETWORK CLIENT ADDRESSES
 DNP NETWORK CLIENT ADDRESS 1: Range: standard IP address

 CLIENT ADDRESSES 0.0.0.0
CLIENT ADDRESS 2: Range: standard IP address
MESSAGE
0.0.0.0
5 MESSAGE
CLIENT ADDRESS 3:
0.0.0.0
Range: standard IP address

MESSAGE
0.0.0.0
MESSAGE
0.0.0.0
The DNP UNSOL RESPONSE FUNCTION should be “Disabled” for RS485 applications since there is no collision avoidance
mechanism. The DNP UNSOL RESPONSE TIMEOUT sets the time the D60 waits for a DNP master to confirm an unsolicited
response. The DNP UNSOL RESPONSE MAX RETRIES setting determines the number of times the D60 retransmits an unsolic-
ited response without receiving confirmation from the master; a value of “255” allows infinite re-tries. The DNP UNSOL
RESPONSE DEST ADDRESS is the DNP address to which all unsolicited responses are sent. The IP address to which unsolic-
ited responses are sent is determined by the D60 from the current TCP connection or the most recent UDP message.
The DNP scale factor settings are numbers used to scale analog input point values. These settings group the D60 analog
input data into the following types: current, voltage, power, energy, power factor, and other. Each setting represents the
scale factor for all analog input points of that type. For example, if the DNP VOLTAGE SCALE FACTOR setting is set to “1000”,
all DNP analog input points that are voltages will be returned with values 1000 times smaller (for example, a value of 72000
V on the D60 will be returned as 72). These settings are useful when analog input values must be adjusted to fit within cer-
tain ranges in DNP masters. Note that a scale factor of 0.1 is equivalent to a multiplier of 10 (that is, the value will be 10
times larger).
The DNP DEFAULT DEADBAND settings determine when to trigger unsolicited responses containing analog input data. These
settings group the D60 analog input data into the following types: current, voltage, power, energy, power factor, and other.
Each setting represents the default deadband value for all analog input points of that type. For example, to trigger unsolic-
ited responses from the D60 when any current values change by 15 A, the DNP CURRENT DEFAULT DEADBAND setting
should be set to “15”. Note that these settings are the deadband default values. DNP object 34 points can be used to
change deadband values, from the default, for each individual DNP analog input point. Whenever power is removed and
re-applied to the D60, the default deadbands will be in effect.
The DNP TIME SYNC IIN PERIOD setting determines how often the Need Time Internal Indication (IIN) bit is set by the D60.
Changing this time allows the DNP master to send time synchronization commands more or less often, as required.

The DNP MESSAGE FRAGMENT SIZE setting determines the size, in bytes, at which message fragmentation occurs. Large
fragment sizes allow for more efficient throughput; smaller fragment sizes cause more application layer confirmations to be
necessary which can provide for more robust data transfer over noisy communication channels.
When the DNP data points (analog inputs and/or binary inputs) are configured for Ethernet-enabled relays, check
the “DNP Points Lists” D60 web page to view the points lists. This page can be viewed with a web browser by enter-
NOTE
ing the D60 IP address to access the D60 “Main Menu”, then by selecting the “Device Information Menu” > “DNP
Points Lists” menu item.
The DNP OBJECT 1 DEFAULT VARIATION to DNP OBJECT 32 DEFAULT VARIATION settings allow the user to select the DNP
default variation number for object types 1, 2, 20, 21, 22, 23, 30, and 32. The default variation refers to the variation
response when variation 0 is requested and/or in class 0, 1, 2, or 3 scans. Refer to the DNP implementation section in
appendix E for additional details.
The DNP binary outputs typically map one-to-one to IED data points. That is, each DNP binary output controls a single
physical or virtual control point in an IED. In the D60 relay, DNP binary outputs are mapped to virtual inputs. However, some
legacy DNP implementations use a mapping of one DNP binary output to two physical or virtual control points to support
the concept of trip/close (for circuit breakers) or raise/lower (for tap changers) using a single control point. That is, the DNP
master can operate a single point for both trip and close, or raise and lower, operations. The D60 can be configured to sup-
port paired control points, with each paired control point operating two virtual inputs. The DNP NUMBER OF PAIRED CONTROL
POINTS setting allows configuration of from 0 to 32 binary output paired controls. Points not configured as paired operate on
a one-to-one basis.
The DNP ADDRESS setting is the DNP slave address. This number identifies the D60 on a DNP communications link. Each
DNP slave should be assigned a unique address.
The DNP TCP CONNECTION TIMEOUT setting specifies a time delay for the detection of dead network TCP connections. If
there is no data traffic on a DNP TCP connection for greater than the time specified by this setting, the connection will be
aborted by the D60. This frees up the connection to be re-used by a client.
5
Relay power must be re-cycled after changing the DNP TCP CONNECTION TIMEOUT setting for the changes to take
effect.
NOTE
i) DNP / IEC 60870-5-104 POINT LISTS

PATH: SETTINGS  PRODUCT SETUP  COMMUNICATIONS  DNP / IEC104 POINT LISTS
 DNP / IEC104  BINARY INPUT / MSP Range: see sub-menu below

 POINT LISTS  POINTS
 ANALOG INPUT / MME Range: see sub-menu below
MESSAGE
 POINTS
The binary and analog inputs points for the DNP protocol, or the MSP and MME points for IEC 60870-5-104 protocol, can
configured to a maximum of 256 points. The value for each point is user-programmable and can be configured by assigning
FlexLogic operands for binary inputs / MSP points or FlexAnalog parameters for analog inputs / MME points.
The menu for the binary input points (DNP) or MSP points (IEC 60870-5-104) is shown below.
PATH: SETTINGS  PRODUCT SETUP  COMMUNICATIONS  DNP / IEC104 POINT LISTS  BINARY INPUT / MSP POINTS
 BINARY INPUT / MSP Point: 0 Range: FlexLogic operand

 POINTS Off
Point: 1 Range: FlexLogic operand
MESSAGE
Off

Point: 255 Range: FlexLogic operand

MESSAGE
Off
Up to 256 binary input points can be configured for the DNP or IEC 60870-5-104 protocols. The points are configured by
assigning an appropriate FlexLogic operand. Refer to the Introduction to FlexLogic section in this chapter for the full range
of assignable operands.
The menu for the analog input points (DNP) or MME points (IEC 60870-5-104) is shown below.

PATH: SETTINGS  PRODUCT SETUP  COMMUNICATIONS  DNP / IEC104 POINT LISTS  ANALOG INPUT / MME POINTS
 ANALOG INPUT / MME Point: 0 Range: any FlexAnalog parameter

 POINTS Off
Point: 1 Range: any FlexAnalog parameter
MESSAGE
Off

Point: 255 Range: any FlexAnalog parameter

MESSAGE
Off
Up to 256 analog input points can be configured for the DNP or IEC 60870-5-104 protocols. The analog point list is config-
ured by assigning an appropriate FlexAnalog parameter to each point. Refer to Appendix A: FlexAnalog Parameters for the
full range of assignable parameters.
The DNP / IEC 60870-5-104 point lists always begin with point 0 and end at the first “Off” value. Since DNP / IEC
60870-5-104 point lists must be in one continuous block, any points assigned after the first “Off” point are ignored.
NOTE
Changes to the DNP / IEC 60870-5-104 point lists will not take effect until the D60 is restarted.
NOTE
j) IEC 61850 PROTOCOL

PATH: SETTINGS  PRODUCT SETUP  COMMUNICATIONS  IEC 61850 PROTOCOL
 IEC 61850 PROTOCOL  GSSE / GOOSE
5   CONFIGURATION
 SERVER
MESSAGE
 CONFIGURATION
 IEC 61850 LOGICAL
MESSAGE
 NODE NAME PREFIXES
 MMXU DEADBANDS
MESSAGE

 GGIO1 STATUS
MESSAGE
 CONFIGURATION
 GGIO2 CONTROL
MESSAGE
 CONFIGURATION
 GGIO4 ANALOG
MESSAGE
 CONFIGURATION
 GGIO5 UINTEGER
MESSAGE
 CONFIGURATION
 REPORT CONTROL
MESSAGE
 CONFIGURATION
 XCBR
MESSAGE
 CONFIGURATION
 XSWI
MESSAGE
 CONFIGURATION
The D60 Line Distance Protection System is provided with optional IEC 61850 communications capability.
This feature is specified as a software option at the time of ordering. Refer to the Ordering section of chap-
ter 2 for additional details.

Use independent ports for IEC 61850 communication and take care when configuring the settings,
else loss of protection or misoperation of the relay can result.
The D60 supports the Manufacturing Message Specification (MMS) protocol as specified by IEC 61850. MMS is supported
over two protocol stacks: TCP/IP over Ethernet. The D60 operates as an IEC 61850 server. The Remote inputs and outputs
section in this chapter describe the peer-to-peer GSSE/GOOSE message scheme.
The GSSE/GOOSE configuration main menu is divided into two areas: transmission and reception.
PATH: SETTINGS  PRODUCT SETUP  COMMUNICATIONS  IEC 61850 PROTOCOL  GSSE/GOOSE CONFIGURATION
 GSSE / GOOSE  TRANSMISSION

 CONFIGURATION 
 RECEPTION
MESSAGE

The main transmission menu is shown below:

 TRANSMISSION
 TRANSMISSION  GENERAL
 
 GSSE
MESSAGE

 FIXED GOOSE
MESSAGE

 CONFIGURABLE 5
MESSAGE
 GOOSE
The general transmission settings are shown below:

 TRANSMISSION  GENERAL
 GENERAL DEFAULT GSSE/GOOSE Range: 1 to 60 s in steps of 1
 UPDATE TIME: 60 s
The DEFAULT GSSE/GOOSE UPDATE TIME sets the time between GSSE or GOOSE messages when there are no remote out-
put state changes to be sent. When remote output data changes, GSSE or GOOSE messages are sent immediately. This
setting controls the steady-state heartbeat time interval.
The DEFAULT GSSE/GOOSE UPDATE TIME setting is applicable to GSSE, fixed D60 GOOSE, and configurable GOOSE.
The GSSE settings are shown below:
 TRANSMISSION  GSEE
 GSSE GSSE FUNCTION: Range: Enabled, Disabled
 Enabled
GSSE ID: Range: 65-character ASCII string
MESSAGE
GSSEOut
DESTINATION MAC: Range: standard MAC address
MESSAGE
000000000000
These settings are applicable to GSSE only. If the fixed GOOSE function is enabled, GSSE messages are not transmitted.
The GSSE ID setting represents the IEC 61850 GSSE application ID name string sent as part of each GSSE message. This
string identifies the GSSE message to the receiving device. In D60 releases previous to 5.0x, this name string was repre-
sented by the RELAY NAME setting.

The fixed GOOSE settings are shown below:

 TRANSMISSION  FIXED GOOSE
 FIXED GOOSE GOOSE FUNCTION: Range: Enabled, Disabled
 Disabled
GOOSE ID: Range: 65-character ASCII string
MESSAGE
GOOSEOut
DESTINATION MAC: Range: standard MAC address
MESSAGE
000000000000
GOOSE VLAN PRIORITY: Range: 0 to 7 in steps of 1
MESSAGE
4
GOOSE VLAN ID: Range: 0 to 4095 in steps of 1
MESSAGE
0
GOOSE ETYPE APPID: Range: 0 to 16383 in steps of 1
MESSAGE
0
These settings are applicable to fixed (DNA/UserSt) GOOSE only.

The GOOSE ID setting represents the IEC 61850 GOOSE application ID (GoID) name string sent as part of each GOOSE
message. This string identifies the GOOSE message to the receiving device. In revisions previous to 5.0x, this name string
was represented by the RELAY NAME setting.
The DESTINATION MAC setting allows the destination Ethernet MAC address to be set. This address must be a multicast
5 address; the least significant bit of the first byte must be set. In D60 releases previous to 5.0x, the destination Ethernet
MAC address was determined automatically by taking the sending MAC address (that is, the unique, local MAC address of
the D60) and setting the multicast bit.
The GOOSE VLAN PRIORITY setting indicates the Ethernet priority of GOOSE messages. This allows GOOSE messages to
have higher priority than other Ethernet data. The GOOSE ETYPE APPID setting allows the selection of a specific application
ID for each GOOSE sending device. This value can be left at its default if the feature is not required. Both the GOOSE VLAN
PRIORITY and GOOSE ETYPE APPID settings are required by IEC 61850.

The configurable GOOSE settings are shown below.

 TRANSMISSION  CONFIGURABLE GOOSE  CONFIGURABLE GOOSE 1(8)
 CONFIGURABLE CONFIG GSE 1 Range: Enabled, Disabled
 GOOSE 1 FUNCTION: Enabled
CONFIG GSE 1 ID: Range: 65-character ASCII string
MESSAGE
GOOSEOut_1
CONFIG GSE 1 DST MAC: Range: standard MAC address
MESSAGE
000000000000
CONFIG GSE 1 Range: 0 to 7 in steps of 1
MESSAGE
VLAN PRIORITY: 4
MESSAGE
VLAN ID: 0
MESSAGE
ETYPE APPID: 0
MESSAGE
CONFREV: 1
CONFIG GSE 1 RESTRANS Range: Aggressive, Medium, Relaxed, Heartbeat
MESSAGE
CURVE: Relaxed
 CONFIG GSE 1 Range: 64 data items; each can be set to all valid MMS
MESSAGE
 DATASET ITEMS data item references for transmitted data
5
The configurable GOOSE settings allow the D60 to be configured to transmit a number of different datasets within IEC
61850 GOOSE messages. Up to eight different configurable datasets can be configured and transmitted. This is useful for
intercommunication between D60 IEDs and devices from other manufacturers that support IEC 61850.
The configurable GOOSE feature allows for the configuration of the datasets to be transmitted or received from the D60.
The D60 supports the configuration of eight (8) transmission and reception datasets, allowing for the optimization of data
transfer between devices.
Items programmed for dataset 1 and 2 will have changes in their status transmitted as soon as the change is detected.
Datasets 1 and 2 should be used for high-speed transmission of data that is required for applications such as transfer trip-
ping, blocking, and breaker fail initiate. At least one digital status value needs to be configured in the required dataset to
enable transmission of configured data. Configuring analog data only to dataset 1 or 2 will not activate transmission.
Items programmed for datasets 3 through 8 will have changes in their status transmitted at a maximum rate of every
100 ms. Datasets 3 through 8 will regularly analyze each data item configured within them every 100 ms to identify if any
changes have been made. If any changes in the data items are detected, these changes will be transmitted through a
GOOSE message. If there are no changes detected during this 100 ms period, no GOOSE message will be sent.
For all datasets 1 through 8, the integrity GOOSE message will still continue to be sent at the pre-configured rate even if no
changes in the data items are detected.
The GOOSE functionality was enhanced to prevent the relay from flooding a communications network with GOOSE mes-
sages due to an oscillation being created that is triggering a message.
The D60 has the ability of detecting if a data item in one of the GOOSE datasets is erroneously oscillating. This can be
caused by events such as errors in logic programming, inputs improperly being asserted and de-asserted, or failed station
components. If erroneously oscillation is detected, the D60 will stop sending GOOSE messages from the dataset for a min-
imum period of one second. Should the oscillation persist after the one second time-out period, the D60 will continue to
block transmission of the dataset. The D60 will assert the MAINTENANCE ALERT: GGIO Ind XXX oscill self-test error mes-
sage on the front panel display, where XXX denotes the data item detected as oscillating.
For versions 5.70 and higher, the D60 supports four retransmission schemes: aggressive, medium, relaxed, and heartbeat.
The aggressive scheme is only supported in fast type 1A GOOSE messages (GOOSEOut 1 and GOOSEOut 2). For slow
GOOSE messages (GOOSEOut 3 to GOOSEOut 8) the aggressive scheme is the same as the medium scheme.

The details about each scheme are shown in the following table.
Table 5–5: GOOSE RETRANSMISSION SCHEMES

SCHEME SQ NUM TIME FROM THE TIME BETWEEN COMMENT TIME ALLOWED TO LIVE
EVENT MESSAGES IN MESSAGE
Aggressive 0 0 ms 0 ms Event 2000 ms
1 4 ms 4 ms T1 2000 ms
2 8 ms 4 ms T1 2000 ms
3 16 ms 8 ms T2 Heartbeat * 4.5
4 Heartbeat Heartbeat T0 Heartbeat * 4.5
Medium 0 0 ms 0 ms Event 2000 ms
1 16 ms 16 ms T1 2000 ms
2 32 ms 16 ms T1 2000 ms
Relaxed 0 0 ms 0 ms Event 2000 ms
1 100 ms 100 ms T1 2000 ms
2 200 ms 100 ms T1 2000 ms
5 5 Heartbeat Heartbeat T0 Heartbeat * 4.5
Heartbeat 0 0 ms 0 ms Event 2000 ms
1 Heartbeat Heartbeat T1 2000 ms
2 Heartbeat Heartbeat T1 2000 ms
The configurable GOOSE feature is recommended for applications that require GOOSE data transfer between UR-series
IEDs and devices from other manufacturers. Fixed GOOSE is recommended for applications that require GOOSE data
transfer between UR-series IEDs.
IEC 61850 GOOSE messaging contains a number of configurable parameters, all of which must be correct to achieve the
successful transfer of data. It is critical that the configured datasets at the transmission and reception devices are an exact
match in terms of data structure, and that the GOOSE addresses and name strings match exactly. Manual configuration is
possible, but third-party substation configuration software may be used to automate the process. The EnerVista UR Setup
software can produce IEC 61850 ICD files and import IEC 61850 SCD files produced by a substation configurator (refer to
the IEC 61850 IED configuration section later in this appendix).
The following example illustrates the configuration required to transfer IEC 61850 data items between two devices. The
general steps required for transmission configuration are:
1. Configure the transmission dataset.
2. Configure the GOOSE service settings.
3. Configure the data.
The general steps required for reception configuration are:
1. Configure the reception dataset.

This example shows how to configure the transmission and reception of three IEC 61850 data items: a single point status
value, its associated quality flags, and a floating point analog value.
The following procedure illustrates the transmission configuration.
1. Configure the transmission dataset by making the following changes in the PRODUCT SETUP  COMMUNICATION 
IEC 61850 PROTOCOL  GSSE/GOOSE CONFIGURATION  TRANSMISSION  CONFIGURABLE GOOSE  CONFIGURABLE
GOOSE 1  CONFIG GSE 1 DATASET ITEMS settings menu:
– Set ITEM 1 to “GGIO1.ST.Ind1.q” to indicate quality flags for GGIO1 status indication 1.
– Set ITEM 2 to “GGIO1.ST.Ind1.stVal” to indicate the status value for GGIO1 status indication 1.
– Set ITEM 3 to “MMXU1.MX.Hz.mag.f” to indicate the analog frequency magnitude for MMXU1 (the metered fre-
quency for SRC1).
The transmission dataset now contains a quality flag, a single point status Boolean value, and a floating point analog
value. The reception dataset on the receiving device must exactly match this structure.
2. Configure the GOOSE service settings by making the following changes in the PRODUCT SETUP  COMMUNICATION
 IEC 61850 PROTOCOL  GSSE/GOOSE CONFIGURATION  TRANSMISSION  CONFIGURABLE GOOSE  CONFIGU-
RABLE GOOSE 1 settings menu:
– Set CONFIG GSE 1 FUNCTION to “Enabled”.

– Set CONFIG GSE 1 ID to an appropriate descriptive string (the default value is “GOOSEOut_1”).
– Set CONFIG GSE 1 DST MAC to a multicast address (for example, 01 00 00 12 34 56).
– Set the CONFIG GSE 1 VLAN PRIORITY; the default value of “4” is OK for this example.
– Set the CONFIG GSE 1 VLAN ID value; the default value is “0”, but some switches may require this value to be “1”.
– Set the CONFIG GSE 1 ETYPE APPID value. This setting represents the ETHERTYPE application ID and must match 5
the configuration on the receiver (the default value is “0”).
– Set the CONFIG GSE 1 CONFREV value. This value changes automatically as described in IEC 61850 part 7-2. For
this example it can be left at its default value.
3. Configure the data by making the following changes in the PRODUCT SETUP  COMMUNICATION  IEC 61850 PROTO-
COL  GGIO1 STATUS CONFIGURATION settings menu:
– Set GGIO1 INDICATION 1 to a FlexLogic operand used to provide the status of GGIO1.ST.Ind1.stVal (for example, a
contact input, virtual input, a protection element status, etc.).
4. Configure the MMXU1 Hz Deadband by making the following changes in the PRODUCT SETUP  COMMUNICATION 
IEC 61850 PROTOCOL  MMXU DEADBANDS MMXU1 DEADBANDS settings menu:
– Set MMXU1 HZ DEADBAND to “0.050%”. This will result in an update to the MMXU1.MX.mag.f analog value with a
change greater than 45 mHz, from the previous MMXU1.MX.mag.f value, in the source frequency.
The D60 must be rebooted (control power removed and re-applied) before these settings take effect.
The following procedure illustrates the reception configuration.
1. Configure the reception dataset by making the following changes in the PRODUCT SETUP  COMMUNICATION  IEC
61850 PROTOCOL  GSSE/GOOSE CONFIGURATION  RECEPTION  CONFIGURABLE GOOSE  CONFIGURABLE GOOSE
1  CONFIG GSE 1 DATASET ITEMS settings menu:
– Set ITEM 3 to “GGIO3.MX.AnIn1.mag.f” to indicate the analog magnitude for GGIO3 analog input 1.
The reception dataset now contains a quality flag, a single point status Boolean value, and a floating point analog
value. This matches the transmission dataset configuration above.
2. Configure the GOOSE service settings by making the following changes in the INPUTS/OUTPUTS  REMOTE DEVICES
 REMOTE DEVICE 1 settings menu:
– Set REMOTE DEVICE 1 ID to match the GOOSE ID string for the transmitting device. Enter “GOOSEOut_1”.

– Set REMOTE DEVICE 1 ETYPE APPID to match the ETHERTYPE application ID from the transmitting device. This is
“0” in the example above.
– Set the REMOTE DEVICE 1 DATASET value. This value represents the dataset number in use. Since we are using
configurable GOOSE 1 in this example, program this value as “GOOSEIn 1”.
3. Configure the Boolean data by making the following changes in the INPUTS/OUTPUTS  REMOTE INPUTS  REMOTE
INPUT 1settings menu:
– Set REMOTE IN 1 DEVICE to “GOOSEOut_1”.
– Set REMOTE IN 1 ITEM to “Dataset Item 2”. This assigns the value of the GGIO3.ST.Ind1.stVal single point status
item to remote input 1.
4. Configure the analog data by making the following changes in the INPUTS/OUTPUTS  IEC 61850 GOOSE ANALOG
INPUTS settings menu:
– Set the IEC61850 GOOSE ANALOG INPUT 1 DEFAULT VALUE to “60.000”.
– Enter “Hz” for the IEC61850 GOOSE ANALOG INPUT 1 UNITS setting.
The GOOSE analog input 1 can now be used as a FlexAnalog value in a FlexElement or in other settings. The D60 must be
rebooted (control power removed and re-applied) before these settings take effect.
The value of GOOSE analog input 1 in the receiving device will be determined by the MMXU1.MX.Hz.mag.f value in the
sending device. This MMXU value is determined by the source 1 frequency value and the MMXU Hz deadband setting of
the sending device.
Remote input 1 can now be used in FlexLogic equations or other settings. The D60 must be rebooted (control power
removed and re-applied) before these settings take effect.
The value of remote input 1 (Boolean on or off) in the receiving device will be determined by the GGIO1.ST.Ind1.stVal value
5 in the sending device. The above settings will be automatically populated by the EnerVista UR Setup software when a com-
plete SCD file is created by third party substation configurator software.
For intercommunication between D60 IEDs, the fixed (DNA/UserSt) dataset can be used. The DNA/UserSt dataset con-
tains the same DNA and UserSt bit pairs that are included in GSSE messages. All GOOSE messages transmitted by the
D60 (DNA/UserSt dataset and configurable datasets) use the IEC 61850 GOOSE messaging services (for example, VLAN
support).
Set the CONFIG GSE 1 FUNCTION function to “Disabled” when configuration changes are required. Once changes are
entered, return the CONFIG GSE 1 FUNCTION to “Enabled” and restart the unit for changes to take effect.
NOTE
 TRANSMISSION  CONFIGURABLE GOOSE  CONFIGURABLE GOOSE 1(8)  CONFIG GSE 1(64) DATA ITEMS
 CONFIG GSE 1 ITEM 1: Range: all valid MMS data item references for
 DATASET ITEMS GGIO1.ST.Ind1.stVal transmitted data
ITEM 2: Range: all valid MMS data item references for

MESSAGE transmitted data
GGIO1.ST.IndPos1.stV
None

None
To create a configurable GOOSE dataset that contains an IEC 61850 Single Point Status indication and its associated qual-
ity flags, the following dataset items can be selected: “GGIO1.ST.Ind1.stVal” and “GGIO1.ST.Ind1.q”. The D60 will then cre-
ate a dataset containing these two data items. The status value for GGIO1.ST.Ind1.stVal is determined by the FlexLogic
operand assigned to GGIO1 indication 1. Changes to this operand will result in the transmission of GOOSE messages con-
taining the defined dataset.

The main reception menu is applicable to configurable GOOSE only and contains the configurable GOOSE dataset items
for reception:
 RECEPTION  CONFIGURABLE GOOSE  CONFIGURABLE GOOSE 1(16)  CONFIG GSE 1(32) DATA ITEMS
 CONFIG GSE 1 ITEM 1: Range: all valid MMS data item references for
 DATASET ITEMS GGIO3.ST.Ind1.stVal transmitted data

GGIO3.ST.IndPos1.stV
None

None
The configurable GOOSE settings allow the D60 to be configured to receive a number of different datasets within IEC
61850 GOOSE messages. Up to sixteen different configurable datasets can be configured for reception. This is useful for
intercommunication between D60 IEDs and devices from other manufacturers that support IEC 61850.
For intercommunication between D60 IEDs, the fixed (DNA/UserSt) dataset can be used. The DNA/UserSt dataset con-
tains the same DNA and UserSt bit pairs that are included in GSSE messages.
To set up a D60 to receive a configurable GOOSE dataset that contains two IEC 61850 single point status indications, the
following dataset items can be selected (for example, for configurable GOOSE dataset 1): “GGIO3.ST.Ind1.stVal” and
“GGIO3.ST.Ind2.stVal”. The D60 will then create a dataset containing these two data items. The Boolean status values from
these data items can be utilized as remote input FlexLogic operands. First, the REMOTE DEVICE 1(16) DATASET setting must 5
be set to contain dataset “GOOSEIn 1” (that is, the first configurable dataset). Then REMOTE IN 1(16) ITEM settings must be
set to “Dataset Item 1” and “Dataset Item 2”. These remote input FlexLogic operands will then change state in accordance
with the status values of the data items in the configured dataset.
Double-point status values may be included in the GOOSE dataset. Received values are populated in the
GGIO3.ST.IndPos1.stVal and higher items.
Floating point analog values originating from MMXU logical nodes may be included in GOOSE datasets. Deadband (non-
instantaneous) values can be transmitted. Received values are used to populate the GGIO3.MX.AnIn1 and higher items.
Received values are also available as FlexAnalog parameters (GOOSE analog In1 and up).
GGIO3.MX.AnIn1 to GGIO3.MX.AnIn32 can only be used once for all sixteen reception datasets.
NOTE

The main menu for the IEC 61850 server configuration is shown below.
PATH: SETTINGS  PRODUCT SETUP  COMMUNICATIONS  IEC 61850 PROTOCOL  SERVER CONFIGURATION
 SERVER IED NAME: IECDevice Range: up to 32 alphanumeric characters

 CONFIGURATION
LD INST: LDInst Range: up to 32 alphanumeric characters

MESSAGE
IEC/MMS TCP PORT Range: 0 to 65535 in steps of 1

MESSAGE
NUMBER: 102
INCLUDE NON-IEC Range: Disabled, Enabled

MESSAGE
DATA: Enabled
SERVER SCANNING: Range: Disabled, Enabled

MESSAGE
Disabled
LOCATION: LPHD DC PHV- Range: up to 80 alphanumeric characters

MESSAGE
Nam Location
LATITUDE: Range: -90.000 to 90.000 deg in steps of 0.001 deg

MESSAGE
LONGITUDE: Range: -180.000 to 180.000 deg in steps of 0.001 deg

MESSAGE
ALTITUDE: Range: 0 to 10,0000 m in steps of 1 m
5
MESSAGE
The IED NAME and LD INST settings represent the MMS domain name (IEC 61850 logical device) where all IEC/MMS logical
nodes are located. Valid characters for these values are upper and lowercase letters, numbers, and the underscore (_)
character, and the first character in the string must be a letter. This conforms to the IEC 61850 standard. The LOCATION is a
variable string and can be composed of ASCII characters. This string appears within the PhyName of the LPHD node.
The IEC/MMS TCP PORT NUMBER setting allows the user to change the TCP port number for MMS connections. The INCLUDE
NON-IEC DATA setting determines whether or not the “UR” MMS domain will be available. This domain contains a large num-
ber of UR-series specific data items that are not available in the IEC 61850 logical nodes. This data does not follow the IEC
61850 naming conventions. For communications schemes that strictly follow the IEC 61850 standard, this setting should be
“Disabled”.
When a 0 value is involved in a change, the changes to the IEC/MMS TCP PORT NUMBER setting take effect when the
D60 is restarted.
NOTE
The SERVER SCANNING feature should be set to “Disabled” when IEC 61850 client/server functionality is not required. IEC
61850 has two modes of functionality: GOOSE/GSSE inter-device communication and client/server communication. If the
GOOSE/GSSE functionality is required without the IEC 61850 client server feature, then server scanning can be disabled
to increase CPU resources. When server scanning is disabled, there is no updating of the IEC 61850 logical node status
values in the D60. Clients are still able to connect to the server (D60 relay), but most data values are not updated. This set-
ting does not affect GOOSE/GSSE operation.
Changes to the IED NAME setting, LD INST setting, and GOOSE dataset take effect when the D60 is restarted.
NOTE

The main menu for the IEC 61850 logical node name prefixes is shown below.
PATH: SETTINGS  PRODUCT SETUP  COMMUNICATIONS  IEC 61850 PROTOCOL
 IEC 61850 LOGICAL NODE NAME PREFIXES
 IEC 61850 LOGICAL  PIOC LOGICAL NODE
 NODE NAME PREFIXES  NAME PREFIXES
 PTOC LOGICAL NODE

MESSAGE
 NAME PREFIXES

 PTRC LOGICAL NODE

MESSAGE
 NAME PREFIXES
The IEC 61850 logical node name prefix settings are used to create name prefixes to uniquely identify each logical node.
For example, the logical node “PTOC1” may have the name prefix “abc”. The full logical node name will then be
“abcMMXU1”. Valid characters for the logical node name prefixes are upper and lowercase letters, numbers, and the
underscore (_) character, and the first character in the prefix must be a letter. This conforms to the IEC 61850 standard.
Changes to the logical node prefixes will not take effect until the D60 is restarted.
The main menu for the IEC 61850 MMXU deadbands is shown below.
PATH: SETTINGS  PRODUCT SETUP  COMMUNICATIONS  IEC 61850 PROTOCOL  MMXU DEADBANDS
 MMXU DEADBANDS  MMXU1 DEADBANDS

 
MESSAGE
 MMXU2 DEADBANDS

5
 MMXU3 DEADBANDS
MESSAGE

 MMXU4 DEADBANDS
MESSAGE

The MMXU deadband settings represent the deadband values used to determine when the update the MMXU “mag” and
“cVal” values from the associated “instmag” and “instcVal” values. The “mag” and “cVal” values are used for the IEC 61850
buffered and unbuffered reports. These settings correspond to the associated “db” data items in the CF functional con-
straint of the MMXU logical node, as per the IEC 61850 standard. According to IEC 61850-7-3, the db value “shall repre-
sent the percentage of difference between the maximum and minimum in units of 0.001%”. Thus, it is important to know the
maximum value for each MMXU measured quantity, since this represents the 100.00% value for the deadband.
The minimum value for all quantities is 0; the maximum values are as follows:
• phase current: 46  phase CT primary setting
• neutral current: 46  ground CT primary setting
• voltage: 275  VT ratio setting
• power (real, reactive, and apparent): 46  phase CT primary setting  275  VT ratio setting
• frequency: 90 Hz
• power factor: 2

The GGIO1 status configuration points are shown below:

PATH: SETTINGS  PRODUCT SETUP  COMMUNICATIONS  IEC 61850 PROTOCOL  GGIO1 STATUS CONFIGURATION
 GGIO1 STATUS NUMBER OF STATUS Range: 8 to 128 in steps of 8

 CONFIGURATION POINTS IN GGIO1: 8
GGIO1 INDICATION 1 Range: FlexLogic operand

MESSAGE
Off

MESSAGE
Off

MESSAGE
Off


MESSAGE
Off
The NUMBER OF STATUS POINTS IN GGIO1 setting specifies the number of “Ind” (single point status indications) that are
instantiated in the GGIO1 logical node. Changes to the NUMBER OF STATUS POINTS IN GGIO1 setting will not take effect until
the D60 is restarted.
The GGIO2 control configuration points are shown below:
PATH: SETTINGS  PRODUCT SETUP  COMMUNICATIONS  IEC 61850 PROTOCOL  GGIO2 CONTROL CONFIGURATION
 GGIO2 CF SPSCO 1(64)
5  GGIO2 CF SPCSO 1

GGIO2 CF SPCSO 1
CTLMODEL: 1
Range: 0, 1, or 2
The GGIO2 control configuration settings are used to set the control model for each input. The available choices are “0”
(status only), “1” (direct control), and “2” (SBO with normal security). The GGIO2 control points are used to control the D60
virtual inputs.
The GGIO4 analog configuration points are shown below:
PATH: SETTINGS  PRODUCT SETUP  COMMUNICATIONS  IEC 61850 PROTOCOL  GGIO4 ANALOG CONFIGURATION
 GGIO4 ANALOG NUMBER OF ANALOG Range: 4 to 32 in steps of 4

 CONFIGURATION POINTS IN GGIO4: 8
 GGIO4 ANALOG 1
MESSAGE
 MEASURED VALUE
 GGIO4 ANALOG 2
MESSAGE
 MEASURED VALUE
 GGIO4 ANALOG 3
MESSAGE
 MEASURED VALUE

 GGIO4 ANALOG 32
MESSAGE
 MEASURED VALUE
The NUMBER OF ANALOG POINTS setting determines how many analog data points will exist in GGIO4. When this value is
changed, the D60 must be rebooted in order to allow the GGIO4 logical node to be re-instantiated and contain the newly
configured number of analog points.

The measured value settings for each of the 32 analog values are shown below.
PATH: SETTINGS  PRODUCT...  COMMUNICATIONS  IEC 61850 PROTOCOL  GGIO4 ANALOG CONFIGURATION
 GGIO4 ANALOG 1(32) MEASURED VALUE
 GGIO4 ANALOG 1 ANALOG IN 1 VALUE: Range: any FlexAnalog value
 MEASURED VALUE Off
ANALOG IN 1 DB: Range: 0.000 to 100.000 in steps of 0.001

MESSAGE
0.000
ANALOG IN 1 MIN: Range: –1000000000.000 to 1000000000.000 in steps

MESSAGE of 0.001
0.000
ANALOG IN 1 MAX: Range: –1000000000.000 to 1000000000.000 in steps

MESSAGE of 0.001
0.000
These settings are configured as follows.

• ANALOG IN 1 VALUE: This setting selects the FlexAnalog value to drive the instantaneous value of each GGIO4 ana-
log status value (GGIO4.MX.AnIn1.instMag.f).
• ANALOG IN 1 DB: This setting specifies the deadband for each analog value. Refer to IEC 61850-7-1 and 61850-7-3
for details. The deadband is used to determine when to update the deadbanded magnitude from the instantaneous
magnitude. The deadband is a percentage of the difference between the maximum and minimum values.
• ANALOG IN 1 MIN: This setting specifies the minimum value for each analog value. Refer to IEC 61850-7-1 and
61850-7-3 for details. This minimum value is used to determine the deadband. The deadband is used in the determina-
tion of the deadbanded magnitude from the instantaneous magnitude.
• ANALOG IN 1 MAX: This setting defines the maximum value for each analog value. Refer to IEC 61850-7-1 and 5
61850-7-3 for details. This maximum value is used to determine the deadband. The deadband is used in the determi-
nation of the deadbanded magnitude from the instantaneous magnitude.
Note that the ANALOG IN 1 MIN and ANALOG IN 1 MAX settings are stored as IEEE 754 / IEC 60559 floating point
numbers. Because of the large range of these settings, not all values can be stored. Some values may be rounded
NOTE to the closest possible floating point number.
The GGIO5 integer configuration points are shown below:
PATH: SETTINGS  PRODUCT SETUP  COMMUNICATIONS  IEC 61850 PROTOCOL  GGIO5 ANALOG CONFIGURATION
 GGIO5 UINTEGER GGIO5 UINT In 1: Range: Off, any FlexInteger™ parameter

 CONFIGURATION Off
GGIO5 UINT In 2: Range: Off, any FlexInteger parameter

MESSAGE
Off
GGIO5 UINT In 3: Range: Off, any FlexInteger parameter

MESSAGE
Off

GGIO5 UINT 1n 16: Range: Off, any FlexInteger parameter

MESSAGE
Off
The GGIO5 logical node allows IEC 61850 client access to integer data values. This allows access to as many as 16
unsigned integer value points, associated timestamps, and quality flags. The method of configuration is similar to that of
GGIO1 (binary status values). The settings allow the selection of FlexInteger values for each GGIO5 integer value point.
It is intended that clients use GGIO5 to access generic integer values from the D60. Additional settings are provided to
allow the selection of the number of integer values available in GGIO5 (1 to 16), and to assign FlexInteger values to the
GGIO5 integer inputs. The following setting is available for all GGIO5 configuration points.
• GGIO5 UINT IN 1 VALUE: This setting selects the FlexInteger value to drive each GGIO5 integer status value
(GGIO5.ST.UIntIn1). This setting is stored as an 32-bit unsigned integer value.

The report control configuration settings are shown below:

PATH: SETTINGS  PRODUCT SETUP  COMMUNICATIONS  IEC 61850 PROTOCOL  REPORT CONTROL CONFIGURATION
 CONFIGURABLE REPORT 1  REPORT 1 DATASET ITEMS
 REPORT 1 ITEM 1: Range: all valid MMS data item references
 DATASET ITEMS
ITEM 2: Range: as shown above

MESSAGE

MESSAGE

MESSAGE
To create the dataset for logical node LN, program the ITEM 1 to ITEM 64 settings to a value from the list of IEC 61850 data
attributes supported by the D60. Changes to the dataset will only take effect when the D60 is restarted. It is recommended
to use reporting service from logical node LLN0 if a user needs some (but not all) data from already existing GGIO1,
GGIO4, and MMXU4 points and their quantity is not greater than 64 minus the number items in this dataset.

The breaker configuration settings are shown below. Changes to these values take effect when the UR is restarted:
PATH: SETTINGS  PRODUCT SETUP  COMMUNICATIONS  IEC 61850 PROTOCOL  XCBR CONFIGURATION
 XCBR XCBR1 ST.LOC OPERAND Range: FlexLogic operand

 CONFIGURATION Off

XCBR6 ST.LOC OPERAND Range: FlexLogic operand

MESSAGE
Off
CLEAR XCBR1 OpCnt: Range: No, Yes

MESSAGE
No

CLEAR XCBR6 OpCnt: Range: No, Yes

MESSAGE
No
XCBR1 SYNCCHECK CLS: Range: FlexLogic operand

MESSAGE
Off

XCBR6 SYNCCHECK CLS: Range: FlexLogic operand

MESSAGE
Off
XCBR1 INTERLOCK OPN: Range: FlexLogic operand

MESSAGE
Off

5
XCBR6 INTERLOCK OPN: Range: FlexLogic operand
MESSAGE
Off
XCBR1 INTERLOCK CLS: Range: FlexLogic operand

MESSAGE
Off

XCBR6 INTERLOCK CLS: Range: FlexLogic operand

MESSAGE
Off
XCBR1 Pos ctlModel: Range: 0 to 4 (as per IEC 61850-7-3, ctlModel)

MESSAGE
2

XCBR6 Pos ctlModel: Range: 0 to 4 (as per IEC 61850-7-3, ctlModel)

MESSAGE
2
XCBR1 Pos Range: 2 to 60 seconds

MESSAGE
sboTimeout: 30 s

XCBR6 Pos Range: 2 to 60 seconds

MESSAGE
sboTimeout: 30 s
The XCBR1 ST.LOC OPERAND setting is used to inhibit 61850 control commands to close or open breaker through UR
Breaker Control element. See the Breaker Control element logic diagram for more information.
The CLEAR XCBR1 OpCnt setting allows clearing the breaker operating counter. As breakers operate by opening and
closing, the XCBR operating counter status attribute (OpCnt) increments with every operation. Frequent breaker operation
can result in very large OpCnt values over time. This setting allows the OpCnt to be reset to “0” for XCBR1.

The XCBR1 SYNCCHECK CLS setting is used to supervise a close command with a synchrocheck condition within XCBR
logical node. If a Close with SynchroCheck is requested (through a SelectWithValue service) and the SynchroCheck condi-
tion is not satisfied, a Negative Response (-Rsp) is issued with the REASON CODE of Blocked-by-synchrocheck.
The XCBR1 INTERLOCK OPN/CLS settings are used to assign an operand, which is linked into the EnaOpn or EnaCls
INTERLOCKED inputs respectively of the XCBR. When this operand is asserted, XCBR logical node inhibits execution of
the open and close commands respectively. If select before operate (SBO) with Extended Security is requested and Inter-
lock condition exists, the UR responds with a Negative response (-Rsp) with the Reason Code Blocked-by-interlocking.
The XCBR1 Pos ctlModel setting is used to select control model per IEC 61850-7-3. The following control models are sup-
ported by URs:
0 — Status only
1 — Direct control with normal security (direct-operate)
2 — SBO control with normal security (operate-once)
3 — Direct control with enhanced security (direct-operate)
4 — SBO control with enhanced security (operate-once)
See IEC 61850-7-2 for complete details on these control models.
The XCBR1 Pos sboTimeout setting is used to select SBO timeout value. To be successful, the IEC 61850 "operate" com-
mand must be executed after the "select" command within the XCBR1 Pos sboTimeout setting value.
The disconnect switch configuration settings are shown below. Changes to these values will not take effect until the UR is
restarted:
PATH: SETTINGS  PRODUCT SETUP  COMMUNICATIONS  IEC 61850 PROTOCOL  XSWI CONFIGURATION
5  XSWI
 CONFIGURATION
XSWI1 ST.LOC OPERAND
Off
XSWI2 ST.LOC OPERAND Range: FlexLogic operand

MESSAGE
Off

MESSAGE
Off


MESSAGE
Off
CLEAR XSWI1 OpCnt: Range: No, Yes

MESSAGE
No

MESSAGE
No

MESSAGE
No


MESSAGE
No
The CLEAR XSWI1 OpCnt setting represents the disconnect switch operating counter. As disconnect switches operate by
opening and closing, the XSWI operating counter status attribute (OpCnt) increments with every operation. Frequent switch
operation may result in very large OpCnt values over time. This setting allows the OpCnt to be reset to “0” for XSWI1.
Since GSSE/GOOSE messages are multicast Ethernet by specification, they are not usually be forwarded by net-
work routers. However, GOOSE messages may be forwarded by routers if the router has been configured for VLAN
NOTE functionality.

k) WEB SERVER HTTP PROTOCOL

PATH: SETTINGS  PRODUCT SETUP  COMMUNICATIONS  WEB SERVER HTTP PROTOCOL
 WEB SERVER HTTP TCP PORT Range: 0 to 65535 in steps of 1

 HTTP PROTOCOL NUMBER: 80
The D60 contains an embedded web server and is capable of transferring web pages to a web browser such as Internet
Explorer or Firefox. The web pages are organized as a series of menus that can be accessed starting at the D60 “Main
Menu”. Web pages are available showing DNP and IEC 60870-5-104 points lists, Modbus registers, event records, fault
reports, and so on. First connect the UR and a computer to an Ethernet network, then enter the IP address of the D60 into
the “Address” box of the web browser.
When the port is set to 0, the change takes effect when the D60 is restarted.
NOTE
l) TFTP PROTOCOL
PATH: SETTINGS  PRODUCT SETUP  COMMUNICATIONS  TFTP PROTOCOL
 TFTP PROTOCOL TFTP MAIN UDP PORT Range: 0 to 65535 in steps of 1

 NUMBER: 69
TFTP DATA UDP PORT 1 Range: 0 to 65535 in steps of 1
MESSAGE
NUMBER: 0
TFTP DATA UDP PORT 2 Range: 0 to 65535 in steps of 1
MESSAGE
NUMBER: 0
The Trivial File Transfer Protocol (TFTP) can be used to transfer files from the D60 over a network. The D60 operates as a
TFTP server. TFTP client software is available from various sources, including Microsoft Windows NT. The dir.txt file
5
obtained from the D60 contains a list and description of all available files (event records, oscillography, etc.).
When the TFTP MAIN UDP PORT NUMBER is set to 0, the change takes effect when the D60 is restarted.
NOTE

m) IEC 60870-5-104 PROTOCOL

PATH: SETTINGS  PRODUCT SETUP  COMMUNICATIONS  IEC 60870-5-104 PROTOCOL
 IEC 60870-5-104 IEC 60870-5-104 Range: Enabled, Disabled

 PROTOCOL FUNCTION: Disabled
IEC TCP PORT Range: 0 to 65535 in steps of 1
MESSAGE
NUMBER: 2404
 IEC NETWORK Range: see sub-menu below
MESSAGE
 CLIENT ADDRESSES
IEC COMMON ADDRESS Range: 0 to 65535 in steps of 1
MESSAGE
OF ASDU: 0
IEC CYCLIC DATA Range: 1 to 65535 s in steps of 1
MESSAGE
PERIOD: 60 s
IEC CURRENT DEFAULT Range: 0 to 65535 in steps of 1
MESSAGE
THRESHOLD: 30000
IEC VOLTAGE DEFAULT Range: 0 to 65535 in steps of 1
MESSAGE
THRESHOLD: 30000
IEC POWER DEFAULT Range: 0 to 65535 in steps of 1
MESSAGE
THRESHOLD: 30000
IEC ENERGY DEFAULT Range: 0 to 65535 in steps of 1
MESSAGE
THRESHOLD: 30000
5 IEC PF DEFAULT Range: 0.00 to 1.00
MESSAGE
THRESHOLD: 1.00
IEC OTHER DEFAULT Range: 0 to 65535 in steps of 1
MESSAGE
THRESHOLD: 30000
IEC REDUNDANCY Range: No, Yes
MESSAGE
ENABLED: No
The D60 supports the IEC 60870-5-104 protocol. The D60 can be used as an IEC 60870-5-104 slave device connected to
a maximum of two masters (usually either an RTU or a SCADA master station). Since the D60 maintains two sets of IEC
60870-5-104 data change buffers, no more than two masters should actively communicate with the D60 at one time.
The IEC ------- DEFAULT THRESHOLD settings are used to determine when to trigger spontaneous responses containing
M_ME_NC_1 analog data. These settings group the D60 analog data into types: current, voltage, power, energy, and other.
Each setting represents the default threshold value for all M_ME_NC_1 analog points of that type. For example, to trigger
spontaneous responses from the D60 when any current values change by 15 A, the IEC CURRENT DEFAULT THRESHOLD set-
ting should be set to 15. Note that these settings are the default values of the deadbands. P_ME_NC_1 (parameter of mea-
sured value, short floating point value) points can be used to change threshold values, from the default, for each individual
M_ME_NC_1 analog point. Whenever power is removed and re-applied to the D60, the default thresholds are in effect.
The IEC REDUNDANCY setting decides whether multiple client connections are accepted or not. If redundancy is set to Yes,
two simultaneous connections can be active at any given time.
When the IEC port number is set to 0, the change takes effect when the D60 is restarted.
NOTE
The IEC 60870-5-104 and DNP protocols cannot be used simultaneously. When the IEC 60870-5-104 FUNCTION
setting is set to “Enabled”, the DNP protocol does not operate. When this setting is changed, it takes effect when
NOTE
power to the relay is cycled (off-to-on).

PATH: SETTINGS  PRODUCT SETUP  COMMUNICATIONS  IEC 60870-5-104 PROTOCOL  IEC NETWORK CLIENT
ADDRESSES
 IEC NETWORK CLIENT ADDRESS 1: Range: Standard IPV4 address format

 CLIENT ADDRESSES 0.0.0.0
CLIENT ADDRESS 2: Range: Standard IPV4 address format
MESSAGE
0.0.0.0
MESSAGE
0.0.0.0
MESSAGE
0.0.0.0
MESSAGE
0.0.0.0
The UR can specify a maximum of five clients for its IEC 104 connections. These are IP addresses for the controllers to
which the UR can connect.
A maximum of two simultaneous connections are supported at any given time.
5.2.5 MODBUS USER MAP
PATH: SETTINGS  PRODUCT SETUP  MODBUS USER MAP
 MODBUS USER MAP ADDRESS 1: 0 Range: 0 to 65535 in steps of 1

 VALUE: 0
Range: 0 to 65535 in steps of 1
5
ADDRESS 2: 0
MESSAGE
VALUE: 0
ADDRESS 3: 0 Range: 0 to 65535 in steps of 1
MESSAGE
VALUE: 0

ADDRESS 256: 0 Range: 0 to 65535 in steps of 1

MESSAGE
VALUE: 0
The Modbus user map provides read-only access for up to 256 registers. To obtain a memory map value, enter the desired
address in the ADDRESS line (converted from hex to decimal format). The corresponding value displays in the VALUE line. A
value of “0” in subsequent register ADDRESS lines automatically returns values for the previous ADDRESS lines incremented
by “1”. An address value of “0” in the initial register means “none” and values of “0” display for all registers. Different
ADDRESS values can be entered as required in any of the register positions.

5.2.6 REAL TIME CLOCK
a) MAIN MENU
PATH: SETTINGS  PRODUCT SETUP  REAL TIME CLOCK
 REAL TIME SYNCRONIZING SOURCE: Range: None, PP/IRIG-B/PTP/SNTP, IRIG-B/PP/PTP/

 CLOCK None SNTP, PP/PTP/IRIG-B/SNTP
REAL TIME CLOCK

MESSAGE Range:Enabled, Disabled
EVENTS: Disabled
IRIG-B SIGNAL TYPE:
MESSAGE Range:None, DC Shift, Amplitude Modulated
None
 PRECISION TIME
MESSAGE See below
 PROTOCOL (1588)
 SNTP PROTOCOL
MESSAGE See below

 LOCAL TIME
MESSAGE See below

The relay contains a real time clock (RTC) to create timestamps for communications protocols as well as for historical data,
such as event records and oscillography. When the relay restarts, the RTC initializes from an onboard battery-backed
clock, which has the same accuracy as an electronic watch, approximately ±1 minute per month (~23 ppm). Once the RTC
is synchronized with the Precision Time Protocol (PTP), IRIG-B, or SNTP, its accuracy approaches that of the synchroniz-
ing time delivered to the relay.
5 The SYNCHRONIZING SOURCE setting configures the priority sequence that the relay uses to determine which of the avail-
able external time sources synchronizes the RTC and the synchrophasor clock. A setting of None causes the RTC and the
synchrophasor clock to free-run. A setting of PP/IRIGB/PTP/SNTP, IRIGB/PP/PTP/SNTP, or PP/PTP/IRIGB/SNTP causes
the relay to track the first source named that is enabled and operational, or free-run if none of these are available. Here, PP
means a time source that is strictly compliant with PP, PTP means a time source that is not strictly compliant with PP. When
a time source fails or recovers, the relay automatically transfers synchronization as required by this setting.
See the COMMANDS SET DATE AND TIME menu section of this manual to manually set the RTC.
The REAL TIME CLOCK EVENTS setting allows changes to the date and/or time to be captured in the event record. The event
records the RTC time before the adjustment.
To enable IRIG-B synchronization, the input IRIG-B SIGNAL TYPE must be set to DC Shift or Amplitude Modulated. IRIG-B
synchronization can be disabled by making this setting None.
To configure and enable PTP and/or SNTP, or to set local time parameters (for example time zone, daylight savings), use
the following sections.
b) PRECISION TIME PROTOCOL (1588)

PATH: SETTINGS  PRODUCT SETUP  REAL TIME CLOCK  PRECISION TIME PROTOCOL (1588)
 PRECISION TIME STRICT POWER PROFILE: Range: Enabled, Disabled

 PROTOCOL (1588) Disabled
PTP DOMAIN NUMBER Range: 0 to 255
MESSAGE
0
PTP VLAN PRIORITY Range: 0 to 7
MESSAGE
4
PTP VLAN ID Range: 0 to 4095
0
 PTP PORT 1
MESSAGE


PATH: SETTINGS  PRODUCT SETUP  REAL TIME CLOCK  PRECISION TIME PROTOCOL (1588)  PTP PORT 1(3)
PORT 1 PTP FUNCTION: Range: Enabled, Disabled

MESSAGE
Disabled
PORT 1 PATH DELAY Range: 0 to 60 000 ns in steps of 1
MESSAGE
ADDER: 00000 ns
PORT 1 PATH DELAY Range: –1 000 to +1 000 ns in steps of 1
MESSAGE
ASYMMETRY: 0000 ns
The UR supports the Precision Time Protocol (PTP) specified in IEEE Std 1588 2008 using the Power Profile (PP) specified
in IEEE Std C37.238 2011. This enables the relay to synchronize to the international time standard over an Ethernet net-
work that implements PP.
The relay can be configured to operate on some PTP networks that are not strictly PP. Time accuracy can be less than
specified for a PP network. Tolerated deviations from strict PP include 1) missing declaration of PP compliance in the mes-
sages, 2) connection to a network device that does not support the PTP peer delay mechanism, 3) jitter substantially
greater than 1 µs in received event messages, and 4) certain non-compliant announce and sync message update rates.
The relay implements PTP according to IEEE Std 1588 2008 and the equivalent IEC 61588:2009(E), sometimes
referred to as version 2 PTP. It does not support the previous version of the standard (version 1).
NOTE
PTP is a protocol that allows multiple clocks in a network to synchronize with one another. It permits synchronization accu-
racies better than 1 ns, but this requires each and every component in the network achieve very high levels of accuracy and
a very high baud rate, faster than normally used for relay communications. When operating over a generic Ethernet net-
work, time error may amount to 1 ms or more. PP is a profile of PTP which specifies a limited subset of PTP suitable for use
in power system protection, control, automation and data communication applications, and thereby facilitates interoperabil-
ity between different vendor’s clocks and switches. PP specifies a worst-case delivered time error of less than 1 µs over a
5
16-hop network.
In a PTP system and in a PP system, the clocks automatically organize themselves into a master-slave synchronization
hierarchy with the “best” clock available making itself the "grandmaster" at the top of the hierarchy; all others make them-
selves “slaves” and track the grandmaster. Typically the grandmaster clock receives its time from GPS satellites or some
other link to the international time standard. If the grandmaster fails, the next “best” clock available in the domain assumes
the grandmaster role. Should a clock on starting up discover it is “better” that the present grandmaster, it assumes the
grandmaster role and the previous grandmaster reverts to slave.
Time messages issued by the grandmaster are delayed as they pass through the network both due to the finite speed of
the signal in the interconnecting fiber or wire. Each clock and switch implementing PP measures the propagation delay to
each of its PP neighbors, and compensates for these delays in the time received. Each network device implementing PP
measures the processing delay it introduces in each time message and compensates for this delay in the time it transmits.
As a result, the time delivered to end-devices such as the UR are virtually identical to the grandmaster time. Should one of
the network devices in the hierarchy not fully implement PP, the associated propagation delay and/or latency may not be
compensated for, and the time received at the end-device could be in error by more than 100 µs.
See the Settings > Product Setup > Real Time Clock section of this manual for a description of when time values
received via PTP are used to update the relay’s real time clock.
The following settings are available for configuring the relay for PTP.
STRICT POWER PROFILE
• Power profile (IEEE Std C37.238 2011) requires that the relay only select as a grandmaster power profile compliant
clocks, that the delivered time have worst-case error of ±1 µs, and that the peer delay mechanism be implemented.
With the strict power profile setting enabled, the relay will only select as master clocks displaying the IEEE_C37_238
identification codes. It will use a port only when the peer delay mechanism is operational. With the strict power profile
setting disabled, the relay will use clocks without the power profile identification when no power profile clocks are pres-
ent, and will use ports even if the peer delay mechanism is non-operational.
• This setting applies to all of the relay’s PTP capable ports.

PTP DOMAIN NUMBER

• This setting should be set to the domain number of the grandmaster-capable clock(s) to be synchronized to. A net-
work may support multiple time distribution domains, each distinguished with a unique domain number. More com-
monly, there is a single domain using the default domain number zero.
PTP VLAN PRIORITY
• This setting selects the value of the priority field in the 802.1Q VLAN tag in request messages issued by the relay’s
peer delay mechanism. In compliance with PP the default VLAN priority is 4, but it is recommended that in accordance
with PTP it be set to 7.
• Depending on the characteristics of the device to which the relay is directly linked, VLAN Priority may have no effect.
PTP VLAN ID
• This setting selects the value of the ID field in the 802.1Q VLAN tag in request messages issued by the relay’s peer
delay mechanism. It is provided in compliance with PP. As these messages have a destination address that indicates
they are not to be bridged, their VLAN ID serves no function, and so may be left at its default value.
• Depending on the characteristics of the device to which the relay is directly linked, VLAN ID may have no effect.
PORT 1 ... 3 FUNCTION
• While this port setting is selected to disabled, PTP is disabled on this port. The relay does not generate or listen to
PTP messages on this port.
5 PORT 1 ... 3 PATH DELAY ADDER
• The time delivered by PTP is advanced by the time value in this setting prior to the time being used to synchronize the
relay’s real time clock. This is to compensate to the extent practical for time delivery delays not compensated for in the
network. In a fully compliant PP network, the peer delay and the processing delay mechanisms compensate for all the
delays between the grandmaster and the relay. In such networks, this setting should be zero.
• In networks containing one or more switches and/or clocks that do not implement both of these mechanisms, not all
delays are compensated, so the time of message arrival at the relay will be later than the time indicated in the mes-
sage. This setting can be used to approximately compensate for this delay. However, as the relay is not aware of net-
work switching that dynamically changes the amount of uncompensated delay, there is no setting that will always
completely correct for uncompensated delay. A setting can be chosen that will reduce worst-case error to half of the
range between minimum and maximum uncompensated delay, if these values are known.
PORT 1 ... 3 PATH DELAY ASYMMETRY
• This setting corresponds to “delayAsymmetry” in PTP, which is used by the peer delay mechanism to compensate for
any difference in the propagation delay between the two directions of a link. Except in unusual cases, the two fibers are
of essentially identical length and composition, so this setting should be set to zero.
• In unusual cases where the length of the link is different in different directions, this setting should be set to the number
of nanoseconds the Ethernet propagation delay to the relay is longer than the mean of path propagation delays to and
from the relay. For instance, if it is known say from the physical length of the fibers and the propagation speed in the
fibers that the delay from the relay to the Ethernet switch it is connected to is 9 000 ns and the that the delay from the
switch to the relay is 11 000 ns, then the mean delay is 10 000 ns, and the path delay asymmetry is 11000 - 10000 =
+1000 ns.

c) SNTP PROTOCOL
PATH: SETTINGS  PRODUCT SETUP  REAL TIME CLOCK  SNTP PROTOCOL
 SNTP PROTOCOL SNTP FUNCTION: Range: Enabled, Disabled

 Disabled
SNTP SERVER IP ADDR: Range: Standard IP address format
MESSAGE
0.0.0.0
SNTP UDP PORT Range: 0 to 65535 in steps of 1
MESSAGE
NUMBER: 123
The D60 supports the Simple Network Time Protocol specified in RFC-2030. With SNTP, the D60 can obtain clock time
over an Ethernet network. The D60 acts as an SNTP client to receive time values from an SNTP/NTP server, usually a ded-
icated product using a GPS receiver to provide an accurate time. Unicast SNTP is supported. The UR-series relays do not
support the broadcast, multicast or anycast SNTP functionality.
The SNTP FUNCTION setting enables or disabled the SNTP feature on the D60.
To use SNTP, SNTP SERVER IP ADDR must be set to the SNTP/NTP server IP address. Once this address is set and SNTP
FUNCTION is “Enabled”, the D60 attempts to obtain time values from the SNTP/NTP server. Since many time values are
obtained and averaged, it generally takes three to four minutes until the D60 clock is closely synchronized with the SNTP/
NTP server. It takes up to two minutes for the D60 to signal an SNTP self-test error if the server is offline.
The SNTP UDP PORT NUMBER is 123 for normal SNTP operation. If SNTP is not required, close the port by setting it to 0.
When the SNTP UDP PORT NUMBER is set to 0, the change takes effect when the D60 is restarted.
NOTE
d) LOCAL TIME 5
PATH: SETTINGS  PRODUCT SETUP  REAL TIME CLOCK  LOCAL TIME
 LOCAL TIME LOCAL TIME OFFSET Range: –24.0 to 24.0 hrs in steps of 0.5
 FROM UTC: 0.0 hrs
DAYLIGHT SAVINGS Range: Disabled, Enabled
MESSAGE
TIME: Disabled
DST START MONTH: Range: January to December (all months)
MESSAGE
January
DST START DAY: Range: Sunday to Saturday (all days of the week)
MESSAGE
Sunday
DST START DAY Range: First, Second, Third, Fourth, Last
MESSAGE
INSTANCE: First
DST START HOUR: Range: 0 to 23
MESSAGE
2
DST STOP MONTH: Range: January to December (all months)
MESSAGE
January
DST STOP DAY: Range: Sunday to Saturday (all days of the week)
MESSAGE
Sunday
DST STOP DAY Range: First, Second, Third, Fourth, Last
MESSAGE
INSTANCE: First
DST STOP HOUR: Range: 0 to 23
MESSAGE
2
The UR device maintains two times: local time and Universal Coordinated Time (UTC). Local time can be provided by IRIG-
B signals. UTC time is provided by SNTP servers.

The real-time clock (RTC) and communication protocol times are not correct unless Local Time is configured for the current
location. When the RTC is synchronized with IRIG-B, Local Time must be configured for the current location or else the
timestamps may not be accurate. Furthermore, times reported in historical records and communication protocols may be
incorrect if the Local Time setting is not configured properly.
The LOCAL TIME OFFSET FROM UTC setting is used to specify the local time zone offset from UTC (Greenwich Mean Time) in
hours. Time zones in the eastern hemisphere have positive values; time zones in the western hemisphere have negative
values. A value of zero causes the relay to use UTC for local time. This setting has two uses. When the system RTC is syn-
chronized with a communications protocol providing only local time or it is free-running, the offset setting is used to calcu-
late UTC from the local time these provide. When the RTC is synchronized with a communications protocol providing only
UTC (such as PTP or SNTP), the time offset setting is used to determine local time from the UTC provided. PTP
ALTERNATE_TIME_OFFSET_INDICATOR TLVs are not used to calculate local time. When a communications protocol
other than PTP provides UTC to local time offset (meaning IRIG-B), that offset is used instead of the local time and daylight
time settings.
The DAYLIGHT SAVINGS TIME (DST) settings can be used to allow the relay to follow the DST rules of the local time zone.
Note that when IRIG-B time synchronization is active, the local time in the IRIG-B signal contains any daylight savings time
offset and so the DST settings are ignored.
5.2.7 FAULT REPORTS
PATH: SETTINGS  PRODUCT SETUP  FAULT REPORTS  FAULT REPORT 1
 FAULT REPORT 1 FAULT REPORT 1 Range: SRC 1, SRC 2, SRC 3, SRC 4

 SOURCE: SRC 1
FAULT REPORT 1 TRIG: Range: FlexLogic operand
5
MESSAGE
Off
FAULT REPORT 1 Z1 Range: 0.01 to 250.00 ohms in steps of 0.01
MESSAGE
MAG: 3.00 
FAULT REPORT 1 Z1 Range: 25 to 90° in steps of 1
MESSAGE
ANGLE: 75°
FAULT REPORT 1 Z0 Range: 0.01 to 650.00 ohms in steps of 0.01
MESSAGE
MAG: 9.00 
FAULT REPORT 1 Z0 Range: 25 to 90° in steps of 1
MESSAGE
ANGLE: 75°
FAULT REPORT 1 LINE Range: km, miles
MESSAGE
LENGTH UNITS: km
FAULT REP 1 LENGTH Range: 0.0 to 2000.0 in steps of 0.1
MESSAGE
(km ): 100.0
FAULT REPORT 1 VT Range: None, I0, V0
MESSAGE
SUBSTITUTION: None
FAULT REP 1 SYSTEM Range: 0.01 to 650.00 ohms in steps of 0.01
MESSAGE
Z0 MAG: 2.00 
FAULT REP 1 SYSTEM Range: 25 to 90° in steps of 1
MESSAGE
Z0 ANGLE: 75°
The D60 relay supports one fault report and an associated fault locator. The signal source and trigger condition, as well as
the characteristics of the line or feeder, are entered in this menu.
The fault report stores data, in non-volatile memory, pertinent to an event when triggered. The captured data contained in
the FaultReport.txt file includes:
• Fault report number.
• Name of the relay, programmed by the user.

• Firmware revision of the relay.

• Date and time of trigger.
• Name of trigger (specific operand).
• Line or feeder ID via the name of a configured signal source.
• Active setting group at the time of trigger.
• Pre-fault current and voltage phasors (two cycles before either a 50DD disturbance associated with fault report source
or the trigger operate). Once a disturbance is detected, pre-fault phasors hold for 3 seconds waiting for the fault report
trigger. If trigger does not occur within this time, the values are cleared to prepare for the next disturbance.
• Fault current and voltage phasors (one cycle after the trigger).
• Elements operated at the time of triggering.
• Events: 9 before trigger and 7 after trigger (only available via the relay webpage).
• Fault duration times for each breaker (created by the breaker arcing current feature).
The captured data also includes the fault type and the distance to the fault location, as well as the reclose shot number
(when applicable) To include fault duration times in the fault report, the user must enable and configure breaker arcing cur-
rent feature for each of the breakers. Fault duration is reported on a per-phase basis.
The relay allows locating faults, including ground faults, from delta-connected VTs. In this case, the missing zero-sequence
voltage is substituted either by the externally provided neutral voltage (broken delta VT) connected to the auxiliary voltage
channel of a VT bank, or by the zero-sequence voltage approximated as a voltage drop developed by the zero-sequence
current, and user-provided zero-sequence equivalent impedance of the system behind the relay.
The trigger can be any FlexLogic operand, but in most applications it is expected to be the same operand, usually a virtual
output, that is used to drive an output relay to trip a breaker. To prevent the overwriting of fault events, the disturbance
detector should not be used to trigger a fault report. A FAULT RPT TRIG event is automatically created when the report is
5
triggered.
If a number of protection elements are ORed to create a fault report trigger, the first operation of any element causing the
OR gate output to become high triggers a fault report. However, If other elements operate during the fault and the first oper-
ated element has not been reset (the OR gate output is still high), the fault report is not triggered again. Considering the
reset time of protection elements, there is very little chance that fault report can be triggered twice in this manner. As the
fault report must capture a usable amount of pre and post-fault data, it can not be triggered faster than every 20 ms.
Each fault report is stored as a file; the relay capacity is fifteen (15) files. An sixteenth (16th) trigger overwrites the oldest
file.
The EnerVista UR Setup software is required to view all captured data. The relay faceplate display can be used to view the
date and time of trigger, the fault type, the distance location of the fault, and the reclose shot number.
The FAULT REPORT 1 SOURCE setting selects the source for input currents and voltages and disturbance detection.
The FAULT 1 REPORT TRIG setting assigns the FlexLogic operand representing the protection element/elements requiring
operational fault location calculations. The distance to fault calculations are initiated by this signal. The FAULT REPORT 1 Z1
MAG and FAULT REPORT 1 Z0 MAG impedances are entered in secondary ohms.
The FAULT REPORT 1 VT SUBSTITUTION setting shall be set to “None” if the relay is fed from wye-connected VTs. If delta-con-
nected VTs are used, and the relay is supplied with the neutral (3V0) voltage, this setting shall be set to “V0”. The method is
still exact, as the fault locator would combine the line-to-line voltage measurements with the neutral voltage measurement
to re-create the line-to-ground voltages. See the ACTUAL VALUES  RECORDS  FAULT REPORTS menu for additional
details. It required to configure the delta and neutral voltages under the source indicated as input for the fault report. Also,
the relay will check if the auxiliary signal configured is marked as “Vn” by the user (under VT setup), and inhibit the fault
location if the auxiliary signal is labeled differently.
If the broken-delta neutral voltage is not available to the relay, an approximation is possible by assuming the missing zero-
sequence voltage to be an inverted voltage drop produced by the zero-sequence current and the user-specified equivalent
zero-sequence system impedance behind the relay: V0 = –Z0  I0. In order to enable this mode of operation, the FAULT
REPORT 1 VT SUBSTITUTION setting shall be set to “I0”.
The FAULT REP 1 SYSTEM Z0 MAG and FAULT REP 1 SYSTEM Z0 ANGLE settings are used only when the VT SUBSTITUTION set-
ting value is “I0”. The magnitude is to be entered in secondary ohms. This impedance is an average system equivalent
behind the relay. It can be calculated as zero-sequence Thevenin impedance at the local bus with the protected line/feeder

disconnected. The method is accurate only if this setting matches perfectly the actual system impedance during the fault. If
the system exhibits too much variability, this approach is questionable and the fault location results for single-line-to-ground
faults shall be trusted with accordingly. It should be kept in mind that grounding points in vicinity of the installation impact
the system zero-sequence impedance (grounded loads, reactors, zig-zag transformers, shunt capacitor banks, etc.).
5.2.8 OSCILLOGRAPHY
a) MAIN MENU
PATH: SETTINGS  PRODUCT SETUP  OSCILLOGRAPHY
 OSCILLOGRAPHY NUMBER OF RECORDS: Range: 1 to 64 in steps of 1

 5
TRIGGER MODE: Range: Automatic Overwrite, Protected
MESSAGE
Automatic Overwrite
TRIGGER POSITION: Range: 0 to 100% in steps of 1
MESSAGE
50%
TRIGGER SOURCE: Range: FlexLogic operand
MESSAGE
Off
AC INPUT WAVEFORMS: Range: Off; 8, 16, 32, 64 samples/cycle
MESSAGE
16 samples/cycle
 DIGITAL CHANNELS
MESSAGE

5 MESSAGE
 ANALOG CHANNELS

Oscillography records contain waveforms captured at the sampling rate as well as other relay data at the point of trigger.
Oscillography records are triggered by a programmable FlexLogic operand. Multiple oscillography records may be captured
simultaneously.
The NUMBER OF RECORDS is selectable, but the number of cycles captured in a single record varies considerably based on
other factors such as sample rate and the number of operational modules. There is a fixed amount of data storage for oscil-
lography; the more data captured, the less the number of cycles captured per record. See the ACTUAL VALUES 
RECORDS  OSCILLOGRAPHY menu to view the number of cycles captured per record. The following table provides sam-
ple configurations with corresponding cycles/record. The minimum number of oscillographic records is three.
Table 5–6: OSCILLOGRAPHY CYCLES/RECORD EXAMPLE

RECORDS CT/VTS SAMPLE DIGITALS ANALOGS CYCLES/
RATE RECORD
3 1 8 0 0 14663
3 1 16 16 0 6945
8 1 16 16 0 3472
8 1 16 16 4 2868
8 2 16 16 4 1691
8 2 16 63 16 1221
8 2 32 63 16 749
8 2 64 63 16 422
32 2 64 63 16 124
A new record may automatically overwrite an older record if TRIGGER MODE is set to “Automatic Overwrite”.
Set the TRIGGER POSITION to a percentage of the total buffer size (for example, 10%, 50%, 75%, etc.). A trigger position of
25% consists of 25% pre- and 75% post-trigger data. The TRIGGER SOURCE is always captured in oscillography and may be
any FlexLogic parameter (element state, contact input, virtual output, etc.). The relay sampling rate is 64 samples per cycle.

The AC INPUT WAVEFORMS setting determines the sampling rate at which AC input signals (that is, current and voltage) are
stored. Reducing the sampling rate allows longer records to be stored. This setting has no effect on the internal sampling
rate of the relay which is always 64 samples per cycle; that is, it has no effect on the fundamental calculations of the device.
When changes are made to the oscillography settings, all existing oscillography records will be CLEARED.
NOTE
b) DIGITAL CHANNELS
PATH: SETTINGS  PRODUCT SETUP  OSCILLOGRAPHY  DIGITAL CHANNELS
 DIGITAL CHANNELS DIGITAL CHANNEL 1: Range: FlexLogic operand

 Off
DIGITAL CHANNEL 2: Range: FlexLogic operand
MESSAGE
Off
MESSAGE
Off


MESSAGE
Off
A DIGITAL 1(63) CHANNEL setting selects the FlexLogic operand state recorded in an oscillography trace. The length of each
oscillography trace depends in part on the number of parameters selected here. Parameters set to “Off” are ignored. Upon
startup, the relay will automatically prepare the parameter list.
c) ANALOG CHANNELS 5
PATH: SETTINGS  PRODUCT SETUP  OSCILLOGRAPHY  ANALOG CHANNELS
 ANALOG CHANNELS ANALOG CHANNEL 1: Range: Off, any FlexAnalog parameter

 Off See Appendix A for complete list.
ANALOG CHANNEL 2: Range: Off, any FlexAnalog parameter

MESSAGE See Appendix A for complete list.
Off
Off


Off
These settings select the metering actual value recorded in an oscillography trace. The length of each oscillography trace
depends in part on the number of parameters selected here. Parameters set to “Off” are ignored. The parameters available
in a given relay are dependent on:
• The type of relay,
• The type and number of CT/VT hardware modules installed, and
• The type and number of analog input hardware modules installed.
Upon startup, the relay will automatically prepare the parameter list. A list of all possible analog metering actual value
parameters is presented in Appendix A: FlexAnalog parameters. The parameter index number shown in any of the tables is
used to expedite the selection of the parameter on the relay display. It can be quite time-consuming to scan through the list
of parameters via the relay keypad and display - entering this number via the relay keypad will cause the corresponding
parameter to be displayed.
All eight CT/VT module channels are stored in the oscillography file. The CT/VT module channels are named as follows:
<slot_letter><terminal_number>—<I or V><phase A, B, or C, or 4th input>

The fourth current input in a bank is called IG, and the fourth voltage input in a bank is called VX. For example, F2-IB desig-
nates the IB signal on terminal 2 of the CT/VT module in slot F.
If there are no CT/VT modules and analog input modules, no analog traces will appear in the file; only the digital traces will
appear.
5.2.9 DATA LOGGER
PATH: SETTINGS  PRODUCT SETUP  DATA LOGGER
 DATA LOGGER DATA LOGGER MODE: Range: Continuous, Trigger

 Continuous
DATA LOGGER TRIGGER: Range: FlexLogic operand
MESSAGE
Off
DATA LOGGER RATE: Range: 15 to 3600000 ms in steps of 1
MESSAGE
60000 ms
DATA LOGGER CHNL 1: Range: Off, any FlexAnalog parameter. See Appendix A:
MESSAGE FlexAnalog Parameters for complete list.
Off
Off
Off

5 DATA LOGGER CHNL 16: Range: Off, any FlexAnalog parameter. See Appendix A:
Off
DATA LOGGER CONFIG: Range: Not applicable - shows computed data only
MESSAGE
0 CHNL x 0.0 DAYS
The data logger samples and records up to 16 analog parameters at a user-defined sampling rate. This recorded data may
be downloaded to EnerVista UR Setup and displayed with parameters on the vertical axis and time on the horizontal axis.
All data is stored in non-volatile memory, meaning that the information is retained when power to the relay is lost.
For a fixed sampling rate, the data logger can be configured with a few channels over a long period or a larger number of
channels for a shorter period. The relay automatically partitions the available memory between the channels in use. Exam-
ple storage capacities for a system frequency of 60 Hz are shown in the following table.

Table 5–7: DATA LOGGER STORAGE CAPACITY EXAMPLE

SAMPLING RATE CHANNELS DAYS STORAGE CAPACITY
15 ms 1 0.1 954 s
8 0.1 120 s
9 0.1 107 s
16 0.1 60 s
1000 ms 1 0.7 65457 s
8 0.1 8182 s
9 0.1 7273 s
16 0.1 4091 s
60000 ms 1 45.4 3927420 s
8 5.6 490920 s
9 5 436380 s
16 2.8 254460 s
3600000 ms 1 2727.5 235645200 s
8 340.9 29455200 s
9 303 26182800 s
Changing any setting affecting data logger operation will clear any data that is currently in the log.
NOTE
• DATA LOGGER MODE: This setting configures the mode in which the data logger will operate. When set to “Continu-
ous”, the data logger will actively record any configured channels at the rate as defined by the DATA LOGGER RATE. The
5
data logger will be idle in this mode if no channels are configured. When set to “Trigger”, the data logger will begin to
record any configured channels at the instance of the rising edge of the DATA LOGGER TRIGGER source FlexLogic oper-
and. The data logger will ignore all subsequent triggers and will continue to record data until the active record is full.
Once the data logger is full a CLEAR DATA LOGGER command is required to clear the data logger record before a new
record can be started. Performing the CLEAR DATA LOGGER command will also stop the current record and reset the
data logger to be ready for the next trigger.
• DATA LOGGER TRIGGER: This setting selects the signal used to trigger the start of a new data logger record. Any
FlexLogic operand can be used as the trigger source. The DATA LOGGER TRIGGER setting only applies when the mode
is set to “Trigger”.
• DATA LOGGER RATE: This setting selects the time interval at which the actual value data will be recorded.
• DATA LOGGER CHNL 1(16): This setting selects the metering actual value that is to be recorded in Channel 1(16) of
the data log. The parameters available in a given relay are dependent on: the type of relay, the type and number of CT/
VT hardware modules installed, and the type and number of Analog Input hardware modules installed. Upon startup,
the relay will automatically prepare the parameter list. A list of all possible analog metering actual value parameters is
shown in Appendix A: FlexAnalog Parameters. The parameter index number shown in any of the tables is used to
expedite the selection of the parameter on the relay display. It can be quite time-consuming to scan through the list of
parameters via the relay keypad/display – entering this number via the relay keypad will cause the corresponding
parameter to be displayed.
• DATA LOGGER CONFIG: This display presents the total amount of time the Data Logger can record the channels not
selected to “Off” without over-writing old data.

5.2.10 USER-PROGRAMMABLE LEDS
a) MAIN MENU
PATH: SETTINGS  PRODUCT SETUP  USER-PROGRAMMABLE LEDS
 USER-PROGRAMMABLE  LED TEST

See below
 LEDS 
 TRIP & ALARM LEDS

 LED1
MESSAGE
 LED2

MESSAGE
 LED48
The 48 amber LEDs on relay panels 2 and 3 can be customized to illuminate when a selected FlexLogic operand is in the
logic 1 state. The trip and alarm LEDs on panel 1 can also be customized in a similar manner. To ensure correct functional-
ity of all LEDs, an LED test feature is also provided.
b) LED TEST
5 PATH: SETTINGS  PRODUCT SETUP  USER-PROGRAMMABLE LEDS  LED TEST
 LED TEST LED TEST FUNCTION: Range: Disabled, Enabled.

 Disabled
LED TEST CONTROL: Range: FlexLogic operand
MESSAGE
Off
When enabled, the LED test can be initiated from any digital input or user-programmable condition such as user-program-
mable pushbutton. The control operand is configured under the LED TEST CONTROL setting. The test covers all LEDs,
including the LEDs of the optional user-programmable pushbuttons.
The test consists of three stages.
1. All 62 LEDs on the relay are illuminated. This is a quick test to verify if any of the LEDs is “burned”. This stage lasts as
long as the control input is on, up to a maximum of 1 minute. After 1 minute, the test will end.
2. All the LEDs are turned off, and then one LED at a time turns on for 1 second, then back off. The test routine starts at
the top left panel, moving from the top to bottom of each LED column. This test checks for hardware failures that lead
to more than one LED being turned on from a single logic point. This stage can be interrupted at any time.
3. All the LEDs are turned on. One LED at a time turns off for 1 second, then back on. The test routine starts at the top left
panel moving from top to bottom of each column of the LEDs. This test checks for hardware failures that lead to more
than one LED being turned off from a single logic point. This stage can be interrupted at any time.
When testing is in progress, the LEDs are controlled by the test sequence, rather than the protection, control, and monitor-
ing features. However, the LED control mechanism accepts all the changes to LED states generated by the relay and
stores the actual LED states (on or off) in memory. When the test completes, the LEDs reflect the actual state resulting from
relay response during testing. The reset pushbutton will not clear any targets when the LED Test is in progress.
A dedicated FlexLogic operand, LED TEST IN PROGRESS, is set for the duration of the test. When the test sequence is initi-
ated, the LED TEST INITIATED event is stored in the event recorder.
The entire test procedure is user-controlled. In particular, stage 1 can last as long as necessary, and stages 2 and 3 can be
interrupted. The test responds to the position and rising edges of the control input defined by the LED TEST CONTROL set-
ting. The control pulses must last at least 250 ms to take effect. The following diagram explains how the test is executed.

READY TO TEST
Reset the
LED TEST IN PROGRESS
rising edge of the
operand
control input
Start the software image of Restore the LED states

the LEDs from the software image
Set the
LED TEST IN PROGRESS
operand
control input is on
STAGE 1 time-out
(all LEDs on) (1 minute)
dropping edge of the

control input
rising edge of the

Wait 1 second
control input
STAGE 2 rising edge of the

(one LED on at a time) control input
rising edge of the

Wait 1 second
5
control input
rising edge
STAGE 3
of the control
(one LED off at a time) input
842011A1.CDR
Figure 5–9: LED TEST SEQUENCE

APPLICATION EXAMPLE 1:
Assume one needs to check if any of the LEDs is “burned” through user-programmable pushbutton 1. The following set-
tings should be applied. Configure user-programmable pushbutton 1 by making the following entries in the SETTINGS 
PRODUCT SETUP  USER-PROGRAMMABLE PUSHBUTTONS  USER PUSHBUTTON 1 menu:

PUSHBTN 1 DROP-OUT TIME: “0.10 s”
Configure the LED test to recognize user-programmable pushbutton 1 by making the following entries in the SETTINGS 
PRODUCT SETUP  USER-PROGRAMMABLE LEDS  LED TEST menu:
LED TEST FUNCTION: “Enabled”

LED TEST CONTROL: “PUSHBUTTON 1 ON”
The test will be initiated when the user-programmable pushbutton 1 is pressed. The pushbutton should remain pressed for
as long as the LEDs are being visually inspected. When finished, the pushbutton should be released. The relay will then
automatically start stage 2. At this point forward, test may be aborted by pressing the pushbutton.
APPLICATION EXAMPLE 2:
Assume one needs to check if any LEDs are “burned” as well as exercise one LED at a time to check for other failures. This
is to be performed via user-programmable pushbutton 1.
After applying the settings in application example 1, hold down the pushbutton as long as necessary to test all LEDs. Next,
release the pushbutton to automatically start stage 2. Once stage 2 has started, the pushbutton can be released. When
stage 2 is completed, stage 3 will automatically start. The test may be aborted at any time by pressing the pushbutton.

c) TRIP AND ALARM LEDS

PATH: SETTINGS  PRODUCT SETUP  USER-PROGRAMMABLE LEDS  TRIP & ALARM LEDS
 TRIP & ALARM LEDS TRIP LED INPUT: Range: FlexLogic operand
 Off
ALARM LED INPUT: Range: FlexLogic operand
MESSAGE
Off
The trip and alarm LEDs are in the first LED column (enhanced faceplate) and on LED panel 1 (standard faceplate). Each
indicator can be programmed to become illuminated when the selected FlexLogic operand is in the logic 1 state.
d) USER-PROGRAMMABLE LED 1(48)

PATH: SETTINGS  PRODUCT SETUP  USER-PROGRAMMABLE LEDS  USER-PROGRAMMABLE LED 1(48)
 USER-PROGRAMMABLE LED 1 OPERAND: Range: FlexLogic operand

 LED 1 Off
LED 1 TYPE: Range: Self-Reset, Latched
MESSAGE
Self-Reset
There are 48 amber LEDs across the relay faceplate LED panels. Each of these indicators can be programmed to illumi-
nate when the selected FlexLogic operand is in the logic 1 state.
For the standard faceplate, the LEDs are located as follows.
• LED Panel 2: user-programmable LEDs 1 through 24
5 • LED Panel 3: user programmable LEDs 25 through 48

For the enhanced faceplate, the LEDs are located as follows.
• LED column 2: user-programmable LEDs 1 through 12
Refer to the LED indicators section in chapter 4 for additional information on the location of these indexed LEDs.
The user-programmable LED settings select the FlexLogic operands that control the LEDs. If the LED 1 TYPE setting is “Self-
Reset” (the default setting), the LED illumination will track the state of the selected LED operand. If the LED 1 TYPE setting is
“Latched”, the LED, once lit, remains so until reset by the faceplate RESET button, from a remote device via a communica-
tions channel, or from any programmed operand, even if the LED operand state de-asserts.
Table 5–8: RECOMMENDED SETTINGS FOR USER-PROGRAMMABLE LEDS

SETTING PARAMETER SETTING PARAMETER
LED 1 operand SETTING GROUP ACT 1 LED 13 operand Off
LED 2 operand SETTING GROUP ACT 2 LED 14 operand BREAKER 2 OPEN
LED 3 operand SETTING GROUP ACT 3 LED 15 operand BREAKER 2 CLOSED
LED 4 operand SETTING GROUP ACT 4 LED 16 operand BREAKER 2 TROUBLE
LED 5 operand SETTING GROUP ACT 5 LED 17 operand SYNC 1 SYNC OP
LED 6 operand SETTING GROUP ACT 6 LED 18 operand SYNC 2 SYNC OP
LED 7 operand Off LED 19 operand Off
LED 8 operand Off LED 20 operand Off
LED 9 operand BREAKER 1 OPEN LED 21 operand AR ENABLED
LED 10 operand BREAKER 1 CLOSED LED 22 operand AR DISABLED
LED 11 operand BREAKER 1 TROUBLE LED 23 operand AR RIP
LED 12 operand Off LED 24 operand AR LO

Refer to the Control of setting groups example in the Control elements section of this chapter for group activation.
5.2.11 USER-PROGRAMMABLE SELF-TESTS
For user-programmable self-tests for CyberSentry, use the Setup > Security > Supervisory menu instead.
PATH: SETTINGS  PRODUCT SETUP  USER-PROGRAMMABLE SELF TESTS
 USER-PROGRAMMABLE DIRECT RING BREAK Range: Disabled, Enabled. Valid for units equipped with
 SELF TESTS FUNCTION: Enabled Direct Input/Output module.
DIRECT DEVICE OFF Range: Disabled, Enabled. Valid for units equipped with
MESSAGE Direct Input/Output module.
FUNCTION: Enabled
REMOTE DEVICE OFF Range: Disabled, Enabled.
MESSAGE
FUNCTION: Enabled
FIRST ETHERNET FAIL Range: Disabled, Enabled.
MESSAGE
FUNCTION: Disabled
SEC. ETHERNET FAIL Range: Disabled, Enabled.
MESSAGE
FUNCTION: Disabled
THIRD ETHERNET FAIL Range: Disabled, Enabled.
MESSAGE
FUNCTION: Disabled
BATTERY FAIL Range: Disabled, Enabled.
MESSAGE
FUNCTION: Enabled
MESSAGE
SNTP FAIL
FUNCTION: Enabled
Range: Disabled, Enabled.
5
IRIG-B FAIL Range: Disabled, Enabled.
MESSAGE
FUNCTION: Enabled
PTP FAIL Range: Disabled, Enabled.
MESSAGE
FUNCTION: Enabled
SFP MODULE FAIL Range: Disabled, Enabled.
MESSAGE
FUNCTION: Disabled
All major self-test alarms are reported automatically with their corresponding FlexLogic operands, events, and targets. Most
of the minor alarms can be disabled if desired.
When in the “Disabled” mode, minor alarms will not assert a FlexLogic operand, write to the event recorder, or display tar-
get messages. Moreover, they will not trigger the ANY MINOR ALARM or ANY SELF-TEST messages. When in the “Enabled”
mode, minor alarms continue to function along with other major and minor alarms. Refer to the Relay self-tests section in
chapter 7 for additional information on major and minor self-test alarms.
5.2.12 CONTROL PUSHBUTTONS
PATH: SETTINGS  PRODUCT SETUP  CONTROL PUSHBUTTONS  CONTROL PUSHBUTTON 1(7)
 CONTROL CONTROL PUSHBUTTON 1 Range: Disabled, Enabled

 PUSHBUTTON 1 FUNCTION: Disabled
CONTROL PUSHBUTTON 1 Range: Disabled, Enabled
MESSAGE
EVENTS: Disabled
There are three standard control pushbuttons, labeled USER 1, USER 2, and USER 3, on the standard and enhanced front
panels. These are user-programmable and can be used for various applications such as performing an LED test, switching
setting groups, and invoking and scrolling though user-programmable displays.

Firmware revisions 3.2x and older use these three pushbuttons for manual breaker control. This functionality has been
retained – if the breaker control feature is configured to use the three pushbuttons, they cannot be used as user-program-
mable control pushbuttons.
The location of the control pushbuttons are shown in the following figures.
Control pushbuttons
842813A1.CDR
Figure 5–10: CONTROL PUSHBUTTONS (ENHANCED FACEPLATE)

An additional four control pushbuttons are included on the standard faceplate when the D60 is ordered with the twelve
user-programmable pushbutton option.
STATUS EVENT CAUSE

IN SERVICE VOLTAGE
TROUBLE CURRENT RESET
TEST MODE FREQUENCY
TRIP OTHER USER 1 THREE
ALARM PHASE A STANDARD
PICKUP PHASE B USER 2
PHASE C
CONTROL
NEUTRAL/GROUND USER 3 PUSHBUTTONS
5
USER 4
USER 5 FOUR EXTRA

OPTIONAL
USER 6
CONTROL
USER 7 PUSHBUTTONS
842733A2.CDR
Figure 5–11: CONTROL PUSHBUTTONS (STANDARD FACEPLATE)

Control pushbuttons are not typically used for critical operations and are not protected by the control password. However,
by supervising their output operands, the user can dynamically enable or disable control pushbuttons for security reasons.
Each control pushbutton asserts its own FlexLogic operand. These operands should be configured appropriately to perform
the desired function. The operand remains asserted as long as the pushbutton is pressed and resets when the pushbutton
is released. A dropout delay of 100 ms is incorporated to ensure fast pushbutton manipulation will be recognized by various
features that may use control pushbuttons as inputs.
An event is logged in the event record (as per user setting) when a control pushbutton is pressed. No event is logged when
the pushbutton is released. The faceplate keys (including control keys) cannot be operated simultaneously – a given key
must be released before the next one can be pressed.
The control pushbuttons become user-programmable only if the breaker control feature is not configured for manual control
via the USER 1 through 3 pushbuttons as shown below. If configured for manual control, breaker control typically uses the
larger, optional user-programmable pushbuttons, making the control pushbuttons available for other user applications.

SETTING
CONTROL PUSHBUTTON
{
1 FUNCTION:
Enabled=1
SETTINGS
SYSTEM SETUP/
BREAKERS/BREAKER 1/
BREAKER 1 PUSHBUTTON
CONTROL:
When applicable
AND RUN
Enabled=1
OFF TIMER
SYSTEM SETUP/ FLEXLOGIC OPERAND
BREAKERS/BREAKER 2/ ON 0 CONTROL PUSHBTN 1 ON
BREAKER 2 PUSHBUTTON 100 msec
CONTROL:
842010A2.CDR
Enabled=1
Figure 5–12: CONTROL PUSHBUTTON LOGIC
5.2.13 USER-PROGRAMMABLE PUSHBUTTONS
PATH: SETTINGS  PRODUCT SETUP  USER-PROGRAMMABLE PUSHBUTTONS  USER PUSHBUTTON 1(16)
 USER PUSHBUTTON 1 PUSHBUTTON 1 Range: Self-Reset, Latched, Disabled

 FUNCTION: Disabled
PUSHBTN 1 ID TEXT: Range: Up to 20 alphanumeric characters
MESSAGE
PUSHBTN 1 ON TEXT: Range: Up to 20 alphanumeric characters

MESSAGE
Range: Up to 20 alphanumeric characters

5
PUSHBTN 1 OFF TEXT:
MESSAGE
PUSHBTN 1 HOLD: Range: 0.0 to 10.0 s in steps of 0.1

MESSAGE
0.0 s
PUSHBTN 1 SET: Range: FlexLogic operand
MESSAGE
Off
PUSHBTN 1 RESET: Range: FlexLogic operand
MESSAGE
Off
PUSHBTN 1 AUTORST: Range: Disabled, Enabled
MESSAGE
Disabled
PUSHBTN 1 AUTORST Range: 0.2 to 600.0 s in steps of 0.1
MESSAGE
DELAY: 1.0 s
PUSHBTN 1 REMOTE: Range: FlexLogic operand
MESSAGE
Off
PUSHBTN 1 LOCAL: Range: FlexLogic operand
MESSAGE
Off
PUSHBTN 1 DROP-OUT Range: 0 to 60.00 s in steps of 0.05
MESSAGE
TIME: 0.00 s
PUSHBTN 1 LED CTL: Range: FlexLogic operand
MESSAGE
Off
PUSHBTN 1 MESSAGE: Range: Disabled, Normal, High Priority
MESSAGE
Disabled
PUSHBUTTON 1 Range: Disabled, Enabled
MESSAGE
EVENTS: Disabled

The optional user-programmable pushbuttons (specified in the order code) provide an easy and error-free method of enter-
ing digital state (on, off) information. The number of available pushbuttons is dependent on the faceplate module ordered
with the relay.
• Type P faceplate: standard horizontal faceplate with 12 user-programmable pushbuttons.
• Type Q faceplate: enhanced horizontal faceplate with 16 user-programmable pushbuttons.
The digital state can be entered locally (by directly pressing the front panel pushbutton) or remotely (via FlexLogic oper-
ands) into FlexLogic equations, protection elements, and control elements. Typical applications include breaker control,
autorecloser blocking, and setting groups changes. The user-programmable pushbuttons are under the control level of
password protection.
The user-configurable pushbuttons for the enhanced faceplate are shown below.
USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER
LABEL 1 LABEL 2 LABEL 3 LABEL 4 LABEL 5 LABEL 6 LABEL 7 LABEL 8 LABEL 9 LABEL 10 LABEL 11 LABEL 12 LABEL 13 LABEL 14 LABEL 15 LABEL 16
842814A1.CDR
Figure 5–13: USER-PROGRAMMABLE PUSHBUTTONS (ENHANCED FACEPLATE)

The user-configurable pushbuttons for the standard faceplate are shown below.
5 1
USER LABEL
3
USER LABEL
5
USER LABEL
7
USER LABEL
9
USER LABEL
11
USER LABEL
2 4 6 8 10 12
USER LABEL USER LABEL USER LABEL USER LABEL USER LABEL USER LABEL
842779A1.CDR
Figure 5–14: USER-PROGRAMMABLE PUSHBUTTONS (STANDARD FACEPLATE)

Both the standard and enhanced faceplate pushbuttons can be custom labeled with a factory-provided template, available
online at http://www.gedigitalenergy.com/multilin. The EnerVista UR Setup software can also be used to create labels for
the enhanced faceplate.
Each pushbutton asserts its own “On” and “Off” FlexLogic operands (for example, PUSHBUTTON 1 ON and PUSHBUTTON 1
OFF). These operands are available for each pushbutton and are used to program specific actions. If any pushbutton is
active, the ANY PB ON operand will be asserted.
Each pushbutton has an associated LED indicator. By default, this indicator displays the present status of the correspond-
ing pushbutton (on or off). However, each LED indicator can be assigned to any FlexLogic operand through the PUSHBTN 1
LED CTL setting.
The pushbuttons can be automatically controlled by activating the operands assigned to the PUSHBTN 1 SET (for latched and
self-reset mode) and PUSHBTN 1 RESET (for latched mode only) settings. The pushbutton reset status is declared when the
PUSHBUTTON 1 OFF operand is asserted. The activation and deactivation of user-programmable pushbuttons is dependent
on whether latched or self-reset mode is programmed.
• Latched mode: In latched mode, a pushbutton can be set (activated) by asserting the operand assigned to the PUSH-
BTN 1 SET setting or by directly pressing the associated front panel pushbutton. The pushbutton maintains the set state
until deactivated by the reset command or after a user-specified time delay. The state of each pushbutton is stored in
non-volatile memory and maintained through a loss of control power.
The pushbutton is reset (deactivated) in latched mode by asserting the operand assigned to the PUSHBTN 1 RESET set-
ting or by directly pressing the associated active front panel pushbutton.

It can also be programmed to reset automatically through the PUSHBTN 1 AUTORST and PUSHBTN 1 AUTORST DELAY set-
tings. These settings enable the autoreset timer and specify the associated time delay. The autoreset timer can be
used in select-before-operate (SBO) breaker control applications, where the command type (close/open) or breaker
location (feeder number) must be selected prior to command execution. The selection must reset automatically if con-
trol is not executed within a specified time period.
• Self-reset mode: In self-reset mode, a pushbutton will remain active for the time it is pressed (the pulse duration) plus
the dropout time specified in the PUSHBTN 1 DROP-OUT TIME setting. If the pushbutton is activated via FlexLogic, the
pulse duration is specified by the PUSHBTN 1 DROP-OUT TIME only. The time the operand remains assigned to the PUSH-
BTN 1 SET setting has no effect on the pulse duration.
The pushbutton is reset (deactivated) in self-reset mode when the dropout delay specified in the PUSHBTN 1 DROP-OUT
TIMEsetting expires.
The pulse duration of the remote set, remote reset, or local pushbutton must be at least 50 ms to operate the push-
button. This allows the user-programmable pushbuttons to properly operate during power cycling events and vari-
NOTE ous system disturbances that may cause transient assertion of the operating signals.
The local and remote operation of each user-programmable pushbutton can be inhibited through the PUSHBTN 1 LOCAL and
PUSHBTN 1 REMOTE settings, respectively. If local locking is applied, the pushbutton will ignore set and reset commands
executed through the front panel pushbuttons. If remote locking is applied, the pushbutton will ignore set and reset com-
mands executed through FlexLogic operands.
The locking functions are not applied to the autorestart feature. In this case, the inhibit function can be used in SBO control
operations to prevent the pushbutton function from being activated and ensuring “one-at-a-time” select operation.
The locking functions can also be used to prevent the accidental pressing of the front panel pushbuttons. The separate
inhibit of the local and remote operation simplifies the implementation of local/remote control supervision.
Pushbutton states can be logged by the event recorder and displayed as target messages. In latched mode, user-defined
messages can also be associated with each pushbutton and displayed when the pushbutton is on or changing to off. 5
• PUSHBUTTON 1 FUNCTION: This setting selects the characteristic of the pushbutton. If set to “Disabled”, the push-
button is not active and the corresponding FlexLogic operands (both “On” and “Off”) are de-asserted. If set to “Self-
Reset”, the control logic is activated by the pulse (longer than 100 ms) issued when the pushbutton is being physically
pressed or virtually pressed via a FlexLogic operand assigned to the PUSHBTN 1 SET setting.
When in “Self-Reset” mode and activated locally, the pushbutton control logic asserts the “On” corresponding Flex-
Logic operand as long as the pushbutton is being physically pressed, and after being released the deactivation of the
operand is delayed by the drop out timer. The “Off” operand is asserted when the pushbutton element is deactivated. If
the pushbutton is activated remotely, the control logic of the pushbutton asserts the corresponding “On” FlexLogic
operand only for the time period specified by the PUSHBTN 1 DROP-OUT TIME setting.
If set to “Latched”, the control logic alternates the state of the corresponding FlexLogic operand between “On” and “Off”
on each button press or by virtually activating the pushbutton (assigning set and reset operands). When in the
“Latched” mode, the states of the FlexLogic operands are stored in a non-volatile memory. Should the power supply be
lost, the correct state of the pushbutton is retained upon subsequent power up of the relay.
• PUSHBTN 1 ID TEXT: This setting specifies the top 20-character line of the user-programmable message and is
intended to provide ID information of the pushbutton. Refer to the User-definable displays section for instructions on
how to enter alphanumeric characters from the keypad.
• PUSHBTN 1 ON TEXT: This setting specifies the bottom 20-character line of the user-programmable message and is
displayed when the pushbutton is in the “on” position. Refer to the User-definable displays section for instructions on
entering alphanumeric characters from the keypad.
• PUSHBTN 1 OFF TEXT: This setting specifies the bottom 20-character line of the user-programmable message and is
displayed when the pushbutton is activated from the on to the off position and the PUSHBUTTON 1 FUNCTION is
“Latched”. This message is not displayed when the PUSHBUTTON 1 FUNCTION is “Self-reset” as the pushbutton operand
status is implied to be “Off” upon its release. The length of the “Off” message is configured with the PRODUCT SETUP
 DISPLAY PROPERTIES  FLASH MESSAGE TIME setting.
• PUSHBTN 1 HOLD: This setting specifies the time required for a pushbutton to be pressed before it is deemed active.
This timer is reset upon release of the pushbutton. Note that any pushbutton operation will require the pushbutton to be
pressed a minimum of 50 ms. This minimum time is required prior to activating the pushbutton hold timer.

• PUSHBTN 1 SET: This setting assigns the FlexLogic operand serving to operate the pushbutton element and to assert
PUSHBUTTON 1 ON operand. The duration of the incoming set signal must be at least 100 ms.
• PUSHBTN 1 RESET: This setting assigns the FlexLogic operand serving to reset pushbutton element and to assert
PUSHBUTTON 1 OFF operand. This setting is applicable only if pushbutton is in latched mode. The duration of the
incoming reset signal must be at least 50 ms.
• PUSHBTN 1 AUTORST: This setting enables the user-programmable pushbutton autoreset feature. This setting is
applicable only if the pushbutton is in the “Latched” mode.
• PUSHBTN 1 AUTORST DELAY: This setting specifies the time delay for automatic reset of the pushbutton when in
the latched mode.
• PUSHBTN 1 REMOTE: This setting assigns the FlexLogic operand serving to inhibit pushbutton operation from the
operand assigned to the PUSHBTN 1 SET or PUSHBTN 1 RESET settings.
• PUSHBTN 1 LOCAL: This setting assigns the FlexLogic operand serving to inhibit pushbutton operation from the front
panel pushbuttons. This locking functionality is not applicable to pushbutton autoreset.
• PUSHBTN 1 DROP-OUT TIME: This setting applies only to “Self-Reset” mode and specifies the duration of the push-
button active status after the pushbutton has been released. When activated remotely, this setting specifies the entire
activation time of the pushbutton status; the length of time the operand remains on has no effect on the pulse duration.
This setting is required to set the duration of the pushbutton operating pulse.
• PUSHBTN 1 LED CTL: This setting assigns the FlexLogic operand serving to drive pushbutton LED. If this setting is
“Off”, then LED operation is directly linked to PUSHBUTTON 1 ON operand.
• PUSHBTN 1 MESSAGE: If pushbutton message is set to “High Priority”, the message programmed in the PUSHBTN 1
IDand PUSHBTN 1 ON TEXT settings will be displayed undisturbed as long as PUSHBUTTON 1 ON operand is asserted.
The high priority option is not applicable to the PUSHBTN 1 OFF TEXT setting.
5 This message can be temporary removed if any front panel keypad button is pressed. However, ten seconds of keypad
inactivity will restore the message if the PUSHBUTTON 1 ON operand is still active.
If the PUSHBTN 1 MESSAGE is set to “Normal”, the message programmed in the PUSHBTN 1 ID and PUSHBTN 1 ON TEXT
settings will be displayed as long as PUSHBUTTON 1 ON operand is asserted, but not longer than time period specified
by FLASH MESSAGE TIME setting. After the flash time is expired, the default message or other active target message is
displayed. The instantaneous reset of the flash message will be executed if any relay front panel button is pressed or
any new target or message becomes active.
The PUSHBTN 1 OFF TEXT setting is linked to PUSHBUTTON 1 OFF operand and will be displayed in conjunction with
PUSHBTN 1 ID only if pushbutton element is in the “Latched” mode. The PUSHBTN 1 OFF TEXT message will be displayed
as “Normal” if the PUSHBTN 1 MESSAGE setting is “High Priority” or “Normal”.
• PUSHBUTTON 1 EVENTS: If this setting is enabled, each pushbutton state change will be logged as an event into
event recorder.

The user-programmable pushbutton logic is shown below.

TIMER
FLEXLOGIC OPERAND 200 ms
PUSHBUTTON 1 OFF
0
SETTING
Function
LATCHED To user-programmable
= Enabled
pushbuttons logic
= Latched sheet 2, 842024A2
OR LATCHED/SELF-RESET
= Self-Reset
SETTING
Local Lock
Off = 0
Non-volatile latch
AND
S
TIMER
SETTING Latch
50 ms
Remote Lock R
Off = 0 AND
0
SETTING OR
TIMER
Hold 50 ms
TPKP
0
0
OR
SETTING
Set AND
Off = 0
To user-programmable
OR PUSHBUTTON ON pushbuttons logic
OR
sheet 2, 842024A2
SETTING
Reset AND
5
Off = 0
AND
SETTING
SETTING
Autoreset Delay
Autoreset Function
TPKP
= Enabled
AND
= Disabled
0
AND
SETTING
Drop-Out Timer
TIMER 0
FLEXLOGIC OPERAND 200 ms OR
TRST
PUSHBUTTON 1 ON
0
842021A3.CDR
AND
Figure 5–15: USER-PROGRAMMABLE PUSHBUTTON LOGIC (Sheet 1 of 2)

LCD MESSAGE
ENGAGE MESSAGE
SETTING
LATCHED Flash Message Time
SETTINGS
0 Top Text
AND
OR TRST = XXXXXXXXXX
On Text
= XXXXXXXXXX
Instantaneous
From user-programmable reset *
pushbuttons logic
sheet 1, 842021A3
FLEXLOGIC OPERAND
LATCHED/SELF-RESET
AND PUSHBUTTON 1 OFF
FLEXLOGIC OPERAND
PUSHBUTTON ON PUSHBUTTON 1 ON
The message is temporarily removed if

any keypad button is pressed. Ten (10)
seconds of keypad inactivity restores LCD MESSAGE
SETTING the message.
ENGAGE MESSAGE
Message Priority
AND
= Disabled
= High Priority SETTINGS
= Normal Top Text
= XXXXXXXXXX
OR
On Text
SETTING
= XXXXXXXXXX
Flash Message Time
0
AND
TRST
Instantaneous
Instantaneous reset will be executed if any reset *
front panel button is pressed or any new
5
target or message becomes active.
PUSHBUTTON 1 LED LOGIC
1. If pushbutton 1 LED control is set to off.
Pushbutton 1
FLEXLOGIC OPERAND LED
FLEXLOGIC OPERAND PUSHBUTTON 1 ON
PUSHBUTTON 1 ON
PUSHBUTTON 2 ON 2. If pushbutton 1 LED control is not set to off.
FLEXLOGIC OPERAND
PUSHBUTTON 3 ON SETTING Pushbutton 1
OR ANY PB ON
PUSHBTN 1 LED CTL LED
= any FlexLogic operand

PUSHBUTTON 16 ON
The enhanced front panel has 16 operands;
the standard front panel has 12 842024A2.CDR
Figure 5–16: USER-PROGRAMMABLE PUSHBUTTON LOGIC (Sheet 2 of 2)

User-programmable pushbuttons require a type HP or HQ faceplate. If an HP or HQ type faceplate was ordered
separately, the relay order code must be changed to indicate the correct faceplate option. This can be done via
NOTE
EnerVista UR Setup with the Maintenance > Enable Pushbutton command.
5.2.14 FLEX STATE PARAMETERS
PATH: SETTINGS  PRODUCT SETUP  FLEX STATE PARAMETERS
 FLEX STATE PARAMETER 1: Range: FlexLogic operand

 PARAMETERS Off
PARAMETER 2: Range: FlexLogic operand
MESSAGE
Off
MESSAGE
Off


MESSAGE
Off

This feature provides a mechanism where any of 256 selected FlexLogic operand states can be used for efficient monitor-
ing. The feature allows user-customized access to the FlexLogic operand states in the relay. The state bits are packed so
that 16 states may be read out in a single Modbus register. The state bits can be configured so that all of the states which
are of interest to the user are available in a minimum number of Modbus registers.
The state bits may be read out in the “Flex States” register array beginning at Modbus address 0900h. Sixteen states are
packed into each register, with the lowest-numbered state in the lowest-order bit. There are sixteen registers to accommo-
date the 256 state bits.
5.2.15 USER-DEFINABLE DISPLAYS
a) MAIN MENU
PATH: SETTINGS  PRODUCT SETUP  USER-DEFINABLE DISPLAYS
 USER-DEFINABLE INVOKE AND SCROLL: Range: FlexLogic operand

 DISPLAYS Off
 USER DISPLAY 1 Range: up to 20 alphanumeric characters
MESSAGE

MESSAGE

MESSAGE


MESSAGE
 USER DISPLAY 16

Range: up to 20 alphanumeric characters
5
This menu provides a mechanism for manually creating up to 16 user-defined information displays in a convenient viewing
sequence in the USER DISPLAYS menu (between the TARGETS and ACTUAL VALUES top-level menus). The sub-menus facili-
tate text entry and Modbus register data pointer options for defining the user display content.
Once programmed, the user-definable displays can be viewed in two ways.
• KEYPAD: Use the MENU key to select the USER DISPLAYS menu item to access the first user-definable display (note
that only the programmed screens are displayed). The screens can be scrolled using the UP and DOWN keys. The
display disappears after the default message time-out period specified by the PRODUCT SETUP  DISPLAY PROPER-
TIES  DEFAULT MESSAGE TIMEOUT setting.
• USER-PROGRAMMABLE CONTROL INPUT: The user-definable displays also respond to the INVOKE AND SCROLL
setting. Any FlexLogic operand (in particular, the user-programmable pushbutton operands), can be used to navigate
the programmed displays.
On the rising edge of the configured operand (such as when the pushbutton is pressed), the displays are invoked by
showing the last user-definable display shown during the previous activity. From this moment onward, the operand
acts exactly as the down key and allows scrolling through the configured displays. The last display wraps up to the first
one. The INVOKE AND SCROLL input and the DOWN key operate concurrently.
When the default timer expires (set by the DEFAULT MESSAGE TIMEOUT setting), the relay will start to cycle through the
user displays. The next activity of the INVOKE AND SCROLL input stops the cycling at the currently displayed user dis-
play, not at the first user-defined display. The INVOKE AND SCROLL pulses must last for at least 250 ms to take effect.

b) USER DISPLAYS 1 THROUGH 16

PATH: SETTINGS  PRODUCT SETUP  USER-DEFINABLE DISPLAYS  USER DISPLAY 1(16)
 USER DISPLAY 1 DISP 1 TOP LINE: Range: up to 20 alphanumeric characters


DISP 1 BOTTOM LINE: Range: up to 20 alphanumeric characters
MESSAGE
DISP 1 ITEM 1 Range: 0 to 65535 in steps of 1

MESSAGE
0
MESSAGE
0
MESSAGE
0
MESSAGE
0
DISP 1 ITEM 5: Range: 0 to 65535 in steps of 1
MESSAGE
0
Any existing system display can be automatically copied into an available user display by selecting the existing display and
pressing the ENTER key. The display will then prompt ADD TO USER DISPLAY LIST?. After selecting “Yes”, a message indi-
cates that the selected display has been added to the user display list. When this type of entry occurs, the sub-menus are
automatically configured with the proper content – this content may subsequently be edited.
5 This menu is used to enter user-defined text and user-selected Modbus-registered data fields into the particular user dis-
play. Each user display consists of two 20-character lines (top and bottom). The tilde (~) character is used to mark the start
of a data field – the length of the data field needs to be accounted for. Up to five separate data fields can be entered in a
user display – the nth tilde (~) refers to the nth item.
A user display may be entered from the faceplate keypad or the EnerVista UR Setup interface (preferred for convenience).
The following procedure shows how to enter text characters in the top and bottom lines from the faceplate keypad:
1. Select the line to be edited.
2. Press the decimal key to enter text edit mode.
3. Use either VALUE key to scroll through the characters. A space is selected like a character.
4. Press the decimal key to advance the cursor to the next position.
5. Repeat step 3 and continue entering characters until the desired text is displayed.
6. The HELP key may be pressed at any time for context sensitive help information.
7. Press the ENTER key to store the new settings.
To enter a numerical value for any of the five items (the decimal form of the selected Modbus address) from the faceplate
keypad, use the number keypad. Use the value of “0” for any items not being used. Use the HELP key at any selected sys-
tem display (setting, actual value, or command) which has a Modbus address, to view the hexadecimal form of the Modbus
address, then manually convert it to decimal form before entering it (EnerVista UR Setup usage conveniently facilitates this
conversion).
Use the MENU key to go to the user displays menu to view the user-defined content. The current user displays will show in
sequence, changing every four seconds. While viewing a user display, press the ENTER key and then select the ‘Yes”
option to remove the display from the user display list. Use the MENU key again to exit the user displays menu.

An example user display setup and result is shown below:
 USER DISPLAY 1 DISP 1 TOP LINE: Shows user-defined text with first tilde marker.
 Current X ~ A
DISP 1 BOTTOM LINE: Shows user-defined text with second tilde marker.
MESSAGE
Current Y ~ A
DISP 1 ITEM 1: Shows decimal form of user-selected Modbus register
MESSAGE address, corresponding to first tilde marker.
6016
DISP 1 ITEM 2: Shows decimal form of user-selected Modbus register
MESSAGE address, corresponding to second tilde marker.
6357
DISP 1 ITEM 3: This item is not being used. There is no corresponding
MESSAGE tilde marker in top or bottom lines.
0
MESSAGE tilde marker in top or bottom lines.
0
MESSAGE
0 tilde marker in top or bottom lines.
USER DISPLAYS Current X 0.850 Shows the resultant display content.


Current Y 0.327 A
If the parameters for the top line and the bottom line items have the same units, then the unit is displayed on the
bottom line only. The units are only displayed on both lines if the units specified both the top and bottom line items 5
NOTE are different.
5.2.16 DIRECT INPUTS AND OUTPUTS
a) MAIN MENU
PATH: SETTINGS  PRODUCT SETUP  DIRECT I/O
 DIRECT I/O DIRECT OUTPUT Range: 1 to 16 in steps of 1

 DEVICE ID: 1
DIRECT I/O CH1 RING Range: Yes, No
MESSAGE
CONFIGURATION: Yes
DIRECT I/O CH2 RING Range: Yes, No
MESSAGE
CONFIGURATION: Yes
DIRECT I/O DATA Range: 64 kbps, 128 kbps
MESSAGE
RATE: 64 kbps
DIRECT I/O CHANNEL Range: Disabled, Enabled
MESSAGE
CROSSOVER: Disabled
 CRC ALARM CH1

 CRC ALARM CH2

 UNRETURNED
 MESSAGES ALARM CH1
 UNRETURNED
 MESSAGES ALARM CH2

Direct inputs and outputs are intended for exchange of status information (inputs and outputs) between UR-series relays
connected directly via type 7 digital communications cards. The mechanism is very similar to IEC 61850 GSSE, except that
communications takes place over a non-switchable isolated network and is optimized for speed. On type 7 cards that sup-
port two channels, direct output messages are sent from both channels simultaneously. This effectively sends direct output
messages both ways around a ring configuration. On type 7 cards that support one channel, direct output messages are
sent only in one direction. Messages will be resent (forwarded) when it is determined that the message did not originate at
the receiver.
Direct output message timing is similar to GSSE message timing. Integrity messages (with no state changes) are sent at
least every 1000 ms. Messages with state changes are sent within the main pass scanning the inputs and asserting the
outputs unless the communication channel bandwidth has been exceeded. Two self-tests are performed and signaled by
the following FlexLogic operands:
1. DIRECT RING BREAK (direct input/output ring break). This FlexLogic operand indicates that direct output messages
sent from a UR-series relay are not being received back by the relay.
2. DIRECT DEVICE 1 OFF to DIRECT DEVICE 16 OFF (direct device offline). These FlexLogic operands indicate that direct
output messages from at least one direct device are not being received.
Direct input and output settings are similar to remote input and output settings. The equivalent of the remote device name
strings for direct inputs and outputs is the DIRECT OUTPUT DEVICE ID. The DIRECT OUTPUT DEVICE ID setting identifies the
relay in all direct output messages. All UR-series IEDs in a ring should have unique numbers assigned. The IED ID is used
to identify the sender of the direct input and output message.
If the direct input and output scheme is configured to operate in a ring (DIRECT I/O CH1 RING CONFIGURATION or DIRECT I/O
CH2 RING CONFIGURATION is “Yes”), all direct output messages should be received back. If not, the direct input/output ring
break self-test is triggered. The self-test error is signaled by the DIRECT RING BREAK FlexLogic operand.
Select the DIRECT I/O DATA RATE to match the data capabilities of the communications channel. All IEDs communicating
5 over direct inputs and outputs must be set to the same data rate. UR-series IEDs equipped with dual-channel communica-
tions cards apply the same data rate to both channels. Delivery time for direct input and output messages is approximately
0.2 of a power system cycle at 128 kbps and 0.4 of a power system cycle at 64 kbps, per each ‘bridge’.

Table 5–9: DIRECT INPUT AND OUTPUT DATA RATES

MODULE CHANNEL SUPPORTED DATA RATES
74 Channel 1 64 kbps
Channel 2 64 kbps
7L Channel 1 64 kbps, 128 kbps
Channel 2 64 kbps, 128 kbps
7M Channel 1 64 kbps, 128 kbps
7P Channel 1 64 kbps, 128 kbps
7T Channel 1 64 kbps, 128 kbps
7W Channel 1 64 kbps, 128 kbps
7V Channel 1 64 kbps, 128 kbps
2A Channel 1 64 kbps
2B Channel 1 64 kbps
Channel 2 64 kbps
2G Channel 1 128 kbps
2H Channel 1 128 kbps
77 Channel 1 64 kbps 5
Channel 2 64 kbps
Channel 2 64 kbps
7E Channel 1 64 kbps
Channel 2 64 kbps
7F Channel 1 64 kbps
Channel 2 64 kbps
7G Channel 1 64 kbps
Channel 2 64 kbps
7Q Channel 1 64 kbps
Channel 2 64 kbps
7R Channel 1 64 kbps
7S Channel 1 64 kbps
Channel 2 64 kbps
The G.703 modules are fixed at 64 kbps. The DIRECT I/O DATA RATE setting is not applicable to these modules.
NOTE
The DIRECT I/O CHANNEL CROSSOVER setting applies to D60s with dual-channel communication cards and allows crossing
over messages from channel 1 to channel 2. This places all UR-series IEDs into one direct input and output network
regardless of the physical media of the two communication channels.
The following application examples illustrate the basic concepts for direct input and output configuration. Please refer to the
Inputs and outputs section in this chapter for information on configuring FlexLogic operands (flags, bits) to be exchanged.

EXAMPLE 1: EXTENDING THE INPUT/OUTPUT CAPABILITIES OF A UR-SERIES RELAY

Consider an application that requires additional quantities of digital inputs or output contacts or lines of programmable logic
that exceed the capabilities of a single UR-series chassis. The problem is solved by adding an extra UR-series IED, such
as the C30, to satisfy the additional input and output and programmable logic requirements. The two IEDs are connected
via single-channel digital communication cards as shown in the figure below.
TX1
UR IED 1
RX1
TX1
UR IED 2
RX1
842711A1.CDR
Figure 5–17: INPUT AND OUTPUT EXTENSION VIA DIRECT INPUTS AND OUTPUTS
In the above application, the following settings should be applied. For UR-series IED 1:
DIRECT OUTPUT DEVICE ID: “1”
DIRECT I/O CH1 RING CONFIGURATION: “Yes”
DIRECT I/O DATA RATE: “128 kbps”
For UR-series IED 2:

5 DIRECT I/O CH1 RING CONFIGURATION:

DIRECT I/O DATA RATE: “128 kbps”
“Yes”
The message delivery time is about 0.2 of power cycle in both ways (at 128 kbps); that is, from device 1 to device 2, and
from device 2 to device 1. Different communications cards can be selected by the user for this back-to-back connection (for
example: fiber, G.703, or RS422).
EXAMPLE 2: INTERLOCKING BUSBAR PROTECTION
A simple interlocking busbar protection scheme could be accomplished by sending a blocking signal from downstream
devices, say 2, 3, and 4, to the upstream device that monitors a single incomer of the busbar, as shown below.
UR IED 1 BLOCK
UR IED 2 UR IED 3 UR IED 4
842712A1.CDR
Figure 5–18: SAMPLE INTERLOCKING BUSBAR PROTECTION SCHEME

For increased reliability, a dual-ring configuration (shown below) is recommended for this application.

TX1 RX1
UR IED 1
RX2 TX2
RX1 TX2 RX2 TX1

UR IED 2 UR IED 4
TX1 RX2 TX2 RX1
TX2 RX2
UR IED 3
RX1 TX1
842716A1.CDR
Figure 5–19: INTERLOCKING BUS PROTECTION SCHEME VIA DIRECT INPUTS/OUTPUTS

DIRECT I/O CH1 RING CONFIGURATION: “Yes” 5
Message delivery time is approximately 0.2 of power system cycle (at 128 kbps) times number of ‘bridges’ between the ori-
gin and destination. Dual-ring configuration effectively reduces the maximum ‘communications distance’ by a factor of two.
In this configuration the following delivery times are expected (at 128 kbps) if both rings are healthy:
IED 1 to IED 2: 0.2 of power system cycle;
IED 3 to IED 4: 0.2 of power system cycle.
If one ring is broken (say TX2-RX2) the delivery times are as follows:
A coordinating timer for this bus protection scheme could be selected to cover the worst case scenario (0.4 of a power sys-
tem cycle). Upon detecting a broken ring, the coordination time should be adaptively increased to 0.6 of a power system
cycle. The complete application requires addressing a number of issues such as failure of both the communications rings,
failure or out-of-service conditions of one of the relays, etc. Self-monitoring flags of the direct inputs and outputs feature
would be primarily used to address these concerns.

EXAMPLE 3: PILOT-AIDED SCHEMES

Consider the three-terminal line protection application shown below:
UR IED 1 UR IED 2
UR IED 3
842713A1.CDR
Figure 5–20: THREE-TERMINAL LINE APPLICATION

A permissive pilot-aided scheme could be implemented in a two-ring configuration as shown below (IEDs 1 and 2 constitute
a first ring, while IEDs 2 and 3 constitute a second ring):
TX1 RX1 RX2

UR IED 1 UR IED 2
RX1 TX1 TX2
5
RX1
UR IED 3
TX1
842714A1.CDR
Figure 5–21: SINGLE-CHANNEL OPEN LOOP CONFIGURATION

In this configuration the following delivery times are expected (at 128 kbps):
In the above scheme, IEDs 1 and 3 do not communicate directly. IED 2 must be configured to forward the messages as
explained in the Inputs and outputs section. A blocking pilot-aided scheme should be implemented with more security and,
ideally, faster message delivery time. This could be accomplished using a dual-ring configuration as shown below.

TX2 TX1 RX1 RX2

UR IED 1 UR IED 2
RX1 RX2 TX2 TX1
TX1 RX1
UR IED 3
RX2 TX2
842715A1.CDR
Figure 5–22: DUAL-CHANNEL CLOSED LOOP (DUAL-RING) CONFIGURATION

DIRECT I/O CH1 RING CONFIGURATION:
DIRECT I/O CH2 RING CONFIGURATION:
“Yes”
“Yes”
5
In this configuration the following delivery times are expected (at 128 kbps) if both the rings are healthy:
The two communications configurations could be applied to both permissive and blocking schemes. Speed, reliability and
cost should be taken into account when selecting the required architecture.
b) CRC ALARMS
PATH: SETTINGS  PRODUCT SETUP  DIRECT I/O  CRC ALARM CH1(2)
 CRC ALARM CH1 CRC ALARM CH1 Range: Enabled, Disabled

CRC ALARM CH1 Range: 100 to 10000 in steps of 1
MESSAGE
MESSAGE COUNT: 600
CRC ALARM CH1 Range: 1 to 1000 in steps of 1
MESSAGE
THRESHOLD: 10
CRC ALARM CH1 Range: Enabled, Disabled
MESSAGE
EVENTS: Disabled
The D60 checks integrity of the incoming direct input and output messages using a 32-bit CRC. The CRC alarm function is
available for monitoring the communication medium noise by tracking the rate of messages failing the CRC check. The
monitoring function counts all incoming messages, including messages that failed the CRC check. A separate counter adds
up messages that failed the CRC check. When the failed CRC counter reaches the user-defined level specified by the CRC
ALARM CH1 THRESHOLD setting within the user-defined message count CRC ALARM 1 CH1 COUNT, the DIR IO CH1 CRC ALARM
FlexLogic operand is set.
When the total message counter reaches the user-defined maximum specified by the CRC ALARM CH1 MESSAGE COUNT set-
ting, both the counters reset and the monitoring process is restarted.

The operand shall be configured to drive an output contact, user-programmable LED, or selected communication-based
output. Latching and acknowledging conditions - if required - should be programmed accordingly.
The CRC alarm function is available on a per-channel basis. The total number of direct input and output messages that
failed the CRC check is available as the ACTUAL VALUES  STATUS  DIRECT INPUTS  CRC FAIL COUNT CH1 actual
value.
• Message count and length of the monitoring window: To monitor communications integrity, the relay sends 1 message
per second (at 64 kbps) or 2 messages per second (128 kbps) even if there is no change in the direct outputs. For
example, setting the CRC ALARM CH1 MESSAGE COUNT to “10000”, corresponds a time window of about 160 minutes at
64 kbps and 80 minutes at 128 kbps. If the messages are sent faster as a result of direct outputs activity, the monitor-
ing time interval will shorten. This should be taken into account when determining the CRC ALARM CH1 MESSAGE COUNT
setting. For example, if the requirement is a maximum monitoring time interval of 10 minutes at 64 kbps, then the CRC
ALARM CH1 MESSAGE COUNT should be set to 10  60  1 = 600.
• Correlation of failed CRC and bit error rate (BER): The CRC check may fail if one or more bits in a packet are cor-
rupted. Therefore, an exact correlation between the CRC fail rate and the BER is not possible. Under certain assump-
tions an approximation can be made as follows. A direct input and output packet containing 20 bytes results in 160 bits
of data being sent and therefore, a transmission of 63 packets is equivalent to 10,000 bits. A BER of 10–4 implies 1 bit
error for every 10000 bits sent or received. Assuming the best case of only 1 bit error in a failed packet, having 1 failed
packet for every 63 received is about equal to a BER of 10–4.
c) UNRETURNED MESSAGES ALARMS

PATH: SETTINGS  PRODUCT SETUP  DIRECT I/O  UNRETURNED MESSAGES ALARM CH1(2)
 UNRETURNED UNRET MSGS ALARM CH1 Range: Enabled, Disabled

 MESSAGES ALARM CH1 FUNCTION: Disabled
5 MESSAGE
UNRET MSGS ALARM CH1 Range: 100 to 10000 in steps of 1
MESSAGE COUNT: 600
UNRET MSGS ALARM CH1 Range: 1 to 1000 in steps of 1
MESSAGE
THRESHOLD: 10
UNRET MSGS ALARM CH1 Range: Enabled, Disabled
MESSAGE
EVENTS: Disabled
The D60 checks integrity of the direct input and output communication ring by counting unreturned messages. In the ring
configuration, all messages originating at a given device should return within a pre-defined period of time. The unreturned
messages alarm function is available for monitoring the integrity of the communication ring by tracking the rate of unre-
turned messages. This function counts all the outgoing messages and a separate counter adds the messages have failed
to return. When the unreturned messages counter reaches the user-definable level specified by the UNRET MSGS ALARM
CH1 THRESHOLD setting and within the user-defined message count UNRET MSGS ALARM CH1 COUNT, the DIR IO CH1 UNRET
ALM FlexLogic operand is set.
When the total message counter reaches the user-defined maximum specified by the UNRET MSGS ALARM CH1 MESSAGE
COUNT setting, both the counters reset and the monitoring process is restarted.
The operand shall be configured to drive an output contact, user-programmable LED, or selected communication-based
output. Latching and acknowledging conditions, if required, should be programmed accordingly.
The unreturned messages alarm function is available on a per-channel basis and is active only in the ring configuration.
The total number of unreturned input and output messages is available as the ACTUAL VALUES  STATUS  DIRECT
INPUTS  UNRETURNED MSG COUNT CH1 actual value.

5.2.17 TELEPROTECTION
PATH: SETTINGS  PRODUCT SETUP  TELEPROTECTION
 TELEPROTECTION TELEPROTECTION Range: Disabled, Enabled

NUMBER OF TERMINALS: Range: 2, 3
MESSAGE
2
NUMBER OF COMM Range: 1, 2
MESSAGE
CHANNELS: 1
LOCAL RELAY ID Range: 0 to 255 in steps of 1
MESSAGE
NUMBER: 0
TERMINAL 1 RELAY ID Range: 0 to 255 in steps of 1
MESSAGE
NUMBER: 0
TERMINAL 2 RELAY ID Range: 0 to 255 in steps of 1
MESSAGE
NUMBER: 0
Digital teleprotection functionality is designed to transfer protection commands between two or three relays in a secure,
fast, dependable, and deterministic fashion. Possible applications are permissive or blocking pilot schemes and direct
transfer trip (DTT). Teleprotection can be applied over any analog or digital channels and any communications media, such
as direct fiber, copper wires, optical networks, or microwave radio links. A mixture of communication media is possible.
Once teleprotection is enabled and the teleprotection input/outputs are configured, data packets are transmitted continu-
ously every 1/4 cycle (3/8 cycle if using C37.94 modules) from peer-to-peer. Security of communication channel data is
achieved by using CRC-32 on the data packet.
5
Teleprotection inputs/outputs and direct inputs/outputs are mutually exclusive – as such, they cannot be used
simultaneously. Once teleprotection inputs and outputs are enabled, direct inputs and outputs are blocked, and vice
NOTE versa.
• NUMBER OF TERMINALS: Specifies whether the teleprotection system operates between two peers or three peers.
• NUMBER OF CHANNELS: Specifies how many channels are used. If the NUMBER OF TERMINALS is “3” (three-terminal
system), set the NUMBER OF CHANNELS to “2”. For a two-terminal system, the NUMBER OF CHANNELS can set to “1” or
“2” (redundant channels).
• LOCAL RELAY ID NUMBER, TERMINAL 1 RELAY ID NUMBER, and TERMINAL 2 RELAY ID NUMBER: In installa-
tions that use multiplexers or modems, it is desirable to ensure that the data used by the relays protecting a given line
is from the correct relays. The teleprotection function performs this check by reading the message ID sent by transmit-
ting relays and comparing it to the programmed ID in the receiving relay. This check is also used to block inputs if inad-
vertently set to loopback mode or data is being received from a wrong relay by checking the ID on a received channel.
If an incorrect ID is found on a channel during normal operation, the TELEPROT CH1 ID FAIL or TELEPROT CH2 ID FAIL
FlexLogic operand is set, driving the event with the same name and blocking the teleprotection inputs. For commis-
sioning purposes, the result of channel identification is also shown in the STATUS  CHANNEL TESTS  VALIDITY OF
CHANNEL CONFIGURATION actual value. The default value of “0” for the LOCAL RELAY ID NUMBER indicates that relay ID
is not to be checked. On two- terminals two-channel systems, the same LOCAL RELAY ID NUMBER is transmitted over
both channels; as such, only the TERMINAL 1 ID NUMBER has to be programmed on the receiving end.
5.2.18 INSTALLATION
PATH: SETTINGS  PRODUCT SETUP  INSTALLATION
 INSTALLATION RELAY SETTINGS: Range: Not Programmed, Programmed

 Not Programmed
RELAY NAME: Range: up to 20 alphanumeric characters
MESSAGE
Relay-1

To safeguard against the installation of a relay without any entered settings, the unit will not allow signaling of any output
relay until RELAY SETTINGS is set to "Programmed". This setting is defaulted to "Not Programmed" when at the factory. The
UNIT NOT PROGRAMMED self-test error message is displayed until the relay is put into the "Programmed" state.
The RELAY NAME setting allows the user to uniquely identify a relay. This name will appear on generated reports.

5 SETTINGS 5.3 REMOTE RESOURCES
5.3REMOTE RESOURCES 5.3.1 REMOTE RESOURCES CONFIGURATION
When D60 is ordered with a process card module as a part of HardFiber system, then an additional Remote Resources
menu tree is available in EnerVista UR Setup software to allow configuration of the HardFiber system.
Figure 5–23: REMOTE RESOURCES CONFIGURATION MENU

The remote resources settings configure a D60 with a process bus module to work with HardFiber Bricks. Remote
resources configuration is only available through the EnerVista UR Setup software, and is not available through the D60
front panel. A Brick provides eight AC measurements, along with contact inputs, DC analog inputs, and contact outputs, to 5
be the remote interface to field equipment such as circuit breakers and transformers. The D60 with a process bus module
has access to all of the capabilities of up to eight Bricks. Remote resources settings configure the point-to-point connection
between specific fiber optic ports on the D60 process card and specific Brick. The relay is then configured to measure spe-
cific currents, voltages and contact inputs from those Bricks, and to control specific outputs.
The configuration process for remote resources is straightforward and consists of the following steps.
• Configure the field units. This establishes the point-to-point connection between a specific port on the relay process
bus module, and a specific digital core on a specific Brick. This is a necessary first step in configuring a process bus
relay.
• Configure the AC banks. This sets the primary and secondary quantities and connections for currents and voltages.
AC bank configuration also provides a provision for redundant measurements for currents and voltages, a powerful
reliability improvement possible with process bus.
• Configure signal sources. This functionality of the D60 has not changed other than the requirement to use currents and
voltages established by AC bank configuration under the remote resources menu.
• Configure field contact inputs, field contact outputs, RTDs, and transducers as required for the application's functional-
ity. These inputs and outputs are the physical interface to circuit breakers, transformers, and other equipment. They
replace the traditional contact inputs and outputs located at the relay to virtually eliminate copper wiring.
• Configure shared inputs and outputs as required for the application's functionality. Shared inputs and outputs are dis-
tinct binary channels that provide high-speed protection quality signaling between relays through a Brick.
For additional information on how to configure a relay with a process bus module, see GE publication number GEK-113658:
HardFiber Process Bus System Instruction Manual.

5.4 SYSTEM SETUP 5 SETTINGS
5.4SYSTEM SETUP 5.4.1 AC INPUTS
a) CURRENT BANKS
PATH: SETTINGS  SYSTEM SETUP  AC INPUTS  CURRENT BANK F1(M5)
 CURRENT BANK F1 PHASE CT F1 Range: 1 to 65000 A in steps of 1

 PRIMARY: 1 A
PHASE CT F1 Range: 1 A, 5 A
MESSAGE
SECONDARY: 1 A
GROUND CT F1 Range: 1 to 65000 A in steps of 1
MESSAGE
PRIMARY: 1 A
GROUND CT F1 Range: 1 A, 5 A
MESSAGE
SECONDARY: 1 A
Because energy parameters are accumulated, these values should be recorded and then reset immediately
prior to changing CT characteristics.
NOTE
Four banks of phase and ground CTs can be set, where the current banks are denoted in the following format (X represents
the module slot position letter):
Xa, where X = {F, M} and a = {1, 5}.
See the Introduction to AC Sources section at the beginning of this chapter for additional details.
These settings are critical for all features that have settings dependent on current measurements. When the relay is
5 ordered, the CT module must be specified to include a standard or sensitive ground input. As the phase CTs are connected
in wye (star), the calculated phasor sum of the three phase currents (IA + IB + IC = neutral current = 3Io) is used as the
input for the neutral overcurrent elements. In addition, a zero-sequence (core balance) CT which senses current in all of the
circuit primary conductors, or a CT in a neutral grounding conductor may also be used. For this configuration, the ground
CT primary rating must be entered. To detect low level ground fault currents, the sensitive ground input may be used. In this
case, the sensitive ground CT primary rating must be entered. Refer to chapter 3 for more details on CT connections.
Enter the rated CT primary current values. For both 1000:5 and 1000:1 CTs, the entry would be 1000. For correct opera-
tion, the CT secondary rating must match the setting (which must also correspond to the specific CT connections used).
The following example illustrates how multiple CT inputs (current banks) are summed as one source current. Given the fol-
lowing current banks:
• F1: CT bank with 500:1 ratio.
• F5: CT bank with 1000:1 ratio.
• M1: CT bank with 800:1 ratio.
The following rule applies:
SRC 1 = F1 + F5 + M1 (EQ 5.6)
1 pu is the highest primary current. In this case, 1000 is entered and the secondary current from the 500:1 ratio CT will be
adjusted to that created by a 1000:1 CT before summation. If a protection element is set up to act on SRC 1 currents, then
a pickup level of 1 pu will operate on 1000 A primary.
The same rule applies for current sums from CTs with different secondary taps (5 A and 1 A).

5 SETTINGS 5.4 SYSTEM SETUP
b) VOLTAGE BANKS
PATH: SETTINGS  SYSTEM SETUP  AC INPUTS  VOLTAGE BANK F5(M5)
 VOLTAGE BANK F5 PHASE VT F5 Range: Wye, Delta

 CONNECTION: Wye
PHASE VT F5 Range: 25.0 to 240.0 V in steps of 0.1
MESSAGE
SECONDARY: 66.4 V
PHASE VT F5 Range: 1.00 to 24000.00 in steps of 0.01
MESSAGE
RATIO: 1.00 :1
AUXILIARY VT F5 Range: Vn, Vag, Vbg, Vcg, Vab, Vbc, Vca
MESSAGE
CONNECTION: Vag
AUXILIARY VT F5 Range: 25.0 to 240.0 V in steps of 0.1
MESSAGE
SECONDARY: 66.4 V
AUXILIARY VT F5 Range: 1.00 to 24000.00 in steps of 0.01
MESSAGE
RATIO: 1.00 :1
Because energy parameters are accumulated, these values should be recorded and then reset
immediately prior to changing VT characteristics.
Two banks of phase/auxiliary VTs can be set, where voltage banks are denoted in the following format (X represents the
module slot position letter):
Xa, where X = {F, M} and a = {5}.
See the Introduction to AC sources section at the beginning of this chapter for additional details.
5
With VTs installed, the relay can perform voltage measurements as well as power calculations. Enter the PHASE VT F5 CON-
NECTION made to the system as “Wye” or “Delta”. An open-delta source VT connection would be entered as “Delta”.
The nominal PHASE VT F5 SECONDARY voltage setting is the voltage across the relay input terminals when nominal
voltage is applied to the VT primary.
NOTE
For example, on a system with a 13.8 kV nominal primary voltage and with a 14400:120 volt VT in a delta connec-
tion, the secondary voltage would be 115; that is, (13800 / 14400) × 120. For a wye connection, the voltage value
entered must be the phase to neutral voltage which would be 115  3 = 66.4.
On a 14.4 kV system with a delta connection and a VT primary to secondary turns ratio of 14400:120, the voltage
value entered would be 120; that is, 14400 / 120.
5.4.2 POWER SYSTEM
PATH: SETTINGS  SYSTEM SETUP  POWER SYSTEM
 POWER SYSTEM NOMINAL FREQUENCY: Range: 25 to 60 Hz in steps of 1

 60 Hz
PHASE ROTATION: Range: ABC, ACB
MESSAGE
ABC
FREQUENCY AND PHASE Range: SRC 1, SRC 2, SRC 3, SRC 4
MESSAGE
REFERENCE: SRC 1
FREQUENCY TRACKING: Range: Disabled, Enabled
MESSAGE
Enabled
The power system NOMINAL FREQUENCY value is used as a default to set the digital sampling rate if the system frequency
cannot be measured from available signals. This may happen if the signals are not present or are heavily distorted. Before
reverting to the nominal frequency, the frequency tracking algorithm holds the last valid frequency measurement for a safe
period of time while waiting for the signals to reappear or for the distortions to decay.

The phase sequence of the power system is required to properly calculate sequence components and power parameters.
The PHASE ROTATION setting matches the power system phase sequence. Note that this setting informs the relay of the
actual system phase sequence, either ABC or ACB. CT and VT inputs on the relay, labeled as A, B, and C, must be con-
nected to system phases A, B, and C for correct operation.
The FREQUENCY AND PHASE REFERENCE setting determines which signal source is used (and hence which AC signal) for
phase angle reference. The AC signal used is prioritized based on the AC inputs that are configured for the signal source:
phase voltages takes precedence, followed by auxiliary voltage, then phase currents, and finally ground current.
For three phase selection, phase A is used for angle referencing ( V ANGLE REF = V A ), while Clarke transformation of the
phase signals is used for frequency metering and tracking ( V FREQUENCY =  2V A – V B – V C   3 ) for better performance dur-
ing fault, open pole, and VT and CT fail conditions.
The phase reference and frequency tracking AC signals are selected based upon the Source configuration, regardless of
whether or not a particular signal is actually applied to the relay.
Phase angle of the reference signal will always display zero degrees and all other phase angles will be relative to this sig-
nal. If the pre-selected reference signal is not measurable at a given time, the phase angles are not referenced.
The phase angle referencing is done via a phase locked loop, which can synchronize independent UR-series relays if they
have the same AC signal reference. This results in very precise correlation of phase angle indications between different
UR-series relays.
FREQUENCY TRACKING is set to “Disabled” only in unusual circumstances; consult the factory for special variable-
frequency applications.
NOTE
The frequency tracking feature functions only when the D60 is in the “Programmed” mode. If the D60 is “Not Pro-
grammed”, then metering values are available but can exhibit significant errors.
5
NOTE
5.4.3 SIGNAL SOURCES
PATH: SETTINGS  SYSTEM SETUP  SIGNAL SOURCES  SOURCE 1(4)
 SOURCE 1 SOURCE 1 NAME: Range: up to six alphanumeric characters

 SRC 1
SOURCE 1 PHASE CT: Range: None, F1, F5, F1+F5,... up to a combination of
MESSAGE any 6 CTs. Only Phase CT inputs are displayed.
None
SOURCE 1 GROUND CT: Range: None, F1, F5, F1+F5,... up to a combination of
MESSAGE any 6 CTs. Only Ground CT inputs are displayed.
None
SOURCE 1 PHASE VT: Range: None, F5, M5
MESSAGE Only phase voltage inputs will be displayed.
None
SOURCE 1 AUX VT: Range: None, F5, M5
MESSAGE Only auxiliary voltage inputs will be displayed.
None
Identical menus are available for each source. The "SRC 1" text can be replaced by with a user-defined name appropriate
for the associated source.
The first letter in the source identifier represents the module slot position. The number directly following this letter repre-
sents either the first bank of four channels (1, 2, 3, 4) called “1” or the second bank of four channels (5, 6, 7, 8) called “5” in
a particular CT/VT module. Refer to the Introduction to AC sources section at the beginning of this chapter for additional
details on this concept.
It is possible to select the sum of all CT combinations. The first channel displayed is the CT to which all others will be
referred. For example, the selection “F1+F5” indicates the sum of each phase from channels “F1” and “F5”, scaled to
whichever CT has the higher ratio. Selecting “None” hides the associated actual values.
The approach used to configure the AC sources consists of several steps; first step is to specify the information about each
CT and VT input. For CT inputs, this is the nominal primary and secondary current. For VTs, this is the connection type,
ratio and nominal secondary voltage. Once the inputs have been specified, the configuration for each source is entered,
including specifying which CTs will be summed together.

User selection of AC parameters for comparator elements:

CT/VT modules automatically calculate all current and voltage parameters from the available inputs. Users must select the
specific input parameters to be measured by every element in the relevant settings menu. The internal design of the ele-
ment specifies which type of parameter to use and provides a setting for source selection. In elements where the parameter
may be either fundamental or RMS magnitude, such as phase time overcurrent, two settings are provided. One setting
specifies the source, the second setting selects between fundamental phasor and RMS.
AC input actual values:
The calculated parameters associated with the configured voltage and current inputs are displayed in the current and volt-
age sections of actual values. Only the phasor quantities associated with the actual AC physical input channels will be dis-
played here. All parameters contained within a configured source are displayed in the sources section of the actual values.
DISTURBANCE DETECTORS (INTERNAL):
The disturbance detector (ANSI 50DD) element is a sensitive current disturbance detector that detects any disturbance on
the protected system. The 50DD function is used directly in some elements in the relay, for example VT Fuse Failure detec-
tor or Fault Report. It can also be used to supervise current-based elements to prevent maloperation as a result of the
wrong settings or external CT wiring problem. A disturbance detector is provided for each source.
The 50DD function responds to the changes in magnitude of the sequence currents. The disturbance detector scheme
logic is as follows:
SETTING
ACTUAL
PRODUCT SETUP/DISPLAY
SOURCE 1 PROPERTIES/CURRENT
CURRENT PHASOR CUT-OFF LEVEL
I_1 I_1 - I_1’ >2*CUT-OFF FLEXLOGIC OPERAND
I_2 I_2 - I_2’ >2*CUT-OFF OR SRC 1 50DD OP
I_0 I_0 - I_0’ >2*CUT-OFF
Where I’ is 2 cycles old
SETTING
5
ACTUAL
I_0 I_0 - I_0’ >2*CUT-OFF
SETTING
ACTUAL
I_0 I_0 - I_0’ >2*CUT-OFF
Where I’ is 2 cycles old 827092A3.CDR
Figure 5–24: DISTURBANCE DETECTOR LOGIC DIAGRAM

The disturbance detector responds to the change in currents of twice the current cut-off level. The default cut-off threshold
is 0.02 pu; thus by default the disturbance detector responds to a change of 0.04 pu. The metering sensitivity setting (PROD-
UCT SETUP  DISPLAY PROPERTIES  CURRENT CUT-OFF LEVEL) controls the sensitivity of the disturbance detector
accordingly.
EXAMPLE USE OF SOURCES:
An example of the use of sources is shown in the diagram below. A relay could have the following hardware configuration:
INCREASING SLOT POSITION LETTER -->
CT/VT MODULE 1 CT/VT MODULE 2 CT/VT MODULE 3
CTs VTs not applicable
This configuration could be used on a two-winding transformer, with one winding connected into a breaker-and-a-half sys-
tem. The following figure shows the arrangement of sources used to provide the functions required in this application, and
the CT/VT inputs that are used to provide the data.

F1 DSP Bank
F5
Source 1 Source 2
Amps Amps
Source 3
51BF-1 51BF-2
U1 Volts Amps
A W Var 87T
A W Var 51P
Volts Amps
M1
M1 Source 4
UR Relay
M5
Figure 5–25: EXAMPLE USE OF SOURCES
Y LV D HV AUX
SRC 1 SRC 2 SRC 3
5 Phase CT
Ground CT
M1
M1
F1+F5
None
None
None
Phase VT M5 None None
Aux VT None None U1

5.4.4 BREAKERS
PATH: SETTINGS  SYSTEM SETUP  BREAKERS  BREAKER 1(4)
 BREAKER 1 BREAKER 1 Range: Disabled, Enabled

BREAKER1 PUSH BUTTON Range: Disabled, Enabled
MESSAGE
CONTROL: Disabled
BREAKER 1 NAME: Range: up to 6 alphanumeric characters
MESSAGE
Bkr 1
BREAKER 1 MODE: Range: 3-Pole, 1-Pole
MESSAGE
3-Pole
BREAKER 1 OPEN: Range: FlexLogic operand
MESSAGE
Off
BREAKER 1 BLK OPEN: Range: FlexLogic operand
MESSAGE
Off
BREAKER 1 CLOSE: Range: FlexLogic operand
MESSAGE
Off
BREAKER 1 BLK CLOSE: Range: FlexLogic operand
MESSAGE
Off
BREAKER 1 A/3P CLSD: Range: FlexLogic operand
MESSAGE
Off 5
BREAKER 1 A/3P OPND: Range: FlexLogic operand
MESSAGE
Off
BREAKER 1 B CLOSED: Range: FlexLogic operand
MESSAGE
Off
BREAKER 1 B OPENED: Range: FlexLogic operand
MESSAGE
Off
BREAKER 1 C CLOSED: Range: FlexLogic operand
MESSAGE
Off
BREAKER 1 C OPENED: Range: FlexLogic operand
MESSAGE
Off
BREAKER 1 Toperate: Range: 0.000 to 65.535 s in steps of 0.001
MESSAGE
0.070 s
BREAKER 1 EXT ALARM: Range: FlexLogic operand
MESSAGE
Off
BREAKER 1 ALARM Range: 0.000 to 65.535 s in steps of 0.001
MESSAGE
DELAY: 0.000 s
MANUAL CLOSE RECAL1 Range: 0.000 to 65.535 s in steps of 0.001
MESSAGE
TIME: 0.000 s
BREAKER 1 OUT OF SV: Range: FlexLogic operand
MESSAGE
Off
BREAKER 1 EVENTS: Range: Disabled, Enabled
MESSAGE
Disabled

A description of the operation of the breaker control and status monitoring features is provided in chapter 4. Only informa-
tion concerning programming of the associated settings is covered here. These features are provided for two or more
breakers; a user may use only those portions of the design relevant to a single breaker, which must be breaker 1.
The number of breaker control elements is dependent on the number of CT/VT modules specified with the D60. The follow-
ing settings are available for each breaker control element.
• BREAKER 1 FUNCTION: This setting enables and disables the operation of the breaker control feature.
• BREAKER1 PUSH BUTTON CONTROL: Set to “Enable” to allow faceplate push button operations.
• BREAKER 1 NAME: Assign a user-defined name (up to six characters) to the breaker. This name will be used in flash
messages related to breaker 1.
• BREAKER 1 MODE: This setting selects “3-Pole” mode, where all breaker poles are operated simultaneously, or “1-
Pole” mode where all breaker poles are operated either independently or simultaneously.
• BREAKER 1 OPEN: This setting selects an operand that creates a programmable signal to operate an output relay to
open breaker 1.
• BREAKER 1 BLK OPEN: This setting selects an operand that prevents opening of the breaker. This setting can be
used for select-before-operate functionality or to block operation from a panel switch or from SCADA.
• BREAKER 1 CLOSE: This setting selects an operand that creates a programmable signal to operate an output relay
to close breaker 1.
• BREAKER 1 BLK CLOSE: This setting selects an operand that prevents closing of the breaker. This setting can be
used for select-before-operate functionality or to block operation from a panel switch or from SCADA.
• BREAKER 1 A/3P CLOSED: This setting selects an operand, usually a contact input connected to a breaker auxil-
iary position tracking mechanism. This input should be a normally-open 52/a status input to create a logic 1 when the
5 breaker is closed. If the BREAKER 1 MODE setting is selected as “3-Pole”, this setting selects a single input as the oper-
and used to track the breaker open or closed position. If the mode is selected as “1-Pole”, the input mentioned above
is used to track phase A and the BREAKER 1 B and BREAKER 1 C settings select operands to track phases B and C,
respectively.
• BREAKER 1 A/3P OPND: This setting selects an operand, usually a contact input, that should be a normally-closed
52/b status input to create a logic 1 when the breaker is open. If a separate 52/b contact input is not available, then the
inverted BREAKER 1 CLOSED status signal can be used.
• BREAKER 1 B CLOSED: If the mode is selected as three-pole, this setting has no function. If the mode is selected
as single-pole, this input is used to track the breaker phase B closed position as above for phase A.
• BREAKER 1 B OPENED: If the mode is selected as three-pole, this setting has no function. If the mode is selected
as single-pole, this input is used to track the breaker phase B opened position as above for phase A.
• BREAKER 1 C CLOSED: If the mode is selected as three-pole, this setting has no function. If the mode is selected
as single-pole, this input is used to track the breaker phase C closed position as above for phase A.
• BREAKER 1 C OPENED: If the mode is selected as three-pole, this setting has no function. If the mode is selected
as single-pole, this input is used to track the breaker phase C opened position as above for phase A.
• BREAKER 1 Toperate: This setting specifies the required interval to overcome transient disagreement between the
52/a and 52/b auxiliary contacts during breaker operation. If transient disagreement still exists after this time has
expired, the BREAKER 1 BAD STATUS FlexLogic operand is asserted from alarm or blocking purposes.
• BREAKER 1 EXT ALARM: This setting selects an operand, usually an external contact input, connected to a breaker
alarm reporting contact.
• BREAKER 1 ALARM DELAY: This setting specifies the delay interval during which a disagreement of status among
the three-pole position tracking operands will not declare a pole disagreement. This allows for non-simultaneous oper-
ation of the poles.
If single-pole tripping and reclosing is used, the breaker may trip unsymmetrically for faults. In this case, the minimum
alarm delay setting must exceed the maximum time required for fault clearing and reclosing by a suitable margin.
• MANUAL CLOSE RECAL1 TIME: This setting specifies the interval required to maintain setting changes in effect after
an operator has initiated a manual close command to operate a circuit breaker.
• BREAKER 1 OUT OF SV: Selects an operand indicating that breaker 1 is out-of-service.

Figure 5–26: DUAL BREAKER CONTROL SCHEME LOGIC (Sheet 1 of 2)

IEC 61850 functionality is permitted when the D60 is in “Programmed” mode and not in the local control mode.
NOTE

Figure 5–27: DUAL BREAKER CONTROL SCHEME LOGIC (Sheet 2 of 2)

The breaker element has direct hard-coded connections to IEC 61850 model as shown in the logic diagram. This allows
remote open/close operation of each breaker, using either CSWI or XCBR IEC 61850 logical nodes. IEC 61850 select-
before-operate functionality, local/remote switch functionality along with a blocking of open/close commands are provided.
Note that IEC 61850 commands are event-driven and dwell time for these is one protection pass only. If you want to main-
tain the close/open command for a certain time, do so either on the contact outputs using the "Seal-in" setting or in Flex-
Logic.

5.4.5 DISCONNECT SWITCHES
PATH: SETTINGS  SYSTEM SETUP  SWITCHES  SWITCH 1(16)
 SWITCH 1 SWITCH 1 Range: Disabled, Enabled

SWITCH 1 NAME: Range: up to 6 alphanumeric characters
MESSAGE
SW 1
SWITCH 1 MODE: Range: 3-Pole, 1-Pole
MESSAGE
3-Pole
SWITCH 1 OPEN: Range: FlexLogic operand
MESSAGE
Off
SWITCH 1 BLK OPEN: Range: FlexLogic operand
MESSAGE
Off
SWITCH 1 CLOSE: Range: FlexLogic operand
MESSAGE
Off
SWITCH 1 BLK CLOSE: Range: FlexLogic operand
MESSAGE
Off
SWTCH 1 A/3P CLSD: Range: FlexLogic operand
MESSAGE
Off
SWTCH 1 A/3P OPND: Range: FlexLogic operand
MESSAGE
Off 5
SWITCH 1 B CLOSED: Range: FlexLogic operand
MESSAGE
Off
SWITCH 1 B OPENED: Range: FlexLogic operand
MESSAGE
Off
SWITCH 1 C CLOSED: Range: FlexLogic operand
MESSAGE
Off
SWITCH 1 C OPENED: Range: FlexLogic operand
MESSAGE
Off
SWITCH 1 Toperate: Range: 0.000 to 65.535 s in steps of 0.001
MESSAGE
0.070 s
SWITCH 1 ALARM Range: 0.000 to 65.535 s in steps of 0.001
MESSAGE
DELAY: 0.000 s
SWITCH 1 EVENTS: Range: Disabled, Enabled
MESSAGE
Disabled
The disconnect switch element contains the auxiliary logic for status and serves as the interface for opening and closing of
disconnect switches from SCADA or through the front panel interface. The disconnect switch element can be used to cre-
ate an interlocking functionality. For greater security in determination of the switch pole position, both the 89/a and 89/b
auxiliary contacts are used with reporting of the discrepancy between them. The number of available disconnect switches
depends on the number of the CT/VT modules ordered with the D60.
• SWITCH 1 FUNCTION: This setting enables and disables the operation of the disconnect switch element.
• SWITCH 1 NAME: Assign a user-defined name (up to six characters) to the disconnect switch. This name will be used
in flash messages related to disconnect switch 1.
• SWITCH 1 MODE: This setting selects “3-Pole” mode, where disconnect switch poles have a single common auxiliary
switch, or “1-Pole” mode where each disconnect switch pole has its own auxiliary switch.

• SWITCH 1 OPEN: This setting selects an operand that creates a programmable signal to operate a contact output to
open disconnect switch 1.
• SWITCH 1 BLK OPEN: This setting selects an operand that prevents opening of the disconnect switch. This setting
can be used for select-before-operate functionality or to block operation from a panel switch or from SCADA.
• SWITCH 1 CLOSE: This setting selects an operand that creates a programmable signal to operate a contact output to
close disconnect switch 1.
• SWITCH 1 BLK CLOSE: This setting selects an operand that prevents closing of the disconnect switch. This setting
can be used for select-before-operate functionality or to block operation from a panel switch or from SCADA.
• SWTCH 1 A/3P CLSD: This setting selects an operand, usually a contact input connected to a disconnect switch
auxiliary position tracking mechanism. This input should be a normally-open 89/a status input to create a logic 1 when
the disconnect switch is closed. If the SWITCH 1 MODE setting is selected as “3-Pole”, this setting selects a single input
as the operand used to track the disconnect switch open or closed position. If the mode is selected as “1-Pole”, the
input mentioned above is used to track phase A and the SWITCH 1 B and SWITCH 1 C settings select operands to
track phases B and C, respectively.
• SWTCH 1 A/3P OPND: This setting selects an operand, usually a contact input, that should be a normally-closed 89/
b status input to create a logic 1 when the disconnect switch is open. If a separate 89/b contact input is not available,
then an inverted 89/a status signal can be used.
• SWITCH 1 B CLOSED: If the mode is selected as three-pole, this setting has no function. If the mode is selected as
single-pole, this input is used to track the disconnect switch phase B closed position as above for phase A.
• SWITCH 1 B OPENED: If the mode is selected as three-pole, this setting has no function. If the mode is selected as
single-pole, this input is used to track the disconnect switch phase B opened position as above for phase A.
• SWITCH 1 C CLOSED: If the mode is selected as three-pole, this setting has no function. If the mode is selected as
5 single-pole, this input is used to track the disconnect switch phase C closed position as above for phase A.
• SWITCH 1 C OPENED: If the mode is selected as three-pole, this setting has no function. If the mode is selected as
single-pole, this input is used to track the disconnect switch phase C opened position as above for phase A.
• SWITCH 1 Toperate: This setting specifies the required interval to overcome transient disagreement between the 89/a
and 89/b auxiliary contacts during disconnect switch operation. If transient disagreement still exists after this time has
expired, the SWITCH 1 BAD STATUS FlexLogic operand is asserted from alarm or blocking purposes.
• SWITCH 1 ALARM DELAY: This setting specifies the delay interval during which a disagreement of status among the
three-pole position tracking operands will not declare a pole disagreement. This allows for non-simultaneous operation
of the poles.
IEC 61850 functionality is permitted when the D60 is in “Programmed” mode and not in the local control mode.
NOTE

Figure 5–28: DISCONNECT SWITCH SCHEME LOGIC

The switch element has direct hard-coded connections to IEC 61850 model as shown in the logic diagram. This allows
remote open/close operation of each switch, using either CSWI or XSWI IEC 61850 logical nodes. IEC 61850 select-
before-operate functionality, local/remote switch functionality along with a blocking open/close commands are provided.
Note that IEC 61850 commands are event-driven and dwell time for these is one protection pass only. If you want to main-
tain close/open command for a certain time, do so either on the contact outputs using the "Seal-in" setting or in FlexLogic.
5.4.6 FLEXCURVES
a) SETTINGS
PATH: SETTINGS  SYSTEM SETUP  FLEXCURVES  FLEXCURVE A(D)
 FLEXCURVE A FLEXCURVE A TIME AT Range: 0 to 65535 ms in steps of 1

 0.00 xPKP: 0 ms
FlexCurves A through D have settings for entering times to reset and operate at the following pickup levels: 0.00 to 0.98
and 1.03 to 20.00. This data is converted into two continuous curves by linear interpolation between data points. To enter a
custom FlexCurve, enter the reset and operate times (using the VALUE keys) for each selected pickup point (using the
MESSAGE UP/DOWN keys) for the desired protection curve (A, B, C, or D).
Table 5–10: FLEXCURVE TABLE

RESET TIME RESET TIME OPERATE TIME OPERATE TIME OPERATE TIME OPERATE TIME
MS MS MS MS MS MS
0.00 0.68 1.03 2.9 4.9 10.5
0.05 0.70 1.05 3.0 5.0 11.0
5 0.10 0.72 1.1 3.1 5.1 11.5
0.15 0.74 1.2 3.2 5.2 12.0
0.20 0.76 1.3 3.3 5.3 12.5
0.25 0.78 1.4 3.4 5.4 13.0
0.30 0.80 1.5 3.5 5.5 13.5
0.35 0.82 1.6 3.6 5.6 14.0
0.40 0.84 1.7 3.7 5.7 14.5
0.45 0.86 1.8 3.8 5.8 15.0
0.48 0.88 1.9 3.9 5.9 15.5
0.50 0.90 2.0 4.0 6.0 16.0
0.52 0.91 2.1 4.1 6.5 16.5
0.54 0.92 2.2 4.2 7.0 17.0
0.56 0.93 2.3 4.3 7.5 17.5
0.58 0.94 2.4 4.4 8.0 18.0
0.60 0.95 2.5 4.5 8.5 18.5
0.62 0.96 2.6 4.6 9.0 19.0
0.64 0.97 2.7 4.7 9.5 19.5
0.66 0.98 2.8 4.8 10.0 20.0

The relay using a given FlexCurve applies linear approximation for times between the user-entered points. Special
care must be applied when setting the two points that are close to the multiple of pickup of 1; that is, 0.98 pu and
NOTE
1.03 pu. It is recommended to set the two times to a similar value; otherwise, the linear approximation may result in
undesired behavior for the operating quantity that is close to 1.00 pu.
b) FLEXCURVE CONFIGURATION WITH ENERVISTA UR SETUP

The EnerVista UR Setup software allows for easy configuration and management of FlexCurves and their associated data
points. Prospective FlexCurves can be configured from a selection of standard curves to provide the best approximate fit,
then specific data points can be edited afterwards. Alternately, curve data can be imported from a specified file (.csv format)
by selecting the Import Data From EnerVista UR Setup setting.
Curves and data can be exported, viewed, and cleared by clicking the appropriate buttons. FlexCurves are customized by
editing the operating time (ms) values at pre-defined per-unit current multiples. Note that the pickup multiples start at zero
(implying the "reset time"), operating time below pickup, and operating time above pickup.
c) RECLOSER CURVE EDITING

Recloser curve selection is special in that recloser curves can be shaped into a composite curve with a minimum response
time and a fixed time above a specified pickup multiples. There are 41 recloser curve types supported. These definite oper-
ating times are useful to coordinate operating times, typically at higher currents and where upstream and downstream pro-
tective devices have different operating characteristics. The recloser curve configuration window shown below appears
when the Initialize From EnerVista UR Setup setting is set to “Recloser Curve” and the Initialize FlexCurve button is
clicked.
Multiplier: Scales (multiplies) the curve operating times
Addr: Adds the time specified in this field (in ms) to each
5
curve operating time value.
Minimum Response Time (MRT): If enabled, the MRT setting

defines the shortest operating time even if the curve suggests
a shorter time at higher current multiples. A composite operating
characteristic is effectively defined. For current multiples lower
than the intersection point, the curve dictates the operating time;
otherwise, the MRT does. An information message appears
when attempting to apply an MRT shorter than the minimum
curve time.
High Current Time: Allows the user to set a pickup multiple

from which point onwards the operating time is fixed. This is
normally only required at higher current levels. The HCT Ratio
defines the high current pickup multiple; the HCT defines the
operating time.
842721A1.CDR
Figure 5–29: RECLOSER CURVE INITIALIZATION

The multiplier and adder settings only affect the curve portion of the characteristic and not the MRT and HCT set-
tings. The HCT settings override the MRT settings for multiples of pickup greater than the HCT ratio.
NOTE

d) EXAMPLE
A composite curve can be created from the GE_111 standard with MRT = 200 ms and HCT initially disabled and then
enabled at eight (8) times pickup with an operating time of 30 ms. At approximately four (4) times pickup, the curve operat-
ing time is equal to the MRT and from then onwards the operating time remains at 200 ms (see below).
842719A1.CDR
Figure 5–30: COMPOSITE RECLOSER CURVE WITH HCT DISABLED

With the HCT feature enabled, the operating time reduces to 30 ms for pickup multiples exceeding 8 times pickup.
842720A1.CDR
Figure 5–31: COMPOSITE RECLOSER CURVE WITH HCT ENABLED

Configuring a composite curve with an increase in operating time at increased pickup multiples is not allowed. If this
is attempted, the EnerVista UR Setup software generates an error message and discards the proposed changes.
NOTE
e) STANDARD RECLOSER CURVES

The standard recloser curves available for the D60 are displayed in the following graphs.

1 GE106
0.5
0.2
TIME (sec)
GE103
GE104 GE105
0.1
0.05
GE101 GE102
0.02
0.01
1 1.2 1.5 2 2.5 3 4 5 6 7 8 9 10 12 15 20
CURRENT (multiple of pickup) 842723A1.CDR
5
Figure 5–32: RECLOSER CURVES GE101 TO GE106
50
20 GE142
10
5
GE138
TIME (sec)
1 GE120
GE113
0.5
0.2
0.1
0.05
1 1.2 1.5 2 2.5 3 4 5 6 7 8 9 10 12 15 20
Figure 5–33: RECLOSER CURVES GE113, GE120, GE138 AND GE142

50
20
10
GE201
TIME (sec)
GE151
2
GE134 GE140
1
GE137
0.5
1 1.2 1.5 2 2.5 3 4 5 6 7 8 9 10 12 15 20
5
Figure 5–34: RECLOSER CURVES GE134, GE137, GE140, GE151 AND GE201
50
GE152
20
TIME (sec)
GE141
10
GE131
5
GE200
2
1 1.2 1.5 2 2.5 3 4 5 6 7 8 9 10 12 15 20
Figure 5–35: RECLOSER CURVES GE131, GE141, GE152, AND GE200

50
20
GE164
10
2
TIME (sec)
GE162
1
0.5
GE133
0.2
GE165
0.1
0.05
GE161
0.02 GE163
0.01
1 1.2 1.5 2 2.5 3 4 5 6 7 8 9 10 12 15 20
Figure 5–36: RECLOSER CURVES GE133, GE161, GE162, GE163, GE164 AND GE165 5
20
GE132
10
1
TIME (sec)
0.5 GE139
0.2
GE136
0.1
GE116
0.05
GE118 GE117
0.02
0.01
1 1.2 1.5 2 2.5 3 4 5 6 7 8 9 10 12 15 20
Figure 5–37: RECLOSER CURVES GE116, GE117, GE118, GE132, GE136, AND GE139

20
10
5
GE122
2
1
TIME (sec)
0.5
GE114
0.2
GE111
GE121
0.1
0.05 GE115 GE112

GE107
0.02
0.01
1 1.2 1.5 2 2.5 3 4 5 6 7 8 9 10 12 15 20
CURRENT (multiple of pickup)
5
842724A1.CDR
Figure 5–38: RECLOSER CURVES GE107, GE111, GE112, GE114, GE115, GE121, AND GE122
50
20
GE202
10
TIME (sec)
GE135
2 GE119
0.5
0.2
1 1.2 1.5 2 2.5 3 4 5 6 7 8 9 10 12 15 20
Figure 5–39: RECLOSER CURVES GE119, GE135, AND GE202

5.4.7 PHASOR MEASUREMENT UNIT
a) MAIN MENU
PATH: SETTINGS  SYSTEM SETUP  PHASOR MEASUREMENT UNIT
 PHASOR MEASUREMENT  PHASOR MEASUREMENT

See below.
 UNIT  UNIT 1
 AGGREGATOR
 UNIT 1
 IEC 90-5 MSVCB
 CONFIGURATION
The D60 Line Distance Protection System is provided with an optional phasor measurement unit feature.
This feature is specified as a software option at the time of ordering. The number of phasor measurement
units available is also dependent on this option. See the Ordering section of chapter 2 for details.
UR Synchrophasor Implementation
PHASORS are used within protection relays. If these phasors are referenced to a common time base they are referred to as
a SYNCHROPHASOR. A vastly improved method for tracking power system dynamic phenomena for improved power system
monitoring, protection, operation, and control can be realized if Synchrophasors from different locations within the power
system are networked to a central location.
The D60 offers PMU features over two communication standards, IEC61850-9-5 and IEEE C37.118. The figure shows
complete Synchrophasor implementation.
5
Figure 5–40: COMPLETE SYNCHROPHASOR IMPLEMENTATION

UR Implementation of IEC61850-90-5
Synchrophasor data as measured and calculated by phasor measurement units (PMUs) is very useful to assess the condi-
tion of the electrical power network. The IEEE C37.118 standards define synchrophasors and related message formats to
transmit synchrophasor data. Synchrophasor streaming via IEEE C37.118 has proven to work but the desire to have a
communication mechanism that is compliant with the concept of IEC 61850 has led to the development of IEC61850-90-5.
The IEC61850-90-5 standard defines the packet structure for multicast routing of streamed Sampled Value (SV) known as
R-SV.

Firmware versions 7.0 and above have a 90-5 based R-SV implementation equivalent in structure and configuration to that
of the existing C37.118 implementation of firmware version 6.0, that is, synchrophasor data at rates up to 60 Hz for meter-
ing and 120 Hz for protection class synchrophasors. The two figures below depict the general data flow for the generation
of synchrophasor data for IEC61850-90-5. In the first figure, when IEC61850-90-5 is selected all real and virtual sources
are available for the IEC61850-90-5 PMUs.
Firmware version 7.0 allows the N60 to support a maximum of four Logical Device PMUs (Logical Device 2 through 5) and
four aggregators (located in Logical Device 1 (LD1)), while other UR family members support one PMU and only one
aggregator. The control blocks for the aggregators are located in LD1. A 64 char LDName setting is provided, see figure
below..
Figure 5–41: N60 SUPPORT FOR FOUR LOGICAL DEVICE PMUS

The specifics of implementation by model number is summarized in the table below.
Table 5–11: IMPLEMENTATION BY MODEL NUMBER
MODEL NUMBER OF NUMBER OF NUMBER OF ANALOG
PMUS AGGREGATORS INPUTS
N60 4 4 16
D60, F60, G60, L30, 1 1 16
L90, T60
Precise time input to the relay from the international time standard, via either IRIG-B or PTP, is vital for correct syn-
chrophasor measurement and reporting. For IRIG-B, a DC level shift IRIG-B receiver must be used for the phasor
NOTE measurement unit to output proper synchrophasor values.

Depending on the applied filter, the Synchrophasors that are produced by PMUs are classified as either P (protection) or M
(Measurement) class Synchrophasors. Synchrophasors available within the UR that have no filtering applied are classified
as NONE which within the standard is classified as PRES OR UNKNOWN under the Calculation Method - ClcMth. Each
Logical Device PMU supports one MxxMMXU, MxxMSQI, PxxxMMXU , PxxxMSQI, NxxMMXU, and one NxxMSQI logical
node.
Figure 5–42: LOGICAL NODES SUPPORTED IN EACH LOGICAL DEVICE

The following is a summary of LNs that are in each Logical Device (LD2 through LD5):
- PxxxMMXU1 ClcMth = P-Class (Note Vaux is mapped to Vneut of MMXU)
- PxxxMSQI1 ClcMth = P-CLASS
5
- MxxMMXU1 ClcMth = M-Class (Note Vaux is mapped to Vneut of MMXU)
- MxxMSQI1 ClcMth = M-CLASS
- NxxMMXU1 ClcMth = M-Class (Note Vaux is mapped to Vneut of MMXU)
- NxxMSQI1 ClcMth = M-CLASS
- GGIO1 which contains 16 digital status indication points and 16 analog points. The Analog GGIO values are selectable
from any FlexAnalog value in the UR.
The Synchro Logical Nodes in an LD report at the same rate as set in the PMUn Basic Configuration setting. This is
reflected in the instantiation of the Data Object – SmpRate in the msvcb## of LLN0 in the LD1. SmpRate is a Read
NOTE Only Integer Status (INS).
When the first PMU from any LD is mapped into an aggregator, the aggregator inherits the Sample Rate (SmpRate) and
IEEC C37.118 Class (P or M) of that PMU. The value of the SmpRate DO in the Report Control Block is set based on the
value of the Sample Rate in the PMU. The Class of the Dataset are mapped into the MSVID of the Dataset (see text below
for the overall name of the MSVID). If other PMUs are mapped into the same aggregator with different Sample Rates or
from different classes, then a Self-Test error (DatSetErr) is set and dataset transmission is blocked.
A setting value – MSVID – is created with a maximum input range of 56 characters (=64 less 6 for the IDCode less 2 for the
Class).
The value of MSVID in the dataset is a concatenation of the aggregator IDCode and the MSVID setting value in the format:
MSVID-AggregatorIDCode-CLASS where CLASS is P, M, or N (for None) – depending on the Class of the first PMU
included in the Aggregator.
Synchrophasor Rectangular Format and Integer data types are NOT supported in IEC 61850-90-5 (only supported
with IEEE C37.118) and not to set — GGIO1 which contains 16 digital status indication points — aggregated as a
NOTE 16 bit bitstring and 16 analog points. The Analog GGIO values are selectable from any FlexAnalog value in the UR.
For version 7.0 and later the description fields for the phasors, analog and digital channels are populated with the
16 character name field provided within the Basic Configuration menu. Additionally, the names of the 16 binary
points are implemented as numbered descriptions — d1, d2, d3, and so on. The number of descriptions are equal
to the number of bits configured in the 16 bit digital status word.

All bitstrings less than or equal to 32 bits in length map into a 32 bit bitstring in an IEC 61850-90-5 dataset.
NOTE
The Value of the Nominal Frequency of the chassis is instantiated as a DO in LPHD of LD1. The value is named
HzNom and is an Integer Status (INS).
The UR also supports the option to apply no filtering to the synchrophasors. If no filtering is applied (PMU Class = None),
according to the standard the ClcMth attribute will be PRES. The semantic of the ClcMth used is not carried in the individual
DO and so it is recommended that one of letters of the prefix on the instantiated LNs be set to “P” or “M” accordingly in
order to differentiate. For version 7.0 only FCDA data is supported. The Implementation by Model Number table, see
above, describes the maximum size of each PMU data set for version 7.0 using FCDA data (non-structured data).
EXAMPLE: PROTECTION SYNCHROPHASORS DATA SET WITH REPORTING RATE 60 FRAMES/SECOND
This example gives the protection synchrophasors data set with a reporting rate of 60 frames per second (P60MMXU1).
See figure above, Logical Nodes Supported in Each Logical Device. This data or list of items, see figure below, is not avail-
able to the UR setup program but is available to be mapped by the user into a selected aggregator or aggregators dataset.
The logical device name – LDName - of each PMU LD will be a 64 character user setting. The C37.118 STN and IDCode is
to be mapped as a concatenated value in the (d)escription field of LPL CDC of the NamPlt DO in LLN0. The mapping is
implemented as STN-IDCode(text string).
From each PMU the user selects the phasor information of interest that is mapped into the selected aggregator datset(s).
For version 7.0 only FCDA data is supported.
Figure 5–43: DATA SET CREATED FROM USER SELECTED INTERNAL ITEMS

EXAMPLE: THE CREATION OF DIFFERENT DATA SETS

The aggregators allow the aggregation of phasors from multiple PMUs (with the same reporting rate) into a single custom
data set to optimize bandwidth when streaming.
Figure 5–44: EXAMPLE OF AGGREGATOR DATA SETS

CONFIGURATION EXAMPLE: CFG-2 BASED CONFIGURATION (USING IEC61850-90-5)
The D60 is expected to send the CFG-2 file (IEEE C37.118 config. file) upon request from the upstream synchrophasor 5
devices (e.g., P30) without stopping R-SV multicasting, see figure below. The primary domain controller (PDC) does not
need to use a stop/start data stream command if the UR protocol is set to IEC61850-90-5 prior to requesting the configura-
tion via CFG-2 (IEEE C37.118 config. file). The CFG-2 request from the P30 can be on TCP/IP or UDP/IP, however, R-SV
data streaming is only UDP multicasts (not TCP).
Figure 5–45: CFG-2 BASED CONFIGURATION SOLUTION

MODIFICATION OF SYNC WORD IN CFG-2 FOR TR 90-5 DATA SETS

In the CFG-2 file, all relevant information about the data being streamed is included. However, this file does not include the
fact that it describes a 90-5 dataset or the number of Application Service Data Units (datasets). In order to communicate
this information via the CFG-2 file for a given aggregator, when the aggregator is set to 90-5, the version number of the
CFG-2 file (found in bits 0-3 of the frame SYNC word - which should presently be set to 2) is set as follows:
VALUE
(DECIMAL) # OF ASDUS
11 1
12 2
13 3
14 4
The PMU settings are organized in logical groups as follows.

PATH: SETTINGS  SYSTEM SETUP  PHASOR MEASUREMENT UNIT  PHASOR MEASUREMENT UNIT 1
 PHASOR MEASUREMENT  PMU 1 BASIC

See page 5-115.
 UNIT 1  CONFIGURATION
 PMU 1
 CALIBRATION
 PMU 1
 TRIGGERING
 PMU 1
5 MESSAGE
 RECORDING
See page 5-127.

b) BASIC CONFIGURATION
PATH: SETTINGS  SYSTEM SETUP PHASOR MEASUREMENT BASIC CONFIGURATION PMU1
 PMU 1 BASIC PMU 1 Range: Enabled, Disabled

 CONFIGURATION FUNCTION: Disabled Default: Disabled
PMU 1 IDCODE: Range: 1 to 65534 in steps of 1

MESSAGE
1 Default: 1
PMU 1 STN: Range: 32-character ASCII string truncated to 16

MESSAGE characters if mapped into C37.118 Default: GE-UR-PMU
GE-UR-PMU
PMU 1 SIGNAL SOURCE: Range: Available signal sources
MESSAGE
SRC 1 Default: SRC 1
PMU 1 CLASS: Range: None, CLASS M, CLASS P

MESSAGE
M-CLASS Default: M-CLASS
PMU 1 RATE: Range:1/sec, 2/sec, 4/sec, 5/sec, 10/sec, 12/sec, 15/sec,

MESSAGE 20/sec, 25/sec, 30/sec, 50/sec, 60/sec, 100/sec, 120/sec
10/sec
PMU 1 PHS-1: Range: Available synchrophasor values

MESSAGE
Off Default: Off
PMU 1 PHS-1 Range: 16 -character ASCII string

MESSAGE
NAME: GE-UR-PMU-PHS-1 Default: GE-UR-PMU-PHS-1
MESSAGE
PMU 1 PHS-14:
Off
Range: Available synchrophasor values
Default: Off 5
PMU 1 PHS-14: Range: 16 -character ASCII string
MESSAGE
NAME: GE-UR-PMU-PHS-14 Default: GE-UR-PMU-PHS-14
PMU 1 A-CH-1: Range: Available FlexAnalog values

MESSAGE
Off Default: Off
PMU 1 A-CH-1: Range: 16 -character ASCII string

MESSAGE
NAME: AnalogChannel1 Default: AnalogChannel1
PMU 1 A-CH-16 (16): Range: Available FlexAnalog values

MESSAGE
Off Default: Off
PMU 1 A-CH-16 (16): Range: 16 -character ASCII string

MESSAGE
NAME: AnalogChannel16 Default: AnalogChannel8
PMU 1 D-CH-1: Range: Available FlexLogic operands

MESSAGE
Off Default: Off
PMU 1 D-CH-1 Range: 16 character ASCII string

MESSAGE
NAME: DigChannel1 Default: DigChannel1
PMU 1 D-CH-1 Range: Off, On

MESSAGE
NORMAL STATE: Off Default: Off
PMU 1 D-CH-16: Range: FlexLogic operand

MESSAGE
Off Default: Off
PMU 1 REC D-CH-16 Range: 16-character ASCII string

MESSAGE
NAME: DigChannel16 Default: DigChannel16

PMU 1 REC D-CH-16 Range: Off, On

MESSAGE
NORMAL STATE: Off Default: Off
 37.118 PMU 1
MESSAGE See below
 CONFIGURATION
 90-5 PMU 1
MESSAGE See below.
 CONFIGURATION
This section contains basic phasor measurement unit (PMU) data, such as functions, source settings, and names.
• PMU 1 FUNCTION: This setting enables the LOGICAL Device PMU 1 functionality. Use this setting to permanently
enable or disable the feature.
• PMU 1 IDCODE: This setting assigns a numerical ID to the PMU. It corresponds to the IDCODE field of the data, con-
figuration, header, and command frames of the IEEE C37.118 protocol. The PMU uses this value when sending data,
configuration, and header frames; and it responds to this value when receiving the command frame. This is used when
only data from one PMU is present.
• PMU 1 STN: This setting assigns an alphanumeric ID to the PMU station. It corresponds to the STN field of the config-
uration frame of the IEEE C37.118 protocol. This value is a 16-character ASCII string as per the IEEE C37.118 stan-
dard.
• PMU 1 SIGNAL SOURCE: This setting specifies one of the available D60 signal sources for processing in the PMU.
Note that any combination of voltages and currents can be configured as a source. The current channels could be con-
figured as sums of physically connected currents. This facilitates PMU applications in breaker-and-a-half, ring-bus, and
similar arrangements. The PMU feature calculates voltage phasors for actual voltage (A, B, C, and auxiliary) and cur-
rent (A, B, C, and ground) channels of the source, as well as symmetrical components (0, 1, and 2) of both voltages
5 and currents. When configuring communication and recording features of the PMU, the user could select – from the
above superset – the content to be sent out or recorded. When one source is selected by one PMU, it cannot be
selected by another PMU.
• PMU 1 CLASS (Range P, M, None): This setting selects the synchrophasor class. Note that a reporting rate of 100 or
120 can only be selected for class P synchrophasors and if the system frequency is 50 Hz or 60 Hz, respectively.
• PMU 1 NETWORK REPORTING FORMAT: This setting selects whether synchrophasors are reported as 16-bit inte-
gers or 32-bit IEEE floating point numbers. This setting complies with bit-1 of the FORMAT field of the IEEE C37.118
configuration frame. This setting applies to synchrophasors only; the user-selectable FlexAnalog channels are always
transmitted as 16-bit integer values.
• PMU 1 NETWORK REPORTING STYLE: This setting selects whether synchrophasors are reported in rectangular
(real and imaginary) coordinates or in polar (magnitude and angle) coordinates. This setting complies with bit-0 of the
FORMAT field of the IEEE C37.118 configuration frame.
• PMU 1 RATE: This setting specifies the reporting rate for the network (Ethernet) port. This value applies to all PMU
streams of the device that are assigned to transmit over this aggregator. For a system frequency of 60 Hz (50 Hz), the
D60 generates a reporting mismatch message if the selected rate is not set as 10 Hz, 12 Hz, 15 Hz, 20 Hz, 30 Hz,
60 Hz, or 120 Hz (or 10 Hz, 25 Hz, 50 Hz or 100 Hz when the system frequency is 50 Hz) when entered via the keypad
or software; and the D60 stops the transmission of reports. Note that 4 Hz is not allowed for an M-class 50 Hz system).

• PMU1 PHS-1 to PMU1 PHS-14: These settings specify synchrophasors to be transmitted from the superset of all syn-
chronized measurements. The available synchrophasor values are tabulated below.
SELECTION MEANING
Va First voltage channel, either Va or Vab
Vb Second voltage channel, either Vb or Vbc
Vc Third voltage channel, either Vc or Vca
Vx Fourth voltage channel
Ia Phase A current, physical channel or summation as per the source settings
Ib Phase B current, physical channel or summation as per the source settings
Ic Phase C current, physical channel or summation as per the source settings
Ig Fourth current channel, physical or summation as per the source settings
V1 Positive-sequence voltage, referenced to Va
V2 Negative-sequence voltage, referenced to Va
V0 Zero-sequence voltage
I1 Positive-sequence current, referenced to Ia
I2 Negative-sequence current, referenced to Ia
I0 Zero-sequence current
These settings allow for optimizing the frame size and maximizing transmission channel usage, depending on a given
application. Select “Off” to suppress transmission of a given value.
• PMU1 PHS-1 NM to PMU1 PHS-14 NM: These settings allow for custom naming of the synchrophasor channels. Six-
teen-character ASCII strings are allowed as in the CHNAM field of the configuration frame. These names are typically
based on station, bus, or breaker names.
5
• PMU1 A-CH-1 to PMU1 A-CH-16: These settings specify any analog data measured by the relay to be included as a
user-selectable analog channel of the data frame. Up to 16 analog channels can be configured to send any FlexAnalog
value from the relay. Examples include frequency, rate of frequency change, active and reactive power, per phase or
three-phase power, power factor, temperature via RTD inputs, and THD. The configured analog values are sampled
concurrently with the synchrophasor instant and sent as 32-bit floating-point values scaled to Engineering units.
• PMU1 A-CH-1 NM to PMU1 A-CH-16 NM: These settings allow for custom naming of the analog channels. Sixteen-
character ASCII strings are allowed as in the CHNAM field of the configuration frame.
• PMU1 D-CH-1 to PMU1 D-CH-16: These settings specify any digital flag measured by the relay to be included as a
user-selectable digital channel of the data frame. Up to sixteen digital channels can be configured to send any Flex-
Logic operand from the relay. The configured digital flags are sampled concurrently with the synchrophasor instant.
These values are mapped into a two-byte integer number, with byte 1 LSB corresponding to the digital channel 1and
byte 2 MSB corresponding to digital channel 16.
• PMU1 D-CH-1 NM to PMU1 D-CH-16 NM: These settings allow for custom naming of the digital channels. Sixteen-
character ASCII strings are allowed as in the CHNAM field of the configuration frame.
• PMU1 D-CH-1 NORMAL STATE to PMU1 D-CH-16 NORMAL STATE: These settings allow for specifying a normal
state for each digital channel. These states are transmitted in configuration frames to the data concentrator.
C37.118 PMU 1 CONFIGURATION
PATH: SETTINGS  SYSTEM SETUP PHASOR MEASUREMENT BASIC CONFIGURATION PMU 1 PMU 1 BASIC CONFIGU-
RATION 37.118 PMU 1 CONFIGURATION
 37.118 PMU 1 PMU 1 FORMAT: Range: Integer, Floating-point

 CONFIGURATION Integer Default: Integer
PMU 1 STYLE: Range: Polar, Rectangular

MESSAGE
Polar Default: Polar
PMU 1 FORMAT: This setting selects whether synchrophasors are reported as 16-bit integers or 32-bit IEEE floating point
numbers. This setting complies with bit-1 of the FORMAT field of the IEEE C37.118 configuration frame. This setting
applies to synchrophasors only; the user-selectable FlexAnalog channels are always transmitted as 16-bit integer values.

PMU 1 STYLE: This setting selects whether synchrophasors are reported in rectangular (real and imaginary) coordinates
or in polar (magnitude and angle) coordinates. This setting complies with bit-0 of the FORMAT field of the IEEE C37.118
configuration frame.
With 90-5 PMU, the FORMAT and STYLE are Floating-point and Polar respectively, as specified in the IEC 61850
standard.
NOTE
IEC 61850–90–5 PMU 1 CONFIGURATION

PATH: SETTINGS  SYSTEM SETUP PHASOR MEASUREMENT BASIC CONFIGURATION PMU1PMU 1 BASIC CONFIGURA-
TION 90 – 5 PMU 1 CONFIGURATION
 90–5 PMU 1 PMU 1 LDINST: Range: 64 char ASCII text

 CONFIGURATION PMU1 Default: blank
PMU1 LDINST: A user-defined visible string (maximum 64 char ASCII test) to assign Logical Device (LD) Inst for a PMU
LD.
As per IEC 61850-6 standard specification, the PMU LD Name is the concatenated combination (to total 64 charac-
ters) of IED Name (specified in IEC 61850 Server Settings) appended with PMU X LDINST string.
NOTE

c) CALIBRATION
PATH: SETTINGS  SYSTEM SETUP  PHASOR MEASUREMENT UNIT  PHASOR MEASUREMENT UNIT 1  PMU 1 (to 4)
CALIBRATION
 PMU 1 PMU 1 VA CALIBRATION Range: –5.00 to 5.00° in steps of 0.05

 CALIBRATION ANGLE: 0.00°
PMU 1 VA CALIBRATION Range: 95.0 to 105.0 in steps of 0.1%
MESSAGE
MAG: 100.0%
PMU 1 VB CALIBRATION Range: –5.00 to 5.00° in steps of 0.05
MESSAGE
ANGLE: 0.00°
PMU 1 VB CALIBRATION Range: 95.0 to 105.0 in steps of 0.1%
MESSAGE
MAG: 100.0%
PMU 1 VC CALIBRATION Range: –5.00 to 5.00° in steps of 0.05
MESSAGE
ANGLE: 0.00°
PMU 1 VC CALIBRATION Range: 95.0 to 105.0 in steps of 0.1%
MESSAGE
MAG: 100.0%
PMU 1 VX CALIBRATION Range: –5.00 to 5.00° in steps of 0.05
MESSAGE
ANGLE: 0.00°
PMU 1 VX CALIBRATION Range: 95.0 to 105.0 in steps of 0.1%
MESSAGE
MAG: 100.0%
PMU 1 IA CALIBRATION Range: –5.00 to 5.00° in steps of 0.05
MESSAGE
ANGLE: 0.00° 5
PMU 1 IA CALIBRATION Range: 95.0 to 105.0 in steps of 0.1%
MESSAGE
MAG: 100.0%
PMU 1 IB CALIBRATION Range: –5.00 to 5.00° in steps of 0.05
MESSAGE
ANGLE: 0.00°
PMU 1 IB CALIBRATION Range: 95.0 to 105.0 in steps of 0.1%
MESSAGE
MAG: 100.0%
PMU 1 IC CALIBRATION Range: –5.00 to 5.00° in steps of 0.05
MESSAGE
ANGLE: 0.00°
PMU 1 IC CALIBRATION Range: 95.0 to 105.0 in steps of 0.1%
MESSAGE
MAG: 100.0%
PMU 1 IG CALIBRATION Range: –5.00 to 5.00° in steps of 0.05
MESSAGE
ANGLE: 0.00°
PMU 1 IG CALIBRATION Range: 95.0 to 105.0 in steps of 0.1%
MESSAGE
MAG: 100.0%
PMU 1 SEQ VOLT SHIFT Range: –180 to 180° in steps of 30
MESSAGE
ANGLE: 0°
PMU 1 SEQ CURR SHIFT Range: –180 to 180° in steps of 30
MESSAGE
ANGLE: 0°
This menu contains user angle and magnitude calibration data for the phasor measurement unit (PMU). This data is com-
bined with the factory adjustments to shift the phasors for better accuracy.
• PMU 1 VA... IG CALIBRATION ANGLE: These settings recognize applications with protection class voltage and cur-
rent sources, and allow the user to calibrate each channel (four voltages and four currents) individually to offset errors
introduced by VTs, CTs, and cabling. The setting values are effectively added to the measured angles. Therefore, enter
a positive correction of the secondary signal lags the true signal; and negative value if the secondary signal leads the
true signal.

• PMU 1 VA... IG CALIBRATION MAGNITUDE: These settings recognize applications with protection class voltage and
current sources, and allow the user to calibrate each channel (four voltages and four currents) individually to offset
errors introduced by VTs, CTs. The setting values are effectively a multiplier of the measured magnitudes. Therefore,
enter a multiplier greater than 100% of the secondary signal increases the true signal; and a multiplier less than 100%
value of the secondary signal reduces the true signal.
• PMU 1 SEQ VOLT SHIFT ANGLE: This setting allows correcting positive- and negative-sequence voltages for vector
groups of power transformers located between the PMU voltage point, and the reference node. This angle is effectively
added to the positive-sequence voltage angle, and subtracted from the negative-sequence voltage angle. Note that:
1. When this setting is not “0°”, the phase and sequence voltages will not agree. Unlike sequence voltages, the
phase voltages cannot be corrected in a general case, and therefore are reported as measured.
2. When receiving synchrophasor data at multiple locations, with possibly different reference nodes, it can be more
beneficial to allow the central locations to perform the compensation of sequence voltages.
3. This setting applies to PMU data only. The D60 calculates symmetrical voltages independently for protection and
control purposes without applying this correction.
4. When connected to line-to-line voltages, the PMU calculates symmetrical voltages with the reference to the AG
voltage, and not to the physically connected AB voltage (see the Metering Conventions section in Chapter 6).
• PMU 1 SEQ CURR SHIFT ANGLE: This setting allows correcting positive and negative-sequence currents for vector
groups of power transformers located between the PMU current point and the reference node. The setting has the
same meaning for currents as the PMU 1 SEQ VOLT SHIFT ANGLE setting has for voltages. Normally, the two correcting
angles are set identically, except rare applications when the voltage and current measuring points are located at differ-
ent windings of a power transformer.
d) PMU TRIGGERING OVERVIEW

5 PATH: SETTINGS  SYSTEM SETUP  PHASOR...  PHASOR MEASUREMENT UNIT 1  PMU 1 TRIGGERING
 PMU 1  PMU 1 USER

See page 5-121.
 TRIGGERING  TRIGGER
 PMU 1 FREQUENCY
MESSAGE See page 5-121.
 TRIGGER
 PMU 1 VOLTAGE
 TRIGGER
 PMU 1 CURRENT
 TRIGGER
 PMU 1 POWER
 TRIGGER
 PMU 1 df/dt
 TRIGGER
Each logical phasor measurement unit (PMU) contains five triggering mechanisms to facilitate triggering of the associated
PMU recorder, or cross-triggering of other PMUs of the system. They are:
• Overfrequency and underfrequency
• Overvoltage and undervoltage
• Overcurrent
• Overpower
• High rate of change of frequency
The pre-configured triggers could be augmented with a user-specified condition built freely using programmable logic of the
relay. The entire triggering logic is refreshed once every two power system cycles.

All five triggering functions and the user-definable condition are consolidated (ORed) and connected to the PMU recorder.
Each trigger can be programmed to log its operation into the event recorder, and to signal its operation via targets. The five
triggers drive the STAT bits of the data frame to inform the destination of the synchrophasor data regarding the cause of
trigger. The following convention is adopted to drive bits 11, 3, 2, 1, and 0 of the STAT word.
Figure 5–46: STAT BITS LOGIC

The trigger reset (drop-off) timer is available for all five triggering functions (FREQ, ROCOF, VOLT, CURR, POWER) in indi-
vidual trigger settings under the TRIGGER DPO TIME setting. This asserts individual trigger operand and overall PMU x
TRIGGERED operand with stat bits 3 and 11 for a fixed interval defined by this setting. If it is required that PMU x TRIG-
GERED operand with stat bits 3 and 11 stay longer than the individual reset timer, then use the PMU x USER TRIGGER
setting assigned with appropriate elements and FlexLogic. In short, in case of USER TRIGGER, the drop-off time needs to
be implemented using FlexLogic.
e) USER TRIGGERING
PATH: SETTINGS  SYSTEM SETUP  PHASOR MEASUREMENT...  PMU 1 TRIGGERING  PMU 1 USER TRIGGER
 PMU 1 USER
 TRIGGER
PMU1 USER TRIGGER:
Off
Range: FlexLogic operands
5
The user trigger allows customized triggering logic to be constructed from FlexLogic. The entire triggering logic is refreshed
once every two power system cycles.
f) FREQUENCY TRIGGERING
PATH: SETTINGS  SYSTEM SETUP  PHASOR MEASUREMENT...  PMU 1 TRIGGERING  PMU 1 FREQUENCY TRIGGER
 PMU 1 FREQUENCY PMU 1 FREQ TRIGGER Range: Enabled, Disabled

 TRIGGER FUNCTION: Disabled
PMU 1 FREQ TRIGGER Range: 20.00 to 70.00 Hz in steps of 0.01
MESSAGE
LOW-FREQ: 49.00 Hz
PMU 1 FREQ TRIGGER Range: 20.00 to 70.00 Hz in steps of 0.01
MESSAGE
HIGH-FREQ: 61.00 Hz
PMU 1 FREQ TRIGGER Range: 0.00 to 600.00 s in steps of 0.01
MESSAGE
PKP TIME: 0.10 s
PMU 1 FREQ TRIGGER Range: 0.00 to 600.00 s in steps of 0.01
MESSAGE
DPO TIME: 1.00 s
PMU 1 FREQ TRIG BLK: Range: FlexLogic operand
MESSAGE
Off
PMU 1 FREQ TRIGGER Range: Self-Reset, Latched, Disabled
MESSAGE
TARGET: Self-Reset
PMU 1 FREQ TRIGGER Range: Enabled, Disabled
MESSAGE
EVENTS: Disabled

The trigger responds to the frequency signal of the phasor measurement unit (PMU) source. The frequency is calculated
from either phase voltages, auxiliary voltage, phase currents and ground current, in this hierarchy, depending on the source
configuration as per D60 standards. This element requires the frequency is above the minimum measurable value. If the
frequency is below this value, such as when the circuit is de-energized, the trigger drops out.
• PMU 1 FREQ TRIGGER LOW-FREQ: This setting specifies the low threshold for the abnormal frequency trigger. The
comparator applies a 0.02 Hz hysteresis.
• PMU 1 FREQ TRIGGER HIGH-FREQ: This setting specifies the high threshold for the abnormal frequency trigger. The
comparator applies a 0.02 Hz hysteresis.
• PMU 1 FREQ TRIGGER PKP TIME: This setting could be used to filter out spurious conditions and avoid unnecessary
triggering of the recorder.
• PMU 1 FREQ TRIGGER DPO TIME: This setting could be used to extend the trigger after the situation returned to nor-
mal. This setting is of particular importance when using the recorder in the forced mode (recording as long as the trig-
gering condition is asserted).
5
Figure 5–47: FREQUENCY TRIGGER SCHEME LOGIC
g) VOLTAGE TRIGGERING
PATH: SETTINGS  SYSTEM SETUP  PHASOR MEASUREMENT...  PMU 1 TRIGGERING  PMU 1 VOLTAGE TRIGGER
 PMU 1 VOLTAGE PMU 1 VOLT TRIGGER Range: Enabled, Disabled

PMU 1 VOLT TRIGGER Range: 0.250 to 1.250 pu in steps of 0.001
MESSAGE
LOW-VOLT: 0.800 pu
PMU 1 VOLT TRIGGER Range: 0.750 to 1.750 pu in steps of 0.001
MESSAGE
HIGH-VOLT: 1.200 pu
PMU 1 VOLT TRIGGER Range: 0.00 to 600.00 s in steps of 0.01
MESSAGE
PKP TIME: 0.10 s
PMU 1 VOLT TRIGGER Range: 0.00 to 600.00 s in steps of 0.01
MESSAGE
DPO TIME: 1.00 s
PMU 1 VOLT TRIG BLK: Range: FlexLogic operand
MESSAGE
Off
PMU 1 VOLT TRIGGER Range: Self-Reset, Latched, Disabled
MESSAGE
TARGET: Self-Reset
PMU 1 VOLT TRIGGER Range: Enabled, Disabled
MESSAGE
EVENTS: Disabled

This element responds to abnormal voltage. Separate thresholds are provided for low and high voltage. In terms of signal-
ing its operation, the element does not differentiate between the undervoltage and overvoltage events. The trigger
responds to the phase voltage signal of the phasor measurement unit (PMU) source. All voltage channels (A, B, and C or
AB, BC, and CA) are processed independently and could trigger the recorder. A minimum voltage supervision of 0.1 pu is
implemented to prevent pickup on a de-energized circuit, similarly to the undervoltage protection element.
• PMU 1 VOLT TRIGGER LOW-VOLT: This setting specifies the low threshold for the abnormal voltage trigger, in per-
unit of the PMU source. 1 pu is a nominal voltage value defined as the nominal secondary voltage times VT ratio. The
comparator applies a 1% hysteresis.
• PMU 1 VOLT TRIGGER HIGH-VOLT: This setting specifies the high threshold for the abnormal voltage trigger, in per-
unit of the PMU source. 1 pu is a nominal voltage value defined as the nominal secondary voltage times VT ratio. The
comparator applies a 1% hysteresis.
• PMU 1 VOLT TRIGGER PKP TIME: This setting could be used to filter out spurious conditions and avoid unnecessary
• PMU 1 VOLT TRIGGER DPO TIME: This setting could be used to extend the trigger after the situation returned to nor-
Figure 5–48: VOLTAGE TRIGGER SCHEME LOGIC
h) CURRENT TRIGGERING
PATH: SETTINGS  SYSTEM SETUP  PHASOR MEASUREMENT...  PMU 1 TRIGGERING  PMU 1 CURRENT TRIGGER
 PMU 1 CURRENT PMU 1 CURR TRIGGER Range: Enabled, Disabled

PMU 1 CURR TRIGGER Range: 0.100 to 30.000 pu in steps of 0.001
MESSAGE
PICKUP: 1.800 pu
PMU 1 CURR TRIGGER Range: 0.00 to 600.00 s in steps of 0.01
MESSAGE
PKP TIME: 0.10 s
PMU 1 CURR TRIGGER Range: 0.00 to 600.00 s in steps of 0.01
MESSAGE
DPO TIME: 1.00 s
PMU 1 CURR TRIG BLK: Range: FlexLogic operand
MESSAGE
Off
PMU 1 CURR TRIGGER Range: Self-Reset, Latched, Disabled
MESSAGE
TARGET: Self-Reset
PMU 1 CURR TRIGGER Range: Enabled, Disabled
MESSAGE
EVENTS: Disabled
This element responds to elevated current. The trigger responds to the phase current signal of the phasor measurement
unit (PMU) source. All current channel (A, B, and C) are processed independently and could trigger the recorder.

• PMU 1 CURR TRIGGER PICKUP: This setting specifies the pickup threshold for the overcurrent trigger, in per unit of
the PMU source. A value of 1 pu is a nominal primary current. The comparator applies a 3% hysteresis.
• PMU 1 CURR TRIGGER PKP TIME: This setting could be used to filter out spurious conditions and avoid unneces-
sary triggering of the recorder.
• PMU 1 CURR TRIGGER DPO TIME: This setting could be used to extend the trigger after the situation returned to nor-
Figure 5–49: CURRENT TRIGGER SCHEME LOGIC
i) POWER TRIGGERING
PATH: SETTINGS  SYSTEM SETUP  PHASOR MEASUREMENT...  PMU 1 TRIGGERING  PMU 1 POWER TRIGGER
5  PMU 1 POWER PMU 1 POWER TRIGGER Range: Enabled, Disabled
PMU 1 POWER TRIGGER Range: 0.250 to 3.000 pu in steps of 0.001
MESSAGE
ACTIVE: 1.250 pu
MESSAGE
REACTIVE: 1.250 pu
MESSAGE
APPARENT: 1.250 pu
PMU 1 POWER TRIGGER Range: 0.00 to 600.00 s in steps of 0.01
MESSAGE
PKP TIME: 0.10 s
PMU 1 POWER TRIGGER Range: 0.00 to 600.00 s in steps of 0.01
MESSAGE
DPO TIME: 1.00 s
PMU 1 PWR TRIG BLK: Range: FlexLogic operand
MESSAGE
Off
PMU 1 POWER TRIGGER Range: Self-Reset, Latched, Disabled
MESSAGE
TARGET: Self-Reset
PMU 1 POWER TRIGGER Range: Enabled, Disabled
MESSAGE
EVENTS: Disabled
This element responds to abnormal power. Separate thresholds are provided for active, reactive, and apparent powers. In
terms of signaling its operation the element does not differentiate between the three types of power. The trigger responds to
the single-phase and three-phase power signals of the phasor measurement unit (PMU) source.
• PMU 1 POWER TRIGGER ACTIVE: This setting specifies the pickup threshold for the active power of the source. For
single-phase power, 1 pu is a product of 1 pu voltage and 1 pu current, or the product of nominal secondary voltage,
the VT ratio and the nominal primary current. For the three-phase power, 1 pu is three times that for a single-phase
power in case of wye-connected VTs and 3 times in case of delta-connected VTs. The comparator applies a 3% hys-
teresis.

• PMU 1 POWER TRIGGER REACTIVE: This setting specifies the pickup threshold for the reactive power of the
source. For single-phase power, 1 pu is a product of 1 pu voltage and 1 pu current, or the product of nominal second-
ary voltage, the VT ratio and the nominal primary current. For the three-phase power, 1 pu is three times that for a sin-
gle-phase power in case of wye-connected VTs and 3 times in case of delta-connected VTs. The comparator applies
a 3% hysteresis.
• PMU 1 POWER TRIGGER APPARENT: This setting specifies the pickup threshold for the apparent power of the
source. For single-phase power, 1 pu is a product of 1 pu voltage and 1 pu current, or the product of nominal second-
ary voltage, the VT ratio and the nominal primary current. For the three-phase power, 1 pu is three times that for a sin-
gle-phase power in case of wye-connected VTs and 3 times in case of delta-connected VTs. The comparator applies
a 3% hysteresis.
• PMU 1 POWER TRIGGER PKP TIME: This setting could be used to filter out spurious conditions and avoid unneces-
sary triggering of the recorder.
• PMU 1 POWER TRIGGER DPO TIME: This setting could be used to extend the trigger after the situation returned to
normal. This setting is of particular importance when using the recorder in the forced mode (recording as long as the
triggering condition is asserted).
Figure 5–50: POWER TRIGGER SCHEME LOGIC

j) DF/DT TRIGGERING
PATH: SETTINGS  SYSTEM SETUP  PHASOR MEASUREMENT...  PMU 1 TRIGGERING  PMU 1 df/dt TRIGGER
 PMU 1 df/dt PMU 1 df/dt TRIGGER Range: Enabled, Disabled

PMU 1 df/dt TRIGGER Range: 0.10 to 15.00 Hz/s in steps of 0.01
MESSAGE
RAISE: 0.25 Hz/s
PMU 1 df/dt TRIGGER Range: 0.10 to 15.00 Hz/s in steps of 0.01
MESSAGE
FALL: 0.25 Hz/s
PMU 1 df/dt TRIGGER Range: 0.00 to 600.00 s in steps of 0.01
MESSAGE
PKP TIME: 0.10 s
PMU 1 df/dt TRIGGER Range: 0.00 to 600.00 s in steps of 0.01
MESSAGE
DPO TIME: 1.00 s
PMU 1 df/dt TRG BLK: Range: FlexLogic operand
MESSAGE
Off
PMU 1 df/dt TRIGGER Range: Self-Reset, Latched, Disabled
MESSAGE
TARGET: Self-Reset
PMU 1 df/dt TRIGGER Range: Enabled, Disabled
MESSAGE
EVENTS: Disabled
This element responds to frequency rate of change. Separate thresholds are provided for rising and dropping frequency.
5 The trigger responds to the rate of change of frequency (df/dt) of the phasor measurement unit (PMU) source.
• PMU 1 df/dt TRIGGER RAISE: This setting specifies the pickup threshold for the rate of change of frequency in the
raising direction (positive df/dt). The comparator applies a 4% hysteresis.
• PMU 1 df/dt TRIGGER FALL: This setting specifies the pickup threshold for the rate of change of frequency in the fall-
ing direction (negative df/dt). The comparator applies a 4% hysteresis.
• PMU 1 df/dt TRIGGER PKP TIME: This setting could be used to filter out spurious conditions and avoid unnecessary
• PMU 1 df/dt TRIGGER DPO TIME: This setting could be used to extend the trigger after the situation returned to nor-
FLEXLOGIC OPERANDS
PMU 1 FREQ TRIGGER
PMU 1 VOLT TRIGGER
PMU 1 CURR TRIGGER
SETTINGS PMU 1 POWER TRIGGER FLEXLOGIC OPERAND

OR
PMU 1 TRIGGERED
PMU 1 df/dt TRIGGER SETTING
FUNCTION:
PMU 1 USER TRIGGER:
Enabled = 1
Off = 0
AND
PMU 1 df/dt TRG BLK:

Off = 0
SETTINGS SETTINGS
to STAT bits of
PMU 1 df/dt TRIGGER RAISE: PMU 1 df/dt TRIGGER PKP TIME: the data frame
SETTING
PMU 1 df/dt TRIGGER FALL: PMU 1 df/dt TRIGGER DPO TIME:
PMU 1 SIGNAL FLEXLOGIC OPERAND
RUN
SOURCE: df/dt > RAISE tPKP
OR PMU 1 ROCOF TRIGGER
ROCOF, df/dt –df/dt > FALL tDPO
847000A1.CDR
Figure 5–51: RATE OF CHANGE OF FREQUENCY TRIGGER SCHEME LOGIC

k) PMU RECORDING
PATH: SETTINGS  SYSTEM SETUP  PHASOR MEASUREMENT PHASOR MEASUREMENT UNIT1  RECORDING PMU1
 PMU 1 PMU 1 FUNCTION Range: Enable, Disable

 RECORDING DISABLE
PMU 1 NO OF TIMED Range: 2 to 128 in steps of 1
MESSAGE
RECORDS: 10
PMU 1 TRIGGER MODE: Range: Automatic Overwrite, Protected
MESSAGE
AUTOMATIC OVERWRITE
PMU 1 TIMED TRIGGER Range: 1 to 50% in steps of 1
MESSAGE
POSITION: 10%
• PMU 1 FUNCTION: This setting enables or disables the recorder for PMU 1. The rate is fixed at the reporting rate set
within the aggregator (i.e., Aggregator 1).
• PMU 1 NO OF TIMED RECORDS: This setting specifies the number of timed records that are available for a given log-
ical PMU 1(4). The length of each record is equal to the available memory divided by the content size and number of
records. As the number of records is increased the available storage for each record is reduced. The relay supports a
maximum of 128 records in either timed or forced mode.
• PMU 1 TRIGGER MODE: This setting specifies what happens when the recorder uses its entire available memory
storage. Under the “Automatic Overwrite”, the last record is erased to facilitate new recording, when triggered. Under
the “Protected” selection, the recorder stops creating new records when the entire memory is used up by the old un-
cleared records.
• PMU 1 TIMED TRIGGER POSITION: This setting specifies the amount of pre-trigger data as a percent of the entire
record. This setting applies only to the timed mode of recording. 5
l) AGGREGATORS
PATH: SETTINGS  SYSTEM SETUP PHASOR MEASUREMENT UNIT PMU AGGREGATOR 1
 PMU AGGREGATOR 1 PMU AGGREGATOR 1 Range: NONE, 37.118, IEC 61850-90-5

 PROTOCOL: NONE Default: NONE
PMU AGGREGATOR 1: Range: 1 to 65534 in steps of 1

MESSAGE
IDCODE: 1 Default: 1
PMU AGGREGATOR 1 Range: No, Yes

MESSAGE
INCLUDE PMU1: No Default: No
 37.118 AGGR 1
MESSAGE See below.
 CONFIGURATION
 90-5 AGGR 1
MESSAGE See below.
 CONFIGURATION
When the protocol selection is set via the software or keypad, all aggregators whose protocol is not set to None will
be set to the last protocol saved (i.e., IEEE C37.118 or IEC 61850-90-5) to any aggregators, as both IEEE C37.118
NOTE and IEC 61850-90-5 simultaneous streaming of both R-SV values is not possible.
PATH: SETTINGS  SYSTEM SETUP PHASOR MEASUREMENT UNIT PMU AGGREGATOR 1 37.118 AGGR 1 CONFIG-
URATION
 37.118 AGGR 1 PMU AGGREGATOR 1 Range: 1 to 65534

 CONFIGURATION TCP PORT: 4712 Default: 4712
PMU AGGREGATOR 1 Range: 1 to 65534

MESSAGE
UDP PORT: 4713 Default: 4713
PMU AGGREGATOR 1 Range: Disabled, Enabled

MESSAGE
PDC CONTROL: Disabled Default: Disabled

PATH: SETTINGS  SYSTEM SETUP  PHASOR MEASUREMENT UNIT PMU AGGREGATOR 1 90-5 AGGR 1 CONFIGU-
RATION
 90-5 AGGR 1 PMU AGGREGATOR 1 Range: 56 character ASCII text

 CONFIGURATION NAME: Default: Blank
PMU AGGREGATOR1: Range: 1, 2, 3

MESSAGE
PORT: 1 Default: 1
PMU AGGREGATOR 1: Range: 1 to 65534 in steps of 1

MESSAGE
UDP PORT: 102 Default: 102
PMU AGGREGATOR 1: Range: 1 to 4

MESSAGE
NUMBER OF ASDUs: 1 Default: 1
• PMU AGGREGATOR1 PROTOCOL: This setting selects if the IEEE C37.118 or IEC 61850 standard is used.
• PMU AGGREGATOR1 IDCODE: Numeric identifier of the Aggregator / PDC function. In an IEEE C37.118 output
stream, this identifies the ID of the aggregator - which is only used if there is more than 1 PMU mapped into an aggre-
gator.
• PMU AGGREGATOR1 PMU1: If set to “Yes” aggregator 1 includes the PMU1 data set in the reporting data stream.
AGGREGATOR1 will not include PMU1 data set in the report if set to “No”.
C37.118 AGGREGATOR 1 CONFIGURATION
• PMU AGGREGATOR1: TCP PORT: This setting selects the TCP port number to be used by this aggregator for net-
work reporting. All ports, even those of unused aggregators, must be valid and unique to avoid port number collisions.
• PMU AGGREGATOR1 UDP PORT: This setting selects the UDP port number to be used by this aggregator for net-
5 work reporting. All ports, even those of unused aggregators, must be valid and unique to avoid port number collisions.
• PMU AGGREGATOR1 PDC CONTROL: The synchrophasor standard allows for user-defined controls originating at
the PDC, to be executed on the PMU. The control is accomplished via an extended command frame. The relay
decodes the first word of the extended field, EXTFRAME, to drive 16 dedicated FlexLogic operands. Each aggregator
supports 16 FlexLogic operands as shown in table 2. The operands are asserted for 5 seconds following reception of
the command frame. If the new command frame arrives within the 5 second period, the FlexLogic operands are
updated, and the 5 second timer is re-started. This setting enables or disables the control. When enabled, all 16 oper-
ands for each aggregator are active; when disabled all 16 operands for each aggregator remain reset.
Table 5–12: FLEXLOGIC OPERANDS SUPPORTED BY AGGREGATOR
OPERAND TYPE OPERAND SYNTAX OPERAND DESCRIPTION
ELEMENT: AGTR1 PDC CNTRL 1 Phasor data concentrator asserts control bit 1, as
Synchrophasor, phasor data, received via the network.
concentrator
as above AGTR1 PDC CNTRL 2 Phasor data concentrator asserts control bit 2 as
received via the network.

as above AGTR1 PDC CNTRL 16 Phasor data concentrator asserts control bit 16, as
received via the network
received via the network

as above AGTR1 PDC CNTRL 16 Phasor data concentrator asserts control bit 16, as

IEC61850-90-5 AGGREGATOR 1 CONFIGURATION

• PMU AGGREGATOR1: NAME: A user-defined visible string of characters (max. 56) to identify the source of the
stream. This value, concatenated with the Aggregator IDCode and Aggregator Class of Service, is mapped into the
IEC61850 MSVID filed in the output stream.
• AGGREGATOR1: PHYSICAL PORT: This setting determines which physical ports through which the synchrophasor
traffic will be transmitted. The range is 1, 2, 3.
• PMU AGGREGATOR1: UDP: This setting selects the UDP port number that is used by this dataset for network report-
ing. Default setting values for IEEE C37.118 and IEC 6150-90-5 are provided.
• PMU AGGREGATOR1: #OF ASDUs: This setting sets the number of ASDU’s per from 1 through to 4. Refer to the
table below.
Table 5–13: # OF ASDU
SETTINGS FOR # OF ASDU TRANSMISSION
1 ASDU at T0 (current values)
2 ASDU at T-1 (previous values) + ASDU at T0 (current values)
3 values)+ ASDU at T-2 (previous values) + ASDU at T-1 (previous ASDU at T0 (current
values)
4 ASDU at T-3 (previous values) + ASDU at T-2 (previous values) + ASDU at T-1 (previous
values)+ASDU at T0 (current values)
m) CONTROL BLOCKS
PATH: SETTINGS  SYSTEM SETUP PHASOR MEASUREMENT UNIT IEC 90 – 5 MSVCB01 CONFIGURATION
 IEC 90-5 MSVCB MSVCB 1 SVENA: Range: FlexLogic operand

 CONFIGURATION OFF Default: Off 5
MSVCB 1 CLIENT CTRL: Range: FlexLogic operand
MESSAGE
OFF Default: Off
MSVCB 1 SVENA DEFLT: Range: FlexLogic operand

MESSAGE Default: Off
OFF
MSVCB 1 CONFREV: Range: 1 to 4294967295

MESSAGE
1 Default: 1
MSVCB 1 PRIORITY: Range: 0 to 7

MESSAGE
4 Default: 4
MSVCB 1 IP CLASS: Range: 0 to 252

MESSAGE
46 Default: 46
MSVCB 1 VID: Range: 0 to 4095

MESSAGE
0 Default: 0
MSVCB 1 APPID: Range: 0 to 16383

MESSAGE
0 Default: 0
MSVCB 1 DEST. IP: Range: 0 to 255.255.255.255

MESSAGE
224.0.0.0 Default: 224.0.0.0
MSVCB 1 SECURITY: Range: 0 to 2

MESSAGE
0 Default: 0
• MSVCB 1 SVENA: The SV Stream Control is set by either toggling an assigned FlexLogic operand or a remote client
write, to start and stop the streaming of R-SV frames. If remote client control is disabled, a negative response is pro-
vided to the client in response to a write attempt. A FlexLogic operand (SvEna) is provided for each Aggregator that

reflects the state of the SvEna control where “1”= Enabled and “0”=Disabled. The logic for setting the SvEna control bit
is shown in the following figure.
Figure 5–52: LOGIC FOR SETTING SVENA CONTROL BIT

• MSVCB 1 Client CONTRL: This setting determines if a client can write to the reserve bit. When the assigned Flex-
Logic operand is a logic 1 state, remote clients can write to both the reserve bit and the SvEna bit. When the FlexLogic
operand is a logic 0 state, the remote client writes to the reserve bit, the SvEna is rejected by the UR, and a negative
response with the appropriate Service Error is returned to the client.
5 • MSVCB 1 SVENA Default: This setting sets the default state of the stream (On or Off) on power-up or restart.
• MSVCB 1 CONFREV: The relay increments the Configuration revision every time the configuration is changed. This
setting allows the user to reset the configuration back to 1 or a value from 1 to 4294967295.
• MSVCB 1 PRIORITY: A value from 0 through 7: The default value is 4.
• MSVCB 1 IP Class: The value represents the IPv4 Differentiated Services (formerly called TypeOfService) value. The
default value is set for Expedited Forwarding (101110B (46 or 2EH). This value provides priority routing, when sup-
ported in the routers.
• MSVCB 1 VID: A range of values limited from 0 to 4095.
• MSVCB 1 APPID: This setting allows the selection of a specific application ID for each sending device.
• MSVCB 1 DEST IP Address: This is the destination multicast address IP address that is entered in Standard IPV4
address format. The valid range for IPv4 is from 224.0.0.0 to 239.255.255.255, but the UR does not test the address
entered.
• MSVCB 1 Security: This setting selects the level of security and authentication used, as outlined in the following table,
and is in the form of an enumeration as per standard. The range is 0 to 2.
Shaded settings in the table are not supported in firmware 7.0.
NOTE ENUMERATION AUTHENTICATION ENCRYPTION

0 no no
1 yes no
2 yes yes

5 SETTINGS 5.5 FLEXLOGIC
5.5FLEXLOGIC 5.5.1 INTRODUCTION TO FLEXLOGIC
To provide maximum flexibility to the user, the arrangement of internal digital logic combines fixed and user-programmed
parameters. Logic upon which individual features are designed is fixed, and all other logic, from digital input signals through
elements or combinations of elements to digital outputs, is variable. The user has complete control of all variable logic
through FlexLogic. In general, the system receives analog and digital inputs which it uses to produce analog and digital out-
puts. The major sub-systems of a generic UR-series relay involved in this process are shown below.
Figure 5–53: UR ARCHITECTURE OVERVIEW

The states of all digital signals used in the D60 are represented by flags (or FlexLogic operands, which are described later
in this section). A digital “1” is represented by a 'set' flag. Any external contact change-of-state can be used to block an ele-
ment from operating, as an input to a control feature in a FlexLogic equation, or to operate a contact output. The state of the
contact input can be displayed locally or viewed remotely via the communications facilities provided. If a simple scheme
where a contact input is used to block an element is desired, this selection is made when programming the element. This
capability also applies to the other features that set flags: elements, virtual inputs, remote inputs, schemes, and human
operators.
If more complex logic than presented above is required, it is implemented via FlexLogic. For example, if it is desired to have
the closed state of contact input H7a and the operated state of the phase undervoltage element block the operation of the
phase time overcurrent element, the two control input states are programmed in a FlexLogic equation. This equation ANDs
the two control inputs to produce a virtual output which is then selected when programming the phase time overcurrent to
be used as a blocking input. Virtual outputs can only be created by FlexLogic equations.
Traditionally, protective relay logic has been relatively limited. Any unusual applications involving interlocks, blocking, or
supervisory functions had to be hard-wired using contact inputs and outputs. FlexLogic minimizes the requirement for aux-
iliary components and wiring while making more complex schemes possible.

5.5 FLEXLOGIC 5 SETTINGS
The logic that determines the interaction of inputs, elements, schemes and outputs is field programmable through the use
of logic equations that are sequentially processed. The use of virtual inputs and outputs in addition to hardware is available
internally and on the communication ports for other relays to use (distributed FlexLogic).
FlexLogic allows users to customize the relay through a series of equations that consist of operators and operands. The
operands are the states of inputs, elements, schemes and outputs. The operators are logic gates, timers and latches (with
set and reset inputs). A system of sequential operations allows any combination of specified operands to be assigned as
inputs to specified operators to create an output. The final output of an equation is a numbered register called a virtual out-
put. Virtual outputs can be used as an input operand in any equation, including the equation that generates the output, as a
seal-in or other type of feedback.
A FlexLogic equation consists of parameters that are either operands or operators. Operands have a logic state of 1 or 0.
Operators provide a defined function, such as an AND gate or a Timer. Each equation defines the combinations of parame-
ters to be used to set a Virtual Output flag. Evaluation of an equation results in either a 1 (=ON, i.e. flag set) or 0 (=OFF, i.e.
flag not set). Each equation is evaluated at least 4 times every power system cycle.
Some types of operands are present in the relay in multiple instances; e.g. contact and remote inputs. These types of oper-
ands are grouped together (for presentation purposes only) on the faceplate display. The characteristics of the different
types of operands are listed in the table below.
Table 5–14: D60 FLEXLOGIC OPERAND TYPES

OPERAND TYPE STATE EXAMPLE FORMAT CHARACTERISTICS
[INPUT IS ‘1’ (= ON) IF...]
Contact Input On Cont Ip On Voltage is presently applied to the input (external contact
closed).
Off Cont Ip Off Voltage is presently not applied to the input (external
contact open).
5 Contact Output
(type Form-A contact
Current On Cont Op 1 Ion Current is flowing through the contact.
only) Voltage On Cont Op 1 VOn Voltage exists across the contact.

Voltage Off Cont Op 1 VOff Voltage does not exists across the contact.
Direct Input On DIRECT INPUT 1 On The direct input is presently in the ON state.
Element Pickup PHASE TOC1 PKP The tested parameter is presently above the pickup setting
(Analog) of an element which responds to rising values or below the
pickup setting of an element which responds to falling
values.
Dropout PHASE TOC1 DPO This operand is the logical inverse of the above PKP
operand.
Operate PHASE TOC1 OP The tested parameter has been above/below the pickup
setting of the element for the programmed delay time, or
has been at logic 1 and is now at logic 0 but the reset timer
has not finished timing.
Block PHASE TOC1 BLK The output of the comparator is set to the block function.
Element Pickup Dig Element 1 PKP The input operand is at logic 1.
(Digital)
Dropout Dig Element 1 DPO This operand is the logical inverse of the above PKP
operand.
Operate Dig Element 1 OP The input operand has been at logic 1 for the programmed
pickup delay time, or has been at logic 1 for this period and
is now at logic 0 but the reset timer has not finished timing.
Element Higher than Counter 1 HI The number of pulses counted is above the set number.
(Digital Counter)
Equal to Counter 1 EQL The number of pulses counted is equal to the set number.
Lower than Counter 1 LO The number of pulses counted is below the set number.
Fixed On On Logic 1
Off Off Logic 0
Remote Input On REMOTE INPUT 1 On The remote input is presently in the ON state.
Virtual Input On Virt Ip 1 On The virtual input is presently in the ON state.
Virtual Output On Virt Op 1 On The virtual output is presently in the set state (i.e.
evaluation of the equation which produces this virtual
output results in a "1").

The operands available for this relay are listed alphabetically by types in the following table.
Table 5–15: D60 FLEXLOGIC OPERANDS (Sheet 1 of 11)
CONTROL CONTROL PUSHBTN 1 ON Control pushbutton 1 is being pressed
PUSHBUTTONS CONTROL PUSHBTN 2 ON Control pushbutton 2 is being pressed
CONTROL PUSHBTN 3 ON Control pushbutton 3 is being pressed
DIRECT DEVICES DIRECT DEVICE 1On Flag is set, logic=1
 
DIRECT DEVICE 16On Flag is set, logic=1
DIRECT DEVICE 1Off Flag is set, logic=1
 
DIRECT DEVICE 16Off Flag is set, logic=1
DIRECT INPUT/ DIR IO CH1 CRC ALARM The rate of direct input messages received on channel 1 and failing the CRC
OUTPUT exceeded the user-specified level.
CHANNEL DIR IO CH2 CRC ALARM The rate of direct input messages received on channel 2 and failing the CRC
MONITORING exceeded the user-specified level.
DIR IO CH1 UNRET ALM The rate of returned direct input/output messages on channel 1 exceeded the
user-specified level (ring configurations only).
DIR IO CH2 UNRET ALM The rate of returned direct input/output messages on channel 2 exceeded the
user-specified level (ring configurations only).
ELEMENT: AR ENABLED Autoreclosure is enabled and ready to perform
Autoreclose AR DISABLED Autoreclosure is disabled
(1P/3P) AR RIP Autoreclosure is in “reclose-in-progress” state
AR 1-P RIP A single-pole reclosure is in progress
AR 3-P/1 RIP A three-pole reclosure is in progress, via dead time 1
AR 3-P/4 RIP
AR LO
A three-pole reclosure is in progress, via dead time 4
Autoreclosure is in lockout state
5
AR BKR1 BLK Reclosure of breaker 1 is blocked
AR BKR2 BLK Reclosure of breaker 2 is blocked
AR CLOSE BKR1 Reclose breaker 1 signal
AR CLOSE BKR2 Reclose breaker 2 signal
AR FORCE 3-P TRIP Force any trip to a three-phase trip
AR SHOT CNT > 0 The first ‘CLOSE BKR X’ signal has been issued
AR SHOT CNT = 1 Shot count is equal to 1
AR MODE = 1 Autoreclose mode equal to 1 (1 and 3 pole mode)
AR MODE = 2 Autoreclose mode equal to 2 (1 pole mode)
AR MODE = 3 Autoreclose mode equal to 3 (3 pole-A mode)
AR MODE = 4 Autoreclose mode equal to 4 (3 pole-B mode)
AR MODE SWITCH FAIL Autoreclose mode switching is attempted, but failed
AR ZONE 1 EXTENT The zone 1 distance function must be set to the extended overreach value
AR INCOMPLETE SEQ The incomplete sequence timer timed out
AR RESET Autoreclose has been reset either manually or by the reset timer
ELEMENT: AUX OV1 PKP Auxiliary overvoltage element has picked up
Auxiliary AUX OV1 DPO Auxiliary overvoltage element has dropped out
overvoltage AUX OV1 OP Auxiliary overvoltage element has operated
AUX OV2 to AUX OV3 Same set of operands as shown for AUX OV1
ELEMENT: AUX UV1 PKP Auxiliary undervoltage element has picked up
Auxiliary AUX UV1 DPO Auxiliary undervoltage element has dropped out
undervoltage AUX UV1 OP Auxiliary undervoltage element has operated
AUX UV2 to AUX UV3 Same set of operands as shown for AUX UV1
ELEMENT BKR 1 FLSHOVR PKP A Breaker 1 flashover element phase A has picked up
Breaker flashover BKR 1 FLSHOVR PKP B Breaker 1 flashover element phase B has picked up
BKR 1 FLSHOVR PKP C Breaker 1 flashover element phase C has picked up
BKR 1 FLSHOVR PKP Breaker 1 flashover element has picked up
BKR 1 FLSHOVR OP A Breaker 1 flashover element phase A has operated
BKR 1 FLSHOVR OP B Breaker 1 flashover element phase B has operated
BKR 1 FLSHOVR OP C Breaker 1 flashover element phase C has operated
BKR 1 FLSHOVR OP Breaker 1 flashover element has operated
BKR 1 FLSHOVR DPO A Breaker 1 flashover element phase A has dropped out
BKR 1 FLSHOVR DPO B Breaker 1 flashover element phase B has dropped out
BKR 1 FLSHOVR DPO C Breaker 1 flashover element phase C has dropped out
BKR 1 FLSHOVR DPO Breaker 1 flashover element has dropped out
BKR 2 FLSHOVR... Same set of operands as shown for BKR 1 FLSHOVR


ELEMENT: BKR ARC 1 OP Breaker arcing current 1 has operated
Breaker arcing BKR ARC 2 OP Breaker arcing current 2 has operated
ELEMENT BKR FAIL 1 RETRIPA Breaker failure 1 re-trip phase A (only for 1-pole schemes)
Breaker failure BKR FAIL 1 RETRIPB Breaker failure 1 re-trip phase B (only for 1-pole schemes)
BKR FAIL 1 RETRIPC Breaker failure 1 re-trip phase C (only for 1-pole schemes)
BKR FAIL 1 RETRIP Breaker failure 1 re-trip 3-phase
BKR FAIL 1 T1 OP Breaker failure 1 timer 1 is operated
BKR FAIL 1 TRIP OP Breaker failure 1 trip is operated
BKR FAIL 2... Same set of operands as shown for BKR FAIL 1
ELEMENT BRK RESTRIKE 1 OP Breaker restrike detected in any phase of the breaker control 1 element.
Breaker restrike BRK RESTRIKE 1 OP A Breaker restrike detected in phase A of the breaker control 1 element.
BRK RESTRIKE 1 OP B Breaker restrike detected in phase B of the breaker control 1 element.
BRK RESTRIKE 1 OP C Breaker restrike detected in phase C of the breaker control 1 element.
BKR RESTRIKE 2... Same set of operands as shown for BKR RESTRIKE 1
ELEMENT: BREAKER 1 OFF CMD Breaker 1 open command initiated
Breaker control BREAKER 1 ON CMD Breaker 1 close command initiated
BREAKER 1 A BAD ST Breaker 1 phase A bad status is detected (discrepancy between
the 52/a and 52/b contacts)
BREAKER 1 A INTERM Breaker 1 phase A intermediate status is detected (transition from one
position to another)
BREAKER 1 A CLSD Breaker 1 phase A is closed
BREAKER 1 A OPEN Breaker 1 phase A is open
BREAKER 1 B BAD ST Breaker 1 phase B bad status is detected (discrepancy between
BREAKER 1 B INTERM Breaker 1 phase B intermediate status is detected (transition from one
5 BREAKER 1 B CLSD
BREAKER 1 B OPEN
BREAKER 1 C BAD ST
Breaker 1 phase B is closed
Breaker 1 phase B is open
Breaker 1 phase C bad status is detected (discrepancy between
BREAKER 1 C INTERM Breaker 1 phase C intermediate status is detected (transition from one
BREAKER 1 C CLSD Breaker 1 phase C is closed
BREAKER 1 C OPEN Breaker 1 phase C is open
BREAKER 1 BAD STATUS Breaker 1 bad status is detected on any pole
BREAKER 1 CLOSED Breaker 1 is closed
BREAKER 1 OPEN Breaker 1 is open
BREAKER 1 DISCREP Breaker 1 has discrepancy
BREAKER 1 TROUBLE Breaker 1 trouble alarm
BREAKER 1 MNL CLS Breaker 1 manual close
BREAKER 1 TRIP A Breaker 1 trip phase A command
BREAKER 1 TRIP B Breaker 1 trip phase B command
BREAKER 1 TRIP C Breaker 1 trip phase C command
BREAKER 1 ANY P OPEN At least one pole of breaker 1 is open
BREAKER 1 ONE P OPEN Only one pole of breaker 1 is open
BREAKER 1 OOS Breaker 1 is out of service
BREAKER 2... Same set of operands as shown for BREAKER 1
ELEMENT: BROKEN CONDUCT 1 OP Asserted when the broken conductor 1 element operates
Broken conductor BROKEN CONDUCT 1 PKP Asserted when the broken conductor 1 element picks up
BROKEN CONDUCT 2... Same set of operands as shown for BROKEN CONDUCTOR 1
ELEMENT: COMP OV STG1 PKP Asserted when the compensated overvoltage element picks up in stage 1
Compensated COMP OV STG2 PKP Asserted when the compensated overvoltage element picks up in stage 2
overvoltage COMP OV STG3 PKP Asserted when the compensated overvoltage element picks up in stage 3
COMP OV STG1 DPO Asserted when the compensated overvoltage element drops out in stage 1
COMP OV STG1 OP Asserted when the compensated overvoltage element operates in stage 1
COMP OV PKP Asserted when the compensated overvoltage element picks up
COMP OV DPO Asserted when the compensated overvoltage element drops out
COMP OV OP Asserted when the compensated overvoltage element operates
ELEMENT: Counter 1 HI Digital counter 1 output is ‘more than’ comparison value
Digital counters Counter 1 EQL Digital counter 1 output is ‘equal to’ comparison value
Counter 1 LO Digital counter 1 output is ‘less than’ comparison value
Counter 2 to Counter 8 Same set of operands as shown for Counter 1


ELEMENT: DCUB TX1 Directional comparison unblocking scheme asserts transmit bit 1
Directional DCUB TX2 Directional comparison unblocking scheme asserts transmit bit 2
comparison DCUB TX3 Directional comparison unblocking scheme asserts transmit bit 3
unblocking scheme DCUB TX4 Directional comparison unblocking scheme asserts transmit bit 4
DCUB TRIP A Directional comparison unblocking scheme has operated to trip phase A
DCUB TRIP B Directional comparison unblocking scheme has operated to trip phase B
DCUB TRIP C Directional comparison unblocking scheme has operated to trip phase C
DCUB TRIP 3P Directional comparison unblocking scheme has operated to trip all phases
DCUB OP Directional comparison unblocking scheme has operated.
ELEMENT: Dig Element 1 PKP Digital Element 1 is picked up
Digital elements Dig Element 1 OP Digital Element 1 is operated
Dig Element 1 DPO Digital Element 1 is dropped out
Dig Element 2 to Dig Element 48 Same set of operands as shown for Dig Element 1
ELEMENT: DIR BLOCK TX INIT Directional blocking signal is initiated
Blocking scheme DIR BLOCK TX1 STOP Directional blocking scheme de-asserts transmit bit no. 1
DIR BLOCK TX2 STOP Directional blocking scheme de-asserts transmit bit no. 2
DIR BLOCK TRIP A Directional blocking scheme has operated to trip phase A
DIR BLOCK TRIP B Directional blocking scheme has operated to trip phase B
DIR BLOCK TRIP C Directional blocking scheme has operated to trip phase C
DIR BLOCK TRIP 3P Directional blocking scheme has tripped all 3 phases
DIR BLOCK OP Directional blocking scheme has operated
ELEMENT: DIR POWER 1 STG1 PKP Stage 1 of the directional power element 1 has picked up
Sensitive directional DIR POWER 1 STG2 PKP Stage 2 of the directional power element 1 has picked up
power DIR POWER 1 STG1 DPO Stage 1 of the directional power element 1 has dropped out
DIR POWER 1 STG2 DPO Stage 2 of the directional power element 1 has dropped out
DIR POWER 1 STG1 OP Stage 1 of the directional power element 1 has operated
DIR POWER 1 STG2 OP Stage 2 of the directional power element 1 has operated
DIR POWER 1 PKP
DIR POWER 1 DPO
The directional power element has picked up
The directional power element has dropped out 5
DIR POWER 1 OP The directional power element has operated
DIR POWER 2 Same set of operands as DIR POWER 1
ELEMENT: DUTT TX1 Direct under-reaching transfer trip asserts transmit bit 1
DUTT DUTT TX2 Direct under-reaching transfer trip asserts transmit bit 2
(Direct underreach DUTT TX3 Direct under-reaching transfer trip asserts transmit bit 3
transfer trip) DUTT TX4 Direct under-reaching transfer trip asserts transmit bit 4
DUTT TRIP A Direct under-reaching transfer trip has operated to trip phase A
DUTT TRIP B Direct under-reaching transfer trip has operated to trip phase B
DUTT TRIP C Direct under-reaching transfer trip has operated to trip phase C
DUTT TRIP 3P Direct under-reaching transfer trip has operated to trip all three phases
DUTT OP Direct under-reaching transfer trip has operated
ELEMENT FREQ RATE 1 PKP The frequency rate of change 1 element has picked up
Frequency rate of FREQ RATE 1 DPO The frequency rate of change 1 element has dropped out
change FREQ RATE 1 OP The frequency rate of change 1 element has operated
FREQ RATE 2 to FREQ RATE 4 Same set of operands as shown for FREQ RATE 1
ELEMENT: FxE 1 PKP FlexElement 1 has picked up
FlexElements FxE 1 OP FlexElement 1 has operated
FxE 1 DPO FlexElement 1 has dropped out
FxE 2 to FxE 8 Same set of operands as shown for FxE 1
ELEMENT: GND DIST Z1 PKP Ground distance zone 1 has picked up
Ground distance GND DIST Z1 OP Ground distance zone 1 has operated
GND DIST Z1 OP A Ground distance zone 1 phase A has operated
GND DIST Z1 OP B Ground distance zone 1 phase B has operated
GND DIST Z1 OP C Ground distance zone 1 phase C has operated
GND DIST Z1 PKP A Ground distance zone 1 phase A has picked up
GND DIST Z1 PKP B Ground distance zone 1 phase B has picked up
GND DIST Z1 PKP C Ground distance zone 1 phase C has picked up
GND DIST Z1 SUPN IN Ground distance zone 1 neutral is supervising
GND DIST Z1 DPO A Ground distance zone 1 phase A has dropped out
GND DIST Z1 DPO B Ground distance zone 1 phase B has dropped out
GND DIST Z1 DPO C Ground distance zone 1 phase C has dropped out
GND DIST Z2 DIR SUPN Ground distance zone 2 directional is supervising
GND DIST Z2 to Z5 Same set of operands as shown for GND DIST Z1
ELEMENT: GROUND IOC1 PKP Ground instantaneous overcurrent 1 has picked up
Ground GROUND IOC1 OP Ground instantaneous overcurrent 1 has operated
instantaneous GROUND IOC1 DPO Ground instantaneous overcurrent 1 has dropped out
overcurrent
GROUND IOC2 Same set of operands as shown for GROUND IOC 1


ELEMENT: GROUND TOC1 PKP Ground time overcurrent 1 has picked up
Ground time GROUND TOC1 OP Ground time overcurrent 1 has operated
overcurrent GROUND TOC1 DPO Ground time overcurrent 1 has dropped out
GROUND TOC2 Same set of operands as shown for GROUND TOC1
ELEMENT: HYBRID POTT TX1 Hybrid permissive over-reaching transfer trip asserts transmit bit 1
Hybrid POTT HYBRID POTT TX2 Hybrid permissive over-reaching transfer trip asserts transmit bit 2
(Hybrid permissive HYBRID POTT TX3 Hybrid permissive over-reaching transfer trip asserts transmit bit 3
overreach transfer HYBRID POTT TX4 Hybrid permissive over-reaching transfer trip asserts transmit bit 4
trip) HYBRID POTT TRIP A Hybrid permissive over-reaching transfer trip has operated to trip phase A
HYBRID POTT TRIP B Hybrid permissive over-reaching transfer trip has operated to trip phase B
HYBRID POTT TRIP C Hybrid permissive over-reaching transfer trip has operated to trip phase C
HYBRID POTT TRIP 3P Hybrid permissive over-reaching transfer trip has tripped all three phases
HYBRID POTT OP Hybrid permissive over-reaching transfer trip has operated
ELEMENT LATCH 1 ON Non-volatile latch 1 is ON (Logic = 1)
Non-volatile latches LATCH 1 OFF Non-volatile latch 1 is OFF (Logic = 0)
LATCH 2 to LATCH 16 Same set of operands as shown for LATCH 1
ELEMENT: LINE PICKUP OP Line pickup has operated
Line pickup LINE PICKUP PKP Line pickup has picked up
LINE PICKUP DPO Line pickup has dropped out
LINE PICKUP I<A Line pickup detected phase A current below 5% of nominal
LINE PICKUP I<B Line pickup detected phase B current below 5% of nominal
LINE PICKUP I<C Line pickup detected phase C current below 5% of nominal
LINE PICKUP UV PKP Line pickup undervoltage has picked up
LINE PICKUP LEO PKP Line pickup line end open has picked up
LINE PICKUP RCL TRIP Line pickup operated from overreaching zone 2 when reclosing the line
(zone 1 extension functionality)
ELEMENT: LOAD ENCHR PKP Load encroachment has picked up
Load encroachment LOAD ENCHR OP Load encroachment has operated
5 LOAD ENCHR DPO Load encroachment has dropped out
ELEMENT: NEG SEQ DIR OC1 FWD Negative-sequence directional overcurrent 1 forward has operated
Negative-sequence NEG SEQ DIR OC1 REV Negative-sequence directional overcurrent 1 reverse has operated
directional NEG SEQ DIR OC2 FWD Negative-sequence directional overcurrent 2 forward has operated
overcurrent NEG SEQ DIR OC2 REV Negative-sequence directional overcurrent 2 reverse has operated
ELEMENT: NEG SEQ IOC1 PKP Negative-sequence instantaneous overcurrent 1 has picked up
Negative-sequence NEG SEQ IOC1 OP Negative-sequence instantaneous overcurrent 1 has operated
instantaneous NEG SEQ IOC1 DPO Negative-sequence instantaneous overcurrent 1 has dropped out
overcurrent
NEG SEQ IOC2 Same set of operands as shown for NEG SEQ IOC1
ELEMENT: NEG SEQ OV1 PKP Negative-sequence overvoltage element has picked up
Negative-sequence NEG SEQ OV1 DPO Negative-sequence overvoltage element has dropped out
overvoltage NEG SEQ OV1 OP Negative-sequence overvoltage element has operated
NEG SEQ OV2... Same set of operands as shown for NEG SEQ OV1
ELEMENT: NEG SEQ TOC1 PKP Negative-sequence time overcurrent 1 has picked up
Negative-sequence NEG SEQ TOC1 OP Negative-sequence time overcurrent 1 has operated
time overcurrent NEG SEQ TOC1 DPO Negative-sequence time overcurrent 1 has dropped out
NEG SEQ TOC2 Same set of operands as shown for NEG SEQ TOC1
ELEMENT: NEUTRAL IOC1 PKP Neutral instantaneous overcurrent 1 has picked up
Neutral NEUTRAL IOC1 OP Neutral instantaneous overcurrent 1 has operated
instantaneous NEUTRAL IOC1 DPO Neutral instantaneous overcurrent 1 has dropped out
overcurrent
NEUTRAL IOC2 Same set of operands as shown for NEUTRAL IOC1
ELEMENT: NEUTRAL OV1 PKP Neutral overvoltage element 1 has picked up
Neutral overvoltage NEUTRAL OV1 DPO Neutral overvoltage element 1 has dropped out
NEUTRAL OV1 OP Neutral overvoltage element 1 has operated
ELEMENT: NEUTRAL TOC1 PKP Neutral time overcurrent 1 has picked up
Neutral time NEUTRAL TOC1 OP Neutral time overcurrent 1 has operated
overcurrent NEUTRAL TOC1 DPO Neutral time overcurrent 1 has dropped out
NEUTRAL TOC2 Same set of operands as shown for NEUTRAL TOC1
ELEMENT: NTRL DIR OC1 FWD Neutral directional overcurrent 1 forward has operated
Neutral directional NTRL DIR OC1 REV Neutral directional overcurrent 1 reverse has operated
overcurrent
NTRL DIR OC2 Same set of operands as shown for NTRL DIR OC1


ELEMENT: OPEN POLE OP ФA Open pole condition is detected in phase A
Open pole detector OPEN POLE OP ФB Open pole condition is detected in phase B
OPEN POLE OP ФC Open pole condition is detected in phase C
OPEN POLE BKR ФA OP Based on the breaker(s) auxiliary contacts, an open pole condition is
detected on phase A
OPEN POLE BKR ФB OP Based on the breaker(s) auxiliary contacts, an open pole condition is
detected on phase B
OPEN POLE BKR ФC OP Based on the breaker(s) auxiliary contacts, an open pole condition is
detected on phase C
OPEN POLE BLK N Blocking signal for neutral, ground, and negative-sequence overcurrent
element is established
OPEN POLE BLK AB Blocking signal for the AB phase distance elements is established
OPEN POLE BLK BC Blocking signal for the BC phase distance elements is established
OPEN POLE BLK CA Blocking signal for the CA phase distance elements is established
OPEN POLE REM OP ФA Remote open pole condition detected in phase A
OPEN POLE REM OP ФB Remote open pole condition detected in phase B
OPEN POLE REM OP ФC Remote open pole condition detected in phase C
OPEN POLE OP Open pole detector is operated
OPEN POLE I< ФA Open pole undercurrent condition is detected in phase A
OPEN POLE I< ФB Open pole undercurrent condition is detected in phase B
OPEN POLE I< ФC Open pole undercurrent condition is detected in phase C
ELEMENT: OVERFREQ 1 PKP Overfrequency 1 has picked up
Overfrequency OVERFREQ 1 OP Overfrequency 1 has operated
OVERFREQ 1 DPO Overfrequency 1 has dropped out
OVERFREQ 2 to 4 Same set of operands as shown for OVERFREQ 1
ELEMENT: PDC NETWORK CNTRL 1 Phasor data concentrator asserts control bit 1 as received via the network
Synchrophasor PDC NETWORK CNTRL 2 Phasor data concentrator asserts control bit 2 as received via the network
phasor data  
concentrator PDC NETWORK CNTRL 16 Phasor data concentrator asserts control bit 16 as received via the network
ELEMENT:
Phase directional
PH DIR1 BLK A
PH DIR1 BLK B
Phase A directional 1 block
Phase B directional 1 block 5
overcurrent PH DIR1 BLK C Phase C directional 1 block
PH DIR1 BLK Phase directional 1 block
PH DIR2 Same set of operands as shown for PH DIR1
ELEMENT: PH DIST Z1 PKP Phase distance zone 1 has picked up
Phase distance PH DIST Z1 OP Phase distance zone 1 has operated
PH DIST Z1 OP AB Phase distance zone 1 phase AB has operated
PH DIST Z1 OP BC Phase distance zone 1 phase BC has operated
PH DIST Z1 OP CA Phase distance zone 1 phase CA has operated
PH DIST Z1 PKP AB Phase distance zone 1 phase AB has picked up
PH DIST Z1 PKP BC Phase distance zone 1 phase BC has picked up
PH DIST Z1 PKP CA Phase distance zone 1 phase CA has picked up
PH DIST Z1 SUPN IAB Phase distance zone 1 phase AB IOC is supervising
PH DIST Z1 SUPN IBC Phase distance zone 1 phase BC IOC is supervising
PH DIST Z1 SUPN ICA Phase distance zone 1 phase CA IOC is supervising
PH DIST Z1 DPO AB Phase distance zone 1 phase AB has dropped out
PH DIST Z1 DPO BC Phase distance zone 1 phase BC has dropped out
PH DIST Z1 DPO CA Phase distance zone 1 phase CA has dropped out
PH DIST Z2 to Z5 Same set of operands as shown for PH DIST Z1
ELEMENT: PHASE IOC1 PKP At least one phase of phase instantaneous overcurrent 1 has picked up
Phase PHASE IOC1 OP At least one phase of phase instantaneous overcurrent 1 has operated
instantaneous PHASE IOC1 DPO All phases of phase instantaneous overcurrent 1 have dropped out
overcurrent PHASE IOC1 PKP A Phase A of phase instantaneous overcurrent 1 has picked up
PHASE IOC1 PKP B Phase B of phase instantaneous overcurrent 1 has picked up
PHASE IOC1 PKP C Phase C of phase instantaneous overcurrent 1 has picked up
PHASE IOC1 OP A Phase A of phase instantaneous overcurrent 1 has operated
PHASE IOC1 OP B Phase B of phase instantaneous overcurrent 1 has operated
PHASE IOC1 OP C Phase C of phase instantaneous overcurrent 1 has operated
PHASE IOC1 DPO A Phase A of phase instantaneous overcurrent 1 has dropped out
PHASE IOC1 DPO B Phase B of phase instantaneous overcurrent 1 has dropped out
PHASE IOC1 DPO C Phase C of phase instantaneous overcurrent 1 has dropped out
PHASE IOC2 and higher Same set of operands as shown for PHASE IOC1


ELEMENT: PHASE OV1 PKP At least one phase of overvoltage 1 has picked up
Phase overvoltage PHASE OV1 OP At least one phase of overvoltage 1 has operated
PHASE OV1 DPO All phases of overvoltage 1 have dropped out
PHASE OV1 PKP A Phase A of overvoltage 1 has picked up
PHASE OV1 PKP B Phase B of overvoltage 1 has picked up
PHASE OV1 PKP C Phase C of overvoltage 1 has picked up
PHASE OV1 OP A Phase A of overvoltage 1 has operated
PHASE OV1 OP B Phase B of overvoltage 1 has operated
PHASE OV1 OP C Phase C of overvoltage 1 has operated
PHASE OV1 DPO A Phase A of overvoltage 1 has dropped out
PHASE OV1 DPO B Phase B of overvoltage 1 has dropped out
PHASE OV1 DPO C Phase C of overvoltage 1 has dropped out
ELEMENT PHASE SELECT AG Phase A to ground fault is detected.
Phase select PHASE SELECT BG Phase B to ground fault is detected.
PHASE SELECT CG Phase C to ground fault is detected.
PHASE SELECT SLG Single line to ground fault is detected.
PHASE SELECT AB Phase A to B fault is detected.
PHASE SELECT BC Phase B to C fault is detected.
PHASE SELECT CA Phase C to A fault is detected.
PHASE SELECT ABG Phase A to B to ground fault is detected.
PHASE SELECT BCG Phase B to C to ground fault is detected.
PHASE SELECT CAG Phase C to A to ground fault is detected.
PHASE SELECT 3P Three-phase symmetrical fault is detected.
PHASE SELECT MULTI-P Multi-phase fault is detected
PHASE SELECT VOID Fault type cannot be detected
ELEMENT: PHASE TOC1 PKP At least one phase of phase time overcurrent 1 has picked up
Phase time PHASE TOC1 OP At least one phase of phase time overcurrent 1 has operated
overcurrent PHASE TOC1 DPO All phases of phase time overcurrent 1 have dropped out
PHASE TOC1 PKP A Phase A of phase time overcurrent 1 has picked up
PHASE TOC1 PKP B Phase B of phase time overcurrent 1 has picked up
5 PHASE TOC1 PKP C
PHASE TOC1 OP A
PHASE TOC1 OP B
Phase C of phase time overcurrent 1 has picked up
Phase A of phase time overcurrent 1 has operated
Phase B of phase time overcurrent 1 has operated
PHASE TOC1 OP C Phase C of phase time overcurrent 1 has operated
PHASE TOC1 DPO A Phase A of phase time overcurrent 1 has dropped out
PHASE TOC1 DPO B Phase B of phase time overcurrent 1 has dropped out
PHASE TOC1 DPO C Phase C of phase time overcurrent 1 has dropped out
PHASE TOC2 to TOC6 Same set of operands as shown for PHASE TOC1
ELEMENT: PHASE UV1 PKP At least one phase of phase undervoltage 1 has picked up
Phase undervoltage PHASE UV1 OP At least one phase of phase undervoltage 1 has operated
PHASE UV1 DPO All phases of phase undervoltage 1 have dropped out
PHASE UV1 PKP A Phase A of phase undervoltage 1 has picked up
PHASE UV1 PKP B Phase B of phase undervoltage 1 has picked up
PHASE UV1 PKP C Phase C of phase undervoltage 1 has picked up
PHASE UV1 OP A Phase A of phase undervoltage 1 has operated
PHASE UV1 OP B Phase B of phase undervoltage 1 has operated
PHASE UV1 OP C Phase C of phase undervoltage 1 has operated
PHASE UV1 DPO A Phase A of phase undervoltage 1 has dropped out
PHASE UV1 DPO B Phase B of phase undervoltage 1 has dropped out
PHASE UV1 DPO C Phase C of phase undervoltage 1 has dropped out
PHASE UV2 Same set of operands as shown for PHASE UV1
ELEMENT: PMU Agg 1 SvEng On SvEng data item in associated control block is on
Synchrophasor PMU 1 CURR TRIGGER Overcurrent trigger of phasor measurement unit 1 has operated
phasor PMU 1 FREQ TRIGGER Abnormal frequency trigger of phasor measurement unit 1 has operated
measurement unit PMU 1 POWER TRIGGER Overpower trigger of phasor measurement unit 1 has operated
(PMU) PMU 1 ROCOF TRIGGER Rate of change of frequency trigger of phasor measurement unit 1 has
operated
PMU 1 VOLT TRIGGER Abnormal voltage trigger of phasor measurement unit 1 has operated
PMU 1 TRIGGERED Phasor measurement unit 1 triggered; no events or targets are generated by
this operand
ELEMENT: PMU ONE-SHOT EXPIRED Indicates the one-shot operation has been executed, and the present time is
Synchrophasor one- at least 30 seconds past the scheduled one-shot time
shot PMU ONE-SHOT OP Indicates the one-shot operation and remains asserted for 30 seconds
afterwards
PMU ONE-SHOT PENDING Indicates the one-shot operation is pending; that is, the present time is before
the scheduled one-shot time


ELEMENT: POTT OP Permissive over-reaching transfer trip has operated
POTT POTT TX1 Permissive over-reaching transfer trip asserts transmit bit number 1
(Permissive POTT TX2 Permissive over-reaching transfer trip asserts transmit bit number 2
overreach transfer POTT TX3 Permissive over-reaching transfer trip asserts transmit bit number 3
trip) POTT TX4 Permissive over-reaching transfer trip asserts transmit bit number 4
POTT TRIP A Permissive over-reaching transfer trip has operated to trip phase A
POTT TRIP B Permissive over-reaching transfer trip has operated to trip phase B
POTT TRIP C Permissive over-reaching transfer trip has operated to trip phase C
POTT TRIP 3P Permissive over-reaching transfer trip has operated to trip all three phases
ELEMENT: POTT1 OP Permissive over-reaching transfer trip ground has operated
POTT1 POTT1 TX1 Permissive over-reaching transfer trip ground asserts transmit bit number 1
(Permissive POTT1 TX2 Permissive over-reaching transfer trip ground asserts transmit bit number 2
overreach transfer POTT1 TX3 Permissive over-reaching transfer trip ground asserts transmit bit number 3
trip ground) POTT1 TX4 Permissive over-reaching transfer trip ground asserts transmit bit number 4
POTT1 TRIP A Permissive over-reaching transfer trip ground has operated to trip phase A
POTT1 TRIP B Permissive over-reaching transfer trip ground has operated to trip phase B
POTT1 TRIP C Permissive over-reaching transfer trip ground has operated to trip phase C
POTT1 TRIP 3P Permissive over-reaching transfer trip ground has operated to trip all three
phases
ELEMENT: POWER SWING OUTER Positive-sequence impedance in outer characteristic
Power swing detect POWER SWING MIDDLE Positive-sequence impedance in middle characteristic
POWER SWING INNER Positive-sequence impedance in inner characteristic
POWER SWING BLOCK Power swing blocking element operated
POWER SWING TMR1 PKP Power swing timer 1 picked up
POWER SWING TRIP Out-of-step tripping operated
POWER SWING 50DD The power swing element detected a disturbance other than power swing
POWER SWING INCOMING An unstable power swing has been detected (incoming locus)
POWER SWING OUTGOING
POWER SWING UN/BLOCK
An unstable power swing has been detected (outgoing locus)
Asserted when power swing is detected and de-asserted when a fault during 5
power swing occurs
ELEMENT: PUTT OP Permissive under-reaching transfer trip has operated
PUTT PUTT TX1 Permissive under-reaching transfer trip asserts transmit bit number 1
(Permissive PUTT TX2 Permissive under-reaching transfer trip asserts transmit bit number 2
underreach transfer PUTT TX3 Permissive under-reaching transfer trip asserts transmit bit number 3
trip) PUTT TX4 Permissive under-reaching transfer trip asserts transmit bit number 4
PUTT TRIP A Permissive under-reaching transfer trip has operated to trip phase A
PUTT TRIP B Permissive under-reaching transfer trip has operated to trip phase B
PUTT TRIP C Permissive under-reaching transfer trip has operated to trip phase C
PUTT TRIP 3P Permissive under-reaching transfer trip has operated to trip all three phases
ELEMENT: SELECTOR 1 POS Y Selector switch 1 is in Position Y (mutually exclusive operands)
Selector switch SELECTOR 1 BIT 0 First bit of the 3-bit word encoding position of selector 1
SELECTOR 1 BIT 1 Second bit of the 3-bit word encoding position of selector 1
SELECTOR 1 BIT 2 Third bit of the 3-bit word encoding position of selector 1
SELECTOR 1 STP ALARM Position of selector 1 has been pre-selected with the stepping up control
input but not acknowledged
SELECTOR 1 BIT ALARM Position of selector 1 has been pre-selected with the 3-bit control input but
not acknowledged
SELECTOR 1 ALARM Position of selector 1 has been pre-selected but not acknowledged
SELECTOR 1 PWR ALARM Position of selector switch 1 is undetermined or restored from memory when
the relay powers up and synchronizes to the three-bit input
SELECTOR 2 Same set of operands as shown above for SELECTOR 1
ELEMENT: SETTING GROUP ACT 1 Setting group 1 is active
Setting group SETTING GROUP ACT 2 Setting group 2 is active
SETTING GROUP ACT 3 Setting group 3 is active


ELEMENT: SH STAT GND STG1 PKP Stage 1 of the sub-harmonic stator ground protection has picked up
Sub-harmonic stator SH STAT GND STG1 DPO Stage 1 of the sub-harmonic stator ground protection has dropped out
ground fault detector SH STAT GND STG1 OP Stage 1 of the sub-harmonic stator ground protection has operated
SH STAT GND STG2 PKP Stage 2 of the sub-harmonic stator ground protection has picked up
SH STAT GND STG2 DPO Stage 2 of the sub-harmonic stator ground protection has dropped out
SH STAT GND STG2 OP Stage 2 of the sub-harmonic stator ground protection has operated
SH STAT GND OC PKP Ground over current element of the sub-harmonic stator ground protection
has picked up
SH STAT GND OC DPO Ground over current element of the sub-harmonic stator ground protection
has dropped out
SH STAT GND OC OP Ground over current element of the sub-harmonic stator ground protection
has operated
SH STAT GND TRB PKP Sub-harmonic stator ground module trouble has picked up
SH STAT GND TRB DPO Sub-harmonic stator ground module trouble has dropped out
SH STAT GND TRB OP Sub-harmonic stator ground module trouble has operated
ELEMENT: SRC1 50DD OP Source 1 disturbance detector has operated
Disturbance SRC2 50DD OP Source 2 disturbance detector has operated
detector SRC3 50DD OP Source 3 disturbance detector has operated
SRC4 50DD OP Source 4 disturbance detector has operated
ELEMENT: SRC1 VT FF OP Source 1 VT fuse failure detector has operated

VTFF (Voltage SRC1 VT FF DPO Source 1 VT fuse failure detector has dropped out
transformer fuse SRC1 VT FF VOL LOSS Source 1 has lost voltage signals (V2 below 10% and V1 below 5%
failure) of nominal)
SRC1 VT NEU WIRE OPEN Source 1 VT neutral wire open detected.When the VT is connected in Delta,
this function should not be enabled because there is no neutral wire for Delta
connected VT.
SRC2 VT FF to Same set of operands as shown for SRC1 VT FF
SRC4 VT FF
5 ELEMENT:
Disconnect switch
SWITCH 1 OFF CMD
SWITCH 1 ON CMD
Disconnect switch 1 open command initiated
Disconnect switch 1 close command initiated
SWITCH 1 CLOSED Disconnect switch 1 is closed
SWITCH 1 OPEN Disconnect switch 1 is open
SWITCH 1 DISCREP Disconnect switch 1 has discrepancy
SWITCH 1 TROUBLE Disconnect switch 1 trouble alarm
SWITCH 1 A CLSD Disconnect switch 1 phase A is closed
SWITCH 1 A OPEN Disconnect switch 1 phase A is open
SWITCH 1 A BAD ST Disconnect switch 1 phase A bad status is detected (discrepancy between
SWITCH 1 A INTERM Disconnect switch 1 phase A intermediate status is detected (transition from
one position to another)
SWITCH 1 B CLSD Disconnect switch 1 phase B is closed
SWITCH 1 B OPEN Disconnect switch 1 phase B is open
SWITCH 1 B BAD ST Disconnect switch 1 phase B bad status is detected (discrepancy between
SWITCH 1 B INTERM Disconnect switch 1 phase B intermediate status is detected (transition from
SWITCH 1 C CLSD Disconnect switch 1 phase C is closed
SWITCH 1 C OPEN Disconnect switch 1 phase C is open
SWITCH 1 C BAD ST Disconnect switch 1 phase C bad status is detected (discrepancy between
SWITCH 1 C INTERM Disconnect switch 1 phase C intermediate status is detected (transition from
SWITCH 1 BAD STATUS Disconnect switch 1 bad status is detected on any pole
SWITCH 2... Same set of operands as shown for SWITCH 1
ELEMENT: SYNC 1 DEAD S OP Synchrocheck 1 dead source has operated
Synchrocheck SYNC 1 DEAD S DPO Synchrocheck 1 dead source has dropped out
SYNC 1 SYNC OP Synchrocheck 1 in synchronization has operated
SYNC 1 SYNC DPO Synchrocheck 1 in synchronization has dropped out
SYNC 1 CLS OP Synchrocheck 1 close has operated
SYNC 1 CLS DPO Synchrocheck 1 close has dropped out
SYNC 1 V1 ABOVE MIN Synchrocheck 1 V1 is above the minimum live voltage
SYNC 1 V1 BELOW MAX Synchrocheck 1 V1 is below the maximum dead voltage
SYNC 1 V2 ABOVE MIN Synchrocheck 1 V2 is above the minimum live voltage
SYNC 1 V2 BELOW MAX Synchrocheck 1 V2 is below the maximum dead voltage
SYNC 2 Same set of operands as shown for SYNC 1


ELEMENT: TELEPRO CH1 FAIL Channel 1 failed
Teleprotection TELEPRO CH2 FAIL Channel 2 failed
channel tests TELEPRO CH1 ID FAIL The ID check for a peer relay on channel 1 has failed
TELEPRO CH2 ID FAIL The ID check for a peer relay on channel 2 has failed
TELEPRO CH1 CRC FAIL CRC detected packet corruption on channel 1
TELEPRO CH2 CRC FAIL CRC detected packet corruption on channel 2
TELEPRO CH1 PKT LOST CRC detected lost packet on channel 1
TELEPRO CH2 PKT LOST CRC detected lost packet on channel 2
ELEMENT: TELEPRO INPUT 1-1 On Flag is set, Logic =1
Teleprotection  
inputs/outputs TELEPRO INPUT 1-16 On Flag is set, Logic =1
TELEPRO INPUT 2-1 On Flag is set, Logic =1
 
TELEPRO INPUT 2-16 On Flag is set, Logic =1
ELEMENT: THERMAL PROT 1 PKP Thermal overload protection 1 picked up
Thermal overload THERMAL PROT 1 OP Thermal overload protection 1 operated
protection
ELEMENT TRIP 3-POLE Trip all three breaker poles
Trip output TRIP 1-POLE A single-pole trip-and-reclose operation is initiated
TRIP PHASE A Trip breaker pole A, initiate phase A breaker fail and reclose
TRIP PHASE B Trip breaker pole B, initiate phase B breaker fail and reclose
TRIP PHASE C Trip breaker pole C, initiate phase C breaker fail and reclose
TRIP AR INIT 3-POLE Initiate a three-pole reclose
TRIP FORCE 3-POLE Three-pole trip must be initiated
TRIP OUTPUT OP Any trip is initiated by the trip output
TRIP Z2PH TMR INIT Phase distance zone 2 timer is initiated by the trip output
TRIP Z2GR TMR INIT Ground distance zone 2 timer is initiated by the trip output
ELEMENT TRIP BUS 1 PKP Asserted when the trip bus 1 element picks up.
Trip bus TRIP BUS 1 OP Asserted when the trip bus 1 element operates.
TRIP BUS 2... Same set of operands as shown for TRIP BUS 1 5
ELEMENT: UNDERFREQ 1 PKP Underfrequency 1 has picked up
Underfrequency UNDERFREQ 1 OP Underfrequency 1 has operated
UNDERFREQ 1 DPO Underfrequency 1 has dropped out
UNDERFREQ 2 to 6 Same set of operands as shown for UNDERFREQ 1 above
ELEMENT: WATTMETRIC 1 PKP Wattmetric directional element 1 has picked up
Wattmetric zero- WATTMETRIC 1 OP Wattmetric directional element 1 has operated
sequence
directional WATTMETRIC 2... Same set of operands as per WATTMETRIC 1 above
FIXED OPERANDS Off Logic = 0. Does nothing and may be used as a delimiter in an equation list;
used as ‘Disable’ by other features.
On Logic = 1. Can be used as a test setting.
INPUTS/OUTPUTS: Cont Ip 1 On (will not appear unless ordered)
Contact inputs Cont Ip 2 On (will not appear unless ordered)
 
Cont Ip 1 Off (will not appear unless ordered)
Cont Ip 2 Off (will not appear unless ordered)
 
INPUTS/OUTPUTS: Cont Op 1 IOn (will not appear unless ordered)
Contact outputs, Cont Op 2 IOn (will not appear unless ordered)
current  
(from detector on
form-A output only)
INPUTS/OUTPUTS: Cont Op 1 VOn (will not appear unless ordered)
Contact outputs, Cont Op 2 VOn (will not appear unless ordered)
voltage  
(from detector on
form-A output only) Cont Op 1 VOff (will not appear unless ordered)
Cont Op 2 VOff (will not appear unless ordered)
 
INPUTS/OUTPUTS DIRECT INPUT 1 On Flag is set, logic=1
Direct inputs  
DIRECT INPUT 32 On Flag is set, logic=1


INPUTS/OUTPUTS: RemDPS Ip 1 BAD Asserted while the remote double-point status input is in the bad state.
Remote double- RemDPS Ip 1 INTERM Asserted while the remote double-point status input is in the intermediate
point status inputs state.
RemDPS Ip 1 OFF Asserted while the remote double-point status input is off.
RemDPS Ip 1 ON Asserted while the remote double-point status input is on.
REMDPS Ip 2... Same set of operands as per REMDPS 1 above
INPUTS/OUTPUTS: REMOTE INPUT 1 On Flag is set, logic=1
Remote inputs REMOTE INPUT 2 On Flag is set, logic=1
REMOTE INPUT 2 On Flag is set, logic=1
 
REMOTE INPUT 32 On Flag is set, logic=1
INPUTS/OUTPUTS: Virt Ip 1 On Flag is set, logic=1

Virtual inputs Virt Ip 2 On Flag is set, logic=1
Virt Ip 3 On Flag is set, logic=1
 
Virt Ip 64 On Flag is set, logic=1
INPUTS/OUTPUTS: Virt Op 1 On Flag is set, logic=1
Virtual outputs Virt Op 2 On Flag is set, logic=1
Virt Op 3 On Flag is set, logic=1
 
Virt Op 96 On Flag is set, logic=1
LED INDICATORS: LED IN SERVICE Asserted when the front panel IN SERVICE LED is on.
Fixed front panel LED TROUBLE Asserted when the front panel TROUBLE LED is on.
LEDs LED TEST MODE Asserted when the front panel TEST MODE LED is on.
LED TRIP Asserted when the front panel TRIP LED is on.
LED ALARM Asserted when the front panel ALARM LED is on.
LED PICKUP Asserted when the front panel PICKUP LED is on.
5 LED VOLTAGE
LED CURRENT
LED FREQUENCY
Asserted when the front panel VOLTAGE LED is on.
Asserted when the front panel CURRENT LED is on.
Asserted when the front panel FREQUENCY LED is on.
LED OTHER Asserted when the front panel OTHER LED is on.
LED PHASE A Asserted when the front panel PHASE A LED is on.
LED PHASE B Asserted when the front panel PHASE B LED is on.
LED PHASE C Asserted when the front panel PHASE C LED is on.
LED NEUTRAL/GROUND Asserted when the front panel NEUTRAL/GROUND LED is on.
LED INDICATORS: LED TEST IN PROGRESS An LED test has been initiated and has not finished.
LED test
LED INDICATORS: LED USER 1 Asserted when user-programmable LED 1 is on.
User-programmable
LEDs LED USER 2 to 48 The operand above is available for user-programmable LEDs 2 through 48.
PASSWORD ACCESS LOC SETG OFF Asserted when local setting access is disabled.
SECURITY ACCESS LOC SETG ON Asserted when local setting access is enabled.
ACCESS LOC CMND OFF Asserted when local command access is disabled.
ACCESS LOC CMND ON Asserted when local command access is enabled.
ACCESS REM SETG OFF Asserted when remote setting access is disabled.
ACCESS REM SETG ON Asserted when remote setting access is enabled.
ACCESS REM CMND OFF Asserted when remote command access is disabled.
ACCESS REM CMND ON Asserted when remote command access is enabled.
UNAUTHORIZED ACCESS Asserted when a password entry fails while accessing a password protected
level of the D60.
REMOTE DEVICES REMOTE DEVICE 1 On Flag is set, logic=1
REMOTE DEVICE 2 On Flag is set, logic=1
 
REMOTE DEVICE 1 Off Flag is set, logic=1

 
RESETTING RESET OP Reset command is operated (set by all three operands below).
RESET OP (COMMS) Communications source of the reset command.
RESET OP (OPERAND) Operand (assigned in the INPUTS/OUTPUTS  RESETTING menu) source
of the reset command.
RESET OP (PUSHBUTTON) Reset key (pushbutton) source of the reset command.


SELF- ANY MAJOR ERROR Any of the major self-test errors generated (major error)
DIAGNOSTICS ANY MINOR ERROR Any of the minor self-test errors generated (minor error)
(See Relay Self- ANY SELF-TESTS Any self-test errors generated (generic, any error)
tests descriptions in BATTERY FAIL The battery is not functioning. Return power supply module to manufacturer.
Chapter 7: CLOCK UNSYNCHRONIZED Relay is not synchronized to the international time standard
Commands and DIRECT DEVICE OFF A direct device is configured but not connected
Targets) DIRECT RING BREAK The Direct I/O settings is for a connection that is not in a ring
EQUIPMENT MISMATCH The configuration of modules does not match the stored order code
FLEXLOGIC ERR TOKEN A FlexLogic equation is incorrect
LATCHING OUT ERROR A difference is detected between the desired and actual latch contact state
MAINTENANCE ALERT A subset of the minor self-test errors generated, see Chapter 7
FIRST ETHERNET FAIL Link failure detected. See description in Chapter 7: Commands and targets.
PROCESS BUS FAILURE See description in Chapter 7: Commands and targets
PTP FAILURE "Bad PTP Signal" self-test as described in Chapter 7
REMOTE DEVICE OFF One or more GOOSE devices are not responding
RRTD COMM FAIL See description in Chapter 7: Commands and targets
SECOND ETHERNET FAIL See description in Chapter 7: Commands and targets
THIRD ETHERNET FAIL See description in Chapter 7: Commands and targets
SNTP FAILURE SNTP server is not responding
SYSTEM EXCEPTION See description in Chapter 7: Commands and targets
TEMP MONITOR Monitors ambient temperature and maximum operating temperature
UNIT NOT PROGRAMMED The product setup>installation>relay settings setting is not programmed
TEMPERATURE TEMP MONITOR Asserted while the ambient temperature is greater than the maximum
MONITOR operating temperature (80°C)
USER- PUSHBUTTON 1 ON Pushbutton number 1 is in the “On” position
PROGRAMMABLE PUSHBUTTON 1 OFF Pushbutton number 1 is in the “Off” position
PUSHBUTTONS ANY PB ON Any of twelve pushbuttons is in the “On” position
PUSHBUTTON 2 to 12 Same set of operands as PUSHBUTTON 1
Some operands can be re-named by the user. These are the names of the breakers in the breaker control feature, the ID
(identification) of contact inputs, the ID of virtual inputs, and the ID of virtual outputs. If the user changes the default name
5
or ID of any of these operands, the assigned name will appear in the relay list of operands. The default names are shown in
the FlexLogic operands table above.
The characteristics of the logic gates are tabulated below, and the operators available in FlexLogic are listed in the Flex-
Logic operators table.
Table 5–16: FLEXLOGIC GATE CHARACTERISTICS

GATES NUMBER OF INPUTS OUTPUT IS ‘1’ (= ON) IF...
NOT 1 input is ‘0’
OR 2 to 16 any input is ‘1’
AND 2 to 16 all inputs are ‘1’
NOR 2 to 16 all inputs are ‘0’
NAND 2 to 16 any input is ‘0’
XOR 2 only one input is ‘1’

Table 5–17: FLEXLOGIC OPERATORS

TYPE SYNTAX DESCRIPTION NOTES
Editor INSERT Insert a parameter in an equation list.
DELETE Delete a parameter from an equation list.
End END The first END encountered signifies the last entry in
the list of processed FlexLogic parameters.
One-shot POSITIVE ONE SHOT One shot that responds to a positive going edge. A ‘one shot’ refers to a single input gate
that generates a pulse in response to an
NEGATIVE ONE One shot that responds to a negative going edge. edge on the input. The output from a ‘one
SHOT shot’ is True (positive) for only one pass
DUAL ONE SHOT One shot that responds to both the positive and through the FlexLogic equation. There is a
negative going edges. maximum of 64 ‘one shots’.
Logic NOT Logical NOT Operates on the previous parameter.
gate
OR(2) 2 input OR gate Operates on the 2 previous parameters.
  
OR(16) 16 input OR gate Operates on the 16 previous parameters.
AND(2) 2 input AND gate Operates on the 2 previous parameters.
  
AND(16) 16 input AND gate Operates on the 16 previous parameters.
NOR(2) 2 input NOR gate Operates on the 2 previous parameters.
  
NOR(16) 16 input NOR gate Operates on the 16 previous parameters.
NAND(2) 2 input NAND gate Operates on the 2 previous parameters.
  
NAND(16) 16 input NAND gate Operates on the 16 previous parameters.
XOR(2) 2 input Exclusive OR gate Operates on the 2 previous parameters.
5 LATCH (S,R) Latch (set, reset): reset-dominant The parameter preceding LATCH(S,R) is
the reset input. The parameter preceding
the reset input is the set input.
Timer TIMER 1 Timer set with FlexLogic timer 1 settings. The timer is started by the preceding
  parameter. The output of the timer is
TIMER 32 Timer set with FlexLogic timer 32 settings. TIMER #.
Assign = Virt Op 1 Assigns previous FlexLogic operand to virtual The virtual output is set by the preceding
virtual  output 1. parameter
output = Virt Op 96 
Assigns previous FlexLogic operand to virtual
output 96.
5.5.2 FLEXLOGIC RULES
When forming a FlexLogic equation, the sequence in the linear array of parameters must follow these general rules:
1. Operands must precede the operator which uses the operands as inputs.
2. Operators have only one output. The output of an operator must be used to create a virtual output if it is to be used as
an input to two or more operators.
3. Assigning the output of an operator to a virtual output terminates the equation.
4. A timer operator (for example, "TIMER 1") or virtual output assignment (for example, " = Virt Op 1") may only be used
once. If this rule is broken, a syntax error will be declared.
5.5.3 FLEXLOGIC EVALUATION
Each equation is evaluated in the order in which the parameters have been entered.
FlexLogic provides latches which by definition have a memory action, remaining in the set state after the set input
has been asserted. However, they are volatile; that is, they reset on the re-application of control power.
NOTE
When making changes to settings, all FlexLogic equations are re-compiled whenever any new setting value is
entered, so all latches are automatically reset. If it is necessary to re-initialize FlexLogic during testing, for example,
it is suggested to power the unit down and then back up.

5.5.4 FLEXLOGIC EXAMPLE
This section provides an example of implementing logic for a typical application. The sequence of the steps is quite impor-
tant as it should minimize the work necessary to develop the relay settings. Note that the example presented in the figure
below is intended to demonstrate the procedure, not to solve a specific application situation.
In the example below, it is assumed that logic has already been programmed to produce virtual outputs 1 and 2, and is only
a part of the full set of equations used. When using FlexLogic, it is important to make a note of each virtual output used – a
virtual output designation (1 to 96) can only be properly assigned once.
VIRTUAL OUTPUT 1
State=ON
VIRTUAL OUTPUT 2
Set
State=ON
LATCH
VIRTUAL INPUT 1 OR #1 Reset
State=ON Timer 2
XOR Time Delay Operate Output
DIGITAL ELEMENT 1 OR #2
on Dropout Relay H1
State=Pickup
(200 ms)
DIGITAL ELEMENT 2 Timer 1

State=Operated Time Delay
AND
on Pickup
(800 ms)
CONTACT INPUT H1c 827025A2.vsd
State=Closed
Figure 5–54: EXAMPLE LOGIC SCHEME

1. Inspect the example logic diagram to determine if the required logic can be implemented with the FlexLogic operators.
If this is not possible, the logic must be altered until this condition is satisfied. Once this is done, count the inputs to
5
each gate to verify that the number of inputs does not exceed the FlexLogic limits, which is unlikely but possible. If the
number of inputs is too high, subdivide the inputs into multiple gates to produce an equivalent. For example, if 25
inputs to an AND gate are required, connect Inputs 1 through 16 to AND(16), 17 through 25 to AND(9), and the outputs
from these two gates to AND(2).
Inspect each operator between the initial operands and final virtual outputs to determine if the output from the operator
is used as an input to more than one following operator. If so, the operator output must be assigned as a virtual output.
For the example shown above, the output of the AND gate is used as an input to both OR#1 and Timer 1, and must
therefore be made a virtual output and assigned the next available number (i.e. Virtual Output 3). The final output must
also be assigned to a virtual output as virtual output 4, which will be programmed in the contact output section to oper-
ate relay H1 (that is, contact output H1).
Therefore, the required logic can be implemented with two FlexLogic equations with outputs of virtual output 3 and vir-
tual output 4 as shown below.
VIRTUAL OUTPUT 1
State=ON
VIRTUAL OUTPUT 2
Set
State=ON
LATCH
State=ON Timer 2
XOR Time Delay
DIGITAL ELEMENT 1 OR #2 VIRTUAL OUTPUT 4
on Dropout
State=Pickup (200 ms)
DIGITAL ELEMENT 2 Timer 1

State=Operated Time Delay
AND
on Pickup
(800 ms)
CONTACT INPUT H1c
State=Closed VIRTUAL OUTPUT 3
827026A2.VSD
Figure 5–55: LOGIC EXAMPLE WITH VIRTUAL OUTPUTS

2. Prepare a logic diagram for the equation to produce virtual output 3, as this output will be used as an operand in the
virtual output 4 equation (create the equation for every output that will be used as an operand first, so that when these
operands are required they will already have been evaluated and assigned to a specific virtual output). The logic for
virtual output 3 is shown below with the final output assigned.
DIGITAL ELEMENT 2
State=Operated
AND(2) VIRTUAL OUTPUT 3
CONTACT INPUT H1c

State=Closed
827027A2.VSD
Figure 5–56: LOGIC FOR VIRTUAL OUTPUT 3

3. Prepare a logic diagram for virtual output 4, replacing the logic ahead of virtual output 3 with a symbol identified as vir-
tual output 3, as shown below.
VIRTUAL OUTPUT 1
State=ON
VIRTUAL OUTPUT 2
Set
State=ON
LATCH
State=ON Timer 2
XOR Time Delay VIRTUAL
DIGITAL ELEMENT 1 OR #2
on Dropout OUTPUT 4
State=Pickup
(200 ms)
Timer 1
5 VIRTUAL OUTPUT 3
State=ON
Time Delay
on Pickup
(800 ms)
CONTACT INPUT H1c
State=Closed 827028A2.VSD
Figure 5–57: LOGIC FOR VIRTUAL OUTPUT 4

4. Program the FlexLogic equation for virtual output 3 by translating the logic into available FlexLogic parameters. The
equation is formed one parameter at a time until the required logic is complete. It is generally easier to start at the out-
put end of the equation and work back towards the input, as shown in the following steps. It is also recommended to list
operator inputs from bottom to top. For demonstration, the final output will be arbitrarily identified as parameter 99, and
each preceding parameter decremented by one in turn. Until accustomed to using FlexLogic, it is suggested that a
worksheet with a series of cells marked with the arbitrary parameter numbers be prepared, as shown below.
01
02
03
04
05
.....
97
98
99
827029A1.VSD
Figure 5–58: FLEXLOGIC WORKSHEET

5. Following the procedure outlined, start with parameter 99, as follows:
99: The final output of the equation is virtual output 3, which is created by the operator "= Virt Op n". This parameter is
therefore "= Virt Op 3."

98: The gate preceding the output is an AND, which in this case requires two inputs. The operator for this gate is a 2-
input AND so the parameter is “AND(2)”. Note that FlexLogic rules require that the number of inputs to most types
of operators must be specified to identify the operands for the gate. As the 2-input AND will operate on the two
operands preceding it, these inputs must be specified, starting with the lower.
97: This lower input to the AND gate must be passed through an inverter (the NOT operator) so the next parameter is
“NOT”. The NOT operator acts upon the operand immediately preceding it, so specify the inverter input next.
96: The input to the NOT gate is to be contact input H1c. The ON state of a contact input can be programmed to be
set when the contact is either open or closed. Assume for this example the state is to be ON for a closed contact.
The operand is therefore “Cont Ip H1c On”.
95: The last step in the procedure is to specify the upper input to the AND gate, the operated state of digital element 2.
This operand is "DIG ELEM 2 OP".
Writing the parameters in numerical order can now form the equation for virtual output 3:
[95] DIG ELEM 2 OP
[96] Cont Ip H1c On
[97] NOT
[98] AND(2)
[99] = Virt Op 3
It is now possible to check that this selection of parameters will produce the required logic by converting the set of parame-
ters into a logic diagram. The result of this process is shown below, which is compared to the logic for virtual output 3 dia-
gram as a check.
FLEXLOGIC ENTRY n:
95 DIG ELEM 2 OP VIRTUAL
AND
FLEXLOGIC ENTRY n: OUTPUT 3
96 Cont Ip H1c On
FLEXLOGIC ENTRY n:
5
97 NOT
FLEXLOGIC ENTRY n:
98 AND (2)
FLEXLOGIC ENTRY n:
99 =Virt Op 3
827030A2.VSD
Figure 5–59: FLEXLOGIC EQUATION FOR VIRTUAL OUTPUT 3

6. Repeating the process described for virtual output 3, select the FlexLogic parameters for Virtual Output 4.
99: The final output of the equation is virtual output 4 which is parameter “= Virt Op 4".
98: The operator preceding the output is timer 2, which is operand “TIMER 2". Note that the settings required for the
timer are established in the timer programming section.
97: The operator preceding timer 2 is OR #2, a 3-input OR, which is parameter “OR(3)”.
96: The lowest input to OR #2 is operand “Cont Ip H1c On”.
95: The center input to OR #2 is operand “TIMER 1".
94: The input to timer 1 is operand “Virt Op 3 On".
93: The upper input to OR #2 is operand “LATCH (S,R)”.
92: There are two inputs to a latch, and the input immediately preceding the latch reset is OR #1, a 4-input OR, which
is parameter “OR(4)”.
91: The lowest input to OR #1 is operand “Virt Op 3 On".
90: The input just above the lowest input to OR #1 is operand “XOR(2)”.
89: The lower input to the XOR is operand “DIG ELEM 1 PKP”.
88: The upper input to the XOR is operand “Virt Ip 1 On".
87: The input just below the upper input to OR #1 is operand “Virt Op 2 On".
86: The upper input to OR #1 is operand “Virt Op 1 On".
85: The last parameter is used to set the latch, and is operand “Virt Op 4 On".

The equation for virtual output 4 is:

[85] Virt Op 4 On
[86] Virt Op 1 On
[87] Virt Op 2 On
[88] Virt Ip 1 On
[89] DIG ELEM 1 PKP
[90] XOR(2)
[91] Virt Op 3 On
[92] OR(4)
[93] LATCH (S,R)
[94] Virt Op 3 On
[95] TIMER 1
[96] Cont Ip H1c On
[97] OR(3)
[98] TIMER 2
[99] = Virt Op 4
It is now possible to check that the selection of parameters will produce the required logic by converting the set of parame-
ters into a logic diagram. The result of this process is shown below, which is compared to the logic for virtual output 4 dia-
gram as a check.
FLEXLOGIC ENTRY n:
85 Virt Op 4 On
FLEXLOGIC ENTRY n:
86 Virt Op 1 On
FLEXLOGIC ENTRY n:
5 87
88
Virt Op 2 On
FLEXLOGIC ENTRY n:
Set
LATCH
Virt Ip 1 On
XOR OR Reset
FLEXLOGIC ENTRY n:
89 DIG ELEM 1 PKP
FLEXLOGIC ENTRY n:
90 XOR
FLEXLOGIC ENTRY n:
91 Virt Op 3 On VIRTUAL
OR T2 OUTPUT 4
FLEXLOGIC ENTRY n:
92 OR (4)
FLEXLOGIC ENTRY n:
93 LATCH (S,R)
FLEXLOGIC ENTRY n:
94 Virt Op 3 On T1
FLEXLOGIC ENTRY n:
95 TIMER 1
FLEXLOGIC ENTRY n:
96 Cont Ip H1c On
FLEXLOGIC ENTRY n:
97 OR (3)
FLEXLOGIC ENTRY n:
98 TIMER 2
FLEXLOGIC ENTRY n:
99 =Virt Op 4 827031A2.VSD
Figure 5–60: FLEXLOGIC EQUATION FOR VIRTUAL OUTPUT 4

7. Now write the complete FlexLogic expression required to implement the logic, making an effort to assemble the equa-
tion in an order where Virtual Outputs that will be used as inputs to operators are created before needed. In cases
where a lot of processing is required to perform logic, this may be difficult to achieve, but in most cases will not cause
problems as all logic is calculated at least four times per power frequency cycle. The possibility of a problem caused by
sequential processing emphasizes the necessity to test the performance of FlexLogic before it is placed in service.
In the following equation, virtual output 3 is used as an input to both latch 1 and timer 1 as arranged in the order shown
below:
DIG ELEM 2 OP
Cont Ip H1c On
NOT
AND(2)

= Virt Op 3
Virt Op 4 On
Virt Op 1 On
Virt Op 2 On
Virt Ip 1 On
DIG ELEM 1 PKP
XOR(2)
Virt Op 3 On
OR(4)
LATCH (S,R)
Virt Op 3 On
TIMER 1
Cont Ip H1c On
OR(3)
TIMER 2
= Virt Op 4
END
In the expression above, the virtual output 4 input to the four-input OR is listed before it is created. This is typical of a
form of feedback, in this case, used to create a seal-in effect with the latch, and is correct.
8. The logic should always be tested after it is loaded into the relay, in the same fashion as has been used in the past.
Testing can be simplified by placing an "END" operator within the overall set of FlexLogic equations. The equations will
then only be evaluated up to the first "END" operator.
The "On" and "Off" operands can be placed in an equation to establish a known set of conditions for test purposes, and
the "INSERT" and "DELETE" commands can be used to modify equations.
5.5.5 FLEXLOGIC EQUATION EDITOR

5
PATH: SETTINGS  FLEXLOGIC  FLEXLOGIC EQUATION EDITOR
 FLEXLOGIC FLEXLOGIC ENTRY 1: Range: FlexLogic operands

 EQUATION EDITOR END
FLEXLOGIC ENTRY 2: Range: FlexLogic operands
MESSAGE
END

FLEXLOGIC ENTRY 512: Range: FlexLogic operands

MESSAGE
END
There are 512 FlexLogic entries available, numbered from 1 to 512, with default END entry settings. If a "Disabled" Element
is selected as a FlexLogic entry, the associated state flag will never be set to ‘1’. The ‘+/–‘ key may be used when editing
FlexLogic equations from the keypad to quickly scan through the major parameter types.
5.5.6 FLEXLOGIC TIMERS
PATH: SETTINGS  FLEXLOGIC  FLEXLOGIC TIMERS  FLEXLOGIC TIMER 1(32)
 FLEXLOGIC TIMER 1 Range: millisecond, second, minute

 TIMER 1 TYPE: millisecond
TIMER 1 PICKUP Range: 0 to 60000 in steps of 1
MESSAGE
DELAY: 0
TIMER 1 DROPOUT Range: 0 to 60000 in steps of 1
MESSAGE
DELAY: 0
There are 32 identical FlexLogic timers available. These timers can be used as operators for FlexLogic equations.
• TIMER 1 TYPE: This setting is used to select the time measuring unit.
• TIMER 1 PICKUP DELAY: Sets the time delay to pickup. If a pickup delay is not required, set this function to "0".

• TIMER 1 DROPOUT DELAY: Sets the time delay to dropout. If a dropout delay is not required, set this function to "0".
5.5.7 FLEXELEMENTS
PATH: SETTING  FLEXLOGIC  FLEXELEMENTS  FLEXELEMENT 1(8)
 FLEXELEMENT 1 FLEXELEMENT 1 Range: Disabled, Enabled

FLEXELEMENT 1 NAME: Range: up to 6 alphanumeric characters
MESSAGE
FxE1
FLEXELEMENT 1 +IN: Range: Off, any analog actual value parameter
MESSAGE
Off
FLEXELEMENT 1 -IN: Range: Off, any analog actual value parameter
MESSAGE
Off
FLEXELEMENT 1 INPUT Range: Signed, Absolute
MESSAGE
MODE: Signed
FLEXELEMENT 1 COMP Range: Level, Delta
MESSAGE
MODE: Level
FLEXELEMENT 1 Range: Over, Under
MESSAGE
DIRECTION: Over
FLEXELEMENT 1 Range: –90.000 to 90.000 pu in steps of 0.001
MESSAGE
5 PICKUP: 1.000 pu
FLEXELEMENT 1 Range: 0.1 to 50.0% in steps of 0.1
MESSAGE
HYSTERESIS: 3.0%
FLEXELEMENT 1 dt Range: milliseconds, seconds, minutes
MESSAGE
UNIT: milliseconds
FLEXELEMENT 1 dt: Range: 20 to 86400 in steps of 1
MESSAGE
20
FLEXELEMENT 1 PKP Range: 0.000 to 65.535 s in steps of 0.001
MESSAGE
DELAY: 0.000 s
FLEXELEMENT 1 RST Range: 0.000 to 65.535 s in steps of 0.001
MESSAGE
DELAY: 0.000 s
FLEXELEMENT 1 BLK: Range: FlexLogic operand
MESSAGE
Off
FLEXELEMENT 1 Range: Self-reset, Latched, Disabled
MESSAGE
TARGET: Self-reset
FLEXELEMENT 1 Range: Disabled, Enabled
MESSAGE
EVENTS: Disabled
A FlexElement is a universal comparator that can be used to monitor any analog actual value calculated by the relay or a
net difference of any two analog actual values of the same type. The effective operating signal could be treated as a signed
number or its absolute value could be used as per user's choice.
The element can be programmed to respond either to a signal level or to a rate-of-change (delta) over a pre-defined period
of time. The output operand is asserted when the operating signal is higher than a threshold or lower than a threshold as
per user's choice.

SETTING
SETTINGS
FLEXELEMENT 1
FUNCTION: FLEXELEMENT 1 INPUT MODE:
Enabled = 1
FLEXELEMENT 1 COMP MODE:
FLEXELEMENT 1 DIRECTION:
SETTING
FLEXELEMENT 1 PICKUP:
FLEXELEMENT 1 BLK:
FLEXELEMENT 1 INPUT
AND HYSTERESIS:
Off = 0
FLEXELEMENT 1 dt UNIT: SETTINGS
SETTINGS FLEXELEMENT 1 PKP

FLEXELEMENT 1 dt: DELAY:
FLEXELEMENT 1 +IN: FLEXELEMENT 1 RST
RUN DELAY:
Actual Value FLEXLOGIC OPERANDS
+ tPKP
FLEXELEMENT 1 -IN: FxE 1 OP
- tRST
Actual Value FxE 1 DPO
FxE 1 PKP
ACTUAL VALUE
FlexElement 1 OpSig
842004A4.CDR
Figure 5–61: FLEXELEMENT SCHEME LOGIC

The FLEXELEMENT 1 +IN setting specifies the first (non-inverted) input to the FlexElement. Zero is assumed as the input if
this setting is set to “Off”. For proper operation of the element at least one input must be selected. Otherwise, the element
will not assert its output operands.
5
This FLEXELEMENT 1 –IN setting specifies the second (inverted) input to the FlexElement. Zero is assumed as the input if
this setting is set to “Off”. For proper operation of the element at least one input must be selected. Otherwise, the element
will not assert its output operands. This input should be used to invert the signal if needed for convenience, or to make the
element respond to a differential signal such as for a top-bottom oil temperature differential alarm. The element will not
operate if the two input signals are of different types, for example if one tries to use active power and phase angle to build
the effective operating signal.
The element responds directly to the differential signal if the FLEXELEMENT 1 INPUT MODE setting is set to “Signed”. The ele-
ment responds to the absolute value of the differential signal if this setting is set to “Absolute”. Sample applications for the
“Absolute” setting include monitoring the angular difference between two phasors with a symmetrical limit angle in both
directions; monitoring power regardless of its direction, or monitoring a trend regardless of whether the signal increases of
decreases.
The element responds directly to its operating signal – as defined by the FLEXELEMENT 1 +IN, FLEXELEMENT 1 –IN and FLEX-
ELEMENT 1 INPUT MODE settings – if the FLEXELEMENT 1 COMP MODE setting is set to “Level”. The element responds to the
rate of change of its operating signal if the FLEXELEMENT 1 COMP MODE setting is set to “Delta”. In this case the FLEXELE-
MENT 1 dt UNIT and FLEXELEMENT 1 dt settings specify how the rate of change is derived.
The FLEXELEMENT 1 DIRECTION setting enables the relay to respond to either high or low values of the operating signal. The
following figure explains the application of the FLEXELEMENT 1 DIRECTION, FLEXELEMENT 1 PICKUP and FLEXELEMENT 1 HYS-
TERESIS settings.

FLEXELEMENT 1 PKP
FLEXELEMENT
DIRECTION = Over
HYSTERESIS = % of PICKUP
FlexElement 1 OpSig
PICKUP
FLEXELEMENT 1 PKP
FLEXELEMENT
DIRECTION = Under
HYSTERESIS = % of PICKUP
FlexElement 1 OpSig
PICKUP
842705A1.CDR
Figure 5–62: FLEXELEMENT DIRECTION, PICKUP, AND HYSTERESIS

In conjunction with the FLEXELEMENT 1 INPUT MODE setting the element could be programmed to provide two extra charac-
teristics as shown in the figure below.
FLEXELEMENT 1 PKP
5 FLEXELEMENT
DIRECTION = Over;
FLEXELEMENT INPUT
MODE = Signed;
FlexElement 1 OpSig
FLEXELEMENT 1 PKP
FLEXELEMENT
DIRECTION = Over;
FLEXELEMENT INPUT
MODE = Absolute;
FlexElement 1 OpSig
FLEXELEMENT 1 PKP
FLEXELEMENT
DIRECTION = Under;
FLEXELEMENT INPUT
MODE = Signed;
FlexElement 1 OpSig
FLEXELEMENT 1 PKP
FLEXELEMENT
DIRECTION = Under;
FLEXELEMENT INPUT
MODE = Absolute;
FlexElement 1 OpSig
842706A2.CDR
Figure 5–63: FLEXELEMENT INPUT MODE SETTING

The FLEXELEMENT 1 PICKUP setting specifies the operating threshold for the effective operating signal of the element. If set
to “Over”, the element picks up when the operating signal exceeds the FLEXELEMENT 1 PICKUP value. If set to “Under”, the
element picks up when the operating signal falls below the FLEXELEMENT 1 PICKUP value.
The FLEXELEMENT 1 HYSTERESIS setting controls the element dropout. It should be noticed that both the operating signal
and the pickup threshold can be negative facilitating applications such as reverse power alarm protection. The FlexElement
can be programmed to work with all analog actual values measured by the relay. The FLEXELEMENT 1 PICKUP setting is
entered in per-unit values using the following definitions of the base units:
Table 5–18: FLEXELEMENT BASE UNITS

BREAKER ARCING AMPS BASE = 2000 kA2  cycle
(Brk X Arc Amp A, B, and C)
dcmA BASE = maximum value of the DCMA INPUT MAX setting for the two transducers configured
under the +IN and –IN inputs.
DELTA TIME BASE = 1 µs
FREQUENCY fBASE = 1 Hz
PHASE ANGLE BASE = 360 degrees (see the UR angle referencing convention)
POWER FACTOR PFBASE = 1.00
RTDs BASE = 100°C
SOURCE CURRENT IBASE = maximum nominal primary RMS value of the +IN and –IN inputs
SOURCE ENERGY EBASE = 10000 MWh or MVAh, respectively
(Positive and Negative Watthours,
Positive and Negative Varhours)
SOURCE POWER PBASE = maximum value of VBASE  IBASE for the +IN and –IN inputs
SOURCE VOLTAGE VBASE = maximum nominal primary RMS value of the +IN and –IN inputs
5
SYNCHROCHECK VBASE = maximum primary RMS value of all the sources related to the +IN and –IN inputs
(Max Delta Volts)
The FLEXELEMENT 1 HYSTERESIS setting defines the pickup–dropout relation of the element by specifying the width of the
hysteresis loop as a percentage of the pickup value as shown in the FlexElement direction, pickup, and hysteresis diagram.
The FLEXELEMENT 1 DT UNIT setting specifies the time unit for the setting FLEXELEMENT 1 dt. This setting is applicable only if
FLEXELEMENT 1 COMP MODE is set to “Delta”. The FLEXELEMENT 1 DT setting specifies duration of the time interval for the
rate of change mode of operation. This setting is applicable only if FLEXELEMENT 1 COMP MODE is set to “Delta”.
This FLEXELEMENT 1 PKP DELAY setting specifies the pickup delay of the element. The FLEXELEMENT 1 RST DELAY setting
specifies the reset delay of the element.

5.5.8 NON-VOLATILE LATCHES
PATH: SETTINGS  FLEXLOGIC  NON-VOLATILE LATCHES  LATCH 1(16)
 LATCH 1 LATCH 1 Range: Disabled, Enabled

LATCH 1 TYPE: Range: Reset Dominant, Set Dominant
MESSAGE
Reset Dominant
LATCH 1 SET: Range: FlexLogic operand
MESSAGE
Off
LATCH 1 RESET: Range: FlexLogic operand
MESSAGE
Off
LATCH 1 Range: Self-reset, Latched, Disabled
MESSAGE
TARGET: Self-reset
LATCH 1 Range: Disabled, Enabled
MESSAGE
EVENTS: Disabled
The non-volatile latches provide a permanent logical flag that is stored safely and will not reset upon reboot after the relay
is powered down. Typical applications include sustaining operator commands or permanently block relay functions, such as
Autorecloser, until a deliberate interface action resets the latch. The settings element operation is described below:
• LATCH 1 TYPE: This setting characterizes Latch 1 to be Set- or Reset-dominant.
• LATCH 1 SET: If asserted, the specified FlexLogic operands 'sets' Latch 1.
5 • LATCH 1 RESET: If asserted, the specified FlexLogic operand 'resets' Latch 1.
SETTING
SETTING
LATCH N LATCH N LATCH N LATCH N LATCH N LATCH 1 FUNCTION:
TYPE SET RESET ON OFF
LATCH 1 TYPE:
Reset ON OFF ON OFF Disabled=0
Dominant Enabled=1 RUN
OFF OFF Previous Previous
State State
ON ON OFF ON SETTING
OFF ON OFF ON LATCH 1 SET:

FLEXLOGIC OPERANDS
Set ON OFF ON OFF
Dominant Off=0 SET LATCH 1 ON
ON ON ON OFF LATCH 1 OFF
OFF OFF Previous Previous SETTING
State State
LATCH 1 SET:
OFF ON OFF ON
Off=0 RESET
842005A1.CDR
Figure 5–64: NON-VOLATILE LATCH OPERATION TABLE (N = 1 to 16) AND LOGIC

5 SETTINGS 5.6 GROUPED ELEMENTS
5.6GROUPED ELEMENTS 5.6.1 OVERVIEW
Each protection element can be assigned up to six different sets of settings according to setting group designations 1 to 6.
The performance of these elements is defined by the active setting group at a given time. Multiple setting groups allow the
user to conveniently change protection settings for different operating situations (for example, altered power system config-
uration, season of the year, etc.). The active setting group can be preset or selected via the SETTING GROUPS menu (see the
Control elements section later in this chapter). See also the Introduction to elements section at the beginning of this chap-
ter.
5.6.2 SETTING GROUP
PATH: SETTINGS  GROUPED ELEMENTS  SETTING GROUP 1(6)
 SETTING GROUP 1  LINE PICKUP

See page 5-156.
 
 DISTANCE

 POWER SWING
 DETECT
 LOAD ENCROACHMENT

 PHASE CURRENT

 NEUTRAL CURRENT 5

 WATTMETRIC
 GROUND FAULT
 GROUND CURRENT

 NEGATIVE SEQUENCE
 CURRENT
 BREAKER FAILURE

 VOLTAGE ELEMENTS

 POWER

Each of the six setting group menus is identical. Setting group 1 (the default active group) automatically becomes active if
no other group is active (see the Control elements section for additional details).

5.6 GROUPED ELEMENTS 5 SETTINGS
5.6.3 LINE PICKUP
PATH: SETTINGS  GROUPED ELEMENTS  SETTING GROUP 1(6)  LINE PICKUP
 LINE PICKUP LINE PICKUP Range: Disabled, Enabled

LINE PICKUP SIGNAL Range: SRC 1, SRC 2, SRC 3, SRC 4
MESSAGE
SOURCE: SRC 1
PHASE IOC LINE Range: 0.000 to 30.000 pu in steps of 0.001
MESSAGE
PICKUP: 1.000 pu
LINE PICKUP UV PKP: Range: 0.000 to 3.000 pu in steps of 0.001
MESSAGE
0.700 pu
LINE END OPEN PICKUP Range: 0.000 to 65.535 s in steps of 0.001
MESSAGE
DELAY: 0.150 s
LINE END OPEN RESET Range: 0.000 to 65.535 s in steps of 0.001
MESSAGE
DELAY: 0.090 s
LINE PICKUP OV PKP Range: 0.000 to 65.535 s in steps of 0.001
MESSAGE
DELAY: 0.040 s
AR CO-ORD BYPASS: Range: Disabled, Enabled
MESSAGE
Enabled
AR CO-ORD PICKUP Range: 0.000 to 65.535 s in steps of 0.001
5 MESSAGE
DELAY: 0.045 s
AR CO-ORD RESET Range: 0.000 to 65.535 s in steps of 0.001
MESSAGE
DELAY: 0.005 s
TERMINAL OPEN: Range: FlexLogic operand
MESSAGE
Off
AR ACCELERATE: Range: FlexLogic operand
MESSAGE
Off
LINE PICKUP DISTANCE Range: Disabled, Enabled
MESSAGE
TRIP: Enabled
LINE PICKUP BLOCK: Range: FlexLogic operand
MESSAGE
Off
LINE PICKUP Range: Self-reset, Latched, Disabled
MESSAGE
TARGET: Self-reset
LINE PICKUP Range: Disabled, Enabled
MESSAGE
EVENTS: Disabled
The line pickup feature uses a combination of undercurrent and undervoltage to identify a line that has been de-energized
(line end open). Alternately, the user may assign a FlexLogic operand to the TERMINAL OPEN setting that specifies the termi-
nal status. Three instantaneous overcurrent elements are used to identify a previously de-energized line that has been
closed onto a fault. Faults other than close-in faults can be identified satisfactorily with the distance elements.
Co-ordination features are included to ensure satisfactory operation when high speed automatic reclosure (AR) is
employed. The AR CO-ORD DELAY setting allows the overcurrent setting to be below the expected load current seen after
reclose. Co-ordination is achieved by all of the LINE PICKP UV elements resetting and blocking the trip path before the AR
CO-ORD DELAY times out. The AR CO-ORD BYPASS setting is normally enabled. It is disabled if high speed autoreclosure is
implemented.
The line pickup protection incorporates zone 1 extension capability. When the line is being re-energized from the local ter-
minal, pickup of an overreaching zone 2 or excessive phase current within eight power cycles after the autorecloser issues
a close command results in the LINE PICKUP RCL TRIP FlexLogic operand. For security, the overcurrent trip is supervised by

an undervoltage condition, which in turn is controlled by the VT FUSE FAIL OP operand with a 10 ms coordination timer. If a
trip from distance in not required, then it can be disabled with the LINE PICKUP DISTANCE TRIP setting. Configure the LINE
PICKUP RCL TRIP operand to perform a trip action if the intent is apply zone 1 extension.
The zone 1 extension philosophy used here normally operates from an under-reaching zone, and uses an overreaching
distance zone when reclosing the line with the other line end open. The AR ACCELERATE setting is provided to achieve
zone 1 extension functionality if external autoreclosure is employed. Another zone 1 extension approach is to permanently
apply an overreaching zone, and reduce the reach when reclosing. This philosophy can be programmed via the autore-
close scheme.
6(77,1*
7HUPLQDO2SHQ )/(;/2*,&23(5$1'
2II /,1(3,&.83893.3
$1'
6(77,1* 6(77,1*
)XQFWLRQ 2YHUYROWDJH3LFNXS'HOD\
(QDEOHG 73.3
'LVDEOHG 25
7567
$1'
6(77,1*
%ORFN
2II 6(77,1* 6(77,1*6
8QGHUYROWDJH3LFNXS /LQH(QG2SHQ3LFNXS'HOD\
)/(;/2*,&23(5$1'
581 /LQH(QG2SHQ5HVHW'HOD\
/,1(3,&.83/(23.3
6(77,1* 9$*RU9$%VHWWLQJ 73.3
/(2 OLQHHQGRSHQ
6LJQDO6RXUFH 9%*RU9%&VHWWLQJ $1' 25
7567
9$* 9$% 9&*RU9&$VHWWLQJ 6(77,1*6
9%* 9%& $1' $XWRUHFORVH&RRUGLQDWLRQ
9&* 9&$ 3LFNXS'HOD\
581
,$ ,$SX $XWRUHFORVH&RRUGLQDWLRQ
5HVHW'HOD\
,% ,%SX $1'
73.3
,& ,&SX
5
$1'
7567
$1'
PV
6(77,1* $1' 25

3KDVH,2&/LQH3LFNXS $1'
$1'
581
,$!VHWWLQJ
6(77,1* ,%!VHWWLQJ 25
$XWRUHFORVH&RRUGLQDWLRQ ,&!VHWWLQJ $1'
%\SDVV )/(;/2*,&23(5$1'6
(QDEOHG 25 /,1(3,&.8323
'LVDEOHG /,1(3,&.833.3
/,1(3,&.83'32
)/(;/2*,&23(5$1'6
$1'
*1'',67=3.3
25
3+',67=3.3
$1'
25
)/(;/2*,&23(5$1'
6(77,1* $1' /,1(3,&.835&/75,3
'LVWDQFH7ULS
7,0(5
(QDEOHG

'LVDEOHG
F\FOHV )/(;/2*,&23(5$1'6
/,1(3,&.83,$
6(77,1*
/,1(3,&.83,%
$XWRUHFORVH$FFHOHUDWH
/,1(3,&.83,&
2II
)/(;/2*,&23(5$1'6 25
$5&/26(%.5
$5&/26(%.5
'/DQG/RQO\
)/(;/2*,&23(5$1'
65&;97)86()$,/23
6RXUFHVHOHFWHGLQWKHOLQHSLFNXSHOHPHQW $.&'5
Figure 5–65: LINE PICKUP SCHEME LOGIC

5.6.4 DISTANCE
a) MAIN MENU
PATH: SETTINGS  GROUPED ELEMENTS  SETTING GROUP 1(6)  DISTANCE
 DISTANCE DISTANCE Range: SRC 1, SRC 2, SRC 3, SRC 4

 SOURCE: SRC 1
MEMORY Range: 5 to 25 cycles in steps of 1
MESSAGE
DURATION: 10 cycles
FORCE SELF-POLAR: Range: FlexLogic operand
MESSAGE
Off
FORCE MEM-POLAR: Range: FlexLogic operand
MESSAGE
Off
 PHASE DISTANCE Z1




5 MESSAGE

See page 5–159.
 GROUND DISTANCE Z1





Four common settings are available for distance protection. The DISTANCE SOURCE identifies the signal source for all dis-
tance functions. The mho distance functions use a dynamic characteristic: the positive-sequence voltage – either memo-
rized or actual – is used as a polarizing signal. The memory voltage is also used by the built-in directional supervising
functions applied for both the mho and quad characteristics.
The MEMORY DURATION setting specifies the length of time a memorized positive-sequence voltage should be used in the
distance calculations. After this interval expires, the relay checks the magnitude of the actual positive-sequence voltage. If
it is higher than 10% of the nominal, the actual voltage is used, if lower – the memory voltage continues to be used.
The memory is established when the positive-sequence voltage stays above 80% of its nominal value for five power system
cycles. For this reason it is important to ensure that the nominal secondary voltage of the VT is entered correctly under the
SETTINGS  SYSTEM SETUP  AC INPUTS  VOLTAGE BANK menu.
Set MEMORY DURATION long enough to ensure stability on close-in reverse three-phase faults. For this purpose, the maxi-
mum fault clearing time (breaker fail time) in the substation should be considered. On the other hand, the MEMORY DURA-
TION cannot be too long as the power system may experience power swing conditions rotating the voltage and current
phasors slowly while the memory voltage is static, as frozen at the beginning of the fault. Keeping the memory in effect for
too long may eventually lead to incorrect operation of the distance functions.

The distance zones can be forced to become self-polarized through the FORCE SELF-POLAR setting. Any user-selected con-
dition (FlexLogic operand) can be configured to force self-polarization. When the selected operand is asserted (logic 1), the
distance functions become self-polarized regardless of other memory voltage logic conditions. When the selected operand
is de-asserted (logic 0), the distance functions follow other conditions of the memory voltage logic as shown below.
The distance zones can be forced to become memory-polarized through the FORCE MEM-POLAR setting. Any user-selected
condition (any FlexLogic operand) can be configured to force memory polarization. When the selected operand is asserted
(logic 1), the distance functions become memory-polarized regardless of the positive-sequence voltage magnitude at this
time. When the selected operand is de-asserted (logic 0), the distance functions follow other conditions of the memory volt-
age logic.
The FORCE SELF-POLAR and FORCE MEM-POLAR settings should never be asserted simultaneously. If this happens, the logic
will give higher priority to forcing self-polarization as indicated in the logic below. This is consistent with the overall philoso-
phy of distance memory polarization.
The memory polarization cannot be applied permanently but for a limited time only; the self-polarization may be
applied permanently and therefore should take higher priority.
NOTE
SETTING
Force Memory Polarization
Update memory
Off = 0
AND RUN
SETTING
Memory duration
SETTING TIMER 0
Distance Source | V_1 | < 1.15 pu 5 cycles AND
= VA, Vrms_A | Vrms – | V | | < Vrms / 8 AND Treset
S Q
= VB, Vrms_B | Vrms – | V | | < Vrms / 8 0 AND
= VC, Vrms_C | Vrms – | V | | < Vrms / 8
Use V_1 memory
5
= V_1 | V_1 | > 0.80 pu TIMER
6 cycles OR
= IA | IA | < 0.05 pu
| IB | < 0.05 pu
AND
R Use V_1
= IB OR
0
= IC | IC | < 0.05 pu AND
Tracking Freq, *SRCx Freq | V_1 | < 0.10 pu
*SRCx is the source used in distance | fTRACK - fSRC | > 1 Hz
L90 Only
SETTING
Force Self Polarization
Off = 0 827842A9.CDR
Figure 5–66: MEMORY VOLTAGE LOGIC
b) PHASE DISTANCE
PATH: SETTINGS  GROUPED ELEMENTS  SETTING GROUP 1(6)  DISTANCE  PHASE DISTANCE Z1(Z5)
 PHASE DISTANCE Z1 PHS DIST Z1 Range: Disabled, Enabled

PHS DIST Z1 DIR: Range: Forward, Reverse, Non-directional
MESSAGE
Forward
PHS DIST Z1 Range: Mho, Quad
MESSAGE
SHAPE: Mho
PHS DIST Z1 XFMR VOL Range: None, Dy1, Dy3, Dy5, Dy7, Dy9, Dy11, Yd1, Yd3,
MESSAGE Yd5, Yd7, Yd9, Yd11
CONNECTION: None
PHS DIST Z1 XFMR CUR Range: None, Dy1, Dy3, Dy5, Dy7, Dy9, Dy11, Yd1, Yd3,
MESSAGE Yd5, Yd7, Yd9, Yd11
CONNECTION: None
PHS DIST Z1 Range: 0.02 to 500.00 ohms in steps of 0.01
MESSAGE
REACH: 2.00 ohms
PHS DIST Z1 Range: 30 to 90° in steps of 1
MESSAGE
RCA: 85°
PHS DIST Z1 REV Range: 0.02 to 500.00 ohms in steps of 0.01
MESSAGE
REACH: 2.00 ohms

PHS DIST Z1 REV Range: 30 to 90° in steps of 1

MESSAGE
REACH RCA: 85°
MESSAGE
COMP LIMIT: 90°
MESSAGE
DIR RCA: 85°
MESSAGE
DIR COMP LIMIT: 90°
PHS DIST Z1 QUAD Range: 0.02 to 500.00 ohms in steps of 0.01
MESSAGE
RGT BLD: 10.00 ohms
PHS DIST Z1 QUAD Range: 60 to 90° in steps of 1
MESSAGE
RGT BLD RCA: 85°
PHS DIST Z1 QUAD Range: 0.02 to 500.00 ohms in steps of 0.01
MESSAGE
LFT BLD: 10.00 ohms
PHS DIST Z1 QUAD Range: 60 to 90° in steps of 1
MESSAGE
LFT BLD RCA: 85°
PHS DIST Z1 Range: 0.050 to 30.000 pu in steps of 0.001
MESSAGE
SUPV: 0.200 pu
PHS DIST Z1 VOLT Range: 0.000 to 5.000 pu in steps of 0.001
MESSAGE
5
LEVEL: 0.000 pu
PHS DIST Z1 Range: 0.000 to 65.535 s in steps of 0.001
MESSAGE
DELAY: 0.000 s
PHS DIST Z1 BLK: Range: FlexLogic operand
MESSAGE
Off
PHS DIST Z1 Range: Self-reset, Latched, Disabled
MESSAGE
TARGET: Self-reset
PHS DIST Z1 Range: Disabled, Enabled
MESSAGE
EVENTS: Disabled
The phase mho distance function uses a dynamic 100% memory-polarized mho characteristic with additional reactance,
directional, and overcurrent supervising characteristics. When set to “Non-directional”, the mho function becomes an offset
mho with the reverse reach controlled independently from the forward reach, and all the directional characteristics
removed.
The phase quadrilateral distance function is comprised of a reactance characteristic, right and left blinders, and 100%
memory-polarized directional and current supervising characteristics. When set to “Non-directional”, the quadrilateral func-
tion applies a reactance line in the reverse direction instead of the directional comparators. Refer to Chapter 8 for additional
information.
Each phase distance zone is configured individually through its own setting menu. All of the settings can be independently
modified for each of the zones except:
1. The SIGNAL SOURCE setting (common for the distance elements of all zones as entered under SETTINGS  GROUPED
ELEMENTS  SETTING GROUP 1(6)  DISTANCE).
2. The MEMORY DURATION setting (common for the distance elements of all zones as entered under SETTINGS 
GROUPED ELEMENTS  SETTING GROUP 1(6)  DISTANCE).
The common distance settings described earlier must be properly chosen for correct operation of the phase distance ele-
ments. Additional details may be found in chapter 8: Theory of operation.
Although all zones can be used as either instantaneous elements (pickup [PKP] and dropout [DPO] FlexLogic operands) or
time-delayed elements (operate [OP] FlexLogic operands), only zone 1 is intended for the instantaneous under-reaching
tripping mode.

Ensure that the Phase VT Secondary Voltage setting (see the SETTINGS ðò SYSTEM SETUP ð AC
INPUTS ðò VOLTAGE BANK menu) is set correctly to prevent improper operation of associated
memory action.
• PHS DIST Z1 DIR: All phase distance zones are reversible. The forward direction is defined by the PHS DIST Z1 RCA
setting, whereas the reverse direction is shifted 180° from that angle. The non-directional zone spans between the for-
ward reach impedance defined by the PHS DIST Z1 REACH and PHS DIST Z1 RCA settings, and the reverse reach imped-
ance defined by PHS DIST Z1 REV REACH and PHS DIST Z1 REV REACH RCA as illustrated below.
• PHS DIST Z1 SHAPE: This setting selects the shape of the phase distance function between the mho and quadrilat-
eral characteristics. The selection is available on a per-zone basis. The two characteristics and their possible varia-
tions are shown in the following figures.
COMP LIMIT
DIR COMP LIMIT
H
REAC
DIR COMP LIMIT
DIR RCA
RCA
R
5
837720A1.CDR
Figure 5–67: DIRECTIONAL MHO DISTANCE CHARACTERISTIC
COMP LIMIT
R E AC H
RCA
REV REACH
RCA
E AC H
REV R
837802A1.CDR
Figure 5–68: NON-DIRECTIONAL MHO DISTANCE CHARACTERISTIC

COMP LIMIT
COMP LIMIT
DIR COMP LIMIT
REACH
DIR COMP LIMIT
DIR RCA
LFT BLD RCA RCA RGT BLD RCA
R
-LFT BLD RGT BLD
837721A1.CDR
Figure 5–69: DIRECTIONAL QUADRILATERAL PHASE DISTANCE CHARACTERISTIC
COMP LIMIT
COMP LIMIT
5
R E AC H
R
-LFT BLD RGT BLD
REV REACH
R E V R E AC H
RCA
COMP LIMIT
COMP LIMIT
837803A1.CDR
Figure 5–70: NON-DIRECTIONAL QUADRILATERAL PHASE DISTANCE CHARACTERISTIC

X RCA = 80o X RCA = 80o

COMP LIMIT = 90o COMP LIMIT = 90o
DIR RCA = 80o DIR RCA = 80o
DIR COMP LIMIT = 90o DIR COMP LIMIT = 60o
H
REAC
REAC
R R
X RCA = 90o X RCA = 80o

DIR COMP LIMIT = 90o DIR COMP LIMIT = 60o
REACH
H
REAC
R R
837722A1.CDR
Figure 5–71: MHO DISTANCE CHARACTERISTIC SAMPLE SHAPES

5
RCA = 80o RCA = 80o
X DIR COMP LIMIT = 90o X DIR COMP LIMIT = 60o
RGT BLD RCA = 80o RGT BLD RCA = 80o
LFT BLD RCA = 80o LFT BLD RCA = 80o
H
H
REAC
REAC
R R
RCA = 90o RCA = 80o

X DIR COMP LIMIT = 90o X DIR COMP LIMIT = 60o
RGT BLD RCA = 90o RGT BLD RCA = 80o
LFT BLD RCA = 90o LFT BLD RCA = 80o
H
REACH
REAC
R R
837723A1.CDR
Figure 5–72: QUADRILATERAL DISTANCE CHARACTERISTIC SAMPLE SHAPES

• PHS DIST Z1 XFMR VOL CONNECTION: The phase distance elements can be applied to look through a three-phase
delta-wye or wye-delta power transformer. In addition, VTs and CTs could be located independently from one another
at different windings of the transformer. If the potential source is located at the correct side of the transformer, this set-
ting shall be set to “None”.
This setting specifies the location of the voltage source with respect to the involved power transformer in the direction
of the zone. The following figure illustrates the usage of this setting. In section (a), zone 1 is looking through a trans-
former from the delta into the wye winding. Therefore, the Z1 setting shall be set to “Dy11”. In section (b), Zone 4 is
looking through a transformer from the wye into the delta winding. Therefore, the Z4 setting shall be set to “Yd1”. The
zone is restricted by the potential point (location of the VTs) as illustrated in Figure (e).
• PHS DIST Z1 XFMR CUR CONNECTION: This setting specifies the location of the current source with respect to the
involved power transformer in the direction of the zone. In section (a) of the following figure, zone 1 is looking through
a transformer from the delta into the wye winding. Therefore, the Z1 setting shall be set to “Dy11”. In section (b), the
CTs are located at the same side as the read point. Therefore, the Z4 setting shall be set to “None”.
See the Theory of operation chapter for more details, and the Application of settings chapter for information on calcu-
lating distance reach settings in applications involving power transformers.
(a) (b)
delta wye, 330o lag delta wye, 330o lag
Z4 Z4
Z4 XFRM VOL CONNECTION = None Z4 XFRM VOL CONNECTION = Yd1
5
Z4 XFRM CUR CONNECTION = None Z4 XFRM CUR CONNECTION = None
Z1 Z1
Z1 XFRM VOL CONNECTION = Dy11 Z1 XFRM VOL CONNECTION = None

Z1 XFRM CUR CONNECTION = Dy11 Z1 XFRM CUR CONNECTION = Dy11
(c) (e)
delta wye, 330o lag
L1 L2
Z4 Zone 4
Zone 1
Z4 XFRM VOL CONNECTION = None
Z4 XFRM CUR CONNECTION = Yd1 ZL1 ZT ZL2
Z1
Z1 XFRM VOL CONNECTION = Dy11

Z1 XFRM CUR CONNECTION = None
Figure 5–73: APPLICATIONS OF THE PH DIST XFMR VOL/CUR CONNECTION SETTINGS

• PHS DIST Z1 REACH: This setting defines the zone reach for the forward and reverse applications. In the non-direc-
tional applications, this setting defines the forward reach of the zone. The reverse reach impedance in non-directional
applications is set independently. The reach impedance is entered in secondary ohms. The reach impedance angle is
entered as the PHS DIST Z1 RCA setting.
Zone 1 is characterized by transient overreach of less than 5% under source impedance ratios of up to 30. When set-
ting an under-reaching zone 1 for direct tripping and under-reaching pilot schemes (DUTT, PUTT) other factors should
be also considered as per rules of distance relaying. In non-directional applications, this 5% transient accuracy applies
to the forward reach only.

To achieve specified operating speed of distance elements, the relay internally calculates source to line impedance
ratio (SIR) from fault phasors. In these calculations, line impedance is estimated based on the zone 1 reach setting.
Therefore, in order to calculate the SIR value properly and to maintain the optimal operating speed of the distance ele-
ments, you need to set zone 1 reach with a regular 80 to 85% of the line impedance reach setting, even when zone 1
is disabled.
• PHS DIST Z1 RCA: This setting specifies the characteristic angle (similar to the ‘maximum torque angle’ in previous
technologies) of the phase distance characteristic for the forward and reverse applications. In the non-directional appli-
cations, this setting defines the angle of the forward reach impedance. The reverse reach impedance in the non-direc-
tional applications is set independently. The setting is an angle of reach impedance as shown in the distance
characteristic figures shown earlier. This setting is independent from PHS DIST Z1 DIR RCA, the characteristic angle of an
extra directional supervising function.
• PHS DIST Z1 REV REACH: This setting defines the reverse reach of the zone set to non-directional (PHS DIST Z1 DIR
setting). The value must be entered in secondary ohms. This setting does not apply when the zone direction is set to
“Forward” or “Reverse”.
• PHS DIST Z1 REV REACH RCA: This setting defines the angle of the reverse reach impedance if the zone is set to
non-directional (PHS DIST Z1 DIR setting). This setting does not apply when the zone direction is set to “Forward” or
“Reverse”.
• PHS DIST Z1 COMP LIMIT: This setting shapes the operating characteristic. In particular, it produces the lens-type
characteristic of the mho function and a tent-shaped characteristic of the reactance boundary of the quadrilateral func-
tion. If the mho shape is selected, the same limit angle applies to both the mho and supervising reactance compara-
tors. In conjunction with the mho shape selection, the setting improves loadability of the protected line. In conjunction
with the quadrilateral characteristic, this setting improves security for faults close to the reach point by adjusting the
reactance boundary into a tent-shape.
• PHS DIST Z1 DIR RCA: This setting selects the characteristic angle (or maximum torque angle) of the directional
supervising function. If the mho shape is applied, the directional function is an extra supervising function as the 5
dynamic mho characteristic is itself directional. In conjunction with the quadrilateral shape, this setting defines the only
directional function built into the phase distance element. The directional function uses the memory voltage for polar-
ization. This setting typically equals the distance characteristic angle PHS DIST Z1 RCA.
• PHS DIST Z1 DIR COMP LIMIT: Selects the comparator limit angle for the directional supervising function.
• PHS DIST Z1 QUAD RGT BLD: This setting defines the right blinder position of the quadrilateral characteristic along
the resistive axis of the impedance plane (see the Quadrilateral distance characteristic figures). The angular position of
the blinder is adjustable with the use of the PHS DIST Z1 QUAD RGT BLD RCA setting. This setting applies only to the
quadrilateral characteristic and should be set giving consideration to the maximum load current and required resistive
coverage.
• PHS DIST Z1 QUAD RGT BLD RCA: This setting defines the angular position of the right blinder of the quadrilateral
characteristic (see the Quadrilateral distance characteristic figures).
• PHS DIST Z1 QUAD LFT BLD: This setting defines the left blinder position of the quadrilateral characteristic along the
resistive axis of the impedance plane (see the Quadrilateral distance characteristic figures). The angular position of the
blinder is adjustable with the use of the PHS DIST Z1 QUAD LFT BLD RCA setting. This setting applies only to the quadri-
lateral characteristic and should be set with consideration to the maximum load current.
• PHS DIST Z1 QUAD LFT BLD RCA: This setting defines the angular position of the left blinder of the quadrilateral
characteristic (see the Quadrilateral distance characteristic figures).
• PHS DIST Z1 SUPV: The phase distance elements are supervised by the magnitude of the line-to-line current (fault
loop current used for the distance calculations). For convenience, 3 is accommodated by the pickup (that is, before
being used, the entered value of the threshold setting is multiplied by 3 ).
If the minimum fault current level is sufficient, the current supervision pickup should be set above maximum full load
current preventing maloperation under VT fuse fail conditions. This requirement may be difficult to meet for remote
faults at the end of zones 2 and above. If this is the case, the current supervision pickup would be set below the full
load current, but this may result in maloperation during fuse fail conditions.
Zone 1 is sealed-in with the current supervision.
• PHS DIST Z1 VOLT LEVEL: This setting is relevant for applications on series-compensated lines, or in general, if
series capacitors are located between the relaying point and a point where the zone shall not overreach. For plain

(non-compensated) lines, set to zero. Otherwise, the setting is entered in per unit of the phase VT bank configured
under the DISTANCE SOURCE. Effectively, this setting facilitates dynamic current-based reach reduction. In non-direc-
tional applications (PHS DIST Z1 DIR set to “Non-directional”), this setting applies only to the forward reach of the non-
directional zone. See chapters 8 and 9 for information on calculating this setting for series compensated lines.
• PHS DIST Z1 DELAY: This setting allows the user to delay operation of the distance elements and implement stepped
distance protection. The distance element timers for zones 2 and higher apply a short dropout delay to cope with faults
located close to the zone boundary when small oscillations in the voltages or currents could inadvertently reset the
timer. Zone 1 does not need any drop out delay since it is sealed-in by the presence of current.
• PHS DIST Z1 BLK: This setting enables the user to select a FlexLogic operand to block a given distance element. VT
fuse fail detection is one of the applications for this setting.
AND
OR
SETTING
PH DIST Z1 DELAY AND FLEXLOGIC OPERANDS
FLEXLOGIC OPERAND TPKP OR OR PH DIST Z1 OP
PH DIST Z1 PKP AB
0
FLEXLOGIC OPERAND TPKP
PH DIST Z1 PKP BC
0 AND
FLEXLOGIC OPERAND TPKP OR
PH DIST Z1 PKP CA
0 FLEXLOGIC OPERANDS
PH DIST Z1 OP AB
PH DIST Z1 OP BC
AND
FLEXLOGIC OPERANDS PH DIST Z1 OP CA
5 PH DIST Z1 SUPN IAB

PH DIST Z1 SUPN IBC
PH DIST Z1 SUPN ICA
AND
AND
OPEN POLE OP **
** D60, L60, and L90 only. Other UR-series models apply regular current seal-in for zone 1. 837017A8.CDR
Figure 5–74: PHASE DISTANCE ZONE 1 OP SCHEME
IURPWKHRSHQSROHHOHPHQW '/DQG/RQO\
)/(;/2*,&23(5$1'
23(132/(23
)/(;/2*,&23(5$1' 6(77,1* )/(;/2*,&23(5$1'

7,0(5 3+',67='(/$< $1' 3+',67=23$%
3+',67=3.3$%
PV $1'
73.3
25
25
PV
)/(;/2*,&23(5$1' 6(77,1* )/(;/2*,&23(5$1'

7,0(5
3+',67=3.3%& 3+',67='(/$< $1' 3+',67=23%&
PV $1'
25 73.3
PV 25

)/(;/2*,&23(5$1'
7,0(5 )/(;/2*,&23(5$1'
3+',67=3.3&$ 6(77,1*
PV $1' $1' 3+',67=23&$
3+',67='(/$<
25
IURPWKHWULSRXWSXWHOHPHQW 25
73.3
PV
)/(;/2*,&23(5$1'
)/(;/2*,&23(5$1'
75,3=3+705,1,7
25 3+',67=23
$&'5
Figure 5–75: PHASE DISTANCE ZONE 2 OP SCHEME

For phase distance zone 2, there is a provision to start the zone timer with other distance zones or loop the pickup
flag to avoid prolonging phase distance zone 2 operation when the fault evolves from one type to another or
NOTE migrates from the initial zone to zone 2. Desired zones in the trip output function should be assigned to accomplish
this functionality.

)/(;/2*,&23(5$1'
23(132/(23
7,0(5 6(77,1*
)/(;/2*,&23(5$1' PV 3+',67='(/$<
$1' )/(;/2*,&23(5$1'
3+',67=3.3$% 73.3
PV 25 3+',67=23$%

7,0(5 6(77,1*
)/(;/2*,&23(5$1' PV 3+',67='(/$<
$1' )/(;/2*,&23(5$1'
3+',67=3.3%& 73.3
PV 25 3+',67=23%&

7,0(5 6(77,1*
)/(;/2*,&23(5$1' PV 3+',67='(/$<
$1' )/(;/2*,&23(5$1'
3+',67=3.3&$ 73.3
PV 25 3+',67=23&$

)/(;/2*,&23(5$1'
25 3+',67=23
'/DQG/RQO\ $$&'5
Figure 5–76: PHASE DISTANCE ZONES 3 AND HIGHER OP SCHEME
D60, L60, and L90 only

FLEXLOGIC OPERANDS
OPEN POLE BLK AB
OPEN POLE BLK BC
OPEN POLE BLK CA
SETTINGS
PH DIST Z1 DIR
PH DIST Z1 SHAPE
PH DIST Z1 XFMR
VOL CONNECTION
5
SETTING PH DIST Z1 XFMR
PH DIST Z1 FUNCTION CUR CONNECTION
Enabled = 1 PH DIST Z1 REACH
PH DIST Z1 RCA
PH DIST Z1 REV REACH
AND PH DIST Z1 REV REACH RCA
SETTING
PH DIST Z1 COMP LIMIT
PH DIST Z1 BLK
PH DIST Z1 QUAD RGT BLD
Off = 0
PH DIST Z1 QUAD RGT BLD RCA Quadrilateral
PH DIST Z1 QUAD LFT BLD characteristic only
PH DIST Z1 QUAD LFT BLD RCA
SETTING PH DIST Z1 VOLT LEVEL FLEXLOGIC OPERANDS
DISTANCE SOURCE RUN AND PH DIST Z1 PKP AB
IA-IB PH DIST Z1 DPO AB
A-B ELEMENT
IB-IC
IC-IA RUN FLEXLOGIC OPERANDS
VAG-VBG B-C ELEMENT AND PH DIST Z1 PKP BC
Wye
VTs
VBG-VCG PH DIST Z1 DPO BC

VCG-VAG RUN
VAB C-A ELEMENT FLEXLOGIC OPERANDS
Delta
VTs
VBC AND PH DIST Z1 PKP CA

VCA PH DIST Z1 DPO CA
V_1 MEMORY
I_1
TIMER FLEXLOGIC OPERAND
V_1 > 0.80 pu 1 cycle OR PH DIST Z1 PKP
OR
I_1 > 0.025 pu 1 cycle
SETTING
PHS DIST Z1 SUPV
RUN FLEXLOGIC OPERAND
| IA – IB | > 3 × Pickup PH DIST Z1 SUPN IAB

| IB – IC | > 3 × Pickup PH DIST Z1 SUPN IBC

| IC – IA | > 3 × Pickup PH DIST Z1 SUPN ICA
837002AM.CDR
Figure 5–77: PHASE DISTANCE SCHEME LOGIC

c) GROUND DISTANCE
PATH: SETTINGS  GROUPED ELEMENTS  SETTING GROUP 1(6)  DISTANCE  GROUND DISTANCE Z1(Z5)
 GROUND DISTANCE Z1 GND DIST Z1 Range: Disabled, Enabled

GND DIST Z1 DIR: Range: Forward, Reverse, Non-directional
MESSAGE
Forward
GND DIST Z1 Range: Mho, Quad
MESSAGE
SHAPE: Mho
GND DIST Z1 Range: 0.00 to 10.00 in steps of 0.01
MESSAGE
Z0/Z1 MAG: 2.70
GND DIST Z1 Range: –90 to 90° in steps of 1
MESSAGE
Z0/Z1 ANG: 0°
GND DIST Z1 Range: 0.00 to 7.00 in steps of 0.01
MESSAGE
ZOM/Z1 MAG: 0.00
GND DIST Z1 Range: –90 to 90° in steps of 1
MESSAGE
ZOM/Z1 ANG: 0°
GND DIST Z1 Range: 0.02 to 500.00 ohms in steps of 0.01
MESSAGE
REACH: 2.00 
GND DIST Z1 Range: 30 to 90° in steps of 1
MESSAGE
RCA: 85°
5 GND DIST Z1 REV Range: 0.02 to 500.00 ohms in steps of 0.01
MESSAGE
REACH: 2.00 
GND DIST Z1 REV Range: 30 to 90° in steps of 1
MESSAGE
REACH RCA: 85°
GND DIST Z1 POL Range: Zero-seq, Neg-seq
MESSAGE
CURRENT: Zero-seq
GND DIST Z1 NON- Range: –40.0 to 40.0° in steps of 0.1
MESSAGE
HOMOGEN ANG: 0.0°
MESSAGE
COMP LIMIT: 90°
MESSAGE
DIR RCA: 85°
MESSAGE
DIR COMP LIMIT: 90°
GND DIST Z1 QUAD Range: 0.02 to 500.00 ohms in steps of 0.01
MESSAGE
RGT BLD: 10.00 
GND DIST Z1 QUAD Range: 60 to 90° in steps of 1
MESSAGE
RGT BLD RCA: 85°
GND DIST Z1 QUAD Range: 0.02 to 500.00 ohms in steps of 0.01
MESSAGE
LFT BLD: 10.00 
GND DIST Z1 QUAD Range: 60 to 90° in steps of 1
MESSAGE
LFT BLD RCA: 85°
GND DIST Z1 Range: 0.050 to 30.000 pu in steps of 0.001
MESSAGE
SUPV: 0.200 pu

GND DIST Z1 VOLT Range: 0.000 to 5.000 pu in steps of 0.001

MESSAGE
LEVEL: 0.000 pu
GND DIST Z1 Range: 0.000 to 65.535 s in steps of 0.001
MESSAGE
DELAY: 0.000 s
GND DIST Z1 BLK: Range: FlexLogic operand
MESSAGE
Off
GND DIST Z1 Range: Self-Rest, Latched, Disabled
MESSAGE
TARGET: Self-Reset
GND DIST Z1 Range: Disabled, Enabled
MESSAGE
EVENTS: Disabled
The ground mho distance function uses a dynamic 100% memory-polarized mho characteristic with additional reactance,
directional, current, and phase selection supervising characteristics. The ground quadrilateral distance function is com-
posed of a reactance characteristic, right and left blinders, and 100% memory-polarized directional, overcurrent, and phase
selection supervising characteristics.
When set to non-directional, the mho function becomes an offset mho with the reverse reach controlled independently from
the forward reach, and all the directional characteristics removed. When set to non-directional, the quadrilateral function
applies a reactance line in the reverse direction instead of the directional comparators.
The reactance supervision for the mho function uses the zero-sequence current for polarization. The reactance line of the
quadrilateral function uses either zero-sequence or negative-sequence current as a polarizing quantity. The selection is
controlled by a user setting and depends on the degree of non-homogeneity of the zero-sequence and negative-sequence
equivalent networks.
The directional supervision uses memory voltage as polarizing quantity and both zero- and negative-sequence currents as 5
operating quantities.
The phase selection supervision restrains the ground elements during double-line-to-ground faults as they – by principles
of distance relaying – may be inaccurate in such conditions. Ground distance zones 2 and higher apply additional zero-
sequence directional supervision. See chapter 8 for additional details.
Each ground distance zone is configured individually through its own setting menu. All of the settings can be independently
modified for each of the zones except:
1. The SIGNAL SOURCE setting (common for both phase and ground elements for all zones as entered under the SETTINGS
 GROUPED ELEMENTS  SETTING GROUP 1(6)  DISTANCE menu).
2. The MEMORY DURATION setting (common for both phase and ground elements for all zones as entered under the SET-
TINGS  GROUPED ELEMENTS  SETTING GROUP 1(6)  DISTANCE menu).
The common distance settings noted at the start of this section must be properly chosen for correct operation of the ground
distance elements.
Although all ground distance zones can be used as either instantaneous elements (pickup [PKP] and dropout [DPO] Flex-
Logic signals) or time-delayed elements (operate [OP] FlexLogic signals), only zone 1 is intended for the instantaneous
under-reaching tripping mode.
Ensure that the PHASE VT SECONDARY VOLTAGE (see the SETTINGS  SYSTEM SETUP  AC INPUTS  VOLTAGE
BANK menu) is set correctly to prevent improper operation of associated memory action.
NOTE
• GND DIST Z1 DIR: All ground distance zones are reversible. The forward direction is defined by the GND DIST Z1 RCA
setting and the reverse direction is shifted by 180° from that angle. The non-directional zone spans between the for-
ward reach impedance defined by the GND DIST Z1 REACH and GND DIST Z1 RCA settings, and the reverse reach imped-
ance defined by the GND DIST Z1 REV REACH and GND DIST Z1 REV REACH RCA settings.
• GND DIST Z1 SHAPE: This setting selects the shape of the ground distance characteristic between the mho and
quadrilateral characteristics. The selection is available on a per-zone basis.
The directional and non-directional quadrilateral ground distance characteristics are shown below. The directional and
non-directional mho ground distance characteristics are the same as those shown for the phase distance element in
the previous sub-section.

X
"+" NON-HOMOGEN. ANG
"-" NON-HOMOGEN. ANG
COMP LIMIT COMP LIMIT
DIR COMP LIMIT
REACH
DIR COMP LIMIT
DIR RCA
R
-LFT BLD RGT BLD
837769A1.CDR
Figure 5–78: DIRECTIONAL QUADRILATERAL GROUND DISTANCE CHARACTERISTIC
X
5
REACH
R
-LFT BLD RGT BLD
RE V REACH
REV REACH
RCA

837770A1.CDR
Figure 5–79: NON-DIRECTIONAL QUADRILATERAL GROUND DISTANCE CHARACTERISTIC

• GND DIST Z1 Z0/Z1 MAG: This setting specifies the ratio between the zero-sequence and positive-sequence imped-
ance required for zero-sequence compensation of the ground distance elements. This setting is available on a per-
zone basis, enabling precise settings for tapped, non-homogeneous, and series compensated lines.
• GND DIST Z1 Z0/Z1 ANG: This setting specifies the angle difference between the zero-sequence and positive-
sequence impedance required for zero-sequence compensation of the ground distance elements. The entered value is
the zero-sequence impedance angle minus the positive-sequence impedance angle. This setting is available on a per-
zone basis, enabling precise values for tapped, non-homologous, and series-compensated lines.
• GND DIST Z1 ZOM/Z1 MAG: The ground distance elements can be programmed to apply compensation for the zero-
sequence mutual coupling between parallel lines. If this compensation is required, the ground current from the parallel
line (3I_0) measured in the direction of the zone being compensated must be connected to the ground input CT of the
CT bank configured under the DISTANCE SOURCE. This setting specifies the ratio between the magnitudes of the mutual
zero-sequence impedance between the lines and the positive-sequence impedance of the protected line. It is impera-
tive to set this setting to zero if the compensation is not to be performed.

• GND DIST Z1 ZOM/Z1 ANG: This setting specifies the angle difference between the mutual zero-sequence imped-
ance between the lines and the positive-sequence impedance of the protected line.
• GND DIST Z1 REACH: This setting defines the reach of the zone for the forward and reverse applications. In non-
directional applications, this setting defines the forward reach of the zone. The reverse reach impedance in non-direc-
tional applications is set independently. The angle of the reach impedance is entered as the GND DIST Z1 RCA setting.
The reach impedance is entered in secondary ohms.
To achieve specified operating speed of distance elements, the relay internally calculates source to line impedance
ratio (SIR) from fault phasors. In these calculations, line impedance is estimated based on the zone 1 reach setting.
Therefore, in order to calculate the SIR value properly and to maintain the optimal operating speed of the distance ele-
ments, you need to set zone 1 reach with a regular 80 to 85% of the line impedance reach setting, even when zone 1
is disabled.
• GND DIST Z1 RCA: This setting specifies the characteristic angle (similar to the maximum torque angle in previous
technologies) of the ground distance characteristic for the forward and reverse applications. In the non-directional
applications this setting defines the forward reach of the zone. The reverse reach impedance in the non-directional
applications is set independently. This setting is independent from the GND DIST Z1 DIR RCA setting (the characteristic
angle of an extra directional supervising function).
The relay internally performs zero-sequence compensation for the protected circuit based on the values
entered for GND DIST Z1 Z0/Z1 MAG and GND DIST Z1 Z0/Z1 ANG, and if configured to do so, zero-sequence com-
NOTE
pensation for mutual coupling based on the values entered for GND DIST Z1 Z0M/Z1 MAG and GND DIST Z1 Z0M/Z1
ANG. The GND DIST Z1 REACH and GND DIST Z1 RCA should, therefore, be entered in terms of positive sequence
quantities. Refer to chapters 8 for additional information
• GND DIST Z1 REV REACH: This setting defines the reverse reach of the zone set to non-directional (GND DIST Z1 DIR
setting). The value must be entered in secondary ohms. This setting does not apply when the zone direction is set to
“Forward” or “Reverse”.
5
• GND DIST Z1 REV REACH RCA: This setting defines the angle of the reverse reach impedance if the zone is set to
non-directional (GND DIST Z1 DIR setting). This setting does not apply when the zone direction is set to “Forward” or
“Reverse”.
• GND DIST Z1 POL CURRENT: This setting applies only if the GND DIST Z1 SHAPE is set to “Quad” and controls the
polarizing current used by the reactance comparator of the quadrilateral characteristic. Either the zero-sequence or
negative-sequence current could be used. In general, a variety of system conditions must be examined to select an
optimum polarizing current. This setting becomes less relevant when the resistive coverage and zone reach are set
conservatively. Also, this setting is more relevant in lower voltage applications such as on distribution lines or cables,
as compared with high-voltage transmission lines. This setting applies to both the zone 1 and reverse reactance lines
if the zone is set to non-directional. Refer to chapters 8 and 9 for additional information.
• GND DIST Z1 NON-HOMOGEN ANG: This setting applies only if the GND DIST Z1 SHAPE is set to “Quad” and provides
a method to correct the angle of the polarizing current of the reactance comparator for non-homogeneity of the zero-
sequence or negative-sequence networks. In general, a variety of system conditions must be examined to select this
setting. In many applications this angle is used to reduce the reach at high resistances in order to avoid overreaching
under far-out reach settings and/or when the sequence networks are greatly non-homogeneous. This setting applies to
both the forward and reverse reactance lines if the zone is set to non-directional. Refer to chapters 8 and 9 for addi-
tional information.
• GND DIST Z1 COMP LIMIT: This setting shapes the operating characteristic. In particular, it enables a lens-shaped
characteristic of the mho function and a tent-shaped characteristic of the quadrilateral function reactance boundary. If
the mho shape is selected, the same limit angle applies to mho and supervising reactance comparators. In conjunction
with the mho shape selection, this setting improves loadability of the protected line. In conjunction with the quadrilat-
eral characteristic, this setting improves security for faults close to the reach point by adjusting the reactance boundary
into a tent-shape.
• GND DIST Z1 DIR RCA: Selects the characteristic angle (or ‘maximum torque angle’) of the directional supervising
function. If the mho shape is applied, the directional function is an extra supervising function, as the dynamic mho
characteristic itself is a directional one. In conjunction with the quadrilateral shape selection, this setting defines the
only directional function built into the ground distance element. The directional function uses memory voltage for polar-
ization.
• GND DIST Z1 DIR COMP LIMIT: This setting selects the comparator limit angle for the directional supervising function.

• GND DIST Z1 QUAD RGT BLD: This setting defines the right blinder position of the quadrilateral characteristic along
the resistive axis of the impedance plane (see the Quadrilateral distance characteristic figure). The angular position of
the blinder is adjustable with the use of the GND DIST Z1 QUAD RGT BLD RCA setting. This setting applies only to the
quadrilateral characteristic and should be set with consideration to the maximum load current and required resistive
coverage.
• GND DIST Z1 QUAD RGT BLD RCA: This setting defines the angular position of the right blinder of the quadrilateral
characteristic (see the Quadrilateral distance characteristic figure).
• GND DIST Z1 QUAD LFT BLD: This setting defines the left blinder position of the quadrilateral characteristic along the
resistive axis of the impedance plane (see the Quadrilateral distance characteristic figure). The angular position of the
blinder is adjustable with the use of the GND DIST Z1 QUAD LFT BLD RCA setting. This setting applies only to the quadri-
lateral characteristic and should be set with consideration to the maximum load current.
• GND DIST Z1 QUAD LFT BLD RCA: This setting defines the angular position of the left blinder of the quadrilateral
characteristic (see the Quadrilateral distance characteristic figure).
• GND DIST Z1 SUPV: The ground distance elements are supervised by the magnitude of the neutral (3I_0) current.
The current supervision pickup should be set less than the minimum 3I_0 current for the end of the zone fault, taking
into account the desired fault resistance coverage to prevent maloperation due to VT fuse failure. Settings less than
0.2 pu are not recommended and should be applied with caution. To enhance ground distance security against spuri-
ous neutral current during switch-off transients, three-phase faults, and phase-to-phase faults, a positive-sequence
current restraint of 5% is applied to the neutral current supervision magnitude. This setting should be at least three
times the CURRENT CUTOFF LEVEL setting specified in the PRODUCT SETUP  DISPLAY PROPERTIES menu
Zone 1 is sealed in with the current supervision.
• GND DIST Z1 VOLT LEVEL: This setting is relevant for applications on series-compensated lines, or in general, if
series capacitors are located between the relaying point and a point for which the zone shall not overreach. For plain
5 (non-compensated) lines, this setting shall be set to zero. Otherwise, the setting is entered in per unit of the VT bank
configured under the DISTANCE SOURCE. Effectively, this setting facilitates dynamic current-based reach reduction. In
non-directional applications (GND DIST Z1 DIR set to “Non-directional”), this setting applies only to the forward reach of
the non-directional zone. See chapters 8 and 9 for additional details and information on calculating this setting value
for applications on series compensated lines.
• GND DIST Z1 DELAY: This setting enables the user to delay operation of the distance elements and implement a
stepped distance backup protection. The distance element timer applies a short drop out delay to cope with faults
located close to the boundary of the zone when small oscillations in the voltages or currents could inadvertently reset
the timer.
• GND DIST Z1 BLK: This setting enables the user to select a FlexLogic operand to block the given distance element.
VT fuse fail detection is one of the applications for this setting.
FLEXLOGIC OPERANDS
GND DIST Z1 OP A
SETTING GND DIST Z1 OP B
GND DIST Z1 DELAY AND GND DIST Z1 OP C
FLEXLOGIC OPERAND TPKP OR
GND DIST Z1 PKP A
0
GND DIST Z1 PKP B
0 FLEXLOGIC OPERAND
AND
OR OR GND DIST Z1 OP
GND DIST Z1 PKP C
0
FLEXLOGIC OPERANDS
GND DIST Z1 SUPN IN AND
AND
OPEN POLE OP ** OR
** D60, L60, and L90 only. Other UR-series models apply regular current seal-in for zone 1. 837018A7.CDR
Figure 5–80: GROUND DISTANCE ZONE 1 OP SCHEME

IURPWKHRSHQSROHGHWHFWRUHOHPHQW'/DQG/RQO\
)/(;/2*,&23(5$1'
23(132/(23
)/(;/2*,&23(5$1' 6(77,1* )/(;/2*,&23(5$1'

7,0(5 *1'',67='(/$< $1' *1'',67=23$
*1'',67=3.3$
PV $1'
73.3
25
25
PV
)/(;/2*,&23(5$1' 6(77,1* )/(;/2*,&23(5$1'

7,0(5
*1'',67=3.3% *1'',67='(/$< $1' *1'',67=23%
PV $1'
25 73.3
PV 25

)/(;/2*,&23(5$1'
7,0(5 )/(;/2*,&23(5$1'
*1'',67=3.3& 6(77,1*
PV $1' $1' *1'',67=23&
*1'',67='(/$<
25
25
73.3
IURPWKHWULSRXWSXWHOHPHQW PV
)/(;/2*,&23(5$1'
)/(;/2*,&23(5$1'
75,3=*5705,1,7
25 *1'',67=23
$&'5
Figure 5–81: GROUND DISTANCE ZONE 2 OP SCHEME

For ground distance zone 2, there is a provision to start the zone timer with the other distance zones or loop pickup
flags to avoid prolonging ground distance zone 2 operation if the fault evolves from one type to another or migrates
NOTE from zone 3 or 4 to zone 2. The desired zones should be assigned in the trip output element to accomplish this
functionality.
)/(;/2*,&23(5$1'
23(132/(23
5
7,0(5 6(77,1*
)/(;/2*,&23(5$1' PV *1'',67='(/$<
$1' )/(;/2*,&23(5$1'
*1'',67=3.3$ 73.3
PV 25 *1'',67=23$

7,0(5 6(77,1*
)/(;/2*,&23(5$1' PV *1'',67='(/$<
$1' )/(;/2*,&23(5$1'
*1'',67=3.3% 73.3
PV 25 *1'',67=23%

7,0(5 6(77,1*
)/(;/2*,&23(5$1' PV *1'',67='(/$<
$1' )/(;/2*,&23(5$1'
*1'',67=3.3& 73.3
PV 25 *1'',67=23&

)/(;/2*,&23(5$1'
25 *1'',67=23
'/DQG/RQO\ $$&'5
Figure 5–82: GROUND DISTANCE ZONES 3 AND HIGHER OP SCHEME


FLEXLOGIC OPERANDS
OPEN POLE OP ФA
OPEN POLE OP ФB
OPEN POLE OP ФC
SETTINGS
GND DIST Z1 DIR
GND DIST Z1 SHAPE
GND DIST Z1 Z0/Z1 MAG
GND DIST Z1 Z0/Z1 ANG
GND DIST Z1 ZOM/Z1 MAG
GND DIST Z1 ZOM/Z1 ANG
GND DIST Z1 REACH
GND DIST Z1 RCA
GND DIST Z1 REV REACH
SETTING
GND DIST Z1 FUNCTION GND DIST Z1 REV REACH RCA
Enabled = 1 GND DIST Z1 POL CURRENT
GND DIST Z1 NON-HOMGEN ANG
GND DIST Z1 COMP LIMIT
AND GND DIST Z1 DIR RCA
SETTING
GND DIST Z1 DIR COMP LIMIT
GND DIST Z1 BLK
GND DIST Z1 VOLT LEVEL
Off = 0
GND DIST Z1 QUAD RGT BLD
Quadrilateral
GND DIST Z1 QUAD RGT BLD RCA characteristic
GND DIST Z1 QUAD LFT BLD only
SETTING GND DIST Z1 QUAD LFT BLD RCA
DISTANCE SOURCE RUN
IA
IB FLEXLOGIC OPERANDS
A ELEMENT
IC AND GND DIST Z1 PKP A
VAG GND DIST Z1 DPO A
RUN
Wye
VTs
VBG
VCG FLEXLOGIC OPERANDS
B ELEMENT
I_2 AND GND DIST Z1 PKP B
I_0 GND DIST Z1 DPO B
V_1 RUN
5 I_1
IN
MEMORY
C ELEMENT
AND
FLEXLOGIC OPERANDS
GND DIST Z1 PKP C
GND DIST Z1 DPO C
TIMER FLEXLOGIC OPERAND

V_1 > 0.80 pu 1 cycle OR GND DIST Z1 PKP
OR
1 cycle
I_1 > 0.025 pu
SETTING
GND DIST Z1 SUPV
| IN – 0.05 × I_1 | > Pickup GND DIST Z1 SUPN IN
837007AH.CDR
Figure 5–83: GROUND DISTANCE ZONE 1 SCHEME LOGIC


FLEXLOGIC OPERANDS
OPEN POLE OP ФA
OPEN POLE OP ФB
OPEN POLE OP ФC
SETTINGS
GND DIST Z2 DIR
GND DIST Z2 SHAPE
GND DIST Z2 Z0/Z2 MAG
GND DIST Z2 Z0/Z2 ANG
GND DIST Z2 ZOM/Z1 MAG
GND DIST Z2 ZOM/Z1 ANG
GND DIST Z2 REACH
GND DIST Z2 RCA
GND DIST Z2 REV REACH
SETTING
GND DIST Z2 FUNCTION GND DIST Z2 REV REACH RCA
Enabled = 1 GND DIST Z2 POL CURRENT
GND DIST Z2 NON-HOMGEN ANG
GND DIST Z2 COMP LIMIT
AND GND DIST Z2 DIR RCA
SETTING
GND DIST Z2 DIR COMP LIMIT
GND DIST Z2 BLK
GND DIST Z2 VOLT LEVEL
Off = 0
GND DIST Z2 QUAD RGT BLD
Quadrilateral
GND DIST Z2 QUAD RGT BLD RCA characteristic
GND DIST Z2 QUAD LFT BLD only
SETTING GND DIST Z2 QUAD LFT BLD RCA
DISTANCE SOURCE RUN
IA
IB A ELEMENT FLEXLOGIC OPERANDS
IC AND GND DIST Z2 PKP A
VAG GND DIST Z2 DPO A
RUN
Wye
VTs
VBG
VCG
B ELEMENT FLEXLOGIC OPERANDS
I_2
AND GND DIST Z2 PKP B
I_0
GND DIST Z2 DPO B
V_1 RUN
I_1
IN C ELEMENT
AND
FLEXLOGIC OPERANDS
GND DIST Z2 PKP C
5
MEMORY
GND DIST Z2 DPO C
TIMER
V_1 > 0.80 pu 1 cycle FLEXLOGIC OPERAND
OR GND DIST Z2 PKP
OR
1 cycle
I_1 > 0.025 pu
SETTING
GND DIST Z2 SUPV
| IN – 0.05 × I_1 | > Pickup GND DIST Z2 SUPN IN
GND DIST Z2 DIR SUPN
OR
OPEN POLE OP **
** D60, L60, and L90 only 837011AL.CDR
Figure 5–84: GROUND DISTANCE ZONES 2 AND HIGHER SCHEME LOGIC

GROUND DIRECTIONAL SUPERVISION:
A dual (zero-sequence and negative-sequence) memory-polarized directional supervision applied to the ground distance
protection elements has been shown to give good directional integrity. However, a reverse double-line-to-ground fault can
lead to a maloperation of the ground element in a sound phase if the zone reach setting is increased to cover high resis-
tance faults.
Ground distance zones 2 and higher use an additional ground directional supervision to enhance directional integrity. The
element’s directional characteristic angle is used as a maximum torque angle together with a 90° limit angle.
The supervision is biased toward operation in order to avoid compromising the sensitivity of ground distance elements at
low signal levels. Otherwise, the reverse fault condition that generates concern will have high polarizing levels so that a cor-
rect reverse fault decision can be reliably made.
The supervision for zones 2 and 5 is removed during open pole conditions.

V_0 > 5 volts
SETTING
Distance Source RUN
= V_0 OR
Zero-sequence
FLEXLOGIC OPERAND
= I_0 directional characteristic
TIMER AND GND DIST Z2 DIR SUPN
tpickup
FLEXLOGIC OPERAND
OPEN POLE OP treset
Co-ordinating time:
pickup = 1.0 cycle, reset = 1.0 cycle 837009A7.CDR
Figure 5–85: GROUND DIRECTIONAL SUPERVISION SCHEME LOGIC
5.6.5 POWER SWING DETECT
PATH: SETTINGS  GROUPED ELEMENTS  SETTING GROUP 1(6)  POWER SWING DETECT
 POWER SWING POWER SWING Range: Disabled, Enabled

 DETECT FUNCTION: Disabled
POWER SWING Range: SRC 1, SRC 2, SRC 3, SRC 4
MESSAGE
SOURCE: SRC 1
POWER SWING Range: Mho Shape, Quad Shape
MESSAGE
SHAPE: Mho Shape
POWER SWING Range: Two Step, Three Step
MESSAGE
MODE: Two Step
5 MESSAGE
POWER SWING Range: 0.050 to 30.000 pu in steps of 0.001
SUPV: 0.600 pu
POWER SWING FWD Range: 0.10 to 500.00 ohms in steps of 0.01
MESSAGE
REACH: 50.00 
POWER SWING QUAD FWD Range: 0.10 to 500.00 ohms in steps of 0.01
MESSAGE
REACH MID: 60.00 
POWER SWING QUAD FWD Range: 0.10 to 500.00 ohms in steps of 0.01
MESSAGE
REACH OUT: 70.00 
POWER SWING FWD Range: 40 to 90° in steps of 1
MESSAGE
RCA: 75°
POWER SWING REV Range: 0.10 to 500.00 ohms in steps of 0.01
MESSAGE
REACH: 50.00 
POWER SWING QUAD REV Range: 0.10 to 500.00 ohms in steps of 0.01
MESSAGE
REACH MID: 60.00 
POWER SWING QUAD REV Range: 0.10 to 500.00 ohms in steps of 0.01
MESSAGE
REACH OUT: 70.00 
POWER SWING REV Range: 40 to 90° in steps of 1
MESSAGE
RCA: 75°
POWER SWING OUTER Range: 40 to 140° in steps of 1
MESSAGE
LIMIT ANGLE: 120°
POWER SWING MIDDLE Range: 40 to 140° in steps of 1
MESSAGE
LIMIT ANGLE: 90°
POWER SWING INNER Range: 40 to 140° in steps of 1
MESSAGE
LIMIT ANGLE: 60°

POWER SWING OUTER Range: 0.10 to 500.00 ohms in steps of 0.01

MESSAGE
RGT BLD: 100.00 
POWER SWING OUTER Range: 0.10 to 500.00 ohms in steps of 0.01
MESSAGE
LFT BLD: 100.00 
POWER SWING MIDDLE Range: 0.10 to 500.00 ohms in steps of 0.01
MESSAGE
RGT BLD: 100.00 
POWER SWING MIDDLE Range: 0.10 to 500.00 ohms in steps of 0.01
MESSAGE
LFT BLD: 100.00 
POWER SWING INNER Range: 0.10 to 500.00 ohms in steps of 0.01
MESSAGE
RGT BLD: 100.00 
POWER SWING INNER Range: 0.10 to 500.00 ohms in steps of 0.01
MESSAGE
LFT BLD: 100.00 
POWER SWING PICKUP Range: 0.000 to 65.535 s in steps of 0.001
MESSAGE
DELAY 1: 0.030 s
POWER SWING RESET Range: 0.000 to 65.535 s in steps of 0.001
MESSAGE
DELAY 1: 0.050 s
MESSAGE
DELAY 2: 0.017 s
MESSAGE
DELAY 3: 0.009 s
POWER SWING PICKUP Range: 0.000 to 65.535 s in steps of 0.001 5
MESSAGE
DELAY 4: 0.017 s
POWER SWING SEAL-IN Range: 0.000 to 65.535 s in steps of 0.001
MESSAGE
DELAY: 0.400 s
POWER SWING TRIP Range: Early, Delayed
MESSAGE
MODE: Delayed
POWER SWING BLK: Range: Flexlogic operand
MESSAGE
Off
POWER SWING Range: Self-Reset, Latched, Disabled
MESSAGE
TARGET: Self-Reset
POWER SWING Range: Disabled, Enabled
MESSAGE
EVENTS: Disabled
The power swing detect element provides both power swing blocking and out-of-step tripping functions. The element mea-
sures the positive-sequence apparent impedance and traces its locus with respect to either two or three user-selectable
operating characteristic boundaries. Upon detecting appropriate timing relations, the blocking and tripping indications are
given through FlexLogic operands. The element incorporates an adaptive disturbance detector. This function does not trig-
ger on power swings, but is capable of detecting faster disturbances – faults in particular – that may occur during power
swings. Operation of this dedicated disturbance detector is signaled via the POWER SWING 50DD operand.
The power swing detect element asserts two outputs intended for blocking selected protection elements on power swings:
POWER SWING BLOCK is a traditional signal that is safely asserted for the entire duration of the power swing, and POWER
SWING UN/BLOCK is established in the same way, but resets when an extra disturbance is detected during the power swing.
The POWER SWING UN/BLOCK operand may be used for blocking selected protection elements if the intent is to respond to
faults during power swing conditions.
Different protection elements respond differently to power swings. If tripping is required for faults during power swing condi-
tions, some elements may be blocked permanently (using the POWER SWING BLOCK operand), and others may be blocked
and dynamically unblocked upon fault detection (using the POWER SWING UN/BLOCK operand).

The operating characteristic and logic figures should be viewed along with the following discussion to develop an under-
standing of the operation of the element.
The power swing detect element operates in three-step or two-step mode:
• Three-step operation: The power swing blocking sequence essentially times the passage of the locus of the positive-
sequence impedance between the outer and the middle characteristic boundaries. If the locus enters the outer charac-
teristic (indicated by the POWER SWING OUTER FlexLogic operand) but stays outside the middle characteristic (indi-
cated by the POWER SWING MIDDLE FlexLogic operand) for an interval longer than POWER SWING PICKUP DELAY 1, the
power swing blocking signal (POWER SWING BLOCK FlexLogic operand) is established and sealed-in. The blocking sig-
nal resets when the locus leaves the outer characteristic, but not sooner than the POWER SWING RESET DELAY 1 time.
• Two-step operation: If the two-step mode is selected, the sequence is identical, but it is the outer and inner character-
istics that are used to time the power swing locus.
The out-of-step tripping feature operates as follows for three-step and two-step power swing detection modes:
• Three-step operation: The out-of-step trip sequence identifies unstable power swings by determining if the imped-
ance locus spends a finite time between the outer and middle characteristics and then a finite time between the middle
and inner characteristics. The first step is similar to the power swing blocking sequence. After timer POWER SWING
PICKUP DELAY 1 times out, latch 1 is set as long as the impedance stays within the outer characteristic.
If afterwards, at any time (given the impedance stays within the outer characteristic), the locus enters the middle char-
acteristic but stays outside the inner characteristic for a period of time defined as POWER SWING PICKUP DELAY 2, latch
2 is set as long as the impedance stays inside the outer characteristic. If afterwards, at any time (given the impedance
stays within the outer characteristic), the locus enters the inner characteristic and stays there for a period of time
defined as POWER SWING PICKUP DELAY 3, latch 2 is set as long as the impedance stays inside the outer characteristic;
the element is now ready to trip.
5 If the "Early" trip mode is selected, the POWER SWING TRIP operand is set immediately and sealed-in for the interval
set by the POWER SWING SEAL-IN DELAY. If the "Delayed" trip mode is selected, the element waits until the impedance
locus leaves the inner characteristic, then times out the POWER SWING PICKUP DELAY 2 and sets Latch 4; the element is
now ready to trip. The trip operand is set later, when the impedance locus leaves the outer characteristic.
• Two-step operation: The two-step mode of operation is similar to the three-step mode with two exceptions. First, the
initial stage monitors the time spent by the impedance locus between the outer and inner characteristics. Second, the
stage involving the POWER SWING PICKUP DELAY 2 timer is bypassed. It is up to the user to integrate the blocking
(POWER SWING BLOCK) and tripping (POWER SWING TRIP) FlexLogic operands with other protection functions and out-
put contacts in order to make this element fully operational.
The element can be set to use either lens (mho) or rectangular (quadrilateral) characteristics as illustrated below. When set
to “Mho”, the element applies the right and left blinders as well. If the blinders are not required, their settings should be set
high enough to effectively disable the blinders.

R
TE
OU
ACH
E
DL
FWD RE
ID
M
R
NE
IN
FW
E
GL
DR
AN
CA
LE IT
IM
ANG L EL
R
RE
IT DD
LIM MI
V RC
R
NE
A
IN
H
REV REAC
OUTER LIMIT ANGLE
827843A2.CDR
Figure 5–86: POWER SWING DETECT MHO OPERATING CHARACTERISTICS
842734A1.CDR
Figure 5–87: EFFECTS OF BLINDERS ON THE MHO CHARACTERISTICS

INNER LFT BL
D INNER RGT BL
D
MIDDLE LFT BL
ACH OUT
ACH MID
D MIDDLE RGT
BLD
OUTER LFT BL
D OUTER RGT BL
D
QUAD FWD RE
QUAD FWD RE
FWD REACH
FWD RCA
CH MID
REV REACH
ACH OUT
QUAD REV REA
QUAD REV RE
5 842735A1.CDR
Figure 5–88: POWER SWING DETECT QUADRILATERAL OPERATING CHARACTERISTICS

The FlexLogic output operands for the power swing detect element are described below:
• The POWER SWING OUTER, POWER SWING MIDDLE, POWER SWING INNER, POWER SWING TMR2 PKP, POWER SWING
TMR3 PKP, and POWER SWING TMR4 PKP FlexLogic operands are auxiliary operands that could be used to facilitate
testing and special applications.
• The POWER SWING BLOCK FlexLogic operand shall be used to block selected protection elements such as distance
functions.
• The POWER SWING UN/BLOCK FlexLogic operand shall be used to block those protection elements that are intended to
be blocked under power swings, but subsequently unblocked should a fault occur after the power swing blocking con-
dition has been established.
• The POWER SWING 50DD FlexLogic operand indicates that an adaptive disturbance detector integrated with the ele-
ment has picked up. This operand will trigger on faults occurring during power swing conditions. This includes both
three-phase and single-pole-open conditions.
• The POWER SWING INCOMING FlexLogic operand indicates an unstable power swing with an incoming locus (the locus
enters the inner characteristic).
• The POWER SWING OUTGOING FlexLogic operand indicates an unstable power swing with an outgoing locus (the locus
leaving the outer characteristic). This operand can be used to count unstable swings and take certain action only after
pre-defined number of unstable power swings.
• The POWER SWING TRIP FlexLogic operand is a trip command.
The settings for the power swing detect element are described below:
• POWER SWING FUNCTION: This setting enables and disables the entire power swing detection element. The setting
applies to both power swing blocking and out-of-step tripping functions.
• POWER SWING SOURCE: The source setting identifies the signal source for both blocking and tripping functions.
• POWER SWING SHAPE: This setting selects the shapes (either “Mho” or “Quad”) of the outer, middle and, inner char-
acteristics of the power swing detect element. The operating principle is not affected. The “Mho” characteristics use the
left and right blinders.

• POWER SWING MODE: This setting selects between the two-step and three-step operating modes and applies to
both power swing blocking and out-of-step tripping functions. The three-step mode applies if there is enough space
between the maximum load impedances and distance characteristics of the relay that all three (outer, middle, and
inner) characteristics can be placed between the load and the distance characteristics. Whether the spans between
the outer and middle as well as the middle and inner characteristics are sufficient should be determined by analysis of
the fastest power swings expected in correlation with settings of the power swing timers.
The two-step mode uses only the outer and inner characteristics for both blocking and tripping functions. This leaves
more space in heavily loaded systems to place two power swing characteristics between the distance characteristics
and the maximum load, but allows for only one determination of the impedance trajectory.
• POWER SWING SUPV: A common overcurrent pickup level supervises all three power swing characteristics. The
supervision responds to the positive sequence current.
• POWER SWING FWD REACH: This setting specifies the forward reach of all three mho characteristics and the inner
quadrilateral characteristic. For a simple system consisting of a line and two equivalent sources, this reach should be
higher than the sum of the line and remote source positive-sequence impedances. Detailed transient stability studies
may be needed for complex systems in order to determine this setting. The angle of this reach impedance is specified
by the POWER SWING FWD RCA setting.
• POWER SWING QUAD FWD REACH MID: This setting specifies the forward reach of the middle quadrilateral charac-
teristic. The angle of this reach impedance is specified by the POWER SWING FWD RCA setting. The setting is not used if
the shape setting is “Mho”.
• POWER SWING QUAD FWD REACH OUT: This setting specifies the forward reach of the outer quadrilateral charac-
• POWER SWING FWD RCA: This setting specifies the angle of the forward reach impedance for the mho characteris-
tics, angles of all the blinders, and both forward and reverse reach impedances of the quadrilateral characteristics. 5
• POWER SWING REV REACH: This setting specifies the reverse reach of all three mho characteristics and the inner
quadrilateral characteristic. For a simple system of a line and two equivalent sources, this reach should be higher than
the positive-sequence impedance of the local source. Detailed transient stability studies may be needed for complex
systems to determine this setting. The angle of this reach impedance is specified by the POWER SWING REV RCA setting
for “Mho”, and the POWER SWING FWD RCA setting for “Quad”.
• POWER SWING QUAD REV REACH MID: This setting specifies the reverse reach of the middle quadrilateral charac-
• POWER SWING QUAD REV REACH OUT: This setting specifies the reverse reach of the outer quadrilateral charac-
• POWER SWING REV RCA: This setting specifies the angle of the reverse reach impedance for the mho characteris-
tics. This setting applies to mho shapes only.
• POWER SWING OUTER LIMIT ANGLE: This setting defines the outer power swing characteristic. The convention
depicted in the Power swing detect characteristic diagram should be observed: values greater than 90° result in an
apple-shaped characteristic; values less than 90° result in a lens shaped characteristic. This angle must be selected in
consideration of the maximum expected load. If the maximum load angle is known, the outer limit angle should be
coordinated with a 20° security margin. Detailed studies may be needed for complex systems to determine this setting.
This setting applies to mho shapes only.
• POWER SWING MIDDLE LIMIT ANGLE: This setting defines the middle power swing detect characteristic. It is rele-
vant only for the 3-step mode. A typical value would be close to the average of the outer and inner limit angles. This
setting applies to mho shapes only.
• POWER SWING INNER LIMIT ANGLE: This setting defines the inner power swing detect characteristic. The inner
characteristic is used by the out-of-step tripping function: beyond the inner characteristic out-of-step trip action is defi-
nite (the actual trip may be delayed as per the TRIP MODE setting). Therefore, this angle must be selected in consider-
ation to the power swing angle beyond which the system becomes unstable and cannot recover.

The inner characteristic is also used by the power swing blocking function in the two-step mode. In this case, set this
angle large enough so that the characteristics of the distance elements are safely enclosed by the inner characteristic.
This setting applies to mho shapes only.
• POWER SWING OUTER, MIDDLE, and INNER RGT BLD: These settings specify the resistive reach of the right
blinder. The blinder applies to both “Mho” and “Quad” characteristics. Set these value high if no blinder is required for
the “Mho” characteristic.
• POWER SWING OUTER, MIDDLE, and INNER LFT BLD: These settings specify the resistive reach of the left blinder.
Enter a positive value; the relay automatically uses a negative value. The blinder applies to both “Mho” and “Quad”
characteristics. Set this value high if no blinder is required for the “Mho” characteristic.
• POWER SWING PICKUP DELAY 1: All the coordinating timers are related to each other and should be set to detect
the fastest expected power swing and produce out-of-step tripping in a secure manner. The timers should be set in
consideration to the power swing detect characteristics, mode of power swing detect operation and mode of out-of-
step tripping. This timer defines the interval that the impedance locus must spend between the outer and inner charac-
teristics (two-step operating mode), or between the outer and middle characteristics (three-step operating mode)
before the power swing blocking signal is established. This time delay must be set shorter than the time required for
the impedance locus to travel between the two selected characteristics during the fastest expected power swing. This
setting is relevant for both power swing blocking and out-of-step tripping.
• POWER SWING RESET DELAY 1: This setting defines the dropout delay for the power swing blocking signal. Detec-
tion of a condition requiring a block output sets latch 1 after PICKUP DELAY 1 time. When the impedance locus leaves
the outer characteristic, timer POWER SWING RESET DELAY 1 is started. When the timer times-out the latch is reset. This
setting should be selected to give extra security for the power swing blocking action.
• POWER SWING PICKUP DELAY 2: Controls the out-of-step tripping function in the three-step mode only. This timer
defines the interval the impedance locus must spend between the middle and inner characteristics before the second
5 step of the out-of-step tripping sequence is completed. This time delay must be set shorter than the time required for
the impedance locus to travel between the two characteristics during the fastest expected power swing.
• POWER SWING PICKUP DELAY 3: Controls the out-of-step tripping function only. It defines the interval the imped-
ance locus must spend within the inner characteristic before the last step of the out-of-step tripping sequence is com-
pleted and the element is armed to trip. The actual moment of tripping is controlled by the TRIP MODE setting. This time
delay is provided for extra security before the out-of-step trip action is executed.
• POWER SWING PICKUP DELAY 4: Controls the out-of-step tripping function in “Delayed” trip mode only. This timer
defines the interval the impedance locus must spend outside the inner characteristic but within the outer characteristic
before the element is armed for the delayed trip. The delayed trip occurs when the impedance leaves the outer charac-
teristic. This time delay is provided for extra security and should be set considering the fastest expected power swing.
• POWER SWING SEAL-IN DELAY: The out-of-step trip FlexLogic operand (POWER SWING TRIP) is sealed-in for the
specified period of time. The sealing-in is crucial in the delayed trip mode, as the original trip signal is a very short
pulse occurring when the impedance locus leaves the outer characteristic after the out-of-step sequence is completed.
• POWER SWING TRIP MODE: Selection of the “Early” trip mode results in an instantaneous trip after the last step in
the out-of-step tripping sequence is completed. The early trip mode will stress the circuit breakers as the currents at
that moment are high (the electromotive forces of the two equivalent systems are approximately 180° apart). Selection
of the “Delayed” trip mode results in a trip at the moment when the impedance locus leaves the outer characteristic.
delayed trip mode will relax the operating conditions for the breakers as the currents at that moment are low. The
selection should be made considering the capability of the breakers in the system.
• POWER SWING BLK: This setting specifies the FlexLogic operand used for blocking the out-of-step function only. The
power swing blocking function is operational all the time as long as the element is enabled. The blocking signal resets
the output POWER SWING TRIP operand but does not stop the out-of-step tripping sequence.

SETTINGS
POWER SWING POWER SWING OUTER
SHAPE: LIMIT ANGLE:
POWER SWING FWD POWER SWING MIDDLE
REACH: LIMIT ANGLE:
POWER SWING QUAD POWER SWING INNER
FWD REACH MID: LIMIT ANGLE:
POWER SWING QUAD POWER SWING OUTER
FWD REACH OUT: RGT BLD:
POWER SWING FWD POWER SWING OUTER
RCA: LFT BLD:
POWER SWING REV POWER SWING MIDDLE
SETTING REACH: RGT BLD:
POWER SWING POWER SWING QUAD REV POWER SWING MIDDLE
FUNCTION: REACH MID: LFT BLD:
Enabled = 1 POWER SWING QUAD REV POWER SWING INNER
REACH OUT: RGT BLD:
SETTING POWER SWING REV POWER SWING INNER
RCA: LFT BLD:
POWER SWING SOURCE:
RUN
FLEXLOGIC OPERAND
V_1 OUTER IMPEDANCE
AND POWER SWING OUTER
I_1 REGION
RUN
FLEXLOGIC OPERAND
MIDDLE IMPEDANCE
AND POWER SWING MIDDLE
REGION
RUN
FLEXLOGIC OPERAND
INNER IMPEDANCE
AND POWER SWING INNER
REGION
SETTING
POWER SWING
SUPV:
5
RUN
I_1 > PICKUP

827840A4.CDR
Figure 5–89: POWER SWING DETECT SCHEME LOGIC (1 of 3)
SETTING
POWER SWING FUNCTION:
TIMER
Enabled = 1
0
SETTING 10 cycles
POWER SWING SOURCE: RUN TIMER

FLEXLOGIC OPERAND
0
I_0 | |I_0| - |I_0'|| > K_0
AND
POWER SWING 50DD

4 cycles
OR
I_1 | |I_1| - |I_1'|| > K_1
I_2 | |I_2| - |I_2'|| > K_2
I_0, I_1, I_2 - present values

I_0', I_1', I_2' - half-a-cycle old values
K_0, K_2 - three times the average change over last power cycle
K_1 - four times the average change over last power cycle 842008A2.CDR

POWER SWING OUTER
POWER SWING MIDDLE
POWER SWING INNER
FLEXLOGIC OPERANDS
SETTING SETTINGS
POWER SWING
POWER SWING MODE:
DELAY 1 PICKUP:
POWER SWING
3-step
AND DELAY 1 RESET:
FLEXLOGIC OPERANDS
tPKP
S Q1 POWER SWING BLOCK
tRST
POWER SWING UN/BLOCK
AND L1 S Q5
2-step FLEXLOGIC OPERAND
L5
R POWER SWING 50DD
R
OR
OR
SETTING
POWER SWING FLEXLOGIC OPERAND
DELAY 2 PICKUP:
POWER SWING TMR2 PKP
tPKP
AND S Q2
0
L2
R
3-step
2-step
FLEXLOGIC OPERAND
SETTING POWER SWING TMR3 PKP
POWER SWING
DELAY 3 PICKUP: FLEXLOGIC OPERAND
5
tPKP POWER SWING INCOMING
AND S Q3
0
L3 SETTING
R
POWER SWING TRIP
MODE:
SETTING SETTING
POWER SWING POWER SWING
DELAY 4 PICKUP: Early
SEAL-IN DELAY:
tPKP 0
AND S Q4 FLEXLOGIC OPERAND
0 tRST
L4 AND POWER SWING TRIP
R AND
Delayed
SETTING FLEXLOGIC OPERAND

NOTE: POWER SWING TMR4 PKP
POWER SWING BLK:
L1 AND L4 LATCHES ARE SET DOMINANT
L2, L3 AND L5 LATCHES ARE RESET DOMINANT Off=0
FLEXLOGIC OPERAND
POWER SWING OUTGOING
827841A4.CDR

5.6.6 LOAD ENCROACHMENT
PATH: SETTINGS  GROUPED ELEMENTS  SETTING GROUP 1(6)  LOAD ENCROACHMENT
 LOAD ENCROACHMENT LOAD ENCROACHMENT Range: Disabled, Enabled

LOAD ENCROACHMENT Range: SRC 1, SRC 2, SRC 3, SRC 4
MESSAGE
SOURCE: SRC 1
LOAD ENCROACHMENT Range: 0.000 to 3.000 pu in steps of 0.001
MESSAGE
MIN VOLT: 0.250 pu
LOAD ENCROACHMENT Range: 0.02 to 250.00 ohms in steps of 0.01
MESSAGE
REACH: 1.00 
LOAD ENCROACHMENT Range: 5 to 50° in steps of 1
MESSAGE
ANGLE: 30°
LOAD ENCROACHMENT Range: 0.000 to 65.535 s in steps of 0.001
MESSAGE
PKP DELAY: 0.000 s
LOAD ENCROACHMENT Range: 0.000 to 65.535 s in steps of 0.001
MESSAGE
RST DELAY: 0.000 s
LOAD ENCRMNT BLK: Range: Flexlogic operand
MESSAGE
Off
LOAD ENCROACHMENT Range: Self-reset, Latched, Disabled
MESSAGE
TARGET: Self-reset 5
LOAD ENCROACHMENT Range: Disabled, Enabled
MESSAGE
EVENTS: Disabled
The load encroachment element responds to the positive-sequence voltage and current and applies a characteristic shown
in the figure below.
X
ANGLE
–REACH REACH
R
ANGLE
LOAD ENCROACHMENT
LOAD ENCROACHMENT
OPERATE
OPERATE
827846A1.CDR
Figure 5–92: LOAD ENCROACHMENT CHARACTERISTIC

The element operates if the positive-sequence voltage is above a settable level and asserts its output signal that can be
used to block selected protection elements such as distance or phase overcurrent. The following figure shows an effect of
the load encroachment characteristics used to block the quadrilateral distance element.

837731A1.CDR
Figure 5–93: LOAD ENCROACHMENT APPLIED TO DISTANCE ELEMENT

• LOAD ENCROACHMENT MIN VOLT: This setting specifies the minimum positive-sequence voltage required for oper-
ation of the element. If the voltage is below this threshold a blocking signal will not be asserted by the element. When
selecting this setting one must remember that the D60 measures the phase-to-ground sequence voltages regardless
of the VT connection.
The nominal VT secondary voltage as specified with the SYSTEM SETUP  AC INPUTS  VOLTAGE BANK X5  PHASE
VT SECONDARY setting is the per-unit base for this setting.
5 • LOAD ENCROACHMENT REACH: This setting specifies the resistive reach of the element as shown in the Load
encroachment characteristic diagram. This setting should be entered in secondary ohms and be calculated as the pos-
itive-sequence resistance seen by the relay under maximum load conditions and unity power factor.
• LOAD ENCROACHMENT ANGLE: This setting specifies the size of the blocking region as shown on the Load
encroachment characteristic diagram and applies to the positive-sequence impedance.
SETTING
LOAD ENCROACHMENT
FUNCTION:
Enabled=1 SETTINGS
LOAD ENCROACHMENT
SETTING REACH:
SETTINGS
LOAD ENCROACHMENT
LOAD ENCRMNT BLK:
ANGLE: LOAD ENCROACHMENT
Off=0 RUN PKP DELAY:
AND FLEXLOGIC OPERANDS
LOAD ENCROACHMENT
LOAD ENCHR PKP
RST DELAY:
SETTING SETTING LOAD ENCHR DPO
Load Encroachment t PKP
LOAD ENCROACHMENT LOAD ENCROACHMENT t RST LOAD ENCHR OP
SOURCE: MIN VOLT: Characteristic
Pos Seq Voltage (V_1) V_1 > Pickup
Pos Seq Current (I_1)
827847A3.CDR
Figure 5–94: LOAD ENCROACHMENT SCHEME LOGIC

5.6.7 PHASE CURRENT
a) MAIN MENU
PATH: SETTINGS  GROUPED ELEMENTS  SETTING GROUP 1(6)  PHASE CURRENT
 PHASE CURRENT  PHASE TOC1

See page 5–192.
 
 PHASE TOC2

 PHASE IOC1

 PHASE IOC2

 PHASE
 DIRECTIONAL 1
 PHASE
 DIRECTIONAL 2
b) INVERSE TIME OVERCURRENT CHARACTERISTICS

The inverse time overcurrent curves used by the time overcurrent elements are the IEEE, IEC, GE Type IAC, and I2t stan-
dard curve shapes. This allows for simplified coordination with downstream devices.
If none of these curve shapes is adequate, FlexCurves may be used to customize the inverse time curve characteristics.
The definite time curve is also an option that may be appropriate if only simple protection is required.
5
Table 5–19: OVERCURRENT CURVE TYPES
IEEE IEC GE TYPE IAC OTHER
IEEE Extremely Inverse IEC Curve A (BS142) IAC Extremely Inverse I2t
IEEE Very Inverse IEC Curve B (BS142) IAC Very Inverse FlexCurves A, B, C, and D
IEEE Moderately Inverse IEC Curve C (BS142) IAC Inverse Recloser Curves
IEC Short Inverse IAC Short Inverse Definite Time
A time dial multiplier setting allows selection of a multiple of the base curve shape (where the time dial multiplier = 1) with
the curve shape (CURVE) setting. Unlike the electromechanical time dial equivalent, operate times are directly proportional
to the time multiplier (TD MULTIPLIER) setting value. For example, all times for a multiplier of 10 are 10 times the multiplier 1
or base curve values. Setting the multiplier to zero results in an instantaneous response to all current levels above pickup.
Time overcurrent time calculations are made with an internal energy capacity memory variable. When this variable indi-
cates that the energy capacity has reached 100%, a time overcurrent element will operate. If less than 100% energy capac-
ity is accumulated in this variable and the current falls below the dropout threshold of 97 to 98% of the pickup value, the
variable must be reduced. Two methods of this resetting operation are available: “Instantaneous” and “Timed”. The “Instan-
taneous” selection is intended for applications with other relays, such as most static relays, which set the energy capacity
directly to zero when the current falls below the reset threshold. The “Timed” selection can be used where the relay must
coordinate with electromechanical relays.
IEEE CURVES:
The IEEE time overcurrent curve shapes conform to industry standards and the IEEE C37.112-1996 curve classifications
for extremely, very, and moderately inverse. The IEEE curves are derived from the formulae:
A tr
---------------------------------- + B -----------------------------------
-
I p
T = TDM   ---------------- – 1 , T RESET = TDM  I 2
 --------------- (EQ 5.7)
 I pickup 1 – -
 I pickup 

where: T = operate time (in seconds), TDM = Multiplier setting, I = input current, Ipickup = Pickup Current setting
A, B, p = constants, TRESET = reset time in seconds (assuming energy capacity is 100% and RESET is “Timed”),
tr = characteristic constant
Table 5–20: IEEE INVERSE TIME CURVE CONSTANTS

IEEE CURVE SHAPE A B P TR
IEEE Extremely Inverse 28.2 0.1217 2.0000 29.1
IEEE Very Inverse 19.61 0.491 2.0000 21.6
IEEE Moderately Inverse 0.0515 0.1140 0.02000 4.85
Table 5–21: IEEE CURVE TRIP TIMES (IN SECONDS)

MULTIPLIER CURRENT ( I / Ipickup)
(TDM) 1.5 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0
IEEE EXTREMELY INVERSE
0.5 11.341 4.761 1.823 1.001 0.648 0.464 0.355 0.285 0.237 0.203
1.0 22.682 9.522 3.647 2.002 1.297 0.927 0.709 0.569 0.474 0.407
2.0 45.363 19.043 7.293 4.003 2.593 1.855 1.418 1.139 0.948 0.813
4.0 90.727 38.087 14.587 8.007 5.187 3.710 2.837 2.277 1.897 1.626
6.0 136.090 57.130 21.880 12.010 7.780 5.564 4.255 3.416 2.845 2.439
8.0 181.454 76.174 29.174 16.014 10.374 7.419 5.674 4.555 3.794 3.252
10.0 226.817 95.217 36.467 20.017 12.967 9.274 7.092 5.693 4.742 4.065
IEEE VERY INVERSE
5 0.5
1.0
8.090
16.179
3.514
7.028
1.471
2.942
0.899
1.798
0.654
1.308
0.526
1.051
0.450
0.900
0.401
0.802
0.368
0.736
0.345
0.689
2.0 32.358 14.055 5.885 3.597 2.616 2.103 1.799 1.605 1.472 1.378
4.0 64.716 28.111 11.769 7.193 5.232 4.205 3.598 3.209 2.945 2.756
6.0 97.074 42.166 17.654 10.790 7.849 6.308 5.397 4.814 4.417 4.134
8.0 129.432 56.221 23.538 14.387 10.465 8.410 7.196 6.418 5.889 5.513
10.0 161.790 70.277 29.423 17.983 13.081 10.513 8.995 8.023 7.361 6.891
IEEE MODERATELY INVERSE
0.5 3.220 1.902 1.216 0.973 0.844 0.763 0.706 0.663 0.630 0.603
1.0 6.439 3.803 2.432 1.946 1.688 1.526 1.412 1.327 1.260 1.207
2.0 12.878 7.606 4.864 3.892 3.377 3.051 2.823 2.653 2.521 2.414
4.0 25.756 15.213 9.729 7.783 6.753 6.102 5.647 5.307 5.041 4.827
6.0 38.634 22.819 14.593 11.675 10.130 9.153 8.470 7.960 7.562 7.241
8.0 51.512 30.426 19.458 15.567 13.507 12.204 11.294 10.614 10.083 9.654
10.0 64.390 38.032 24.322 19.458 16.883 15.255 14.117 13.267 12.604 12.068

IEC CURVES
For European applications, the relay offers three standard curves defined in IEC 255-4 and British standard BS142. These
are defined as IEC Curve A, IEC Curve B, and IEC Curve C. The formulae for these curves are:
K tr
--------------------------------------- --------------------------------------
-
T = TDM   I  I pickup  E – 1 , T RESET = TDM  1 –  I  I 2 (EQ 5.8)
pickup 
where: T = operate time (in seconds), TDM = Multiplier setting, I = input current, Ipickup = Pickup Current setting, K, E =
constants, tr = characteristic constant, and TRESET = reset time in seconds (assuming energy capacity is 100%
and RESET is “Timed”)
Table 5–22: IEC (BS) INVERSE TIME CURVE CONSTANTS

IEC (BS) CURVE SHAPE K E TR
IEC Curve A (BS142) 0.140 0.020 9.7
IEC Curve B (BS142) 13.500 1.000 43.2
IEC Curve C (BS142) 80.000 2.000 58.2
IEC Short Inverse 0.050 0.040 0.500
Table 5–23: IEC CURVE TRIP TIMES (IN SECONDS)

(TDM)
1.5 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0
IEC CURVE A
0.05 0.860 0.501 0.315 0.249 0.214 0.192 0.176 0.165 0.156 0.149
0.10
0.20
1.719
3.439
1.003
2.006
0.630
1.260
0.498
0.996
0.428
0.856
0.384
0.767
0.353
0.706
0.330
0.659
0.312
0.623
0.297
0.594
5
0.40 6.878 4.012 2.521 1.992 1.712 1.535 1.411 1.319 1.247 1.188
0.60 10.317 6.017 3.781 2.988 2.568 2.302 2.117 1.978 1.870 1.782
0.80 13.755 8.023 5.042 3.984 3.424 3.070 2.822 2.637 2.493 2.376
1.00 17.194 10.029 6.302 4.980 4.280 3.837 3.528 3.297 3.116 2.971
IEC CURVE B
0.05 1.350 0.675 0.338 0.225 0.169 0.135 0.113 0.096 0.084 0.075
0.10 2.700 1.350 0.675 0.450 0.338 0.270 0.225 0.193 0.169 0.150
0.20 5.400 2.700 1.350 0.900 0.675 0.540 0.450 0.386 0.338 0.300
0.40 10.800 5.400 2.700 1.800 1.350 1.080 0.900 0.771 0.675 0.600
0.60 16.200 8.100 4.050 2.700 2.025 1.620 1.350 1.157 1.013 0.900
0.80 21.600 10.800 5.400 3.600 2.700 2.160 1.800 1.543 1.350 1.200
1.00 27.000 13.500 6.750 4.500 3.375 2.700 2.250 1.929 1.688 1.500
IEC CURVE C
0.05 3.200 1.333 0.500 0.267 0.167 0.114 0.083 0.063 0.050 0.040
0.10 6.400 2.667 1.000 0.533 0.333 0.229 0.167 0.127 0.100 0.081
0.20 12.800 5.333 2.000 1.067 0.667 0.457 0.333 0.254 0.200 0.162
0.40 25.600 10.667 4.000 2.133 1.333 0.914 0.667 0.508 0.400 0.323
0.60 38.400 16.000 6.000 3.200 2.000 1.371 1.000 0.762 0.600 0.485
0.80 51.200 21.333 8.000 4.267 2.667 1.829 1.333 1.016 0.800 0.646
1.00 64.000 26.667 10.000 5.333 3.333 2.286 1.667 1.270 1.000 0.808
IEC SHORT TIME
0.05 0.153 0.089 0.056 0.044 0.038 0.034 0.031 0.029 0.027 0.026
0.10 0.306 0.178 0.111 0.088 0.075 0.067 0.062 0.058 0.054 0.052
0.20 0.612 0.356 0.223 0.175 0.150 0.135 0.124 0.115 0.109 0.104
0.40 1.223 0.711 0.445 0.351 0.301 0.269 0.247 0.231 0.218 0.207
0.60 1.835 1.067 0.668 0.526 0.451 0.404 0.371 0.346 0.327 0.311
0.80 2.446 1.423 0.890 0.702 0.602 0.538 0.494 0.461 0.435 0.415
1.00 3.058 1.778 1.113 0.877 0.752 0.673 0.618 0.576 0.544 0.518

IAC CURVES:
The curves for the General Electric type IAC relay family are derived from the formulae:
 B D E  tr
T = TDM   A + ------------------------------ + -------------------------------------2- + -------------------------------------3- , T RESET = TDM  -------------------------------
- (EQ 5.9)
  I  I pkp  – C   I  I  – C    I  I  – C   2
pkp pkp 1 –  I  I pkp 
where: T = operate time (in seconds), TDM = Multiplier setting, I = Input current, Ipkp = Pickup Current setting, A to E =
constants, tr = characteristic constant, and TRESET = reset time in seconds (assuming energy capacity is 100%
and RESET is “Timed”)
Table 5–24: GE TYPE IAC INVERSE TIME CURVE CONSTANTS

IAC CURVE SHAPE A B C D E TR
IAC Extreme Inverse 0.0040 0.6379 0.6200 1.7872 0.2461 6.008
IAC Very Inverse 0.0900 0.7955 0.1000 –1.2885 7.9586 4.678
IAC Inverse 0.2078 0.8630 0.8000 –0.4180 0.1947 0.990
IAC Short Inverse 0.0428 0.0609 0.6200 –0.0010 0.0221 0.222
Table 5–25: IAC CURVE TRIP TIMES

(TDM)
1.5 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0
IAC EXTREMELY INVERSE
0.5 1.699 0.749 0.303 0.178 0.123 0.093 0.074 0.062 0.053 0.046
5 1.0
2.0
3.398
6.796
1.498
2.997
0.606
1.212
0.356
0.711
0.246
0.491
0.186
0.372
0.149
0.298
0.124
0.248
0.106
0.212
0.093
0.185
4.0 13.591 5.993 2.423 1.422 0.983 0.744 0.595 0.495 0.424 0.370
6.0 20.387 8.990 3.635 2.133 1.474 1.115 0.893 0.743 0.636 0.556
8.0 27.183 11.987 4.846 2.844 1.966 1.487 1.191 0.991 0.848 0.741
10.0 33.979 14.983 6.058 3.555 2.457 1.859 1.488 1.239 1.060 0.926
IAC VERY INVERSE
0.5 1.451 0.656 0.269 0.172 0.133 0.113 0.101 0.093 0.087 0.083
1.0 2.901 1.312 0.537 0.343 0.266 0.227 0.202 0.186 0.174 0.165
2.0 5.802 2.624 1.075 0.687 0.533 0.453 0.405 0.372 0.349 0.331
4.0 11.605 5.248 2.150 1.374 1.065 0.906 0.810 0.745 0.698 0.662
6.0 17.407 7.872 3.225 2.061 1.598 1.359 1.215 1.117 1.046 0.992
8.0 23.209 10.497 4.299 2.747 2.131 1.813 1.620 1.490 1.395 1.323
10.0 29.012 13.121 5.374 3.434 2.663 2.266 2.025 1.862 1.744 1.654
IAC INVERSE
0.5 0.578 0.375 0.266 0.221 0.196 0.180 0.168 0.160 0.154 0.148
1.0 1.155 0.749 0.532 0.443 0.392 0.360 0.337 0.320 0.307 0.297
2.0 2.310 1.499 1.064 0.885 0.784 0.719 0.674 0.640 0.614 0.594
4.0 4.621 2.997 2.128 1.770 1.569 1.439 1.348 1.280 1.229 1.188
6.0 6.931 4.496 3.192 2.656 2.353 2.158 2.022 1.921 1.843 1.781
8.0 9.242 5.995 4.256 3.541 3.138 2.878 2.695 2.561 2.457 2.375
10.0 11.552 7.494 5.320 4.426 3.922 3.597 3.369 3.201 3.072 2.969
IAC SHORT INVERSE
0.5 0.072 0.047 0.035 0.031 0.028 0.027 0.026 0.026 0.025 0.025
1.0 0.143 0.095 0.070 0.061 0.057 0.054 0.052 0.051 0.050 0.049
2.0 0.286 0.190 0.140 0.123 0.114 0.108 0.105 0.102 0.100 0.099
4.0 0.573 0.379 0.279 0.245 0.228 0.217 0.210 0.204 0.200 0.197
6.0 0.859 0.569 0.419 0.368 0.341 0.325 0.314 0.307 0.301 0.296
8.0 1.145 0.759 0.559 0.490 0.455 0.434 0.419 0.409 0.401 0.394
10.0 1.431 0.948 0.699 0.613 0.569 0.542 0.524 0.511 0.501 0.493

I2t CURVES:
The curves for the I2t are derived from the formulae:
100 100
-------------------------- ----------------------------
T = TDM   ---------------
I  2 , T RESET = TDM   I  – 2
- ---------------- (EQ 5.10)
 I pickup   I pickup 
where: T = Operate Time (sec.); TDM = Multiplier Setting; I = Input Current; Ipickup = Pickup Current Setting;
TRESET = Reset Time in sec. (assuming energy capacity is 100% and RESET: Timed)
Table 5–26: I2T CURVE TRIP TIMES

(TDM)
1.5 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0
0.01 0.44 0.25 0.11 0.06 0.04 0.03 0.02 0.02 0.01 0.01
0.10 4.44 2.50 1.11 0.63 0.40 0.28 0.20 0.16 0.12 0.10
1.00 44.44 25.00 11.11 6.25 4.00 2.78 2.04 1.56 1.23 1.00
10.00 444.44 250.00 111.11 62.50 40.00 27.78 20.41 15.63 12.35 10.00
100.00 4444.4 2500.0 1111.1 625.00 400.00 277.78 204.08 156.25 123.46 100.00
600.00 26666.7 15000.0 6666.7 3750.0 2400.0 1666.7 1224.5 937.50 740.74 600.00
FLEXCURVES:
The custom FlexCurves are described in detail in the FlexCurves section of this chapter. The curve shapes for the Flex-
Curves are derived from the formulae:
I
T = TDM  FlexCurve Time at  ----------------
I
when  ----------------  1.00 (EQ 5.11)
5
I pickup I pickup
I I
T RESET = TDM  FlexCurve Time at  ---------------- when  ----------------  0.98 (EQ 5.12)
I pickup I pickup
where: T = Operate Time (sec.), TDM = Multiplier setting

I = Input Current, Ipickup = Pickup Current setting
TRESET = Reset Time in seconds (assuming energy capacity is 100% and RESET: Timed)
DEFINITE TIME CURVE:
The Definite Time curve shape operates as soon as the pickup level is exceeded for a specified period of time. The base
definite time curve delay is in seconds. The curve multiplier of 0.00 to 600.00 makes this delay adjustable from instanta-
neous to 600.00 seconds in steps of 10 ms.
T = TDM in seconds, when I  I pickup (EQ 5.13)
T RESET = TDM in seconds (EQ 5.14)
where: T = Operate Time (sec.), TDM = Multiplier setting

I = Input Current, Ipickup = Pickup Current setting
TRESET = Reset Time in seconds (assuming energy capacity is 100% and RESET: Timed)
RECLOSER CURVES:
The D60 uses the FlexCurve feature to facilitate programming of 41 recloser curves. Please refer to the FlexCurve section
in this chapter for additional details.

c) PHASE TIME OVERCURRENT (ANSI 51P, IEC PTOC)

PATH: SETTINGS  GROUPED ELEMENTS  SETTING GROUP 1(6)  PHASE CURRENT  PHASE TOC1(2))
 PHASE TOC1 PHASE TOC1 Range: Disabled, Enabled

PHASE TOC1 SIGNAL Range: SRC 1, SRC 2, SRC 3, SRC 4
MESSAGE
SOURCE: SRC 1
PHASE TOC1 Range: Phasor, RMS
MESSAGE
INPUT: Phasor
PHASE TOC1 Range: 0.000 to 30.000 pu in steps of 0.001
MESSAGE
PICKUP: 1.000 pu
PHASE TOC1 Range: See Overcurrent Curve Types table
MESSAGE
CURVE: IEEE Mod Inv
PHASE TOC1 Range: 0.00 to 600.00 in steps of 0.01
MESSAGE
TD MULTIPLIER: 1.00
PHASE TOC1 Range: Instantaneous, Timed
MESSAGE
RESET: Instantaneous
PHASE TOC1 VOLTAGE Range: Disabled, Enabled
MESSAGE
RESTRAINT: Disabled
PHASE TOC1 BLOCK A: Range: FlexLogic operand
MESSAGE
Off
5 PHASE TOC1 BLOCK B: Range: FlexLogic operand
MESSAGE
Off
PHASE TOC1 BLOCK C: Range: FlexLogic operand
MESSAGE
Off
PHASE TOC1 Range: Self-reset, Latched, Disabled
MESSAGE
TARGET: Self-reset
PHASE TOC1 Range: Disabled, Enabled
MESSAGE
EVENTS: Disabled
The phase time overcurrent element can provide a desired time-delay operating characteristic versus the applied current or
be used as a simple definite time element. The phase current input quantities may be programmed as fundamental phasor
magnitude or total waveform RMS magnitude as required by the application.
Two methods of resetting operation are available: “Timed” and “Instantaneous” (refer to the Inverse Time overcurrent
curves characteristic sub-section earlier for details on curve setup, trip times, and reset operation). When the element is
blocked, the time accumulator will reset according to the reset characteristic. For example, if the element reset characteris-
tic is set to “Instantaneous” and the element is blocked, the time accumulator will be cleared immediately.
The PHASE TOC1 PICKUP setting can be dynamically reduced by a voltage restraint feature (when enabled). This is accom-
plished via the multipliers (Mvr) corresponding to the phase-phase voltages of the voltage restraint characteristic curve (see
the figure below); the pickup level is calculated as ‘Mvr’ times the PHASE TOC1 PICKUP setting. If the voltage restraint feature
is disabled, the pickup level always remains at the setting value.

Multiplier for Pickup Current

1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0
Phase-Phase Voltage ÷ VT Nominal Phase-phase Voltage
818784A4.CDR
Figure 5–95: PHASE TIME OVERCURRENT VOLTAGE RESTRAINT CHARACTERISTIC
SETTING
PHASE TOC1
FUNCTION:
Enabled=1
SETTING
PHASE TOC1
BLOCK-A :
Off=0
SETTING
PHASE TOC1
BLOCK-B: 5
Off=0
SETTING
SETTING
PHASE TOC1
PHASE TOC1 INPUT:
BLOCK-C:
PHASE TOC1
Off=0 PICKUP:
PHASE TOC1
SETTING CURVE:
PHASE TOC1 PHASE TOC1
SOURCE: TD MULTIPLIER:
IA
PHASE TOC1
IB RESET: FLEXLOGIC OPERAND
IC AND RUN PHASE TOC1 A PKP
IA PICKUP
Seq=ABC Seq=ACB PHASE TOC1 A DPO
MULTIPLY INPUTS
RUN
t PHASE TOC1 A OP
VAB VAC Set
Calculate Multiplier Set Pickup AND RUN PHASE TOC1 B PKP
RUN
Multiplier-Phase A IB PICKUP
Set PHASE TOC1 B DPO
VBC VBA Set Pickup
Calculate Multiplier t PHASE TOC1 B OP
RUN
Multiplier-Phase B
Set AND RUN PHASE TOC1 C PKP
VCA VCB IC PICKUP
Calculate Multiplier Set Pickup PHASE TOC1 C DPO
Multiplier-Phase C
t PHASE TOC1 C OP
SETTING OR PHASE TOC1 PKP
PHASE TOC1 VOLT
RESTRAINT: OR PHASE TOC1 OP
Enabled
AND PHASE TOC1 DPO
827072A5.CDR
Figure 5–96: PHASE TIME OVERCURRENT 1 SCHEME LOGIC

d) PHASE INSTANTANEOUS OVERCURRENT (ANSI 50P, IEC PIOC)

PATH: SETTINGS  GROUPED ELEMENTS  SETTING GROUP 1(6)  PHASE CURRENT  PHASE IOC 1(2)
 PHASE IOC1 PHASE IOC1 Range: Disabled, Enabled

PHASE IOC1 SIGNAL Range: SRC 1, SRC 2, SRC 3, SRC 4
MESSAGE
SOURCE: SRC 1
PHASE IOC1 Range: 0.000 to 30.000 pu in steps of 0.001
MESSAGE
PICKUP: 1.000 pu
PHASE IOC1 PICKUP Range: 0.00 to 600.00 s in steps of 0.01
MESSAGE
DELAY: 0.00 s
PHASE IOC1 RESET Range: 0.00 to 600.00 s in steps of 0.01
MESSAGE
DELAY: 0.00 s
PHASE IOC1 BLOCK A: Range: FlexLogic operand
MESSAGE
Off
PHASE IOC1 BLOCK B: Range: FlexLogic operand
MESSAGE
Off
PHASE IOC1 BLOCK C: Range: FlexLogic operand
MESSAGE
Off
PHASE IOC1 Range: Self-reset, Latched, Disabled
MESSAGE
TARGET: Self-reset
5 PHASE IOC1 Range: Disabled, Enabled
MESSAGE
EVENTS: Disabled
The phase instantaneous overcurrent element may be used as an instantaneous element with no intentional delay or as a
definite time element. The input current is the fundamental phasor magnitude. For timing curves, see the publication Instan-
taneous Overcurrent Element Response to Saturated Waveforms in UR-Series Relays (GET-8400A).
Figure 5–97: PHASE INSTANTANEOUS OVERCURRENT 1 SCHEME LOGIC

e) PHASE DIRECTIONAL OVERCURRENT (ANSI 67P, IEC PDOC/PTOC)

PATH: SETTINGS  GROUPED ELEMENTS  SETTING GROUP 1(6)  PHASE CURRENT  PHASE DIRECTIONAL 1(2)
 PHASE PHASE DIR 1 Range: Disabled, Enabled

 DIRECTIONAL 1 FUNCTION: Disabled
PHASE DIR 1 SIGNAL Range: SRC 1, SRC 2, SRC 3, SRC 4
MESSAGE
SOURCE: SRC 1
PHASE DIR 1 BLOCK: Range: FlexLogic operand
MESSAGE
Off
PHASE DIR 1 Range: 0 to 359° in steps of 1
MESSAGE
ECA: 30
PHASE DIR POL V1 Range: 0.000 to 3.000 pu in steps of 0.001
MESSAGE
THRESHOLD: 0.700 pu
PHASE DIR 1 BLOCK Range: No, Yes
MESSAGE
WHEN V MEM EXP: No
PHASE DIR 1 Range: Self-reset, Latched, Disabled
MESSAGE
TARGET: Self-reset
PHASE DIR 1 Range: Disabled, Enabled
MESSAGE
EVENTS: Disabled
The phase directional elements (one for each of phases A, B, and C) determine the phase current flow direction for steady
state and fault conditions and can be used to control the operation of the phase overcurrent elements via the BLOCK inputs
of these elements. 5
S
UT 0
TP
OU
–90°
VAG (Unfaulted) Fault angle

set at 60° Lag
VPol
VAG(Faulted) IA
ECA
set at 30°
VBC
VBC
VCG VBG +90°
Phasors for Phase A Polarization:
VPol = VBC × (1/_ECA) = polarizing voltage

IA = operating current
ECA = Element Characteristic Angle at 30° 827800A2.CDR
Figure 5–98: PHASE A DIRECTIONAL POLARIZATION

This element is intended to apply a block signal to an overcurrent element to prevent an operation when current is flowing
in a particular direction. The direction of current flow is determined by measuring the phase angle between the current from
the phase CTs and the line-line voltage from the VTs, based on the 90° or quadrature connection. If there is a requirement
to supervise overcurrent elements for flows in opposite directions, such as can happen through a bus-tie breaker, two
phase directional elements should be programmed with opposite element characteristic angle (ECA) settings.

To increase security for three phase faults very close to the VTs used to measure the polarizing voltage, a voltage memory
feature is incorporated. This feature stores the polarizing voltage the moment before the voltage collapses, and uses it to
determine direction. The voltage memory remains valid for one second after the voltage has collapsed.
The main component of the phase directional element is the phase angle comparator with two inputs: the operating signal
(phase current) and the polarizing signal (the line voltage, shifted in the leading direction by the characteristic angle, ECA).
The following table shows the operating and polarizing signals used for phase directional control:
PHASE OPERATING POLARIZING SIGNAL Vpol
SIGNAL
ABC PHASE SEQUENCE ACB PHASE SEQUENCE
A angle of IA angle of VBC  (1ECA) angle of VCB  (1ECA)
B angle of IB angle of VCA  (1ECA) angle of VAC  1ECA)
C angle of IC angle of VAB  (1ECA) angle of VBA  (1ECA)
MODE OF OPERATION:
• When the function is “Disabled”, or the operating current is below 5%  CT nominal, the element output is “0”.
• When the function is “Enabled”, the operating current is above 5%  CT nominal, and the polarizing voltage is above
the PRODUCT SETUP  DISPLAY PROPERTIES  VOLTAGE CUT-OFF LEVEL value, the element output is dependent on
the phase angle between the operating and polarizing signals:
– The element output is logic “0” when the operating current is within polarizing voltage ±90°.
– For all other angles, the element output is logic “1”.
• Once the voltage memory has expired, the phase overcurrent elements under directional control can be set to block or
trip on overcurrent as follows:
5 – When BLOCK WHEN V MEM EXP is set to “Yes”, the directional element will block the operation of any phase
overcurrent element under directional control when voltage memory expires.
– When BLOCK WHEN V MEM EXP is set to “No”, the directional element allows tripping of phase overcurrent elements
under directional control when voltage memory expires.
In all cases, directional blocking will be permitted to resume when the polarizing voltage becomes greater than the ‘polariz-
ing voltage threshold’.
SETTINGS:
• PHASE DIR 1 SIGNAL SOURCE: This setting is used to select the source for the operating and polarizing signals.
The operating current for the phase directional element is the phase current for the selected current source. The polar-
izing voltage is the line voltage from the phase VTs, based on the 90° or ‘quadrature’ connection and shifted in the
leading direction by the element characteristic angle (ECA).
• PHASE DIR 1 ECA: This setting is used to select the element characteristic angle, i.e. the angle by which the polariz-
ing voltage is shifted in the leading direction to achieve dependable operation. In the design of the UR-series elements,
a block is applied to an element by asserting logic 1 at the blocking input. This element should be programmed via the
ECA setting so that the output is logic 1 for current in the non-tripping direction.
• PHASE DIR 1 POL V THRESHOLD: This setting is used to establish the minimum level of voltage for which the phase
angle measurement is reliable. The setting is based on VT accuracy. The default value is “0.700 pu”.
• PHASE DIR 1 BLOCK WHEN V MEM EXP: This setting is used to select the required operation upon expiration of
voltage memory. When set to "Yes", the directional element blocks the operation of any phase overcurrent element
under directional control, when voltage memory expires; when set to "No", the directional element allows tripping of
phase overcurrent elements under directional control.
The phase directional element responds to the forward load current. In the case of a following reverse fault, the ele-
ment needs some time – in the order of 8 ms – to establish a blocking signal. Some protection elements such as
NOTE
instantaneous overcurrent may respond to reverse faults before the blocking signal is established. Therefore, a
coordination time of at least 10 ms must be added to all the instantaneous protection elements under the supervi-
sion of the phase directional element. If current reversal is of a concern, a longer delay – in the order of 20 ms –
may be needed.

SETTING
PHASE DIR 1
FUNCTION:
Enabled=1
SETTING
AND
PHASE DIR 1
BLOCK:
Off=0
SETTING
SETTING PHASE DIR 1 ECA:
PHASE DIR 1 SOURCE: I 0.05 pu AND RUN 0

IA Vpol
1 FLEXLOGIC OPERAND
Seq=ABC Seq=ACB I OR PH DIR1 BLK
SETTING
VBC VCB
PHASE DIR 1 POL V
THRESHOLD: FLEXLOGIC OPERAND
OR PH DIR1 BLK A
-Use V when V Min
-Use V memory when
V < Min MEMORY TIMER
1 cycle
V MINIMUM
1 sec
AND
SETTING USE ACTUAL VOLTAGE
PHASE DIR 1 BLOCK OC

WHEN V MEM EXP:
USE MEMORIZED VOLTAGE
No
Yes
FLEXLOGIC OPERAND
PHASE B LOGIC SIMILAR TO PHASE A
5
PH DIR1 BLK B
FLEXLOGIC OPERAND
PHASE C LOGIC SIMILAR TO PHASE A PH DIR1 BLK C
827078A7.CDR
Figure 5–99: PHASE DIRECTIONAL SCHEME LOGIC
5.6.8 NEUTRAL CURRENT
a) MAIN MENU
PATH: SETTINGS  GROUPED ELEMENTS  SETTING GROUP 1(6)  NEUTRAL CURRENT
 NEUTRAL CURRENT  NEUTRAL TOC1

See page 5–198.
 
 NEUTRAL TOC2

 NEUTRAL IOC1

 NEUTRAL IOC2

 NEUTRAL
 DIRECTIONAL 1
 NEUTRAL
 DIRECTIONAL 2

b) NEUTRAL TIME OVERCURRENT (ANSI 51N, IEC PTOC)

PATH: SETTINGS  GROUPED ELEMENTS  SETTING GROUP 1(6)  NEUTRAL CURRENT  NEUTRAL TOC1(2)
 NEUTRAL TOC1 NEUTRAL TOC1 Range: Disabled, Enabled

NEUTRAL TOC1 SIGNAL Range: SRC 1, SRC 2, SRC 3, SRC 4
MESSAGE
SOURCE: SRC 1
NEUTRAL TOC1 Range: Phasor, RMS
MESSAGE
INPUT: Phasor
NEUTRAL TOC1 Range: 0.000 to 30.000 pu in steps of 0.001
MESSAGE
PICKUP: 1.000 pu
NEUTRAL TOC1 Range: See OVERCURRENT CURVE TYPES table
MESSAGE
CURVE: IEEE Mod Inv
NEUTRAL TOC1 Range: 0.00 to 600.00 in steps of 0.01
MESSAGE
TD MULTIPLIER: 1.00
NEUTRAL TOC1 Range: Instantaneous, Timed
MESSAGE
NEUTRAL TOC1 BLOCK: Range: FlexLogic operand
MESSAGE
Off
NEUTRAL TOC1 Range: Self-reset, Latched, Disabled
MESSAGE
TARGET: Self-reset
5 NEUTRAL TOC1 Range: Disabled, Enabled
MESSAGE
EVENTS: Disabled
The neutral time overcurrent element can provide a desired time-delay operating characteristic versus the applied current
or be used as a simple definite time element. The neutral current input value is a quantity calculated as 3Io from the phase
currents and may be programmed as fundamental phasor magnitude or total waveform RMS magnitude as required by the
application.
Two methods of resetting operation are available: “Timed” and “Instantaneous” (refer to the Inverse time overcurrent curve
characteristics section for details on curve setup, trip times and reset operation). When the element is blocked, the time
accumulator will reset according to the reset characteristic. For example, if the element reset characteristic is set to “Instan-
taneous” and the element is blocked, the time accumulator will be cleared immediately.
Figure 5–100: NEUTRAL TIME OVERCURRENT 1 SCHEME LOGIC

c) NEUTRAL INSTANTANEOUS OVERCURRENT (ANSI 50N, IEC PIOC)

PATH: SETTINGS  GROUPED ELEMENTS  SETTING GROUP 1(6)  NEUTRAL CURRENT  NEUTRAL IOC1(2)
 NEUTRAL IOC1 NEUTRAL IOC1 Range: Disabled, Enabled

NEUTRAL IOC1 SIGNAL Range: SRC 1, SRC 2, SRC 3, SRC 4
MESSAGE
SOURCE: SRC 1
NEUTRAL IOC1 Range: 0.000 to 30.000 pu in steps of 0.001
MESSAGE
PICKUP: 1.000 pu
NEUTRAL IOC1 PICKUP Range: 0.00 to 600.00 s in steps of 0.01
MESSAGE
DELAY: 0.00 s
NEUTRAL IOC1 RESET Range: 0.00 to 600.00 s in steps of 0.01
MESSAGE
DELAY: 0.00 s
NEUTRAL IOC1 BLOCK: Range: FlexLogic operand
MESSAGE
Off
NEUTRAL IOC1 Range: Self-reset, Latched, Disabled
MESSAGE
TARGET: Self-reset
NEUTRAL IOC1 Range: Disabled, Enabled
MESSAGE
EVENTS: Disabled
The neutral instantaneous overcurrent element may be used as an instantaneous function with no intentional delay or as a
definite time function. The element essentially responds to the magnitude of a neutral current fundamental frequency pha-
sor calculated from the phase currents. A positive-sequence restraint is applied for better performance. A small portion 5
(6.25%) of the positive-sequence current magnitude is subtracted from the zero-sequence current magnitude when forming
the operating quantity of the element as follows:
I op = 3   I_0 – K  I_1  where K = 1  16 (EQ 5.15)
The positive-sequence restraint allows for more sensitive settings by counterbalancing spurious zero-sequence currents
resulting from:
• System unbalances under heavy load conditions
• Transformation errors of current transformers (CTs) during double-line and three-phase faults.
• Switch-off transients during double-line and three-phase faults.
The positive-sequence restraint must be considered when testing for pickup accuracy and response time (multiple of
pickup). The operating quantity depends on how test currents are injected into the relay (single-phase injection:
I op = 0.9375  I injected ; three-phase pure zero-sequence injection: I op = 3  I injected ).
Figure 5–101: NEUTRAL IOC1 SCHEME LOGIC

d) NEUTRAL DIRECTIONAL OVERCURRENT (ANSI 67N, IEC PDEF/PTOC)

PATH: SETTINGS  GROUPED ELEMENTS  SETTING GROUP 1(6)  NEUTRAL CURRENT  NEUTRAL DIRECTIONAL OC1(2)
 NEUTRAL NEUTRAL DIR OC1 Range: Disabled, Enabled

 DIRECTIONAL OC1 FUNCTION: Disabled
NEUTRAL DIR OC1 Range: SRC 1, SRC 2, SRC 3, SRC 4
MESSAGE
SOURCE: SRC 1
NEUTRAL DIR OC1 Range: Voltage, Current, Dual, Dual-V, Dual-I
MESSAGE
POLARIZING: Voltage
NEUTRAL DIR OC1 POL Range: Calculated V0, Measured VX
MESSAGE
VOLT: Calculated V0
NEUTRAL DIR OC1 OP Range: Calculated 3I0, Measured IG
MESSAGE
CURR: Calculated 3I0
NEUTRAL DIR OC1 POS- Range: 0.000 to 0.500 in steps of 0.001
MESSAGE
SEQ RESTRAINT: 0.063
NEUTRAL DIR OC1 Range: 0.00 to 250.00  in steps of 0.01
MESSAGE
OFFSET: 0.00 
NEUTRAL DIR OC1 FWD Range: –90 to 90° in steps of 1
MESSAGE
ECA: 75° Lag
NEUTRAL DIR OC1 FWD Range: 40 to 90° in steps of 1
MESSAGE
LIMIT ANGLE: 90°
5 NEUTRAL DIR OC1 FWD Range: 0.006 to 30.000 pu in steps of 0.001
MESSAGE
PICKUP: 0.050 pu
NEUTRAL DIR OC1 REV Range: 40 to 90° in steps of 1
MESSAGE
LIMIT ANGLE: 90°
NEUTRAL DIR OC1 REV Range: 0.006 to 30.000 pu in steps of 0.001
MESSAGE
PICKUP: 0.050 pu
NEUTRAL DIR OC1 BLK: Range: FlexLogic operand
MESSAGE
Off
NEUTRAL DIR OC1 Range: Self-reset, Latched, Disabled
MESSAGE
TARGET: Self-reset
NEUTRAL DIR OC1 Range: Disabled, Enabled
MESSAGE
EVENTS: Disabled
The neutral directional overcurrent element provides both forward and reverse fault direction indications the NEUTRAL DIR
OC1 FWD and NEUTRAL DIR OC1 REV operands, respectively. The output operand is asserted if the magnitude of the oper-
ating current is above a pickup level (overcurrent unit) and the fault direction is seen as forward or reverse, respectively
(directional unit).
The overcurrent unit responds to the magnitude of a fundamental frequency phasor of the either the neutral current calcu-
lated from the phase currents or the ground current. There are separate pickup settings for the forward-looking and
reverse-looking functions. If set to use the calculated 3I_0, the element applies a positive-sequence restraint for better per-
formance: a small user-programmable portion of the positive-sequence current magnitude is subtracted from the zero-
sequence current magnitude when forming the operating quantity.
I op = 3   I_0 – K  I_1  (EQ 5.16)
The positive-sequence restraint allows for more sensitive settings by counterbalancing spurious zero-sequence currents
resulting from:
• System unbalances under heavy load conditions.

• Transformation errors of current transformers (CTs) during double-line and three-phase faults.
• Switch-off transients during double-line and three-phase faults.
pickup). The operating quantity depends on the way the test currents are injected into the relay (single-phase injection:
Iop = (1 – K)  Iinjected ; three-phase pure zero-sequence injection: Iop = 3  Iinjected).
The positive-sequence restraint is removed for low currents. If the positive-sequence current is below 0.8 pu, the restraint is
removed by changing the constant K to zero. This facilitates better response to high-resistance faults when the unbalance
is very small and there is no danger of excessive CT errors as the current is low.
The directional unit uses the zero-sequence current (I_0) or ground current (IG) for fault direction discrimination and may
be programmed to use either zero-sequence voltage (“Calculated V0” or “Measured VX”), ground current (IG), or both for
polarizing. The zero-sequence current (I_0) must be greater than the PRODUCT SETUP  DISPLAY PROPERTIES  CUR-
RENT CUT-OFF LEVEL setting value and IG must be greater than 0.05 pu to be validated as the operating quantity for direc-
tional current. The following tables define the neutral directional overcurrent element.
Table 5–27: QUANTITIES FOR "CALCULATED 3I0" CONFIGURATION

DIRECTIONAL UNIT
OVERCURRENT UNIT
POLARIZING MODE DIRECTION COMPARED PHASORS
Forward –V_0 + Z_offset  I_0 I_0  1ECA
Voltage
Reverse –V_0 + Z_offset  I_0 –I_0  1ECA
Forward IG I_0
Current
Reverse IG –I_0
–V_0 + Z_offset  I_0 I_0  1ECA Iop = 3  (|I_0| – K  |I_1|) if |I1| > 0.8 pu
Forward
IG
or
I_0
Iop = 3  (|I_0|) if |I1|  0.8 pu
5
Dual, Dual-V, Dual-I
–V_0 + Z_offset  I_0 –I_0  1ECA
Reverse or
IG –I_0
Table 5–28: QUANTITIES FOR "MEASURED IG" CONFIGURATION

DIRECTIONAL UNIT
OVERCURRENT UNIT
POLARIZING MODE DIRECTION COMPARED PHASORS
Forward –V_0 + Z_offset  IG/3 IG  1ECA
Voltage Iop = |IG|
Reverse –V_0 + Z_offset  IG/3 –IG  1ECA
1
where: V_0 = ---  VAG + VBG + VCG  = zero sequence voltage ,
3
1 1
I_0 = --- IN = ---  IA + IB + IC  = zero sequence current ,
3 3
ECA = element characteristic angle and IG = ground current
When NEUTRAL DIR OC1 POL VOLT is set to “Measured VX”, one-third of this voltage is used in place of V_0. The following
figure explains the usage of the voltage polarized directional unit of the element.
The figure below shows the voltage-polarized phase angle comparator characteristics for a phase A to ground fault, with:
• ECA = 90° (element characteristic angle = centerline of operating characteristic)
• FWD LA = 80° (forward limit angle = the ± angular limit with the ECA for operation)
• REV LA = 80° (reverse limit angle = the ± angular limit with the ECA for operation)
The element incorporates a current reversal logic: if the reverse direction is indicated for at least 1.25 of a power system
cycle, the prospective forward indication is delayed by 1.5 of a power system cycle. The element is designed to emulate an
electromechanical directional device. Larger operating and polarizing signals results in faster directional discrimination
bringing more security to the element operation.

The forward-looking function is designed to be more secure as compared to the reverse-looking function, and therefore,
should be used for the tripping direction. The reverse-looking function is designed to be faster as compared to the forward-
looking function and should be used for the blocking direction. This allows for better protection coordination.
The above bias should be taken into account when using the neutral directional overcurrent element to directionalize other
protection elements.
REV LA FWD LA
line –3V_0 line line
VAG
(reference)
REV Operating FWD Operating

Region Region
LA
LA
3I_0 line
ECA
ECA line
–ECA line
–3I_0 line LA
VCG LA
5 VBG
FWD LA
REV LA line
3V_0 line
line 827805A1.CDR
Figure 5–102: NEUTRAL DIRECTIONAL VOLTAGE-POLARIZED CHARACTERISTICS

• NEUTRAL DIR OC1 POLARIZING: This setting selects the polarizing mode for the directional unit.
– If “Voltage” polarizing is selected, the element uses the zero-sequence voltage angle for polarization. The user
can use either the zero-sequence voltage V_0 calculated from the phase voltages, or the zero-sequence voltage
supplied externally as the auxiliary voltage V_X, both from the NEUTRAL DIR OC1 SOURCE.
The calculated V_0 can be used as polarizing voltage only if the voltage transformers are connected in Wye. The
auxiliary voltage can be used as the polarizing voltage provided SYSTEM SETUP  AC INPUTS  VOLTAGE BANK
 AUXILIARY VT CONNECTION is set to “Vn” and the auxiliary voltage is connected to a zero-sequence voltage
source (such as broken delta connected secondary of VTs).
The zero-sequence (V_0) or auxiliary voltage (V_X), accordingly, must be greater than the VOLTAGE CUTOFF
LEVEL setting specified in the PRODUCT SETUP  DISPLAY PROPERTIES menu to be validated for use as a polariz-
ing signal. If the polarizing signal is invalid, neither forward nor reverse indication is given.
– If “Current” polarizing is selected, the element uses the ground current angle connected externally and configured
under NEUTRAL OC1 SOURCE for polarization. The ground CT must be connected between the ground and neutral
point of an adequate local source of ground current. The ground current must be greater than 0.05 pu to be vali-
dated as a polarizing signal. If the polarizing signal is not valid, neither forward nor reverse indication is given. In
addition, the zero-sequence current (I_0) must be greater than the PRODUCT SETUP  DISPLAY PROPERTIES 
CURRENT CUT-OFF LEVEL setting value.
For a choice of current polarizing, it is recommended that the polarizing signal be analyzed to ensure that a known
direction is maintained irrespective of the fault location. For example, if using an autotransformer neutral current
as a polarizing source, it should be ensured that a reversal of the ground current does not occur for a high-side
fault. The low-side system impedance should be assumed minimal when checking for this condition. A similar sit-
uation arises for a wye/delta/wye transformer, where current in one transformer winding neutral may reverse when
faults on both sides of the transformer are considered.

– If “Dual” polarizing is selected, the element performs both directional comparisons as described above. A given
direction is confirmed if either voltage or current comparators indicate so. If a conflicting (simultaneous forward
and reverse) indication occurs, the forward direction overrides the reverse direction.
• NEUTRAL DIR OC1 POL VOLT: Selects the polarizing voltage used by the directional unit when "Voltage," "Dual,"
"Dual-V," or "Dual-I" polarizing mode is set. The polarizing voltage can be programmed to be either the zero-sequence
voltage calculated from the phase voltages ("Calculated V0") or supplied externally as an auxiliary voltage ("Measured
VX").
• NEUTRAL DIR OC1 OP CURR: This setting indicates whether the 3I_0 current calculated from the phase currents, or
the ground current shall be used by this protection. This setting acts as a switch between the neutral and ground
modes of operation (67N and 67G). If set to “Calculated 3I0” the element uses the phase currents and applies the pos-
itive-sequence restraint; if set to “Measured IG” the element uses ground current supplied to the ground CT of the CT
bank configured as NEUTRAL DIR OC1 SOURCE. If this setting is “Measured IG”, then the NEUTRAL DIR OC1 POLARIZING
setting must be “Voltage”, as it is not possible to use the ground current as an operating and polarizing signal simulta-
neously. IG current has to be above 0.05 ps to be used as operate quantity.
• NEUTRAL DIR OC1 POS-SEQ RESTRAINT: This setting controls the amount of the positive-sequence restraint. Set
to 0.063 for backward compatibility with firmware revision 3.40 and older. Set to zero to remove the restraint. Set
higher if large system unbalances or poor CT performance are expected.
• NEUTRAL DIR OC1 OFFSET: This setting specifies the offset impedance used by this protection. The primary appli-
cation for the offset impedance is to guarantee correct identification of fault direction on series compensated lines. In
regular applications, the offset impedance ensures proper operation even if the zero-sequence voltage at the relaying
point is very small. If this is the intent, the offset impedance shall not be larger than the zero-sequence impedance of
the protected circuit. Practically, it shall be several times smaller. The offset impedance shall be entered in secondary
ohms.
See chapter 8 for additional details and chapter 9 for information on how to calculate this setting
5
• NEUTRAL DIR OC1 FWD ECA: This setting defines the characteristic angle (ECA) for the forward direction in the
"Voltage" polarizing mode. The "Current" polarizing mode uses a fixed ECA of 0°. The ECA in the reverse direction is
the angle set for the forward direction shifted by 180°.
• NEUTRAL DIR OC1 FWD LIMIT ANGLE: This setting defines a symmetrical (in both directions from the ECA) limit
angle for the forward direction.
• NEUTRAL DIR OC1 FWD PICKUP: This setting defines the pickup level for the overcurrent unit of the element in the
forward direction. When selecting this setting it must be kept in mind that the design uses a ‘positive-sequence
restraint’ technique for the “Calculated 3I0” mode of operation.
• NEUTRAL DIR OC1 REV LIMIT ANGLE: This setting defines a symmetrical (in both directions from the ECA) limit
angle for the reverse direction.
• NEUTRAL DIR OC1 REV PICKUP: This setting defines the pickup level for the overcurrent unit of the element in the
reverse direction. When selecting this setting it must be kept in mind that the design uses a positive-sequence restraint
technique for the “Calculated 3I0” mode of operation.

Figure 5–103: NEUTRAL DIRECTIONAL OVERCURRENT LOGIC

5.6.9 WATTMETRIC GROUND FAULT
a) WATTMETRIC ZERO-SEQUENCE DIRECTIONAL (ANSI 32N, IEC PSDE)

PATH: SETTINGS  GROUPED ELEMENTS  SETTING GROUP 1(6)  WATTMETRIC...  WATTMETRIC GROUND FAULT 1()
 WATTMETRIC WATTMETRIC GND FLT 1 Range: Disabled, Enabled

 GROUND FAULT 1 FUNCTION: Disabled
WATTMETRIC GND FLT 1 Range: SRC 1, SRC 2, SRC 3, SRC 4
MESSAGE
SOURCE: SRC 1
WATTMETRIC GND FLT 1 Range: Calculated VN, Measured VX
MESSAGE
VOLT: Calculated VN
WATTMETRIC GND FLT 1 Range: 0.02 to 3.00 pu in steps of 0.01
MESSAGE
OV PKP: 0.20 pu
WATTMETRIC GND FLT 1 Range: Calculated IN, Measured IG
MESSAGE
CURR: Calculated IN
MESSAGE
OC PKP: 0.060 pu
WATTMETRIC GND FLT 1 Range: 0.00 to 600.00 s in steps of 0.01
MESSAGE
OC PKP DEL: 0.20 s
MESSAGE
PWR PKP: 0.100 pu
MESSAGE
5
REF PWR: 0.500 pu
WATTMETRIC GND FLT 1 Range: 0 to 360° Lag in steps of 1
MESSAGE
ECA: 0° Lag
MESSAGE
PWR PKP DEL: 0.20 s
WATTMETRIC GND FLT 1 Range: Definite Time, Inverse, FlexCurves A through D
MESSAGE
CURVE: Definite Time
MESSAGE
MULTIPLIER: 1.00 s
WATT GND FLT 1 BLK: Range: FlexLogic operand
MESSAGE
Off
WATTMETRIC GND FLT 1 Range: Self-reset, Latched, Disabled
MESSAGE
TARGET: Self-reset
WATTMETRIC GND FLT 1 Range: Disabled, Enabled
MESSAGE
EVENTS: Disabled
The wattmetric zero-sequence directional element responds to power derived from zero-sequence voltage and current in a
direction specified by the element characteristic angle. The angle can be set within all four quadrants and the power can be
active or reactive. Therefore, the element may be used to sense either forward or reverse ground faults in either inductive,
capacitive or resistive networks. The inverse time characteristic allows time coordination of elements across the network.
Typical applications include ground fault protection in solidly grounded transmission networks, grounded/ungrounded/resis-
tor-grounded/resonant-grounded distribution networks, or for directionalizing other non-directional ground elements.
• WATTMETRIC GND FLT 1 VOLT: The element uses neutral voltage (that is, three times the zero-sequence voltage).
This setting allows selecting between the internally calculated neutral voltage, or externally supplied voltage (broken
delta VT connected to the auxiliary channel bank of the relay). When the latter selection is made, the auxiliary channel
must be identified by the user as a neutral voltage under the VT bank settings. This element operates when the auxil-
iary voltage is configured as neutral.

• WATTMETRIC GND FLT 1 OV PKP: This setting specifies the minimum zero sequence voltage supervising the direc-
tional power measurement. This threshold should be higher than possible unbalance during normal operation of the
system. Typically, this setting would be selected at 0.1 to 0.2 pu for the ungrounded or resonant grounded systems,
and at 0.05 to 0.1 pu for solidly or resistor-grounded systems. When using externally supplied voltage via the auxiliary
voltage channel, 1 pu is the nominal voltage of this channel as per VT bank settings. When using internally calculated
neutral voltage, 1 pu is the nominal phase to ground voltage as per the VT bank settings.
• WATTMETRIC GND FLT 1 CURR: The element responds to the neutral current (that is, three times zero-sequence
current), either calculated internally from the phase currents or supplied externally via the ground CT input from more
accurate sources such as the core balanced CT. This setting allows selecting the source of the operating current.
• WATTMETRIC GND FLT 1 OC PKP: This setting specifies the current supervision level for the measurement of the
zero-sequence power.
• WATTMETRIC GND FLT 1 OC PKP DEL: This setting specifies delay for the overcurrent portion of this element. The
delay applies to the WATTMETRIC 1 PKP operand driven from the overcurrent condition.
• WATTMETRIC GND FLT 1 PWR PKP: This setting specifies the operating point of the element. A value of 1 pu is a
product of the 1 pu voltage as specified for the overvoltage condition of this element, and 1 pu current as specified for
the overcurrent condition of this element.
• WATTMETRIC GND FLT 1 REF PWR: This setting is used to calculate the inverse time characteristic delay (defined
by Sref in the following equations). A value of 1 pu represents the product of a 1 pu voltage (as specified in the overvolt-
age condition for this element) and a 1 pu current (as specified in the overcurrent condition for this element.
• WATTMETRIC GND FLT 1 ECA: This setting adjusts the maximum torque angle of the element. The operating power
is calculated as:
S_op = Re  V n  I n  1 ECA   (EQ 5.17)
5 where * indicates complex conjugate. By varying the element characteristic angle (ECA), the element can be made to
respond to forward or reverse direction in inductive, resistive, or capacitive networks as shown in the Wattmetric char-
acteristic angle response diagram.
• WATTMETRIC GND FLT 1 PWR PKP DEL: This setting defines a definite time delay before the inverse time charac-
teristic is activated. If the curve selection is set as “Definite Time”, the element would operate after this security time
delay. If the curve selection is “Inverse” or one of the FlexCurves, the element uses both the definite and inverse time
timers simultaneously. The definite time timer, specified by this setting, is used and when expires it releases the
inverse time timer for operation (torque control).
• WATTMETRIC GND FLT 1 CURVE: This setting allows choosing one of three methods to delay operate signal once all
conditions are met to discriminate fault direction.
The “Definite Time” selection allows for a fixed time delay defined by the WATTMETRIC GND FLT 1 PWR PKP DEL setting.
The “Inverse” selection allows for inverse time characteristics delay defined by the following formula:
S ref
t = m  ---------- (EQ 5.18)
S op
where m is a multiplier defined by the multiplier setting, Sref is the multiplier setting, and Sop is the operating power at
the time. This timer starts after the definite time timer expires.
The four FlexCurves allow for custom user-programmable time characteristics. When working with FlexCurves, the
element uses the operate to pickup ratio, and the multiplier setting is not applied:
S op
t = FlexCurve  ---------- (EQ 5.19)
 S ref
Again, the FlexCurve timer starts after the definite time timer expires.

FORWARD FAULT REVERSE FAULT
ECA = 180 to 270° ECA = 0 to 90°
INDUCTIVE NETWORK
Vn Vn
In In
RESISTIVE NETWORK
ECA = 180° ECA = 0°
Vn Vn
In In
In In
CAPACITIIVE NETWORK
5
Vn Vn
ECA = 90 to 180° ECA = 270 to 360°
837804A1.CDR
Figure 5–104: WATTMETRIC CHARACTERISTIC ANGLE RESPONSE

• WATTMETRIC GND FLT 1 MULTIPLIER: This setting is applicable if WATTMETRIC GND FLT 1 CURVE above is selected
to Inverse and defines the multiplier factor for the inverse time delay.
SETTINGS SETTINGS
WATTMETRIC GND FLT 1 WATTMETRIC GND FLT 1
SOURCE: PWR PICKUP:
CURRENT: SETTING SETTINGS
OC PICKUP:
Calculated: Measured: WATTMETRIC GND FLT 1 WATTMETRIC GND FLT 1
WATTMETRIC GND FLT 1
Neutral, In Ground, Ig ECA: OV PICKUP: CURVE:
SETTING
VOLTAGE: S = V*conj (I*exp(-j*ECA)) SOP > PWR PICKUP WATTMETRIC GND FLT 1 REF PWR:
Calculated: Measured: 1 PWR PKP DEL:
Neutral, Vn Auxiliary, Vx MULTIPLIER:
VMAG > OV PICKUP
AND
tPKP RUN
0 FLEXLOGIC OPERAND
IMAG > OC PICKUP SREF
SETTINGS t = m× WATTMETRIC 1 OP
SOP
WATTMETRIC GND FLT
AND
SETTING
1 FUNCTION:
Enabled = 1
OC PKP DEL:
AND
WATT GND FLT 1 BLK:

FLEXLOGIC OPERAND
Off = 0
tPKP WATTMETRIC 1 PKP
0
837033A4.CDR
Figure 5–105: WATTMETRIC ZERO-SEQUENCE DIRECTIONAL LOGIC

5.6.10 GROUND CURRENT
a) GROUND TIME OVERCURRENT (ANSI 51G, IEC PTOC)

PATH: SETTINGS  GROUPED ELEMENTS  SETTING GROUP 1(6)  GROUND CURRENT  GROUND TOC1(2)
 GROUND TOC1 GROUND TOC1 Range: Disabled, Enabled

GROUND TOC1 SIGNAL Range: SRC 1, SRC 2, SRC 3, SRC 4
MESSAGE
SOURCE: SRC 1
GROUND TOC1 Range: Phasor, RMS
MESSAGE
INPUT: Phasor
GROUND TOC1 Range: 0.000 to 30.000 pu in steps of 0.001
MESSAGE
PICKUP: 1.000 pu
GROUND TOC1 Range: see the Overcurrent Curve Types table
MESSAGE
CURVE: IEEE Mod Inv
GROUND TOC1 Range: 0.00 to 600.00 in steps of 0.01
MESSAGE
TD MULTIPLIER: 1.00
GROUND TOC1 Range: Instantaneous, Timed
MESSAGE
GROUND TOC1 BLOCK: Range: FlexLogic operand
MESSAGE
Off
5 MESSAGE
GROUND TOC1
TARGET: Self-reset
Range: Self-reset, Latched, Disabled
GROUND TOC1 Range: Disabled, Enabled

MESSAGE
EVENTS: Disabled
This element can provide a desired time-delay operating characteristic versus the applied current or be used as a simple
definite time element. The ground current input value is the quantity measured by the ground input CT and is the funda-
mental phasor or RMS magnitude. Two methods of resetting operation are available: “Timed” and “Instantaneous” (refer to
the Inverse time overcurrent curve characteristics section for details). When the element is blocked, the time accumulator
will reset according to the reset characteristic. For example, if the element reset characteristic is set to “Instantaneous” and
the element is blocked, the time accumulator will be cleared immediately.
These elements measure the current that is connected to the ground channel of a CT/VT module. The conversion
range of a standard channel is from 0.02 to 46 times the CT rating.
NOTE
This channel may be also equipped with a sensitive input. The conversion range of a sensitive channel is from
0.002 to 4.6 times the CT rating.
NOTE
Figure 5–106: GROUND TOC1 SCHEME LOGIC

b) GROUND INSTANTANEOUS OVERCURRENT (ANSI 50G, IEC PIOC)

PATH: SETTINGS  GROUPED ELEMENTS  SETTING GROUP 1(6)  GROUND CURRENT  GROUND IOC1(2)
 GROUND IOC1 GROUND IOC1 Range: Disabled, Enabled

GROUND IOC1 SIGNAL Range: SRC 1, SRC 2, SRC 3, SRC 4
MESSAGE
SOURCE: SRC 1
GROUND IOC1 Range: 0.000 to 30.000 pu in steps of 0.001
MESSAGE
PICKUP: 1.000 pu
GROUND IOC1 PICKUP Range: 0.00 to 600.00 s in steps of 0.01
MESSAGE
DELAY: 0.00 s
GROUND IOC1 RESET Range: 0.00 to 600.00 s in steps of 0.01
MESSAGE
DELAY: 0.00 s
GROUND IOC1 BLOCK: Range: FlexLogic operand
MESSAGE
Off
GROUND IOC1 Range: Self-reset, Latched, Disabled
MESSAGE
TARGET: Self-reset
GROUND IOC1 Range: Disabled, Enabled
MESSAGE
EVENTS: Disabled
The ground instantaneous overcurrent element may be used as an instantaneous element with no intentional delay or as a
definite time element. The ground current input is the quantity measured by the ground input CT and is the fundamental
phasor magnitude. 5
These elements measure the current that is connected to the ground channel of a CT/VT module. The conversion
range of a standard channel is from 0.02 to 46 times the CT rating.
NOTE
This channel may be equipped with a standard or sensitive input. The conversion range of a sensitive channel is
from 0.002 to 4.6 times the CT rating.
NOTE
Figure 5–107: GROUND IOC1 SCHEME LOGIC

5.6.11 NEGATIVE SEQUENCE CURRENT
a) MAIN MENU
PATH: SETTINGS  GROUPED ELEMENTS  SETTING GROUP 1(6)  NEGATIVE SEQUENCE CURRENT
 NEGATIVE SEQUENCE  NEG SEQ TOC1

See page 5–211.
 CURRENT 
 NEG SEQ TOC2

 NEG SEQ IOC1

 NEG SEQ IOC2

 NEG SEQ DIR OC1

 NEG SEQ DIR OC2

The D60 relay provides two (2) negative-sequence time overcurrent elements, two (2) negative-sequence instantaneous
overcurrent elements, and two (2) negative-sequence directional overcurrent elements. For additional information on the
negative sequence time overcurrent curves, refer to the Inverse Time Overcurrent Curves section earlier.

b) NEGATIVE SEQUENCE TIME OVERCURRENT (ANSI 51Q, IEC PTOC)

PATH: SETTINGS  GROUPED ELEMENTS  SETTING GROUP 1(6)  NEGATIVE SEQUENCE CURRENT  NEG SEQ TOC1(2)
 NEG SEQ TOC1 NEG SEQ TOC1 Range: Disabled, Enabled

NEG SEQ TOC1 SIGNAL Range: SRC 1, SRC 2, SRC 3, SRC 4
MESSAGE
SOURCE: SRC 1
NEG SEQ TOC1 Range: 0.000 to 30.000 pu in steps of 0.001
MESSAGE
PICKUP: 1.000 pu
NEG SEQ TOC1 Range: see OVERCURRENT CURVE TYPES table
MESSAGE
CURVE: IEEE Mod Inv
NEG SEQ TOC1 Range: 0.00 to 600.00 in steps of 0.01
MESSAGE
TD MULTIPLIER: 1.00
NEG SEQ TOC1 Range: Instantaneous, Timed
MESSAGE
NEG SEQ TOC1 BLOCK: Range: FlexLogic operand
MESSAGE
Off
NEG SEQ TOC1 Range: Self-reset, Latched, Disabled
MESSAGE
TARGET: Self-reset
NEG SEQ TOC1 Range: Disabled, Enabled
MESSAGE
EVENTS: Disabled
5
The negative-sequence time overcurrent element may be used to determine and clear unbalance in the system. The input
for calculating negative-sequence current is the fundamental phasor value.
Two methods of resetting operation are available; “Timed” and “Instantaneous” (refer to the Inverse Time Overcurrent Char-
acteristics sub-section for details on curve setup, trip times and reset operation). When the element is blocked, the time
accumulator resets according to the reset characteristic. For example, if the element reset characteristic is set to “Instanta-
neous” and the element is blocked, the time accumulator is cleared immediately.
SETTING
NEG SEQ TOC1 INPUT:
NEG SEQ TOC1 PICKUP:
SETTING NEG SEQ TOC1 CURVE:
NEG SEQ TOC1 FUNCTION:

NEG SEQ TOC1 TD MULTIPLIER:
Enabled=1
FLEXLOGIC OPERANDS
NEG SEQ TOC1 RESET:
NEG SEQ TOC1 PKP
SETTING
AND RUN NEG SEQ < PICKUP NEG SEQ TOC1 DPO
NEG SEQ TOC1 BLOCK: NEG SEQ TOC1 OP
Off=0
t
SETTING
NEG SEQ TOC1 SOURCE:
Neg Seq 827057A5.CDR
Figure 5–108: NEGATIVE SEQUENCE TOC1 SCHEME LOGIC

c) NEGATIVE SEQUENCE INSTANTANEOUS OVERCURRENT (ANSI 50Q, IEC PIOC)

PATH: SETTINGS  GROUPED ELEMENTS  SETTING GROUP 1(6)  NEGATIVE SEQUENCE CURRENT  NEG SEQ OC1(2)
 NEG SEQ IOC1 NEG SEQ IOC1 Range: Disabled, Enabled

NEG SEQ IOC1 SIGNAL Range: SRC 1, SRC 2, SRC 3, SRC 4
MESSAGE
SOURCE: SRC 1
NEG SEQ IOC1 Range: 0.000 to 30.000 pu in steps of 0.001
MESSAGE
PICKUP: 1.000 pu
NEG SEQ IOC1 PICKUP Range: 0.00 to 600.00 s in steps of 0.01
MESSAGE
DELAY: 0.00 s
NEG SEQ IOC1 RESET Range: 0.00 to 600.00 s in steps of 0.01
MESSAGE
DELAY: 0.00 s
NEG SEQ IOC1 BLOCK: Range: FlexLogic operand
MESSAGE
Off
NEG SEQ IOC1 Range: Self-reset, Latched, Disabled
MESSAGE
TARGET: Self-reset
NEG SEQ IOC1 Range: Disabled, Enabled
MESSAGE
EVENTS: Disabled
The negative-sequence instantaneous overcurrent element may be used as an instantaneous function with no intentional
5 delay or as a definite time function. The element responds to the negative-sequence current fundamental frequency phasor
magnitude (calculated from the phase currents) and applies a positive-sequence restraint for better performance: a small
portion (12.5%) of the positive-sequence current magnitude is subtracted from the negative-sequence current magnitude
when forming the operating quantity:
I op = I_2 – K  I_1 where K = 1  8 (EQ 5.20)
The positive-sequence restraint allows for more sensitive settings by counterbalancing spurious negative-sequence cur-
rents resulting from:
• system unbalances under heavy load conditions
• transformation errors of current transformers (CTs) during three-phase faults
• fault inception and switch-off transients during three-phase faults
pickup). The operating quantity depends on the way the test currents are injected into the relay (single-phase injection:
I op = 0.2917  I injected ; three-phase injection, opposite rotation: I op = I injected ).
SETTING
SETTING
NEG SEQ IOC1 FUNCTION: NEG SEQ IOC1
SETTING PICKUP DELAY:
Enabled=1 FLEXLOGIC OPERANDS
NEG SEQ IOC1
NEG SEQ IOC1 PICKUP: NEG SEQ IOC1 PKP
RESET DELAY:
SETTING NEG SEQ IOC1 DPO
AND RUN tPKP
tRST NEG SEQ IOC1 OP
NEG SEQ IOC1 BLOCK: I_2 - K I_1 PICKUP
Off=0
SETTING
NEG SEQ IOC1 SOURCE:
I_2 827058A6.CDR
Figure 5–109: NEGATIVE SEQUENCE IOC1 SCHEME LOGIC

d) NEGATIVE SEQUENCE DIRECTIONAL OVERCURRENT (ANSI 67Q, IEC PDEF/PTOC)

PATH: SETTINGS  GROUPED ELEMENTS  SETTING GROUP 1(6)  NEGATIVE SEQUENCE CURRENT  NEG SEQ DIR OC1(2)
 NEG SEQ DIR OC1 NEG SEQ DIR OC1 Range: Disabled, Enabled
NEG SEQ DIR OC1 Range: SRC 1, SRC 2, SRC 3, SRC 4
MESSAGE
SOURCE: SRC 1
NEG SEQ DIR OC1 Range: 0.00 to 250.00 ohms in steps of 0.01
MESSAGE
OFFSET: 0.00 
NEG SEQ DIR OC1 Range: Neg Sequence, Zero Sequence
MESSAGE
TYPE: Neg Sequence
NEG SEQ DIR OC1 POS- Range: 0.000 to 0.500 in steps of 0.001
MESSAGE
SEQ RESTRAINT: 0.063
NEG SEQ DIR OC1 FWD Range: 0 to 90° Lag in steps of 1
MESSAGE
ECA: 75° Lag
NEG SEQ DIR OC1 FWD Range: 40 to 90° in steps of 1
MESSAGE
LIMIT ANGLE: 90°
NEG SEQ DIR OC1 FWD Range: 0.015 to 30.000 pu in steps of 0.001
MESSAGE
PICKUP: 0.050 pu
NEG SEQ DIR OC1 REV Range: 40 to 90° in steps of 1
MESSAGE
LIMIT ANGLE: 90°
NEG SEQ DIR OC1 REV Range: 0.015 to 30.000 pu in steps of 0.001 5
MESSAGE
PICKUP: 0.050 pu
NEG SEQ DIR OC1 BLK: Range: FlexLogic operand
MESSAGE
Off
NEG SEQ DIR OC1 Range: Self-reset, Latched, Disabled
MESSAGE
TARGET: Self-reset
NEG SEQ DIR OC1 Range: Disabled, Enabled
MESSAGE
EVENTS: Disabled
There are two negative-sequence directional overcurrent protection elements available. The element provides both forward
and reverse fault direction indications through its output operands NEG SEQ DIR OC1 FWD and NEG SEQ DIR OC1 REV,
respectively. The output operand is asserted if the magnitude of the operating current is above a pickup level (overcurrent
unit) and the fault direction is seen as forward or reverse, respectively (directional unit).
The overcurrent unit of the element essentially responds to the magnitude of a fundamental frequency phasor of either the
negative-sequence or neutral current as per user selection.
A positive-sequence restraint is applied for better performance: a small user-programmable portion of the positive-
sequence current magnitude is subtracted from the negative or zero-sequence current magnitude, respectively, when form-
ing the element operating quantity.
I op = I_2 – K  I_1 or I op = 3   I_0 – K  I_1  (EQ 5.21)
The positive-sequence restraint allows for more sensitive settings by counterbalancing spurious negative-sequence and
zero-sequence currents resulting from:
• System unbalances under heavy load conditions.
• Transformation errors of current transformers (CTs).
• Fault inception and switch-off transients.

The positive-sequence restraint must be considered when testing for pick-up accuracy and response time (multiple of
pickup). The positive-sequence restraint is removed for low currents. If the positive-sequence current is less than 0.8 pu,
then the restraint is removed by changing the constant K to zero. This results in better response to high-resistance faults
when the unbalance is very small and there is no danger of excessive CT errors, since the current is low.
The operating quantity depends on the way the test currents are injected into the D60. For single phase injection:
• Iop = ⅓  (1 – K  Iinjected for I_2 mode.
• Iop = (1 – K  Iinjected for I_0 mode if I_1 > 0.8 pu.
The directional unit uses the negative-sequence current (I_2) and negative-sequence voltage (V_2).
The following tables define the negative-sequence directional overcurrent element.
Table 5–29: NEGATIVE-SEQUENCE DIRECTIONAL OVERCURRENT UNIT
MODE OPERATING CURRENT
Negative-sequence Iop = |I_2| – K  I_1|
Zero-sequence Iop = 3 × (|I_0| – K × |I_1|) if |I_1| > 0.8 pu
Iop = 3 × |I_0| if |I_1| ≤ 0.8 pu
Table 5–30: NEGATIVE-SEQUENCE DIRECTIONAL UNIT

DIRECTION COMPARED PHASORS
Forward –V_2  Z_offset  I_2 I_2  1ECA
Reverse –V_2  Z_offset  I_2 –(I_2  1ECA)
Forward –V_2  Z_offset  I_2 I_2  1ECA
Reverse –V_2  Z_offset  I_2 –(I_2  1ECA)
5
The negative-sequence voltage must be greater than the VOLTAGE CUTOFF LEVEL setting specified in the PRODUCT SETUP
 DISPLAY PROPERTIES menu to be validated for use as a polarizing signal. If the polarizing signal is not validated neither
forward nor reverse indication is given. The following figure explains the usage of the voltage polarized directional unit of
the element.
The figure below shows the phase angle comparator characteristics for a phase A to ground fault, with settings of:
ECA = 75° (element characteristic angle = centerline of operating characteristic)
FWD LA = 80° (forward limit angle = ± the angular limit with the ECA for operation)
REV LA = 80° (reverse limit angle = ± the angular limit with the ECA for operation)

The element incorporates a current reversal logic: if the reverse direction is indicated for at least 1.25 of a power system
cycle, the prospective forward indication will be delayed by 1.5 of a power system cycle. The element is designed to emu-
late an electromechanical directional device. Larger operating and polarizing signals will result in faster directional discrimi-
nation bringing more security to the element operation.
–V_2 line
REV FWD
LA LA VAG (reference)
REV Operating
Region
LA
ECA line
LA ECA
I_2 line
–I_2 line LA
FWD Operating
Region
–ECA line
LA
VCG VBG
V_2 line
REV
LA
FWD
LA
5
827806A2.CDR
Figure 5–110: NEGATIVE-SEQUENCE DIRECTIONAL CHARACTERISTIC

The forward-looking function is designed to be more secure as compared to the reverse-looking function, and therefore
should be used for the tripping direction. The reverse-looking function is designed to be faster as compared to the forward-
looking function and should be used for the blocking direction. This allows for better protection coordination. Take this bias
into account when using the negative-sequence directional overcurrent element to directionalize other protection elements.
The negative-sequence directional pickup must be greater than the PRODUCT SETUP  DISPLAY PROPERTIES  CUR-
RENT CUT-OFF LEVEL setting value.
• NEG SEQ DIR OC1 OFFSET: This setting specifies the offset impedance used by this protection. The primary applica-
tion for the offset impedance is to guarantee correct identification of fault direction on series compensated lines (see
the Application of settings chapter for information on how to calculate this setting). In regular applications, the offset
impedance ensures proper operation even if the negative-sequence voltage at the relaying point is very small. If this is
the intent, the offset impedance shall not be larger than the negative-sequence impedance of the protected circuit.
Practically, it is several times smaller. The offset impedance is entered in secondary ohms. See the Theory of opera-
tion chapter for additional details.
• NEG SEQ DIR OC1 TYPE: This setting selects the operating mode for the overcurrent unit of the element. The
choices are “Neg Sequence” and “Zero Sequence”. In some applications it is advantageous to use a directional nega-
tive-sequence overcurrent function instead of a directional zero-sequence overcurrent function as inter-circuit mutual
effects are minimized.
• NEG SEQ DIR OC1 POS-SEQ RESTRAINT: This setting controls the positive-sequence restraint. Set to 0.063 (in
“Zero Sequence” mode) or 0.125 (in “Neg Sequence” mode) for backward compatibility with revisions 3.40 and earlier.
Set to zero to remove the restraint. Set higher if large system unbalances or poor CT performance are expected.
• NEG SEQ DIR OC1 FWD ECA: This setting select the element characteristic angle (ECA) for the forward direction.
The element characteristic angle in the reverse direction is the angle set for the forward direction shifted by 180°.
• NEG SEQ DIR OC1 FWD LIMIT ANGLE: This setting defines a symmetrical (in both directions from the ECA) limit
angle for the forward direction.

• NEG SEQ DIR OC1 FWD PICKUP: This setting defines the pickup level for the overcurrent unit in the forward direc-
tion. Upon NEG SEQ DIR OC1 TYPE selection, this pickup threshold applies to zero- or negative-sequence current. When
selecting this setting it must be kept in mind that the design uses a positive-sequence restraint technique.
• NEG SEQ DIR OC1 REV LIMIT ANGLE: This setting defines a symmetrical (in both directions from the ECA) limit
angle for the reverse direction.
• NEG SEQ DIR OC1 REV PICKUP: This setting defines the pickup level for the overcurrent unit in the reverse direc-
tion. Upon NEG SEQ DIR OC1 TYPE selection, this pickup threshold applies to zero- or negative-sequence current. When
selecting this setting it must be kept in mind that the design uses a positive-sequence restraint technique.
SETTINGS
Forward Pickup
Positive-Sequence Restraint
AND RUN
( |3I_0| – K × |I_1| ) ≥ Pickup

OR
AND RUN
( |I_2| – K × |I_1| ) ≥ Pickup AND
SETTING
Function
FLEXLOGIC OPERAND
Enabled = 1 SETTINGS AND NEG SEQ DIR OC1 FWD
Forward ECA
SETTING AND Forward Limit Angle
Block Reverse Limit Angle
Off = 0 Offset
TIMER
RUN
1.25 cycles
Forward AND
ACTUAL VALUES 1.5 cycles
V_2
I_2
I_0 Reverse
5 NOTE:
V_2 is negative-sequence voltage
I_2 is negative-sequence current
Voltage Polarization
I_0 is zero-sequence current

SETTINGS
Reverse Pickup
Pos Seq Restraint AND
AND RUN
SETTING
Type ( |I_2| – K × |I_1| ) ≥ Pickup
= Neg Sequence OR FLEXLOGIC OPERAND
AND RUN
= Zero Sequence NEG SEQ DIR OC1 REV
( |3I_0| – K × |I_1| ) ≥ Pickup
827091A7.CDR
Figure 5–111: NEGATIVE SEQUENCE DIRECTIONAL OC1 SCHEME LOGIC

5.6.12 BREAKER FAILURE
PATH: SETTINGS  GROUPED ELEMENTS  SETTING GROUP 1(6)  BREAKER FAILURE  BREAKER FAILURE 1(2)
 BREAKER FAILURE 1 BF1 FUNCTION: Range: Disabled, Enabled

 Disabled
BF1 MODE: Range: 3-Pole, 1-Pole

MESSAGE
3-Pole
BF1 SOURCE: Range: SRC 1, SRC 2, SRC 3, SRC 4

MESSAGE
SRC 1
BF1 USE AMP SUPV: Range: Yes, No
MESSAGE
Yes
BF1 USE SEAL-IN: Range: Yes, No
MESSAGE
Yes
BF1 3-POLE INITIATE: Range: FlexLogic operand
MESSAGE
Off
BF1 BLOCK: Range: FlexLogic operand
MESSAGE
Off
BF1 PH AMP SUPV Range: 0.001 to 30.000 pu in steps of 0.001
MESSAGE
PICKUP: 1.050 pu
BF1 N AMP SUPV Range: 0.001 to 30.000 pu in steps of 0.001
MESSAGE
PICKUP: 1.050 pu 5
BF1 USE TIMER 1: Range: Yes, No
MESSAGE
Yes
BF1 TIMER 1 PICKUP Range: 0.000 to 65.535 s in steps of 0.001
MESSAGE
DELAY: 0.000 s
MESSAGE
Yes
MESSAGE
DELAY: 0.000 s
MESSAGE
Yes
MESSAGE
DELAY: 0.000 s
BF1 BKR POS1 A/3P: Range: FlexLogic operand
MESSAGE
Off
BF1 BKR POS2 A/3P: Range: FlexLogic operand
MESSAGE
Off
BF1 BREAKER TEST ON: Range: FlexLogic operand
MESSAGE
Off
BF1 PH AMP HISET Range: 0.001 to 30.000 pu in steps of 0.001
MESSAGE
PICKUP: 1.050 pu
BF1 N AMP HISET Range: 0.001 to 30.000 pu in steps of 0.001
MESSAGE
PICKUP: 1.050 pu
BF1 PH AMP LOSET Range: 0.001 to 30.000 pu in steps of 0.001
MESSAGE
PICKUP: 1.050 pu

BF1 N AMP LOSET Range: 0.001 to 30.000 pu in steps of 0.001

MESSAGE
PICKUP: 1.050 pu
BF1 LOSET TIME Range: 0.000 to 65.535 s in steps of 0.001
MESSAGE
DELAY: 0.000 s
BF1 TRIP DROPOUT Range: 0.000 to 65.535 s in steps of 0.001
MESSAGE
DELAY: 0.000 s
BF1 TARGET Range: Self-reset, Latched, Disabled
MESSAGE
Self-Reset
BF1 EVENTS Range: Disabled, Enabled
MESSAGE
Disabled
BF1 PH A INITIATE: Range: FlexLogic operand
MESSAGE Valid only for 1-Pole breaker failure schemes.
Off
BF1 PH B INITIATE: Range: FlexLogic operand
Off
BF1 PH C INITIATE: Range: FlexLogic operand
Off
BF1 BKR POS1 B Range: FlexLogic operand
Off
BF1 BKR POS1 C Range: FlexLogic operand
Off
5 MESSAGE
BF1 BKR POS2 B Range: FlexLogic operand
Off Valid only for 1-Pole breaker failure schemes.
BF1 BKR POS2 C Range: FlexLogic operand

Off
In general, a breaker failure scheme determines that a breaker signaled to trip has not cleared a fault within a definite time,
so further tripping action must be performed. Tripping from the breaker failure scheme should trip all breakers, both local
and remote, that can supply current to the faulted zone. Usually operation of a breaker failure element will cause clearing of
a larger section of the power system than the initial trip. Because breaker failure can result in tripping a large number of
breakers and this affects system safety and stability, a very high level of security is required.
Two schemes are provided: one for three-pole tripping only (identified by the name “3BF”) and one for three pole plus sin-
gle-pole operation (identified by the name “1BF”). The philosophy used in these schemes is identical. The operation of a
breaker failure element includes three stages: initiation, determination of a breaker failure condition, and output.
INITIATION STAGE:
A FlexLogic operand representing the protection trip signal initially sent to the breaker must be selected to initiate the
scheme. The initiating signal should be sealed-in if primary fault detection can reset before the breaker failure timers have
finished timing. The seal-in is supervised by current level, so it is reset when the fault is cleared. If desired, an incomplete
sequence seal-in reset can be implemented by using the initiating operand to also initiate a FlexLogic timer, set longer than
any breaker failure timer, whose output operand is selected to block the breaker failure scheme.
For the D60 relay, the protection trip signal initially sent to the breaker is already programmed as a trip output. The
protection trip signal does not include other breaker commands that are not indicative of a fault in the protected
NOTE
zone.
Schemes can be initiated either directly or with current level supervision. It is particularly important in any application to
decide if a current-supervised initiate is to be used. The use of a current-supervised initiate results in the breaker failure ele-
ment not being initiated for a breaker that has very little or no current flowing through it, which may be the case for trans-
former faults. For those situations where it is required to maintain breaker fail coverage for fault levels below the BF1 PH
AMP SUPV PICKUP or the BF1 N AMP SUPV PICKUP setting, a current supervised initiate should not be used. This feature
should be utilized for those situations where coordinating margins may be reduced when high speed reclosing is used.
Thus, if this choice is made, fault levels must always be above the supervision pickup levels for dependable operation of

the breaker fail scheme. This can also occur in breaker-and-a-half or ring bus configurations where the first breaker closes
into a fault; the protection trips and attempts to initiate breaker failure for the second breaker, which is in the process of
closing, but does not yet have current flowing through it.
When the scheme is initiated, it immediately sends a trip signal to the breaker initially signaled to trip (this feature is usually
described as re-trip). This reduces the possibility of widespread tripping that results from a declaration of a failed breaker.
DETERMINATION OF A BREAKER FAILURE CONDITION:
The schemes determine a breaker failure condition via three paths. Each of these paths is equipped with a time delay, after
which a failed breaker is declared and trip signals are sent to all breakers required to clear the zone. The delayed paths are
associated with breaker failure timers 1, 2, and 3, which are intended to have delays increasing with increasing timer num-
bers. These delayed paths are individually enabled to allow for maximum flexibility.
Timer 1 logic (early path) is supervised by a fast-operating breaker auxiliary contact. If the breaker is still closed (as indi-
cated by the auxiliary contact) and fault current is detected after the delay interval, an output is issued. Operation of the
breaker auxiliary switch indicates that the breaker has mechanically operated. The continued presence of current indicates
that the breaker has failed to interrupt the circuit.
Timer 2 logic (main path) is not supervised by a breaker auxiliary contact. If fault current is detected after the delay interval,
an output is issued. This path is intended to detect a breaker that opens mechanically but fails to interrupt fault current; the
logic therefore does not use a breaker auxiliary contact.
The timer 1 and 2 paths provide two levels of current supervision, high-set and low-set, that allow the supervision level to
change from a current which flows before a breaker inserts an opening resistor into the faulted circuit to a lower level after
resistor insertion. The high-set detector is enabled after timeout of timer 1 or 2, along with a timer that will enable the low-
set detector after its delay interval. The delay interval between high-set and low-set is the expected breaker opening time.
Both current detectors provide a fast operating time for currents at small multiples of the pickup value. The overcurrent
detectors are required to operate after the breaker failure delay interval to eliminate the need for very fast resetting overcur-
rent detectors. 5
Timer 3 logic (slow path) is supervised by a breaker auxiliary contact and a control switch contact used to indicate that the
breaker is in or out-of-service, disabling this path when the breaker is out-of-service for maintenance. There is no current
level check in this logic as it is intended to detect low magnitude faults and it is therefore the slowest to operate.
OUTPUT:
The outputs from the schemes are:
• FlexLogic operands that report on the operation of portions of the scheme
• FlexLogic operand used to re-trip the protected breaker
• FlexLogic operands that initiate tripping required to clear the faulted zone. The trip output can be sealed-in for an
adjustable period.
• Target message indicating a failed breaker has been declared
• Illumination of the faceplate Trip LED (and the Phase A, B or C LED, if applicable)
MAIN PATH SEQUENCE:
ACTUAL CURRENT MAGNITUDE

FAILED INTERRUPTION
0
AMP CALCULATED CURRENT MAGNITUDE
CORRECT INTERRUPTION
Rampdown
0
PROTECTION OPERATION BREAKER INTERRUPTING TIME
(ASSUMED 1.5 cycles) (ASSUMED 3 cycles)
MARGIN BACKUP BREAKER OPERATING TIME
(Assumed 2 Cycles) (Assumed 3 Cycles)
BREAKER FAILURE TIMER No. 2 (±1/8 cycle)

INITIATE (1/8 cycle)
BREAKER FAILURE CURRENT DETECTOR PICKUP (1/8 cycle)

BREAKER FAILURE OUTPUT RELAY PICKUP (1/4 cycle)
FAULT cycles
OCCURS
0 1 2 3 4 5 6 7 8 9 10 11
827083A6.CDR
Figure 5–112: BREAKER FAILURE MAIN PATH SEQUENCE

The current supervision elements reset in less than 0.7 of a power cycle for any multiple of pickup current as shown below.
0.8
Margin
Maximum
Breaker failure reset time (cycles)

Average
0.6
0.4
0.2
0
0 20 40 60 80 100 120 140
MulWLple of pickup fault current
threshold setting 836769A4.CDR
Figure 5–113: BREAKER FAILURE OVERCURRENT SUPERVISION RESET TIME

SETTINGS:
• BF1 MODE: This setting is used to select the breaker failure operating mode: single or three pole.
• BF1 USE AMP SUPV: If set to "Yes", the element will only be initiated if current flowing through the breaker is above
5 •
the supervision pickup level.
BF1 USE SEAL-IN: If set to "Yes", the element will only be sealed-in if current flowing through the breaker is above the
supervision pickup level.
• BF1 3-POLE INITIATE: This setting selects the FlexLogic operand that will initiate three-pole tripping of the breaker.
• BF1 PH AMP SUPV PICKUP: This setting is used to set the phase current initiation and seal-in supervision level.
Generally this setting should detect the lowest expected fault current on the protected breaker. It can be set as low as
necessary (lower than breaker resistor current or lower than load current) – high-set and low-set current supervision
will guarantee correct operation.
• BF1 N AMP SUPV PICKUP: This setting is used to set the neutral current initiate and seal-in supervision level. Gener-
ally this setting should detect the lowest expected fault current on the protected breaker. Neutral current supervision is
used only in the three phase scheme to provide increased sensitivity. This setting is valid only for three-pole tripping
schemes.
• BF1 USE TIMER 1: If set to "Yes", the early path is operational.
• BF1 TIMER 1 PICKUP DELAY: Timer 1 is set to the shortest time required for breaker auxiliary contact Status-1 to
open, from the time the initial trip signal is applied to the breaker trip circuit, plus a safety margin.
• BF1 USE TIMER 2: If set to "Yes", the main path is operational.
• BF1 TIMER 2 PICKUP DELAY: Timer 2 is set to the expected opening time of the breaker, plus a safety margin. This
safety margin was historically intended to allow for measuring and timing errors in the breaker failure scheme equip-
ment. In microprocessor relays this time is not significant. In D60 relays, which use a Fourier transform, the calculated
current magnitude will ramp-down to zero one power frequency cycle after the current is interrupted, and this lag
should be included in the overall margin duration, as it occurs after current interruption. The Breaker failure main path
sequence diagram below shows a margin of two cycles; this interval is considered the minimum appropriate for most
applications.
Note that in bulk oil circuit breakers, the interrupting time for currents less than 25% of the interrupting rating can be
significantly longer than the normal interrupting time.
• BF1 USE TIMER 3: If set to "Yes", the Slow Path is operational.
• BF1 TIMER 3 PICKUP DELAY: Timer 3 is set to the same interval as timer 2, plus an increased safety margin.
Because this path is intended to operate only for low level faults, the delay can be in the order of 300 to 500 ms.

• BF1 BKR POS1 A/3P: This setting selects the FlexLogic operand that represents the protected breaker early-type
auxiliary switch contact (52/a). When using the single-pole breaker failure scheme, this operand represents the pro-
tected breaker early-type auxiliary switch contact on pole A. This is normally a non-multiplied form-A contact. The con-
tact may even be adjusted to have the shortest possible operating time.
• BF1 BKR POS2 A/3P: This setting selects the FlexLogic operand that represents the breaker normal-type auxiliary
switch contact (52/a). When using the single-pole breaker failure scheme, this operand represents the protected
breaker auxiliary switch contact on pole A. This may be a multiplied contact.
• BF1 BREAKER TEST ON: This setting is used to select the FlexLogic operand that represents the breaker in-service/
out-of-service switch set to the out-of-service position.
• BF1 PH AMP HISET PICKUP: This setting sets the phase current output supervision level. Generally this setting
should detect the lowest expected fault current on the protected breaker, before a breaker opening resistor is inserted.
• BF1 N AMP HISET PICKUP: This setting sets the neutral current output supervision level. Generally this setting
should detect the lowest expected fault current on the protected breaker, before a breaker opening resistor is inserted.
Neutral current supervision is used only in the three pole scheme to provide increased sensitivity. This setting is valid
only for three-pole breaker failure schemes.
• BF1 PH AMP LOSET PICKUP: This setting sets the phase current output supervision level. Generally this setting
should detect the lowest expected fault current on the protected breaker, after a breaker opening resistor is inserted
(approximately 90% of the resistor current).
• BF1 N AMP LOSET PICKUP: This setting sets the neutral current output supervision level. Generally this setting
should detect the lowest expected fault current on the protected breaker, after a breaker opening resistor is inserted
(approximately 90% of the resistor current). This setting is valid only for three-pole breaker failure schemes.
• BF1 LOSET TIME DELAY: Sets the pickup delay for current detection after opening resistor insertion.
• BF1 TRIP DROPOUT DELAY: This setting is used to set the period of time for which the trip output is sealed-in. This
timer must be coordinated with the automatic reclosing scheme of the failed breaker, to which the breaker failure ele-
5
ment sends a cancel reclosure signal. Reclosure of a remote breaker can also be prevented by holding a transfer trip
signal on longer than the reclaim time.
• BF1 PH A INITIATE / BF1 PH B INITIATE / BF 1 PH C INITIATE: These settings select the FlexLogic operand to initi-
ate phase A, B, or C single-pole tripping of the breaker and the phase A, B, or C portion of the scheme, accordingly.
This setting is only valid for single-pole breaker failure schemes.
• BF1 BKR POS1 B / BF1 BKR POS 1 C: These settings select the FlexLogic operand to represents the protected
breaker early-type auxiliary switch contact on poles B or C, accordingly. This contact is normally a non-multiplied Form-
A contact. The contact may even be adjusted to have the shortest possible operating time. This setting is valid only for
single-pole breaker failure schemes.
• BF1 BKR POS2 B: Selects the FlexLogic operand that represents the protected breaker normal-type auxiliary switch
contact on pole B (52/a). This may be a multiplied contact. This setting is valid only for single-pole breaker failure
schemes.
• BF1 BKR POS2 C: This setting selects the FlexLogic operand that represents the protected breaker normal-type
auxiliary switch contact on pole C (52/a). This may be a multiplied contact. For single-pole operation, the scheme has
the same overall general concept except that it provides re-tripping of each single pole of the protected breaker. The
approach shown in the following single pole tripping diagram uses the initiating information to determine which pole is
supposed to trip. The logic is segregated on a per-pole basis. The overcurrent detectors have ganged settings. This
setting is valid only for single-pole breaker failure schemes.
Upon operation of the breaker failure element for a single pole trip command, a three-pole trip command should be
given via output operand BKR FAIL 1 TRIP OP.

SETTINGS
Function
Enabled = 1
AND
Block
Off = 0
FLEXLOGIC OPERAND
TRIP PHASE A
from the trip output element
SETTING OR Initiated
Phase A Initiate to breaker failure
single-pole logic sheet 2
Off = 0 OR
FLEXLOGIC OPERAND OR FLEXLOGIC OPERAND
TRIP 3-POLE AND BKR FAIL 1 RETRIP A

OR Initiated phase A
SETTING
Three-Pole Initiate to breaker failure
Off = 0
SETTING
AND
Use Seal-In
Yes = 1
Seal-in path
No = 0
AND OR
SETTING OR
Use Current Supervision
Yes = 1
No = 0 OR
AND FLEXLOGIC OPERAND
FLEXLOGIC OPERAND AND BKR FAIL 1 RETRIP B
Seal-in path
5
TRIP PHASE B
Initiated phase B
OR OR
SETTING to breaker failure
Phase B Initiate
Off = 0
OR
FLEXLOGIC OPERAND
AND
TRIP PHASE C
OR FLEXLOGIC OPERAND
Seal-in path AND BKR FAIL 1 RETRIP C
SETTING
Phase C Initiate SETTING
Off = 0 Phase Current Initiated phase C
Supervision Pickup
to breaker failure
RUN single-pole logic sheet 2
IA ≥ Pickup
SETTING
SETTING
Source RUN OR
IA IB ≥ Pickup
IB RUN
IC IC ≥ Pickup
IC
to breaker failure
IB
IA 827069A9.CDR
Figure 5–114: SINGLE-POLE BREAKER FAILURE, INITIATE

)/(;/2*,&23(5$1'
25 %.5)$,/723
6(77,1*6
GE Multilin
%UHDNHU3RV3KDVH$3 )/(;/2*,&23(5$1'
2II 25 %.5)$,/723
8VH7LPHU
5 SETTINGS
6(77,1* 6(77,1*
1R 7LPHU3LFNXS'HOD\ $1' 3KDVH&XUUHQW+L6HW3LFNXS
<HV 581
25
$1' ,$ 3LFNXS

,QLWLDWHGSKDVH$
IURPVLQJOHSROHEUHDNHU 6(77,1*
IDLOXUHORJLFVKHHW 6(77,1*
7LPHU3LFNXS'HOD\ /R6HW7LPH'HOD\ 6(77,1*
3KDVH&XUUHQW/R6HW3LFNXS
6(77,1*
$1' 581
8VH7LPHU

<HV ,$ 3LFNXS
1R
6(77,1*
6(77,1*6
7LPHU3LFNXS'HOD\ $1' 6(77,1*
%UHDNHU3RV3KDVH%
3KDVH&XUUHQW+L6HW3LFNXS
2II
$1' 25 581

,QLWLDWHGSKDVH% ,% 3LFNXS
IDLOXUHORJLFVKHHW 6(77,1*
6(77,1* 7ULS'URSRXW'HOD\
7LPHU3LFNXS'HOD\
/R6HW7LPH'HOD\ 6(77,1* )/(;/2*,&23(5$1'
3KDVH&XUUHQW/R6HW3LFNXS 25 %.5)$,/75,323
$1'
6(77,1*6 581

%UHDNHU3RV3KDVH%
,% 3LFNXS
2II
6(77,1*
6(77,1*
$1' 3KDVH&XUUHQW+L6HW3LFNXS
7LPHU3LFNXS'HOD\
581
$1' 25 ,& 3LFNXS

,QLWLDWHGSKDVH&
IDLOXUHORJLFVKHHW 6(77,1* /R6HW7LPH'HOD\ 6(77,1*
7LPHU3LFNXS'HOD\
3KDVH&XUUHQW/R6HW3LFNXS
D60 Line Distance Protection System

581
$1'
,& 3LFNXS
,$
,%
,&
Figure 5–115: SINGLE-POLE BREAKER FAILURE, TIMERS

6(77,1*6
8VH7LPHU
<HV
%UHDNHU3RV3KDVH$3
2II 6(77,1*
%UHDNHU3RV3KDVH% 7LPHU3LFNXS'HOD\
2II )/(;/2*,&23(5$1'
%UHDNHU3RV3KDVH& $1' %.5)$,/723
2II
%UHDNHU7HVW2Q
2II
,QLWLDWHG
IURPVLQJOHSROHEUHDNHUIDLOXUHORJLFVKHHW $&'5
5.6 GROUPED ELEMENTS
5-223
5
Figure 5–116: THREE-POLE BREAKER FAILURE, INITIATE

Figure 5–117: THREE-POLE BREAKER FAILURE, TIMERS

5.6.13 VOLTAGE ELEMENTS
a) MAIN MENU
PATH: SETTINGS  GROUPED ELEMENTS  SETTING GROUP 1(6)  VOLTAGE ELEMENTS
 VOLTAGE ELEMENTS  PHASE

See page 5–228.
  UNDERVOLTAGE1
 PHASE
 UNDERVOLTAGE2
 PHASE
 OVERVOLTAGE1
 NEUTRAL OV1

 NEUTRAL OV2

 NEUTRAL OV3

 NEG SEQ OV1

 NEG SEQ OV2

5 MESSAGE
 NEG SEQ OV3

See page 5–231.
 AUXILIARY UV1

 AUXILIARY UV2

 AUXILIARY OV1

 AUXILIARY OV2

 COMPENSATED
 OVERVOLTAGE
These protection elements can be used for a variety of applications such as:
• Undervoltage Protection: For voltage sensitive loads, such as induction motors, a drop in voltage increases the
drawn current which may cause dangerous overheating in the motor. The undervoltage protection feature can be used
to either cause a trip or generate an alarm when the voltage drops below a specified voltage setting for a specified time
delay.
• Permissive Functions: The undervoltage feature may be used to block the functioning of external devices by operat-
ing an output relay when the voltage falls below the specified voltage setting. The undervoltage feature may also be
used to block the functioning of other elements through the block feature of those elements.
• Source Transfer Schemes: In the event of an undervoltage, a transfer signal may be generated to transfer a load
from its normal source to a standby or emergency power source.
The undervoltage elements can be programmed to have a definite time delay characteristic. The definite time curve oper-
ates when the voltage drops below the pickup level for a specified period of time. The time delay is adjustable from 0 to
600.00 seconds in steps of 0.01. The undervoltage elements can also be programmed to have an inverse time delay char-
acteristic.

The undervoltage delay setting defines the family of curves shown below.
D
T = ---------------------------------- (EQ 5.22)
V 
 1 – ------------------
 V pickup
where: T = operating time

D = undervoltage delay setting (D = 0.00 operates instantaneously)
V = secondary voltage applied to the relay
Vpickup = pickup level
Time (seconds)
5
% of voltage pickup
842788A1.CDR
Figure 5–118: INVERSE TIME UNDERVOLTAGE CURVES

At 0% of pickup, the operating time equals the UNDERVOLTAGE DELAY setting.
NOTE

b) PHASE UNDERVOLTAGE (ANSI 27P, IEC PTUV)

PATH: SETTINGS  GROUPED ELEMENTS  SETTING GROUP 1(6)  VOLTAGE ELEMENTS  PHASE UNDERVOLTAGE1(3)
 PHASE PHASE UV1 Range: Disabled, Enabled

 UNDERVOLTAGE1 FUNCTION: Disabled
PHASE UV1 SIGNAL Range: SRC 1, SRC 2, SRC 3, SRC 4
MESSAGE
SOURCE: SRC 1
PHASE UV1 MODE: Range: Phase to Ground, Phase to Phase
MESSAGE
Phase to Ground
PHASE UV1 Range: 0.000 to 3.000 pu in steps of 0.001
MESSAGE
PICKUP: 1.000 pu
PHASE UV1 Range: Definite Time, Inverse Time
MESSAGE
CURVE: Definite Time
PHASE UV1 Range: 0.00 to 600.00 s in steps of 0.01
MESSAGE
DELAY: 1.00 s
PHASE UV1 MINIMUM Range: 0.000 to 3.000 pu in steps of 0.001
MESSAGE
VOLTAGE: 0.100 pu
PHASE UV1 BLOCK: Range: FlexLogic operand
MESSAGE
Off
PHASE UV1 Range: Self-reset, Latched, Disabled
MESSAGE
TARGET: Self-reset
5 PHASE UV1 Range: Disabled, Enabled
MESSAGE
EVENTS: Disabled
This element may be used to give a desired time-delay operating characteristic versus the applied fundamental voltage
(phase-to-ground or phase-to-phase for wye VT connection, or phase-to-phase for delta VT connection) or as a definite
time element. The element resets instantaneously if the applied voltage exceeds the dropout voltage. The delay setting
selects the minimum operating time of the phase undervoltage. The minimum voltage setting selects the operating voltage
below which the element is blocked (a setting of “0” will allow a dead source to be considered a fault condition).
Figure 5–119: PHASE UNDERVOLTAGE1 SCHEME LOGIC

c) PHASE OVERVOLTAGE (ANSI 59P, IEC PTOV)

PATH: SETTINGS  GROUPED ELEMENTS  SETTING GROUP 1(6)  VOLTAGE ELEMENTS  PHASE OVERVOLTAGE1
 PHASE PHASE OV1 Range: Disabled, Enabled

 OVERVOLTAGE1 FUNCTION: Disabled
PHASE OV1 SIGNAL Range: SRC 1, SRC 2, SRC 3, SRC 4
MESSAGE
SOURCE: SRC 1
PHASE OV1 Range: 0.000 to 3.000 pu in steps of 0.001
MESSAGE
PICKUP: 1.000 pu
PHASE OV1 PICKUP Range: 0.00 to 600.00 s in steps of 0.01
MESSAGE
DELAY: 1.00 s
PHASE OV1 RESET Range: 0.00 to 600.00 s in steps of 0.01
MESSAGE
DELAY: 1.00 s
PHASE OV1 BLOCK: Range: FlexLogic Operand
MESSAGE
Off
PHASE OV1 Range: Self-reset, Latched, Disabled
MESSAGE
TARGET: Self-reset
PHASE OV1 Range: Disabled, Enabled
MESSAGE
EVENTS: Disabled
The phase overvoltage element may be used as an instantaneous element with no intentional time delay or as a definite
time element. The input voltage is the phase-to-phase voltage, either measured directly from delta-connected VTs or as cal-
culated from phase-to-ground (wye) connected VTs. The specific voltages to be used for each phase are shown below. 5
SETTINGS
SETTING
PHASE OV1 PICKUP
PHASE OV1 SETTING DELAY:
FUNCTION: FLEXLOGIC OPERANDS
PHASE OV1 PHASE OV1 RESET
Disabled = 0 PICKUP: DELAY: PHASE OV1 A PKP
Enabled = 1 PHASE OV1 A DPO
RUN tPKP
VAB ≥ PICKUP PHASE OV1 A OP
tRST
PHASE OV1 B PKP
SETTING AND RUN tPKP PHASE OV1 B DPO
PHASE OV1 VBC ≥ PICKUP
BLOCK: PHASE OV1 B OP
tRST
RUN PHASE OV1 C PKP
Off = 0
VCA ≥ PICKUP tPKP PHASE OV1 C DPO
PHASE OV1 C OP
tRST
SETTING
PHASE OV1
SOURCE: FLEXLOGIC OPERAND
Source VT = Delta OR PHASE OV1 OP
VAB
VBC
FLEXLOGIC OPERAND
VCA
AND PHASE OV1 DPO
Source VT = Wye
FLEXLOGIC OPERAND
OR PHASE OV1 PKP
827066A7.CDR
Figure 5–120: PHASE OVERVOLTAGE SCHEME LOGIC

If the source VT is wye-connected, then the phase overvoltage pickup condition is V  3  Pickup for VAB, VBC,
and VCA.
NOTE

d) NEUTRAL OVERVOLTAGE (ANSI 59N, IEC PTOV)

PATH: SETTINGS  GROUPED ELEMENTS  SETTING GROUP 1(6)  VOLTAGE ELEMENTS  NEUTRAL OV1(3)
 NEUTRAL OV1 NEUTRAL OV1 Range: Disabled, Enabled

NEUTRAL OV1 SIGNAL Range: SRC 1, SRC 2, SRC 3, SRC 4
MESSAGE
SOURCE: SRC 1
NEUTRAL OV1 PICKUP: Range: 0.000 to 3.000 pu in steps of 0.001
MESSAGE
0.300 pu
NEUTRAL OV1 CURVE: Range: Definite time, FlexCurve A, FlexCurve B,
MESSAGE FlexCurve C
Definite time
NEUTRAL OV1 PICKUP: Range: 0.00 to 600.00 s in steps of 0.01
MESSAGE
DELAY: 1.00 s
NEUTRAL OV1 RESET: Range: 0.00 to 600.00 s in steps of 0.01
MESSAGE
DELAY: 1.00 s
NEUTRAL OV1 BLOCK: Range: FlexLogic operand
MESSAGE
Off
NEUTRAL OV1 TARGET: Range: Self-reset, Latched, Disabled
MESSAGE
Self-reset
NEUTRAL OV1 EVENTS: Range: Disabled, Enabled
MESSAGE
Disabled
5 There are three neutral overvoltage elements available. The neutral overvoltage element can be used to detect asymmetri-
cal system voltage condition due to a ground fault or to the loss of one or two phases of the source. The element responds
to the system neutral voltage (3V_0), calculated from the phase voltages. The nominal secondary voltage of the phase volt-
age channels entered under SETTINGS  SYSTEM SETUP  AC INPUTS  VOLTAGE BANK  PHASE VT SECONDARY is the
p.u. base used when setting the pickup level.
The neutral overvoltage element can provide a time-delayed operating characteristic versus the applied voltage (initialized
from FlexCurves A, B, or C) or be used as a definite time element. The NEUTRAL OV1 PICKUP DELAY setting applies only if
the NEUTRAL OV1 CURVE setting is “Definite time”. The source assigned to this element must be configured for a phase VT.
VT errors and normal voltage unbalance must be considered when setting this element. This function requires the VTs to
be wye-connected.
SETTING
NEUTRAL OV1
FUNCTION:
SETTING SETTING
Enabled=1
NEUTRAL OV1 PICKUP
NEUTRAL OV1 PICKUP: DELAY :
SETTING
AND RUN NEUTRAL OV1 RESET
DELAY :
NEUTRAL OV1 BLOCK:
NEUTRAL OV1 CURVE :
Off=0
FLEXLOGIC OPERANDS
3V_0< Pickup tPKP
t NEUTRAL OV1 OP
SETTING tRST
NEUTRAL OV1 DPO
NEUTRAL OV1 SIGNAL
SOURCE: NEUTRAL OV1 PKP
ZERO SEQ VOLT (V_0)
827848A3.CDR
Figure 5–121: NEUTRAL OVERVOLTAGE1 SCHEME LOGIC

e) NEGATIVE SEQUENCE OVERVOLTAGE (ANSI 59Q, IEC PTOV)

PATH: SETTINGS  GROUPED ELEMENTS  SETTING GROUP 1(6)  VOLTAGE ELEMENTS  NEG SEQ OV1(3)
 NEG SEQ OV1 NEG SEQ OV1 Range: Disabled, Enabled

NEG SEQ OV1 SIGNAL Range: SRC 1, SRC 2, SRC 3, SRC 4
MESSAGE
SOURCE: SRC 1
NEG SEQ OV1 PICKUP: Range: 0.000 to 1.250 pu in steps of 0.001
MESSAGE
0.300 pu
NEG SEQ OV1 PICKUP Range: 0.00 to 600.00 s in steps of 0.01
MESSAGE
DELAY: 0.50 s
NEG SEQ OV1 RESET Range: 0.00 to 600.00 s in steps of 0.01
MESSAGE
DELAY: 0.50 s
NEG SEQ OV1 BLOCK: Range: FlexLogic operand
MESSAGE
Off
NEG SEQ OV1 TARGET: Range: Self-reset, Latched, Disabled
MESSAGE
Self-reset
NEG SEQ OV1 EVENTS: Range: Disabled, Enabled
MESSAGE
Disabled
There are three negative-sequence overvoltage elements available.

The negative-sequence overvoltage element may be used to detect loss of one or two phases of the source, a reversed
phase sequence of voltage, or a non-symmetrical system voltage condition.
5
SETTING
NEG SEQ OV1
FUNCTION:
SETTING
Enabled = 1
NEG SEQ OV1 PICKUP: SETTINGS
SETTING NEG SEQ OV1 PICKUP
AND RUN DELAY:
NEG SEQ OV1 BLOCK: FLEXLOGIC OPERANDS
NEG SEQ OV1 RESET
NEG SEQ OV1 PKP
DELAY:
Off = 0 NEG SEQ OV1 DPO
t PKP
t RST NEG SEQ OV1 OP
SETTING V_2 > PICKUP
NEG SEQ OV1 SIGNAL
SOURCE:
NEG SEQ VOLTAGE V_2
827839A4.CDR
Figure 5–122: NEGATIVE-SEQUENCE OVERVOLTAGE SCHEME LOGIC

f) AUXILIARY UNDERVOLTAGE (ANSI 27X, IEC PTUV)

PATH: SETTINGS  GROUPED ELEMENTS  SETTING GROUP 1(6)  VOLTAGE ELEMENTS  AUXILIARY UV1(2)
 AUXILIARY UV1 AUX UV1 Range: Disabled, Enabled

AUX UV1 SIGNAL Range: SRC 1, SRC 2, SRC 3, SRC 4
MESSAGE
SOURCE: SRC 1
AUX UV1 PICKUP: Range: 0.000 to 3.000 pu in steps of 0.001
MESSAGE
0.700 pu
AUX UV1 CURVE: Range: Definite Time, Inverse Time
MESSAGE
Definite Time
AUX UV1 DELAY: Range: 0.00 to 600.00 s in steps of 0.01
MESSAGE
1.00 s
AUX UV1 MINIMUM: Range: 0.000 to 3.000 pu in steps of 0.001
MESSAGE
VOLTAGE: 0.100 pu
AUX UV1 BLOCK: Range: FlexLogic operand
MESSAGE
Off
AUX UV1 TARGET: Range: Self-reset, Latched, Disabled
MESSAGE
Self-reset
AUX UV1 EVENTS: Range: Disabled, Enabled
MESSAGE
Disabled
5 The D60 contains one auxiliary undervoltage element for each VT bank. This element is intended for monitoring undervolt-
age conditions of the auxiliary voltage. The AUX UV1 PICKUP selects the voltage level at which the time undervoltage ele-
ment starts timing. The nominal secondary voltage of the auxiliary voltage channel entered under SETTINGS  SYSTEM
SETUP  AC INPUTS  VOLTAGE BANK X5  AUXILIARY VT X5 SECONDARY is the per-unit base used when setting the
pickup level.
The AUX UV1 DELAY setting selects the minimum operating time of the auxiliary undervoltage element. Both AUX UV1 PICKUP
and AUX UV1 DELAY settings establish the operating curve of the undervoltage element. The auxiliary undervoltage element
can be programmed to use either definite time delay or inverse time delay characteristics. The operating characteristics
and equations for both definite and inverse time delay are as for the phase undervoltage element.
The element resets instantaneously. The minimum voltage setting selects the operating voltage below which the element is
blocked.
SETTING
AUX UV1 SETTING
FUNCTION:
AUX UV1 PICKUP:
Enabled=1
AUX UV1 CURVE:

SETTING
AUX UV1 BLOCK: AUX UV1 DELAY:

FLEXLOGIC OPERANDS
Off=0 AND RUN Vx < Pickup AUX UV1 PKP
AUX UV1 DPO
SETTING
SETTING t AUX UV1 OP
AUX UV1 MINIMUM
AUX UV1 SIGNAL VOLTAGE:
SOURCE:
AUX VOLT Vx Vx < Minimum
V
827849A3.CDR
Figure 5–123: AUXILIARY UNDERVOLTAGE SCHEME LOGIC

g) AUXILIARY OVERVOLTAGE (ANSI 59X, IEC PTOV)

PATH: SETTINGS  GROUPED ELEMENTS  SETTING GROUP 1(6)  VOLTAGE ELEMENTS  AUXILIARY OV1(2)
 AUXILIARY OV1 AUX OV1 Range: Disabled, Enabled

AUX OV1 SIGNAL Range: SRC 1, SRC 2, SRC 3, SRC 4
MESSAGE
SOURCE: SRC 1
AUX OV1 PICKUP: Range: 0.000 to 3.000 pu in steps of 0.001
MESSAGE
0.300 pu
AUX OV1 PICKUP Range: 0.00 to 600.00 s in steps of 0.01
MESSAGE
DELAY: 1.00 s
AUX OV1 RESET Range: 0.00 to 600.00 s in steps of 0.01
MESSAGE
DELAY: 1.00 s
AUX OV1 BLOCK: Range: FlexLogic operand
MESSAGE
Off
AUX OV1 TARGET: Range: Self-reset, Latched, Disabled
MESSAGE
Self-reset
AUX OV1 EVENTS: Range: Disabled, Enabled
MESSAGE
Disabled
The D60 contains one auxiliary overvoltage element for each VT bank. This element is intended for monitoring overvoltage
conditions of the auxiliary voltage. The nominal secondary voltage of the auxiliary voltage channel entered under SYSTEM
SETUP  AC INPUTS  VOLTAGE BANK X5  AUXILIARY VT X5 SECONDARY is the per-unit (pu) base used when setting the 5
pickup level.
A typical application for this element is monitoring the zero-sequence voltage (3V_0) supplied from an open-corner-delta
VT connection.
SETTING
AUX OV1
FUNCTION:
SETTING
Enabled=1
AUX OV1 PICKUP: SETTING
SETTING
AND RUN AUX OV1 PICKUP
DELAY :
AUX OV1 BLOCK:
AUX OV1 RESET
Off=0 DELAY :
FLEXLOGIC OPERANDS
Vx < Pickup tPKP
SETTING tRST AUX OV1 OP
AUX OV1 DPO
AUX OV1 SIGNAL
SOURCE: AUX OV1 PKP
AUXILIARY VOLT (Vx)
827836A3.CDR
Figure 5–124: AUXILIARY OVERVOLTAGE SCHEME LOGIC

h) COMPENSATED OVERVOLTAGE (ANSI 59P, IEC PTOV)

PATH: SETTINGS  GROUPED ELEMENTS  SETTING GROUP 1(6)  VOLTAGE ELEMENTS  COMPENSATED OVERVOLTAGE
 COMPENSATED COMPENSATED OV Range: Disabled, Enabled

 OVERVOLTAGE FUNCTION: Disabled
COMPENSATED OV Range: SRC 1, SRC 2, SRC 3, SRC 4
MESSAGE
SOURCE: SRC 1
COMPENSATED OV Zc Range: 0.00 to 500.00 ohms in steps of 0.01
MESSAGE
MAG: 2.00 Ω
COMPENSATED OV Zc Range: 30 to 90° in steps of 1
MESSAGE
ANG: 90°
COMPENSATED OV Range: 0.01 to 1.00 pu in steps of 0.01
MESSAGE
I_1max: 0.20 pu
COMPENSATED OV STG1 Range: 0.250 to 3.000 pu in steps of 0.01
MESSAGE
PICKUP: 1.300 pu
COMPENSATED OV STG1 Range: 0.00 to 600.00 seconds in steps of 0.01
MESSAGE
DELAY: 1.00 s
COMPENSATED OV STG2 Range: 0.250 to 3.000 pu in steps of 0.01
MESSAGE
PICKUP: 1.300 pu
MESSAGE
DELAY: 1.00 s
5 COMPENSATED OV STG3 Range: 0.250 to 3.000 pu in steps of 0.01
MESSAGE
PICKUP: 1.300 pu
MESSAGE
DELAY: 1.00 s
COMPENSATED OV BLK: Range: FlexLogic operand
MESSAGE
Off
COMPENSATED OV Range: Self-reset, Latched, Disabled
MESSAGE
TARGET: Self-reset
COMPENSATED OV Range: Disabled, Enabled
MESSAGE
EVENTS: Disabled
The compensated overvoltage function is intended to provide protection against an overvoltage due to the opening of the
remote terminal of a transmission line – the so called the Ferranti effect. This could be achieved using a transfer-tripping
scheme. However, with high voltage, more corona may exist on the line and inhibit the proper reception of a carrier-trans-
fer-trip signal. Also, the presence of a line with an open terminal in weak systems can raise the voltage level of the local
bus. Detecting and tripping a line with an open terminal can prevent tripping at the local bus in this case.
/RFDO 5HPRWH
WHUPLQDO WHUPLQDO
=F
,B
9B 9B&
$&'5
Figure 5–125: TRANSMISSION LINE WITH REMOTE TERMINAL OPEN

,B
9B 9BF
,Bî=F
$&'5
Figure 5–126: PHASOR DIAGRAM

The function approximates the voltage rise at the far end of the transmission line according to the following relationship:
jZ 
V_1 – I_1  Z C_mag  e C_ang
V_1 C  pu  = ------------------------------------------------------------------------------
- (EQ 5.23)
V nominal
In the above equation:

• V_1 is the positive-sequence voltage (phasor quantity) in secondary volts measured at the local terminal.
• I_1 is the positive-sequence current (phasor quantity) in secondary amps measured at the local terminal.
• Vnominal is the phase VT secondary setting in the case of wye VTs and the phase VT secondary setting dividec by √3 in
the case of delta VTs.
• ZC_mag and ZC_ang represent an impedance between the local and remote terminals.
• V_1C is the calculated positive-sequence voltage magnitude at the remote terminal.
If the magnitude of ZC is set to one-half the series impedance of the line (R + jXL), the compensated voltage will be approx-
imately equal to the positive-sequence voltage at the remote end of the line. A more accurate setting of ZC may be made if
the positive-sequence charging current and the voltages at the local and remote line ends resulting from an open breaker
are known. In this case, the desired reach setting would be:
V local – V remote
5
ZC = ---------------------------------------- (EQ 5.24)
I ch arg e
The following settings are available.

• COMPENSATED OV Zc MAG: This setting specifies the magnitude of the impedance ZC in secondary ohms. This
should be set to half the positive-sequence series impedance of the line. Alternately, if the positive-sequence charging
currents and local and remote voltages are known, then this value can be calculated from equation above.
• COMPENSATED OV Zc ANG: This setting specifies the angle of the impedance ZC in degrees.
• COMPENSATED OV I_1max: This setting specifies the maximum expected positive-sequence line current for which a
remote overvoltage is anticipated.
• COMPENSATED OV STG1 PKP, COMPENSATED OV STG2 PKP, COMPENSATED OV STG3 PKP: These settings
specify the pickup level for each of the three stages. If any stage is set with no intentional time delay, then the pickup
setting should be set 15% above the anticipated steady state overvoltage to prevent an operation during line energiza-
tion. A stage that is not used may be set to its maximum setting value (3.000 pu) to effectively disable it.
• COMPENSATED OV STG1 DELAY, COMPENSATED OV STG2 DELAY, COMPENSATED OV STG3 DELAY: These
settings specify the time delay for each of the three stages in seconds.
The compensated overvoltage scheme logic is shown below.

Figure 5–127: COMPENSATED OVERVOLTAGE LOGIC

5.6.14 SENSITIVE DIRECTIONAL POWER
PATH: SETTINGS  GROUPED ELEMENTS  SETTING GROUP 1(6)  POWER  SENSITIVE DIRECTIONAL POWER
 DIRECTIONAL POWER 1(2)
 DIRECTIONAL DIR POWER 1 Range: Disabled, Enabled
 POWER 1 FUNCTION: Disabled
DIR POWER 1 Range: SRC 1, SRC 2, SRC 3, SRC 4
MESSAGE
SOURCE: SRC 1
DIR POWER 1 Range: 0 to 359° in steps of 1
MESSAGE
RCA: 0°
DIR POWER 1 Range: 0 to 0.95° in steps of 0.05
MESSAGE
CALIBRATION: 0.00°
DIR POWER 1 STG1 Range: –1.200 to 1.200 pu in steps of 0.001
MESSAGE
SMIN: 0.100 pu
DIR POWER 1 STG1 Range: 0.00 to 600.00 s in steps of 0.01
MESSAGE
DELAY: 0.50 s
DIR POWER 1 STG2 Range: –1.200 to 1.200 pu in steps of 0.001
MESSAGE
SMIN: 0.100 pu
DIR POWER 1 STG2 Range: 0.00 to 600.00 s in steps of 0.01
MESSAGE
DELAY: 20.00 s
MESSAGE
DIR POWER 1 BLK: Range: FlexLogic operand
5
Off
DIR POWER 1 Range: Self-Reset, Latched, Disabled
MESSAGE
TARGET: Self-Reset
DIR POWER 1 Range: Disabled, Enabled
MESSAGE
EVENTS: Disabled
The sensitive directional power element responds to three-phase directional power and is designed for reverse power and
low forward power applications for synchronous machines or interconnections involving co-generation. The relay measures
the three-phase power from either full set of wye-connected VTs or full-set of delta-connected VTs. In the latter case, the
two-wattmeter method is used. Refer to the UR-series metering conventions section in chapter 6 for details regarding the
active and reactive powers used by the sensitive directional power element.
The element has an adjustable characteristic angle and minimum operating power as shown in the Directional power char-
acteristic diagram. The element responds to the following condition:
P cos  + Q sin   SMIN (EQ 5.25)
where: P and Q are active and reactive powers as measured per the UR-series metering convention,
 is a sum of the element characteristic (DIR POWER 1 RCA) and calibration (DIR POWER 1 CALIBRATION) angles, and
SMIN is the minimum operating power
The operating quantity is displayed in the ACTUAL VALUES  METERING  SENSITIVE DIRECTIONAL POWER 1(2) actual
value. The element has two independent (as to the pickup and delay settings) stages for alarm and trip, respectively.

n
io
ct
re
Di
OPERATE
RCA+
CALIBRATION
SMIN
P
+
RESTRAIN
-
Figure 5–128: DIRECTIONAL POWER CHARACTERISTIC

By making the characteristic angle adjustable and providing for both negative and positive values of the minimum operating
power a variety of operating characteristics can be achieved as presented in the figure below. For example, section (a) in
the figure below shows settings for reverse power, while section (b) shows settings for low forward power applications.
(a) Q (b) Q
RESTRAIN
OPERATE RESTRAIN OPERATE
P P
5 RCA = 180o
SMIN > 0
RCA = 180o
SMIN < 0
(c) Q (d) Q
OPERATE OPERATE
P P
RESTRAIN RESTRAIN
RCA = 0o RCA = 0o
SMIN < 0 SMIN > 0
(e) Q
OPERATE
(f) Q
RESTRAIN
RESTRAIN OPERATE
P P
RCA = 90o RCA = 270o

SMIN > 0 SMIN < 0
842702A1.CDR
Figure 5–129: DIRECTIONAL POWER ELEMENT SAMPLE APPLICATIONS

• DIR POWER 1 RCA: Specifies the relay characteristic angle (RCA) for the sensitive directional power function. Appli-
cation of this setting is threefold:
1. It allows the element to respond to active or reactive power in any direction (active overpower/underpower, etc.).
2. Together with a precise calibration angle, it allows compensation for any CT and VT angular errors to permit more
sensitive settings.
3. It allows for required direction in situations when the voltage signal is taken from behind a delta-wye connected
power transformer and the phase angle compensation is required.
For example, the active overpower characteristic is achieved by setting DIR POWER 1 RCA to “0°”, reactive overpower by
setting DIR POWER 1 RCA to “90°”, active underpower by setting DIR POWER 1 RCA to “180°”, and reactive underpower by
setting DIR POWER 1 RCA to “270°”.
• DIR POWER 1 CALIBRATION: This setting allows the relay characteristic angle to change in steps of 0.05°. This may
be useful when a small difference in VT and CT angular errors is to be compensated to permit more sensitive settings.
This setting virtually enables calibration of the directional power function in terms of the angular error of applied VTs
and CTs. The element responds to the sum of the DIR POWER 1 RCA and DIR POWER 1 CALIBRATION settings.
• DIR POWER 1 STG1 SMIN: This setting specifies the minimum power as defined along the relay characteristic angle
(RCA) for the stage 1 of the element. The positive values imply a shift towards the operate region along the RCA line;
the negative values imply a shift towards the restrain region along the RCA line. Refer to the Directional power sample
applications figure for details. Together with the RCA, this setting enables a wide range of operating characteristics.
This setting applies to three-phase power and is entered in per-unit (pu) values. The base quantity is 3-phase power
on primary side, which is calculated as 3 x Phase CT Primary x Phase VT Ratio x Phase VT Secondary in case of
delta connected VTs; and 3 x Phase CT Primary x Phase VT Ratio x Phase VT Secondary in case of wye connected
VTs.
For example, a setting of 2% for a 200 MW machine is 0.02  200 MW = 4 MW. If 7.967 kV is a primary VT voltage and
10 kA is a primary CT current, the source pu quantity is 239 MVA, and thus, SMIN should be set at 4 MW / 239 MVA = 5
0.0167 pu  0.017 pu. If the reverse power application is considered, RCA = 180° and SMIN = 0.017 pu.
The element drops out if the magnitude of the positive-sequence current becomes virtually zero, that is, it drops below
the cutoff level.
• DIR POWER 1 STG1 DELAY: This setting specifies a time delay for stage 1. For reverse power or low forward power
applications for a synchronous machine, stage 1 is typically applied for alarming and stage 2 for tripping.
SETTING
DIR POWER 1
FUNCTION:
Enabled = 1
SETTINGS SETTING
SETTING DIR POWER 1 RCA: DIR POWER 1 STG1
DIR POWER 1 BLK: DELAY:
AND
DIR POWER 1 tPKP

CALIBRATION:
Off = 0
DIR POWER 1 STG1 100 ms
SMIN:
FLEXLOGIC OPERANDS
DIR POWER 1 STG2 FLEXLOGIC™ OPERANDS
SETTING SMIN: DIR POWER 1 STG1 OP
RUN DIR POWER 1 STG1 DPO
DIR POWER 1 SOURCE: DIR POWER 1 DPO
DIR POWER 1 STG1 PKP
OR
DIRECTIONAL POWER DIR POWER 1 PKP

Three-phase active power (P)
CHARACTERISTICS DIR POWER 1 STG2 PKP
OR
DIR POWER 1 OP
Three-phase reactive power (Q)
DIR POWER 1 STG2 DPO
DIR POWER 1 STG2 OP
SETTING
DIR POWER 1 STG2
DELAY:
tPKP
100 ms
842003A3.CDR
Figure 5–130: SENSITIVE DIRECTIONAL POWER SCHEME LOGIC

5.7 CONTROL ELEMENTS 5 SETTINGS
5.7CONTROL ELEMENTS 5.7.1 OVERVIEW
Control elements are generally used for control rather than protection. See the Introduction to Elements section at the
beginning of this chapter for further information.
5.7.2 TRIP BUS
PATH: SETTINGS  CONTROL ELEMENTS  TRIP BUS  TRIP BUS 1(6)
 TRIP BUS 1 TRIP BUS 1 Range: Enabled, Disabled

TRIP BUS 1 BLOCK: Range: FlexLogic operand
MESSAGE
Off
TRIP BUS 1 PICKUP Range: 0.00 to 600.00 s in steps of 0.01
MESSAGE
DELAY: 0.00 s
TRIP BUS 1 RESET Range: 0.00 to 600.00 s in steps of 0.01
MESSAGE
DELAY: 0.00 s
TRIP BUS 1 INPUT 1: Range: FlexLogic operand
MESSAGE
Off
TRIP BUS 1 INPUT 2: Range: FlexLogic operand
MESSAGE
Off

5 TRIP BUS 1 INPUT 16: Range: FlexLogic operand
MESSAGE
Off
TRIP BUS 1 Range: Enabled, Disabled
MESSAGE
LATCHING: Disabled
TRIP BUS 1 RESET: Range: FlexLogic operand
MESSAGE
Off
TRIP BUS 1 TARGET: Range: Self-reset, Latched, Disabled
MESSAGE
Self-reset
TRIP BUS 1 Range: Enabled, Disabled
MESSAGE
EVENTS: Disabled
The trip bus element allows aggregating outputs of protection and control elements without using FlexLogic and assigning
them a simple and effective manner. Each trip bus can be assigned for either trip or alarm actions. Simple trip conditioning
such as latch, delay, and seal-in delay are available.
The easiest way to assign element outputs to a trip bus is through the EnerVista UR Setup software A protection summary
is displayed by navigating to a specific protection or control protection element and checking the desired bus box. Once the
desired element is selected for a specific bus, a list of element operate-type operands are displayed and can be assigned
to a trip bus. If more than one operate-type operand is required, it may be assigned directly from the trip bus menu.

5 SETTINGS 5.7 CONTROL ELEMENTS
Figure 5–131: TRIP BUS FIELDS IN THE PROTECTION SUMMARY

The following settings are available.
• TRIP BUS 1 BLOCK: The trip bus output is blocked when the operand assigned to this setting is asserted.
• TRIP BUS 1 PICKUP DELAY: This setting specifies a time delay to produce an output depending on how output is
used.
• TRIP BUS 1 RESET DELAY: This setting specifies a time delay to reset an output command. The time delay should be 5
set long enough to allow the breaker or contactor to perform a required action.
• TRIP BUS 1 INPUT 1 to TRIP BUS 1 INPUT 16: These settings select a FlexLogic operand to be assigned as an input
to the trip bus.
• TRIP BUS 1 LATCHING: This setting enables or disables latching of the trip bus output. This is typically used when
lockout is required or user acknowledgement of the relay response is required.
• TRIP BUS 1 RESET: The trip bus output is reset when the operand assigned to this setting is asserted. Note that the
RESET OP operand is pre-wired to the reset gate of the latch, As such, a reset command the front panel interface or via
communications will reset the trip bus output.
SETTINGS
TRIP BUS 1 INPUT 1
SETTINGS
= Off
TRIP BUS 1 PICKUP
TRIP BUS 1 INPUT 2
DELAY
= Off Non-volatile,
TRIP BUS 1 RESET
OR set-dominant
***
DELAY
AND S TPKP FLEXLOGIC OPERAND
TRIP BUS 1 INPUT 16 TRIP BUS 1 OP
Latch
= Off TRST
R
SETTINGS
TRIP BUS 1 FLEXLOGIC OPERAND
FUNCTION
TRIP BUS 1 PKP
= Enabled
TRIP BUS 1 BLOCK AND
= Off
SETTINGS
TRIP BUS 1
LATCHING
= Enabled
TRIP BUS 1 RESET
= Off
OR
FLEXLOGIC OPERAND
RESET OP 842023A1.CDR
Figure 5–132: TRIP BUS LOGIC

5.7.3 SETTING GROUPS
PATH: SETTINGS  CONTROL ELEMENTS  SETTINGS GROUPS
 SETTING GROUPS SETTING GROUPS Range: Disabled, Enabled

 FUNCTION: Enabled
SETTING GROUPS BLK: Range: FlexLogic operand
MESSAGE
Off
GROUP 2 ACTIVATE ON: Range: FlexLogic operand
MESSAGE
Off
MESSAGE
Off

MESSAGE
Off
GROUP 1 NAME: Range: up to 16 alphanumeric characters
MESSAGE

MESSAGE
5 MESSAGE
SETTING GROUP Range: Disabled, Enabled

MESSAGE
EVENTS: Disabled
The 61850 standard provides for the ability to monitor, edit, and change setting groups in a relay through a series of ser-
vices operating on Setting Group Control Block values. There is one SGCB in LLN0 in LD1 in the UR as, at present, the
other LDs do not support multiple setting groups The default value of SETTING GROUPS is Disabled. In order for 61850 and/
or UR setting group control to function, the SETTING GROUPS FUNCTION must be set to Enabled.
The active setting group in the UR is settable from either the value set via a FlexLogic operand in the UR (present practice)
or a SelectActiveSG command from a 61850 Client. For both the UR and IEC 61850, the default active setting group is "1".
A 61850 SelectActiveSG command sets one of the internal Non-Volatile flags (61850 SG Level x) that represents the
requested Active Setting Group shown as follows:
Table 5–31: ACTIVE SETTING GROUP
SELECTACTIVESG VALUE FLAG SET
1 (default) SG Level 1
2 SG Level 2
3 SG Level 3
4 SG Level 4
5 SG Level 4
6 SG Level 6
On power-up or restart, the previously selected 61850 SG Level x is re-instated. Similarly, the input to the setting group
control in the UR can be designed with Non-Volatile latches to achieve the same effect.
The setting groups menu controls the activation and deactivation of up to six possible groups of settings in the GROUPED
ELEMENTS settings menu. The faceplate Settings In Use LEDs indicate which active group (with a non-flashing energized
LED) is in service.

The SETTING GROUPS BLK setting prevents the active setting group from changing when the FlexLogic parameter is set to
"On". This can be useful in applications where it is undesirable to change the settings under certain conditions, such as the
breaker being open.
The GROUP 2 ACTIVATE ON to GROUP 6 ACTIVATE ON settings select a FlexLogic operand which, when set, makes the partic-
ular setting group active for use by any grouped element. A priority scheme ensures that only one group is active at a given
time – the highest-numbered group that is activated by its ACTIVATE ON parameter takes priority over the lower-numbered
groups. There is no activate on setting for group 1 (the default active group), because group 1 automatically becomes
active if no other group is active.
The SETTING GROUP 1 NAME to SETTING GROUP 6 NAME settings allows the user to assign a name to each of the six settings
groups. Once programmed, this name appears on the second line of the GROUPED ELEMENTS  SETTING GROUP 1(6) menu
display.
The relay can be set up via a FlexLogic equation to receive requests to activate or de-activate a particular non-default set-
tings group. The following FlexLogic equation (see the following figure) illustrates requests via remote communications (for
example, VIRTUAL INPUT 1 ON) or from a local contact input (for example, CONTACT IP 1 ON) to initiate the use of a particu-
lar settings group, and requests from several overcurrent pickup measuring elements to inhibit the use of the particular set-
tings group. The assigned VIRTUAL OUTPUT 1 operand is used to control the “On” state of a particular settings group.
1 VIRT IP 1 ON (VI1)
OR (2)
2 CONT IP 1 ON (H5A)
3 OR (2)
AND (3) = VIRT OP 1 (VO1)
4 PHASE TOC1 PKP
5 NOT
6 PHASE TOC2 PKP 5

7 NOT
8 AND (3)
9 = VIRT OP 1 (VO1)
10 END
842789A1.CDR
Figure 5–133: EXAMPLE FLEXLOGIC CONTROL OF A SETTINGS GROUP

5.7.4 SELECTOR SWITCH
PATH: SETTINGS  CONTROL ELEMENTS  SELECTOR SWITCH  SELECTOR SWITCH 1(2)
 SELECTOR SWITCH 1 SELECTOR 1 FUNCTION: Range: Disabled, Enabled

 Disabled
SELECTOR 1 FULL Range: 1 to 7 in steps of 1
MESSAGE
RANGE: 7
SELECTOR 1 TIME-OUT: Range: 3.0 to 60.0 s in steps of 0.1
MESSAGE
5.0 s
SELECTOR 1 STEP-UP: Range: FlexLogic operand
MESSAGE
Off
SELECTOR 1 STEP-UP Range: Time-out, Acknowledge
MESSAGE
MODE: Time-out
SELECTOR 1 ACK: Range: FlexLogic operand
MESSAGE
Off
SELECTOR 1 3BIT A0: Range: FlexLogic operand
MESSAGE
Off
MESSAGE
Off
5 MESSAGE
Off
SELECTOR 1 3BIT Range: Time-out, Acknowledge
MESSAGE
MODE: Time-out
SELECTOR 1 3BIT ACK: Range: FlexLogic operand
MESSAGE
Off
SELECTOR 1 POWER-UP Range: Restore, Synchronize, Sync/Restore
MESSAGE
MODE: Restore
SELECTOR 1 TARGETS: Range: Self-reset, Latched, Disabled
MESSAGE
Self-reset
SELECTOR 1 EVENTS: Range: Disabled, Enabled
MESSAGE
Disabled
The selector switch element is intended to replace a mechanical selector switch. Typical applications include setting group
control or control of multiple logic sub-circuits in user-programmable logic.
The element provides for two control inputs. The step-up control allows stepping through selector position one step at a
time with each pulse of the control input, such as a user-programmable pushbutton. The three-bit control input allows set-
ting the selector to the position defined by a three-bit word.
The element allows pre-selecting a new position without applying it. The pre-selected position gets applied either after time-
out or upon acknowledgement via separate inputs (user setting). The selector position is stored in non-volatile memory.
Upon power-up, either the previous position is restored or the relay synchronizes to the current three-bit word (user set-
ting). Basic alarm functionality alerts the user under abnormal conditions; for example, the three-bit control input being out
of range.
• SELECTOR 1 FULL RANGE: This setting defines the upper position of the selector. When stepping up through avail-
able positions of the selector, the upper position wraps up to the lower position (position 1). When using a direct three-
bit control word for programming the selector to a desired position, the change would take place only if the control word
is within the range of 1 to the SELECTOR FULL RANGE. If the control word is outside the range, an alarm is established
by setting the SELECTOR ALARM FlexLogic operand for 3 seconds.

• SELECTOR 1 TIME-OUT: This setting defines the time-out period for the selector. This value is used by the relay in
the following two ways. When the SELECTOR STEP-UP MODE is “Time-out”, the setting specifies the required period of
inactivity of the control input after which the pre-selected position is automatically applied. When the SELECTOR STEP-
UP MODE is “Acknowledge”, the setting specifies the period of time for the acknowledging input to appear. The timer is
re-started by any activity of the control input. The acknowledging input must come before the SELECTOR 1 TIME-OUT
timer expires; otherwise, the change will not take place and an alarm will be set.
• SELECTOR 1 STEP-UP: This setting specifies a control input for the selector switch. The switch is shifted to a new
position at each rising edge of this signal. The position changes incrementally, wrapping up from the last (SELECTOR 1
FULL RANGE) to the first (position 1). Consecutive pulses of this control operand must not occur faster than every
50 ms. After each rising edge of the assigned operand, the time-out timer is restarted and the SELECTOR SWITCH 1:
POS Z CHNG INITIATED target message is displayed, where Z the pre-selected position. The message is displayed for
the time specified by the FLASH MESSAGE TIME setting. The pre-selected position is applied after the selector times out
(“Time-out” mode), or when the acknowledging signal appears before the element times out (“Acknowledge” mode).
When the new position is applied, the relay displays the SELECTOR SWITCH 1: POSITION Z IN USE message. Typically,
a user-programmable pushbutton is configured as the stepping up control input.
• SELECTOR 1 STEP-UP MODE: This setting defines the selector mode of operation. When set to “Time-out”, the
selector will change its position after a pre-defined period of inactivity at the control input. The change is automatic and
does not require any explicit confirmation of the intent to change the selector's position. When set to “Acknowledge”,
the selector will change its position only after the intent is confirmed through a separate acknowledging signal. If the
acknowledging signal does not appear within a pre-defined period of time, the selector does not accept the change
and an alarm is established by setting the SELECTOR STP ALARM output FlexLogic operand for 3 seconds.
• SELECTOR 1 ACK: This setting specifies an acknowledging input for the stepping up control input. The pre-selected
position is applied on the rising edge of the assigned operand. This setting is active only under “Acknowledge” mode of
operation. The acknowledging signal must appear within the time defined by the SELECTOR 1 TIME-OUT setting after the
last activity of the control input. A user-programmable pushbutton is typically configured as the acknowledging input.
5
• SELECTOR 1 3BIT A0, A1, and A2: These settings specify a three-bit control input of the selector. The three-bit con-
trol word pre-selects the position using the following encoding convention:
A2 A1 A0 POSITION
0 0 0 rest
0 0 1 1
0 1 0 2
0 1 1 3
1 0 0 4
1 0 1 5
1 1 0 6
1 1 1 7
The “rest” position (0, 0, 0) does not generate an action and is intended for situations when the device generating the
three-bit control word is having a problem. When SELECTOR 1 3BIT MODE is “Time-out”, the pre-selected position is
applied in SELECTOR 1 TIME-OUT seconds after the last activity of the three-bit input. When SELECTOR 1 3BIT MODE is
“Acknowledge”, the pre-selected position is applied on the rising edge of the SELECTOR 1 3BIT ACK acknowledging
input.
The stepping up control input (SELECTOR 1 STEP-UP) and the three-bit control inputs (SELECTOR 1 3BIT A0 through A2)
lock-out mutually: once the stepping up sequence is initiated, the three-bit control input is inactive; once the three-bit
control sequence is initiated, the stepping up input is inactive.
• SELECTOR 1 3BIT MODE: This setting defines the selector mode of operation. When set to “Time-out”, the selector
changes its position after a pre-defined period of inactivity at the control input. The change is automatic and does not
require explicit confirmation to change the selector position. When set to “Acknowledge”, the selector changes its posi-
tion only after confirmation via a separate acknowledging signal. If the acknowledging signal does not appear within a
pre-defined period of time, the selector rejects the change and an alarm established by invoking the SELECTOR BIT
ALARM FlexLogic operand for 3 seconds.
• SELECTOR 1 3BIT ACK: This setting specifies an acknowledging input for the three-bit control input. The pre-
selected position is applied on the rising edge of the assigned FlexLogic operand. This setting is active only under the

“Acknowledge” mode of operation. The acknowledging signal must appear within the time defined by the SELECTOR
TIME-OUT setting after the last activity of the three-bit control inputs. Note that the stepping up control input and three-
bit control input have independent acknowledging signals (SELECTOR 1 ACK and SELECTOR 1 3BIT ACK, accordingly).
• SELECTOR 1 POWER-UP MODE: This setting specifies the element behavior on power up of the relay.
When set to “Restore”, the last position of the selector (stored in the non-volatile memory) is restored after powering up
the relay. If the position restored from memory is out of range, position 0 (no output operand selected) is applied and
an alarm is set (SELECTOR 1 PWR ALARM).
When set to “Synchronize” selector switch acts as follows. For two power cycles, the selector applies position 0 to the
switch and activates SELECTOR 1 PWR ALARM. After two power cycles expire, the selector synchronizes to the position
dictated by the three-bit control input. This operation does not wait for time-out or the acknowledging input. When the
synchronization attempt is unsuccessful (that is, the three-bit input is not available (0,0,0) or out of range) then the
selector switch output is set to position 0 (no output operand selected) and an alarm is established (SELECTOR 1 PWR
ALARM).
The operation of “Synch/Restore” mode is similar to the “Synchronize” mode. The only difference is that after an
unsuccessful synchronization attempt, the switch will attempt to restore the position stored in the relay memory. The
“Synch/Restore” mode is useful for applications where the selector switch is employed to change the setting group in
redundant (two relay) protection schemes.
• SELECTOR 1 EVENTS: If enabled, the following events are logged:
EVENT NAME DESCRIPTION

SELECTOR 1 POS Z Selector 1 changed its position to Z.
SELECTOR 1 STP ALARM The selector position pre-selected via the stepping up control input has not been
confirmed before the time out.
5 SELECTOR 1 BIT ALARM The selector position pre-selected via the three-bit control input has not been confirmed
before the time out.

The following figures illustrate the operation of the selector switch. In these diagrams, “T” represents a time-out setting.
pre-existing changed to 4 with changed to 1 with changed to 2 with a changed to 7 with

position 2 a pushbutton a 3-bit input pushbutton a 3-bit input
STEP-UP
T T
3BIT A0
3BIT A1
3BIT A2
T T
POS 1
POS 2
POS 3
POS 4
POS 5
POS 6 5
POS 7
BIT 0
BIT 1
BIT 2
STP ALARM
BIT ALARM
ALARM
842737A1.CDR
Figure 5–134: TIME-OUT MODE

pre-existing changed to 4 with changed to 1 with changed to 2 with

position 2 a pushbutton a 3-bit input a pushbutton
STEP-UP
ACK
3BIT A0
3BIT A1
3BIT A2
3BIT ACK
POS 1
POS 2
POS 3
POS 4
POS 5
POS 6
5 POS 7
BIT 0
BIT 1
BIT 2
STP ALARM
BIT ALARM
ALARM
842736A1.CDR
Figure 5–135: ACKNOWLEDGE MODE

APPLICATION EXAMPLE
Consider an application where the selector switch is used to control setting groups 1 through 4 in the relay. The setting
groups are to be controlled from both user-programmable pushbutton 1 and from an external device via contact inputs 1
through 3. The active setting group shall be available as an encoded three-bit word to the external device and SCADA via
output contacts 1 through 3. The pre-selected setting group shall be applied automatically after 5 seconds of inactivity of
the control inputs. When the relay powers up, it should synchronize the setting group to the three-bit control input.
Make the following changes to setting group control in the SETTINGS  CONTROL ELEMENTS  SETTING GROUPS menu:
SETTING GROUPS FUNCTION: “Enabled” GROUP 4 ACTIVATE ON: “SELECTOR 1 POS 4"
SETTING GROUPS BLK: “Off” GROUP 5 ACTIVATE ON: “Off”
GROUP 2 ACTIVATE ON: “SELECTOR 1 POS 2" GROUP 6 ACTIVATE ON: “Off”
GROUP 3 ACTIVATE ON: “SELECTOR 1 POS 3"
Make the following changes to selector switch element in the SETTINGS  CONTROL ELEMENTS  SELECTOR SWITCH 
SELECTOR SWITCH 1 menu to assign control to user programmable pushbutton 1 and contact inputs 1 through 3:

SELECTOR 1 FUNCTION: “Enabled” SELECTOR 1 3BIT A0: “CONT IP 1 ON”

SELECTOR 1 FULL-RANGE: “4” SELECTOR 1 3BIT A1: “CONT IP 2 ON”
SELECTOR 1 STEP-UP MODE: “Time-out” SELECTOR 1 3BIT A2: “CONT IP 3 ON”
SELECTOR 1 TIME-OUT: “5.0 s” SELECTOR 1 3BIT MODE: “Time-out”
SELECTOR 1 STEP-UP: “PUSHBUTTON 1 ON” SELECTOR 1 3BIT ACK: “Off”
SELECTOR 1 ACK: “Off” SELECTOR 1 POWER-UP MODE: “Synchronize”
Now, assign the contact output operation (assume the H6E module) to the selector switch element by making the following
changes in the SETTINGS  INPUTS/OUTPUTS  CONTACT OUTPUTS menu:
OUTPUT H1 OPERATE: “SELECTOR 1 BIT 0"
Finally, assign configure user-programmable pushbutton 1 by making the following changes in the SETTINGS  PRODUCT
SETUP  USER-PROGRAMMABLE PUSHBUTTONS  USER PUSHBUTTON 1 menu:

PUSHBUTTON 1 DROP-OUT TIME: “0.10 s”
The logic for the selector switch is shown below:
SETTINGS
SELECTOR 1 FULL RANGE:
SELECTOR 1 STEP-UP MODE:
SELECTOR 1 3BIT MODE:
SELECTOR 1 TIME-OUT: ACTUAL VALUE

SETTINGS
SELECTOR 1 POSITION
5
SELECTOR 1 FUNCTION: SELECTOR 1 POWER-UP MODE:
Enabled = 1 RUN
SELECTOR 1 STEP-UP: FLEXLOGIC™ OPERANDS
Off = 0 step up SELECTOR 1 POS 1
2
SELECTOR 1 ACK: 1 SELECTOR 1 POS 2
3
Off = 0 acknowledge SELECTOR 1 POS 3
SELECTOR 1 3BIT A0: 4
SELECTOR 1 POS 4
three-bit control input
Off = 0 SELECTOR 1 POS 5

ON
SELECTOR 1 3BIT A1: 7 5
SELECTOR 1 POS 6
Off = 0 6
SELECTOR 1 POS 7
SELECTOR 1 3BIT A2:
Off = 0 FLEXLOGIC™ OPERANDS
SELECTOR 1 3BIT ACK:
SELECTOR 1 STP ALARM
Off = 0 3-bit acknowledge
SELECTOR 1 BIT ALARM
3-bit position out
OR
SELECTOR 1 ALARM
SELECTOR 1 PWR ALARM
SELECTOR 1 BIT 0
SELECTOR 1 BIT 1
SELECTOR 1 BIT 2
842012A2.CDR
Figure 5–136: SELECTOR SWITCH LOGIC

5.7.5 TRIP OUTPUT
PATH: SETTINGS  CONTROL ELEMENTS  TRIP OUTPUT
 TRIP OUTPUT TRIP MODE: Range: Disabled, 3 Pole Only, 3 Pole & 1 Pole
 Disabled
TRIP 3-POLE INPUT-1: Range: FlexLogic operand
MESSAGE
Off
MESSAGE
Off

MESSAGE
Off
MESSAGE
Off
MESSAGE
Off

MESSAGE
Off
5 MESSAGE
TRIP RECLOSE INPUT-1:
Off
TRIP RECLOSE INPUT-2: Range: FlexLogic operand

MESSAGE
Off

TRIP RECLOSE INPUT-6: Range: FlexLogic operand
MESSAGE
Off
TRIP SEAL-IN DELAY: Range: 0 to 65.535 s in steps of 0.001
MESSAGE
0.000 s
TRIP RESET: Range: Pole Curr OR Custom, CBaux OR Custom,
MESSAGE Custom
CBaux OR Custom
START TMR Z2PH Inp1: Range: FlexLogic operand
MESSAGE
Off
START TMR Z2PH Inp2: Range: FlexLogic operand
MESSAGE
Off
START TMR Z2GR Inp1: Range: FlexLogic operand
MESSAGE
Off
START TMR Z2GR Inp2: Range: FlexLogic operand
MESSAGE
Off
BKR ΦA OPEN: Range: FlexLogic operand
MESSAGE
Off
BKR ΦB OPEN: Range: FlexLogic operand
MESSAGE
Off
BKR ΦC OPEN: Range: FlexLogic operand
MESSAGE
Off

TRIP FORCE 3-POLE: Range: FlexLogic operand

MESSAGE
Off
TRIP PILOT PRIORITY: Range: 0 to 65.535 s in steps of 0.001
MESSAGE
0.000 s
REVERSE FAULT: Range: FlexLogic operand
MESSAGE
Off
TRIP DELAY ON EVOLV Range: 0 to 65.535 s in steps of 0.001
MESSAGE
FAULTS: 0.000 s
TRIP EVENTS: Range: Enabled, Disabled
MESSAGE
Disabled
The trip output element is primarily used to collect trip requests from protection elements and other inputs to generate out-
put operands to initiate trip operations. Three pole trips will only initiate reclosure if programmed to do so, whereas single
pole trips will always automatically initiate reclosure. The TRIP 3-POLE and TRIP 1-POLE output operands can also be used
as inputs to a FlexLogic OR gate to operate the faceplate Trip indicator LED.
THREE POLE OPERATION:
In applications where single-pole tripping is not required this element provides a convenient method of collecting inputs to
initiate tripping of circuit breakers, the reclose element and breaker failure elements.
SINGLE POLE OPERATION:
This element must be used in single pole operation applications.
5
NOTE
In these applications this element is used to:

• Determine if a single pole operation should be performed.
• Collect inputs to initiate three pole tripping, the recloser and breaker failure elements.
• Collect inputs to initiate single pole tripping, the recloser and breaker failure elements.
• Assign a higher priority to pilot aided scheme outputs than to exclusively local inputs.
The trip output element works in association with other D60 elements (refer to the Theory of operation chapter for a com-
plete description of single-pole operations) that must be programmed and in-service for successful operation. The neces-
sary elements are: recloser, breaker control, open pole detector, and phase selector. The recloser must also be in the
“Reset” state before a single pole trip can be issued. Outputs from this element are also directly connected as initiate sig-
nals to the breaker failure elements.
At least one internal protection element or digital input representing detection of a fault must be available as an input to this
element. In pilot-aided scheme applications, a timer can be used to delay the output decision until data from a remote ter-
minal is received from communications facilities, to prevent a three pole operation where a single pole operation is permit-
ted.
To ensure correct operation of the single-pole tripping feature, any non-distance protection used for single pole trip-
ping (such as high-set overcurrent using the instantaneous or directional overcurrent elements) must be blocked by
NOTE the OPEN POLE OP ΦA, OPEN POLE OP ΦB, or OPEN POLE OP ΦC operands. For example, instantaneous overcur-
rent phase A will be blocked by OPEN POLE OP ΦA operand. This blocking condition is pre-wired for distance pro-
tection.
The following settings are available for the trip output element.
• TRIP MODE: This setting is used to select the required mode of operation. If selected to “3 Pole Only” outputs for all
three phases are always set simultaneously. If selected to “3 Pole & 1 Pole” outputs for all three phases are set simul-
taneously unless the phase selector or a pilot aided scheme determines the fault is single-phase-to-ground. If the fault
is identified as being AG, BG or CG only the operands for the faulted phase will be asserted.
• TRIP 3-POLE INPUT-1 to TRIP 3-POLE INPUT-6: These settings are used to select an operand representing a fault
condition that is not desired to initiate a single pole operation (for example, phase undervoltage). Use a FlexLogic OR-
gate if more than six inputs are required.

• TRIP 1-POLE INPUT-1 to TRIP 1-POLE INPUT-6: These settings are used to select an operand representing a fault
condition that is desired to initiate a single pole trip-and-reclose if the fault is single phase to ground (for example, dis-
tance zone 1). Use a FlexLogic OR-gate if more than six inputs are required. The inputs do not have to be phase-spe-
cific as the phase selector determines the fault type.
The AR FORCE 3-P TRIP operand is asserted by the autorecloser 1.5 cycles after single-pole reclosing is initiated. This
operand calls for a three-pole trip if any protection element configured under TRIP 1-POLE INPUT remains picked-up. The
open pole detector provides blocking inputs to distance elements, and therefore the latter will reset immediately after
the TRIP 1-POLE operand is asserted. For other protection elements used in single-pole tripping, the user must ensure
they will reset immediately after tripping, otherwise the fact that they are still picked up will be detected as an evolving
fault and the relay will trip three-poles. For example, if high-set phase instantaneous overcurrent is used (TRIP 1-POLE
INPUT X: “PHASE IOC1 OP”), then OPEN POLE OP A shall be used for blocking phase A of the instantaneous overcur-
rent element. In this way, after tripping phase A, the phase a instantaneous overcurrent element is forced to reset.
Phases B and C are still operational and can detect an evolving fault as soon as 8 ms after tripping phase A. Neutral
and negative-sequence instantaneous overcurrent elements shall be blocked from the OPEN POLE BLK N operand
unless the pickup setting is high enough to prevent pickup during single-pole reclosing.
• TRIP RECLOSE INPUT-1 to TRIP RECLOSE INPUT-6: These settings select an operand representing a fault condi-
tion that is desired to initiate three pole reclosing (for example, phase distance zone 1). Use a FlexLogic OR-gate if
more than six inputs are required. These inputs also include the TRIP 1-POLE INPUT-1 to TRIP 1-POLE INPUT-6 values,
which are intended to initiate three-pole reclosing in situations where single-pole tripping commands are changed to
three-pole tripping commands. This can happen in cases where the phase selector identifies a multi-phase fault or the
AR FORCE 3P TRIP command is present.
• TRIP SEAL-IN DELAY: This setting specifies the minimum time that trip command signals are maintained to provide
sufficient time to open the breaker poles. If a value of “0” is specified, then the output signal is reset once the protection
elements initiating the trip are reset. If a value other than “0” is specified, then the protection elements must reset and
5 •
the timer initiated at the first trip command must expire.
TRIP RESET: This setting selects the option to reset the trip latches. If “Pole Curr OR Custom” is chosen, then the
OPEN POLE CURRENT PKP setting should be programmed accordingly. If “CBaux OR Custom” is chosen, then the break-
ers should be set appropriately. Both the “Current” and “CBaux” options can be complimented by custom conditions
using the BKR ΦA OPEN, BKR ΦB OPEN, and BKR ΦC OPEN settings indicated below. Alternately, a purely custom condi-
tion can be applied to reset trip output latches.
• START TMR Z2PH Inp1 and START TMR Z2PH Inp2: These settings select an operand that will start the phase dis-
tance zone 2 timer to avoid a trip delay if the fault evolves from one type to another type (for example, from a single-
line–to-ground fault to a multi-phase fault) or from one zone of protection to another zone of protection (for example,
from zone 3 to zone 2). For instance, the GND DIST Z2 PKP FlexLogic operand or the PH DIST Z3 PKP FlexLogic oper-
and could be assigned to either of these settings. Use a FlexLogic OR-gate if more than two inputs are required. Refer
to phase distance logic diagrams for additional information.
• START TMR Z2GR Inp1 and START TMR Z2GR Inp2: These settings select an operand that will start the ground dis-
tance zone 2 timer to avoid a trip delay if the fault evolves from one zone of protection to another zone of protection (for
example, from zone 3 to zone 2). For instance, the GND DIST Z3 PKP FlexLogic operand could be assigned to these
settings. Use a FlexLogic OR-gate if more than two inputs are required. Refer to ground distance logic diagrams for
additional information.
• BKR ΦA OPEN, BKR ΦB OPEN, and BKR ΦC OPEN: This settings are used to select an operand to indicates that
phase A, B, or C of the breaker is open, respectively.
• TRIP FORCE 3-POLE: Selects an operand that will force an input selected for single pole operation to produce a three
pole operation. The AR DISABLED FlexLogic operand is the recommended value for this setting. Power system config-
urations or conditions which require such operations may be considered as well.
• TRIP PILOT PRIORITY: This setting is used to set an interval equal to the inter-relay channel communications time,
plus an appropriate margin, during which outputs are not asserted. This delay permits fault identification information
from a remote terminal to be used instead of local data only.
• REVERSE FAULT: This setting should be used to guarantee accuracy of single-pole tripping under evolving external to
internal faults. When a close-in external fault occurs, the relay is biased toward very fast operation on a following inter-
nal fault. This is primarily due to depressed voltages and elevated currents in response to the first, external fault. The
phase selector can exhibit some time lag compared to the main protection elements. This can potentially result in a

spurious three-pole operation on a single-line-to-ground internal fault. Delaying tripping on internal faults that follow
detection of reverse faults solves the problem.
As long as the operand indicated under this setting is asserted the trip action is delayed by TRIP DELAY ON EVOLV
FAULTS time. Typically this operand should combine reverse zone indications (such as zone 4 pickup) with a half-cycle
pickup delay, and two-cycle dropout delay. This setting should be used only in single-pole tripping applications, when
evolving faults are of importance, and slightly delayed operation on evolving faults could be traded for enhanced accu-
racy of single-pole tripping.
• TRIP DELAY ON EVOLV FAULTS: Use this setting in conjunction with the REVERSE FAULT setting (see above). Typi-
cally this value is set around half a power system cycle. Use it only in single-pole tripping applications, when evolving
faults are of importance, and slightly delayed operation on evolving faults could be traded for enhanced accuracy of
single-pole tripping.

Figure 5–137: TRIP OUTPUT SCHEME LOGIC (Sheet 1 of 2)

6(77,1*
7ULS'HOD\RQ(YROYLQJ)DXOWV
)URPWULSRXWSXWORJLFVKHHW$*
3+$6($ 6
25 )/(;/2*,&23(5$1'
3+$6(%
/DWFK 75,33+$6($
3+$6(&
$1' 5
6(77,1*

6(77,1* 25 6 )/(;/2*,&23(5$1'
5HYHUVH)DXOW
$1' /DWFK 75,33+$6(%
2II
5
6(77,1*

25 6 )/(;/2*,&23(5$1'
/DWFK 75,33+$6(&
)URPWULSRXWSXWORJLF $1'
5
VKHHW$*
3 6 )/(;/2*,&23(5$1'
/DWFK 75,332/(
25 5 25 75,328738723
$1'
6(77,1*
)/(;/2*,&23(5$1'
7ULS6HDO,Q'HOD\ $1'
$1' 75,332/(
;25
25
$1'
7,0(5
)/(;/2*,&23(5$1'
5

$1' 75,3$5,1,732/(
6(77,1* PV
)/(;/2*,&23(5$1'6 7ULS5HVHW
23(132/(,Ů$
25
23(132/(%.5Ů$23
3ROH&XUU25&XVWRP
6(77,1*
&%DX[25&XVWRP $1'
%NU3KDVH$2SHQ 25
2II
&XVWRP
)/(;/2*,&23(5$1'6
23(132/(,Ů%
25
23(132/(%.5Ů%23
3ROH&XUU25&XVWRP
6(77,1*
$1'
%NU3KDVH%2SHQ &%DX[25&XVWRP
25
2II
&XVWRP
)/(;/2*,&23(5$1'6
23(132/(,Ů%
25
23(132/(%.5Ů%23
3ROH&XUU25&XVWRP
6(77,1*
$1'
%NU3KDVH%2SHQ &%DX[25&XVWRP
25
2II
&XVWRP
6(77,1*
7ULS5HFORVH,QSXW
2II
6(77,1* 25
7ULS5HFORVH,QSXW
2II
6(77,1*6
6WDUW7LPHU=3K,Q
2II WRSKDVHGLVWDQFH]RQHORJLF
6WDUW7LPHU=3K,Q 25 )/(;/2*,&23(5$1'
2II $1' 75,3=3+705,1,7
6WDUW7LPHU=*U,Q
WRJURXQGGLVWDQFH]RQHORJLF
2II
)/(;/2*,&23(5$1'
6WDUW7LPHU=*U,Q 25
$1' 75,3=*5705,1,7
2II
)URPWULSRXWSXW
ORJLFVKHHW (1$%/('
$* $&'5
Figure 5–138: TRIP OUTPUT SCHEME LOGIC (Sheet 2 of 2)

5.7.6 UNDERFREQUENCY
PATH: SETTINGS  CONTROL ELEMENTS  UNDERFREQUENCY  UNDERFREQUENCY 1(6)
 UNDERFREQUENCY 1 UNDFREQ 1 FUNCTION: Range: Disabled, Enabled

 Disabled
UNDERFREQ 1 BLOCK: Range: FlexLogic operand
MESSAGE
Off
UNDERFREQ 1 SOURCE: Range: SRC 1, SRC 2, SRC 3, SRC 4
MESSAGE
SRC 1
UNDERFREQ 1 MIN Range: 0.10 to 1.25 pu in steps of 0.01
MESSAGE
VOLT/AMP: 0.10 pu
UNDERFREQ 1 PICKUP: Range: 20.00 to 65.00 Hz in steps of 0.01
MESSAGE
59.50 Hz
UNDERFREQ 1 PICKUP Range: 0.000 to 65.535 s in steps of 0.001
MESSAGE
DELAY: 2.000 s
UNDERFREQ 1 RESET Range: 0.000 to 65.535 s in steps of 0.001
MESSAGE
DELAY : 2.000 s
UNDERFREQ 1 TARGET: Range: Self-reset, Latched, Disabled
MESSAGE
Self-reset
UNDERFREQ 1 EVENTS: Range: Disabled, Enabled
5 MESSAGE
Disabled
There are six identical underfrequency elements, numbered from 1 through 6.

The steady-state frequency of a power system is a certain indicator of the existing balance between the generated power
and the load. Whenever this balance is disrupted through the loss of an important generating unit or the isolation of part of
the system from the rest of the system, the effect will be a reduction in frequency. If the control systems of the system gen-
erators do not respond fast enough, the system may collapse. A reliable method to quickly restore the balance between
load and generation is to automatically disconnect selected loads, based on the actual system frequency. This technique,
called “load-shedding”, maintains system integrity and minimize widespread outages. After the frequency returns to normal,
the load may be automatically or manually restored.
The UNDERFREQ 1 SOURCE setting is used to select the source for the signal to be measured. The element first checks for a
live phase voltage available from the selected source. If voltage is not available, the element attempts to use a phase cur-
rent. If neither voltage nor current is available, the element will not operate, as it will not measure a parameter below the
minimum voltage/current setting.
The UNDERFREQ 1 MIN VOLT/AMP setting selects the minimum per unit voltage or current level required to allow the underfre-
quency element to operate. This threshold is used to prevent an incorrect operation because there is no signal to measure.
This UNDERFREQ 1 PICKUP setting is used to select the level at which the underfrequency element is to pickup. For example,
if the system frequency is 60 Hz and the load shedding is required at 59.5 Hz, the setting will be 59.50 Hz.
SETTING
UNDERFREQ 1 FUNCTION:
Enabled=1
SETTING SETTING SETTING

UNDERFREQ 1 UNDERFREQ 1
UNDERFREQ 1 BLOCK: PICKUP : PICKUP DELAY :
AND RUN FLEXLOGIC OPERANDS
Off = 0 UNDERFREQ 1
UNDERFREQ 1 PKP
RESET DELAY :
SETTING UNDERFREQ 1 DPO
SETTING tPKP
UNDERFREQ 1 0 < f < PICKUP tRST UNDERFREQ 1 OP
UNDERFREQ 1 SOURCE: ACTUAL VALUES MIN VOLT / AMP:
Level < Min
VOLT / AMP 827079A9.CDR
Frequency
Figure 5–139: UNDERFREQUENCY SCHEME LOGIC

5.7.7 OVERFREQUENCY
PATH: SETTINGS  CONTROL ELEMENTS  OVERFREQUENCY  OVERFREQUENCY 1(4)
 OVERFREQUENCY 1 OVERFREQ 1 FUNCTION: Range: Disabled, Enabled

 Disabled
OVERFREQ 1 BLOCK: Range: FlexLogic operand
MESSAGE
Off
OVERFREQ 1 SOURCE: Range: SRC 1, SRC 2, SRC 3, SRC 4
MESSAGE
SRC 1
OVERFREQ 1 PICKUP: Range: 20.00 to 65.00 Hz in steps of 0.01
MESSAGE
60.50 Hz
OVERFREQ 1 PICKUP Range: 0.000 to 65.535 s in steps of 0.001
MESSAGE
DELAY: 0.500 s
OVERFREQ 1 RESET Range: 0.000 to 65.535 s in steps of 0.001
MESSAGE
DELAY : 0.500 s
OVERFREQ 1 TARGET: Range: Self-reset, Latched, Disabled
MESSAGE
Self-reset
OVERFREQ 1 EVENTS: Range: Disabled, Enabled
MESSAGE
Disabled
There are four overfrequency elements, numbered 1 through 4.

A frequency calculation for a given source is made on the input of a voltage or current channel, depending on which is
5
available. The channels are searched for the signal input in the following order: voltage channel A, auxiliary voltage chan-
nel, current channel A, ground current channel. The first available signal is used for frequency calculation.
The steady-state frequency of a power system is an indicator of the existing balance between the generated power and the
load. Whenever this balance is disrupted through the disconnection of significant load or the isolation of a part of the sys-
tem that has a surplus of generation, the effect will be an increase in frequency. If the control systems of the generators do
not respond fast enough, to quickly ramp the turbine speed back to normal, the overspeed can lead to the turbine trip. The
overfrequency element can be used to control the turbine frequency ramp down at a generating location. This element can
also be used for feeder reclosing as part of the "after load shedding restoration".
The OVERFREQ 1 SOURCE setting selects the source for the signal to be measured. The OVERFREQ 1 PICKUP setting selects
the level at which the overfrequency element is to pickup.
SETTING
OVERFREQ 1 FUNCTION:
SETTING
Enabled = 1
OVERFREQ 1 PICKUP : SETTING
SETTING OVERFREQ 1 PICKUP
AND RUN DELAY :
OVERFREQ 1 BLOCK: FLEXLOGIC OPERANDS
OVERFREQ 1 RESET
OVERFREQ 1 PKP
DELAY :
Off = 0 OVERFREQ 1 DPO
tPKP
tRST OVERFREQ 1 OP
SETTING f ≡ PICKUP
OVERFREQ 1 SOURCE:
Frequency 827832A6.CDR
Figure 5–140: OVERFREQUENCY SCHEME LOGIC

5.7.8 FREQUENCY RATE OF CHANGE
PATH: SETTINGS  CONTROL ELEMENTS  FREQUENCY RATE OF CHANGE  FREQUENCY RATE OF CHANGE 1(4)
 FREQUENCY RATE FREQ RATE 1 Range: Disabled, Enabled

 OF CHANGE 1 FUNCTION: Disabled
FREQ RATE 1 SOURCE: Range: SRC 1, SRC 2, SRC 3, SRC 4
MESSAGE
SRC 1
FREQ RATE 1 TREND: Range: Increasing, Decreasing, Bi-directional
MESSAGE
Increasing
FREQ RATE 1 PICKUP: Range: 0.10 to 15.00 Hz/sec in steps of 0.01
MESSAGE
0.50 Hz/sec
FREQ RATE 1 OV SUPV Range: 0.100 to 3.000 pu in steps of 0.001
MESSAGE
PICKUP: 0.700 pu
FREQ RATE 1 OC SUPV Range: 0.000 to 30.000 pu in steps of 0.001
MESSAGE
PICKUP: 0.200 pu
FREQ RATE 1 MIN Range: 20.00 to 80.00 Hz in steps of 0.01
MESSAGE
FREQUENCY: 45.00 Hz
FREQ RATE 1 MAX Range: 20.00 to 80.00 Hz in steps of 0.01
MESSAGE
FREQUENCY: 65.00 Hz
FREQ RATE 1 PICKUP Range: 0 to 65.535 s in steps of 0.001
5 MESSAGE
DELAY: 0.000 s
FREQ RATE 1 RESET Range: 0 to 65.535 s in steps of 0.001
MESSAGE
DELAY: 0.000 s
FREQ RATE 1 BLOCK: Range: FlexLogic operand
MESSAGE
Off
FREQ RATE 1 TARGET: Range: Self-Reset, Latched, Disabled
MESSAGE
Self-Reset
FREQ RATE 1 EVENTS: Range: Disabled, Enabled
MESSAGE
Disabled
Four independent rate of change of frequency elements are available. The element responds to rate of change of fre-
quency with voltage, current and frequency supervision.
• FREQ RATE 1 TREND: This setting allows configuring the element to respond to increasing or decreasing frequency,
or to frequency change in either direction.
• FREQ RATE 1 PICKUP: This setting specifies an intended df  dt pickup threshold. For applications monitoring a
decreasing trend, set FREQ RATE 1 TREND to “Decreasing” and specify the pickup threshold accordingly. The operating
condition is: – df  dt  Pickup .
For applications monitoring an increasing trend, set FREQ RATE 1 TREND to “Increasing” and specify the pickup thresh-
old accordingly. The operating condition is: df  dt  Pickup .
For applications monitoring rate of change of frequency in any direction set FREQ RATE 1 TREND to “Bi-Directional” and
specify the pickup threshold accordingly. The operating condition is: abs  df  dt   Pickup
• FREQ RATE 1 OV SUPV PICKUP: This setting defines minimum voltage level required for operation of the element.
The supervising function responds to the positive-sequence voltage. Overvoltage supervision should be used to pre-
vent operation under specific system conditions such as faults.
• FREQ RATE 1 OC SUPV PICKUP: This setting defines minimum current level required for operation of the element.
The supervising function responds to the positive-sequence current. Typical application includes load shedding. Set
the pickup threshold to zero if no overcurrent supervision is required.

• FREQ RATE 1 MIN FREQUENCY: This setting defines minimum frequency level required for operation of the element.
The setting may be used to effectively block the feature based on frequency. For example, if the intent is to monitor an
increasing trend but only if the frequency is already above certain level, this setting should be set to the required fre-
quency level.
• FREQ RATE 1 MAX FREQUENCY: This setting defines maximum frequency level required for operation of the ele-
ment. The setting may be used to effectively block the feature based on frequency. For example, if the intent is to mon-
itor a decreasing trend but only if the frequency is already below certain level (such as for load shedding), this setting
should be set to the required frequency level.
If the signal source assigned to the frequency rate of change element is only set to auxiliary VT, then the minimum
voltage supervision is 3 V.
NOTE
SETTINGS
SETTING
FREQ RATE 1 FUNCTION:
FREQ RATE 1 OV SUPV
Enabled = 1 PICKUP:
AND
FREQ RATE 1 BLOCK: RUN

Off
| V_1 | > PICKUP
SETTINGS
SETTING SETTINGS
FREQ RATE 1 PICKUP
DELAY:
SETTING FREQ RATE 1 OC SUPV FREQ RATE 1 TREND:
PICKUP: FREQ RATE 1 RESET
FREQ RATE 1 SOURCE: DELAY:
FREQ RATE 1 PICKUP:
RUN
tPKP FLEXLOGIC OPERANDS
AND
Pos seq voltage (V_1) RUN

Pos seq current (I_1) | I_1 | >PICKUP FREQ RATE 1 OP
Frequency (F) df/dt > PICKUP tRST
FREQ RATE 1 DPO
SETTINGS
FREQ RATE 1 PKP
FREQ RATE 1 MIN
FREQUENCY:
FREQ RATE 1 MAX

FREQUENCY:
5
RUN
F > MIN & F < MAX
RUN
Calculate df/dt
832023A2.CDR
Figure 5–141: FREQUENCY RATE OF CHANGE SCHEME LOGIC

5.7.9 SYNCHROCHECK
PATH: SETTINGS  CONTROL ELEMENTS  SYNCHROCHECK  SYNCHROCHECK 1(4)
 SYNCHROCHECK 1 SYNCHK1 FUNCTION: Range: Disabled, Enabled

 Disabled
SYNCHK1 BLOCK: Range: FlexLogic operand
MESSAGE
Off
SYNCHK1 V1 SOURCE: Range: SRC 1, SRC 2, SRC 3, SRC 4
MESSAGE
SRC 1
SYNCHK1 V2 SOURCE: Range: SRC 1, SRC 2, SRC 3, SRC 4
MESSAGE
SRC 2
SYNCHK1 MAX VOLT Range: 0 to 400000 V in steps of 1
MESSAGE
DIFF: 10000 V
SYNCHK1 MAX ANGLE Range: 0 to 100° in steps of 1
MESSAGE
DIFF: 30°
SYNCHK1 MAX FREQ Range: 0.00 to 2.00 Hz in steps of 0.01
MESSAGE
DIFF: 1.00 Hz
SYNCHK1 MAX FREQ Range: 0.00 to 0.10 Hz in steps of 0.01
MESSAGE
HYSTERESIS: 0.06 Hz
SYNCHK1 DEAD SOURCE Range: None, LV1 and DV2, DV1 and LV2, DV1 or DV2,
5 MESSAGE
SELECT: LV1 and DV2 DV1 Xor DV2, DV1 and DV2
SYNCHK1 DEAD V1 Range: 0.00 to 1.25 pu in steps of 0.01

MESSAGE
MAX VOLT: 0.30 pu
SYNCHK1 DEAD V2 Range: 0.00 to 1.25 pu in steps of 0.01
MESSAGE
MAX VOLT: 0.30 pu
SYNCHK1 LIVE V1 Range: 0.00 to 1.25 pu in steps of 0.01
MESSAGE
MIN VOLT: 0.70 pu
SYNCHK1 LIVE V2 Range: 0.00 to 1.25 pu in steps of 0.01
MESSAGE
MIN VOLT: 0.70 pu
SYNCHK1 TARGET: Range: Self-reset, Latched, Disabled
MESSAGE
Self-reset
SYNCHK1 EVENTS: Range: Disabled, Enabled
MESSAGE
Disabled
There are four identical synchrocheck elements available, numbered 1 to 4.

The synchronism check function is intended for supervising the paralleling of two parts of a system which are to be joined
by the closure of a circuit breaker. The synchrocheck elements are typically used at locations where the two parts of the
system are interconnected through at least one other point in the system.
Synchrocheck verifies that the voltages (V1 and V2) on the two sides of the supervised circuit breaker are within set limits
of magnitude, angle and frequency differences. The time that the two voltages remain within the admissible angle differ-
ence is determined by the setting of the phase angle difference  and the frequency difference F (slip frequency). It can
be defined as the time it would take the voltage phasor V1 or V2 to traverse an angle equal to 2   at a frequency equal
to the frequency difference F. This time can be calculated by:
1
T = -------------------------------- (EQ 5.26)
360
------------------  F
2  
where: = phase angle difference in degrees; F = frequency difference in Hz.

If one or both sources are de-energized, the synchrocheck programming can allow for closing of the circuit breaker using
undervoltage control to by-pass the synchrocheck measurements (dead source function).
• SYNCHK1 V1 SOURCE: This setting selects the source for voltage V1 (see NOTES below).
• SYNCHK1 V2 SOURCE: This setting selects the source for voltage V2, which must not be the same as used for the
V1 (see NOTES below).
• SYNCHK1 MAX VOLT DIFF: This setting selects the maximum primary voltage difference in volts between the two
sources. A primary voltage magnitude difference between the two input voltages below this value is within the permis-
sible limit for synchronism.
• SYNCHK1 MAX ANGLE DIFF: This setting selects the maximum angular difference in degrees between the two
sources. An angular difference between the two input voltage phasors below this value is within the permissible limit
for synchronism.
• SYNCHK1 MAX FREQ DIFF: This setting selects the maximum frequency difference in ‘Hz’ between the two sources.
A frequency difference between the two input voltage systems below this value is within the permissible limit for syn-
chronism.
• SYNCHK1 MAX FREQ HYSTERESIS: This setting specifies the required hysteresis for the maximum frequency differ-
ence condition. The condition becomes satisfied when the frequency difference becomes lower than SYNCHK1 MAX
FREQ DIFF. Once the Synchrocheck element has operated, the frequency difference must increase above the SYNCHK1
MAX FREQ DIFF + SYNCHK1 MAX FREQ HYSTERESIS sum to drop out (assuming the other two conditions, voltage and
angle, remain satisfied).
• SYNCHK1 DEAD SOURCE SELECT: This setting selects the combination of dead and live sources that will by-pass
synchronism check function and permit the breaker to be closed when one or both of the two voltages (V1 or/and V2)
are below the maximum voltage threshold. A dead or live source is declared by monitoring the voltage level. Six
options are available:
None: Dead Source function is disabled
5
LV1 and DV2: Live V1 and Dead V2
DV1 and LV2: Dead V1 and Live V2
DV1 or DV2: Dead V1 or Dead V2
DV1 Xor DV2: Dead V1 exclusive-or Dead V2 (one source is Dead and the other is Live)
DV1 and DV2: Dead V1 and Dead V2
• SYNCHK1 DEAD V1 MAX VOLT: This setting establishes a maximum voltage magnitude for V1 in 1 ‘pu’. Below this
magnitude, the V1 voltage input used for synchrocheck will be considered “Dead” or de-energized.
• SYNCHK1 DEAD V2 MAX VOLT: This setting establishes a maximum voltage magnitude for V2 in ‘pu’. Below this
magnitude, the V2 voltage input used for synchrocheck will be considered “Dead” or de-energized.
• SYNCHK1 LIVE V1 MIN VOLT: This setting establishes a minimum voltage magnitude for V1 in ‘pu’. Above this mag-
nitude, the V1 voltage input used for synchrocheck will be considered “Live” or energized.
• SYNCHK1 LIVE V2 MIN VOLT: This setting establishes a minimum voltage magnitude for V2 in ‘pu’. Above this mag-
nitude, the V2 voltage input used for synchrocheck will be considered “Live” or energized.
NOTES ON THE SYNCHROCHECK FUNCTION:
1. The selected sources for synchrocheck inputs V1 and V2 (which must not be the same source) may include both a
three-phase and an auxiliary voltage. The relay will automatically select the specific voltages to be used by the syn-
chrocheck element in accordance with the following table.
NO. V1 OR V2 V2 OR V1 AUTO-SELECTED AUTO-SELECTED VOLTAGE

(SOURCE Y) (SOURCE Z) COMBINATION
SOURCE Y SOURCE Z
1 Phase VTs and Phase VTs and Phase Phase VAB
Auxiliary VT Auxiliary VT
2 Phase VTs and Phase VT Phase Phase VAB
Auxiliary VT
3 Phase VT Phase VT Phase Phase VAB

NO. V1 OR V2 V2 OR V1 AUTO-SELECTED AUTO-SELECTED VOLTAGE

(SOURCE Y) (SOURCE Z) COMBINATION
SOURCE Y SOURCE Z
4 Phase VT and Auxiliary VT Phase Auxiliary V auxiliary
Auxiliary VT (as set for Source z)
5 Auxiliary VT Auxiliary VT Auxiliary Auxiliary V auxiliary
(as set for selected sources)
The voltages V1 and V2 will be matched automatically so that the corresponding voltages from the two sources will be
used to measure conditions. A phase to phase voltage will be used if available in both sources; if one or both of the
Sources have only an auxiliary voltage, this voltage will be used. For example, if an auxiliary voltage is programmed to
VAG, the synchrocheck element will automatically select VAG from the other source. If the comparison is required on a
specific voltage, the user can externally connect that specific voltage to auxiliary voltage terminals and then use this
"Auxiliary Voltage" to check the synchronism conditions.
If using a single CT/VT module with both phase voltages and an auxiliary voltage, ensure that only the auxiliary voltage
is programmed in one of the sources to be used for synchrocheck.
Exception: Synchronism cannot be checked between Delta connected phase VTs and a Wye connected auxil-
iary voltage.
NOTE
2. The relay measures frequency and Volts/Hz from an input on a given source with priorities as established by the con-
figuration of input channels to the source. The relay will use the phase channel of a three-phase set of voltages if pro-
grammed as part of that source. The relay will use the auxiliary voltage channel only if that channel is programmed as
part of the Source and a three-phase set is not.

FLEXLOGIC OPERAND
AND SYNC1 V2 ABOVE MIN
FLEXLOGIC OPERAND
AND SYNC1 V1 ABOVE MIN
FLEXLOGIC OPERAND
AND SYNC1 V1 BELOW MAX
SETTINGS FLEXLOGIC OPERAND

Function AND SYNC1 V2 BELOW MAX
Enabled = 1
AND
Block
Off = 0
AND
FLEXLOGIC OPERANDS
AND SYNC1 DEAD S OP
AND SYNC1 DEAD S DPO
SETTING
Dead Source Select FLEXLOGIC OPERANDS
AND OR OR SYNC1 CLS OP
None
LV1 and DV2 SYNC1 CLS DPO
DV1 and LV2
AND
DV1 or DV2
DV1 xor DV2
DV1 and DV2
AND
SETTING
Dead V1 Max Volt
V1 ≤ Maximum
XOR
SETTING
Dead V2 Max Volt
OR
V2 ≤ Maximum
SETTING
5
Live V1 Min Volt
AND
V1 ≥ Minimum
SETTING
Live V2 Min Volt
AND
V2 ≥ Minimum
SETTING
CALCULATE Max Volt Diff
SETTING Magnitude V1 Calculate
ΔV ≤ Maximum
V1 Source Angle Φ1 I V1 – V2 I = ΔV
= SRC 1 Frequency F1 FLEXLOGIC OPERANDS
AND SYNC1 SYNC OP
SETTING
SYNC1 SYNC DPO
Max Angle Diff
Calculate
ΔΦ ≤ Maximum
I Φ1 – Φ2 I = ΔΦ
SETTINGS SYNCHROCHECK 1
CALCULATE Max Freq Diff
SETTING Magnitude V2 Freq Hysteresis
V2 Source Angle Φ2 Calculate
ΔF ≤ Maximum
= SRC 2 Frequency F2 I F1 – F2 I = ΔF
ACTUAL VALUES
Synchrocheck 1 ΔV
Synchrocheck 1 ΔΦ
Synchrocheck 1 ΔF
827076AD.CDR
Figure 5–142: SYNCHROCHECK SCHEME LOGIC

5.7.10 AUTORECLOSE
PATH: SETTINGS  CONTROL ELEMENTS  AUTORECLOSE  AUTORECLOSE
 AUTORECLOSE AR FUNCTION: Range: Disabled, Enabled

 Disabled
AR MODE: Range: Mode 1(1 & 3 Pole), Mode 2 (1 Pole), Mode 3 (3
MESSAGE Pole-A), Mode 4 (3 Pole-B)
Mode 1 (1 & 3 Pole)
Mode 1 Activation: Range: FlexLogic operand
MESSAGE
Off
MESSAGE
Off
MESSAGE
Off
MESSAGE
Off
AR MAX NUMBER OF Range: 1, 2, 3, 4
MESSAGE
SHOTS: 2
AR INITIATE MODE: Range: Protection AND CB, Protection Only
MESSAGE
Protection AND CB
AR BLOCK BKR1: Range: FlexLogic operand
5 MESSAGE
Off
AR CLOSE TIME BKR 1: Range: 0.00 to 655.35 s in steps of 0.01
MESSAGE
0.10 s
AR BKR MAN CLOSE: Range: FlexLogic operand
MESSAGE
Off
AR BLK TIME UPON MAN Range: 0.00 to 655.35 s in steps of 0.01
MESSAGE
CLS: 10.00 s
AR 1P INIT: Range: FlexLogic operand
MESSAGE
Off
AR 3P INIT: Range: FlexLogic operand
MESSAGE
Off
AR 3P TD INIT: Range: FlexLogic operand
MESSAGE
Off
AR MULTI-P FAULT: Range: FlexLogic operand
MESSAGE
Off
BKR ONE POLE OPEN: Range: FlexLogic operand
MESSAGE
Off
BKR 3 POLE OPEN: Range: FlexLogic operand
MESSAGE
Off
AR 3-P DEAD TIME 1: Range: 0.00 to 655.35 s in steps of 0.01
MESSAGE
0.50 s
MESSAGE
1.20 s
MESSAGE
2.00 s


MESSAGE
4.00 s
AR EXTEND DEAD T 1: Range: FlexLogic operand
MESSAGE
Off
AR DEAD TIME 1 Range: 0.00 to 655.35 s in steps of 0.01
MESSAGE
EXTENSION: 0.50 s
AR RESET: Range: FlexLogic operand
MESSAGE
Off
AR RESET TIME: Range: 0 to 655.35 s in steps of 0.01
MESSAGE
60.00 s
AR BKR CLOSED: Range: FlexLogic operand
MESSAGE
Off
AR BLOCK: Range: FlexLogic operand
MESSAGE
Off
AR PAUSE: Range: FlexLogic operand
MESSAGE
Off
AR INCOMPLETE SEQ Range: 0 to 655.35 s in steps of 0.01
MESSAGE
TIME: 5.00 s
AR BLOCK BKR2: Range: FlexLogic operand
MESSAGE
Off
AR CLOSE TIME BKR2: Range: 0.00 to 655.35 s in steps of 0.01 5
MESSAGE
0.10 s
AR TRANSFER 1 TO 2: Range: Yes, No
MESSAGE
No
AR TRANSFER 2 TO 1: Range: Yes, No
MESSAGE
No
AR BKR1 FAIL OPTION: Range: Continue, Lockout
MESSAGE
Continue
AR BKR2 FAIL OPTION: Range: Continue, Lockout
MESSAGE
Continue
AR 1-P DEAD TIME: Range: 0 to 655.35 s in steps of 0.01
MESSAGE
1.00 s
AR BKR SEQUENCE: Range: 1, 2, 1&2, 1–2, 2–1
MESSAGE
1-2
AR TRANSFER TIME: Range: 0 to 655.35 s in steps of 0.01
MESSAGE
4.00 s
AR BUS FLT INIT: Range: FlexLogic operand
MESSAGE
Off
AR EVENT: Range: Enabled, Disabled
MESSAGE
Disabled
The autoreclose scheme is intended for use on transmission lines with circuit breakers operated in both the single pole and
three pole modes, in one or two breaker arrangements. The autoreclose scheme provides four programs with different
operating cycles, depending on the fault type. Each of the four programs can be set to trigger up to four reclosing attempts.
The second, third, and fourth attempts always perform three-pole reclosing and have independent dead time delays.

When used in two breaker applications, the reclosing sequence is selectable. The reclose signal can be sent to one
selected breaker only, to both breakers simultaneously or to both breakers in sequence (one breaker first and then, after a
delay to check that the reclose was successful, to the second breaker). When reclosing in sequence, the first breaker
should reclose with either the single-pole or three-pole dead time according to the fault type and reclose mode; the second
breaker should follow the successful reclosure of the first breaker. When reclosing simultaneously, for the first shot both
breakers should reclose with either the single-pole or three-pole dead time, according to the fault type and the reclose
mode.
The signal used to initiate the autoreclose scheme is the trip output from protection. This signal can be single pole tripping
for single phase faults and three phase tripping for multi-phase faults. The autoreclose scheme has five operating states.
STATE CHARACTERISTICS
Enabled Scheme is permitted to operate
Disabled Scheme is not permitted to operate
Reset Scheme is permitted to operate and shot count is reset to 0
Reclose in progress Scheme has been initiated but the reclose cycle is not finished (successful or not)
Lockout Scheme is not permitted to operate until reset received
AR PROGRAMS:
The autorecloser provides four programs that can cause from one to four reclose attempts (shots). After the first shot, all
subsequent recloses are always be three-pole. If the maximum number of shots selected is “1” (only one reclose attempt)
and the fault is persistent, after the first reclose the scheme goes to lockout upon another Initiate signal.
For the 3-pole reclose programs (modes 3 and 4), an AR FORCE 3-P FlexLogic operand is set. This operand can be used in
connection with the tripping logic to cause a three-pole trip for single-phase faults.
5
Table 5–32: AUTORECLOSE PROGRAMS
MODE AR MODE FIRST SHOT SECOND SHOT THIRD SHOT FOURTH SHOT
SINGLE- MULTI- SINGLE- MULTI- SINGLE- MULTI- SINGLE- MULTI-
PHASE PHASE PHASE PHASE PHASE PHASE PHASE PHASE
FAULT FAULT FAULT FAULT FAULT FAULT FAULT FAULT
1 1 & 3 POLE 1 POLE 3 POLE 3 POLE or 3 POLE or 3 POLE or 3 POLE or 3 POLE or 3 POLE or
LO LO LO LO LO LO
2 1 POLE 1 POLE LO 3 POLE or 3 POLE or 3 POLE or 3 POLE or 3 POLE or 3 POLE or
LO LO LO LO LO LO
3 3 POLE-A 3 POLE LO 3 POLE or LO 3 POLE or LO 3 POLE or LO
LO LO LO
4 3 POLE-B 3 POLE 3 POLE 3 POLE or 3 POLE or 3 POLE or 3 POLE or 3 POLE or 3 POLE or
LO LO LO LO LO LO
The four autoreclose modes are described as follows.

1. “1 & 3 Pole”: In this mode, the autorecloser starts the AR 1-P DEAD TIME timer for the first shot if the autoreclose is sin-
gle-phase initiated, the AR 3-P DEAD TIME 1 timer if the autoreclose is three-pole initiated, and the AR 3-P DEAD TIME 2
timer if the autoreclose is three-phase time delay initiated. If two or more shots are enabled, the second, third, and
fourth shots are always three-pole and start the AR 3-P DEAD TIME 2(4) timers.
2. “1 Pole”: In this mode, the autorecloser starts the AR 1-P DEAD TIME for the first shot if the fault is single phase. If the
fault is three-phase or a three-pole trip on the breaker occurred during the single-pole initiation, the scheme goes to
lockout without reclosing. If two or more shots are enabled, the second, third, and fourth shots are always three-pole
and start the AR 3-P DEAD TIME 2(4) timers.
3. “3 Pole-A”: In this mode, the autorecloser is initiated only for single phase faults, although the trip is three pole. The
autorecloser uses the AR 3-P DEAD TIME 1 for the first shot if the fault is single phase. If the fault is multi phase the
scheme will go to Lockout without reclosing. If two or more shots are enabled, the second, third, and fourth shots are
always three-phase and start the AR 3-P DEAD TIME 2(4) timers.
4. “3 Pole-B”: In this mode, the autorecloser is initiated for any type of fault and starts the AR 3-P DEAD TIME 1 for the first
shot. If the initiating signal is AR 3P TD INIT the scheme starts AR 3-P DEAD TIME 2 for the first shot. If two or more shots
are enabled, the second, third, and fourth shots are always three-phase and start the AR 3-P DEAD TIME 2(4) timers.

BASIC RECLOSING OPERATION:

Reclosing operation is determined primarily by the AR MODE and AR BKR SEQUENCE settings. The reclosing sequences are
started by the initiate inputs. A reclose initiate signal sends the scheme into the reclose-in-progress (RIP) state, asserting
the AR RIP FlexLogic operand. The scheme is latched into the RIP state and resets only when an AR CLS BKR 1 (autore-
close breaker 1) or AR CLS BKR 2 (autoreclose breaker 2) operand is generated or the scheme goes to the Lockout state.
The dead time for the initial reclose operation is determined by either the AR 1-P DEAD TIME, AR 3-P DEAD TIME 1, or AR 3-P
DEAD TIME 2 setting, depending on the fault type and the mode selected. After the dead time interval the scheme asserts the
AR CLOSE BKR 1 or AR CLOSE BKR 2 operands, as determined by the sequence selected. These operands are latched until
the breaker closes or the scheme goes to Reset or Lockout.
There are three initiate programs: single pole initiate, three pole initiate and three pole, time delay initiate. Any of these
reclose initiate signals start the reclose cycle and set the reclose-in-progress (AR RIP) operand. The reclose-in-progress
operand is sealed-in until the Lockout or Reset signal appears.
The three-pole initiate and three-pole time delay initiate signals are latched until the CLOSE BKR1 OR BKR2 or Lockout or
Reset signal appears.
AR PAUSE:
The pause input offers the possibility of freezing the autoreclose cycle until the pause signal disappears. This can be done
when a trip occurs and simultaneously or previously, some conditions are detected such as out-of step or loss of guard fre-
quency, or a remote transfer trip signal is received. The pause signal freezes all four dead timers. When the ‘pause’ signal
disappears the autoreclose cycle is resumed by continuing the shot timer it was left at when paused.
This feature can be also used when a transformer is tapped from the protected line and a reclose is not desirable until the
transformer is removed from the line. In this case, the reclose scheme is ‘paused’ until the transformer is disconnected. The
AR PAUSE input will force a three-pole trip through the 3-P DEADTIME 2 path.
EVOLVING FAULTS: 5
1.25 cycles after the single pole dead time has been initiated, the AR FORCE 3P TRIP operand is set and it will be reset only
when the scheme is reset or goes to Lockout. This will ensure that when a fault on one phase evolves to include another
phase during the single pole dead time of the auto-recloser the scheme will force a 3 pole trip and reclose.
RECLOSING SCHEME OPERATION FOR ONE BREAKER:
• Permanent Fault: Consider Mode 1, which calls for 1-Pole or 3-Pole Time Delay 1 for the first reclosure and 3-Pole
Time Delay 2 for the second reclosure, and assume a permanent fault on the line. Also assume the scheme is in the
Reset state. For the first single-phase fault the AR 1-P DEAD TIME timer will be started, while for the first multi-phase fault
the AR 3-P DEAD TIME 1 timer will be started. If the AR 3P TD INIT signal is high, the AR 3-P DEAD TIME 2 will be started for
the first shot.
If AR MAX NO OF SHOTS is set to “1”, upon the first reclose the shot counter is set to 1. Upon reclosing, the fault is again
detected by protection and reclose is initiated. The breaker is tripped three-pole through the AR SHOT COUNT >0 oper-
and that will set the AR FORCE 3P operand. Because the shot counter has reached the maximum number of shots per-
mitted the scheme is sent to the Lockout state.
If AR MAX NO OF SHOTS is set to “2”, upon the first reclose the shot counter is set to 1. Upon reclosing, the fault is again
detected by protection and reclose is initiated. The breaker is tripped three-pole through the AR SHOT COUNT >0 oper-
and that will set the AR FORCE 3P operand. After the second reclose the shot counter is set to 2. Upon reclosing, the
fault is again detected by protection, the breaker is tripped three-pole, and reclose is initiated again. Because the shot
counter has reached the maximum number of shots permitted the scheme is sent to the lockout state.
• Transient Fault: When a reclose output signal is sent to close the breaker the reset timer is started. If the reclosure
sequence is successful (there is no initiating signal and the breaker is closed) the reset timer will time out returning the
scheme to the reset state with the shot counter set to "0" making it ready for a new reclose cycle.
RECLOSING SCHEME OPERATION FOR TWO BREAKERS:
• Permanent Fault: The general method of operation is the same as that outlined for the one breaker applications
except for the following description, which assumes AR BKR SEQUENCE is “1-2” (reclose Breaker 1 before Breaker 2)
The signal output from the dead time timers passes through the breaker selection logic to initiate reclosing of Breaker
1. The Close Breaker 1 signal will initiate the Transfer Timer. After the reclose of the first breaker the fault is again
detected by the protection, the breaker is tripped three pole and the autoreclose scheme is initiated. The Initiate signal
will stop the transfer timer. After the 3-P dead time times out the Close Breaker 1 signal will close first breaker again

and will start the transfer timer. Since the fault is permanent the protection will trip again initiating the autoreclose
scheme that will be sent to Lockout by the SHOT COUNT = MAX signal.
• Transient Fault: When the first reclose output signal is sent to close Breaker 1, the reset timer is started. The close
Breaker 1 signal initiates the transfer timer that times out and sends the close signal to the second breaker. If the reclo-
sure sequence is successful (both breakers closed and there is no initiating signal) the reset timer will time out, return-
ing the scheme to the reset state with the shot counter set to 0. The scheme will be ready for a new reclose cycle.
AR BKR1(2) RECLS FAIL:
If the selected sequence is “1–2” or “2–1” and after the first or second reclose attempt the breaker fails to close, there are
two options. If the AR BKR 1(2) FAIL OPTION is set to “Lockout”, the scheme will go to lockout state. If the AR BKR 1(2) FAIL
OPTION is set to “Continue”, the reclose process will continue with Breaker 2. At the same time the shot counter will be
decreased (since the closing process was not completed).
SCHEME RESET AFTER RECLOSURE:
When a reclose output signal is sent to close either breaker 1 or 2 the reset timer is started. If the reclosure sequence is
successful (there is no initiating signal and the breakers are closed) the reset timer will time out, returning the scheme to
the reset state, with the shot counter set to 0, making it ready for a new reclose cycle.
In two breaker schemes, if one breaker is in the out-of-service state and the other is closed at the end of the reset time, the
scheme will also reset. If at the end of the reset time at least one breaker, which is not in the out-of-service state, is open
the scheme will be sent to Lockout.
The reset timer is stopped if the reclosure sequence is not successful: an initiating signal present or the scheme is in Lock-
out state. The reset timer is also stopped if the breaker is manually closed or the scheme is otherwise reset from lockout.
LOCKOUT:
5 When a reclose sequence is started by an initiate signal the scheme moves into the reclose-in-progress state and starts the
incomplete sequence timer. The setting of this timer determines the maximum time interval allowed for a single reclose
shot. If a close breaker 1 or 2 signal is not present before this time expires, the scheme goes to “Lockout”.
There are four other conditions that can take the scheme to the Lockout state, as shown below:
• Receipt of ‘Block’ input while in the reclose-in-progress state
• The reclosing program logic: when a 3P Initiate is present and the autoreclose mode is either 1 Pole or 3Pole-A (3 pole
autoreclose for single pole faults only)
• Initiation of the scheme when the count is at the maximum allowed
• If at the end of the reset time at least one breaker, which is not in the out-of-service state, is open the scheme will be
sent to Lockout. The scheme will be also sent to Lockout if one breaker fails to reclose and the setting AR BKR FAIL
OPTION is set to “Lockout”.
Once the Lockout state is set it will be latched until one or more of the following occurs:
• The scheme is intentionally reset from Lockout, employing the Reset setting of the Autorecloser;
• The Breaker(s) is(are) manually closed from panel switch, SCADA or other remote control through the AR BRK MAN
CLOSE setting;
• 10 seconds after breaker control detects that breaker(s) were closed.

BREAKER OPEN BEFORE FAULT:
A logic circuit is provided that inhibits the close breaker 1 and close breaker 2 outputs if a reclose initiate (RIP) indicator is
not present within 30 ms of the Breaker Any Phase Open input. This feature is intended to prevent reclosing if one of the
breakers was open in advance of a reclose initiate input to the recloser. This logic circuit resets when the breaker is closed.
TRANSFER RECLOSE WHEN BREAKER IS BLOCKED:
1. When the reclosing sequence 1-2 is selected and Breaker 1 is blocked (AR BKR1 BLK operand is set) the reclose signal
can be transferred direct to the Breaker 2 if AR TRANSFER 1 TO 2 is set to “Yes”. If set to “No”, the scheme will be sent to
Lockout by the incomplete sequence timer.
2. When the reclosing sequence 2-1 is selected and Breaker 2 is blocked (AR BKR2 BLK operand is set) the reclose signal
can be transferred direct to the Breaker 1 if AR TRANSFER 2 TO 1 is set to “Yes”. If set to “No” the scheme will be sent to
Lockout by the incomplete sequence timer.

FORCE 3-POLE TRIPPING:

The reclosing scheme contains logic that is used to signal trip logic that three-pole tripping is required for certain conditions.
This signal is activated by any of the following:
• Autoreclose scheme is paused after it was initiated.
• Autoreclose scheme is in the lockout state.
• Autoreclose mode is programmed for three-pole operation
• The shot counter is not at 0; that is, the scheme is not in the reset state. This ensures a second trip will be three-pole
when reclosing onto a permanent single phase fault.
• 1.25 cycles after the single-pole reclose is initiated by the AR 1P INIT signal.
ZONE 1 EXTENT:
The zone 1 extension philosophy here is to apply an overreaching zone permanently as long as the relay is ready to
reclose, and reduce the reach when reclosing. Another zone 1 extension approach is to operate normally from an under-
reaching zone, and use an overreaching distance zone when reclosing the line with the other line end open. This philoso-
phy could be programmed via the line pickup scheme.
The “Extended Zone 1" is 0 when autoreclose is in lockout or disabled and 1 when autoreclose is in reset.
1. When "Extended Zone 1" is 0, the distance functions shall be set to normal underreach Zone 1 setting.
2. When "Extended Zone 1" is 1, the distance functions may be set to Extended Zone 1 Reach, which is an overreaching
setting.
3. During a reclose cycle, "Extended Zone 1" goes to 0 as soon as the first CLOSE BREAKER signal is issued (AR SHOT
COUNT > 0) and remains 0 until the recloser goes back to reset.
USE OF SETTINGS: 5
The single-phase autoreclose settings are described here.
• AR MODE: This setting selects the Autoreclose operating mode from the four available reclose modes (Mode 1: 1 & 3
Pole, Mode 2: 1 Pole, Mode 3: 3 Pole-A and Mode 4: 3 Pole-B), which functions in conjunction with signals received at
the initiation inputs as described previously. The autorecloser runs in this mode until a different mode is activated
through the AR Mode Activation inputs explained as follows.
• MODE 1 to MODE 4 ACTIVATION: This setting selects an operand for activating the corresponding AR mode in run-
time. Mode change via activation input takes place when only one of the four activation inputs is high and the AR RIP
operand is low (that is, reclose is not in progress) and also the mode to be activated is different from the existing mode,
otherwise the activation input is ignored and the existing mode continues to be used. See details in the Mode Control
Logic diagram.
• AR MAX NUMBER OF SHOTS: This setting specifies the number of reclosures that can be attempted before reclo-
sure goes to lockout when the fault is permanent.
• AR INITIATE MODE: This setting selects the autoreclose initiation mode. When selected as “Protection AND CB”, the
autoreclose element is initiated by protection operation and begins incrementing the autoreclose dead time timer when
a circuit breaker is open. Breaker status is determined from breaker auxiliary contacts which should be correctly config-
ured in breaker settings. In “Protection only” initiation mode, the autoreclose element is initiated by protection opera-
tion and begins incrementing the dead time when protection resets, without the need of breaker auxiliary contacts.
• AR BLOCK BKR1: This input selects an operand that will block the reclose command for breaker 1. This condition can
be for example: breaker low air pressure, reclose in progress on another line (for the central breaker in a breaker and
a half arrangement), or a sum of conditions combined in FlexLogic.
• AR CLOSE TIME BKR1:This setting represents the closing time for the breaker 1 from the moment the “Close” com-
mand is sent to the moment the contacts are closed.
• AR BKR MAN CLOSE: This setting selects a FlexLogic operand that represents manual close command to a breaker
associated with the autoreclose scheme.
• AR BLK TIME UPON MAN CLS: The autoreclose scheme can be disabled for a programmable time delay after an
associated circuit breaker is manually commanded to close, preventing reclosing onto an existing fault such as
grounds on the line. This delay must be longer than the slowest expected trip from any protection not blocked after

manual closing. If the autoreclose scheme is not initiated after a manual close and this time expires the autoreclose
scheme is set to the reset state.
• AR 1P INIT: This setting selects a FlexLogic operand that is intended to initiate single-pole autoreclosure.
• AR 3P INIT: This setting selects a FlexLogic operand that is intended to initiate three-pole autoreclosure, first timer (AR
3P DEAD TIME 1) that can be used for a high-speed autoreclosure.
• AR 3P TD INIT: This setting selects a FlexLogic operand intended to initiate three-pole autoreclosure. second timer
(AR 3P DEAD TIME 2) can be used for a time-delay autoreclosure. If the operand assigned to this setting and the AR 3P
INIT setting are asserted simultaneously, then autoreclose will not activate the first and second shot timers at the same
time. Instead, the priority is given to the AR 3P INIT operand.
• AR MULTI-P FAULT: This setting selects a FlexLogic operand that indicates a multi-phase fault. The operand value
should be zero for single-phase to ground faults.
• BKR ONE POLE OPEN: This setting selects a FlexLogic operand which indicates that the breaker has opened cor-
rectly following a single phase to ground fault and the autoreclose scheme can start timing the single pole dead time
(for 1-2 reclose sequence for example, breaker 1 should trip single pole and breaker 2 should trip 3 pole).
The scheme has a pre-wired input that indicates breaker status.
• BKR 3 POLE OPEN: This setting selects a FlexLogic operand which indicates that the breaker has opened three pole
and the autoreclose scheme can start timing the three pole dead time. The scheme has a pre-wired input that indicates
breaker status.
• AR 3-P DEAD TIME 1: This is the dead time following the first three pole trip. This intentional delay can be used for a
high-speed three-pole autoreclose. However, it should be set longer than the estimated de-ionizing time following the
three-pole trip.
5 • AR 3-P DEAD TIME 2: This is the dead time following the second three-pole trip or initiated by the AR 3P TD INIT input.
This intentional delay is typically used for a time delayed three-pole autoreclose (as opposed to high speed three-pole
autoreclose).
• AR 3-P DEAD TIME 3: This setting represents the dead time following the third three-pole trip.
• AR 3-P DEAD TIME 4: This setting represents the dead time following the third three-pole trip.
• AR EXTEND DEAD T 1: This setting selects an operand that will adapt the duration of the dead time for the first shot
to the possibility of non-simultaneous tripping at the two line ends. Typically this is the operand set when the communi-
cation channel is out of service
• AR DEAD TIME 1 EXTENSION: This timer is used to set the length of the dead time 1 extension for possible non-
simultaneous tripping of the two ends of the line.
• AR RESET: This setting selects the operand that forces the autoreclose scheme from any state to reset. Typically this
is a manual reset from lockout, local or remote.
• AR RESET TIME: A reset timer output resets the recloser following a successful reclosure sequence. The setting is
based on the breaker time which is the minimum time required between successive reclose sequences.
• AR BKR CLOSED: This setting selects an operand that indicates that the breakers are closed at the end of the reset
time and the scheme can reset.
• AR BLOCK: This setting selects the operand that blocks the autoreclose scheme (it can be a sum of conditions such
as: time delayed tripping, breaker failure, bus differential protection, etc.). If the block signal is present before autore-
close scheme initiation the AR DISABLED FlexLogic operand will be set. If the block signal occurs when the scheme is
in the RIP state the scheme will be sent to lockout.
• AR PAUSE: The pause input offers the ability to freeze the autoreclose cycle until the pause signal disappears. This
may be done when a trip occurs and simultaneously or previously, some conditions are detected such as out-of step or
loss of guard frequency, or a remote transfer trip signal is received. When the pause signal disappears the autoreclose
cycle is resumed. This feature can also be used when a transformer is tapped from the protected line and a reclose is
not desirable until it is disconnected from the line. In this situation, the reclose scheme is paused until the transformer
is disconnected.
• AR INCOMPLETE SEQ TIME: This timer is used to set the maximum time interval allowed for a single reclose shot. It
is started whenever a reclosure is initiated and is active until the CLOSE BKR1 or CLOSE BKR2 signal is sent. If all con-
ditions allowing a breaker closure are not satisfied when this time expires, the scheme goes to “Lockout”. The mini-

mum permissible setting is established by the AR 3-P DEAD TIME 2 timer setting. Settings beyond this will determine the
wait time for the breaker to open so that the reclose cycle can continue and/or for the AR PAUSE signal to reset and
allow the reclose cycle to continue and/or for the AR BKR1 BLK signal to disappear and allow the AR CLOSE BKR1 signal
to be sent.
• AR BLOCK BKR2: This input selects an operand that will block the reclose command for breaker 2. This condition can
be for example: breaker low air pressure, reclose in progress on another line (for the central breaker in a breaker and
a half arrangement), or a sum of conditions combined in FlexLogic.
• AR CLOSE TIME BKR2: This setting represents the closing time for the breaker 2 from the moment the ‘Close’ com-
mand is sent to the moment the contacts are closed.
• AR TRANSFER 1 TO 2: This setting establishes how the scheme performs when the breaker closing sequence is 1-2
and breaker 1 is blocked. When set to “Yes” the closing command will be transferred direct to breaker 2 without waiting
the transfer time. When set to “No” the closing command will be blocked by the AR BKR1 BLK signal and the scheme
will be sent to lockout by the incomplete sequence timer.
• AR TRANSFER 2 TO 1: This setting establishes how the scheme performs when the breaker closing sequence is 2-1
and breaker 2 is blocked. When set to “Yes” the closing command will be transferred direct to breaker 1 without waiting
the transfer time. When set to “No”, the closing command will be blocked by the AR BKR2 BLK signal and the scheme
will be sent to lockout by the incomplete sequence timer.
• AR BKR1 FAIL OPTION: This setting establishes how the scheme performs when the breaker closing sequence is 1-
2 and Breaker 1 has failed to close. When set to “Continue” the closing command will be transferred to breaker 2 which
will continue the reclosing cycle until successful (the scheme will reset) or unsuccessful (the scheme will go to Lock-
out). When set to “Lockout” the scheme will go to lockout without attempting to reclose breaker 2.
• AR BKR2 FAIL OPTION: This setting establishes how the scheme performs when the breaker closing sequence is 2-
1 and Breaker 2 has failed to close. When set to “Continue” the closing command will be transferred to breaker 1 which
will continue the reclosing cycle until successful (the scheme will reset) or unsuccessful (the scheme will go to Lock- 5
out). When set to “Lockout” the scheme will go to lockout without attempting to reclose breaker 1.
• AR 1-P DEAD TIME: Set this intentional delay longer than the estimated de-ionizing time after the first single-pole trip.
• AR BREAKER SEQUENCE: This setting selects the breakers reclose sequence: Select “1” for reclose breaker 1 only,
“2” for reclose breaker 2 only, “1&2” for reclose both breakers simultaneously, “1-2” for reclose breakers sequentially;
Breaker 1 first, and “2-1” for reclose breakers sequentially; Breaker 2 first.
• AR TRANSFER TIME: The transfer time is used only for breaker closing sequence 1-2 or 2-1, when the two breakers
are reclosed sequentially. The transfer timer is initiated by a close signal to the first breaker. The transfer timer trans-
fers the reclose signal from the breaker selected to close first to the second breaker. The time delay setting is based on
the maximum time interval between the autoreclose signal and the protection trip contact closure assuming a perma-
nent fault (unsuccessful reclose). Therefore, the minimum setting is equal to the maximum breaker closing time plus
the maximum line protection operating time plus a suitable margin. This setting will prevent the autoreclose scheme
from transferring the close signal to the second breaker unless a successful reclose of the first breaker occurs.
• AR BUS FLT INIT: This setting is used in breaker-and-a-half applications to allow the autoreclose control function to
perform reclosing with only one breaker previously opened by bus protection. For line faults, both breakers must open
for the autoreclose reclosing cycles to take effect.

Figure 5–143: SINGLE-POLE AUTORECLOSE LOGIC (Sheet 1 of 3)

In runtime, AR mode can be changed through the mode control logic as shown in the following diagram. Initially, the autore-
closer runs in the mode as per AR MODE setting. Then the relay checks the AR activation inputs in each protection pass.
The AR mode is switched to the new mode when
• Only one of four activation inputs is high, and
• AP RIP operand is low, and
• The mode to be activated is different from the current AR mode
The logic allows activation of one mode at a time. Simultaneous multiple activations are ignored and mode switching does
not happen. However, a FlexLogic operand, AR MODE SWITCH FAIL, is asserted if either simultaneous multiple activa-
tions are initiated, or a single activation is initiated but recloser is already in progress.

The active AR mode is memorized (latched) on power cycling. This means that the relay uses the last-used mode on
power-up. The AR mode resets to the default mode (specified by the AR MODE setting) when any settings in the autore-
close function are changed.
Figure 5–144: MODE CONTROL LOGIC
Multiple (>1)
inputs are
high
FLEXLOGIC OPERAND
OR
AR MODE SWITCH FAIL
AND
FLEXLOGIC OPERAND
AR MODE =1
FLEXLOGIC OPERAND AR MODE =2
AR RIP AR MODE =3
AR MODE =4
SETTING
Only 1
out of 4 AR M0DE:
SETTING
is high Mode 1: 1 & 3 Pole Current AR Mode
AR Mode Activation AND Mode 2: 1 Pole
b=1….4
Mode 1: Off = 0 Mode 3: 3 Pole - A
Mode 2: Off = 0 Mode to be activated Mode 4: 3 Pole -B
Switch to
Mode 3: Off = 0 a=1….4 a new mode
1 if a ≠ b
Mode 4: Off = 0 Note: only one mode can =
0 otherwise
be activated at a time. b
Simultaneous multiple
modes activation will be
ignored. 427248A1.vsd
In addition, the current AR mode is available as FlexLogic Operands because AR Mode equals to 1, 2, 3, and 4 respec-
tively so that it can be monitored and logged.


BKR 1 MNL OPEN

From sheet 2 }
}
FLEXLOGIC OPERAND OR
From BREAKER 1 OOS

Breaker Control
scheme FLEXLOGIC OPERAND
BREAKER 2 OOS
OR
}
BKR 2 MNL OPEN
1
2
From sheet 2 1&2
1-2
2-1
OR
}
AND
FLEXLOGIC OPERAND
BREAKER 1 MNL CLS
BKR MANUAL CLOSE

OR
(To sheet 1)
OR
AND
FLEXLOGIC OPERAND
BREAKER 2 MNL CLS
FLEXLOGIC OPERAND
AND
BREAKER 1 CLOSED
FLEXLOGIC OPERAND
AND
BREAKER 2 CLOSED
AND
BKR CLOSED
5
OR (To sheet 1 and 2)
OR
From
Breaker Control
scheme
AND
AND
FLEXLOGIC OPERAND
AND
BREAKER 1 OPEN
OR
FLEXLOGIC OPERAND
AND
BREAKER 2 OPEN
OR BKR 3 POLE OPEN
(To sheet 1)
OR
FLEXLOGIC OPERAND AND
BUS-FLT INIT
OR AND
OFF = 0
AND
AND
FLEXLOGIC OPERAND
AND
BREAKER 1 ONE P OPEN
OR
FLEXLOGIC OPERAND
AND
BREAKER 2 ONE P OPEN
OR AND BKR ONE POLE OPEN

OR (To sheet 1)
OR
OR
AND
OR
AND
827833AA.CDR

5
5-276
1ST SHOT 2ND SHOT
F R
A T PROT E
T
U R T TRIP BKR S
L I T PROT RESET E
T P T
5.7 CONTROL ELEMENTS
PREFAULT
AR 1P INIT
AR RIP
1-P DEAD TIME
AR 1-P RIP
1.25 cycle
AR FORCE 3P TRIP
CLOSE
AR CLOSE BKR1
T CLOSE BKR1 T CLOSE BKR1
AR RESET TIME
RESET TIME
AR SHOT COUNT > 0
BREAKER 1 CLOSED
T TRIP BKR T PROT RESET
T PROT
AR 3P INIT
3-P/2 DEAD TIME
D60 Line Distance Protection System

AR 3P/2 RIP
BREAKER 2 CLOSED
Figure 5–147: EXAMPLE RECLOSING SEQUENCE

AR CLOSE BKR2
T CLOSE BKR2
TRANSFER TIME
AR TRANSFER TIME
AR INCOMPLETE SEQ. TIME

842703A4.CDR
5 SETTINGS
GE Multilin
5.7.11 DIGITAL ELEMENTS
PATH: SETTINGS  CONTROL ELEMENTS  DIGITAL ELEMENTS  DIGITAL ELEMENT 1(48)
 DIGITAL ELEMENT 1 DIGITAL ELEMENT 1 Range: Disabled, Enabled

DIG ELEM 1 NAME: Range: 16 alphanumeric characters
MESSAGE
Dig Element 1
DIG ELEM 1 INPUT: Range: FlexLogic operand
MESSAGE
Off
DIG ELEM 1 PICKUP Range: 0.000 to 999999.999 s in steps of 0.001
MESSAGE
DELAY: 0.000 s
DIG ELEM 1 RESET Range: 0.000 to 999999.999 s in steps of 0.001
MESSAGE
DELAY: 0.000 s
DIG ELEMENT 1 Range: Disabled, Enabled
MESSAGE
PICKUP LED: Enabled
DIG ELEM 1 BLOCK: Range: FlexLogic operand
MESSAGE
Off
DIGITAL ELEMENT 1 Range: Self-reset, Latched, Disabled
MESSAGE
TARGET: Self-reset
DIGITAL ELEMENT 1 Range: Disabled, Enabled
MESSAGE
EVENTS: Disabled 5
There are 48 identical digital elements available, numbered 1 to 48. A digital element can monitor any FlexLogic operand
and present a target message and/or enable events recording depending on the output operand state. The digital element
settings include a name which will be referenced in any target message, a blocking input from any selected FlexLogic oper-
and, and a timer for pickup and reset delays for the output operand.
• DIGITAL ELEMENT 1 INPUT: Selects a FlexLogic operand to be monitored by the digital element.
• DIGITAL ELEMENT 1 PICKUP DELAY: Sets the time delay to pickup. If a pickup delay is not required, set to "0".
• DIGITAL ELEMENT 1 RESET DELAY: Sets the time delay to reset. If a reset delay is not required, set to “0”.
• DIGITAL ELEMENT 1 PICKUP LED: This setting enables or disabled the digital element pickup LED. When set to
“Disabled”, the operation of the pickup LED is blocked.
Figure 5–148: DIGITAL ELEMENT SCHEME LOGIC

CIRCUIT MONITORING APPLICATIONS:
Some versions of the digital input modules include an active voltage monitor circuit connected across form-A contacts. The
voltage monitor circuit limits the trickle current through the output circuit (see technical specifications for form-A).

As long as the current through the voltage monitor is above a threshold (see technical specifications for form-A), the “Cont
Op 1 VOn” FlexLogic operand will be set (for contact input 1 – corresponding operands exist for each contact output). If the
output circuit has a high resistance or the DC current is interrupted, the trickle current will drop below the threshold and the
“Cont Op 1 VOff” FlexLogic operand will be set. Consequently, the state of these operands can be used as indicators of the
integrity of the circuits in which form-A contacts are inserted.
EXAMPLE 1: BREAKER TRIP CIRCUIT INTEGRITY MONITORING
In many applications it is desired to monitor the breaker trip circuit integrity so problems can be detected before a trip oper-
ation is required. The circuit is considered to be healthy when the voltage monitor connected across the trip output contact
detects a low level of current, well below the operating current of the breaker trip coil. If the circuit presents a high resis-
tance, the trickle current will fall below the monitor threshold and an alarm would be declared.
In most breaker control circuits, the trip coil is connected in series with a breaker auxiliary contact which is open when the
breaker is open (see diagram below). To prevent unwanted alarms in this situation, the trip circuit monitoring logic must
include the breaker position.
85VHULHVGHYLFH
ZLWKIRUP$FRQWDFWV
+D
,
+E '&²
9 '&
+F D 7ULSFRLO
5
, FXUUHQWPRQLWRU
9 YROWDJHPRQLWRU $&'5
Figure 5–149: TRIP CIRCUIT EXAMPLE 1

Assume the output contact H1 is a trip contact. Using the contact output settings, this output will be given an ID name; for
example, “Cont Op 1". Assume a 52a breaker auxiliary contact is connected to contact input H7a to monitor breaker status.
Using the contact input settings, this input will be given an ID name, for example, “Cont Ip 1", and will be set “On” when the
breaker is closed. The settings to use digital element 1 to monitor the breaker trip circuit are indicated below (EnerVista UR
Setup example shown):
The PICKUP DELAY setting should be greater than the operating time of the breaker to avoid nuisance alarms.
NOTE

EXAMPLE 2: BREAKER TRIP CIRCUIT INTEGRITY MONITORING

If it is required to monitor the trip circuit continuously, independent of the breaker position (open or closed), a method to
maintain the monitoring current flow through the trip circuit when the breaker is open must be provided (as shown in the fig-
ure below). This can be achieved by connecting a suitable resistor (see figure below) across the auxiliary contact in the trip
circuit. In this case, it is not required to supervise the monitoring circuit with the breaker position – the BLOCK setting is
selected to “Off”. In this case, the settings are as follows (EnerVista UR Setup example shown).
85VHULHVGHYLFH
ZLWKIRUP$FRQWDFWV
+D
9DOXHVIRUUHVLVWRU´5µ 5
3RZHUVXSSO\ 5HVLVWDQFH 3RZHU
,
9'& ű :
+E '&² 9'& ű :
9'& ű :
9 '&
9'& ű :
+F D 7ULSFRLO
9'& ű :
5
9'& ű :
%\SDVV
, FXUUHQWPRQLWRU UHVLVWRU
9 YROWDJHPRQLWRU $&'5
Figure 5–150: TRIP CIRCUIT EXAMPLE 2

The wiring connection for two examples above is applicable to both form-A contacts with voltage monitoring and
solid-state contact with voltage monitoring.
NOTE

5.7.12 DIGITAL COUNTERS
PATH: SETTINGS  CONTROL ELEMENTS  DIGITAL COUNTERS  COUNTER 1(8)
 COUNTER 1 COUNTER 1 Range: Disabled, Enabled

COUNTER 1 NAME: Range: 12 alphanumeric characters
MESSAGE
Counter 1
COUNTER 1 UNITS: Range: 6 alphanumeric characters
MESSAGE
COUNTER 1 PRESET: Range: –2,147,483,648 to +2,147,483,647

MESSAGE
0
COUNTER 1 COMPARE: Range: –2,147,483,648 to +2,147,483,647
MESSAGE
0
COUNTER 1 UP: Range: FlexLogic operand
MESSAGE
Off
COUNTER 1 DOWN: Range: FlexLogic operand
MESSAGE
Off
COUNTER 1 BLOCK: Range: FlexLogic operand
MESSAGE
Off
CNT1 SET TO PRESET: Range: FlexLogic operand
5 MESSAGE
Off
COUNTER 1 RESET: Range: FlexLogic operand
MESSAGE
Off
COUNT1 FREEZE/RESET: Range: FlexLogic operand
MESSAGE
Off
COUNT1 FREEZE/COUNT: Range: FlexLogic operand
MESSAGE
Off
There are 8 identical digital counters, numbered from 1 to 8. A digital counter counts the number of state transitions from
Logic 0 to Logic 1. The counter is used to count operations such as the pickups of an element, the changes of state of an
external contact (e.g. breaker auxiliary switch), or pulses from a watt-hour meter.
• COUNTER 1 UNITS: Assigns a label to identify the unit of measure pertaining to the digital transitions to be counted.
The units label will appear in the corresponding actual values status.
• COUNTER 1 PRESET: Sets the count to a required preset value before counting operations begin, as in the case
where a substitute relay is to be installed in place of an in-service relay, or while the counter is running.
• COUNTER 1 COMPARE: Sets the value to which the accumulated count value is compared. Three FlexLogic output
operands are provided to indicate if the present value is ‘more than (HI)’, ‘equal to (EQL)’, or ‘less than (LO)’ the set
value.
• COUNTER 1 UP: Selects the FlexLogic operand for incrementing the counter. If an enabled UP input is received when
the accumulated value is at the limit of +2,147,483,647 counts, the counter will rollover to –2,147,483,648.
• COUNTER 1 DOWN: Selects the FlexLogic operand for decrementing the counter. If an enabled DOWN input is
received when the accumulated value is at the limit of –2,147,483,648 counts, the counter will rollover to
+2,147,483,647.
• COUNTER 1 BLOCK: Selects the FlexLogic operand for blocking the counting operation. All counter operands are
blocked.

• CNT1 SET TO PRESET: Selects the FlexLogic operand used to set the count to the preset value. The counter will be
set to the preset value in the following situations:
1. When the counter is enabled and the CNT1 SET TO PRESET operand has the value 1 (when the counter is enabled
and CNT1 SET TO PRESET operand is 0, the counter will be set to 0).
2. When the counter is running and the CNT1 SET TO PRESET operand changes the state from 0 to 1 (CNT1 SET TO
PRESET changing from 1 to 0 while the counter is running has no effect on the count).
3. When a reset or reset/freeze command is sent to the counter and the CNT1 SET TO PRESET operand has the value
1 (when a reset or reset/freeze command is sent to the counter and the CNT1 SET TO PRESET operand has the
value 0, the counter will be set to 0).
• COUNTER 1 RESET: Selects the FlexLogic operand for setting the count to either “0” or the preset value depending
on the state of the CNT1 SET TO PRESET operand.
• COUNTER 1 FREEZE/RESET: Selects the FlexLogic operand for capturing (freezing) the accumulated count value
into a separate register with the date and time of the operation, and resetting the count to “0”.
• COUNTER 1 FREEZE/COUNT: Selects the FlexLogic operand for capturing (freezing) the accumulated count value
into a separate register with the date and time of the operation, and continuing counting. The present accumulated
value and captured frozen value with the associated date/time stamp are available as actual values. If control power is
interrupted, the accumulated and frozen values are saved into non-volatile memory during the power down operation.
SETTING
COUNTER 1 FUNCTION:
Disabled = 0
SETTINGS
Enabled = 1
COUNTER 1 NAME:
SETTING
COUNTER 1 UP:
AND COUNTER 1 UNITS:
COUNTER 1 PRESET:
RUN
5
Off = 0 SETTING
FLEXLOGIC
COUNTER 1 COMPARE: OPERANDS
SETTING
CALCULATE Count more than Comp. COUNTER 1 HI
COUNTER 1 DOWN: VALUE Count equal to Comp. COUNTER 1 EQL
Off = 0 Count less than Comp. COUNTER 1 LO
SETTING
COUNTER 1 BLOCK:
Off = 0 SET TO PRESET VALUE
SETTING SET TO ZERO

ACTUAL VALUE
CNT 1 SET TO PRESET: COUNTER 1 ACCUM:
Off = 0
AND
SETTING AND ACTUAL VALUES

COUNTER 1 RESET:
COUNTER 1 FROZEN:
Off = 0
OR STORE DATE & TIME Date & Time
SETTING
COUNT1 FREEZE/RESET:
Off = 0
OR
827065A1.VSD
SETTING
COUNT1 FREEZE/COUNT:
Off = 0
Figure 5–151: DIGITAL COUNTER SCHEME LOGIC

5.7.13 MONITORING ELEMENTS
a) MAIN MENU
PATH: SETTINGS  CONTROL ELEMENTS  MONITORING ELEMENTS
 MONITORING  BREAKER 1
See below.
 ELEMENTS  ARCING CURRENT
 BREAKER 2
MESSAGE See below.
 ARCING CURRENT
 BREAKER
 FLASHOVER 1
 BREAKER
 FLASHOVER 2
 BREAKER RESTRIKE 1

 BREAKER RESTRIKE 2

 VT FUSE FAILURE 1


5 MESSAGE

See page 5–292.

 OPEN POLE

 BROKEN CONDUCTOR 1

 BROKEN CONDUCTOR 2

 THERMAL OVERLOAD
 PROTECTION

b) BREAKER ARCING CURRENT

PATH: SETTINGS  CONTROL ELEMENTS  MONITORING ELEMENTS  BREAKER 1(4) ARCING CURRENT
 BREAKER 1 BKR 1 ARC AMP Range: Disabled, Enabled

 ARCING CURRENT FUNCTION: Disabled
BKR 1 ARC AMP Range: SRC 1, SRC 2, SRC 3, SRC 4
MESSAGE
SOURCE: SRC 1
BKR 1 ARC AMP INT-A: Range: FlexLogic operand
MESSAGE
Off
BKR 1 ARC AMP INT-B: Range: FlexLogic operand
MESSAGE
Off
BKR 1 ARC AMP INT-C: Range: FlexLogic operand
MESSAGE
Off
BKR 1 ARC AMP Range: 0.000 to 65.535 s in steps of 0.001
MESSAGE
DELAY: 0.000 s
BKR 1 ARC AMP LIMIT: Range: 0 to 50000 kA2-cycle in steps of 1
MESSAGE
1000 kA2-cyc
BKR 1 ARC AMP BLOCK: Range: FlexLogic operand
MESSAGE
Off
BKR 1 ARC AMP Range: Self-reset, Latched, Disabled
MESSAGE
TARGET: Self-reset
BKR 1 ARC AMP Range: Disabled, Enabled 5
MESSAGE
EVENTS: Disabled
There is one breaker arcing current element available per CT bank, with a minimum of two elements. This element calcu-
lates an estimate of the per-phase wear on the breaker contacts by measuring and integrating the current squared passing
through the breaker contacts as an arc. These per-phase values are added to accumulated totals for each phase and com-
pared to a programmed threshold value. When the threshold is exceeded in any phase, the relay can set an output operand
to “1”. The accumulated value for each phase can be displayed as an actual value.
The operation of the scheme is shown in the following logic diagram. The same output operand that is selected to operate
the output relay used to trip the breaker, indicating a tripping sequence has begun, is used to initiate this feature. A time
delay is introduced between initiation and the starting of integration to prevent integration of current flow through the
breaker before the contacts have parted. This interval includes the operating time of the output relay, any other auxiliary
relays and the breaker mechanism. For maximum measurement accuracy, the interval between change-of-state of the
operand (from 0 to 1) and contact separation should be measured for the specific installation. Integration of the measured
current continues for 100 ms, which is expected to include the total arcing period.
The feature is programmed to perform fault duration calculations. Fault duration is defined as a time between operation of
the disturbance detector occurring before initiation of this feature, and reset of an internal low-set overcurrent function. Cor-
rection is implemented to account for a non-zero reset time of the overcurrent function.
Breaker arcing currents and fault duration values are available under the ACTUAL VALUES  RECORDS  MAINTENANCE
 BREAKER 1(4) menus.
• BKR 1 ARC AMP INT-A(C): Select the same output operands that are configured to operate the output relays used to
trip the breaker. In three-pole tripping applications, the same operand should be configured to initiate arcing current
calculations for poles A, B and C of the breaker. In single-pole tripping applications, per-pole tripping operands should
be configured to initiate the calculations for the poles that are actually tripped.
• BKR 1 ARC AMP DELAY: This setting is used to program the delay interval between the time the tripping sequence is
initiated and the time the breaker contacts are expected to part, starting the integration of the measured current.
• BKR 1 ARC AMP LIMIT: Selects the threshold value above which the output operand is set.

Breaker
Contacts Arc
Initiate Part Extinguished
Total Area =
Breaker
Arcing
Current
(kA·cycle)
Programmable
Start Delay 100 ms
Start Stop
Integration Integration
Figure 5–152: ARCING CURRENT MEASUREMENT
SETTING
AND
BREAKER 1 ARCING
SETTING
AMP FUNCTION:
Enabled=1 BREAKER 1 ARCING
AMP DELAY: 100 ms
SETTING OR 0 0
BREAKER 1 ARCING
AMP BLOCK:
Off=0
5 SETTINGS
BREAKER 1 ARCING
AMP INIT-A:
AND
Off=0
BREAKER 1 ARCING
AMP INIT-B:
Off=0 OR
BREAKER 1 ARCING
AMP INIT-C:
Off=0
AND RUN
SETTING Integrate
BREAKER 1 ARCING Add to SETTING
AMP SOURCE: AND RUN Accumulator BREAKER 1 ARCING
IA IA 2-Cycle Select
AMP LIMIT: FLEXLOGIC OPERANDS
2
IB Integrate IB 2-Cycle Highest KA * Cycle Limit BKR1 ARC OP
IC IC 2-Cycle Value BKR1 ARC DPO
AND RUN
COMMAND
CLEAR BREAKER 1 Integrate ACTUAL VALUE

ARCING AMPS: Set All To Zero BKR 1 ARCING AMP FA
NO=0 BKR 1 ARCING AMP FB
YES=1 BKR 1 ARCING AMP FC
BKR 1 OPERATING TIME FA
BKR 1 OPERATING TIME FB
BKR 1 OPERATING TIME FC
BKR 1 OPERATING TIME 827071A4.CDR
Figure 5–153: BREAKER ARCING CURRENT SCHEME LOGIC

c) BREAKER FLASHOVER
PATH: SETTINGS  CONTROL ELEMENTS  MONITORING ELEMENTS  BREAKER FLASHOVER 1(4)
 BREAKER BKR 1 FLSHOVR Range: Disabled, Enabled

 FLASHOVER 1 FUNCTION: Disabled
BKR 1 FLSHOVR SIDE 1 Range: SRC 1, SRC 2, SRC 3, SRC 4
MESSAGE
SRC: SRC 1
BKR 1 FLSHOVR SIDE 2 Range: None, SRC 1, SRC 2, SRC 3, SRC 4
MESSAGE
SRC: None
BKR 1 STATUS CLSD A: Range: FlexLogic operand
MESSAGE
Off
BKR 1 STATUS CLSD B: Range: FlexLogic operand
MESSAGE
Off
BKR 1 STATUS CLSD C: Range: FlexLogic operand
MESSAGE
Off
BKR 1 FLSHOVR V PKP: Range: 0.000 to 1.500 pu in steps of 0.001
MESSAGE
0.850 pu
BKR 1 FLSHOVR DIFF V Range: 0 to 100000 V in steps of 1
MESSAGE
PKP: 1000 V
BKR 1 FLSHOVR AMP Range: 0.000 to 1.500 pu in steps of 0.001
MESSAGE
PKP: 0.600 pu
BKR 1 FLSHOVR PKP Range: 0.000 to 65.535 s in steps of 0.001 5
MESSAGE
DELAY: 0.100 s
BKR 1 FLSHOVR SPV A: Range: FlexLogic operand
MESSAGE
Off
BKR 1 FLSHOVR SPV B: Range: FlexLogic operand
MESSAGE
Off
BKR 1 FLSHOVR SPV C: Range: FlexLogic operand
MESSAGE
Off
BKR 1 FLSHOVR BLOCK: Range: FlexLogic operand
MESSAGE
Off
BKR 1 FLSHOVR Range: Self-reset, Latched, Disabled
MESSAGE
TARGET: Self-reset
BKR 1 FLSHOVR Range: Disabled, Enabled
MESSAGE
EVENTS: Disabled
The detection of the breaker flashover is based on the following condition:

1. Breaker open,
2. Voltage difference drop, and
3. Measured flashover current through the breaker.
Furthermore, the scheme is applicable for cases where either one or two sets of three-phase voltages are available across
the breaker.

THREE VT BREAKER FLASHOVER APPLICATION

When only one set of VTs is available across the breaker, the BRK 1 FLSHOVR SIDE 2 SRC setting should be “None”. To detect
an open breaker condition in this application, the scheme checks if the per-phase voltages were recovered (picked up), the
status of the breaker is open (contact input indicating the breaker status is off), and no flashover current is flowing. A con-
tact showing the breaker status must be provided to the relay. The voltage difference will not be considered as a condition
for open breaker in this part of the logic.
Voltages must be present prior to flashover conditions. If the three VTs are placed after the breaker on the line (or
feeder), and the downstream breaker is open, the measured voltage would be zero and the flashover element will
NOTE not be initiated.
The flashover detection will reset if the current drops back to zero, the breaker closes, or the selected FlexLogic operand
for supervision changes to high. Using supervision through the BRK 1 FLSHOVR SPV A, BRK 1 FLSHOVR SPV B, and BRK 1
FLSHOVR SPV C settings is recommended by selecting a trip operand that will not allow the flashover element to pickup prior
to the trip.
The flashover detection can be used for external alarm, re-tripping the breaker, or energizing the lockout relay.
Consider the following configuration:
Bus
CTs Breaker
Line/Feeder
5 Bus VTs
842746A1.CDR
The source 1 (SRC1) phase currents are feeder CTs and phase voltages are bus VTs, and Contact Input 1 is set as Breaker
52a contact. The conditions prior to flashover detection are:
1. 52a status = 0.
2. VAg, VBg, or VCg is greater than the pickup setting.
3. IA, IB, IC = 0; no current flows through the breaker.
4. VA is greater than pickup (not applicable in this scheme).
The conditions at flashover detection are:
1. 52a status = 0.
2. IA, IB, or IC is greater than the pickup current flowing through the breaker.
3. VA is greater than pickup (not applicable in this scheme).
SIX VT BREAKER FLASHOVER APPLICATION
The per-phase voltage difference approaches zero when the breaker is closed. The is well below any typical minimum
pickup voltage. Select the level of the BRK 1 FLSHOVR DIFF V PKP setting to be less than the voltage difference measured
across the breaker when the close or open breaker resistors are left in service. Prior to flashover, the voltage difference is
larger than BRK 1 FLSHOVR DIFF V PKP. This applies to either the difference between two live voltages per phase or when the
voltage from one side of the breaker has dropped to zero (line de-energized), at least one per-phase voltage is larger than
the BRK 1 FLSHOVR V PKP setting, and no current flows through the breaker poles. During breaker flashover, the per-phase
voltages from both sides of the breaker drops below the pickup value defined by the BRK 1 FLSHOVR V PKP setting, the volt-
age difference drops below the pickup setting, and flashover current is detected. These flashover conditions initiate Flex-
Logic pickup operands and start the BRK 1 FLSHOVR PKP DELAY timer.
This application does not require detection of breaker status via a 52a contact, as it uses a voltage difference larger than
the BRK 1 FLSHOVR DIFF V PKP setting. However, monitoring the breaker contact will ensure scheme stability.

Consider the following configuration:
Bus
CTs Breaker
Line/Feeder
VTs
VTs
842745A1.CDR
The source 1 (SRC1) phase currents are CTs and phase voltages are bus VTs. The source 2 (SRC2) phase voltages are
line VTs. Contact input 1 is set as the breaker 52a contact (optional).
The conditions prior to flashover detection are:
1. VA is greater than pickup
2. IA, IB, IC = 0; no current flows through the breaker
3. 52a status = 0 (optional)
The conditions at flashover detection are:
1. VA is less than pickup
2. VAg, VBg, or VCg is lower than the pickup setting
3. IA, IB, or IC is greater than the pickup current flowing through the breaker
4. 52a status = 0 (optional)
5
The element is operational only when phase-to-ground voltages are connected to relay terminals. The flashover
element will not operate if delta voltages are applied.
NOTE
The breaker flashover settings are described below.

• BRK 1 FLSHOVR SIDE 1 SRC: This setting specifies a signal source used to provide three-phase voltages and three-
phase currents from one side of the current breaker. The source selected as a setting and must be configured with
breaker phase voltages and currents, even if only three (3) VTs are available across the breaker.
• BRK 1 FLSHOVR SIDE 2 SRC: This setting specifies a signal source used to provide another set of three phase volt-
ages whenever six (6) VTs are available across the breaker.
• BRK 1 STATUS CLSD A to BRK 1 STATUS CLSD C: These settings specify FlexLogic operands to indicate the open
status of the breaker. A separate FlexLogic operand can be selected to detect individual breaker pole status and pro-
vide flashover detection. The recommended setting is 52a breaker contact or another operand defining the breaker
poles open status.
• BRK 1 FLSHOVR V PKP: This setting specifies a pickup level for the phase voltages from both sides of the breaker. If
six VTs are available, opening the breaker leads to two possible combinations – live voltages from only one side of the
breaker, or live voltages from both sides of the breaker. Either case will set the scheme ready for flashover detection
upon detection of voltage above the selected value. Set BRK FLSHOVR V PKP to 85 to 90% of the nominal voltage.
• BRK 1 FLSHOVR DIFF V PKP: This setting specifies a pickup level for the phase voltage difference when two VTs per
phase are available across the breaker. The pickup voltage difference should be below the monitored voltage differ-
ence when close or open breaker resistors are left in service. The setting is selected as primary volts difference
between the sources.
• BRK 1 FLSHOVR AMP PKP: This setting specifies the normal load current which can flow through the breaker.
Depending on the flashover protection application, the flashover current can vary from levels of the charging current
when the line is de-energized (all line breakers open), to well above the maximum line (feeder) load (line/feeder con-
nected to load).
• BRK 1 FLSHOVR SPV A to BRK 1 FLSHOVR SPV C: These settings specify FlexLogic operands (per breaker pole)
that supervise the operation of the element per phase. Supervision can be provided by operation of other protection

elements, breaker failure, and close and trip commands. A six-cycle time delay applies after the selected FlexLogic
operand resets.
• BRK FLSHOVR PKP DELAY: This setting specifies the time delay to operate after a pickup condition is detected.
SETTINGS
BRK 1 FLSHOVR SUPV A:

0
FlexLogic operand: Off=0
6 cycle
BRK 1 FLSHOVR SUPV B: Phase B
logic
FlexLogic operand: Off=0
BRK 1 FLSHOVR SUPV C: Phase C

logic FLEXLOGIC OPERANDS
FlexLogic operand: Off=0 BRK 1 FLSHOVR PKP A FLEXLOGIC OPERANDS
BRK 1 FLSHOVR PKP B OR BRK 1 FLSHOVR PKP
SETTING
SETTING BRK 1 FLSHOVR PKP C BRK 1 FLSHOVR DPO
BREAKER FLASHOVER
FUNCTION: BRK 1 FLSHOVR V PKP:
FLEXLOGIC OPERANDS
Enable=1
AND RUN BRK 1 FLSHOVR DPO A
Block: OFF=0
VA > PKP BRK 1 FLSHOVR DPO B
0 AND BRK 1 FLSHOVR DPO C
OR SET
5 cycle
dominant
Va > PKP Phase C logic
Phase B logic
RESET
SETTINGS
5 cycle
BRK 1 STATUS CLSD A:
0 OR
SET SETTING
RUN dominant
BRK 1 FLSHOVR PKP
FlexLogic operand: On=1
DELAY:
FLEXLOGIC OPERANDS
BRK 1 STATUS CLSD B: Phase B tPKP
logic 0 BRK 1 FLSHOVR OP A
RUN
FLEXLOGIC OPERAND
FlexLogic operand: On=1
Phase B logic BRK 1 FLSHOVR OP B OR BRK 1 FLSHOVR OP
BRK 1 STATUS CLSD C: Phase C RESET
logic OR Phase C logic BRK 1 FLSHOVR OP C
SETTINGS RUN
BRK 1 FLSHOVR SIDE 1 FlexLogic operand: On=1
SRC:
SRC 1, SRC 2, … , SRC 6 SETTING
VA
BRK 1 FLSHOVR AMP PKP:
VB
VC RUN
IA IA > PKP
IB
AND
IC
5
SETTINGS
SETTING
BRK 1 FLSHOVR SIDE 2
SRC: BRK 1 FLSHOVR DIFF V
PKP:
SRC 1, SRC 2, … , SRC 6, none
RUN
Va ΔVA > PKP
ΔVA = | VA - Va |
Vb
Vc 842018A2.CDR
Figure 5–154: BREAKER FLASHOVER SCHEME LOGIC

d) BREAKER RESTRIKE
PATH: SETTINGS  CONTROL ELEMENTS  MONITORING ELEMENTS  BREAKER RESTRIKE 1(2)
 BREAKER RESTRIKE 1 BREAKER RESTRIKE 1 Range: Disabled, Enabled

BKR RSTR 1 BLOCK: Range: FlexLogic operand
MESSAGE
Off
BREAKER RESTRIKE 1 Range: SRC 1, SRC 2, SRC 3, SRC 4
MESSAGE
SOURCE: SRC 1
BREAKER RESTRIKE 1 Range: 0.10 to 2.00 pu in steps of 0.01
MESSAGE
PICKUP: 0.500 pu
BREAKER RESTRIKE 1 Range: 0.000 to 65.535 s in steps of 0.001
MESSAGE
RESET DELAY: 0.100 s
BKR RSTR 1 BKR OPEN: Range: FlexLogic operand
MESSAGE
Off
BKR RSTR 1 OPEN CMD: Range: FlexLogic operand
MESSAGE
Off
BKR RSTR 1 CLS CMD: Range: FlexLogic operand
MESSAGE
Off
BREAKER RESTRIKE 1 Range: Self-reset, Latched, Disabled
MESSAGE
TARGET: Self-reset
BREAKER RESTRIKE 1 Range: Disabled, Enabled 5
MESSAGE
EVENTS: Disabled
According to IEEE standard C37.100: IEEE Standard Definitions for Power Switchgear, restrike is defined as “a resumption
of current between the contacts of a switching device during an opening operation after an interval of zero current of
¼ cycle at normal frequency or longer”.
10
8
6
4
current (amps)
2
0.01 0.03
0 time (ms)
0.02 0.05
–2
–4
–6
–8
OPERATE
–10
834764A1.CDR
Figure 5–155: TYPICAL RESTRIKE WAVEFORM AND DETECTION FLAG

The breaker restrike algorithm responds to a successful interruption of the phase current following a declaration of capaci-
tor bank offline as per the breaker pole indication. If a high-frequency current with a magnitude greater than the threshold is
resumed at least ¼ of a cycle later than the phase current interruption, then a breaker restrike condition is declared in the
corresponding phase and the BRK RESTRIKE 1 OP operand is asserted for a short period of time. The user can add coun-
ters and other logic to facilitate the decision making process as to the appropriate actions upon detecting a single restrike or
a series of consecutive restrikes.
A restrike event (FlexLogic operand) is declared if all of the following hold:
• The current is initially interrupted.

• The breaker status is open.

• An elevated high frequency current condition occurs and the current subsequently drops out again.
The algorithm is illustrated in the state machine diagram shown below.
Breaker open
command or breaker
open state
Capacitor bank
offline
Breaker
close
Current
Capacitor bank
interruption
Breaker online
(overcurrent)
close
High-frequency
elevated current Breaker close
Current
interruption
5 (overcurrent)
Restrike detected:
OP state asserted
834768A1.CDR
Figure 5–156: ALGORITHM ILLUSTRATION – STATE MACHINE TO DETECT RESTRIKE

In this way, a distinction is made between a self-extinguishing restrike and permanent breaker failure condition. The latter
can be detected by the breaker failure function or a regular instantaneous overcurrent element. Also, a fast succession of
restrikes will be picked up by breaker failure or instantaneous overcurrent protection.
The following settings are available for each element.
• BREAKER RESTRIKE 1 FUNCTION: This setting enable and disables operation of the breaker restrike detection ele-
ment.
• BRK RSTR 1 BLOCK: This setting is used to block operation of the breaker restrike detection element.
• BREAKER RESTRIKE 1 SOURCE: This setting selects the source of the current for this element. This source must
have a valid CT bank assigned.
• BREAKER RESTRIKE 1 PICKUP: This setting specifies the pickup level of the overcurrent detector in per-unit values
of CT nominal current.
• BREAKER RESTRIKE 1 RESET DELAY: This setting specifies the reset delay for this element. When set to “0 ms”,
then FlexLogic operand will be picked up for only 1/8th of the power cycle.
• BRK RSTR 1 BRK OPEN: This setting assigns a FlexLogic operand indicating the open position of the breaker. It must
be logic “1” when breaker is open.
• BRK RSTR 1 OPEN CMD: This setting assigns a FlexLogic operand indicating a breaker open command. It must be
logic “1” when breaker is opened, either manually or from protection logic.
• BRK RSTR 1 CLS CMD: This setting assigns a FlexLogic operand indicating a breaker close command. It must be
logic “1” when breaker is closed.

SETTING
BREAKER RESTRIKE 1
FUNCTION
= Enabled
SETTING AND
BKR RSTR 1 BLK
= Off SETTING SETTING
BREAKER RESTRIKE 1 PICKUP BREAKER RESTRIKE 1
RUN RESET DELAY
SETTING 0
BREAKER RESTRIKE 1 RUN Restrike detection logic
SOURCE ARMED TRST
Current interruption
= IA detection logic 0
FLEXLOGIC OPERANDS
= IB
Imag < 0.05 pu TRST BKR RESTRIKE 1 OP A
= IC
for t > ¼ cycle 0 BKR RESTRIKE 1 OP B
BKR RESTRIKE 1 OP C
SETTING RESET TRST
BKR RSTR 1 BKR OPEN
= Off
FLEXLOGIC OPERAND
OR BKR RESTRIKE 1 OP
SETTING OR
BKR RSTR 1 OPEN CMD
= Off
AND
SETTING
BKR RSTR 1 CLS CMD
= Off 834012A1.CDR
Figure 5–157: BREAKER RESTRIKE SCHEME LOGIC

e) VT FUSE FAILURE
PATH: SETTINGS  CONTROL ELEMENTS  MONITORING ELEMENTS  VT FUSE FAILURE 1(4)
 VT FUSE FAILURE 1 VT FUSE FAILURE 1 Range: Disabled, Enabled

 NEUTRAL WIRE OPEN 1 Range: Disabled, Enabled
MESSAGE
 DETECTION: Disabled
 NEUTRAL WIRE OPEN 1 0.000 to 3.000 pu in steps of 0.001
MESSAGE
 3 HARM PKP: 0.100
Every signal source includes a fuse failure scheme.

The VT fuse failure detector can be used to raise an alarm and/or block elements that may operate incorrectly for a full or
partial loss of AC potential caused by one or more blown fuses. Some elements that might be blocked (via the BLOCK input)
are distance, voltage restrained overcurrent, and directional current.
There are two classes of fuse failure that occur:
• Class A: loss of one or two phases.
• Class B: loss of all three phases.
Different means of detection are required for each class. An indication of class A failures is a significant level of negative-
sequence voltage, whereas an indication of class B failures is when positive sequence current is present and there is an
insignificant amount of positive sequence voltage. Also rapid decrease in the phase voltages magnitude from a healthy
voltage level without disturbance in current can indicate a VT fuse fail conditions. These noted indications of fuse failure
can also be present when faults are present on the system, so a means of detecting faults and inhibiting fuse failure decla-
5 rations during these events is provided.

Once the fuse failure condition is declared, it is sealed-in until the cause that generated it disappears.
An additional condition is introduced to inhibit a fuse failure declaration when the monitored circuit is de-energized; positive-
sequence voltage and current are both below threshold levels.
The VT FUSE FAILURE 1 FUNCTION setting enables and disables the fuse failure feature for each source.
The VT NEU WIRE OPEN 1 FUNCTION setting enables and disables the VT neutral wire open detection function. When the
VT is connected in Delta, do not enabled this function because there is no neutral wire for Delta connected VT.
The VT NEU WIRE OPEN 1 3 HRAM PKP setting specifies the pickup level of 3rd harmonic of 3V0 signal for the VT NEU
WIRE OPEN detection logic to pick up.

SETTING VA, VB and VC are the

Function voltage magnitude of one OR
Enabled = 1 cycle before
AND
COMPARATORS FAULT
Run
|VA|-|VA| > 0.2 pu
& |VA| > 0.8 pu
Run
|VB|-|VB| > 0.2 pu OR
SOURCE 1 & |VB| > 0.8 pu
VA Run
|VC|-|VC| > 0.2 pu
VB & |VC| > 0.8 pu
VC Run
V_2 V_2 > 0.1 pu OR
V_1 Run FUSE

V_1 < 0.05 pu FAIL
I_1
Run AND
I_1 > 0.075 pu
TIMER OR
Run 2 cycles SET
TIMER AND
V_1 < 0.80 pu 0
2 cycles
FLEXLOGIC OPERANDS
Run AND
I_1 < 0.05 pu Latch SRC1 VT FUSE FAIL OP
20 cycles
SRC1 VT FUSE FAIL DPO
FLEXLOGIC OPERANDS
SRC1 50DD OP
OPEN POLE OP
The OPEN POLE OP operand applies
to the D60, L60, and L90 AND
TIMER
OR 30 cycles
RESET
0
AND Reset-dominant
FLEXLOGIC OPERAND
AND SRC1 VT FUSE FAIL VOL LOSS
SETTING
AND
TIMER
5 cycles
5
3 HARM PKP
0
AND Run FLEXLOGIC OPERAND
SETTING 3V_0 3rd Harm >setting OR SRC1 VT NEU WIRE OPEN
TIMER
Neutral Wire Open Detect
0
Enabled = 1
AND 20 cycles
SOURCE 1 FLEX-ANALOG
3V_0 (3rd Harmonic) SRC1 3V0 3nd Harmonic
827093AQ.CDR
Figure 5–158: VT FUSE FAIL SCHEME LOGIC

Base voltage for this element is PHASE VT SECONDARY setting in the case of WYE VTs and (PHASE VT SECONDARY)/
3 in case of DELTA VTs.

f) OPEN POLE DETECTOR

PATH: SETTINGS  CONTROL ELEMENTS  MONITORING ELEMENTS  OPEN POLE
 OPEN POLE OPEN POLE FUNCTION: Range: Disabled, Enabled

 Disabled
OPEN POLE BLOCK: Range: FlexLogic operand
MESSAGE
Off
OPEN POLE VOLTAGE Range: Disabled, Enabled
MESSAGE
SUPV: Disabled
OPEN POLE CURRENT Range: 0.000 to 30.000 pu in steps of 0.001
MESSAGE
PKP: 0.050 pu
OPEN POLE LINE XC1: Range: 300.0 to 9999.9 ohms in steps of 0.001
MESSAGE
9999.9 Ω
OPEN POLE LINE XC0: Range: 300.0 to 9999.9 ohms in steps of 0.001
MESSAGE
9999.9 Ω
OPEN POLE REM CURR Range: 0.000 to 30.000 pu in steps of 0.001
MESSAGE
PKP: 0.050 pu
OPEN POLE MODE: Range: Accelerated, Traditional
MESSAGE
Accelerated
OPEN POLE DETECTION: Range: I AND V AND CBaux, I AND V only
MESSAGE
I AND V AND CBaux
5 OPEN POLE TARGET: Range: Self-Reset, Latched, Disabled
MESSAGE
Self-Reset
OPEN POLE EVENTS: Range: Enabled, Disabled
MESSAGE
Disabled
The open pole detector is intended to identify an open pole of the line circuit breaker. The scheme monitors the breakers
auxiliary contacts, current in the circuit and optionally voltage on the line. The scheme generates output operands used to
block the phase selector and some specific protection elements, thus preventing maloperation during the dead time of a
single-pole autoreclose cycle or any other open pole conditions.
The scheme declares an open pole at the moment a single-pole trip is issued.
In two-breaker and breaker-and-a-half applications, an open pole condition is declared when one or more of the following
hold:
• Both breakers have an open pole on the same phase.
• The current on the line drops below a threshold.
• The current and voltage on the line drop below a threshold.
The open pole feature uses signals defined by the GROUPED ELEMENTS  SETTING GROUP 1(6)  DISTANCE  DISTANCE
SOURCE setting. Voltage supervision can be used only with wye VTs on the line side of the breaker.
The OPEN POLE CURRENT PICKUP setting establishes the current threshold below which an open pole is declared.
The OPEN POLE LINE XC1 setting specifies positive-sequence reactance of the entire line. If shunt reactors are applied, this
value should be a net capacitive reactance of the line and the reactors installed between the line breakers. The value is
entered in secondary ohms. This setting is relevant if open pole condition at the remote end of the line is to be sensed and
utilized by the relay.
The OPEN POLE LINE XC0 setting specifies zero-sequence reactance of the entire line. If shunt reactors are applied, this
value should be a net capacitive reactance of the line and the reactors installed between the line breakers. The value shall
be entered in secondary ohms. This setting is relevant if open pole condition at the remote end of the line is to be sensed
and utilized by the relay (OPEN POLE REM OP FlexLogic operand).

The OPEN POLE REM CURR PKP setting specifies pickup level for the remote-end current estimated by the relay as the local
current compensated by the calculated charging current. The latter is calculated based on the local voltages and the capac-
itive reactances of the line. This setting is relevant if open pole condition at the remote end of the line is to be sensed and
utilized by the relay (OPEN POLE REM OP FlexLogic operand).
The OPEN POLE MODE setting selects the mode of operation of the open pole function. When the “Accelerated” mode is cho-
sen, an open pole will be declared ½ cycle after trip output operation and before the breaker pole opens. This blocks dis-
tance loops involved in the faulted phase and phase selector, and arms the trip output to produce three-pole trip for the next
fault. If the fault evolves into multi-phase fault before breaker pole opens for the first fault, the remaining in-service distance
loops would initiate a three-pole trip. When the “Traditional” mode is selected, then an open pole is declared only after the
breaker opens and current disappears. If the fault evolves into a multi-phase fault before the circuit breaker pole opens for
the first fault, the phase selector will change the fault type from a single-line-to-ground fault to a multi-phase fault, thereby
initiating a three-pole trip.
The OPEN POLE DETECTION setting selects the signals used to detect an open pole condition. When “I AND V AND CBaux”
value is selected, the breaker 52 contacts and the current with optional voltage signals are used to determine open pole
conditions. For the “I AND V only” selection, only the current with optional voltage signals are used.
For convenience, the position of the breaker poles defined in the breaker control feature and available as FlexLogic oper-
and BREAKER 1 ΦA CLSD through BREAKER 1 ΦC CLSD and BREAKER 1 OOS are used by the open pole feature if the “I AND
V AND CBaux” detection value is selected.
For correct operation of the open pole detector, the breaker control, trip output, and single-pole autoreclose features must
be enabled and configured properly. When used in configuration with only one breaker, the BREAKER 2 FUNCTION should be
“Enabled” and the BREAKER 2 OUT OF SV setting should be “On” (refer to the Breaker Control section earlier in this chapter
for additional details).

Figure 5–159: OPEN POLE DETECTOR LOGIC (Sheet 1 of 2)

Figure 5–160: OPEN POLE DETECTOR LOGIC (Sheet 2 of 2)
g) BROKEN CONDUCTOR DETECTION

PATH: SETTINGS  CONTROL ELEMENTS  MONITORING ELEMENTS  BROKEN CONDUCTOR 1(2) 5
 BROKEN CONDUCTOR 1 BROKEN CONDUCTOR 1 Range: Disabled, Enabled
BROKEN CONDUCTOR 1 Range: SRC 1, SRC 2, SRC 3, SRC 4
MESSAGE
SOURCE: SRC 1
BROKEN CONDUCTOR 1 Range: 20.0% to 100.0% in steps of 0.1%
MESSAGE
I2/I1 RATIO: 20%
BROKEN CONDUCTOR 1 Range: 0.05 to 1.00 pu in steps of 0.01
MESSAGE
I1 MIN: 0.10 pu
BROKEN CONDUCTOR 1 Range: 0.05 to 5.00 pu in steps of 0.01
MESSAGE
I1 MAX: 1.50 pu
BROKEN CONDUCTOR 1 Range: 0.000 to 65.535 s in steps of 0.001
MESSAGE
PKP DELAY: 20.000 s
BROKEN CONDCT 1 BLK: Range: FlexLogic operand
MESSAGE
Off
BROKEN CONDUCT 1 Range: Self-reset, Latched, Disabled
MESSAGE
TARGET: Self-reset
BROKEN CONDUCT 1 Range: Disabled, Enabled
MESSAGE
EVENTS: Disabled
Two broken conductor detection elements are provided.

The broken conductor function will detect a transmission line broken conductor condition or a single-pole breaker malfunc-
tion condition through checking the phase current input signals and the I_2 / I_1 ratio. The intention of this function is to
detect a single-phase broken conductor only. As such two-phase or three-phase broken conductors cannot be detected.

To distinguish between single-phase disappearance and system disturbance in all three phases (such as load change,
switching, etc.), the broken conductor element monitors the change in all three phase currents at the present instance and
at four cycles previous. It also monitors changes in the I_2 / I_1 ratio, I_1 minimum, and I_1 maximum.
The broken conductor function should not be used to respond to fault transients and single-pole tripping/reclosing condi-
tions. Therefore, the time delay should be programmed to a sufficient length to ensure coordination with the breaker dead
time of the recloser function.
• BROKEN CONDUCTOR 1 FUNCTION: This setting enables and disables the broken conductor function.
• BROKEN CONDUCTOR 1 SOURCE: This setting selects a signal source used to provide three-phase current inputs
to this function.
• BROKEN CONDUCTOR 1 I2/I1 RATIO: This setting specifies the ratio of negative-sequence current to positive-
sequence current. When one phase conductor is broken, the I_2 / I_1 ratio with a balanced remaining two phases is
50%. So normally this setting should be set below 50% (for example, to 30%).
• BROKEN CONDUCTOR 1 I1 MIN: This setting specifies the minimum positive-sequence current supervision level.
Ensure this setting is programmed to a sufficient level to prevent I_2 / I_1 from erratic pickup due to a low I_1 signal.
However, this setting should not be set too high, since the broken conductor condition cannot be detected under light
load conditions when I_1 is less than the value specified by this setting.
• BROKEN CONDUCTOR 1 I1 MAX: This setting specifies the maximum I_1 level allowed for the broken conductor
function to operate. When I_1 exceeds this setting, this it is considered a fault. This broken conductor function should
not respond to any fault conditions, so normally this setting is programmed to less than the maximum load current.
• BROKEN CONDUCTOR 1 PKP DELAY: This setting specifies the pickup time delay for this function to operate after
assertion of the broken conductor pickup FlexLogic operand.
5 SETTINGS
BROKEN CONDUCTOR 1
FUNCTION:
Enabled = 1
AND
BROKEN CONDCT 1 BLK:

SETTING
Off = 0
BROKEN CONDUCTOR 1
I1 MAX :
SETTINGS SETTING BROKEN CONDUCTOR 1

I2/I1 RATIO :
BROKEN CONDUCTOR 1 BROKEN CONDUCTOR 1
RUN
SOURCE: I1 MIN : SETTING
I2 RUN | I1 | < I1 MAX
| I2 | / | I1 |> RATIO BROKEN CONDUCTOR 1
I1 | I1 | > I1 MIN I1 MAX :
FLEXLOGIC OPERAND
Ia | Ia | < I1 MIN
tPKP
BROKEN CONDUCT 1 OP
AND
AND
Ib | Ib | < I1 MIN
0
Ic | Ic | < I1 MIN
| Ia’ | - | Ia | > 0.05pu
| Ib’ | - | Ib | > 0.05pu
2 cyc
AND
OR
| Ic’ | - | Ic | > 0.05pu

0
OR
FLEXLOGIC OPERAND
BROKEN CONDUCT 1 PKP
AND
One phase current loss

detection
Figure 5–161: BROKEN CONDUCTOR DETECTION LOGIC

h) THERMAL OVERLOAD PROTECTION

PATH: SETTINGS  CONTROL ELEMENTS  MONITORING ELEMENTS  THERMAL OVERLOAD PROTECTION  THERMAL
PROTECTION 1(2)
 THERMAL THERMAL PROTECTION 1 Range: Disabled, Enabled

 PROTECTION 1 FUNCTION: Disabled
THERMAL PROTECTION 1 Range: SRC 1, SRC 2, SRC 3, SRC 4
MESSAGE
SOURCE: SRC1
THERMAL PROTECTION 1 Range: 0.20 to 3.00 pu in steps of 0.01
MESSAGE
BASE CURR: 0.80 pu
THERMAL PROTECTION 1 Range: 1.00 to 1.20 in steps of 0.05
MESSAGE
k FACTOR: 1.10
THERM PROT 1 TRIP Range: 0 to 1000 min. in steps of 1
MESSAGE
TIME CONST: 45 min.
THERM PROT 1 RESET Range: 0 to 1000 min. in steps of 1
MESSAGE
TIME CONST: 45 min.
THERM PROT 1 MINIM Range: 0 to 1000 min. in steps of 1
MESSAGE
RESET TIME: 20 min.
THERM PROT 1 RESET: Range: FlexLogic operand
MESSAGE
Off
THERM PROT 1 BLOCK: Range: FlexLogic operand
MESSAGE
Off 5
THERMAL PROTECTION 1 Range: Self-reset, Latched, Disabled
MESSAGE
TARGET: Self-reset
THERMAL PROTECTION 1 Range: Disabled, Enabled
MESSAGE
EVENTS: Disabled
The thermal overload protection element corresponds to the IEC 255-8 standard and is used to detect thermal overload
conditions in protected power system elements. Choosing an appropriate time constant element can be used to protect dif-
ferent elements of the power system. The cold curve characteristic is applied when the previous averaged load current over
the last 5 cycles is less than 10% of the base current. If this current is greater or equal than 10% than the base current, then
the hot curve characteristic is applied.
The IEC255-8 cold curve is defined as follows:
 2 
I
t op =  op  ln  -------------------------
2
-
2
(EQ 5.27)
 I –  kI B  
The IEC255-8 hot curve is defined as follows:

2 2
 I – Ip 
t op =  op  ln  -------------------------
- (EQ 5.28)
 I 2 –  kI B  2
In the above equations,

• top = time to operate.
• τop = thermal protection trip time constant.
• I = measured overload RMS current.
• Ip = measured load RMS current before overload occurs.
• k= IEC 255-8 k-factor applied to IB, defining maximum permissible current above nominal current.
• IB = protected element base (nominal) current.

The reset time of the thermal overload protection element is also time delayed using following formula:
2
  kI B  
t rst =  rst  ln  ----------------------------
2 2
- + T min (EQ 5.29)
 I –  kI B  
In the above equation,

• τrst = thermal protection trip time constant.
• Tmin is a minimum reset time setting

7PLQ

ƌUVW
ƌRS
5
W PLQ

,,SNS
$&'5
Figure 5–162: IEC 255-8 SAMPLE OPERATE AND RESET CURVES

The thermal overload protection element estimates accumulated thermal energy E using the following equations calculated
each power cycle. When current is greater than the pickup level, In > k × IB, element starts increasing the thermal energy:
t
E n = E n – 1 + --------------- (EQ 5.30)
t op  In 
When current is less than the dropout level, In > 0.97 × k × IB, the element starts decreasing the thermal energy:

t
E n = E n – 1 – --------------- (EQ 5.31)
t rst  In 
In the above equations,

• Δt is the power cycle duration.
• n is the power cycle index.
• top(In) is the trip time calculated at index n as per the IEC255-8 cold curve or hot curve equations.
• trst(In) is the reset time calculated at index n as per the reset time equation.
• In is the measured overload RMS current at index n.
• En is the accumulated energy at index n.
• En – 1 is the accumulated energy at index n – 1.
The thermal overload protection element removes the THERMAL PROT 1 OP output operand when E < 0.05. In case of
emergency, the thermal memory and THERMAL PROT 1 OP output operand can be reset using THERM PROT 1 RESET setting.
All calculations are performed per phase. If the accumulated energy reaches value 1 in any phase, the thermal overload
protection element operates and only resets when energy is less than 0.05 in all three phases.
Table 5–33: TYPICAL TIME CONSTANTS

PROTECTED EQUIPMENT TIME CONSTANT MINIMUM RESET TIME
Capacitor bank 10 minutes 30 minutes
Overhead line 10 minutes 20 minutes
Air-core reactor 40 minutes 30 minutes
Busbar 60 minutes 20 minutes 5
Underground cable 20 to 60 minutes 60 minutes
The logic for the thermal overload protection element is shown below.
6(77,1*6
)XQFWLRQ
(QDEOHG
%ORFN $1'
2II
6(77,1*6 )/(;/2*,&23(5$1'
6(77,1* %DVH&XUUHQW $1' 7+(50$/35273.3
6RXUFH .)DFWRU
,$506 ,$!Nî,E 6(77,1*
,%506 ,%!Nî,E 25 7ULS7LPH&RQVWDQW
,&506 ,&!Nî,F 581
(! 6 )/(;/2*,&23(5$1'
/DWFK 7+(50$/352723
5
5HVHWGRPLQDQW
6(77,1*6
5HVHW7LPH&RQVWDQW
0LQLPXP5HVHW7LPH
581
(
6(77,1*
5HVHW
2II 5HVHW(WR $&'5
Figure 5–163: THERMAL OVERLOAD PROTECTION SCHEME LOGIC

5.7.14 PILOT SCHEMES
a) MAIN MENU
PATH: SETTINGS  CONTROL ELEMENTS  PILOT SCHEMES
 PILOT SCHEMES  DUTT SCHEME

See page 5–302.
 
 PUTT SCHEME

 POTT SCHEME

 POTT1 SCHEME

 HYBRID POTT SCHEME

 BLOCKING SCHEME

 DCUB SCHEME

This menu contains settings for selecting and configuring protection signaling schemes. All schemes are available for sin-
gle-pole tripping applications and can be used with one, two, or four-bit communications channels. Choices of communica-
5 tions channels include remote inputs/outputs and telecommunications interfaces.
b) DIRECT UNDER-REACHING TRANSFER TRIP (DUTT)

PATH: SETTINGS  CONTROL ELEMENTS  PILOT SCHEMES  DUTT SCHEME
 DUTT SCHEME DUTT SCHEME Range: Disabled, Enabled

DUTT SCHEME BLOCK: Range: FlexLogic operand
MESSAGE
Off
DUTT SEAL-IN Range: 0.000 to 65.535 s in steps of 0.001
MESSAGE
DELAY: 0.010 s
DUTT NO OF COMM Range: 1, 2, or 4
MESSAGE
BITS: 1
DUTT RX1: Range: FlexLogic operand
MESSAGE
Off
MESSAGE
Off
MESSAGE
Off
MESSAGE
Off
DUTT SCHEME TARGET: Range: Self-Reset, Latched, Disabled
MESSAGE
Self-Reset
DUTT SCHEME EVENTS: Range: Disabled, Enabled
MESSAGE
Disabled

This scheme uses an under-reaching Zone 1 distance element to key a transfer trip signal(s) to the remote end(s), where
on receipt, the DUTT pilot scheme operates without additional protection supervision. For proper operation of the scheme
the Zone 1 phase and ground distance elements must be enabled, configured, and set per rules of distance relaying.
In single-pole tripping applications, the scheme uses local fault type identification provided by the Phase Selector together
with information received from the remote terminal(s). The latter may be coded into one, two or four bits over the communi-
cations channel.
The scheme generates output operands (DUTT TX1 through DUTT TX4) that are used to transmit the direct under-reaching
signals to the remote end(s). Choices of communications channel include remote inputs/outputs and telecommunications
interfaces. When used with telecommunications facilities the output operands should be assigned to operate output con-
tacts connected to assert the individual bits at the interface.
To make the scheme a fully operational stand-alone feature, the scheme output operands must be configured to interface
with other relay functions, output contacts in particular. Typically, the output operands should be programmed to initiate a
trip, breaker fail, and autoreclose, and drive a user-programmable LED as per user application. When used in conjunction
with the trip output element, the scheme is pre-configured to initiate trip, breaker fail, and single-pole autoreclose actions.
• DUTT SCHEME BLOCK: This setting allows the user to assign any FlexLogic operand to block the scheme. Contact
inputs from a pilot cut-out switch are typically used for this purpose.
• DUTT SEAL-IN DELAY: The output FlexLogic operand (DUTT OP) is produced according to the DUTT scheme logic. A
seal-in time delay is applied to this operand for coping with noisy communication channels such as a power line carrier.
The DUTT SEAL-IN DELAY is a minimum guaranteed duration of the DUTT OP pulse. As this operand activates the Trip
Table of the DUTT scheme, the trip operands DUTT TRIP A, B, C and 3P are sealed-in for the same period of time.
• DUTT NO OF COMM BITS: This setting specifies the number of bits available on the communications channel. With
only one bit available, the scheme sends the direct under-reaching transfer trip command on bit no.1 (DUTT TX1 oper-
and) and responds to the direct trip command received on bit no. 1 (DUTT RX1 setting). The scheme uses only local
fault type identification provided by the Phase Selector to assert the output operands DUTT TRIP A, B, C and 3P (see 5
Chapter 8: Theory of Operation for details on the use of communication channels).
• DUTT RX1 through DUTT RX4: These settings allow the user to select the FlexLogic operands that represent the
receive signals for the scheme. Typically input contacts interfacing with a signaling system are used.
The DUTT scheme requires a secure and dependable signaling system. For this reason, a series/parallel combination
of receive signal “contacts” is often used. This is accomplished by using a multi-bit communications system to transmit
redundant copies of the TX signal (often via different paths) and building appropriate security logic (such as series
(AND gate) or 2-out-of-3 voting logic) with FlexLogic. The DUTT RX1(4) settings should be associated with the final
(secure) TX signals.

In single-bit applications, DUTT RX1 must be used. In two-bit applications, DUTT RX1 and DUTT RX2 must be used. In
four-bit applications, DUTT RX1, DUTT RX2, DUTT RX3, and DUTT RX4 must be used. In multi-terminal applications, the RX
signals from two or more remote terminals should be connected through OR gates in the FlexLogic and the resulting
signals should be configured as the DUTT RX inputs.
SETTING
DUTT SCHEME
FUNCTION:
Disabled = 0
Enabled = 1
AND DUTT NO OF COMM

BITS:
SETTING AND RUN
DUTT SCHEME BLOCK:
FLEXLOGIC OPERANDS
OFF = 0 DUTT TX1
Phase DUTT TX2
FLEXLOGIC OPERANDS TRANSMIT TABLE
Selector DUTT TX3
PH DIST Z1 PKP
OR DUTT TX4
GND DIST Z1 PKP FLEXLOGIC OPERANDS
AR FORCE 3P TRIP
OPEN POLE OP
SETTINGS
DUTT NO OF COMM
BITS: SETTINGS
DUTT SEAL-IN
DUTT RX1: DELAY:
FLEXLOGIC OPERAND
Off = 0 0
AND t RST DUTT OP
5 DUTT RX2:
Off = 0
DUTT RX3: OR
DUTT NO OF COMM
BITS:
Off = 0
RUN
DUTT RX4:
RX FLEXLOGIC OPERANDS
Off = 0 DUTT TRIP A
Phase DUTT TRIP B
Selector TRIP TABLE
DUTT TRIP C
DUTT TRIP 3P
FLEXLOGIC OPERANDS
AR FORCE 3P TRIP
OPEN POLE OP
837012AD.CDR
Figure 5–164: DUTT SCHEME LOGIC

c) PERMISSIVE UNDER-REACHING TRANSFER TRIP (PUTT)

PATH: SETTINGS  CONTROL ELEMENTS  PILOT SCHEMES  PUTT SCHEME
 PUTT SCHEME PUTT SCHEME Range: Disabled, Enabled

PUTT SCHEME BLOCK: Range: FlexLogic operand
MESSAGE
Off
PUTT RX PICKUP Range: 0.000 to 65.535 s in steps of 0.001
MESSAGE
DELAY: 0.000 s
PUTT SEAL-IN Range: 0.000 to 65.535 s in steps of 0.001
MESSAGE
DELAY: 0.010 s
PUTT NO OF COMM Range: 1, 2, or 4
MESSAGE
BITS: 1
PUTT RX1: Range: FlexLogic operand
MESSAGE
Off
MESSAGE
Off
MESSAGE
Off
MESSAGE
Off
PUTT SCHEME TARGET: Range: Self-Reset, Latched, Disabled 5
MESSAGE
Self-Reset
PUTT SCHEME EVENTS: Range: Disabled, Enabled
MESSAGE
Disabled
This scheme uses an under-reaching zone 1 distance element to key a transfer trip signal(s) to the remote terminal(s)
where it is supervised by an over-reaching zone 2 distance element. For proper operation, the zone 1 and 2 phase and
ground distance elements must be enabled, configured, and set per rules of distance relaying.
In single-pole tripping applications, the scheme uses local fault type identification provided by the phase selector together
with information received from the remote terminal(s). The scheme generates output operands (PUTT TX1 through PUTT
TX4) that are used to transmit the signal to the remote end(s). Choices of communications channel include remote inputs/
outputs and telecommunications interfaces. When used with telecommunications facilities the output operands should be
assigned to operate output contacts connected to assert the individual bits at the interface.
To make the scheme a fully operational stand-alone feature, the scheme output operands must be configured to interface
with other relay functions, output contacts in particular. Typically, the output operands should be programmed to initiate a
trip, breaker fail, and autoreclose, and drive a user-programmable LED as per user application. When used in conjunction
with the Trip Output element, the scheme is pre-configured to initiate trip, breaker fail and single-pole autoreclose actions.
• PUTT SCHEME BLOCK: This setting allows the user to assign any FlexLogic operand to block the scheme. Contact
• PUTT RX PICKUP DELAY: This setting enables the relay to cope with spurious receive signals. This delay should be
set longer than the longest spurious TX signal that can be received simultaneously with the zone 1 pickup. The
selected delay will increase the response time of the scheme.
• PUTT SEAL-IN DELAY: The output FlexLogic operand (PUTT OP) is produced according to the PUTT scheme logic. A
seal-in time delay is applied to this operand for coping with noisy communication channels such as a power line carrier.
The PUTT SEAL-IN DELAY is a minimum guaranteed duration of the PUTT OP pulse. As this operand activates the trip
table of the PUTT scheme, the trip operands PUTT TRIP A, B, C and 3P are sealed-in for the same period of time.
• PUTT NO OF COMM BITS: This setting specifies the number of bits of the communications channel available for the
scheme. The transmit codes and trip table of the PUTT scheme are identical as those for the direct under-reaching
transfer trip scheme. Please refer to Chapter 8: Theory of Operation for more information.

• PUTT RX1 through PUTT RX4: These settings allow the user to select the FlexLogic operands that represent the
receive signals for the scheme. Typically input contacts interfacing with a signaling system are used. In single-bit appli-
cations, PUTT RX1 must be used. In two-bit applications, PUTT RX1 and PUTT RX2 must be used. In four-bit applica-
tions, PUTT RX1, PUTT RX2, PUTT RX3, and PUTT RX4 must be used. In multi-terminal applications, the RX signals from
two or more remote terminals should be connected through OR gates in the FlexLogic and the resulting signals should
be configured as the PUTT RX inputs.
SETTING
PUTT SCHEME
FUNCTION:
Disabled = 0
Enabled = 1
AND
SETTING
PUTT SCHEME BLOCK:
OFF = 0 SETTINGS
PUTT RX PICKUP
SETTINGS DELAY: SETTINGS
PUTT NO OF COMM tPKP
AND PUTT SEAL-IN
BITS: 0 DELAY:
0 FLEXLOGIC OPERAND
PUTT RX1:
AND t RST PUTT OP
Off = 0
PUTT RX2:
PUTT NO OF COMM
Off = 0
BITS:
PUTT RX3: OR RUN
FLEXLOGIC OPERANDS
Off = 0 RX
PUTT TRIP A
5
PUTT RX4: Phase PUTT TRIP B
Selector TRIP TABLE
PUTT TRIP C
Off = 0
PUTT TRIP 3P
FLEXLOGIC OPERANDS
FLEXLOGIC OPERANDS
AR FORCE 3P TRIP
PH DIST Z2 PKP OPEN POLE OP
OR
GND DIST Z2 PKP
PUTT NO OF COMM
FLEXLOGIC OPERANDS BITS:
PH DIST Z1 PKP AND RUN
OR
FLEXLOGIC OPERANDS
GND DIST Z1 PKP
PUTT TX1
Phase PUTT TX2
TRANSMIT TABLE
Selector PUTT TX3
FLEXLOGIC OPERANDS PUTT TX4
AR FORCE 3P TRIP
OPEN POLE OP 837013AD.CDR
Figure 5–165: PUTT SCHEME LOGIC

d) PERMISSIVE OVER-REACHING TRANSFER TRIP (POTT)

PATH: SETTINGS  CONTROL ELEMENTS  PILOT SCHEMES  POTT SCHEME
 POTT SCHEME POTT SCHEME Range: Disabled, Enabled

POTT SCHEME BLOCK: Range: FlexLogic operand
MESSAGE
Off
POTT PERMISSIVE Range: Disabled, Enabled, Custom
MESSAGE
ECHO: Disabled
POTT ECHO COND: Range: FlexLogic operand
MESSAGE
Off
POTT RX PICKUP Range: 0.000 to 65.535 s in steps of 0.001
MESSAGE
DELAY: 0.000 s
TRANS BLOCK PICKUP Range: 0.000 to 65.535 s in steps of 0.001
MESSAGE
DELAY: 0.020 s
TRANS BLOCK RESET Range: 0.000 to 65.535 s in steps of 0.001
MESSAGE
DELAY: 0.090 s
ECHO DURATION: Range: 0.000 to 65.535 s in steps of 0.001
MESSAGE
0.100 s
ECHO LOCKOUT: Range: 0.000 to 65.535 s in steps of 0.001
MESSAGE
0.250 s
LINE END OPEN PICKUP Range: 0.000 to 65.535 s in steps of 0.001 5
MESSAGE
DELAY: 0.050 s
POTT SEAL-IN Range: 0.000 to 65.535 s in steps of 0.001
MESSAGE
DELAY: 0.010 s
GND DIR O/C FWD: Range: FlexLogic operand
MESSAGE
Off
POTT NO OF COMM Range: 1, 2, or 4
MESSAGE
BITS: 1
POTT RX1: Range: FlexLogic operand
MESSAGE
Off
MESSAGE
Off
MESSAGE
Off
MESSAGE
Off
POTT SCHEME TARGET: Range: Self-Reset, Latched, Disabled
MESSAGE
Self-Reset
POTT SCHEME EVENTS: Range: Disabled, Enabled
MESSAGE
Disabled
This scheme is primarily intended for two-terminal line applications. The scheme uses an over-reaching Zone 2 distance
element to essentially compare the direction to a fault at both terminals of the line. Ground directional overcurrent functions
available in the relay can be used in conjunction with the Zone 2 distance element to key the scheme and initiate its opera-
tion. This provides increased coverage for high-resistance faults.

For proper operation, the Zone 2 phase and ground distance elements must be enabled, configured and set per rules of
distance relaying. The Line Pickup element should be enabled, configured and set properly to detect line-end-open/weak-
infeed conditions. If used by this scheme, the selected ground directional overcurrent function(s) must be enabled, config-
ured and set accordingly.
In single-pole tripping applications, the scheme uses local fault type identification provided by the Phase Selector together
with information received from the remote terminal. The scheme generates output operands (POTT TX1 through POTT TX4)
that are used to transmit the signal to the remote end. Choices of communications channel include remote inputs/outputs
and telecommunications interfaces. When used with telecommunications facilities the output operands should be assigned
to operate output contacts connected to assert the individual bits at the interface.
To make the scheme fully operational as a stand-alone feature, the scheme output operands must be configured to inter-
face with other relay functions, output contacts in particular. Typically, the output operands should be programmed to initiate
a trip, breaker fail, and autoreclose, and drive a user-programmable LED as per user application.
When used in conjunction with the Trip Output element, the scheme is pre-configured to initiate trip, breaker fail, and single-
pole autoreclose actions.
• POTT SCHEME BLOCK: This setting allows the user to assign any FlexLogic operand to block the scheme. Contact
• POTT PERMISSIVE ECHO: If this setting is set to “Enabled”, the scheme sends a permissive echo signal to the
remote end(s) using a pre-programmed logic (see the following logic diagram). If set to “Custom”, the echo signal is
sent if a condition selected via the POTT ECHO COND setting is satisfied. The echo is sent only once and then the logic
locks out for the time specified by the ECHO LOCKOUT. The duration of the echo pulse is settable as ECHO DURATION.
Operation of the overreaching protection elements (Distance Zone 2 or GND DIR O/C FWD setting) inhibits the echo.
• POTT ECHO COND: This setting specifies a user-selected echo condition and applies only if the HYB POTT PERMIS-
is set to “Custom”.
SIVE ECHO
5 • POTT RX PICKUP DELAY: This setting enables the relay to cope with spurious receive signals. The delay should be
set longer than the longest spurious TX signal that can be received simultaneously with the Zone 2 pickup. The
selected delay will increase the response time of the scheme.
• TRANS BLOCK PICKUP DELAY: This setting defines a transient blocking mechanism embedded in the POTT
scheme for coping with the exposure of a ground directional overcurrent function (if used) to current reversal condi-
tions. The transient blocking mechanism applies to the ground overcurrent path only as the reach settings for the Zone
2 distance functions is not expected to be long for two-terminal applications, and the security of the distance functions
is not endangered by the current reversal conditions.
Upon receiving the POTT RX signal, the transient blocking mechanism allows the RX signal to be passed and aligned
with the GND DIR O/C FWD indication only for a period of time set by TRANS BLOCK PICKUP DELAY. After that the ground
directional overcurrent path will be virtually disabled for a period of time specified as TRANS BLOCK RESET DELAY.
The TRANS BLOCK PICKUP DELAY should be long enough to give the selected ground directional overcurrent function
time to operate, but not longer than the fastest possible operation time of the protection system that can create current
reversal conditions within the reach of the selected ground directional overcurrent function.
This setting should take into account the POTT RX PICKUP DELAY. The POTT RX signal is shaped for aligning with the
ground directional indication as follows: the original RX signal is delayed by the POTT RX PICKUP DELAY, then terminated
at TRANS BLOCK PICKUP DELAY after the pickup of the original POTT TX signal, and eventually locked-out for TRANS
BLOCK RESET DELAY.
• TRANS BLOCK RESET DELAY: This setting defines a transient blocking mechanism embedded in the POTT scheme
for coping with the exposure of a ground directional overcurrent function (if used) to current reversal conditions (see
the TRANS BLOCK PICKUP DELAY). This delay should be selected long enough to cope with transient conditions includ-
ing not only current reversals but also spurious negative- and zero-sequence currents occurring during breaker opera-
tions. The breaker failure time of the surrounding protection systems within the reach of the ground directional function
used by the POTT scheme may be considered to make sure that the ground directional function is not jeopardized dur-
ing delayed breaker operations.
• ECHO DURATION: This setting defines the guaranteed and exact duration of the echo pulse. The duration does not
depend on the duration and shape of the received RX signal. This setting enables the relay to avoid a permanent lock-
up of the transmit/receive loop.
• ECHO LOCKOUT: This setting defines the lockout period for the echo logic after sending the echo pulse.

• LINE END OPEN PICKUP DELAY: This setting defines the pickup value for validation of the line end open conditions
as detected by the Line Pickup logic through the LINE PICKUP LEO PKP FlexLogic operand. The validated line end open
condition is a requirement for the POTT scheme to return a received echo signal (if the echo feature is enabled). This
value should take into account the principle of operation and settings of the Line Pickup element.
• POTT SEAL-IN DELAY: The output FlexLogic operand (POTT OP) is produced according to the POTT scheme logic. A
seal-in time delay is applied to this operand for coping with noisy communication channels. The POTT SEAL-IN DELAY
defines a minimum guaranteed duration of the POTT OP pulse. As this operand activates the trip table of the POTT
scheme, the trip operands POTT TRIP A, B, C and 3P are sealed-in for the same period of time.
• GND DIR O/C FWD: This setting defines the FlexLogic operand (if any) of a protection element that is used in addition
to the Zone 2 for identifying faults on the protected line, and thus, for keying the communication channel and initiating
operation of the scheme. Good directional integrity is the key requirement for an over-reaching forward-looking protec-
tion element used as GND DIR O/C FWD. Even though any FlexLogic operand could be used as GND DIR O/C FWD allow-
ing the user to combine responses of various protection elements, or to apply extra conditions through FlexLogic
equations, this extra signal is primarily meant to be the output operand from either the negative-sequence directional
overcurrent or neutral directional overcurrent. Both of these elements have separate forward (FWD) and reverse (REV)
output operands. The forward indication should be used (NEG SEQ DIR OC1 FWD or NEUTRAL DIR OC1 FWD). For greater
security and to overcome spurious directional element operation during transients, adding at least 0.5 cycles of pickup
delay to the forward directional element is recommended.
• POTT NO OF COMM BITS: This setting specifies the number of bits of the communications channel available for the
scheme. The transmit codes and trip tables of the POTT scheme are the same as those for the permissive under-
reaching transfer trip scheme. Please refer to the description of the PUTT scheme for more information.
• POTT RX1 through POTT RX4: These settings allow the user to select the FlexLogic operands that represent the
receive signals for the scheme. Typically input contacts interfacing with a signaling system are used. In single-bit appli-
cations, POTT RX1 must be used. In two-bit applications, POTT RX1 and POTT RX2 must be used. In four-bit applications,
POTT RX1, POTT RX2, POTT RX3, and POTT RX4 must be used. 5

SETTING
POTT SCHEME
FUNCTION:
Disabled = 0
Enabled = 1
AND
SETTING
POTT SCHEME BLOCK:
OFF = 0
FLEXLOGIC OPERANDS AND

AND
PH DIST Z2 PKP
OR
GND DIST Z2 PKP
SETTINGS
SETTING POTT SEAL-IN
DELAY:
GND DIR O/C FWD: FLEXLOGIC OPERAND
OR 0 POTT OP
AND t RST
Off = 0
SETTINGS POTT NO OF COMM

BITS:
POTT NO OF COMM SETTINGS
BITS: RUN
POTT RX PICKUP
DELAY: AND FLEXLOGIC OPERANDS
Phase
POTT RX1: POTT TRIP A
t PKP Selector
AND TRIP TABLE
Off = 0 0 RX POTT TRIP B
POTT TRIP C
POTT RX2: FLEXLOGIC OPERANDS
SETTINGS POTT TRIP 3P
AR FORCE 3P TRIP
Off = 0 TRANS BLOCK PICKUP AND OPEN POLE OP
DELAY:
POTT RX3: OR
TRANS BLOCK RESET
Off = 0 DELAY: POTT NO OF COMM
t PKP BITS:
POTT RX4: t RST OR RUN
Off = 0
100 msec AR FORCE 3P TRIP
OPEN POLE OP
TRANSMIT TABLE
SETTING Phase
Selector
POTT PERMISSIVE ECHO:
5
FLEXLOGIC OPERANDS
Disabled SETTINGS SETTINGS POTT TX1
Off AND RUN POTT TX2
LINE END OPEN PICKUP ECHO DURATION:
DELAY: POTT TX3
Enabled POTT TX4
LINE PICKUP LEO PKP
t PKP ECHO LOCKOUT:
0
Echo duration and lockout logic
SETTING
RX ECHO TABLE
POTT ECHO COND:
Phase
Custom Selector
Off = 0
FLEXLOGIC OPERANDS
AR FORCE 3P TRIP
OPEN POLE OP 837014AH.CDR
Figure 5–166: POTT SCHEME LOGIC

e) PERMISSIVE OVER-REACHING TRANSFER TRIP (POTT1)

PATH: SETTINGS  CONTROL ELEMENTS  PILOT SCHEMES  POTT1 SCHEME
 POTT1 SCHEME POTT1 SCHEME Range: Disabled, Enabled

POTT1 SCHEME BLOCK: Range: FlexLogic operand
MESSAGE
Off
POTT1 PERMISSIVE Range: Disabled, Enabled, Custom
MESSAGE
ECHO: Disabled
POTT1 ECHO COND: Range: FlexLogic operand
MESSAGE
Off
POTT1 RX PICKUP Range: 0.000 to 65.535 s in steps of 0.001
MESSAGE
DELAY: 0.000 s
MESSAGE
DELAY: 0.020 s
MESSAGE
DELAY: 0.090 s
ECHO DURATION: Range: 0.000 to 65.535 s in steps of 0.001
MESSAGE
0.100 s
MESSAGE
0.250 s
LINE END OPEN PICKUP Range: 0.000 to 65.535 s in steps of 0.001 5
MESSAGE
DELAY: 0.050 s
POTT1 SEAL-IN Range: 0.000 to 65.535 s in steps of 0.001
MESSAGE
DELAY: 0.010 s
DIR FWD1: Range: FlexLogic operand
MESSAGE
Off
MESSAGE
Off
MESSAGE
Off
POTT1 NO OF COMM Range: 1, 2, or 4
MESSAGE
BITS: 1
POTT1 RX1: Range: FlexLogic operand
MESSAGE
Off
MESSAGE
Off
MESSAGE
Off
MESSAGE
Off
POTT1 SCHEME TARGET: Range: Self-Reset, Latched, Disabled
MESSAGE
Self-Reset
POTT1 SCHEME EVENTS: Range: Disabled, Enabled
MESSAGE
Disabled

The POTT1 pilot scheme operates the same way as the regular POTT scheme, except hard-coded connections to phase
and ground distance elements are removed to allow the user to choose directional elements, for example ground OC direc-
tional elements. This allows a user to apply the POTT1 scheme using solely directional elements to achieve better coordi-
nation, rather than mixing up distance and ground OC directional elements together.
The settings and application guidance for the POTT scheme applies to the POTT1 scheme. See the POTT section.
• DIR FWD1..3: This setting defines the FlexLogic operand of a protection element used for keying the communication
channel and initiating operation of the scheme. Good directional integrity is the key requirement for an over-reaching
forward-looking protection element used as DIR FWD.
Even though any FlexLogic operand can be used as DIR FWD allowing the user to combine responses of various pro-
tection elements, or to apply extra security conditions through FlexLogic equations, this signal is primarily meant to be
the output operand from either the Negative-Sequence Directional IOC or Neutral Directional IOC. Both of these ele-
ments have separate forward (FWD) and reverse (REV) output operands. The forward indication is used (NEG SEQ
DIR OC1 FWD or NEUTRAL DIR OC1 FWD).
SETTING
POTT1 SCHEME
FUNCTION:
Disabled = 0
AND
SETTING
POTT1 SCHEME BLOCK:
OFF = 0
SETTING
DIR FWD1: AND
Off = 0
DIR FWD2:
SETTINGS
Off = 0 OR
POTT1 SEAL-IN
DIR FWD3: DELAY:
5
FLEXLOGIC OPERAND
Off = 0
0 POTT1 OP
t RST
SETTINGS POTT NO OF COMM

BITS:
POTT1 NO OF COMM SETTINGS
BITS: RUN
POTT1 RX PICKUP
DELAY: AND FLEXLOGIC OPERANDS
Phase
POTT1 RX1: POTT1 TRIP A
t PKP Selector
AND TRIP TABLE
Off = 0 0 RX POTT1 TRIP B
POTT1 TRIP C
POTT1 RX2: FLEXLOGIC OPERANDS
SETTINGS POTT1 TRIP 3P
AR FORCE 3P TRIP
Off = 0 TRANS BLOCK PICKUP AND OPEN POLE OP
DELAY:
POTT1 RX3: OR
TRANS BLOCK RESET
Off = 0 DELAY: POTT NO OF COMM
t PKP BITS:
POTT1 RX4: t RST RUN
Off = 0
100 msec AR FORCE 3P TRIP
OPEN POLE OP
TRANSMIT TABLE
SETTING Phase
Selector
POTT1 PERMISSIVE ECHO:
FLEXLOGIC OPERANDS
Disabled SETTINGS SETTINGS POTT1 TX1
Off AND RUN POTT1 TX2
LINE END OPEN PICKUP ECHO DURATION:
DELAY: POTT1 TX3
Enabled POTT1 TX4
LINE PICKUP LEO PKP
t PKP ECHO LOCKOUT:
0
Echo duration and lockout logic
SETTING
RX ECHO TABLE
POTT ECHO COND:
Phase
Custom Selector
Off = 0
FLEXLOGIC OPERANDS
AR FORCE 3P TRIP
OPEN POLE OP 837039A2.CDR
Figure 5–167: POTT1 (GROUND) SCHEME LOGIC

f) HYBRID PERMISSIVE OVER-REACHING TRANSFER TRIP

PATH: SETTINGS  CONTROL ELEMENTS  PILOT SCHEMES  HYBRID POTT SCHEME
 HYBRID POTT SCHEME HYB POTT SCHEME Range: Disabled, Enabled

HYB POTT BLOCK: Range: FlexLogic operand
MESSAGE
Off
HYB POTT PERMISSIVE Range: Disabled, Enabled, Custom
MESSAGE
ECHO: Disabled
HYB POTT ECHO COND: Range: FlexLogic operand
MESSAGE
Off
HYB POTT WEAK Range: Disabled, Enabled, Custom
MESSAGE
INFEED: Enabled
HYB POTT W/I COND: Range: FlexLogic operand
MESSAGE
Off
HYB POTT RX PICKUP Range: 0.000 to 65.535 s in steps of 0.001
MESSAGE
DELAY: 0.000 s
MESSAGE
DELAY: 0.020 s
MESSAGE
DELAY: 0.090 s
ECHO DURATION: Range: 0.000 to 65.535 s in steps of 0.001 5
MESSAGE
0.100 s
MESSAGE
0.250 s
HYB POTT SEAL-IN Range: 0.000 to 65.535 s in steps of 0.001
MESSAGE
DELAY: 0.010 s
MESSAGE
Off
GND DIR O/C REV: Range: FlexLogic operand
MESSAGE
Off
HYB POTT NO OF COMM Range: 1, 2, or 4
MESSAGE
BITS: 1
HYB POTT RX1: Range: FlexLogic operand
MESSAGE
Off
MESSAGE
Off
MESSAGE
Off
MESSAGE
Off
HYB POTT SCHEME Range: Self-Reset, Latched, Disabled
MESSAGE
TARGET: Self-Reset
HYB POTT EVENT: Range: Disabled, Enabled
MESSAGE
Disabled

Generally, this scheme uses an overreaching zone 2 distance element to essentially compare the direction to a fault at all
terminals of the line. Ground directional overcurrent functions available in the D60 can be used in conjunction with the zone
2 distance element to key the scheme and initiate operation. This increases the coverage for high-resistance faults.
The scheme is intended for three-terminal and two-terminal applications with weak-infeed conditions. As a long reach of the
overreaching distance element may be required for three-terminal applications, transient blocking logic is provided for both
distance and ground directional overcurrent elements. In order to cope with weak-infeed conditions an echo feature is
made available.
By default the scheme uses the reverse-looking zone 4 distance element to identify reverse faults. Additionally, reverse-
looking ground directional overcurrent functions can be used in conjunction with the zone 4.
For proper operation, the zone 2 and 4 phase and ground distance elements must be enabled, configured and set per rules
of distance relaying. The line pickup element should be enabled, configured and set properly to detect line-end-open/weak-
infeed and undervoltage conditions. If used by the scheme, the selected ground directional overcurrent function(s) must be
enabled, configured, and set accordingly.
with information received from the remote terminal. The scheme generates output operands (HYBRID POTT TX1 through
HYBRID POTT TX4) that are used to transmit the signal to the remote terminal(s). Choices of communications channel
include remote inputs/outputs and telecommunications interfaces. When used with telecommunications facilities the output
operand should be assigned to operate an output contact connected to key the transmitter at the interface. When used with
telecommunications facilities the output operands should be assigned to operate output contacts connected to assert the
individual bits at the interface.
a trip, breaker fail, and autoreclose, and drive a user-programmable LED as per user application.
5 When used in conjunction with the trip output element, the scheme is pre-configured to initiate trip, breaker fail and single-
• HYB POTT BLOCK: This setting allows the user to assign any FlexLogic operand to block the scheme. Contact inputs
from a pilot cut-out switch are typically used for this purpose.
• HYB POTT PERMISSIVE ECHO: If set to “Enabled”, the scheme sends a permissive echo signal to the remote end(s)
using a pre-programmed logic (refer to the logic diagram below). If set to “Custom”, the echo signal is sent if a condi-
tion selected via the HYB POTT ECHO COND setting is satisfied. The echo is sent only once and then the logic locks out
for the time specified by the ECHO LOCKOUT setting. The duration of the echo pulse is settable as ECHO DURATION.
Operation of the overreaching protection elements (distance zone 2 or GND DIR O/C FWD setting) inhibits the echo.
• HYB POTT ECHO COND: This setting specifies a user-selected echo condition and applies only if the HYB POTT PER-
is set to “Custom”.
MISSIVE ECHO
• HYB POTT WEAK INFEED: If this setting is set to “Enabled”, the scheme activates both the keying and operating
paths using a pre-programmed weak infeed logic (refer to the logic diagram below). If this setting is set to “Custom”,
the weak infeed condition is to be specified by the user via the HYB POTT W/I COND setting.
• HYB POTT W/I COND: This setting specifies user-selected weak infeed condition and applies only if the HYB POTT
WEAK INFEED is set to “Custom”.
• HYB POTT RX PICKUP DELAY: This setting enables the relay to cope with spurious received signals. The delay
should be set longer than the longest spurious TX signal that can be received simultaneously with the zone 2 pickup.
The selected delay will increase the response time of the scheme.
• TRANS BLOCK PICKUP DELAY: This setting defines a transient blocking mechanism embedded in the hybrid POTT
scheme for coping with the exposure of both the over-reaching zone 2 and ground directional overcurrent function to
current reversal conditions.
The transient blocking logic applies to both operate (trip) and send (transmit) paths. Identifying the fault as a reverse
fault prevents the scheme from both operating and keying the channel. If the reverse fault condition prevails for TRANS
BLOCK PICKUP DELAY, the blocking operation will be extended by the transient blocking timer for TRANS BLOCK RESET
DELAY. This allows riding through current reversal conditions.
However, if distance zone 1 picks up during the transient blocking condition, the blocking action is removed. This is to
cope with evolving faults when an external fault is followed by an internal fault. Without the zone 1 feedback, the trip
would be delayed unnecessarily.

The TRANS BLOCK PICKUP DELAY should not be longer than the fastest possible trip time for faults on an adjacent line
so that extended blocking action could be established. This should take into account the pickup time of the reverse-
looking elements of the scheme.
The delay defined by this setting should not be too short in order to avoid locking up a spurious reverse fault indication
that can occur during internal fault conditions.
• TRANS BLOCK RESET DELAY: This setting defines a transient blocking mechanism embedded in the hybrid POTT
scheme for coping with the exposure of the overreaching protection functions to current reversal conditions (see also
the TRANS BLOCK PICKUP DELAY).
This delay should be selected long enough to cope with transient conditions including not only current reversals but
also spurious negative and zero-sequence currents occurring during breaker operations (in the case when neutral
directional overcurrent or negative-sequence directional overcurrent functions are used). The breaker failure time of
the surrounding protection systems within the reach of the ground directional function used by the hybrid POTT
scheme should be considered to make sure that the ground directional function is not jeopardized during delayed
breaker operations.
• ECHO DURATION: This setting defines the guaranteed and exact duration of the echo pulse. The duration is not
dependent on the duration and shape of received RX signals. This setting enables the relay to avoid a permanent lock-
• ECHO LOCKOUT: This setting defines the lockout period for the echo logic after sending the echo pulse. This enables
the relay to avoid oscillations of the echo pulses during an autoreclosure dead-time after clearing an internal fault.
• HYB POTT SEAL-IN DELAY: The output FlexLogic operand (HYB POTT OP) is produced according to the hybrid POTT
scheme logic. The HYB POTT SEAL-IN DELAY defines a minimum guaranteed duration of the HYB POTT OP pulse. As this
operand runs the trip table of the hybrid POTT scheme, the trip operands HYB POTT TRIP A, B, C and 3P are sealed-in
for the same period of time.
• GND DIR O/C FWD: This setting defines the FlexLogic operand (if any) of a protection element that is used in addition 5
to zone 2 for identifying faults on the protected line, and thus, for keying the communication channel and initiating oper-
ation of the scheme (both through the transient blocking logic). Good directional integrity is the key requirement for an
over-reaching forward-looking protection element used as GND DIR O/C FWD.
Even though any FlexLogic operand could be used as GND DIR O/C FWD enabling the user to combine responses of var-
ious protection elements or to apply extra conditions through FlexLogic equations, this extra signal is primarily meant
to be the output operand from either the negative-sequence directional or neutral directional overcurrent elements.
Both these elements have separate forward (FWD) and reverse (REV) output operands. The forward indication should
be used (NEG SEQ DIR OC1 FWD or NEUTRAL DIR OC1 FWD).
The selected protection element (or elements in combination) should be coordinated with the selection of GND DIR O/C
REV. For all the forward external faults seen by an element used as GND DIR O/C FWD at one end of the line, the reverse-
looking element used as GND DIR O/C REV at the other end should pickup and provide a blocking signal. For greater
security and to overcome spurious directional element operation during transients, adding at least 0.5 cycles of pickup
delay to the forward directional element is recommended.
• GND DIR O/C REV: This setting defines the FlexLogic operand (if any) of a protection element used in addition to zone
4 for identifying reverse faults, and thus, for stopping the transmit signal and initiating the transient blocking timer.
Good directional integrity is the key requirement for a reverse-looking protection element used as GND DIR O/C REV.
Even though any FlexLogic operand could be used as GND DIR O/C REV enabling the user to combine responses of var-
to be the output operand from either the negative sequence directional or neutral directional overcurrent element. Both
these elements have separate forward (FWD) and reverse (REV) output operands. The reverse indication should be
used (NEG SEQ DIR OC1 REV or NEUTRAL DIR OC1 REV).
FWD. For all the forward external faults seen by an element used as GND DIR O/C FWD at one end of the line, the
reverse-looking element used as GND DIR O/C REV at the other end should pickup and provide a blocking signal. For
greater security and to overcome spurious directional element operation during transients, adding a pickup delay
greater than the pilot channel delay to the reverse directional element is recommended.
• HYB POTT NO OF COMM BITS: This setting specifies the number of bits of the communications channel available for
the scheme. The transmit codes and trip table of the hybrid POTT scheme are the same as those for the permissive
under-reaching transfer trip scheme. Please refer to the description of the PUTT scheme for more information.

• HYB POTT RX1 through HYB POTT RX4: These settings allow the user to select the FlexLogic operands that repre-
sent the receive signals for the scheme. Typically input contacts interfacing with a signaling system are used. In single-
bit applications, HYB POTT RX1 must be used. In two-bit applications, HYB POTT RX1 and HYB POTT RX2 must be used. In
four-bit applications, HYB POTT RX1, HYB POTT RX2, HYB POTT RX3, and HYB POTT RX4 must be used.
SETTING SETTING
HYB POTT WEAK
GND DIR O/C FWD:
INFEED:
Off = 0
FLEXLOGIC OPERANDS OR
PH DIST Z2 PKP
GND DIST Z2 PKP
Disabled
Off OR
FLEXLOGIC OPERAND
LINE PICKUP LEO PKP
OPEN POLE OP Enabled
AND
LINE PICKUP UV PKP
SETTING
HYB POTT W/I COND:

Custom
Off = 0
SETTING
HYB POTT SCHEME
FUNCTION: SETTING
Disabled=0 HYB POTT SEAL-IN
Enabled=1 DELAY:
FLEXLOGIC OPERAND
AND 0
AND HYB POTT OP
t RST
SETTING
HYB POTT BLOCK:

SETTING
5
Off = 0
HYB POTT NO OF
COMM BITS:
RUN
SETTINGS SETTING FLEXLOGIC OPERANDS
AND Phase
HYB POTT NO OF HYB POTT RX PICKUP Selector HYB POTT TRIP A
COMM BITS: DELAY:
RX HYB POTT TRIP B
TRIP TABLE
HYB POTT RX1: t PKP HYB POTT TRIP C
0 FLEXLOGIC OPERANDS HYB POTT TRIP 3P
Off = 0 AR FORCE 3P TRIP
HYB POTT RX2: OPEN POLE OP
Off = 0 0
100 msec
HYB POTT RX3: OR
Off = 0
SETTING
HYB POTT RX4:
HYB POTT SETTINGS
Off = 0 PERMISSIVE ECHO:
ECHO DURATION: SETTING
Disabled HYB POTT NO OF
Off
ECHO LOCKOUT: COMM BITS:
AND RUN
Echo duration and
Enabled AND lockout logic RX
SETTING AND
Phase
HYB POTT ECHO COND: Selector ECHO TABLE
Custom FLEXLOGIC OPERANDS
Off=0 FLEXLOGIC OPERANDS
AR FORCE 3P TRIP
HYB POTT TX1
OPEN POLE OP
HYB POTT TX2
SETTINGS
SETTING RUN HYB POTT TX3
TRANS BLOCK PICKUP AND
HYB POTT TX4
GND DIR O/C REV: DELAY: OR
TRANS BLOCK RESET Phase
Off = 0
DELAY: Selector
t PKP TRANSMIT TABLE
FLEXLOGIC OPERANDS OR OR FLEXLOGIC OPERANDS
t RST
PH DIST Z4 PKP AR FORCE 3P TRIP
GND DIST Z4 PKP OPEN POLE OP 837015AL.CDR
PH DIST Z1 PKP
GND DIST Z1 PKP
Figure 5–168: HYBRID POTT SCHEME LOGIC

g) DIRECTIONAL COMPARISON BLOCKING

PATH: SETTINGS  CONTROL ELEMENTS  PILOT SCHEMES  BLOCKING SCHEME
 BLOCKING SCHEME BLOCKING SCHEME Range: Disabled, Enabled

BLOCK SCHEME BLOCK: Range: FlexLogic operand
MESSAGE
Off
BLOCK RX CO-ORD PKP Range: 0.000 to 65.535 s in steps of 0.001
MESSAGE
DELAY: 0.010 s
MESSAGE
DELAY: 0.030 s
MESSAGE
DELAY: 0.090 s
BLOCK SCHEME SEAL-IN Range: 0.000 to 65.535 s in steps of 0.001
MESSAGE
DELAY: 0.010 s
MESSAGE
Off
MESSAGE
Off
BLOCK SCHEME NO OF Range: 1, 2, or 4
MESSAGE
COMM BITS: 1
BLOCK SCHEME RX1: Range: FlexLogic operand 5
MESSAGE
Off
BLOCK SCHEME RX2: Range: FlexLogic operand
MESSAGE
Off
MESSAGE
Off
MESSAGE
Off
BLOCK SCHEME TARGET: Range: Self-Reset, Latched, Disabled
MESSAGE
Self-Reset
BLOCK SCHEME EVENT: Range: Disabled, Enabled
MESSAGE
Disabled
Generally, the scheme compares the direction to a fault at all terminals of the line. Unlike the permissive schemes, the
absence of a blocking signal permits operation of the scheme. Consequently, the scheme is biased toward dependability
and requires an "on/off" type of signaling.
By default this scheme uses only a forward-looking over-reaching zone 2 distance element to identify forward faults.
Ground directional overcurrent functions available in the relay can be used in conjunction with the zone 2 distance element
to increase the coverage for high-resistance faults. Also by default, only a reverse-looking zone 4 distance element to iden-
tify reverse faults. Ground directional overcurrent functions available in the relay can be used in conjunction with the zone 4
distance element for better time and sensitivity coordination.
For proper operation, the zone 2 and 4 phase and ground distance elements must be enabled, configured and set per rules
of distance relaying. If used by this scheme, the selected ground directional overcurrent functions must be enabled, config-
ured, and programmed accordingly.
with information received from the remote terminal.

The scheme generates output operands (DIR BLOCK TX INIT and DIR BLOCK TX1 STOP through DIR BLOCK TX4 STOP) that
control the transmission of signals to the remote end(s). When used with telecommunications facilities the output operands
should be assigned to operate output contacts connected to key the transmitter at the interface.
The output operands from the scheme (DIR BLOCK A, B, C and 3P) must be configured to interface with other relay func-
tions, output contacts in particular, in order to make the scheme fully operational. Typically, the output operand should be
programmed to initiate a trip, breaker fail, and autoreclose, and drive a user-programmable LED as per user application.
When used in conjunction with the trip output element, the scheme is pre-configured to initiate trip, breaker fail, and single-
• BLOCK SCHEME BLOCK: This setting allows the user to assign any FlexLogic operand to block the scheme. Contact
• BLOCK RX CO-ORD PKP DELAY: This setting defines a delay for the forward-looking protection elements used by
the scheme for coordination with the blocking response from the remote end(s). This setting should include both the
response time of the protection elements used to establish a blocking signal and the total transmission time of that sig-
nal including the relay communications equipment interfacing and the communications channel itself.
• TRANS BLOCK PICKUP DELAY: This setting defines a transient blocking mechanism embedded in the blocking
scheme for coping with the exposure of both the over-reaching zone 2 and ground directional overcurrent function to
current reversal conditions.
The transient blocking logic applies to the send path only. Identifying the fault as a reverse fault establishes the block-
ing signal. If the reverse fault condition prevails for TRANS BLOCK PICKUP DELAY, the blocking operation will be
extended by the transient blocking timer for TRANS BLOCK RESET DELAY. This allows riding through current reversal
conditions. However, if zone 1 picks up during the transient blocking condition, the blocking action is removed. This is
done to cope with evolving faults when an external fault is followed by an internal fault. Without the zone 1 feedback,
the trip would be unnecessarily delayed.
5 The TRANS BLOCK PICKUP DELAY should not be longer than the fastest possible trip time for faults on an adjacent line
so that the extended blocking action could be established. This should take into account the pickup time of the reverse-
looking elements of the scheme. The delay defined by this setting should not be too short in order to avoid locking up a
spurious reverse fault indication that can occur during internal fault conditions.
• TRANS BLOCK RESET DELAY: This setting defines a transient blocking mechanism embedded in the blocking
scheme for coping with the exposure of the overreaching protection functions to current reversal conditions (see also
the TRANS BLOCK PICKUP DELAY).
directional or negative-sequence directional overcurrent functions are used). Breaker failure time of the surrounding
protection systems within the reach of the ground directional function used by the blocking scheme should be consid-
ered to make sure that the ground directional function is not jeopardized during delayed breaker operations.
• BLOCK SCHEME SEAL-IN DELAY: The output FlexLogic operand (DIR BLOCK OP) is produced according to the
Blocking scheme logic. The BLOCK SCHEME SEAL-IN DELAY defines a minimum guaranteed duration of the DIR BLOCK
OP pulse. As this operand runs the Trip Table of the Blocking scheme, the trip operands DIR BLOCK TRIP A, B, C and 3P
are sealed-in for the same period of time.
• GND DIR O/C FWD: This setting defines the FlexLogic operand (if any) of a protection element used in addition to
zone 2 for identifying faults on the protected line, and thus, for initiating operation of the scheme. Good directional
integrity is the key requirement for an over-reaching forward-looking protection element used as GND DIR O/C FWD.
Even though any FlexLogic operand could be used as GND DIR O/C FWD enabling the user to combine responses of var-
to be the output operand from either the negative-sequence directional or neutral directional overcurrent elements.
Both these elements have separate forward (FWD) and reverse (REV) output operands.
The forward indication should be used (NEG SEQ DIR OC1 FWD or NEUTRAL DIR OC1 FWD). The selected protection ele-
ment (or elements in combination) should be coordinated with the selection of GND DIR O/C REV. For all the forward
external faults seen by an element used as GND DIR O/C FWD at one end of the line, the reverse-looking element used
as GND DIR O/C REV at the other end should pickup and provide a blocking signal. For greater security and to overcome
spurious directional element operation during transients, adding at least 0.5 cycles of pickup delay to the forward direc-
tional element is recommended.

• GND DIR O/C REV: This setting defines the FlexLogic operand (if any) of a protection element that is used in addition
to zone 4 for identifying reverse faults, and thus, for initiating the blocking signal. Either reverse-looking directional or
non-directional overcurrent protection element may be used as GND DIR O/C REV.
Even though any FlexLogic operand could be used as GND DIR O/C REV, enabling the user to combine responses of var-
to be the output operand from either the negative-sequence directional, neutral directional, or a non-directional instan-
taneous overcurrent element.
FWD. For all the forward external faults seen by an element used as GND DIR O/C FWD at one end of the line, the
reverse-looking element used as GND DIR O/C REV at the other end should pickup and provide a blocking signal. For
greater security and to overcome spurious directional element operation during transients, adding a pickup delay
greater than the pilot channel delay to the reverse directional element is recommended.
• BLOCK SCHEME NO OF COMM BITS: This setting specifies the number of bits of the communications channel avail-
able for the scheme. With only one bit available, the scheme sends the blocking signal by asserting the DIR BLOCK TX
INIT FlexLogic operand. This operand should be used to start the channel (set the blocking signal). On internal faults,
the scheme removes the blocking signal by asserting the DIR BLOCK TX1 FlexLogic operand.
For tripping the scheme responds to lack of the blocking signal on bit 1 (BLOCK SCHEME RX1 setting). The scheme uses
only local fault type identification provided by the phase selector to assert the output operands DIR BLOCK TRIP A, B, C
and 3P. Please refer to the Theory of operation chapter for more information on communications.
To take advantage of the four-bit blocking scheme, the blocking signals should be initiated from a disturbance detector.
This can be accomplished by using both 50DD and DIR BLOCK TX INIT to assert the blocking signal. Subsequently, spe-
cific bits will be de-asserted by the scheme based on the phase selection providing the peer relay with more informa-
tion on the fault type. Otherwise, the peer relay issues a three-pole trip upon receiving the bit pattern (0, 0, 0, 0).
• BLOCK SCHEME RX1 through BLOCK SCHEME RX4: These settings allow the user to select the FlexLogic oper- 5
ands that represent the receive signals for the scheme. Typically input contacts interfacing with a signaling system are
used. In single-bit applications, BLOCK SCHEME RX1 must be used. In two-bit applications, BLOCK SCHEME RX1 and
BLOCK SCHEME RX2 must be used. In four-bit applications, BLOCK SCHEME RX1, BLOCK SCHEME RX2, BLOCK SCHEME
RX3, and BLOCK SCHEME RX4 must be used.

SETTING
BLOCKING SCHEME
FUNCTION:
Disabled=0
AND
SETTING
BLOCK SCHEME BLOCK:
OFF = 0
SETTING
BLOCKING RX CO-ORD PKP
DELAY:
FLEXLOGIC OPERANDS
PH DIST Z2 PKP AND t PKP
0
GND DIST Z2 PKP
SETTING OR
GND DIR O/C FWD:

SETTING
Off = 0
BLOCK SCHEME
SEAL-IN DELAY:
SETTING FLEXLOGIC OPERAND
0
SETTING AND t RST DIR BLOCK OP
BLOCK SCHEME NO OF
COMM BITS: BLOCK SCHEME NO OF BLOCK SCHEME NO OF
COMM BITS: COMM BITS:
BLOCKING SCHEME RX1:
RUN RUN
Off = 0 FLEXLOGIC OPERANDS
Phase
Selector DIR BLOCK TRIP A
RX TRIP TABLE DIR BLOCK TRIP B
Off = 0 TRIP TABLE DIR BLOCK TRIP C
FLEXLOGIC OPERANDS
PATTERN RECEIVED DIR BLOCK TRIP 3P
BLOCKING SCHEME RX3: (see Chapter 8 of the AR FORCE 3P TRIP
instruction manual) OPEN POLE OP
Off = 0
Off = 0 BLOCK SCHEME NO OF

COMM BITS:
AND RUN
FLEXLOGIC OPERANDS
Phase
Selector DIR BLOCK TX1 STOP
SETTING TRANSMIT TABLE DIR BLOCK TX2 STOP
DIR BLOCK TX3 STOP
GND DIR O/C REV. FLEXLOGIC OPERANDS
DIR BLOCK TX4 STOP
AR FORCE 3P TRIP
Off = 0
5
AND OPEN POLE OP
OR
FLEXLOGIC OPERANDS SETTINGS
PH DIST Z4 PKP
TRANS BLOCK PICKUP FLEXLOGIC OPERAND
GND DIST Z4 PKP DELAY:
OR DIR BLOCK TX INIT
TRANS BLOCK RESET
DELAY:
t PKP
FLEXLOGIC OPERANDS t RST
OR
PH DIST Z1 PKP
OR
GND DIST Z1 PKP 837016AG.CDR
Figure 5–169: DIRECTIONAL COMPARISON BLOCKING SCHEME LOGIC

h) DIRECTIONAL COMPARISON UNBLOCKING

PATH: SETTINGS  CONTROL ELEMENTS  PILOT SCHEMES  DCUB SCHEME
 DCUB SCHEME DCUB SCHEME Range: Disabled, Enabled

DCUB BLOCK: Range: FlexLogic operand
MESSAGE
Off
DCUB PERMISSIVE Range: Disabled, Enabled, Custom
MESSAGE
ECHO: Disabled
DCUB ECHO COND: Range: FlexLogic operand
MESSAGE
Off
MESSAGE
Off
MESSAGE
Off
TRANS BLOCK PICKUP Range: 0 to 65.535 s in steps of 0.001
MESSAGE
DELAY: 0.020 s
TRANS BLOCK RESET Range: 0 to 65.535 s in steps of 0.001
MESSAGE
DELAY: 0.090 s
ECHO DURATION: Range: 0 to 65.535 s in steps of 0.001
MESSAGE
0.100 s
ECHO LOCKOUT: Range: 0 to 65.535 s in steps of 0.001 5
MESSAGE
0.250 s
LINE END OPEN PICKUP Range: 0 to 65.535 s in steps of 0.001
MESSAGE
DELAY: 0.050 s
DCUB LOG PICKUP Range: 0 to 65.535 s in steps of 0.001
MESSAGE
DELAY: 0.008 s
GUARD HEALTHY RESET Range: 0 to 65.535 s in steps of 0.001
MESSAGE
DELAY: 0.015 s
DCUB LOG TRIP Range: 0 to 65.535 s in steps of 0.001
MESSAGE
WINDOW: 0.150 s
DCUB SEAL-IN Range: 0 to 65.535 s in steps of 0.001
MESSAGE
DELAY: 0.010 s
DCUB NO OF COMM Range: 1, 2, or 4
MESSAGE
BITS: 1
DCUB RX1: Range: FlexLogic operand
MESSAGE
Off
DCUB LOG1: Range: FlexLogic operand
MESSAGE
Off
MESSAGE
Off
MESSAGE
Off
MESSAGE
Off


MESSAGE
Off
MESSAGE
Off
MESSAGE
Off
DCUB SCHEME TARGET: Range: Self-Reset, Latched, Disabled
MESSAGE
Self-Reset
DCUB SCHEME EVENTS: Range: Disabled, Enabled
MESSAGE
Disabled
This menu allows selecting and setting up protection signaling of the directional comparison unblocking scheme. This
scheme is available for single-pole tripping applications and can be used with one, two, or four bit communications chan-
nels. Choices of communications channel include remote inputs/outputs and telecommunications interfaces.
Generally, this scheme uses an over-reaching zone 2 distance element to compare the direction to a fault at all terminals of
the line. Ground directional overcurrent functions available in the relay can be used in conjunction with the zone 2 distance
element to key the scheme and initiate its operation. This increases the coverage for high-resistance faults.
The scheme is intended for two or three-terminal applications. As a long reach of the overreaching distance element may
be required for three-terminal applications, transient blocking logic is provided for both distance and ground directional
overcurrent elements. An echo feature is made available to cope with line open conditions.
By default the scheme uses the reverse-looking zone 4 distance element to identify reverse faults. Additionally, reverse-
looking ground directional overcurrent functions can be used in conjunction with the zone 4.
5 For proper operation of the scheme the zone 2 and 4 phase and ground distance elements must be enabled, configured
and set per rules of distance relaying. The line pickup element should be enabled, configured and set properly to detect
line-end-open conditions. If used by this scheme, the selected ground directional overcurrent function(s) must be enabled,
configured and set accordingly.
with information received from the remote terminal. The scheme generates output operands ( DCUB TX1 through DCUB TX4)
that are used to transmit the signal to the remote terminal(s). The directional comparison unblocking scheme was devel-
oped for use with frequency shift keying communications channels, though different telecommunications interfaces can be
used (for example, digital communication channels utilizing the D60 teleprotection input/outputs).
a trip, breaker fail, and autoreclose, and drive a user-programmable LED as per the intended application.
When used in conjunction with the trip output element, the scheme is pre-configured to initiate trip, breaker fail and autore-
close actions.
• DCUB BLOCK: This setting allows the user to assign any FlexLogic operand to block the scheme. Contact inputs from
a pilot cut-out switch are typically used for this purpose.
• DCUB PERMISSIVE ECHO: Enabling this setting will send a permissive echo signal to the remote end(s) under cer-
tain conditions (see the logic diagram for details). If set to “Custom”, the echo signal is sent if a condition selected with
the DCUB ECHO COND setting is satisfied. The echo is sent only once and then the echo logic locks out for the time
specified by the ECHO LOCKOUT setting. The duration of the echo pulse is programmable by the ECHO DURATION set-
ting. The echo is returned only if no overreaching and reverse protection elements operate.
• DCUB ECHO COND: This setting specifies a user-selected echo condition and applies only if the DCUB PERMISSIVE
ECHO setting is “Custom”.
• GND DIR O/C FWD: This setting defines the FlexLogic operand (if any) of a protection element used in addition to
zone 2 for identifying faults on the protected line, and thus, for keying the communication channel(s) and initiating
operation of the scheme (both through the transient blocking logic).
Good directional integrity is the key requirement for an over-reaching forward-looking protection element set as GND
DIR O/C FWD. Even though any FlexLogic operand could be set as GND DIR O/C FWD, thereby enabling the user to com-
bine responses of various protection elements or to apply extra conditions through FlexLogic equations, this extra sig-

nal is primarily meant to be the output operand from either the negative-sequence directional or neutral directional
overcurrent elements. As both these elements have separate forward and reverse output operands, the forward indica-
tion should be used (that is, NEG SEQ DIR OC1 FWD or NEUTRAL DIR OC1 FWD).
REV. For all forward external faults seen by an element set as GND DIR O/C FWD at one end of the line, the reverse-look-
ing element set as GND DIR O/C REV at the other end should pickup and provide a blocking signal. For greater security
and to overcome spurious directional element operation during transients, adding at least 0.5 cycles of pickup delay to
the forward directional element is recommended.
• GND DIR O/C REV: This setting defines the FlexLogic operand (if any) of a protection element used in addition to zone
4 for identifying reverse faults, and thus, for stopping the transmit signal and initiating the transient blocking timer.
Good directional integrity is the key requirement for a reverse-looking protection element set as GND DIR O/C REV. Even
though any FlexLogic operand could be set as GND DIR O/C REV, thereby enabling the user to combine responses of
various protection elements or to apply extra conditions through FlexLogic equations, this extra signal is primarily
meant to be the output operand from either the negative-sequence directional or neutral directional overcurrent ele-
ment. As both these elements have separate forward and reverse output operands, the reverse indication should be
used (that is, NEG SEQ DIR OC1 REV or NEUTRAL DIR OC1 REV).
FWD. For all the forward external faults seen by an element set as GND DIR O/C FWD at one end of the line, the reverse-
looking element set as GND DIR O/C REV at the other end should pickup and provide a blocking signal. For greater secu-
rity and to overcome spurious directional element operation during transients, adding a pickup delay greater than the
pilot channel delay to the reverse directional element is recommended.
• TRANS BLOCK PICKUP DELAY: This setting defines a transient blocking mechanism embedded in the directional
comparison unblocking scheme for coping with the exposure of both the over-reaching zone 2 and ground directional
overcurrent function to current reversal conditions.
5
The transient blocking logic applies to both operate (trip) and send (transmit) paths. Identifying the fault as a reverse
fault prevents the scheme from both operating and keying the channel. If the reverse fault condition prevails for TRANS
BLOCK PICKUP DELAY value, the blocking operation will be extended by the transient blocking timer for the TRANS
BLOCK RESET DELAY value. This allows riding through current reversal conditions.
However, if distance zone 1 picks up during the transient blocking condition, the blocking action is removed. This is to
cope with evolving faults when an external fault is followed by an internal fault. Without the zone 1 feedback, the trip
would be delayed unnecessarily.
The TRANS BLOCK PICKUP DELAY should not be longer than the fastest possible trip time for faults on an adjacent line
so that extended blocking action could be established. This should take into account the pickup time of the reverse-
looking elements of the scheme. To avoid locking up a spurious reverse fault indication that can occur during internal
fault conditions, the delay defined by this setting should not be too short.
• TRANS BLOCK RESET DELAY: This setting defines a transient blocking mechanism embedded in the directional
comparison unblocking scheme for coping with the exposure of the overreaching protection functions to current rever-
sal conditions (see also the TRANS BLOCK PICKUP DELAY setting above).
directional or negative-sequence directional overcurrent functions are used). The breaker failure time of the surround-
ing protection systems within the reach of the ground directional function used by the directional comparison unblock-
ing scheme should be considered to make sure that the ground directional function is not jeopardized during delayed
breaker operations.
• ECHO DURATION: This setting defines the guaranteed and exact duration of the echo pulse. The duration does not
depend on the duration and shape of the received RX signals. This setting enables the relay to avoid a permanent lock-
• ECHO LOCKOUT: This setting defines the lockout period for the echo logic after sending the echo pulse. This setting
enables the relay to avoid oscillations of the echo pulses during an autoreclosure dead-time after clearing an internal
fault.
• LINE END OPEN PICKUP DELAY: This setting defines the pickup value for validation of the line end open conditions
as detected by the line pickup logic via the LINE PICKUP LEO PKP FlexLogic operand. The validated line end open con-

dition is a requirement for the directional comparison unblocking scheme to return a received echo signal (if the echo
feature is enabled).
The value of this setting should take into account the principle of operation and settings of the line pickup element,
which should thus be enabled.
• DCUB LOG PICKUP DELAY: This setting represents the directional comparison unblocking duration time delay, and is
the amount of time that the loss-of-guard without receipt of permissive trip must be present before the logic provides
permission to operate if a forward fault is detected. It is set relatively short, but long enough to ride through the transi-
tion period of loss-of-guard with the receipt of a permissive signal that occurs with a normal trip. Typical setting values
are from 4 to 32 ms. For most cases, a value of 8 ms may be used.
The tripping or unblocking window for loss-of-guard without permission is the difference between the DCUB LOG TRIP
WINDOW and DCUB LOG PICKUP DELAY timers. For the default settings, this difference is 150 – 8 = 142 ms and occurs
8 ms after loss-of-guard was received, when the DCUB LOG PICKUP DELAY timer has timed out. During this interval, the
scheme has permission to operate if a forward fault is sensed, and no reverse faults or transient blocking.
• GUARD HEALTHY RESET DELAY: This setting represents the guard healthy security time delay, and is the time after
the channel is restored that the guard signal must be present before the directional comparison unblocking scheme is
put back in service. This reset timer allows the scheme to ride through any chattering in the channel. Typical values are
from 100 to 500 ms, with a value of 150 ms commonly used.
• DCUB LOG TRIP WINDOW: This setting represents the directional comparison unblocking lockout time delay, and is
the amount of time from when any loss-of-guard signal is received until the directional comparison unblocking scheme
is locked out without the presence of any RX1 to RX4 receive signal or any forward element. This timer seals-in when it
expires, creating a blocking signal for all scheme functions and disabling the scheme until the guard signal is restored
and the GUARD HEALTHY RESET DELAY timer expires. Typical values for this setting are from 160 to 180 ms; for most
cases, a setting of about 150 ms may be used.
5 • DCUB SEAL-IN DELAY: The output FlexLogic operand (DCUB OP) is produced according to the directional compari-
son unblocking scheme logic. The DCUB SEAL-IN DELAY defines a minimum guaranteed duration of the DCUB OP pulse.
As this operand runs the trip table of the directional comparison unblocking scheme, the DCUB TRIP A, DCUB TRIP B,
DCUB TRIP C, and DCUB TRIP 3P trip operands are sealed-in for the same period of time.
• DCUB NO OF COMM BITS: This setting specifies the number of bits available on the communications channel for the
scheme. With only one bit available, the scheme sends the direct under-reaching transfer trip command on bit 1 (DCUB
TX1 operand) and responds to the direct trip command received on bit 1 (DCUB RX1 setting). The scheme uses only
local fault type identification provided by the phase selector to assert the DCUB TRIP A, DCUB TRIP B, DCUB TRIP C and
DCUB TRIP 3P output operands (see Chapter 8: Theory of Operation for details on the use of communication channels).
• DCUB RX1 through DCUB RX4: These settings allow the user to select the FlexLogic operands to represent the per-
mission receive signals for the scheme. Contact inputs interfacing with a signaling system(s) are typically used. These
settings must be used in conjunction with the loss-of-guard signals, otherwise the scheme will not unblock and thus fail
to operate.
In single-bit applications, DCUB RX1 must be used. In two-bit applications, DCUB RX1 and DCUB RX2 must be used. In
four-bit applications, DCUB RX1, DCUB RX2, DCUB RX3, and DCUB RX4 must be used.
• DCUB LOG1 through DCUB LOG4: These settings allow the user to select the FlexLogic operands to represent the
loss-of-guard receive signals for the scheme. Contact inputs interfacing with a signaling system(s) are typically used.
Each loss-of-guard signal must correspond to the same receive signal from the same communications channel (that is,
RX1 and LOG1 must be from the same communications channel, and the same for channels 2, 3 and 4, if used).
In single-bit applications, DCUB RX1 and DCUB LOG1 must be used. In two-bit applications, DCUB RX1 with DCUB LOG1
and DCUB RX2 with DCUB LOG2 must be used. In four-bit applications, all receive and loss-of-guard signals must be
used.

SETTING
DCUB SCHEME LOG = LOSS OF GUARD
FUNCTION:
Disabled = 0 AND
AND
SETTING
AND SETTINGS
DCUB BLOCKED:
DCUB SEAL-IN
Off = 0 DELAY:
FLEXLOGIC OPERANDS
SETTINGS 0
FLEXLOGIC OPERANDS OR DCUB OP
AND tRST
DCUB LOG PICKUP
GND DIST Z2 PKP DELAY:
PHS DIST Z2 PKP
tPKP DCUB NO OF COMM
SETTING OR AND BITS:
0
GND DIR O/C FWD: RUN
Phase
AND FLEXLOGIC OPERANDS
Selector
Off = 0 OR DCUB TRIP A
RX
AND DCUB TRIP B
SETTING LOG
AND TRIP TABLE DCUB TRIP C
DCUB NO OF COMM AND
DCUB TRIP 3P
BITS: FLEXLOGIC OPERANDS
AR FORCE 3P TRIP
DCUB RX1:
OPEN POLE OP
Off = 0 SETTINGS
OR AND
DCUB LOG TRIP
DCUB LOG1:
WINDOW:
Off = 0 tPKP
OR
DCUB RX2: 0
DCUB NO OF COMM
Off = 0 SETTINGS BITS:
RUN
DCUB LOG2: OR GUARD HEALTHY Phase
RESET DELAY: Selector
Off = 0
0
AND
DCUB RX3: tRST TRANSMIT TABLE
FLEXLOGIC OPERANDS
Off = 0
AR FORCE 3P TRIP FLEXLOGIC OPERANDS
0 DCUB TX1
DCUB LOG3: OPEN POLE OP
100ms SETTING DCUB TX2
Off = 0 RUN DCUB TX3
DCUB PERMISSIVE
Phase
SETTINGS ECHO: DCUB TX4
DCUB RX4: Selector
RX
TRANS BLOCK ECHO TABLE
Off = 0 SETTINGS
PICKUP DELAY: LOG
DCUB LOG4: Disabled LINE END OPEN
TRANS BLOCK Off = 0
PICKUP DELAY:
RESET DELAY: 837032A2.CDR
Off = 0 FLEXLOGIC OPERANDS
Enabled tPKP
tPKP LINE PICKUP LEO PKP
AND 0
5
SETTING tRST SETTING
OR SETTING
GND DIR O/C REV: Custom ECHO DURATION:
DCUB ECHO COND:
Off = 0 ECHO LOCKOUT:
Off = 0
AND
OR Echo duration/lockout logic
FLEXLOGIC OPERANDS OR AND
GND DIST Z4 PKP
PHS DIST Z4 PKP
GND DIST Z1 PKP
PHS DIST Z1 PKP
Figure 5–170: DIRECTIONAL COMPARISON UNBLOCKING SCHEME LOGIC

5.8 INPUTS AND OUTPUTS 5 SETTINGS
5.8INPUTS AND OUTPUTS 5.8.1 CONTACT INPUTS
PATH: SETTINGS  INPUTS/OUTPUTS  CONTACT INPUTS
 CONTACT INPUTS

 CONTACT INPUT H5a


CONTACT INPUT H5a ID: Range: up to 12 alphanumeric characters

MESSAGE
Cont Ip 1
CONTACT INPUT H5a Range: 0.0 to 16.0 ms in steps of 0.5

MESSAGE
DEBNCE TIME: 2.0 ms
CONTACT INPUT H5a Range: Disabled, Enabled

MESSAGE
EVENTS: Disabled

 CONTACT INPUT xxx


 CONTACT INPUT
 THRESHOLDS
Ips H5a,H5c,H6a,H6c Range: 17, 33, 84, 166 Vdc

MESSAGE
5 THRESHOLD: 33 Vdc
Ips H7a,H7c,H8a,H8c Range: 17, 33, 84, 166 Vdc

MESSAGE
THRESHOLD: 33 Vdc

Ips xxx,xxx,xxx,xxx Range: 17, 33, 84, 166 Vdc

MESSAGE
THRESHOLD: 33 Vdc
The contact inputs menu contains configuration settings for each contact input as well as voltage thresholds for each group
of four contact inputs. Upon startup, the relay processor determines (from an assessment of the installed modules) which
contact inputs are available and then display settings for only those inputs.
An alphanumeric ID may be assigned to a contact input for diagnostic, setting, and event recording purposes. The CON-
TACT IP X On” (Logic 1) FlexLogic operand corresponds to contact input “X” being closed, while CONTACT IP X Off corre-
sponds to contact input “X” being open. The CONTACT INPUT DEBNCE TIME defines the time required for the contact to
overcome ‘contact bouncing’ conditions. As this time differs for different contact types and manufacturers, set it as a maxi-
mum contact debounce time (per manufacturer specifications) plus some margin to ensure proper operation. If CONTACT
INPUT EVENTS is set to “Enabled”, every change in the contact input state will trigger an event.
A raw status is scanned for all Contact Inputs synchronously at the constant rate of 0.5 ms as shown in the figure below.
The DC input voltage is compared to a user-settable threshold. A new contact input state must be maintained for a user-
settable debounce time in order for the D60 to validate the new contact state. In the figure below, the debounce time is set
at 2.5 ms; thus the 6th sample in a row validates the change of state (mark no. 1 in the diagram). Once validated (de-
bounced), the contact input asserts a corresponding FlexLogic operand and logs an event as per user setting.
A time stamp of the first sample in the sequence that validates the new state is used when logging the change of the con-
tact input into the Event Recorder (mark no. 2 in the diagram).
Protection and control elements, as well as FlexLogic equations and timers, are executed eight times in a power system
cycle. The protection pass duration is controlled by the frequency tracking mechanism. The FlexLogic operand reflecting
the debounced state of the contact is updated at the protection pass following the validation (marks no. 3 and 4 on the fig-
ure below). The update is performed at the beginning of the protection pass so all protection and control functions, as well
as FlexLogic equations, are fed with the updated states of the contact inputs.

5 SETTINGS 5.8 INPUTS AND OUTPUTS
The FlexLogic operand response time to the contact input change is equal to the debounce time setting plus up to one pro-
tection pass (variable and depending on system frequency if frequency tracking enabled). If the change of state occurs just
after a protection pass, the recognition is delayed until the subsequent protection pass; that is, by the entire duration of the
protection pass. If the change occurs just prior to a protection pass, the state is recognized immediately. Statistically a delay
of half the protection pass is expected. Owing to the 0.5 ms scan rate, the time resolution for the input contact is below
1msec.
For example, 8 protection passes per cycle on a 60 Hz system correspond to a protection pass every 2.1 ms. With a con-
tact debounce time setting of 3.0 ms, the FlexLogic operand-assert time limits are: 3.0 + 0.0 = 3.0 ms and 3.0 + 2.1 = 5.1
ms. These time limits depend on how soon the protection pass runs after the debouncing time.
Regardless of the contact debounce time setting, the contact input event is time-stamped with a 1 s accuracy using the
time of the first scan corresponding to the new state (mark no. 2 below). Therefore, the time stamp reflects a change in the
DC voltage across the contact input terminals that was not accidental as it was subsequently validated using the debounce
timer. Keep in mind that the associated FlexLogic operand is asserted/de-asserted later, after validating the change.
The debounce algorithm is symmetrical: the same procedure and debounce time are used to filter the LOW-HIGH (marks
no.1, 2, 3, and 4 in the figure below) and HIGH-LOW (marks no. 5, 6, 7, and 8 below) transitions.
VOLTAGE
INPUT
USER-PROGRAMMABLE THRESHOLD
6
2 1 3 5
Time stamp of the first
5
TM
Time stamp of the first At this time, the The FlexLogic scan corresponding to the
At this time, the new
scan corresponding to new (HIGH) operand is going to new validated state is
(LOW) contact state is
the new validated state is contact state is be asserted at this logged in the SOE record
validated
logged in the SOE record validated protection pass
7
RAW CONTACT
The FlexLogicTM
operand is going to be
STATE
de-asserted at this
protection pass
DEBOUNCE TIME
(user setting)
4
The FlexLogicTM operand
DEBOUNCE TIME
The FlexLogicTM operand changes reflecting the
SCAN TIME (user setting)
changes reflecting the validated contact state
FLEXLOGICTM
(0.5 msec) validated contact state

OPERAND
PROTECTION PASS
(8 times a cycle controlled by the
frequency tracking mechanism)
842709A1.cdr
Figure 5–171: INPUT CONTACT DEBOUNCING MECHANISM AND TIME-STAMPING SAMPLE TIMING
Contact inputs are isolated in groups of four to allow connection of wet contacts from different voltage sources for each
group. The CONTACT INPUT THRESHOLDS determine the minimum voltage required to detect a closed contact input. This
value should be selected according to the following criteria: 17 for 24 V sources, 33 for 48 V sources, 84 for 110 to 125 V
sources and 166 for 250 V sources.
For example, to use contact input H5a as a status input from the breaker 52b contact to seal-in the trip relay and record it in
the Event Records menu, make the following settings changes:
CONTACT INPUT H5A ID: "Breaker Closed (52b)"
CONTACT INPUT H5A EVENTS: "Enabled"
Note that the 52b contact is closed when the breaker is open and open when the breaker is closed.

5.8.2 VIRTUAL INPUTS
PATH: SETTINGS  INPUTS/OUTPUTS  VIRTUAL INPUTS  VIRTUAL INPUT 1(64)
 VIRTUAL INPUT 1 VIRTUAL INPUT 1 Range: Disabled, Enabled

VIRTUAL INPUT 1 ID: Range: Up to 12 alphanumeric characters
MESSAGE
Virt Ip 1
VIRTUAL INPUT 1 Range: Self-Reset, Latched
MESSAGE
TYPE: Latched
VIRTUAL INPUT 1 Range: Disabled, Enabled
MESSAGE
EVENTS: Disabled
There are 64 virtual inputs that can be individually programmed to respond to input signals from the keypad (via the COM-
MANDS menu) and communications protocols. All virtual input operands are defaulted to “Off” (logic 0) unless the appropri-
ate input signal is received.
If the VIRTUAL INPUT x FUNCTION is to “Disabled”, the input will be forced to off (logic 0) regardless of any attempt to alter the
input. If set to “Enabled”, the input operates as shown on the logic diagram and generates output FlexLogic operands in
response to received input signals and the applied settings.
There are two types of operation: self-reset and latched. If VIRTUAL INPUT x TYPE is “Self-Reset”, when the input signal tran-
sits from off to on, the output operand will be set to on for only one evaluation of the FlexLogic equations and then return to
off. If set to “Latched”, the virtual input sets the state of the output operand to the same state as the most recent received
input.
5 The self-reset operating mode generates the output operand for a single evaluation of the FlexLogic equations. If
the operand is to be used anywhere other than internally in a FlexLogic equation, it will likely have to be lengthened
NOTE
in time. A FlexLogic timer with a delayed reset can perform this function.
SETTING
VIRTUAL INPUT 1
FUNCTION:
Enabled=1 S
AND
Latch
“Virtual Input 1 to ON = 1”
SETTING
“Virtual Input 1 to OFF = 0” R VIRTUAL INPUT 1 ID:
AND
SETTING (Flexlogic Operand)
OR
Virt Ip 1
VIRTUAL INPUT 1
TYPE:
Latched AND
Self - Reset 827080A3.CDR
Figure 5–172: VIRTUAL INPUTS SCHEME LOGIC

5.8.3 CONTACT OUTPUTS
a) DIGITAL OUTPUTS
PATH: SETTINGS  INPUTS/OUTPUTS  CONTACT OUTPUTS  CONTACT OUTPUT H1
 CONTACT OUTPUT H1 CONTACT OUTPUT H1 ID Range: Up to 12 alphanumeric characters

 Cont Op 1
OUTPUT H1 OPERATE: Range: FlexLogic operand
MESSAGE
Off
OUTPUT H1 SEAL-IN: Range: FlexLogic operand
MESSAGE
Off
CONTACT OUTPUT H1 Range: Disabled, Enabled
MESSAGE
EVENTS: Enabled
Upon startup of the relay, the main processor will determine from an assessment of the modules installed in the chassis
which contact outputs are available and present the settings for only these outputs.
An ID may be assigned to each contact output. The signal that can OPERATE a contact output may be any FlexLogic oper-
and (virtual output, element state, contact input, or virtual input). An additional FlexLogic operand may be used to SEAL-IN
the relay. Any change of state of a contact output can be logged as an Event if programmed to do so.
For example, the trip circuit current is monitored by providing a current threshold detector in series with some Form-A con-
tacts (see the trip circuit example in the Digital elements section). The monitor will set a flag (see the specifications for
Form-A). The name of the FlexLogic operand set by the monitor, consists of the output relay designation, followed by the
name of the flag; for example, CONT OP 1 ION.
In most breaker control circuits, the trip coil is connected in series with a breaker auxiliary contact used to interrupt current 5
flow after the breaker has tripped, to prevent damage to the less robust initiating contact. This can be done by monitoring
an auxiliary contact on the breaker which opens when the breaker has tripped, but this scheme is subject to incorrect oper-
ation caused by differences in timing between breaker auxiliary contact change-of-state and interruption of current in the
trip circuit. The most dependable protection of the initiating contact is provided by directly measuring current in the tripping
circuit, and using this parameter to control resetting of the initiating relay. This scheme is often called trip seal-in.
This can be realized in the D60 using the CONT OP 1 ION FlexLogic operand to seal-in the contact output as follows:
CONTACT OUTPUT H1 ID: “Cont Op 1"
OUTPUT H1 OPERATE: any suitable FlexLogic operand
OUTPUT H1 SEAL-IN: “Cont Op 1 IOn”
CONTACT OUTPUT H1 EVENTS: “Enabled”
b) LATCHING OUTPUTS
PATH: SETTINGS  INPUTS/OUTPUTS  CONTACT OUTPUTS  CONTACT OUTPUT H1a
 CONTACT OUTPUT H1a OUTPUT H1a ID Range: Up to 12 alphanumeric characters

 L-Cont Op 1
OUTPUT H1a OPERATE: Range: FlexLogic operand
MESSAGE
Off
OUTPUT H1a RESET: Range: FlexLogic operand
MESSAGE
Off
OUTPUT H1a TYPE: Range: Operate-dominant, Reset-dominant
MESSAGE
Operate-dominant
OUTPUT H1a EVENTS: Range: Disabled, Enabled
MESSAGE
Disabled

The D60 latching output contacts are mechanically bi-stable and controlled by two separate (open and close) coils. As such
they retain their position even if the relay is not powered up. The relay recognizes all latching output contact cards and pop-
ulates the setting menu accordingly. On power up, the relay reads positions of the latching contacts from the hardware
before executing any other functions of the relay (such as protection and control features or FlexLogic).
The latching output modules, either as a part of the relay or as individual modules, are shipped from the factory with all
latching contacts opened. It is highly recommended to double-check the programming and positions of the latching con-
tacts when replacing a module.
Since the relay asserts the output contact and reads back its position, it is possible to incorporate self-monitoring capabili-
ties for the latching outputs. If any latching outputs exhibits a discrepancy, the LATCHING OUTPUT ERROR self-test error is
declared. The error is signaled by the LATCHING OUT ERROR FlexLogic operand, event, and target message.
• OUTPUT H1a OPERATE: This setting specifies a FlexLogic operand to operate the ‘close coil’ of the contact. The
relay will seal-in this input to safely close the contact. Once the contact is closed and the RESET input is logic 0 (off),
any activity of the OPERATE input, such as subsequent chattering, will not have any effect. With both the OPERATE and
RESET inputs active (logic 1), the response of the latching contact is specified by the OUTPUT H1A TYPE setting.
• OUTPUT H1a RESET: This setting specifies a FlexLogic operand to operate the ‘trip coil’ of the contact. The relay will
seal-in this input to safely open the contact. Once the contact is opened and the OPERATE input is logic 0 (off), any
activity of the RESET input, such as subsequent chattering, will not have any effect. With both the OPERATE and RESET
inputs active (logic 1), the response of the latching contact is specified by the OUTPUT H1A TYPE setting.
• OUTPUT H1a TYPE: This setting specifies the contact response under conflicting control inputs; that is, when both the
OPERATE and RESET signals are applied. With both control inputs applied simultaneously, the contact will close if set to
“Operate-dominant” and will open if set to “Reset-dominant”.
Application Example 1:
5 A latching output contact H1a is to be controlled from two user-programmable pushbuttons (buttons number 1 and 2). The
following settings should be applied.
Program the Latching Outputs by making the following changes in the SETTINGS  INPUTS/OUTPUTS  CONTACT OUT-
PUTS  CONTACT OUTPUT H1a menu (assuming an H4L module):
OUTPUT H1a OPERATE: “PUSHBUTTON 1 ON”

OUTPUT H1a RESET: “PUSHBUTTON 2 ON”
Program the pushbuttons by making the following changes in the PRODUCT SETUP  USER-PROGRAMMABLE PUSHBUT-
TONS  USER PUSHBUTTON 1 and USER PUSHBUTTON 2 menus:
PUSHBUTTON 1 FUNCTION: “Self-reset” PUSHBUTTON 2 FUNCTION: “Self-reset”

PUSHBTN 1 DROP-OUT TIME: “0.00 s” PUSHBTN 2 DROP-OUT TIME: “0.00 s”
A relay, having two latching contacts H1a and H1c, is to be programmed. The H1a contact is to be a Type-a contact, while
the H1c contact is to be a Type-b contact (Type-a means closed after exercising the operate input; Type-b means closed
after exercising the reset input). The relay is to be controlled from virtual outputs: VO1 to operate and VO2 to reset.
PUTS  CONTACT OUTPUT H1a and CONTACT OUTPUT H1c menus (assuming an H4L module):
OUTPUT H1a OPERATE: “VO1” OUTPUT H1c OPERATE: “VO2”

OUTPUT H1a RESET: “VO2” OUTPUT H1c RESET: “VO1”
Since the two physical contacts in this example are mechanically separated and have individual control inputs, they will not
operate at exactly the same time. A discrepancy in the range of a fraction of a maximum operating time may occur. There-
fore, a pair of contacts programmed to be a multi-contact relay will not guarantee any specific sequence of operation (such
as make before break). If required, the sequence of operation must be programmed explicitly by delaying some of the con-
trol inputs as shown in the next application example.
A make before break functionality must be added to the preceding example. An overlap of 20 ms is required to implement
this functionality as described below:

Write the following FlexLogic equation (EnerVista UR Setup example shown):
Both timers (Timer 1 and Timer 2) should be set to 20 ms pickup and 0 ms dropout.
PUTS  CONTACT OUTPUT H1a and CONTACT OUTPUT H1c menus (assuming an H4L module):
OUTPUT H1a OPERATE: “VO1” OUTPUT H1c OPERATE: “VO2”
OUTPUT H1a RESET: “VO4” OUTPUT H1c RESET: “VO3”
A latching contact H1a is to be controlled from a single virtual output VO1. The contact should stay closed as long as VO1
is high, and should stay opened when VO1 is low. Program the relay as follows.
Write the following FlexLogic equation (EnerVista UR Setup example shown):
5
PUTS  CONTACT OUTPUT H1a menu (assuming an H4L module):
OUTPUT H1a OPERATE: “VO1”
OUTPUT H1a RESET: “VO2”
5.8.4 VIRTUAL OUTPUTS
PATH: SETTINGS  INPUTS/OUTPUTS  VIRTUAL OUTPUTS  VIRTUAL OUTPUT 1(96)
 VIRTUAL OUTPUT 1 VIRTUAL OUTPUT 1 ID Range: Up to 12 alphanumeric characters

 Virt Op 1
VIRTUAL OUTPUT 1 Range: Disabled, Enabled
MESSAGE
EVENTS: Disabled
There are 96 virtual outputs that may be assigned via FlexLogic. If not assigned, the output will be forced to ‘OFF’ (Logic 0).
An ID may be assigned to each virtual output. Virtual outputs are resolved in each pass through the evaluation of the Flex-
Logic equations. Any change of state of a virtual output can be logged as an event if programmed to do so.
For example, if Virtual Output 1 is the trip signal from FlexLogic and the trip relay is used to signal events, the settings
would be programmed as follows:

VIRTUAL OUTPUT 1 ID: "Trip"

VIRTUAL OUTPUT 1 EVENTS: "Disabled"
5.8.5 REMOTE DEVICES
a) REMOTE INPUTS AND OUTPUTS OVERVIEW

Remote inputs and outputs provide a means of exchanging digital state information between Ethernet-networked devices.
The IEC 61850 GSSE (Generic Substation State Event) and GOOSE (Generic Object Oriented Substation Event) stan-
dards are used.
The sharing of digital point state information between GSSE/GOOSE equipped relays is essentially an extension to Flex-
Logic, allowing distributed FlexLogic by making operands available to/from devices on a common communications net-
work. In addition to digital point states, GSSE/GOOSE messages identify the originator of the message and provide other
information required by the communication specification. All devices listen to network messages and capture data only from
messages that have originated in selected devices.
IEC 61850 GSSE messages are compatible with UCA GOOSE messages and contain a fixed set of digital points. IEC
61850 GOOSE messages can, in general, contain any configurable data items. When used by the remote input/output fea-
ture, IEC 61850 GOOSE messages contain the same data as GSSE messages.
Both GSSE and GOOSE messages are designed to be short, reliable, and high priority. GOOSE messages have additional
advantages over GSSE messages due to their support of VLAN (virtual LAN) and Ethernet priority tagging functionality.
The GSSE message structure contains space for 128 bit pairs representing digital point state information. The IEC 61850
specification provides 32 “DNA” bit pairs that represent the state of two pre-defined events and 30 user-defined events. All
remaining bit pairs are “UserSt” bit pairs, which are status bits representing user-definable events. The D60 implementation
provides 32 of the 96 available UserSt bit pairs.
5 The IEC 61850 specification includes features that are used to cope with the loss of communication between transmitting
and receiving devices. Each transmitting device will send a GSSE/GOOSE message upon a successful power-up, when
the state of any included point changes, or after a specified interval (the default update time) if a change-of-state has not
occurred. The transmitting device also sends a ‘hold time’ which is set greater than four times the programmed default time
required by the receiving device.
Receiving devices are constantly monitoring the communications network for messages they require, as recognized by the
identification of the originating device carried in the message. Messages received from remote devices include the mes-
sage time allowed to live. The receiving relay sets a timer assigned to the originating device to this time interval, and if it
has not received another message from this device at time-out, the remote device is declared to be non-communicating, so
it will use the programmed default state for all points from that specific remote device. If a message is received from a
remote device before the time allowed to live expires, all points for that device are updated to the states contained in the
message and the hold timer is restarted. The status of a remote device, where “Offline” indicates non-communicating, can
be displayed.
The remote input/output facility provides for 32 remote inputs and 64 remote outputs.
b) LOCAL DEVICES: ID OF DEVICE FOR TRANSMITTING GSSE MESSAGES

In a D60 relay, the device ID that represents the IEC 61850 GOOSE application ID (GoID) name string sent as part of each
GOOSE message is programmed in the SETTINGS  PRODUCT SETUP  COMMUNICATIONS  IEC 61850 PROTOCOL 
GSSE/GOOSE CONFIGURATION  TRANSMISSION  FIXED GOOSE  GOOSE ID setting.
Likewise, the device ID that represents the IEC 61850 GSSE application ID name string sent as part of each GSSE mes-
sage is programmed in the SETTINGS  PRODUCT SETUP  COMMUNICATIONS  IEC 61850 PROTOCOL  GSSE/GOOSE
CONFIGURATION  TRANSMISSION  GSSE  GSSE ID setting.
In D60 releases previous to 5.0x, these name strings were represented by the RELAY NAME setting.

c) REMOTE DEVICES: ID OF DEVICE FOR RECEIVING GSSE/GOOSE MESSAGES

PATH: SETTINGS  INPUTS/OUTPUTS  REMOTE DEVICES  REMOTE DEVICE 1(16)
 REMOTE DEVICE 1 REMOTE DEVICE 1 ID: Range: up to 20 alphanumeric characters

 Remote Device 1
REMOTE DEVICE 1 Range: 0 to 16383 in steps of 1
MESSAGE
ETYPE APPID: 0
REMOTE DEVICE 1 Range: Fixed, GOOSE 1 through GOOSE 16
MESSAGE
DATASET: Fixed
Remote devices are available for setting purposes. A receiving relay must be programmed to capture messages from only
those originating remote devices of interest. This setting is used to select specific remote devices by entering (bottom row)
the exact identification (ID) assigned to those devices.
The REMOTE DEVICE 1 ETYPE APPID setting is only used with GOOSE messages; they are not applicable to GSSE mes-
sages. This setting identifies the Ethernet application identification in the GOOSE message. It should match the corre-
sponding settings on the sending device.
The REMOTE DEVICE 1 DATASET setting provides for the choice of the D60 fixed (DNA/UserSt) dataset (that is, containing
DNA and UserSt bit pairs), or one of the configurable datasets.
Note that the dataset for the received data items must be made up of existing items in an existing logical node. For this rea-
son, logical node GGIO3 is instantiated to hold the incoming data items. GGIO3 is not necessary to make use of the
received data. The remote input data item mapping takes care of the mapping of the inputs to remote input FlexLogic oper-
ands. However, GGIO3 data can be read by IEC 61850 clients.
5.8.6 REMOTE INPUTS 5

PATH: SETTINGS  INPUTS/OUTPUTS  REMOTE INPUTS  REMOTE INPUT 1(32)
 REMOTE INPUT 1 REMOTE INPUT 1 ID: Range: up to 12 alphanumeric characters

 Remote Ip 1
REMOTE IN 1 DEVICE: Range: Remote Device 1 to Remote device 16
MESSAGE
Remote Device 1
REMOTE IN 1 ITEM: Range: None, DNA-1 to DNA-32, UserSt-1 to UserSt-32,
MESSAGE Config Item 1 to Config Item 32
None
REMOTE IN 1 DEFAULT Range: On, Off, Latest/On, Latest/Off
MESSAGE
STATE: Off
REMOTE IN 1 Range: Disabled, Enabled
MESSAGE
EVENTS: Disabled
Remote Inputs that create FlexLogic operands at the receiving relay are extracted from GSSE/GOOSE messages originat-
ing in remote devices. Each remote input can be selected from a list consisting of: DNA-1 through DNA-32, UserSt-1
through UserSt-32, and Dataset Item 1 through Dataset Item 32. The function of DNA inputs is defined in the IEC 61850
specification and is presented in the IEC 61850 DNA Assignments table in the Remote outputs section. The function of
UserSt inputs is defined by the user selection of the FlexLogic operand whose state is represented in the GSSE/GOOSE
message. A user must program a DNA point from the appropriate FlexLogic operand.
Remote input 1 must be programmed to replicate the logic state of a specific signal from a specific remote device for local
use. This programming is performed via the three settings shown above.
The REMOTE INPUT 1 ID setting allows the user to assign descriptive text to the remote input. The REMOTE IN 1 DEVICE setting
selects the remote device which originates the required signal, as previously assigned to the remote device via the setting
REMOTE DEVICE (16) ID (see the Remote devices section). The REMOTE IN 1 ITEM setting selects the specific bits of the
GSSE/GOOSE message required.
The REMOTE IN 1 DEFAULT STATE setting selects the logic state for this point if the local relay has just completed startup or
the remote device sending the point is declared to be non-communicating. The following choices are available:

• Setting REMOTE IN 1 DEFAULT STATE to “On” value defaults the input to logic 1.
• Setting REMOTE IN 1 DEFAULT STATE to “Off” value defaults the input to logic 0.
• Setting REMOTE IN 1 DEFAULT STATE to “Latest/On” freezes the input in case of lost communications. If the latest state is
not known, such as after relay power-up but before the first communication exchange, the input will default to logic 1.
When communication resumes, the input becomes fully operational.
• Setting REMOTE IN 1 DEFAULT STATE to “Latest/Off” freezes the input in case of lost communications. If the latest state is
not known, such as after relay power-up but before the first communication exchange, the input will default to logic 0.
When communication resumes, the input becomes fully operational.
For additional information on GSSE/GOOOSE messaging, refer to the Remote Devices section in this chapter.
NOTE
5.8.7 REMOTE DOUBLE-POINT STATUS INPUTS
PATH: SETTINGS  INPUTS/OUTPUTS  REMOTE DPS INPUTS  REMOTE DPS INPUT 1(5)
 REMOTE DPS INPUT 1 REM DPS IN 1 ID: Range: up to 12 alphanumeric characters

 RemDPS Ip 1
REM DPS IN 1 DEV: Range: Remote Device 1 to Remote device 16
MESSAGE
Remote Device 1
REM DPS IN 1 ITEM: Range: None, Dataset Item 1 to Dataset Item 32
MESSAGE
None
REM DPS IN 1 Range: Enabled, Disabled
5
MESSAGE
EVENTS: Disabled
Remote double-point status inputs are extracted from GOOSE messages originating in the remote device. Each remote
double point status input must be programmed to replicate the logic state of a specific signal from a specific remote device
for local use. This functionality is accomplished with the five remote double-point status input settings.
• REM DPS IN 1 ID: This setting assigns descriptive text to the remote double-point status input.
• REM DPS IN 1 DEV: This setting selects a remote device ID to indicate the origin of a GOOSE message. The range is
selected from the remote device IDs specified in the Remote devices section.
• REM DPS IN 1 ITEM: This setting specifies the required bits of the GOOSE message.
The configurable GOOSE dataset items must be changed to accept a double-point status item from a GOOSE dataset
(changes are made in the SETTINGS  COMMUNICATION  IEC 61850 PROTOCOL  GSSE/GOOSE CONFIGURATION 
RECEPTION  CONFIGURABLE GOOSE  CONFIGURABLE GOOSE 1(16)  CONFIG GSE 1 DATASET ITEMS menus). Dataset
items configured to receive any of “GGIO3.ST.IndPos1.stV” to “GGIO3.ST.IndPos5.stV” will accept double-point status
information that will be decoded by the remote double-point status inputs configured to this dataset item.
The remote double point status is recovered from the received IEC 61850 dataset and is available as through the RemDPS
Ip 1 BAD, RemDPS Ip 1 INTERM, RemDPS Ip 1 OFF, and RemDPS Ip 1 ON FlexLogic operands. These operands can then be
used in breaker or disconnect control schemes.
5.8.8 REMOTE OUTPUTS
a) DNA BIT PAIRS

PATH: SETTINGS  INPUTS/OUTPUTS  REMOTE OUTPUTS DNA BIT PAIRS  REMOTE OUTPUTS DNA- 1(32) BIT PAIR
 REMOTE OUTPUTS DNA- 1 OPERAND: Range: FlexLogic operand

 DNA- 1 BIT PAIR Off
DNA- 1 EVENTS: Range: Disabled, Enabled
MESSAGE
Disabled

Remote outputs (1 to 32) are FlexLogic operands inserted into GSSE/GOOSE messages that are transmitted to remote
devices on a LAN. Each digital point in the message must be programmed to carry the state of a specific FlexLogic oper-
and. The above operand setting represents a specific DNA function (as shown in the following table) to be transmitted.
Table 5–34: IEC 61850 DNA ASSIGNMENTS

DNA IEC 61850 DEFINITION FLEXLOGIC OPERAND
1 Test IEC 61850 TEST MODE
2 ConfRev IEC 61850 CONF REV
b) USERST BIT PAIRS

PATH: SETTINGS  INPUTS/OUTPUTS  REMOTE OUTPUTS UserSt BIT PAIRS  REMOTE OUTPUTS UserSt- 1(32) BIT PAIR
 REMOTE OUTPUTS UserSt- 1 OPERAND: Range: FlexLogic operand

 UserSt- 1 BIT PAIR Off
UserSt- 1 EVENTS: Range: Disabled, Enabled
MESSAGE
Disabled
Remote outputs 1 to 32 originate as GSSE/GOOSE messages to be transmitted to remote devices. Each digital point in the
message must be programmed to carry the state of a specific FlexLogic operand. The setting above is used to select the
operand which represents a specific UserSt function (as selected by the user) to be transmitted.
For more information on GSSE/GOOSE messaging, refer to Remote Inputs/Outputs Overview in the Remote
Devices section.
NOTE
5.8.9 RESETTING
5
PATH: SETTINGS  INPUTS/OUTPUTS  RESETTING
 RESETTING RESET OPERAND: Range: FlexLogic operand

 Off
Some events can be programmed to latch the faceplate LED event indicators and the target message on the display. Once
set, the latching mechanism will hold all of the latched indicators or messages in the set state after the initiating condition
has cleared until a RESET command is received to return these latches (not including FlexLogic latches) to the reset state.
The RESET command can be sent from the faceplate Reset button, a remote device via a communications channel, or any
programmed operand.
When the RESET command is received by the relay, two FlexLogic operands are created. These operands, which are
stored as events, reset the latches if the initiating condition has cleared. The three sources of RESET commands each cre-
ate the RESET OP FlexLogic operand. Each individual source of a RESET command also creates its individual operand
RESET OP (PUSHBUTTON), RESET OP (COMMS) or RESET OP (OPERAND) to identify the source of the command. The setting
shown above selects the operand that will create the RESET OP (OPERAND) operand.

5.8.10 DIRECT INPUTS AND OUTPUTS
a) DIRECT INPUTS
PATH: SETTINGS  INPUTS/OUTPUTS  DIRECT INPUTS  DIRECT INPUT 1(32)
 DIRECT INPUT 1 DIRECT INPUT 1 Range: up to 12 alphanumeric characters

 NAME: Dir Ip 1
DIRECT INPUT 1 Range: 1 to 16
MESSAGE
DEVICE ID: 1
DIRECT INPUT 1 Range: 1 to 32
MESSAGE
BIT NUMBER: 1
DIRECT INPUT 1 Range: On, Off, Latest/On, Latest/Off
MESSAGE
DEFAULT STATE: Off
DIRECT INPUT 1 Range: Enabled, Disabled
MESSAGE
EVENTS: Disabled
These settings specify how the direct input information is processed. The DIRECT INPUT 1 NAME setting allows the user to
assign a descriptive name to the direct input. The DIRECT INPUT 1 DEVICE ID represents the source of direct input 1. The
specified direct input is driven by the device identified here.
The DIRECT INPUT 1 BIT NUMBER is the bit number to extract the state for direct input 1. Direct Input 1 is driven by the bit
identified as DIRECT INPUT 1 BIT NUMBER. This corresponds to the direct output number of the sending device.
The DIRECT INPUT 1 DEFAULT STATE represents the state of the direct input when the associated direct device is offline. The
5 following choices are available:

• Setting DIRECT INPUT 1 DEFAULT STATE to “On” value defaults the input to Logic 1.
• Setting DIRECT INPUT 1 DEFAULT STATE to “Off” value defaults the input to Logic 0.
• Setting DIRECT INPUT 1 DEFAULT STATE to “Latest/On” freezes the input in case of lost communications. If the latest
state is not known, such as after relay power-up but before the first communication exchange, the input will default to
Logic 1. When communication resumes, the input becomes fully operational.
• Setting DIRECT INPUT 1 DEFAULT STATE to “Latest/Off” freezes the input in case of lost communications. If the latest
state is not known, such as after relay power-up but before the first communication exchange, the input will default to
Logic 0. When communication resumes, the input becomes fully operational.
b) DIRECT OUTPUTS
PATH: SETTINGS  INPUTS/OUTPUTS  DIRECT OUTPUTS  DIRECT OUTPUT 1(32)
 DIRECT OUTPUT 1 DIRECT OUT 1 NAME: Range: up to 12 alphanumeric characters

 Dir Out 1
DIRECT OUT 1 OPERAND: Range: FlexLogic operand
MESSAGE
Off
DIRECT OUTPUT 1 Range: Enabled, Disabled
MESSAGE
EVENTS: Disabled
The DIRECT OUT 1 NAME setting allows the user to assign a descriptive name to the direct output. The DIR OUT 1 OPERAND is
the FlexLogic operand that determines the state of this direct output.
c) APPLICATION EXAMPLES
The examples introduced in the earlier Direct inputs and outputs section (part of the Product Setup section) are continued
below to illustrate usage of the direct inputs and outputs.

EXAMPLE 1: EXTENDING INPUT/OUTPUT CAPABILITIES OF A D60 RELAY

Consider an application that requires additional quantities of digital inputs or output contacts or lines of programmable logic
that exceed the capabilities of a single UR-series chassis. The problem is solved by adding an extra UR-series IED, such
as the C30, to satisfy the additional inputs/outputs and programmable logic requirements. The two IEDs are connected via
single-channel digital communication cards as shown below.
TX1
UR IED 1
RX1
TX1
UR IED 2
RX1
Figure 5–173: INPUT AND OUTPUT EXTENSION VIA DIRECT INPUTS AND OUTPUTS
Assume contact input 1 from UR IED 2 is to be used by UR IED 1. The following settings should be applied (Direct Input 5
and bit number 12 are used, as an example):
UR IED 1: DIRECT INPUT 5 DEVICE ID = “2” UR IED 2: DIRECT OUT 12 OPERAND = “Cont Ip 1 On”
DIRECT INPUT 5 BIT NUMBER = “12”
The Cont Ip 1 On operand of UR IED 2 is now available in UR IED 1 as DIRECT INPUT 5 ON.
EXAMPLE 2: INTERLOCKING BUSBAR PROTECTION
A simple interlocking busbar protection scheme can be accomplished by sending a blocking signal from downstream
devices, say 2, 3 and 4, to the upstream device that monitors a single incomer of the busbar, as shown in the figure below.
5
UR IED 1 BLOCK
UR IED 2 UR IED 3 UR IED 4
842712A1.CDR
Figure 5–174: SAMPLE INTERLOCKING BUSBAR PROTECTION SCHEME

Assume that Phase Instantaneous Overcurrent 1 is used by Devices 2, 3, and 4 to block Device 1. If not blocked, Device 1
would trip the bus upon detecting a fault and applying a short coordination time delay.
The following settings should be applied (assume Bit 3 is used by all 3 devices to send the blocking signal and Direct Inputs
7, 8, and 9 are used by the receiving device to monitor the three blocking signals):
UR IED 2: DIRECT OUT 3 OPERAND: "PHASE IOC1 OP"
UR IED 1: DIRECT INPUT 7 DEVICE ID: "2"

DIRECT INPUT 7 BIT NUMBER: "3"
DIRECT INPUT 7 DEFAULT STATE: select "On" for security, select "Off" for dependability
DIRECT INPUT 8 DEVICE ID: "3"



Now the three blocking signals are available in UR IED 1 as DIRECT INPUT 7 ON, DIRECT INPUT 8 ON, and DIRECT INPUT 9
ON. Upon losing communications or a device, the scheme is inclined to block (if any default state is set to “On”), or to trip
the bus on any overcurrent condition (all default states set to “Off”).
EXAMPLE 2: PILOT-AIDED SCHEMES
Consider a three-terminal line protection application shown in the figure below.
UR IED 1 UR IED 2
UR IED 3
842713A1.CDR
Figure 5–175: THREE-TERMINAL LINE APPLICATION

Assume the Hybrid Permissive Overreaching Transfer Trip (Hybrid POTT) scheme is applied using the architecture shown
below. The scheme output operand HYB POTT TX1 is used to key the permission.
5
TX1 RX1 RX2
UR IED 1 UR IED 2
RX1 TX1 TX2
RX1
UR IED 3
TX1
842714A1.CDR
Figure 5–176: SINGLE-CHANNEL OPEN-LOOP CONFIGURATION

In the above architecture, Devices 1 and 3 do not communicate directly. Therefore, Device 2 must act as a ‘bridge’. The fol-
lowing settings should be applied:
UR IED 1: DIRECT OUT 2 OPERAND: "HYB POTT TX1"
DIRECT INPUT 5 BIT NUMBER: "2" (this is a message from IED 2)
DIRECT INPUT 6 BIT NUMBER: "4" (effectively, this is a message from IED 3)
UR IED 3: DIRECT OUT 2 OPERAND: "HYB POTT TX1"
DIRECT INPUT 5 BIT NUMBER: "2" (this is a message from IED 2)
DIRECT INPUT 6 BIT NUMBER: "3" (effectively, this is a message from IED 1)
UR IED 2: DIRECT INPUT 5 DEVICE ID: "1"

DIRECT OUT 2 OPERAND: "HYB POTT TX1"

DIRECT OUT 3 OPERAND: "DIRECT INPUT 5" (forward a message from 1 to 3)
DIRECT OUT 4 OPERAND: "DIRECT INPUT 6" (forward a message from 3 to 1)
Signal flow between the three IEDs is shown in the figure below:
UR IED 1 UR IED 2
DIRECT OUT 2 = HYB POTT TX1 DIRECT INPUT 5
DIRECT INPUT 5 DIRECT OUT 2 = HYB POTT TX1
DIRECT INPUT 6 DIRECT OUT 4 = DIRECT INPUT 6
DIRECT OUT 3 = DIRECT INPUT 5
DIRECT INPUT 6
UR IED 3 DIRECT INPUT 5

DIRECT INPUT 6
DIRECT OUT 2 = HYB POTT TX1
842717A1.CDR
Figure 5–177: SIGNAL FLOW FOR DIRECT INPUT AND OUTPUT – EXAMPLE 3
In three-terminal applications, both the remote terminals must grant permission to trip. Therefore, at each terminal, direct
inputs 5 and 6 should be ANDed in FlexLogic and the resulting operand configured as the permission to trip (HYB POTT RX1
setting).
5.8.11 TELEPROTECTION INPUTS AND OUTPUTS
a) OVERVIEW
5
The relay provides sixteen teleprotection inputs on communications channel 1 (numbered 1-1 through 1-16) and sixteen
teleprotection inputs on communications channel 2 (on two-terminals two-channel and three-terminal systems only, num-
bered 2-1 through 2-16). The remote relay connected to channels 1 and 2 of the local relay is programmed by assigning
FlexLogic operands to be sent via the selected communications channel. This allows the user to create distributed protec-
tion and control schemes via dedicated communications channels. Some examples are directional comparison pilot
schemes and direct transfer tripping. It should be noted that failures of communications channels will affect teleprotection
functionality. The teleprotection function must be enabled to utilize the inputs.
b) TELEPROTECTION INPUTS
PATH: SETTINGS  INPUTS/OUTPUTS  TELEPROTECTION  TELEPROT INPUTS
 TELEPROT INPUTS TELEPROT INPUT 1-1 Range: Off, On, Latest/Off, Latest/On
 DEFAULT: Off
TELEPROT INPUT 1-2 Range: Off, On, Latest/Off, Latest/On
MESSAGE
DEFAULT: Off


MESSAGE
DEFAULT: Off
MESSAGE
DEFAULT: Off
MESSAGE
DEFAULT: Off


MESSAGE
DEFAULT: Off

Setting the TELEPROT INPUT ~~ DEFAULT setting to “On” defaults the input to logic 1 when the channel fails. A value of “Off”
defaults the input to logic 0 when the channel fails.
The “Latest/On” and “Latest/Off” values freeze the input in case of lost communications. If the latest state is not known,
such as after relay power-up but before the first communication exchange, then the input defaults to logic 1 for “Latest/On”
and logic 0 for “Latest/Off”.
c) TELEPROTECTION OUTPUTS
PATH: SETTINGS  INPUTS/OUTPUTS  TELEPROTECTION  TELEPROT OUTPUTS
 TELEPROT OUTPUTS TELEPROT OUTPUT 1-1: Range: FlexLogic operand

 Off
TELEPROT OUTPUT 1-2: Range: FlexLogic operand
MESSAGE
Off


MESSAGE
Off
MESSAGE
Off
MESSAGE
Off

5 MESSAGE
TELEPROT OUTPUT 2-16:
Off
As the following figure demonstrates, processing of the teleprotection inputs/outputs is dependent on the number of com-
munication channels and terminals. On two-terminal two-channel systems, they are processed continuously on each chan-
nel and mapped separately per channel. Therefore, to achieve redundancy, the user must assign the same operand on
both channels (teleprotection outputs at the sending end or corresponding teleprotection inputs at the receiving end). On
three-terminal two-channel systems, redundancy is achieved by programming signal re-transmittal in the case of channel
failure between any pair of relays.

UR-1 UR-2
ACTUAL VALUES SETTING
CHANNEL 1 STATUS: TELEPROT INPUT 1-1
DEFAULT:
SETTING (same for 1-2...1-16)
(same for 1-2...1-16) On FLEXLOGIC OPERAND
Fail
Off (Flexlogic Operand) Off TELEPRO INPUT 1-1 On
OK OR
(same for 1-2...1-16)
SETTING ACTUAL VALUES

TELEPROT INPUT 1-1 CHANNEL 1 STATUS:
DEFAULT:
Communication channel #1
(same for 1-2...1-16) (Teleprotection I/O Enabled) SETTING
FLEXLOGIC OPERAND TELEPROT OUTPUT 1-1:
On (same for 1-2...1-16)
TELEPRO INPUT 1-1 On Fail
OR Off Off (Flexlogic Operand)
(same for 1-2...1-16) OK
UR-2 or UR-3
ACTUAL VALUES SETTING
CHANNEL 2 STATUS: TELEPROT INPUT 2-1
DEFAULT:
SETTING (same for 2-2...2-16)
(same for 1-2...1-16) On FLEXLOGIC OPERAND
Fail
Off TELEPRO INPUT 2-1 On
Off (Flexlogic Operand) OK OR
(same for 2-2...2-16)
SETTING ACTUAL VALUES

CHANNEL 2 STATUS:
TELEPROT INPUT 2-1 Communication channel #2
DEFAULT:
(same for 1-2...1-16) (On 3-terminal system or 2-terminal SETTING
FLEXLOGIC OPERAND
with redundant channel)
On (same for 2-2...2-16)
TELEPRO INPUT 2-1 On Fail
Off
(same for 1-2...1-16) OR OK Off (Flexlogic Operand)
842750A2.CDR
Figure 5–178: TELEPROTECTION INPUT/OUTPUT PROCESSING
5.8.12 IEC 61850 GOOSE ANALOGS

5
PATH: SETTINGS  INPUTS/OUTPUTS  IEC 61850 GOOSE ANALOGS  GOOSE ANALOG INPUT 1(32)
 GOOSE ANALOG ANALOG 1 DEFAULT: Range: –1000000.000 to 1000000.000 in steps of 0.001

 INPUT 1 1000.000
ANALOG 1 DEFAULT Range: Default Value, Last Known
MESSAGE
MODE: Default Value
GOOSE ANALOG 1 Range: up to 4 alphanumeric characters
MESSAGE
UNITS:
GOOSE ANALOG 1 PU: Range: 0.000 to 1000000000.000 in steps of 0.001
MESSAGE
1.000
The IEC 61850 GOOSE analog inputs feature allows the transmission of analog values between any two UR-series
devices. The following settings are available for each GOOSE analog input.
• ANALOG 1 DEFAULT: This setting specifies the value of the GOOSE analog input when the sending device is offline
and the ANALOG 1 DEFAULT MODE is set to “Default Value”.This setting is stored as an IEEE 754 / IEC 60559 floating
point number. Because of the large range of this setting, not all possible values can be stored. Some values may be
rounded to the closest possible floating point number.
• ANALOG 1 DEFAULT MODE: When the sending device is offline and this setting is “Last Known”, the value of the
GOOSE analog input remains at the last received value. When the sending device is offline and this setting value is
“Default Value”, then the value of the GOOSE analog input is defined by the ANALOG 1 DEFAULT setting.
• GOOSE ANALOG 1 UNITS: This setting specifies a four-character alphanumeric string that can is used in the actual
values display of the corresponding GOOSE analog input value.
• GOOSE ANALOG 1 PU: This setting specifies the per-unit base factor when using the GOOSE analog input FlexAna-
log values in other D60 features, such as FlexElements. The base factor is applied to the GOOSE analog input Flex-
Analog quantity to normalize it to a per-unit quantity. The base units are described in the following table.

Table 5–35: GOOSE ANALOG INPUT BASE UNITS

ELEMENT BASE UNITS
RTDs BASE = 100°C
(Max Delta Volts)
The GOOSE analog input FlexAnalog values are available for use in other D60 functions that use FlexAnalog values.
5.8.13 IEC 61850 GOOSE INTEGERS
5 PATH: SETTINGS  INPUTS/OUTPUTS  IEC 61850 GOOSE UINTEGERS  GOOSE UINTEGER INPUT 1(16)
 GOOSE UINTEGER UINTEGER 1 DEFAULT: Range: 0 to 429496295 in steps of 1

 INPUT 1 1000
UINTEGER 1 DEFAULT Range: Default Value, Last Known
MESSAGE
MODE: Default Value
The IEC 61850 GOOSE uinteger inputs feature allows the transmission of FlexInteger values between any two UR-series
devices. The following settings are available for each GOOSE uinteger input.
• UINTEGER 1 DEFAULT: This setting specifies the value of the GOOSE uinteger input when the sending device is
offline and the UINTEGER 1 DEFAULT MODE is set to “Default Value”.This setting is stored as a 32-bit unsigned integer
number.
• UINTEGER 1 DEFAULT MODE: When the sending device is offline and this setting is “Last Known”, the value of the
GOOSE uinteger input remains at the last received value. When the sending device is offline and this setting value is
“Default Value”, then the value of the GOOSE uinteger input is defined by the UINTEGER 1 DEFAULT setting.
The GOOSE integer input FlexInteger values are available for use in other D60 functions that use FlexInteger values.

5 SETTINGS 5.9 TRANSDUCER INPUTS AND OUTPUTS
5.9TRANSDUCER INPUTS AND OUTPUTS 5.9.1 DCMA INPUTS
PATH: SETTINGS  TRANSDUCER I/O  DCMA INPUTS  DCMA INPUT H1(W8)
 DCMA INPUT H1 DCMA INPUT H1 Range: Disabled, Enabled

DCMA INPUT H1 ID: Range: up to 20 alphanumeric characters
MESSAGE
DCMA Ip 1
DCMA INPUT H1 Range: 6 alphanumeric characters
MESSAGE
UNITS: A
DCMA INPUT H1 Range: 0 to –1 mA, 0 to +1 mA, –1 to +1 mA, 0 to 5 mA,
MESSAGE 0 to 10mA, 0 to 20 mA, 4 to 20 mA
RANGE: 0 to -1 mA
DCMA INPUT H1 MIN Range: –9999.999 to +9999.999 in steps of 0.001
MESSAGE
VALUE: 0.000
DCMA INPUT H1 MAX Range: –9999.999 to +9999.999 in steps of 0.001
MESSAGE
VALUE: 0.000
Hardware and software is provided to receive signals from external transducers and convert these signals into a digital for-
mat for use as required. The relay will accept inputs in the range of –1 to +20 mA DC, suitable for use with most common
transducer output ranges; all inputs are assumed to be linear over the complete range. Specific hardware details are con-
tained in chapter 3.
Before the dcmA input signal can be used, the value of the signal measured by the relay must be converted to the range
and quantity of the external transducer primary input parameter, such as DC voltage or temperature. The relay simplifies
this process by internally scaling the output from the external transducer and displaying the actual primary parameter.
5
dcmA input channels are arranged in a manner similar to CT and VT channels. The user configures individual channels
with the settings shown here.
The channels are arranged in sub-modules of two channels, numbered from 1 through 8 from top to bottom. On power-up,
the relay will automatically generate configuration settings for every channel, based on the order code, in the same general
manner that is used for CTs and VTs. Each channel is assigned a slot letter followed by the row number, 1 through 8 inclu-
sive, which is used as the channel number. The relay generates an actual value for each available input channel.
Settings are automatically generated for every channel available in the specific relay as shown above for the first channel of
a type 5F transducer module installed in slot H.
The function of the channel may be either “Enabled” or “Disabled”. If “Disabled”, no actual values are created for the chan-
nel. An alphanumeric “ID” is assigned to each channel; this ID will be included in the channel actual value, along with the
programmed units associated with the parameter measured by the transducer, such as volts, °C, megawatts, etc. This ID is
also used to reference the channel as the input parameter to features designed to measure this type of parameter. The
DCMA INPUT H1 RANGE setting specifies the mA DC range of the transducer connected to the input channel.
The DCMA INPUT H1 MIN VALUE and DCMA INPUT H1 MAX VALUE settings are used to program the span of the transducer in
primary units. For example, a temperature transducer might have a span from 0 to 250°C; in this case the DCMA INPUT H1
MIN VALUE value is “0” and the DCMA INPUT H1 MAX VALUE value is “250”. Another example would be a watts transducer with
a span from –20 to +180 MW; in this case the DCMA INPUT H1 MIN VALUE value would be “–20” and the DCMA INPUT H1 MAX
VALUE value “180”. Intermediate values between the min and max values are scaled linearly.

5.9 TRANSDUCER INPUTS AND OUTPUTS 5 SETTINGS
5.9.2 RTD INPUTS
PATH: SETTINGS  TRANSDUCER I/O  RTD INPUTS  RTD INPUT H1(W8)
 RTD INPUT H1 RTD INPUT H1 Range: Disabled, Enabled

RTD INPUT H1 ID: Range: Up to 20 alphanumeric characters
MESSAGE
RTD Ip 1
RTD INPUT H1 TYPE: Range: 100Ω Nickel, 10Ω Copper, 100Ω Platinum,
MESSAGE 120Ω Nickel
100Ω Nickel
Hardware and software is provided to receive signals from external resistance temperature detectors and convert these
signals into a digital format for use as required. These channels are intended to be connected to any of the RTD types in
common use. Specific hardware details are contained in chapter 3.
RTD input channels are arranged in a manner similar to CT and VT channels. The user configures individual channels with
the settings shown here.
The channels are arranged in sub-modules of two channels, numbered from 1 through 8 from top to bottom. On power-up,
the relay will automatically generate configuration settings for every channel, based on the order code, in the same general
manner that is used for CTs and VTs. Each channel is assigned a slot letter followed by the row number, 1 through 8 inclu-
sive, which is used as the channel number. The relay generates an actual value for each available input channel.
Settings are automatically generated for every channel available in the specific relay as shown above for the first channel of
a type 5C transducer module installed in the first available slot.
The function of the channel may be either “Enabled” or “Disabled”. If “Disabled”, there will not be an actual value created for
5 the channel. An alphanumeric ID is assigned to the channel; this ID will be included in the channel actual values. It is also
used to reference the channel as the input parameter to features designed to measure this type of parameter. Selecting the
type of RTD connected to the channel configures the channel.
Actions based on RTD overtemperature, such as trips or alarms, are done in conjunction with the FlexElements feature. In
FlexElements, the operate level is scaled to a base of 100°C. For example, a trip level of 150°C is achieved by setting the
operate level at 1.5 pu. FlexElement operands are available to FlexLogic for further interlocking or to operate an output
contact directly.
Refer to the following table for reference temperature values for each RTD type.

Table 5–36: RTD TEMPERATURE VS. RESISTANCE

TEMPERATURE RESISTANCE (IN OHMS)
°C °F 100 Ω PT 120 Ω NI 100 Ω NI 10 Ω CU
(DIN 43760)
–50 –58 80.31 86.17 71.81 7.10
–40 –40 84.27 92.76 77.30 7.49
–30 –22 88.22 99.41 82.84 7.88
–20 –4 92.16 106.15 88.45 8.26
–10 14 96.09 113.00 94.17 8.65
0 32 100.00 120.00 100.00 9.04
10 50 103.90 127.17 105.97 9.42
20 68 107.79 134.52 112.10 9.81
30 86 111.67 142.06 118.38 10.19
40 104 115.54 149.79 124.82 10.58
50 122 119.39 157.74 131.45 10.97
60 140 123.24 165.90 138.25 11.35
70 158 127.07 174.25 145.20 11.74
80 176 130.89 182.84 152.37 12.12
90 194 134.70 191.64 159.70 12.51
100 212 138.50 200.64 167.20 12.90
110 230 142.29 209.85 174.87 13.28
120
130
248
266
146.06
149.82
219.29
228.96
182.75
190.80
13.67
14.06
5
140 284 153.58 238.85 199.04 14.44
150 302 157.32 248.95 207.45 14.83
160 320 161.04 259.30 216.08 15.22
170 338 164.76 269.91 224.92 15.61
180 356 168.47 280.77 233.97 16.00
190 374 172.46 291.96 243.30 16.39
200 392 175.84 303.46 252.88 16.78
210 410 179.51 315.31 262.76 17.17
220 428 183.17 327.54 272.94 17.56
230 446 186.82 340.14 283.45 17.95
240 464 190.45 353.14 294.28 18.34
250 482 194.08 366.53 305.44 18.73

5.9.3 DCMA OUTPUTS
PATH: SETTINGS  TRANSDUCER I/O  DCMA OUTPUTS  DCMA OUTPUT H1(W8)
 DCMA OUTPUT H1 DCMA OUTPUT H1 Range: Off, any analog actual value parameter
 SOURCE: Off
DCMA OUTPUT H1 Range: –1 to 1 mA, 0 to 1 mA, 4 to 20 mA
MESSAGE
RANGE: –1 to 1 mA
DCMA OUTPUT H1 Range: –90.000 to 90.000 pu in steps of 0.001
MESSAGE
MIN VAL: 0.000 pu
DCMA OUTPUT H1 Range: –90.000 to 90.000 pu in steps of 0.001
MESSAGE
MAX VAL: 1.000 pu
Hardware and software is provided to generate dcmA signals that allow interfacing with external equipment. Specific hard-
ware details are contained in chapter 3. The dcmA output channels are arranged in a manner similar to transducer input or
CT and VT channels. The user configures individual channels with the settings shown below.
The channels are arranged in sub-modules of two channels, numbered 1 through 8 from top to bottom. On power-up, the
relay automatically generates configuration settings for every channel, based on the order code, in the same manner used
for CTs and VTs. Each channel is assigned a slot letter followed by the row number, 1 through 8 inclusive, which is used as
the channel number.
Both the output range and a signal driving a given output are user-programmable via the following settings menu (an exam-
ple for channel M5 is shown).
5 The relay checks the driving signal (x in equations below) for the minimum and maximum limits, and subsequently re-
scales so the limits defined as MIN VAL and MAX VAL match the output range of the hardware defined as RANGE. The follow-
ing equation is applied:
 I min if x  MIN VAL


I out =  I max if x  MAX VAL (EQ 5.32)

 k  x – MIN VAL  + I min otherwise
where: x is a driving signal specified by the SOURCE setting

Imin and Imax are defined by the RANGE setting
k is a scaling constant calculated as:
I max – I min
k = ------------------------------------------------- (EQ 5.33)
MAX VAL – MIN VAL
The feature is intentionally inhibited if the MAX VAL and MIN VAL settings are entered incorrectly, e.g. when MAX VAL – MIN
VAL< 0.1 pu. The resulting characteristic is illustrated in the following figure.
Imax
OUTPUT CURRENT
Imin
DRIVING SIGNAL
MIN VAL MAX VAL 842739A1.CDR
Figure 5–179: DCMA OUTPUT CHARACTERISTIC

The dcmA output settings are described below.

• DCMA OUTPUT H1 SOURCE: This setting specifies an internal analog value to drive the analog output. Actual values
(FlexAnalog parameters) such as power, current amplitude, voltage amplitude, power factor, etc. can be configured as
sources driving dcmA outputs. Refer to Appendix A for a complete list of FlexAnalog parameters.
• DCMA OUTPUT H1 RANGE: This setting allows selection of the output range. Each dcmA channel may be set inde-
pendently to work with different ranges. The three most commonly used output ranges are available.
• DCMA OUTPUT H1 MIN VAL: This setting allows setting the minimum limit for the signal that drives the output. This
setting is used to control the mapping between an internal analog value and the output current. The setting is entered
in per-unit values. The base units are defined in the same manner as the FlexElement base units.
• DCMA OUTPUT H1 MAX VAL: This setting allows setting the maximum limit for the signal that drives the output. This
setting is used to control the mapping between an internal analog value and the output current. The setting is entered
in per-unit values. The base units are defined in the same manner as the FlexElement base units.
The DCMA OUTPUT H1 MIN VAL and DCMA OUTPUT H1 MAX VAL settings are ignored for power factor base units (i.e. if
the DCMA OUTPUT H1 SOURCE is set to FlexAnalog value based on power factor measurement).
NOTE
Three application examples are described below.

EXAMPLE: POWER MONITORING
A three phase active power on a 13.8 kV system measured via UR-series relay source 1 is to be monitored by the dcmA H1
output of the range of –1 to 1 mA. The following settings are applied on the relay: CT ratio = 1200:5, VT secondary 115, VT
connection is delta, and VT ratio = 120. The nominal current is 800 A primary and the nominal power factor is 0.90. The
power is to be monitored in both importing and exporting directions and allow for 20% overload compared to the nominal.
The nominal three-phase power is:
5
P = 3  13.8 kV  0.8 kA  0.9 = 17.21 MW (EQ 5.34)
The three-phase power with 20% overload margin is:

P max = 1.2  17.21 MW = 20.65 MW (EQ 5.35)
The base unit for power (refer to the FlexElements section in this chapter for additional details) is:
P BASE = 115 V  120  1.2 kA = 16.56 MW (EQ 5.36)
The minimum and maximum power values to be monitored (in pu) are:
– 20.65 MW 20.65 MW
minimum power = ------------------------------ = – 1.247 pu, maximum power = --------------------------- = 1.247 pu (EQ 5.37)
16.56 MW 16.56 MW
The following settings should be entered:
DCMA OUTPUT H1 SOURCE: “SRC 1 P”
DCMA OUTPUT H1 RANGE: “–1 to 1 mA”
DCMA OUTPUT H1 MIN VAL: “–1.247 pu”
DCMA OUTPUT H1 MAX VAL: “1.247 pu”
With the above settings, the output will represent the power with the scale of 1 mA per 20.65 MW. The worst-case error for
this application can be calculated by superimposing the following two sources of error:
• ±0.5% of the full scale for the analog output module, or  0.005   1 –  – 1    20.65 MW =  0.207 MW
• ±1% of reading error for the active power at power factor of 0.9
For example at the reading of 20 MW, the worst-case error is 0.01  20 MW + 0.207 MW = 0.407 MW.
EXAMPLE: CURRENT MONITORING
The phase A current (true RMS value) is to be monitored via the H2 current output working with the range from 4 to 20 mA.
The CT ratio is 5000:5 and the maximum load current is 4200 A. The current should be monitored from 0 A upwards, allow-
ing for 50% overload.
The phase current with the 50% overload margin is:

I max = 1.5  4.2 kA = 6.3 kA (EQ 5.38)
The base unit for current (refer to the FlexElements section in this chapter for additional details) is:
I BASE = 5 kA (EQ 5.39)
The minimum and maximum power values to be monitored (in pu) are:
0 kA 6.3 kA
minimum current = ------------ = 0 pu, maximum current = ----------------- = 1.26 pu (EQ 5.40)
5 kA 5 kA
DCMA OUTPUT H2 SOURCE: “SRC 1 Ia RMS”
DCMA OUTPUT H2 RANGE: “4 to 20 mA”
DCMA OUTPUT H2 MIN VAL: “0.000 pu”
The worst-case error for this application could be calculated by superimposing the following two sources of error:
• ±0.5% of the full scale for the analog output module, or  0.005   20 – 4   6.3 kA =  0.504 kA
• ±0.25% of reading or ±0.1% of rated (whichever is greater) for currents between 0.1 and 2.0 of nominal
For example, at the reading of 4.2 kA, the worst-case error is max(0.0025  4.2 kA, 0.001  5 kA) + 0.504 kA = 0.515 kA.
EXAMPLE: VOLTAGE MONITORING
A positive-sequence voltage on a 400 kV system measured via source 2 is to be monitored by the dcmA H3 output with a
range of 0 to 1 mA. The VT secondary setting is 66.4 V, the VT ratio setting is 6024, and the VT connection setting is
“Delta”. The voltage should be monitored in the range from 70% to 110% of nominal.
5 The minimum and maximum positive-sequence voltages to be monitored are:
400 kV 400 kV
V min = 0.7  ------------------- = 161.66 kV, V max = 1.1  ------------------- = 254.03 kV (EQ 5.41)
3 3
The base unit for voltage (refer to the FlexElements section in this chapter for additional details) is:
V BASE = 0.0664 kV  6024 = 400 kV (EQ 5.42)
The minimum and maximum voltage values to be monitored (in pu) are:
161.66 kV 254.03 kV
minimum voltage = --------------------------- = 0.404 pu, maximum voltage = --------------------------- = 0.635 pu (EQ 5.43)
400 kV 400 kV
DCMA OUTPUT H3 SOURCE: “SRC 2 V_1 mag”
DCMA OUTPUT H3 RANGE: “0 to 1 mA”
DCMA OUTPUT H3 MIN VAL: “0.404 pu”
The limit settings differ from the expected 0.7 pu and 1.1 pu because the relay calculates the positive-sequence quantities
scaled to the phase-to-ground voltages, even if the VTs are connected in “Delta” (refer to the Metering conventions section
in chapter 6), while at the same time the VT nominal voltage is 1 pu for the settings. Consequently the settings required in
this example differ from naturally expected by the factor of 3 .
The worst-case error for this application could be calculated by superimposing the following two sources of error:
• ±0.5% of the full scale for the analog output module, or  0.005   1 – 0   254.03 kV =  1.27 kV
• ±0.5% of reading
For example, under nominal conditions, the positive-sequence reads 230.94 kV and the worst-case error is
0.005 x 230.94 kV + 1.27 kV = 2.42 kV.

5 SETTINGS 5.10 TESTING
5.10TESTING 5.10.1 TEST MODE
PATH: SETTINGS  TESTING  TEST MODE
 SETTINGS TEST MODE Range: Disabled, Isolated, Forcible

 TESTING FUNCTION: Disabled
TEST MODE FORCING: Range: FlexLogic operand
MESSAGE
On
The D60 provides a test facility to verify the functionality of contact inputs and outputs, some communication channels and
the phasor measurement unit (where applicable), using simulated conditions. The test mode is indicated on the relay face-
plate by a Test Mode LED indicator.
The test mode may be in any of three states: disabled, isolated, or forcible.
In the “Disabled” mode, D60 operation is normal and all test features are disabled.
In the “Isolated” mode, the D60 is prevented from performing certain control actions, including tripping via contact outputs.
All relay contact outputs, including latching outputs, are disabled. Channel tests and phasor measurement unit tests remain
usable on applicable UR-series models.
In the “Forcible” mode, the operand selected by the TEST MODE FORCING setting controls the relay inputs and outputs. If the
test mode is forcible, and the operand assigned to the TEST MODE FORCING setting is “Off”, the D60 inputs and outputs oper-
ate normally. If the test mode is forcible, and the operand assigned to the TEST MODE FORCING setting is “On”, the D60 con-
tact inputs and outputs are forced to the values specified in the following sections. Forcing may be controlled by manually
changing the operand selected by the TEST MODE FORCING setting between on and off, or by selecting a user-programma-
ble pushbutton, contact input, or communication-based input operand. Channel tests and phasor measurement unit tests
remain usable on applicable UR-series models.
5
Communications based inputs and outputs remain fully operational in test mode. If a control action is programmed
using direct inputs and outputs or remote inputs and outputs, then the test procedure must take this into account.
NOTE
When in “Forcible” mode, the operand selected by the TEST MODE FORCING setting dictates further response of the D60 to
testing conditions. To force contact inputs and outputs through relay settings, set TEST MODE FORCING to “On”. To force con-
tact inputs and outputs through a user-programmable condition, such as FlexLogic operand (pushbutton, digital input, com-
munication-based input, or a combination of these), set TEST MODE FORCING to the desired operand. The contact input or
output is forced when the selected operand assumes a logic 1 state.
The D60 remains fully operational in test mode, allowing for various testing procedures. In particular, the protection and
control elements, FlexLogic, and communication-based inputs and outputs function normally.
The only difference between the normal operation and the test mode is the behavior of the input and output contacts. The
contact inputs can be forced to report as open or closed or remain fully operational, whereas the contact outputs can be
forced to open, close, freeze, or remain fully operational. The response of the digital input and output contacts to the test
mode is programmed individually for each input and output using the force contact inputs and force contact outputs test
functions described in the following sections.
The test mode state is indicated on the relay faceplate by a combination of the Test Mode LED indicator, the In-Service LED
indicator, and by the critical fail relay, as shown in the following table.

5.10 TESTING 5 SETTINGS
Table 5–37: TEST MODE OPERATION

TEST MODE TEST MODE IN-SERVICE TEST MODE CRITICAL INPUT AND OUTPUT BEHAVIOR
FUNCTION FORCING LED LED FAIL
OPERAND RELAY
Disabled No effect Unaffected Off Unaffected Contact outputs and inputs are under normal
operation. Channel tests and PMU tests not
operational (where applicable).
Isolated No effect Off On De- Contact outputs are disabled and contact inputs
energized are operational. Channel tests and PMU tests
are also operational (where applicable).
Forcible On (logic 1) Off Flashing De- Contact inputs and outputs are controlled by the
energized force contact input and force contact output
functions. Channel tests and PMU tests are
Off (logic 0) Off Flashing De- Contact outputs and inputs are under normal
energized operation. Channel tests and PMU tests are also
The TEST MODE FUNCTION setting can only be changed by a direct user command. Following a restart, power up, settings
upload, or firmware upgrade, the test mode will remain at the last programmed value. This allows a D60 that has been
placed in isolated mode to remain isolated during testing and maintenance activities. On restart, the TEST MODE FORCING
setting and the force contact input and force contact output settings all revert to their default states.
5.10.2 FORCE CONTACT INPUTS
PATH: SETTINGS  TESTING  FORCE CONTACT INPUTS
5  FORCE CONTACT
 INPUTS
FORCE Cont Ip 1
:Disabled
Range: Disabled, Open, Closed
FORCE Cont Ip 2 Range: Disabled, Open, Closed

MESSAGE
:Disabled

FORCE Cont Ip xx Range: Disabled, Open, Closed

MESSAGE
:Disabled
The relay digital inputs (contact inputs) could be pre-programmed to respond to the test mode in the following ways:
• If set to “Disabled”, the input remains fully operational. It is controlled by the voltage across its input terminals and can
be turned on and off by external circuitry. This value should be selected if a given input must be operational during the
test. This includes, for example, an input initiating the test, or being a part of a user pre-programmed test sequence.
• If set to “Open”, the input is forced to report as opened (Logic 0) for the entire duration of the test mode regardless of
the voltage across the input terminals.
• If set to “Closed”, the input is forced to report as closed (Logic 1) for the entire duration of the test mode regardless of
the voltage across the input terminals.
The force contact inputs feature provides a method of performing checks on the function of all contact inputs. Once
enabled, the relay is placed into test mode, allowing this feature to override the normal function of contact inputs. The Test
Mode LED will be on, indicating that the relay is in test mode. The state of each contact input may be programmed as “Dis-
abled”, “Open”, or “Closed”. All contact input operations return to normal when all settings for this feature are disabled.

5.10.3 FORCE CONTACT OUTPUTS
PATH: SETTINGS  TESTING  FORCE CONTACT OUTPUTS
 FORCE CONTACT FORCE Cont Op 1 Range: Disabled, Energized, De-energized, Freeze

 OUTPUTS :Disabled
FORCE Cont Op 2 Range: Disabled, Energized, De-energized, Freeze
MESSAGE
:Disabled

FORCE Cont Op xx Range: Disabled, Energized, De-energized, Freeze

MESSAGE
:Disabled
The relay contact outputs can be pre-programmed to respond to the test mode.
If set to “Disabled”, the contact output remains fully operational. If operates when its control operand is logic 1 and will
resets when its control operand is logic 0. If set to “Energized”, the output will close and remain closed for the entire dura-
tion of the test mode, regardless of the status of the operand configured to control the output contact. If set to “De-ener-
gized”, the output will open and remain opened for the entire duration of the test mode regardless of the status of the
operand configured to control the output contact. If set to “Freeze”, the output retains its position from before entering the
test mode, regardless of the status of the operand configured to control the output contact.
These settings are applied two ways. First, external circuits may be tested by energizing or de-energizing contacts. Sec-
ond, by controlling the output contact state, relay logic may be tested and undesirable effects on external circuits avoided.
Example 1: Initiating test mode through user-programmable pushbutton 1
For example, the test mode can be initiated from user-programmable pushbutton 1. The pushbutton will be programmed as
“Latched” (pushbutton pressed to initiate the test, and pressed again to terminate the test). During the test, digital input 1
5
should remain operational, digital inputs 2 and 3 should open, and digital input 4 should close. Also, contact output 1 should
freeze, contact output 2 should open, contact output 3 should close, and contact output 4 should remain fully operational.
The required settings are shown below.
To enable user-programmable pushbutton 1 to initiate the test mode, make the following changes in the SETTINGS 
TESTING  TEST MODE menu: TEST MODE FUNCTION: “Enabled” and TEST MODE INITIATE: “PUSHBUTTON 1 ON”
Make the following changes to configure the contact inputs and outputs. In the SETTINGS  TESTING  FORCE CONTACT
INPUTS and FORCE CONTACT OUTPUTS menus, set:
FORCE Cont Ip 1: “Disabled”, FORCE Cont Ip 2: “Open”, FORCE Cont Ip 3: “Open”, and FORCE Cont Ip 4: “Closed”
FORCE Cont Op 1: “Freeze”, FORCE Cont Op 2: “De-energized”, FORCE Cont Op 3: “Energized”,
and FORCE Cont Op 4: “Disabled”
Example 2: Initiating a test from user-programmable pushbutton 1 or through remote input 1
In this example, the test can be initiated locally from user-programmable pushbutton 1 or remotely through remote input 1.
Both the pushbutton and the remote input will be programmed as “Latched”. Write the following FlexLogic equation:
Set the user-programmable pushbutton as latching by changing SETTINGS  PRODUCT SETUP  USER-PROGRAMMABLE
PUSHBUTTONS  USER PUSHBUTTON 1  PUSHBUTTON 1 FUNCTION to “Latched”. To enable either pushbutton 1 or remote
input 1 to initiate the Test mode, make the following changes in the SETTINGS  TESTING  TEST MODE menu:
TEST MODE FUNCTION: “Enabled” and TEST MODE INITIATE: “VO1”

5.10.4 PHASOR MEASUREMENT UNIT TEST VALUES
PATH: SETTINGS  TESTING  PMU TEST VALUES  PMU 1 TEST VALUES
 PMU 1 PMU 1 TEST Range: Enabled, Disabled

 TEST VALUES FUNCTION: Disabled
PMU 1 VA TEST Range: 0.00 to 700.00 kV in steps of 0.01
MESSAGE
MAGNITUDE: 500.00 kV
PMU 1 VA TEST Range: –180.00 to 180.00° in steps of 0.05
MESSAGE
ANGLE: 0.00°
PMU 1 VB TEST Range: 0.00 to 700.00 kV in steps of 0.01
MESSAGE
PMU 1 VB TEST Range: –180.00 to 180.00° in steps of 0.05
MESSAGE
ANGLE: –120.00°
PMU 1 VC TEST Range: 0.00 to 700.00 kV in steps of 0.01
MESSAGE
PMU 1 VC TEST Range: –180.00 to 180.00° in steps of 0.05
MESSAGE
ANGLE: 120.00°
PMU 1 VX TEST Range: 0.00 to 700.00 kV in steps of 0.01
MESSAGE
PMU 1 VX TEST Range: –180.00 to 180.00° in steps of 0.05
5 MESSAGE
ANGLE: 0.00°
PMU 1 IA TEST Range: 0.000 to 9.999 kA in steps of 0.001
MESSAGE
MAGNITUDE: 1.000 kA
PMU 1 IA TEST Range: –180.00 to 180.00° in steps of 0.05
MESSAGE
ANGLE: –10.00°
PMU 1 IB TEST Range: 0.000 to 9.999 kA in steps of 0.001
MESSAGE
MAGNITUDE: 1.000 kA
PMU 1 IB TEST Range: –180.00 to 180.00° in steps of 0.05
MESSAGE
ANGLE: –130.00°
PMU 1 IC TEST Range: 0.000 to 9.999 kA in steps of 0.001
MESSAGE
MAGNITUDE: 1.000 kA
PMU 1 IC TEST Range: –180.00 to 180.00° in steps of 0.05
MESSAGE
ANGLE: 110.00°
PMU 1 IG TEST Range: 0.000 to 9.999 kA in steps of 0.001
MESSAGE
MAGNITUDE: 0.000 kA
PMU 1 IG TEST Range: –180.00 to 180.00° in steps of 0.05
MESSAGE
ANGLE: 0.00°
PMU 1 TEST Range: 20.000 to 60.000 Hz in steps of 0.001
MESSAGE
FREQUENCY: 60.000 Hz
PMU 1 TEST Range: –10.000 to 10.000 Hz/s in steps of 0.001
MESSAGE
df/dt: 0.000 Hz/s
The relay must be in test mode to use the PMU test mode. That is, the TESTING  TEST MODE FUNCTION setting must be
“Enabled” and the TESTING  TEST MODE INITIATE initiating signal must be “On”.

During the PMU test mode, the physical channels (VA, VB, VC, VX, IA, IB, IC, and IG), frequency, and rate of change of fre-
quency are substituted with user values, while the symmetrical components are calculated from the physical channels. The
test values are not explicitly marked in the outgoing data frames. When required, it is recommended to use the user-pro-
grammable digital channels to signal the C37.118 client that test values are being sent in place of the real measurements.
The UR Synchrophasor Implementation defines a test mode which sends a pre-defined set of Synchrophasors out over the
communication channel when the test mode function setting is enabled. In test mode, the following actions take place:
a. The Data Invalid / Test Mode bit (bit 15 in the STAT word) is set.
b. The Sim bit in all output datasets is set.


6 ACTUAL VALUES 6.1 OVERVIEW
6 ACTUAL VALUES 6.1OVERVIEW 6.1.1 ACTUAL VALUES MENU
 ACTUAL VALUES  CONTACT INPUTS

See page 6-4.
 STATUS 
 VIRTUAL INPUTS
See page 6-4.

 REMOTE INPUTS
See page 6-4.

 REMOTE DPS INPUTS
See page 6-5.

 TELEPROTECTION
See page 6-5.
 INPUTS
 CONTACT OUTPUTS
See page 6-5.

 VIRTUAL OUTPUTS
See page 6-6.

 AUTORECLOSE
See page 6-6.

 REMOTE DEVICES
See page 6-6.
 STATUS
 REMOTE DEVICES
See page 6-7.
 STATISTICS
 DIGITAL COUNTERS
See page 6-7.

 SELECTOR SWITCHES
See page 6-7.
6

 FLEX STATES
See page 6-8.

 ETHERNET
See page 6-8.

 REAL TIME CLOCK
See page 6-8.
 SYNCHRONIZING
 DIRECT INPUTS
See page 6-9.

 DIRECT DEVICES
See page 6-10.
 STATUS
 IEC 61850
See page 6-10.
 GOOSE UINTEGERS
 TELEPROT CH TESTS
See page 6-10.

 COMM STATUS
See page 6-11.
 REMAINING CONNECT
 PRP
See page 6-11.


6.1 OVERVIEW 6 ACTUAL VALUES
 ACTUAL VALUES  SOURCE SRC 1

See page 6-16.
 METERING 
 SOURCE SRC 2

 SOURCE SRC 3

 SOURCE SRC 4

 SENSITIVE
See page 6-20.
 DIRECTIONAL POWER
 SYNCHROCHECK
See page 6-20.

 TRACKING FREQUENCY
See page 6-20.

 FREQUENCY RATE
See page 6-20.
 OF CHANGE
 FLEXELEMENTS
See page 6-21.

 IEC 61850
See page 6-21.
 GOOSE ANALOGS
 WATTMETRIC
See page 6-22.
 GROUND FAULT 1
 WATTMETRIC
See page 6-22.
6  GROUND FAULT 2
 PHASOR MEASUREMENT
See page 6-22.
 UNIT
 PMU AGGREGATOR
See page 6-23.

 TRANSDUCER I/O
See page 6-23.
 DCMA INPUTS
 TRANSDUCER I/O
See page 6-23.
 RTD INPUTS
 ACTUAL VALUES  FAULT REPORTS

See page 6-24.
 RECORDS 
 EVENT RECORDS
See page 6-24.

 OSCILLOGRAPHY
See page 6-25.

 DATA LOGGER
See page 6-25.

 PMU
See page 6-25.
 RECORDS

6 ACTUAL VALUES 6.1 OVERVIEW
 MAINTENANCE
See page 6-26.

 ACTUAL VALUES  MODEL INFORMATION

See page 6-27.
 PRODUCT INFO 
 FIRMWARE REVISIONS
See page 6-27.


6.2 STATUS 6 ACTUAL VALUES
6.2STATUS
For status reporting, ‘On’ represents Logic 1 and ‘Off’ represents Logic 0.
NOTE
6.2.1 CONTACT INPUTS
PATH: ACTUAL VALUES  STATUS  CONTACT INPUTS
 CONTACT INPUTS Cont Ip 1 Range: On, Off

 Off
Cont Ip 2 Range: On, Off
MESSAGE
Off

Cont Ip xx Range: On, Off

MESSAGE
Off
The present status of the contact inputs is shown here. The first line of a message display indicates the ID of the contact
input. For example, ‘Cont Ip 1’ refers to the contact input in terms of the default name-array index. The second line of the
display indicates the logic state of the contact input.
PATH: ACTUAL VALUES  STATUS  VIRTUAL INPUTS
 VIRTUAL INPUTS Virt Ip 1 Range: On, Off

 Off
Virt Ip 2 Range: On, Off
MESSAGE
Off
6 Virt Ip 64

Range: On, Off
MESSAGE
Off
The present status of the 64 virtual inputs is shown here. The first line of a message display indicates the ID of the virtual
input. For example, ‘Virt Ip 1’ refers to the virtual input in terms of the default name. The second line of the display indicates
the logic state of the virtual input.
6.2.3 REMOTE INPUTS
PATH: ACTUAL VALUES  STATUS  REMOTE INPUTS
 REMOTE INPUTS REMOTE INPUT 1 Range: On, Off

 STATUS: Off
REMOTE INPUT 2 Range: On, Off
MESSAGE
STATUS: Off

REMOTE INPUT 32 Range: On, Off

MESSAGE
STATUS: Off
The present state of the 32 remote inputs is shown here.

The state displayed will be that of the remote point unless the remote device has been established to be “Offline” in which
case the value shown is the programmed default state for the remote input.

6 ACTUAL VALUES 6.2 STATUS
6.2.4 REMOTE DOUBLE-POINT STATUS INPUTS
PATH: ACTUAL VALUES  STATUS  REMOTE DPS INPUTS
 REMOTE DPS INPUTS REMOTE DPS INPUT 1 Range: On, Off, Intermediate, Bad
 STATUS: Bad
REMOTE DPS INPUT 2 Range: On, Off, Intermediate, Bad
MESSAGE
STATUS: Bad

REMOTE DPS INPUT 5 Range: On, Off, Intermediate, Bad

MESSAGE
STATUS: Bad
The present state of the remote double-point status inputs is shown here. The actual values indicate if the remote double-
point status inputs are in the on (close), off (open), intermediate, or bad state.
6.2.5 TELEPROTECTION INPUTS
PATH: ACTUAL VALUES  STATUS  TELEPROTECTION INPUTS
 TELEPROTECTION TELEPROTECTION Range: Off, On

 INPUTS INPUT 1-1: Off
TELEPROTECTION Range: Off, On
MESSAGE
INPUT 1-2: Off


MESSAGE
INPUT 1-16: Off
MESSAGE
INPUT 2-1: Off
TELEPROTECTION Range: Off, On 6
MESSAGE
INPUT 2-2: Off


MESSAGE
INPUT 2-16: Off
The present state of teleprotection inputs from communication channels 1 and 2 are shown here. The state displayed will
be that of corresponding remote output unless the channel is declared failed.
6.2.6 CONTACT OUTPUTS
PATH: ACTUAL VALUES  STATUS  CONTACT OUTPUTS
 CONTACT OUTPUTS Cont Op 1 Range: On, Off, VOff, VOn, IOn, IOff
 Off
Cont Op 2 Range: On, Off, VOff, VOn, IOn, IOff
MESSAGE
Off

Cont Op xx Range: On, Off, VOff, VOn, IOn, IOff

MESSAGE
Off
The present state of the contact outputs is shown here. The first line of a message display indicates the ID of the contact
output. For example, ‘Cont Op 1’ refers to the contact output in terms of the default name-array index. The second line of
the display indicates the logic state of the contact output.

For form-A contact outputs, the state of the voltage and current detectors is displayed as Off, VOff, IOff, On, IOn,
and VOn. For form-C contact outputs, the state is displayed as Off or On.
NOTE
6.2.7 VIRTUAL OUTPUTS
PATH: ACTUAL VALUES  STATUS  VIRTUAL OUTPUTS
 VIRTUAL OUTPUTS Virt Op 1 Range: On, Off

 Off
Virt Op 2 Range: On, Off
MESSAGE
Off

Virt Op 96 Range: On, Off

MESSAGE
Off
The present state of up to 96 virtual outputs is shown here. The first line of a message display indicates the ID of the virtual
output. For example, ‘Virt Op 1’ refers to the virtual output in terms of the default name-array index. The second line of the
display indicates the logic state of the virtual output, as calculated by the FlexLogic equation for that output.
6.2.8 AUTORECLOSE
PATH: ACTUAL VALUES  STATUS  AUTORECLOSE
 AUTORECLOSE AUTORECLOSE Range: 0, 1, 2, 3, 4

 SHOT COUNT: 0
The automatic reclosure shot count is shown here.
6.2.9 REMOTE DEVICES

6 a) STATUS
PATH: ACTUAL VALUES  STATUS  REMOTE DEVICES STATUS
 REMOTE DEVICES All REMOTE DEVICES Range: Yes, No

 STATUS ONLINE: No
REMOTE DEVICE 1 Range: Online, Offline
MESSAGE
STATUS: Offline
MESSAGE
STATUS: Offline


MESSAGE
STATUS: Offline
The present state of the programmed remote devices is shown here. The ALL REMOTE DEVICES ONLINE message indicates
whether or not all programmed remote devices are online. If the corresponding state is "No", then at least one required
remote device is not online.

b) STATISTICS
PATH: ACTUAL VALUES  STATUS  REMOTE DEVICES STATISTICS  REMOTE DEVICE 1(16)
 REMOTE DEVICE 1 REMOTE DEVICE 1

 StNum: 0
REMOTE DEVICE 1
MESSAGE
SqNum: 0
Statistical data (two types) for up to 16 programmed remote devices is shown here.
The STNUM number is obtained from the indicated remote device and increments whenever a change of state of at least
one item occurs in the GSSE/GOOSE message. The SQNUM number is obtained from the indicated remote device and
increments whenever a GSSE/GOOSE message, without a state change, is sent. When the GSSE/GOOSE message
trasmits a state change, the SQNUM resets to 0. This number rolls over to zero when a count of 4,294,967,295 is incre-
mented.
6.2.10 DIGITAL COUNTERS
PATH: ACTUAL VALUES  STATUS  DIGITAL COUNTERS  DIGITAL COUNTERS Counter 1(8)
 DIGITAL COUNTERS Counter 1 ACCUM:

 Counter 1 0
Counter 1 FROZEN:
MESSAGE
0
Counter 1 FROZEN:
MESSAGE
YYYY/MM/DD HH:MM:SS
Counter 1 MICROS:
MESSAGE
0
The present status of the eight digital counters is shown here. The status of each counter, with the user-defined counter
name, includes the accumulated and frozen counts (the count units label will also appear). Also included, is the date and
time stamp for the frozen count. The COUNTER 1 MICROS value refers to the microsecond portion of the time stamp.
6
6.2.11 SELECTOR SWITCHES
PATH: ACTUAL VALUES  STATUS  SELECTOR SWITCHES
 SELECTOR SWITCHES SELECTOR SWITCH 1 Range: Current Position / 7

 POSITION: 0/7
SELECTOR SWITCH 2 Range: Current Position / 7
MESSAGE
POSITION: 0/7
The display shows both the current position and the full range. The current position only (an integer from 0 through 7) is the
actual value.

6.2.12 FLEX STATES
PATH: ACTUAL VALUES  STATUS  FLEX STATES
 FLEX STATES PARAM 1: Off Range: Off, On

 Off
PARAM 2: Off Range: Off, On
MESSAGE
Off

PARAM 256: Off Range: Off, On

MESSAGE
Off
There are 256 FlexStateTM bits available. The second line value indicates the state of the given FlexState bit.
6.2.13 ETHERNET
PATH: ACTUAL VALUES  STATUS  ETHERNET
 ETHERNET ETHERNET PRI LINK Range: Fail, OK

 STATUS: Fail
ETHERNET SEC LINK Range: Fail, OK
MESSAGE
STATUS: Fail
ETHERNET TRD LINK Range: Fail, OK
MESSAGE
STATUS: Fail
These values indicate the status of the first, second, and third Ethernet links.
6.2.14 REAL TIME CLOCK SYNCHRONIZING
6 PATH: ACTUAL VALUES  STATUS  REAL TIME CLOCK SYNCHRONIZING
 REAL TIME CLOCK RTC Sync Source: Range: See text below
 SYNCHRONIZING None
GrandMaster ID: Range: Any 8 octet value

MESSAGE
0X0000000000000000
Accuracy: Range: 0 to 999, 999, 999 ns
MESSAGE
999,999,999 ns
Port 1 PTP State: Range: Disabled, No Signal, Calibrating, Synch’d (No
MESSAGE Pdelay), Synchronized
NO SIGNAL
NO SIGNAL
NO SIGNAL
PTP - IRIG-B Delta: Range: -500,000,000 to +500,000,000 ns
MESSAGE
500,000,000 ns
The RTC Sync Source actual value is the time synchronizing source the relay is using at present. Possible sources are:
Port 1 PTP Clock, Port 2 PTP Clock, Port 3 PTP Clock, IRIG-B, SNTP, and None.
The Grandmaster ID is the grandmasterIdentity code being received from the present PTP grandmaster, if any. When the
relay is not using any PTP grandmaster, this actual value is zero. The grandmasterIdentity code is specified by PTP to be
globally unique, so one can always know which clock is grandmaster in a system with multiple grandmaster-capable clocks.

Accuracy is the estimated maximum time error at present in the RTC, considering the quality information imbedded in the
received time signal. The value 999,999,999 indicates that the magnitude of the estimated error is one second or more, or
that the error cannot be estimated.
PORT 1…3 PTP STATE is the present state of the port’s PTP clock. The PTP clock state is:
• DISABLED is the port’s function setting is Disabled,
• NO SIGNAL if enabled but no signal from an active master has been found and selected,
• CALIBRATING if an active master has been selected but lock is not at present established,
• SYNCH’D (NO PDELAY) if the port is synchronized, but the peer delay mechanism is non-operational, and
• SYNCHRONIZED if synchronized.
PTP-— IRIG-B DELTA is the time difference, measured in nanoseconds, between the fractional seconds portion of the time
being received via PTP and that being received via IRIG-B. A positive value indicates that PTP time is fast compared to
IRIG-B time.
6.2.15 DIRECT INPUTS
PATH: ACTUAL VALUES  STATUS  DIRECT INPUTS
 DIRECT INPUTS AVG MSG RETURN

 TIME CH1: 0 ms
UNRETURNED MSG
MESSAGE
COUNT CH1: 0
CRC FAIL COUNT
MESSAGE
CH1: 0
AVG MSG RETURN
MESSAGE
TIME CH2: 0 ms
UNRETURNED MSG
MESSAGE
COUNT CH2: 0
6
CRC FAIL COUNT
MESSAGE
CH2: 0
DIRECT INPUT 1:
MESSAGE
On
DIRECT INPUT 2:
MESSAGE
On

DIRECT INPUT 32:

MESSAGE
On
The AVERAGE MSG RETURN TIME is the time taken for direct output messages to return to the sender in a direct input/output
ring configuration (this value is not applicable for non-ring configurations). This is a rolling average calculated for the last
ten messages. There are two return times for dual-channel communications modules.
The UNRETURNED MSG COUNT values (one per communications channel) count the direct output messages that do not
make the trip around the communications ring. The CRC FAIL COUNT values (one per communications channel) count the
direct output messages that have been received but fail the CRC check. High values for either of these counts may indicate
on a problem with wiring, the communication channel, or one or more relays. The UNRETURNED MSG COUNT and CRC FAIL
COUNT values can be cleared using the CLEAR DIRECT I/O COUNTERS command.
The DIRECT INPUT 1 to DIRECT INPUT (32) values represent the state of each direct input.

6.2.16 DIRECT DEVICES STATUS
PATH: ACTUAL VALUES  STATUS  DIRECT DEVICES STATUS
 DIRECT DEVICES DIRECT DEVICE 1 Range: Offline, Online

 STATUS STATUS: Offline
DIRECT DEVICE 2 Range: Offline, Online
MESSAGE
STATUS: Offline

DIRECT DEVICE 16 Range: Offline, Online

MESSAGE
STATUS: Offline
These actual values represent the state of direct devices 1 through 16.
6.2.17 IEC 61850 GOOSE INTEGERS
PATH: ACTUAL VALUES  STATUS  IEC 61850 GOOSE UINTEGERS
 IEC 61850 UINT INPUT 1

 GOOSE UINTEGERS 0
UINT INPUT 2
MESSAGE
0

UINT INPUT 16
MESSAGE
0
6 ter 2 for additional details.
The IEC 61850 GGIO5 integer input data points are displayed in this menu. The GGIO5 integer data values are received
via IEC 61850 GOOSE messages sent from other devices.
6.2.18 TELEPROTECTION CHANNEL TESTS
PATH: ACTUAL VALUES  STATUS  TELEPROT CH TESTS
 TELEPROT CH TESTS CHANNEL 1 Range: n/a, FAIL, OK

 STATUS: n/a
CHANNEL 1 LOST Range: 1 to 65535 in steps of 1
MESSAGE
PACKETS: 1
CHANNEL 2 Range: n/a, FAIL, OK
MESSAGE
STATUS: n/a
CHANNEL 2 LOST Range: 1 to 65535 in steps of 1
MESSAGE
PACKETS: 1
VALIDITY OF CHANNEL Range: n/a, FAIL, OK
MESSAGE
CONFIGURATION: FAIL
The status information for two channels is shown here.

• CHANNEL 1 STATUS: This represents the receiver status of each channel. If the value is “OK”, teleprotection is
enabled and data is being received from the remote terminal; If the value is “FAIL”, teleprotection enabled and data is
not being received from the remote terminal. If “n/a”, teleprotection is disabled.
• CHANNEL 1 LOST PACKETS: Data is transmitted to the remote terminals in data packets at a rate of two packets per
cycle. The number of lost packets represents data packets lost in transmission; this count can be reset to 0 through the
COMMANDS  CLEAR RECORDS menu.
• VALIDITY OF CHANNEL CONFIGURATION: This value displays the current state of the communications channel
identification check, and hence validity. If a remote relay ID does not match the programmed ID at the local relay, the
“FAIL” message will be displayed. The “N/A” value appears if the local relay ID is set to a default value of “0”, the chan-
nel is failed, or if the teleprotection inputs/outputs are not enabled.
6.2.19 REMAINING CONNECTION STATUS
PATH: ACTUAL VALUES  STATUS  COMM STATUS REMAINING CONNECT
 COMM STATUS MMS (max 5) Range: 0 to 5

 REMAINING CONNECT 5
MODBUS TCP (max 4) Range: 0 to 4
MESSAGE
4
DNP (max 2) Range: 0 to 2
MESSAGE
2
IEC-104 (max 2) Range: 0 to 2
MESSAGE
2
PMU TCP (max 4) Range: 0 to 4
MESSAGE
4
These values specify the remaining number of TCP connections still available for each protocol. Every time a connection is
used, the remaining number of connections decrements. When released, the remaining number of connections increments.
If no connection is made over the specific protocol, the number equals the maximum number available for the specific pro-
tocol. 6
For example, the maximum number of Modbus TCP connections is 4. Once an EnerVista session is opened on a computer
connected to the UR over Ethernet, the Modbus TCP status shows 3. If the EnerVista application is closed, the Modbus
TCP status shows 4.
Note that the maximum number of PMU TCP connections matches the number of aggregators.
6.2.20 PARALLEL REDUNDANCY PROTOCOL (PRP)
The Parallel Redundancy Protocol (PRP) defines a redundancy protocol for high availability in substation automation net-
works.
PATH: ACTUAL VALUES  STATUS  PRP
 PRP Total Rx Port A: Range: 0 to 4G, blank if PRP disabled


Total Rx Port B: Range: 0 to 4G, blank if PRP disabled
MESSAGE
Total Errors: Range: 0 to 4G, blank if PRP disabled

MESSAGE
Mismatches Port A: Range: 0 to 4G, blank if PRP disabled

MESSAGE
Mismatches Port B: Range: 0 to 4G, blank if PRP disabled

MESSAGE

TOTAL RECEIVED PORT A is a counter for total messages received (either from DANPs or from SANs) on Port A.
TOTAL RECEIVED PORT B is a counter for total messages received (either from DANPs or from SANs) on Port B.
TOTAL ERRORS is a counter for total messages received with an error (bad port code, frame length too short).
MISMATCHES PORT A is a counter for total messages received with an error on Port A (PRP frame, but port received through
and LAN ID in the frame do not match).
MISMATCHES PORT B is a counter for total messages received with an error on Port B (PRP frame, but port received through
and LAN ID in the frame do not match).

6 ACTUAL VALUES 6.3 METERING
6.3METERING 6.3.1 METERING CONVENTIONS
a) UR CONVENTION FOR MEASURING POWER AND ENERGY

The following figure illustrates the conventions established for use in UR-series relays.
PER IEEE CONVENTIONS

Generator
PARAMETERS AS SEEN
G BY THE UR RELAY
Voltage +Q
VCG
WATTS = Positive IC
PF = Lead PF = Lag
VARS = Positive
PF = Lag IA
VAG -P +P
Current
IB IA
PF = Lag PF = Lead
UR RELAY
VBG -Q
M LOAD
- 1
Inductive Resistive S=VI
Generator
VCG
+Q
Voltage
PF = Lead PF = Lag
WATTS = Positive
IA
VARS = Negative IC
PF = Lead VAG -P +P
IA
Current
PF = Lag PF = Lead
IB
UR RELAY
VBG -Q
LOAD S=VI
6
- 2
Resistive
Inductive Resistive
M LOAD
VCG +Q
Voltage
PF = Lead PF = Lag
IB
IA
WATTS = Negative
VAG
VARS = Negative -P +P
PF = Lag
IA
IC PF = Lag PF = Lead
Current
VBG
-Q
UR RELAY
G S=VI
- 3
Generator
Resistive
LOAD
VCG
+Q
Voltage IB
PF = Lead PF = Lag
WATTS = Negative IA
VARS = Positive VAG -P +P
PF = Lead
IC
IA
Current
PF = Lag PF = Lead
VBG -Q
UR RELAY
G 827239AC.CDR
- 4
S=VI
Generator
Figure 6–1: FLOW DIRECTION OF SIGNED VALUES FOR WATTS AND VARS

6.3 METERING 6 ACTUAL VALUES
b) UR CONVENTION FOR MEASURING PHASE ANGLES

All phasors calculated by UR-series relays and used for protection, control and metering functions are rotating phasors that
maintain the correct phase angle relationships with each other at all times.
For display and oscillography purposes, all phasor angles in a given relay are referred to an AC input channel pre-selected
by the SETTINGS  SYSTEM SETUP  POWER SYSTEM  FREQUENCY AND PHASE REFERENCE setting. This setting
defines a particular AC signal source to be used as the reference.
The relay will first determine if any “Phase VT” bank is indicated in the source. If it is, voltage channel VA of that bank is
used as the angle reference. Otherwise, the relay determines if any “Aux VT” bank is indicated; if it is, the auxiliary voltage
channel of that bank is used as the angle reference. If neither of the two conditions is satisfied, then two more steps of this
hierarchical procedure to determine the reference signal include “Phase CT” bank and “Ground CT” bank.
If the AC signal pre-selected by the relay upon configuration is not measurable, the phase angles are not referenced. The
phase angles are assigned as positive in the leading direction, and are presented as negative in the lagging direction, to
more closely align with power system metering conventions. This is illustrated below.
-270o
-225o -315o
positive
angle
direction
-180o 0o
UR phase angle
reference
-135o -45o
6 -90o 827845A1.CDR
Figure 6–2: UR PHASE ANGLE MEASUREMENT CONVENTION
c) UR CONVENTION FOR MEASURING SYMMETRICAL COMPONENTS

The UR-series of relays calculate voltage symmetrical components for the power system phase A line-to-neutral voltage,
and symmetrical components of the currents for the power system phase A current. Owing to the above definition, phase
angle relations between the symmetrical currents and voltages stay the same irrespective of the connection of instrument
transformers. This is important for setting directional protection elements that use symmetrical voltages.
For display and oscillography purposes the phase angles of symmetrical components are referenced to a common refer-
ence as described in the previous sub-section.
WYE-CONNECTED INSTRUMENT TRANSFORMERS:
• ABC phase rotation: • ACB phase rotation:
1 1
V_0 = ---  V AG + V BG + V CG  V_0 = ---  V AG + V BG + V CG 
3 3
1 2 1 2
V_1 = ---  V AG + aV BG + a V CG  V_1 = ---  V AG + a V BG + aV CG 
3 3
1 2 1 2
V_2 = ---  V AG + a V BG + aV CG  V_2 = ---  V AG + aV BG + a V CG 
3 3
The above equations apply to currents as well.

DELTA-CONNECTED INSTRUMENT TRANSFORMERS:

• ABC phase rotation: • ACB phase rotation:
V_0 = N/A V_0 = N/A

1 – 30  1 30 2
2
V_1 = --------------------  V AB + aV BC + a V CA  V_1 = -----------------  V AB + a V BC + aV CA 
3 3 3 3
1  30 1 – 30  2
2
V_2 = -----------------  V AB + a V BC + aV CA  V_2 = --------------------  V AB + aV BC + a V CA 
3 3 3 3
The zero-sequence voltage is not measurable under the Delta connection of instrument transformers and is defaulted to
zero. The table below shows an example of symmetrical components calculations for the ABC phase rotation.
Table 6–1: SYMMETRICAL COMPONENTS CALCULATION EXAMPLE
SYSTEM VOLTAGES, SEC. V * VT RELAY INPUTS, SEC. V SYMM. COMP, SEC. V
CONN.
VAG VBG VCG VAB VBC VCA F5AC F6AC F7AC V0 V1 V2
13.9 76.2 79.7 84.9 138.3 85.4 WYE 13.9 76.2 79.7 19.5 56.5 23.3
0° –125° –250° –313° –97° –241° 0° –125° –250° –192° –7° –187°
UNKNOWN (only V1 and V2 84.9 138.3 85.4 DELTA 84.9 138.3 85.4 N/A 56.5 23.3
can be determined) 0° –144° –288° 0° –144° –288° –54° –234°
* The power system voltages are phase-referenced – for simplicity – to VAG and VAB, respectively. This, however, is a
relative matter. It is important to remember that the D60 displays are always referenced as specified under SETTINGS
 SYSTEM SETUP  POWER SYSTEM  FREQUENCY AND PHASE REFERENCE.
The example above is illustrated in the following figure.
SYSTEM VOLTAGES SYMMETRICAL

COMPONENTS
UR phase angle
6
reference
1
UR phase angle
A
reference
WYE VTs
C
B
0
2
U
re R ph
fe a
re se
nc a
e ng
le
A U
1
re R ph
fe a
re se
nc a
e ng
DELTA VTs le
C
B
2
827844A1.CDR
Figure 6–3: MEASUREMENT CONVENTION FOR SYMMETRICAL COMPONENTS

6.3.2 SOURCES
a) MAIN MENU
PATH: ACTUAL VALUES  METERING  SOURCE SRC1
 SOURCE SRC 1  PHASE CURRENT

See page 6–16.
  SRC 1
 GROUND CURRENT
 SRC 1
 PHASE VOLTAGE
 SRC 1
 AUXILIARY VOLTAGE
 SRC 1
 POWER
 SRC 1
 ENERGY
 SRC 1
 FREQUENCY
 SRC 1
This menu displays the metered values available for each source.
Metered values presented for each source depend on the phase and auxiliary VTs and phase and ground CTs assignments
for this particular source. For example, if no phase VT is assigned to this source, then any voltage, energy, and power val-
ues will be unavailable.
b) PHASE CURRENT METERING

PATH: ACTUAL VALUES  METERING  SOURCE SRC 1  PHASE CURRENT
6  PHASE CURRENT SRC 1 RMS Ia: 0.000

 SRC 1 b: 0.000 c: 0.000 A
SRC 1 RMS Ia:
MESSAGE
0.000 A
SRC 1 RMS Ib:
MESSAGE
0.000 A
SRC 1 RMS Ic:
MESSAGE
0.000 A
SRC 1 RMS In:
MESSAGE
0.000 A
SRC 1 PHASOR Ia:
MESSAGE
0.000 A 0.0°
SRC 1 PHASOR Ib:
MESSAGE
0.000 A 0.0°
SRC 1 PHASOR Ic:
MESSAGE
0.000 A 0.0°
SRC 1 PHASOR In:
MESSAGE
0.000 A 0.0°
SRC 1 ZERO SEQ I0:
MESSAGE
0.000 A 0.0°

SRC 1 POS SEQ I1:

MESSAGE
0.000 A 0.0°
SRC 1 NEG SEQ I2:
MESSAGE
0.000 A 0.0°
The metered phase current values are displayed in this menu. The "SRC 1" text will be replaced by whatever name was
programmed by the user for the associated source (see SETTINGS  SYSTEM SETUP  SIGNAL SOURCES).
c) GROUND CURRENT METERING

PATH: ACTUAL VALUES  METERING  SOURCE SRC 1  GROUND CURRENT
 GROUND CURRENT SRC 1 RMS Ig:

 SRC 1 0.000 A
SRC 1 PHASOR Ig:
MESSAGE
0.000 A 0.0°
SRC 1 PHASOR Igd:
MESSAGE
0.000 A 0.0°
The metered ground current values are displayed in this menu. The "SRC 1" text will be replaced by whatever name was
d) PHASE VOLTAGE METERING

PATH: ACTUAL VALUES  METERING  SOURCE SRC 1  PHASE VOLTAGE
 PHASE VOLTAGE SRC 1 RMS Vag:

 SRC 1 0.00 V
SRC 1 RMS Vbg:
MESSAGE
0.00 V
SRC 1 RMS Vcg:
MESSAGE
0.00 V 6
SRC 1 PHASOR Vag:
MESSAGE
0.000 V 0.0°
SRC 1 PHASOR Vbg:
MESSAGE
0.000 V 0.0°
SRC 1 PHASOR Vcg:
MESSAGE
0.000 V 0.0°
SRC 1 RMS Vab:
MESSAGE
0.00 V
SRC 1 RMS Vbc:
MESSAGE
0.00 V
SRC 1 RMS Vca:
MESSAGE
0.00 V
SRC 1 PHASOR Vab:
MESSAGE
0.000 V 0.0°
SRC 1 PHASOR Vbc:
MESSAGE
0.000 V 0.0°
SRC 1 PHASOR Vca:
MESSAGE
0.000 V 0.0°

SRC 1 ZERO SEQ V0:

MESSAGE
0.000 V 0.0°
SRC 1 POS SEQ V1:
MESSAGE
0.000 V 0.0°
SRC 1 NEG SEQ V2:
MESSAGE
0.000 V 0.0°
The metered phase voltage values are displayed in this menu. The "SRC 1" text will be replaced by whatever name was
e) AUXILIARY VOLTAGE METERING

PATH: ACTUAL VALUES  METERING  SOURCE SRC 1  AUXILIARY VOLTAGE
 AUXILIARY VOLTAGE SRC 1 RMS Vx:

 SRC 1 0.00 V
SRC 1 PHASOR Vx:
MESSAGE
0.000 V 0.0°
The metered auxiliary voltage values are displayed in this menu. The "SRC 1" text will be replaced by whatever name was
f) POWER METERING
PATH: ACTUAL VALUES  METERING  SOURCE SRC 1  POWER
 POWER SRC 1 REAL POWER

 SRC 1 3: 0.000 W
SRC 1 REAL POWER
MESSAGE
a: 0.000 W
6
SRC 1 REAL POWER
MESSAGE
b: 0.000 W
SRC 1 REAL POWER
MESSAGE
c: 0.000 W
SRC 1 REACTIVE PWR
MESSAGE
3: 0.000 var
SRC 1 REACTIVE PWR
MESSAGE
a: 0.000 var
SRC 1 REACTIVE PWR
MESSAGE
b: 0.000 var
SRC 1 REACTIVE PWR
MESSAGE
c: 0.000 var
SRC 1 APPARENT PWR
MESSAGE
3: 0.000 VA
SRC 1 APPARENT PWR
MESSAGE
a: 0.000 VA
SRC 1 APPARENT PWR
MESSAGE
b: 0.000 VA
SRC 1 APPARENT PWR
MESSAGE
c: 0.000 VA

SRC 1 POWER FACTOR

MESSAGE
3: 1.000
SRC 1 POWER FACTOR
MESSAGE
a: 1.000
SRC 1 POWER FACTOR
MESSAGE
b: 1.000
SRC 1 POWER FACTOR
MESSAGE
c: 1.000
The metered values for real, reactive, and apparent power, as well as power factor, are displayed in this menu. The "SRC
1" text will be replaced by whatever name was programmed by the user for the associated source (see SETTINGS  SYS-
TEM SETUP  SIGNAL SOURCES).
g) ENERGY METERING
PATH: ACTUAL VALUES  METERING  SOURCE SRC 1  ENERGY
 ENERGY SRC 1 POS WATTHOUR:

 SRC 1 0.000 Wh
SRC 1 NEG WATTHOUR:
MESSAGE
0.000 Wh
SRC 1 POS VARHOUR:
MESSAGE
0.000 varh
SRC 1 NEG VARHOUR:
MESSAGE
0.000 varh
The metered values for real and reactive energy are displayed in this menu. The "SRC 1" text will be replaced by whatever
name was programmed by the user for the associated source (see SETTINGS  SYSTEM SETUP  SIGNAL SOURCES).
Because energy values are accumulated, these values should be recorded and then reset immediately prior to changing
CT or VT characteristics. 6
h) FREQUENCY METERING
PATH: ACTUAL VALUES  METERING  SOURCE SRC 1  FREQUENCY
 FREQUENCY SRC 1 FREQUENCY:

 SRC 1 0.00 Hz
The metered frequency values are displayed in this menu. The "SRC 1" text will be replaced by whatever name was pro-
grammed by the user for the associated source (see SETTINGS  SYSTEM SETUP  SIGNAL SOURCES).
SOURCE FREQUENCY is measured via software-implemented zero-crossing detection of an AC signal. The signal is either a
Clarke transformation of three-phase voltages or currents, auxiliary voltage, or ground current as per source configuration
(see the SYSTEM SETUP  POWER SYSTEM settings). The signal used for frequency estimation is low-pass filtered. The
final frequency measurement is passed through a validation filter that eliminates false readings due to signal distortions and
transients.

6.3.3 SENSITIVE DIRECTIONAL POWER
PATH: ACTUAL VALUES  METERING  SENSITIVE DIRECTIONAL POWER
 SENSITIVE DIRECTIONAL POWER 1

 DIRECTIONAL POWER 3: 0.000 W
DIRECTIONAL POWER 2
MESSAGE
3: 0.000 W
The effective operating quantities of the sensitive directional power elements are displayed here. The display may be useful
to calibrate the feature by compensating the angular errors of the CTs and VTs with the use of the RCA and CALIBRATION
settings.
6.3.4 SYNCHROCHECK
PATH: ACTUAL VALUES  METERING  SYNCHROCHECK  SYNCHROCHECK 1(2)
 SYNCHROCHECK 1 SYNCHROCHECK 1 DELTA

 VOLT: 0.000 V
SYNCHROCHECK 1 DELTA
MESSAGE
PHASE: 0.0°
SYNCHROCHECK 1 DELTA
MESSAGE
FREQ: 0.00 Hz
The actual values menu for synchrocheck 2 is identical to that of synchrocheck 1. If a synchrocheck function setting is "Dis-
abled", the corresponding actual values menu item will not be displayed.
6.3.5 TRACKING FREQUENCY
PATH: ACTUAL VALUES  METERING  TRACKING FREQUENCY

6  TRACKING FREQUENCY TRACKING FREQUENCY:
 60.00 Hz
The tracking frequency is displayed here. The frequency is tracked based on the selection of the reference source with the
FREQUENCY AND PHASE REFERENCE setting in the SETTINGS  SYSTEM SETUP  POWER SYSTEM menu. Refer to the
Power System section of chapter 5 for additional details.
6.3.6 FREQUENCY RATE OF CHANGE
PATH: ACTUAL VALUES  METERING  FREQUENCY RATE OF CHANGE
 FREQUENCY RATE FREQUENCY RATE OF

 OF CHANGE CHANGE 1: 0.00 Hz/s
FREQUENCY RATE OF
MESSAGE
CHANGE 2: 0.00 Hz/s
FREQUENCY RATE OF
MESSAGE
CHANGE 3: 0.00 Hz/s
FREQUENCY RATE OF
MESSAGE
CHANGE 4: 0.00 Hz/s
The metered frequency rate of change for the frequency rate of change elements is shown here.

6.3.7 FLEXELEMENTS™
PATH: ACTUAL VALUES  METERING  FLEXELEMENTS  FLEXELEMENT 1(8)
 FLEXELEMENT 1 FLEXELEMENT 1
 OpSig: 0.000 pu
The operating signals for the FlexElements are displayed in pu values using the following definitions of the base units.
Table 6–2: FLEXELEMENT BASE UNITS

RTDs BASE = 100°C
(Max Delta Volts)
6.3.8 IEC 61580 GOOSE ANALOG VALUES
PATH: ACTUAL VALUES  METERING  IEC 61850 GOOSE ANALOGS

6
 IEC 61850 ANALOG INPUT 1
 GOOSE ANALOGS 0.000
ANALOG INPUT 2
MESSAGE
0.000
ANALOG INPUT 3
MESSAGE
0.000

ANALOG INPUT 32
MESSAGE
0.000
ter 2 for additional details.
The IEC 61850 GGIO3 analog input data points are displayed in this menu. The GGIO3 analog data values are received
via IEC 61850 GOOSE messages sent from other devices.

6.3.9 WATTMETRIC GROUND FAULT
PATH: ACTUAL VALUES  METERING  WATTMETRIC GROUND FAULT 1(2)
 WATTMETRIC WATT GND FLT 1:

 GROUND FAULT 1 0.000 W
This menu displays the wattmetric zero-sequence directional element operating power values.
6.3.10 PHASOR MEASUREMENT UNIT
PATH: ACTUAL VALUES  METERING  PHASOR MEASUREMENT UNIT  PMU 1(4)
 PMU 1 PMU 1 VA: Range: Va or Vab per VT bank connection

 0.0000 kV, 0.00°
PMU 1 VB: Range: Va or Vab per VT bank connection
MESSAGE
0.0000 kV, 0.00°
PMU 1 VC: Range: Va or Vab per VT bank connection
MESSAGE
0.0000 kV, 0.00°
PMU 1 VX:
MESSAGE
0.0000 kV, 0.00°
PMU 1 V1:
MESSAGE
0.0000 kV, 0.00°
PMU 1 V2:
MESSAGE
0.0000 kV, 0.00°
PMU 1 V0: Range: Substituted with zero if delta-connected VTs.
MESSAGE
0.0000 kV, 0.00°
PMU 1 IA:
6 MESSAGE
0.0000 kA, 0.00°
PMU 1 IB:
MESSAGE
0.0000 kA, 0.00°
PMU 1 IC:
MESSAGE
0.0000 kA, 0.00°
PMU 1 IG:
MESSAGE
0.0000 kA, 0.00°
PMU 1 I1:
MESSAGE
0.0000 kA, 0.00°
PMU 1 I2:
MESSAGE
0.0000 kA, 0.00°
PMU 1 I0:
MESSAGE
0.0000 kA, 0.00°
PMU 1 FREQUENCY:
MESSAGE
0.0000 Hz
PMU 1 df/dt:
MESSAGE
0.0000 Hz/s
PMU 1 CONFIG CHANGE Range: 0 to 65535
MESSAGE
COUNTER: 0

The above actual values are displayed without the corresponding time stamp as they become available per the recording
rate setting. Also, the recording post-filtering setting is applied to these values.
6.3.11 PMU AGGREGATOR
PATH: ACTUAL VALUES  METERING  PHASOR MEASUREMENT UNIT  PMU AGGREGATOR 1
 PMU AGGREGATOR 1 PMU AGGREGATOR 1

 PDU SIZE: 0
Actual values for the IEC 61850-90-5 PDU size are provided. These values allow you to know the approximate Ethernet
frame size for the data streams from each aggregator. This can help to estimate network loading. The PDU size shown in
the displays does not include the Ethernet, UDP, or IP layers. PDU sizes approaching approximately 1500 bytes result in
fragmented data frames, causing increased network traffic.
6.3.12 TRANSDUCER INPUTS AND OUTPUTS
PATH: ACTUAL VALUES  METERING  TRANSDUCER I/O DCMA INPUTS  DCMA INPUT xx
 DCMA INPUT xx DCMA INPUT xx

 0.000 mA
Actual values for each dcmA input channel that is enabled are displayed with the top line as the programmed channel ID
and the bottom line as the value followed by the programmed units.
PATH: ACTUAL VALUES  METERING  TRANSDUCER I/O RTD INPUTS  RTD INPUT xx
 RTD INPUT xx RTD INPUT xx

 -50 °C
Actual values for each RTD input channel that is enabled are displayed with the top line as the programmed channel ID and
the bottom line as the value.

6.4 RECORDS 6 ACTUAL VALUES
6.4RECORDS 6.4.1 FAULT REPORTS
PATH: ACTUAL VALUES  RECORDS  FAULT REPORTS  FAULT REPORT 1(15)
NO FAULTS TO REPORT
or
 FAULT REPORT 1 FAULT 1 Range: SRC 1, SRC 2, SRC 3, SRC 4
 LINE ID: SRC 1
FAULT 1 DATE: Range: YYYY/MM/DD
MESSAGE
2000/08/11
FAULT 1 TIME: Range: HH:MM:SS.ssssss
MESSAGE
00:00:00.000000
FAULT 1 TYPE: Range: not available if the source VTs are in the “Delta”
MESSAGE configuration
ABG
FAULT 1 LOCATION Range: not available if the source VTs are in the “Delta”
MESSAGE configuration
00.0 km
FAULT 1 RECLOSE Range: where applicable
MESSAGE
SHOT: 0
The latest 15 fault reports can be stored. The most recent fault location calculation (when applicable) is displayed in this
menu, along with the date and time stamp of the event which triggered the calculation. See the SETTINGS  PRODUCT
SETUP  FAULT REPORTS menu for assigning the source and trigger for fault calculations. Refer to the COMMANDS 
CLEAR RECORDS menu for manual clearing of the fault reports and to the SETTINGS  PRODUCT SETUP  CLEAR RELAY
RECORDS menu for automated clearing of the fault reports.
6.4.2 EVENT RECORDS
6 PATH: ACTUAL VALUES  RECORDS  EVENT RECORDS
 EVENT RECORDS EVENT: XXXX

 RESET OP(PUSHBUTTON)

EVENT: 3 EVENT 3
MESSAGE
POWER ON DATE: 2000/07/14
EVENT: 2 EVENT 3
MESSAGE
POWER OFF TIME: 14:53:00.03405
EVENT: 1
MESSAGE Date and Time Stamps
EVENTS CLEARED
The event records menu shows the contextual data associated with up to the last 1024 events, listed in chronological order
from most recent to oldest. If all 1024 event records have been filled, the oldest record will be removed as a new record is
added. Each event record shows the event identifier/sequence number, cause, and date/time stamp associated with the
event trigger. Refer to the COMMANDS  CLEAR RECORDS menu for clearing event records.

6 ACTUAL VALUES 6.4 RECORDS
6.4.3 OSCILLOGRAPHY
PATH: ACTUAL VALUES  RECORDS  OSCILLOGRAPHY
 OSCILLOGRAPHY FORCE TRIGGER? Range: No, Yes

 No
NUMBER OF TRIGGERS:
MESSAGE
0
AVAILABLE RECORDS:
MESSAGE
0
CYCLES PER RECORD:
MESSAGE
0.0
LAST CLEARED DATE:
MESSAGE
2000/07/14 15:40:16
This menu allows the user to view the number of triggers involved and number of oscillography traces available. The
CYCLES PER RECORD value is calculated to account for the fixed amount of data storage for oscillography. See the Oscillog-
raphy section of chapter 5 for additional details.
A trigger can be forced here at any time by setting “Yes” to the FORCE TRIGGER? command. Refer to the COMMANDS 
CLEAR RECORDS menu for information on clearing the oscillography records.
6.4.4 DATA LOGGER
PATH: ACTUAL VALUES  RECORDS  DATA LOGGER
 DATA LOGGER OLDEST SAMPLE TIME:

 2000/01/14 13:45:51
NEWEST SAMPLE TIME:
MESSAGE
2000/01/14 15:21:19
6
The OLDEST SAMPLE TIME represents the time at which the oldest available samples were taken. It will be static until the log
gets full, at which time it will start counting at the defined sampling rate. The NEWEST SAMPLE TIME represents the time the
most recent samples were taken. It counts up at the defined sampling rate. If the data logger channels are defined, then
both values are static.
Refer to the COMMANDS  CLEAR RECORDS menu for clearing data logger records.
6.4.5 PHASOR MEASUREMENT UNIT RECORDS
PATH: ACTUAL VALUES  RECORDS  PMU RECORDS
 PMU NUMBER OF TRIGGERS: Range: 0 to 65535 in steps of 1

 RECORDS 0
 PMU 1
MESSAGE See below.
 RECORDING
The number of triggers applicable to the phasor measurement unit recorder is indicated by the NUMBER OF TRIGGERS value.
The status of the phasor measurement unit recorder is indicated as follows:

6.4 RECORDS 6 ACTUAL VALUES
PATH: ACTUAL VALUES  RECORDS  PMU RECORDS  PMU 1 RECORDING
 PMU 1 PMU 1 FORCE TRIGGER: Range: No, Yes

 RECORDING Yes
PUM 1 AVAILABLE Range: 0 to 65535 in steps of 1
MESSAGE
RECORDS: 0
PUM 1 SECONDS Range: 0 to 6553.5 in steps of 0.1
MESSAGE
PER RECORD: 0.0
PUM 1 LAST CLEARED: Range: date and time in format shown
MESSAGE
2005/07/14 015:40:16
6.4.6 BREAKER MAINTENANCE
PATH: ACTUAL VALUES  RECORDS  MAINTENANCE  BREAKER 1(4)
 BREAKER 1 BKR 1 ARCING AMP A:

 0.00 kA2-cyc
BKR 1 ARCING AMP B:
MESSAGE
0.00 kA2-cyc
BKR 1 ARCING AMP C:
MESSAGE
0.00 kA2-cyc
BKR 1 OPERATING TIME
MESSAGE
A: 0 ms
MESSAGE
B: 0 ms
MESSAGE
C: 0 ms
6 MESSAGE
BKR 1 OPERATING
TIME: 0 ms
There is an identical menu for each of the breakers. The BKR 1 ARCING AMP values are in units of kA2-cycles. Refer to the
COMMANDS  CLEAR RECORDS menu for clearing breaker arcing current records. The BREAKER OPERATING TIME is
defined as the slowest operating time of breaker poles that were initiated to open.

6 ACTUAL VALUES 6.5 PRODUCT INFORMATION
6.5PRODUCT INFORMATION 6.5.1 MODEL INFORMATION
PATH: ACTUAL VALUES  PRODUCT INFO  MODEL INFORMATION
 MODEL INFORMATION ORDER CODE LINE 1: Range: standard GE Multilin order code format;
 D60-E00-HCL-F8F-H6H example order code shown
ORDER CODE LINE 2: Range: standard GE Multilin order code format

MESSAGE

MESSAGE

MESSAGE
SERIAL NUMBER: Range: standard GE Multilin serial number format

MESSAGE
ETHERNET MAC ADDRESS Range: standard Ethernet MAC address format

MESSAGE
000000000000
MANUFACTURING DATE: Range: YYYY/MM/DD HH:MM:SS
MESSAGE
0
PMU FEATURE ACTIVE: Range: Yes, No
MESSAGE
No
CT/ VT ADVANCED DIAG Range: Yes, No
MESSAGE
ACTIVE: No
OPERATING TIME: Range: operating time in HH:MM:SS
MESSAGE
0:00:00
LAST SETTING CHANGE: Range: YYYY/MM/DD HH:MM:SS
MESSAGE
1970/01/01 23:11:19
6
The order code, serial number, Ethernet MAC address, date and time of manufacture, and operating time are shown here.
6.5.2 FIRMWARE REVISIONS
PATH: ACTUAL VALUES  PRODUCT INFO  FIRMWARE REVISIONS
 FIRMWARE REVISIONS D60 Line Relay Range: 0.00 to 655.35

 REVISION: 7.1x Revision number of the application firmware.
MODIFICATION FILE Range: 0 to 65535 (ID of the MOD FILE)

MESSAGE Value is 0 for each standard firmware release.
NUMBER: 0
BOOT PROGRAM Range: 0.00 to 655.35
MESSAGE Revision number of the boot program firmware.
REVISION: 3.01
FRONT PANEL PROGRAM Range: 0.00 to 655.35
MESSAGE Revision number of faceplate program firmware.
REVISION: 0.08
COMPILE DATE: Range: Any valid date and time.
MESSAGE Date and time when product firmware was built.
2004/09/15 04:55:16
BOOT DATE: Range: Any valid date and time.
MESSAGE Date and time when the boot program was built.
2004/09/15 16:41:32
The shown data is illustrative only. A modification file number of 0 indicates that, currently, no modifications have been
installed.

6.5 PRODUCT INFORMATION 6 ACTUAL VALUES

7 COMMANDS AND TARGETS 7.1 COMMANDS
7 COMMANDS AND TARGETS 7.1COMMANDS 7.1.1 COMMANDS MENU
COMMANDS

 COMMANDS
MESSAGE
 VIRTUAL INPUTS
 COMMANDS
MESSAGE
 CLEAR RECORDS
 COMMANDS
MESSAGE
 SET DATE AND TIME
 COMMANDS
MESSAGE
 RELAY MAINTENANCE
 COMMANDS
MESSAGE
 PMU ONE-SHOT
 COMMANDS
MESSAGE
 SECURITY
The commands menu contains relay directives intended for operations personnel. All commands can be protected from
unauthorized access via the command password; see the Security section of chapter 5 for details. The following flash mes-
sage appears after successfully command entry:
COMMAND
EXECUTED
PATH: COMMANDS  VIRTUAL INPUTS
 COMMANDS Virt Ip 1 Range: Off, On

 VIRTUAL INPUTS Off
Virt Ip 2 Range: Off, On
7
Off

Virt Ip 64 Range: Off, On

MESSAGE
Off
The states of up to 64 virtual inputs are changed here. The first line of the display indicates the ID of the virtual input. The
second line indicates the current or selected status of the virtual input. This status will be a state off (logic 0) or on (logic 1).

7.1 COMMANDS 7 COMMANDS AND TARGETS
7.1.3 CLEAR RECORDS
PATH: COMMANDS  CLEAR RECORDS
 COMMANDS CLEAR FAULT REPORTS? Range: No, Yes

 CLEAR RECORDS No
CLEAR EVENT RECORDS? Range: No, Yes
No
CLEAR OSCILLOGRAPHY? Range: No, Yes
No
CLEAR DATA LOGGER? Range: No, Yes
No
CLEAR BREAKER 1 Range: No, Yes
ARCING AMPS? No
CLEAR BREAKER 2 Range: No, Yes
ARCING AMPS? No
CLEAR UNAUTHORIZED Range: No, Yes
ACCESS? No
CLEAR DIRECT I/O Range: No, Yes. Valid only for units with Direct Input/
COUNTERS? No Output module.
CLEAR PMU 1 RECORDS? Range: No, Yes

No
CLEAR PMU 1 CONFIG Range: No, Yes
CHANGE COUNTER? No
CLEAR TELEPROTECT Range: No, Yes
COUNTERS? No
CLEAR ALL RELAY Range: No, Yes
RECORDS? No
This menu contains commands for clearing historical data such as the event records. Data is cleared by changing a com-
mand setting to “Yes” and pressing the ENTER key. After clearing data, the command setting automatically reverts to “No”.
7 7.1.4 SET DATE AND TIME
PATH: COMMANDS  SET DATE AND TIME
 COMMANDS SET DATE AND TIME: (YYYY/MM/DD HH:MM:SS)

 SET DATE AND TIME 2000/01/14 13:47:03
The date and time can be entered here via the faceplate keypad, but if the relay is synchronizing to an external time source
such as PTP, IRIGB or SNTP, the manually entered time will be quickly over-written. The time setting is based on the 24-
hour clock. The complete date, as a minimum, must be entered to allow execution of this command. The new time (if
entered) and date will take effect at the moment the ENTER key is clicked.
The timescale of the entered time should be local time, including daylight time where and when applicable.

7.1.5 RELAY MAINTENANCE
PATH: COMMANDS  RELAY MAINTENANCE
 COMMANDS PERFORM LAMPTEST? Range: No, Yes

 RELAY MAINTENANCE No
UPDATE ORDER CODE? Range: No, Yes
No
REBOOT RELAY? Range: No, Yes
No
SERVICE COMMAND: Range: 0, 101
0
This menu contains commands for relay maintenance purposes. Commands for the lamp test and order code are activated
by changing a command setting to “Yes” and pressing the ENTER key. The command setting will then automatically revert
to “No”. The service command is activated by entering a numerical code and pressing the ENTER key.
The PERFORM LAMPTEST command turns on all faceplate LEDs and display pixels for a short duration. The UPDATE
ORDER CODE command causes the relay to scan the backplane for the hardware modules and update the order code to
match. If an update occurs, the following message is shown.
UPDATING...
PLEASE WAIT
There is no impact if there have been no changes to the hardware modules. When an update does not occur, the ORDER
CODE NOT UPDATED message will be shown.
The SERVICE COMMAND is used to perform specific D60 service actions. Presently, there is only one service action avail-
able. Code “101” is used to clear factory diagnostic information stored in the non-volatile memory. If a code other than “101”
is entered, the command will be ignored and no actions will be taken. Various self-checking diagnostics are performed in
the background while the D60 is running, and diagnostic information is stored on the non-volatile memory from time to time
based on the self-checking result. Although the diagnostic information is cleared before the D60 is shipped from the factory,
the user may want to clear the diagnostic information for themselves under certain circumstances. For example, it may be
desirable to clear diagnostic information after replacement of hardware. Once the diagnostic information is cleared, all self-
checking variables are reset to their initial state and diagnostics will restart from scratch.
The REBOOT RELAY COMMAND reboots the relay so that changes to configuration settings can take effect. In most cases, if
changes are made to the configuration settings these changes do not take effect unless the relay is rebooted.
With the CyberSentry option, the Administrator or Operator role can initiate the Reboot Relay command. 7
NOTE 7.1.6 PHASOR MEASUREMENT UNIT ONE-SHOT
PATH: COMMANDS  PMU ONE-SHOT
 COMMANDS PMU ONE-SHOT Range: Enabled, Disabled

 PMU ONE-SHOT FUNCTION: Disabled
PMU ONE-SHOT Range: 0 to nominal frequency – 1 in steps of 1
SEQUENCE NUMBER: 0
PMU ONE-SHOT TIME: Range: 24h time format
2005/06/14 7:58:35
This feature allows pre-scheduling a PMU measurement at a specific point in time. This functionality can be used to test for
accuracy of the PMU, and for manual collection of synchronized measurements through the system, as explained below.
When enabled, the function continuously compares the present time with the pre-set PMU ONE-SHOT TIME. When the two
times match, the function compares the present sequence number of the measured synchrophasors with the pre-set PMU
ONE-SHOT SEQUENCE NUMBER. When the two numbers match, the function freezes the synchrophasor actual values and
the corresponding protocol data items for 30 seconds. This allows manual read-out of the synchrophasor values for the

7.1 COMMANDS 7 COMMANDS AND TARGETS
pre-set time and pre-set sequence number (via the faceplate display, supported communication protocols such as Modbus
or DNP, and the EnerVista UR Setup software).
When freezing the actual values the function also asserts a PMU ONE-SHOT OP FlexLogic operand. This operand may be
configured to drive an output contact and trigger an external measuring device such as a digital scope with the intent to ver-
ify the accuracy of the PMU under test.
With reference to the figure below, the PMU one-shot function (when enabled) controls three FlexLogic operands:
• The PMU ONE-SHOT EXPIRED operand indicates that the one-shot operation has been executed, and the present time
is at least 30 seconds past the scheduled one-shot time.
• The PMU ONE-SHOT PENDING operand indicates that the one-shot operation is pending; that is, the present time is
before the scheduled one-shot time.
• The PMU ONE-SHOT OP operand indicates the one-shot operation and remains asserted for 30 seconds afterwards.
When the function is disabled, all three operands are de-asserted. The one-shot function applies to all logical PMUs of a
given D60 relay.
Figure 7–1: PMU ONE-SHOT FLEXLOGIC OPERANDS

TESTING ACCURACY OF THE PMU:
The one-shot feature can be used to test accuracy of the synchrophasor measurement. GPS-synchronized tests sets per-
form a similar function to PMUs: instead of measuring the phasor from physical signals with respect to the externally pro-
vided time reference, they produce the physical signals with respect to the externally provided time reference, given the
desired phasor values. Therefore the GPS-synchronized test sets cannot be automatically assumed more accurate than
the PMUs under test. This calls for a method to verify both the measuring device (PMU) and the source of signal (test set).
With reference to the figure below, the one-shot feature could be configured to trigger a high-accuracy scope to capture
7 both the time reference signal (rising edge of the 1 pps signal of the IRIG-B time reference), and the measured waveform.
The high-accuracy high-sampling rate record of the two signals captured by the scope can be processed using digital tools
to verify the magnitude and phase angle with respect to the time reference signal. As both the time reference and the mea-
sured signals are raw inputs to the PMU under test, their independently captured record, processed using third-party soft-
ware, is a good reference point for accuracy calculations. Such a record proves useful when discussing the test results, and
should be retained as a part of the testing documentation.
Note that the PMU under such test does not have to be connected to a real GPS receiver as the accuracy is measured with
respect to the timing reference provided to the PMU and not to the absolute UTC time. Therefore a simple IRIG-B genera-
tor could be used instead. Also, the test set does not have to support GPS synchronization. Any stable signal source can

be used. If both the PMU under test and the test set use the timing reference, they should be driven from the same IRIG-B
signal: either the same GPS receiver or IRIG-B generator. Otherwise, the setpoints of the test set and the PMU measure-
ments should not be compared as they are referenced to different time scales.
Figure 7–2: USING THE PMU ONE-SHOT FEATURE TO TEST SYNCHROPHASOR MEASUREMENT ACCURACY
COLLECTING SYNCHRONIZED MEASUREMENTS AD HOC:
The one-shot feature can be used for ad hoc collection of synchronized measurements in the network. Two or more PMU
can be pre-scheduled to freeze their measurements at the same time. When frozen the measurements could be collected
using EnerVista UR Setup or a protocol client.
7.1.7 SECURITY
iPATH: COMMANDS  SECURITY

 SECURITY ADMINISTRATOR Range: Yes, No
 LOGOFF: No Default: No
ENGINEER Range: Yes, No

LOGOFF: No Default: No
OPERATOR Range: Yes, No

LOGOFF: No Default: No
CLEAR SECURITY DATA: Range: Yes, No

Default: No
7
With the CyberSentry option, this setting is available to enable or disable the following commands:
• Administrator Logoff: Selecting ‘Yes’ allows the Supervisor to forcefully logoff an administrator session.
• Engineer Logoff: Selecting ‘Yes’ allows the Supervisor to forcefully logoff an engineer session.
• Operator Logoff: Selecting ‘Yes’ allows the Supervisor to forcefully logoff an operator session.
• Clear Security Data: Selecting ‘Yes’ allows the Supervisor to forcefully clear all the security logs and clears all the
operands associated with the self-tests.

7.2 TARGETS 7 COMMANDS AND TARGETS
7.2TARGETS 7.2.1 TARGETS MENU
TARGETS

DIGITAL ELEMENT 1: Displayed only if targets for this element are active.
MESSAGE Example shown.
LATCHED
DIGITAL ELEMENT 48: Displayed only if targets for this element are active.
MESSAGE Example shown.
LATCHED
MESSAGE


The status of any active targets will be displayed in the targets menu. If no targets are active, the display will read NO
ACTIVE TARGETS:
7.2.2 TARGET MESSAGES
When there are no active targets, the first target to become active will cause the display to immediately default to that mes-
sage. If there are active targets and the user is navigating through other messages, and when the default message timer
times out (i.e. the keypad has not been used for a determined period of time), the display will again default back to the tar-
get message.
The range of variables for the target messages is described below. Phase information will be included if applicable. If a tar-
get message status changes, the status with the highest priority will be displayed.
Table 7–1: TARGET MESSAGE PRIORITY STATUS

PRIORITY ACTIVE STATUS DESCRIPTION
1 OP element operated and still picked up
2 PKP element picked up and timed out
3 LATCHED element had operated but has dropped out
If a self test error is detected, a message appears indicating the cause of the error. For example UNIT NOT PROGRAMMED
indicates that the minimal relay settings have not been programmed.
7
7.2.3 RELAY SELF-TESTS
a) DESCRIPTION
The relay performs a number of self-test diagnostic checks to ensure device integrity. The two types of self-tests (major and
minor) are listed in the tables below. When either type of self-test error occurs, the Trouble LED Indicator will turn on and a
target message displayed. All errors record an event in the event recorder. Latched errors can be cleared by pressing the
RESET key, providing the condition is no longer present.
Major self-test errors also result in the following:
• The critical fail relay on the power supply module is de-energized.
• All other output relays are de-energized and are prevented from further operation.
• The faceplate In Service LED indicator is turned off.
• A RELAY OUT OF SERVICE event is recorded.

7 COMMANDS AND TARGETS 7.2 TARGETS
b) MAJOR SELF-TEST ERROR MESSAGES

The major self-test errors are outlined in this section.
MODULE FAILURE___:
Contact Factory (xxx)
• Latched target message: Yes.
• Description of problem: Module hardware failure detected.
• How often the test is performed: Module dependent.
• What to do: Contact the factory and supply the failure code noted in the display. The “xxx” text identifies the failed mod-
ule (for example, F8L).
INCOMPATIBLE H/W:
Contact Factory (xxx)
• Description of problem: One or more installed hardware modules is not compatible with the D60 order code.
• How often the test is performed: Module dependent.
• What to do: Contact the factory and supply the failure code noted in the display. The “xxx” text identifies the failed mod-
ule (for example, F8L).
EQUIPMENT MISMATCH:
with 2nd line detail
• Latched target message: No.
• Description of problem: The configuration of modules does not match the order code stored in the D60.
• How often the test is performed: On power up. Afterwards, the backplane is checked for missing cards every five sec-
onds.
• What to do: Check all modules against the order code, ensure they are inserted properly, and cycle control power. If
the problem persists, contact the factory.
FLEXLOGIC ERROR:
with 2nd line detail
• Latched target message: No. 7
• Description of problem: A FlexLogic equation is incorrect.
• How often the test is performed: The test is event driven, performed whenever FlexLogic equations are modified.
• What to do: Finish all equation editing and use self tests to debug any errors.
UNIT NOT PROGRAMMED:

Check Settings
• Description of problem: The PRODUCT SETUP  INSTALLATION  RELAY SETTINGS setting indicates the D60 is not pro-
grammed.
• How often the test is performed: On power up and whenever the PRODUCT SETUP  INSTALLATION  RELAY SETTINGS
setting is altered.
• What to do: Program all settings and then set PRODUCT SETUP  INSTALLATION  RELAY SETTINGS to “Programmed”.

c) MINOR SELF-TEST ERROR MESSAGES

Most of the minor self-test errors can be disabled. Refer to the settings in the User-programmable self-tests section in the
Settings chapter for additional details.
IEC 61850 DATA SET:

LLN0 GOOSE# Error
• Description of problem: A data item in a configurable GOOSE data set is not supported by the D60 order code.
• How often the test is performed: On power up.
• What to do: Verify that all the items in the GOOSE data set are supported by the D60. The EnerVista UR Setup soft-
ware will list the valid items. An IEC61850 client will also show which nodes are available for the D60.
IEC 61850 DATA SET:

LLN0 BR# Error
• Description of problem: A data item in a configurable report data set is not supported by the D60 order code.
• How often the test is performed: On power up.
• What to do: Verify that all the items in the configurable report data set are supported by the D60. The EnerVista UR
Setup software will list the valid items. An IEC61850 client will also show which nodes are available for the D60.
MAINTENANCE ALERT:
Replace Battery
• Description of problem: The battery is not functioning.
• How often the test is performed: The battery is monitored every five seconds. The error message displays after 60 sec-
onds if the problem persists.
• What to do: Replace the battery as outlined in the Maintenance chapter.
MAINTENANCE ALERT:
7 Direct I/O Ring Break
• Description of problem: Direct input and output settings are configured for a ring, but the connection is not in a ring.
• How often the test is performed: Every second.
• What to do: Check direct input and output configuration and wiring.
MAINTENANCE ALERT:
ENET PORT # OFFLINE
• Description of problem: The Ethernet connection has failed for the specified port.
• How often the test is performed: Every five seconds.
• What to do: Check the Ethernet port connection on the switch.
MAINTENANCE ALERT:
**Bad IRIG-B Signal**


• Description of problem: A bad IRIG-B input signal has been detected.
• How often the test is performed: Monitored whenever an IRIG-B signal is received.
• What to do: Ensure the following:
– The IRIG-B cable is properly connected.
– Proper cable functionality (that is, check for physical damage or perform a continuity test).
– The IRIG-B receiver is functioning.
– Check the input signal level (it may be less than specification).
If none of these apply, then contact the factory.
MAINTENANCE ALERT:
**Bad PTP Signal**

• Description of problem: No PTP enabled port has good PTP signal input.
• How often the test is performed: Activated when no acceptable signal is being received.
• What to do: Ensure the following:
– The Ethernet cable(s) are properly connected.
– At least one PTP grandmaster-capable clock is functioning.
– If strict PP is enabled, that entire network is PP compliant.
– The network is delivering PTP messages to the relay.
MAINTENANCE ALERT:
Port ## Failure

• Description of problem: An Ethernet connection has failed.
• How often the test is performed: Monitored every five seconds.
• What to do: Check Ethernet connections. Port 1 is the primary port and port 2 is the secondary port.
7
MAINTENANCE ALERT:
SNTP Failure

• Description of problem: The SNTP server is not responding.
• How often the test is performed: Every 10 to 60 seconds.
• What to do: Check SNTP configuration and network connections.
MAINTENANCE ALERT:
4L Discrepancy
• Description of problem: A discrepancy has been detected between the actual and desired state of a latching contact
output of an installed type “4L” module.
• How often the test is performed: Upon initiation of a contact output state change.
• What to do: Verify the state of the output contact and contact the factory if the problem persists.

MAINTENANCE ALERT:
GGIO Ind xxx oscill

• Description of problem: A data item in a configurable GOOSE data set is oscillating.
• How often the test is performed: Upon scanning of each configurable GOOSE data set.
• What to do: The “xxx” text denotes the data item that has been detected as oscillating. Evaluate all logic pertaining to
this item.
DIRECT I/O FAILURE:

COMM Path Incomplete

• Description of problem: A direct device is configured but not connected.
• How often the test is performed: Every second.
• What to do: Check direct input and output configuration and wiring.
REMOTE DEVICE FAIL:

COMM Path Incomplete

• Description of problem: One or more GOOSE devices are not responding.
• How often the test is performed: Event driven. The test is performed when a device programmed to receive GOOSE
messages stops receiving. This can be from 1 to 60 seconds, depending on GOOSE packets.
• What to do: Check GOOSE setup.
TEMP MONITOR:
OVER TEMPERATURE
• Description of problem: The ambient temperature is greater than the maximum operating temperature (+80°C).
7 •
•
How often the test is performed: Every hour.
What to do: Remove the D60 from service and install in a location that meets operating temperature standards.
UNEXPECTED RESTART:
Press “RESET” key
• Description of problem: Abnormal restart from modules being removed or inserted while the D60 is powered-up, when
there is an abnormal DC supply, or as a result of internal relay failure.
• How often the test is performed: Event driven.
• What to do: Contact the factory.
FIRST ETHERNET FAIL
SECOND ETHERNET FAIL

THIRD ETHERNET FAIL

• Description of problem: A link loss detection on an Ethernet port. The link loss is due to unplugging the cable or the
switch port being down.
• How often the test is performed:
• What to do: Check the connection.
d) WRONG TRANSCEIVER MESSAGES

Description: The type of SFP does not match the CPU type.
T-type CPU = All ports support fiber SFPs only
Type: minor
Target: latched
Message: "WRONG TRANSCEIVER"
A webpage "SFP Transceiver Information" is provided. This page displays the type of the SFP in it. This data is to be used
with the CPU type to know the cause of the problem.
e) SFP X MODULE FAIL MESSAGES

Description: A faulty SFP or unplugging the SFP would generate this self test.
Type: minor
Target: self reset
Message: SFP MODULE x FAIL
The webpage "SFP Transceiver Information" described in the previous section applies for this self test as well. The "SFP
Module Fail" has higher priority and it suppresses the "Ethernet Fail" target message. The "SFP MODULE FAIL FUNC-
TION" setting enables/disables this self test. The target for this self test is priority-based, with the third one being the high-
est priority. For example, if all three SFP modules fail, then the third SFP target is activated. If the third SFP module failure
resolves, then the second SFP target is activated.
HARDFIBER SELF-TEST ERROR MESSAGES
In addition to those provided by the standard UR-series devices, the UR devices implement HardFiber self-tests. These are
listed below. Any abnormal diagnostic condition indicated by the LEDs or the critical failure relay also results in a self-test 7
message, so troubleshooting is described here. For other relays, such at the B95Plus, see that product’s instruction manual.
Equipment Mismatch Major Self-Test
Description: The number or type of installed hardware modules does not match the order code stored in the CPU. The stan-
dard UR-series Equipment Mismatch self-test is extended to cover the possible presence of a Process Card.
Severity: Protection is not available and all contact outputs and shared outputs are de-asserted.
If this message appears, check all modules against the order code. Ensure they are inserted properly, and cycle the control
power. If a module has intentionally been added or removed use the Update Order Code command to notify the relay that
the current module configuration is correct.
Module Failure Major Self-Test
Description: UR-series device module hardware failure detected.
If this message appears, contact the factory and supply the failure code noted in the display. Text in the message identifies
the failed module (for example, H81). If operated on a Process Card failure, the Module Fail self-test seals-in (latches) till
the UR-series device is restarted.

Process Bus Failure Major Self-test

Description: Mission critical data is not available via the process bus. An AC quantity is considered critical if both AC bank
origins and the crosschecking settings are other than none. This self-test is also initiated by an AC input discrepancy being
detected. See the description of the crosschecking setting in this manual for further information. In addition, this self-test
can be initiated by user logic responding to loss of critical contact input/output or other data using the Process Bus Failure
Operand user-programmable self-test setting. This setting is located in the Settings > Product Setup > User-Program-
mable Self Test menu.
If this message appears, first rectify any Process Bus Trouble and Brick Trouble self-test errors. Check the actual value of
the operand referenced by the Process Bus Failure Operand setting, and if “On”, determine the cause and rectify.
Should the problem persist with the foregoing all clear, the cause must be an AC input discrepancy, which is typically the
result of problems in the input signals to the Bricks, or faults in the Brick input conditioning hardware. If the error was
annunciated the first time significant signal was encountered, suspect the former cause and check the copper connections
external to the Brick. Where multiple UR-series devices have self-test errors, look for common causes.
To further isolate AC input discrepancy errors, put the relay in test-isolated mode, then one by one, temporally change an
AC bank crosschecking setting to none, until the Process Bus Failure clears. Once the problem AC bank has been identi-
fied, the values from each of the two Bricks can be examined individually by temporarily mapping each to an AC bank with
a single origin.
Process Bus Trouble Minor Self-Test
Description: Communications problems with one or more Bricks. The text of the message identifies the affected field units.
This self-test is initiated by low received signal levels at either the Brick or Process Card end, and by the sustained failure
to receive poll responses from the proper Brick.
Severity: This self-test error does not directly inhibit protection. However, the affected Brick inputs/outputs may not be avail-
able to the UR-series device.
If this message appears, check the field unit actual values. An indication of equipment mismatch means that messages are
being received from a Brick, but there is a discrepancy between the settings and the actual Brick serial number, order code,
and/or core number. Check that the correct core on the correct Brick is patched through to the correct Process Card port,
and that the field unit settings are correct. An indication of communications loss means that no messages are being
received. Check that the patching is correct, and that the Brick has power. If that is not the problem, use a professional opti-
cal fiber connector cleaning kit to clean both sides of all optical fiber connections from the Process Card through to the
affected Brick. If the problem continues after cleaning, consult the factory.
Brick Trouble Minor Self-Test
7 Description: Brick internal self-testing has detected a trouble internal to the Brick.
Severity: This self-test error does not directly inhibit protection. However, some or all of the affected Brick inputs/outputs
may not be available to the UR-series device.
If this message appears, check the Brick environment for over/under temperatures and the voltage of its power source. If
the ambient temperature and supply voltage are within Brick specifications, consult the factory. Troubles resulting from a
Brick output failing to respond to an output command can only be detected while the command is active, and so in this case
the target is latched. A latched target can be unlatched by pressing the faceplate reset key if the command has ended,
however the output may still be non-functional.
f)

8 THEORY OF OPERATION 8.1 DISTANCE ELEMENTS
8 THEORY OF OPERATION 8.1DISTANCE ELEMENTS 8.1.1 INTRODUCTION
The distance elements use memory voltage for polarization. Additional supervising functions – different for ground and
phase distance zones – complement a classical mho characteristic to enhance directional integrity and reach accuracy:
• To avoid overreaching during resistive faults under heavy pre-fault load conditions, the ground distance elements uti-
lize a load-adaptive (zero-sequence polarized) reactance characteristic to supervise the base mho characteristic.
• Both negative and zero-sequence currents are compared with the memory voltage to enhance directional integrity of
the ground distance elements.
• It is well known that ground distance elements – as per the principle of distance relaying – may have limited accuracy
during double-line-to-ground faults. In order to prevent maloperation in such cases the ground elements are blocked by
an extra “fault-type comparator” that utilizes the phase angle between the negative- and zero-sequence currents.
• The phase distance elements use reactance and memory polarized directional characteristics to supervise the mho
characteristic.
• Both ground and phase distance elements have the current supervision functions built-in.
The quadrilateral distance characteristic uses the reactance, directional, and current supervising functions as described
above. Right and left blinders adjustable as to both the resistive and angular positions complete the characteristic.
More information regarding the distance characteristics is found in the Distance characteristics section. An example of
analysis of the steady-state operation of the distance elements is found in the Distance elements analysis section.
The relay provides five zones of distance protection. All zones are identical in terms of settings. However, zone 1 has extra
adaptive mechanisms built-in to enhance the transient reach accuracy even when the voltage signals are supplied from
poor quality voltage sources such as capacitive voltage transformers (CVTs). Ground zones 2 through 5, in turn, have an
extra zero-sequence directional supervision implemented for their time-delayed operation after the memory expires. Con-
sequently, zone 1 is recommended as an underreaching element, and zones 2 through 5 are recommended as overreach-
ing elements and for time-delayed tripping.
The relay uses offset ground directional overcurrent functions as an optional supplement of the ground distance protection
for pilot-aided schemes. The elements are described in more details in the Ground directional overcurrent section.
The relay provides for an adaptive distance reach control to cope with the overreaching and sub-synchronous oscillations
when applied to, or in a near vicinity of series compensated lines. More details can be found in the Application on series
compensated lines section.
The distance elements use phase angle comparators to shape their characteristics as described in the Distance character-
istics section. The voltage and current phasors are estimated using optimized techniques as explained in the next section.
8.1.2 PHASOR ESTIMATION
The relay samples its input AC signals at 64 samples per power system cycle. A fast and accurate frequency tracking
mechanism ensures accurate filtering and phasor estimation during off-nominal frequency conditions.
The phasor estimation process for both currents and voltages is based on the commonly used Fourier algorithm. Due to a
different nature of signal distortions in the current and voltage signals digital pre-filtering algorithms have been, however,
designed and optimized separately for the current and voltage channels. 8
The current signals are pre-filtered using an improved digital MIMIC filter. The filter removes effectively the DC compo-
nent(s) guaranteeing transient overshoot below 2% regardless of the initial magnitude and time constant of the dc compo-
nent(s). The filter has significantly better frequency response for higher frequencies as compared with a classical MIMIC
filter. This was possible without introducing any significant phase delay thanks to the high sampling rate used by the relay.
The voltage signals are pre-filtered using a special digital filter designed to cope with CVT transients. The patented filter
combines filtering and memory actions enabling the relay to cope with CVT noise under high Source Impedance Ratios
(SIRs). The filter controls underestimation of the fault voltage magnitude to less than 1% of the nominal and prevents cer-
tain phase angle anomalies that can be encountered under heavy CVT noise and high SIRs.

8.1 DISTANCE ELEMENTS 8 THEORY OF OPERATION
8.1.3 DISTANCE CHARACTERISTICS
a) DEFINITIONS
The relay shapes its distance characteristics using phase angle comparators and voltage and current phasors estimated as
described in the previous section.
The following definitions pertain to all of the distance functions:
• IA, IB, IC: phase A, B, and C current phasors.
• IG: ground current from a parallel line.
• VA, VB, VC: phase A to ground, phase B to ground, and phase C to ground voltage phasors.
• ( )_1: positive-sequence phasor of ( ) derived from the phase quantities.
• ( )_2: negative-sequence phasor of ( ) derived from the phase quantities.
• ( )_0: zero-sequence phasor of ( ) derived from the phase quantities.
• ( )M: memorized value of ( ).
• Z: reach impedance (REACH  RCA).
• ZREV: reverse reach impedance for non-directional applications (REV REACH  REV REACH RCA + 180°).
• ZD: directional characteristic impedance (1  DIR RCA).
• ZR: right blinder characteristic impedance: ZR = RGT BLD  sin (RGT BLD RCA)  1 (RGT BLD RCA – 90°).
• ZL: left blinder characteristic impedance: ZL = LFT BLD  sin (LFT BLD RCA)  1 (LFT BLD RCA + 90°).
• K0: zero-sequence compensating factor: K0 = (Z0/Z1 MAG  Z0/Z1 ANG) – 1.
• K0M: mutual zero-sequence compensating factor: K0M = 1/3 x Z0M/Z1 MAG  Z0M/Z1 ANG.
• : non-homogeneity angle setting (NON-HOMOGEN ANG).
b) DIRECTIONAL MHO CHARACTERISTIC

The dynamic 100% memory polarized mho characteristic is achieved by checking the angle between:
• AB phase element: (IA – IB)  Z – (VA – VB) and (VA – VB)_1M
• BC phase element: (IB – IC)  Z – (VB – VC) and (VB – VC)_1M
• CA phase element: (IC – IA)  Z – (VC – VA) and (VC – VA)_1M
• A ground element: IA  Z + I_0  K0  Z + IG  K0M  Z – VA and VA_1M
• B ground element: IB  Z + I_0  K0  Z + IG  K0M  Z – VB and VB_1M
• C ground element: IC  Z + I_0  K0  Z + IG  K0M  Z – VC and VC_1M
The limit angle of the comparator is adjustable enabling the user to shape the characteristic as a mho or a lens as shown in
the figures below.The memory-polarized mho characteristic has an excellent directional integrity built-in as explained in the
Memory polarization section.
8

X Reach setting X Reach setting
Comparator angle setting < 90
Comparator angle setting= 90
R 837715A2.CDR R 837714A2.CDR
MHO CHARACTERISTIC LENS CHARACTERISTIC
Figure 8–1: MHO AND LENS CHARACTERISTICS
c) NON-DIRECTIONAL MHO CHARACTERISTIC

The non-directional mho characteristic is achieved by checking the angle between:
• AB phase element: (IA – IB)  Z – (VA – VB) and (VA – VB) – (IA – IB)  ZREV
• BC phase element: (IB – IC)  Z – (VB – VC) and (VB – VC) – (IB – IC)  ZREV
• CA phase element: (IC – IA)  Z – (VC – VA) and (VC – VA) – (IC – IA)  ZREV
• A ground element:
IA  Z + I_0  K0  Z + IG  K0M  Z – VA and VA – (IA  ZREV + I_0  K0  ZREV + IG  K0M  ZREV)
• B ground element:
IB  Z + I_0  K0  Z + IG  K0M  Z – VB and VB – (IB  ZREV + I_0  K0  ZREV + IG  K0M  ZREV)
• C ground element:
IC  Z + I_0  K0  Z + IG  K0M  Z – VC and VC – (IC  ZREV + I_0  K0  ZREV + IG  K0M  ZREV)
d) MHO REACTANCE CHARACTERISTIC FOR DIRECTIONAL APPLICATIONS

The reactance characteristic is achieved by checking the angle between:
• AB phase element: (IA – IB)  Z – (VA – VB) and (IA – IB)  Z.
• BC phase element: (IB – IC)  Z – (VB – VC) and (IB – IC)  Z.
• CA phase element: (IC – IA)  Z – (VC – VA) and (IC – IA)  Z.
• A ground element: IA  Z + I_0  K0  Z + IG  K0M  Z – VA and I_0  Z.
• B ground element: IB  Z + I_0  K0  Z + IG  K0M  Z – VB and I_0  Z.
• C ground element: IC  Z + I_0  K0  Z + IG  K0M  Z – VC and I_0  Z.
If the mho characteristic is selected, the limit angle of the comparator is adjustable concurrently with the limit angle of the
mho characteristic, resulting in a tent shape complementing the lens characteristic being effectively applied.
8
e) QUADRILATERAL REACTANCE CHARACTERISTIC FOR DIRECTIONAL APPLICATIONS
The quadrilateral reactance characteristic is achieved by checking the angle between:
• AB phase element: (IA – IB)  Z – (VA – VB) and (IA – IB)  Z.
• BC phase element: (IB – IC)  Z – (VB – VC) and (IB – IC)  Z.
• CA phase element: (IC – IA)  Z – (VC – VA) and (IC – IA)  Z.
• A ground element: IA  Z + I_0  K0  Z + IG  K0M  Z – VA and (j  I_0 or j  I_2A)  ej.
• B ground element: IB  Z + I_0  K0  Z + IG  K0M  Z – VB and (j  I_0 or j  I_2B)  ej.
• C ground element: IC  Z + I_0  K0  Z + IG  K0M  Z – VC and (j  I_0 or j  I_2C)  ej.

The ground elements are polarized from either zero-sequence or negative-sequence current as per user-settings to maxi-
mize performance in non-homogenous systems. The polarizing current is additionally shifted by the user-selectable non-
homogeneity correction angle.
f) REVERSE QUADRILATERAL REACTANCE CHARACTERISTIC FOR NON-DIRECTIONAL APPLICATIONS

The reverse quadrilateral reactance characteristic is achieved by checking the angle between:
AB phase element: (IA – IB)  ZREV – (VA – VB) and (IA – IB)  ZREV
BC phase element: (IB – IC)  ZREV – (VB – VC) and (IB – IC)  ZREV
CA phase element: (IC – IA)  ZREV – (VC – VA) and (IC – IA)  ZREV
A ground element: IA  Z + I_0  K0  ZREV + IG  K0M  ZREV – VA and (j  I_0 or j  I_2A)  ej(180 + )
B ground element: IB  Z + I_0  K0  ZREV + IG  K0M  ZREV – VB and (j  I_0 or j  I_2B)  ej(180 + )
C ground element: IC  Z + I_0  K0  ZREV + IG  K0M  ZREV – VC and (j  I_0 or j  I_2C)  ej(180 + )
The ground elements are polarized from either zero-sequence or negative-sequence current as per user-settings to maxi-
mize performance in non-homogenous systems. The polarizing current is additionally shifted by the user-selectable non-
homogeneity correction angle.
g) DIRECTIONAL CHARACTERISTIC
The directional characteristic is achieved by checking the angle between:
AB phase element: (IA – IB)  ZD and (VA – VB)_1M
BC phase element: (IB – IC)  ZD and (VB – VC)_1M
CA phase element: (IC – IA)  ZD and (VC – VA)_1M
A ground element: I_0  ZD and VA_1M
IA_2  ZD and VA_1M
B ground element: I_0  ZD and VB_1M
IB_2  ZD and VB_1M
C ground element: I_0  ZD and VC_1M
IC_2  ZD and VC_1M
The characteristic and limit angles of the directional comparator are adjustable independently from the mho and reactance
comparators. The directional characteristic improves directional integrity of the distance functions.
h) RIGHT BLINDER
The right blinder characteristic is achieved by checking the angle between the following signals:
AB phase element: (IA – IB)  ZR – (VA – VB) and (IA – IB)  ZR
BC phase element: (IB – IC)  ZR – (VB – VC) and (IB – IC)  ZR
CA phase element: (IC – IA)  ZR – (VC – VA) and (IC – IA)  ZR
A ground element: IA  ZR + I_0  K0  ZR + IG  K0M  ZR – VA and IA  ZR + I_0  K0  ZR + IG  K0M  ZR
B ground element: IB  ZR + I_0  K0  ZR + IG  K0M  ZR – VB and IB  ZR + I_0  K0  ZR + IG  K0M  ZR
C ground element: IC  ZR + I_0  K0  ZR + IG  K0M  ZR – VC and IC  ZR + I_0  K0  ZR + IG  K0M  ZR
8 The blinders apply to the Quad characteristic only.
i) LEFT BLINDER
The left blinder characteristic is achieved by checking the angle between the following signals:
AB phase element: (IA – IB)  ZL – (VA – VB) and (IA – IB)  ZL
BC phase element: (IB – IC)  ZL – (VB – VC) and (IB – IC)  ZL
CA phase element: (IC – IA)  ZL – (VC – VA) and (IC – IA)  ZL
A ground element: IA  ZL + I_0  K0  ZL + IG  K0M  ZL – VA and IA  ZL + I_0  K0  ZL + IG  K0M  ZL
B ground element: IB  ZL + I_0  K0  ZL + IG  K0M  ZL – VB and IB  ZL + I_0  K0  ZL + IG  K0M  ZL
C ground element: IC  ZL + I_0  K0  ZL + IG  K0M  ZL – VC and IC  ZL + I_0  K0  ZL + IG  K0M  ZL
The blinders apply to the Quad characteristic only.

j) FAULT-TYPE CHARACTERISTIC
The fault-type characteristic applies to ground elements only and is achieved by checking the angle between:
A ground element: I_0 and IA_2;
B ground element: I_0 and IB_2
C ground element: I_0 and IC_2
The limit angle of the comparator is not adjustable and equals 50°. The fault-type characteristic is intended to block the
ground distance elements during double-line-to-ground faults.
k) ZERO-SEQUENCE DIRECTIONAL CHARACTERISTIC

The extra zero-sequence characteristic applies to ground zones 2 and higher and is achieved by checking angles between:
A ground element: I_0  ZD and –V_0
B ground element: I_0  ZD and –V_0
C ground element: I_0  ZD and –V_0
The limit angle of the comparator is not adjustable and equals 90°. The zero-sequence directional characteristic improves
directional integrity for time-delayed operations after the memory expires.
l) OVERCURRENT SUPERVISION
The overcurrent supervision responds to the following currents:
AB phase element: (IA – IB) / 3
BC phase element: (IB – IC) / 3
CA phase element: (IC – IA) / 3
A, B, C ground element: | 3  I_0 – 0.05 × I_1 |
The following tables summarize the characteristics of the distance elements
Table 8–1: DIRECTIONAL MHO PHASE DISTANCE FUNCTIONS

CHARACTERISTIC COMPARATOR INPUTS LIMIT ANGLE
Variable mho IZ–V V_1M COMP LIMIT
Reactance IZ–V IZ COMP LIMIT
Directional I  ZD V_1M DIR COMP LIMIT
Table 8–2: DIRECTIONAL MHO GROUND DISTANCE FUNCTIONS

Variable mho IZ–V V_1M COMP LIMIT
Reactance IZ–V I_0  Z COMP LIMIT
Directional I_0  ZD V_1M DIR COMP LIMIT
Directional I_2  ZD V_1M DIR COMP LIMIT (removed when 3I_0 > OC SUPV and
I_2 < CUTOFF)
Fault-type I_0 I_2 50° (removed during open pole conditions or when 3I_0 > OC 8
SUPV and I_2 < CUTOFF)
Zero-sequence I_0  ZD –V_0 90° (zones 2 and higher only; removed for zones 2 and higher
during open pole conditions)
Table 8–3: DIRECTIONAL QUADRILATERAL PHASE DISTANCE FUNCTIONS

Reactance IZ–V IZ COMP LIMIT
Directional I  ZD V_1M DIR COMP LIMIT
Right Blinder I  ZR – V I  ZR 90°
Left Blinder I  ZL – V I  ZL 90°

Table 8–4: DIRECTIONAL QUADRILATERAL GROUND DISTANCE FUNCTIONS

Reactance IZ–V j  I_0  ej or j  I_2  ej COMP LIMIT
Directional I_0  ZD V_1M DIR COMP LIMIT
Directional I_2  ZD V_1M DIR COMP LIMIT (removed when 3I_0 > OC SUPV
and I_2 < CUTOFF)
Fault-type I_0 I_2 50° (removed during open pole conditions or when
3I_0 > OC SUPV and I_2 < CUTOFF)
Zero-sequence I_0  ZD –V_0 90° (zones and higher only; removed for zones 2 and
higher during open pole conditions)
Table 8–5: NON-DIRECTIONAL MHO PHASE DISTANCE FUNCTIONS

Offset mho IZ–V V-I  ZREV COMP LIMIT
Table 8–6: NON-DIRECTIONAL MHO GROUND DISTANCE FUNCTIONS

Offset mho IZ–V V-I  ZREV COMP LIMIT
Fault-type I_0 I_2 50° (removed during open pole conditions or when 3I_0 > OC
SUPV and I_2 < CUTOFF)
Table 8–7: NON-DIRECTIONAL QUADRILATERAL PHASE DISTANCE FUNCTIONS

Forward Reactance IZ–V IZ COMP LIMIT
Reverse Reactance I  ZREV – V I  ZREV COMP LIMIT
Table 8–8: NON-DIRECTIONAL QUADRILATERAL GROUND DISTANCE FUNCTIONS

Forward Reactance IZ–V j  I_0  ej or j  I_2  ej COMP LIMIT
Reverse Reactance I  ZREV – V –j  I_0  ej or –j  I_2  ej COMP LIMIT
Fault-type I_0 I_2 50° (removed during open pole conditions or
when 3I_0 > OC SUPV and I_2 < CUTOFF)
8 8.1.4 MEMORY POLARIZATION
All distance functions use memory polarization. The positive-sequence voltage – either memorized or actual – is used as a
polarizing signal. The memory is established when the positive-sequence voltage remains above 80% of its nominal value
for five power system cycles. The memory voltage is a three-cycle old voltage.
Once established, the memory is applied for the user-specified time interval. The memory timer is started when the voltage
drops below 80% of nominal or when the user-programmable condition is asserted to force memory polarization. After the
memory expires, the relay checks the magnitude of the actual positive-sequence voltage. If it is higher than 10% of nomi-
nal, the actual voltage is used; if lower, the memory voltage continues to be used.
A provision is added to force self-polarization from any user-programmable condition.
The memory-polarized mho has an extra directional integrity built-in as illustrated below. The self-polarized mho character-
istic is shifted in the reverse direction for a forward fault by an amount proportional to the source impedance, and in the for-
ward direction for a reverse fault.

Self-polarized mho
Memory-polarized mho
Memory-polarized mho (Forward fault)
(Reverse fault)
837719A2.CDR
Figure 8–2: DYNAMIC SHIFT OF THE MHO CHARACTERISTIC

The same desirable effect of memory polarization applies to the directional comparator of the quadrilateral characteristic.
Memory-
polarized
(Reverse fault)
Self-polarized
Memory-
polarized
837724A1.CDR
(Forward fault)
Figure 8–3: DYNAMIC SHIFT OF THE MEMORY-POLARIZED DIRECTIONAL CHARACTERISTIC

Mutual zero-sequence compensation may raise concerns regarding directional integrity on reverse faults in the situation
when the relay gets ‘overcompensated’. This problem does not affect the D60 because its ground distance elements use
zero-sequence and negative-sequence currents in extra directional comparators. Both the currents are from the protected
line and are not affected by any compensation as the latter applies only to the reach defining comparators: the mho, reac-
tance and blinder characteristics.
8.1.5 DISTANCE ELEMENTS ANALYSIS
a) DESCRIPTION 8
This subsection shows how to analyze the operation of the distance elements in steady states using the results of short cir-
cuit studies. All quantities are secondary ohms, volts, and amperes. Ground phase A and phase AB distance elements are
analyzed.
Assume the following settings have been entered:
Phase Rotation: ABC
Right Blinder Reach: 10 
Nominal Secondary Voltage: 69.28 V
Right Blinder RCA: 88°
Distance Reach: 14 
Left Blinder Reach: 5 
Distance RCA: 88°

Left Blinder RCA: 88°

Polarizing Current: Zero-sequence
Non-Homogeneity Correction Angle: 3°
Directional RCA: 88°
Z0/Z1 Magnitude: 4.55
Overcurrent supervision: 3 A
Z0/Z1 Angle: –12°
Distance Comparator limit angle: 75°
Z0M/Z1 Magnitude: 0
Directional Comparator limit angle: 75°
Assume the following signals are injected to the relay:
VA = 64.71 V 0.0° (pre-fault)
VA = 25.43 V –19.9°
VB = 80.22 V –133.5°
VC = 77.33 V 135.7°
IA = 4.47 A –107.8°
IB = 2.92 A 68.9°
IC = 2.93 A –51.1°
Based on the entered setting the relay calculates:
K0 = 3.58 –15.2°
K0M= 0
Z = 14.00  88°
ZD = 1  88°
ZR = 9.99  2°
ZL = 4.99  178°
For the assumed steady-state injection the relay calculates:
VA_1 = 58.83 V –2.1°
VA_1M = 64.71 V 0.0°
I_0 = 1.37 A –68.2°
IA_2 = 1.37 A –68.1°
–V_0 = 29.18 V 8.4°
(VA–VB)_1 = 93.35 V 32.0°
(VA–VB)_1M = 112.08 V 30.0°
IA–IB = 7.39 A –109.1°
8 b) MHO PHASE A TO GROUND ELEMENT (BEFORE MEMORY EXPIRES)

IA  Z + I_0  K0  Z + IA  K0M  Z – VA = 103.33 V –3.9°
VA_1M = 64.71 V 0.0°
IA_2  ZD = 1.37 V 19.8°
I_0  Z = 19.11 V 19.8°
I_0  ZD = 1.37 V 19.8°
• Overcurrent supervision: | 3  I_0 | = 4.09 A  3 A
• Mho difference angle = | –3.9° – 0° | = 3.9°  75°
• Reactance difference angle = | –3.9° – 19.8° | = 23.7°  75°
• Zero-sequence directional difference angle = | 19.8° – 0.0° | = 19.8°  75°
• Negative-sequence directional difference angle = | 19.8° – 0.0° | = 19.8°  75°
• Fault-type comparator difference angle = | 19.8° – 19.8° | = 0.0°  50°

All four comparators and the overcurrent supervision are satisfied.

The MHO phase A ground element will operate for this fault.
c) MHO PHASE A TO GROUND ELEMENT (AFTER MEMORY EXPIRES)

After the memory expires, the relay checks the actual positive-sequence voltage and compares it with 10% of the nominal
voltage:
| VA_1 | = 58.83 V  0.1  69.28 V
After the memory expires the relay will use the actual voltage for polarization.
IA  Z + I_0  K0  Z + IG  K0M  Z – VA = 103.33 V –3.9°
VA_1 = 58.83 V –2.1°
IA_2  ZD = 1.37 V 19.8°
I_0  Z = 19.11 V 19.8°
I_0  ZD = 1.37 V 19.8°
• Mho difference angle = | –3.9° – (–2.1°) | = 1.8°  75°
• Zero-sequence directional difference angle = | 19.8° – (–2.1°) | = 21.9°  75°
• Negative-sequence directional difference angle = | 19.8° – (–2.1°) | = 21.9°  75°
All four comparators and the overcurrent supervision are satisfied.
The Zone 1 MHO phase A ground element will operate for this fault.
• Zero-sequence directional difference angle for zones 2 and higher (phase A) = | 19.8° – 8.4° | = 11.4°  90°.
Zones 2 and hihger phase A ground elements will pick-up, time-out and operate.
d) MHO AB PHASE ELEMENT

(IA – IB)  Z – (VA – VB) = 88.65 V –78.7°
(VA – VB)_1M = 112.08 V 30.0°
(IA – IB)  Z = 103.50 V –21.2°
(IA – IB)  ZD = 7.39 V –21.2°
• Overcurrent supervision: | (IA – IB) / 3 | = 4.27 A  3 A
• Mho difference angle = | –78.7° – 30.0° | = 108.7°  75°
• Reactance difference angle = | –78.7° – (–21.2°) | = 57.5°  75°
• Directional difference angle = | –21.2° – 30.0° | = 51.2°  75°
The mho comparator is not satisfied.
The MHO AB phase element will not operate for this fault.
Repeating the above analysis one concludes that out of the six distance elements only the ground element in phase A will 8
operate for this fault.
e) QUAD PHASE A TO GROUND ELEMENT (BEFORE MEMORY EXPIRES)

IA  Z + I_0  K0  Z + IG  K0M  Z – VA = 103.33 V –3.9°
VA_1M = 64.71 V 0.0°
j  I_0  ej3 = 1.37 A 24.8°
IA_2  ZD = 1.37 V 19.8°
I_0  ZD = 1.37 V 19.8°
IA  ZR + I_0  K0  ZR + IG  K0M  ZR – VA= 87.6 V –109.2°
IA  ZR + I_0  K0  ZR = 91.5 V –93.0°

IA  ZL + I_0  K0  ZL + IG  K0M  ZL– VA= 57.0 V 108.7°

IA  ZL + I_0  K0  ZL = 45.8 V 82.9°
• Zero-sequence difference angle = | –19.8° – 0.0° | = 19.8°  75°
• Negative-sequence directional difference angle = | –19.8° – 0.0° | = 19.8°  75°
• Right blinder difference angle = | –93.0° – (–109.2°) | = 16.2°  90°
• Left blinder difference angle = | 82.9° – 108.7° | = 25.8°  90°
All six comparators and the overcurrent supervision are satisfied.
The Quad Phase A ground element will operate for this fault.

8 THEORY OF OPERATION 8.2 PHASE DISTANCE APPLIED TO POWER TRANSFORMERS
8.2PHASE DISTANCE APPLIED TO POWER TRANSFORMERS 8.2.1 DESCRIPTION
As a Wye-Delta transformer introduces discontinuity for the zero-sequence circuit, the ground distance protection cannot
be applied, except special circumstances, to respond to faults behind the transformer.
The phase distance elements, however, could be developed so that both accurate reach and correct fault phase identifica-
tion is retained for faults behind the power transformer as seen from the relaying point. Without appropriate compensation,
the relay's reach would depend on a type of fault, creating considerable difficulties in applying the relay.
The D60 provides for any location of the VTs and CTs with respect to the involved power transformer and the direction of
any given zone.
In the following equations, the VT and CT locations are referenced as “None” if the transformer is not present between the
CT/VT and the intended reach point. Otherwise, the location is to be selected as a type of a transformer as seen from the
VT/CT position towards the intended reach point. The following figure explains the adopted rules.
(a) (b)
delta wye, 330o lag delta wye, 330o lag
Z4 Z4
Z4 XFRM VOL CONNECTION = None Z4 XFRM VOL CONNECTION = Yd1

Z4 XFRM CUR CONNECTION = None Z4 XFRM CUR CONNECTION = None
Z1 Z1
Z1 XFRM VOL CONNECTION = Dy11 Z1 XFRM VOL CONNECTION = None

Z1 XFRM CUR CONNECTION = Dy11 Z1 XFRM CUR CONNECTION = Dy11
(c) (e)
delta wye, 330o lag
L1 L2
Z4 Zone 4
Zone 1
Z4 XFRM VOL CONNECTION = None
Z4 XFRM CUR CONNECTION = Yd1 ZL1 ZT ZL2
Z1 8
Z1 XFRM VOL CONNECTION = Dy11
Z1 XFRM CUR CONNECTION = None
Figure 8–4: APPLICATIONS OF THE “PHS DIST XFMR VOL/CUR CONNECTION” SETTINGS

8.2 PHASE DISTANCE APPLIED TO POWER TRANSFORMERS 8 THEORY OF OPERATION
Table 8–9: PHASE DISTANCE INPUT SIGNALS FOR DELTA-WYE TRANSFORMERS

TRANSFORMER LOOP CURRENT VOLTAGE
CONNECTION TRANSFORMATION TRANSFORMATION
None AB IA – IB V AB
BC IB – IC V BC
CA IC – IA V CA
Dy1 AB 1-
3I A ------  V AB – V CA 
3
BC 1-
3I B ------  V BC – V AB 
3
CA 1-
3I C ------  V CA – V BC 
3
Dy3 AB 1
I AB_21P = – 3I C V AB_21P = -------  V BC – V CA 
3
BC 1
I BC_21P = – 3I A V BC_21P = -------  V CA – V AB 
3
CA 1
I CA_21P = – 3I B V CA_21P = -------  V AB – V BC 
3
Dy5 AB 1
I AB_21P = – 3I B V AB_21P = -------  V BC – V AB 
3
BC 1
I BC_21P = – 3I C V BC_21P = -------  V CA – V BC 
3
CA 1
I CA_21P = – 3I A V CA_21P = -------  V AB – V CA 
3
Dy7 AB 1
I AB_21P = – 3I A V AB_21P = -------  V CA – V AB 
3
BC 1
I BC_21P = – 3I B V BC_21P = -------  V AB – V BC 
3
CA 1
I CA_21P = – 3I C V CA_21P = -------  V BC – V CA 
3
Dy9 AB 1
I AB_21P = – 3I C V AB_21P = -------  V CA – V BC 
8 BC 1
3
I BC_21P = – 3I A V BC_21P = -------  V AB – V CA 

3
CA 1
I CA_21P = – 3I B V CA_21P = -------  V BC – V AB 
3
Dy11 AB 1
I AB_21P = – 3I B V AB_21P = -------  V AB – V BC 
3
BC 1
I BC_21P = – 3I C V BC_21P = -------  V BC – V CA 
3
CA 1
I CA_21P = – 3I A V CA_21P = -------  V CA – V AB 
3

Table 8–10: PHASE DISTANCE INPUT SIGNALS FOR WYE-DELTA TRANSFORMERS

TRANSFORMER LOOP CURRENT VOLTAGE
CONNECTION TRANSFORMATION TRANSFORMATION
Yd1 AB 1
I AB_21P = -------  2I A – I B – I C  V AB_21P = 3V A
3
BC 1
I BC_21P = -------  2I B – I A – I C  V BC_21P = 3V B
3
CA 1
I CA_21P = -------  2I C – I A – I B  V CA_21P = 3V C
3
Yd3 AB 1
I AB_21P = -------  I A + I B – 2I C  V AB_21P = – 3V C
3
BC 1
I BC_21P = -------  I B + I C – 2I A  V BC_21P = – 3V A
3
CA 1
I CA_21P = -------  I A + I C – 2I B  V CA_21P = – 3V B
3
Yd5 AB 1
I AB_21P = -------  2I B – I A – I C  V AB_21P = 3V B
3
BC 1
I BC_21P = -------  2I C – I A – I B  V BC_21P = 3V C
3
CA 1
I CA_21P = -------  2I A – I B – I C  V CA_21P = 3V A
3
Yd7 AB 1
I AB_21P = -------  I B + I C – 2I A  V AB_21P = – 3V A
3
BC 1
I BC_21P = -------  I A + I C – 2I B  V BC_21P = – 3V B
3
CA 1
I CA_21P = -------  I A + I B – 2I C  V CA_21P = – 3V C
3
Yd9 AB 1
I AB_21P = -------  2I C – I A – I B  V AB_21P = 3V C
3
BC 1
I BC_21P = -------  2I A – I B – I C  V BC_21P = 3V A
3
CA 1
I CA_21P = -------  2I B – I A – I C  V CA_21P = 3V B
3 8
Yd11 AB 1
I AB_21P = -------  I A + I C – 2I B  V AB_21P = – 3V B
3
BC 1
I BC_21P = -------  I A + I B – 2I C  V BC_21P = – 3V C
3
CA 1
I CA_21P = -------  I B + I C – 2I A  V CA_21P = – 3V A
3

8.2 PHASE DISTANCE APPLIED TO POWER TRANSFORMERS 8 THEORY OF OPERATION
Equations from the “Current Transformation” and “Voltage Transformation” columns are used to derive inputs to the three
(AB, BC, and CA) phase distance elements. For example, if the CTs are located at the delta side of the Delta-Wye 11 trans-
former, and a given zone is set to look through the transformer into the system connected to the Wye winding, the CT loca-
tion setting for that zone shall be set to Dy11 and the relay would use – 3I B instead of a traditional I A – I B for the AB
phase distance element.
The current supervision pickup setting applies to the currents specified in the “Current Transformation” columns.
A distance zone originates at the location of the VTs (regardless of the location of the CTs). For more information on set-
tings please refer to Chapter 9: Application of Settings.
8.2.2 EXAMPLE
Consider the system shown below:
150 MVA, 10%

13.8kV/315kV
delta wye, 330° lag
AB
ZL = 30.11Ω∠85°
H X
VT = 13.8kV/120V VT = 315kV/120V
CT = 8000:5 CT = 300:5
0.688Ω∠85°
2.57Ω∠88.4°
837727A2.CDR
Figure 8–5: SAMPLE SYSTEM CONFIGURATION

Normally, in order to respond to the fault shown in the figure, a distance relay shall be applied at the relaying point X. The
relay input signals at this location are shown in the following table.
INPUT PRIMARY SECONDARY

VA 100.4 kV –7.32° 38.25 V –7.32°
VB 97.23 kV –53.4° 37.04 V –53.4°
VC 181.8 kV –150.0° 69.26 V –150.0°
IA 1.288 kA –27.6° 21.47 A –27.6°
8 IB
IC
1.288 kA 152.4°
0
21.47 A 152.4°
0
If installed at the location X, the relay would use the following input signals for its phase AB distance element:
V = VAB = 77.402 kV 57.5° primary or 29.49 V 57.5° secondary
I = IA – IB = 2.576 kA –27.6° primary or 42.93 A –27.6° secondary
And consequently it would see an apparent impedance of:
Zapp = V / I = 30.05  85° primary or 0.687  85° secondary

If applied at location H, the relay sees the following input signals:
INPUT PRIMARY SECONDARY

VA 7.584 kV –5.59° 69.95 V –5.59°
VB 6.269 kV –120.1° 54.52 V –120.1°
VC 7.751 kV 125.5° 65.84 V 125.5°
IA 16.976 kA –27.6° 10.61 A –27.6°
IB 33.952 kA 152.4° 21.22 A 152.4°
IC 16.976 kA –27.6° 10.61 A –27.6°
The relay is set as follows:

XFMR VOL CONNECTION = “Dy11”
XFMR CUR CONNECTION = “Dy11”
Consequently, the following signals are applied to the phase AB distance element:
1
V = ------- V AB – V BC = 10.861 kV 59.9 primary or 94.45 V 59.9 secondary (EQ 8.1)
3
I = – 3I B = 58.860 kA – 27.6 primary or 36.75 A – 27.6 secondary (EQ 8.2)
This results in the following apparent impedance:

V 94.45 kV 59.9
Z app = ---- = ---------------------------------------------- = 2.570  87.5 secondary (EQ 8.3)
I 36.75 kA – 27.6 
The above value is a correct measure of the distance from the VT location to the fault. For relay location 2, this certainly
includes the positive-sequence impedance of the transformer:
2
10  13.8 kV 
Z T  at 13.8 kV  = ----------  ---------------------------- = 0.127 90
100 150 MVA
(EQ 8.4)
13.8 2
Z L  at 13.8 kV  = 30.11   ----------- = 0.05779 85
 315 
Thus, 0.127  90° + 0.05779  85° = 0.1847  88.4° primary side or 2.569  88.4° on the secondary side.
The above example illustrates how the relay maintains correct reach for fault behind power transformers. When installed at
X, the relay shall be set to 0.687  85° secondary in order to reach to the fault shown in the figure. When installed at H,
the relay shall be set to 2.569  88.4° to ensure exactly same coverage.
See Chapter 9: Application of Settings for more information on setting calculations.

8.3 GROUND DIRECTIONAL OVERCURRENT 8 THEORY OF OPERATION
8.3GROUND DIRECTIONAL OVERCURRENT 8.3.1 DESCRIPTION
Consider the negative-sequence directional overcurrent element. As illustrated below, the negative-sequence voltage could
be low during internal fault conditions.
(a) (b)
S_op
S_pol
V_2 -V_2 I_2 x Z
V_2 ECA
UR I_2
(c) (d)
I_2 x Z S_pol S_op
-V_2 -V_2 V_2

V_2 >
I_2 * Z_2line ECA
I_2
UR
Figure 8–6: OFFSET IMPEDANCE AUGMENTATION

In order to ensure operation of the element under such circumstances the angle comparator uses a polarizing voltage aug-
mented by the negative-sequence current as per following equations:
Forward-looking element:
S_pol = – V_2 + I_2  Z_offset  1 ECA
(EQ 8.5)
S_op = I_2  1 ECA
Reverse-looking element:
S_pol = – V_2 + I_2  Z_offset  1 ECA
(EQ 8.6)
S_op = – I_2  1 ECA
Where ECA = forward ECA angle (maximum torque angle) and Z_offset = offset impedance. The effect of the augmentation
for forward and reverse fault is shown in the figures above. As long as the offset impedance is not higher than the negative-
sequence line impedance the element will ensure correct and fast fault direction identification for both forward and reverse
faults. The same principle applies to the neutral directional overcurrent element.
8.3.2 EXAMPLE
Consider relay input signals as in the Distance Elements Analysis section and assume an offset impedance of 4  and
8 ECA and limit angles of 88° and 90°, respectively. The relay calculates the following negative-sequence quantities:
V_2 = 6.39 V –159.6°; I_2 = 1.37 A –68.1°; I_1 = 2.94 A –144.2°
and the following signals for the directional unit of the negative-sequence directional overcurrent element:
• Forward-looking element: S_pol = 11.87 V 20.2
S_op = 1.37 V 20.2
• Reverse-looking element: S_pol = 11.87 V 20.2

S_op = 1.37 V – 160.0 
After comparing the angles, a solid forward indication is given.
Assume further the pickup setting of 0.25 A for both forward and reverse directions, and the “Negative-sequence” mode
setting entered for the overcurrent unit of the element. The relay calculates the operating signal using the positive-
sequence restraint:

8 THEORY OF OPERATION 8.3 GROUND DIRECTIONAL OVERCURRENT
I_op = |I_2| – |I_1| / 8 = 1.003 A > 0.25 A.

The overcurrent unit will pickup and the element will operate in the forward direction.

8.4 SERIES COMPENSATED LINES 8 THEORY OF OPERATION
8.4SERIES COMPENSATED LINES 8.4.1 DESCRIPTION
Faults on or in a close vicinity of series compensated lines may create problems for distance protection:
• Voltage and/or current inversion may lead to false direction discrimination by directional elements. This may potentially
include both a failure to operate on a forward in-zone fault as well as misoperation on a reverse fault. Both distance
and overcurrent directional elements can be affected.
• Series-capacitors and their overvoltage protection equipment (air gaps and/or Metal-Oxide Varistors) have a steady-
state overreaching effect on the apparent impedance seen by the relay - a forward fault may appear much closer to the
relay as compared with the actual fault location. The apparent impedance may be shifted towards the relay by as much
as the total reactance of the series capacitors placed between the potential source of the relay and the fault point. This
extreme steady-state overreach happens during low-current faults when the air-gaps do not flashover or the MOVs do
not conduct any significant current.
• In addition to the above steady-state overreach effect; sub-synchronous oscillations in both currents and voltages may
cause significant transient overreach.
Distance protection elements of the D60 deal with the problem of voltage inversion by using 100% memory polarized direc-
tional comparators. As the memory duration is set longer that the slowest fault clearing time for reverse faults, it is guaran-
teed that the distance element would not pick-up on reverse faults should the voltage inversion happen.
At the same time, it is guaranteed that the distance elements would pick-up for all forward faults regardless of any voltage
inversion as long as the memory voltage is used. Before the memory expires the relay would respond to any fault on the
protected line. Stepped distance backup zones operate after the memory voltage expires. But the backup protection
responds to distant faults that do not cause any inversion of the positive-sequence voltage. As a result, the time-delayed
stepped-distance zones are guaranteed to operate.
Distance protection elements of the D60 deal with the problem of current inversion by using a multi-input-comparator
approach as described in the Distance Characteristics subsection. Should the current inversion happen, the distance ele-
ments are secure on reverse faults because multiple conditions involving fault-loop, negative-sequence and zero-sequence
currents and the memory voltage are checked prior to declaring a forward fault.
On close-in forward faults beyond the series capacitors as seen from the relaying point, the current inversion phenomenon
may take place for a short period of time. The condition cannot sustain for a long time as very high fault currents would
occur causing large voltage drops across the series capacitors and prompting the overvoltage protection of the capacitors
to operate quickly. This would effectively remove the series compensation and eliminate the current inversion. However,
when the currents used by distance comparator (fault-loop current for ground and phase distance protection, and the nega-
tive- and zero-sequence currents for ground elements) stay shifted by more than 90 degrees from their natural fault position
determined by the user as the element characteristic angle, the distance elements may fail to pick-up on such a forward
fault for the brief period of current inversion. This is an inherent attribute of the 100% memory polarized mho element, and
not a weakness particular to the D60 relay.
Therefore, for dependability, it is recommended to use high-set phase overcurrent protection for direct tripping on close-in
faults potentially causing current inversion, and overreaching ground fault directional overcurrent functions (such as nega-
tive-sequence, ground or neutral) for communication-aided schemes.
The problem of steady-state overreaching due to the negative reactance of the series capacitors may be addressed in the
D60 in a traditional way by shortening the reach of an underreaching distance elements to the net inductive reactance of
8 the line between the potential source and the far end busbar(s). This generic approach has two major drawbacks. First, it
leaves large portion of the line uncovered by the directly tripping distance protection. Second, it does not solve the transient
overreaching problem caused by sub-synchronous oscillations.
Therefore, the D60 offers a unique option for dynamic reach control that is effectively based on the magnitude of the current
flowing through the series capacitor bank(s). The underreaching distance functions can be set as for plain uncompensated
line, i.e. using the impedance of the line alone, and the relay would control an effective reach accordingly using the current
magnitude as illustrated in the figure below.
The reach is reduced sufficiently to cope with both steady-state and transient overreach phenomena. For large degrees of
compensation and small-current faults, the transient overreach may be as high as 100%. This means that fast distance pro-
tection is not achievable. The adaptive D60's mechanism would guarantee security on external faults. Overreaching ground
fault directional overcurrent functions (such as negative-sequence, ground or neutral) shall be used for dependability.

8 THEORY OF OPERATION 8.4 SERIES COMPENSATED LINES
X FAR
-E
BUS ND
BAR
SET REACH (ZR)
THE REACH IS
DYNAMICALLY ACTUAL REACH
REDUCED BY FOR VERY HIGH
VL/abs(I) CURRENTS
ACTUAL REACH IS
A FUNCTION OF
CURRENT
MAGNITUDE
ACTUAL REACH
FOR VERY SMALL
CURRENTS R
837729A1.CDR
Figure 8–7: DYNAMIC REACH CONTROL

Section (a) of the figure below shows the effect of adaptive reach control for low-current external fault. The reach is reduced
sufficiently to cope with both transient and steady-state overreach. Section (b) shows a high-current external fault. The air
gaps or MOVs conduct majority of the fault current and neither steady-state nor transient overreach takes place. The relay
does not reduce its reach as it is not necessary. Section (c) shows a high-current internal fault. Because of the large cur-
rent, the reach is not reduced and the element responds to this internal fault. Traditional approach would leave this fault out
of the relay reach.
The neutral and negative-sequence directional protection functions of the relay cope with the voltage and/or current inver-
sions by adding appropriate offset to their polarizing signals as explained in the Ground Directional Overcurrent section.
The offset impedance can always be successfully selected to guarantee correct fault direction discrimination regardless of
the degree of compensation and location of the series capacitors and the potential source.
Refer to Chapter 9: Application of Settings for detailed recommendations on settings for series compensation applications.

8.4 SERIES COMPENSATED LINES 8 THEORY OF OPERATION
(a) LOW-CURRENT EXTERNAL

X
FAULT
FAR-E
N
BUSB D
AR
Impedance
RF
Trajectory
Set reach
Z SC&MOV
Steady-state
apparent
impedance
SC
The reach is safely
M OV
reduced
R
HIGH-CURRENT EXTERNAL
(b) FAULT
X
FAR-E
N
BUSB D Impedance
AR
RF Trajectory (no
Set reach subsynchronous
oscillations)
Steady-state
apparent
impedance
SC
The reach is not

M OV
reduced
(c) HIGH-CURRENT INTERNAL

X
FAULT
FAR-E
N
BUSB D
AR
Set reach Impedance
Trajectory (no
8 RF
subsynchronous
oscillations)
Steady-state
apparent
impedance
SC
The reach is not

M OV
reduced
837730A1.CDR
Figure 8–8: DYNAMIC REACH FOR INTERNAL AND EXTERNAL FAULTS

8 THEORY OF OPERATION 8.5 SINGLE-POLE TRIPPING
8.5SINGLE-POLE TRIPPING 8.5.1 OVERVIEW
a) INTRODUCTION
Single pole operations make use of many features of the relay. At the minimum, the trip output, recloser, breaker control,
open pole detector, and phase selector must be fully programmed and in service; and either protection elements or digital
inputs representing fault detection must be available for successful operation. When single pole trip-and-reclose is required
overall control within the relay is performed by the trip output element. This element includes interfaces with pilot aided
schemes, the line pickup, breaker control, and breaker failure elements.
Single pole operations are based on use of the phase selector to identify the type of the fault, to eliminate incorrect fault
identification that can be made by distance elements in some circumstances and to provide trip initiation from elements that
are not capable of any fault type identification, such as high-set negative-sequence directional overcurrent element. The
scheme is also designed to make use of the advantages provided by communications channels with multiple-bit capacities
for fault identification.
Phase selector
Volts Reset
and output Fault locator
amps
Block specific protection elements
Volts
and
Trip output amps
Protection Setting
elements
Single-pole
Single-pole
trip request
Inputs Setting trip
Open
Pilot-
pole
aided
detector
schemes
Trip
A or B or C
Setting Setting
Inputs Outputs Initiate breaker

Single-pole failure
operation
Communications
channels Breaker Breaker
1 and 2 1 and 2
AG SLG pole state out-of-service
BG faulted
CG phase
Setting Permission
Breaker 1 and 2
Inputs
Setting
Reset Breaker
control
Outputs
Three-pole Three-pole
trip trip
request
Line pickup Setting
CLOSE 1
CLOSE 2
CLOSE 1
CLOSE 2
Multi-phase
Operator
Void Force Three-pole
three-oole operation
Setting operation Setting
AR FORCE 3-P
8
Initiate
Reclose request Trip
Initiate
AR Initiate 3-Pole Recloser
Multi-phase
837026A5.CDR
Figure 8–9: SINGLE-POLE OPERATION

The trip output element receives requests for single and three pole trips and three pole reclose initiation, which it then pro-
cesses to generate outputs that are used to:
• Determine whether a single or three pole operation should be performed.
• Initiate tripping of breaker poles A, B and C, either individually or as a group.
• Initiate breaker failure protection for phases A, B and C, either individually or as a group.
• Notify the open pole detector when a single pole operation is imminent.
• Initiate either single or three pole reclosing.

8.5 SINGLE-POLE TRIPPING 8 THEORY OF OPERATION
• Notify the phase selector when a trip operation is imminent.

When notified that a single pole operation has been initiated open pole detector will:
• Initiate blocking of protection elements that could potentially maloperate when a breaker pole is open.
• Instruct the phase selector to de-assert all outputs, as an open pole invalidates calculations.
The operation of the scheme on a line in a single breaker arrangement will be described. The line is protected by a D60
relay using the line pickup and zone 1 phase and ground distance elements, and a permissive overreaching transfer trip
scheme (using zone 2 phase and ground distance elements as well as negative-sequence directional overcurrent ele-
ments, GND DIR O/C FWD: “NEG SEQ OC1 FWD”, GND DIR O/C REV: “NEG SEQ OC1 REV”). Zone 1 is configured to issue a sin-
gle-pole trip when appropriate (TRIP 1-POLE INPUT-1: “GND DIST Z1 OP”, TRIP 1-POLE INPUT-2: “PHS DIST Z1 OP”). By default
the POTT scheme will issue a single-pole trip. It is assumed that when tripping three-poles both the zone 1 and the POTT
shall initiate three-pole reclosing. This is achieved by setting TRIP RECLOSE INPUT-1: “POTT TRIP 3P”, TRIP RECLOSE INPUT-2:
“GND DIST Z1 OP”, and TRIP RECLOSE INPUT-3: “PHS DIST Z1 OP”.
It is assumed for this discussion that the relay features that are shown on Single pole operation diagram above have all
been programmed for the application and are in service. The description begins with line breakers open at both the local
and remote ends, and the operation of the scheme is described in chronological order.
Because the line is de-energized the line pickup element is armed. The recloser is presently enabled. An operator requests
that breaker control close the breaker, and it operates output relays to close breaker poles A, B and C. This operator man-
ual close request is also forwarded from breaker control to recloser, which becomes disabled, de-asserting its “Enabled”
output. This output is transferred to trip output, where it converts any input request for a single pole operation into a three-
pole operation. At the recloser, the AR1 BLK TIME @ MAN CLOSE timer is started.
The breaker closes and status monitoring contacts on the breaker poles change state; the new breaker pole states are
reported to breaker control, which in turn transfers these states to the recloser, trip output, breaker failure and open pole
detector. Because a fault is not detected the AR1 BLK TIME @ MAN CLOSE times out and the recloser is enabled, which
asserts the “Enabled” output, informing the trip output element that single pole trip operations are now permitted. When nor-
mal voltage appears on the line the line pickup element is disarmed. As the local line breaker has not tripped the operator
closes the breaker at the remote end of the line, placing the line in service.
Several scenarios are considered below.
b) SLG FAULT
An AG fault occurs close to the considered relay. Immediately after the fault, the disturbance detector (50DD) picks-up and
activates the phase selector. The phase selector recognizes an AG fault by asserting its PHASE SELECT AG operand.
Ground distance zone 1 (AG element) responds to the fault. As the fault is close to the relay, phase distance zone 1 (AB,
CA elements) may respond to this fault as well. In any case, a single-pole operation is requested by zone 1 via the GND
DIST Z1 OP and/or PHS DIST Z1 OP operands.
At this moment the request to trip is placed for the trip output. As the fault is recognized as an AG fault, the TRIP PHASE A
operand is asserted by the trip output. This signal is passed to the breaker control scheme and results in tripping pole A of
the breaker.
Simultaneously with the TRIP PHASE A operand, the TRIP 1-POLE operand is asserted. This operand activates the open pole
detector. The latter detector responds to the TRIP PHASE A signal by declaring phase A open by asserting OPEN POLE OP
8 A (even before it is actually opened). The TRIP PHASE A signal resets only after the breaker actually operates as indicated
by its auxiliary contact. At this moment the open pole detector responds to the breaker position and continues to indicate
phase A opened. This indication results in establishing blocking signals for distance elements (OPEN POLE BLK AB, OPEN
POLE BLK CA operands are asserted). If neutral and negative-sequence overcurrent elements are mapped into the trip out-
put to trigger single-pole tripping, they must be blocked with the OPEN POLE BLK N operand, specifically provided for this
purpose. The OPEN POLE BLK N operand must be assigned through the block setting of the overcurrent element. The two
latter operands block phase distance AB and CA elements, respectively (all zones); the OPEN POLE A OP blocks the
ground distance AG elements (all zones). As a result, the Z1 OP and Z2 PKP operands that were picked-up reset immedi-
ately. The following distance elements remain operational guarding the line against evolving faults: BG, CG and BC.
As zone 2 and/or negative-sequence directional elements pick up due to the fault, the permission to trip is keyed to the
remote end. Assume here that a single-bit channel is used. If so, no extra information is sent to the remote end, just permis-
sion to trip sent over the TX1 operand. Upon receiving permission to trip over RX1, the POTT scheme decides to trip. The
scheme will check the phase selector for phase type identification and will issue a trip for phase A by asserting the POTT
TRIP A operand. This operand is passed to the trip output and results in exactly same action as described above for zone 1.

Depending on response times, the actual trip is initiated either by zone 1 or by the POTT scheme. At the moment TRIP 1-
POLE operand is asserted, the phase selector resets and no other trip action could take place. After the trip command is
issued all the picked up elements are forced to reset by the open pole detector.
The TRIP 1-POLE operand initiates automatically a single-pole autoreclose. The autoreclose is started and asserts the AR
RIP operand. This operand keeps blocking the phase selector so that it does not respond to any subsequent events. At the
same time the operand removes zero-sequence directional supervision from ground distance zones 2 and 3 so that they
could respond to a single-line-to-ground fault during open pole conditions.
The AR FORCE 3-P TRIP operand is asserted 1.25 cycles following autoreclose initiation. This operand acts as an enabler
for any existing trip request. In this case none of the protection elements is picked up at this time, therefore no more trips
are initiated.
When the recloser dead time interval is complete it signals the breaker control element to close the breaker. The breaker
control element operates output relays to close the breaker.
When pole A of the breaker closes this new status is reported to the breaker control element, which transfers this data to
the breaker failure, autorecloser, open pole detector and trip output elements. The response at breaker failure is dependent
on the programming of that element. The response at the autorecloser is not relevant to this discussion. At the open pole
detector, the blocking signals to protection elements are de-asserted.
If the fault was transient the reset time would expire at the autorecloser and the AR FORCE 3-P TRIP and RIP outputs would
be de-asserted, returning all features to the state described at the beginning of this description.
If the fault was permanent appropriate protection elements would detect it and place a trip request for the trip output ele-
ment. As the AR FORCE 3-P TRIP is still asserted, the request is executed as a three-pole trip.
The response of the system from this point is as described above for the second trip, except the autorecloser will go to lock-
out upon the next initiation (depending on the number of shots programmed).
c) SLG FAULT EVOLVING INTO LLG

When an AG fault occurs the events unfold initially as in the previous example. If the fault evolves quickly, the phase selec-
tor will change its initial assessment from AG to ABG fault and when the trip request is placed either by the zone 1 or the
POTT scheme, a three-pole trip will be initiated. If this is the case, all three TRIP PHASE A, B and C operands will be
asserted. The command is passed to the breaker control element and results in a three-pole trip. At the same time the
recloser is initiated as per settings of the trip output. As the TRIP 3-POLE operand is asserted (not the TRIP 1-POLE operand)
the open pole is not activated. Because the AR RIP in progress is asserted, the phase selector is blocked as well.
If the fault evolves slowly, the sequence is different: The relay trips phase A as in the previous example. The phase selector
resets, the open pole detector is activated and forces the zone 1 and zone 2 AG, AB, CA and negative-sequence overcur-
rent elements to reset. If the zone 1 BG element picks up, or the zone 2 BG element picks up resulting in operation of the
POTT scheme, no trip command will be issued until the AR FORCE 3-P TRIP is asserted. This happens 1.25 cycles after the
first trip. If at this time or any time later a request for trip is placed (due to an evolving fault), a three-pole trip is initiated. The
TRIP 1-POLE operand is de-asserted by the TRIP 3-POLE operand, resetting the open pole detector. Shortly all three-poles
are opened.
When the dead time expires, the recloser signals the breaker control to close the breaker. At this time all the protection ele-
ments are operational, as the open pole detector is not blocking any elements. If the line-side VTs are used, the line pickup
element is armed as well. If there is a fault on the line, these elements will pickup the fault and issue next request for trip.
This request results in three-pole trip as the AR FORCE 3-P TRIP is still asserted. 8
The response of the system from this point is as described above for the second trip, except the recloser will go to lockout
upon the next initiation (depending on the number of shots programmed).

8.5.2 PHASE SELECTION
The D60 uses phase relations between current symmetrical components for phase selection. First, the algorithm validates
if there is enough zero-sequence, positive-sequence, and negative-sequence currents for reliable analysis. The compari-
son is adaptive; that is, the magnitudes of the three symmetrical components used mutually as restraints confirm if a given
component is large enough to be used for phase selection. Once the current magnitudes are validated, the algorithm ana-
lyzes phase relations between the negative-sequence and positive-sequence currents and negative-sequence and zero-
sequence currents (when applicable) as illustrated below.
AB, CG,
BG ABG ABG
AG,
I2F AG I2F BCG
BC,
BCG
I1F I0F
CG CA, BG,
CAG CAG 837725A1.CDR
Figure 8–10: PHASE SELECTION PRINCIPLE (ABC PHASE ROTATION)

Due to dual comparisons, the algorithm is very secure. For increased accuracy and to facilitate operation in weak systems,
the pre-fault components are removed from the analyzed currents. The algorithm is very fast and ensures proper phase
selection before any of the correctly set protection elements operates.
Under unusual circumstances such as weak-infeed conditions with the zero-sequence current dominating during any
ground fault, or during cross-country faults, the current-based phase selector may not recognize any of the known fault pat-
tern. If this is the case, voltages are used for phase selection. The voltage algorithm is the same as the current-based algo-
rithm; for example, phase angles between the zero-sequence, negative-sequence, and positive-sequence voltages are
used. The pre-fault values are subtracted prior to any calculations.
The pre-fault quantities are captured and the calculations start when the disturbance detector (50DD) operates. When an
open pole is declared, the phase selector resets all its outputs operands and ignores any subsequent operations of the dis-
turbance detector.
The phase selector runs continuously. When there is no disturbance in the power system, and the disturbance detector
(50DD) from the source assigned as the DISTANCE SOURCE is reset, then the PHASE SELECT VOID FlexLogic operand is set
and all other phase selector operands are reset. All current and voltage sequence components are memorized and contin-
uously updated.
When the disturbance detector (50DD) operates, memory stops being updated and retains two cycles of old current and
voltage values. First, purely fault components of current and voltage are calculated by removing the pre-fault (memory)
quantities from presently calculated values. A series of conditions are checked with respect to magnitudes and phase
angles of current and voltage symmetrical components in order to detect the fault type. Secondly, currents are used to iden-
8 tify the fault type (AG, BG, CG, AB, BC, CA, ABG, BCG or CAG) according to the Phase selection principle figure above. If
the currents fail to identify the fault type, and voltages are available, then voltages are used. If any of the above types is
determined, then the corresponding FlexLogic operand below is asserted.

OPERAND DESCRIPTION
PHASE SELECT AG Asserted when a phase A to ground fault is detected.
PHASE SELECT BG Asserted when a phase B to ground fault is detected.
PHASE SELECT CG Asserted when a phase C to ground fault is detected.
PHASE SELECT AB Asserted when a phase A to B fault is detected.
PHASE SELECT BC Asserted when a phase B to C fault is detected.
PHASE SELECT CA Asserted when a phase C to A fault is detected.
PHASE SELECT ABG Asserted when a phase A to B to ground fault is detected.
PHASE SELECT BCG Asserted when a phase B to C to ground fault is detected.
PHASE SELECT CAG Asserted when a phase C to A to ground fault is detected.
If none of the fault types indicated above is determined, then three-phase fault conditions are checked to detect the pres-
ence of positive-sequence current and the absence of both zero-sequence and negative-sequence current. If these condi-
tions are met, then the PHASE SELECT 3P FlexLogic operand is asserted; otherwise, the PHASE SELECT VOID operand is
asserted, indicating that the phase selector failed to identify the fault type.
Finally, the states of the following additional FlexLogic operands are determined.
OPERAND DESCRIPTION
PHASE SELECT SLG Asserted if any of PHASE SELECT AG, PHASE SELECT BG, or PHASE SELECT CG
operands is active.
PHASE SELECT MULTI-P Asserted if neither the PHASE SELECT SLG nor PHASE SELECT VOID operands are being
asserted.
The phase selector operands are reset ½ cycle after the OPEN POLE OP FlexLogic operand is asserted or 500 ms after the
disturbance detector (50DD) initially operated. In the reset state, all phase selector FlexLogic operands are reset until reset
conditions are removed and the phase selector is ready for the next operation.
DELAY
FLEXLOGIC OPERAND
0.5 cycles
OPEN POLE OP RESET
0
DELAY
0 DELAY FLEXLOGIC OPERANDS
4 cycles 0 PHASE SELECT AG
FLEXLOGIC OPERAND AND START
500 ms PHASE SELECT BG
SRCn 50DD OP
PHASE SELECT CG
PHASE SELECT AB
FLEXLOGIC OPERAND
PHASE SELECTOR
PHASE SELECT BC
SRCn VT FUSE FAIL OP
PHASE SELECT CA
PHASE SELECT ABG
SETTING
PHASE SELECT BCG
DISTANCE SOURCE: PHASE SELECT CAG
PHASE SELECT 3P
I_0
8
PHASE SELECT SLG
I_1
PHASE SELECT MULTI-P
I_2
PHASE SELECT VOID
V_0
V_1
V_2
837027A5.CDR
Figure 8–11: PHASE SELECTOR LOGIC
8.5.3 COMMUNICATIONS CHANNELS FOR PILOT-AIDED SCHEMES
a) DESCRIPTION
In the D60 relay pilot-aided schemes transmit a code representing the type of fault determined by the local phase selector
according to the scheme logic. At a receiving terminal the local and remote data is combined to determine the action to be
performed. Schemes can be used with channels that can carry one, two or four bits. Using a one-bit channel, the schemes
at all terminals of the line use their local phase selectors to identify the fault type and initiate appropriate tripping actions. In

single pole operation applications however, a three-pole trip can be performed in the event of an in-line single-phase fault
co-incident with a fault on a different phase (cross-country fault) that is within the reach of the local phase selector, which is
considerably longer than the line. This possibility can be reduced by using a two-bit channel, and eliminated by using a
four-bit channel.
Using two-bit channels, the relays can share limited information about their local phase selection, improving considerably
the accuracy of single-pole tripping on cross-country faults. Two-bit channels however can only provide four different mes-
sages, one of which must be “no fault has been detected.” With only three messages available it is not possible to transmit
sufficient information to eliminate the use of local phase selector data, so a three-pole operation can occur in a cross-coun-
try fault condition. Using four-bit channels, the relays share enough information about fault types seen from all the line ter-
minals that local fault selector data can be rejected. In addition, in multiple bit systems the relays do not respond to non-
valid bit combinations, making the protection system more immune to communication problems than in a single bit system.
Each scheme within the relay has a setting that specifies the number of bits available on the associated communications
channel. This setting defines the input (RX1, RX2, RX3, RX4) and output (TX1, TX2, TX3, TX4 for communications and
[Scheme Abbreviation] TRIP A, TRIP B, TRIP C, TRIP 3P for action) operands used by the scheme, the data codes used to
convey fault data between terminals, and the method of combining information from the local and remote terminals to pro-
duce an output.
b) SINGLE BIT CHANNELS

The TX1 and RX1 operands are used, and fault data is coded per the following tables.
Table 8–11: PERMISSIVE SCHEME TRANSMIT CODES FOR 1-BIT CHANNELS

PHASE SELECTOR DETERMINATION OF BIT PATTERN TRANSMITTED
FAULT TYPE
TX1
AG, BC, BCG, BG, CA, CAG, CG, AB, ABG, 3P 1
Unrecognized or AR FORCE 3P TRIP 1
None of the above 0
Table 8–12: BLOCKING SCHEME TRANSMIT CODES FOR 1-BIT CHANNELS

FAULT TYPE
TX1
Unrecognized or AR FORCE 3P TRIP 0
None of the above 1
Table 8–13: UNBLOCKING SCHEME TRANSMIT CODES FOR 1-BIT CHANNELS

FAULT TYPE
TX1
8 Unrecognized or AR FORCE 3P TRIP 1
None of the above 0
The action output is generated per the following tables.
Table 8–14: PERMISSIVE SCHEME TRIP TABLE FOR 1-BIT CHANNELS

REMOTE DATA LOCAL DATA
BIT PATTERN RECEIVED REMOTE DETERMINATION LOCAL DETERMINATION OF TRIP OUTPUT
OF FAULT TYPE FAULT TYPE
RX1
1 Any AG Fault Trip Phase A (A+N/G)
1 Any BG Fault Trip Phase B (B+N/G)
1 Any CG Fault Trip Phase C (C+N/G)


RX1
1 Any AB, ABG, BC, BCG, CA, CAG, Trip Three Phases (per local
3P, Unrecognized selection, unrecognized and
3P=A+B+C+N/G)
Table 8–15: BLOCKING SCHEME TRIP TABLE FOR 1-BIT CHANNELS

RX1
0 Any AG Fault Trip Phase A
0 Any BG Fault Trip Phase B
0 Any CG Fault Trip Phase C
0 Any AB, ABG, BC, BCG, CA, CAG, Trip Three Phases
3P, Unrecognized
Table 8–16: UNBLOCKING SCHEME TRIP TABLE FOR 1-BIT CHANNELS

RX1 LOG1
0 or 1 1 Any AG Fault DCUB TRIP A
0 or 1 1 Any BG Fault DCUB TRIP B
0 or 1 1 Any CG Fault DCUB TRIP C
0 or 1 1 Any AB, ABG, BC, BCG, CA, CAG, DCUB TRIP 3P
3P, Unrecognized
The scheme initiates a three-phase trip if the phase selector fails to recognize the fault type or after the AR FORCE 3P
TRIP operand is asserted.
c) TWO-BIT CHANNELS
The TX1, TX2, RX1 and RX2 operands are used and fault data is coded per the following tables.

PHASE SELECTOR DETERMINATION BIT PATTERN TRANSMITTED
OF FAULT TYPE
TX1 TX2
AG, BC, BCG 1 0
BG, CA, CAG
CG, AB, ABG, 3P, Unrecognized
0
1
1
1
8

PHASE SELECTOR DETERMINATION BIT PATTERN TRANSMITTED FLEXLOGIC™ OPERANDS
OF FAULT TYPE ASSERTED
TX1 TX2 TX1 STOP TX2 STOP
AG, BC, BCG 0 1 1 0
BG, CA, CAG 1 0 0 1
CG, AB, ABG, 3P 0 0 1 1
CG, AB, ABG, 3P, Unrecognized 0 0 1 1


PHASE SELECTOR DETERMINATION BIT PATTERN TRANSMITTED
OF FAULT TYPE
TX1 TX2
AG, BC, BCG 1 0
BG, CA, CAG 0 1
CG, AB, ABG, 3P, Unrecognized 1 1

BIT PATTERN RECEIVED REMOTE DETERMINATION OF FAULT LOCAL DETERMINATION TRIP OUTPUT
TYPE OF FAULT TYPE
RX1 RX2
1 0 AG, BC, BCG AG, AB, ABG CA, CAG, 3P Trip Phase A
0 1 BG, CA, CAG AG
1 1 CG, AB, ABG, 3P, Unrecognized AG
0 1 BG, CA, CAG BG, AB, ABG, BC, BCG, 3P Trip Phase B
1 1 CG, AB, ABG, 3P, Unrecognized BG
1 0 AG, BC, BCG BG
1 1 CG, AB, ABG, 3P, Unrecognized CG, BC, BCG, CA, CAG Trip Phase C
1 0 AG, BC, BCG CG
0 1 BG, CA, CAG CG
1 1 CG, AB, ABG, 3P, Unrecognized AB, ABG, 3P, Unrecognized Trip Three Phases
1 0 AG, BC, BCG BC, BCG, Unrecognized
0 1 BG, CA, CAG CA, CAG, Unrecognized
Table 8–21: BLOCKING SCHEME TRIP TABLE FOR 2-BIT CHANNELS

BIT PATTERN RECEIVED REMOTE DETERMINATION OF FAULT LOCAL DETERMINATION TRIP OUTPUT
TYPE OF FAULT TYPE
RX1 RX2
0 1 AG, BC, BCG AG, AB, ABG CA, CAG, 3P DIR BLOCK TRIP A
1 0 BG, CA, CAG AG
0 0 CG, AB, ABG, 3P, Unrecognized AG
1 0 BG, CA, CAG BG, AB, ABG, BC, BCG, 3P DIR BLOCK TRIP B
0 0 CG, AB, ABG, 3P, Unrecognized BG
0 1 AG, BC, BCG BG
8 0
0
0
1
CG, AB, ABG, 3P, Unrecognized
AG, BC, BCG
CG, BC, BCG, CA, CAG
CG
DIR BLOCK TRIP C
1 0 BG, CA, CAG CG

0 0 CG, AB, ABG, 3P, Unrecognized AB, ABG, 3P, Unrecognized DIR BLOCK TRIP 3P
0 1 AG, BC, BCG BC, BCG Unrecognized
1 0 BG, CA, CAG CA, CAG Unrecognized

Table 8–22: UNBLOCKING SCHEME TRIP TABLE FOR 2-BIT CHANNELS

BIT PATTERN RECEIVED REMOTE DETERMINATION OF LOCAL DETERMINATION TRIP OUTPUT
FAULT TYPE OF FAULT TYPE
RX1 LOG1 RX2 LOG2
1 1 0 0 AG, BC, BCG AG, AB, ABG CA, CAG, 3P DCUB TRIP A
0 1 0 0
0 0 1 1 BG, CA, CAG AG
0 0 0 1
1 1 1 1 CG, AB, ABG, 3P, unrecognized AG
0 1 1 1
1 1 0 1
0 1 0 1
0 0 1 1 BG, CA, CAG BG, AB, ABG BC, BCG, 3P DCUB TRIP B
0 0 0 1
1 1 1 1 CG, AB, ABG, 3P, unrecognized BG
0 1 1 1
1 1 0 1
0 1 0 1
1 1 0 0 AG, BC, BCG BG
0 1 0 0
1 1 0 0 AG, BC, BCG CG DCUB TRIP C
0 1 0 0
0 0 1 1 BG, CA, CAG CG
0 0 0 1
1 1 1 1 CG, AB, ABG, 3P, unrecognized CG, BC, BCG, CA, CAG
0 1 1 1
1 1 0 1
0 1 0 1
1 1 0 0 AG, BC, BCG BC, BCG, unrecognized DCUB TRIP 3P
0 1 0 0
0 0 1 1 BG, CA, CAG CA, CAG, unrecognized
0 0 0 1
1 1 1 1 CG, AB, ABG, 3P, unrecognized AB, ABG, 3P, unrecognized
0 1 1 1
1 1 0 1
0 1 0 1
d) FOUR-BIT CHANNELS 8
The TX1, TX2, TX3, TX4, RX1, RX2, RX3 and RX4 operands are used.

PHASE SELECTOR BIT PATTERN TRANSMITTED
DETERMINATION OF FAULT TYPE
TX1 TX2 TX3 TX4
AG 1 0 0 0
BG 0 1 0 0
CG 0 0 1 0
AB, ABG, BC, BCG, CA, CAG, 3P, 0 0 0 1
Unrecognized


PHASE SELECTOR BIT PATTERN TRANSMITTED FLEXLOGIC™ OPRERANDS ASSERTED
DETERMINATION OF FAULT
TYPE TX1 TX2 TX3 TX4 TX1 STOP TX2 STOP TX3 STOP TX4 STOP
AG 0 1 1 1 1 0 0 0
BG 1 0 1 1 0 1 0 0
CG 1 1 0 1 0 0 1 0
AB, ABG, BC, BCG, CA, CAG, 1 1 1 0 0 0 0 1
3P, Unrecognized

PHASE SELECTOR BIT PATTERN TRANSMITTED
TX1 TX2 TX3 TX4
AG 1 0 0 0
BG 0 1 0 0
CG 0 0 1 0
AB, ABG, BC, BCG, CA, CAG, 3P, 0 0 0 1
Unrecognized

BIT PATTERN RECEIVED REMOTE LOCAL DETERMINATION OF TRIP OUTPUT
RX1 RX2 RX3 RX4 FAULT TYPE
0 0 0 1 MULTI-P AG Trip Phase A
0 1 0 0 BG AG
0 0 1 0 CG AG
1 0 0 0 AG AG, AB, ABG, CA, CAG, 3P,
Unrecognized
0 1 0 0 BG BG, AB, ABG, BC, BCG, 3P, Trip Phase B
Unrecognized
1 0 0 0 AG BG
0 0 1 0 CG BG
0 0 0 1 MULTI-P BG
0 0 1 0 CG CG, BC, BCG, CA, CAG, 3P, Trip Phase C
Unrecognized
1 0 0 0 AG CG
0 1 0 0 BG CG
8 0 0 0 1 MULTI-P CG
1 0 0 0 AG BC, BCG Trip Three Phases
0 1 0 0 BG CA, CAG
0 0 1 0 CG AB, ABG
0 0 0 1 MULTI-P Unrecognized

Table 8–27: BLOCKING SCHEME TRIP TABLE FOR FOUR-BIT CHANNELS

BIT PATTERN RECEIVED REMOTE LOCAL DETERMINATION TRIP OUTPUT
RX1 RX2 RX3 RX4 OF FAULT TYPE
0 0 0 0 Any while the INIT Trip as for single-bit
signal was not channel
established
1 1 1 0 MULTI-P AG DIR BLOCK TRIP A
1 0 1 1 BG AG
1 1 0 1 CG AG
0 1 1 1 AG AG, AB, ABG, CA, CAG, 3P,
Unrecognized
1 0 1 1 BG BG, AB, ABG, BC, BCG, 3P, DIR BLOCK TRIP B
Unrecognized
0 1 1 1 AG BG
1 1 0 1 CG BG
1 1 1 0 MULTI-P BG
1 1 0 1 CG CG, BC, BCG, CA, CAG, 3P, DIR BLOCK TRIP C
Unrecognized
0 1 1 1 AG CG
1 0 1 1 BG CG
1 1 1 0 MULTI-P CG
0 1 1 1 AG BC, BCG DIR BLOCK TRIP 3P
1 0 1 1 BG CA, CAG
1 1 0 1 CG AB, ABG
1 1 1 0 MULTI-P Unrecognized

Table 8–28: UNBLOCKING SCHEME TRIP TABLE FOR FOUR-BIT CHANNELS

BIT PATTERN RECEIVED REMOTE LOCAL TRIP OUTPUT
DETERMINATION DETERMINATION OF
RX1 LOG1 RX2 LOG2 RX3 LOG3 RX4 LOG4 OF FAULT TYPE FAULT TYPE
0 0 0 0 0 0 1 1 MULTI-P AG DCUB TRIP A
0 0 0 0 0 0 0 1
0 0 1 1 0 0 0 0 BG
0 0 0 1 0 0 0 0
0 0 0 0 1 1 0 0 CG
0 0 0 0 0 1 0 0
1 1 0 0 0 0 0 0 AG AG, AB, ABG, CA,
CAG, 3P, unrecognized
0 1 0 0 0 0 0 0
0 0 1 1 0 0 0 0 BG AG, AB, ABG, CA, DCUB TRIP B
0 0 0 1 0 0 0 0
1 1 0 0 0 0 0 0 AG BG
0 1 0 0 0 0 0 0
0 0 0 0 1 1 0 0 CG
0 0 0 0 0 1 0 0
0 0 0 0 0 0 1 1 MULTI-P
0 0 0 0 0 0 0 1
0 0 0 0 1 1 0 0 CG CG, BC, BCG, CA, DCUB TRIP C
0 0 0 0 0 1 0 0
1 1 0 0 0 0 0 0 AG CG
0 1 0 0 0 0 0 0
0 0 1 1 0 0 0 0 BG
0 0 0 1 0 0 0 0
0 0 0 0 0 0 1 1 MULTI-P
0 0 0 0 0 0 0 1
1 1 0 0 0 0 0 0 AG BC, BCG DCUB TRIP 3P
0 1 0 0 0 0 0 0
0 0 1 1 0 0 0 0 BG CA, CAG
0 0 0 1 0 0 0 0
0 0 0 0 1 1 0 0 CG AB, ABG
0 0 0 0 0 1 0 0
0 0 0 0 0 0 1 1 MULTI-P 3P or unrecognized
0 0 0 0 0 0 0 1

8.5.4 PERMISSIVE ECHO SIGNALING
The “echo” feature can reduce the response time of an over-reaching scheme when a terminal is disconnected from the
line. In this condition, a zone 2 element at the terminal that remains in-service can detect a fault, but cannot trip, as a per-
missive signal is not received from the remote terminal. This feature is provided in the permissive over-reaching transfer trip
and hybrid permissive over-reaching transfer trip schemes.
PERMISSIVE OVER-REACHING TRANSFER TRIP SCHEME:
When used this feature will “echo” a reliable received permissive signal back to the originating terminal when a line-
end-open condition is identified by the line pickup logic. The permissive echo is programmed as a one-shot logic. The
echo is sent only once and then the echo logic locks out for a settable period. The duration of the echo pulse does not
depend on the duration or shape of the received Rx signals but is settable.
The echo is sent back only if none of the overreaching protection elements operates.
HYBRID PERMISSIVE OVER-REACHING TRANSFER TRIP PERMISSIVE ECHO:
When used this feature will “echo” a reliable received permissive signal back to the originating terminal if the line-end-
open condition is recognized by the line pickup scheme and the fault is not identified as a reverse fault by the zone 4 or
the ground directional overcurrent function (if used). The permissive echo is programmed as a one-shot logic. The
echo is sent only once and then the echo logic locks out for a settable period. The duration of the echo pulse does not
depend on the duration or shape of the received RX signal but is settable as ECHO DURATION.
The echo is sent back only if none of the overreaching protection elements operates.
PERMISSIVE ECHO OPERANDS AND TRANSMIT CODES:
In single-pole tripping, single-bit channel applications the signal received on bit no. 1 (Rx1) is echoed back on bit no. 1
(Tx1). In two- and four-bit applications the following echo tables apply.
Table 8–29: ECHO TABLE FOR 2-BIT CHANNELS

LOCAL DETERMINATION OF FAULT TYPE ECHOED BITS
TX1 TX2
AG 1 0
BG 0 1
CG 1 1
AB, ABG, BC, BCG, CA, CAG, 3P, Unrecognized Send back as received
Table 8–30: ECHO TABLE FOR 4-BIT CHANNELS

LOCAL DETERMINATION OF FAULT TYPE ECHOED BITS
TX1 TX2 TX3 TX4
AG 1 0 0 0
BG 0 1 0 0
CG 0 0 1 0
AB, ABG, BC, BCG, CA, CAG, 3P, Unrecognized Send back as received 8
For the directional comparison unblocking scheme, the echo is performed in the same manner as the Hybrid POTT
echo, but by applying additionally the following logic for both the Rx (received) and LOG (loss-of-guard) for each
NOTE channel: ECHON= LOGN AND RXN.

8.5.5 PILOT SCHEME / PHASE SELECTOR COORDINATION
For local fault type identification the pilot schemes use the Phase Selector. The latter may fail to respond to certain fault
scenarios. Examples are: simultaneous forward and reverse fault, simultaneous SLG and LL fault involving different phases
(e.g. AG and BC) or two simultaneous faults in the same direction but at very different locations. The Phase Selector is opti-
mized to either indicate correctly the forward fault or to assert the Void flag. For example, a combination of AG and BC is
not a valid fault type - it is two different simultaneous faults and as such cannot be described by any single fault pattern,
therefore, the Phase Selector would assert the Void flag.
The VOID phase selection combined with a local trip request (such as high-set directional overcurrent) will result in three-
pole trip as per the Trip Output logic.
The Pilot Schemes, however, try to recover more information from the distance elements. Each scheme uses a forward
looking, either underreaching or overreaching, distance zone. A given Pilot Scheme analyzes this zone for fault type identi-
fication if the Phase Selector asserts its Void flag: the DUTT scheme uses Z1; all the other schemes use Z2. The schemes
analyze all six fault loops of the zone to determine the fault type.
For example, simultaneous forward AG and reverse BG faults may result in the Void indication. The POTT scheme would
analyze the Z2 response. As only the AG element is picked up, the local phase selection is determined as AG. This is a cor-
rect indication.
Depending on the number of bits used for communications, the accuracy of the overall response will be further improved as
illustrated in the next subsection.
This enhanced operation of the pilot-aided schemes is the reason to use a short pilot scheme priority time when setting the
Trip Output logic. The timer will force the scheme to wait for a decision from the pilot scheme for a short period of time
before accepting any local trip request. The advantage, however, materializes only if more than one-bit communications
channels are used, and is important only on parallel lines or when the application requires maximum accuracy of single-
pole tripping. In other cases, it is not recommended to delay the local trip decision.

8.5.6 CROSS-COUNTRY FAULT EXAMPLE
Assume a single pole operation application where D60 relays are used to protect a two terminal line, (terminals T1 and T2)
using phase and ground distance zone 1, 2 and 3 elements in a permissive over-reaching transfer trip scheme. The perfor-
mance of the system with one- two and four-bit communications channels is outlined for a mid-line phase A-to-ground fault
and a co-incident phase B-to-ground fault just behind terminal T2. Assume also that the reclosers are enabled and reset.
At T1 the following protection elements will pickup:
• Ground Distance Zone 1, 2, and 3 for an AG fault
• Ground Distance Zone 2 and 3 for a BG fault
• Phase Distance Zone 2 and 3 for an AB fault
At T1 the phase selector will determine the fault is type ABG. This response is independent from the distance elements –
the Phase Selector sees two forward faults.
At T2 the following protection elements will pickup:
• Ground Distance Zone 1, 2, and 3 for an AG fault
At T2 the phase selector will determine the fault is type AG. The reverse BG fault is likely to be ignored.
If a one-bit channel is used, terminal T1 will trip three poles but terminal T2 will trip phase A only, (see the Tables below)
which is undesirable.
TERMINAL REMOTE DATA LOCAL DATA

BIT PATTERN RECEIVED REMOTE DETERMINATION LOCAL DETERMINATION TRIP OUTPUT
OF FAULT TYPE OF FAULT TYPE
RX1
T1 1 Any MULTI-P (ABG) Trip Three Phases
T2 1 Any AG Trip Phase A
If a two-bit channel is used both terminals will trip phase A only, (see the Tables below) which is the desired outcome.

RX1 RX2
T1 1 0 AG ABG Trip Phase A
T2 1 1 ABG AG Trip Phase A
If a four-bit channel is used both terminals will trip phase A only, (see the Tables below) which is the desired outcome.

T1
RX1
0
RX2
0
RX3
0
RX4
1 AG ABG Trip Phase A
8
T2 1 0 0 0 ABG AG Trip Phase A

8.6 FAULT LOCATOR 8 THEORY OF OPERATION
8.6FAULT LOCATOR 8.6.1 FAULT TYPE DETERMINATION
Fault type determination is required for calculation of fault location – the algorithm uses the angle between the negative and
positive sequence components of the relay currents. To improve accuracy and speed of operation, the fault components of
the currents are used; that is, the pre-fault phasors are subtracted from the measured current phasors. In addition to the
angle relationships, certain extra checks are performed on magnitudes of the negative and zero-sequence currents.
The single-ended fault location method assumes that the fault components of the currents supplied from the local (A) and
remote (B) systems are in phase. The figure below shows an equivalent system for fault location.
distance to fault
Remote
Local bus bus
ZA IA mZ (1-m)Z IB ZB
EA VF RF EB
VA VB
842780A1.CDR
Figure 8–12: EQUIVALENT SYSTEM FOR FAULT LOCATION

The following equations hold true for this equivalent system.
VA = m  Z  IA + RF   IA + IB  (EQ 8.7)
where: m = sought pu distance to fault, Z = positive sequence impedance of the line.

The currents from the local and remote systems can be parted between their fault (F) and pre-fault load (pre) components:
I A = I AF + I Apre (EQ 8.8)
and neglecting shunt parameters of the line:

I B = I BF – I Apre (EQ 8.9)
Inserting the IA and IB equations into the VA equation and solving for the fault resistance yields:
VA – m  Z  IA
R F = ----------------------------------- (EQ 8.10)
I BF
I AF   1 + --------
I AF
Assuming the fault components of the currents, IAF and IBF are in phase, and observing that the fault resistance, as imped-
ance, does not have any imaginary part gives:
VA – m  Z  IA
Im  ----------------------------------- = 0 (EQ 8.11)
 
8 I AF
where: Im() represents the imaginary part of a complex number. Solving the above equation for the unknown m creates the
following fault location algorithm:
Im  V A  I AF 
m = ---------------------------------------- (EQ 8.12)
Im  Z  I A  I AF 
where * denotes the complex conjugate and I AF = I A – I Apre .

Depending on the fault type, appropriate voltage and current signals are selected from the phase quantities before applying
the two equations above (the superscripts denote phases, the subscripts denote stations).
For AG faults:
A A
VA = VA , I A = I A + K 0  I 0A (EQ 8.13)

8 THEORY OF OPERATION 8.6 FAULT LOCATOR
For BG faults:
B B
VA = VA , I A = I A + K 0  I 0A (EQ 8.14)
For CG faults:
C BC
VA = VA , I A = I A + K 0  I 0A (EQ 8.15)
For AB and ABG faults:

A B A B
VA = VA – VA , IA = IA – IA (EQ 8.16)
For BC and BCG faults:

B C B C
VA = VA – VA , IA = IA – IA (EQ 8.17)
For CA and CAG faults:

C A C A
VA = VA – VA , IA = IA – IA (EQ 8.18)
where K0 is the zero sequence compensation factor (for the first six equations above)
For ABC faults, all three AB, BC, and CA loops are analyzed and the final result is selected based upon consistency of the
results
The element calculates the distance to the fault (with m in miles or kilometers) and the phases involved in the fault.
The relay allows locating faults from delta-connected VTs. If the FAULT REPORT 1 VT SUBSTITUTION setting is set to “None”,
and the VTs are connected in wye, the fault location is performed based on the actual phase to ground voltages. If the VTs
are connected in delta, fault location is suspended.
If the FAULT REPORT 1 VT SUBSTITUTION setting value is “V0” and the VTs are connected in a wye configuration, the fault
location is performed based on the actual phase to ground voltages. If the VTs are connected in a delta configuration, fault
location is performed based on the delta voltages and externally supplied neutral voltage:
1
V A = ---  V N + V AB – V CA 
3
1
V B = ---  V N + V BC – V AB  (EQ 8.19)
3
1
V B = ---  V N + V CA – V BC 
3
If the FAULT REPORT 1 VT SUBSTITUTION setting value is “I0” and the VTs are connected in a wye configuration, the fault loca-
tion is performed based on the actual phase to ground voltages. If the VTs are connected in a delta configuration, fault loca-
tion is performed based on the delta voltages and zero-sequence voltage approximated based on the zero-sequence
current:
1
V A = ---  V AB – V CA  – Z SYS0 I 0
3
1
V B = ---  V BC – V AB  – Z SYS0 I 0 (EQ 8.20)
8
3
1
V B = ---  V CA – V BC  – Z SYS0 I 0
3
where ZSYS0 is the equivalent zero-sequence impedance behind the relay as entered under the fault report setting menu.

8.6 FAULT LOCATOR 8 THEORY OF OPERATION
SETTINGS
FAULT REPORT 1 Z1
MAG:
FAULT REPORT 1 Z1
ANGLE:
FAULT REPORT 1 Z0
MAG:
FAULT REPORT 1 Z0
ANGLE:
FAULT REPORT 1
LENGTH UNITS:
FAULT REPORT 1
LENGTH:
SETTING FAULT REPORT 1 VT

SUBSTITUTION:
FAULT REPORT
TRIG: FAULT REP 1
SYSTEM Z0 MAG:
Off=0
FAULT REP 1
SYSTEM Z0 ANGLE:
SETTINGS
AND RUN
FAULT REPORT
SOURCE: ACTUAL VALUES
0 FAULT REPORT #
SRC X 50DD OP
3 SEC
IA DATE
IB TIME
IC FAULT TYPE
FAULT
3I_0 LOCATOR 1 FAULT LOCATION
VA or VAB FAULT# RECLOSE SHOT
VB or VBC
VC or VCA
Vn or V_0
SHOT # FROM
AUTO RECLOSURE 827094A5.CDR
Figure 8–13: FAULT LOCATOR SCHEME

9 APPLICATION OF SETTINGS 9.1 APPLICATION GUIDELINES
9 APPLICATION OF SETTINGS 9.1APPLICATION GUIDELINES 9.1.1 INTRODUCTION
This chapter provides general application guidelines for stepped distance, overcurrent and pilot protection. Where relevant,
design details and performance characteristics of the D60 are given to facilitate the process of setting the relay for a given
application.
9.1.2 IMPACT OF MEMORY POLARIZATION
As explained in Chapter 8, the D60 uses a memorized positive sequence voltage as a polarizing signal in order to achieve
dependable operation for forward faults and secure non-operation for reverse faults.
The dynamic shift of the characteristic ensures improved directionality, but it also means that if a backup function is
required for a reverse fault on the bus, then it is appropriate to reverse Zone 4 so that a time delayed backup function may
be obtained. As mentioned earlier, it may be beneficial to also avoid extremely large reach settings by setting a remote
backup so that it is reverse looking. This strategy can be beneficial if the reduced reach enhances the discrimination
between the load and fault conditions.
9.1.3 HIGH-SET OVERCURRENT ELEMENTS
Especially at low SIR values, fast fault clearance times may be seen as extremely important, both from system stability, and
from equipment damage viewpoints. The high-set overcurrent element, when set appropriately, can be extremely useful in
achieving these goals. It helps the setting calculations if the system impedances are reasonably well known.
The overcurrent pick up should be set to the greater of the following values:
1. The maximum infeed seen by the relay, for a close in reverse fault.
2. The maximum fault level seen by the relay for a fault at 100% of the protected line.
The maximum error of the phase overcurrent elements is below 2%. A safety factor of 1.25 should be used to account for
relay errors and system impedance uncertainty.
If CT saturation is an issue such as close to a generation where long lasting dc components are likely to saturate the CTs, it
should be noted that the instantaneous overcurrent elements require 1.33 cycle of data to operate for a multiple of pickup of
1.01. For higher multiples of pickup, the relation between the multiple of pickup and the amount of data required for opera-
tion before complete CT saturation is approximately linear. For example, for a multiple of pickup of 4, approximately 1.33 /
4 = 0.332 of power cycle is required by the phase instantaneous overcurrent element to operate. The above information
should not be confused with the operating time, which includes some inherent delays such as a trip rated output contact.

9.2 DISTANCE ELEMENTS (STEPPED DISTANCE SCHEME) 9 APPLICATION OF SETTINGS
9.2DISTANCE ELEMENTS (STEPPED DISTANCE SCHEME) 9.2.1 PHASE DISTANCE
a) PHASE CURRENT SUPERVISION AND FUSE FAILURE

The phase-to-phase (delta) current is used to supervise the phase distance elements, primarily to ensure that in a de-ener-
gized state the distance elements will not be picked up due to noise or induced voltages, on the line.
However, this supervision feature may also be employed to prevent operation under fuse failure conditions. This obviously
requires that the setting must be above maximum load current and less than the minimum fault conditions for which opera-
tion is expected. This potential problem may be avoided by the use of a separate fuse fail function, which means that the
phase current supervision can be set much lower, typically two times the capacitance charging current of the line.
The usage of the fuse fail function is also important during double-contingency events such as an external fault during fuse
fail conditions. The current supervision alone would not prevent maloperation in such circumstances.
It must be kept in mind that the fuse failure element provided on the D60 needs some time to detect fuse fail conditions.
This may create a race between the instantaneous zone 1 and the fuse failure element. Therefore, for maximum security, it
is recommended to both set the current supervision above the maximum load current and use the fuse failure function. The
current supervision prevents maloperation immediately after the fuse fail condition giving some time for the fuse failure ele-
ment to take over and block the distance elements permanently. This is of a secondary importance for time-delayed zones
2 and up as the fuse failure element has some extra time for guaranteed operation. The current supervision may be set
below the maximum load current for the time delayed zones.
Blocking distance elements during fuse fail conditions may not be acceptable in some applications and/or under some pro-
tection philosophies. Applied solutions may vary from not using the fuse failure element for blocking at all; through using it
and modifying – through FlexLogic and multiple setting groups mechanisms – other protection functions or other relays to
provide some protection after detecting fuse fail conditions and blocking the distance elements; to using it and accepting
the fact that the distance protection will not respond to subsequent internal faults until the problem is addressed.
To be fully operational, the Fuse Failure element must be enabled, and its output FlexLogic operand must be indi-
cated as the blocking signal for the selected protection elements.
NOTE
For convenience, the current supervision threshold incorporates the 3 factor.
b) PHASE DISTANCE ZONE 1

As typically used for direct tripping, the zone 1 reach must be chosen so that it does not extend beyond the far end(s) of the
protected line. Zone 1 provides nominally instantaneous protection for any phase fault within a pre-determined distance
from the relay location. To ensure that no overreach occurs, typically requires a setting of 80 to 90% of the line length,
which covers CT and VT errors, relay inaccuracy and transient overreach as well as uncertainty in the line impedance for
each phase, although transposition may minimize this latter concern.
The total relay inaccuracy including both steady state and transient overreach even when supplied from CVTs under the
source impedance ratios of up to 30, is below 5%.
c) PHASE DISTANCE ZONE 2

Zone 2 is an overreaching element, which essentially covers the final 10 to 20% whole of the line length with a time delay.
The additional function for the zone 2 is as a timed backup for faults on the remote bus. Typically the reach is set to 125%
of the positive-sequence impedance of the line, to ensure operation, with an adequate margin, for a fault at 100% of the line
length. The necessary time delay must ensure that coordination is achieved with the clearance of a close-in fault on the
next line section, including the breaker operating time.
The zone 2 time delay is typically set from 0.2 to 0.6 seconds, although this may have to be reviewed more carefully if a
short line terminates on the remote bus, since the two zone 2 elements may overlap and therefore not coordinate in a sat-
isfactory manner.
9 d) PHASE DISTANCE ZONE 3
If a remote backup philosophy is followed, then the reach of this element must be set to account for any infeed at the
remote bus, plus the impedance of the longest line which terminates on this remote bus. The time delay must coordinate
with other time-delayed protections on any remote line. Circuit loading limitations created by a long zone reach may be
overcome by using lens or quadrilateral characteristics and/or a load encroachment supervising characteristic. Consider-

9 APPLICATION OF SETTINGS 9.2 DISTANCE ELEMENTS (STEPPED DISTANCE SCHEME)
ation should also be given to a situation where the load impedance may enter into the relay characteristic for a time longer
than the chosen time delay, which could occur transiently during a system power swing. For this reason the power swing
blocking function should be used.
e) PHASE DISTANCE ZONE 4

A further contribution to remote backup, the reach of this element must be set to account for any infeed at the remote bus.
The time delay must coordinate with other time-delayed protections on the next line. The use of a lens characteristic or the
load encroachment element may be advantageous if load limits are a problem.
To avoid extremely large reach settings, the D60 has the ability to implement any element so that it is reverse looking,
which then can provide a back up for the longest line terminated on the local bus. This strategy can be beneficial if the
reduced reach helps discrimination between the load and fault conditions, but must be implemented at both ends of the
protected line.
f) PHASE DISTANCE ZONE 5

An additional fifth phase distance zone can be used in special applications. This zone may be start zone for arming tripping
from all other zones, in both forward and reverse directions of the of protected line. This zone may also be used as an addi-
tional reverse-looking zone for implementation of two reverse-looking zones, thus providing two zone backup reverse-look-
ing protection. The fifth distance zone can be used as an alarm zone, indicating that load impedance is approaching the
zone characteristic.
9.2.2 GROUND DISTANCE
a) NEUTRAL CURRENT SUPERVISION

The current supervision for the ground distance elements responds to an internally calculated neutral current (3 × I_0). The
setting for this element should be based on twice the zero-sequence line capacitance current or the maximum zero-
sequence unbalance under maximum load conditions. This element should not be used to prevent an output when the load
impedance is inside the distance characteristic on a steady state basis.
b) POLARIZING CURRENT AND NON-HOMOGENEITY CORRECTION ANGLE OF THE QUAD CHARACTERISTIC

An ideal reactance line for single-line-to-ground faults is polarized from the fault current flowing through the fault resistance.
Such a line defines constant reach and could be implemented by the following angle comparator:
I  Z – V vs. j  I F (EQ 9.1)
The relay could only approximate the unknown fault current by the zero-sequence or the negative-sequence currents mea-
sured at the relaying point. Depending on system parameters, either the zero-sequence or the negative-sequence current
presents better approximation of the fault current angle.
Given the equivalent systems shown in the figure below, the angular difference between the zero-sequence or negative-
sequence currents at the relay, and the fault current can be calculated as follows:
IF Z 0A + Z 0L + Z 0B
 0 = angle  ---------------------- = angle  ------------------------------------------- (EQ 9.2)
I 0_RELAY Z 0B +  1 – d Z 0L
IF Z 1A + Z 1L + Z 1B
 2 = angle  ---------------------- = angle  ------------------------------------------- (EQ 9.3)
I 2_RELAY Z 1B +  1 – d Z 1L
where: A is the local equivalent system

B is the remote equivalent system
L is the line
d is the per-unit (pu) intended reach of the zone (typically 0.7 to 0.9). 9

9.2 DISTANCE ELEMENTS (STEPPED DISTANCE SCHEME) 9 APPLICATION OF SETTINGS
IF
Z0A dZ0L (1 – d)Z0L Z0B
I0
I0
IF
I2
DEPENDING ON SYSTEM
Z1A dZ1L (1 – d)Z1L Z1B PARAMETERS, I0 OR I2 MAYBE A
BETTER APPROXIMATION OF THE
FAULT CURRENT ANGLE
I2
IF
842742A1.CDR
Figure 9–1: UNDERSTANDING SYSTEM HOMOGENEITY

If abs   0   abs   2  , the zero-sequence network is more homogenous (the zero-sequence current better approximates
the fault current), and zero-sequence polarizing should be selected. Otherwise, negative-sequence is a better polarizing
signal.
The calculated  angles reflect errors between the ideal and applied polarizing angles. Therefore, after selecting the polar-
izing current, the corresponding angle should be chosen as the non-homogeneity correction angle. For example, calcula-
tions yielding 0 = 5° and 2 = –1° should result in selecting the negative-sequence for polarization, and the value of –1°
for non-homogeneity correction.
Quite often the non-homogeneity correction angle is used to apply extra security rather than correct the angle between the
relay and the fault currents. For extra security the angle should be set to negative values.
Ability to select an optimum polarizing signal and to correct for non-homogeneity should be approached with care. The best
polarizing signal and the correcting angle both depend on system parameters and intended reach of the zone. If the system
configuration is static, the selection is straightforward.
However, if the system configuration may change significantly, all the relevant system topologies shall be considered for
calculations. Either a compromise choice is made, or different settings are applied via switchable setting groups depending
on system conditions. In highly non-homogenous and dynamic systems where the correction for non-homogeneity is not
feasible, conservative reach (reduced) and/or correction angle (negative) settings should be considered.
c) GROUND DISTANCE ZONE 1

The zone 1 reach must be set so that nominally instantaneous operation does not extend beyond the end of the protected
line. However this may be somewhat more complicated than for the phase elements, because of zero sequence mutual
induction with an adjacent parallel line, possibly carried on the same tower, which can be out of service and grounded at
multiple points. A fault beyond 100% of the protected line may cause overreach unless the reach is reduced significantly,
sometimes as low as 65% of the line length. If the line being protected does not have a significant interaction with an adja-
cent circuit, then the typical 80% setting may be used. If there is significant mutual coupling between the parallel lines, then
9 the mutual compensation feature of the ground distance elements can be used instead of a drastic reduction in the reach.
However, even in this case, there is more uncertainty as compared with the phase distance elements because the zero-
sequence impedance of the line and thus the zero-sequence-compensating factors may vary significantly due to weather
and other conditions.

9 APPLICATION OF SETTINGS 9.2 DISTANCE ELEMENTS (STEPPED DISTANCE SCHEME)
d) GROUND DISTANCE ZONE 2

To ensure that the zone 2 can see 100% of the line, inter-circuit mutual effects must be considered, as they can contribute
to a significant under-reach. Typically this may occur on double circuit lines, when both lines may carry the same current.
An analytical study should be carried out to determine the appropriate reach setting.
The main purpose of this element is to operate for faults beyond the reach of the local zone 1 element, and therefore a time
delay must be used similar to the phase fault case.
e) GROUND DISTANCE ZONE 3

This remote back up function must have a reach which is set to account for any infeed at the remote bus, plus the imped-
ance of the longest line which terminates on this remote bus. Similar to the phase fault case, a zone 3 element must be
time coordinated with timed clearances on the next section.
f) GROUND DISTANCE ZONE 4

As a further contribution to a remote backup philosophy, the reach of this element must be set to account for any infeed at
the remote bus. The time delay must coordinate with other time-delayed protections on the next line. The use of a lens
characteristic or load encroachment element may be advantageous if load limits are a problem. To avoid extremely large
reach settings the D60 has the ability to implement any element, so that it is reverse looking. This strategy can be beneficial
if the reduced reach enhances the discrimination between the load and fault conditions. It should be recognized however
that, if adopted, this approach must be implemented at both ends of the protected line.
g) GROUND DISTANCE ZONE 5

An additional fifth ground distance zone can be used in special applications. This zone may be start zone for arming trip-
ping from all other zones, in both forward and reverse directions of the of protected line. This zone may also be used as an
additional reverse-looking zone for implementation of two reverse-looking zones, thus providing two zone backup reverse-
looking protection. The fifth distance zone can be used as an alarm zone, indicating that load impedance is approaching
the zone characteristic.

9.3 PROTECTION SIGNALING SCHEMES 9 APPLICATION OF SETTINGS
9.3PROTECTION SIGNALING SCHEMES 9.3.1 OVERVIEW
The D60 includes six common pilot-aided schemes:

• direct under-reaching transfer trip (DUTT)
• permissive under-reaching transfer trip (PUTT)
• permissive over-reaching transfer trip (POTT)
• hybrid permissive over-reaching transfer trip (Hybrid POTT)
• directional comparison blocking
• directional comparison unblocking
9.3.2 DIRECT UNDER-REACHING TRANSFER TRIP (DUTT)
This scheme uses an under-reaching Zone 1 distance element to key a transfer trip signal to the remote end(s), where on
receipt, the DUTT pilot scheme operates without any additional supervision.
For proper operation of the scheme the Zone 1 phase and ground distance elements must be enabled, configured and set
per rules of distance relaying.
The scheme generates an output operand (DUTT TX) that is used to transmit the signal to the remote end. Choices of com-
munications channel include Remote Inputs/Outputs and telecommunications interfaces. When used with telecommunica-
tions facilities the output operand should be assigned to operate an output contact connected to key the transmitter at the
interface.
Note that the same protection signaling may be used by a breaker failure scheme, in which case the signal can be sealed
in by breaker fail for a time longer than the auto-reclose “reclaim” time which then prevents auto-reclose when not required.
A provision for an optional seal-in of the send signal is made to cover those situations where PLC (Power Line Carrier) sig-
naling is used and the signal must be transmitted in a potentially noisy situation due to the fault.
The scheme output operand (DUTT OP) must be configured to interface with other relay functions, output contacts in par-
ticular, in order to make the scheme fully operational. Typically, the output operand should be programmed to initiate a trip,
breaker fail, and auto-reclose, and drive a user-programmable LED as per user application.
9.3.3 PERMISSIVE UNDER-REACHING TRANSFER TRIP (PUTT)
This scheme uses an under-reaching Zone 1 distance element to key a transfer trip signal to the remote end where it is
supervised by the over-reaching Zone 2 distance elements.
For proper operation of the scheme the Zone 1 and 2 phase and ground distance elements must be enabled, configured
and set per rules of distance relaying.
The scheme generates an output operand (PUTT TX) that is used to transmit the signal to the remote end. Choices of com-
interface.
The PUTT RX PICKUP DELAY timer can be used to ride through spurious PLC receive signals.
The scheme output operand (PUTT OP) must be configured to interface with other relay functions, output contacts in partic-
ular, in order to make the scheme fully operational. Typically, the output operand should be programmed to initiate a trip,
breaker fail, and auto-reclose, and drive a user-programmable LED as per user application.
9 9.3.4 PERMISSIVE OVER-REACHING TRANSFER TRIP (POTT)
This scheme is intended for two-terminal line applications only.

This scheme uses an over-reaching Zone 2 distance element to essentially compare the direction to a fault at both the ends
of the line.

9 APPLICATION OF SETTINGS 9.3 PROTECTION SIGNALING SCHEMES
Ground directional overcurrent functions available in the relay can be used in conjunction with the Zone 2 distance element
to key the scheme and initiate its operation. This provides increased coverage for high-resistance faults.
Good directional integrity is the key requirement for an over-reaching forward-looking protection element used to supple-
ment Zone 2. Even though any FlexLogic operand could be used for this purpose allowing the user to combine responses
of various protection elements, or to apply extra conditions through FlexLogic™ equations, this extra signal is primarily
meant to be the output operand from either the Negative-Sequence Directional IOC or Neutral Directional IOC. Both of
these elements have separate forward (FWD) and reverse (REV) output operands. The forward indication should be used
(NEG SEQ DIR OC1 FWD or NEUTRAL DIR OC1 FWD).
An important consideration is when one of the line terminals is open. It is then necessary to identify this condition and
arrange for a continuous sending of the permissive signal or use a slower but more secure echo feature to send a signal to
the other terminal, which is producing the fault infeed. With any echo scheme however, a means must be provided to avoid
a permanent lock up of the transmit/receive loop. The echo co-ordination (ECHO DURATION) and lock-out (ECHO LOCK-
OUT) timers perform this function by ensuring that the permissive signal is echoed once for a guaranteed duration of time
before going to a lockout for a settable period of time.
It should be recognized that in ring bus or breaker and a half situations, it may be the line disconnect or a combination of
the disconnect and/or the breaker(s) status that is the indication that the terminal is open.
The POTT RX PICKUP DELAY timer is included in the permissive receive path to ride through spurious receive outputs that
may be produced during external faults, when power line carrier is utilized as the communications medium.
No current reversal logic is included for the overreaching phase and ground distance elements, because long reaches are
not usually required for two terminal lines. A situation can occur however, where the ground distance element will have an
extended reach. This situation is encountered when it is desired to account for the zero sequence inter-circuit mutual cou-
pling. This is not a problem for the ground distance elements in the D60 which do have a current reversal logic built into
their design as part of the technique used to improve ground fault directionality.
Unlike the distance protection elements the ground directional overcurrent functions do not have their reach well defined,
therefore the current reversal logic is incorporated for the extra signal supplementing Zone 2 in the scheme. The transient
blocking approach for this POTT scheme is to recognize that a permissive signal has been received and then allow a setta-
ble time TRANS BLOCK PICKUP DELAY for the local forward looking directional element to pick up.
The scheme generates an output operand (POTT TX) that is used to transmit the signal to the remote end. Choices of com-
interface. Power Line Carrier (PLC) channels are not recommended for this scheme since the PLC signal can be inter-
rupted by a fault.
For proper operation of the scheme the Zone 2 phase and ground distance elements must be enabled, configured and set
per rules of distance relaying. The Line Pickup element should be enabled, configured and set properly to detect line-end-
open/weak-infeed conditions.
If used by this scheme, the selected ground directional overcurrent function(s) must be enabled, configured and set accord-
ingly The output operand from the scheme (POTT OP) must be configured to interface with other relay functions, output
contacts in particular, in order to make the scheme fully operational. Typically, the output operand should be programmed to
initiate a trip, breaker fail, and auto-reclose, and drive a user-programmable LED as per user application.
9.3.5 HYBRID POTT SCHEME (HYB-POTT)
Generally, this scheme uses an over-reaching Zone 2 distance element to essentially compare the direction to a fault at
both ends of the line. Ground directional overcurrent functions available in the relay can be used in conjunction with the
Zone 2 distance element to key the scheme and initiate its operation. This increases the coverage for high-resistance
faults.
The scheme is intended for three-terminal applications and for weak-infeed conditions. As a long reach of the overreaching
9
distance element may be required for three-terminal applications, transient blocking logic is provided for both distance and
ground directional overcurrent elements. In order to cope with weak-infeed conditions an echo feature is made available.
By default the scheme uses the reverse-looking Zone 4 distance element to identify reverse faults. Additionally, reverse-
looking ground directional overcurrent functions can be used in conjunction with Zone 4.

and set per rules of distance relaying. The Line Pickup element should be enabled, configured and set properly to detect
line-end-open/weak-infeed and undervoltage conditions.
If used by this scheme, the selected ground directional overcurrent function(s) must be enabled, configured, and set
accordingly.
The scheme generates an output operand (HYBRID POTT TX) that is used to transmit the signal to the remote end.
Choices of communications channel include Remote Inputs/Outputs and telecommunications interfaces. When used with
telecommunications facilities the output operand should be assigned to operate an output contact connected to key the
transmitter at the interface.
For more application recommendation refer to the POTT scheme.
The output operand from the scheme (HYBRID POTT OP) must be configured to interface with other relay functions, output
contacts in particular, in order to make the scheme fully operational. Typically, the output operand should be programmed to
initiate a trip, breaker fail, and auto-reclose, and drive a user-programmable LED as per user application.
9.3.6 DIRECTIONAL COMPARISON BLOCKING
Generally, the scheme compares the direction to a fault at both ends of the line. Unlike the permissive schemes, the
absence of a blocking signal permits operation of the scheme. Consequently, the scheme is biased toward dependability
and requires an “on/off” type of signaling.
By default this scheme uses only a forward-looking over-reaching Zone 2 distance element to identify forward faults.
Ground directional overcurrent functions available in the relay can be used in conjunction with the Zone 2 distance element
to increase the coverage for high-resistance faults.
By default the scheme uses only a reverse-looking Zone 4 distance element to identify reverse faults. Ground directional
overcurrent functions available in the relay can be used in conjunction with the Zone 4 distance element for better time and
sensitivity coordination.
and set per rules of distance relaying.
If used by this scheme, the selected ground directional overcurrent function(s) must be enabled, configured and set accord-
ingly.
The scheme generates output operands (BLOCKING SCHEME TX INIT and BLOCKING SCHEME TX STOP) that are
used control the transmission of signals to the remote end. Choices of communications channel include Remote Inputs/
Outputs and telecommunications interfaces. When used with telecommunications facilities the output operand should be
assigned to operate an output contact connected to key the transmitter at the interface.
A blocking scheme may be preferred over a Hybrid POTT scheme, because of shorter reach settings for the Zone 2 ele-
ments. This follows from the fundamental difference that all zone 2 elements are required to see an internal fault for the
POTT approach, under all system conditions, which in turn, means that the reversed Zone 4 block initiate elements must
also have an increased reach. A blocking scheme on the other hand, can have much shorter Zone 2 reach settings if
sequential clearance can be accepted. The simple rule to ensure that all faults can be cleared, is for each terminal to have
a reach setting equal to the distance to the tap plus twice the distance from the tap to the remote terminal.
The Zone 2 element must have a coordinating timer BLOCK RX CO-ORD PKP DELAY, to ensure that the blocking signal is
received for all external faults that are within the set reach of the local overreaching Zone 2.
Transient blocking logic is implemented via the TRANS BLOCK timer, which continues to send a blocking signal for a settable
time TRANS BLOCK RESET DELAY, if it was being sent for at least 30 ms during the initial reverse fault set via TRANS BLOCK
PICKUP DELAY.
9 The output operand from the scheme (BLOCKING SCHEME OP) must be configured to interface with other relay functions,
output contacts in particular, in order to make the scheme fully operational. Typically, the output operand should be pro-
grammed to initiate a trip, breaker fail, and auto-reclose, and drive a user-programmable LED as per user application.

9 APPLICATION OF SETTINGS 9.3 PROTECTION SIGNALING SCHEMES
9.3.7 DIRECTIONAL COMPARISON UNBLOCKING
a) OVERVIEW
The directional comparison unblocking scheme is used with a frequency shift keying (FSK) PLC that produces a loss-of-
guard output during an actual loss-of-guard signal condition and during reception of the permissive keyed frequency when
the received carrier signal changed from guard to permissive frequency. The loss-of-guard signal should preferably be a
normally-closed contact, allowing the scheme to get this signal if the communications equipment failed. This loss-of-guard
output should be connected to a contact input of the D60. The power line carrier should also provide an output contact
when the permissive frequency is received. This output should be wired to any other contact input of the D60.
The directional comparison unblocking scheme allows a window of opportunity for tripping the breaker fast if the permissive
signal gets attenuated by the fault to a level below the receiver's threshold. The guard signal is monitored, and the relay is
allowed to trip for a loss of guard without receipt of the permissive signal, if the relay sees the fault in the forward, and not
reverse direction by means of the forward looking distance zone 2 and ground directional forward, if configured, and
reverse looking distance zone 4 and ground directional reverse, if configured.
The scheme is active and ready for operation when the DCUB BLOCK setting is “Off” the DCUB SCHEME FUNCTION setting is
“Enabled”. The user can disable or block the scheme by assigning any FlexLogic operand to the DCUB BLOCK setting. This
operand can consist of any pre-defined logic, including a pilot cutout switch connected to any contact input of the D60. With
this pilot cutout switch and the pre-defined logic state on and assigned to DCUB BLOCK, the scheme will be disabled. The
directional comparison unblocking scheme supervises the operation and keying of all scheme functions. The lockout fea-
ture of the scheme also supervises all scheme functions. All timers are fully adjustable, with typical values indicated.
Lockout of the directional comparison unblocking scheme is established as follows. Lockout of the scheme is started for a
time duration set by DCUB LOG TRIP WINDOW setting if:
• The scheme is enabled and not blocked (that is, the scheme is active), and
• no permissive RX signal is received, and
• any loss-of-guard signal is received.
Lockout is sealed-in through an AND gate with the directional comparison unblocking scheme active and any loss-of-guard
through GUARD HEALTHY RESET DELAY timer. The scheme will thus remain blocked during longer loss-of-guard or channel
conditions for any of the configured channels. The GUARD HEALTHY RESET DELAY timer ensures that the scheme will remain
locked out slightly longer after the loss-of-guard signal(s) is reset. This allows for all channel(s) stabilizing and contact
denouncing. This timer determines how long the logic waits before enabling the directional comparison unblocking scheme
when the communications channel is restored.
Operating of the directional comparison unblocking scheme consists of two parts: normal operation and loss-of-guard oper-
ation.
b) NORMAL OPERATION
Normal operation picks up under the following conditions:
• The scheme is enabled (DCUB FUNCTION is “Enabled” and DCUB BLOCK is “Off”), and
• any permissive signal is received with its associated loss-of-guard signal (e.g. DCUB RX1 and DCUB LOG1), and
• a fault is seen in the forward zone 2 distance elements or ground directional forward function (if configured), and
• the reverse zone 4 distance elements or ground directional reverse function (if configured) did not pickup to set the
transient blocking, and
• the scheme is not locked out.
If these conditions are met, the trip table is run, operating the scheme and asserting DCUB OP FlexLogic operand. The trip
table with the aid of the local phase selector and received RX signals will determine what tripping operands will be oper-
ated. During normal operation, the loss-of-guard signal will be seen momentarily before the permissive DCUB RX signal is
9
received for each channel being operated, as the channel transitions from guard to permissive frequency, but the scheme
operates instantaneously after any DCUB RX signal is received.

c) LOSS-OF-GUARD OPERATION
The loss-of-guard operation picks under the following conditions:
• any loss-of-guard signal is received without its associated RX signal, and
transient blocking.
If these conditions are met, then the DCUB LOG PICKUP DELAY timer is started. After this timer times out, the trip table is run,
operating the scheme and asserting the DCUB OP FlexLogic operand. The trip table with the aid of the local phase selector
and loss-of-guard signals will determine what tripping operands will be operated. The DCUB LOG PICKUP DELAY timer allows
for any and all channel(s) to transition from guard to permissive before operating due to loss-of-guard in the presence of a
forward fault. The time window of allowing the scheme to operate when no DCUB RX signal is received when any loss-of-
guard was received is the difference between the DCUB LOG TRIP WINDOW and DCUB LOG PICKUP DELAY timers. When using
default settings, this value is 150 – 8 = 142ms. This means the scheme is unblocked and can trip during this time window if
a forward fault is sensed.
d) KEYING OF THE CARRIER(S) UNDER NORMAL CONDITIONS

The keying signals, which allows the relay to key the permissive channel during normal permissive scheme operation by
means of the DCUB TX1 through DCUB TX4 signals, are established as follows:
transient blocking.
If these conditions are met, then the scheme will key the channel(s) by means of asserting transmit signals DCUB TX1
through DCUB TX4 with the aid of the local phase selector or zone 2 distance elements.
e) KEYING OF THE CARRIER DURING ECHO CONDITIONS

The echo signal, which allows the relay to key the permissive channel(s) through the DCUB TX1 through DCUB TX4 transmit
operands during echo conditions when the local breaker opened, will key the carrier(s) during the following conditions:
• the DCUB PERMISSIVE ECHO setting is “Enabled”, and
• the LINE PICKUP LEO PKP operand that detects the local breaker to be open picks up for a time set by LINE END OPEN
PICKUP DELAY, and
• any permissive signal DCUB RX1 through DCUB RX4 is received and any LOG1 to LOG4 is received, and
• a fault is not seen in the forward zone 2 distance elements or ground directional forward function (if configured) for at
least 100 ms, and
transient blocking.
If these conditions are met, then the scheme will echo (transmit the DCUB TX1 through DCUB TX4 operands) the received
permissive DCUB RX signal(s) back to the remote relay based on the echo table.
The keying or transmit signals DCUB TX1 through DCUB TX4 consist of all normal keying or echo keying conditions.
9 The scheme DCUB TRIP A, DCUB TRIB B, DCUB TRIP C, and DCUB TRIP 3P output operands are hard-wired to the trip output
scheme. As such, if the trip output or breaker control operands (if the breaker control function is used) are used for tripping,
the scheme fully operational. The permissive key carrier signals DCUB TX1 through DCUB TX4 must still be assigned to the
tripping/operating logic, and to output contacts as per the usual D60 logic/output assignments.

9 APPLICATION OF SETTINGS 9.4 SERIES COMPENSATED LINES
9.4SERIES COMPENSATED LINES 9.4.1 INTRODUCTION
For reasons described in Chapter 8: Theory of Operation, it is recommended to apply a combination of distance, ground
directional overcurrent and high-set overcurrent functions for protection of series compensated lines.
The setting rules described below must take into account variety of system configurations, particularly a status of series
capacitors (in-service, by-passed). Either the worst-case topology shall be considered or - if possible - adaptive settings
shall be applied though the multiple settings groups mechanism.
A line compensating capacitor is a bank of three physical capacitors and their overvoltage protecting devices (air gaps and/
or MOVs). If none of the MOV/gaps conducts any significant current, the positive-, negative- and zero-sequence reactance
of the three-phase bank equal the reactance of the actual (phase) capacitors. Under asymmetrical conditions, however,
such as a single line to ground fault, when only one MOV/gap may operate, the series capacitor bank would create extra
(series) asymmetry in addition to the fault (shunt) asymmetry. The positive-, negative- and zero-sequence impedances will
differ from each other and will not equal the impedance of the phase capacitors. Moreover, there may be mutual coupling
between the sequence networks representing the series capacitor bank. This makes analytical analysis of fault conditions
very burdensome. For setting calculations, however, it is justified to assume the zero-, positive-, and negative-sequence
reactance of the capacitor bank equal the reactance of the actual (phase) capacitors. This represents a worst-case low-cur-
rent fault scenario, when the steady-state effects of series compensation are most weighty.
9.4.2 DISTANCE
Traditionally, the reach setting of an underreaching distance function shall be set based on the net inductive impedance
between the potential source of the relay and the far-end busbar, or location for which the zone must not overreach. Faults
behind series capacitors on the protected and adjacent lines need to be considered for this purpose. For further illustration
a sample system shown in the figure below is considered.
voltage
SENDING RECEIVING
protection reactance
BUS BUS
level
0.5 pu 0.6 pu 0.5 pu 0.7 pu
-2 Ω -4 Ω -3 Ω -5 Ω
INFINITE
INFINITE
3Ω 10 Ω 7Ω
BUS
BUS
F2 A B B A F1
Protected Line
Figure 9–2: SAMPLE SERIES COMPENSATED SYSTEM
Assuming 20% security margin, the underreaching zone shall be set as follows.
At the Sending Bus, one must consider an external fault at F1 as the 5  capacitor would contribute to the overreaching
effect. Any fault behind F1 is less severe as extra inductive line impedance increases the apparent impedance:
Reach Setting: 0.8 x (10 – 3 – 5) = 1.6  if the line-side (B) VTs are used
Reach Setting: 0.8 x (10 – 4 – 3 – 5) = –1.6  if the bus-side (A) VTs are used
The negative value means that an underreaching zone cannot be used as the circuit between the potential source of the
relay and an external fault for which the relay must not pick-up, is overcompensated, i.e. capacitive.
At the Receiving Bus, one must consider a fault at F2:
Reach Setting: 0.8 x (10 – 4 – 2) = 3.2  if the line-side (B) VTs are used
Reach Setting: 0.8 x (10 – 4 – 3 – 2) = 0.8  if the bus-side (A) VTs are used 9
Practically, however, to cope with the effect of sub-synchronous oscillations, one may need to reduce the reach even more.
As the characteristics of sub-synchronous oscillations are in complex relations with fault and system parameters, no solid
setting recommendations are given with respect to extra security margin for sub-synchronous oscillations. It is strongly rec-
ommended to use a power system simulator to verify the reach settings or to use an adaptive D60 feature for dynamic
reach control.
If the adaptive reach control feature is used, the PHS DIST Z1 VOLT LEVEL setting shall be set accordingly.

9.4 SERIES COMPENSATED LINES 9 APPLICATION OF SETTINGS
This setting is a sum of the overvoltage protection levels for all the series capacitors located between the relay potential
source and the far-end busbar, or location for which the zone must not overreach. The setting is entered in pu of the phase
VT nominal voltage (RMS, not peak value).
If a minimum fault current level (phase current) is causing a voltage drop across a given capacitor that prompts its air gap to
flash over or its MOV to carry practically all the current, then the series capacitor shall be excluded from the calculations
(the capacitor is immediately by-passed by its overvoltage protection system and does not cause any overreach problems).
If a minimum fault current does not guarantee an immediate capacitor by-pass, then the capacitor must be included in the
calculation: its overvoltage protection level, either air gap flash-over voltage or MOV knee-point voltage, shall be used
(RMS, not peak value).
Assuming none of the series capacitors in the sample system is guaranteed to get by-passed, the following calculations
apply:
For the Sending Bus: 0.5 + 0.7 = 1.2 pu if the line-side (B) VTs are used
0.6 + 0.5 + 0.7 = 1.8 pu if the bus-side (A) VTs are used
For the Receiving Bus: 0.6 + 0.5 = 1.1 pu if the line-side (B) VTs are used
0.6 + 0.5 + 0.5 = 1.6 pu if the bus-side (A) VTs are used
9.4.3 GROUND DIRECTIONAL OVERCURRENT
Ground directional overcurrent function (negative-sequence or neutral) uses an offset impedance to guarantee correct fault
direction discrimination. The following setting rules apply.
1. If the net impedance between the potential source and the local equivalent system is inductive, then there is no need
for an offset. Otherwise, the offset impedance shall be at least the net capacitive reactance.
2. The offset cannot be higher than the net inductive reactance between the potential source and the remote equivalent
system. For simplicity and extra security, the far-end busbar may be used rather than the remote equivalent system.
As the ground directional functions are meant to provide maximum fault resistance coverage, it is justified to assume that
the fault current is very low and none of the series capacitors is guaranteed to get by-passed. Consider settings of the neg-
ative-sequence directional overcurrent protection element for the Sample Series Compensated System.
For the Sending Bus relay, bus-side VTs:
• Net inductive reactance from the relay into the local system = –2 + 3 = 1  > 0; there is no need for offset.
• Net inductive reactance from relay through far-end busbar = –4 + 10 – 3 = 3 ; the offset cannot be higher than 3 .
• It is recommended to use 1.5  offset impedance.
For the Sending Bus relay, line-side VTs:
• Net inductive reactance from relay into local system = –2 + 3 – 4 = –3  < 0; an offset impedance 3  must be used.
• Net inductive reactance from relay through far-end busbar = 10 – 3 = 7 ; the offset cannot be higher than 7 .
• It is recommended to use 5  offset impedance.
For the Receiving Bus relay, bus-side VTs:
• Net inductive reactance from relay into local system = –5 + 7 = 2  > 0; there is no need for offset.
• Net inductive reactance from relay through far-end busbar = –3 + 10 – 4 = 3 ; the offset cannot be higher than 3 .
For the Receiving Bus relay, line-side VTs:
9 • Net inductive reactance from relay into local system = –3 – 5 + 7 = –1  < 0; an offset impedance 1  must be used.
• Net inductive reactance from relay through far-end busbar = 10 – 4 = 6 ; the offset cannot be higher than 6 .
9.4.4 HIGH-SET PHASE OVERCURRENT
The setting rules for high-set overcurrent protection are explained in the High-Set Overcurrent Elements section.

9 APPLICATION OF SETTINGS 9.5 PHASE DISTANCE THROUGH POWER TRANSFORMERS
9.5PHASE DISTANCE THROUGH POWER TRANSFORMERS 9.5.1 PHASE DISTANCE PROTECTION
a) DESCRIPTION
Phase distance elements of the D60 could be set to respond to faults beyond any three-phase power transformer. The
relay guarantees accurate reach and targeting for any phase fault. Moreover, the current and voltage transformers may be
located independently on different sides of the transformer.
The following setting rules apply to this feature:
1. A given distance zone is terminated by location of the VTs, not the CTs.
2. Consequently, the positive-sequence impedance of a transformer must be included in the reach setting only if the
transformer is located between the potential source and the intended reach point.
3. The current signals require compensation if the transformer is located between the CTs and the intended reach point.
If this is the case the CT connection setting shall be set to transformer connection and vector group as seen from the
CTs toward the reach point. Otherwise, the CT connection setting shall be set to "None".
4. The voltage signals require compensation if the transformer is located between the VTs and the intended reach point.
If this is the case the VT connection setting shall be set to transformer connection and vector group as seen from the
VTs toward the reach point. Otherwise, the VT connection setting shall be set to "None".
5. The reach setting is entered in secondary ohms and as such must take into account location and ratios of VTs and CTs
as well as voltage ratio of the involved power transformer.
The following equations explain the setting rules. Consider two applications as shown in the figure below:
(a) (b)
ZH ZT ZX ZH ZT ZX
H X H X
Z4 Z1 Z4 Z1
Figure 9–3: PHASE DISTANCE LOOKING THROUGH A POWER TRANSFORMER

where: ZX = intended reach impedance for Zone 1 (primary ohms)
ZH = intended reach impedance for Zone 4 (primary ohms)
ZT = positive-sequence impedance of the transformer
VX, VH = transformer rated voltages
nCT = transformation ratio of the CTs
nVT = transformation ratio of the VTs
Z1: Z1 reach setting (secondary ohms)
Z4: Zone 4 reach setting (secondary ohms)
b) ZONE 1 SETTING IN APPLICATION (A)

As the transformer is located between the potential source and the reach point for Zone 1, the reach impedance must
include the positive-sequence impedance of the transformer. In addition, the primary impedance must be re-calculated for
the voltage level of the VTs and CTs, and eventually, re-calculated to secondary quantities:
V H 2 n CT
Z 1 =  Z T  at X  + Z x    -------  --------- (EQ 9.4)
9
 V X n VT

9.5 PHASE DISTANCE THROUGH POWER TRANSFORMERS 9 APPLICATION OF SETTINGS
c) ZONE 4 SETTING IN APPLICATION (A)

As the transformer is not located between the potential source and the reach point for Zone 4, the reach impedance must
not include the positive-sequence impedance of the transformer. Because both VTs and CTs are located on the same side
as the intended reach point, no correction for the transformer ratio is required. The primary impedance must be only re-cal-
culated to secondary quantities:
n CT
Z 4 = Z H  --------- (EQ 9.5)
n VT
d) ZONE 1 SETTING IN APPLICATION (B)

As the transformer is not located between the potential source and the reach point for Z1, the reach impedance must not
include the positive-sequence impedance of the transformer. The CTs are located on the other side of the transformer, thus
transformer ratio must be included:
VH n CT
Z 1 = Z X   -------  --------- (EQ 9.6)
 V X n VT
e) ZONE 4 SETTING IN APPLICATION (B)

As the transformer is located between the potential source and the reach point for Zone 4, the reach impedance must
include the positive-sequence impedance of the transformer. The VTs are located on the other side of the transformer, thus
transformer ratio must be included:
VX n CT
Z 4 =  Z T  at H  + Z H    -------  --------- (EQ 9.7)
VH n VT
9.5.2 EXAMPLE
Given the following for the system shown in the previous section:
ZX = 30  85° (intended reach of Zone 1)
ZH = 0.06  88° (intended reach of Zone 4)
nCT = 8000:5 = 1600 (located at H)
nVT = 315000:120 = 2625 (located at X)
Transformer: 13.8/315 kV, 150 MVA, 10%, delta/wye, 315 kV side lagging 30°
Transformer impedance:
2
10  13.8 
Z T  at H  = ----------  ------------------- = 0.127 90 (EQ 9.8)
100 150
The Zone 1 settings are:
13.8 1600
Z 1 = 30  -----------  ------------- = 0.8011 85 (EQ 9.9)
315 2625
PHS DIST Z1 REACH: "0.80"
PHS DIST Z1 RCA: "85"
PHS DIST Z1 XMFR VOL CONNECTION: "None"
PHS DIST Z1 XMFR CUR CONNECTION: "Dy1"
The Zone 4 settings are:

9 315 1600
Z 4 =  0.127 90 + 0.006 88   -----------  ------------- = 2.601 89.4 (EQ 9.10)
13.8 2625
PHS DIST Z4 REACH: "2.60"
PHS DIST Z4 RCA: "89"
PHS DIST Z4 XMFR VOL CONNECTION: "Yd11"
PHS DIST Z4 XMFR CUR CONNECTION: "None"

10 MAINTENANCE 10.1 MODULES
10 MAINTENANCE 10.1 MODULES 10.1.1 REPLACE A MODULE
Withdraw or insert a module only when control power has been removed from the unit, and be
sure to insert only the correct module type into a slot, else personal injury, damage to the unit
or connected equipment, or undesired operation can result.
To avoid damage to the equipment, use proper electrostatic discharge protection (for example, a
static strap) when coming in contact with modules while the relay is energized.
The relay, being modular in design, allows for the withdrawal and insertion of modules. Modules must only be replaced with
like modules in their original factory configured slots.
The enhanced faceplate can be opened to the left, once the thumb screw has been removed, as shown below. This allows
for easy accessibility of the modules for withdrawal. The new wide-angle hinge assembly in the enhanced front panel opens
completely and allows easy access to all modules in the D60.
842812A1.CDR
Figure 10–1: UR MODULE WITHDRAWAL AND INSERTION (ENHANCED FACEPLATE)

The standard faceplate can be opened to the left, once the sliding latch on the right side has been pushed up, as shown
below. This allows for easy accessibility of the modules for withdrawal.
Figure 10–2: UR MODULE WITHDRAWAL AND INSERTION (STANDARD FACEPLATE)

To properly remove a module, the ejector/inserter clips, located at the top and bottom of each module, must be pulled
simultaneously. Before performing this action, control power must be removed from the relay. Record the original loca-
tion of the module to ensure that the same or replacement module is inserted into the correct slot. Modules with current 10
input provide automatic shorting of external CT circuits.

10.1 MODULES 10 MAINTENANCE
To properly insert a module, ensure that the correct module type is inserted into the correct slot position. The ejector/
inserter clips located at the top and at the bottom of each module must be in the disengaged position as the module is
smoothly inserted into the slot. Once the clips have cleared the raised edge of the chassis, engage the clips simultaneously.
When the clips have locked into position, the module will be fully inserted.
CPU connections must be individually disconnected from the module before the module can be removed from the
chassis.
NOTE
The new CT/VT modules can only be used with new CPUs; similarly, old CT/VT modules can only be used with old
CPUs. In the event that there is a mismatch between the CPU and CT/VT module, the relay does not function and
NOTE a DSP ERROR or HARDWARE MISMATCH error displays.
10

10 MAINTENANCE 10.2 BATTERIES
10.2 BATTERIES 10.2.1 REPLACE BATTERY
When required, the battery can be replaced. The power supply module contains the battery.
To avoid injury, ensure that the unit has been powered off for a minimum of three minutes
before replacing the battery.
Risk of fire if battery is replaced with incorrect type or polarity.
To replace the battery:
1. Turn off the power to the unit.
2. Wait a minimum of three minutes to ensure that there is no power to the battery.
3. As outlined in the previous section, open the unit by sliding up the latch on the right side of the front panel and opening
the panel to the left.
4. Unscrew the bracket on the front left of the unit so that you can open fully the front panel to access the power supply
module, which is typically in the first slot on the left side.
5. Simultaneously pull the ejector clips at the top and bottom of the power supply module and remove the module.
6. Unscrew the screw that attaches the metal cover to the module.
7. Slide the metal cover away from the clips about 1 cm (1/4 inch) and remove the cover.
8. Unclip the black plastic holder that keeps the battery in place. The plastic clips into the socket at the bottom on both
sides. Use a flat-head screwdriver if you cannot unclip the plastic with your fingers.
9. Observe the + and - polarity of the battery and replace it with the same polarity as marked on the battery holder.
Replace the battery with the identical make and model. For example, do not use a rechargeable battery.
Figure 10–3: BATTERY LOCATION ON POWER SUPPLY MODULE
10. Reinstall the battery clip and the metal cover, and reinsert the power supply module into the unit.
11. Power on the unit.
12. Dispose of the old battery as outlined in the next section.
10

10.2 BATTERIES 10 MAINTENANCE
10.2.2 DISPOSE OF BATTERY
EN Battery Disposal
This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product
documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium
(Cd), lead (Pb), or mercury (Hg). For proper recycling return the battery to your supplier or to a designated collection point. For more
information see: www.recyclethis.info.
CS Nakládání s bateriemi
Tento produkt obsahuje baterie, které nemohou být zneškodněny v Evropské unii jako netříděný komunální odpadu. Viz dokumentace k
produktu pro informace pro konkrétní baterie. Baterie je označena tímto symbolem, který může zahrnovat i uvedena písmena, kadmium
(Cd), olovo (Pb), nebo rtuť (Hg). Pro správnou recyklaci baterií vraťte svémudodavateli nebo na určeném sběrném místě. Pro více informací
viz: www.recyclethis.info.
DA Batteri affald
Dette produkt indeholder et batteri som ikke kan bortskaffes sammen med almindeligt husholdningsaffald i Europa. Se
produktinformation for specifikke informationer om batteriet. Batteriet er forsynet med indgraveret symboler for hvad batteriet
indeholder: kadmium (Cd), bly (Pb) og kviksølv (Hg). Europæiske brugere af elektrisk udstyr skal aflevere kasserede produkter til genbrug
eller til leverandøren. Yderligere oplysninger findes på webstedet www.recyclethis.info.
DE Entsorgung von Batterien
Dieses Produkt beinhaltet eine Batterie, die nicht als unsortierter städtischer Abfall in der europäischen Union entsorgt werden darf.
Beachten Sie die spezifischen Batterie-informationen in der Produktdokumentation. Die Batterie ist mit diesem Symbol gekennzeichnet,
welches auch Hinweise auf möglicherweise enthaltene Stoffe wie Kadmium (Cd), Blei (Pb) oder Quecksilber (Hektogramm) darstellt. Für
die korrekte Wiederverwertung bringen Sie diese Batterie zu Ihrem lokalen Lieferanten zurück oder entsorgen Sie das Produkt an den
gekennzeichneten Sammelstellen. Weitere Informationen hierzu finden Sie auf der folgenden Website: www.recyclethis.info.
EL Απόρριψη μπαταριών
Αυτό το προϊόν περιέχει μια μπαταρία που δεν πρέπει να απορρίπτεται σε δημόσια συστήματα απόρριψης στην Ευρωπαϊκή
Κοινότητα. ∆είτε την τεκμηρίωση του προϊόντος για συγκεκριμένες πληροφορίες που αφορούν τη μπαταρία. Η μπαταρία είναι φέρει
σήμανση με αυτό το σύμβολο, το οποίο μπορεί να περιλαμβάνει γράμματα για να δηλώσουν το κάδμιο (Cd), τον μόλυβδο (Pb), ή τον
υδράργυρο (Hg). Για την κατάλληλη ανακύκλωση επιστρέψτε την μπαταρία στον προμηθευτή σας ή σε καθορισμένο σημείο συλλογής.
Για περισσότερες πληροφορίες δείτε: www.recyclethis.info.
ES Eliminacion de baterias
Este producto contiene una batería que no se pueda eliminar como basura normal sin clasificar en la Unión Europea. Examine la
documentación del producto para la información específica de la batería. La batería se marca con este símbolo, que puede incluir siglas
para indicar el cadmio (Cd), el plomo (Pb), o el mercurio (Hg ). Para el reciclaje apropiado, devuelva este producto a su distribuidor ó
deshágase de él en los puntos de reciclaje designados. Para mas información : wwwrecyclethis.info.
ET Patareide kõrvaldamine
Käesolev toode sisaldab patareisid, mida Euroopa Liidus ei tohi kõrvaldada sorteerimata olmejäätmetena. Andmeid patareide kohta
vaadake toote dokumentatsioonist. Patareid on märgistatud käesoleva sümboliga, millel võib olla kaadmiumi (Cd), pliid (Pb) või
elavhõbedat (Hg) tähistavad tähed. Nõuetekohaseks ringlusse võtmiseks tagastage patarei tarnijale või kindlaksmääratud
vastuvõtupunkti. Lisainformatsiooni saab Internetist aadressil: www.recyclethis.info.
FI Paristoje ja akkujen hävittäminen
Tuote sisältää pariston, jota ei saa hävittää Euroopan Unionin alueella talousjätteen mukana. Tarkista tuoteselosteesta tuotteen tiedot.
Paristo on merkitty tällä symbolilla ja saattaa sisältää cadmiumia (Cd), lyijyä (Pb) tai elohopeaa (Hg). Oikean kierrätystavan
varmistamiseksi palauta tuote paikalliselle jälleenmyyjälle tai palauta se paristojen keräyspisteeseen. Lisätietoja sivuilla
www.recyclethis.info.
FR Élimination des piles
Ce produit contient une batterie qui ne peuvent être éliminés comme déchets municipaux non triés dans l'Union européenne. Voir la
documentation du produit au niveau des renseignements sur la pile. La batterie est marqué de ce symbole, qui comprennent les
indications cadmium (Cd), plomb (Pb), ou mercure (Hg). Pour le recyclage, retourner la batterie à votre fournisseur ou à un point de
collecte. Pour plus d'informations, voir: www.recyclethis.info.
10

10 MAINTENANCE 10.2 BATTERIES
HU Akkumulátor hulladék kezelése

Ezen termék akkumulátort tartalmaz, amely az Európai Unión belül csak a kijelölt módon és helyen dobható ki. A terméken illetve a
mellékelt ismertetőn olvasható a kadmium (Cd), ólom (Pb) vagy higany (Hg) tartalomra utaló betűjelzés. A hulladék akkumulátor leadható
a termék forgalmazójánál új akkumulátor vásárlásakor, vagy a kijelölt elektronikai hulladékudvarokban. További információ a
www.recyclethis.info oldalon.
IT Smaltimento batterie
Questo prodotto contiene una batteria che non può essere smaltita nei comuni contenitori per lo smaltimento rifiuti, nell' Unione
Europea. Controllate la documentazione del prodotto per le informazioni specifiche sulla batteria. La batteria è contrassegnata con
questo simbolo e può includere alcuni caratteri ad indicare la presenza di cadmio (Cd), piombo (Pb) oppure mercurio (Hg). Per il corretto
smaltimento, potete restituirli al vostro fornitore locale, oppure rivolgervi e consegnarli presso i centri di raccolta preposti. Per maggiori
informazioni vedere: ww.recyclethis.info.
LT Baterijų šalinimas
Šios įrangos sudėtyje yra baterijų, kurias draudžiama šalinti Europos Sąjungos viešose nerūšiuotų atliekų šalinimo sistemose. Informaciją
apie baterijas galite rasti įrangos techninėje dokumentacijoje. Baterijos žymimos šiuo simboliu, papildomai gali būti nurodoma kad
baterijų sudėtyje yra kadmio (Cd), švino (Pb) ar gyvsidabrio (Hg). Eksploatavimui nebetinkamas baterijas pristatykite į tam skirtas
surinkimo vietas arba grąžinkite jas tiesioginiam tiekėjui, kad jos būtų tinkamai utilizuotos. Daugiau informacijos rasite šioje interneto
svetainėje: www.recyclethis.info.
LV Bateriju likvidēšana
Šis produkts satur bateriju vai akumulatoru, kuru nedrīkst izmest Eiropas Savienībā esošajās sadzīves atkritumu sistēmās. Sk. produkta
dokumentācijā, kur ir norādīta konkrēta informācija par bateriju vai akumulatoru. Baterijas vai akumulatora marķējumā ir šis simbols,
kas var ietvert burtus, kuri norāda kadmiju (Cd), svinu (Pb) vai dzīvsudrabu (Hg). Pēc ekspluatācijas laika beigām baterijas vai akumulatori
jānodod piegādātājam vai specializētā bateriju savākšanas vietā. Sīkāku informāciju var iegūt vietnē: www.recyclethis.info.
NL Verwijderen van baterijen
Dit product bevat een batterij welke niet kan verwijdert worden via de gemeentelijke huisvuilscheiding in de Europese Gemeenschap.
Gelieve de product documentatie te controleren voor specifieke batterij informatie. De batterijen met deze label kunnen volgende
indictaies bevatten cadium (Cd), lood (Pb) of kwik (Hg). Voor correcte vorm van kringloop, geef je de producten terug aan jou locale
leverancier of geef het af aan een gespecialiseerde verzamelpunt. Meer informatie vindt u op de volgende website: www.recyclethis.info.
NO Retur av batteri
Dette produkt inneholder et batteri som ikke kan kastes med usortert kommunalt søppel i den Europeiske Unionen. Se
produktdokumentasjonen for spesifikk batteriinformasjon. Batteriet er merket med dette symbolet som kan inkludere symboler for å
indikere at kadmium (Cd), bly (Pb), eller kvikksølv (Hg) forekommer. Returner batteriet til leverandøren din eller til et dedikert
oppsamlingspunkt for korrekt gjenvinning. For mer informasjon se: www.recyclethis.info.
PL Pozbywanie się zużytych baterii
Ten produkt zawiera baterie, które w Unii Europejskiej mogą być usuwane tylko jako posegregowane odpady komunalne. Dokładne
informacje dotyczące użytych baterii znajdują się w dokumentacji produktu. Baterie oznaczone tym symbolem mogą zawierać
dodatkowe oznaczenia literowe wskazujące na zawartość kadmu (Cd), ołowiu (Pb) lub rtęci (Hg). Dla zapewnienia właściwej utylizacji,
należy zwrócić baterie do dostawcy albo do wyznaczonego punktu zbiórki. Więcej informacji można znaleźć na stronie internetowej
www.recyclethis.info.
PT Eliminação de Baterias
Este produto contêm uma bateria que não pode ser considerado lixo municipal na União Europeia. Consulte a documentação do
produto para obter informação específica da bateria. A bateria é identificada por meio de este símbolo, que pode incluir a rotulação
para indicar o cádmio (Cd), chumbo (Pb), ou o mercúrio (hg). Para uma reciclagem apropriada envie a bateria para o seu fornecedor ou
para um ponto de recolha designado. Para mais informação veja: www.recyclethis.info.
RU Утилизация батарей
Согласно европейской директиве об отходах электрического и электронного оборудования, продукты, содержащие батареи,
нельзя утилизировать как обычные отходы на территории ЕС. Более подробную информацию вы найдете в документации к
продукту. На этом символе могут присутствовать буквы, которые означают, что батарея собержит кадмий (Cd), свинец (Pb) или ртуть
(Hg). Для надлежащей утилизации по окончании срока эксплуатации пользователь должен возвратить батареи локальному
поставщику или сдать в специальный пункт приема. Подробности можно найти на веб-сайте: www.recyclethis.info.
SK Zaobchádzanie s batériami
Tento produkt obsahuje batériu, s ktorou sa v Európskej únii nesmie nakladať ako s netriedeným komunálnym odpadom. Dokumentácia
k produktu obsahuje špecifické informácie o batérii. Batéria je označená týmto symbolom, ktorý môže obsahovať písmená na označenie
kadmia (Cd), olova (Pb), alebo ortuti (Hg). Na správnu recykláciu vráťte batériu vášmu lokálnemu dodávateľovi alebo na určené zberné
miesto. Pre viac informácii pozrite: www.recyclethis.info.
SL Odlaganje baterij
Ta izdelek vsebuje baterijo, ki je v Evropski uniji ni dovoljeno odstranjevati kot nesortiran komunalni odpadek. Za posebne informacije o
bateriji glejte dokumentacijo izdelka. Baterija je označena s tem simbolom, ki lahko vključuje napise, ki označujejo kadmij (Cd), svinec (Pb)
ali živo srebro (Hg). Za ustrezno recikliranje baterijo vrnite dobavitelju ali jo odstranite na določenem zbirališču. Za več informacij obiščite
10
spletno stran: www.recyclethis.info.

10.2 BATTERIES 10 MAINTENANCE
SV Kassering av batteri
Denna produkt innehåller ett batteri som inte får kastas i allmänna sophanteringssytem inom den europeiska unionen. Se
produktdokumentationen för specifik batteriinformation. Batteriet är märkt med denna symbol, vilket kan innebära att det innehåller
kadmium (Cd), bly (Pb) eller kvicksilver (Hg). För korrekt återvinning skall batteriet returneras till leverantören eller till en därför avsedd
deponering. För mer information, se: www.recyclethis.info.
TR Pil Geri Dönüşümü
Bu ürün Avrupa Birliği genel atık sistemlerine atılmaması gereken pil içermektedir. Daha detaylı pil bilgisi için ürünün kataloğunu
inceleyiniz. Bu sembolle işaretlenmiş piller Kadmiyum(Cd), Kurşun(Pb) ya da Civa(Hg) içerebilir. Doğru geri dönüşüm için ürünü yerel
tedarikçinize geri veriniz ya da özel işaretlenmiş toplama noktlarına atınız. Daha fazla bilgi için: www.recyclethis.info.
Global Contacts
North America 905-294-6222
Latin America +55 11 3614 1700
Europe, Middle East, Africa +(34) 94 485 88 00
Asia +86-21-2401-3208
India +91 80 41314617
From GE Part Number 1604-0021-A1, GE Publication Number GEK-113574
10

APPENDIX A A.1 PARAMETER LISTS
AppendicesAPPENDIX A FlexAnalog and FlexInteger ParametersA.1Parameter Lists A.1.1 FLEXANALOG ITEMS
FlexAnalog items are also viewable in a web browser. In the browser, enter the IP address of the UR, access the Device
A
Information Menu option, then the FlexAnalog Parameter Listing option.
Table A–1: FLEXANALOG DATA ITEMS (Sheet 1 of 11)

ADDRESS FLEXANALOG NAME UNITS DESCRIPTION
5760 Sns Dir Power 1 Watts Sensitive directional power 1 actual value
5762 Sns Dir Power 2 Watts Sensitive directional power 2 actual value
5824 Field RTD 1 Value --- Field RTD 1 value
5832 Field TDR 1 Value --- Field TDR 1 value
6144 SRC 1 Ia RMS Amps Source 1 phase A current RMS
6146 SRC 1 Ib RMS Amps Source 1 phase B current RMS
6148 SRC 1 Ic RMS Amps Source 1 phase C current RMS
6150 SRC 1 In RMS Amps Source 1 neutral current RMS
6152 SRC 1 Ia Mag Amps Source 1 phase A current magnitude
6154 SRC 1 Ia Angle Degrees Source 1 phase A current angle
6155 SRC 1 Ib Mag Amps Source 1 phase B current magnitude
6157 SRC 1 Ib Angle Degrees Source 1 phase B current angle
6158 SRC 1 Ic Mag Amps Source 1 phase C current magnitude
6160 SRC 1 Ic Angle Degrees Source 1 phase C current angle
6161 SRC 1 In Mag Amps Source 1 neutral current magnitude
6163 SRC 1 In Angle Degrees Source 1 neutral current angle
6164 SRC 1 Ig RMS Amps Source 1 ground current RMS
6166 SRC 1 Ig Mag Degrees Source 1 ground current magnitude
6168 SRC 1 Ig Angle Amps Source 1 ground current angle
6169 SRC 1 I_0 Mag Degrees Source 1 zero-sequence current magnitude
6171 SRC 1 I_0 Angle Amps Source 1 zero-sequence current angle
6172 SRC 1 I_1 Mag Degrees Source 1 positive-sequence current magnitude
6174 SRC 1 I_1 Angle Amps Source 1 positive-sequence current angle
6175 SRC 1 I_2 Mag Degrees Source 1 negative-sequence current magnitude
6177 SRC 1 I_2 Angle Amps Source 1 negative-sequence current angle
6178 SRC 1 Igd Mag Degrees Source 1 differential ground current magnitude
6180 SRC 1 Igd Angle Amps Source 1 differential ground current angle
GE Multilin D60 Line Distance Protection System A-1

A.1 PARAMETER LISTS APPENDIX A
A ADDRESS
6212
FLEXANALOG NAME
SRC 2 Ic RMS
UNITS
Amps
DESCRIPTION
Source 2 phase C current RMS
A-2 D60 Line Distance Protection System GE Multilin


ADDRESS FLEXANALOG NAME UNITS DESCRIPTION A
6656 SRC 1 Vag RMS Volts Source 1 phase AG voltage RMS
6658 SRC 1 Vbg RMS Volts Source 1 phase BG voltage RMS
6660 SRC 1 Vcg RMS Volts Source 1 phase CG voltage RMS
6662 SRC 1 Vag Mag Volts Source 1 phase AG voltage magnitude
6664 SRC 1 Vag Angle Degrees Source 1 phase AG voltage angle
6665 SRC 1 Vbg Mag Volts Source 1 phase BG voltage magnitude
6667 SRC 1 Vbg Angle Degrees Source 1 phase BG voltage angle
6668 SRC 1 Vcg Mag Volts Source 1 phase CG voltage magnitude
6670 SRC 1 Vcg Angle Degrees Source 1 phase CG voltage angle
6671 SRC 1 Vab RMS Volts Source 1 phase AB voltage RMS
6673 SRC 1 Vbc RMS Volts Source 1 phase BC voltage RMS
6675 SRC 1 Vca RMS Volts Source 1 phase CA voltage RMS
6677 SRC 1 Vab Mag Volts Source 1 phase AB voltage magnitude
6679 SRC 1 Vab Angle Degrees Source 1 phase AB voltage angle
6680 SRC 1 Vbc Mag Volts Source 1 phase BC voltage magnitude
6682 SRC 1 Vbc Angle Degrees Source 1 phase BC voltage angle
6683 SRC 1 Vca Mag Volts Source 1 phase CA voltage magnitude
6685 SRC 1 Vca Angle Degrees Source 1 phase CA voltage angle
6686 SRC 1 Vx RMS Volts Source 1 auxiliary voltage RMS
6688 SRC 1 Vx Mag Volts Source 1 auxiliary voltage magnitude
6690 SRC 1 Vx Angle Degrees Source 1 auxiliary voltage angle
6691 SRC 1 V_0 Mag Volts Source 1 zero-sequence voltage magnitude
6693 SRC 1 V_0 Angle Degrees Source 1 zero-sequence voltage angle
6694 SRC 1 V_1 Mag Volts Source 1 positive-sequence voltage magnitude
6696 SRC 1 V_1 Angle Degrees Source 1 positive-sequence voltage angle
6697 SRC 1 V_2 Mag Volts Source 1 negative-sequence voltage magnitude
6699 SRC 1 V_2 Angle Degrees Source 1 negative-sequence voltage angle

A ADDRESS
6720
FLEXANALOG NAME
SRC 2 Vag RMS
UNITS
Volts
DESCRIPTION
Source 2 phase AG voltage RMS


7168 SRC 1 P Watts Source 1 three-phase real power
7170 SRC 1 Pa Watts Source 1 phase A real power
7172 SRC 1 Pb Watts Source 1 phase B real power
7174 SRC 1 Pc Watts Source 1 phase C real power
7176 SRC 1 Q Vars Source 1 three-phase reactive power
7178 SRC 1 Qa Vars Source 1 phase A reactive power
7180 SRC 1 Qb Vars Source 1 phase B reactive power
7182 SRC 1 Qc Vars Source 1 phase C reactive power
7184 SRC 1 S VA Source 1 three-phase apparent power
7186 SRC 1 Sa VA Source 1 phase A apparent power
7188 SRC 1 Sb VA Source 1 phase B apparent power
7190 SRC 1 Sc VA Source 1 phase C apparent power
7192 SRC 1 PF --- Source 1 three-phase power factor

A ADDRESS
7193
FLEXANALOG NAME
SRC 1 Phase A PF
UNITS
---
DESCRIPTION
Source 1 phase A power factor
7194 SRC 1 Phase B PF --- Source 1 phase B power factor
7195 SRC 1 Phase C PF --- Source 1 phase C power factor
7225 SRC 2 Phase A PF --- Source 2 phase A power factor


7552 SRC 1 Frequency Hz Source 1 frequency
9024 Prefault Ia Mag [0] Amps Fault 1 pre-fault phase A current magnitude
9026 Prefault Ia Ang [0] Degrees Fault 1 pre-fault phase A current angle
9027 Prefault Ib Mag [0] Amps Fault 1 pre-fault phase B current magnitude
9029 Prefault Ib Ang [0] Degrees Fault 1 pre-fault phase B current angle
9030 Prefault Ic Mag [0] Amps Fault 1 pre-fault phase C current magnitude
9032 Prefault Ic Ang [0] Degrees Fault 1 pre-fault phase C current angle
9033 Prefault Va Mag [0] Volts Fault 1 pre-fault phase A voltage magnitude
9035 Prefault Va Ang [0] Degrees Fault 1 pre-fault phase A voltage angle
9036 Prefault Vb Mag [0] Volts Fault 1 pre-fault phase B voltage magnitude
9038 Prefault Vb Ang [0] Degrees Fault 1 pre-fault phase B voltage angle
9039 Prefault Vc Mag [0] Volts Fault 1 pre-fault phase C voltage magnitude
9041 Prefault Vc Ang [0] Degrees Fault 1 pre-fault phase C voltage angle
9042 Postfault Ia Mag [0] Amps Fault 1 post-fault phase A current magnitude
9044 Postfault Ia Ang [0] Degrees Fault 1 post-fault phase A current angle
9045 Postfault Ib Mag [0] Amps Fault 1 post-fault phase B current magnitude
9047 Postfault Ib Ang [0] Degrees Fault 1 post-fault phase B current angle
9048 Postfault Ic Mag [0] Amps Fault 1 post-fault phase C current magnitude
9050 Postfault Ic Ang [0] Degrees Fault 1 post-fault phase C current angle
9051 Postfault Va Mag [0] Volts Fault 1 post-fault phase A voltage magnitude
9053 Postfault Va Ang [0] Degrees Fault 1 post-fault phase A voltage angle
9054 Postfault Vb Mag [0] Volts Fault 1 post-fault phase B voltage magnitude
9056 Postfault Vb Ang [0] Degrees Fault 1 post-fault phase B voltage angle
9057 Postfault Vc Mag [0] Volts Fault 1 post-fault phase C voltage magnitude
9059 Postfault Vc Ang [0] Degrees Fault 1 post-fault phase C voltage angle
9060 Fault Type [0] --- Fault 1 type
9061 Fault Location [0] --- Fault 1 location
9216 Synchchk 1 Delta V Volts Synchrocheck 1 delta voltage
9218 Synchchk 1 Delta F Hz Synchrocheck 1 delta frequency
9219 Synchchk 1 Delta Phs Degrees Synchrocheck 1 delta phase
9536 PMU 1 Va Mag Volts Phasor measurement unit 1 phase A voltage magnitude

A ADDRESS
9538
FLEXANALOG NAME
PMU 1 Va Angle
UNITS
Degrees
DESCRIPTION
Phasor measurement unit 1 phase A voltage angle
9539 PMU 1 Vb Mag Volts Phasor measurement unit 1 phase B voltage magnitude
9541 PMU 1 Vb Angle Degrees Phasor measurement unit 1 phase B voltage angle
9542 PMU 1 Vc Mag Volts Phasor measurement unit 1 phase C voltage magnitude
9544 PMU 1 Vc Angle Degrees Phasor measurement unit 1 phase C voltage angle
9545 PMU 1 Vx Mag Volts Phasor measurement unit 1 auxiliary voltage magnitude
9547 PMU 1 Vx Angle Degrees Phasor measurement unit 1 auxiliary voltage angle
9548 PMU 1 V1 Mag Volts Phasor measurement unit 1 positive-sequence voltage magnitude
9550 PMU 1 V1 Angle Degrees Phasor measurement unit 1 positive-sequence voltage angle
9551 PMU 1 V2 Mag Volts Phasor measurement unit 1 negative-sequence voltage magnitude
9553 PMU 1 V2 Angle Degrees Phasor measurement unit 1 negative-sequence voltage angle
9554 PMU 1 V0 Mag Volts Phasor measurement unit 1 zero-sequence voltage magnitude
9556 PMU 1 V0 Angle Degrees Phasor measurement unit 1 zero-sequence voltage angle
9557 PMU 1 Ia Mag Amps Phasor measurement unit 1 phase A current magnitude
9559 PMU 1 Ia Angle Degrees Phasor measurement unit 1 phase A current angle
9560 PMU 1 Ib Mag Amps Phasor measurement unit 1 phase B current magnitude
9562 PMU 1 Ib Angle Degrees Phasor measurement unit 1 phase B current angle
9563 PMU 1 Ic Mag Amps Phasor measurement unit 1 phase C current magnitude
9565 PMU 1 Ic Angle Degrees Phasor measurement unit 1 phase C current angle
9566 PMU 1 Ig Mag Amps Phasor measurement unit 1 ground current magnitude
9568 PMU 1 Ig Angle Degrees Phasor measurement unit 1 ground current angle
9569 PMU 1 I1 Mag Amps Phasor measurement unit 1 positive-sequence current magnitude
9571 PMU 1 I1 Angle Degrees Phasor measurement unit 1 positive-sequence current angle
9572 PMU 1 I2 Mag Amps Phasor measurement unit 1 negative-sequence current magnitude
9574 PMU 1 I2 Angle Degrees Phasor measurement unit 1 negative-sequence current angle
9575 PMU 1 I0 Mag Amps Phasor measurement unit 1 zero-sequence current magnitude
9577 PMU 1 I0 Angle Degrees Phasor measurement unit 1 zero-sequence current angle
9578 PMU 1 Freq Hz Phasor measurement unit 1 frequency
9580 PMU 1 df dt Hz/s Phasor measurement unit 1 rate of change of frequency
9581 PMU 1 Conf Ch --- Phasor measurement unit 1 configuration change counter
12306 Oscill Num Triggers --- Oscillography number of triggers
13504 DCMA Inputs 1 Value mA dcmA input 1 actual value


13552 RTD Inputs 1 Value --- RTD input 1 actual value

A ADDRESS
13591
FLEXANALOG NAME
RTD Inputs 40 Value
UNITS
---
DESCRIPTION
RTD input 40 actual value
13600 Ohm Inputs 1 Value Ohms Ohm inputs 1 value
13601 Ohm Inputs 2 Value Ohms Ohm inputs 2 value
14189 PTP–IRIG-B Delta ns PTP time minus IRIG-B time
24447 Active Setting Group --- Current setting group
32768 Tracking Frequency Hz Tracking frequency
39168 FlexElement 1 Value --- FlexElement 1 actual value
39188 FlexElement 11 Value --- FlexElemen 11 actual value
41132 VTFF 1 V0 3rd Harmonic --- V0 3rd Harmonic 1
45584 GOOSE Analog In 1 --- IEC 61850 GOOSE analog input 1


61439 PMU Num Triggers --- Phasor measurement unit recording number of triggers
A.1.2 FLEXINTEGER ITEMS
FlexInteger items are also viewable in a web browser. In the browser, enter the IP address of the UR, access the Device
Information Menu option, then the FlexInteger Parameter Listing option.
Table A–2: FLEXINTEGER DATA ITEMS
ADDRESS FLEXINTEGER NAME UNITS DESCRIPTION
9736 PMU 1 SOC seconds PMU 1 SOC timestamps
9738 PMU 1 FRACSEC seconds PMU 1 FRACSEC timestamps
9740 PMU 1 STAT --- PMU 1 STAT flags
9968 GOOSE UInt Input 1 --- IEC61850 GOOSE UInteger input 1


APPENDIX B B.1 MODBUS RTU PROTOCOL
APPENDIX B MODBUS COMMUNICATIONSB.1MODBUS RTU PROTOCOL B.1.1 INTRODUCTION
The UR-series relays support a number of communications protocols to allow connection to equipment such as personal
computers, RTUs, SCADA masters, and programmable logic controllers. The Modicon Modbus RTU protocol is the most
basic protocol supported by the UR. Modbus is available via RS232 or RS485 serial links or via ethernet (using the Mod-
bus/TCP specification). The following description is intended primarily for users who wish to develop their own master com-
munication drivers and applies to the serial Modbus RTU protocol. Note that:
• The UR always acts as a slave device, meaning that it never initiates communications; it only listens and responds to
requests issued by a master computer.
• For Modbus, a subset of the Remote Terminal Unit (RTU) protocol format is supported that allows extensive monitor-
ing, programming, and control functions using read and write register commands.
B.1.2 PHYSICAL LAYER

B
The Modbus RTU protocol is hardware-independent so that the physical layer can be any of a variety of standard hardware
configurations including RS232 and RS485. The relay includes a faceplate (front panel) RS232 port and two rear terminal
communications ports that may be configured as RS485, fiber optic, 10Base-T, or 10Base-F. Data flow is half-duplex in all
configurations. See chapter 3 for details on communications wiring.
Each data byte is transmitted in an asynchronous format consisting of 1 start bit, 8 data bits, 1 stop bit, and possibly 1 parity
bit. This produces a 10 or 11 bit data frame. This can be important for transmission through modems at high bit rates (11 bit
data frames are not supported by many modems at baud rates greater than 300).
The baud rate and parity are independently programmable for each communications port. Baud rates of 300, 1200, 2400,
4800, 9600, 14400, 19200, 28800, 33600, 38400, 57600, or 115200 bps are available. Even, odd, and no parity are avail-
able. Refer to the Communications section of chapter 5 for further details.
The master device in any system must know the address of the slave device with which it is to communicate. The relay will
not act on a request from a master if the address in the request does not match the relay’s slave address (unless the
address is the broadcast address – see below).
A single setting selects the slave address used for all ports, with the exception that for the faceplate port, the relay will
accept any address when the Modbus RTU protocol is used.
B.1.3 DATA LINK LAYER
Communications takes place in packets which are groups of asynchronously framed byte data. The master transmits a
packet to the slave and the slave responds with a packet. The end of a packet is marked by dead-time on the communica-
tions line. The following describes general format for both transmit and receive packets. For exact details on packet format-
ting, refer to subsequent sections describing each function code.
Table B–1: MODBUS PACKET FORMAT

DESCRIPTION SIZE
SLAVE ADDRESS 1 byte
FUNCTION CODE 1 byte
DATA N bytes
CRC 2 bytes
DEAD TIME 3.5 bytes transmission time
• SLAVE ADDRESS: This is the address of the slave device that is intended to receive the packet sent by the master
and to perform the desired action. Each slave device on a communications bus must have a unique address to prevent
bus contention. All of the relay’s ports have the same address which is programmable from 1 to 254; see chapter 5 for
details. Only the addressed slave will respond to a packet that starts with its address. Note that the faceplate port is an
exception to this rule; it will act on a message containing any slave address.
A master transmit packet with slave address 0 indicates a broadcast command. All slaves on the communication link
take action based on the packet, but none respond to the master. Broadcast mode is only recognized when associated
with function code 05h. For any other function code, a packet with broadcast mode slave address 0 will be ignored.
GE Multilin D60 Line Distance Protection System B-1

B.1 MODBUS RTU PROTOCOL APPENDIX B
• FUNCTION CODE: This is one of the supported functions codes of the unit which tells the slave what action to per-
form. See the Supported Function Codes section for complete details. An exception response from the slave is indi-
cated by setting the high order bit of the function code in the response packet. See the Exception Responses section
for further details.
• DATA: This will be a variable number of bytes depending on the function code. This may include actual values, set-
tings, or addresses sent by the master to the slave or by the slave to the master.
• CRC: This is a two byte error checking code. The RTU version of Modbus includes a 16-bit cyclic redundancy check
(CRC-16) with every packet which is an industry standard method used for error detection. If a Modbus slave device
receives a packet in which an error is indicated by the CRC, the slave device will not act upon or respond to the packet
thus preventing any erroneous operations. See the CRC-16 Algorithm section for details on calculating the CRC.
• DEAD TIME: A packet is terminated when no data is received for a period of 3.5 byte transmission times (about 15 ms
at 2400 bps, 2 ms at 19200 bps, and 300 µs at 115200 bps). Consequently, the transmitting device must not allow gaps
B between bytes longer than this interval. Once the dead time has expired without a new byte transmission, all slaves
start listening for a new packet from the master except for the addressed slave.
B.1.4 CRC-16 ALGORITHM
The CRC-16 algorithm essentially treats the entire data stream (data bits only; start, stop and parity ignored) as one contin-
uous binary number. This number is first shifted left 16 bits and then divided by a characteristic polynomial
(11000000000000101B). The 16-bit remainder of the division is appended to the end of the packet, MSByte first. The
resulting packet including CRC, when divided by the same polynomial at the receiver will give a zero remainder if no trans-
mission errors have occurred. This algorithm requires the characteristic polynomial to be reverse bit ordered. The most sig-
nificant bit of the characteristic polynomial is dropped, since it does not affect the value of the remainder.
A C programming language implementation of the CRC algorithm will be provided upon request.
Table B–2: CRC-16 ALGORITHM

SYMBOLS: --> data transfer
A 16 bit working register
Alow low order byte of A
Ahigh high order byte of A
CRC 16 bit CRC-16 result
i,j loop counters
(+) logical EXCLUSIVE-OR operator
N total number of data bytes
Di i-th data byte (i = 0 to N-1)
G 16 bit characteristic polynomial = 1010000000000001 (binary) with MSbit dropped and bit order reversed
shr (x) right shift operator (th LSbit of x is shifted into a carry flag, a '0' is shifted into the MSbit of x, all other bits
are shifted right one location)
ALGORITHM: 1. FFFF (hex) --> A

2. 0 --> i
3. 0 --> j
4. Di (+) Alow --> Alow
5. j + 1 --> j
6. shr (A)
7. Is there a carry? No: go to 8; Yes: G (+) A --> A and continue.
8. Is j = 8? No: go to 5; Yes: continue
9. i + 1 --> i
10. Is i = N? No: go to 3; Yes: continue
11. A --> CRC
B-2 D60 Line Distance Protection System GE Multilin

APPENDIX B B.2 MODBUS FUNCTION CODES
B.2MODBUS FUNCTION CODES B.2.1 SUPPORTED FUNCTION CODES
Modbus officially defines function codes from 1 to 127 though only a small subset is generally needed. The relay supports
some of these functions, as summarized in the following table. Subsequent sections describe each function code in detail.
FUNCTION CODE MODBUS DEFINITION GE MULTILIN DEFINITION

HEX DEC
03 3 Read holding registers Read actual values or settings
04 4 Read holding registers Read actual values or settings
05 5 Force single coil Execute operation
06 6 Preset single register Store single setting
10 16 Preset multiple registers Store multiple settings
B
B.2.2 READ ACTUAL VALUES OR SETTINGS (FUNCTION CODE 03/04H)
This function code allows the master to read one or more consecutive data registers (actual values or settings) from a relay.
Data registers are always 16-bit (two-byte) values transmitted with high order byte first. The maximum number of registers
that can be read in a single packet is 125. See the Modbus memory map table for exact details on the data registers.
Since some PLC implementations of Modbus only support one of function codes 03h and 04h. The D60 interpretation
allows either function code to be used for reading one or more consecutive data registers. The data starting address will
determine the type of data being read. Function codes 03h and 04h are therefore identical.
The following table shows the format of the master and slave packets. The example shows a master device requesting
three register values starting at address 4050h from slave device 11h (17 decimal); the slave device responds with the val-
ues 40, 300, and 0 from registers 4050h, 4051h, and 4052h, respectively.
Table B–3: MASTER AND SLAVE DEVICE PACKET TRANSMISSION EXAMPLE

MASTER TRANSMISSION SLAVE RESPONSE
PACKET FORMAT EXAMPLE (HEX) PACKET FORMAT EXAMPLE (HEX)
SLAVE ADDRESS 11 SLAVE ADDRESS 11
FUNCTION CODE 04 FUNCTION CODE 04
DATA STARTING ADDRESS - high 40 BYTE COUNT 06
DATA STARTING ADDRESS - low 50 DATA #1 - high 00
NUMBER OF REGISTERS - high 00 DATA #1 - low 28
NUMBER OF REGISTERS - low 03 DATA #2 - high 01
CRC - low A7 DATA #2 - low 2C
CRC - high 4A DATA #3 - high 00
DATA #3 - low 00
CRC - low 0D
CRC - high 60

B.2 MODBUS FUNCTION CODES APPENDIX B
B.2.3 EXECUTE OPERATION (FUNCTION CODE 05H)
This function code allows the master to perform various operations in the relay. Available operations are shown in the Sum-
mary of operation codes table below.
The following table shows the format of the master and slave packets. The example shows a master device requesting the
slave device 11h (17 decimal) to perform a reset. The high and low code value bytes always have the values “FF” and “00”
respectively and are a remnant of the original Modbus definition of this function code.

B FUNCTION CODE 05 FUNCTION CODE 05
OPERATION CODE - high 00 OPERATION CODE - high 00
OPERATION CODE - low 01 OPERATION CODE - low 01
CODE VALUE - high FF CODE VALUE - high FF
CODE VALUE - low 00 CODE VALUE - low 00
CRC - low DF CRC - low DF
CRC - high 6A CRC - high 6A
Table B–5: SUMMARY OF OPERATION CODES FOR FUNCTION 05H

OPERATION DEFINITION DESCRIPTION
CODE (HEX)
0000 NO OPERATION Does not do anything.
0001 RESET Performs the same function as the faceplate RESET key.
0005 CLEAR EVENT RECORDS Performs the same function as the faceplate CLEAR EVENT RECORDS menu
command.
0006 CLEAR OSCILLOGRAPHY Clears all oscillography records.
1000 to 103F VIRTUAL IN 1 to 64 ON/OFF Sets the states of Virtual Inputs 1 to 64 either “ON” or “OFF”.
B.2.4 STORE SINGLE SETTING (FUNCTION CODE 06H)
This function code allows the master to modify the contents of a single setting register in an relay. Setting registers are
always 16 bit (two byte) values transmitted high order byte first. The following table shows the format of the master and
slave packets. The example shows a master device storing the value 200 at memory map address 4051h to slave device
11h (17 dec).

FUNCTION CODE 06 FUNCTION CODE 06
DATA STARTING ADDRESS - high 40 DATA STARTING ADDRESS - high 40
DATA STARTING ADDRESS - low 51 DATA STARTING ADDRESS - low 51
DATA - high 00 DATA - high 00
DATA - low C8 DATA - low C8
CRC - low CE CRC - low CE
CRC - high DD CRC - high DD

APPENDIX B B.2 MODBUS FUNCTION CODES
B.2.5 STORE MULTIPLE SETTINGS (FUNCTION CODE 10H)
This function code allows the master to modify the contents of a one or more consecutive setting registers in a relay. Setting
registers are 16-bit (two byte) values transmitted high order byte first. The maximum number of setting registers that can be
stored in a single packet is 60. The following table shows the format of the master and slave packets. The example shows
a master device storing the value 200 at memory map address 4051h, and the value 1 at memory map address 4052h to
slave device 11h (17 decimal).

FUNCTION CODE 10 FUNCTION CODE 10 B
DATA STARTING ADDRESS - hi 40 DATA STARTING ADDRESS - hi 40
DATA STARTING ADDRESS - lo 51 DATA STARTING ADDRESS - lo 51
NUMBER OF SETTINGS - hi 00 NUMBER OF SETTINGS - hi 00
NUMBER OF SETTINGS - lo 02 NUMBER OF SETTINGS - lo 02
BYTE COUNT 04 CRC - lo 07
DATA #1 - high order byte 00 CRC - hi 64
DATA #1 - low order byte C8
DATA #2 - high order byte 00
DATA #2 - low order byte 01
CRC - low order byte 12
CRC - high order byte 62
B.2.6 EXCEPTION RESPONSES
Programming or operation errors usually happen because of illegal data in a packet. These errors result in an exception
response from the slave. The slave detecting one of these errors sends a response packet to the master with the high order
bit of the function code set to 1.
The following table shows the format of the master and slave packets. The example shows a master device sending the
unsupported function code 39h to slave device 11.

FUNCTION CODE 39 FUNCTION CODE B9
CRC - low order byte CD ERROR CODE 01
CRC - high order byte F2 CRC - low order byte 93
CRC - high order byte 95

B.3 FILE TRANSFERS APPENDIX B
B.3FILE TRANSFERS B.3.1 OBTAINING RELAY FILES VIA MODBUS
a) DESCRIPTION
The UR relay has a generic file transfer facility, meaning that you use the same method to obtain all of the different types of
files from the unit. The Modbus registers that implement file transfer are found in the "Modbus File Transfer (Read/Write)"
and "Modbus File Transfer (Read Only)" modules, starting at address 3100 in the Modbus Memory Map. To read a file from
the UR relay, use the following steps:
1. Write the filename to the "Name of file to read" register using a write multiple registers command. If the name is shorter
than 80 characters, you may write only enough registers to include all the text of the filename. Filenames are not case
sensitive.
2. Repeatedly read all the registers in "Modbus File Transfer (Read Only)" using a read multiple registers command. It is
not necessary to read the entire data block, since the UR relay will remember which was the last register you read. The
B "position" register is initially zero and thereafter indicates how many bytes (2 times the number of registers) you have
read so far. The "size of..." register indicates the number of bytes of data remaining to read, to a maximum of 244.
3. Keep reading until the "size of..." register is smaller than the number of bytes you are transferring. This condition indi-
cates end of file. Discard any bytes you have read beyond the indicated block size.
4. If you need to re-try a block, read only the "size of.." and "block of data", without reading the position. The file pointer is
only incremented when you read the position register, so the same data block will be returned as was read in the pre-
vious operation. On the next read, check to see if the position is where you expect it to be, and discard the previous
block if it is not (this condition would indicate that the UR relay did not process your original read request).
The UR relay retains connection-specific file transfer information, so files may be read simultaneously on multiple Modbus
connections.
b) OTHER PROTOCOLS
All the files available via Modbus may also be retrieved using the standard file transfer mechanisms in other protocols (for
example, TFTP or MMS).
c) COMTRADE, OSCILLOGRAPHY, AND DATA LOGGER FILES

Oscillography and data logger files are formatted using the COMTRADE file format per IEEE C37.111-1999 Standard Com-
mon Format for Transient Data Exchange (COMTRADE) for Power Systems. The files can be obtained in either text or
binary COMTRADE format.
d) READING OSCILLOGRAPHY FILES

Familiarity with the oscillography feature is required to understand the following description. Refer to the Oscillography sec-
tion in Chapter 5 for additional details.
The Oscillography Number of Triggers register is incremented by one every time a new oscillography file is triggered (cap-
tured) and cleared to zero when oscillography data is cleared. When a new trigger occurs, the associated oscillography file
is assigned a file identifier number equal to the incremented value of this register; the newest file number is equal to the
Oscillography_Number_of_Triggers register. This register can be used to determine if any new data has been captured by
periodically reading it to see if the value has changed; if the number has increased then new data is available.
The Oscillography Number of Records register specifies the maximum number of files (and the number of cycles of data
per file) that can be stored in memory of the relay. The Oscillography Available Records register specifies the actual num-
ber of files that are stored and still available to be read out of the relay.
Writing “Yes” (i.e. the value 1) to the Oscillography Clear Data register clears oscillography data files, clears both the Oscil-
lography Number of Triggers and Oscillography Available Records registers to zero, and sets the Oscillography Last
Cleared Date to the present date and time.
To read binary COMTRADE oscillography files, read the following filenames:
OSCnnnn.CFG and OSCnnn.DAT
Replace “nnn” with the desired oscillography trigger number. For ASCII format, use the following file names
OSCAnnnn.CFG and OSCAnnn.DAT

APPENDIX B B.3 FILE TRANSFERS
e) READING DATA LOGGER FILES

Familiarity with the data logger feature is required to understand this description. Refer to the Data Logger section of Chap-
ter 5 for details. To read the entire data logger in binary COMTRADE format, read the following files.
datalog.cfg and datalog.dat
To read the entire data logger in ASCII COMTRADE format, read the following files.
dataloga.cfg and dataloga.dat
To limit the range of records to be returned in the COMTRADE files, append the following to the filename before writing it:
• To read from a specific time to the end of the log: <space> startTime
• To read a specific range of records: <space> startTime <space> endTime
• Replace <startTime> and <endTime> with Julian dates (seconds since Jan. 1 1970) as numeric text.
f) READING EVENT RECORDER FILES

B
To read the entire event recorder contents in ASCII format (the only available format), use the following filename:
EVT.TXT
To read from a specific record to the end of the log, use the following filename:
EVTnnn.TXT (replace nnn with the desired starting record number)
To read from a specific record to another specific record, use the following filename:
EVT.TXT xxxxx yyyyy (replace xxxxx with the starting record number and yyyyy with the ending record number)
g) READING FAULT REPORT FILES

Fault report data has been available via the D60 file retrieval mechanism since UR firmware version 2.00. The file name is
faultReport#####.htm. The ##### refers to the fault report record number. The fault report number is a counter that
indicates how many fault reports have ever occurred. The counter rolls over at a value of 65535. Only the last ten fault
reports are available for retrieval; a request for a non-existent fault report file will yield a null file. The current value fault
report counter is available in “Number of Fault Reports” Modbus register at location 0x3020.
For example, if 14 fault reports have occurred then the files faultReport5.htm, faultReport6.htm, up to
faultReport14.htm are available to be read. The expected use of this feature has an external master periodically poll-
ing the “Number of Fault Reports' register. If the value changes, then the master reads all the new files.
The contents of the file is in standard HTML notation and can be viewed via any commercial browser.
B.3.2 MODBUS PASSWORD OPERATION

and the faceplate RS232 connection. Remote access is defined as any access to settings or commands via any rear com-
munications port. This includes both Ethernet and RS485 connections. Any changes to the local or remote passwords
is to the RS232 port of the faceplate, the local password must be used.
The command password is set up at memory location 4000. Command security is required to change the command pass-
word. Similarly, the setting password is set up at memory location 4002. These are the same settings found in the SETTINGS
 PRODUCT SETUP  PASSWORD SECURITY menu via the keypad. Enabling password security for the faceplate display will
also enable it for Modbus, and vice-versa.
To gain command level security access, the command password must be entered at memory location 4008. To gain setting
level security access, the setting password must be entered at memory location 400A. The entered setting password must
match the current setting password setting, or must be zero, to change settings or download firmware.

B.3 FILE TRANSFERS APPENDIX B
Command and setting passwords each have a 30 minute timer. Each timer starts when you enter the particular password,
and is re-started whenever you use it. For example, writing a setting re-starts the setting password timer and writing a com-
mand register or forcing a coil re-starts the command password timer. The value read at memory location 4010 can be used
to confirm whether a command password is enabled or disabled (a value of 0 represents disabled). The value read at mem-
ory location 4011 can be used to confirm whether a setting password is enabled or disabled.
Command or setting password security access is restricted to the particular port or particular TCP/IP connection on which
the entry was made. Passwords must be entered when accessing the relay through other ports or connections, and the
passwords must be re-entered after disconnecting and re-connecting on TCP/IP.

APPENDIX B B.4 MEMORY MAPPING
B.4MEMORY MAPPING B.4.1 MODBUS MEMORY MAP
The map is also viewable in a web browser. In the browser, enter the IP address of the UR and click the option.
Table B–9: MODBUS MEMORY MAP (Sheet 1 of 72)

ADDR REGISTER NAME RANGE UNITS STEP FORMAT DEFAULT
Product Information (Read Only)
0000 UR Product Type 0 to 65535 --- 1 F001 0
0002 Product Version 0 to 655.35 --- 0.01 F001 1
0003 Boot Configuration Register 0 to 65535 --- 1 F001 0
Product Information (Read Only -- Written by Factory)
0010 Serial Number --- --- --- F203 “0”
0020
0022
Manufacturing Date
Modification Number
0 to 4294967295
0 to 65535
---
---
1
1
F050
F001
0
0
B
0040 Order Code --- --- --- F204 “Order Code x”
0090 Ethernet MAC Address --- --- --- F072 0
0093 Reserved (13 items) --- --- --- F001 0
00A0 CPU Module Serial Number --- --- --- F203 (none)
00B0 CPU Supplier Serial Number --- --- --- F203 (none)
00C0 Ethernet Sub Module Serial Number (8 items) --- --- --- F203 (none)
Product Information (Read Only -- Written by Factory)
0110 FPGA Version --- --- --- F206 (none)
0113 FPGA Date 0 to 4294967295 -- 1 F050 0
Self Test Targets (Read Only)
0200 Self Test States (4 items) 0 to 4294967295 0 1 F143 0
Front Panel (Read Only)
0208 LED Column n State, n = 1 to 10 (10 items) 0 to 65535 --- 1 F501 0
0220 Display Message --- --- --- F204 (none)
0248 Last Key Pressed 0 to 47 --- 1 F530 0 (None)
Keypress Emulation (Read/Write)
0280 Simulated keypress -- write zero before each keystroke 0 to 46 --- 1 F190 0 (No key -- use
between real
keys)
Virtual Input Commands (Read/Write Command) (64 modules)
0400 Virtual Input 1 State 0 to 1 --- 1 F108 0 (Off)
040A Virtual Input 11 State 0 to 1 --- 1 F108 0 (Off)
040B Virtual Input 12 State 0 to 1 --- 1 F108 0 (Off)
040C Virtual Input 13 State 0 to 1 --- 1 F108 0 (Off)
040D Virtual Input 14 State 0 to 1 --- 1 F108 0 (Off)
040E Virtual Input 15 State 0 to 1 --- 1 F108 0 (Off)
040F Virtual Input 16 State 0 to 1 --- 1 F108 0 (Off)

B.4 MEMORY MAPPING APPENDIX B

B
Digital Counter States (Read Only Non-Volatile) (8 modules)
0800 Digital Counter 1 Value -2147483647 to --- 1 F004 0
2147483647
0802 Digital Counter 1 Frozen -2147483647 to --- 1 F004 0
2147483647
0804 Digital Counter 1 Frozen Time Stamp 0 to 4294967295 --- 1 F050 0
0806 Digital Counter 1 Frozen Time Stamp us 0 to 4294967295 --- 1 F003 0
0808 ...Repeated for Digital Counter 2


FlexStates (Read Only)
0900 FlexState Bits (16 items) 0 to 65535 --- 1 F001 0
Element States (Read Only)
1000 Element Operate States (64 items) 0 to 65535 --- 1 F502 0
User Displays Actuals (Read Only)
1080 Formatted user-definable displays (16 items) --- --- --- F200 (none)
Modbus User Map Actuals (Read Only)
1200 User Map Values (256 items) 0 to 65535 --- 1 F001 0
Element Targets (Read Only)
14E0 Target Sequence 0 to 65535 --- 1 F001 0
14E1 Number of Targets 0 to 65535 --- 1 F001 0 B
Element Targets (Read/Write)
14E2 Target to Read 0 to 65535 --- 1 F001 0
Element Targets (Read Only)
14E3 Target Message --- --- --- F200 “.”
Digital Input/Output States (Read Only)
1500 Contact Input States (6 items) 0 to 65535 --- 1 F500 0
1508 Virtual Input States (8 items) 0 to 65535 --- 1 F500 0
1510 Contact Output States (4 items) 0 to 65535 --- 1 F500 0
1518 Contact Output Current States (4 items) 0 to 65535 --- 1 F500 0
1520 Contact Output Voltage States (4 items) 0 to 65535 --- 1 F500 0
1528 Virtual Output States (6 items) 0 to 65535 --- 1 F500 0
1530 Contact Output Detectors (4 items) 0 to 65535 --- 1 F500 0
Input/Output States (Read Only)
1540 Remote Device States (2 items) 0 to 65535 --- 1 F500 0
1542 Remote Input States (4 items) 0 to 65535 --- 1 F500 0
1550 Remote Devices Online 0 to 1 --- 1 F126 0 (No)
1551 Remote Double-Point Status Input 1 State 0 to 3 --- 1 F605 3 (Bad)
Platform Direct Input/Output States (Read Only)
15C0 Direct input states (6 items) 0 to 65535 --- 1 F500 0
15C8 Direct outputs average message return time 1 0 to 65535 ms 1 F001 0
15C9 Direct outputs average message return time 2 0 to 65535 ms 1 F001 0
15CA Direct inputs/outputs unreturned message count - Ch. 1 0 to 65535 --- 1 F001 0
15CB Direct inputs/outputs unreturned message count - Ch. 2 0 to 65535 --- 1 F001 0
15D0 Direct device states 0 to 65535 --- 1 F500 0
15D1 Reserved 0 to 65535 --- 1 F001 0
15D2 Direct inputs/outputs CRC fail count 1 0 to 65535 --- 1 F001 0
15D3 Direct inputs/outputs CRC fail count 2 0 to 65535 --- 1 F001 0
Field Unit Input/Output States (Read Only)
15E0 Field unit contact input states (3 items) 0 to 65535 --- 1 F500 0
15E3 Field unit contact input output operand states (8 items) 0 to 65535 --- 1 F500 0
15EB Field contact output physical states (8 items) 0 to 65535 --- 1 F500 0
15F3 Field contact output current states (8 items) 0 to 65535 --- 1 F500 0
15FB Field contact output physical states (8 items) 0 to 65535 --- 1 F500 0
1603 Field shared input states 0 to 65535 --- 1 F500 0
1604 Field shared input channel states 0 to 65535 --- 1 F500 0
1605 Field shared input test states 0 to 65535 --- 1 F500 0
1606 Field shared output operand states 0 to 65535 --- 1 F500 0
1607 Field latching output open operand states 0 to 65535 --- 1 F500 0


1608 Field latching output close operand states 0 to 65535 --- 1 F500 0
1609 Field latching output open driver states 0 to 65535 --- 1 F500 0
160A Field latching output close driver states 0 to 65535 --- 1 F500 0
160B Field latching output physical states 0 to 65535 --- 1 F500 0
160C Field unit online/offline states 0 to 65535 --- 1 F500 0
160D Fiedl RTD input trouble states 0 to 65535 --- 1 F500 0
160E Field transducer input trouble states 0 to 65535 --- 1 F500 0
Ethernet Fibre Channel Status (Read/Write)
1610 Ethernet primary fibre channel status 0 to 2 --- 1 F134 0 (Fail)
1611 Ethernet secondary fibre channel status 0 to 2 --- 1 F134 0 (Fail)
B
1612 Ethernet tertiary fibre channel status 0 to 2 --- 1 F134 0 (Fail)
Data Logger Actuals (Read Only)
1618 Data logger channel count 0 to 16 channel 1 F001 0
1619 Time of oldest available samples 0 to 4294967295 seconds 1 F050 0
161B Time of newest available samples 0 to 4294967295 seconds 1 F050 0
161D Data logger duration 0 to 999.9 days 0.1 F001 0
Sensitive Directional Power Actuals (Read Only) (2 modules)
1680 Sensitive Directional Power 1 Power -2147483647 to 2147483647 W 1 F060 0
1682 Sensitive Directional Power 2 Power -2147483647 to 2147483647 W 1 F060 0
Field Unit RTD Actuals (Read Only) (8 modules)
16C0 Field RTD x Value -32768 to 32767 °C 1 F002 0
16C1 ...Repeated for module number 2
Field Unit Transducer Actuals (Read Only) (8 modules)
16C8 Field Transducer x Value -32.768 to 32.767 --- 0.001 F004 0
16CA ...Repeated for module number 2
16CC ...Repeated for module number 3
16CE ...Repeated for module number 4
16D0 ...Repeated for module number 5
Frequency Rate of Change Actuals (Read Only) (4 modules)
16E0 Frequency Rate of Change 1 -327.67 to 327.67 Hz/s 0.01 F002 0
16E1 Reserved (3 items) 0 to 65535 --- 1 F001 0
16E4 ...Repeated for Frequency Rate of Change 2
16E8 ...Repeated for Frequency Rate of Change 3
16EC ...Repeated for Frequency Rate of Change 4
Source Current (Read Only) (6 modules)
1800 Source 1 Phase A Current RMS 0 to 999999.999 A 0.001 F060 0
1802 Source 1 Phase B Current RMS 0 to 999999.999 A 0.001 F060 0
1804 Source 1 Phase C Current RMS 0 to 999999.999 A 0.001 F060 0
1806 Source 1 Neutral Current RMS 0 to 999999.999 A 0.001 F060 0
1808 Source 1 Phase A Current Magnitude 0 to 999999.999 A 0.001 F060 0
180A Source 1 Phase A Current Angle -359.9 to 0 degrees 0.1 F002 0
180B Source 1 Phase B Current Magnitude 0 to 999999.999 A 0.001 F060 0
180D Source 1 Phase B Current Angle -359.9 to 0 degrees 0.1 F002 0
180E Source 1 Phase C Current Magnitude 0 to 999999.999 A 0.001 F060 0
1810 Source 1 Phase C Current Angle -359.9 to 0 degrees 0.1 F002 0


1811 Source 1 Neutral Current Magnitude 0 to 999999.999 A 0.001 F060 0
1813 Source 1 Neutral Current Angle -359.9 to 0 degrees 0.1 F002 0
1814 Source 1 Ground Current RMS 0 to 999999.999 A 0.001 F060 0
1816 Source 1 Ground Current Magnitude 0 to 999999.999 A 0.001 F060 0
1818 Source 1 Ground Current Angle -359.9 to 0 degrees 0.1 F002 0
1819 Source 1 Zero Sequence Current Magnitude 0 to 999999.999 A 0.001 F060 0
181B Source 1 Zero Sequence Current Angle -359.9 to 0 degrees 0.1 F002 0
181C Source 1 Positive Sequence Current Magnitude 0 to 999999.999 A 0.001 F060 0
181E Source 1 Positive Sequence Current Angle -359.9 to 0 degrees 0.1 F002 0
181F Source 1 Negative Sequence Current Magnitude 0 to 999999.999 A 0.001 F060 0
1821 Source 1 Negative Sequence Current Angle -359.9 to 0 degrees 0.1 F002 0
1822 Source 1 Differential Ground Current Magnitude 0 to 999999.999 A 0.001 F060 0 B
1824 Source 1 Differential Ground Current Angle -359.9 to 0 degrees 0.1 F002 0
1825 Reserved (27 items) --- --- --- F001 0
1840 ...Repeated for Source 2
18C0 ...Repeated for Source 4
Source Voltage (Read Only) (6 modules)
1A00 Source 1 Phase AG Voltage RMS 0 to 999999.999 V 0.001 F060 0
1A02 Source 1 Phase BG Voltage RMS 0 to 999999.999 V 0.001 F060 0
1A04 Source 1 Phase CG Voltage RMS 0 to 999999.999 V 0.001 F060 0
1A06 Source 1 Phase AG Voltage Magnitude 0 to 999999.999 V 0.001 F060 0
1A08 Source 1 Phase AG Voltage Angle -359.9 to 0 degrees 0.1 F002 0
1A09 Source 1 Phase BG Voltage Magnitude 0 to 999999.999 V 0.001 F060 0
1A0B Source 1 Phase BG Voltage Angle -359.9 to 0 degrees 0.1 F002 0
1A0C Source 1 Phase CG Voltage Magnitude 0 to 999999.999 V 0.001 F060 0
1A0E Source 1 Phase CG Voltage Angle -359.9 to 0 degrees 0.1 F002 0
1A0F Source 1 Phase AB or AC Voltage RMS 0 to 999999.999 V 0.001 F060 0
1A11 Source 1 Phase BC or BA Voltage RMS 0 to 999999.999 V 0.001 F060 0
1A13 Source 1 Phase CA or CB Voltage RMS 0 to 999999.999 V 0.001 F060 0
1A15 Source 1 Phase AB or AC Voltage Magnitude 0 to 999999.999 V 0.001 F060 0
1A17 Source 1 Phase AB or AC Voltage Angle -359.9 to 0 degrees 0.1 F002 0
1A18 Source 1 Phase BC or BA Voltage Magnitude 0 to 999999.999 V 0.001 F060 0
1A1A Source 1 Phase BC or BA Voltage Angle -359.9 to 0 degrees 0.1 F002 0
1A1B Source 1 Phase CA or CB Voltage Magnitude 0 to 999999.999 V 0.001 F060 0
1A1D Source 1 Phase CA or CB Voltage Angle -359.9 to 0 degrees 0.1 F002 0
1A1E Source 1 Auxiliary Voltage RMS V F060 0
1A20 Source 1 Auxiliary Voltage Magnitude 0 to 999999.999 V 0.001 F060 0
1A22 Source 1 Auxiliary Voltage Angle -359.9 to 0 degrees 0.1 F002 0
1A23 Source 1 Zero Sequence Voltage Magnitude 0 to 999999.999 V 0.001 F060 0
1A25 Source 1 Zero Sequence Voltage Angle -359.9 to 0 degrees 0.1 F002 0
1A26 Source 1 Positive Sequence Voltage Magnitude 0 to 999999.999 V 0.001 F060 0
1A28 Source 1 Positive Sequence Voltage Angle -359.9 to 0 degrees 0.1 F002 0
1A29 Source 1 Negative Sequence Voltage Magnitude 0 to 999999.999 V 0.001 F060 0
1A2B Source 1 Negative Sequence Voltage Angle -359.9 to 0 degrees 0.1 F002 0
1A2C Reserved (20 items) --- --- --- F001 0
1A40 ...Repeated for Source 2
1AC0 ...Repeated for Source 4
1B00 ...Repeated for Source 5
1B40 ...Repeated for Source 6


Source Power (Read Only) (6 modules)
1C00 Source 1 Three Phase Real Power -1000000000000 to W 0.001 F060 0
1000000000000
1C02 Source 1 Phase A Real Power -1000000000000 to W 0.001 F060 0
1000000000000
1C04 Source 1 Phase B Real Power -1000000000000 to W 0.001 F060 0
1000000000000
1C06 Source 1 Phase C Real Power -1000000000000 to W 0.001 F060 0
1000000000000
1C08 Source 1 Three Phase Reactive Power -1000000000000 to var 0.001 F060 0
1000000000000
1C0A Source 1 Phase A Reactive Power -1000000000000 to var 0.001 F060 0
1000000000000
B 1C0C Source 1 Phase B Reactive Power -1000000000000 to

1000000000000
var 0.001 F060 0
1C0E Source 1 Phase C Reactive Power -1000000000000 to var 0.001 F060 0

1000000000000
1C10 Source 1 Three Phase Apparent Power -1000000000000 to VA 0.001 F060 0
1000000000000
1C12 Source 1 Phase A Apparent Power -1000000000000 to VA 0.001 F060 0
1000000000000
1C14 Source 1 Phase B Apparent Power -1000000000000 to VA 0.001 F060 0
1000000000000
1C16 Source 1 Phase C Apparent Power -1000000000000 to VA 0.001 F060 0
1000000000000
1C18 Source 1 Three Phase Power Factor -0.999 to 1 --- 0.001 F013 0
1C19 Source 1 Phase A Power Factor -0.999 to 1 --- 0.001 F013 0
1C1A Source 1 Phase B Power Factor -0.999 to 1 --- 0.001 F013 0
1C1B Source 1 Phase C Power Factor -0.999 to 1 --- 0.001 F013 0
1C1C Reserved (4 items) --- --- --- F001 0
1CA0 ...Repeated for Source 6
Source Energy (Read Only Non-Volatile) (6 modules)
1D00 Source 1 Positive Watthour 0 to 1000000000000 Wh 0.001 F060 0
1D02 Source 1 Negative Watthour 0 to 1000000000000 Wh 0.001 F060 0
1D04 Source 1 Positive Varhour 0 to 1000000000000 varh 0.001 F060 0
1D06 Source 1 Negative Varhour 0 to 1000000000000 varh 0.001 F060 0
1D08 Reserved (8 items) --- --- --- F001 0
1D10 ...Repeated for Source 2
Energy Commands (Read/Write Command)
1D60 Energy Clear Command 0 to 1 --- 1 F126 0 (No)
Source Frequency (Read Only) (6 modules)
1D80 Frequency for Source 1 2 to 90 Hz 0.001 F003 0
1D8A Frequency for Source 6 2 to 90 Hz 0.001 F003 0
Breaker Flashover (Read/Write Setting) (2 modules)
2196 Breaker flashover 1 function 0 to 1 --- 1 F102 0 (Disabled)
2197 Breaker flashover 1 side 1 source 0 to 5 --- 1 F167 0 (SRC 1)


2198 Breaker flashover 1 side 2 source 0 to 6 --- 1 F211 0 (None)
2199 Breaker flashover 1 status closed A 0 to 4294967295 --- 1 F300 0
219B Breaker flashover 1 status closed B 0 to 4294967295 --- 1 F300 0
219D Breaker flashover 1 status closed C 0 to 4294967295 --- 1 F300 0
219F Breaker flashover 1 voltage pickup level 0 to 1.5 pu 0.001 F001 850
21A0 Breaker flashover 1 voltage difference pickup level 0 to 100000 V 1 F060 1000
21A2 Breaker flashover 1 current pickup level 0 to 1.5 pu 0.001 F001 600
21A3 Breaker flashover 1 pickup delay 0 to 65.535 s 0.001 F001 100
21A4 Breaker flashover 1 supervision phase A 0 to 4294967295 --- 1 F300 0
21A6 Breaker flashover 1 supervision phase B 0 to 4294967295 --- 1 F300 0
21A8 Breaker flashover 1 supervision phase C 0 to 4294967295 --- 1 F300 0
21AA Breaker flashover 1 block 0 to 4294967295 --- 1 F300 0 B
21AC Breaker flashover 1 events 0 to 1 --- 1 F102 0 (Disabled)
21AD Breaker flashover 1 target 0 to 2 --- 1 F109 0 (Self-Reset)
21AE Reserved (4 items) --- --- --- F001 0
21B2 ...Repeated for breaker flashover 2
Breaker Arcing Current Actuals (Read Only Non-Volatile) (6 modules)
21E0 Breaker 1 Arcing Current Phase A 0 to 99999999 kA2-cyc 1 F060 0
21E2 Breaker 1 Arcing Current Phase B 0 to 99999999 kA2-cyc 1 F060 0
21E4 Breaker 1 Arcing Current Phase C 0 to 99999999 kA2-cyc 1 F060 0
21E6 Breaker 1 Operating Time Phase A 0 to 65535 ms 1 F001 0
21E7 Breaker 1 Operating Time Phase B 0 to 65535 ms 1 F001 0
21E8 Breaker 1 Operating Time Phase C 0 to 65535 ms 1 F001 0
21E9 Breaker 1 Operating Time 0 to 65535 ms 1 F001 0
21EA ...Repeated for module number 2
21EE ...Repeated for module number 2
21F0 ...Repeated for module number 2
21F2 ...Repeated for module number 2
21FA ...Repeated for module number 3
21FE ...Repeated for module number 4
2208 ...Repeated for module number 5
Breaker Arcing Current Commands (Read/Write Command) (6 modules)
2224 Breaker 1 Arcing Current Clear Command 0 to 1 --- 1 F126 0 (No)
Passwords Unauthorized Access (Read/Write Command)
2230 Reset Unauthorized Access 0 to 1 --- 1 F126 0 (No)
Fault Location (Read Only) (5 modules)
2340 Fault 1 Prefault Phase A Current Magnitude 0 to 999999.999 A 0.001 F060 0
2342 Fault 1 Prefault Phase A Current Angle -359.9 to 0 degrees 0.1 F002 0
2343 Fault 1 Prefault Phase B Current Magnitude 0 to 999999.999 A 0.001 F060 0
2345 Fault 1 Prefault Phase B Current Angle -359.9 to 0 degrees 0.1 F002 0
2346 Fault 1 Prefault Phase C Current Magnitude 0 to 999999.999 A 0.001 F060 0


2348 Fault 1 Prefault Phase C Current Angle -359.9 to 0 degrees 0.1 F002 0
2349 Fault 1 Prefault Phase A Voltage Magnitude 0 to 999999.999 V 0.001 F060 0
234B Fault 1 Prefault Phase A Voltage Angle -359.9 to 0 degrees 0.1 F002 0
234C Fault 1 Prefault Phase B Voltage Magnitude 0 to 999999.999 V 0.001 F060 0
234E Fault 1 Prefault Phase B Voltage Angle -359.9 to 0 degrees 0.1 F002 0
234F Fault 1 Prefault Phase C Voltage Magnitude 0 to 999999.999 V 0.001 F060 0
2351 Fault 1 Prefault Phase C Voltage Angle -359.9 to 0 degrees 0.1 F002 0
2352 Fault 1 Phase A Current Magnitude 0 to 999999.999 A 0.001 F060 0
2354 Fault 1 Phase A Current Angle -359.9 to 0 degrees 0.1 F002 0
2355 Fault 1 Phase B Current Magnitude 0 to 999999.999 A 0.001 F060 0
B
2357 Fault 1 Phase B Current Angle -359.9 to 0 degrees 0.1 F002 0
2358 Fault 1 Phase C Current Magnitude 0 to 999999.999 A 0.001 F060 0
235A Fault 1 Phase C Current Angle -359.9 to 0 degrees 0.1 F002 0
235B Fault 1 Phase A Voltage Magnitude 0 to 999999.999 V 0.001 F060 0
235D Fault 1 Phase A Voltage Angle -359.9 to 0 degrees 0.1 F002 0
235E Fault 1 Phase B Voltage Magnitude 0 to 999999.999 V 0.001 F060 0
2360 Fault 1 Phase B Voltage Angle -359.9 to 0 degrees 0.1 F002 0
2361 Fault 1 Phase C Voltage Magnitude 0 to 999999.999 V 0.001 F060 0
2363 Fault 1 Phase C Voltage Angle -359.9 to 0 degrees 0.1 F002 0
2364 Fault 1 Type 0 to 11 --- 1 F148 0 (NA)
2365 Fault 1 Location based on Line length units (km or miles) -3276.7 to 3276.7 --- 0.1 F002 0
2366 ...Repeated for Fault 2
238C ...Repeated for Fault 3
23B2 ...Repeated for Fault 4
23D8 ...Repeated for Fault 5
Synchrocheck Actuals (Read Only) (4 modules)
2400 Synchrocheck 1 Delta Voltage -1000000000000 to V 1 F060 0
1000000000000
2402 Synchrocheck 1 Delta Frequency 0 to 655.35 Hz 0.01 F001 0
2403 Synchrocheck 1 Delta Phase 0 to 359.9 degrees 0.1 F001 0
2404 ...Repeated for Synchrocheck 2
2408 ...Repeated for Synchrocheck 3
240C ...Repeated for Synchrocheck 4
Autoreclose Status (Read Only) (6 modules)
2410 Autoreclose 1 Count 0 to 65535 --- 1 F001 0
Field Unit Raw Data Settings (Read/Write Setting)
2460 Field Raw Data Port 0 to 7 --- 1 F244 6 (H1a)
2461 Field Raw Data Freeze 0 to 1 --- 1 F102 0 (Disabled)
Phasor Measurement Unit actual values (Read Only) (4 modules)
2540 PMU 1 Phase A Voltage Magnitude 0 to 999999.999 V 0.001 F060 0
2542 PMU Unit 1 Phase A Voltage Angle -359.9 to 0 ° 0.1 F002 0
2543 PMU 1 Phase B Voltage Magnitude 0 to 999999.999 V 0.001 F060 0
2545 PMU 1 Phase B Voltage Angle -359.9 to 0 ° 0.1 F002 0
2546 PMU 1 Phase C Voltage Magnitude 0 to 999999.999 V 0.001 F060 0
2548 PMU 1 Phase C Voltage Angle -359.9 to 0 ° 0.1 F002 0
2549 PMU 1 Auxiliary Voltage Magnitude 0 to 999999.999 V 0.001 F060 0
254B PMU 1 Auxiliary Voltage Angle -359.9 to 0 ° 0.1 F002 0
254C PMU 1 Positive Sequence Voltage Magnitude 0 to 999999.999 V 0.001 F060 0
254E PMU 1 Positive Sequence Voltage Angle -359.9 to 0 ° 0.1 F002 0


254F PMU 1 Negative Sequence Voltage Magnitude 0 to 999999.999 V 0.001 F060 0
2551 PMU 1 Negative Sequence Voltage Angle -359.9 to 0 ° 0.1 F002 0
2552 PMU 1 Zero Sequence Voltage Magnitude 0 to 999999.999 V 0.001 F060 0
2554 PMU 1 Zero Sequence Voltage Angle -359.9 to 0 ° 0.1 F002 0
2555 PMU 1 Phase A Current Magnitude 0 to 999999.999 A 0.001 F060 0
2557 PMU 1 Phase A Current Angle -359.9 to 0 ° 0.1 F002 0
2558 PMU 1 Phase B Current Magnitude 0 to 999999.999 A 0.001 F060 0
255A PMU 1 Phase B Current Angle -359.9 to 0 ° 0.1 F002 0
255B PMU 1 Phase C Current Magnitude 0 to 999999.999 A 0.001 F060 0
255D PMU 1 Phase C Current Angle -359.9 to 0 ° 0.1 F002 0
255E PMU 1 Ground Current Magnitude 0 to 999999.999 A 0.001 F060 0
2560 PMU 1 Ground Current Angle -359.9 to 0 ° 0.1 F002 0 B
2561 PMU 1 Positive Sequence Current Magnitude 0 to 999999.999 A 0.001 F060 0
2563 PMU 1 Positive Sequence Current Angle -359.9 to 0 ° 0.1 F002 0
2564 PMU 1 Negative Sequence Current Magnitude 0 to 999999.999 A 0.001 F060 0
2566 PMU 1 Negative Sequence Current Angle -359.9 to 0 ° 0.1 F002 0
2567 PMU 1 Zero Sequence Current Magnitude 0 to 999999.999 A 0.001 F060 0
2569 PMU 1 Zero Sequence Current Angle -359.9 to 0 ° 0.1 F002 0
256A PMU 1 Frequency 2 to 90 Hz 0.001 F003 0
256C PMU 1 df/dt -327.67 to 327.67 Hz/s 0.01 F002 0
256D PMU 1 Configuration Change Counter 0 to 655.35 0.01 F001 0
256E Reserved (4 items) 0 to 1 --- 1 F001 0
Phasor measurement unit integer values (read only actual value registers) (4 modules)
2608 PMU 1 SOC timestamp 0 to 4294967295 seconds 1 F003 0
260A PMU 1 FRAMESEC timestamp 0 to 4294967295 seconds 1 F003 0
260C PMU 1 STAT flags 0 to 4294967295 --- 1 F003 0
Remote double-point status inputs (read/write setting registers) (5 modules)
2620 Remote double-point status input 1 device 1 to 32 --- 1 F001 1
2621 Remote double-point status input 1 item 0 to 128 --- 1 F156 0 (None)
2622 Remote double-point status input 1 name 1 to 64 --- 1 F205 "Rem Ip 1"
2628 Remote double-point status input 1 events 0 to 1 --- 1 F102 0 (Disabled)
2629 ... Repeated for double-point status input 2
263B ... Repeated for double-point status input 4
Phasor measurement unit actuals (read only) (4 modules)
2650 PMU 1 Aggregator PDU Size --- --- --- F001 0
IEC 61850 GGIO5 configuration (read/write setting registers) (16 modules)
26B0 IEC 61850 GGIO5 uinteger input 1 operand --- --- --- F612 0
26BA IEC 61850 GGIO5 uinteger input 11 operand --- --- --- F612 0
26BB IEC 61850 GGIO5 uinteger input 12 operand --- --- --- F612 0
26BC IEC 61850 GGIO5 uinteger input 13 operand --- --- --- F612 0
26BD IEC 61850 GGIO5 uinteger input 14 operand --- --- --- F612 0
26BE IEC 61850 GGIO5 uinteger input 15 operand --- --- --- F612 0
26BF IEC 61850 GGIO5 uinteger input 16 operand --- --- --- F612 0


IEC 61850 received integers (read only actual values)
26F0 IEC 61850 received uinteger 1 0 to 4294967295 --- 1 F003 0
26FA IEC 61850 received uinteger 6 0 to 4294967295 --- 1 F003 0
26FC IEC 61850 received uinteger 7 0 to 4294967295 --- 1 F003 0
26FE IEC 61850 received uinteger 8 0 to 4294967295 --- 1 F003 0
2700 IEC 61850 received uinteger 9 0 to 4294967295 --- 1 F003 0
B
270A IEC 61850 received uinteger 14 0 to 4294967295 --- 1 F003 0
270C IEC 61850 received uinteger 15 0 to 4294967295 --- 1 F003 0
270E IEC 61850 received uinteger 16 0 to 4294967295 --- 1 F003 0
Expanded FlexStates (Read Only)
2B00 FlexStates, one per register (256 items) 0 to 1 --- 1 F108 0 (Off)
Expanded Digital Input/Output states (Read Only)
2D00 Contact Input States, one per register (96 items) 0 to 1 --- 1 F108 0 (Off)
2D80 Contact Output States, one per register (64 items) 0 to 1 --- 1 F108 0 (Off)
2E00 Virtual Output States, one per register (96 items) 0 to 1 --- 1 F108 0 (Off)
Expanded Remote Input/Output Status (Read Only)
2F00 Remote Device States, one per register (16 items) 0 to 1 --- 1 F155 0 (Offline)
2F80 Remote Input States, one per register (64 items) 0 to 1 --- 1 F108 0 (Off)
Oscillography Values (Read Only)
3000 Oscillography Number of Triggers 0 to 65535 --- 1 F001 0
3001 Oscillography Available Records 0 to 65535 --- 1 F001 0
3002 Oscillography Last Cleared Date 0 to 400000000 --- 1 F050 0
3004 Oscillography Number Of Cycles Per Record 0 to 65535 --- 1 F001 0
Oscillography Commands (Read/Write Command)
3005 Oscillography Force Trigger 0 to 1 --- 1 F126 0 (No)
3011 Oscillography Clear Data 0 to 1 --- 1 F126 0 (No)
3012 Oscillography Number of Triggers 0 to 32767 --- 1 F001 0
Fault Report Indexing (Read Only Non-Volatile)
3020 Number of Fault Reports 0 to 65535 --- 1 F001 0
Fault Report Actuals (Read Only Non-Volatile) (15 modules)
3030 Fault Report 1 Time 0 to 4294967295 --- 1 F050 0
303A Fault Report 6 Time 0 to 4294967295 --- 1 F050 0
303C Fault Report 7 Time 0 to 4294967295 --- 1 F050 0
303E Fault Report 8 Time 0 to 4294967295 --- 1 F050 0
304A Fault Report 14 Time 0 to 4294967295 --- 1 F050 0
304C Fault Report 15 Time 0 to 4294967295 --- 1 F050 0


Modbus file transfer (read/write)
3100 Name of file to read --- --- --- F204 (none)
Modbus file transfer values (read only)
3200 Character position of current block within file 0 to 4294967295 --- 1 F003 0
3202 Size of currently-available data block 0 to 65535 --- 1 F001 0
3203 Block of data from requested file (122 items) 0 to 65535 --- 1 F001 0
Security (Read Only)
328A Administrator alphanumeric password status 0 to 1 --- 1 F102 0 (Disabled)
329F Supervisor alphanumeric password status 0 to 1 --- 1 F102 0 (Disabled)
32B4 Engineer alphanumeric password status 0 to 1 --- 1 F102 0 (Disabled) B
32C9 Operator alphanumeric password status 0 to 1 --- 1 F102 0 (Disabled)
32DE Observer alphanumeric password status 0 to 1 --- 1 F102 0 (Disabled)
32E9 Reserved for password settings of future roles (63 items) 0 to 65535 --- 1 F001 0
3328 Security status indicator 0 to 65535 --- 1 F618 0
Security (Read/Write Setting)
3329 Session Lockout 0 to 99 --- 1 F001 3
332A Session Lockout Period 0 to 9999 min 1 F001 3
332B Load Factory Defaults 0 to 1 --- 1 F126 0 (No)
332C Syslog Serve IP Address 0 to 4294967295 --- 1 F003 0
332E Syslog Server Port Number 0 to 65535 --- 1 F001 514
Security Supervisory (Read/Write Setting)
3331 Device Authentication Enable 0 to 1 --- 1 F126 1 (Yes)
3332 Supervisor Role Enable 0 to 1 --- 1 F102 0 (Disabled)
3333 Lock Relay 0 to 1 --- 1 F102 0 (Disabled)
3334 Factory Service Mode Enable 0 to 1 --- 1 F102 0 (Disabled)
3335 Failed Authentication Alarm Enable 0 to 1 --- 1 F102 1 (Enabled)
3336 Firmware Lock Alarm 0 to 1 --- 1 F102 1 (Enabled)
3337 Settings Lock Alarm 0 to 1 --- 1 F102 1 (Enabled)
3338 Bypass Access 0 to 1 --- 1 F628 0 (Disabled)
3339 Encryption 0 to 1 --- 1 F102 1 (Enabled)
333A Serial Inactivity Timeout 1 to 9999 --- 1 F001 1
Security Command (Read/Write Command)
3350 Operator Logoff 0 to 1 --- 1 F126 0 (No)
3351 Engineer Logoff 0 to 1 --- 1 F126 0 (No)
3352 Administrator Logoff 0 to 1 --- 1 F126 0 (No)
3353 Clear Security Data 0 to 1 --- 1 F126 0 (No)
Security Reserved Modbus Registers (Read/Write)
3360 Address 0x3360 reserved for serial login (20 items) 0 to 9999 --- 1 F001 3
3374 Address 0x3374 reserved for serial logout 0 to 9999 --- 1 F001 3
Security Reserved Modbus Registers (Read Only)
3375 Address 0x3374 reserved for serial logout 0 to 5 --- 1 F617 3 (Engineer)
Event recorder actual values (read only)
3400 Events Since Last Clear 0 to 4294967295 --- 1 F003 0
3402 Number of Available Events 0 to 4294967295 --- 1 F003 0
3404 Event Recorder Last Cleared Date 0 to 4294967295 --- 1 F050 0
Event recorder commands (read/write)
3406 Event Recorder Clear Command 0 to 1 --- 1 F126 0 (No)
DCMA Input Values (Read Only) (24 modules)
34C0 DCMA Inputs 1 Value -9999999 to 9999999 --- 1 F004 0


34CA DCMA Inputs 6 Value -9999999 to 9999999 --- 1 F004 0
34CC DCMA Inputs 7 Value -9999999 to 9999999 --- 1 F004 0
34CE DCMA Inputs 8 Value -9999999 to 9999999 --- 1 F004 0
34D0 DCMA Inputs 9 Value -9999999 to 9999999 --- 1 F004 0
B
34DA DCMA Inputs 14 Value -9999999 to 9999999 --- 1 F004 0
34DC DCMA Inputs 15 Value -9999999 to 9999999 --- 1 F004 0
34DE DCMA Inputs 16 Value -9999999 to 9999999 --- 1 F004 0
34E0 DCMA Inputs 17 Value -9999999 to 9999999 --- 1 F004 0
34EA DCMA Inputs 22 Value -9999999 to 9999999 --- 1 F004 0
34EC DCMA Inputs 23 Value -9999999 to 9999999 --- 1 F004 0
34EE DCMA Inputs 24 Value -9999999 to 9999999 --- 1 F004 0
RTD Input Values (Read Only) (48 modules)
34F0 RTD Input 1 Value -32768 to 32767 °C 1 F002 0
34FA RTD Input 11 Value -32768 to 32767 °C 1 F002 0
34FB RTD Input 12 Value -32768 to 32767 °C 1 F002 0
34FC RTD Input 13 Value -32768 to 32767 °C 1 F002 0
34FD RTD Input 14 Value -32768 to 32767 °C 1 F002 0
34FE RTD Input 15 Value -32768 to 32767 °C 1 F002 0
34FF RTD Input 16 Value -32768 to 32767 °C 1 F002 0
3500 RTD Input 17 Value -32768 to 32767 °C 1 F002 0
350A RTD Input 27 Value -32768 to 32767 °C 1 F002 0
350B RTD Input 28 Value -32768 to 32767 °C 1 F002 0
350C RTD Input 29 Value -32768 to 32767 °C 1 F002 0
350D RTD Input 30 Value -32768 to 32767 °C 1 F002 0


350E RTD Input 31 Value -32768 to 32767 °C 1 F002 0
350F RTD Input 32 Value -32768 to 32767 °C 1 F002 0
3519 RTD Input 42 Value -32768 to 32767 °C 1 F002 0 B
351A RTD Input 43 Value -32768 to 32767 °C 1 F002 0
351B RTD Input 44 Value -32768 to 32767 °C 1 F002 0
351C RTD Input 45 Value -32768 to 32767 °C 1 F002 0
351D RTD Input 46 Value -32768 to 32767 °C 1 F002 0
351E RTD Input 47 Value -32768 to 32767 °C 1 F002 0
351F RTD Input 48 Value -32768 to 32767 °C 1 F002 0
Ohm Input Values (Read Only) (2 modules)
3520 Ohm Inputs 1 Value 0 to 65535 Þ 1 F001 0
3521 Ohm Inputs 2 Value 0 to 65535 Þ 1 F001 0
Expanded Direct Input/Output Status (Read Only)
3560 Direct Device States, one per register (8 items) 0 to 1 --- 1 F155 0 (Offline)
3570 Direct Input States, one per register (96 items) 0 to 1 --- 1 F108 0 (Off)
Radius Configuration (Read/Write Setting)
3735 Undefined 0 to 4294967295 --- 1 F003 56554706
3737 Undefined 1 to 65535 --- 1 F001 1812
3738 Undefined 1 to 65535 --- 1 F001 1813
3739 Undefined 0 to 4294967295 --- 1 F003 56554706
373B Undefined 0 to 65535 --- 1 F001 1812
373D Undefined 0 to 65535 --- 1 F001 1813
373F Undefined --- --- 1 F619 0 (EAP-TTLS)
3740 Undefined 1 to 65535 --- 1 F001 2910
3741 Undefined 0 to 9999 sec 1 F001 10
3742 Undefined 0 to 9999 --- 1 F001 3
3743 Undefined --- --- --- F002 (none)
PTP Basic Configuration (Read/Write Setting)
3750 PTP Strict Power Profile 0 to 1 --- 1 F102 1 (Enabled)
3751 PTP Domain Number 0 to 255 --- 1 F001 0
3752 PTP VLAN Priority 0 to 7 --- 1 F001 4
3753 PTP VLAN ID 0 to 4095 --- 1 F001 0
3754 Undefined (2 items) 0 to 1 --- 1 F001 0
PTP Port Configuration (Read/Write Setting) (3 modules)
3756 PTP Port x Function 0 to 1 --- 1 F102 0 (Disabled)
3757 Port x Path Delay Adder 0 to 60000 ns 1 F001 0
3758 Port x Path Delay Asymmetry -1000 to 1000 ns 1 F002 0
375C ...Repeated for module number 3
Real Time Clock Synchronizing Actuals (Read Only)
375F RTC Sync Source 0 to 5 --- 1 F624 0 (none)
3760 PTP GrandMaster ID 0 to 100 -- 1 F073 0
3764 Real Time Clock Accuracy 0 to 999999999 ns 1 F003 0
3766 PTP Port 1 State (3 items) 0 to 4 -- 1 F625 0 (Disabled)
3769 RTC Offset 0 to 999999999 ns 1 F004 0


376B PTP - IRIG-B Delta -500000000 to 500000000 ns 1 F004 0
Real Time Clock Synchronizing FlexAnalogs (Read Only)
376D PTP - IRIG-B Delta FlexAnalog -262143 to 262143 --- 1 F004 0
Field Units (Read/Write Setting) (8 modules)
3800 Field Unit 1 ID 0 to 1 --- 1 F205 "U1"
3806 Field Unit 1 Function 0 to 1 --- 1 F102 0 (Disabled)
3807 Field Unit 1 Type 0 to 3 --- 1 F243 0 (CC-05)
3808 Field Unit 1 Serial Number 0 to1 --- 1 F205 "000000000000"
380E Field Unit 1 Port 1 to 4 --- 1 F001 1
380F ...Repeated for Field Unit 2
B
381E ...Repeated for Filed Unit 3
382D ...Repeated for Filed Unit 4
383C ...Repeated for Filed Unit 5
384B ...Repeated for Filed Unit 6
385A ...Repeated for Filed Unit 7
3869 ...Repeated for Filed Unit 8
Field Unit Process Card Ports (Read/Write Setting)
3878 Field Unit 1 Process Card Port 0 to 7 --- 1 F244 6 (H1a)
3879 Field Unit 2 Process Card Port 0 to 7 --- 1 F244 4 (H2a)
387A Field Unit3 Process Card Port 0 to 7 --- 1 F244 2 (H3a)
387B Field Unit 4 Process Card Port 0 to 7 --- 1 F244 0 (H4a)
387C Field Unit 5 Process Card Port 0 to 7 --- 1 F244 7 (H1b)
387D Field Unit 6 Process Card Port 0 to 7 --- 1 F244 5 (H2b)
387E Field Unit 7 Process Card Port 0 to 7 --- 1 F244 3 (H3b)
387F Field Unit 8 Process Card Port 0 to 7 --- 1 F244 1 (H4b)
Field Unit CT VT Settings (Read/Write Setting) (6 modules)
3890 Remote Phase CT x Origin 1 0 to 16 --- 1 F247 0 (none)
3891 Remote Phase CT x Origin 2 0 to 16 --- 1 F247 0 (none)
3892 Remote Ground CT x Origin 1 0 to 16 --- 1 F248 0 (none))
3893 Remote Ground CT x Origin 2 0 to 16 --- 1 F248 0 (none)
3894 AC Bank Redundancy Type 0 to 2 --- 1 F261 1 (Dependability
Biased)
3895 Remote Phase CT 1 Primary 1 to 65000 --- 1 F001 1
3896 Remote Phase CT 1 Secondary 0 to 1 --- 1 F123 0 (1 A)
3897 Remote Ground CT 1 Primary 1 to 65000 --- 1 F001 1
3898 Remote Ground CT 1 Secondary 0 to 1 --- 1 F123 0 (1 A)
3899 Remote Phase VT 1 Connection 0 to 1 --- 1 F100 0 (Wye)
389A Remote Phase VT 1 Secondary 25 to 240 --- 0.1 F001 664
389B Remote Phase VT 1 Ratio 1 to 24000 --- 1 F060 1
389D Remote Auxiliary VT 1 Connection 0 to 6 --- 1 F166 1 (Vag)
389E Remote Auxiliary VT 1 Secondary 25 to 240 --- 0.1 F001 664
389F Remote Auxiliary VT 1 Ratio 1 to 24000 --- 1 F060 1
38A1 ...Repeated for module number 2
38B2 ...Repeated for module number 3
38E5 ...Repeated for module number 6
Field Unit Contact Inputs (Read/Write Setting) (40 modules)
3900 Field Contact Input 1 ID --- --- 1 F205 "FCI 1"
3906 Field Contact Input 1 Origin 0 to 8 --- 1 F256 0 (none)
3907 Field Contact Input 1 Input 1 to 18 --- 1 F001 1
3908 Field Contact Input 1 Failsafe Value 0 to 1 --- 1 F108 0 (Off)
3909 Field Contact Input 1 Debounce Time 0 to 16 ms 0.5 F001 20
390A Field Contact Input 1 Events 0 to 1 --- 1 F102 1 (Enabled)


390B ...Repeated for Field Contact Input 2
3916 ...Repeated for Field Contact Input 3
392C ...Repeated for Field Contact Input 5
394D ...Repeated for Field Contact Input 8
3958 ...Repeated for Field Contact Input9
396E ...Repeated for Field Contact Input 11
3984 ...Repeated for Field Contact Input 13 B
398F ...Repeated for Field Contact Input 14
399A ...Repeated for Field Contact Input 15
39A5 ...Repeated for Field Contact Input 16
39B0 ...Repeated for Field Contact Input 17
39BB ...Repeated for Field Contact Input 18
39C6 ...Repeated for Field Contact Input 19
39D1 ...Repeated for Field Contact Input 20
39DC ...Repeated for Field Contact Input 21
39E7 ...Repeated for Field Contact Input 22
39F2 ...Repeated for Field Contact Input 23
39FD ...Repeated for Field Contact Input 24
3A1E ...Repeated for Field Contact Input 27
3A3F ...Repeated for Field Contact Input 30
3A4A ...Repeated for Field Contact Input 31
3A6B ...Repeated for Field Contact Input 34
3A8C ...Repeated for Field Contact Input 37
3AA2 ...Repeated for Field Contact Input 39
3AAD ...Repeated for Field Contact Input 40
Field Unit Shared Inputs (Read/Write Setting) (16 modules)
3B00 Field Shared Input 1 ID 0 to 65535 --- 1 F205 "SI 1"
3B06 Field Shared Input 1 Unit Origin 1 0 to 8 --- 1 F256 0 (none)
3B07 Field Shared Input 1Channel Origin 1 1 to 15 --- 1 F001 1
3B08 Field Shared Input 1 Events 0 to 1 --- 1 F102 1 (Enabled)
3B09 ...Repeated for Field Shared Input 2
3B1B ...Repeated for Field Shared Input 4
3B2D ...Repeated for Field Shared Input 6
3B3F ...Repeated for Field Shared Input 8
3B5A ...Repeated for Field Shared Input 11


3B6C ...Repeated for Field Shared Input 13
3B7E ...Repeated for Field Shared Input 15
Field Unit Contact Outputs (Read/Write Setting) (8 modules)
3B90 Field Contact Output 1 ID (6 items) --- --- --- F205 "FCO U /OUT"
3BB4 Field Output 1 Operate (6 items) 0 to 4294967295 --- 1 F300 0
3BC0 Field Output 1 Seal In (6 items) 0 to 4294967295 --- 1 F300 0
3BCC Field Output 1 Events (6 items) 0 to 1 --- 1 F102 1 (Enabled)
B
3BD2 ...Repeated for Field Contact Output 2
3C14 ...Repeated for Field Contact Output 3
3CDA ...Repeated for Field Contact Output 6
3D1C ...Repeated for Field Contact Output 7
3D5E ...Repeated for Field Contact Output 8
Field Unit Latching Outputs (Read/Write Setting) (8 modules)
3DC7 Field Latching Output 1 ID 0 to 1 --- --- F205 "FLO Ux /LO"
3DCD Field Latching Output 1 Open 0 to 4294967295 --- 1 F300 0
3DCF Field Latching Output 1 Close 0 to 4294967295 --- 1 F300 0
3DD1 Field Latching Output 1 Events 0 to 1 --- 1 F102 1 (Enabled)
3DD2 Field Latching Output 1 Reserved (2 items) 0 to 1 --- 1 F001 0
3DD4 ...Repeated for Fielding Latching Output 2
3DE1 ...Repeated for Field Contact Output 3
3DEE ...Repeated for Field Contact Output 4
3DFB ...Repeated for Field Contact Output 5
3E08 ...Repeated for Field Contact Output 6
Field Unit Shared Outputs (Read/Write Setting) (16 modules)
3E30 Field Shared Output 1 ID 0 to 65535 --- --- F205 "SO 1"
3E36 Field Shared Output 1 Operate 0 to 4294967295 --- 1 F300 0
3E38 Field Shared Output 1 Unit Dest 1 0 to 8 --- 1 F256 0 (none)
3E39 Field Shared Output 1 Channel Dest 1 0 to 15 --- 1 F001 1
3E3A Field Shared Output 1 Unit Dest 2 0 to 8 --- 1 F256 0 (none)
3E3B Field Shared Output 1 Channel Dest 2 1 to 15 --- 1 F001 1
3E3C Field Shared Output 1 Events 0 to 1 --- 1 F102 1 (Enabled)
3E3D ...Repeated for Field Shared Output 2
3E4A ...Repeated for Field Shared Output 3
3E57 ...Repeated for Field Shared Output 4
3E7E ...Repeated for Field Shared Output 7
3E8B ...Repeated for Field Shared Output 8
3EA5 ...Repeated for Field Shared Output 10
3EB2 ...Repeated for Field Shared Output 11
3EBF ...Repeated for Field Shared Output 12
3ECC ...Repeated for Field Shared Output 13
3ED9 ...Repeated for Field Shared Output 14
3EE6 ...Repeated for Field Shared Output 15
3EF3 ...Repeated for Field Shared Output 16


Field Unit RTDs (Read/Write Setting) (8 modules)
3F00 Field Unit RTD 1Name 0 to 1 --- 1 F205 "RTD 1"
3F06 Field Unit RTD 1 Origin 0 to 1 --- 1 F205 "RTD 1"
3F07 Field Unit RTD 1 Type 0 to 2 --- 1 F259 0 (100 Ohm
Nickel)
3F08 ...Repeated for Field Unit RTD 2
Field Unit Transducers (Read/Write Setting) (8 modules)
B
3F40 Field Unit Transducer 1 Name 0 to 1 --- 1 F205 "TRD 1"
3F46 Field Unit Transducer 1 Origin 0 to 24 --- 1 F53 0 (none)
3F47 Field Unit Transducer 1 Range 0 to 9 --- 1 F246 6 (0...20mA)
3F48 Field Unit Transducer 1 Min Value -9999.999 to 9999.999 --- 0.01 F004 0
3F4A Field Unit Transducer 1 Max Value -9999.999 to 9999.999 --- 0.001 F004 100000
3F4C Field Unit Transducer 1 Units --- --- --- F206 (none)
3F4F ...Repeated for Field Unit Transducer 2
3F5E ...Repeated for Field Unit Transducer 3
3F6D ...Repeated for Field Unit Transducer 4
3F7C ...Repeated for Field Unit Transducer 5
3F8B ...Repeated for Field Unit Transducer 6
3F9A ...Repeated for Field Unit Transducer 7
3FA9 ...Repeated for Field Unit Transducer 8
Field Unit Identifiers (Read Only) (8 modules)
3FB8 Attached Field Unit 1 Serial Number --- --- 1 F205 (none)
3FBE Attached Filed Unit 1 Port Number --- --- 1 F001 0
3FBF Attached Field Unit 1 Type 0 to 3 --- 1 F243 0 (CC-05)
3FC0 Field Unit 1 Status 0 to 4 --- 1 F262 0 (Disabled)
3FC1 ...Repeated for Field Unit 2
3FCA ...Repeated for Field Unit 3
3FD3 ...Repeated for Field Unit 4
3FDC ...Repeated for Field Unit 5
3FE5 ...Repeated for Field Unit 6
3FEE ...Repeated for Field Unit 7
3FF7 ...Repeated for Field Unit 8
Passwords (Read/Write Command)
4000 Command Password Setting 0 to 4294967295 --- 1 F202 0
Passwords (Read/Write Setting)
400A Setting Password Setting 0 to 4294967295 --- 1 F202 0
Passwords (Read/Write)
4014 Command Password Entry 0 to 4294967295 --- 1 F202 (none)
401E Setting Password Entry 0 to 4294967295 --- 1 F202 (none)
Passwords (Read Only)
4028 Command Password Status 0 to 1 --- 1 F102 0 (Disabled)
4029 Setting Password Status 0 to 1 --- 1 F102 0 (Disabled)
402A Command Password Access Timeout 5 to 480 min 1 F001 5
402B Setting Password Access Timeout 5 to 480 min 1 F001 30
402C Invalid Password Attempts 2 to 5 --- 1 F001 3
402D Password Lockout Duration 5 to 60 min 1 F001 5


Passwords (Read/Write)
402E Password Access Events 0 to 1 --- 1 F102 0 (Disabled)
402F Local Setting Auth 1 to 4294967295 --- 1 F300 1
4031 Remote Setting Auth 0 to 4294967295 --- 1 F300 1
4033 Access Auth Timeout 5 to 480 min 1 F001 30
User Display Invoke (Read/Write Setting)
4040 Invoke and Scroll Through User Display Menu Operand 0 to 4294967295 --- 1 F300 0
LED Test (Read/Write Setting)
4048 LED Test Function 0 to 1 --- 1 F102 0 (Disabled)
B
4049 LED Test Control 0 to 4294967295 --- 1 F300 0
Preferences (Read/Write Setting)
404F Language 0 to 3 --- 1 F531 0 (English)
4050 Flash Message Time 0.5 to 10 s 0.1 F001 10
4051 Default Message Timeout 10 to 900 s 1 F001 300
4052 Default Message Intensity 0 to 3 --- 1 F101 0 (25%)
4053 Screen Saver Feature 0 to 1 --- 1 F102 0 (Disabled)
4054 Screen Saver Wait Time 1 to 65535 min 1 F001 30
4055 Current Cutoff Level 0.002 to 0.02 pu 0.001 F001 20
4056 Voltage Cutoff Level 0.1 to 1 V 0.1 F001 10
Communications (Read/Write Setting)
407D COM2 Selection 0 to 3 --- 1 F601 0 (RS485)
407F COM2 Minimum Response Time 0 to 1000 ms 10 F001 0
4080 Modbus Slave Address 1 to 254 --- 1 F001 254
4085 RS485 Com2 Baud Rate 0 to 11 --- 1 F112 8 (115200)
4086 RS485 Com2 Parity 0 to 2 --- 1 F113 0 (None)
4087 IP Address 0 to 4294967295 --- 1 F003 56554706
4089 IP Subnet Mask 0 to 4294967295 --- 1 F003 4294966272
408B Port 1 Gateway IP Address 0 to 4294967295 --- 1 F003 56554497
4097 Port 1 Link Loss Alert 0 to 1 --- 1 F102 0 (Disabled)
409A DNP Channel 1 Port 0 to 5 --- 1 F177 0 (None)
409B DNP Channel 2 Port 0 to 5 --- 1 F177 0 (None)
409C DNP Address 0 to 65519 --- 1 F001 1
409E DNP Client Addresses (2 items) 0 to 4294967295 --- 1 F003 0
40A3 TCP Port Number for the Modbus protocol 0 to 65535 --- 1 F001 502
40A4 TCP/UDP Port Number for the DNP Protocol 0 to 65535 --- 1 F001 20000
40A5 TCP Port Number for the HTTP (Web Server) Protocol 0 to 65535 --- 1 F001 80
40A6 Main UDP Port Number for the TFTP Protocol 0 to 65535 --- 1 F001 69
40A7 Data Transfer UDP Port Numbers for the TFTP Protocol 0 to 65535 --- 1 F001 0
(zero means “automatic”) (2 items)
40A9 DNP Unsolicited Responses Function 0 to 1 --- 1 F102 0 (Disabled)
40AA DNP Unsolicited Responses Timeout 0 to 60 s 1 F001 5
40AB DNP unsolicited responses maximum retries 1 to 255 --- 1 F001 10
40AC DNP unsolicited responses destination address 0 to 65519 --- 1 F001 1
40AD Ethernet operation mode 0 to 1 --- 1 F192 1 (Half-Duplex)
40AE DNP current scale factor 0 to 8 --- 1 F194 2 (1)
40AF DNP voltage scale factor 0 to 8 --- 1 F194 2 (1)
40B0 DNP power scale factor 0 to 8 --- 1 F194 2 (1)
40B1 DNP energy scale factor 0 to 8 --- 1 F194 2 (1)
40B2 DNP power scale factor 0 to 8 --- 1 F194 2 (1)
40B3 DNP other scale factor 0 to 8 --- 1 F194 2 (1)
40B4 DNP current default deadband 0 to 100000000 --- 1 F003 30000


40B6 DNP voltage default deadband 0 to 100000000 --- 1 F003 30000
40B8 DNP power default deadband 0 to 100000000 --- 1 F003 30000
40BA DNP energy default deadband 0 to 100000000 --- 1 F003 30000
40BC DNP power factor default deadband 0 to 100000000 -- 1 F003 30000
40BE DNP other default deadband 0 to 100000000 --- 1 F003 30000
40C0 DNP IIN time synchronization bit period 1 to 10080 min 1 F001 1440
40C1 DNP message fragment size 30 to 2048 --- 1 F001 240
40C2 DNP client address 3 0 to 4294967295 --- 1 F003 0
40C8 DNP number of paired binary output control points 0 to 32 --- 1 F001 0
40C9 DNP TCP connection timeout 10 to 65535 --- 1 F001 120 B
40CA DNP communications reserved (22 items) 0 to 1 --- 1 F001 0
40E0 TCP port number for the IEC 60870-5-104 protocol 0 to 65535 --- 1 F001 2404
40E1 IEC 60870-5-104 protocol function 0 to 1 --- 1 F102 0 (Disabled)
40E2 IEC 60870-5-104 protocol common address of ASDU 0 to 65535 --- 1 F001 0
40E3 IEC 60870-5-104 protocol cyclic data transmit period 1 to 65535 s 1 F001 60
40E4 IEC 60870-5-104 current default threshold 0 to 100000000 --- 1 F003 30000
40E6 IEC 60870-5-104 voltage default threshold 0 to 100000000 --- 1 F003 30000
40E8 IEC 60870-5-104 power default threshold 0 to 100000000 --- 1 F003 30000
40EA IEC 60870-5-104 energy default threshold 0 to 100000000 --- 1 F003 30000
40EC IEC 60870-5-104 power default threshold 0 to1 --- 0.01 F001 100
40EE IEC 60870-5-104 other default threshold 0 to 100000000 --- 1 F003 30000
40F0 IEC 60870-5-104 client address (5 items) 0 to 4294967295 --- 1 F003 0
4104 IEC 60870-5-104 redundancy port 0 to 1 --- 1 F126 0 (No)
4105 Port 2 IP Address 0 to 4294967295 --- 1 F003 56554706
4107 Port 2 IP Subnet Mask 0 to 4294967295 --- 1 F003 4294966272
4109 Port 2 Gateway IP Address 0 to 4294967295 --- 1 F003 56554497
410B PRT2 Ethernet Operation Mode 0 to 1 --- 1 F192 1 (Full-Duplex)
410C PRT2 Redundancy Enabled 0 to 2 --- 1 F627 0 (None)
410D Port 3 IP Address 0 to 4294967295 --- 1 F003 56554706
410F Port 3 IP Subnet Mask 0 to 4294967295 --- 1 F003 4294966272
4111 Port 3 Gateway IP Address 0 to 4294967295 --- 1 F003 56554497
4113 Port 3 Ethernet Operation Mode 0 to 1 --- 1 F192 1 (Full-Duplex)
4114 PRT1 GOOSE Enabled 0 to 1 --- 1 F102 1 (Enabled)
4119 PRT2 PRP Mcst Addr --- --- --- F072 0
411C IEC Communications Reserved (33 items) 0 to 1 --- 1 F001 0
413E High Enet Traffic Function 0 to 1 --- 1 F102 0 (Disabled)
413F High Enet Traffic Events 0 to 1 --- 1 F102 0 (Disabled)
4140 DNP object 1 default variation 1 to 2 --- 1 F001 2
4142 DNP object 20 default variation 0 to 3 --- 1 F523 0 (1)
Communications Actuals (Read Only)
4160 Modbus Available TCP/IP Connections 0 to 4 --- 1 F001 4
4161 DNP Available TCP/IP Connections 0 to 2 --- 1 F001 2
4162 IEC Available TCP/IP Connections 0 to 2 --- 1 F001 2
4163 MMS Available TCP/IP Connections 0 to 5 --- 1 F001 5


4164 PMU Available TCP/IP Connections 0 to 4 --- 1 F001 4
Simple Network Time Protocol (Read/Write Setting)
4168 Simple Network Time Protocol (SNTP) function 0 to 1 --- 1 F102 0 (Disabled)
4169 Simple Network Time Protocol (SNTP) server IP address 0 to 4294967295 --- 1 F003 0
416B Simple Network Time Protocol (SNTP) UDP port number 1 to 65535 --- 1 F001 123
Data Logger Commands (Read/Write Command)
4170 Data Logger Clear 0 to 1 --- 1 F126 0 (No)
Data Logger (Read/Write Setting)
4181 Data Logger Channel Settings (16 items) --- --- --- F600 0
4191 Data Logger Mode 0 to 1 --- 1 F260 0 (continuous)
B
4192 Data Logger Trigger 0 to 4294967295 --- 1 F300 0
4194 Data Logger Rate 15 to 3600000 ms 1 F003 60000
Clock (Read/Write Setting)
419F Synchronizing Source 0 to 3 --- 1 F623 0 (none)
Clock (Read/Write Command)
41A0 Real Time Clock Set Time 0 to 235959 --- 1 F050 0
Clock (Read/Write Setting)
41A2 SR Date Format 0 to 4294967295 --- 1 F051 0
41A4 SR Time Format 0 to 4294967295 --- 1 F052 0
41A6 IRIG-B Signal Type 0 to 2 --- 1 F114 0 (None)
41A7 Clock Events Enable / Disable 0 to 1 --- 1 F102 0 (Disabled)
41A8 Time Zone Offset from UTC –24 to 24 hours 0.5 F002 0
41A9 Daylight Savings Time (DST) Function 0 to 1 --- 1 F102 0 (Disabled)
41AA Daylight Savings Time (DST) Start Month 0 to 11 --- 1 F237 0 (January)
41AB Daylight Savings Time (DST) Start Day 0 to 6 --- 1 F238 0 (Sunday)
41AC Daylight Savings Time (DST) Start Day Instance 0 to 4 --- 1 F239 0 (First)
41AD Daylight Savings Time (DST) Start Hour 0 to 23 --- 1 F001 2
41AE Daylight Savings Time (DST) Stop Month 0 to 11 --- 1 F237 0 (January)
41AF Daylight Savings Time (DST) Stop Day 0 to 6 --- 1 F238 0 (Sunday)
41B0 Daylight Savings Time (DST) Stop Day Instance 0 to 4 --- 1 F239 0 (First)
41B1 Daylight Savings Time (DST) Stop Hour 0 to 23 --- 1 F001 2
Fault Report Commands (Read/Write Command)
41B2 Fault Reports Clear Data Command 0 to 1 --- 1 F126 0 (No)
Oscillography (Read/Write Setting)
41C0 Oscillography Number of Records 3 to 64 --- 1 F001 15
41C1 Oscillography Trigger Mode 0 to 1 --- 1 F118 0 (Auto.
Overwrite)
41C2 Oscillography Trigger Position 0 to 100 % 1 F001 50
41C3 Oscillography Trigger Source 0 to 4294967295 --- 1 F300 0
41C5 Oscillography AC Input Waveforms 0 to 4 --- 1 F183 2 (16 samples/
cycle)
41D0 Oscillography Analog Channel n (16 items) 0 to 65535 --- 1 F600 0
4200 Oscillography Digital Channel n (63 items) 0 to 4294967295 --- 1 F300 0
Trip and Alarm LEDs (Read/Write Setting)
42B0 Trip LED Input FlexLogic Operand 0 to 4294967295 --- 1 F300 0
42B2 Alarm LED Input FlexLogic Operand 0 to 4294967295 --- 1 F300 0
User Programmable LEDs (Read/Write Setting) (48 modules)
42C0 FlexLogic Operand to Activate LED 0 to 4294967295 --- 1 F300 0
42C2 User LED type (latched or self-resetting) 0 to 1 --- 1 F127 1 (Self-Reset)
42C3 ...Repeated for User-Programmable LED 2
42CC ...Repeated for User-Programmable LED 5
42CF ...Repeated for User-Programmable LED 6
42D2 ...Repeated for User-Programmable LED 7


42DB ...Repeated for User-Programmable LED 10
42DE ...Repeated for User-Programmable LED 11
42E1 ...Repeated for User-Programmable LED 12
42EA ...Repeated for User-Programmable LED 15
42ED ...Repeated for User-Programmable LED 16
42F0 ...Repeated for User-Programmable LED 17
42F6 ...Repeated for User-Programmable LED 19 B
42FC ...Repeated for User-Programmable LED 21
42FF ...Repeated for User-Programmable LED 22
4302 ...Repeated for User-Programmable LED 23
430B ...Repeated for User-Programmable LED 26
430E ...Repeated for User-Programmable LED 27
431A ...Repeated for User-Programmable LED 31
431D ...Repeated for User-Programmable LED 32
432C ...Repeated for User-Programmable LED 37
432F ...Repeated for User-Programmable LED 38
433B ...Repeated for User-Programmable LED 42
433E ...Repeated for User-Programmable LED 43
434A ...Repeated for User-Programmable LED 47
434D ...Repeated for User-Programmable LED 48
PRP Status (Read Only)
4363 Total Received Port A 0 to 4294967295 --- 1 F003 0
4365 Total Received Port B 0 to 4294967295 --- 1 F003 0
4367 Total Mismatches Port A 0 to 4294967295 --- 1 F003 0
4369 Total Mismatches Port B 0 to 4294967295 --- 1 F003 0
436B Total Errors 0 to 4294967295 --- 1 F003 0
IPv4 Route Table (Read/Write Setting) (6 Modules)
4370 IPv4 Network Route 1 Destination 0 to 4294967295 --- 1 F003 2130706433
4372 IPv4 Network Route 1 Netmask 0 to 4294967295 --- 1 F003 4294966272
4374 IPv4 Network Route 1 Gateway 0 to 4294967295 --- 1 F003 2130706433
4376 ...Repeated for Route 2
437C ...Repeated for Route 3


438E ...Repeated for Route 6
Installation (Read/Write Setting)
43E0 Relay Programmed State 0 to 1 --- 1 F133 0 (Not
Programmed)
43E1 Relay Name --- --- --- F202 “Relay-1”
User Programmable Self Tests (Read/Write Setting)
4441 User Programmable Detect Ring Break Function 0 to 1 --- 1 F102 1 (Enabled)
4442 User Programmable Direct Device Off Function 0 to 1 --- 1 F102 1 (Enabled)
4443 User Programmable Remote Device Off Function 0 to 1 --- 1 F102 1 (Enabled)
4444 User Programmable First Ethernet Fail Function 0 to 1 --- 1 F102 0 (Disabled)
B 4445
4446
User Programmable Secondary Ethernet Fail Function
User Programmable Battery Fail Function
0 to 1
0 to 1
---
---
1
1
F102
F102
0 (Disabled)
1 (Enabled)
4447 User Programmable SNTP Fail Function 0 to 1 --- 1 F102 1 (Enabled)
4448 User Programmable IRIG-B Fail Function 0 to 1 --- 1 F102 1 (Enabled)
444A Process Bus Failure Operand 0 to 4294967295 --- 1 F300 0
444C PTP Fail Function 0 to 1 --- 1 F102 1 (Enabled)
444D User Programmable Third Ethernet Fail Function 0 to 1 --- 1 F102 0 (Disabled)
444E User Programmable SFP Fail Function 0 to 1 --- 1 F102 0 (Disabled)
CT Settings (Read/Write Setting) (6 modules)
4480 Phase CT 1 Primary 1 to 65000 A 1 F001 1
4481 Phase CT 1 Secondary 0 to 1 --- 1 F123 0 (1 A)
4482 Ground CT 1 Primary 1 to 65000 A 1 F001 1
4483 Ground CT 1 Secondary 0 to 1 --- 1 F123 0 (1 A)
4484 ...Repeated for CT Bank 2
448C ...Repeated for CT Bank 4
VT Settings (Read/Write Setting) (3 modules)
4500 Phase VT 1 Connection 0 to 1 --- 1 F100 0 (Wye)
4501 Phase VT 1 Secondary 25 to 240 V 0.1 F001 664
4502 Phase VT 1 Ratio 1 to 24000 :1 1 F060 1
4504 Auxiliary VT 1 Connection 0 to 6 --- 1 F166 1 (Vag)
4505 Auxiliary VT 1 Secondary 25 to 240 V 0.1 F001 664
4506 Auxiliary VT 1 Ratio 1 to 24000 :1 1 F060 1
4508 ...Repeated for VT Bank 2
Source Settings (Read/Write Setting) (6 modules)
4580 Source 1 Name 0 to 1 --- --- F206 “SRC 1"
4583 Source 1 Phase CT 0 to 63 --- 1 F400 0
4584 Source 1 Ground CT 0 to 63 --- 1 F400 0
4585 Source 1 Phase VT 0 to 63 --- 1 F400 0
4586 Source 1 Auxiliary VT 0 to 63 --- 1 F400 0
458E ...Repeated for Source 3
459C ...Repeated for Source 5
Power System (Read/Write Setting)
4600 Nominal Frequency 25 to 60 Hz 1 F001 60


4601 Phase Rotation 0 to 1 --- 1 F106 0 (ABC)
4602 Frequency And Phase Reference 0 to 5 --- 1 F167 0 (SRC 1)
4603 Frequency Tracking Function 0 to 1 --- 1 F102 1 (Enabled)
Breaker control (read/write settings)
47D0 Breaker 1 function 0 to 1 --- 1 F102 0 (Disabled)
47D1 Breaker 1 name --- --- --- F206 “Bkr 1"
47D4 Breaker 1 mode 0 to 1 --- 1 F157 0 (3-Pole)
47D5 Breaker 1 open 0 to 4294967295 --- 1 F300 0
47D7 Breaker 1 close 0 to 4294967295 --- 1 F300 0
47D9 Breaker 1 phase A / three-pole closed 0 to 4294967295 --- 1 F300 0
47DB Breaker 1 phase B closed 0 to 4294967295 --- 1 F300 0
47DD Breaker 1 phase C closed 0 to 4294967295 --- 1 F300 0 B
47DF Breaker 1 external alarm 0 to 4294967295 --- 1 F300 0
47E1 Breaker 1 alarm delay 0 to 65.535 s 0.001 F003 0
47E3 Breaker 1 pushbutton control 0 to 1 --- 1 F102 0 (Disabled)
47E4 Breaker 1 manual close recall time 0 to 4294967295 s 0.001 F003 0
47E6 Breaker 1 out of service 0 to 4294967295 --- 1 F300 0
47E8 Breaker 1 block open 0 to 4294967295 --- 1 F300 0
47EA Breaker 1 block close 0 to 4294967295 --- 1 F300 0
47EC Breaker 1 phase A / three-pole opened 0 to 4294967295 --- 1 F300 0
47EE Breaker 1 phase B opened 0 to 4294967295 --- 1 F300 0
47F0 Breaker 1 phase C opened 0 to 4294967295 --- 1 F300 0
47F2 Breaker 1 operate time 0 to 65.535 s 0.001 F001 70
47F3 Breaker 1 events 0 to 1 --- 1 F102 0 (Disabled)
47F4 Reserved 0 to 65535 s 1 F001 0
47F5 ...Repeated for breaker 2
481A ...Repeated for breaker 3
483F ...Repeated for breaker 4
Compensated Overvoltage (Read/Write Grouped Setting)
48F0 Compensated OV Function 0 to 1 --- 1 F102 0 (Disabled)
48F1 Compensated OV Sourced 0 to 5 --- 1 F167 0 (SRC 1)
48F2 Compensated OV Zc Mag 0 to 500 ohm 0.01 F001 200
48F3 Compensated OV Zc Ang 30 to 90 degree 1 F001 90
48F4 Compensated OV I_1max 0.01 to 1 pu 0.01 F001 20
48F5 Compensated OV STG1 PKP 0.25 to 3 pu 0.001 F001 1300
48F6 Compensated OV STG1 Delay 0 to 600 sec 0.01 F001 100
48F7 Compensated OV STG2 PKP 0.25 to 3 pu 0.001 F001 1300
48F8 Compensated OV STG2 Delay 0 to 600 sec 0.01 F001 100
48F9 Compensated OV SGT3 PKP 0.25 to 3 pu 0.001 F001 1300
48FA Compensated OV STG3 Delay 0 to 600 sec 0.01 F001 100
48FB Compensated OV Block 0 to 4294967295 --- 1 F300 0
48FD Compensated OV Target 0 to 2 --- 1 F109 0 (Self-reset)
48FE Compensated OV Events 0 to 1 --- 1 F102 0 (Disabled)
FlexCurve A (Read/Write Setting)
4910 FlexCurve A (120 items) 0 to 655535 ms 1 F011 0
FlexCurve B (Read/Write Setting)
4988 FlexCurve B (120 items) 0 to 655535 ms 1 F011 0
Modbus User Map (Read/Write Setting)
4A00 Modbus Address Settings for User Map (256 items) 0 to 65535 --- 1 F001 0
User Displays Settings (Read/Write Setting) (16 modules)
4C00 User-Definable Display 1 Top Line Text --- --- --- F202 ““
4C0A User-Definable Display 1 Bottom Line Text --- --- --- F202 ““
4C14 Modbus Addresses of Display 1 Items (5 items) 0 to 65535 --- 1 F001 0
4C19 Reserved (7 items) --- --- --- F001 0


4C20 ...Repeated for User-Definable Display 2
4CA0 ...Repeated for User-Definable Display 6
4CC0 ...Repeated for User-Definable Display 7
4CE0 ...Repeated for User-Definable Display 8
4D00 ...Repeated for User-Definable Display 9
B
4DA0 ...Repeated for User-Definable Display 14
4DC0 ...Repeated for User-Definable Display 15
4DE0 ...Repeated for User-Definable Display 16
Field Unit Raw Data Actuals (Read Only) (8 modules)
4E00 Raw Field Data AC1 Mag 0 to 0.001 A 0.001 F003 0
4E02 Raw Field Data AC1 Angle 0 to 0.1 degree 0.1 F002 0
4E0B Raw Field Data AC4 Angle 0 to 0.01 degree 0.1 F002 0
4E0C Raw Field Data AC5 Mag 0 to 0.001 A/V 0.001 F003 0
4E0E Raw Field Data AC5 Angle 0 to 0.01 degree 0.1 F002 0
4E0F Raw Field Data AC6 Mag 0 to 0.001 A/V 0.001 F003 0
4E12 Raw Field Data AC7 Mag 0 to 0.001 A/V 0.001 F003 0
4E15 Raw Field Data AC8 Mag 0 to 0.001 A/V 0.001 F003 0
4E18 Raw Field Data DC1 0 to 0.001 V 0.001 F002 0
4E19 Raw Field Data DC2 0 to 0.001 V 0.001 F002 0
4E1A Raw Field Data DC3 0 to 0.001 V 0.001 F002 0
4E1B Raw Field Data FCI States (2 items) 0 to 1 --- 1 F500 0
4E1D Raw Field Data SI States 0 to 1 --- 1 F500 0
4E1E Raw Field Data SI Test States 0 to 1 --- 1 F500 0
4E1F Raw Field Data Brick ADC Temperature 0 to 1 degree 1 F002 0
4E20 Raw Field Data Brick Transceiver Temperature 0 to 1 degree 1 F002 0
4E21 Raw Field Data Brick Transceiver Voltage 0 to 0.01 V 0.01 F001 0
4E22 Raw Field Data Brick Transceiver Current 0 to 1 mA 1 F001 0
4E23 Raw Field Data Brick Tx Power 0 to 0.01 dBm 0.1 F002 0
4E24 Raw Field Data Brick Rx Power 0 to 0.1 dBm 0.1 F002 0
4E25 Raw Field Data Brick Diagnostics (2 items) 0 to 65535 --- 1 F500 0
4E27 Raw Field Data Local Transceiver Temperature 0 to 1 degree 1 F002 0
4E28 Raw Field Data Local Transceiver Voltage 0 to 0.01 V 0.01 F001 0
4E29 Raw Field Data Local Transceiver Current 0 to 1 mA 1 F001 0
4E2A Raw Field Data Local Tx Power 0 to 0.1 dBm 0.1 F002 0
4E2B Raw Field Data Local Rx Power 0 to 0.1 dBm 0.1 F002 0
4E2C Repeated for module number 2
4E58 Repeated for module number 3


4EDC Repeated for module number 6
4F08 Repeated for module number 7
4F34 Repeated for module number 8
Flexlogic (Read/Write Setting)
5000 FlexLogic Entry (512 items) 0 to 4294967295 --- 1 F300 2097152
RTD Inputs (Read/Write Setting) (48 modules)
5400 RTD Input 1 Function 0 to 1 --- 1 F102 0 (Disabled)
5401 RTD Input 1 ID --- --- --- F205 “RTD Ip 1“
5407 RTD Input 1 Type 0 to 3 --- 1 F174 0 (100 ohm
Platinum)
5414 ...Repeated for RTD Input 2
5428
543C
...Repeated for RTD Input 3
...Repeated for RTD Input 4
B
548C ...Repeated for RTD Input 8
54A0 ...Repeated for RTD Input 9
54B4 ...Repeated for RTD Input 10
54C8 ...Repeated for RTD Input 11
54DC ...Repeated for RTD Input 12
54F0 ...Repeated for RTD Input 13
55B8 ...Repeated for RTD Input 23
55CC ...Repeated for RTD Input 24
55E0 ...Repeated for RTD Input 25
56BC ...Repeated for RTD Input 36
56D0 ...Repeated for RTD Input 37
56E4 ...Repeated for RTD Input 38


57AC ...Repeated for RTD Input 48
Flexlogic Timers (Read/Write Setting) (32 modules)
5800 FlexLogic Timer 1 Type 0 to 2 --- 1 F129 0 (millisecond)
5801 FlexLogic Timer 1 Pickup Delay 0 to 60000 --- 1 F001 0
5802 FlexLogic Timer 1 Dropout Delay 0 to 60000 --- 1 F001 0
5803 Reserved (5 items) 0 to 65535 --- 1 F001 0
5808 ...Repeated for FlexLogic Timer 2
B
58A0 ...Repeated for FlexLogic Timer 21
58A8 ...Repeated for FlexLogic Timer 22
58B0 ...Repeated for FlexLogic Timer 23
58B8 ...Repeated for FlexLogic Timer 24
58C0 ...Repeated for FlexLogic Timer 25
58C8 ...Repeated for FlexLogic Timer 26
58D0 ...Repeated for FlexLogic Timer 27
58D8 ...Repeated for FlexLogic Timer 28
58E0 ...Repeated for FlexLogic Timer 29
58E8 ...Repeated for FlexLogic Timer 30
58F0 ...Repeated for FlexLogic Timer 31
58F8 ...Repeated for FlexLogic Timer 32
Phase Time Overcurrent (Read/Write Grouped Setting) (6 modules)
5900 Phase Time Overcurrent 1 Function 0 to 1 --- 1 F102 0 (Disabled)
5901 Phase Time Overcurrent 1 Signal Source 0 to 5 --- 1 F167 0 (SRC 1)
5902 Phase Time Overcurrent 1 Input 0 to 1 --- 1 F122 0 (Phasor)
5903 Phase Time Overcurrent 1 Pickup 0 to 30 pu 0.001 F001 1000
5904 Phase Time Overcurrent 1 Curve 0 to 16 --- 1 F103 0 (IEEE Mod Inv)
5905 Phase Time Overcurrent 1 Multiplier 0 to 600 --- 0.01 F001 100
5906 Phase Time Overcurrent 1 Reset 0 to 1 --- 1 F104 0 (Instantaneous)
5907 Phase Time Overcurrent 1 Voltage Restraint 0 to 1 --- 1 F102 0 (Disabled)
5908 Phase TOC 1 Block For Each Phase (3 items) 0 to 4294967295 --- 1 F300 0
590F Phase Time Overcurrent 1 Target 0 to 2 --- 1 F109 0 (Self-reset)
5910 Phase Time Overcurrent 1 Events 0 to 1 --- 1 F102 0 (Disabled)
5914 ...Repeated for Phase Time Overcurrent 2


593C ...Repeated for Phase Time Overcurrent 4
Phase Instantaneous Overcurrent (Read/Write Grouped Setting) (12 modules)
5A00 Phase Instantaneous Overcurrent 1 Function 0 to 1 --- 1 F102 0 (Disabled)
5A01 Phase Instantaneous Overcurrent 1 Signal Source 0 to 5 --- 1 F167 0 (SRC 1)
5A02 Phase Instantaneous Overcurrent 1 Pickup 0 to 30 pu 0.001 F001 1000
5A03 Phase Instantaneous Overcurrent 1 Delay 0 to 600 s 0.01 F001 0
5A04 Phase Instantaneous Overcurrent 1 Reset Delay 0 to 600 s 0.01 F001 0
5A05 Phase IOC1 Block For Each Phase (3 items) 0 to 4294967295 --- 1 F300 0
5A0B Phase Instantaneous Overcurrent 1 Target 0 to 2 --- 1 F109 0 (Self-reset)
5A0C Phase Instantaneous Overcurrent 1 Events 0 to 1 --- 1 F102 0 (Disabled) B
5A0D Reserved (6 items) 0 to 1 --- 1 F001 0
5A13 ...Repeated for Phase Instantaneous Overcurrent 2
5A4C ...Repeated for Phase Instantaneous Overcurrent 5
5A5F ...Repeated for Phase Instantaneous Overcurrent 6
5AAB ...Repeated for Phase Instantaneous Overcurrent 10
5ABE ...Repeated for Phase Instantaneous Overcurrent 11
5AD1 ...Repeated for Phase Instantaneous Overcurrent 12
Neutral Time Overcurrent (Read/Write Grouped Setting) (6 modules)
5B00 Neutral Time Overcurrent 1 Function 0 to 1 --- 1 F102 0 (Disabled)
5B01 Neutral Time Overcurrent 1 Signal Source 0 to 5 --- 1 F167 0 (SRC 1)
5B02 Neutral Time Overcurrent 1 Input 0 to 1 --- 1 F122 0 (Phasor)
5B03 Neutral Time Overcurrent 1 Pickup 0 to 30 pu 0.001 F001 1000
5B04 Neutral Time Overcurrent 1 Curve 0 to 16 --- 1 F103 0 (IEEE Mod Inv)
5B05 Neutral Time Overcurrent 1 Multiplier 0 to 600 --- 0.01 F001 100
5B06 Neutral Time Overcurrent 1 Reset 0 to 1 --- 1 F104 0 (Instantaneous)
5B07 Neutral Time Overcurrent 1 Block 0 to 4294967295 --- 1 F300 0
5B09 Neutral Time Overcurrent 1 Target 0 to 2 --- 1 F109 0 (Self-reset)
5B0A Neutral Time Overcurrent 1 Events 0 to 1 --- 1 F102 0 (Disabled)
5B0B Reserved (6 items) 0 to 1 --- 1 F001 0
5B11 ...Repeated for Neutral Time Overcurrent 2
Neutral Instantaneous Overcurrent (Read/Write Grouped Setting) (12 modules)
5C00 Neutral Instantaneous Overcurrent 1 Function 0 to 1 --- 1 F102 0 (Disabled)
5C01 Neutral Instantaneous Overcurrent 1 Signal Source 0 to 5 --- 1 F167 0 (SRC 1)
5C02 Neutral Instantaneous Overcurrent 1 Pickup 0 to 30 pu 0.001 F001 1000
5C03 Neutral Instantaneous Overcurrent 1 Delay 0 to 600 s 0.01 F001 0
5C04 Neutral Instantaneous Overcurrent 1 Reset Delay 0 to 600 s 0.01 F001 0
5C05 Neutral Instantaneous Overcurrent 1 Block 0 to 4294967295 --- 1 F300 0
5C07 Neutral Instantaneous Overcurrent 1 Target 0 to 2 --- 1 F109 0 (Self-reset)
5C08 Neutral Instantaneous Overcurrent 1 Events 0 to 1 --- 1 F102 0 (Disabled)
5C09 Reserved (8 items) 0 to 1 --- 1 F001 0
5C11 ...Repeated for Neutral Instantaneous Overcurrent 2


5CAA ...Repeated for Neutral Instantaneous Overcurrent 11
5CBB ...Repeated for Neutral Instantaneous Overcurrent 12
Ground Time Overcurrent (Read/Write Grouped Setting) (6 modules)
5D00 Ground Time Overcurrent 1 Function 0 to 1 --- 1 F102 0 (Disabled)
B
5D01 Ground Time Overcurrent 1 Signal Source 0 to 5 --- 1 F167 0 (SRC 1)
5D02 Ground Time Overcurrent 1 Input 0 to 1 --- 1 F122 0 (Phasor)
5D03 Ground Time Overcurrent 1 Pickup 0 to 30 pu 0.001 F001 1000
5D04 Ground Time Overcurrent 1 Curve 0 to 16 --- 1 F103 0 (IEEE Mod Inv)
5D05 Ground Time Overcurrent 1 Multiplier 0 to 600 --- 0.01 F001 100
5D06 Ground Time Overcurrent 1 Reset 0 to 1 --- 1 F104 0 (Instantaneous)
5D07 Ground Time Overcurrent 1 Block 0 to 4294967295 --- 1 F300 0
5D09 Ground Time Overcurrent 1 Target 0 to 2 --- 1 F109 0 (Self-reset)
5D0A Ground Time Overcurrent 1 Events 0 to 1 --- 1 F102 0 (Disabled)
5D0B Reserved (6 items) 0 to 1 --- 1 F001 0
5D11 ...Repeated for Ground Time Overcurrent 2
Ground Instantaneous Overcurrent (Read/Write Grouped Setting) (12 modules)
5DA0 Ground Instantaneous Overcurrent 1 Function 0 to 1 --- 1 F102 0 (Disabled)
5DA1 Ground Instantaneous Overcurrent 1 Signal Source 0 to 5 --- 1 F167 0 (SRC 1)
5DA2 Ground Instantaneous Overcurrent 1 Pickup 0 to 30 pu 0.001 F001 1000
5DA3 Ground Instantaneous Overcurrent 1 Delay 0 to 600 s 0.01 F001 0
5DA4 Ground Instantaneous Overcurrent 1 Reset Delay 0 to 600 s 0.01 F001 0
5DA5 Ground Instantaneous Overcurrent 1 Block 0 to 4294967295 --- 1 F300 0
5DA7 Ground Instantaneous Overcurrent 1 Target 0 to 2 --- 1 F109 0 (Self-reset)
5DA8 Ground Instantaneous Overcurrent 1 Events 0 to 1 --- 1 F102 0 (Disabled)
5DA9 Reserved (8 items) 0 to 1 --- 1 F001 0
5DB1 ...Repeated for Ground Instantaneous Overcurrent 2
5DC2 ...Repeated for Ground Instantaneous Overcurrent 3
5DD3 ...Repeated for Ground Instantaneous Overcurrent 4
5DE4 ...Repeated for Ground Instantaneous Overcurrent 5
5DF5 ...Repeated for Ground Instantaneous Overcurrent 6
5E06 ...Repeated for Ground Instantaneous Overcurrent 7
5E4A ...Repeated for Ground Instantaneous Overcurrent 11
5E5B ...Repeated for Ground Instantaneous Overcurrent 12
Setting Groups (Read/Write Setting)
5F70 Setting Group for Modbus Comms (0 means group 1) 0 to 5 --- 1 F001 0
5F71 Setting Groups Block 0 to 4294967295 --- 1 F300 0
5F73 FlexLogic to Activate Groups 2 through 6 (5 items) 0 to 4294967295 --- 1 F300 0
5F7D Setting Group Function 0 to 1 --- 1 F102 0 (Disabled)
5F7E Setting Group Events 0 to 1 --- 1 F102 0 (Disabled)
Setting Groups (Read Only)
5F7F Current Setting Group 0 to 5 --- 1 F001 0


Setting Group Names (Read/Write Setting)
5F8C Setting Group 1 Name --- --- --- F203 (none)
5F94 Setting Group 2 Name --- --- --- F203 (none)
5F9C Setting Group 3 Name --- --- --- F203 (none)
5FA4 Setting Group 4 Name --- --- --- F203 (none)
5FAC Setting Group 5 Name --- --- --- F203 (none)
5FB4 Setting Group 6 Name --- --- --- F203 (none)
Negative Sequence Time Overcurrent (Read/Write Grouped Setting) (2 modules)
6300 Negative Sequence Time Overcurrent 1 Function 0 to 1 --- 1 F102 0 (Disabled)
6301 Negative Sequence Time Overcurrent 1 Signal Source 0 to 5 --- 1 F167 0 (SRC 1)
6302 Negative Sequence Time Overcurrent 1 Pickup 0 to 30 pu 0.001 F001 1000
6303 Negative Sequence Time Overcurrent 1 Curve 0 to 16 --- 1 F103 0 (IEEE Mod Inv) B
6304 Negative Sequence Time Overcurrent 1 Multiplier 0 to 600 --- 0.01 F001 100
6305 Negative Sequence Time Overcurrent 1 Reset 0 to 1 --- 1 F104 0 (Instantaneous)
6306 Negative Sequence Time Overcurrent 1 Block 0 to 4294967295 --- 1 F300 0
6308 Negative Sequence Time Overcurrent 1 Target 0 to 2 --- 1 F109 0 (Self-reset)
6309 Negative Sequence Time Overcurrent 1 Events 0 to 1 --- 1 F102 0 (Disabled)
630A Reserved (7 items) 0 to 1 --- 1 F001 0
6311 ...Repeated for Negative Sequence Time Overcurrent 2
Negative Sequence Instantaneous Overcurrent (Read/Write Grouped Setting) (2 modules)
63C0 Negative Sequence Instantaneous OC 1 Function 0 to 1 --- 1 F102 0 (Disabled)
63C1 Negative Sequence Instantaneous OC 1 Signal Source 0 to 5 --- 1 F167 0 (SRC 1)
63C2 Negative Sequence Instantaneous Overcurrent 1 Pickup 0 to 30 pu 0.001 F001 1000
63C3 Negative Sequence Instantaneous Overcurrent 1 Delay 0 to 600 s 0.01 F001 0
63C4 Negative Sequence Instantaneous OC 1 Reset Delay 0 to 600 s 0.01 F001 0
63C5 Negative Sequence Instantaneous Overcurrent 1 Block 0 to 4294967295 --- 1 F300 0
63C7 Negative Sequence Instantaneous Overcurrent 1 Target 0 to 2 --- 1 F109 0 (Self-reset)
63C8 Negative Sequence Instantaneous Overcurrent 1 Events 0 to 1 --- 1 F102 0 (Disabled)
63C9 Reserved (8 items) 0 to 1 --- 1 F001 0
63D1 ...Repeated for Negative Sequence Instantaneous OC 2
Negative Sequence Overvoltage (Read/Write Grouped Setting)
6440 Negative Sequence Overvoltage Function 0 to 1 --- 1 F102 0 (Disabled)
6441 Negative Sequence Overvoltage Source 0 to 5 --- 1 F167 0 (SRC 1)
64A42 Negative Sequence Overvoltage Pickup 0 to 1.25 pu 0.001 F001 300
6443 Negative Sequence Overvoltage Pickup Delay 0 to 600 s 0.01 F001 50
6444 Negative Sequence Overvoltage Reset Delay 0 to 600 s 0.01 F001 50
6445 Negative Sequence Overvoltage Block 0 to 4294967295 --- 1 F300 0
6447 Negative Sequence Overvoltage Target 0 to 2 --- 1 F109 0 (Self-reset)
6448 Negative Sequence Overvoltage Events 0 to 1 --- 1 F102 0 (Disabled)
Overfrequency (Read/Write Setting) (4 modules)
6470 Overfrequency 1 Function 0 to 1 --- 1 F102 0 (Disabled)
6471 Overfrequency 1 Block 0 to 4294967295 --- 1 F300 0
6473 Overfrequency 1 Source 0 to 5 --- 1 F167 0 (SRC 1)
6474 Overfrequency 1 Pickup 20 to 65 Hz 0.01 F001 6050
6475 Overfrequency 1 Pickup Delay 0 to 65.535 s 0.001 F001 500
6476 Overfrequency 1 Reset Delay 0 to 65.535 s 0.001 F001 500
6477 Overfrequency 1 Target 0 to 2 --- 1 F109 0 (Self-reset)
6478 Overfrequency 1 Events 0 to 1 --- 1 F102 0 (Disabled)
647D ...Repeated for Overfrequency 2
648A ...Repeated for Overfrequency 3
6497 ...Repeated for Overfrequency 4


Power Swing Detect (Read/Write Grouped Setting)
65C0 Power Swing Detect Function 0 to 1 --- 1 F102 0 (Disabled)
65C1 Power Swing Detect Source 0 to 5 --- 1 F167 0 (SRC 1)
65C2 Power Swing Detect Mode 0 to 1 --- 1 F513 0 (Two Step)
65C3 Power Swing Detect Supervision 0.05 to 30 pu 0.001 F001 600
65C4 Power Swing Detect Forward Reach 0.1 to 500 ohms 0.01 F001 5000
65C5 Power Swing Detect Forward RCA 40 to 90 degrees 1 F001 75
65C6 Power Swing Detect Reverse Reach 0.1 to 500 ohms 0.01 F001 5000
65C7 Power Swing Detect Reverse RCA 40 to 90 degrees 1 F001 75
65C8 Power Swing Detect Outer Limit Angle 40 to 140 degrees 1 F001 120
B
65C9 Power Swing Detect Middle Limit Angle 40 to 140 degrees 1 F001 90
65CA Power Swing Detect Inner Limit Angle 40 to 140 degrees 1 F001 60
65CB Power Swing Detect Delay 1 Pickup 0 to 65.535 s 0.001 F001 30
65CC Power Swing Detect Delay 1 Reset 0 to 65.535 s 0.001 F001 50
65CD Power Swing Detect Delay 2 Pickup 0 to 65.535 s 0.001 F001 17
65CE Power Swing Detect Delay 3 Pickup 0 to 65.535 s 0.001 F001 9
65CF Power Swing Detect Delay 4 Pickup 0 to 65.535 s 0.001 F001 17
65D0 Power Swing Detect Seal In Delay 0 to 65.535 s 0.001 F001 400
65D1 Power Swing Detect Trip Mode 0 to 1 --- 1 F514 0 (Delayed)
65D2 Power Swing Detect Block 0 to 4294967295 --- 1 F300 0
65D4 Power Swing Detect Target 0 to 2 --- 1 F109 0 (Self-reset)
65D5 Power Swing Detect Event 0 to 1 --- 1 F102 0 (Disabled)
65D6 Power Swing Detect Shape 0 to 1 --- 1 F085 0 (Mho Shape)
65D7 Power Swing Detect Quad Forward Middle 0.1 to 500 ohms 0.01 F001 6000
65D8 Power Swing Detect Quad Forward Outer 0.1 to 500 ohms 0.01 F001 7000
65D9 Power Swing Detect Quad Reverse Middle 0.1 to 500 ohms 0.01 F001 6000
65DA Power Swing Detect Quad Reverse Outer 0.1 to 500 ohms 0.01 F001 7000
65DB Power Swing Detect Outer Right Blinder 0.1 to 500 ohms 0.01 F001 10000
65DC Power Swing Detect Outer Left Blinder 0.1 to 500 ohms 0.01 F001 10000
65DD Power Swing Detect Middle Right Blinder 0.1 to 500 ohms 0.01 F001 10000
65DE Power Swing Detect Middle Left Blinder 0.1 to 500 ohms 0.01 F001 10000
65DF Power Swing Detect Inner Right Blinder 0.1 to 500 ohms 0.01 F001 10000
65E0 Power Swing Detect Inner Left Blinder 0.1 to 500 ohms 0.01 F001 10000
Sensitive Directional Power (Read/Write Grouped Setting) (2 modules)
6680 Sensitive Directional Power 1 Function 0 to 1 --- 1 F102 0 (Disabled)
6681 Sensitive Directional Power 1 Signal Source 0 to 5 --- 1 F167 0 (SRC 1)
6682 Sensitive Directional Power 1 RCA 0 to 359 degrees 1 F001 0
6683 Sensitive Directional Power 1 Calibration 0 to 0.95 degrees 0.05 F001 0
6684 Sensitive Directional Power 1 STG1 SMIN -1.2 to 1.2 pu 0.001 F002 100
6685 Sensitive Directional Power 1 STG1 Delay 0 to 600 s 0.01 F001 50
6686 Sensitive Directional Power 1 STG2 SMIN -1.2 to 1.2 pu 0.001 F002 100
6687 Sensitive Directional Power 1 STG2 Delay 0 to 600 s 0.01 F001 2000
6688 Sensitive Directional Power 1 Block 0 to 4294967295 --- --- F300 0
668A Sensitive Directional Power 1 Target 0 to 2 --- 1 F109 0 (Self-reset)
668B Sensitive Directional Power 1 Events 0 to 1 --- 1 F102 0 (Disabled)
668C Reserved (5 items) 0 to 65535 --- 1 F001 0
6691 ...Repeated for Sensitive Directional Power 2
Load Encroachment (Read/Write Grouped Setting)
66C0 Load Encroachment Function 0 to 1 --- 1 F102 0 (Disabled)
66C1 Load Encroachment Source 0 to 5 --- 1 F167 0 (SRC 1)
66C2 Load Encroachment Minimum Voltage 0 to 3 pu 0.001 F001 250
66C3 Load Encroachment Reach 0.02 to 250 ohms 0.01 F001 100
66C4 Load Encroachment Angle 5 to 50 degrees 1 F001 30
66C5 Load Encroachment Pickup Delay 0 to 65.535 s 0.001 F001 0


66C6 Load Encroachment Reset Delay 0 to 65.535 s 0.001 F001 0
66C7 Load Encroachment Block 0 to 4294967295 --- 1 F300 0
66C9 Load Encroachment Target 0 to 2 --- 1 F109 0 (Self-reset)
66CA Load Encroachment Events 0 to 1 --- 1 F102 0 (Disabled)
66CB Reserved (6 items) 0 to 65535 --- 1 F001 0
Trip Output (Read/Write Setting)
6760 Trip Mode 0 to 2 --- 1 F195 0 (Disabled)
6761 Trip 3-Pole Input1 0 to 4294967295 --- 1 F300 0
6769 Trip 3-Pole Input5 0 to 4294967295 --- 1 F300 0 B
676B Trip 3-Pole Input6 0 to 4294967295 --- 1 F300 0
676D Trip 1-Pole Input1 0 to 4294967295 --- 1 F300 0
676F Trip 1-Pole Input2 0 to 4294967295 --- 1 F300 0
6779 Trip Reclose Input1 0 to 4294967295 --- 1 F300 0
677B Trip Reclose Input2 0 to 4294967295 --- 1 F300 0
677D Trip Reclose Input3 0 to 4294967295 --- 1 F300 0
677F Trip Reclose Input4 0 to 4294967295 --- 1 F300 0
6785 Trip Force 3-Pole 0 to 4294967295 --- 1 F300 0
6787 Trip Pilot Priority 0 to 65.535 s 0.001 F001 0
6788 Breaker Phase A Open 0 to 4294967295 --- 1 F300 0
678A Breaker Phase B Open 0 to 429496729 --- 1 F300 0
678C Breaker Phase C Open 0 to 429496729 --- 1 F300 0
6783 Trip Events 0 to 1 --- 1 F102 0 (Disabled)
678F Reverse Fault Operand 0 to 429496729 --- 1 F300 0
6791 Trip Delay On Evolving Faults 0 to 429496729 s 0.001 F001 0
6792 Trip Seal-In Delay 0 to 429496729 s 0.001 F001 0
6793 Trip Reset 0 to 2 --- 1 F609 0 (Pole Curr OR
Custom)
6794 Start Timer Zone 2 Phase Input 1 0 to 429496729 --- 1 F300 0
6796 Start Timer Zone 2 Phase Input 2 0 to 429496729 --- 1 F300 0
6798 Start Timer Zone 2 Ground Input 1 0 to 429496729 --- 1 F300 0
679A Start Timer Zone 2 Ground Input 2 0 to 429496729 --- 1 F300 0
679C Reserved (5 items) 0 to 1 --- 1 F001 0
Open Pole Detect (Read/Write Setting)
67B0 Open Pole Function 0 to 1 --- 1 F102 0 (Disabled)
67B1 Open Pole Block 0 to 4294967295 --- 1 F300 0
67B3 Open Pole Voltage Supervision 0 to 1 --- 1 F102 0 (Disabled)
67B4 Open Pole Current Pickup 0 to 30 pu 0.001 F001 50
67B5 Open Pole Target 0 to 2 --- 1 F109 0 (Self-reset)
67B6 Open Pole Events 0 to 1 --- 1 F102 0 (Disabled)
67B7 Open Pole Line XC0 300 to 9999.9 ohms 0.1 F003 99999
67B9 Open Pole Line XC1 300 to 9999.9 ohms 0.1 F003 99999
67BB Open Pole Remote Current Pickup 0 to 30 pu 0.001 F001 50
67BC Open Pole Detection 0 to 1 --- 1 F608 0 (I AND V AND
CBaux)
67BD Open Pole Mode 0 to 1 --- 1 F607 0 (Accelerated)
67BE Reserved (5 items) 0 to 1 --- 1 F001 0


Pilot DUTT (1P) (Read/Write Setting)
67D0 DUTT Function 0 to 1 --- 1 F102 0 (Disabled)
67D1 DUTT Seal In Delay 0 to 65.535 s 0.001 F001 0
67D2 DUTT 1P Number of Communication Bits 0 to 2 --- 1 F198 0 (1)
67D3 DUTT RX1 0 to 4294967295 --- 1 F300 0
67D5 DUTT RX2 0 to 4294967295 --- 1 F300 0
67D7 DUTT RX3 0 to 4294967295 --- 1 F300 0
67D9 DUTT RX4 0 to 4294967295 --- 1 F300 0
67DB DUTT 1P Target 0 to 2 --- 1 F109 0 (Self-reset)
67DC DUTT 1P Event 0 to 1 --- 1 F102 0 (Disabled)
B
67DD DUTT 1P Block 0 to 4294967295 --- 1 F300 0
67DF Reserved (6 items) 0 to 1 --- 1 F001 0
Pilot PUTT (1P) (Read/Write Setting)
67EA PUTT 1P Scheme Function 0 to 1 --- 1 F102 0 (Disabled)
67EB PUTT 1P Rx Pickup Delay 0 to 65.535 s 0.001 F001 0
67EC PUTT 1P Seal In Delay 0 to 65.535 s 0.001 F001 0
67ED PUTT 1P Number of Communication Bits 0 to 2 --- 1 F198 0 (1)
67EE PUTT 1P Rx1 0 to 4294967295 --- 1 F300 0
67F0 PUTT 1P Rx2 0 to 4294967295 --- 1 F300 0
67F2 PUTT 1P Rx3 0 to 4294967295 --- 1 F300 0
67F4 PUTT 1P Rx4 0 to 4294967295 --- 1 F300 0
67F6 PUTT 1P Target 0 to 2 --- 1 F109 0 (Self-reset)
67F7 PUTT 1P Event 0 to 1 --- 1 F102 0 (Disabled)
67F8 PUTT 1P Block 0 to 4294967295 --- 1 F300 0
67FA Reserved (5 items) 0 to 1 --- 1 F001 0
Pilot Hybrid POTT (1P) (Read/Write Setting)
6820 Hybrid POTT 1P Scheme Function 0 to 1 --- 1 F102 0 (Disabled)
6821 Hybrid POTT 1P Permissive Echo 0 to 2 --- 1 F199 0 (Disabled)
6822 Hybrid POTT 1P Rx Pickup Delay 0 to 65.535 s 0.001 F001 0
6823 Hybrid POTT 1P Trans Block Pickup Delay 0 to 65.535 s 0.001 F001 20
6824 Hybrid POTT 1P Trans Block Reset Delay 0 to 65.535 s 0.001 F001 90
6825 Hybrid POTT 1P Echo Duration 0 to 65.535 s 0.001 F001 100
6826 Hybrid POTT 1P Echo Lockout 0 to 65.535 s 0.001 F001 250
6827 Hybrid POTT 1P Seal In Delay 0 to 65.535 --- 0.001 F001 0
6828 Hybrid POTT 1P Ground Directional Overcurrent Forward 0 to 4294967295 --- 1 F300 0
682A Hybrid POTT 1P Gnd Directional Overcurrent Reverse 0 to 4294967295 --- 1 F300 0
682C Hybrid POTT 1P Number of Communication Bits 0 to 2 --- 1 F198 0 (1)
682D Hybrid POTT 1P Rx1 0 to 4294967295 --- 1 F300 0
682F Hybrid POTT 1P Rx2 0 to 4294967295 --- 1 F300 0
6831 Hybrid POTT 1P Rx3 0 to 4294967295 --- 1 F300 0
6833 Hybrid POTT 1P Rx4 0 to 4294967295 --- 1 F300 0
6835 Hybrid POTT 1P Target 0 to 2 --- 1 F109 0 (Self-reset)
6836 Hybrid POTT 1P Event 0 to 1 --- 1 F102 0 (Disabled)
68737 Hybrid POTT 1P Echo Condition 0 to 4294967295 --- 1 F300 0
6839 Hybrid POTT 1P Weak Infeed 0 to 2 --- 1 F199 1 (Enabled)
683A Hybrid POTT 1P Weak Infeed Condition 0 to 4294967295 --- 1 F300 0
683C Hybrid POTT 1P Block 0 to 4294967295 --- 1 F300 0
Pilot Blocking (1P) (Read/Write Setting)
6845 Blocking Scheme 1P Function 0 to 1 --- 1 F102 0 (Disabled)
6846 Block 1P Rx Coord Pickup Delay 0 to 65.535 s 0.001 F001 10
6847 Block 1P Transient Block Pickup Delay 0 to 65.535 s 0.001 F001 30
6848 Block 1P Transient Block Reset Delay 0 to 65.535 s 0.001 F001 90
6849 Blocking Scheme 1P Seal In Delay 0 to 65.535 s 0.001 F001 0


684A Blocking Scheme 1P Gnd Directional Overcurrent Fwd 0 to 4294967295 --- 1 F300 0
684C Blocking Scheme 1P Gnd Directional Overcurrent Rev 0 to 4294967295 --- 1 F300 0
684E Blocking Scheme 1P Number of Communication Bits 0 to 2 --- 1 F198 0 (1)
684F Blocking Scheme 1P Rx1 0 to 4294967295 --- 1 F300 0
6851 Blocking Scheme 1P Rx2 0 to 4294967295 --- 1 F300 0
6857 Blocking 1P Target 0 to 2 --- 1 F109 0 (Self-reset)
6858 Blocking 1P Event 0 to 1 --- 1 F102 0 (Disabled)
6859 Blocking Scheme 1P Block 0 to 4294967295 --- 1 F300 0
685B Reserved (2 items) 0 to 1 --- 1 F001 0
Autoreclose 1P 3P (Read/Write Setting) B
6860 Autoreclose Mode 0 to 3 --- 1 F080 0 (1 & 3 Pole)
6861 Autoreclose Maximum Number of Shots 1 to 4 --- 1 F001 2
6862 Autoreclose Block Breaker 1 0 to 4294967295 --- 1 F300 0
6864 Autoreclose Close Time Breaker 1 0 to 655.35 s 0.01 F001 10
6865 Autoreclose Breaker Manual Close 0 to 4294967295 --- 1 F300 0
6867 Autoreclose Function 0 to 1 --- 1 F102 0 (Disabled)
6868 Autoreclose Block Time Manual Close 0 to 655.35 s 0.01 F001 1000
6869 Autoreclose 1P Initiate 0 to 4294967295 --- 1 F300 0
686B Autoreclose 3P Initiate 0 to 4294967295 --- 1 F300 0
686D Autoreclose 3P TD Initiate 0 to 4294967295 --- 1 F300 0
686F Autoreclose Multi-Phase Fault 0 to 4294967295 --- 1 F300 0
6871 Autoreclose Breaker 1 Pole Open 0 to 4294967295 --- 1 F300 0
6873 Autoreclose Breaker 3 Pole Open 0 to 4294967295 --- 1 F300 0
6875 Autoreclose 3-Pole Dead Time 1 0 to 655.35 s 0.01 F001 50
6876 Autoreclose 3-Pole Dead Time 2 0 to 655.35 s 0.01 F001 120
6877 Autoreclose Extend Dead T1 0 to 4294967295 --- 1 F300 0
6879 Autoreclose Dead T1 Extension 0 to 655.35 s 0.01 F001 50
687A Autoreclose Reset 0 to 4294967295 --- 1 F300 0
687C Autoreclose Reset Time 0 to 655.35 s 0.01 F001 6000
687D Autoreclose Breaker Closed 0 to 4294967295 --- 1 F300 0
687F Autoreclose Block 0 to 4294967295 --- 1 F300 0
6881 Autoreclose Pause 0 to 4294967295 --- 1 F300 0
6883 Autoreclose Incomplete Sequence Time 0 to 655.35 s 0.01 F001 500
6884 Autoreclose Block Breaker 2 0 to 4294967295 --- 1 F300 0
6886 Autoreclose Close Time Breaker 2 0 to 655.35 s 0.01 F001 10
6887 Autoreclose Transfer 1 to 2 0 to 1 --- 1 F126 0 (No)
6888 Autoreclose Transfer 2 to 1 0 to 1 --- 1 F126 0 (No)
6889 Autoreclose Breaker 1 Fail Option 0 to 1 --- 1 F081 0 (Continue)
688A Autoreclose Breaker 2 Fail Option 0 to 1 --- 1 F081 0 (Continue)
688B Autoreclose 1P Dead Time 0 to 655.35 s 0.01 F001 100
688C Autoreclose Breaker Sequence 0 to 4 --- 1 F082 3 (1 - 2)
688D Autoreclose Transfer Time 0 to 655.35 s 0.01 F001 400
688E Autoreclose Event 0 to 1 --- 1 F102 0 (Disabled)
688F Autoreclose 3P Dead Time 3 0 to 655.35 s 0.01 F001 200
6890 Autoreclose 3P Dead Time 4 0 to 655.35 s 0.01 F001 400
6891 Autoreclose Bus Fault Initiate 0 to 4294967295 s 0.01 F300 0
6893 Autoreclose Initiate Mode 0 to 1 --- 1 F610 0 (Protection AND
CB)
6894 Autoreclose Mode Aut 0 to 3 --- 1 F622 0 (Mode 1 (1 & 3
Pole))
6895 Autoreclose Mode 1 Activation 0 to 4294967295 --- 1 F300 0


689B Autoreclose Mode 4 Activation 0 to 4294967295 --- 1 F300 0
Pilot Directional Comparison Unblocking Scheme (Read/Write Setting)
68A0 Directional Comparison Unblocking Scheme Function 0 to 1 --- 1 F102 0 (Disabled)
68A1 Directional Comparison Unblocking Block 0 to 4294967295 --- 1 F300 0
68A3 Directional Comparison Unblocking Permissive Echo 0 to 2 --- 1 F199 0 (Disabled)
68A4 Directional Comparison Unblocking Echo Condition 0 to 4294967295 --- 1 F300 0
68A6 DCUB Ground Directional Overcurrent Forward 0 to 4294967295 --- 1 F300 0
68A8 DCUB Ground Directional Overcurrent Reverse 0 to 4294967295 --- 1 F300 0
68AA DCUB Transmit Block Pickup Delay 0 to 65.535 s 0.001 F001 20
68AB DCUB Transmit Block Reset Delay 0 to 65.535 s 0.001 F001 90
B
68AC Directional Comparison Unblocking Echo Duration 0 to 65.535 s 0.001 F001 100
68AD Directional Comparison Unblocking Echo Lockout 0 to 65.535 s 0.001 F001 250
68AE DCUB Line End Open Pickup Delay 0 to 65.535 s 0.001 F001 50
68AF DCUB Loss-of-Guard Pickup Delay 0 to 65.535 s 0.001 F001 8
68B0 DCUB Guard Healthy Reset Delay 0 to 65.535 s 0.001 F001 15
68B1 DCUB Loss-of-Guard Trip Window 0 to 65.535 s 0.001 F001 150
68B2 Directional Comparison Unblocking Seal-In Delay 0 to 65.535 s 0.001 F001 10
68B3 Directional Comparison Unblocking Communication Bits 0 to 2 --- 1 F198 0 (1 bit)
68B4 Directional Comparison Unblocking Rx1 0 to 4294967295 --- 1 F300 0
68B6 Directional Comparison Unblocking LOG1 0 to 4294967295 --- 1 F300 0
68B8 Directional Comparison Unblocking Rx2 0 to 4294967295 --- 1 F300 0
68BA Directional Comparison Unblocking LOG2 0 to 4294967295 --- 1 F300 0
68BC Directional Comparison Unblocking Rx3 0 to 4294967295 --- 1 F300 0
68BE Directional Comparison Unblocking LOG3 0 to 4294967295 --- 1 F300 0
68C0 Directional Comparison Unblocking Rx4 0 to 4294967295 --- 1 F300 0
68C2 Directional Comparison Unblocking LOG4 0 to 4294967295 --- 1 F300 0
68C4 Directional Comparison Unblocking Target 0 to 2 --- 1 F109 0 (Self-Reset)
68C5 Directional Comparison Unblocking Event 0 to 1 -- 1 F102 0 (Disabled)
68C6 Reserved (6 items) 0 to 1 -- 1 F001 0
Phase Undervoltage (Read/Write Grouped Setting) (2 modules)
7000 Phase Undervoltage 1 Function 0 to 1 --- 1 F102 0 (Disabled)
7001 Phase Undervoltage 1 Signal Source 0 to 5 --- 1 F167 0 (SRC 1)
7002 Phase Undervoltage 1 Pickup 0 to 3 pu 0.001 F001 1000
7003 Phase Undervoltage 1 Curve 0 to 1 --- 1 F111 0 (Definite Time)
7004 Phase Undervoltage 1 Delay 0 to 600 s 0.01 F001 100
7005 Phase Undervoltage 1 Minimum Voltage 0 to 3 pu 0.001 F001 100
7006 Phase Undervoltage 1 Block 0 to 4294967295 --- 1 F300 0
7008 Phase Undervoltage 1 Target 0 to 2 --- 1 F109 0 (Self-reset)
7009 Phase Undervoltage 1 Events 0 to 1 --- 1 F102 0 (Disabled)
700A Phase Undervoltage 1 Measurement Mode 0 to 1 --- 1 F186 0 (Phase to
Ground)
700A Reserved (6 items) 0 to 1 --- 1 F001 0
7013 ...Repeated for Phase Undervoltage 2
701B ...Repeated for Phase Undervoltage 2
701C ...Repeated for Phase Undervoltage 2
702A ...Repeated for Phase Undervoltage 3
Phase Overvoltage (Read/Write Grouped Setting)
7040 Phase Overvoltage 1 Function 0 to 1 --- 1 F102 0 (Disabled)


7041 Phase Overvoltage 1 Source 0 to 5 --- 1 F167 0 (SRC 1)
7042 Phase Overvoltage 1 Pickup 0 to 3 pu 0.001 F001 1000
7043 Phase Overvoltage 1 Delay 0 to 600 s 0.01 F001 100
7044 Phase Overvoltage 1 Reset Delay 0 to 600 s 0.01 F001 100
7045 Phase Overvoltage 1 Block 0 to 4294967295 --- 1 F300 0
7047 Phase Overvoltage 1 Target 0 to 2 --- 1 F109 0 (Self-reset)
7048 Phase Overvoltage 1 Events 0 to 1 --- 1 F102 0 (Disabled)
Distance (Read/Write Grouped Setting)
7060 Distance Signal Source 0 to 5 --- 1 F167 0 (SRC 1)
7061 Memory Duration 5 to 25 cycles 1 F001 10
7062 Force Self-Polarization 0 to 4294967295 --- 1 F300 0 B
7064 Force Memory Polarization 0 to 4294967295 --- 1 F300 0
Phase Distance (Read/Write Grouped Setting) (5 modules)
7070 Phase Distance Zone 1 Function 0 to 1 --- 1 F102 0 (Disabled)
7071 Phase Distance Zone 1 Current Supervision 0.05 to 30 pu 0.001 F001 200
7072 Phase Distance Zone 1 Reach 0.02 to 500 ohms 0.01 F001 200
7073 Phase Distance Zone 1 Direction 0 to 2 --- 1 F154 0 (Forward)
7074 Phase Distance Zone 1 Comparator Limit 30 to 90 degrees 1 F001 90
7075 Phase Distance Zone 1 Delay 0 to 65.535 s 0.001 F001 0
7076 Phase Distance Zone 1 Block 0 to 4294967295 --- 1 F300 0
7078 Phase Distance Zone 1 Target 0 to 2 --- 1 F109 0 (Self-reset)
7079 Phase Distance Zone 1 Events 0 to --- 1 F102 0 (Disabled)
707A Phase Distance Zone 1 Shape 0 to 1 --- 1 F120 0 (Mho)
707B Phase Distance Zone 1 RCA 30 to 90 degrees 1 F001 85
707C Phase Distance Zone 1 DIR RCA 30 to 90 degrees 1 F001 85
707D Phase Distance Zone 1 DIR Comp Limit 30 to 90 degrees 1 F001 90
707E Phase Distance Zone 1 Quad Right Blinder 0.02 to 500 ohms 0.01 F001 1000
707F Phase Distance Zone 1 Quad Right Blinder RCA 60 to 90 degrees 1 F001 85
7080 Phase Distance Zone 1 Quad Left Blinder 0.02 to 500 ohms 0.01 F001 1000
7081 Phase Distance Zone 1 Quad Left Blinder RCA 60 to 90 degrees 1 F001 85
7082 Phase Distance Zone 1 Volt Limit 0 to 5 pu 0.001 F001 0
7083 Phase Distance Zone 1 Transformer Voltage Connection 0 to 12 --- 1 F153 0 (None)
7084 Phase Distance Zone 1 Transformer Current Connection 0 to 12 --- 1 F153 0 (None)
7085 Phase Distance Zone 1 Rev Reach 0.02 to 500 ohms 0.01 F001 200
7086 Phase Distance Zone 1 Rev Reach RCA 30 to 90 degrees 1 F001 85
7087 Reserved (10 items) --- --- --- F001 0
7091 ...Repeated for Phase Distance Zone 2
709A ...Repeated for Phase Distance Zone 2
709B ...Repeated for Phase Distance Zone 2
709D ...Repeated for Phase Distance Zone 2
709F ...Repeated for Phase Distance Zone 2
70A3 ...Repeated for Phase Distance Zone 2
70B2 ...Repeated for Phase Distance Zone 3


70BA ...Repeated for Phase Distance Zone 3
70BE ...Repeated for Phase Distance Zone 3
70C0 ...Repeated for Phase Distance Zone 3
70D3 ...Repeated for Phase Distance Zone 4
70D4 ...Repeated for Phase Distance Zone 4
B
70F4 ...Repeated for Phase Distance Zone 5
710A ...Repeated for Phase Distance Zone 5
Ground Distance (Read/Write Grouped Setting) (5 modules)
7130 Ground Distance Zone 1 Function 0 to 1 --- 1 F102 0 (Disabled)
7131 Ground Distance Zone 1 Current Supervision 0.05 to 30 pu 0.001 F001 200
7132 Ground Distance Zone 1 Reach 0.02 to 500 ohms 0.01 F001 200
7133 Ground Distance Zone 1 Direction 0 to 2 --- 1 F154 0 (Forward)
7134 Ground Distance Zone 1 Comparator Limit 30 to 90 degrees 1 F001 90
7135 Ground Distance Zone 1 Delay 0 to 65.535 s 0.001 F001 0
7136 Ground Distance Zone 1 Block 0 to 4294967295 --- 1 F300 0
7138 Ground Distance Zone 1 Target 0 to 2 --- 1 F109 0 (Self-reset)
7139 Ground Distance Zone 1 Events 0 to 1 --- 1 F102 0 (Disabled)
713A Ground Distance Zone 1 Shape 0 to 1 --- 1 F120 0 (Mho)
713B Ground Distance Zone 1 Z0 Z1 Magnitude 0 to 10 --- 0.01 F001 270
713C Ground Distance Zone 1 Z0 Z1 Angle -90 to 90 degrees 1 F002 0
713D Ground Distance Zone 1 RCA 30 to 90 degrees 1 F001 85
713E Ground Distance Zone 1 DIR RCA 30 to 90 degrees 1 F001 85
713F Ground Distance Zone 1 DIR Comp Limit 30 to 90 degrees 1 F001 90
7140 Ground Distance Zone 1 Quad Right Blinder 0.02 to 500 ohms 0.01 F001 1000
7141 Ground Distance Zone 1 Quad Right Blinder RCA 60 to 90 degrees 1 F001 85
7142 Ground Distance Zone 1 Quad Left Blinder 0.02 to 500 ohms 0.01 F001 1000
7143 Ground Distance Zone 1 Quad Left Blinder RCA 60 to 90 degrees 1 F001 85
7144 Ground Distance Zone 1 Z0M Z1 Magnitude 0 to 7 --- 0.01 F001 0
7145 Ground Distance Zone 1 Z0M Z1 Angle -90 to 90 degrees 1 F002 0
7146 Ground Distance Zone 1 Voltage Level 0 to 5 pu 0.001 F001 0
7147 Ground Distance Zone 1 Non-Homogeneous Angle -40 to 40 degrees 0.1 F002 0
7148 Ground Distance Zone 1 POL Current 0 to 1 --- 1 F521 0 (Zero-seq)
7149 Ground Distance Zone 1 Reverse Reach 0.02 to 500 ohms 0.01 F001 200
717A Ground Distance Zone 1 Reverse Reach RCA 30 to 90 degrees 1 F001 85
714B Reserved (7 items) 0 to 65535 --- 1 F001 0
7152 ...Repeated for Ground Distance Zone 2
716C ...Repeated for Ground Distance Zone 2
71B8 ...Repeated for Ground Distance Zone 5


Line Pickup (Read/Write Grouped Setting)
71E0 Line Pickup Function 0 to 1 --- 1 F102 0 (Disabled)
71E1 Line Pickup Signal Source 0 to 5 --- 1 F167 0 (SRC 1)
71E2 Line Pickup Phase IOC Pickup 0 to 30 pu 0.001 F001 1000
71E3 Line Pickup UV Pickup 0 to 3 pu 0.001 F001 700
71E4 Line End Open Pickup Delay 0 to 65.535 s 0.001 F001 150
71E5 Line End Open Reset Delay 0 to 65.535 s 0.001 F001 90
71E6 Line Pickup OV Pickup Delay 0 to 65.535 s 0.001 F001 40
71E7 Autoreclose Coordination Pickup Delay 0 to 65.535 s 0.001 F001 45
71E8 Autoreclose Coordination Reset Delay 0 to 65.535 s 0.001 F001 5
71E9 Autoreclose Coordination Bypass 0 to 1 --- 1 F102 1 (Enabled)
71EA Line Pickup Block 0 to 4294967295 --- 1 F300 0 B
71EC Line Pickup Target 0 to 2 --- 1 F109 0 (Self-reset)
71ED Line Pickup Events 0 to 1 --- 1 F102 0 (Disabled)
71EE Terminal Open 0 to 4294967295 --- 1 F300 0
71F0 Autoreclose Accelerate 0 to 4294967295 --- 1 F300 0
Phase Directional Overcurrent (Read/Write Grouped Setting) (2 modules)
7200 Phase Directional Overcurrent 1 Function 0 to 1 --- 1 F102 0 (Disabled)
7201 Phase Directional Overcurrent 1 Source 0 to 5 --- 1 F167 0 (SRC 1)
7202 Phase Directional Overcurrent 1 Block 0 to 4294967295 --- 1 F300 0
7204 Phase Directional Overcurrent 1 ECA 0 to 359 --- 1 F001 30
7205 Phase Directional Overcurrent 1 Pol V Threshold 0 to 3 pu 0.001 F001 700

7206 Phase Directional Overcurrent 1 Block Overcurrent 0 to 1 --- 1 F126 0 (No)
7207 Phase Directional Overcurrent 1 Target 0 to 2 --- 1 F109 0 (Self-reset)
7208 Phase Directional Overcurrent 1 Events 0 to 1 --- 1 F102 0 (Disabled)
7211 ...Repeated for Phase Directional Overcurrent 2
... ...Repeated for Phase Directional Overcurrent...
Neutral Directional Overcurrent (Read/Write Grouped Setting) (2 modules)
7230 Neutral Directional Overcurrent 1 Function 0 to 1 --- 1 F102 0 (Disabled)
7231 Neutral Directional Overcurrent 1 Source 0 to 5 --- 1 F167 0 (SRC 1)
7232 Neutral Directional Overcurrent 1 Polarizing 0 to 4 --- 1 F230 0 (Voltage)
7233 Neutral Directional Overcurrent 1 Forward ECA -90 to 90 ° Lag 1 F002 75
7234 Neutral Directional Overcurrent 1 Forward Limit Angle 40 to 90 degrees 1 F001 90
7235 Neutral Directional Overcurrent 1 Forward Pickup 0.006 to 30 pu 0.001 F001 50
7236 Neutral Directional Overcurrent 1 Reverse Limit Angle 40 to 90 degrees 1 F001 90
7237 Neutral Directional Overcurrent 1 Reverse Pickup 0.002 to 30 pu 0.001 F001 50
7238 Neutral Directional Overcurrent 1 Target 0 to 2 --- 1 F109 0 (Self-reset)
7239 Neutral Directional Overcurrent 1 Block 0 to 65535 --- 1 F300 0
723B Neutral Directional Overcurrent 1 Events 0 to 1 --- 1 F102 0 (Disabled)
723C Neutral Directional Overcurrent 1 Polarizing Voltage 0 to 1 --- 1 F231 0 (Calculated V0)
723D Neutral Directional Overcurrent 1 Op Current 0 to 1 --- 1 F196 0 (Calculated 3I0)
723E Neutral Directional Overcurrent 1 Offset 0 to 250 ohms 0.01 F001 0
723F Neutral Directional Overcurrent 1 Pos Seq Restraint 0 to 0.5 --- 0.001 F001 63
7240 Reserved 0 to 1 --- 1 F001 0
7241 ...Repeated for Neutral Directional Overcurrent 2
Negative-sequence directional overcurrent (read/write grouped settings) (2 modules)
7260 Negative Sequence Directional Overcurrent 1 Function 0 to 1 --- 1 F102 0 (Disabled)
7261 Negative Sequence Directional Overcurrent 1 Source 0 to 5 --- 1 F167 0 (SRC 1)
7262 Negative Sequence Directional Overcurrent 1 Type 0 to 1 --- 1 F179 0 (Neg Sequence)
7263 Neg Sequence Directional Overcurrent 1 Forward ECA 0 to 90 ° Lag 1 F002 75
7264 Neg Seq Directional Overcurrent 1 Forward Limit Angle 40 to 90 degrees 1 F001 90
7265 Neg Sequence Directional Overcurrent 1 Forward Pickup 0.015 to 30 pu 0.05 F001 5


7266 Neg Seq Directional Overcurrent 1 Reverse Limit Angle 40 to 90 degrees 1 F001 90
7267 Neg Sequence Directional Overcurrent 1 Reverse Pickup 0.015 to 30 pu 0.05 F001 5
7268 Negative Sequence Directional Overcurrent 1 Target 0 to 2 --- 1 F109 0 (Self-reset)
7269 Negative Sequence Directional Overcurrent 1 Block 0 to 4294967295 --- 1 F300 0
726B Negative Sequence Directional Overcurrent 1 Events 0 to 1 --- 1 F102 0 (Disabled)
726C Negative Sequence Directional Overcurrent 1 Offset 0 to 250 ohms 0.01 F001 0
726D Neg Seq Directional Overcurrent 1 Pos Seq Restraint 0 to 0.5 --- 0.001 F001 63
7271 ...Repeated for Neg Seq Directional Overcurrent 2
Disconnect Switch (Read/Write setting) (24 modules)
B
74A0 Disconnect switch 1 function 0 to 1 --- 1 F102 0 (Disabled)
74A1 Disconnect switch 1 name --- --- --- F206 “SW 1"
74A4 Disconnect switch 1 mode 0 to 1 --- 1 F157 0 (3-Pole)
74A5 Disconnect switch 1 open 0 to 4294967295 --- 1 F300 0
74A7 Disconnect switch 1 block open 0 to 4294967295 --- 1 F300 0
74A9 Disconnect switch 1 close 0 to 4294967295 --- 1 F300 0
74AB Disconnect switch 1 block close 0 to 4294967295 --- 1 F300 0
74AD Disconnect switch 1 phase A / three-pole closed 0 to 4294967295 --- 1 F300 0
74AF Disconnect switch 1 phase A / three-pole opened 0 to 4294967295 --- 1 F300 0
74B1 Disconnect switch 1 phase B closed 0 to 4294967295 --- 1 F300 0
74B3 Disconnect switch 1 phase B opened 0 to 4294967295 --- 1 F300 0
74B5 Disconnect switch 1 phase C closed 0 to 4294967295 --- 1 F300 0
74B7 Disconnect switch 1 phase C opened 0 to 4294967295 --- 1 F300 0
74B9 Disconnect switch 1 operate time 0 to 65.535 s 0.001 F001 70
74BA Disconnect switch 1 alarm delay 0 to 65.535 s 0.001 F003 0
74BC Disconnect switch 1 events 0 to 1 --- 1 F102 0 (Disabled)
74BD Reserved (2 items) --- --- --- --- ---
74BF ...Repeated for module number 2
Thermal Overload Protection (Read/Write Settings) (2 modules)
7788 Thermal Protection 1 Function 0 to 1 --- 1 F102 0 (Disabled)
7789 Thermal Protection 1 Source 0 to 5 --- 1 F167 0 (SRC 1)
778A Thermal Protection 1 Base Current 0.2 to 3 pu 0.01 F001 80
778B Thermal Protection 1 K Factor 1 to 1.2 --- 0.05 F001 110
778C Thermal Protection 1 Trip Time Constant 0 to 1000 min. 1 F001 45
778D Thermal Protection 1 Reset Time Constant 0 to 1000 min. 1 F001 45
778E Thermal Protection 1 Minimum Reset Time 0 to 1000 min. 1 F001 20
778F Thermal Protection 1 Reset 0 to 4294967295 --- 1 F300 0
7791 Thermal Protection 1 Block 0 to 4294967295 --- 1 F300 0
7793 Thermal Protection 1 Target 0 to 2 --- 1 F109 0 (Self-reset)
7794 Thermal Protection 1 Events 0 to 1 --- 1 F102 0 (Disabled)
7795 Reserved (2 items) --- --- --- F001 0
7797 Repeated for Thermal Protection 2
Broken conductor detection (Read/Write Settings) (6 modules)
77AA Broken Conductor 1 Function 0 to 1 --- 1 F102 0 (Disabled)
77AB Broken Conductor 1 Source 0 to 5 --- 1 F167 0 (SRC 1)
77AC Broken Conductor 1 I2/I1 Ratio 20 to 100 % 0.1 F001 200
77AD Broken Conductor 1 I1 Minimum 0.05 to 1 pu 0.01 F001 10
77AE Broken Conductor 1 I1 Maximum 0.05 to 5 pu 0.01 F001 150
77AF Broken Conductor 1 Pickup Delay 0 to 65.535 s 0.001 F001 20000
77B0 Broken Conductor 1 Block 0 to 4294967295 --- 1 F300 0
77B2 Broken Conductor 1 Target 0 to 2 --- 1 F109 0 (Self-reset)
77B3 Broken Conductor 1 Events 0 to 1 --- 1 F102 0 (Disabled)
77B4 Reserved (2 items) --- --- --- F001 0
77B6 ...Repeated for Broken Conductor 2


Ohm Inputs (Read/Write Setting) (2 modules)
77F8 Ohm Inputs 1 Function 0 to 1 --- 1 F102 0 (Disabled)
77F9 Ohm Inputs 1 ID --- --- --- F205 "Ohm Ip 1 "
77FF Ohm Inputs 1 Reserved (9 items) 0 to 65535 --- 1 F001 0
7808 ...Repeated for Ohm Inputs 2
Phasor Measurement Unit Recorder Config Counter Command (Read/Write Command) (4 modules)
781A PMU 1 Recorder Clear Config Counter 0 to 1 --- 1 F126 0 (No)
Phasor Measurement Unit Power Trigger (Read/Write Setting) (4 modules)
7820 PMU 1 Power Trigger Function 0 to 1 --- 1 F102 0 (Disabled)
7821 PMU 1 Power Trigger Active 0.25 to 3 pu 0.001 F001 1250
7822 PMU 1 Power Trigger Reactive 0.25 to 3 pu 0.001 F001 1250
7823 PMU 1 Power Trigger Apparent 0.25 to 3 pu 0.001 F001 1250 B
7824 PMU 1 Power Trigger Pickup Time 0 to 600 s 0.01 F001 10
7825 PMU 1 Power Trigger Dropout Time 0 to 600 s 0.01 F001 100
7826 PMU 1 Power Trigger Block (3 items) 0 to 4294967295 --- 1 F300 0
782C PMU 1 Power Trigger Target 0 to 2 --- 1 F109 0 (Self-reset)
782D PMU 1 Power Trigger Events 0 to 1 --- 1 F102 0 (Disabled)
Phasor Measurement Unit Voltage Trigger (Read/Write Setting) (4 modules)
7858 PMU 1 Voltage Trigger Function 0 to 1 --- 1 F102 0 (Disabled)
7859 PMU 1 Voltage Trigger Low Voltage 0.25 to 1.25 pu 0.001 F001 800
785A PMU 1 Voltage Trigger High Voltage 0.75 to 1.75 pu 0.001 F001 1200
785B PMU 1 Voltage Trigger Pickup Time 0 to 600 s 0.01 F001 10
785C PMU 1 Voltage Trigger Dropout Time 0 to 600 s 0.01 F001 100
785D PMU 1 Voltage Trigger Block (3 items) 0 to 4294967295 --- 1 F300 0
7863 PMU 1 Voltage Trigger Target 0 to 2 --- 1 F109 0 (Self-reset)
7864 PMU 1 Voltage Trigger Events 0 to 1 --- 1 F102 0 (Disabled)
Phasor Measurement Unit One-shot Command (Read/Write Setting)
78BC PMU One-shot Function 0 to 1 --- 1 F102 0 (Disabled)
78BD PMU One-shot Sequence Number 0 to 99 --- 1 F001 1
788E PMU One-shot Time 0 to 235959 --- 1 F050 0
Phasor Measurement Unit Test Values (Read/Write Setting)
7890 PMU 1 Test Function 0 to 1 --- 1 F102 0 (Disabled)
7891 PMU 1 Phase A Voltage Test Magnitude 0 to 700 kV 0.01 F003 50000
7893 PMU 1 Phase A Voltage Test Angle -180 to 180 ° 0.05 F002 0
7894 PMU 1 Phase B Voltage Test Magnitude 0 to 700 kV 0.01 F003 50000
7896 PMU 1 Phase B Voltage Test Angle -180 to 180 ° 0.05 F002 -12000
7897 PMU 1 Phase C Voltage Test Magnitude 0 to 700 kV 0.01 F003 50000
7899 PMU 1 Phase C Voltage Test Angle -180 to 180 ° 0.05 F002 120
789A PMU 1 Auxiliary Voltage Test Magnitude 0 to 700 kV 0.01 F003 50000
789C PMU 1 Auxiliary Voltage Test Angle -180 to 180 ° 0.05 F002 0
789D PMU 1 Phase A Current Test Magnitude 0 to 9.999 kA 0.001 F004 1000
789F PMU 1 Phase A Current Test Angle -180 to 180 ° 0.05 F002 -1000
78A0 PMU 1 Phase B Current Test Magnitude 0 to 9.999 kA 0.001 F004 1000
78A2 PMU 1 Phase B Current Test Angle -180 to 180 ° 0.05 F002 -13000
78A3 PMU 1 Phase C Current Test Magnitude 0 to 9.999 kA 0.001 F003 1000
78A5 PMU 1 Phase C Current Test Angle -180 to 180 ° 0.05 F002 11000
78A6 PMU 1 Ground Current Test Magnitude 0 to 9.999 kA 0.001 F004 0
78A8 PMU 1 Ground Current Test Angle -180 to 180 ° 0.05 F002 0
78A9 PMU 1 Test Frequency 20 to 70 Hz 0.001 F003 60000
78AB PMU 1 Test df/dt -10 to 10 Hz/s 0.01 F002 0
Phasor Measurement Unit Recording Values (Read Only) (4 modules)
7900 PMU 1 Available Records 0 to 65535 --- 1 F001 0
7901 PMU 1 Second Per Record 0 to 6553.5 --- 0.1 F001 0
7903 PMU 1 Last Cleared Date 0 to 400000000 --- 1 F050 0


Phasor Measurement Unit Network Reporting Configuration (Read/Write Setting)
7914 PMU Network Reporting Function 0 to 1 --- 1 F102 0 (Disabled)
7915 PMU Network Reporting ID Code 1 to 65534 --- 1 F001 1
7916 PMU TCP port number 1 to 65535 --- 1 F001 4712
7917 PMU UDP port number 1 1 to 65535 --- 1 F001 4713
7918 PMU UDP port number 2 1 to 65535 --- 1 F001 4714
Phasor Measurement Unit Calibration (Read/Write Setting) (4 modules)
7919 PMU Va Calibration Angle -5 to 5 ° 0.05 F002 0
791A PMU Va Calibration Magnitude 95 to 105 % 0.1 F002 1000
791B PMU Vb Calibration Angle -5 to 5 ° 0.05 F002 0
B
791C PMU Vb Calibration Magnitude 95 to 105 % 0.1 F002 1000
791D PMU Vc Calibration Angle -5 to 5 ° 0.05 F002 0
791E PMU Vc Calibration Magnitude 95 to 105 % 0.1 F002 1000
791F PMU Vx Calibration Angle -5 to 5 ° 0.05 F002 0
7920 PMU Vx Calibration Magnitude 95 to 105 % 0.1 F002 1000
7921 PMU Ia Calibration Angle -5 to 5 ° 0.05 F002 0
7922 PMU Ia Calibration Magnitude 95 to 105 % 0.1 F002 1000
7923 PMU Ib Calibration Angle -5 to 5 ° 0.05 F002 0
7924 PMU Ib Calibration Magnitude 95 to 105 % 0.1 F002 1000
7925 PMU Ic Calibration Angle -5 to 5 ° 0.05 F002 0
7926 PMU Ic Calibration Magnitude 95 to 105 % 0.1 F002 1000
7927 PMU Ig Calibration Angle -5 to 5 ° 0.05 F002 0
7928 PMU Ig Calibration Magnitude 95 to 105 % 0.1 F002 1000
7929 PMU Sequence Voltage Shift Angle -180 to 180 ° 30 F002 0
792A PMU Sequence Current Shift Angle -180 to 180 ° 30 F002 0
Phasor Measurement Unit Triggering (Read/Write Setting) (4 modules)
7970 PMU 1 User Trigger 0 to 4294967295 --- 1 F300 0
Phasor Measurement Unit Current Trigger (Read/Write Setting) (4 modules)
7980 PMU 1 Current Trigger Function 0 to 1 --- 1 F102 0 (Disabled)
7981 PMU 1 Current Trigger Pickup 0.1 to 30 pu 0.001 F001 1800
7982 PMU 1 Current Trigger Pickup Time 0 to 600 s 0.01 F001 10
7983 PMU 1 Current Trigger Dropout Time 0 to 600 s 0.01 F001 100
7984 PMU 1 Current Trigger Block (3 items) 0 to 4294967295 --- 1 F300 0
798A PMU 1 Current Trigger Target 0 to 2 --- 1 F109 0 (Self-reset)
798B PMU 1 Current Trigger Events 0 to 1 --- 1 F102 0 (Disabled)
Phasor Measurement Unit df/dt Trigger (Read/Write Setting)
79B0 PMU 1 df/dt Trigger Function 0 to 1 --- 1 F102 0 (Disabled)
79B1 PMU 1 df/dt Trigger Raise 0.1 to 15 Hz/s 0.01 F001 25
79B2 PMU 1 df/dt Trigger Fall 0.1 to 15 Hz/s 0.01 F001 25
79B3 PMU 1 df/dt Trigger Pickup Time 0 to 600 s 0.01 F001 10
79B4 PMU 1 df/dt Trigger Dropout Time 0 to 600 s 0.01 F001 100
79B5 PMU 1 df/dt Trigger Block (3 items) 0 to 4294967295 --- 1 F300 0
79BB PMU 1 df/dt Trigger Target 0 to 2 --- 1 F109 0 (Self-reset)
79BC PMU 1 df/dt Trigger Events 0 to 1 --- 1 F102 0 (Disabled)
Underfrequency (Read/Write Setting) (6 modules)
7A80 Underfreqency Function 0 to 1 --- 1 F102 0 (Disabled)
7A81 Underfrequency Block 0 to 4294967295 --- 1 F300 0
7A83 Min Current 0.1 to 1.25 pu 0.01 F001 10
7A84 Underfrequency Pickup 20 to 65 Hz 0.01 F001 5950
7A85 Pickup Delay 0 to 65.535 s 0.001 F001 2000
7A86 Reset Delay 0 to 65.535 s 0.001 F001 2000
7A87 Underfrequency Source 0 to 5 --- 1 F167 0 (SRC 1)
7A88 Underfrequency Events 0 to 1 --- 1 F102 0 (Disabled)
7A89 Underfrequency Target 0 to 2 --- 1 F109 0 (Self-reset)


7A8A Underfreqency 1 Reserved (5 items) 0 to 1 --- 1 F001 0
7A8F ...Repeated for Underfrequency 2
7A9E ...Repeated for Underfrequency 3
7AAD ...Repeated for Underfrequency 4
7ABC ...Repeated for Underfrequency 5
7ACB ...Repeated for Underfrequency 6
User Programmable Pushbuttons (Read/Write Setting) (16 modules)
7B60 User Programmable Pushbutton 1 Function 0 to 2 --- 1 F109 2 (Disabled)
7B61 User Programmable Pushbutton 1 Top Line --- --- --- F202 (none)
7B6B User Programmable Pushbutton 1 On Text --- --- --- F202 (none)
7B75 User Programmable Pushbutton 1 Off Text --- --- --- F202 (none)
7B7F User Programmable Pushbutton 1 Drop-Out Time 0 to 60 s 0.05 F001 0 B
7B80 User Programmable Pushbutton 1 Target 0 to 2 --- 1 F109 0 (Self-reset)
7B81 User Programmable Pushbutton 1 Events 0 to 1 --- 1 F102 0 (Disabled)
7B82 User Programmable Pushbutton 1 LED Operand 0 to 4294967295 --- 1 F300 0
7B84 User Programmable Pushbutton 1 Autoreset Delay 0 to 600 s 0.05 F001 0
7B85 User Programmable Pushbutton 1 Autoreset Function 0 to 1 --- 1 F102 0 (Disabled)
7B86 User Programmable Pushbutton 1 Local Lock 0 to 4294967295 --- 1 F300 0
7B88 User Programmable Pushbutton 1 Message Priority 0 to 2 --- 1 F220 0 (Disabled)
7B89 User Programmable Pushbutton 1 Remote Lock 0 to 4294967295 --- 1 F300 0
7B8B User Programmable Pushbutton 1 Reset 0 to 4294967295 --- 1 F300 0
7B8D User Programmable Pushbutton 1 Set 0 to 4294967295 --- 1 F300 0
7B8F User Programmable Pushbutton 1 Hold 0 to 10 s 0.1 F001 1
7B90 ...Repeated for User Programmable Pushbutton 2
7BC0 ...Repeated for User Programmable Pushbutton 3
7BF0 ...Repeated for User Programmable Pushbutton 4
7C20 ...Repeated for User Programmable Pushbutton 5
7CB0 ...Repeated for User Programmable Pushbutton 8
7DE0 ...Repeated for User Programmable Pushbutton 9
7D10 ...Repeated for User Programmable Pushbutton 10
7DA0 ...Repeated for User Programmable Pushbutton 13
7DD0 ...Repeated for User Programmable Pushbutton 14
7E00 ...Repeated for User Programmable Pushbutton 15
7E30 ...Repeated for User Programmable Pushbutton 16
Neutral Overvoltage (Read/Write Grouped Setting) (3 modules)
7F00 Neutral Overvoltage 1 Function 0 to 1 --- 1 F102 0 (Disabled)
7F01 Neutral Overvoltage 1 Signal Source 0 to 5 --- 1 F167 0 (SRC 1)
7F02 Neutral Overvoltage 1 Pickup 0 to 3.00 pu 0.001 F001 300
7F03 Neutral Overvoltage 1 Pickup Delay 0 to 600 s 0.01 F001 100
7F04 Neutral Overvoltage 1 Reset Delay 0 to 600 s 0.01 F001 100
7F05 Neutral Overvoltage 1 Block 0 to 4294967295 --- 1 F300 0
7F07 Neutral Overvoltage 1 Target 0 to 2 --- 1 F109 0 (Self-reset)
7F08 Neutral Overvoltage 1 Events 0 to 1 --- 1 F102 0 (Disabled)
7F09 Neutral Overvoltage 1 Curves 0 to 3 --- 1 F116 0 (Definite Time)
7F0A Reserved (8 items) 0 to 65535 --- 1 F001 0
7F11 ...Repeated for Neutral Overvoltage 2
7F22 ...Repeated for Neutral Overvoltage 3
Auxiliary Undervoltage (Read/Write Grouped Setting) (3 modules)
7F60 Auxiliary Undervoltage 1 Function 0 to 1 --- 1 F102 0 (Disabled)
7F61 Auxiliary Undervoltage 1 Signal Source 0 to 5 --- 1 F167 0 (SRC 1)


7F62 Auxiliary Undervoltage 1 Pickup 0 to 3 pu 0.001 F001 700
7F63 Auxiliary Undervoltage 1 Delay 0 to 600 s 0.01 F001 100
7F64 Auxiliary Undervoltage 1 Curve 0 to 1 --- 1 F111 0 (Definite Time)
7F65 Auxiliary Undervoltage 1 Minimum Voltage 0 to 3 pu 0.001 F001 100
7F66 Auxiliary Undervoltage 1 Block 0 to 4294967295 --- 1 F300 0
7F68 Auxiliary Undervoltage 1 Target 0 to 2 --- 1 F109 0 (Self-reset)
7F69 Auxiliary Undervoltage 1 Events 0 to 1 --- 1 F102 0 (Disabled)
7F6A Reserved (7 items) 0 to 65535 --- 1 F001 0
7F71 ...Repeated for Auxiliary Undervoltage 2
7F82 ...Repeated for Auxiliary Undervoltage 3
B
Auxiliary Overvoltage (Read/Write Grouped Setting) (3 modules)
7FA0 Auxiliary Overvoltage 1 Function 0 to 1 --- 1 F102 0 (Disabled)
7FA1 Auxiliary Overvoltage 1 Signal Source 0 to 5 --- 1 F167 0 (SRC 1)
7FA2 Auxiliary Overvoltage 1 Pickup 0 to 3 pu 0.001 F001 300
7FA3 Auxiliary Overvoltage 1 Pickup Delay 0 to 600 s 0.01 F001 100
7FA4 Auxiliary Overvoltage 1 Reset Delay 0 to 600 s 0.01 F001 100
7FA5 Auxiliary Overvoltage 1 Block 0 to 4294967295 --- 1 F300 0
7FA7 Auxiliary Overvoltage 1 Target 0 to 2 --- 1 F109 0 (Self-reset)
7FA8 Auxiliary Overvoltage 1 Events 0 to 1 --- 1 F102 0 (Disabled)
7FA9 Reserved (8 items) 0 to 65535 --- 1 F001 0
7FB1 ...Repeated for Auxiliary Overvoltage 2
7FC2 ...Repeated for Auxiliary Overvoltage 3
Frequency (Read Only)
8000 Tracking Frequency --- Hz --- F001 0
Temp Monitor Actual Values (Read Only Non-Volatile)
81C0 Reserved Register T1 -55 to 125 C 1 F002 -55
81C1 Reserved Register T2 -55 to 125 C 1 F002 125
81C2 Reserved Register T3 -2147483647 to --- 1 F004 0
2147483647
81C4 Reserved Register T4 0 to 4294967295 --- 1 F003 0
81CA Reserved Register T7 0 to 4294967295 --- 1 F003 0
81CC Reserved Register T8 0 to 4294967295 --- 1 F003 0
Breaker Failure (Read/Write Grouped Setting) (4 or 6 modules)
8600 Breaker Failure 1 Function 0 to 1 --- 1 F102 0 (Disabled)
8601 Breaker Failure 1 Mode 0 to 1 --- 1 F157 0 (3-Pole)
8602 Breaker Failure 1 Source 0 to 5 --- 1 F167 0 (SRC 1)
8603 Breaker Failure 1 Amp Supervision 0 to 1 --- 1 F126 1 (Yes)
8604 Breaker Failure 1 Use Seal-In 0 to 1 --- 1 F126 1 (Yes)
8605 Breaker Failure 1 Three Pole Initiate 0 to 4294967295 --- 1 F300 0
8607 Breaker Failure 1 Block 0 to 4294967295 --- 1 F300 0
8609 Breaker Failure 1 Phase Amp Supv Pickup 0.001 to 30 pu 0.001 F001 1050
860A Breaker Failure 1 Neutral Amp Supv Pickup 0.001 to 30 pu 0.001 F001 1050
860B Breaker Failure 1 Use Timer 1 0 to 1 --- 1 F126 1 (Yes)
860C Breaker Failure 1 Timer 1 Pickup 0 to 65.535 s 0.001 F001 0
860D Breaker Failure 1 Use Timer 2 0 to 1 --- 1 F126 1 (Yes)
860E Breaker Failure 1 Timer 2 Pickup 0 to 65.535 s 0.001 F001 0
860F Breaker Failure 1 Use Timer 3 0 to 1 --- 1 F126 1 (Yes)
8610 Breaker Failure 1 Timer 3 Pickup 0 to 65.535 s 0.001 F001 0
8611 Breaker Failure 1 Breaker Status 1 Phase A/3P 0 to 4294967295 --- 1 F300 0
8613 Breaker Failure 1 Breaker Status 2 Phase A/3P 0 to 4294967295 --- 1 F300 0
8615 Breaker Failure 1 Breaker Test On 0 to 4294967295 --- 1 F300 0
8617 Breaker Failure 1 Phase Amp Hiset Pickup 0.001 to 30 pu 0.001 F001 1050


8618 Breaker Failure 1 Neutral Amp Hiset Pickup 0.001 to 30 pu 0.001 F001 1050
8619 Breaker Failure 1 Phase Amp Loset Pickup 0.001 to 30 pu 0.001 F001 1050
861A Breaker Failure 1 Neutral Amp Loset Pickup 0.001 to 30 pu 0.001 F001 1050
861B Breaker Failure 1 Loset Time 0 to 65.535 s 0.001 F001 0
861C Breaker Failure 1 Trip Dropout Delay 0 to 65.535 s 0.001 F001 0
861D Breaker Failure 1 Target 0 to 2 --- 1 F109 0 (Self-reset)
861E Breaker Failure 1 Events 0 to 1 --- 1 F102 0 (Disabled)
861F Breaker Failure 1 Phase A Initiate 0 to 4294967295 --- 1 F300 0
8621 Breaker Failure 1 Phase B Initiate 0 to 4294967295 --- 1 F300 0
8623 Breaker Failure 1 Phase C Initiate 0 to 4294967295 --- 1 F300 0
8625 Breaker Failure 1 Breaker Status 1 Phase B 0 to 4294967295 --- 1 F300 0
8627 Breaker Failure 1 Breaker Status 1 Phase C 0 to 4294967295 --- 1 F300 0 B
8629 Breaker Failure 1 Breaker Status 2 Phase B 0 to 4294967295 --- 1 F300 0
862B Breaker Failure 1 Breaker Status 2 Phase C 0 to 4294967295 --- 1 F300 0
862D ...Repeated for Breaker Failure 2
865A ...Repeated for Breaker Failure 3
8687 ...Repeated for Breaker Failure 4
86B4 ...Repeated for Breaker Failure 5
86E1 ...Repeated for Breaker Failure 6
FlexState Settings (Read/Write Setting)
8800 FlexState Parameters (256 items) 0 to 4294967295 --- --- F300 0
Digital Elements (Read/Write Setting) (48 modules)
8A00 Digital Element 1 Function 0 to 1 --- 1 F102 0 (Disabled)
8A01 Digital Element 1 Name --- --- --- F203 “Dig Element 1“
8A09 Digital Element 1 Input 0 to 4294967295 --- 1 F300 0
8A0B Digital Element 1 Pickup Delay 0 to 999999.999 s 0.001 F003 0
8A0D Digital Element 1 Reset Delay 0 to 999999.999 s 0.001 F003 0
8A0F Digital Element 1 Block 0 to 4294967295 --- 1 F300 0
8A11 Digital Element 1 Target 0 to 2 --- 1 F109 0 (Self-reset)
8A12 Digital Element 1 Events 0 to 1 --- 1 F102 0 (Disabled)
8A13 Digital Element 1 Pickup LED 0 to 1 --- 1 F102 1 (Enabled)
8A14 Reserved (2 items) --- --- --- F001 0
8A16 ...Repeated for Digital Element 2
8A2C ...Repeated for Digital Element 3
8A6E ...Repeated for Digital Element 6
8A9A ...Repeated for Digital Element 8
8AB0 ...Repeated for Digital Element 9
8AC6 ...Repeated for Digital Element 10
8ADC ...Repeated for Digital Element 11
8AF2 ...Repeated for Digital Element 12
8B08 ...Repeated for Digital Element 13
8B1E ...Repeated for Digital Element 14
8B4A ...Repeated for Digital Element 16
8B8C ...Repeated for Digital Element 19
8BA2 ...Repeated for Digital Element 20
8BB8 ...Repeated for Digital Element 21
8BCE ...Repeated for Digital Element 22
8BE4 ...Repeated for Digital Element 23


8BFA ...Repeated for Digital Element 24
8C10 ...Repeated for Digital Element 25
8C3C ...Repeated for Digital Element 27
8C7E ...Repeated for Digital Element 30
8CAA ...Repeated for Digital Element 32
8CC0 ...Repeated for Digital Element 33
B
8CD6 ...Repeated for Digital Element 34
8CEC ...Repeated for Digital Element 35
8D02 ...Repeated for Digital Element 36
8D2E ...Repeated for Digital Element 38
8D5A ...Repeated for Digital Element 40
8D9C ...Repeated for Digital Element 43
8DB2 ...Repeated for Digital Element 44
8DC8 ...Repeated for Digital Element 45
8DDE ...Repeated for Digital Element 46
8DF4 ...Repeated for Digital Element 47
8E0A ...Repeated for Digital Element 48
Trip Bus (Read/Write Setting) (6 modules)
8E00 Trip Bus 1 Function 0 to 1 --- 1 F102 0 (Disabled)
8ED1 Trip Bus 1 Block 0 to 4294967295 --- --- F300 0
8ED3 Trip Bus 1 Pickup Delay 0 to 600 s 0.01 F001 0
8ED4 Trip Bus 1 Reset Delay 0 to 600 s 0.01 F001 0
8ED5 Trip Bus 1 Input (16 items) 0 to 4294967295 --- 1 F300 0
8EF5 Trip Bus 1 Latching 0 to 1 --- 1 F102 0 (Disabled)
8EF6 Trip Bus 1 Reset 0 to 65535 --- 1 F300 0
8EF8 Trip Bus 1 Target 0 to 2 --- 1 F109 0 (Self-reset)
8EF9 Trip Bus 1 Events 0 to 1 --- 1 F102 0 (Disabled)
8EFA Reserved (8 items) --- --- --- F001 0
8F02 ...Repeated for Trip Bus 2
8FCA ...Repeated for Trip Bus 6
FlexElement (Read/Write Setting) (16 modules)
9000 FlexElement 1 Function 0 to 1 --- 1 F102 0 (Disabled)
9001 FlexElement 1 Name --- --- --- F206 “FxE 1”
9004 FlexElement 1 InputP 0 to 65535 --- 1 F600 0
9005 FlexElement 1 InputM 0 to 65535 --- 1 F600 0
9006 FlexElement 1 Compare 0 to 1 --- 1 F516 0 (LEVEL)
9007 FlexElement 1 Input 0 to 1 --- 1 F515 0 (SIGNED)
9008 FlexElement 1 Direction 0 to 1 --- 1 F517 0 (OVER)
9009 FlexElement 1 Hysteresis 0.1 to 50 % 0.1 F001 30
900A FlexElement 1 Pickup -90 to 90 pu 0.001 F004 1000
900C FlexElement 1 DeltaT Units 0 to 2 --- 1 F518 0 (Milliseconds)
900D FlexElement 1 DeltaT 20 to 86400 --- 1 F003 20
900F FlexElement 1 Pickup Delay 0 to 65.535 s 0.001 F001 0


9010 FlexElement 1 Reset Delay 0 to 65.535 s 0.001 F001 0
9011 FlexElement 1 Block 0 to 65535 --- 1 F300 0
9013 FlexElement 1 Target 0 to 2 --- 1 F109 0 (Self-reset)
9014 FlexElement 1 Events 0 to 1 --- 1 F102 0 (Disabled)
9015 ...Repeated for FlexElement 2
902A ...Repeated for FlexElement 3
903F ...Repeated for FlexElement 4
907E ...Repeated for FlexElement 7
90A8 ...Repeated for FlexElement 9 B
90BD ...Repeated for FlexElement 10
90D2 ...Repeated for FlexElement 11
90E7 ...Repeated for FlexElement 12
90FC ...Repeated for FlexElement 13
913B ...Repeated for FlexElement16
Fault Report Settings (Read/Write Setting) (up to 5 modules)
9200 Fault Report 1 Source 0 to 5 --- 1 F167 0 (SRC 1)
9201 Fault Report 1 Trigger 0 to 4294967295 --- 1 F300 0
9203 Fault Report 1 Z1 Magnitude 0.01 to 250 ohms 0.01 F001 300
9204 Fault Report 1 Z1 Angle 25 to 90 degrees 1 F001 75
9205 Fault Report 1 Z0 Magnitude 0.01 to 650 ohms 0.01 F001 900
9206 Fault Report 1 Z0 Angle 25 to 90 degrees 1 F001 75
9207 Fault Report 1 Line Length Units 0 to 1 --- 1 F147 0 (km)
9208 Fault Report 1 Line Length 0 to 2000 0.1 F001 1000
9209 Fault Report 1 VT Substitution 0 to 2 --- 1 F270 0 (None)
920A Fault Report 1 System Z0 Magnitude 0.01 to 650.00 ohms 0.01 F001 900
9208 Fault Report 1 System Z0 Angle 25 to 90 degrees 1 F001 75
920C Fault REM1-TAP Z1 Magnitude 0.01 to 250 ohms 0.01 F001 300
920D Fault REM1-TAP Z1 Angle 25 to 90 degrees 1 F001 75
920E Fault REM1-TAP Length 0 to 2000 --- 0.1 F001 1000
920F Fault REM2-TAP Z1 Magnitude 0.01 to 250 ohms 0.01 F001 300
9210 Fault REM2-TAP Z1 Angle 25 to 90 degrees 1 F001 75
9511 Fault REM2-TAP Length 0 to 2000 --- 0.1 F001 1000
9212 ...Repeated for Fault Report 2
dcmA Outputs (Read/Write Setting) (24 modules)
9360 dcmA Output 1 Source 0 to 65535 --- 1 F600 0
9361 dcmA Output 1 Range 0 to 2 --- 1 F522 0 (–1 to 1 mA)
9362 dcmA Output 1 Minimum –90 to 90 pu 0.001 F004 0
9364 dcmA Output 1 Maximum –90 to 90 pu 0.001 F004 1000
9366 ...Repeated for dcmA Output 2
936C ...Repeated for dcmA Output 3
937E ...Repeated for dcmA Output 6
938A ...Repeated for dcmA Output 8


939C ...Repeated for dcmA Output 11
93A2 ...Repeated for dcmA Output 12
93A8 ...Repeated for dcmA Output 13
93AE ...Repeated for dcmA Output 14
93B4 ...Repeated for dcmA Output 15
93BA ...Repeated for dcmA Output 16
93C0 ...Repeated for dcmA Output 17
93C6 ...Repeated for dcmA Output 18
93CC ...Repeated for dcmA Output 19
B
93D2 ...Repeated for dcmA Output 20
93D8 ...Repeated for dcmA Output 21
93DE ...Repeated for dcmA Output 22
93E4 ...Repeated for dcmA Output 23
93EA ...Repeated for dcmA Output 24
Direct Input/Output Names (Read/Write Setting) (96 modules)
9400 Direct Input 1 Name 0 to 96 --- 1 F205 “Dir Ip 1”
9406 Direct Output 1 Name 1 to 96 --- 1 F205 “Dir Out 1”
940C ...Repeated for Direct Input/Output 2
9418 ...Repeated for Direct Input/Output 3
94A8 ...Repeated for Direct Input/Output 15
94B4 ...Repeated for Direct Input/Output 16
94C0 ...Repeated for Direct Input/Output 17
94CC ...Repeated for Direct Input/Output 18
94D8 ...Repeated for Direct Input/Output 19
94E4 ...Repeated for Direct Input/Output 20
94F0 ...Repeated for Direct Input/Output 21
94FC ...Repeated for Direct Input/Output 22
IEC 61850 Received Integers (Read/Write Setting) (16 modules)
98A0 IEC61850 GOOSE UInteger 1 default value 0 to 429496295 --- 1 F003 1000
98A2 IEC61850 GOOSE UInteger input 1 mode 0 to 1 --- 1 F491 0 (Default
Value)
98A3 ...Repeated for IEC61850 GOOSE UInteger 2


98AC ...Repeated for IEC61850 GOOSE UInteger 5
98AF ...Repeated for IEC61850 GOOSE UInteger 6
98B2 ...Repeated for IEC61850 GOOSE UInteger 7
98BB ...Repeated for IEC61850 GOOSE UInteger 10
98BE ...Repeated for IEC61850 GOOSE UInteger 11
98C1 ...Repeated for IEC61850 GOOSE UInteger 12
98C4 ...Repeated for IEC61850 GOOSE UInteger 13
98C7 ...Repeated for IEC61850 GOOSE UInteger 14 B
98CA ...Repeated for IEC61850 GOOSE UInteger 15
98CD ...Repeated for IEC61850 GOOSE UInteger 16
FlexElement Actuals (Read Only) (16 modules)
9000 FlexElement 1 Actual -2147483.647 to 2147483.647 --- 0.001 F004 0
990A FlexElement 6 Actual -2147483.647 to 2147483.647 --- 0.001 F004 0
990C FlexElement 7 Actual -2147483.647 to 2147483.647 --- 0.001 F004 0
990E FlexElement 8 Actual -2147483.647 to 2147483.647 --- 0.001 F004 0
Breaker Restrike (Read/Write Setting) (3 modules)
9930 Breaker restrike 1 function 0 to 1 --- 1 F102 0 (Disabled)
9931 Breaker restrike 1 block 0 to 4294967295 --- 1 F300 0
9933 Breaker restrike 1 signal source 0 to 5 --- 1 F167 0 (SRC 1)
9934 Breaker restrike 1 pickup 0.10 to 2.00 pu 0.01 F001 500
9935 Breaker restrike 1 reset delay 0 to 65.535 s 0.001 F001 100
9936 Breaker restrike 1 HF detect 0 to 1 --- 1 F102 1 (Enabled)
9937 Breaker restrike 1 breaker open 0 to 4294967295 --- 1 F300 0
9939 Breaker restrike 1 open command 0 to 4294967295 --- 1 F300 0
993B Breaker restrike 1 close command 0 to 4294967295 --- 1 F300 0
993D Breaker restrike 1 target 0 to 2 --- 1 F109 0 (Self-reset)
993E Breaker restrike 1 events 0 to 1 --- 1 F102 0 (Disabled)
993F Reserved (2 items) 0 to 1 --- 1 F001 0
9941 ...Repeated for breaker restrike 2
Teleprotection Inputs/Outputs Commands (Read/Write Command)
9980 Teleprotection Clear Lost Packets 0 to 1 --- 1 F126 0 (No)
Teleprotection Inputs/Outputs (Read/Write Settings)
9990 Teleprotection Function 0 to 1 --- 1 F102 0 (Disabled)
9991 Teleprotection Number of Terminals 2 to 3 --- 1 F001 2
9992 Teleprotection Number of Channels 1 to 2 --- 1 F001 1
9993 Teleprotection Local Relay ID 0 to 255 --- 1 F001 0
9994 Teleprotection Terminal 1 ID 0 to 255 --- 1 F001 0
9995 Teleprotection Terminal 2 ID 0 to 255 --- 1 F001 0
9996 Reserved (10 items) 0 to 1 --- --- F001 0
9A00 Teleprotection Input 1-n Default States (16 items) 0 to 3 --- 1 F086 0 (Off)
9A10 Teleprotection Input 2-n Default States (16 items) 0 to 3 --- 1 F086 0 (Off)
9A20 Teleprotection Output 1-n Operand (16 items) 0 to 4294967295 --- 1 F300 0
9A40 Teleprotection Output 2-n Operand (16 items) 0 to 4294967295 --- 1 F300 0
Teleprotection Channel Tests (Read Only)
9AA0 Teleprotection Channel 1 Status 0 to 2 --- 1 F134 1 (OK)
9AA1 Teleprotection Channel 1 Number of Lost Packets 0 to 65535 --- 1 F001 0


9AA2 Teleprotection Channel 2 Status 0 to 2 --- 1 F134 1 (OK)
9AA3 Teleprotection Channel 2 Number of Lost Packets 0 to 65535 --- 1 F001 0
9AA4 Teleprotection Network Status 0 to 2 --- 1 F134 2 (n/a)
9AAF Teleprotection Channel 1 Input States 0 to 1 --- 1 F500 0
9AB0 Teleprotection Channel 2 Input States 0 to 1 --- 1 F500 0
9AC0 Teleprotection Input 1 States, 1 per register (16 items) 0 to 1 --- 1 F108 0 (Off)
9AD0 Teleprotection Input 2 States, 1 per register (16 items) 0 to 1 --- 1 F108 0 (Off)
VT Fuse Failure (Read/Write Setting) (6 modules)
A09A VT Fuse Failure Function 0 to 1 --- 1 F102 0 (Disabled)
A09B VT Fuse Failure Neutral Wire Open Function 0 to 1 --- 1 F102 0 (Disabled)
B
A09C VT Fuse Failure Neutral Wire Open 3rd Harmonic Pickup 0 to 3 pu 0.001 F001 100
A09D ...Repeated for module number 2
A0A0 ...Repeated for module number 3
A0AC VTFF x V0 3rd harmonic 0 to 999999.999 V 0.001 F060 0
Selector switch actual values (read only)
A210 Selector switch 1 position 1 to 7 --- 1 F001 0
A211 Selector switch 2 position 1 to 7 --- 1 F001 1
Selector switch settings (read/write, 2 modules)
A280 Selector 1 Function 0 to 1 --- 1 F102 0 (Disabled)
A281 Selector 1 Range 1 to 7 --- 1 F001 7
A282 Selector 1 Timeout 3 to 60 s 0.1 F001 50
A283 Selector 1 Step Up 0 to 4294967295 --- 1 F300 0
A285 Selector 1 Step Mode 0 to 1 --- 1 F083 0 (Time-out)
A286 Selector 1 Acknowledge 0 to 4294967295 --- 1 F300 0
A288 Selector 1 Bit0 0 to 4294967295 --- 1 F300 0
A28A Selector 1 Bit1 0 to 4294967295 --- 1 F300 0
A28C Selector 1 Bit2 0 to 4294967295 --- 1 F300 0
A28E Selector 1 Bit Mode 0 to 1 --- 1 F083 0 (Time-out)
A28F Selector 1 Bit Acknowledge 0 to 4294967295 --- 1 F300 0
A291 Selector 1 Power Up Mode 0 to 2 --- 1 F084 0 (Restore)
A292 Selector 1 Target 0 to 2 --- 1 F109 0 (Self-reset)
A293 Selector 1 Events 0 to 1 --- 1 F102 0 (Disabled)
A294 Reserved (10 items) --- --- 1 F001 0
A29E ...Repeated for Selector 2
Digital Counter (Read/Write Setting) (8 modules)
A300 Digital Counter 1 Function 0 to 1 --- 1 F102 0 (Disabled)
A301 Digital Counter 1 Name --- --- --- F205 “Counter 1"
A307 Digital Counter 1 Units --- --- --- F206 (none)
A30A Digital Counter 1 Block 0 to 4294967295 --- 1 F300 0
A30C Digital Counter 1 Up 0 to 4294967295 --- 1 F300 0
A30E Digital Counter 1 Down 0 to 4294967295 --- 1 F300 0
A311 Digital Counter 1 Preset –2147483647 to --- 1 F004 0
2147483647
A313 Digital Counter 1 Compare –2147483647 to --- 1 F004 0
2147483647
A315 Digital Counter 1 Reset 0 to 4294967295 --- 1 F300 0
A317 Digital Counter 1 Freeze/Reset 0 to 4294967295 --- 1 F300 0
A319 Digital Counter 1 Freeze/Count 0 to 4294967295 --- 1 F300 0
A31B Digital Counter 1 Set To Preset 0 to 4294967295 --- 1 F300 0
A31D Reserved (11 items) --- --- --- F001 0
A328 ...Repeated for Digital Counter 2


A3A0 ...Repeated for Digital Counter 5
A3C8 ...Repeated for Digital Counter 6
A3F0 ...Repeated for Digital Counter 7
Flexcurves C and D (Read/Write Setting)
A600 FlexCurve C (120 items) 0 to 65535 ms 1 F011 0
A680 FlexCurve D (120 items) 0 to 65535 ms 1 F011 0
Non Volatile Latches (Read/Write Setting) (16 modules)
A700 Non-Volatile Latch 1 Function 0 to 1 --- 1 F102 0 (Disabled)
A701 Non-Volatile Latch 1 Type 0 to 1 --- 1 F519 0 (Reset
A702 Non-Volatile Latch 1 Set 0 to 4294967295 --- 1 F300

Dominant)
0
B
A704 Non-Volatile Latch 1 Reset 0 to 4294967295 --- 1 F300 0
A706 Non-Volatile Latch 1 Target 0 to 2 --- 1 F109 0 (Self-reset)
A707 Non-Volatile Latch 1 Events 0 to 1 --- 1 F102 0 (Disabled)
A708 Reserved (4 items) --- --- --- F001 0
A70C ...Repeated for Non-Volatile Latch 2
A718 ...Repeated for Non-Volatile Latch 3
A7A8 ...Repeated for Non-Volatile Latch 15
A7B4 ...Repeated for Non-Volatile Latch 16
Pilot POTT (1P) (Read/Write Setting)
A800 POTT 1P Scheme Function 0 to 1 --- 1 F102 0 (Disabled)
A801 POTT 1P Permissive Echo 0 to 2 --- 1 F199 0 (Disabled)
A802 POTT 1P Rx Pickup Delay 0 to 65.535 s 0.001 F001 0
A803 POTT 1P Trans Block Pickup Delay 0 to 65.535 s 0.001 F001 20
A804 POTT 1P Trans Block Reset Delay 0 to 65.535 s 0.001 F001 90
A805 POTT 1P Echo Duration 0 to 65.535 s 0.001 F001 100
A806 POTT 1P Echo Lockout 0 to 65.535 s 0.001 F001 250
A807 POTT 1P Line End Open Pickup Delay 0 to 65.535 s 0.001 F001 50
A808 POTT 1P Seal In Delay 0 to 65.535 s 0.001 F001 0
A809 POTT 1P Ground Directional Overcurrent Forward 0 to 4294967295 --- 1 F300 0
A80B POTT 1P Number of Communication Bits 0 to 2 --- 1 F198 0 (1)
A80C POTT 1P Rx1 0 to 4294967295 --- 1 F300 0
A80E POTT 1P Rx2 0 to 4294967295 --- 1 F300 0
A810 POTT 1P Rx3 0 to 4294967295 --- 1 F300 0
A812 POTT 1P Rx4 0 to 4294967295 --- 1 F300 0
A814 POTT 1P Target 0 to 2 --- 1 F109 0 (Self-reset)
A815 POTT 1P Event 0 to 1 --- 1 F102 0 (Disabled)
A816 POTT 1P Echo Condition 0 to 4294967295 --- 1 F300 0
A818 POTT 1P Scheme Block 0 to 4294967295 --- 1 F300 0
A81A Reserved (22 items) 0 to 1 --- 1 F001 0


Pilot POTT1 (1P) (Read/Write Setting)
A830 POTT1 1P Scheme Function 0 to 1 --- 1 F102 0 (Disabled)
A831 POTT1 1P Permissive Echo 0 to 2 --- 1 F199 0 (Disabled)
A832 POTT1 1P Rx Pickup Delay 0 to 65.535 s 0.001 F001 0
A833 POTT1 1P Trans Block Pickup Delay 0 to 65.535 s 0.001 F001 20
A834 POTT1 1P Trans Block Reset Delay 0 to 65.535 s 0.001 F001 90
A835 POTT1 1P Echo Duration 0 to 65.535 s 0.001 F001 100
A836 POTT1 1P Echo Lockout 0 to 65.535 s 0.001 F001 250
A837 POTT1 1P Line End Open Pickup Delay 0 to 65.535 s 0.001 F001 50
A838 POTT1 1P Seal In Delay 0 to 65.535 s 0.001 F001 0
B
A839 POTT1 1P Ground Directional Overcurrent Forward 0 to 4294967295 --- 1 F300 0
A83B POTT1 1P Number of Communication Bits 0 to 2 --- 1 F198 0 (1)
A83C POTT1 1P Rx1 0 to 4294967295 --- 1 F300 0
A83E POTT1 1P Rx2 0 to 4294967295 --- 1 F300 0
A840 POTT1 1P Rx3 0 to 4294967295 --- 1 F300 0
A842 POTT1 1P Rx4 0 to 4294967295 --- 1 F300 0
A844 POTT1 1P Target 0 to 2 --- 1 F109 0 (Self-reset)
A845 POTT1 1P Event 0 to 1 --- 1 F102 0 (Disabled)
A846 POTT1 1P Echo Condition 0 to 4294967295 --- 1 F300 0
A848 POTT1 1P Scheme Block 0 to 4294967295 --- 1 F300 0
A84A POTT1 1P OC Fwd2 0 to 4294967295 --- 1 F300 0
A84C POTT1 1P OC Fwd2 0 to 4294967295 --- 1 F300 0
A84E Reserved (22 items) 0 to 1 --- 1 F001 0
Frequency Rate of Change (Read/Write Setting) (4 modules)
A900 Frequency Rate of Change 1 Function 0 to 1 --- 1 F102 0 (Disabled)
A901 Frequency Rate of Change 1 OC Supervision 0 to 30 pu 0.001 F001 200
A902 Frequency Rate of Change 1 Min 20 to 80 Hz 0.01 F001 4500
A903 Frequency Rate of Change 1 Max 20 to 80 Hz 0.01 F001 6500
A904 Frequency Rate of Change 1 Pickup Delay 0 to 65.535 s 0.001 F001 0
A905 Frequency Rate of Change 1 Reset Delay 0 to 65.535 s 0.001 F001 0
A906 Frequency Rate of Change 1 Block 0 to 4294967295 --- 1 F300 0
A908 Frequency Rate of Change 1 Target 0 to 2 --- 1 F109 0 (Self-reset)
A909 Frequency Rate of Change 1 Events 0 to 1 --- 1 F102 0 (Disabled)
A90A Frequency Rate of Change 1 Source 0 to 5 --- 1 F167 0 (SRC 1)
A90B Frequency Rate of Change 1 Trend 0 to 2 --- 1 F224 0 (Increasing)
A90C Frequency Rate of Change 1 Pickup 0.1 to 15 Hz/s 0.01 F001 50
A90D Frequency Rate of Change 1 OV Supervision 0.1 to 3 pu 0.001 F001 700
A90E Frequency Rate of Change 1 Reserved (3 items) 0 to 1 --- 1 F001 0
A911 ...Repeated for Frequency Rate of Change 2
IEC 61850 received analog settings (read/write) (32 modules)
AA00 IEC 61850 GOOSE analog 1 default value –1000000 to 1000000 --- 0.001 F060 1000
AA02 IEC 61850 GOOSE analog input 1 mode 0 to 1 --- 1 F491 0 (Default Value)
AA03 IEC 61850 GOOSE analog input 1 units --- --- --- F207 (none)
AA05 IEC 61850 GOOSE analog input 1 per-unit base 0 to 999999999.999 --- 0.001 F060 1
AA07 ...Repeated for IEC 61850 GOOSE analog input 2
AA0E ...Repeated for IEC 61850 GOOSE analog input 3
AA1C ...Repeated for IEC 61850 GOOSE analog input 5
AA2A ...Repeated for IEC 61850 GOOSE analog input 7


AA3F ...Repeated for IEC 61850 GOOSE analog input 10
AA4D ...Repeated for IEC 61850 GOOSE analog input 12
AA5B ...Repeated for IEC 61850 GOOSE analog input 14
AA7E ...Repeated for IEC 61850 GOOSE analog input 19
AA8C ...Repeated for IEC 61850 GOOSE analog input 21 B
AA9A ...Repeated for IEC 61850 GOOSE analog input 23
AAA1 ...Repeated for IEC 61850 GOOSE analog input 24
AAA8 ...Repeated for IEC 61850 GOOSE analog input 25
AAAF ...Repeated for IEC 61850 GOOSE analog input 26
AAB6 ...Repeated for IEC 61850 GOOSE analog input 27
AABD ...Repeated for IEC 61850 GOOSE analog input 28
AAC4 ...Repeated for IEC 61850 GOOSE analog input 29
AACB ...Repeated for IEC 61850 GOOSE analog input 30
AAD2 ...Repeated for IEC 61850 GOOSE analog input 31
AAD9 ...Repeated for IEC 61850 GOOSE analog input 32
IEC 61850 XCBR configuration (read/write settings) (6 modules)
AB00 Operand for IEC 61850 XCBR1.ST.Loc status 0 to 4294967295 --- 1 F300 0
AB02 Command to clear XCBR1 OpCnt (operation counter) 0 to 1 --- 1 F126 0 (No)
AB03 Operand for IEC 61850 XCBR Check Sync Release 0 to 4294967295 --- 1 F300 0
AB05 Operand for IEC 6185 XCBR Open Interlock 0 to 4294967295 --- 1 F300 0
AB06 Operand for IEC 61850 XCBR3.ST.Loc status 0 to 4294967295 --- 1 F300 0
AB07 Operand for IEC 61850 XCBR Close Interlock 0 to 4294967295 --- 1 F300 0
AB09 Operand for IEC 61850 XCBR Pos ct1Model 0 to 4 --- 1 F001 2
AB0A Operand for IEC 61850 XCBR Pos sboTimeout 2 to 60 s 1 F001 30
AB0B ...Repeated for Module 2
AB16 ...Repeated for Module 3

AB2C ...Repeated for Module 5
IEC 61850 LN name prefixes (read/write settings)
AB48 IEC 61850 logical node LPHD1 name prefix 0 to 65534 --- 1 F206 (none)
AB4B IEC 61850 logical node PIOCx name prefix (72 items) 0 to 65534 --- 1 F206 (none)
AC23 IEC 61850 logical node PTOCx name prefix (24 items) 0 to 65534 --- 1 F206 (none)
AC6B IEC 61850 logical node PTUVx name prefix (13 items) 0 to 65534 --- 1 F206 (none)
AC92 IEC 61850 logical node PTOVx name prefix (10 items) 0 to 65534 --- 1 F206 (none)
ACB0 IEC 61850 logical node PDISx name prefix (10 items) 0 to 65534 --- 1 F206 (none)
ACCE IEC 61850 logical node RBRFx name prefix (24 items) 0 to 65534 --- 1 F206 (none)
AD16 IEC 61850 logical node RPSBx name prefix 0 to 65534 --- 1 F206 (none)
AD19 IEC 61850 logical node RRECx name prefix (6 items) 0 to 65534 --- 1 F206 (none)
AD2B IEC 61850 logical node MMXUx name prefix (6 items) 0 to 65534 --- 1 F206 (none)
AD3D IEC 61850 logical node GGIOx name prefix (5 items) 0 to 65534 --- 1 F206 (none)
AD4C IEC 61850 logical node RFLOx name prefix (5 items) 0 to 65534 --- 1 F206 (none)
AD5B IEC 61850 logical node XCBRx name prefix (6 items) 0 to 65534 --- 1 F206 (none)
AD6D IEC 61850 logical node PTRCx name prefix (6 items) 0 to 65534 --- 1 F206 (none)
AD7F IEC 61850 logical node PDIFx name prefix (6 items) 0 to 65534 --- 1 F206 (none)


AD8B IEC 61850 logical node MMXNx name prefix (6 items) 0 to 65534 --- 1 F206 (none)
ADFA IEC 61850 logical node CSWIx name prefix (6 items) 0 to 65534 --- 1 F206 (none)
AE54 IEC 61850 logical node XSWIx name prefix (6 items) 0 to 65534 --- 1 F206 (none)
IEC 61850 GGIO4 general analog configuration settings (read/write)
AF00 Number of analog points in GGIO4 4 to 32 --- 4 F001 4
AF01 GOOSE analog scan period 100 to 5000 --- 10 F001 1000
IEC 61850 GGIO4 analog input points configuration settings (read/write)
AF10 IEC 61850 GGIO4 analog input 1 value --- --- --- F600 0
AF11 IEC 61850 GGIO4 analog input 1 deadband 0.001 to 100 % 0.001 F003 100000
AF13 IEC 61850 GGIO4 analog input 1 minimum –1000000000000 to --- 0.001 F060 0
1000000000000
B AF15 IEC 61850 GGIO4 analog input 1 maximum –1000000000000 to

1000000000000
--- 0.001 F060 1000000
AF17 ...Repeated for IEC 61850 GGIO4 analog input 2

AF1E ...Repeated for IEC 61850 GGIO4 analog input 3
AF2C ...Repeated for IEC 61850 GGIO4 analog input 5
AF3A ...Repeated for IEC 61850 GGIO4 analog input 7
AF4F ...Repeated for IEC 61850 GGIO4 analog input 10
AF5D ...Repeated for IEC 61850 GGIO4 analog input 12
AF6B ...Repeated for IEC 61850 GGIO4 analog input 14
AF8E ...Repeated for IEC 61850 GGIO4 analog input 19
AF9C ...Repeated for IEC 61850 GGIO4 analog input 21
AFA3 ...Repeated for IEC 61850 GGIO4 analog input 22
AFAA ...Repeated for IEC 61850 GGIO4 analog input 23
AFB1 ...Repeated for IEC 61850 GGIO4 analog input 24
AFB8 ...Repeated for IEC 61850 GGIO4 analog input 25
AFBF ...Repeated for IEC 61850 GGIO4 analog input 26
AFC6 ...Repeated for IEC 61850 GGIO4 analog input 27
AFCD ...Repeated for IEC 61850 GGIO4 analog input 28
AFD4 ...Repeated for IEC 61850 GGIO4 analog input 29
AFDB ...Repeated for IEC 61850 GGIO4 analog input 30
AFE2 ...Repeated for IEC 61850 GGIO4 analog input 31
AFE9 ...Repeated for IEC 61850 GGIO4 analog input 32
IEC 61850 GOOSE/GSSE Configuration (Read/Write Setting)
B01C Default GOOSE/GSSE Update Time 1 to 60 s 1 F001 60
B01D IEC 61850 GSSE Function (GsEna) 0 to 1 --- 1 F102 1 (Enabled)
B013 IEC 61850 GSSE ID --- --- --- F209 “GSSEOut”
B03F IEC 61850 GOOSE Function (GoEna) 0 to 1 --- 1 F102 0 (Disabled)
B040 IEC 61850 GSSE Destination MAC Address --- --- --- F072 0
B043 IEC 61850 Standard GOOSE ID --- --- --- F209 “GOOSEOut”
B064 IEC 61850 Standard GOOSE Destination MAC Address --- --- --- F072 0
B067 IEC 61850 GOOSE VLAN Transmit Priority 0 to 7 --- 1 F001 4
B068 IEC 61850 GOOSE VLAN ID 0 to 4095 --- 1 F001 0
B069 IEC 61850 GOOSE ETYPE APPID 0 to 16383 --- 1 F001 0


B06A Reserved (2 items) 0 to 1 --- 1 F001 0
IEC 61850 Server Configuration (Read/Write Settings/Commands)
B06C TCP Port Number for the IEC 61850 / MMS Protocol 0 to 65535 --- 1 F001 102
B06D IEC 61850 Logical Device Name --- --- --- F213 “IECName”
B07D IEC 61850 Logical Device Instance --- --- --- F213 “LDInst”
B08D IEC 61850 LPHD Location --- --- --- F204 “Location”
B0B5 Include non-IEC 61850 Data 0 to 1 --- 1 F102 0 (Disabled)
B0B6 IEC 61850 Server Data Scanning Function 0 to 1 --- 1 F102 0 (Disabled)
B0B7 IEC 61850 LPHD Latitude -90000 to 90000 degree 1 F004 0
B0B9 IEC 61850 LPHD DC PhyNam Longitude -180000 to 180000 degree 1 F004 0
B9BB IEC 61850 LPHD DC PhyNam Altitude 0 to 10000 m 1 F003 0
B0BD Reserved (3 items) 0 to 1 --- 1 F001 0 B
IEC 61850 MMXU Deadbands (Read/Write Setting) (6 modules)
B0C0 IEC 61850 MMXU TotW Deadband 1 0.001 to 100 % 0.001 F003 10000
B0C2 IEC 61850 MMXU TotVAr Deadband 1 0.001 to 100 % 0.001 F003 10000
B0C4 IEC 61850 MMXU TotVA Deadband 1 0.001 to 100 % 0.001 F003 10000
B0C6 IEC 61850 MMXU TotPF Deadband 1 0.001 to 100 % 0.001 F003 10000
B0C8 IEC 61850 MMXU Hz Deadband 1 0.001 to 100 % 0.001 F003 10000
B0CA IEC 61850 MMXU PPV.phsAB Deadband 1 0.001 to 100 % 0.001 F003 10000
B0CC IEC 61850 MMXU PPV.phsBC Deadband 1 0.001 to 100 % 0.001 F003 10000
B0CE IEC 61850 MMXU PPV.phsCA Deadband 1 0.001 to 100 % 0.001 F003 10000
B0D0 IEC 61850 MMXU PhV.phsADeadband 1 0.001 to 100 % 0.001 F003 10000
B0D2 IEC 61850 MMXU PhV.phsB Deadband 1 0.001 to 100 % 0.001 F003 10000
B0D4 IEC 61850 MMXU PhV.phsC Deadband 1 0.001 to 100 % 0.001 F003 10000
B0D6 IEC 61850 MMXU A.phsA Deadband 1 0.001 to 100 % 0.001 F003 10000
B0D8 IEC 61850 MMXU A.phsB Deadband 1 0.001 to 100 % 0.001 F003 10000
B0DA IEC 61850 MMXU A.phsC Deadband 1 0.001 to 100 % 0.001 F003 10000
B0DC IEC 61850 MMXU A.neut Deadband 1 0.001 to 100 % 0.001 F003 10000
B0DE IEC 61850 MMXU W.phsA Deadband 1 0.001 to 100 % 0.001 F003 10000
B0E0 IEC 61850 MMXU W.phsB Deadband 1 0.001 to 100 % 0.001 F003 10000
B0E2 IEC 61850 MMXU W.phsC Deadband 1 0.001 to 100 % 0.001 F003 10000
B0E4 IEC 61850 MMXU VAr.phsA Deadband 1 0.001 to 100 % 0.001 F003 10000
B0E6 IEC 61850 MMXU VAr.phsB Deadband 1 0.001 to 100 % 0.001 F003 10000
B0E8 IEC 61850 MMXU VAr.phsC Deadband 1 0.001 to 100 % 0.001 F003 10000
B0EA IEC 61850 MMXU VA.phsA Deadband 1 0.001 to 100 % 0.001 F003 10000
B0EC IEC 61850 MMXU VA.phsB Deadband 1 0.001 to 100 % 0.001 F003 10000
B0EE IEC 61850 MMXU VA.phsC Deadband 1 0.001 to 100 % 0.001 F003 10000
B0F0 IEC 61850 MMXU PF.phsA Deadband 1 0.001 to 100 % 0.001 F003 10000
B0F2 IEC 61850 MMXU PF.phsB Deadband 1 0.001 to 100 % 0.001 F003 10000
B0F4 IEC 61850 MMXU PF.phsC Deadband 1 0.001 to 100 % 0.001 F003 10000
B0F6 ...Repeated for Deadband 2
B12C ...Repeated for Deadband 3
B162 ...Repeated for Deadband 4
B198 ...Repeated for Deadband 5
B1CE ...Repeated for Deadband 6
IEC 61850 Received Analogs (Read Only) (32 modules)
B210 IEC 61850 Received Analog 1 -1000000000000 to --- 0.001 F060 0
1000000000000
B212 ...Repeated for Received Analog 2
B21A ...Repeated for Received Analog 6
B21C ...Repeated for Received Analog 7


B21E ...Repeated for Received Analog 8
B
IEC 61850 Configurable Report Settings (Read/Write Setting)
B290 IEC 61850 configurable reports dataset items (64 items) 0 to 848 --- 1 F615 0 (None)
Wattmetric ground fault settings (read/write grouped, 2 modules)
B300 Wattmetric ground fault 1 function 0 to 1 --- 1 F102 0 (Disabled)
B301 Wattmetric ground fault 1 source 0 to 5 --- 1 F167 0 (SRC 1)
B302 Wattmetric ground fault 1 voltage 0 to 1 --- 1 F234 0 (Calculated VN)
B303 Wattmetric ground fault 1 overvoltage pickup 0.02 to 3.00 pu 0.01 F001 20
B304 Wattmetric ground fault 1 current 0 to 1 --- 1 F235 (Calculated IN)
B305 Wattmetric ground fault 1 overcurrent pickup 0.002 to 30.000 pu 0.001 F001 60
B306 Wattmetric ground fault 1 overcurrent pickup delay 0 to 600 s 0.01 F001 20
B307 Wattmetric ground fault 1 power pickup 0.001 to 1.2 pu 0.001 F001 100
B308 Wattmetric ground fault 1 ECA 0 to 360 ° Lag 1 F001 0
B309 Wattmetric ground fault 1 power pickup delay 0 to 600 s 0.01 F001 20
B30A Wattmetric ground fault 1 curve 0 to 5 --- 1 F236 0 (Definite Time)
B30B Wattmetric ground fault 1 multiplier 0.01 to 2 s 0.01 F001 100
B30C Wattmetric ground fault 1 block 0 to 65535 --- 1 F300 0
B30E Wattmetric ground fault 1 target 0 to 2 --- 1 F109 0 (Self-reset)
B30F Wattmetric ground fault 1 events 0 to 1 --- 1 F102 0 (Disabled)
B310 Wattmetric ground fault 1 reference power 0.001 to 1.2 pu 0.001 F001 500
B311 Wattmetric ground fault x Reserved 0 to 1 --- 1 F001 0
B312 ...Repeated for wattmetric ground fault 2
Wattmetric ground fault actual values (read only) (5 modules)
B360 Wattmetric ground fault 1 operating power 0 to 999999.999 W 0.001 F060 0


IEC 61850 XSWI Configuration (Read/Write Setting) (24 modules)
B370 Flexlogic Operand for IEC 61850 XSWI.ST.Loc Status 0 to 4294967295 --- 1 F300 0
IEC 61850 XSWI Configuration (Read/Write Command) (24 modules)
B372 Command to Clear XSWI OpCnt (Operation Counter) 0 to 1 --- 1 F126 0 (No)
IEC 61850 GGIO1 Configuration Settings (Read/Write Setting)
B400 Number of Status Indications in GGIO1 8 to 128 --- 8 F001 8
B402 IEC 61850 GGIO1 Indication FlexLogic operands (128 0 to 4294967295 --- 1 F300 0
items)
IEC 61850 Configurable GOOSE Transmission (Read/Write Setting) (8 modules)
B5A0 IEC 61850 Configurable GOOSE Function 0 to 1 --- 1 F102 0 (None)
B5A1
B5C2
IEC 61850 Configurable GOOSE ID
Configurable GOOSE Destination MAC Address
---
---
---
---
---
---
F209
F072
“GOOSEOut_x_”
0
B
B5C5 IEC 61850 Configurable GOOSE VLAN Transmit Priority 0 to 7 --- 1 F001 4
B5C6 IEC 61850 Configurable GOOSE VLAN ID 0 to 4095 --- 1 F001 0
B5C7 IEC 61850 Configurable GOOSE ETYPE APPID 0 to 16383 --- 1 F001 0
B5C8 IEC 61850 Configurable GOOSE ConfRev 1 to 4294967295 --- 1 F003 1
B5CA IEC 61850 Configurable GOOSE Retransmission Curve 0 to 3 --- 1 F611 3 (Relaxed)
B5CB Configurable GOOSE dataset items for transmission 0 to 542 --- 1 F616 0 (None)
(64 items)
B60B ...Repeated for Module 2
B676 ...Repeated for Module 3
B6E1 ...Repeated for Module 4
B74C ...Repeated for Module 5
B7B7 ...Repeated for Module 6
B88D ...Repeated for Module 8
IEC 61850 Configurable GOOSE Reception (Read/Write Setting) (16 modules)
B900 Configurable GOOSE dataset items for reception 0 to 197 --- 1 F233 0 (None)
(32 items)
B9A0 ...Repeated for Module 6
B9C0 ...Repeated for Module 7
B9E0 ...Repeated for Module 8
BA00 ...Repeated for Module 9
BAA0 ...Repeated for Module 14
BAC0 ...Repeated for Module 15
BAE0 ...Repeated for Module 16
Contact Inputs (Read/Write Setting) (96 modules)
BB00 Contact Input 1 Name --- --- --- F205 “Cont Ip 1“
BB06 Contact Input 1 Events 0 to 1 --- 1 F102 0 (Disabled)
BB07 Contact Input 1 Debounce Time 0 to 16 ms 0.5 F001 20
BB08 ...Repeated for Contact Input 2


B
BBA0 ...Repeated for Contact Input 21
BBA8 ...Repeated for Contact Input 22
BBB0 ...Repeated for Contact Input 23
BBB8 ...Repeated for Contact Input 24
BBC0 ...Repeated for Contact Input 25
BBC8 ...Repeated for Contact Input 26
BBD0 ...Repeated for Contact Input 27
BBD8 ...Repeated for Contact Input 28
BBE0 ...Repeated for Contact Input 29
BBE8 ...Repeated for Contact Input 30
BBF0 ...Repeated for Contact Input 31
BBF8 ...Repeated for Contact Input 32
BC00 ...Repeated for Contact Input 33
BCA0 ...Repeated for Contact Input 53
BCA8 ...Repeated for Contact Input 54
BCB0 ...Repeated for Contact Input 55
BCB8 ...Repeated for Contact Input 56
BCC0 ...Repeated for Contact Input 57
BCC8 ...Repeated for Contact Input 58
BCD0 ...Repeated for Contact Input 59
BCD8 ...Repeated for Contact Input 60
BCE0 ...Repeated for Contact Input 61


BCE8 ...Repeated for Contact Input 62
BCF0 ...Repeated for Contact Input 63
BCF8 ...Repeated for Contact Input 64
BD00 ...Repeated for Contact Input 65
BD40 ...Repeated for Contact Input 73 B
BDA0 ...Repeated for Contact Input 85
BDA8 ...Repeated for Contact Input 86
BDB0 ...Repeated for Contact Input 87
BDB8 ...Repeated for Contact Input 88
BDC0 ...Repeated for Contact Input 89
BDC8 ...Repeated for Contact Input 90
BDD0 ...Repeated for Contact Input 91
BDD8 ...Repeated for Contact Input 92
BDE0 ...Repeated for Contact Input 93
BDE8 ...Repeated for Contact Input 94
BDF0 ...Repeated for Contact Input 95
BDF8 ...Repeated for Contact Input 96
Contact Input Thresholds (Read/Write Setting)
BE00 Contact Input n Threshold, n = 1 to 48 (48 items) 0 to 3 --- 1 F128 1 (33 Vdc)
Virtual Inputs (Read/Write Setting) (64 modules)
BE30 Virtual Input 1 Function 0 to 1 --- 1 F102 0 (Disabled)
BE31 Virtual Input 1 Name --- --- --- F205 “Virt Ip 1“
BE37 Virtual Input 1 Programmed Type 0 to 1 --- 1 F127 0 (Latched)
BE38 Virtual Input 1 Events 0 to 1 --- 1 F102 0 (Disabled)
BE39 Reserved (3 items) --- --- --- F001 0
BE3C ...Repeated for Virtual Input 2
BE48 ...Repeated for Virtual Input 3
BEA8 ...Repeated for Virtual Input 11
BEB4 ...Repeated for Virtual Input 12


BEC0 ...Repeated for Virtual Input 13
BECC ...Repeated for Virtual Input 14
BED8 ...Repeated for Virtual Input 15
BEE4 ...Repeated for Virtual Input 16
BEF0 ...Repeated for Virtual Input 17
BEFC ...Repeated for Virtual Input 18
BF08 ...Repeated for Virtual Input 19
BF2C ...Repeated for Virtual Input 22
B
BFA4 ...Repeated for Virtual Input 32
BFB0 ...Repeated for Virtual Input 33
BFBC ...Repeated for Virtual Input 34
BFC8 ...Repeated for Virtual Input 35
BFD4 ...Repeated for Virtual Input 36
BFE0 ...Repeated for Virtual Input 37
BFEC ...Repeated for Virtual Input 38
BFF8 ...Repeated for Virtual Input 39
C004 ...Repeated for Virtual Input 40
C01C ...Repeated for Virtual Input 42
C0A0 ...Repeated for Virtual Input 53
C0AC ...Repeated for Virtual Input 54
C0B8 ...Repeated for Virtual Input 55
C0C4 ...Repeated for Virtual Input 56
C0D0 ...Repeated for Virtual Input 57
C0DC ...Repeated for Virtual Input 58
C0E8 ...Repeated for Virtual Input 59
C0F4 ...Repeated for Virtual Input 60
Virtual Outputs (Read/Write Setting) (96 modules)
C130 Virtual Output 1 Name --- --- --- F205 “Virt Op 1 “


C136 Virtual Output 1 Events 0 to 1 --- 1 F102 0 (Disabled)
C137 Reserved --- --- --- F001 0
C138 ...Repeated for Virtual Output 2
C180 ...Repeated for Virtual Output 11 B
C1A0 ...Repeated for Virtual Output 15
C1B0 ...Repeated for Virtual Output 17
C1C0 ...Repeated for Virtual Output 19
C1D0 ...Repeated for Virtual Output 21
C1E0 ...Repeated for Virtual Output 23
C1F0 ...Repeated for Virtual Output 25


B
Mandatory (Read/Write Setting)
C430 Test Mode Function 0 to 2 --- 1 F245 0 (Disabled)
C431 Force VFD and LED 0 to 1 --- 1 F126 0 (No)
C432 Test Mode Initiate 0 to 4294967295 --- 1 F300 1
Clear commands (read/write)
C434 Clear All Relay Records Command 0 to 1 --- 1 F126 0 (No)
Mandatory (Read Only)
C435 DSP Advanced Diagnostics Active 0 to 1 -- 1 F126 0 (No)
C436 Synchrophasor Feature Active 0 to 1 -- 1 F126 0 (No)
Mandatory (Read/Write Command)
C434 Relay Reboot Command 0 to 1 --- 1 F126 0 (No)


C438 Save Volatile Data 0 to 1 --- 1 F126 0 (No)
Clear Records (Read/Write Setting)
C450 Clear Fault Reports operand 0 to 4294967295 --- 1 F300 0
C454 Clear Event Records operand 0 to 4294967295 --- 1 F300 0
C456 Clear Oscillography operand 0 to 4294967295 --- 1 F300 0
C458 Clear Data Logger operand 0 to 4294967295 --- 1 F300 0
C45A Clear Breaker 1 Arcing Current operand 0 to 4294967295 --- 1 F300 0
C45C Clear Breaker 2 Arcing Current operand 0 to 4294967295 --- 1 F300 0
C45E Clear Breaker 3 Arcing Current operand 0 to 4294967295 --- 1 F300 0
C460 Clear Breaker 4 Arcing Current operand 0 to 4294967295 --- 1 F300 0
C468 Clear Energy operand 0 to 4294967295 --- 1 F300 0
C46C Clear Unauthorized Access operand 0 to 4294967295 --- 1 F300 0 B
C470 Clear Platform Direct Input/Output Statistics operand 0 to 4294967295 --- 1 F300 0
C472 Reserved (13 items) --- --- --- F001 0
Platform Direct Outputs (Read/Write Setting) (96 modules)
C600 Direct Output 1 Operand 0 to 4294967295 --- 1 F300 0
C602 Direct Output 1 Events 0 to 1 --- 1 F102 0 (Disabled)
C603 ...Repeated for Direct Output 2
C60C ...Repeated for Direct Output 5
C60F ...Repeated for Direct Output 6
C61B ...Repeated for Direct Output 10
C61E ...Repeated for Direct Output 11
C62A ...Repeated for Direct Output 15
C62D ...Repeated for Direct Output 16
C63C ...Repeated for Direct Output 21
C63F ...Repeated for Direct Output 22
C64B ...Repeated for Direct Output 26
C65A ...Repeated for Direct Output 31
Reset (Read/Write Setting)
C750 FlexLogic operand which initiates a reset 0 to 4294967295 --- 1 F300 0
Control Pushbuttons (Read/Write Setting) (7 modules)
C760 Control Pushbutton 1 Function 0 to 1 --- 1 F102 0 (Disabled)
C761 Control Pushbutton 1 Events 0 to 1 --- 1 F102 0 (Disabled)
C762 ...Repeated for Control Pushbutton 2


C76A ...Repeated for Control Pushbutton 6
C76C ...Repeated for Control Pushbutton 7
Force Contact Inputs/Outputs (Read/Write Settings)
C7A0 Force Contact Input x State (96 items) 0 to 2 --- 1 F144 0 (Disabled)
C800 Force Contact Output x State (64 items) 0 to 3 --- 1 F131 0 (Disabled)
Direct Inputs/Outputs (Read/Write Setting)
C880 Direct Device ID 1 to 16 --- 1 F001 1
B
C881 Direct I/O Channel 1 Ring Configuration Function 0 to 1 --- 1 F126 0 (No)
C882 Platform Direct I/O Data Rate 64 to 128 kbps 64 F001 64
C883 Direct I/O Channel 2 Ring Configuration Function 0 to 1 --- 1 F126 0 (No)
C884 Platform Direct I/O Crossover Function 0 to 1 --- 1 F102 0 (Disabled)
Direct input/output commands (Read/Write Command)
C888 Direct input/output clear counters command 0 to 1 --- 1 F126 0 (No)
Direct inputs (Read/Write Setting) (96 modules)
C890 Direct Input 1 Device Number 0 to 16 --- 1 F001 0
C891 Direct Input 1 Number 0 to 96 --- 1 F001 0
C892 Direct Input 1 Default State 0 to 3 --- 1 F086 0 (Off)
C893 Direct Input 1 Events 0 to 1 --- 1 F102 0 (Disabled)
C894 ...Repeated for Direct Input 2
C89C ...Repeated for Direct Input 4
C8A0 ...Repeated for Direct Input 5
C8AC ...Repeated for Direct Input 8
C8B0 ...Repeated for Direct Input 9
C8BC ...Repeated for Direct Input 12
C8C0 ...Repeated for Direct Input 13
C8CC ...Repeated for Direct Input 16
C8D0 ...Repeated for Direct Input 17
C8DC ...Repeated for Direct Input 20
C8E0 ...Repeated for Direct Input 21
C8EC ...Repeated for Direct Input 24
C8F0 ...Repeated for Direct Input 25
C8FC ...Repeated for Direct Input 28
C90C ...Repeated for Direct Input 32
Direct Input/Output Alarms (Read/Write Setting)
CAD0 Direct Input/Output Channel 1 CRC Alarm Function 0 to 1 --- 1 F102 0 (Disabled)


CAD1 Direct I/O Channel 1 CRC Alarm Message Count 100 to 10000 --- 1 F001 600
CAD2 Direct Input/Output Channel 1 CRC Alarm Threshold 1 to 1000 --- 1 F001 10
CAD3 Direct Input/Output Channel 1 CRC Alarm Events 0 to 1 --- 1 F102 0 (Disabled)
CAD4 Reserved (4 items) 1 to 1000 --- 1 F001 10
CAD8 Direct Input/Output Channel 2 CRC Alarm Function 0 to 1 --- 1 F102 0 (Disabled)
CAD9 Direct I/O Channel 2 CRC Alarm Message Count 100 to 10000 --- 1 F001 600
CADA Direct Input/Output Channel 2 CRC Alarm Threshold 1 to 1000 --- 1 F001 10
CADB Direct Input/Output Channel 2 CRC Alarm Events 0 to 1 --- 1 F102 0 (Disabled)
CADC Reserved (4 items) 1 to 1000 --- 1 F001 10
CAE0 Direct I/O Ch 1 Unreturned Messages Alarm Function 0 to 1 --- 1 F102 0 (Disabled)
CAE1 Direct I/O Ch 1 Unreturned Messages Alarm Msg Count 100 to 10000 --- 1 F001 600
CAE2 Direct I/O Ch 1 Unreturned Messages Alarm Threshold 1 to 1000 --- 1 F001 10 B
CAE3 Direct I/O Ch 1 Unreturned Messages Alarm Events 0 to 1 --- 1 F102 0 (Disabled)
CAE4 Reserved (4 items) 1 to 1000 --- 1 F001 10
CAE8 Direct IO Ch 2 Unreturned Messages Alarm Function 0 to 1 --- 1 F102 0 (Disabled)
CAE9 Direct I/O Ch 2 Unreturned Messages Alarm Msg Count 100 to 10000 --- 1 F001 600
CAEA Direct I/O Ch 2 Unreturned Messages Alarm Threshold 1 to 1000 --- 1 F001 10
CAEB Direct I/O Channel 2 Unreturned Messages Alarm Events 0 to 1 --- 1 F102 0 (Disabled)
CAEC Reserved (4 items) --- --- 1 F001 10
Remote Devices (Read/Write Setting) (32 modules)
CB00 Remote Device 1 GSSE/GOOSE Application ID --- --- --- F209 “Remote Device
1“
CB21 Remote Device 1 GOOSE Ethernet APPID 0 to 16383 --- 1 F001 0
CB22 Remote Device 1 GOOSE Dataset 0 to 16 --- 1 F184 0 (Fixed)
CB24 Undefined 0 to 3 --- 1 F626 0 (None)
CB25 ...Repeated for Device 2
CB4A ...Repeated for Device 3
CB6F ...Repeated for Device 4
CB94 ...Repeated for Device 5
CBB9 ...Repeated for Device 6
CBDE ...Repeated for Device 7
CC03 ...Repeated for Device 8
CC4D ...Repeated for Device 10
CCBC ...Repeated for Device 13
CCE1 ...Repeated for Device 14
CD06 ...Repeated for Device 15
CD2B ...Repeated for Device 16
CD9A ...Repeated for Device 19
CDBF ...Repeated for Device 20
CDE4 ...Repeated for Device 21
CE09 ...Repeated for Device 22
CE2E ...Repeated for Device 23
CE9D ...Repeated for Device 26
CEC2 ...Repeated for Device 27
CEE7 ...Repeated for Device 28
CF0C ...Repeated for Device 29
CF31 ...Repeated for Device 30


CF56 ...Repeated for Device 31
CF7B ...Repeated for Device 32
Remote Inputs (Read/Write Setting) (64 modules)
CFA0 Remote Input 1 Device 1 to 16 --- 1 F001 1
CFA1 Remote Input 1 Item 0 to 64 --- 1 F156 0 (None)
CFA2 Remote Input 1 Default State 0 to 3 --- 1 F086 0 (Off)
CFA3 Remote Input 1 Events 0 to 1 --- 1 F102 0 (Disabled)
CFA4 Remote Input 1 Name 1 to 64 --- 1 F205 “Rem Ip 1”
CFAA ...Repeated for Remote Input 2
CFB4 ...Repeated for Remote Input 3
B
CFBE ...Repeated for Remote Input 4
CFC8 ...Repeated for Remote Input 5
CFD2 ...Repeated for Remote Input 6
CFDC ...Repeated for Remote Input 7
CFE6 ...Repeated for Remote Input 8
CFF0 ...Repeated for Remote Input 9
CFFA ...Repeated for Remote Input 10
D004 ...Repeated for Remote Input 11
D00E ...Repeated for Remote Input 12
D02C ...Repeated for Remote Input 15
D04A ...Repeated for Remote Input 18
D0A4 ...Repeated for Remote Input 27
D0AE ...Repeated for Remote Input 28
D0B8 ...Repeated for Remote Input 29
D0C2 ...Repeated for Remote Input 30
D0CC ...Repeated for Remote Input 31
D0D6 ...Repeated for Remote Input 32
D0E0 ...Repeated for Remote Input 33
D0EA ...Repeated for Remote Input 34
D0F4 ...Repeated for Remote Input 35
D0FE ...Repeated for Remote Input 36


D1A8 ...Repeated for Remote Input 53
D1B2 ...Repeated for Remote Input 54
D1BC ...Repeated for Remote Input 55
D1C6 ...Repeated for Remote Input 56
D1D0 ...Repeated for Remote Input 57
D1DA ...Repeated for Remote Input 58
D1E4 ...Repeated for Remote Input 59 B
D1EE ...Repeated for Remote Input 60
D1F8 ...Repeated for Remote Input 61
Remote Output DNA Pairs (Read/Write Setting) (32 modules)
D220 Remote Output DNA 1 Operand 0 to 4294967295 --- 1 F300 0
D221 Remote Output DNA 1 Events 0 to 1 --- 1 F102 0 (Disabled)
D222 Reserved (2 items) 0 to 1 --- 1 F001 0
D224 ...Repeated for Remote Output 2
D22C ...Repeated for Remote Output 4
Remote Output UserSt Pairs (Read/Write Setting) (32 modules)
D2A0 Remote Output UserSt 1 Operand 0 to 4294967295 --- 1 F300 0


D2A1 Remote Output UserSt 1 Events 0 to 1 --- 1 F102 0 (Disabled)
D2A2 Reserved (2 items) 0 to 1 --- 1 F001 0
D2A4 ...Repeated for Remote Output 2
D2A8 ...Repeated for Remote Output 3
D2AC ...Repeated for Remote Output 4
D2B0 ...Repeated for Remote Output 5
D2BC ...Repeated for Remote Output 8
D2C0 ...Repeated for Remote Output 9
B
D2CC ...Repeated for Remote Output 12
D2D0 ...Repeated for Remote Output 13
D2DC ...Repeated for Remote Output 16
D2E0 ...Repeated for Remote Output 17
D2EC ...Repeated for Remote Output 20
D2F0 ...Repeated for Remote Output 21
D2FC ...Repeated for Remote Output 24
IEC 61850 GGIO2 Control Configuration (Read/Write Setting) (64 modules)
D320 IEC 61850 GGIO2.CF.SPCSO1.ctlModel Value 0 to 2 --- 1 F001 2
D32A IEC 61850 GGIO2.CF.SPCSO11.ctlModel Value 0 to 2 --- 1 F001 2
D32B IEC 61850 GGIO2.CF.SPCSO12.ctlModel Value 0 to 2 --- 1 F001 2
D32C IEC 61850 GGIO2.CF.SPCSO13.ctlModel Value 0 to 2 --- 1 F001 2
D32D IEC 61850 GGIO2.CF.SPCSO14.ctlModel Value 0 to 2 --- 1 F001 2
D32E IEC 61850 GGIO2.CF.SPCSO15.ctlModel Value 0 to 2 --- 1 F001 2
D32F IEC 61850 GGIO2.CF.SPCSO16.ctlModel Value 0 to 2 --- 1 F001 2


D33F IEC 61850 GGIO2.CF.SPCSO32.ctlModel Value 0 to 2 --- 1 F001 2 B
Remote Device Status (Read Only) (32 modules)
D380 Remote Device 1 StNum 0 to 4294967295 --- 1 F003 0
D382 Remote Device 1 SqNum 0 to 4294967295 --- 1 F003 0
D384 ...Repeated for Remote Device 2
D38C ...Repeated for Remote Device 4
D39C ...Repeated for Remote Device 8


D3A0 ...Repeated for Remote Device 9
D3AC ...Repeated for Remote Device 12
D3B0 ...Repeated for Remote Device 13
D3BC ...Repeated for Remote Device 16
D3C0 ...Repeated for Remote Device 17
B
D3CC ...Repeated for Remote Device 20
D3D0 ...Repeated for Remote Device 21
D3DC ...Repeated for Remote Device 24
D3E0 ...Repeated for Remote Device 25
D3EC ...Repeated for Remote Device 28
D3F0 ...Repeated for Remote Device 29
D3FC ...Repeated for Remote Device 32
Phasor Measurement Unit Basic Configuration (Read/Write Setting) (4 modules)
D400 PMU x Function 0 to 1 --- 1 F102 0 (Disabled)
D401 PMU x LDInst --- --- 1 F214 "PMUx \040"
D422 PMU x IDcode 1 to 65534 --- 1 F001 1
D423 PMU x STN --- --- --- F203 "GE-UR-PMU"
D42B PMU x Source 0 to 5 --- 1 F167 0 (SRC 1)
D42C PMU x Class 0 to 2 --- 1 F549 1 (Class M)
D42D PMU x Format 0 to 1 --- 1 F547 0 (Integer)
D42E PMU x Style 0 to 1 --- 1 F546 0 (Polar)
D42F PMU x Rate 0 to 13 --- 1 F544 4 (10/sec)
D430 PMU x PHS-x (14 items) 0 to 14 --- 1 F543 1 (Va)
D43E PMU x PHS-x Name (14 items) --- --- --- F203 "GE-UR-PMU-
PHS 1 "
D4AE PMU x A-CH-x (16 items) 0 to 65535 --- 1 F600 0
D4BE PMU x A-CH-x (16 items) --- --- --- F203 "AnalogChannel 1
"
D53E PMU x D-CH-x (16 items) 0 to 4294967295 --- 1 F300 0
D55E PMU x D-CH-x Name (16 items) --- --- --- F203 "Dig Channel 1 "
D5DE PMU x D-CH-x Normal State (16 items) 0 to 1 --- 1 F108 0 (Off)
D5EE PMU x Reserved (16 items) 0 to 1 --- 1 F001 0
Contact Outputs (Read/Write Setting) (64 modules)
DC90 Contact Output 1 Name --- --- --- F205 “Cont Op 1"
DC96 Contact Output 1 Operation 0 to 4294967295 --- 1 F300 0
DC98 Contact Output 1 Seal In 0 to 4294967295 --- 1 F300 0
DC9A Latching Output 1 Reset 0 to 4294967295 --- 1 F300 0
DC9C Contact Output 1 Events 0 to 1 --- 1 F102 1 (Enabled)
DC9D Latching Output 1 Type 0 to 1 --- 1 F090 0 (Operate-
dominant)
DC9E Reserved --- --- --- F001 0
DC9F ...Repeated for Contact Output 2
DCAE ...Repeated for Contact Output 3


DCBD ...Repeated for Contact Output 4
DCCC ...Repeated for Contact Output 5
DCDB ...Repeated for Contact Output 6
DCEA ...Repeated for Contact Output 7
DCF9 ...Repeated for Contact Output 8
DD08 ...Repeated for Contact Output 9
DD62 ...Repeated for Contact Output 15 B
DD8F ...Repeated for Contact Output 18
DD9E ...Repeated for Contact Output 19
DDAD ...Repeated for Contact Output 20
DDBC ...Repeated for Contact Output 21
DDCB ...Repeated for Contact Output 22
DDDA ...Repeated for Contact Output 23
DDE9 ...Repeated for Contact Output 24
DDF8 ...Repeated for Contact Output 25
DE07 ...Repeated for Contact Output 26
DE7F ...Repeated for Contact Output 34
DE8E ...Repeated for Contact Output 35
DE9D ...Repeated for Contact Output 36
DEAC ...Repeated for Contact Output 37
DEBB ...Repeated for Contact Output 38
DECA ...Repeated for Contact Output 39
DED9 ...Repeated for Contact Output 40
DEE8 ...Repeated for Contact Output 41
DEF7 ...Repeated for Contact Output 42
DF06 ...Repeated for Contact Output 43
DF6F ...Repeated for Contact Output 50
DF7E ...Repeated for Contact Output 51
DF8D ...Repeated for Contact Output 52
DF9C ...Repeated for Contact Output 53
DFAB ...Repeated for Contact Output 54
DFBA ...Repeated for Contact Output 55
DFC9 ...Repeated for Contact Output 56
DFD8 ...Repeated for Contact Output 57


DFE7 ...Repeated for Contact Output 58
DFF6 ...Repeated for Contact Output 59
E005 ...Repeated for Contact Output 60
dcmA Inputs (Read/Write Setting) (24 modules)
E050 dcmA Inputs 1 Function 0 to 1 --- 1 F102 0 (Disabled)
E051 dcmA Inputs 1 ID --- --- --- F205 “DCMA I 1"
B
E057 Reserved 1 (4 items) 0 to 65535 --- 1 F001 0
E05B dcmA Inputs 1 Units --- --- --- F206 “mA”
E05E dcmA Inputs 1 Range 0 to 6 --- 1 F173 6 (4 to 20 mA)
E05F dcmA Inputs 1 Minimum Value -9999.999 to 9999.999 --- 0.001 F004 4000
E061 dcmA Inputs 1 Maximum Value -9999.999 to 9999.999 --- 0.001 F004 20000
E063 ...Repeated for dcmA Inputs 2
E09C ...Repeated for dcmA Inputs 5
E0AF ...Repeated for dcmA Inputs 6
E0C2 ...Repeated for dcmA Inputs 7
E0D5 ...Repeated for dcmA Inputs 8
E0E8 ...Repeated for dcmA Inputs 9
E0FB ...Repeated for dcmA Inputs 10
E10E ...Repeated for dcmA Inputs 11
E15A ...Repeated for dcmA Inputs 15
E16D ...Repeated for dcmA Inputs 16
E1A6 ...Repeated for dcmA Inputs 19
E1B9 ...Repeated for dcmA Inputs 20
E1CC ...Repeated for dcmA Inputs 21
E1DF ...Repeated for dcmA Inputs 22
E1F2 ...Repeated for dcmA Inputs 23
Phasor Measurement Unit Aggregator (Read/Write Setting) (4 modules)
E220 PMU Aggregator 1 Name --- --- 1 F209 "MSVID 1 "
E241 Aggregator 1 IDcode 1 to 65534 --- 1 F001 1
E242 Aggregator 1 Protocol 0 to 2 --- 1 F001 0 (NONE)
E243 Aggregator 1 TCP Port 0 to 65534 --- 1 F001 4712
E244 Aggregator 1 UDP Port 0 to 65534 --- 1 F001 4713
E245 PMU Aggregator 1 90-5 UDP Port 0 to 65534 --- 1 F001 102
E246 PMU Aggregator 1 PDC Network Control 0 to 1 --- 1 F102 0 (Disabled)
E247 Aggregator 1 Include PMU1 0 to 1 --- 1 F126 0 (No)
E24A Aggregator 1 Include PMU4 0 to 1 --- 1 F126 0 (No)
E24B PMU Aggregator 1 ASDUS 1 to 4 --- 1 F001 1
E24C PMU Aggregator 1 Port 1 to 3 --- 1 F001 1
E24D PMU Aggregator 1 Reserved (3 items) 1 to 3 --- 1 F001 0
E250 ...Repeated for PMU Aggregator 2


E280 ...Repeated for PMU Aggregator 3
E2B0 ...Repeated for PMU Aggregator 4
Phasor Measurement Unit Recording Command (Read/Write Command)
E4D4 PMU 1 Recording Clear Command 0 to 1 --- 1 F126 0 (No)
E4D5 PMU 1 Recording Force Trigger 0 to 1 --- 1 F126 0 (No)
Phasor Measurement Unit Recording (Read/Write Setting)
E4DC PMU 1 Record Function 0 to 1 --- 1 F102 0 (Disabled)
E4DD PMU 1 No Of Timed Records 2 to 128 --- 1 F001 3
E4DE PMU 1 Trigger Mode 0 to 1 --- 1 F542 0 (Auto
Overwrite)
E4DF PMU 1 Timed Trigger Position 1 to 50 % 1 F001 10
Phasor Measurement Unit Control Block (Read/Write Setting) (4 modules)
E650 PMU Aggregator 1 Control Block SvEna 0 to 4294967295 --- 1 F300 0
B
E652 PMU Aggregator 1 Control Block Client Control 0 to 4294967295 --- 1 F300 0
E654 PMU Aggregator 1 CB SvEna Default 0 to 4294967295 --- 1 F300 0
E656 PMU Aggregator 1 Control Block ConfRev 1 to 4294967295 --- 1 F003 1
E658 PMU Aggregator 1 Control Block Priority 0 to 7 --- 1 F001 4
E659 PMU Aggregator 1 Control Block IPClass 0 to 1 --- 1 F563 1 (Expedited
Forwarding)
E65A PMU Aggregator 1 Control Block VID 0 to 4095 --- 1 F001 0
E65B PMU Aggregator 1 Control Block APPID 0 to 16383 --- 1 F001 0
E65C PMU Aggregator 1 Control Block IP Address 0 to 4294967295 --- 1 F003 0
E65E PMU Aggregator 1 Control Block Security 0 to 2 --- 1 F001 0
E65F ...Repeated for PMU Aggregator 2
E66E ...Repeated for PMU Aggregator 3
E67D ...Repeated for PMU Aggregator 4
DNP/IEC Points (Read/Write Setting)
E700 DNP/IEC 60870-5-104 Binary Input Points (256 items) 0 to 4294967295 --- 1 F300 0
E900 DNP/IEC 60870-5-104 Analog Input Points (256 items) 0 to 65535 --- 1 F300 0
Synchrocheck (Read/Write Setting) (4 modules)
EC00 Synchrocheck 1 Function 0 to 1 --- 1 F102 0 (Disabled)
EC01 Synchrocheck 1 V1 Source 0 to 5 --- 1 F167 0 (SRC 1)
EC02 Synchrocheck 1 V2 Source 0 to 5 --- 1 F167 1 (SRC 2)
EC03 Synchrocheck 1 Maximum Voltage Difference 0 to 400000 V 1 F060 10000
EC05 Synchrocheck 1 Maximum Angle Difference 0 to 100 degrees 1 F001 30
EC06 Synchrocheck 1 Maximum Frequency Difference 0 to 2 Hz 0.01 F001 100
EC07 Synchrocheck 1 Dead Source Select 0 to 5 --- 1 F176 1 (LV1 and DV2)
EC08 Synchrocheck 1 Dead V1 Maximum Voltage 0 to 1.25 pu 0.01 F001 30
EC09 Synchrocheck 1 Dead V2 Maximum Voltage 0 to 1.25 pu 0.01 F001 30
EC0A Synchrocheck 1 Live V1 Minimum Voltage 0 to 1.25 pu 0.01 F001 70
EC0B Synchrocheck 1 Live V2 Minimum Voltage 0 to 1.25 pu 0.01 F001 70
EC0C Synchrocheck 1 Target 0 to 2 --- 1 F109 0 (Self-reset)
EC0D Synchrocheck 1 Events 0 to 1 --- 1 F102 0 (Disabled)
EC0E Synchrocheck 1 Block 0 to 4294967295 --- 1 F300 0
EC10 Synchrocheck 1 Frequency Hysteresis 0 to 0.1 Hz 0.01 F001 6
EC11 ...Repeated for Synchrocheck 2
Phasor Measurement Unit Frequency Trigger (Read/Write Setting) (4 modules)
ECCC PMU 1 Frequency Trigger Function 0 to 1 --- 1 F102 0 (Disabled)
ECCD PMU 1 Frequency Trigger Low Frequency 20 to 70 Hz 0.01 F001 4900
ECCE PMU 1 Frequency Trigger High Frequency 20 to 70 Hz 0.01 F001 6100
ECCF PMU 1 Frequency Trigger Pickup Time 0 to 600 s 0.01 F001 10
ECD0 PMU 1 Frequency Trigger Dropout Time 0 to 600 s 0.01 F001 100
ECD1 PMU 1 Frequency Trigger Block (3 items) 0 to 4294967295 --- 1 F300 0


ECD7 PMU 1 Frequency Trigger Target 0 to 2 --- 1 F109 0 (Self-reset)
ECD8 PMU 1 Frequency Trigger Events 0 to 1 --- 1 F102 0 (Disabled)
Setting file template values (read only)
ED00 FlexLogic displays active 0 to 1 --- 1 F102 1 (Enabled)
ED01 Undefined --- --- --- F205 (none)
ED07 Last settings change date 0 to 4294967295 --- 1 F050 0
ED09 Template bitmask (750 items) 0 to 65535 --- 1 F001 0
Phasor Measurement Unit Records (Read Only)
EFFF PMU Recording Number of Triggers 0 to 65535 samples 1 F001 0

B.4.2 DATA FORMATS
F001 F040
UR_UINT16 UNSIGNED 16 BIT INTEGER UR_UINT48 48-BIT UNSIGNED INTEGER
F002 F050
UR_SINT16 SIGNED 16 BIT INTEGER UR_UINT32 TIME and DATE (UNSIGNED 32 BIT INTEGER)
Gives the current time in seconds elapsed since 00:00:00 January
1, 1970.
F003
UR_UINT32 UNSIGNED 32 BIT INTEGER (2 registers)
High order word is stored in the first register.
Low order word is stored in the second register.
F051
UR_UINT32 DATE in SR format (alternate format for F050) B
First 16 bits are Month/Day (MM/DD/xxxx). Month: 1=January,
2=February,...,12=December; Day: 1 to 31 in steps of 1
F004
Last 16 bits are Year (xx/xx/YYYY): 1970 to 2106 in steps of 1
UR_SINT32 SIGNED 32 BIT INTEGER (2 registers)
High order word is stored in the first register/
Low order word is stored in the second register. F052
UR_UINT32 TIME in SR format (alternate format for F050)
First 16 bits are Hours/Minutes (HH:MM:xx.xxx).
F005
Hours: 0=12am, 1=1am,...,12=12pm,...23=11pm;
UR_UINT8 UNSIGNED 8 BIT INTEGER
Minutes: 0 to 59 in steps of 1
Last 16 bits are Seconds (xx:xx:.SS.SSS): 0=00.000s,
F006 1=00.001,...,59999=59.999s)
UR_SINT8 SIGNED 8 BIT INTEGER
F060
F011 FLOATING_POINT IEEE FLOATING POINT (32 bits)
UR_UINT16 FLEXCURVE DATA (120 points)
A FlexCurve is an array of 120 consecutive data points (x, y) which
F070
are interpolated to generate a smooth curve. The y-axis is the user
HEX2 2 BYTES - 4 ASCII DIGITS
defined trip or operation time setting; the x-axis is the pickup ratio
and is pre-defined. Refer to format F119 for a listing of the pickup
ratios; the enumeration value for the pickup ratio indicates the off-
F071
set into the FlexCurve base address where the corresponding time HEX4 4 BYTES - 8 ASCII DIGITS
value is stored.
F072
F012
DISPLAY_SCALE DISPLAY SCALING
(unsigned 16-bit integer)
MSB indicates the SI units as a power of ten. LSB indicates the F073
number of decimal points to display. HEX8 8 BYTES - 16 ASCII DIGITS
Example: Current values are stored as 32 bit numbers with three
decimal places and base units in Amps. If the retrieved value is
F074
12345.678 A and the display scale equals 0x0302 then the dis-
played value on the unit is 12.35 kA.
F081
F013
ENUMERATION: AUTORECLOSE 1P/3P BKR FAIL OPTION
POWER_FACTOR (SIGNED 16 BIT INTEGER)
0 = Continue, 1 = Lockout
Positive values indicate lagging power factor; negative values
indicate leading.

F082 F103
ENUMERATION: AUTORECLOSE SINGLE-PHASE / ENUMERATION: CURVE SHAPES
THREE-PHASE BREAKER SEQUENCE
bitmask curve shape bitmask curve shape
0 = 1, 1 = 2, 2 = 1 & 2, 3 = 1 – 2, 4 = 2 – 1
0 IEEE Mod Inv 9 IAC Inverse
1 IEEE Very Inv 10 IAC Short Inv
F083 2 IEEE Ext Inv 11 I2t
ENUMERATION: SELECTOR MODES 3 IEC Curve A 12 Definite Time
0 = Time-Out, 1 = Acknowledge 4 IEC Curve B 13 FlexCurve A
5 IEC Curve C 14 FlexCurve B
6 IEC Short Inv 15 FlexCurve C
F084
7 IAC Ext Inv 16 FlexCurve D
ENUMERATION: SELECTOR POWER UP
B 0 = Restore, 1 = Synchronize, 2 = Sync/Restore
8 IAC Very Inv
F104
F085 ENUMERATION: RESET TYPE
ENUMERATION: POWER SWING SHAPE
0 = Instantaneous, 1 = Timed, 2 = Linear
0 = Mho Shape, 1 = Quad Shape
F105
F086 ENUMERATION: LOGIC INPUT
ENUMERATION: DIGITAL INPUT DEFAULT STATE
0 = Disabled, 1 = Input 1, 2 = Input 2
0 = Off, 1 = On, 2= Latest/Off, 3 = Latest/On
F106
F090 ENUMERATION: PHASE ROTATION
ENUMERATION: LATCHING OUTPUT TYPE
0 = ABC, 1 = ACB
0 = Operate-dominant, 1 = Reset-dominant
F108
F100 ENUMERATION: OFF/ON
ENUMERATION: VT CONNECTION TYPE
0 = Off, 1 = On
0 = Wye; 1 = Delta
F109
F101 ENUMERATION: CONTACT OUTPUT OPERATION
ENUMERATION: MESSAGE DISPLAY INTENSITY
0 = Self-reset, 1 = Latched, 2 = Disabled
0 = 25%, 1 = 50%, 2 = 75%, 3 = 100%
F110
F102 ENUMERATION: CONTACT OUTPUT LED CONTROL
ENUMERATION: DISABLED/ENABLED
0 = Trip, 1 = Alarm, 2 = None
0 = Disabled; 1 = Enabled
F111
ENUMERATION: UNDERVOLTAGE CURVE SHAPES
0 = Definite Time, 1 = Inverse Time

F112 F119
ENUMERATION: RS485 BAUD RATES ENUMERATION: FLEXCURVE PICKUP RATIOS
bitmask value bitmask value bitmask value mask value mask value mask value mask value
0 300 4 9600 8 115200 0 0.00 30 0.88 60 2.90 90 5.90
1 1200 5 19200 9 14400 1 0.05 31 0.90 61 3.00 91 6.00
2 2400 6 38400 10 28800 2 0.10 32 0.91 62 3.10 92 6.50
3 4800 7 57600 11 33600 3 0.15 33 0.92 63 3.20 93 7.00
4 0.20 34 0.93 64 3.30 94 7.50
5 0.25 35 0.94 65 3.40 95 8.00
F113
6 0.30 36 0.95 66 3.50 96 8.50
ENUMERATION: PARITY
7 0.35 37 0.96 67 3.60 97 9.00
0 = None, 1 = Odd, 2 = Even
8
9
0.40
0.45
38
39
0.97
0.98
68
69
3.70
3.80
98
99
9.50
10.00
B
F114 10 0.48 40 1.03 70 3.90 100 10.50
ENUMERATION: IRIG-B SIGNAL TYPE 11 0.50 41 1.05 71 4.00 101 11.00
0 = None, 1 = DC Shift, 2 = Amplitude Modulated 12 0.52 42 1.10 72 4.10 102 11.50

13 0.54 43 1.20 73 4.20 103 12.00
14 0.56 44 1.30 74 4.30 104 12.50
F115 15 0.58 45 1.40 75 4.40 105 13.00
ENUMERATION: BREAKER STATUS
16 0.60 46 1.50 76 4.50 106 13.50
0 = Auxiliary A, 1 = Auxiliary B 17 0.62 47 1.60 77 4.60 107 14.00
18 0.64 48 1.70 78 4.70 108 14.50
19 0.66 49 1.80 79 4.80 109 15.00
F116
ENUMERATION: NEUTRAL OVERVOLTAGE CURVES 20 0.68 50 1.90 80 4.90 110 15.50
21 0.70 51 2.00 81 5.00 111 16.00
0 = Definite Time, 1 = FlexCurve A, 2 = FlexCurve B,
3 = FlexCurve C 22 0.72 52 2.10 82 5.10 112 16.50
23 0.74 53 2.20 83 5.20 113 17.00
24 0.76 54 2.30 84 5.30 114 17.50
F117 25 0.78 55 2.40 85 5.40 115 18.00
ENUMERATION: NUMBER OF OSCILLOGRAPHY RECORDS
26 0.80 56 2.50 86 5.50 116 18.50
0 = 172 cycles, 1 = 336 cycles, 2 = 718 cycles, 3 = 159 cycles 27 0.82 57 2.60 87 5.60 117 19.00
28 0.84 58 2.70 88 5.70 118 19.50
29 0.86 59 2.80 89 5.80 119 20.00
F118
ENUMERATION: OSCILLOGRAPHY MODE
0 = Automatic Overwrite, 1 = Protected F120
ENUMERATION: DISTANCE SHAPE
0 = Mho, 1 = Quad
F122
ENUMERATION: ELEMENT INPUT SIGNAL TYPE
0 = Phasor, 1 = RMS
F123
ENUMERATION: CT SECONDARY
0 = 1 A, 1 = 5 A

bitmask element
F124
225 SRC2 VT Fuse Failure
ENUMERATION: LIST OF ELEMENTS
226 SRC3 VT Fuse Failure
bitmask element 227 SRC4 VT Fuse Failure
0 Phase Instantaneous Overcurrent 1 228 SRC5 VT Fuse Failure
1 Phase Instantaneous Overcurrent 2 229 SRC6 VT Fuse Failure
16 Phase Time Overcurrent 1 232 SRC1 50DD (Disturbance Detection)
17 Phase Time Overcurrent 2 233 SRC2 50DD (Disturbance Detection)
24 Phase Directional Overcurrent 1 234 SRC3 50DD (Disturbance Detection)
25 Phase Directional Overcurrent 2 235 SRC4 50DD (Disturbance Detection)
32 Neutral Instantaneous Overcurrent 1 242 Open Pole Detector
33 Neutral Instantaneous Overcurrent 2 280 Breaker Failure 1
B 48
49
Neutral Time Overcurrent 1
Neutral Time Overcurrent 2
281
282
Breaker Failure 2
Breaker Failure 3
56 Neutral Directional Overcurrent 1 283 Breaker Failure 4
57 Neutral Directional Overcurrent 2 288 Breaker Arcing Current 1
60 Negative Sequence Directional Overcurrent 1 289 Breaker Arcing Current 2
61 Negative Sequence Directional Overcurrent 2 290 Breaker Arcing Current 3
64 Ground Instantaneous Overcurrent 1 291 Breaker Arcing Current 4
65 Ground Instantaneous Overcurrent 2 292 Breaker Arcing Current 5
80 Ground Time Overcurrent 1 293 Breaker Arcing Current 6
81 Ground Time Overcurrent 2 294 Breaker 1 Flashover
96 Negative Sequence Instantaneous Overcurrent 1 295 Breaker 2 Flashover
97 Negative Sequence Instantaneous Overcurrent 2 311 Phasor measurement unit one-shot
101 Opposite Phase Rotation 312 Synchrocheck 1
112 Negative Sequence Time Overcurrent 1 313 Synchrocheck 2
113 Negative Sequence Time Overcurrent 2 336 Setting Group
120 Negative Sequence Overvoltage 337 Reset
121 Wattmetric Zero-Sequence Directional 1 344 Overfrequency 1
122 Wattmetric Zero-Sequence Directional 2 345 Overfrequency 2
140 Auxiliary Undervoltage 1 346 Overfrequency 3
144 Phase Undervoltage 1 347 Overfrequency 4
145 Phase Undervoltage 2 352 Underfrequency 1
148 Auxiliary Overvoltage 1 353 Underfrequency 2
152 Phase Overvoltage 1 354 Underfrequency 3
154 Compensated Overvoltage 1 355 Underfrequency 4
156 Neutral Overvoltage 1 356 Underfrequency 5
160 Phase Distance Zone 1 357 Underfrequency 6
161 Phase Distance Zone 2 360 Trip Output
162 Phase Distance Zone 3 362 Phase Selector
163 Phase Distance Zone 4 363 Open Pole Detector
164 Phase Distance Zone 5 365 Directional Comparison Unblocking Scheme
168 Line Pickup 366 DUTT Pilot Scheme
172 Ground Distance Zone 1 368 PUTT Pilot Scheme
173 Ground Distance Zone 2 370 POTT Pilot Scheme
174 Ground Distance Zone 3 371 POTT1 Pilot Scheme
175 Ground Distance Zone 4 372 Hybrid POTT Pilot Scheme
176 Ground Distance Zone 5 374 Directional Comparison Blocking Pilot Scheme
180 Load Encroachment 388 Selector 1
190 Power Swing Detect 389 Selector 2
214 Sensitive Directional Power 1 390 Control pushbutton 1
215 Sensitive Directional Power 2 391 Control pushbutton 2
224 SRC1 VT Fuse Failure 392 Control pushbutton 3

393 Control pushbutton 4

bitmask element bitmask element

394 Control pushbutton 5 706 Digital Element 15
400 FlexElement 1 709 Digital Element 18
406 FlexElemen 7 715 Digital Element 24
420
421
Non-volatile Latch 1
Non-volatile Latch 2
717
718
Digital Element 26
Digital Element 27
B
422 Non-volatile Latch 3 719 Digital Element 28
530 Frequency Rate of Change 1 733 Digital Element 42
544 Digital Counter 1 737 Digital Element 46
547 Digital Counter 4 740 Phasor Measurement Unit 1 Frequency
548 Digital Counter 5 746 Phasor Measurement Unit 1 Voltage
549 Digital Counter 6 752 Phasor Measurement Unit 1 Current
550 Digital Counter 7 758 Phasor Measurement Unit 1 Power
551 Digital Counter 8 764 PMU 1 Rate of Change of Frequency
692 Digital Element 1 770 Phasor Measurement Unit 1
693 Digital Element 2 842 Trip Bus 1
699 Digital Element 8 849 RTD Input 1

bitmask element bitmask element

856 RTD Input 8 911 User-Programmable Pushbutton 12
861 RTD Input 13 920 Disconnect switch 1
B 867
868
RTD Input 19
RTD Input 20
926
927
Disconnect switch 7
Disconnect switch 8
877 RTD Input 29 968 Breaker 1
881 RTD Input 33 980 Breaker restrike 1
882 RTD Input 34 981 Breaker restrike 2
883 RTD Input 35 1012 Thermal overload protection 1
884 RTD Input 36 1013 Thermal overload protection 2
885 RTD Input 37 1014 Broken conductor detection 1
886 RTD Input 38 1015 Broken conductor detection 2
887 RTD Input 39 1020 Wattmetric 1
888 RTD Input 40 1021 Wattmetric 2
889 RTD Input 41
890 RTD Input 42
F125
891 RTD Input 43
ENUMERATION: ACCESS LEVEL
892 RTD Input 44
0 = Restricted; 1 = Command, 2 = Setting, 3 = Factory Service
893 RTD Input 45
894 RTD Input 46
895 RTD Input 47 F126
896 RTD Input 48 ENUMERATION: NO/YES CHOICE
900 User-Programmable Pushbutton 1 0 = No, 1 = Yes
901 User-Programmable Pushbutton 2
F127
ENUMERATION: LATCHED OR SELF-RESETTING
905 User-Programmable Pushbutton 6 0 = Latched, 1 = Self-Reset
907 User-Programmable Pushbutton 8 F128
908 User-Programmable Pushbutton 9 ENUMERATION: CONTACT INPUT THRESHOLD
0 = 17 V DC, 1 = 33 V DC, 2 = 84 V DC, 3 = 166 V DC

F129 F141
ENUMERATION: FLEXLOGIC TIMER TYPE ENUMERATION: SELF TEST ERRORS
0 = millisecond, 1 = second, 2 = minute
Bitmask Error
0 Any Self Tests
F130 1 IRIG-B Failure
ENUMERATION: SIMULATION MODE 2 Port 1 Offline
0 = Off. 1 = Pre-Fault, 2 = Fault, 3 = Post-Fault 3 Port 2 Offline

4 Port 3 Offline
5 Port 4 Offline
F131 6 Port 5 Offline
ENUMERATION: FORCED CONTACT OUTPUT STATE
7 Port 6 Offline
0 = Disabled, 1 = Energized, 2 = De-energized, 3 = Freeze 8
9
RRTD Communications Failure
Voltage Monitor
B
10 FlexLogic Error Token
F133
ENUMERATION: PROGRAM STATE 11 Equipment Mismatch
12 Process Bus Failure
0 = Not Programmed, 1 = Programmed
13 Unit Not Programmed
14 System Exception
F134 15 Latching Output Discrepancy
ENUMERATION: PASS/FAIL 17 Maintenance Alert 01
0 = Fail, 1 = OK, 2 = n/a 18 SNTP Failure
19 Maintenance Alert
F135
ENUMERATION: GAIN CALIBRATION
22 Temperature Monitor
0 = 0x1, 1 = 1x16
23 Process Bus Trouble
24 Brick Trouble
F136 25 Field RTD Trouble
ENUMERATION: NUMBER OF OSCILLOGRAPHY RECORDS 26 Field TDR Trouble
0 = 31 x 8 cycles, 1 = 15 x 16 cycles, 2 = 7 x 32 cycles 27 Remote Device Offline
3 = 3 x 64 cycles, 4 = 1 x 128 cycles 28 Direct Device Offline
30 Any Minor Error
F137
31 Any Major Error
ENUMERATION: USER-PROGRAMMABLE PUSHBUTTON
FUNCTION 33 Maintenance Alert
0 = Disabled, 1 = Self-Reset, 2 = Latched
65 IEC 61850 Data Set
66 Aggregator Error
F138 67 Unit Not Calibrated
ENUMERATION: OSCILLOGRAPHY FILE TYPE 68 Settings Save Error
0 = Data File, 1 = Configuration File, 2 = Header File 69 SRAM Data Error
70 Program Memory
71 Watchdog Error
F140
72 Low On Memory
ENUMERATION: CURRENT, SENS CURRENT, VOLTAGE,
DISABLED 73 Prototype Firmware
74 Module Failure 01
0 = Disabled, 1 = Current 46 A, 2 = Voltage 280 V,
3 = Current 4.6 A, 4 = Current 2 A, 5 = Notched 4.6 A, 75 Module Failure 02
6 = Notched 2 A 76 Module Failure 03

Bitmask Error bitmask definition

81 Module Failure 08 13 Led Test Initiated
82 Module Failure 09 14 Flash Programming
83 Incompatible H/W 15 Fault Report Trigger
84 Module Failure 10 16 User Programmable Fault Report Trigger
85 Module Failure 11 17 ---
86 Module Failure 12 18 Reload CT/VT module Settings
87 High ENET Traffic 19 ---
89 Relay Restart 20 Ethernet Port 1 Offline
90 FGM Failure 21 Ethernet Port 2 Offline
B 93
94
FGM Failure
FGM Failure
24
25
Ethernet Port 5 Offline
Ethernet Port 6 Offline
95 FGM Error 26 Test Mode Isolated
96 Maintenance Alert 27 Test Mode Forcible
97 PHY Monitor 28 Test Mode Disabled
98 Storage Media Alarm 29 Temperature Warning On
99 Wrong Transceiver 30 Temperature Warning Off
31 Unauthorized Access
32 System Integrity Recovery
F142
33 System Integrity Recovery 06
ENUMERATION: EVENT RECORDER ACCESS FILE TYPE
34 System Integrity Recovery 07
0 = All Record Data, 1 = Headers Only, 2 = Numeric Event Cause
F147
F143 ENUMERATION: LINE LENGTH UNITS
UR_UINT32: 32 BIT ERROR CODE (F141 specifies bit number)
0 = km, 1 = miles
A bit value of 0 = no error, 1 = error
F148
F144 ENUMERATION: FAULT TYPE
ENUMERATION: FORCED CONTACT INPUT STATE
bitmask fault type bitmask fault type
0 = Disabled, 1 = Open, 2 = Closed
0 NA 6 AC
1 AG 7 ABG
F146 2 BG 8 BCG
ENUMERATION: MISCELLANEOUS EVENT CAUSES 3 CG 9 ACG
4 AB 10 ABC
bitmask definition
5 BC 11 ABCG
0 Events Cleared
1 Oscillography Triggered
2 Date/time Changed
3 Default Settings Loaded
4 Test Mode Forcing On
5 Test Mode Forcing Off
6 Power On
7 Power Off
8 Relay In Service
9 Relay Out Of Service
10 Watchdog Reset
11 Oscillography Clear
12 Reboot Command

F151 F156
ENUMERATION: RTD SELECTION ENUMERATION: REMOTE INPUT BIT PAIRS
bitmask RTD# bitmask RTD# bitmask RTD#
bitmask value bitmask value
0 NONE 17 RTD 17 33 RTD 33
0 NONE 35 UserSt-3
1 RTD 1 18 RTD 18 34 RTD 34
1 DNA-1 36 UserSt-4
2 RTD 2 19 RTD 19 35 RTD 35
2 DNA-2 37 UserSt-5
3 RTD 3 20 RTD 20 36 RTD 36
3 DNA-3 38 UserSt-6
4 RTD 4 21 RTD 21 37 RTD 37
4 DNA-4 39 UserSt-7
5 RTD 5 22 RTD 22 38 RTD 38
5 DNA-5 40 UserSt-8
6 RTD 6 23 RTD 23 39 RTD 39
6 DNA-6 41 UserSt-9
7 RTD 7 24 RTD 24 40 RTD 40
7 DNA-7 42 UserSt-10
B
8 RTD 8 25 RTD 25 41 RTD 41
9 RTD 9 26 RTD 26 42 RTD 42
10 RTD 10 27 RTD 27 43 RTD 43
11 RTD 11 28 RTD 28 44 RTD 44
12 RTD 12 29 RTD 29 45 RTD 45
13 RTD 13 30 RTD 30 46 RTD 46
14 RTD 14 31 RTD 31 47 RTD 47
15 RTD 15 32 RTD 32 48 RTD 48
16 RTD 16
F152
ENUMERATION: SETTING GROUP 19 DNA-19 54 UserSt-22
0 = Active Group, 1 = Group 1, 2 = Group 2, 3 = Group 3
4 = Group 4, 5 = Group 5, 6 = Group 6 21 DNA-21 56 UserSt-24
F153 24 DNA-24 59 UserSt-27
ENUMERATION: DISTANCE TRANSFORMER CONNECTION
bitmask type bitmask type bitmask type 26 DNA-26 61 UserSt-29
0 None 5 Dy9 10 Yd7 27 DNA-27 62 UserSt-30
1 Dy1 6 Dy11 11 Yd9 28 DNA-28 63 UserSt-31
2 Dy3 7 Yd1 12 Yd11 29 DNA-29 64 UserSt-32
3 Dy5 8 Yd3 30 DNA-30 65 Dataset Item 1
4 Dy7 9 Yd5 31 DNA-31 66 Dataset Item 2
32 DNA-32 67 Dataset Item 3
33 UserSt-1  
F154
34 UserSt-2 96 Dataset Item 32
ENUMERATION: DISTANCE DIRECTION
0 = Forward, 1 = Reverse, 2 = Non-Directional
F157
ENUMERATION: BREAKER MODE
F155
ENUMERATION: REMOTE DEVICE STATE 0 = 3-Pole, 1 = 1-Pole
0 = Offline, 1 = Online
F158
ENUMERATION: SCHEME CALIBRATION TEST
0 = Normal, 1 = Symmetry 1, 2 = Symmetry 2, 3 = Delay 1
4 = Delay 2
F159
ENUMERATION: BREAKER AUX CONTACT KEYING
0 = 52a, 1 = 52b, 2 = None

F166 F175
ENUMERATION: AUXILIARY VT CONNECTION TYPE ENUMERATION: PHASE LETTERS
0 = Vn, 1 = Vag, 2 = Vbg, 3 = Vcg, 4 = Vab, 5 = Vbc, 6 = Vca 0 = A, 1 = B, 2 = C
F167 F176
ENUMERATION: SIGNAL SOURCE ENUMERATION: SYNCHROCHECK DEAD SOURCE SELECT
0 = SRC 1, 1 = SRC 2, 2 = SRC 3, 3 = SRC 4,
bitmask synchrocheck dead source
4 = SRC 5, 5 = SRC 6
0 None
1 LV1 and DV2
F168 2 DV1 and LV2
ENUMERATION: INRUSH INHIBIT FUNCTION
B 0 = Disabled, 1 = Adapt. 2nd, 2 = Trad. 2nd
3
4
DV1 or DV2
DV1 Xor DV2
5 DV1 and DV2
F170
ENUMERATION: LOW/HIGH OFFSET and GAIN F177
TRANSDUCER INPUT/OUTPUT SELECTION ENUMERATION: COMMUNICATION PORT
0 = LOW, 1 = HIGH 0 = None, 1 = COM1-RS485 (not applicable to UR firmware 7.00),
2 = COM2-RS485, 3 = Front Panel-RS232, 4 = Network - TCP,
5 = Network - UDP
F171
ENUMERATION: TRANSDUCER CHANNEL INPUT TYPE
0 = dcmA IN, 1 = Ohms IN, 2 = RTD IN, 3 = dcmA OUT, F178
4 = RRTD IN ENUMERATION: DATA LOGGER RATES
0 = 1 sec, 1 = 1 min, 2 = 5 min, 3 = 10 min, 4 = 15 min,
5 = 20 min, 6 = 30 min, 7 = 60 min, 8 = 15 ms, 9 = 30 ms,
F172 10 = 100 ms, 11 = 500 ms
ENUMERATION: SLOT LETTERS
bitmask slot bitmask slot bitmask slot bitmask slot

F179
0 F 4 K 8 P 12 U ENUMERATION: NEGATIVE SEQUENCE DIRECTIONAL
1 G 5 L 9 R 13 V OVERCURRENT TYPE
2 H 6 M 10 S 14 W 0 = Neg Sequence, 1 = Zero Sequence
3 J 7 N 11 T 15 X
F180
F173 ENUMERATION: PHASE/GROUND
ENUMERATION: DCMA INPUT/OUTPUT RANGE
0 = PHASE, 1 = GROUND
bitmask dcmA input/output range
0 0 to –1 mA
F181
1 0 to 1 mA ENUMERATION: ODD/EVEN/NONE
2 –1 to 1 mA
0 = ODD, 1 = EVEN, 2 = NONE
3 0 to 5 mA
4 0 to 10 mA
5 0 to 20 mA F183
6 4 to 20 mA ENUMERATION: AC INPUT WAVEFORMS
bitmask definition
F174 0 Off
ENUMERATION: TRANSDUCER RTD INPUT TYPE 1 8 samples/cycle
0 = 100 Ohm Platinum, 1 = 120 Ohm Nickel, 2 16 samples/cycle

2 = 100 Ohm Nickel, 3 = 10 Ohm Copper 3 32 samples/cycle
4 64 samples/cycle

bitmsk keypress bitmsk keypress

F184
17 Message Left 45 User-programmable key 15
ENUMERATION: REMOTE DEVICE GOOSE DATASET
18 Message Right 46 User-programmable key 16
value GOOSE dataset 19 Menu 47 User 4 (control pushbutton)
0 Off 20 Help 48 User 5 (control pushbutton)
1 GooseIn 1 21 Escape 49 User 6 (control pushbutton)
2 GooseIn 2 22 --- 50 User 7 (control pushbutton)
3 GooseIn 3
4 GooseIn 4
F192
5 GooseIn 5 ENUMERATION: ETHERNET OPERATION MODE
6 GooseIn 6
0 = Half-Duplex, 1 = Full-Duplex
7 GooseIn 7
8
9
GooseIn 8
GooseIn 9 F194
B
10 GooseIn 10 ENUMERATION: DNP SCALE
11 GooseIn 11 0 = 0.01, 1 = 0.1, 2 = 1, 3 = 10, 4 = 100, 5 = 1000, 6 = 10000,
12 GooseIn 12 7 = 100000, 8 = 0.001
13 GooseIn 13
14 GooseIn 14
F195
15 GooseIn 15 ENUMERATION: SINGLE POLE TRIP MODE
16 GooseIn 16
0 = Disabled, 1 = 3 Pole Only, 2 = 3 Pole & 1 Pole
F185
F196
ENUMERATION: PHASE A,B,C, GROUND SELECTOR
ENUMERATION: NEUTRAL DIRECTIONAL OVERCURRENT
0 = A, 1 = B, 2 = C, 3 = G OPERATING CURRENT
0 = Calculated 3I0, 1 = Measured IG
F186
ENUMERATION: MEASUREMENT MODE F198
0 = Phase to Ground, 1 = Phase to Phase ENUMERATION: PILOT SCHEME COMMUNICATION BITS
0 = 1, 1 = 2, 2 = 4
F190
ENUMERATION: SIMULATED KEYPRESS
F199
ENUMERATION: DISABLED/ENABLED/CUSTOM
bitmsk keypress bitmsk keypress
0 --- 23 Reset 0 = Disabled, 1 = Enabled, 2 = Custom
use between real keys
24 User 1
1 1 25 User 2
F200
2 2 26 User 3 TEXT40: 40-CHARACTER ASCII TEXT
3 3 27 User-programmable key 1
20 registers, 16 Bits: 1st Char MSB, 2nd Char. LSB
6 6 30 User-programmable key 4 F201
7 7 31 User-programmable key 5 TEXT8: 8-CHARACTER ASCII PASSCODE
8 8 32 User-programmable key 6 4 registers, 16 Bits: 1st Char MSB, 2nd Char. LSB
F202
11 Decimal Point 35 User-programmable key 9
TEXT20: 20-CHARACTER ASCII TEXT
12 Plus/Minus 36 User-programmable key 10
10 registers, 16 Bits: 1st Char MSB, 2nd Char. LSB
13 Value Up 37 User-programmable key 11
14 Value Down 38 User-programmable key 12
15 Message Up 43 User-programmable key 13 F203
16 Message Down 44 User-programmable key 14 TEXT16: 16-CHARACTER ASCII TEXT

F204 F228
TEXT80: 80-CHARACTER ASCII TEXT ENUMERATION: SETTINGS CONTROL EVENT TYPE
0 = Unknown, 1 = Setting Change, 2 = Firmware Upgrade, 3 =
Hardware Change
F205
F229
ENUMERATION: SETTINGS CONTROL CHANGE METHOD
F206
TEXT6: 6-CHARACTER ASCII TEXT 0 = None, 1 = Keypad, 2 = Front Port, 3 = COM1, 4 = COM2, 5 =
Ethernet
F207
TEXT4: 4-CHARACTER ASCII TEXT F230
B ENUMERATION: DIRECTIONAL POLARIZING
0 = Voltage, 1 = Current, 2 = Dual, 3 = Dual-V, 4 = Dual-I
F208
F231
ENUMERATION: POLARIZING VOLTAGE
F211
ENUMERATION: SOURCE SELECTION 0 = Calculated V0, 1 = Measured VX
0 = None, 1 = SRC 1, 2 = SRC 2, 3 = SRC 3, 4 = SRC 4,
5 = SRC 5, 6 = SRC 6
F232
ENUMERATION: CONFIGURABLE GOOSE DATASET ITEMS
FOR TRANSMISSION
F213
value GOOSE dataset item
0 None
F220 1 GGIO1.ST.Ind1.q
ENUMERATION: PUSHBUTTON MESSAGE PRIORITY 2 GGIO1.ST.Ind1.stVal
3 GGIO1.ST.Ind2.q
value priority
4 GGIO1.ST.Ind2.stVal
0 Disabled
 
1 Normal
255 GGIO1.ST.Ind128.q
2 High Priority
257 MMXU1.MX.TotW.mag.f
F222 258 MMXU1.MX.TotVAr.mag.f
ENUMERATION: TEST ENUMERATION 259 MMXU1.MX.TotVA.mag.f
0 = Test Enumeration 0, 1 = Test Enumeration 1 260 MMXU1.MX.TotPF.mag.f

261 MMXU1.MX.Hz.mag.f
262 MMXU1.MX.PPV.phsAB.cVal.mag.f
F224 263 MMXU1.MX.PPV.phsAB.cVal.ang.f
ENUMERATION: RATE TREND FOR FREQ RATE OF CHANGE
264 MMXU1.MX.PPV.phsBC.cVal.mag.f
0 = Increasing, 1 = Decreasing, 2 = Bidirectional 265 MMXU1.MX.PPV.phsBC.cVal.ang.f
266 MMXU1.MX.PPV.phsCA.cVal.mag.f
267 MMXU1.MX.PPV.phsCA.cVal.ang.f
F226
ENUMERATION: REMOTE INPUT/OUTPUT TRANSFER 268 MMXU1.MX.PhV.phsA.cVal.mag.f
METHOD 269 MMXU1.MX.PhV.phsA.cVal.ang.f
0 = None, 1 = GSSE, 2 = GOOSE 270 MMXU1.MX.PhV.phsB.cVal.mag.f

271 MMXU1.MX.PhV.phsB.cVal.ang.f
272 MMXU1.MX.PhV.phsC.cVal.mag.f
F227 273 MMXU1.MX.PhV.phsC.cVal.ang.f
ENUMERATION: RELAY SERVICE STATUS
274 MMXU1.MX.A.phsA.cVal.mag.f
0 = Unknown, 1 = Relay In Service, 2 = Relay Out Of Service 275 MMXU1.MX.A.phsA.cVal.ang.f
276 MMXU1.MX.A.phsB.cVal.mag.f
277 MMXU1.MX.A.phsB.cVal.ang.f

value GOOSE dataset item value GOOSE dataset item

278 MMXU1.MX.A.phsC.cVal.mag.f 331 MMXU3.MX.TotW.mag.f
279 MMXU1.MX.A.phsC.cVal.ang.f 332 MMXU3.MX.TotVAr.mag.f
280 MMXU1.MX.A.neut.cVal.mag.f 333 MMXU3.MX.TotVA.mag.f
281 MMXU1.MX.A.neut.cVal.ang.f 334 MMXU3.MX.TotPF.mag.f
282 MMXU1.MX.W.phsA.cVal.mag.f 335 MMXU3.MX.Hz.mag.f
283 MMXU1.MX.W.phsB.cVal.mag.f 336 MMXU3.MX.PPV.phsAB.cVal.mag.f
284 MMXU1.MX.W.phsC.cVal.mag.f 337 MMXU3.MX.PPV.phsAB.cVal.ang.f
285 MMXU1.MX.VAr.phsA.cVal.mag.f 338 MMXU3.MX.PPV.phsBC.cVal.mag.f
286 MMXU1.MX.VAr.phsB.cVal.mag.f 339 MMXU3.MX.PPV.phsBC.cVal.ang.f
287 MMXU1.MX.VAr.phsC.cVal.mag.f 340 MMXU3.MX.PPV.phsCA.cVal.mag.f
288 MMXU1.MX.VA.phsA.cVal.mag.f 341 MMXU3.MX.PPV.phsCA.cVal.ang.f
289
290
MMXU1.MX.VA.phsB.cVal.mag.f
MMXU1.MX.VA.phsC.cVal.mag.f
342
343
MMXU3.MX.PhV.phsA.cVal.mag.f
MMXU3.MX.PhV.phsA.cVal.ang.f
B
291 MMXU1.MX.PF.phsA.cVal.mag.f 344 MMXU3.MX.PhV.phsB.cVal.mag.f
292 MMXU1.MX.PF.phsB.cVal.mag.f 345 MMXU3.MX.PhV.phsB.cVal.ang.f
293 MMXU1.MX.PF.phsC.cVal.mag.f 346 MMXU3.MX.PhV.phsC.cVal.mag.f
294 MMXU2.MX.TotW.mag.f 347 MMXU3.MX.PhV.phsC.cVal.ang.f
295 MMXU2.MX.TotVAr.mag.f 348 MMXU3.MX.A.phsA.cVal.mag.f
296 MMXU2.MX.TotVA.mag.f 349 MMXU3.MX.A.phsA.cVal.ang.f
297 MMXU2.MX.TotPF.mag.f 350 MMXU3.MX.A.phsB.cVal.mag.f
298 MMXU2.MX.Hz.mag.f 351 MMXU3.MX.A.phsB.cVal.ang.f
299 MMXU2.MX.PPV.phsAB.cVal.mag.f 352 MMXU3.MX.A.phsC.cVal.mag.f
300 MMXU2.MX.PPV.phsAB.cVal.ang.f 353 MMXU3.MX.A.phsC.cVal.ang.f
301 MMXU2.MX.PPV.phsBC.cVal.mag.f 354 MMXU3.MX.A.neut.cVal.mag.f
302 MMXU2.MX.PPV.phsBC.cVal.ang.f 355 MMXU3.MX.A.neut.cVal.ang.f
303 MMXU2.MX.PPV.phsCA.cVal.mag.f 356 MMXU3.MX.W.phsA.cVal.mag.f
304 MMXU2.MX.PPV.phsCA.cVal.ang.f 357 MMXU3.MX.W.phsB.cVal.mag.f
305 MMXU2.MX.PhV.phsA.cVal.mag.f 358 MMXU3.MX.W.phsC.cVal.mag.f
306 MMXU2.MX.PhV.phsA.cVal.ang.f 359 MMXU3.MX.VAr.phsA.cVal.mag.f
307 MMXU2.MX.PhV.phsB.cVal.mag.f 360 MMXU3.MX.VAr.phsB.cVal.mag.f
308 MMXU2.MX.PhV.phsB.cVal.ang.f 361 MMXU3.MX.VAr.phsC.cVal.mag.f
309 MMXU2.MX.PhV.phsC.cVal.mag.f 362 MMXU3.MX.VA.phsA.cVal.mag.f
310 MMXU2.MX.PhV.phsC.cVal.ang.f 363 MMXU3.MX.VA.phsB.cVal.mag.f
311 MMXU2.MX.A.phsA.cVal.mag.f 364 MMXU3.MX.VA.phsC.cVal.mag.f
312 MMXU2.MX.A.phsA.cVal.ang.f 365 MMXU3.MX.PF.phsA.cVal.mag.f
313 MMXU2.MX.A.phsB.cVal.mag.f 366 MMXU3.MX.PF.phsB.cVal.mag.f
314 MMXU2.MX.A.phsB.cVal.ang.f 367 MMXU3.MX.PF.phsC.cVal.mag.f
326 MMXU2.MX.VA.phsB.cVal.mag.f 379 MMXU4.MX.PhV.phsA.cVal.mag.f
327 MMXU2.MX.VA.phsC.cVal.mag.f 380 MMXU4.MX.PhV.phsA.cVal.ang.f

value GOOSE dataset item value GOOSE dataset item

B 395
396
MMXU4.MX.W.phsC.cVal.mag.f
MMXU4.MX.VAr.phsA.cVal.mag.f
448
449
MMXU6.MX.PPV.phsAB.cVal.ang.f
MMXU6.MX.PPV.phsBC.cVal.mag.f
426 MMXU5.MX.A.phsC.cVal.mag.f 479 GGIO4.MX.AnIn1.mag.f
427 MMXU5.MX.A.phsC.cVal.ang.f 480 GGIO4.MX.AnIn2.mag.f
428 MMXU5.MX.A.neut.cVal.mag.f 481 GGIO4.MX.AnIn3.mag.f
429 MMXU5.MX.A.neut.cVal.ang.f 482 GGIO4.MX.AnIn4.mag.f
430 MMXU5.MX.W.phsA.cVal.mag.f 483 GGIO4.MX.AnIn5.mag.f
431 MMXU5.MX.W.phsB.cVal.mag.f 484 GGIO4.MX.AnIn6.mag.f
432 MMXU5.MX.W.phsC.cVal.mag.f 485 GGIO4.MX.AnIn7.mag.f
433 MMXU5.MX.VAr.phsA.cVal.mag.f 486 GGIO4.MX.AnIn8.mag.f
434 MMXU5.MX.VAr.phsB.cVal.mag.f 487 GGIO4.MX.AnIn9.mag.f
435 MMXU5.MX.VAr.phsC.cVal.mag.f 488 GGIO4.MX.AnIn10.mag.f
436 MMXU5.MX.VA.phsA.cVal.mag.f 489 GGIO4.MX.AnIn11.mag.f


F233
490 GGIO4.MX.AnIn12.mag.f
ENUMERATION: CONFIGURABLE GOOSE DATASET ITEMS
FOR RECEPTION
493 GGIO4.MX.AnIn15.mag.f value GOOSE dataset item
494 GGIO4.MX.AnIn16.mag.f 0 None
495 GGIO4.MX.AnIn17.mag.f 1 GGIO3.ST.Ind1.q
496 GGIO4.MX.AnIn18.mag.f 2 GGIO3.ST.Ind1.stVal
497 GGIO4.MX.AnIn19.mag.f 3 GGIO3.ST.Ind2.q
498 GGIO4.MX.AnIn20.mag.f 4 GGIO3.ST.Ind2.stVal
499 GGIO4.MX.AnIn21.mag.f  
500 GGIO4.MX.AnIn22.mag.f 127 GGIO1.ST.Ind64q
501
502
GGIO4.MX.AnIn23.mag.f
128
129
GGIO1.ST.Ind64.stVal
B
503 GGIO4.MX.AnIn25.mag.f 130 GGIO3.MX.AnIn2.mag.f
511 GGIO5.ST.UIntIn1.q 138 GGIO3.MX.AnIn10.mag.f
512 GGIO5.ST.UIntIn1.stVal 139 GGIO3.MX.AnIn11.mag.f
534 GGIO5.ST.UIntIn12.stVal 161 GGIO3.ST.IndPos1.stVal
535 GGIO5.ST.UIntIn13.q 162 GGIO3.ST.IndPos2.stVal
537 GGIO5.ST.UIntIn14.q 164 GGIO3.ST.IndPos4.stVal
539 GGIO5.ST.UIntIn15.q 166 GGIO3.ST.UIntIn1.q
540 GGIO5.ST.UIntIn15.stVal 167 GGIO3.ST.UIntIn1.stVal
541 GGIO5.ST.UIntIn16.q 168 GGIO3.ST.UIntIn2.q
542 GGIO5.ST.UIntIn16.stVal 169 GGIO3.ST.UIntIn2.stVal


F237
170 GGIO3.ST.UIntIn3.q
ENUMERATION: REAL TIME CLOCK MONTH
171 GGIO3.ST.UIntIn3.stVal
172 GGIO3.ST.UIntIn4.q value month
173 GGIO3.ST.UIntIn4.stVal 0 January
174 GGIO3.ST.UIntIn5.q 1 February
175 GGIO3.ST.UIntIn5.stVal 2 March
176 GGIO3.ST.UIntIn6.q 3 April
177 GGIO3.ST.UIntIn6.stVal 4 May
178 GGIO3.ST.UIntIn7.q 5 June
179 GGIO3.ST.UIntIn7.stVal 6 July
180 GGIO3.ST.UIntIn8.q 7 August
B 181
182
GGIO3.ST.UIntIn8.stVal
GGIO3.ST.UIntIn9.q
8
9
September
October
183 GGIO3.ST.UIntIn9.stVal 10 November
184 GGIO3.ST.UIntIn10.q 11 December
187 GGIO3.ST.UIntIn11.stVal F238
ENUMERATION: REAL TIME CLOCK DAY
189 GGIO3.ST.UIntIn12.stVal value day
190 GGIO3.ST.UIntIn13.q 0 Sunday
191 GGIO3.ST.UIntIn13.stVal 1 Monday
192 GGIO3.ST.UIntIn14.q 2 Tuesday
193 GGIO3.ST.UIntIn14.stVal 3 Wednesday
194 GGIO3.ST.UIntIn15.q 4 Thursday
195 GGIO3.ST.UIntIn15.stVal 5 Friday
196 GGIO3.ST.UIntIn16.q 6 Saturday
F239
F234 ENUMERATION: REAL TIME CLOCK DAYLIGHT SAVINGS
ENUMERATION: WATTMETRIC GROUND FAULT VOLTAGE TIME START DAY INSTANCE
value voltage value instance

0 Calculated VN 0 First
1 Measured VX 1 Second
2 Third
3 Fourth
F235
ENUMERATION: WATTMETRIC GROUND FAULT CURRENT 4 Last
value current
0 Calculated IN
1 Measured IG
F243
ENUMERATION: FIELD UNIT TYPE
F236
ENUMERATION: WATTMETRIC GRN FLT CURVE 0 = CC-05, 1 = CV-05, 2 = CC-01, 3 = CV-01
0 = Definite Time, 1 = Inverse, 2 = FlexCurve A, 3 = FlexCurve B,
4 = FlexCurve C, 5 = FlexCurve D
F244
ENUMERATION: PROCESS CARD PORT
0 = H4a, 1 = H4b 2 = H3a, 3 = H3b, 4 = H2a, 5 = H2b, 6 = H1a,
7 = H1b

The values in square brackets indicate the base type with P prefix
F245 [PTTTTTTT] and the values in round brackets indicate the descrip-
ENUMERATION: TEST MODE FUNCTION tor range. The right most T bit indicates whether the type is an ON
or OFF type. There can be a total of 64 types (plus protection ele-
Value Function ments). There can be a total of 256 descriptors of each type.
0 Disabled [0] Off (0) – this is boolean FALSE value
1 Isolated [1] On (1) – this is boolean TRUE value
2 Forcible [2] CONTACT INPUTS (1 to 96)
[3] CONTACT INPUTS OFF (1 to 96)
[4] VIRTUAL INPUTS (1 to 32)
[6] VIRTUAL OUTPUTS (1 to 64
[8] CONTACT OUTPUTS
F257
[10] CONTACT OUTPUTS VOLTAGE DETECTED (1 to 64)
ENUMERATION: PROCESS CARD DSP CONFIGURATION
[11] CONTACT OUTPUTS VOLTAGE OFF DETECTED (1 to 64)
value
0
instance
CC
[12] CONTACT OUTPUTS CURRENT DETECTED (1 to 64)
[13] CONTACT OUTPUTS CURRENT OFF DETECTED (1 to 64) B
[14] REMOTE INPUTS (1 to 32)
1 CV
[16] DIRECT INPUTS (1 to 96)
2 CD
[18] REMOTE OUTPUT DNA BIT PAIRS (1 to 32)
3 VC [20] REMOTE OUTPUT UserSt BIT PAIRS (1 to 32)
4 VV [22] REMOTE DEVICE ONLINE (1 to 16)
5 VD [24] MISCELLANEOUS EQUATION
[26] TELEPROTECTION INPUTS
6 DC
[28] INSERT (via keypad only)
7 DV
[30] DELETE (via keypad only)
8 DD [32] END
[34] NOT (1 INPUT)
[36] 2 INPUT XOR (0)
F260 [38] LATCH SET/RESET (2 inputs)
ENUMERATION: DATA LOGGER MODE [40] OR (2 to 16 inputs)
[42] AND (2 to 16 inputs)
0 = Continuous, 1 = Trigger
[44] NOR (2 to 16 inputs)
[46] NAND (2 to 16 inputs)
[48] TIMER (1 to 32)
F261
[50] ASSIGN VIRTUAL OUTPUT (1 to 64)
ENUMERATION: BANK REDUNDANCY TYPE
[52] ONE SHOT
0 = None, 1 = Dependability Biased, 2 = Security Biased [54] SELF-TEST ERROR (see F141 for range)
[56] PLATFORM DIRECT INPUT (1 to 96)
[58] PLATFORM DIRECT OUTPUT (1 to 96)
F263 [60] PLATFORM DIRECT DEVICE (1 to 8)
ENUMERATION: PROCESS BUS SYSTEM STATUS [62] MISCELLANEOUS EVENTS (see F146 for range)
[64] PDC NETWORK CONTROL
0 = N/A, 1 = OK, 2 = Fail
[66] PMU RECORDERE OUT OF MEMORY
[68] PMU RECORDER STOPPED
[128 to 255] ELEMENT STATES (see memory map element states
F270
section)
ENUMERATION: FAULT REPORT VT SUBSTITUTION
Value Description
F400
0 None UR_UINT16: CT/VT BANK SELECTION
1 I_0
bitmask bank selection
2 V_0
0 Card 1 Contact 1 to 4
1 Card 1 Contact 5 to 8
F300 2 Card 2 Contact 1 to 4
UR_UINT32: FLEXLOGIC BASE TYPE (15-bit type) 3 Card 2 Contact 5 to 8
The FlexLogic BASE type is 7 bits and is combined with an 8-bit 4 Card 3 Contact 1 to 4
descriptor and 1 bit for protection element to form a 16-bit value. 5 Card 3 Contact 5 to 8
The combined bits are of the form: PTTTTTTTDDDDDDDD,
where P bit if set, indicates that the FlexLogic type is associated
with a protection element state and T represents bits for the BASE F491
type, and D represents bits for the descriptor. ENUMERATION: ANALOG INPUT MODE
0 = Default Value, 1 = Last Known

F508
F500 BITFIELD: DISTANCE ELEMENT STATE
UR_UINT16: PACKED BITFIELD bitmask distance element state
First register indicates input/output state with bits 0 (MSB) to 15 0 Pickup
(LSB) corresponding to input/output state 1 to 16. The second reg- 1 Operate
ister indicates input/output state with bits 0 to 15 corresponding to 2 Pickup AB
input/output state 17 to 32 (if required) The third register indicates
3 Pickup BC
input/output state with bits 0 to 15 corresponding to input/output
state 33 to 48 (if required). The fourth register indicates input/out- 4 Pickup CA
put state with bits 0 to 15 corresponding to input/output state 49 to 5 Operate AB
64 (if required). 6 Operate BC
The number of registers required is determined by the specific 7 Operate CA
data item. A bit value of 0 = Off and 1 = On.
B
8 Timed
9 Operate IAB
10 Operate IBC
F501
UR_UINT16: LED STATUS 11 Operate ICA
Low byte of register indicates LED status with bit 0 representing

the top LED and bit 7 the bottom LED. A bit value of 1 indicates
F509
the LED is on, 0 indicates the LED is off. BITFIELD: SIMPLE ELEMENT STATE
0 = Operate
F502
BITFIELD: ELEMENT OPERATE STATES
F511
Each bit contains the operate state for an element. See the F124 BITFIELD: 3-PHASE SIMPLE ELEMENT STATE
format code for a list of element IDs. The operate bit for element ID
X is bit [X mod 16] in register [X/16]. 0 = Operate, 1 = Operate A, 2 = Operate B, 3 = Operate C
F504 F512
BITFIELD: 3-PHASE ELEMENT STATE ENUMERATION: HARMONIC NUMBER
bitmask element state
bitmask harmonic bitmask harmonic
0 Pickup
0 2ND 12 14TH
1 Operate
1 3RD 13 15TH
2 Pickup Phase A
2 4TH 14 16TH
3 Pickup Phase B
3 5TH 15 17TH
4 Pickup Phase C
4 6TH 16 18TH
5 Operate Phase A
5 7TH 17 19TH
6 Operate Phase B
6 8TH 18 20TH
7 Operate Phase C
7 9TH 19 21ST
8 10TH 20 22ND
9 11TH 21 23RD
F505
BITFIELD: CONTACT OUTPUT STATE 10 12TH 22 24TH
11 13TH 23 25TH
0 = Contact State, 1 = Voltage Detected, 2 = Current Detected
F513
F506|
ENUMERATION: POWER SWING MODE
BITFIELD: SINGLE-PHASE ELEMENT STATE
0 = Two Step, 1 = Three Step
0 = Pickup, 1 = Operate
F514
F507
BITFIELD: COUNTER ELEMENT STATE ENUMERATION: POWER SWING TRIP MODE
0 = Count Greater Than, 1 = Count Equal To, 2 = Count Less Than 0 = Delayed, 1 = Early

F515 F525
ENUMERATION ELEMENT INPUT MODE ENUMERATION: DNP OBJECT 32 DEFAULT VARIATION
0 = Signed, 1 = Absolute
bitmask default variation
0 1
F516 1 2
ENUMERATION ELEMENT COMPARE MODE 2 3
0 = Level, 1 = Delta 3 4
4 5
5 7
F517
ENUMERATION: ELEMENT DIRECTION OPERATION
F530
0 = Over, 1 = Under
ENUMERATION: FRONT PANEL INTERFACE KEYPRESS B
value keypress value keypress value keypress
F518 0 None 15 3 33 User PB 3
ENUMERATION: FLEXELEMENT UNITS
1 Menu 16 Enter 34 User PB 4
0 = Milliseconds, 1 = Seconds, 2 = Minutes 2 Message Up 17 Message 35 User PB 5
Down
3 7 ~
18 0 ~
36 User PB 6
F519 4 8 19 Decimal 37 User PB 7
ENUMERATION: NON-VOLATILE LATCH
5 9 20 +/– 38 User PB 8
0 = Reset-Dominant, 1 = Set-Dominant 6 Help 21 Value Up 39 User PB 9
7 Message Left 22 Value Down 40 User PB 10
8 4 23 Reset 41 User PB 11
F521
ENUMERATION: GROUND DISTANCE POLARIZING CURRENT 9 5 24 User 1 42 User PB 12
10 6 25 User 2 44 User 4
0 = Zero-Sequence; 1 = Negative-Sequence
11 Escape 26 User 3 45 User 5
12 Message 31 User PB 1 46 User 6
Right
F522
ENUMERATION: TRANSDUCER DCMA OUTPUT RANGE 13 1 32 User PB 2 47 User 7
14 2
0 = –1 to 1 mA; 1 = 0 to 1 mA; 2 = 4 to 20 mA
F523 F531
ENUMERATION: LANGUAGE
ENUMERATION: DNP OBJECTS 20, 22, AND 23 DEFAULT
VARIATION 0 = English, 1 = French, 2 = Chinese, 3 = Russian, 4 = Turkish
bitmask default variation

0 1 F540
1 2 ENUMERATION: PMU POST-FILTER
2 5 0 = None, 1 = Symm-3-Point, 2 = Symm-5-Point,
3 6 3 = Symm-7-Point, 4 = Class M, 5 = Class P
F524 F542
ENUMERATION: DNP OBJECT 21 DEFAULT VARIATION ENUMERATION: PMU TRIGGERING MODE
0 = Automatic Overwrite, 1 = Protected
bitmask Default Variation
0 1
1 2
2 9
3 10

F543 F605
ENUMERATION: PMU PHASORS ENUMERATION: REMOTE DOUBLE-POINT STATUS INPUT
STATUS
value phasor value phasor
0 Off 8 Ig Enumeration Remote DPS input status
1 Va 9 V_1 0 Intermediate
2 Vb 10 V_2 1 Off
3 Vc 11 V_0 2 On
4 Vx 12 I_1 3 Bad
5 Ia 13 I_2
6 Ib 14 I_0
F606
7 Ic ENUMERATION: REMOTE DOUBLE-POINT STATUS INPUT
B Enumeration Remote double-point status input

F544 0 None
ENUMERATION: PMU RECORDING/REPORTING RATE
1 Remote input 1
value rate value rate 2 Remote input 2
0 1/second 7 20second 3 Remote input 3
1 2/second 8 25/second  
2 4/second 9 30/second 64 Remote input 64
3 5/second 10 50/second
F607
5 12/second 12 100/second ENUMERATION: OPEN POLE DETECTOR MODE
Enumeration Open Pole Mode
0 Accelerated
F545 1 Traditional
ENUMERATION: PMU COM PORT TYPE
0 = Network, 1 = RS485, 2 = Dir Comm Ch1, 3 = Dir Comm Ch2,
4 = GOOSE, 5 = None F608
ENUMERATION: OPEN POLE DETECTION FUNCTION
F546 Enumeration Open Pole Detection

ENUMERATION: PMU REPORTING STYLE 0 I AND V AND CBaux
1 I AND V only
0 = Polar, 1 = Rectangular
F547 F609
ENUMERATION: TRIP OUTPUT TRIP RESET FUNCTION
ENUMERATION: PMU REPORTING FORMAT
0 = Integer, 1 = Floating Enumeration Trip Reset
0 Pole Curr OR Custom
1 CBaux OR Custom
F600
2 Custom
UR_UINT16: FLEXANALOG PARAMETER
Corresponds to the Modbus address of the value used when this
parameter is selected. Only certain values may be used as Flex- F610
Analogs (basically all metering quantities used in protection). ENUMERATION: SINGLE-POLE AUTORECLOSE INITIATION
MODE
Enumeration Initiation Mode

0 Protection AND CB
1 Protection Only

Enumeration IEC 61850 report dataset items

F611
34 PIOC3.ST.Op.general
ENUMERATION: GOOSE RETRANSMISSION SCHEME
35 PIOC4.ST.Str.general
Enumeration Configurable GOOSE retransmission scheme 36 PIOC4.ST.Op.general
0 Heartbeat 37 PIOC5.ST.Str.general
1 Aggressive 38 PIOC5.ST.Op.general
2 Medium 39 PIOC6.ST.Str.general
3 Relaxed 40 PIOC6.ST.Op.general
F612
UR_UINT16: FLEXINTEGER PARAMETER
This 16-bit value corresponds to the Modbus address of the
selected FlexInteger parameter. Only certain values may be used
45
46
PIOC9.ST.Str.general
PIOC9.ST.Op.general
B
as FlexIntegers.
F615 49 PIOC11.ST.Str.general
ENUMERATION: IEC 61850 REPORT DATASET ITEMS
Enumeration IEC 61850 report dataset items 51 PIOC12.ST.Str.general
0 None 52 PIOC12.ST.Op.general
1 PDIF1.ST.Str.general 53 PIOC13.ST.Str.general
2 PDIF1.ST.Op.general 54 PIOC13.ST.Op.general
9 PDIS1.ST.Str.general 61 PIOC17.ST.Str.general
10 PDIS1.ST.Op.general 62 PIOC17.ST.Op.general
29 PIOC1.ST.Str.general 81 PIOC27.ST.Str.general
30 PIOC1.ST.Op.general 82 PIOC27.ST.Op.general
32 PIOC2.ST.Op.general 84 PIOC28.ST.Op.general

Enumeration IEC 61850 report dataset items Enumeration IEC 61850 report dataset items
87 PIOC30.ST.Str.general 140 PIOC56.ST.Op.general
88 PIOC30.ST.Op.general 141 PIOC57.ST.Str.general
B 98
99
PIOC35.ST.Op.general
151
152
120 PIOC46.ST.Op.general 173 PTOC1.ST.Str.general
121 PIOC47.ST.Str.general 174 PTOC1.ST.Op.general

193 PTOC11.ST.Str.general 246 PTRC3.ST.Op.general
194 PTOC11.ST.Op.general 247 PTRC4.ST.Tr.general
200 PTOC14.ST.Op.general 253 PTUV1.ST.Str.general
201 PTOC15.ST.Str.general 254 PTUV1.ST.Op.general
204
205
PTOC16.ST.Op.general
PTOC17.ST.Str.general
257
258
PTUV3.ST.Str.general
PTUV3.ST.Op.general
B
221 PTOV1.ST.Str.general 274 PTUV11.ST.Op.general
222 PTOV1.ST.Op.general 275 PTUV12.ST.Str.general
226 PTOV3.ST.Op.general 279 RBRF1.ST.OpEx.general
227 PTOV4.ST.Str.general 280 RBRF1.ST.OpIn.general
241 PTRC1.ST.Tr.general 294 RBRF8.ST.OpIn.general
242 PTRC1.ST.Op.general 295 RBRF9.ST.OpEx.general
244 PTRC2.ST.Op.general 297 RBRF10.ST.OpEx.general

299 RBRF11.ST.OpEx.general 352 CSWI3.ST.Pos.stVal
300 RBRF11.ST.OpIn.general 353 CSWI4.ST.Loc.stVal
B 310
311
RBRF16.ST.OpIn.general
RBRF17.ST.OpEx.general
363
364
CSWI9.ST.Loc.stVal
CSWI9.ST.Pos.stVal
327 RFLO1.MX.FltDiskm.mag.f 380 CSWI17.ST.Pos.stVal
328 RFLO2.MX.FltDiskm.mag.f 381 CSWI18.ST.Loc.stVal
332 RPSB1.ST.Str.general 385 CSWI20.ST.Loc.stVal
333 RPSB1.ST.Op.general 386 CSWI20.ST.Pos.stVal
334 RPSB1.ST.BlkZn.stVal 387 CSWI21.ST.Loc.stVal
335 RREC1.ST.Op.general 388 CSWI21.ST.Pos.stVal
336 RREC1.ST.AutoRecSt.stVal 389 CSWI22.ST.Loc.stVal
347 CSWI1.ST.Loc.stVal 400 CSWI27.ST.Pos.stVal
348 CSWI1.ST.Pos.stVal 401 CSWI28.ST.Loc.stVal
350 CSWI2.ST.Pos.stVal 403 CSWI29.ST.Loc.stVal

405 CSWI30.ST.Loc.stVal 458 GGIO1.ST.Ind52.stVal
406 CSWI30.ST.Pos.stVal 459 GGIO1.ST.Ind53.stVal
407 GGIO1.ST.Ind1.stVal 460 GGIO1.ST.Ind54.stVal
416
417
469
470
B

511 GGIO1.ST.Ind105.stVal 564 MMXU1.MX.VAr.phsB.cVal.mag.f
512 GGIO1.ST.Ind106.stVal 565 MMXU1.MX.VAr.phsC.cVal.mag.f
513 GGIO1.ST.Ind107.stVal 566 MMXU1.MX.VA.phsA.cVal.mag.f
514 GGIO1.ST.Ind108.stVal 567 MMXU1.MX.VA.phsB.cVal.mag.f
515 GGIO1.ST.Ind109.stVal 568 MMXU1.MX.VA.phsC.cVal.mag.f
516 GGIO1.ST.Ind110.stVal 569 MMXU1.MX.PF.phsA.cVal.mag.f
517 GGIO1.ST.Ind111.stVal 570 MMXU1.MX.PF.phsB.cVal.mag.f
518 GGIO1.ST.Ind112.stVal 571 MMXU1.MX.PF.phsC.cVal.mag.f
519 GGIO1.ST.Ind113.stVal 572 MMXU2.MX.TotW.mag.f
520 GGIO1.ST.Ind114.stVal 573 MMXU2.MX.TotVAr.mag.f
521 GGIO1.ST.Ind115.stVal 574 MMXU2.MX.TotVA.mag.f
B 522
523
575
576
MMXU2.MX.TotPF.mag.f
MMXU2.MX.Hz.mag.f
524 GGIO1.ST.Ind118.stVal 577 MMXU2.MX.PPV.phsAB.cVal.mag.f
525 GGIO1.ST.Ind119.stVal 578 MMXU2.MX.PPV.phsAB.cVal.ang.f
526 GGIO1.ST.Ind120.stVal 579 MMXU2.MX.PPV.phsBC.cVal.mag.f
527 GGIO1.ST.Ind121.stVal 580 MMXU2.MX.PPV.phsBC.cVal.ang.f
528 GGIO1.ST.Ind122.stVal 581 MMXU2.MX.PPV.phsCA.cVal.mag.f
529 GGIO1.ST.Ind123.stVal 582 MMXU2.MX.PPV.phsCA.cVal.ang.f
530 GGIO1.ST.Ind124.stVal 583 MMXU2.MX.PhV.phsA.cVal.mag.f
531 GGIO1.ST.Ind125.stVal 584 MMXU2.MX.PhV.phsA.cVal.ang.f
532 GGIO1.ST.Ind126.stVal 585 MMXU2.MX.PhV.phsB.cVal.mag.f
533 GGIO1.ST.Ind127.stVal 586 MMXU2.MX.PhV.phsB.cVal.ang.f
534 GGIO1.ST.Ind128.stVal 587 MMXU2.MX.PhV.phsC.cVal.mag.f

628
629
MMXU3.MX.A.phsB.cVal.mag.f
MMXU3.MX.A.phsB.cVal.ang.f
681
682
MMXU4.MX.PF.phsB.cVal.mag.f
MMXU4.MX.PF.phsC.cVal.mag.f
B

723 MMXU6.MX.TotPF.mag.f 776 GGIO4.MX.AnIn20.mag.f
724 MMXU6.MX.Hz.mag.f 777 GGIO4.MX.AnIn21.mag.f
725 MMXU6.MX.PPV.phsAB.cVal.mag.f 778 GGIO4.MX.AnIn22.mag.f
726 MMXU6.MX.PPV.phsAB.cVal.ang.f 779 GGIO4.MX.AnIn23.mag.f
727 MMXU6.MX.PPV.phsBC.cVal.mag.f 780 GGIO4.MX.AnIn24.mag.f
728 MMXU6.MX.PPV.phsBC.cVal.ang.f 781 GGIO4.MX.AnIn25.mag.f
729 MMXU6.MX.PPV.phsCA.cVal.mag.f 782 GGIO4.MX.AnIn26.mag.f
730 MMXU6.MX.PPV.phsCA.cVal.ang.f 783 GGIO4.MX.AnIn27.mag.f
731 MMXU6.MX.PhV.phsA.cVal.mag.f 784 GGIO4.MX.AnIn28.mag.f
732 MMXU6.MX.PhV.phsA.cVal.ang.f 785 GGIO4.MX.AnIn29.mag.f
733 MMXU6.MX.PhV.phsB.cVal.mag.f 786 GGIO4.MX.AnIn30.mag.f
B 734
735
MMXU6.MX.PhV.phsB.cVal.ang.f
MMXU6.MX.PhV.phsC.cVal.mag.f
787
788
736 MMXU6.MX.PhV.phsC.cVal.ang.f 789 XSWI1.ST.Loc.stVal
737 MMXU6.MX.A.phsA.cVal.mag.f 790 XSWI1.ST.Pos.stVal
738 MMXU6.MX.A.phsA.cVal.ang.f 791 XSWI2.ST.Loc.stVal
739 MMXU6.MX.A.phsB.cVal.mag.f 792 XSWI2.ST.Pos.stVal
740 MMXU6.MX.A.phsB.cVal.ang.f 793 XSWI3.ST.Loc.stVal
741 MMXU6.MX.A.phsC.cVal.mag.f 794 XSWI3.ST.Pos.stVal
742 MMXU6.MX.A.phsC.cVal.ang.f 795 XSWI4.ST.Loc.stVal
743 MMXU6.MX.A.neut.cVal.mag.f 796 XSWI4.ST.Pos.stVal
744 MMXU6.MX.A.neut.cVal.ang.f 797 XSWI5.ST.Loc.stVal
745 MMXU6.MX.W.phsA.cVal.mag.f 798 XSWI5.ST.Pos.stVal
746 MMXU6.MX.W.phsB.cVal.mag.f 799 XSWI6.ST.Loc.stVal
747 MMXU6.MX.W.phsC.cVal.mag.f 800 XSWI6.ST.Pos.stVal
748 MMXU6.MX.VAr.phsA.cVal.mag.f 801 XSWI7.ST.Loc.stVal
749 MMXU6.MX.VAr.phsB.cVal.mag.f 802 XSWI7.ST.Pos.stVal
750 MMXU6.MX.VAr.phsC.cVal.mag.f 803 XSWI8.ST.Loc.stVal
751 MMXU6.MX.VA.phsA.cVal.mag.f 804 XSWI8.ST.Pos.stVal
752 MMXU6.MX.VA.phsB.cVal.mag.f 805 XSWI9.ST.Loc.stVal
753 MMXU6.MX.VA.phsC.cVal.mag.f 806 XSWI9.ST.Pos.stVal
754 MMXU6.MX.PF.phsA.cVal.mag.f 807 XSWI10.ST.Loc.stVal
755 MMXU6.MX.PF.phsB.cVal.mag.f 808 XSWI10.ST.Pos.stVal
756 MMXU6.MX.PF.phsC.cVal.mag.f 809 XSWI11.ST.Loc.stVal
757 GGIO4.MX.AnIn1.mag.f 810 XSWI11.ST.Pos.stVal
758 GGIO4.MX.AnIn2.mag.f 811 XSWI12.ST.Loc.stVal

Enumeration IEC 61850 report dataset items Enumeration GOOSE dataset items
829 XSWI21.ST.Loc.stVal 28 GGIO1.ST.Ind14.stVal
830 XSWI21.ST.Pos.stVal 29 GGIO1.ST.Ind15.q
837 XCBR1.ST.Loc.stVal 36 GGIO1.ST.Ind18.stVal
838 XCBR1.ST.Pos.stVal 37 GGIO1.ST.Ind19.q
840
841
XCBR2.ST.Pos.stVal
XCBR3.ST.Loc.stVal
39
40
GGIO1.ST.Ind20.q
B
49 GGIO1.ST.Ind25.q
F616
ENUMERATION: IEC 61850 GOOSE DATASET ITEMS
51 GGIO1.ST.Ind26.q
Enumeration GOOSE dataset items 52 GGIO1.ST.Ind26.stVal
0 None 53 GGIO1.ST.Ind27.q
1 GGIO1.ST.Ind1.q 54 GGIO1.ST.Ind27.stVal
2 GGIO1.ST.Ind1.stVal 55 GGIO1.ST.Ind28.q

Enumeration GOOSE dataset items Enumeration GOOSE dataset items

B 92
93
GGIO1.ST.Ind47.q
145
146
GGIO1.ST.Ind73.q


198
199
GGIO1.ST.Ind100.q
251
252
GGIO1.ST.Ind126.q
B
204 GGIO1.ST.Ind102.stVal 257 MMXU1.MX.TotW.mag.f
205 GGIO1.ST.Ind103.q 258 MMXU1.MX.TotVAr.mag.f
206 GGIO1.ST.Ind103.stVal 259 MMXU1.MX.TotVA.mag.f
207 GGIO1.ST.Ind104.q 260 MMXU1.MX.TotPF.mag.f
208 GGIO1.ST.Ind104.stVal 261 MMXU1.MX.Hz.mag.f
209 GGIO1.ST.Ind105.q 262 MMXU1.MX.PPV.phsAB.cVal.mag.f
210 GGIO1.ST.Ind105.stVal 263 MMXU1.MX.PPV.phsAB.cVal.ang.f
211 GGIO1.ST.Ind106.q 264 MMXU1.MX.PPV.phsBC.cVal.mag.f
212 GGIO1.ST.Ind106.stVal 265 MMXU1.MX.PPV.phsBC.cVal.ang.f
213 GGIO1.ST.Ind107.q 266 MMXU1.MX.PPV.phsCA.cVal.mag.f
214 GGIO1.ST.Ind107.stVal 267 MMXU1.MX.PPV.phsCA.cVal.ang.f
215 GGIO1.ST.Ind108.q 268 MMXU1.MX.PhV.phsA.cVal.mag.f
216 GGIO1.ST.Ind108.stVal 269 MMXU1.MX.PhV.phsA.cVal.ang.f
217 GGIO1.ST.Ind109.q 270 MMXU1.MX.PhV.phsB.cVal.mag.f
218 GGIO1.ST.Ind109.stVal 271 MMXU1.MX.PhV.phsB.cVal.ang.f
219 GGIO1.ST.Ind110.q 272 MMXU1.MX.PhV.phsC.cVal.mag.f
220 GGIO1.ST.Ind110.stVal 273 MMXU1.MX.PhV.phsC.cVal.ang.f
221 GGIO1.ST.Ind111.q 274 MMXU1.MX.A.phsA.cVal.mag.f
222 GGIO1.ST.Ind111.stVal 275 MMXU1.MX.A.phsA.cVal.ang.f
223 GGIO1.ST.Ind112.q 276 MMXU1.MX.A.phsB.cVal.mag.f
224 GGIO1.ST.Ind112.stVal 277 MMXU1.MX.A.phsB.cVal.ang.f
225 GGIO1.ST.Ind113.q 278 MMXU1.MX.A.phsC.cVal.mag.f
226 GGIO1.ST.Ind113.stVal 279 MMXU1.MX.A.phsC.cVal.ang.f
227 GGIO1.ST.Ind114.q 280 MMXU1.MX.A.neut.cVal.mag.f
228 GGIO1.ST.Ind114.stVal 281 MMXU1.MX.A.neut.cVal.ang.f
229 GGIO1.ST.Ind115.q 282 MMXU1.MX.W.phsA.cVal.mag.f
230 GGIO1.ST.Ind115.stVal 283 MMXU1.MX.W.phsB.cVal.mag.f
231 GGIO1.ST.Ind116.q 284 MMXU1.MX.W.phsC.cVal.mag.f
232 GGIO1.ST.Ind116.stVal 285 MMXU1.MX.VAr.phsA.cVal.mag.f
233 GGIO1.ST.Ind117.q 286 MMXU1.MX.VAr.phsB.cVal.mag.f
234 GGIO1.ST.Ind117.stVal 287 MMXU1.MX.VAr.phsC.cVal.mag.f
235 GGIO1.ST.Ind118.q 288 MMXU1.MX.VA.phsA.cVal.mag.f
236 GGIO1.ST.Ind118.stVal 289 MMXU1.MX.VA.phsB.cVal.mag.f
237 GGIO1.ST.Ind119.q 290 MMXU1.MX.VA.phsC.cVal.mag.f
238 GGIO1.ST.Ind119.stVal 291 MMXU1.MX.PF.phsA.cVal.mag.f
239 GGIO1.ST.Ind120.q 292 MMXU1.MX.PF.phsB.cVal.mag.f


B 304
305
MMXU2.MX.PPV.phsCA.cVal.ang.f
MMXU2.MX.PhV.phsA.cVal.mag.f
357
358
MMXU3.MX.W.phsB.cVal.mag.f
MMXU3.MX.W.phsC.cVal.mag.f


410
411
MMXU5.MX.PPV.phsAB.cVal.mag.f
MMXU5.MX.PPV.phsAB.cVal.ang.f
463
464
MMXU6.MX.A.phsC.cVal.mag.f
MMXU6.MX.A.phsC.cVal.ang.f
B
426 MMXU5.MX.A.phsC.cVal.mag.f 479 GGIO4.MX.AnIn1.mag.f
427 MMXU5.MX.A.phsC.cVal.ang.f 480 GGIO4.MX.AnIn2.mag.f
428 MMXU5.MX.A.neut.cVal.mag.f 481 GGIO4.MX.AnIn3.mag.f
429 MMXU5.MX.A.neut.cVal.ang.f 482 GGIO4.MX.AnIn4.mag.f
430 MMXU5.MX.W.phsA.cVal.mag.f 483 GGIO4.MX.AnIn5.mag.f
431 MMXU5.MX.W.phsB.cVal.mag.f 484 GGIO4.MX.AnIn6.mag.f
432 MMXU5.MX.W.phsC.cVal.mag.f 485 GGIO4.MX.AnIn7.mag.f
433 MMXU5.MX.VAr.phsA.cVal.mag.f 486 GGIO4.MX.AnIn8.mag.f
434 MMXU5.MX.VAr.phsB.cVal.mag.f 487 GGIO4.MX.AnIn9.mag.f
435 MMXU5.MX.VAr.phsC.cVal.mag.f 488 GGIO4.MX.AnIn10.mag.f
436 MMXU5.MX.VA.phsA.cVal.mag.f 489 GGIO4.MX.AnIn11.mag.f
437 MMXU5.MX.VA.phsB.cVal.mag.f 490 GGIO4.MX.AnIn12.mag.f
438 MMXU5.MX.VA.phsC.cVal.mag.f 491 GGIO4.MX.AnIn13.mag.f
439 MMXU5.MX.PF.phsA.cVal.mag.f 492 GGIO4.MX.AnIn14.mag.f
440 MMXU5.MX.PF.phsB.cVal.mag.f 493 GGIO4.MX.AnIn15.mag.f
441 MMXU5.MX.PF.phsC.cVal.mag.f 494 GGIO4.MX.AnIn16.mag.f
442 MMXU6.MX.TotW.mag.f 495 GGIO4.MX.AnIn17.mag.f
443 MMXU6.MX.TotVAr.mag.f 496 GGIO4.MX.AnIn18.mag.f
444 MMXU6.MX.TotVA.mag.f 497 GGIO4.MX.AnIn19.mag.f
445 MMXU6.MX.TotPF.mag.f 498 GGIO4.MX.AnIn20.mag.f
446 MMXU6.MX.Hz.mag.f 499 GGIO4.MX.AnIn21.mag.f
447 MMXU6.MX.PPV.phsAB.cVal.mag.f 500 GGIO4.MX.AnIn22.mag.f
448 MMXU6.MX.PPV.phsAB.cVal.ang.f 501 GGIO4.MX.AnIn23.mag.f
449 MMXU6.MX.PPV.phsBC.cVal.mag.f 502 GGIO4.MX.AnIn24.mag.f
450 MMXU6.MX.PPV.phsBC.cVal.ang.f 503 GGIO4.MX.AnIn25.mag.f
451 MMXU6.MX.PPV.phsCA.cVal.mag.f 504 GGIO4.MX.AnIn26.mag.f


505 GGIO4.MX.AnIn27.mag.f 558 PDIS4.ST.Op.general
506 GGIO4.MX.AnIn28.mag.f 559 PDIS5.ST.Str.general
511 GGIO5.ST.UIntIn1.q 564 PDIS7.ST.Op.general
512 GGIO5.ST.UIntIn1.stVal 565 PDIS8.ST.Str.general
514 GGIO5.ST.UIntIn2.stVal 567 PDIS9.ST.Str.general
B 516
517
GGIO5.ST.UIntIn3.stVal
GGIO5.ST.UIntIn4.q
569
570
PDIS10.ST.Str.general
PDIS10.ST.Op.general
518 GGIO5.ST.UIntIn4.stVal 571 PIOC1.ST.Str.general
519 GGIO5.ST.UIntIn5.q 572 PIOC1.ST.Op.general
543 PDIF1.ST.Str.general 596 PIOC13.ST.Op.general
544 PDIF1.ST.Op.general 597 PIOC14.ST.Str.general
551 PDIS1.ST.Str.general 604 PIOC17.ST.Op.general
552 PDIS1.ST.Op.general 605 PIOC18.ST.Str.general


622
623
675
676
B


717 PTOC2.ST.Str.general 770 PTOV4.ST.Op.general
718 PTOC2.ST.Op.general 771 PTOV5.ST.Str.general
B 728
729
PTOC7.ST.Op.general
PTOC8.ST.Str.general
781
782
PTOV10.ST.Str.general
PTOV10.ST.Op.general


823 RBRF2.ST.OpEx.general 876 RPSB1.ST.BlkZn.stVal
824 RBRF2.ST.OpIn.general 877 RREC1.ST.Op.general
825 RBRF3.ST.OpEx.general 878 RREC1.ST.AutoRecSt.stVal
834
835
RBRF7.ST.OpIn.general
RBRF8.ST.OpEx.general
887
888
RREC6.ST.Op.general
RREC6.ST.AutoRecSt.stVal
B
874 RPSB1.ST.Str.general 927 CSWI20.ST.Loc.stVal
875 RPSB1.ST.Op.general 928 CSWI20.ST.Pos.stVal


929 CSWI21.ST.Loc.stVal 980 XSWI16.ST.Pos.stVal
930 CSWI21.ST.Pos.stVal 981 XSWI17.ST.Loc.stVal
B 940
941
CSWI26.ST.Pos.stVal
CSWI27.ST.Loc.stVal
991
992
XSWI22.ST.Loc.stVal
XSWI22.ST.Pos.stVal
946 CSWI29.ST.Pos.stVal 997 XCBR1.ST.Loc.stVal
947 CSWI30.ST.Loc.stVal 998 XCBR1.ST.Pos.stVal
948 CSWI30.ST.Pos.stVal 999 XCBR2.ST.Loc.stVal
949 XSWI1.ST.Loc.stVal 1000 XCBR2.ST.Pos.stVal
950 XSWI1.ST.Pos.stVal 1001 XCBR3.ST.Loc.stVal
958 XSWI5.ST.Pos.stVal
959 XSWI6.ST.Loc.stVal
F617
ENUMERATION: LOGIN ROLES
962 XSWI7.ST.Pos.stVal Enumeration Role
963 XSWI8.ST.Loc.stVal 0 None
964 XSWI8.ST.Pos.stVal 1 Administrator
965 XSWI9.ST.Loc.stVal 2 Supervisor
966 XSWI9.ST.Pos.stVal 3 Engineer
967 XSWI10.ST.Loc.stVal 4 Operator
968 XSWI10.ST.Pos.stVal 5 Factory
F620
971 XSWI12.ST.Loc.stVal ENUMERATION: PASSWORD CHANGE ROLES
973 XSWI13.ST.Loc.stVal Enumeration Role
974 XSWI13.ST.Pos.stVal 0 None
975 XSWI14.ST.Loc.stVal 1 Administrator
976 XSWI14.ST.Pos.stVal 2 Supervisor
977 XSWI15.ST.Loc.stVal 3 Engineer
978 XSWI15.ST.Pos.stVal 4 Operator

F621 F625
ENUMERATION: MODBUS LOGIN ROLES ENUMERATION: PTP STATE
Enumeration Role Enumeration Item

0 None 0 Disabled
1 Administrator 1 No Signal
2 Supervisor 2 Calibrating
3 Engineer 3 Synchronized
4 Operator 4 Synchronized (No PDelay)
5 Observer
6 Factory Service
F626
ENUMERATION: NETWORK PORT FOR REMOTE DEVICE
F622
Enumeration Item
B
ENUMERATION: AUTORECLOSE 1P 3P MODE AUTOMATED
0 None
Enumeration Mode 1 Network Port 1
0 Mode 1 (1 and 3 Pole) 2 Network Port 2
1 Mode 2 (1 Pole) 3 Network Port 3
2 Mode 3 (3 Pole - A)
3 Mode 4 (3 Pole - B)
F627
ENUMERATION: REDUNDANCY MODE
F623
Enumeration Item
ENUMERATION: RTC SYNCHRONIZING SOURCE CONFIGU-
RATION 0 None
1 Failover
Enumeration Item 2 PRP
0 None
1 PP/IRIG-B/PTP/SNTP
F626
2 IRIG-B/PP/PTP/SNTP
ENUMERATION: SECURITY BYPASS ACCESS (disables secu-
3 PP/PTP/IRIG-B/SNTP
rity on local access, remoted access, or both)
Enumeration Item
F624
0 Disabled
ENUMERATION: RTC SYNCHRONZING SOURCE ACTUALS
1 Local and Remote
Enumeration Item 2 Local
0 None 3 Remote
1 Port 1 PTP Clock
2 Port 2 PTP Clock
3 Port 3 PTP Clock
4 IRIG-B
5 SNTP


APPENDIX C C.1 OVERVIEW
APPENDIX C IEC 61850 COMMUNICATIONSC.1OVERVIEW C.1.1 INTRODUCTION
The IEC 61850 standard is the result of electric utilities and vendors of electronic equipment to produce standardized com-
munications systems. IEC 61850 is a series of standards describing client/server and peer-to-peer communications, sub-
station design and configuration, testing, environmental and project standards. The complete set includes:
• IEC 61850-1: Introduction and overview
• IEC 61850-2: Glossary
• IEC 61850-3: General requirements
• IEC 61850-4: System and project management
• IEC 61850-5: Communications and requirements for functions and device models
•
•
IEC 61850-6: Configuration description language for communication in electrical substations related to IEDs
IEC 61850-7-1: Basic communication structure for substation and feeder equipment - Principles and models
C
• IEC 61850-7-2: Basic communication structure for substation and feeder equipment - Abstract communication service
interface (ACSI)
• IEC 61850-7-3: Basic communication structure for substation and feeder equipment – Common data classes
• IEC 61850-7-4: Basic communication structure for substation and feeder equipment – Compatible logical node classes
and data classes
• IEC 61850-8-1: Specific Communication Service Mapping (SCSM) – Mappings to MMS (ISO 9506-1 and ISO 9506-2)
and to ISO/IEC 8802-3
• IEC 61850-9-1: Specific Communication Service Mapping (SCSM) – Sampled values over serial unidirectional multi-
drop point to point link
• IEC 61850-9-2: Specific Communication Service Mapping (SCSM) – Sampled values over ISO/IEC 8802-3
• IEC 61850-10: Conformance testing
These documents can be obtained from the IEC (http://www.iec.ch). It is strongly recommended that all those involved with
any IEC 61850 implementation obtain this document set.
C.1.2 COMMUNICATION PROFILES
IEC 61850 specifies the use of the Manufacturing Message Specification (MMS) at the upper (application) layer for transfer
of real-time data. This protocol has been in existence for several of years and provides a set of services suitable for the
transfer of data within a substation LAN environment. Actual MMS protocol services are mapped to IEC 61850 abstract ser-
vices in IEC 61850-8-1.
The D60 relay supports IEC 61850 server services over TCP/IP. The TCP/IP profile requires the D60 to have an IP address
to establish communications. These addresses are located in the SETTINGS  PRODUCT SETUP  COMMUNICATIONS 
NETWORK menu. It is possible to have up to five simultaneous connections (in addition to DNP and Modbus/TCP (non-IEC
61850) connections).
• Client/server: This is a connection-oriented type of communication. The connection is initiated by the client, and com-
munication activity is controlled by the client. IEC 61850 clients are often substation computers running HMI programs
or SOE logging software. Servers are usually substation equipment such as protection relays, meters, RTUs, trans-
former tap changers, or bay controllers.
• Peer-to-peer: This is a non-connection-oriented, high speed type of communication usually between substation equip-
ment such as protection relays. GSSE and GOOSE are methods of peer-to-peer communication.
• Substation configuration language (SCL): A substation configuration language is a number of files used to describe
the configuration of substation equipment. Each configured device has an IEC Capability Description (ICD) file. The
substation single line information is stored in a System Specification Description (SSD) file. The entire substation con-
figuration is stored in a Substation Configuration Description (SCD) file. The SCD file is the combination of the individ-
ual ICD files and the SSD file.
GE Multilin D60 Line Distance Protection System C-1

C.2 SERVER DATA ORGANIZATION APPENDIX C
C.2SERVER DATA ORGANIZATION C.2.1 OVERVIEW
IEC 61850 defines an object-oriented approach to data and services. An IEC 61850 physical device can contain one or
more logical device(s). Each logical device can contain many logical nodes. Each logical node can contain many data
objects. Each data object is composed of data attributes and data attribute components. Services are available at each
level for performing various functions, such as reading, writing, control commands, and reporting.
Each D60 IED represents one IEC 61850 physical device. The physical device contains one logical device, and the logical
device contains many logical nodes. The logical node LPHD1 contains information about the D60 IED physical device. The
logical node LLN0 contains information about the D60 IED logical device.
C.2.2 GGIO1: DIGITAL STATUS VALUES
C The GGIO1 logical node is available in the D60 to provide access to as many 128 digital status points and associated time-
stamps and quality flags. The data content must be configured before the data can be used. GGIO1 provides digital status
points for access by clients.
It is intended that clients use GGIO1 in order to access digital status values from the D60. Configuration settings are pro-
vided to allow the selection of the number of digital status indications available in GGIO1 (8 to 128), and to allow the choice
of the D60 FlexLogic operands that drive the status of the GGIO1 status indications. Clients can utilize the IEC 61850 buff-
ered and unbuffered reporting features available from GGIO1 in order to build sequence of events (SOE) logs and HMI dis-
play screens. Buffered reporting should generally be used for SOE logs since the buffering capability reduces the chances
of missing data state changes. Unbuffered reporting should generally be used for local status display.
C.2.3 GGIO2: DIGITAL CONTROL VALUES
The GGIO2 logical node is available to provide access to the D60 virtual inputs. Virtual inputs are single-point control
(binary) values that can be written by clients. They are generally used as control inputs. GGIO2 provides access to the vir-
tual inputs through the IEC 61850 standard control model (ctlModel) services:
• Status only.
• Direct control with normal security.
• SBO control with normal security.
Configuration settings are available to select the control model for each point. Each virtual input used through GGIO2
should have its VIRTUAL INPUT 1(64) FUNCTION setting programmed as “Enabled” and its corresponding GGIO2 CF SPSCO1(64)
CTLMODEL setting programmed to the appropriate control configuration.
C.2.4 GGIO3: DIGITAL STATUS AND ANALOG VALUES FROM GOOSE DATA
The GGIO3 logical node is available to provide access for clients to values received via configurable GOOSE messages.
The values of the digital status indications and analog values in GGIO3 originate in GOOSE messages sent from other
devices.
C.2.5 GGIO4: GENERIC ANALOG MEASURED VALUES
The GGIO4 logical node provides access to as many as 32 analog value points, as well as associated timestamps and
quality flags. The data content must be configured before the data can be used. GGIO4 provides analog values for access
by clients.
It is intended that clients use GGIO4 to access generic analog values from the D60. Configuration settings allow the selec-
tion of the number of analog values available in GGIO4 (4 to 32) and the choice of the FlexAnalog values that determine
the value of the GGIO4 analog inputs. Clients can utilize polling or the IEC 61850 unbuffered reporting feature available
from GGIO4 in order to obtain the analog values provided by GGIO4.
C-2 D60 Line Distance Protection System GE Multilin

APPENDIX C C.2 SERVER DATA ORGANIZATION
C.2.6 MMXU: ANALOG MEASURED VALUES
A limited number of measured analog values are available through the MMXU logical nodes.
Each MMXU logical node provides data from a D60 current and voltage source. There is one MMXU available for each
configurable source (programmed in the SETTINGS  SYSTEM SETUP  SIGNAL SOURCES menu). MMXU1 provides data
from D60 source 1, and MMXU2 provides data from D60 source 2.
MMXU data is provided in two forms: instantaneous and deadband. The instantaneous values are updated every time a
read operation is performed by a client. The deadband values are calculated as described in IEC 61850 parts 7-1 and 7-3.
The selection of appropriate deadband settings for the D60 is described in chapter 5 of this manual.
IEC 61850 buffered and unbuffered reporting capability is available in all MMXU logical nodes. MMXUx logical nodes pro-
vide the following data for each source:
•
•
MMXU1.MX.TotW: three-phase real power
MMXU1.MX.TotVAr: three-phase reactive power
C
• MMXU1.MX.TotVA: three-phase apparent power
• MMXU1.MX.TotPF: three-phase power factor
• MMXU1.MX.Hz: frequency
• MMXU1.MX.PPV.phsAB: phase AB voltage magnitude and angle
• MMXU1.MX.PPV.phsBC: phase BC voltage magnitude and angle
• MMXU1.MX.PPV.phsCA: Phase CA voltage magnitude and angle
• MMXU1.MX.PhV.phsA: phase AG voltage magnitude and angle
• MMXU1.MX.PhV.phsB: phase BG voltage magnitude and angle
• MMXU1.MX.PhV.phsC: phase CG voltage magnitude and angle
• MMXU1.MX.A.phsA: phase A current magnitude and angle
• MMXU1.MX.A.phsB: phase B current magnitude and angle
• MMXU1.MX.A.phsC: phase C current magnitude and angle
• MMXU1.MX.A.neut: ground current magnitude and angle
• MMXU1.MX.W.phsA: phase A real power
• MMXU1.MX.W.phsB: phase B real power
• MMXU1.MX.W.phsC: phase C real power
• MMXU1.MX.VAr.phsA: phase A reactive power
• MMXU1.MX.VAr.phsB: phase B reactive power
• MMXU1.MX.VAr.phsC: phase C reactive power
• MMXU1.MX.VA.phsA: phase A apparent power
• MMXU1.MX.VA.phsB: phase B apparent power
• MMXU1.MX.VA.phsC: phase C apparent power
• MMXU1.MX.PF.phsA: phase A power factor
• MMXU1.MX.PF.phsB: phase B power factor
• MMXU1.MX.PF.phsC: phase C power factor
C.2.7 PROTECTION AND OTHER LOGICAL NODES
The following list describes the protection elements for all UR-series relays. The D60 relay will contain a subset of protec-
tion elements from this list.
• PDIF: bus differential, transformer instantaneous differential, transformer percent differential, current differential

C.2 SERVER DATA ORGANIZATION APPENDIX C
• PDIS: phase distance, ground distance

• PIOC: phase instantaneous overcurrent, neutral instantaneous overcurrent, ground instantaneous overcurrent, nega-
tive-sequence instantaneous overcurrent.
• PTOC: phase time overcurrent, neutral time overcurrent, ground time overcurrent, negative-sequence time overcur-
rent, neutral directional overcurrent, negative-sequence directional overcurrent
• PTUV: phase undervoltage, auxiliary undervoltage, third harmonic neutral undervoltage
• PTOV: phase overvoltage, neutral overvoltage, auxiliary overvoltage, negative sequence overvoltage
• RBRF: breaker failure
• RREC: autoreclosure
• RPSB: power swing detection
C • RFLO: fault locator

• XCBR: breaker control
• XSWI: circuit switch
• CSWI: switch controller
The protection elements listed above contain start (pickup) and operate flags. For example, the start flag for PIOC1 is
PIOC1.ST.Str.general. The operate flag for PIOC1 is PIOC1.ST.Op.general. For the D60 protection elements, these flags
take their values from the pickup and operate FlexLogic operands for the corresponding element.
Some protection elements listed above contain directional start values. For example, the directional start value for PDIS1 is
PDIS1.ST.Str.dirGeneral. This value is built from the directional FlexLogic operands for the element.
The RFLO logical node contains the measurement of the distance to fault calculation in kilometers. This value originates in
the fault locator function.
The XCBR logical node is directly associated with the breaker control feature.
• XCBR1.ST.Loc: This is the state of the XCBR1 local/remote switch. A setting is provided to assign a FlexLogic operand
to determine the state. When local mode is true, IEC 61850 client commands will be rejected.
• XCBR1.ST.Opcnt: This is an operation counter as defined in IEC 61850. Command settings are provided to allow the
counter to be cleared.
• XCBR1.ST.Pos: This is the position of the breaker. The breaker control FlexLogic operands are used to determine this
state.
– Intermediate state (00) is indicated when the BREAKER 1 OPEN and BREAKER 1 CLOSED operands are both On.
– Off state (01) is indicated when the BREAKER 1 OPEN operand is On.
– On state (10) is indicated when the BREAKER 1 CLOSED operand is On.
– Bad state (11) is indicated when the BREAKER 1 OPEN and BREAKER 1 CLOSED operands are Off.
• XCBR1.ST.BlkOpn: This is the state of the block open command logic. When true, breaker open commands from IEC
61850 clients will be rejected.
• XCBR1.ST.BlkCls: This is the state of the block close command logic. When true, breaker close commands from IEC
61850 clients will be rejected.
• XCBR1.CO.Pos: This is where IEC 61850 clients can issue open or close commands to the breaker. SBO control with
normal security is the only supported IEC 61850 control model.
• XCBR1.CO.BlkOpn: This is where IEC 61850 clients can issue block open commands to the breaker. Direct control
with normal security is the only supported IEC 61850 control model.
• XCBR1.CO.BlkCls: This is where IEC 61850 clients can issue block close commands to the breaker. Direct control
with normal security is the only supported IEC 61850 control model.

APPENDIX C C.3 SERVER FEATURES AND CONFIGURATION
C.3SERVER FEATURES AND CONFIGURATION C.3.1 BUFFERED/UNBUFFERED REPORTING
IEC 61850 buffered and unbuffered reporting is provided in the GGIO1 logical nodes (for binary status values) and MMXU1
to MMXU6 (for analog measured values). Report settings can be configured using the EnerVista UR Setup software, sub-
station configurator software, or via an IEC 61850 client. The following items can be configured:
• TrgOps: Trigger options. The following bits are supported by the D60:
– Bit 1: data-change
– Bit 4: integrity
– Bit 5: general interrogation
• OptFlds: Option Fields. The following bits are supported by the D60:
–
–
Bit 1: sequence-number
Bit 2: report-time-stamp
C
– Bit 3: reason-for-inclusion
– Bit 4: data-set-name
– Bit 5: data-reference
– Bit 6: buffer-overflow (for buffered reports only)
– Bit 7: entryID (for buffered reports only)
– Bit 8: conf-revision
– Bit 9: segmentation
• IntgPd: Integrity period.
• BufTm: Buffer time.
C.3.2 FILE TRANSFER
MMS file services are supported to allow transfer of oscillography, event record, or other files from a D60 relay.
C.3.3 TIMESTAMPS AND SCANNING
The timestamp values associated with all IEC 61850 data items represent the time of the last change of either the value or
quality flags of the data item. To accomplish this functionality, all IEC 61850 data items must be regularly scanned for data
changes, and the timestamp updated when a change is detected, regardless of the connection status of any IEC 61850 cli-
ents. For applications where there is no IEC 61850 client in use, the IEC 61850 SERVER SCANNING setting can be pro-
grammed as “Disabled”. If a client is in use, this setting should be programmed as “Enabled” to ensure the proper
generation of IEC 61850 timestamps.
C.3.4 LOGICAL DEVICE NAME
The logical device name is used to identify the IEC 61850 logical device that exists within the D60. This name is composed
of two parts: the IED name setting and the logical device instance. The complete logical device name is the combination of
the two character strings programmed in the IEDNAME and LD INST settings. The default values for these strings are “IED-
Name” and “LDInst”. These values should be changed to reflect a logical naming convention for all IEC 61850 logical
devices in the system.
C.3.5 LOCATION
The LPHD1 logical node contains a data attribute called location (LPHD1.DC.PhyNam.location). This is a character string
meant to describe the physical location of the D60. This attribute is programmed through the LOCATION setting and its
default value is “Location”. This value should be changed to describe the actual physical location of the D60.

C.3 SERVER FEATURES AND CONFIGURATION APPENDIX C
C.3.6 LOGICAL NODE NAME PREFIXES
IEC 61850 specifies that each logical node can have a name with a total length of 11 characters. The name is composed of:
• A five or six-character name prefix.
• A four-character standard name (for example, MMXU, GGIO, PIOC, etc.).
• A one or two-character instantiation index.
Complete names are of the form xxxxxxPIOC1, where the xxxxxx character string is configurable. Details regarding the
logical node naming rules are given in IEC 61850 parts 6 and 7-2. It is recommended that a consistent naming convention
be used for an entire substation project.
C.3.7 CONNECTION TIMING
C A built-in TCP/IP connection timeout of two minutes is employed by the D60 to detect ‘dead’ connections. If there is no data
traffic on a TCP connection for greater than two minutes, the connection will be aborted by the D60. This frees up the con-
nection to be used by other clients. Therefore, when using IEC 61850 reporting, clients should configure report control
block items such that an integrity report will be issued at least every 2 minutes (120000 ms). This ensures that the D60 will
not abort the connection. If other MMS data is being polled on the same connection at least once every 2 minutes, this
timeout will not apply.
C.3.8 NON-IEC 61850 DATA
The D60 relay makes available a number of non-IEC 61850 data items. These data items can be accessed through the
“UR” MMS domain. IEC 61850 data can be accessed through the standard IEC 61850 logical device. To access the non-
IEC data items, the INCLUDE NON-IEC DATA setting must be “Enabled”.
C.3.9 COMMUNICATION SOFTWARE UTILITIES
The exact structure and values of the supported IEC 61850 logical nodes can be seen by connecting to a D60 relay with an
MMS browser, such as the “MMS Object Explorer and AXS4-MMS” DDE/OPC server from Sisco Inc.

APPENDIX C C.4 GENERIC SUBSTATION EVENT SERVICES: GSSE AND GOOSE
C.4GENERIC SUBSTATION EVENT SERVICES: GSSE AND GOOSE C.4.1 OVERVIEW
IEC 61850 specifies two types of peer-to-peer data transfer services: Generic Substation State Events (GSSE) and Generic
Object Oriented Substation Events (GOOSE). GSSE services are compatible with UCA 2.0 GOOSE. IEC 61850 GOOSE
services provide virtual LAN (VLAN) support, Ethernet priority tagging, and Ethertype Application ID configuration. The sup-
port for VLANs and priority tagging allows for the optimization of Ethernet network traffic. GOOSE messages can be given
a higher priority than standard Ethernet traffic, and they can be separated onto specific VLANs. Because of the additional
features of GOOSE services versus GSSE services, it is recommended that GOOSE be used wherever backwards com-
patibility with GSSE (or UCA 2.0 GOOSE) is not required.
Devices that transmit GSSE and/or GOOSE messages also function as servers. Each GSSE publisher contains a “GSSE
control block” to configure and control the transmission. Each GOOSE publisher contains a “GOOSE control block” to con-
figure and control the transmission. The transmission is also controlled via device settings. These settings can be seen in
the ICD and/or SCD files, or in the device configuration software or files.
IEC 61850 recommends a default priority value of 4 for GOOSE. Ethernet traffic that does not contain a priority tag has a
C
default priority of 1. More details are specified in IEC 61850 part 8-1.
IEC 61850 recommends that the Ethertype Application ID number be configured according to the GOOSE source. In the
D60, the transmitted GOOSE Application ID number must match the configured receive Application ID number in the
receiver. A common number may be used for all GOOSE transmitters in a system. More details are specified in IEC 61850
part 8-1.
C.4.2 GSSE CONFIGURATION
IEC 61850 Generic Substation Status Event (GSSE) communication is compatible with UCA GOOSE communication.
GSSE messages contain a number of double point status data items. These items are transmitted in two pre-defined data
structures named DNA and UserSt. Each DNA and UserSt item is referred to as a ‘bit pair’. GSSE messages are transmit-
ted in response to state changes in any of the data points contained in the message. GSSE messages always contain the
same number of DNA and UserSt bit pairs. Depending the on the configuration, only some of these bit pairs may have val-
ues that are of interest to receiving devices.
The GSSE FUNCTION, GSSE ID, and GSSE DESTINATION MAC ADDRESS settings are used to configure GSSE transmission.
GSSE FUNCTION is set to “Enabled” to enable the transmission. If a valid multicast Ethernet MAC address is entered for the
GSSE DESTINATION MAC ADDRESS setting, this address will be used as the destination MAC address for GSSE messages. If
a valid multicast Ethernet MAC address is not entered (for example, 00 00 00 00 00 00), the D60 will use the source Ether-
net MAC address as the destination, with the multicast bit set.
C.4.3 FIXED GOOSE
The D60 supports two types of IEC 61850 Generic Object Oriented Substation Event (GOOSE) communication: fixed
GOOSE and configurable GOOSE. All GOOSE messages contain IEC 61850 data collected into a dataset. It is this dataset
that is transferred using GOOSE message services. The dataset transferred using the D60 fixed GOOSE is the same data
that is transferred using the GSSE feature; that is, the DNA and UserSt bit pairs. The FlexLogic operands that determine
the state of the DNA and UserSt bit pairs are configurable via settings, but the fixed GOOSE dataset always contains the
same DNA/UserSt data structure. Upgrading from GSSE to GOOSE services is simply a matter of enabling fixed GOOSE
and disabling GSSE. The remote inputs and outputs are configured in the same manner for both GSSE and fixed GOOSE.
It is recommended that the fixed GOOSE be used for implementations that require GOOSE data transfer between UR-
series IEDs. Configurable GOOSE may be used for implementations that require GOOSE data transfer between UR-series
IEDs and devices from other manufacturers.
C.4.4 CONFIGURABLE GOOSE
The configurable GOOSE feature allows for the configuration of the datasets to be transmitted or received from the D60.
The D60 supports the configuration of eight (8) transmission and reception datasets, allowing for the optimization of data
transfer between devices.

C.4 GENERIC SUBSTATION EVENT SERVICES: GSSE AND GOOSE APPENDIX C
Items programmed for dataset 1 and 2 will have changes in their status transmitted as soon as the change is detected.
Dataset 1 should be used for high-speed transmission of data that is required for applications such as transfer tripping,
blocking, and breaker fail initiate. At least one digital status value needs to be configured in dataset 1 to enable transmis-
sion of all data configured for dataset 1. Configuring analog data only to dataset 1 will not activate transmission.
Items programmed for datasets 3 through 8 will have changes in their status transmitted at a maximum rate of every
100 ms. Datasets 3 through 8 will regularly analyze each data item configured within them every 100 ms to identify if any
changes have been made. If any changes in the data items are detected, these changes will be transmitted through a
GOOSE message. If there are no changes detected during this 100 ms period, no GOOSE message will be sent.
For all datasets 1 through 8, the integrity GOOSE message will still continue to be sent at the pre-configured rate even if no
changes in the data items are detected.
The GOOSE functionality was enhanced to prevent the relay from flooding a communications network with GOOSE mes-
sages due to an oscillation being created that is triggering a message.
C The D60 has the ability of detecting if a data item in one of the GOOSE datasets is erroneously oscillating. This can be
caused by events such as errors in logic programming, inputs improperly being asserted and de-asserted, or failed station
components. If erroneously oscillation is detected, the D60 will stop sending GOOSE messages from the dataset for a min-
imum period of one second. Should the oscillation persist after the one second time-out period, the D60 will continue to
block transmission of the dataset. The D60 will assert the MAINTENANCE ALERT: GGIO Ind XXX oscill self-test error mes-
sage on the front panel display, where XXX denotes the data item detected as oscillating.
The configurable GOOSE feature is recommended for applications that require GOOSE data transfer between UR-series
IEDs and devices from other manufacturers. Fixed GOOSE is recommended for applications that require GOOSE data
transfer between UR-series IEDs.
IEC 61850 GOOSE messaging contains a number of configurable parameters, all of which must be correct to achieve the
successful transfer of data. It is critical that the configured datasets at the transmission and reception devices are an exact
match in terms of data structure, and that the GOOSE addresses and name strings match exactly. Manual configuration is
possible, but third-party substation configuration software may be used to automate the process. The EnerVista UR Set-
upsoftware can produce IEC 61850 ICD files and import IEC 61850 SCD files produced by a substation configurator (refer
to the IEC 61850 IED configuration section later in this appendix).
Use independent ports for IEC 61850 communication and take care when configuring the settings,
else loss of protection or misoperation of the relay can result.
The following example illustrates the configuration required to transfer IEC 61850 data items between two devices. The
general steps required for transmission configuration are:
1. Configure the transmission dataset.
The general steps required for reception configuration are:
1. Configure the reception dataset.
This example shows how to configure the transmission and reception of three IEC 61850 data items: a single point status
value, its associated quality flags, and a floating point analog value.
The following procedure illustrates the transmission configuration.
1. Configure the transmission dataset by making the following changes in the PRODUCT SETUP  COMMUNICATION 
IEC 61850 PROTOCOL  GSSE/GOOSE CONFIGURATION  TRANSMISSION  CONFIGURABLE GOOSE  CONFIGURABLE
GOOSE 1  CONFIG GSE 1 DATASET ITEMS settings menu:
The transmission dataset now contains a set of quality flags and a single point status Boolean value. The reception
dataset on the receiving device must exactly match this structure.

APPENDIX C C.4 GENERIC SUBSTATION EVENT SERVICES: GSSE AND GOOSE
2. Configure the GOOSE service settings by making the following changes in the PRODUCT SETUP  COMMUNICATION
 IEC 61850 PROTOCOL  GSSE/GOOSE CONFIGURATION  TRANSMISSION  CONFIGURABLE GOOSE  CONFIGU-
RABLE GOOSE 1 settings menu:
– Set CONFIG GSE 1 FUNCTION to “Enabled”.

– Set CONFIG GSE 1 ID to an appropriate descriptive string (the default value is “GOOSEOut_1”).
– Set CONFIG GSE 1 DST MAC to a multicast address (for example, 01 00 00 12 34 56).
– Set the CONFIG GSE 1 VLAN PRIORITY; the default value of “4” is OK for this example.
– Set the CONFIG GSE 1 VLAN ID value; the default value is “0”, but some switches may require this value to be “1”.
– Set the CONFIG GSE 1 ETYPE APPID value. This setting represents the Ethertype application ID and must match the
configuration on the receiver (the default value is “0”).
– Set the CONFIG GSE 1 CONFREV value. This value changes automatically as described in IEC 61850 part 7-2. For
this example it can be left at its default value. C
3. Configure the data by making the following changes in the PRODUCT SETUP  COMMUNICATION  IEC 61850 PROTO-
COL  GGIO1 STATUS CONFIGURATION settings menu:
– Set GGIO1 INDICATION 1 to a FlexLogic operand used to provide the status of GGIO1.ST.Ind1.stVal (for example, a
contact input, virtual input, a protection element status, etc.).
The D60 must be rebooted (control power removed and re-applied) before these settings take effect.
The following procedure illustrates the reception configuration.
1. Configure the reception dataset by making the following changes in the PRODUCT SETUP  COMMUNICATION  IEC
61850 PROTOCOL  GSSE/GOOSE CONFIGURATION  RECEPTION  CONFIGURABLE GOOSE  CONFIGURABLE GOOSE
1  CONFIG GSE 1 DATASET ITEMS settings menu:
The reception dataset now contains a set of quality flags, a single point status Boolean value, and a floating point ana-
log value. This matches the transmission dataset configuration above.
2. Configure the GOOSE service settings by making the following changes in the INPUTS/OUTPUTS  REMOTE DEVICES
 REMOTE DEVICE 1 settings menu:
– Set REMOTE DEVICE 1 ID to match the GOOSE ID string for the transmitting device. Enter “GOOSEOut_1”.
– Set REMOTE DEVICE 1 ETYPE APPID to match the Ethertype application ID from the transmitting device. This is “0” in
the example above.
– Set the REMOTE DEVICE 1 DATASET value. This value represents the dataset number in use. Since we are using
configurable GOOSE 1 in this example, program this value as “GOOSEIn 1”.
3. Configure the data by making the following changes in the INPUTS/OUTPUTS  REMOTE INPUTS  REMOTE INPUT 1
settings menu:
– Set REMOTE IN 1 DEVICE to “GOOSEOut_1”.
– Set REMOTE IN 1 ITEM to “Dataset Item 2”. This assigns the value of the GGIO3.ST.Ind1.stVal single point status
item to remote input 1.
Remote input 1 can now be used in FlexLogic equations or other settings. The D60 must be rebooted (control power
removed and re-applied) before these settings take effect.
The value of remote input 1 (Boolean on or off) in the receiving device will be determined by the GGIO1.ST.Ind1.stVal value
in the sending device. The above settings will be automatically populated by the EnerVista UR Setup software when a com-
plete SCD file is created by third party substation configurator software.

C.4 GENERIC SUBSTATION EVENT SERVICES: GSSE AND GOOSE APPENDIX C
C.4.5 ETHERNET MAC ADDRESS FOR GSSE/GOOSE
Ethernet capable devices each contain a unique identifying address called a Media Access Control (MAC) address. This
address cannot be changed and is unique for each Ethernet device produced worldwide. The address is six bytes in length
and is usually represented as six hexadecimal values (for example, 00 A0 F4 01 02 03). It is used in all Ethernet frames as
the ‘source’ address of the frame. Each Ethernet frame also contains a destination address. The destination address can
be different for each Ethernet frame depending on the intended destination of the frame.
A special type of destination address called a multicast address is used when the Ethernet frame can be received by more
than one device. An Ethernet MAC address is multicast when the least significant bit of the first byte is set (for example, 01
00 00 00 00 00 is a multicast address).
GSSE and GOOSE messages must have multicast destination MAC addresses.
By default, the D60 is configured to use an automated multicast MAC scheme. If the D60 destination MAC address setting
C is not a valid multicast address (that is, the least significant bit of the first byte is not set), the address used as the destina-
tion MAC will be the same as the local MAC address, but with the multicast bit set. Thus, if the local MAC address is 00 A0
F4 01 02 03, then the destination MAC address will be 01 A0 F4 01 02 03.
C.4.6 GSSE ID AND GOOSE ID SETTINGS
GSSE messages contain an identifier string used by receiving devices to identify the sender of the message, defined in IEC
61850 part 8-1 as GsID. This is a programmable 65-character string. This string should be chosen to provide a descriptive
name of the originator of the GSSE message.
GOOSE messages contain an identifier string used by receiving devices to identify the sender of the message, defined in
IEC 61850 part 8-1 as GoID. This programmable 65-character string should be a descriptive name of the originator of the
GOOSE message. GOOSE messages also contain two additional character strings used for identification of the message:
DatSet - the name of the associated dataset, and GoCBRef - the reference (name) of the associated GOOSE control block.
These strings are automatically populated and interpreted by the D60; no settings are required.

APPENDIX C C.5 IEC 61850 IMPLEMENTATION VIA ENERVISTA UR SETUP
C.5IEC 61850 IMPLEMENTATION VIA ENERVISTA UR SETUP C.5.1 OVERVIEW
The D60 can be configured for IEC 61850 via the EnerVista UR Setup software as follows.
1. An ICD file is generated for the D60 by the EnerVista UR Setup software that describe the capabilities of the IED.
2. The ICD file is then imported into a system configurator along with other ICD files for other IEDs (from GE or other ven-
dors) for system configuration.
3. The result is saved to a SCD file, which is then imported back to EnerVista UR Setup to create one or more settings
file(s). The settings file(s) can then be used to update the relay(s) with the new configuration information.
The configuration process is illustrated below.
Figure C–1: IED CONFIGURATION PROCESS

The following acronyms and abbreviations are used in the procedures describing the IED configuration process for IEC
61850:
• BDA: Basic Data Attribute, that is not structured
• DAI: Instantiated Data Attribute
• DO: Data Object type or instance, depending on the context

C.5 IEC 61850 IMPLEMENTATION VIA ENERVISTA UR SETUP APPENDIX C
• DOI: Instantiated Data Object

• IED: Intelligent Electronic Device
• LDInst: Instantiated Logical Device
• LNInst: Instantiated Logical Node
• SCL: Substation Configuration Description Language. The configuration language is an application of the Extensible
Markup Language (XML) version 1.0.
• SDI: Instantiated Sub DATA; middle name part of a structured DATA name
• UR: GE Multilin Universal Relay series
• URI: Universal Resource Identifier
• URS: UR-series relay setting file
C • XML: Extensible Markup Language
The following SCL variants are also used:
• ICD: IED Capability Description
• CID: Configured IED Description
• SSD: System Specification Description
• SCD: Substation Configuration Description
The following IEC related tools are referenced in the procedures that describe the IED configuration process for IEC 61850:
• System configurator or Substation configurator: This is an IED independent system level tool that can import or
export configuration files defined by IEC 61850-6. It can import configuration files (ICD) from several IEDs for system
level engineering and is used to add system information shared by different IEDs. The system configuration generates
a substation related configuration file (SCD) which is fed back to the IED configurator (for example, EnerVista UR
Setup) for system related IED configuration. The system configurator should also be able to read a system specifica-
tion file (SSD) to use as base for starting system engineering, or to compare it with an engineered system for the same
substation.
• IED configurator: This is a vendor specific tool that can directly or indirectly generate an ICD file from the IED (for
example, from a settings file). It can also import a system SCL file (SCD) to set communication configuration parame-
ters (that is, required addresses, reception GOOSE datasets, IDs of incoming GOOSE datasets, etc.) for the IED. The
IED configurator functionality is implemented in the GE Multilin EnerVista UR Setup software.
C.5.2 CONFIGURING IEC 61850 SETTINGS
Before creating an ICD file, the user can customize the IEC 61850 related settings for the IED. For example, the IED name
and logical device instance can be specified to uniquely identify the IED within the substation, or transmission GOOSE
datasets created so that the system configurator can configure the cross-communication links to send GOOSE messages
from the IED. Once the IEC 61850 settings are configured, the ICD creation process will recognize the changes and gener-
ate an ICD file that contains the updated settings.
Some of the IED settings will be modified during they system configuration process. For example, a new IP address may be
assigned, line items in a Transmission GOOSE dataset may be added or deleted, or prefixes of some logical nodes may be
changed. While all new configurations will be mapped to the D60 settings file when importing an SCD file, all unchanged
settings will preserve the same values in the new settings file.
These settings can be configured either directly through the relay panel or through the EnerVista UR Setup software (pre-
ferred method). The full list of IEC 61850 related settings for are as follows:
• Network configuration: IP address, IP subnet mask, and default gateway IP address (access through the Settings >
Product Setup > Communications > Network menu tree in EnerVista UR Setup).
• Server configuration: IED name and logical device instance (access through the Settings > Product Setup > Com-
munications > IEC 61850 > Server Configuration menu tree in EnerVista UR Setup).
• Logical node prefixes, which includes prefixes for all logical nodes except LLN0 (access through the Settings > Prod-
uct Setup > Communications > IEC 61850 > Logical Node Prefixes menu tree in EnerVista UR Setup).

• MMXU deadbands, which includes deadbands for all available MMXUs. The number of MMXUs is related to the num-
ber of CT/VT modules in the relay. There are two MMXUs for each CT/VT module. For example, if a relay contains two
CT/VT modules, there will be four MMXUs available (access through the Settings > Product Setup > Communica-
tions > IEC 61850 > MMXU Deadbands menu tree in EnerVista UR Setup).
• GGIO1 status configuration, which includes the number of status points in GGIO1 as well as the potential internal map-
pings for each GGIO1 indication. However only the number of status points will be used in the ICD creation process
(access through the Settings > Product Setup > Communications > IEC 61850 > GGIO1 Status Configuration
menu tree in EnerVista UR Setup).
• GGIO2 control configuration, which includes ctlModels for all SPCSOs within GGIO2 (access through the Settings >
Product Setup > Communications > IEC 61850 > GGIO2 Control Configuration menu tree in EnerVista UR
Setup).
• Configurable transmission GOOSE, which includes eight configurable datasets that can be used for GOOSE transmis-
sion. The GOOSE ID can be specified for each dataset (it must be unique within the IED as well as across the whole
substation), as well as the destination MAC address, VLAN priority, VLAN ID, ETYPE APPID, and the dataset items.
C
The selection of the dataset item is restricted by firmware version; for version 7.1x, only GGIO1.ST.Indx.stVal and
GGIO1.ST.Indx.q are valid selection (where x is between 1 to N, and N is determined by number of GGIO1 status
points). Although configurable transmission GOOSE can also be created and altered by some third-party system con-
figurators, we recommend configuring transmission GOOSE for GE Multilin IEDs before creating the ICD, and strictly
within EnerVista UR Setup software or the front panel display (access through the Settings > Product Setup > Com-
munications > IEC 61850 > GSSE/GOOSE Configuration > Transmission > Tx Configurable GOOSE menu tree
in EnerVista UR Setup).
• Configurable reception GOOSE, which includes eight configurable datasets that can be used for GOOSE reception.
However, unlike datasets for transmission, datasets for reception only contains dataset items, and they are usually cre-
ated automatically by process of importing the SCD file (access through the Settings > Product Setup > Communi-
cations > IEC 61850 > GSSE/GOOSE Configuration > Reception > Rx Configurable GOOSE menu tree in
EnerVista UR Setup).
• Remote devices configuration, which includes remote device ID (GOOSE ID or GoID of the incoming transmission
GOOSE dataset), ETYPE APPID (of the GSE communication block for the incoming transmission GOOSE), and
DATASET (which is the name of the associated reception GOOSE dataset). These settings are usually done automat-
ically by process of importing SCD file (access through the Settings > Inputs/Outputs > Remote Devices menu tree
in EnerVista UR Setup).
• Remote inputs configuration, which includes device (remote device ID) and item (which dataset item in the associated
reception GOOSE dataset to map) values. Only the items with cross-communication link created in SCD file should be
mapped. These configurations are usually done automatically by process of importing SCD file (access through the
Settings > Inputs/Outputs > Remote Inputs menu tree in EnerVista UR Setup).
C.5.3 ABOUT ICD FILES
The SCL language is based on XML, and its syntax definition is described as a W3C XML Schema. ICD is one type of SCL
file (which also includes SSD, CID and SCD files). The ICD file describes the capabilities of an IED and consists of four
major sections:
• Header
• Communication
• IEDs
• DataTypeTemplates

The root file structure of an ICD file is illustrated below.
SCL
Header (id, version, revision, toolID, nameStructure)
Communication
IED (name, type, manufacture, configVersion)
DataTypeTemplates
842795A1.CDR
Figure C–2: ICD FILE STRUCTURE, SCL (ROOT) NODE

The Header node identifies the ICD file and its version, and specifies options for the mapping of names to signals
C The Communication node describes the direct communication connection possibilities between logical nodes by means of
logical buses (sub-networks) and IED access ports. The communication section is structured as follows.
Communication
SubNetwork (name)
ConnectedAP (iedName, apName)
Address
P (type)
Text
Other P elements
GSE (IdInst, cbName)
Address
P (type)
Text
Other GSE elements Other P elements

842796A1.CDR
Figure C–3: ICD FILE STRUCTURE, COMMUNICATIONS NODE

The SubNetwork node contains all access points which can (logically) communicate with the sub-network protocol and
without the intervening router. The ConnectedAP node describes the IED access point connected to this sub-network. The
Address node contains the address parameters of the access point. The GSE node provides the address element for stat-
ing the control block related address parameters, where IdInst is the instance identification of the logical device within the
IED on which the control block is located, and cbName is the name of the control block.
The IED node describes the (pre-)configuration of an IED: its access points, the logical devices, and logical nodes instanti-
ated on it. Furthermore, it defines the capabilities of an IED in terms of communication services offered and, together with
its LNType, instantiated data (DO) and its default or configuration values. There should be only one IED section in an ICD
since it only describes one IED.

IED (name, type, manufacture, configVersion)
Services
DynAssoication GetDataSetValue ReadWrite ConfLogControl (max)
GetDirectory SetDataSetValue TimerActivatedControl GSEDir
GetDateObjectDefinition DataSetDirectory ConfReportControl (max) GOOSE (max)
DataObjectDirectory ConfDataSet (max, maxAttributes) GetCBValues GSSE (max)
AccessPoint (name)
Server
Authentication (none) C
LDevice (inst)
LN0 (InType, InClass, inst)
DataSet (name)
FCDA (fc, doName, daName, IdInst, prefix, InClass, InInst)
Other FCDA elements
Other DataSet elements
ReportControl (name, datSet, intgPd, rptID, confRev, buffered)
TrgOps (dchg) OptFields (seqNum) RptEnabled
Other ReportControl elements
DOI (name)
SDI (name) DAI (name)

Val Text
Other DOI elements SDI (name)

DAI (name)
GSEControl (name, datSet, type, confRev, appID) Val Text
Other GSEControl elements
LN (InType, InClass, prefix, inst)
DataSet (name)
FCDA (IdInst, prefix, InClass, InInst, doName, fc)
Other FCDA elements
Other DataSet elements
ReportControl (name, datSet, intgPd, rptID, confRev, buffered)
TrgOps (dchg) OptFields (seqNum) RptEnabled
Other ReportControl elements
DOI (name)
SDI (name) DAI (name)

Val Text
Other DOI elements SDI (name)

DAI (name)
Val Text
Other LN elements
Other LDevice elements

842797A1.CDR
Figure C–4: ICD FILE STRUCTURE, IED NODE

The DataTypeTemplates node defines instantiable logical node types. A logical node type is an instantiable template of the
data of a logical node. A LnodeType is referenced each time that this instantiable type is needed with an IED. A logical
node type template is built from DATA (DO) elements, which again have a DO type, which is derived from the DATA classes
(CDC). DOs consist of attributes (DA) or of elements of already defined DO types (SDO). The attribute (DA) has a func-
tional constraint, and can either have a basic type, be an enumeration, or a structure of a DAType. The DAType is built from
BDA elements, defining the structure elements, which again can be BDA elements of have a base type such as DA.
DataTypeTemplates
LNodeType (id, InClass)
DO (name, type)
Other DO elements
C Other LNodeType elements
DOType (id, cdc)
SDO (name, type) DA (name, fc, bType, type) Val Text
Other SDO elements Other DA elements
Other DOType elements
DAType (id)
BDA (name, bType, type)
Other BDA elements
Other DAType elements
EnumType (id)
EnumVal (ord) Text
Other EnumVal elements
Other EnumType elements

842798A1.CDR
Figure C–5: ICD FILE STRUCTURE, DATATYPETEMPLATES NODE

C.5.4 CREATING AN ICD FILE WITH ENERVISTA UR SETUP
An ICD file can be created directly from a connected D60 IED or from an offline D60 settings file with the EnerVista UR
Setup software using the following procedure:
1. Right-click the connected UR-series relay or settings file and select Create ICD File.
2. The EnerVista UR Setup will prompt to save the file. Select the file path and enter the name for the ICD file, then click
OK to generate the file.
The time to create an ICD file from the offline D60 settings file is typically much quicker than create an ICD file directly from
the relay.
C.5.5 ABOUT SCD FILES
System configuration is performed in the system configurator. While many vendors (including GE Multilin) are working their
own system configuration tools, there are some system configurators available in the market (for example, Siemens DIGSI
version 4.6 or above and ASE Visual SCL Beta 0.12).
Although the configuration tools vary from one vendor to another, the procedure is pretty much the same. First, a substation
project must be created, either as an empty template or with some system information by importing a system specification
file (SSD). Then, IEDs are added to the substation. Since each IED is represented by its associated ICD, the ICD files are
imported into the substation project, and the system configurator validates the ICD files during the importing process. If the
ICD files are successfully imported into the substation project, it may be necessary to perform some additional minor steps
to attach the IEDs to the substation (see the system configurator manual for details).
Once all IEDs are inserted into the substation, further configuration is possible, such as:
• Assigning network addresses to individual IEDs.
• Customizing the prefixes of logical nodes.
• Creating cross-communication links (configuring GOOSE messages to send from one IED to others).
When system configurations are complete, the results are saved to an SCD file, which contains not only the configuration
for each IED in the substation, but also the system configuration for the entire substation. Finally, the SCD file is passed
back to the IED configurator (vendor specific tool) to update the new configuration into the IED.
The SCD file consists of at least five major sections:

• Header.
• Substation.
• Communication.
• IED section (one or more).
• DataTypeTemplates.
The root file structure of an SCD file is illustrated below.
SCL
Header (id, version, revision, toolID, nameStructure)
C Substation
Communication
IED Section (IED 1)
IED Section (IED 2)
Other IED Sections
DataTypeTemplates
842791A1.CDR
Figure C–6: SCD FILE STRUCTURE, SCL (ROOT) NODE

Like ICD files, the Header node identifies the SCD file and its version, and specifies options for the mapping of names to
signals.
The Substation node describes the substation parameters:
Substation
PowerSystemResource
EquipmentContainer Power Transformer
GeneralEquipment
EquipmentContainer
VoltageLevel Bay
Voltage
PowerSystemResource
Function SubFunction
GeneralEquipment
842792A1.CDR
Figure C–7: SCD FILE STRUCTURE, SUBSTATION NODE

The Communication node describes the direct communication connection possibilities between logical nodes by means of
logical buses (sub-networks) and IED access ports. The communication section is structured as follows.
Communication
SubNetwork (name)
ConnectedAP (IED 1)
Address
P (type)
Text
Other P elements
GSE (IdInst, cbName) C

Address
P (type)
Other GSE elements Text
Other P elements
ConnectedAP (IED 2)
Address
P (type)
Text
Other P elements
GSE (IdInst, cbName)
Address
P (type)
Text
Other P elements
Other GSE elements
Other ConnectedAP elements

842793A1.CDR
Figure C–8: SCD FILE STRUCTURE, COMMUNICATIONS NODE

The SubNetwork node contains all access points which can (logically) communicate with the sub-network protocol and
without the intervening router. The ConnectedAP node describes the IED access point connected to this sub-network. The
Address node contains the address parameters of the access point. The GSE node provides the address element for stat-
ing the control block related address parameters, where IdInst is the instance identification of the logical device within the
IED on which the control block is located, and cbName is the name of the control block.

The IED Section node describes the configuration of an IED.
IED Section (IED 1)
AccessPoint (name)
Server
Authentication (none)
LDevice (inst)
LN0 (InType, InClass, inst)
DataSet elements
C ReportControl elements
DOI elements
Inputs
ExtRef (iedName, ldInst, prefix, lnClass, lnInst, doName, daName, intAddr)
Other ExtRef elements
GSEControl elements
842794A1.CDR
Figure C–9: SCD FILE STRUCTURE, IED NODE
C.5.6 IMPORTING AN SCD FILE WITH ENERVISTA UR SETUP
The following procedure describes how to update the D60 with the new configuration from an SCD file with the EnerVista
UR Setup software.
1. Right-click anywhere in the files panel and select the Import Contents From SCD File item.
2. Select the saved SCD file and click Open.

3. The software will open the SCD file and then prompt the user to save a UR-series settings file. Select a location and
name for the URS (UR-series relay settings) file.
If there is more than one GE Multilin IED defined in the SCD file, the software prompt the user to save a UR-series set-
tings file for each IED.
4. After the URS file is created, modify any settings (if required).
5. To update the relay with the new settings, right-click on the settings file in the settings tree and select the Write Set-
tings File to Device item.
6. The software will prompt for the target device. Select the target device from the list provided and click Send. The new
settings will be updated to the selected device.

C.6 ACSI CONFORMANCE APPENDIX C
C.6ACSI CONFORMANCE C.6.1 ACSI BASIC CONFORMANCE STATEMENT
SERVICES SERVER/ UR-FAMILY

PUBLISHER
CLIENT-SERVER ROLES
B11 Server side (of Two-party Application-Association) c1 Yes
B12 Client side (of Two-party Application-Association) ---
SCSMS SUPPORTED
B21 SCSM: IEC 61850-8-1 used Yes
B22 SCSM: IEC 61850-9-1 used
B23 SCSM: IEC 61850-9-2 used
C B24 SCSM: other

GENERIC SUBSTATION EVENT MODEL (GSE)
B31 Publisher side O Yes
B32 Subscriber side --- Yes
TRANSMISSION OF SAMPLED VALUE MODEL (SVC)
B41 Publisher side O
B42 Subscriber side ---
c1: shall be "M" if support for LOGICAL-DEVICE model has been declared
O: Optional
NOTE M: Mandatory
C.6.2 ACSI MODELS CONFORMANCE STATEMENT

PUBLISHER
IF SERVER SIDE (B11) SUPPORTED
M1 Logical device c2 Yes
M2 Logical node c3 Yes
M3 Data c4 Yes
M4 Data set c5 Yes
M5 Substitution O
M6 Setting group control O
REPORTING
M7 Buffered report control O Yes
M7-1 sequence-number
M7-2 report-time-stamp
M7-3 reason-for-inclusion
M7-4 data-set-name
M7-5 data-reference
M7-6 buffer-overflow
M7-7 entryID
M7-8 BufTm
M7-9 IntgPd
M7-10 GI
M8 Unbuffered report control O Yes
M8-1 sequence-number
M8-2 report-time-stamp
M8-3 reason-for-inclusion

APPENDIX C C.6 ACSI CONFORMANCE

PUBLISHER
M8-4 data-set-name
M8-5 data-reference
M8-6 BufTm
M8-7 IntgPd
M8-8 GI
Logging O
M9 Log control O
M9-1 IntgPd
M10 Log O
M11 Control M Yes
IF GSE (B31/32) IS SUPPORTED C
GOOSE O Yes
M12-1 entryID
M12-2 DataReflnc
M13 GSSE O Yes
IF SVC (B41/B42) IS SUPPORTED
M14 Multicast SVC O
M15 Unicast SVC O
M16 Time M Yes
M17 File transfer O Yes
c2: shall be "M" if support for LOGICAL-NODE model has been declared
c3: shall be "M" if support for DATA model has been declared
NOTE c4: shall be "M" if support for DATA-SET, Substitution, Report, Log Control, or Time models has been declared
c5: shall be "M" if support for Report, GSE, or SMV models has been declared
M: Mandatory
C.6.3 ACSI SERVICES CONFORMANCE STATEMENT
In the table below, the acronym AA refers to Application Associations (TP: Two Party / MC: Multicast). The c6 to c10 entries
are defined in the notes following the table.
SERVICES AA: TP/MC SERVER/ UR FAMILY

PUBLISHER
SERVER (CLAUSE 7)
S1 ServerDirectory TP M Yes
APPLICATION ASSOCIATION (CLAUSE 8)
S2 Associate TP M Yes
S3 Abort TP M Yes
S4 Release TP M Yes
LOGICAL DEVICE (CLAUSE 9)
S5 LogicalDeviceDirectory TP M Yes
LOGICAL NODE (CLAUSE 10)
S6 LogicalNodeDirectory TP M Yes
S7 GetAllDataValues TP M Yes
DATA (CLAUSE 11)
S8 GetDataValues TP M Yes
S9 SetDataValues TP O Yes
S10 GetDataDirectory TP M Yes
S11 GetDataDefinition TP M Yes

C.6 ACSI CONFORMANCE APPENDIX C

PUBLISHER
DATA SET (CLAUSE 12)
S12 GetDataSetValues TP M Yes
S13 SetDataSetValues TP O
S14 CreateDataSet TP O
S15 DeleteDataSet TP O
S16 GetDataSetDirectory TP O Yes
SETTING GROUP CONTROL (CLAUSE 16)
S18 SelectActiveSG TP O
S19 SelectEditSG TP O
S20 SetSGValues TP O
C S21 ConfirmEditSGValues TP O
S22 GetSGValues TP O
S23 GetSGCBValues TP O
REPORTING (CLAUSE 17)
BUFFERED REPORT CONTROL BLOCK (BRCB)
S24 Report TP c6 Yes
S24-1 data-change (dchg) Yes
S24-2 qchg-change (qchg)
S24-3 data-update (dupd)
S25 GetBRCBValues TP c6 Yes
S26 SetBRCBValues TP c6 Yes
UNBUFFERED REPORT CONTROL BLOCK (URCB)
S27 Report TP c6 Yes
S27-1 data-change (dchg) Yes
S27-2 qchg-change (qchg)
S27-3 data-update (dupd)
S28 GetURCBValues TP c6 Yes
S29 SetURCBValues TP c6 Yes
LOGGING (CLAUSE 17)
LOG CONTROL BLOCK
S30 GetLCBValues TP M
S31 SetLCBValues TP M
LOG
S32 QueryLogByTime TP M
S33 QueryLogByEntry TP M
S34 GetLogStatusValues TP M
GENERIC SUBSTATION EVENT MODEL (GSE) (CLAUSE 18, ANNEX C)
GOOSE-CONTROL-BLOCK (CLAUSE 18)
S35 SendGOOSEMessage MC c8 Yes
S36 GetReference TP c9
S37 GetGOOSEElementNumber TP c9
S38 GetGoCBValues TP O Yes
S39 SetGoCBValues TP O Yes
GSSE-CONTROL-BLOCK (ANNEX C)
S40 SendGSSEMessage MC c8 Yes
S41 GetReference TP c9
S42 GetGSSEElementNumber TP c9
S43 GetGsCBValues TP O Yes

APPENDIX C C.6 ACSI CONFORMANCE

PUBLISHER
S44 SetGsCBValues TP O Yes
TRANSMISSION OF SAMPLED VALUE MODEL (SVC) (CLAUSE 19)
MULTICAST SVC
S45 SendMSVMessage MC c10
S46 GetMSVCBValues TP O
S47 SetMSVCBValues TP O
UNICAST SVC
S48 SendUSVMessage MC c10
S49 GetUSVCBValues TP O
S50 SetUSVCBValues TP O
CONTROL (CLAUSE 20) C
S51 Select O Yes
S52 SelectWithValue TP O
S53 Cancel TP O Yes
S54 Operate TP M Yes
S55 Command-Termination TP O
S56 TimeActivated-Operate TP O
FILE TRANSFER (CLAUSE 23)
S57 GetFile TP M Yes
S58 SetFile TP O
S59 DeleteFile TP O
S60 GetFileAttributeValues TP M Yes
TIME (CLAUSE 5.5)
T1 Time resolution of internal clock 20
(nearest negative power of 2 in
seconds)
T2 Time accuracy of internal clock SNTP, IRIG-B
T3 Supported TimeStamp resolution 20
(nearest value of 2–n in seconds,
according to 6.1.2.9.3.2)
c6: shall declare support for at least one (BRCB or URCB)

c7: shall declare support for at least one (QueryLogByTime or QueryLogAfter)
NOTE c8: shall declare support for at least one (SendGOOSEMessage or SendGSSEMessage)
c9: shall declare support if TP association is available
c10: shall declare support for at least one (SendMSVMessage or SendUSVMessage)

C.7 LOGICAL NODES APPENDIX C
C.7LOGICAL NODES C.7.1 LOGICAL NODES TABLE
The UR-series of relays supports IEC 61850 logical nodes as indicated in the following table. Note that the actual instantia-
tion of each logical node is determined by the product order code. For example. the logical node “PDIS” (distance protec-
tion) is available only in the D60 Line Distance Relay.
Table C–1: IEC 61850 LOGICAL NODES (Sheet 1 of 4)

NODES UR-FAMILY
L: SYSTEM LOGICAL NODES
LPHD: Physical device information Yes
LLN0: Logical node zero Yes
LCCH: Physical communication channel supervision ---
C LGOS: GOOSE subscription ---
LSVS: Sampled value subscription ---
LTIM: Time management ---
LTMS: Time master supervision ---
LTRK: Service tracking ---
A: LOGICAL NODES FOR AUTOMATIC CONTROL
ANCR: Neutral current regulator ---
ARCO: Reactive power control ---
ATCC: Automatic tap changer controller ---
AVCO: Voltage control ---
C: LOGICAL NODES FOR CONTROL
CALH: Alarm handling ---
CCGR: Cooling group control ---
CILO: Interlocking ---
CPOW: Point-on-wave switching ---
CSWI: Switch controller Yes
CSYN: Synchronizer controller ---
F: LOGICAL NODES FOR FUNCTIONAL BLOCKS
FCNT: Counter ---
FCSD: Curve shape description ---
FFIL: Generic filler ---
FLIM: Control function output limitation ---
FPID: PID regulator ---
FRMP: Ramp function ---
FSPT: Set-point control function ---
FXOT: Action at over threshold ---
FXUT: Action at under threshold ---
G: LOGICAL NODES FOR GENERIC REFERENCES
GAPC: Generic automatic process control ---
GGIO: Generic process I/O Yes
GLOG: Generic log ---
GSAL: Generic security application ---
I: LOGICAL NODES FOR INTERFACING AND ARCHIVING
IARC: Archiving ---
IHMI: Human machine interface ---
ISAF: Safety alarm function ---
ITCI: Telecontrol interface ---
ITMI: Telemonitoring interface ---

APPENDIX C C.7 LOGICAL NODES

NODES UR-FAMILY
ITPC: Teleprotection communication interfaces ---
K: LOGICAL NODES FOR MECHANICAL AND NON-ELECTRIC PRIMARY EQUIPMENT
KFAN: Fan ---
KFIL: Filter ---
KPMP: Pump ---
KTNK: Tank ---
KVLV: Valve control ---
M: LOGICAL NODES FOR METERING AND MEASUREMENT
MENV: Environmental information ---
MFLK: Flicker measurement name
MHAI: Harmonics or interharmonics
---
---
C
MHAN: Non phase related harmonics or interharmonics ---
MHYD: Hydrological information ---
MMDC: DC measurement ---
MMET: Meteorological information ---
MMTN: Metering ---
MMTR: Metering ---
MMXN: Non-phase-related measurement Yes
MMXU: Measurement Yes
MSQI: Sequence and imbalance Yes
MSTA: Metering statistics ---
P: LOGICAL NODES FOR PROTECTION FUNCTIONS
PDIF: Differential Yes
PDIR: Direction comparison ---
PDIS: Distance Yes
PDOP: Directional overpower ---
PDUP: Directional underpower ---
PFRC: Rate of change of frequency ---
PHAR: Harmonic restraint ---
PHIZ: Ground detector ---
PIOC: Instantaneous overcurrent Yes
PMRI Motor restart inhibition ---
PMSS: Motor starting time supervision ---
POPF: Over power factor ---
PPAM: Phase angle measuring ---
PRTR: Rotor protection ---
PSCH: Protection scheme ---
PSDE: Sensitive directional earth fault ---
PTEF: Transient earth fault ---
PTOC: Time overcurrent Yes
PTOF: Overfrequency ---
PTOV: Overvoltage Yes
PTRC: Protection trip conditioning Yes
PTTR: Thermal overload ---
PTUC: Undercurrent ---
PTUF: Underfrequency ---
PTUV: Undervoltage Yes


NODES UR-FAMILY
PUPF: Underpower factor ---
PVOC: Voltage controlled time overcurrent ---
PVPH: Volts per Hz ---
PZSU: Zero speed or underspeed ---
Q: LOGICAL NODES FOR POWER QUALITY EVENTS
QFVR: Frequency variation ---
QITR: Current transient ---
QIUB: Current unbalance variation ---
QVTR: Voltage transient ---
C QVUB: Voltage unbalance variation

QVVR: Voltage variation
---
---
R: LOGICAL NODES FOR PROTECTION-RELATED FUNCTIONS
RADR: Disturbance recorder channel analogue ---
RBDR: Disturbance recorder channel binary ---
RBRF: Breaker failure ---
RDIR: Directional element ---
RDRE: Disturbance recorder function ---
RDRS: Disturbance record handling ---
RFLO: Fault locator Yes
RMXU: Differential measurements ---
RPSB: Power swing detection/blocking Yes
RREC: Autoreclosing Yes
RSYN: Synchronism-check or synchronizing ---
S: LOGICAL NODES FOR SENSORS AND MONITORING
SARC: Monitoring and diagnostics for arcs ---
SCBR: Circuit breaker supervision ---
SIMG: Insulation medium supervision (gas) ---
SIML: Insulation medium supervision (liquid) ---
SLTC: Tap changer supervision ---
SOPM: Supervision of operating mechanism ---
SPDC: Monitoring and diagnostics for partial discharges ---
SPTR: Power transformer supervision ---
SSWI: Circuit switch supervision ---
STMP: Temperature supervision ---
SVBR: Vibration supervision ---
T: LOGICAL NODES FOR INSTRUMENT TRANSFORMERS
TANG: Angle ---
TAXD: Axial displacement ---
TCTR: Current transformer ---
TDST: Distance ---
TFLW: Liquid flow ---
TFRQ: Frequency ---
TGSN: Generic sensor ---
THUM: Humidity ---
TLVL: Media level ---
TMGF: Magnetic field ---
TMVM: Movement sensor ---

APPENDIX C C.7 LOGICAL NODES

NODES UR-FAMILY
TPOS: Position indicator ---
TPRS: Pressure sensor ---
TRTN: Rotation transmitter ---
TSND: Sound pressure sensor ---
TTMP: Temperature sensor ---
TTNS: Mechanical tension ---
TVBR: Vibration sensor ---
TVTR: Voltage transformer ---
TWPH: Water acidity ---
X: LOGICAL NODES FOR SWITCHGEAR
XCBR: Circuit breaker Yes
C
XSWI: Circuit switch Yes
Y: LOGICAL NODES FOR POWER TRANSFORMERS
YEFN: Earth fault neutralizer (Petersen coil) ---
YLTC: Tap changer ---
YPSH: Power shunt ---
YPTR: Power transformer ---
Z: LOGICAL NODES FOR FURTHER POWER SYSTEM EQUIPMENT
ZAXN: Auxiliary network ---
ZBAT: Battery ---
ZBSH: Bushing ---
ZCAB: Power cable ---
ZCAP: Capacitor bank ---
ZCON: Converter ---
ZGEN: Generator ---
ZGIL: Gas insulated line ---
ZLIN: Power overhead line ---
ZMOT: Motor ---
ZREA: Reactor ---
ZRES: Resistor ---
ZRRC: Rotating reactive component ---
ZSAR: Surge arrestor ---
ZSCR: Semi-conductor controlled rectifier ---
ZSMC: Synchronous machine ---
ZTCF: Thyristor controlled frequency converter ---
ZTRC: Thyristor controlled reactive component ---


APPENDIX D D.1 IEC 60870-5-104 PROTOCOL
APPENDIX D IEC 60870-5-104 COMMS.D.1IEC 60870-5-104 PROTOCOL D.1.1 INTEROPERABILITY DOCUMENT
This document is adapted from the IEC 60870-5-104 standard. For this section the boxes indicate the following:  – used
in standard direction;  – not used;  – cannot be selected in IEC 60870-5-104 standard.
1. SYSTEM OR DEVICE:
 System Definition
 Controlling Station Definition (Master)
 Controlled Station Definition (Slave)
2. NETWORK CONFIGURATION:
 Point-to-Point  Multipoint
 Multiple Point-to-Point  Multipoint Star
3. PHYSICAL LAYER
Transmission Speed (control direction):
Unbalanced Interchange Unbalanced Interchange Balanced Interchange Circuit
Circuit V.24/V.28 Standard: Circuit V.24/V.28 Recommended X.24/X.27:
if >1200 bits/s: D
 100 bits/sec.  2400 bits/sec.  2400 bits/sec.
 600 bits/sec.  19200 bits/sec.
 56000 bits/sec.
 64000 bits/sec.
Transmission Speed (monitor direction):
Unbalanced Interchange Unbalanced Interchange Balanced Interchange Circuit
Circuit V.24/V.28 Standard: Circuit V.24/V.28 Recommended X.24/X.27:
if >1200 bits/s:
 56000 bits/sec.
 64000 bits/sec.
4. LINK LAYER
Link Transmission Procedure: Address Field of the Link:
 Balanced Transmission  Not Present (Balanced Transmission Only)
 Unbalanced Transmission  One Octet
 Two Octets
 Structured
 Unstructured
Frame Length (maximum length, number of octets): Not selectable in companion IEC 60870-5-104 standard
GE Multilin D60 Line Distance Protection System D-1

D.1 IEC 60870-5-104 PROTOCOL APPENDIX D
When using an unbalanced link layer, the following ADSU types are returned in class 2 messages (low priority) with the
indicated causes of transmission:
 The standard assignment of ADSUs to class 2 messages is used as follows:
 A special assignment of ADSUs to class 2 messages is used as follows:
5. APPLICATION LAYER
Transmission Mode for Application Data:
Mode 1 (least significant octet first), as defined in Clause 4.10 of IEC 60870-5-4, is used exclusively in this companion
standard.
Common Address of ADSU:
 One Octet
 Two Octets
Information Object Address:
 One Octet  Structured
D  Two Octets  Unstructured

 Three Octets
Cause of Transmission:
 One Octet
 Two Octets (with originator address). Originator address is set to zero if not used.
Maximum Length of APDU: 253 (the maximum length may be reduced by the system.
Selection of standard ASDUs:
For the following lists, the boxes indicate the following:  – used in standard direction;  – not used;  – cannot be
selected in IEC 60870-5-104 standard.
Process information in monitor direction
 <1> := Single-point information M_SP_NA_1
 <2> := Single-point information with time tag M_SP_TA_1
 <3> := Double-point information M_DP_NA_1
 <4> := Double-point information with time tag M_DP_TA_1
 <5> := Step position information M_ST_NA_1
 <6> := Step position information with time tag M_ST_TA_1
 <7> := Bitstring of 32 bits M_BO_NA_1
 <8> := Bitstring of 32 bits with time tag M_BO_TA_1
 <9> := Measured value, normalized value M_ME_NA_1
 <10> := Measured value, normalized value with time tag M_NE_TA_1
 <11> := Measured value, scaled value M_ME_NB_1
 <12> := Measured value, scaled value with time tag M_NE_TB_1
 <13> := Measured value, short floating point value M_ME_NC_1
 <14> := Measured value, short floating point value with time tag M_NE_TC_1
 <15> := Integrated totals M_IT_NA_1
 <16> := Integrated totals with time tag M_IT_TA_1
 <17> := Event of protection equipment with time tag M_EP_TA_1
 <18> := Packed start events of protection equipment with time tag M_EP_TB_1
 <19> := Packed output circuit information of protection equipment with time tag M_EP_TC_1
 <20> := Packed single-point information with status change detection M_SP_NA_1
D-2 D60 Line Distance Protection System GE Multilin

 <21> := Measured value, normalized value without quantity descriptor M_ME_ND_1
 <30> := Single-point information with time tag CP56Time2a M_SP_TB_1

 <31> := Double-point information with time tag CP56Time2a M_DP_TB_1
 <32> := Step position information with time tag CP56Time2a M_ST_TB_1
 <33> := Bitstring of 32 bits with time tag CP56Time2a M_BO_TB_1
 <34> := Measured value, normalized value with time tag CP56Time2a M_ME_TD_1
 <35> := Measured value, scaled value with time tag CP56Time2a M_ME_TE_1
 <36> := Measured value, short floating point value with time tag CP56Time2a M_ME_TF_1
 <37> := Integrated totals with time tag CP56Time2a M_IT_TB_1
 <38> := Event of protection equipment with time tag CP56Time2a M_EP_TD_1
 <39> := Packed start events of protection equipment with time tag CP56Time2a M_EP_TE_1
 <40> := Packed output circuit information of protection equipment with time tag CP56Time2a M_EP_TF_1
Either the ASDUs of the set <2>, <4>, <6>, <8>, <10>, <12>, <14>, <16>, <17>, <18>, and <19> or of the set
<30> to <40> are used.
Process information in control direction
 <45> := Single command C_SC_NA_1
D
 <46> := Double command C_DC_NA_1
 <47> := Regulating step command C_RC_NA_1
 <48> := Set point command, normalized value C_SE_NA_1
 <49> := Set point command, scaled value C_SE_NB_1
 <50> := Set point command, short floating point value C_SE_NC_1
 <51> := Bitstring of 32 bits C_BO_NA_1
 <58> := Single command with time tag CP56Time2a C_SC_TA_1

 <59> := Double command with time tag CP56Time2a C_DC_TA_1
 <60> := Regulating step command with time tag CP56Time2a C_RC_TA_1
 <61> := Set point command, normalized value with time tag CP56Time2a C_SE_TA_1
 <62> := Set point command, scaled value with time tag CP56Time2a C_SE_TB_1
 <63> := Set point command, short floating point value with time tag CP56Time2a C_SE_TC_1
 <64> := Bitstring of 32 bits with time tag CP56Time2a C_BO_TA_1
Either the ASDUs of the set <45> to <51> or of the set <58> to <64> are used.
System information in monitor direction
 <70> := End of initialization M_EI_NA_1
System information in control direction

 <100> := Interrogation command C_IC_NA_1
 <101> := Counter interrogation command C_CI_NA_1
 <102> := Read command C_RD_NA_1
 <103> := Clock synchronization command (see Clause 7.6 in standard) C_CS_NA_1
 <104> := Test command C_TS_NA_1
 <105> := Reset process command C_RP_NA_1
 <106> := Delay acquisition command C_CD_NA_1
 <107> := Test command with time tag CP56Time2a C_TS_TA_1

Parameter in control direction

 <110> := Parameter of measured value, normalized value PE_ME_NA_1
 <111> := Parameter of measured value, scaled value PE_ME_NB_1
 <112> := Parameter of measured value, short floating point value PE_ME_NC_1
 <113> := Parameter activation PE_AC_NA_1
File transfer
 <120> := File Ready F_FR_NA_1
 <121> := Section Ready F_SR_NA_1
 <122> := Call directory, select file, call file, call section F_SC_NA_1
 <123> := Last section, last segment F_LS_NA_1
 <124> := Ack file, ack section F_AF_NA_1
 <125> := Segment F_SG_NA_1
 <126> := Directory (blank or X, available only in monitor [standard] direction) C_CD_NA_1
Type identifier and cause of transmission assignments

D (station-specific parameters)
In the following table:
•Shaded boxes are not required.
•Black boxes are not permitted in this companion standard.
•Blank boxes indicate functions or ASDU not used.
•‘X’ if only used in the standard direction
TYPE IDENTIFICATION CAUSE OF TRANSMISSION
REQUEST BY GROUP <N> COUNTER REQ
UNKNOWN INFORMATION OBJECT ADDR

UNKNOWN COMMON ADDRESS OF ADSU
INTERROGATED BY GROUP <NUMBER>
RETURN INFO CAUSED BY LOCAL CMD
UNKNOWN CAUSE OF TRANSMISSION

UNKNOWN TYPE IDENTIFICATION
DEACTIVATION CONFIRMATION
ACTIVATION CONFIRMATION
ACTIVATION TERMINATION
REQUEST OR REQUESTED
BACKGROUND SCAN
PERIODIC, CYCLIC
FILE TRANSFER
SPONTANEOUS
DEACTIVATION
ACTIVATION
INITIALIZED
20 37
NO. MNEMONIC 1 2 3 4 5 6 7 8 9 10 11 12 13 to to 44 45 46 47
36 41
<1> M_SP_NA_1 X X X X X
<2> M_SP_TA_1
<3> M_DP_NA_1
<4> M_DP_TA_1
<5> M_ST_NA_1
<6> M_ST_TA_1
<7> M_BO_NA_1
<8> M_BO_TA_1
<9> M_ME_NA_1



BACKGROUND SCAN
PERIODIC, CYCLIC
FILE TRANSFER
SPONTANEOUS
DEACTIVATION
ACTIVATION
INITIALIZED
20 37
NO. MNEMONIC 1 2 3 4 5 6 7 8 9 10 11 12 13 to to 44 45 46 47
36 41
<10> M_ME_TA_1 D
<11> M_ME_NB_1
<12> M_ME_TB_1
<13> M_ME_NC_1 X X X X
<14> M_ME_TC_1
<15> M_IT_NA_1 X X
<16> M_IT_TA_1
<17> M_EP_TA_1
<18> M_EP_TB_1
<19> M_EP_TC_1
<20> M_PS_NA_1
<21> M_ME_ND_1
<30> M_SP_TB_1 X X X
<31> M_DP_TB_1
<32> M_ST_TB_1
<33> M_BO_TB_1
<34> M_ME_TD_1
<35> M_ME_TE_1
<36> M_ME_TF_1
<37> M_IT_TB_1 X X
<38> M_EP_TD_1
<39> M_EP_TE_1
<40> M_EP_TF_1
<45> C_SC_NA_1 X X X X X
<46> C_DC_NA_1
<47> C_RC_NA_1
<48> C_SE_NA_1
<49> C_SE_NB_1
<50> C_SE_NC_1
<51> C_BO_NA_1
<58> C_SC_TA_1 X X X X X
<59> C_DC_TA_1
<60> C_RC_TA_1



BACKGROUND SCAN
PERIODIC, CYCLIC
FILE TRANSFER
SPONTANEOUS
DEACTIVATION
ACTIVATION
INITIALIZED
20 37
NO. MNEMONIC 1 2 3 4 5 6 7 8 9 10 11 12 13 to to 44 45 46 47
36 41
D <61>
<62>
C_SE_TA_1
C_SE_TB_1
<63> C_SE_TC_1
<64> C_BO_TA_1
<70> M_EI_NA_1*) X
<100> C_IC_NA_1 X X X X X
<101> C_CI_NA_1 X X X
<102> C_RD_NA_1 X
<103> C_CS_NA_1 X X X
<104> C_TS_NA_1
<105> C_RP_NA_1 X X
<106> C_CD_NA_1
<107> C_TS_TA_1
<110> P_ME_NA_1
<111> P_ME_NB_1
<112> P_ME_NC_1 X X X
<113> P_AC_NA_1
<120> F_FR_NA_1
<121> F_SR_NA_1
<122> F_SC_NA_1
<123> F_LS_NA_1
<124> F_AF_NA_1
<125> F_SG_NA_1
<126> F_DR_TA_1*)
6. BASIC APPLICATION FUNCTIONS

Station Initialization:
 Remote initialization
Cyclic Data Transmission:
 Cyclic data transmission
Read Procedure:
 Read procedure

Spontaneous Transmission:
 Spontaneous transmission
Double transmission of information objects with cause of transmission spontaneous:
The following type identifications may be transmitted in succession caused by a single status change of an information
object. The particular information object addresses for which double transmission is enabled are defined in a project-
specific list.
 Single point information: M_SP_NA_1, M_SP_TA_1, M_SP_TB_1, and M_PS_NA_1
 Double point information: M_DP_NA_1, M_DP_TA_1, and M_DP_TB_1
 Step position information: M_ST_NA_1, M_ST_TA_1, and M_ST_TB_1
 Bitstring of 32 bits: M_BO_NA_1, M_BO_TA_1, and M_BO_TB_1 (if defined for a specific project)
 Measured value, normalized value: M_ME_NA_1, M_ME_TA_1, M_ME_ND_1, and M_ME_TD_1
 Measured value, scaled value: M_ME_NB_1, M_ME_TB_1, and M_ME_TE_1
 Measured value, short floating point number: M_ME_NC_1, M_ME_TC_1, and M_ME_TF_1
Station interrogation:
 Global D
 Group 1  Group 5  Group 9  Group 13
Clock synchronization:
 Clock synchronization (optional, see Clause 7.6)
Command transmission:
 Direct command transmission
 Direct setpoint command transmission
 Select and execute command
 Select and execute setpoint command
 C_SE ACTTERM used
 No additional definition
 Short pulse duration (duration determined by a system parameter in the outstation)
 Long pulse duration (duration determined by a system parameter in the outstation)
 Persistent output
 Supervision of maximum delay in command direction of commands and setpoint commands

Maximum allowable delay of commands and setpoint commands: 10 s
Transmission of integrated totals:
 Mode A: Local freeze with spontaneous transmission
 Mode B: Local freeze with counter interrogation
 Mode C: Freeze and transmit by counter-interrogation commands
 Mode D: Freeze by counter-interrogation command, frozen values reported simultaneously
 Counter read
 Counter freeze without reset

 Counter freeze with reset

 Counter reset
 General request counter

 Request counter group 1
Parameter loading:
 Threshold value
 Smoothing factor
 Low limit for transmission of measured values
 High limit for transmission of measured values
Parameter activation:
D  Activation/deactivation of persistent cyclic or periodic transmission of the addressed object
Test procedure:
 Test procedure
File transfer:
File transfer in monitor direction:
 Transparent file
 Transmission of disturbance data of protection equipment
 Transmission of sequences of events
 Transmission of sequences of recorded analog values
File transfer in control direction:
 Transparent file
Background scan:
 Background scan
Acquisition of transmission delay:
 Acquisition of transmission delay
Definition of time outs:

PARAMETER DEFAULT REMARKS SELECTED
VALUE VALUE
t0 30 s Timeout of connection establishment 120 s
t1 15 s Timeout of send or test APDUs 15 s
t2 10 s Timeout for acknowledgements in case of no data messages t2 < t1 10 s
t3 20 s Timeout for sending test frames in case of a long idle state 20 s
Maximum range of values for all time outs: 1 to 255 s, accuracy 1 s

Maximum number of outstanding I-format APDUs k and latest acknowledge APDUs (w):
PARAMETER DEFAULT REMARKS SELECTED
VALUE VALUE
k 12 APDUs Maximum difference receive sequence number to send state variable 12 APDUs
w 8 APDUs Latest acknowledge after receiving w I-format APDUs 8 APDUs

Maximum range of values k: 1 to 32767 (215 – 1) APDUs, accuracy 1 APDU

Maximum range of values w: 1 to 32767 APDUs, accuracy 1 APDU
Recommendation: w should not exceed two-thirds of k.
Portnumber:
PARAMETER VALUE REMARKS
Portnumber 2404 In all cases
RFC 2200 suite:

RFC 2200 is an official Internet Standard which describes the state of standardization of protocols used in the Internet
as determined by the Internet Architecture Board (IAB). It offers a broad spectrum of actual standards used in the Inter-
net. The suitable selection of documents from RFC 2200 defined in this standard for given projects has to be chosen
by the user of this standard.
 Ethernet 802.3
 Serial X.21 interface
 Other selection(s) from RFC 2200 (list below if selected)
D.1.2 POINTS LIST

D
The IEC 60870-5-104 data points are configured through the SETTINGS  PRODUCT SETUP  COMMUNICATIONS  DNP /
IEC104 POINT LISTS menu. Refer to the Communications section of Chapter 5 for additional details.


APPENDIX E E.1 DEVICE PROFILE DOCUMENT
APPENDIX E DNP COMMUNICATIONSE.1DEVICE PROFILE DOCUMENT E.1.1 DNP V3.00 DEVICE PROFILE
The following table provides a ‘Device Profile Document’ in the standard format defined in the DNP 3.0 Subset Definitions
Document.
Table E–1: DNP V3.00 DEVICE PROFILE (Sheet 1 of 3)
(Also see the IMPLEMENTATION TABLE in the following section)
Vendor Name: General Electric Multilin
Device Name: UR Series Relay
Highest DNP Level Supported: Device Function:

For Requests: Level 2  Master
For Responses: Level 2  Slave
Notable objects, functions, and/or qualifiers supported in addition to the Highest DNP Levels Supported (the complete
list is described in the attached table):
Binary Inputs (Object 1)
Binary Input Changes (Object 2)
Binary Outputs (Object 10)
Control Relay Output Block (Object 12)
Binary Counters (Object 20)
E
Frozen Counters (Object 21)
Counter Change Event (Object 22)
Frozen Counter Event (Object 23)
Analog Inputs (Object 30)
Analog Input Changes (Object 32)
Analog Deadbands (Object 34)
Time and Date (Object 50)
File Transfer (Object 70)
Internal Indications (Object 80)
Maximum Data Link Frame Size (octets): Maximum Application Fragment Size (octets):
Transmitted: 292 Transmitted: configurable up to 2048
Received: 292 Received: 2048
Maximum Data Link Re-tries: Maximum Application Layer Re-tries:

 None  None
 Fixed at 3  Configurable
 Configurable
Requires Data Link Layer Confirmation:

 Never
 Always
 Sometimes
 Configurable
GE Multilin D60 Line Distance Protection System E-1

E.1 DEVICE PROFILE DOCUMENT APPENDIX E
Requires Application Layer Confirmation:

 Never
 Always
 When reporting Event Data
 When sending multi-fragment responses
 Sometimes
 Configurable
Timeouts while waiting for:

Data Link Confirm:  None  Fixed at ____  Variable  Configurable
Complete Appl. Fragment:  None  Fixed at ____  Variable  Configurable
Application Confirm:  None  Fixed at 10 s  Variable  Configurable
Complete Appl. Response:  None  Fixed at ____  Variable  Configurable
Others:
Transmission Delay: No intentional delay
Need Time Interval: Configurable (default = 24 hrs.)
Select/Operate Arm Timeout: 10 s
Binary input change scanning period: 8 times per power system cycle
Analog input change scanning period: 500 ms
E Counter change scanning period:

Frozen counter event scanning period:
500 ms
500 ms
Unsolicited response notification delay: 100 ms
Unsolicited response retry delay configurable 0 to 60 sec.
Sends/Executes Control Operations:

WRITE Binary Outputs  Never  Always  Sometimes  Configurable
SELECT/OPERATE  Never  Always  Sometimes  Configurable
DIRECT OPERATE  Never  Always  Sometimes  Configurable
DIRECT OPERATE – NO ACK  Never  Always  Sometimes  Configurable
Count  1  Never  Always  Sometimes  Configurable

Pulse On  Never  Always  Sometimes  Configurable
Pulse Off  Never  Always  Sometimes  Configurable
Latch On  Never  Always  Sometimes  Configurable
Latch Off  Never  Always  Sometimes  Configurable
Queue  Never  Always  Sometimes  Configurable

Clear Queue  Never  Always  Sometimes  Configurable
Explanation of ‘Sometimes’: Object 12 points are mapped to UR Virtual Inputs. The persistence of Virtual Inputs is
determined by the VIRTUAL INPUT X TYPE settings. Both “Pulse On” and “Latch On” operations perform the same func-
tion in the UR; that is, the appropriate Virtual Input is put into the “On” state. If the Virtual Input is set to “Self-Reset”,
it will reset after one pass of FlexLogic. The On/Off times and Count value are ignored. “Pulse Off” and “Latch Off”
operations put the appropriate Virtual Input into the “Off” state. “Trip” and “Close” operations both put the appropriate
Virtual Input into the “On” state.
E-2 D60 Line Distance Protection System GE Multilin

Reports Binary Input Change Events when no Reports time-tagged Binary Input Change Events when no
specific variation requested: specific variation requested:
 Never  Never
 Only time-tagged  Binary Input Change With Time
 Only non-time-tagged  Binary Input Change With Relative Time
 Configurable  Configurable (attach explanation)
Sends Unsolicited Responses: Sends Static Data in Unsolicited Responses:

 Never  Never
 Configurable  When Device Restarts
 Only certain objects  When Status Flags Change
 Sometimes (attach explanation)
 ENABLE/DISABLE unsolicited Function No other options are permitted.
codes supported
Default Counter Object/Variation: Counters Roll Over at:

 No Counters Reported  No Counters Reported
 Configurable (attach explanation)  Configurable (attach explanation)
 Default Object: 20  16 Bits (Counter 8)
Default Variation: 1  32 Bits (Counters 0 to 7, 9)
 Point-by-point list attached  Other Value: _____
 Point-by-point list attached E
Sends Multi-Fragment Responses:
 Yes
 No

E.1.2 IMPLEMENTATION TABLE
The following table identifies the variations, function codes, and qualifiers supported by the D60 in both request messages
and in response messages. For static (non-change-event) objects, requests sent with qualifiers 00, 01, 06, 07, or 08, will be
responded with qualifiers 00 or 01. Static object requests sent with qualifiers 17 or 28 will be responded with qualifiers 17 or
28. For change-event objects, qualifiers 17 or 28 are always responded.
Table E–2: IMPLEMENTATION TABLE (Sheet 1 of 4)

OBJECT REQUEST RESPONSE
OBJECT VARIATION DESCRIPTION FUNCTION QUALIFIER FUNCTION QUALIFIER
NO. NO. CODES (DEC) CODES (HEX) CODES (DEC) CODES (HEX)
1 0 Binary Input (Variation 0 is used to request 1 (read) 00, 01 (start-stop)
default variation) 22 (assign class) 06 (no range, or all)
07, 08 (limited quantity)
17, 28 (index)
1 Binary Input 1 (read) 00, 01 (start-stop) 129 (response) 00, 01 (start-stop)
22 (assign class) 06 (no range, or all) 17, 28 (index)
07, 08 (limited quantity) (see Note 2)
17, 28 (index)
2 Binary Input with Status 1 (read) 00, 01 (start-stop) 129 (response) 00, 01 (start-stop)
17, 28 (index)
2 0 Binary Input Change (Variation 0 is used to 1 (read) 06 (no range, or all)
request default variation) 07, 08 (limited quantity)
1 Binary Input Change without Time 1 (read) 06 (no range, or all) 129 (response) 17, 28 (index)
07, 08 (limited quantity) 130 (unsol. resp.)
E 2 Binary Input Change with Time 1 (read) 06 (no range, or all)
129 (response
130 (unsol. resp.)
17, 28 (index)
3 Binary Input Change with Relative Time 1 (read) 06 (no range, or all)
10 0 Binary Output Status (Variation 0 is used to 1 (read) 00, 01(start-stop)
request default variation) 06 (no range, or all)
17, 28 (index)
2 Binary Output Status 1 (read) 00, 01 (start-stop) 129 (response) 00, 01 (start-stop)
06 (no range, or all) 17, 28 (index)
17, 28 (index)
12 1 Control Relay Output Block 3 (select) 00, 01 (start-stop) 129 (response) echo of request
4 (operate) 07, 08 (limited quantity)
5 (direct op) 17, 28 (index)
6 (dir. op, noack)
20 0 Binary Counter 1 (read) 00, 01(start-stop)
(Variation 0 is used to request default 7 (freeze) 06(no range, or all)
variation) 8 (freeze noack) 07, 08(limited quantity)
9 (freeze clear) 17, 28(index)
10 (frz. cl. noack)
22 (assign class)
1 32-Bit Binary Counter 1 (read) 00, 01 (start-stop) 129 (response) 00, 01 (start-stop)
7 (freeze) 06 (no range, or all) 17, 28 (index)
8 (freeze noack) 07, 08 (limited quantity) (see Note 2)
9 (freeze clear) 17, 28 (index)
10 (frz. cl. noack)
22 (assign class)
Note 1: A default variation refers to the variation responded when variation 0 is requested and/or in class 0, 1, 2, or 3 scans. The default varia-
tions for object types 1, 2, 20, 21, 22, 23, 30, and 32 are selected via relay settings. Refer to the Communications section in Chapter 5
for details. This optimizes the class 0 poll data size.
Note 2: For static (non-change-event) objects, qualifiers 17 or 28 are only responded when a request is sent with qualifiers 17 or 28, respec-
tively. Otherwise, static object requests sent with qualifiers 00, 01, 06, 07, or 08, will be responded with qualifiers 00 or 01 (for change-
event objects, qualifiers 17 or 28 are always responded.)
Note 3: Cold restarts are implemented the same as warm restarts – the D60 is not restarted, but the DNP process is restarted.


20 2 16-Bit Binary Counter 1 (read) 00, 01 (start-stop) 129 (response) 00, 01 (start-stop)
cont’d 7 (freeze) 06 (no range, or all) 17, 28 (index)
10 (frz. cl. noack)
22 (assign class)
5 32-Bit Binary Counter without Flag 1 (read) 00, 01 (start-stop) 129 (response) 00, 01 (start-stop)
10 (frz. cl. noack)
22 (assign class)
6 16-Bit Binary Counter without Flag 1 (read) 00, 01 (start-stop) 129 (response) 00, 01 (start-stop)
10 (frz. cl. noack)
22 (assign class)
21 0 Frozen Counter 1 (read) 00, 01 (start-stop)
(Variation 0 is used to request default 22 (assign class) 06 (no range, or all)
variation) 07, 08 (limited quantity)
17, 28 (index)
1 32-Bit Frozen Counter 1 (read) 00, 01 (start-stop) 129 (response) 00, 01 (start-stop)
17, 28 (index) E
2 16-Bit Frozen Counter 1 (read) 00, 01 (start-stop) 129 (response) 00, 01 (start-stop)
17, 28 (index)
9 32-Bit Frozen Counter without Flag 1 (read) 00, 01 (start-stop) 129 (response) 00, 01 (start-stop)
17, 28 (index)
10 16-Bit Frozen Counter without Flag 1 (read) 00, 01 (start-stop) 129 (response) 00, 01 (start-stop)
17, 28 (index)
22 0 Counter Change Event (Variation 0 is used 1 (read) 06 (no range, or all)
to request default variation) 07, 08 (limited quantity)
1 32-Bit Counter Change Event 1 (read) 06 (no range, or all) 129 (response) 17, 28 (index)
2 16-Bit Counter Change Event 1 (read) 06 (no range, or all) 129 (response) 17, 28 (index)
5 32-Bit Counter Change Event with Time 1 (read) 06 (no range, or all) 129 (response) 17, 28 (index)
6 16-Bit Counter Change Event with Time 1 (read) 06 (no range, or all) 129 (response) 17, 28 (index)
23 0 Frozen Counter Event (Variation 0 is used 1 (read) 06 (no range, or all)
1 32-Bit Frozen Counter Event 1 (read) 06 (no range, or all) 129 (response) 17, 28 (index)
2 16-Bit Frozen Counter Event 1 (read) 06 (no range, or all) 129 (response) 17, 28 (index)


23 5 32-Bit Frozen Counter Event with Time 1 (read) 06 (no range, or all) 129 (response) 17, 28 (index)
cont’d 07, 08 (limited quantity) 130 (unsol. resp.)
6 16-Bit Frozen Counter Event with Time 1 (read) 06 (no range, or all) 129 (response) 17, 28 (index)
30 0 Analog Input (Variation 0 is used to request 1 (read) 00, 01 (start-stop)
default variation) 22 (assign class) 06 (no range, or all)
17, 28 (index)
1 32-Bit Analog Input 1 (read) 00, 01 (start-stop) 129 (response) 00, 01 (start-stop)
17, 28 (index)
2 16-Bit Analog Input 1 (read) 00, 01 (start-stop) 129 (response) 00, 01 (start-stop)
17, 28 (index)
3 32-Bit Analog Input without Flag 1 (read) 00, 01 (start-stop) 129 (response) 00, 01 (start-stop)
17, 28 (index)
4 16-Bit Analog Input without Flag 1 (read) 00, 01 (start-stop) 129 (response) 00, 01 (start-stop)
17, 28 (index)
E 5 short floating point 1 (read)

22 (assign class)
00, 01 (start-stop)
06(no range, or all)
129 (response) 00, 01 (start-stop)
17, 28 (index)
07, 08(limited quantity) (see Note 2)
17, 28(index)
32 0 Analog Change Event (Variation 0 is used 1 (read) 06 (no range, or all)
1 32-Bit Analog Change Event without Time 1 (read) 06 (no range, or all) 129 (response) 17, 28 (index)
2 16-Bit Analog Change Event without Time 1 (read) 06 (no range, or all) 129 (response) 17, 28 (index)
3 32-Bit Analog Change Event with Time 1 (read) 06 (no range, or all) 129 (response) 17, 28 (index)
4 16-Bit Analog Change Event with Time 1 (read) 06 (no range, or all) 129 (response) 17, 28 (index)
5 short floating point Analog Change Event 1 (read) 06 (no range, or all) 129 (response) 17, 28 (index)
without Time 07, 08 (limited quantity) 130 (unsol. resp.)
7 short floating point Analog Change Event 1 (read) 06 (no range, or all) 129 (response) 17, 28 (index)
with Time 07, 08 (limited quantity) 130 (unsol. resp.)
34 0 Analog Input Reporting Deadband 1 (read) 00, 01 (start-stop)
(Variation 0 is used to request default 06 (no range, or all)
variation) 07, 08 (limited quantity)
17, 28 (index)
1 16-bit Analog Input Reporting Deadband 1 (read) 00, 01 (start-stop) 129 (response) 00, 01 (start-stop)
(default – see Note 1) 06 (no range, or all) 17, 28 (index)
17, 28 (index)
2 (write) 00, 01 (start-stop)
17, 28 (index)


34 2 32-bit Analog Input Reporting Deadband 1 (read) 00, 01 (start-stop) 129 (response) 00, 01 (start-stop)
cont’d 06 (no range, or all) 17, 28 (index)
17, 28 (index)
2 (write) 00, 01 (start-stop)
17, 28 (index)
3 Short floating point Analog Input Reporting 1 (read) 00, 01 (start-stop) 129 (response) 00, 01 (start-stop)
Deadband 06 (no range, or all) 17, 28 (index)
17, 28 (index)
50 1 Time and Date 1 (read) 00, 01 (start-stop) 129 (response) 00, 01 (start-stop)
(default – see Note 1) 2 (write) 06 (no range, or all) 17, 28 (index)
07 (limited qty=1) (see Note 2)
08 (limited quantity)
17, 28 (index)
52 2 Time Delay Fine 129 (response) 07 (limited quantity)
(quantity = 1)
60 0 Class 0, 1, 2, and 3 Data 1 (read) 06 (no range, or all)
20 (enable unsol)
21 (disable unsol)
22 (assign class)
1 Class 0 Data 1 (read) 06 (no range, or all)
22 (assign class)
2
3
Class 1 Data
Class 2 Data
1 (read)
20 (enable unsol)
06 (no range, or all)
07, 08 (limited quantity) E
4 Class 3 Data 21 (disable unsol)
22 (assign class)
70 0 File event - any variation 1 (read) 06 (no range, or all)
22 (assign class) 06 (no range, or all)
2 File authentication 29 (authenticate) 5b (free format) 129 (response) 5b (free format)
3 File command 25 (open) 5b (free format)
27 (delete)
4 File command status 26 (close) 5b (free format) 129 (response) 5b (free format)
30 (abort) 130 (unsol. resp.)
5 File transfer 1 (read) 5b (free format) 129 (response) 5b (free format)
2 (write) 130 (unsol. resp.)
6 File transfer status 129 (response) 5b (free format)
130 (unsol. resp.)
7 File descriptor 28 (get file info.) 5b (free format) 129 (response) 5b (free format)
130 (unsol. resp.)
80 1 Internal Indications 1 (read) 00, 01 (start-stop) 129 (response) 00, 01 (start-stop)
(index =7)
2 (write) 00 (start-stop)
(see Note 3) (index =7)
--- No Object (function code only) 13 (cold restart)
see Note 3
--- No Object (function code only) 14 (warm restart)
--- No Object (function code only) 23 (delay meas.)

E.2 DNP POINT LISTS APPENDIX E
E.2DNP POINT LISTS E.2.1 BINARY INPUT POINTS
The DNP binary input data points are configured through the PRODUCT SETUP  COMMUNICATIONS  DNP / IEC104 POINT
LISTS  BINARY INPUT / MSP POINTS menu. Refer to the Communications section of Chapter 5 for additional details. When a
freeze function is performed on a binary counter point, the frozen value is available in the corresponding frozen counter
point.
BINARY INPUT POINTS

Static (Steady-State) Object Number: 1
Change Event Object Number: 2
Request Function Codes supported: 1 (read), 22 (assign class)
Static Variation reported when variation 0 requested: 2 (Binary Input with status), Configurable
Change Event Variation reported when variation 0 requested: 2 (Binary Input Change with Time), Configurable
Change Event Scan Rate: 8 times per power system cycle
Change Event Buffer Size: 500
Default Class for All Points: 1

APPENDIX E E.2 DNP POINT LISTS
E.2.2 BINARY AND CONTROL RELAY OUTPUT
Supported Control Relay Output Block fields: Pulse On, Pulse Off, Latch On, Latch Off, Paired Trip, Paired Close.
BINARY OUTPUT STATUS POINTS

Object Number: 10
Request Function Codes supported: 1 (read)
Default Variation reported when Variation 0 requested: 2 (Binary Output Status)
CONTROL RELAY OUTPUT BLOCKS
Object Number: 12
Request Function Codes supported: 3 (select), 4 (operate), 5 (direct operate), 6 (direct operate, noack)
Table E–3: BINARY/CONTROL OUTPUTS Table E–3: BINARY/CONTROL OUTPUTS

POINT NAME/DESCRIPTION POINT NAME/DESCRIPTION
0 Virtual Input 1 32 Virtual Input 33
6
7
Virtual Input 7
Virtual Input 8
38
39
Virtual Input 39
Virtual Input 40
E

E.2.3 COUNTERS
The following table lists both Binary Counters (Object 20) and Frozen Counters (Object 21). When a freeze function is per-
formed on a Binary Counter point, the frozen value is available in the corresponding Frozen Counter point.
BINARY COUNTERS
Request Function Codes supported: 1 (read), 7 (freeze), 8 (freeze noack), 9 (freeze and clear),
10 (freeze and clear, noack), 22 (assign class)
Static Variation reported when variation 0 requested: 1 (32-Bit Binary Counter with Flag)
Change Event Variation reported when variation 0 requested: 1 (32-Bit Counter Change Event without time)
Default Class for all points: 3
FROZEN COUNTERS
Request Function Codes supported: 1 (read)
Static Variation reported when variation 0 requested: 1 (32-Bit Frozen Counter with Flag)
E Change Event Variation reported when variation 0 requested: 1 (32-Bit Frozen Counter Event without time)
Default Class for all points: 3
Table E–4: BINARY AND FROZEN COUNTERS

POINT NAME/DESCRIPTION
INDEX
0 Digital Counter 1
1 Digital Counter 2
2 Digital Counter 3
3 Digital Counter 4
4 Digital Counter 5
5 Digital Counter 6
6 Digital Counter 7
7 Digital Counter 8
8 Oscillography Trigger Count
9 Events Since Last Clear
A counter freeze command has no meaning for counters 8 and 9. D60 Digital Counter values are represented as 32-bit
integers. The DNP 3.0 protocol defines counters to be unsigned integers. Care should be taken when interpreting negative
counter values.

APPENDIX E E.2 DNP POINT LISTS
E.2.4 ANALOG INPUTS
The DNP analog input data points are configured through the PRODUCT SETUP  COMMUNICATIONS  DNP / IEC104 POINT
LISTS  ANALOG INPUT / MME POINTS menu. Refer to the Communications section of Chapter 5 for additional details.
It is important to note that 16-bit and 32-bit variations of analog inputs are transmitted through DNP as signed numbers.
Even for analog input points that are not valid as negative values, the maximum positive representation is 32767 for 16-bit
values and 2147483647 for 32-bit values. This is a DNP requirement.
The deadbands for all Analog Input points are in the same units as the Analog Input quantity. For example, an Analog Input
quantity measured in volts has a corresponding deadband in units of volts. This is in conformance with DNP Technical Bul-
letin 9809-001: Analog Input Reporting Deadband. Relay settings are available to set default deadband values according to
data type. Deadbands for individual Analog Input Points can be set using DNP Object 34.

Request Function Codes supported: 1 (read), 2 (write, deadbands only), 22 (assign class)
Static Variation reported when variation 0 requested: 1 (32-Bit Analog Input)
Change Event Variation reported when variation 0 requested: 1 (Analog Change Event without Time)
Change Event Scan Rate: defaults to 500 ms
Default Class for all Points: 2
E


APPENDIX F F.1 RADIUS SERVER CONFIGURATION
APPENDIX F RADIUS SERVERF.1 RADIUS SERVER CONFIGURATION F.1.1 RADIUS SERVER CONFIGURATION
The following procedure is an example of how to set up a simple RADIUS server, where the third-party tool used is also an
example.
1. Download and install FreeRADIUS as the RADIUS server.
2. In the RADIUSD.CONF file, locate the "bind_address" field and enter your RADIUS server IP address.
3. In the USERS.CONF file in the <Path_to_Radius>\etc\raddb folder, add the following text to configure a user "Tester"
with an Administrator role.
Tester:
->User-Password == "Testing1!1"
->GE-UR-Role = Administrator
4. In the CLIENTS.CONF file in the <Path_to_Radius>\etc\raddb folder, add the following text to define a RADIUS client,
where the client IP address is 10.0.0.2, the subnet mask is 255.255.255.0, the shared secret specified here is also
configured on the UR device for successful authentication, and the shortname is a short, optional alias that can be
used in place of the IP address.
client 10.0.0.2/24 {
secret = testing123
shortname = private-network-1
}
5. In the <Path_to_Radius>\etc\raddb folder, create a file called dictionary.ge and add the following content.
# ##########################################################
# GE VSAs
############################################################
VENDOR GE 2910
# Management authorization
BEGIN-VENDOR GE
# Role ID F
ATTRIBUTE GE-UR-Role 1 integer
# GE-UR-ROLE values
VALUE GE-UR-Role Administrator 1
VALUE GE-UR-Role Supervisor 2
VALUE GE-UR-Role Engineer 3
VALUE GE-UR-Role Operator 4
VALUE GE-UR-Role Observer 5
END-VENDOR GE
#############################################################
6. In the dictionary file in the <Path_to_Radius>\etc\raddb folder, add the following line.
$INCLUDE dictionary.ge
7. For the first start, run the RADIUS server in debug mode by entering
<Path_to_Radius>/start_radiusd_debug.bat
8. Set up the RADIUS client on the UR as follows. Access Device > Settings > Product Setup > Security. Configure the
IP address and ports for the RADIUS server. Leave the GE vendor ID field at the default of 2910. Update the RADIUS
shared secret as specified in the CLIENTS.CONF file.
GE Multilin D60 Line Distance Protection System F-1

F.1 RADIUS SERVER CONFIGURATION APPENDIX F
F-2 D60 Line Distance Protection System GE Multilin

APPENDIX G G.1 CHANGE NOTES
APPENDIX G MISCELLANEOUSG.1CHANGE NOTES G.1.1 REVISION HISTORY
Table G–1: REVISION HISTORY (Sheet 1 of 2)

MANUAL P/N D60 REVISION RELEASE DATE ECO
1601-0089-0.1 1.5x (Beta) 23 August 1999 N/A
1601-0089-A1 2.0x 17 December 1999 N/A
1601-0089-A2 2.0x 14 January 2000 URD-001
1601-0089-A3 2.2x 12 May 2000 URD-002
1601-0089-A4 2.2x 14 June 2000 URD-003
1601-0089-A4a 2.2x 28 June 2000 URD-003a
1601-0089-B1 2.4x 08 September 2000 URD-004
1601-0089-B2 2.4x 03 November 2000 URD-005
1601-0089-B3 2.6x 08 March 2001 URD-006
1601-0089-B4 2.8x 27 September 2001 URD-007
1601-0089-B5 2.9x 03 December 2001 URD-008
1601-0089-B6 2.9x 07 January 2002 URD-009
1601-0089-B7 2.9x 15 March 2002 URD-010
1601-0089-B8 2.6x 27 February 2004 URX-120
1601-0089-C1 3.0x 02 July 2002 URD-010
1601-0089-C2 3.1x 30 August 2002 URD-012
1601-0089-C3 3.0x 18 November 2002 URD-016
1601-0089-C4 3.1x 18 November 2002 URD-017
1601-0089-C5 3.0x 11 February 2003 URD-020
1601-0089-C6 3.1x 11 February 2003 URD-021
1601-0089-D1 3.2x 11 February 2003 URD-023
1601-0089-D2 3.2x 02 June 2003 URX-084
1601-0089-E1 3.3x 01 May 2003 URX-080 G
1601-0089-E2 3.3x 29 May 2003 URX-083
1601-0089-F1 3.4x 10 December 2003 URX-111
1601-0089-F2 3.4x 09 February 2004 URX-115
1601-0089-F3 3.4x 27 February 2004 URX-130
1601-0089-G1 4.0x 23 March 2004 URX-123
1601-0089-G2 4.0x 17 May 2004 URX-136
1601-0089-H1 4.2x 30 June 2004 URX-145
1601-0089-H2 4.2x 23 July 2004 URX-151
1601-0089-J1 4.4x 15 September 2004 URX-156
1601-0089-K1 4.6x 15 February 2005 URX-176
1601-0089-L1 4.8x 05 August 2005 URX-202
1601-0089-M1 4.9x 15 December 2005 URX-208
1601-0089-M2 4.9x 27 February 2006 URX-214
1601-0089-N1 5.0x 31 March 2006 URX-217
1601-0089-N2 5.0x 26 May 2006 URX-220
1601-0089-P1 5.2x 23 October 2006 URX-230
1601-0089-P2 5.2x 24 January 2007 URX-232
1601-0089-R1 5.4x 26 June 2007 URX-242
1601-0089-R2 5.4x 31 August 2007 URX-246
1601-0089-R3 5.4x 17 October 2007 URX-251
1601-0089-S1 5.5x 7 December 2007 URX-253
1601-0089-S2 5.5x 22 February 2008 URX-258
GE Multilin D60 Line Distance Protection System G-1

G.1 CHANGE NOTES APPENDIX G
Table G–1: REVISION HISTORY (Sheet 2 of 2)

MANUAL P/N D60 REVISION RELEASE DATE ECO
1601-0089-S3 5.5x 12 March 2008 URX-260
1601-0089-T1 5.6x 27 June 2008 08-0390
1601-0089-U1 5.7x 29 May 2009 09-0938
1601-0089-U2 5.7x 30 September 2009 09-1165
1601-0089-V1 5.8x 29 May 2010 09-1457
1601-0089-V2 5.8x 04 January 2011 11-2237
1601-0089-W1 5.9x 12 January 2011 11-2227
1601-0089-X1 6.0x 21 December 2011 11-2840
1601-0089-X2 6.0x 5 April 2012 12-3254
1601-0089-Y1 7.0x 30 September 2012 12-3529
1601-0089-Y2 7.0x 11 November 2012 12-3601
1601-0089-Z1 7.1x 30 March 2013 13-0126
1601-0089-Z2 7.1x 22 September 2013 13-0469
G.1.2 CHANGES TO THE D60 MANUAL
Table G–2: MAJOR UPDATES FOR D60 MANUAL REVISION Z2

PAGE PAGE CHANGE DESCRIPTION
(Z1) (Z2)
--- --- Update General revision throughout document
2-16 2-16 Update Updated Phase Distance Operating Time Curve figure and Ground Distance Operating Time
Curve figure
5-108 5-108 Update Updated hysteresis numbers and logic diagrams in section 5.4.7 Phasor Measurement Unit
5-231 5-231 Update Updated Figure 5-122 Negative-Sequence Overvoltage Scheme Logic
G 8- --- Delete Security chapter - Moved content to other parts of manual and deleted the Security chapter
--- 10- Add Added Maintenance chapter, moving module replacement content from chapter 3, adding battery
replacement instructions, and moving battery disposal instructions from beginning of manual
--- F- Add Added appendix on RADIUS server configuration
Table G–3: MAJOR UPDATES FOR D60 MANUAL REVISION Z1

(Y3) (Z1)
--- --- Add Added CPU options U and V to order code tables in chapter 2, a note above Rear Terminal View
figure in chapter 3, and CPU Module Communications Wiring figure in chapter 3
--- --- Add Added Parallel Redundancy Protocol (PRP) to order code tables and specifications in chapter 2,
section 5.2.5d Settings > Product Setup > Communications > Network, section 6.3.1 Actual
Values > Status > PRP, and Appendix B Modbus table and F627 and F628 enumeration tables
1-1 1-1 Add Added General Cautions and Warnings to section 1.1.1
1-5 1-5 Update Revised section 1.3.1 on system requirements, including addition of support for Windows 7 and
Windows Server 2008
2-10 2-10 Update Updated several specifications
5-24 5-24 Add Added section 5.2.5e Routing

5-86 5-86 Update Updated Figures 5-24 and 5-25 Dual Breaker Control Scheme Logic, sheets 1 and 2
5-90 5-90 Update Updated Figure 5-26 Disconnect Switch Scheme Logic
5-321 5-321 Add Reinserted section 5.8.5c Remote Devices: ID of Device for Receiving GSSE/GOOSE Messages,
meaning the Settings > Input/Outputs > Remote Devices settings
G-2 D60 Line Distance Protection System GE Multilin

APPENDIX G G.1 CHANGE NOTES
Table G–4: MAJOR UPDATES FOR D60 MANUAL REVISION Y3

(Y2) (Y3)
-- xi Add Added battery disposal information as chapter 0
5-242 5-242 Update Updated Figure 5-135 Trip Output Scheme Logic (Sheet 1 of 2)
Table G–5: MAJOR UPDATES FOR D60 MANUAL REVISION Y2

(Y1) (Y2)
All All Update Minor changes throughout document
All All Delete Deleted CPU options U and V
1-1 1-1 Update Updated Figure 1-1 Rear Nameplate
3-8 3-8 Update Updated Figure 3-10 Rear Terminal View
5-304 5-304 Add/Update Added and updated Block Scheme Target and Block Scheme Event in section 5.7g Directional
Comparison Blocking
Table G–6: MAJOR UPDATES FOR D60 MANUAL REVISION Y1 (Sheet 1 of 2)

(X2) (Y1)
All All Delete Deleted content pertaining to Ethernet switch
Title Title Update Changed part numbers. Updated address and contact information.
1-1 1-1 Update Updated address and contact information
2- 2- Add Added CPU options T,U, and V to order code table

2- 2- Delete Removed E, G, H, J, S from CPU options from order code tables
2-8 2-8 Delete Deleted 9S, 2S, 2T from replacement module order codes Tables 2-7 and 2-8
2-21 2-21 Update Updated Ethernet fiber table in section 2.2.8 Communications G
3-10 3-10 Update Updated Figure 3-12 Typical Wiring Diagram
3-22 3-22 Update Deleted references to COM 1 RS485 port in section 3.2.9 CPU Communication Ports. Revised
text and Figure 3-24 CPU Module Communications Wiring to include only modules T, U, V in
section 3.2.9a.
5-1 5-1 Update Updated the front panel main menu to include the CyberSentry security menu
5-15 5-15 Update Update Communications main menu to remove the SNTP Protocol submenu
5-16 5-16 Delete Deleted references to COM 1 RS485 port in section 5.2.4b Serial Ports
5-16 5-16 Add Added section 5.2.4c Ethernet Network Topology
5-17 5-17 Update Updated Networks section 5.2.4d to include all three Ethernet ports
5-17 5-17 Update Added 0 as valid number to section 5.2.4e Modbus Protocol section
5-38 5- Delete Deleted Local Time Offset, Daylight Savings Time, DST (start/stop for month/day/hour) from Real
Time Clock menu
5- 5-37 Add Added submenus Precision Time Protocol, SNTP Protocol, and Local Time and Synchronizing
Source settings to Real Time Clock menu
5- 5-38 Add Added new Precision Time Protocol (1588) menu and setting descriptions
5-40 5-40 Update Changed Communication to Real Time Clock in SNTP protocol settings path. Moved SNTP
Protocol menu and settings descriptions to Real Time Clock subsection
5-37 5- Delete Deleted section k) SNTP Protocol and the settings descriptions
5- 5-41 Add Added new section for Local Time menu settings and settings description
5- 5-50 Add Added new PTP Fail menu item to the User-Programmable Self Tests menu
5- 5- Add Added PTP Failure and CLOCK UNSYNCHRONIZED to Flexlogic Operands table
5-91 5-91 Update Updated PMU main menu to add aggregator and control block menu items

G.1 CHANGE NOTES APPENDIX G
Table G–6: MAJOR UPDATES FOR D60 MANUAL REVISION Y1 (Sheet 2 of 2)

(X2) (Y1)
5- 5-91 Add Added UR Synchrophasor Implementation of IEC61850-90-5 to the PMU software option
description
5-91 5-91 Update Updated Figure: Complete Synchrophasor Implementation
5- 5-92 Add Added Figure: N60 Support For Four Logical Device PMU
5-92 5-92 Update Updated Table: Implementation By Model Number
5- 5-93 Add Added Figure: Logical Nodes Supported In Each Logical Device
5- 5-94 Add Added Figure: Data Set Created From User Selected Internal Items
5- 5-95 Add Added Figure: Example Of Aggregator Data Sets
5- 5-95 Add Added Figure: CFG-2 Based Configuration Solution
5- 5-95 Add Added examples for a syncrophasor dataset and the creation of different datasets
5- 5-95 Add Added example for a CFG-2 based configuration
5-97 5-97 Update Updated PMU 1 basic configuration menu to add 37.118 and 90-5 configuration settings
submenus
5- 5-98 Add Added PMU 1 configuration menus for 37.118 and 90-5 with settings descriptions
5-98 5-98 Update Changed PMU 1 Function setting description
5- 5-108 Add Added PMU AGGR 1 configuration menu and setting descriptions
5- 5-91 Add Added new aggregators section with PMU 1 aggregators menu and setting descriptions
5-109 5-109 Update Updated PMU 1 aggregators menu to include 37.118 and 90-5 aggregator configuration
submenus
5- 5-109 Add Added 90-5 AGGR 1 configuration menu and setting descriptions
5- 5-110 Add Added Table 5-11 # Of ASDUs
5- 5-110 Add Added new control block section with IEC 90-5 MSVCB configuration menu and setting
descriptions
5-127 5-127 Add Added new operands for POTT1 to Table 5-11: FlexLogic Operands
5- 5-135 Update Added row for DeltaTime to Table 5-: FlexElement Base Units
G
5-315 5-315 Delete Deleted section 5.8.5c Remote Devices: ID of Device for Receiving GSSE/GOOSE Messages,
meaning the Settings > Input/Outputs > Remote Devices settings
5- 5- Add Added new CyberSentry security section and main menu, local passwords, session settings,
restore defaults, and supervisory subsections to Chapter 5
5- 5- Update Changed main menu for Pilot schemes to add POTT1 and submenu descriptions
6-1 6-1 Update Update Actual Values main menu to include Real Time Clock Synchronization submenu
6- 6-7 Add Added new section for Real Time Clock synchronizing consisting of the menu of settings and the
setting descriptions
6-11 6-11 Delete Deleted section 6.2.19 Ethernet Switch
6- 6-11 Add Added new section 6.2.20 Remaining Connection Status
7- 7-1 Add Added Security command to the Commands main menu

7- 7-3 Add Added Reboot Relay command and description to the Relay Maintenance menu items
7- 7- Add Added Security menu and submenu commands and descriptions to the Command menu
7- 7- Add Added to Minor self-test error message **Bad PTP Signal**
8- 8-4 Add Added new section for CyberSentry software option with overview and security menu subsections
A- A- Add Added FlexAnalog item PTP–IRIG-B Delta to Table A-1: FlexAnalog Data Items
B-8 B-8 Update Updated Modbus memory map table to include port 0 for Modbus slave address, TCP, DNP,
HTTP, TFTP, MMS, and removed references to COM 1 RS485 port
C-23 C-23 Update Updated tables in sections C.6.3 ACSI Services Conformance Statement and C.7.1 Logical
Nodes Table

APPENDIX G G.2 ABBREVIATIONS
G.2ABBREVIATIONS G.2.1 STANDARD ABBREVIATIONS
A..................... Ampere FO...................Fiber Optic

AC .................. Alternating Current FREQ..............Frequency
A/D ................. Analog to Digital FSK.................Frequency-Shift Keying
AE .................. Accidental Energization, Application Entity FTP .................File Transfer Protocol
AMP ............... Ampere FxE .................FlexElement™
ANG ............... Angle FWD................Forward
ANSI............... American National Standards Institute
AR .................. Automatic Reclosure G .....................Generator
ASDU ............. Application-layer Service Data Unit GE...................General Electric
ASYM ............. Asymmetry GND................Ground
AUTO ............. Automatic GNTR..............Generator
AUX................ Auxiliary GOOSE...........General Object Oriented Substation Event
AVG................ Average GPS ................Global Positioning System
BCS................ Best Clock Selector HARM .............Harmonic / Harmonics

BER................ Bit Error Rate HCT ................High Current Time
BF................... Breaker Fail HGF ................High-Impedance Ground Fault (CT)
BFI.................. Breaker Failure Initiate HIZ ..................High-Impedance and Arcing Ground
BKR................ Breaker HMI .................Human-Machine Interface
BLK ................ Block HTTP ..............Hyper Text Transfer Protocol
BLKG.............. Blocking HYB ................Hybrid
BPNT.............. Breakpoint of a characteristic
BRKR ............. Breaker I.......................Instantaneous
I_0...................Zero Sequence current
CAP................ Capacitor I_1...................Positive Sequence current
CC .................. Coupling Capacitor I_2...................Negative Sequence current
CCVT ............. Coupling Capacitor Voltage Transformer IA ....................Phase A current
CFG................ Configure / Configurable IAB ..................Phase A minus B current
.CFG............... Filename extension for oscillography files IB ....................Phase B current
CHK................ Check IBC..................Phase B minus C current
CHNL ............. Channel IC ....................Phase C current
CLS ................ Close ICA..................Phase C minus A current
CLSD.............. Closed ID ....................Identification
CMND ............ Command IED..................Intelligent Electronic Device
CMPRSN........ Comparison IEC..................International Electrotechnical Commission
CO.................. Contact Output IEEE................Institute of Electrical and Electronic Engineers
COM............... Communication IG ....................Ground (not residual) current
COMM............ Communications Igd...................Differential Ground current
COMP ............ Compensated, Comparison IN ....................CT Residual Current (3Io) or Input
CONN............. Connection INC SEQ .........Incomplete Sequence
CONT ............. Continuous, Contact INIT .................Initiate
CO-ORD......... Coordination
CPU................ Central Processing Unit
INST................Instantaneous
INV..................Inverse
G
CRC ............... Cyclic Redundancy Code I/O ...................Input/Output
CRT, CRNT .... Current IOC .................Instantaneous Overcurrent
CSA................ Canadian Standards Association IOV..................Instantaneous Overvoltage
CT .................. Current Transformer IRIG ................Inter-Range Instrumentation Group
CVT ................ Capacitive Voltage Transformer ISO..................International Standards Organization
IUV..................Instantaneous Undervoltage
D/A ................. Digital to Analog
DC (dc)........... Direct Current K0 ...................Zero Sequence Current Compensation
DD .................. Disturbance Detector kA....................kiloAmpere
DFLT .............. Default kV....................kiloVolt
DGNST........... Diagnostics
DI.................... Digital Input LED.................Light Emitting Diode
DIFF ............... Differential LEO.................Line End Open
DIR ................. Directional LFT BLD .........Left Blinder
DISCREP ....... Discrepancy LOOP..............Loopback
DIST ............... Distance LPU.................Line Pickup
DMD ............... Demand LRA.................Locked-Rotor Current
DNP................ Distributed Network Protocol LTC .................Load Tap-Changer
DPO ............... Dropout
DSP................ Digital Signal Processor M.....................Machine
dt .................... Rate of Change mA ..................MilliAmpere
DTT ................ Direct Transfer Trip MAG................Magnitude
DUTT.............. Direct Under-reaching Transfer Trip MAN................Manual / Manually
MAX ................Maximum
ENCRMNT ..... Encroachment MIC .................Model Implementation Conformance
EPRI............... Electric Power Research Institute MIN .................Minimum, Minutes
.EVT ............... Filename extension for event recorder files MMI.................Man Machine Interface
EXT ................ Extension, External MMS ...............Manufacturing Message Specification
MRT ................Minimum Response Time
F ..................... Field MSG................Message
FAIL................ Failure MTA ................Maximum Torque Angle
FD .................. Fault Detector MTR ................Motor
FDH................ Fault Detector high-set MVA ................MegaVolt-Ampere (total 3-phase)
FDL ................ Fault Detector low-set MVA_A............MegaVolt-Ampere (phase A)
FLA................. Full Load Current MVA_B............MegaVolt-Ampere (phase B)

G.2 ABBREVIATIONS APPENDIX G
MVA_C ........... MegaVolt-Ampere (phase C) SAT ................ CT Saturation

MVAR ............. MegaVar (total 3-phase) SBO ............... Select Before Operate
MVAR_A......... MegaVar (phase A) SCADA .......... Supervisory Control and Data Acquisition
MVAR_B......... MegaVar (phase B) SEC ............... Secondary
MVAR_C ........ MegaVar (phase C) SEL ................ Select / Selector / Selection
MVARH .......... MegaVar-Hour SENS ............. Sensitive
MW................. MegaWatt (total 3-phase) SEQ ............... Sequence
MW_A ............ MegaWatt (phase A) SIR................. Source Impedance Ratio
MW_B ............ MegaWatt (phase B) SNTP ............. Simple Network Time Protocol
MW_C ............ MegaWatt (phase C) SRC ............... Source
MWH .............. MegaWatt-Hour SSB................ Single Side Band
SSEL.............. Session Selector
N..................... Neutral STATS............ Statistics
N/A, n/a .......... Not Applicable SUPN............. Supervision
NEG ............... Negative SUPV ............. Supervise / Supervision
NMPLT ........... Nameplate SV .................. Supervision, Service
NOM............... Nominal SYNC............. Synchrocheck
NTR................ Neutral SYNCHCHK... Synchrocheck
O .................... Over T..................... Time, transformer

OC, O/C ......... Overcurrent TC .................. Thermal Capacity
O/P, Op........... Output TCP................ Transmission Control Protocol
OP .................. Operate TCU ............... Thermal Capacity Used
OPER ............. Operate TD MULT........ Time Dial Multiplier
OPERATG ...... Operating TEMP............. Temperature
O/S ................. Operating System TFTP.............. Trivial File Transfer Protocol
OSI ................. Open Systems Interconnect THD ............... Total Harmonic Distortion
OSB................ Out-of-Step Blocking TMR ............... Timer
OUT................ Output TOC ............... Time Overcurrent
OV .................. Overvoltage TOV................ Time Overvoltage
OVERFREQ ... Overfrequency TRANS........... Transient
OVLD ............. Overload TRANSF ........ Transfer
TSEL.............. Transport Selector
P..................... Phase TUC ............... Time Undercurrent
PC .................. Phase Comparison, Personal Computer TUV................ Time Undervoltage
PCNT ............. Percent TX (Tx)........... Transmit, Transmitter
PF................... Power Factor (total 3-phase)
PF_A .............. Power Factor (phase A) U .................... Under
PF_B .............. Power Factor (phase B) UC.................. Undercurrent
PF_C .............. Power Factor (phase C) UCA ............... Utility Communications Architecture
PFLL............... Phase and Frequency Lock Loop UDP ............... User Datagram Protocol
PHS................ Phase UL .................. Underwriters Laboratories
PICS............... Protocol Implementation & Conformance UNBAL........... Unbalance
G Statement
PKP ................ Pickup
PLC ................ Power Line Carrier
UR.................. Universal Relay
URC ............... Universal Recloser Control
.URS .............. Filename extension for settings files
POS................ Positive UV.................. Undervoltage
POTT.............. Permissive Over-reaching Transfer Trip
PRESS ........... Pressure V/Hz ............... Volts per Hertz
PRI ................. Primary V_0 ................ Zero Sequence voltage
PROT ............. Protection V_1 ................ Positive Sequence voltage
PSEL .............. Presentation Selector V_2 ................ Negative Sequence voltage
pu ................... Per Unit VA .................. Phase A voltage
PUIB............... Pickup Current Block VAB ................ Phase A to B voltage
PUIT ............... Pickup Current Trip VAG................ Phase A to Ground voltage
PUSHBTN ...... Pushbutton VARH ............. Var-hour voltage
PUTT.............. Permissive Under-reaching Transfer Trip VB .................. Phase B voltage
PWM .............. Pulse Width Modulated VBA................ Phase B to A voltage
PWR............... Power VBG ............... Phase B to Ground voltage
VC.................. Phase C voltage
QUAD............. Quadrilateral VCA ............... Phase C to A voltage
VCG ............... Phase C to Ground voltage
R..................... Rate, Reverse VF .................. Variable Frequency
RCA................ Reach Characteristic Angle VIBR .............. Vibration
REF ................ Reference VT .................. Voltage Transformer
REM ............... Remote VTFF.............. Voltage Transformer Fuse Failure
REV................ Reverse VTLOS ........... Voltage Transformer Loss Of Signal
RI.................... Reclose Initiate
RIP ................. Reclose In Progress WDG .............. Winding
RGT BLD........ Right Blinder WH................. Watt-hour
ROD ............... Remote Open Detector w/ opt ............. With Option
RST ................ Reset WRT............... With Respect To
RSTR ............. Restrained
RTD ................ Resistance Temperature Detector X .................... Reactance
RTU ................ Remote Terminal Unit XDUCER........ Transducer
RX (Rx) .......... Receive, Receiver XFMR............. Transformer
s ..................... second Z..................... Impedance, Zone

S..................... Sensitive

APPENDIX G G.3 WARRANTY
G.3WARRANTY G.3.1 GE MULTILIN WARRANTY
GE MULTILIN RELAY WARRANTY

GE Multilin warrants each relay it manufactures to be free from defects in material and workman-
ship under normal use and service for a period of 24 months from date of shipment from factory.
In the event of a failure covered by warranty, GE Multilin will undertake to repair or replace the relay
providing the warrantor determined that it is defective and it is returned with all transportation
charges prepaid to an authorized service centre or the factory. Repairs or replacement under war-
ranty will be made without charge.
Warranty shall not apply to any relay which has been subject to misuse, negligence, accident,
incorrect installation or use not in accordance with instructions nor any unit that has been altered
outside a GE Multilin authorized factory outlet.
GE Multilin is not liable for special, indirect or consequential damages or for loss of profit or for
expenses sustained as a result of a relay malfunction, incorrect application or adjustment.
G
For complete text of Warranty (including limitations and disclaimers), refer to GE Multilin Standard
Conditions of Sale.

G.3 WARRANTY APPENDIX G

INDEX
BINARY INPUT POINTS .................................................... E-8

Numerics BINARY OUTPUT POINTS ................................................. E-9
BLOCK DIAGRAM .............................................................. 1-3
10BASE-F BLOCK SETTING ............................................................... 5-5
interface ........................................................................ 3-33 BLOCKING SCHEME
settings ......................................................................... 5-29 application of settings ...................................................... 9-8
FlexLogic operands ...................................................... 5-135
logic ............................................................................ 5-320
settings ............................................................ 5-317, 5-318
A BREAKER ARCING CURRENT
actual values ................................................................. 6-26
ABBREVIATIONS .............................................................. G-5
clearing .................................................................. 5-25, 7-2
AC CURRENT INPUTS ................................... 2-23, 3-10, 5-90
AC VOLTAGE INPUTS .............................................2-24, 3-11
logic ............................................................................ 5-284
ACTIVATING THE RELAY ........................................1-19, 4-27
measurement ............................................................... 5-284
ACTIVE SETTING GROUP ............................................. 5-155
Modbus registers .......................................................... B-15
ACTUAL VALUES
settings ....................................................................... 5-283
maintenance ................................................................. 6-26
specifications ................................................................. 2-20
metering ........................................................................ 6-13
BREAKER CONTROL
product information ........................................................ 6-27
control of 2 breakers ...................................................... 4-24
records ......................................................................... 6-24
description ..................................................................... 4-23
status .............................................................................. 6-4
dual breaker logic ................................................. 5-97, 5-98
ALARM LEDs ................................................................... 5-68
ANSI DEVICE NUMBERS .........................................2-2, 5-110
APPARENT POWER ................................................2-23, 6-18
settings ......................................................................... 5-95
APPLICATION EXAMPLES
BREAKER FAILURE
breaker trip circuit integrity .......................................... 5-279
description ................................................................... 5-218
contact inputs .............................................................. 5-327
determination ............................................................... 5-219
pilot schemes .................................................................. 9-6
sensitive directional power ........................................... 5-238
logic ................................................................. 5-222, 5-223
series compensated lines .......................................8-18, 9-11
main path sequence ..................................................... 5-219
stepped distance scheme ................................................. 9-2
APPROVALS ................................................................... 2-29
settings ............................................................ 5-217, 5-220
ARCHITECTURE ........................................................... 5-131
specifications ................................................................. 2-20
ARCING CURRENT ....................................................... 5-283
BREAKER FLASHOVER
AUTORECLOSE
actual values ................................................................... 6-6
logic ............................................................................ 5-288
description .................................................................. 5-266
FlexLogic operands ..................................................... 5-133
settings ....................................................................... 5-285
logic ....................................................... 5-272, 5-274, 5-275
specifications ................................................................. 2-20
Modbus registers .................................................. B-16, B-41
BREAKER RESTRIKE
sequence .................................................................... 5-276
settings ............................. 5-264, 5-267, 5-268, 5-270, 5-271
logic ............................................................................ 5-291
specifications ................................................................ 2-20
AUXILIARY OVERVOLTAGE
settings ....................................................................... 5-289
BREAKER-AND-A-HALF SCHEME ...................................... 5-6
logic ............................................................................ 5-233
BRIGHTNESS .................................................................. 5-23
Modbus registers ........................................................... B-50
BROKEN CONDUCTOR
settings ....................................................................... 5-233
specifications ................................................................ 2-19
settings ....................................................................... 5-297
AUXILIARY UNDERVOLTAGE
BROKEN CONDUCTOR DETECTION
logic ............................................................................ 5-232
settings ....................................................................... 5-232
specifications ................................................................ 2-19 C
AUXILIARY VOLTAGE CHANNEL ..................................... 3-11
AUXILIARY VOLTAGE METERING ................................... 6-18 C37.94 COMMUNICATIONS ........................... 3-34, 3-36, 3-39
C37.94SM COMMUNICATIONS ........................................ 3-38
CAPACITOR CONTROL
B CAUTIONS ......................................................................... 1-1
CE APPROVALS .............................................................. 2-29
BANKS ............................................................. 5-6, 5-90, 5-91
CHANGES TO D60 MANUAL ............................................. G-2
BATTERY
CHANNEL TESTS ............................................................ 6-10
disposal ........................................................................ 10-4
CHANNELS
failure ............................................................................. 7-8
banks ................................................................... 5-90, 5-91
replace .......................................................................... 10-3
CIRCUIT MONITORING APPLICATIONS ......................... 5-277
BATTERY FAILURE ........................................................... 7-8
GE Multilin D60 Line Distance Protection System i

INDEX
CLEANING ....................................................................... 2-29 CT BANKS

CLEAR RECORDS .................................................... 5-25, 7-2 settings ..........................................................................5-90
CLEAR RELAY RECORDS CT INPUTS ...................................................... 3-11, 5-6, 5-90
Modbus registers ...........................................................B-69 CT WIRING ......................................................................3-11
settings ......................................................................... 5-25 CURRENT BANK ..............................................................5-90
CLOCK CURRENT DIFFERENTIAL
setting date and time ....................................................... 7-2 Modbus registers ........................................................... B-16
settings ......................................................................... 5-56 CURRENT METERING
COMMANDS MENU ........................................................... 7-1 actual values ..................................................................6-16
COMMUNICATIONS Modbus registers ........................................................... B-12
10BASE-F ..................................................................... 5-29 specifications .................................................................2-23
connecting to the UR .............................................. 1-9, 1-15 CURVES
CRC-16 error checking .................................................... B-2 definite time ...................................................... 5-191, 5-226
DNP ....................................................................... 5-34, E-1 FlexCurves ....................................................... 5-102, 5-191
G.703 ............................................................................ 3-29 I2T ............................................................................... 5-191
half duplex...................................................................... B-1 IAC .............................................................................. 5-190
HTTP ............................................................................ 5-53 IEC .............................................................................. 5-189
IEC 60870-5-104 protocol .............................................. 5-54 IEEE ............................................................................ 5-187
IEC 61850 ................................................................... 5-332 inverse time undervoltage ............................................. 5-226
inter-relay communications ............................................. 2-27 types ........................................................................... 5-187
Modbus .................................................. 5-34, 5-55, B-1, B-3
Modbus registers ...........................................................B-26
network ......................................................................... 5-29
overview ........................................................................ 1-18 D
RS232 ........................................................................... 3-21
DATA FORMATS, MODBUS ............................................. B-81
RS485 .................................................................. 3-23, 5-26
DATA LOGGER
settings ...................................... 5-29, 5-34, 5-39, 5-54, 5-55
clearing ...................................................................5-25, 7-2
specifications ........................................................ 2-26, 2-27
Modbus ........................................................................... B-7
UCA/MMS ................................................................... 5-334
web server..................................................................... 5-53
settings ..........................................................................5-64
COMPATIBILITY ................................................................ 1-3
specifications .................................................................2-22
COMPENSATED OVERVOLTAGE
via COMTRADE .............................................................. B-6
DATE ................................................................................ 7-2
settings ....................................................................... 5-234
DCMA INPUTS .................................................................6-23
specifications................................................................. 2-19
COMTRADE ............................................................... B-6, B-7
settings ........................................................................ 5-343
CONDUCTED RFI ............................................................ 2-28
specifications .................................................................2-24
CONTACT INPUTS
DCMA OUTPUTS
actual values ................................................................... 6-4
description .....................................................................3-20
dry connections ............................................................. 3-17
settings ........................................................................ 5-346
Modbus registers ............................... B-11, B-18, B-63, B-65
specifications .................................................................2-26
settings ....................................................................... 5-326
DEFINITE TIME CURVE ...................................... 5-191, 5-226
specifications................................................................. 2-24
DESIGN ............................................................................ 1-3
thresholds ................................................................... 5-326
DEVICE ID ..................................................................... 5-332
wet connections ............................................................. 3-17
DEVICE PROFILE DOCUMENT .......................................... E-1
CONTACT OUTPUTS
DIELECTRIC STRENGTH .................................................. 3-9
actual values ................................................................... 6-5
DIGITAL COUNTERS
actual values ................................................................... 6-7
Modbus registers .........................................B-11, B-18, B-76
settings ....................................................................... 5-329
logic ............................................................................ 5-281
CONTROL ELEMENTS ................................................... 5-240
CONTROL POWER
settings ........................................................................ 5-280
description..................................................................... 3-10
DIGITAL ELEMENTS
specifications................................................................. 2-25
application example ...................................................... 5-278
CONTROL PUSHBUTTONS
logic ............................................................................ 5-277
settings ......................................................................... 5-69
settings ........................................................................ 5-277
specifications................................................................. 2-22
DIGITAL OUTPUTS
COUNTERS
see entry for CONTACT OUTPUTS
actual values ................................................................... 6-7
DIMENSIONS ............................................................. 3-1, 3-2
settings ....................................................................... 5-280
DIRECT DEVICES
CRC ALARM .................................................................... 5-85
actual values ..................................................................6-10
CRC-16 ALGORITHM ........................................................ B-2
CRITICAL FAILURE RELAY ....................................... 2-25, 3-9
settings ........................................................................ 5-336
CSA APPROVAL .............................................................. 2-29
ii D60 Line Distance Protection System GE Multilin

INDEX
DIRECT I/O DYNAMIC REACH CONTROL ........................................... 8-19

see also DIRECT INPUTS and DIRECT OUTPUTS
application example ........................................... 5-337, 5-338
configuration examples ........................ 5-79, 5-82, 5-85, 5-86
settings ............................................. 5-79, 5-85, 5-86, 5-336 E
DIRECT INPUTS
EGD PROTOCOL
actual values ................................................................... 6-9
actual values ................................................................. 6-26
ELECTROSTATIC DISCHARGE ........................................ 2-28
clearing counters ............................................................. 7-2
ELEMENTS ........................................................................ 5-4
ENERGY METERING
Modbus registers ................................ B-11, B-21, B-54, B-70
actual values ................................................................. 6-19
settings ....................................................................... 5-336
specifications ................................................................ 2-24
specifications ................................................................. 2-23
DIRECT INPUTS/OUTPUTS
ENERGY METERING, CLEARING ..................................... 5-25
error messages ............................................................... 7-8
ENERVISTA UR SETUP
DIRECT OUTPUTS
creating a site list ............................................................ 4-1
event recorder ................................................................. 4-2
firmware upgrades ........................................................... 4-2
Modbus registers ................................ B-11, B-54, B-69, B-70
installation ....................................................................... 1-6
settings ....................................................................... 5-336
introduction ..................................................................... 4-1
DIRECT UNDERREACH TRANSER TRIP
oscillography ................................................................... 4-2
see entry for DUTT
overview .......................................................................... 4-1
DIRECTIONAL CHARACTERISTIC ..................................... 8-4
requirements ................................................................... 1-6
DIRECTIONAL COMPARISON BLOCKING
EQUATIONS
definite time curve ............................................ 5-191, 5-226
see BLOCKING SCHEME
FlexCurve .................................................................... 5-191
DIRECTIONAL COMPARISON UNBLOCKING
I²t curves ..................................................................... 5-191
see UNBLOCKING SCHEME
IAC curves ................................................................... 5-190
DIRECTIONAL OVERCURRENT
IEC curves ................................................................... 5-189
see PHASE, GROUND, and NEUTRAL DIRECTIONAL entries
IEEE curves ................................................................. 5-187
DIRECTIONAL POLARIZATION ...................................... 5-196
EQUIPMENT MISMATCH ERROR ....................................... 7-7
DISCONNECT SWITCH
ETHERNET
actual values ................................................................... 6-8
logic ............................................................................ 5-101
configuration .................................................................... 1-9
error messages ................................................................ 7-9
settings ......................................................................... 5-99
DISPLAY ........................................................ 1-18, 4-23, 5-23
quick connect ................................................................ 1-10
DISTANCE
settings ......................................................................... 5-29
analysis of elements ........................................................ 8-7
EVENT CAUSE INDICATORS .................................. 4-15, 4-16
characteristics ................................................................. 8-2
EVENT RECORDER
ground ................................................................ 2-17, 5-168
actual values ................................................................. 6-24
mho characteristic ............................................. 5-161, 5-163
clearing .................................................................. 5-25, 7-2
Modbus .......................................................................... B-7
phase .................................................................. 2-16, 5-159
quad characteristic ................................. 5-162, 5-163, 5-170
specifications ................................................................. 2-22
settings ....................................................................... 5-158
via EnerVista software ..................................................... 4-2
stepped distance ............................................................. 9-2
EVENTS SETTING ............................................................. 5-5
DISTURBANCE DETECTOR
EXCEPTION RESPONSES ................................................ B-5
internal ......................................................................... 5-93
DNA-1 BIT PAIR ............................................................ 5-334
DNP COMMUNICATIONS F
binary counters ............................................................. E-10
binary input points ........................................................... E-8 F485 ................................................................................ 1-18
binary output points ......................................................... E-9 FACEPLATE ............................................................... 3-1, 3-2
control relay output blocks ............................................... E-9 FACEPLATE PANELS ............................................. 4-13, 4-23
device profile document ................................................... E-1 FACTORY DEFAULT RESET .............................................. 5-8
frozen counters ............................................................. E-10 FAST FORM-C RELAY ..................................................... 2-25
implementation table ....................................................... E-4 FAST TRANSIENT TESTING ............................................ 2-28
Modbus registers ........................................................... B-26 FAULT LOCATOR
settings ......................................................................... 5-34 logic .............................................................................. 8-38
DUPLEX, HALF .................................................................. B-1 Modbus registers .......................................................... B-15
DUTT operation ....................................................................... 8-36
application of settings ...................................................... 9-6 specifications ................................................................. 2-22
logic ............................................................................ 5-304
settings ....................................................................... 5-302
GE Multilin D60 Line Distance Protection System iii

INDEX
FAULT REPORT FREQUENCY METERING

actual values ................................................................. 6-24 actual values ..................................................................6-19
clearing .................................................................. 5-25, 7-2 Modbus registers ........................................................... B-14
Modbus .......................................................................... B-7 settings ..........................................................................5-92
Modbus registers ..................................................B-18, B-28 specifications .................................................................2-23
settings ......................................................................... 5-60 FREQUENCY RATE OF CHANGE
FAULT REPORTS FlexLogic operands ...................................................... 5-135
Modbus registers ...........................................................B-53 Modbus registers .................................................. B-12, B-58
FAULT TYPE ................................................................... 8-36 settings ........................................................................ 5-258
FAX NUMBERS .................................................................. 1-2 FREQUENCY TRACKING ........................................ 5-92, 6-20
FEATURES ........................................................................ 2-1 FREQUENCY, NOMINAL ..................................................5-91
Fiber ................................................................................ 3-27 FUNCTION SETTING ......................................................... 5-5
FIRMWARE REVISION ..................................................... 6-27 FUSE ...............................................................................2-25
FIRMWARE UPGRADES .................................................... 4-2 FUSE FAILURE
FLASH MESSAGES ......................................................... 5-23 see VT FUSE FAILURE
FLEX STATE PARAMETERS
actual values .......................................................... 6-8, 6-20
Modbus registers ..................................................B-18, B-51
settings ......................................................................... 5-76 G
specifications................................................................. 2-21
G.703 .................................................... 3-28, 3-29, 3-30, 3-33
FLEXCURVES
GE TYPE IAC CURVES .................................................. 5-190
equation ...................................................................... 5-191
GROUND CURRENT METERING ......................................6-17
GROUND DIRECTIONAL SUPERVISION ......................... 5-175
settings ....................................................................... 5-102
GROUND DISTANCE
specifications................................................................. 2-21
application of settings ...................................................... 9-3
table ............................................................................ 5-102
FLEXELEMENTS
actual values ................................................................. 6-21
op scheme ...................................................................5-173
direction ...................................................................... 5-152
scheme logic ..................................................... 5-174, 5-175
settings ........................................................................ 5-168
hysteresis .................................................................... 5-152
specifications .................................................................2-17
GROUND IOC
pickup ......................................................................... 5-152
scheme logic ............................................................... 5-151
logic ............................................................................ 5-209
settings .................................................. 5-150, 5-151, 5-153
specifications................................................................. 2-21
settings ........................................................................ 5-209
FLEXLOGIC
GROUND TIME OVERCURRENT
editing with EnerVista UR Setup ....................................... 4-2
see entry for GROUND TOC
equation editor ............................................................ 5-149
GROUND TOC
error messages ................................................................ 7-7
evaluation.................................................................... 5-144
logic ............................................................................ 5-208
example ............................................................5-131, 5-145
example equation ........................................................ 5-243
settings ........................................................................ 5-208
gate characteristics ...................................................... 5-143
specifications .................................................................2-17
locking equation entries ................................................... 4-8
GROUPED ELEMENTS ................................................... 5-155
locking to a serial number ................................................ 4-9
GSSE ................................................. 5-333, 5-334, 5-335, 6-7
operands ...........................................................5-132, 5-133
operators ..................................................................... 5-144
rules ............................................................................ 5-144 H
security ........................................................................... 4-8
specifications................................................................. 2-21 HALF-DUPLEX .................................................................. B-1
timers .......................................................................... 5-149 HTTP PROTOCOL ............................................................5-53
worksheet .................................................................... 5-146 HYBRID PERMISSIVE OVERREACH TRANSFER TRIP
FLEXLOGIC EQUATION EDITOR ................................... 5-149 see entry for HYBRID POTT
FLEXLOGIC TIMERS HYBRID POTT
Modbus registers ...........................................................B-34 application of settings ...................................................... 9-7
settings ....................................................................... 5-150 FlexLogic operands ...................................................... 5-136
FORCE CONTACT INPUTS ............................................ 5-350 logic ............................................................................ 5-316
FORCE CONTACT OUTPUTS ......................................... 5-351 settings ...................................................5-313, 5-315, 5-316
FORCE TRIGGER ............................................................ 6-25 HYRBRID POTT
FORM-A RELAY Modbus registers ........................................................... B-40
high impedance circuits .................................................. 3-13
outputs .........................................................3-12, 3-13, 3-17
specifications................................................................. 2-25
FORM-C RELAY
I
outputs ................................................................. 3-12, 3-17 I2T CURVES .................................................................. 5-191
specifications................................................................. 2-25 IAC CURVES .................................................................. 5-190
iv D60 Line Distance Protection System GE Multilin

INDEX
IEC 60870-5-104 PROTOCOL

interoperability document .................................................D-1 L
settings ......................................................................... 5-54
IEC 61850 GOOSE ANALOGS LAMPTEST ........................................................................ 7-3
settings ....................................................................... 5-341 LANGUAGE ..................................................................... 5-23
IEC 61850 GOOSE UINTEGERS LASER MODULE .............................................................. 3-27
settings ....................................................................... 5-342 LATCHING OUTPUTS
IEC 61850 PROTOCOL application example .......................................... 5-330, 5-331
device ID ..................................................................... 5-333 error messages ................................................................ 7-9
DNA2 assignments ...................................................... 5-335 settings ....................................................................... 5-329
error messages ............................................................. 7-10 specifications ................................................................. 2-25
Modbus registers ..... B-58, B-59, B-60, B-61, B-62, B-63, B-74 LED INDICATORS ......................... 4-14, 4-15, 4-16, 4-22, 5-68
remote inputs .............................................................. 5-333 LED TEST
settings ......................................................................... 5-39 FlexLogic operand ....................................................... 5-142
UserSt-1 bit pair .......................................................... 5-335 settings ......................................................................... 5-66
IEC CURVES ................................................................. 5-189 specifications ................................................................. 2-21
IED SETUP ........................................................................ 1-6 LINE
IEEE C37.94 COMMUNICATIONS ................... 3-34, 3-36, 3-39 pickup ......................................................................... 5-156
IEEE CURVES ............................................................... 5-187 LINE PICKUP
IMPORTANT CONCEPTS ................................................... 1-5 FlexLogic operands ...................................................... 5-136
IN SERVICE INDICATOR .......................................... 1-19, 7-6 logic ............................................................................ 5-157
INCOMPATIBLE HARDWARE ERROR ................................ 7-7 Modbus registers .......................................................... B-45
INPUTS settings ....................................................................... 5-156
AC current .............................................................2-23, 5-90 specifications ................................................................. 2-17
AC voltage ............................................................2-24, 5-91 LINK POWER BUDGET .................................................... 2-27
contact inputs ........................................... 2-24, 5-326, 5-350 LOAD ENCROACHMENT
dcmA inputs ..........................................................2-24, 3-20 FlexLogic operands ...................................................... 5-136
direct inputs .................................................................. 2-24 Modbus registers .......................................................... B-38
IRIG-B ..................................................................2-24, 3-24 settings ............................................................ 5-185, 5-186
remote inputs .................................2-24, 5-332, 5-333, 5-334 specifications ................................................................. 2-21
RTD inputs ............................................................2-24, 3-20 LOGIC GATES ............................................................... 5-144
virtual ......................................................................... 5-328 LOST PASSWORD ............................................................. 5-8
INSPECTION CHECKLIST ................................................. 1-2
INSTALLATION
communications ............................................................ 3-22
CT inputs ..............................................................3-10, 3-11 M
RS485 ........................................................................... 3-23
MAINTENANCE
settings ......................................................................... 5-87
alert to replace battery ..................................................... 7-8
INSTANTANEOUS OVERCURRENT
battery ........................................................................... 10-3
see PHASE, GROUND, and NEUTRAL IOC entries
module replacement ....................................................... 10-1
INTER-RELAY COMMUNICATIONS .................................. 2-27
MAINTENANCE COMMANDS ............................................. 7-3
INTRODUCTION ................................................................ 1-3
MANUFACTURING DATE ................................................. 6-27
INVERSE TIME UNDERVOLTAGE .................................. 5-227
MEMORY MAP DATA FORMATS ..................................... B-81
IOC
MEMORY POLARIZATION ........................................... 8-6, 9-1
see PHASE, GROUND, and NEUTRAL IOC entries
MEMORY VOLTAGE LOGIC ........................................... 5-159
IP ADDRESS ................................................................... 5-29
MENU HIERARCHY ................................................. 1-19, 4-25
IRIG-B
MENU NAVIGATION ....................................... 1-19, 4-24, 4-25
connection .................................................................... 3-24
METERING
error messages ........................................................ 7-8, 7-9
conventions .......................................................... 6-13, 6-14
specifications ................................................................ 2-24
current ........................................................................... 2-23
ISO-9000 REGISTRATION ............................................... 2-29
frequency ...................................................................... 2-23
power ............................................................................ 2-23
voltage .......................................................................... 2-23
K METERING CONVENTIONS ............................................. 6-14
MHO DISTANCE CHARACTERISTIC ....................... 5-161, 8-2
KEYPAD ..................................................................1-19, 4-23
GE Multilin D60 Line Distance Protection System v

INDEX
MODBUS NEGATIVE SEQUENCE TOC

data logger .............................................................. B-6, B-7 FlexLogic operands ...................................................... 5-136
event recorder ................................................................ B-7 logic ............................................................................ 5-211
exception responses ....................................................... B-5 Modbus registers ........................................................... B-37
execute operation ........................................................... B-4 settings ........................................................................ 5-211
fault report ...................................................................... B-7 specifications .................................................................2-18
flex state parameters ..................................................... 5-77 NEUTRAL DIRECTIONAL OC
function code 03/04h ....................................................... B-3 Modbus registers ........................................................... B-45
function code 05h ........................................................... B-4 NEUTRAL DIRECTIONAL OVERCURRENT
function code 06h ........................................................... B-4 FlexLogic operands ...................................................... 5-136
function code 10h ........................................................... B-5 logic ............................................................................ 5-204
introduction .................................................................... B-1 polarization .................................................................. 5-202
memory map data formats ..............................................B-81 settings ........................................................................ 5-200
obtaining files ................................................................. B-6 specifications .................................................................2-18
oscillography .................................................................. B-6 NEUTRAL INSTANTANEOUS OVERCURRENT
passwords ...................................................................... B-7 see entry for NEUTRAL IOC
read/write settings/actual values ...................................... B-3 NEUTRAL IOC
settings ................................................................ 5-34, 5-55 FlexLogic operands ...................................................... 5-136
store multiple settings ..................................................... B-5 logic ............................................................................ 5-199
store single setting ......................................................... B-4 Modbus registers ........................................................... B-35
supported function codes ................................................ B-3 settings ........................................................................ 5-199
user map ..................................................... 5-55, B-11, B-31 specifications .................................................................2-18
MODEL INFORMATION .................................................... 6-27 NEUTRAL OVERVOLTAGE
MODIFICATION FILE NUMBER ........................................ 6-27 FlexLogic operands ...................................................... 5-136
MODULE FAILURE ERROR ................................................ 7-7 logic ............................................................................ 5-230
MODULES Modbus registers ........................................................... B-49
communications ............................................................. 3-22 settings ........................................................................ 5-230
CT ................................................................................. 3-11 specifications .................................................................2-19
CT/VT .................................................................... 3-10, 5-6 NEUTRAL TIME OVERCURRENT
direct inputs/outputs ...................................................... 3-27 see entry for NEUTRAL TOC
insertion ........................................................................ 10-1 NEUTRAL TOC
order codes ................................................................... 2-14 FlexLogic operands ...................................................... 5-136
power supply ................................................................... 3-9 logic ............................................................................ 5-198
transducer I/O ............................................................... 3-20 Modbus registers ........................................................... B-35
VT ................................................................................. 3-11 settings ........................................................................ 5-198
withdrawal ..................................................................... 10-1 specifications .................................................................2-17
MONITORING ELEMENTS ............................................. 5-282 NON-VOLATILE LATCHES
MOUNTING ................................................................. 3-1, 3-2 FlexLogic operands ...................................................... 5-136
settings ........................................................................ 5-154
specifications .................................................................2-21
N
NAMEPLATE ...................................................................... 1-2
NEGATIVE SEQUENCE DIRECTIONAL OC O
NEGATIVE SEQUENCE DIRECTIONAL OVERCURRENT ONE SHOTS ...................................................................5-144
characteristics ............................................................. 5-215 OPEN POLE DETECTOR
FlexLogic operands ...................................................... 5-136 FlexLogic operands ...................................................... 5-137
logic ............................................................................ 5-216 logic ................................................................. 5-296, 5-297
settings .............................................................5-213, 5-216 Modbus registers ........................................................... B-39
specifications................................................................. 2-18 settings ........................................................................ 5-294
NEGATIVE SEQUENCE IOC specifications .................................................................2-21
FlexLogic operands ...................................................... 5-136 OPERATING TEMPERATURE ...........................................2-27
logic ............................................................................ 5-212 OPERATING TIMES .........................................................2-16
Modbus registers ...........................................................B-37 ORDER CODES ........................ 2-8, 2-9, 2-11, 2-12, 6-27, 7-3
settings ....................................................................... 5-212 ORDER CODES, UPDATING ............................................. 7-3
specifications................................................................. 2-18 ORDERING ........................................ 2-7, 2-8, 2-9, 2-11, 2-12
NEGATIVE SEQUENCE OVERVOLTAGE OSCILLATORY TRANSIENT TESTING ..............................2-28
FlexLogic operands ...................................................... 5-136 OSCILLOGRAPHY
logic ............................................................................ 5-231 actual values ..................................................................6-25
Modbus registers ...........................................................B-37 clearing ...................................................................5-25, 7-2
settings ....................................................................... 5-231 Modbus ........................................................................... B-6
specifications................................................................. 2-19 Modbus registers .................................................. B-18, B-28
settings ..........................................................................5-62
specifications .................................................................2-22
via COMTRADE .............................................................. B-6
via EnerVista software ..................................................... 4-2
vi D60 Line Distance Protection System GE Multilin

INDEX
OST ...................................................................... 2-20, 5-178 PHASE CURRENT METERING ......................................... 6-16

OUT-OF-STEP TRIPPING ...................................... 2-20, 5-178 PHASE DIRECTIONAL OC
OUTPUTS Modbus registers .......................................................... B-45
contact outputs ............................................................ 5-329 PHASE DIRECTIONAL OVERCURRENT
control power ................................................................ 2-25 FlexLogic operands ...................................................... 5-137
critical failure relay ........................................................ 2-25 logic ............................................................................ 5-197
Fast Form-C relay ......................................................... 2-25 phase A polarization .................................................... 5-195
Form-A relay ....................................... 2-25, 3-12, 3-13, 3-17 settings ............................................................ 5-195, 5-196
Form-C relay ................................................ 2-25, 3-12, 3-17 specifications ................................................................. 2-18
latching outputs ................................................... 2-25, 5-329 PHASE DISTANCE
remote outputs .................................................. 5-334, 5-335 application of settings ...................................................... 9-2
virtual outputs ............................................................. 5-331 FlexLogic operands ...................................................... 5-137
OVERCURRENT CURVE TYPES .................................... 5-187 logic ............................................................................ 5-167
OVERCURRENT CURVES Modbus registers .......................................................... B-43
definite time ................................................................ 5-191 op scheme ................................................................... 5-166
FlexCurves .................................................................. 5-191 settings ....................................................................... 5-159
I2T .............................................................................. 5-191 specifications ................................................................. 2-16
IAC ............................................................................. 5-190 PHASE INSTANTANEOUS OVERCURRENT
IEC ............................................................................. 5-189 see entry for PHASE IOC
IEEE ........................................................................... 5-187 PHASE IOC
OVERFREQUENCY FlexLogic operands ...................................................... 5-137
FlexLogic operands ..................................................... 5-137 logic ............................................................................ 5-194
logic ............................................................................ 5-257 Modbus registers .......................................................... B-35
settings ....................................................................... 5-257 specifications ................................................................. 2-18
specifications ................................................................ 2-19 PHASE MEASUREMENT UNIT
OVERFRQUENCY see entry for SYNCHROPHASOR
Modbus registers ........................................................... B-37 PHASE OVERVOLTAGE
OVERVOLTAGE FlexLogic operands ...................................................... 5-138
auxiliary .............................................................. 2-19, 5-233 logic ............................................................................ 5-229
compensated ............................................................... 5-234 Modbus registers .......................................................... B-42
negative sequence ...................................................... 5-231 settings ....................................................................... 5-229
negative-sequence ........................................................ 2-19 specifications ................................................................. 2-19
neutral ................................................................ 2-19, 5-230 PHASE ROTATION .......................................................... 5-92
phase .................................................................. 2-19, 5-229 PHASE SELECT
PHASE TIME OVERCURRENT
see entry for PHASE TOC
P PHASE TOC
PANEL CUTOUT ......................................................... 3-1, 3-2
logic ............................................................................ 5-193
PARALLEL REDUNDANCY PROTOCOL
actual values ................................................................. 6-11
settings ....................................................................... 5-192
explained ...................................................................... 5-30
specifications ................................................................. 2-17
settings ......................................................................... 5-29
PHASE UNDERVOLTAGE
specifications ................................................................ 2-26
PARITY ........................................................................... 5-26
logic ............................................................................ 5-228
PASSWORD SECURITY .................................................. 5-10
settings ....................................................................... 5-228
PASSWORDS
specifications ................................................................. 2-19
bypass authentication .................................................... 5-21
PHASOR ESTIMATION ....................................................... 8-1
changing ....................................................................... 4-28
PHASOR MEASUREMENT UNIT
for settings templates ...................................................... 4-5
actual values ................................................................. 6-25
lost password .................................................................. 5-8
PILOT SCHEMES
Modbus ........................................................................... B-7
application of settings ...................................................... 9-6
Modbus registers ......................................... B-15, B-25, B-26
blocking ....................................................................... 5-317
overview ....................................................................... 1-20
directional comparison blocking .................................... 5-317
security ........................................................................... 2-4
directional comparison unblocking ................................ 5-321
settings ........................................................................... 2-3
DUTT .......................................................................... 5-302
PC SOFTWARE
hybrid POTT ................................................................ 5-313
see entry for ENERVISTA UR SETUP
POTT ............................................................... 5-307, 5-311
PERMISSIVE FUNCTIONS ............................................. 5-226
PUTT ........................................................................... 5-305
PERMISSIVE OVERREACH TRANSFER TRIP
specifications ................................................................. 2-20
see entry for POTT
unblocking ................................................................... 5-321
PERMISSIVE UNDERREACH TRANSFER TRIP
PMU
see entry for PUTT
see entry for SYNCHROPHASOR
PER-UNIT QUANTITY ........................................................ 5-4
PHASE ANGLE METERING .............................................. 6-14
GE Multilin D60 Line Distance Protection System vii

INDEX
POTT RECLOSING
application of settings ...................................................... 9-6 description ...................................................................5-265
FlexLogic operands ...................................................... 5-139 logic .......................................................5-272, 5-274, 5-275
hybrid POTT ................................................................ 5-313 sequence ..................................................................... 5-276
logic ..................................................................5-310, 5-312 settings ............................. 5-264, 5-267, 5-268, 5-270, 5-271
Modbus registers ..................................................B-57, B-58 REDUNDANCY
settings ....................................... 5-307, 5-308, 5-309, 5-311 PRP actual values ..........................................................6-11
POWER METERING PRP explained ...............................................................5-30
Modbus registers ...........................................................B-14 settings ..........................................................................5-29
specifications................................................................. 2-23 specifications .................................................................2-26
values ........................................................................... 6-18 RELAY ACTIVATION ........................................................4-27
POWER SUPPLY RELAY ARCHITECTURE ................................................ 5-131
description....................................................................... 3-9 RELAY MAINTENANCE ..................................................... 7-3
low range ...................................................................... 2-24 RELAY NAME ...................................................................5-88
specifications................................................................. 2-24 RELAY NOT PROGRAMMED ............................................1-19
POWER SWING BLOCKING .................................. 2-20, 5-178 REMOTE DEVICES
POWER SWING DETECT actual values ................................................................... 6-6
FlexLogic operands ...................................................... 5-139 device ID ..................................................................... 5-333
logic ..................................................................5-183, 5-184 error messages ..............................................................7-10
Modbus registers ...........................................................B-38 FlexLogic operands ...................................................... 5-142
settings .............................................................5-176, 5-180 Modbus registers ................................ B-11, B-18, B-71, B-75
specifications................................................................. 2-20 settings ........................................................................ 5-332
POWER SYSTEM statistics ......................................................................... 6-7
Modbus registers ...........................................................B-30 REMOTE DPS INPUTS
PREFERENCES actual values ................................................................... 6-5
Modbus registers ...........................................................B-26 settings ........................................................................ 5-334
PROCESS BUS REMOTE INPUTS
overview ........................................................................ 3-11 actual values ................................................................... 6-4
PRODUCT INFORMATION ........................................ 6-27, B-9 FlexLogic operands ...................................................... 5-142
PRODUCT SETUP .................................................... 5-8, 5-19 Modbus registers ......................................... B-11, B-18, B-72
PRODUCTION TESTS ...................................................... 2-28 settings ........................................................................ 5-333
PROTECTION ELEMENTS ................................................. 5-4 specifications .................................................................2-24
PRP REMOTE OUTPUTS
actual values ................................................................. 6-11 DNA-1 bit pair .............................................................. 5-334
explained....................................................................... 5-30 Modbus registers ........................................................... B-73
settings ......................................................................... 5-29 UserSt-1 bit pair ........................................................... 5-335
specifications................................................................. 2-26 REPLACEMENT MODULES ..................................... 2-14, 2-15
PU QUANTITY ................................................................... 5-4 REQUIREMENTS FOR INSTALLATION .............................. 1-6
PUSHBUTTONS, USER-PROGRAMMABLE RESETTING ................................................. 5-8, 5-142, 5-335
see USER-PROGRAMMABLE PUSHBUTTONS REVISION HISTORY ......................................................... G-1
PUTT RF IMMUNITY ..................................................................2-28
application of settings ...................................................... 9-6 RFI, CONDUCTED ............................................................2-28
FlexLogic operands ...................................................... 5-139 RMS CURRENT ................................................................2-23
logic ............................................................................ 5-306 RMS VOLTAGE ................................................................2-23
Modbus registers ...........................................................B-40 RS232
settings ....................................................................... 5-305 configuration ..................................................................1-10
specifications .................................................................2-26
wiring .............................................................................3-21
RS422
Q configuration ..................................................................3-31
timing ............................................................................3-32
QUAD DISTANCE CHARACTERISTIC 5-162, 5-163, 5-170, 8-5,
two-channel application ..................................................3-31
8-6
with fiber interface ..........................................................3-33
RS485
description .....................................................................3-23
R specifications .................................................................2-26
RTD INPUTS
REACTIVE POWER ................................................. 2-23, 6-18 actual values ..................................................................6-23
REAL POWER ......................................................... 2-23, 6-18 Modbus registers .................................................. B-20, B-33
REAL TIME CLOCK settings ........................................................................ 5-344
Modbus registers ...........................................................B-28 specifications .................................................................2-24
settings ......................................................................... 5-56
REAR TERMINAL ASSIGNMENTS ...................................... 3-7
RECLOSER CURVES ...........................................5-105, 5-191
S
SALES OFFICE ................................................................. 1-2
SBO .................................................................................5-52
viii D60 Line Distance Protection System GE Multilin

INDEX
SCAN OPERATION ............................................................ 1-4 STEPPED DISTANCE SCHEME .......................................... 9-2

SELECT BEFORE OPERATE ........................................... 5-52 STORAGE TEMPERATURE .............................................. 2-27
SELECTOR SWITCH SUB-HARMONIC STATOR GROUND FAULT
actual values ................................................................... 6-7 FlexLogic operands ...................................................... 5-140
application example ..................................................... 5-248 SUMMATOR
FlexLogic operands ..................................................... 5-139 Modbus registers .......................................................... B-50
logic ............................................................................ 5-249 SURGE IMMUNITY ........................................................... 2-28
Modbus registers ........................................................... B-56 SYMMETRICAL COMPONENTS METERING ..................... 6-14
settings ....................................................................... 5-244 SYNCHROCHECK
specifications ................................................................ 2-22 actual values ............................................... 6-10, 6-20, 6-21
timing ................................................................ 5-247, 5-248 FlexLogic operands ...................................................... 5-140
Self-test errors ................................................................. 7-11 logic ............................................................................ 5-263
SELF-TESTS Modbus registers ................................................. B-16, B-79
description ...................................................................... 7-6 settings ............................................................ 5-260, 5-261
error messages ............................................................... 7-8 specifications ................................................................. 2-20
FlexLogic operands ..................................................... 5-143 SYNCHROPHASORS
Modbus registers ............................................................. B-9 actual values ........................................................ 6-22, 6-23
SENSITIVE DIRECTIONAL POWER clearing PMU records ....................................................... 7-2
actual values ................................................................. 6-20 commands ................................................................ 7-3, 7-5
characteristic ............................................................... 5-238 FlexLogic operands ........................................... 5-137, 5-138
FlexLogic operands ..................................................... 5-135 phase measurement unit triggering ............................... 5-120
logic ............................................................................ 5-239 phasor measurement configuration5-115, 5-116, 5-117, 5-118,
Modbus registers .................................................. B-12, B-38 5-127, 5-128, 5-129
settings ............................................................. 5-237, 5-239 phasor measurement unit .................................. 5-109, 5-114
SERIAL NUMBER ............................................................ 6-27 phasor measurement unit calibration ............................ 5-119
SERIAL PORTS phasor measurement unit recording .............................. 5-127
settings ......................................................................... 5-26 test values ................................................................... 5-352
SERIES COMPENSATED LINES ..............................8-18, 9-11 SYSTEM FREQUENCY ..................................................... 5-91
SETTING GROUPS ................. 5-139, 5-155, 5-242, B-36, B-37 SYSTEM REQUIREMENTS ................................................. 1-6
SETTINGS TEMPLATES SYSTEM SETUP .............................................................. 5-90
description ...................................................................... 4-4
editing ............................................................................. 4-4
enabling .......................................................................... 4-4
Modbus registers ........................................................... B-80 T
password protection ........................................................ 4-5
TARGET MESSAGES ......................................................... 7-6
removing ......................................................................... 4-7
TARGET SETTING ............................................................. 5-5
viewing ........................................................................... 4-6
TARGETS MENU ............................................................... 7-6
SETTINGS, CHANGING ................................................... 4-26
TCP PORT NUMBER ........................................................ 5-53
SIGNAL SOURCES
TELEPROTECTION
description ...................................................................... 5-5
actual values ................................................................... 6-5
metering ........................................................................ 6-16
settings ......................................................................... 5-93
SIGNAL TYPES ................................................................. 1-3
logic ............................................................................ 5-341
SINGLE LINE DIAGRAM ............................................. 2-1, 2-2
SITE LIST, CREATING ....................................................... 4-1
overview ...................................................................... 5-339
SNTP PROTOCOL
settings .................................................... 5-87, 5-339, 5-340
accuracy ....................................................................... 2-26
specifications ................................................................. 2-24
error messages ............................................................... 7-9
TEMPERATURE MONITOR ................................... 5-143, 7-10
TERMINALS ....................................................................... 3-7
settings ......................................................................... 5-59
TESTING
SOFTWARE
force contact inputs ...................................................... 5-350
installation ...................................................................... 1-6
force contact outputs .................................................... 5-351
see entry for ENERVISTA UR SETUP
lamp test ......................................................................... 7-3
SOFTWARE ARCHITECTURE ............................................ 1-5
self-test error messages ...................................................7-6
SOFTWARE, PC
synchrophasors ........................................................... 5-352
see entry for EnerVista UR Setup
THEORY OF OPERATION .................................................. 8-1
SOURCE FREQUENCY .................................................... 6-19
THERMAL MODEL
SOURCE TRANSFER SCHEMES ................................... 5-226
SOURCES
THERMAL OVERLOAD PROTECTION
description ...................................................................... 5-5
example use of .............................................................. 5-93
settings ....................................................................... 5-299
metering ........................................................................ 6-16
specifications ................................................................. 2-21
TIME .................................................................................. 7-2
settings .................................................................5-92, 5-93
TIME OVERCURRENT
SPECIFICATIONS ............................................................ 2-16
see PHASE, NEUTRAL, and GROUND TOC entries
STANDARD ABBREVIATIONS ........................................... G-5
TIMERS ......................................................................... 5-149
STATUS INDICATORS .............................................4-14, 4-16
GE Multilin D60 Line Distance Protection System ix

INDEX
TOC USER-PROGRAMMABLE LEDs

ground ......................................................................... 5-208 custom labeling ..............................................................4-22
neutral ......................................................................... 5-198 defaults..........................................................................4-16
phase .......................................................................... 5-192 description ............................................................ 4-15, 4-16
specifications................................................................. 2-17 Modbus registers ........................................................... B-28
TRACEABILITY settings ..........................................................................5-68
data ..................................................................... 4-11, 4-12 specifications .................................................................2-21
overview ........................................................................ 4-10 USER-PROGRAMMABLE PUSHBUTTONS
rules .............................................................................. 4-12 FlexLogic operands ...................................................... 5-143
TRACKING FREQUENCY ........................................ 6-20, B-50 Modbus registers .................................................. B-32, B-49
TRANSDUCER I/O settings ..........................................................................5-71
actual values ................................................................. 6-23 specifications .................................................................2-22
settings .............................................................5-343, 5-344 USER-PROGRAMMABLE SELF TESTS
specifications................................................................. 2-24 Modbus registers ........................................................... B-30
wiring ............................................................................ 3-20 settings ..........................................................................5-69
TRIP BUS USERST-1 BIT PAIR ....................................................... 5-335
settings ....................................................................... 5-240
TRIP LEDs ....................................................................... 5-68 V
TRIP OUTPUT
VAR-HOURS ........................................................... 2-23, 6-19
VIBRATION TESTING .......................................................2-28
logic ............................................................................ 5-254
VIRTUAL INPUTS
actual values ................................................................... 6-4
settings ....................................................................... 5-250
commands ...................................................................... 7-1
specifications................................................................. 2-20
TROUBLE INDICATOR .............................................. 1-19, 7-6
logic ............................................................................ 5-328
Modbus registers .................................................... B-9, B-65
settings ........................................................................ 5-328
U VIRTUAL OUTPUTS
actual values ................................................................... 6-6
UL APPROVAL ................................................................. 2-29 FlexLogic operands ...................................................... 5-142
UNAUTHORIZED ACCESS Modbus registers ........................................................... B-66
commands ..................................................................... 5-25 settings ........................................................................ 5-331
resetting .......................................................................... 7-2 VOLTAGE BANKS ............................................................5-91
UNBLOCKING SCHEME VOLTAGE DEVIATIONS ...................................................2-28
FlexLogic operands ...................................................... 5-135 VOLTAGE ELEMENTS .................................................... 5-226
Modbus registers ...........................................................B-42 VOLTAGE METERING
settings ....................................................................... 5-321 Modbus registers ........................................................... B-13
UNDERFREQUENCY specifications .................................................................2-23
FlexLogic operands ...................................................... 5-141 values ............................................................................6-17
logic ............................................................................ 5-256 VOLTAGE RESTRAINT CHARACTERISTIC ..................... 5-192
settings ....................................................................... 5-256 VT FUSE FAILURE
specifications................................................................. 2-19 logic ............................................................................ 5-293
UNDERVOLTAGE Modbus registers ........................................................... B-56
auxiliary ........................................................................ 2-19 settings ........................................................................ 5-292
phase ................................................................. 2-19, 5-228 VT INPUTS ....................................................... 3-11, 5-6, 5-91
UNDERVOLTAGE CHARACTERISTICS .......................... 5-226 VT WIRING ......................................................................3-11
UNEXPECTED RESTART ERROR .................................... 7-10 VTFF
UNIT NOT PROGRAMMED ........................................ 5-88, 7-7 FlexLogic operands ...................................................... 5-140
UNPACKING THE RELAY ................................................... 1-2 see VT FUSE FAILURE
UNRETURNED MESSAGES ALARM ................................. 5-86
UPDATING ORDER CODE ................................................. 7-3
URPC
see entry for ENERVISTA UR SETUP W
USER-DEFINABLE DISPLAYS
WARNINGS ....................................................................... 1-1
example ........................................................................ 5-79
WARRANTY ......................................................................G-7
invoking and scrolling .................................................... 5-77
WATT-HOURS ......................................................... 2-23, 6-19
WATTMETRIC ZERO-SEQUENCE DIRECTIONAL
settings ................................................................ 5-77, 5-79
actual values ..................................................................6-22
specifications................................................................. 2-22
settings ........................................................................ 5-205
specifications .................................................................2-19
WEB SERVER PROTOCOL ...............................................5-53
WEBSITE .......................................................................... 1-2
x D60 Line Distance Protection System GE Multilin

INDEX
Z
ZERO SEQUENCE CORE BALANCE ................................ 3-11
GE Multilin D60 Line Distance Protection System xi

INDEX
xii D60 Line Distance Protection System GE Multilin

d60

Uploaded by

Document Informationclick to expand document information

Copyright:

Available Formats

d60

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

d60

Uploaded by

Copyright:

Available Formats

GE

D60 Line Distance Protection

Manual P/N: 1601-0089-Z2 (GEK-119515A)

1. GETTING STARTED 1.1 IMPORTANT PROCEDURES

2. PRODUCT DESCRIPTION 2.1 INTRODUCTION

3. HARDWARE 3.1 DESCRIPTION

GE Multilin D60 Line Distance Protection System iii

3.2.6 CONTACT INPUTS AND OUTPUTS................................................................3-12

4. HUMAN INTERFACES 4.1 ENERVISTA UR SETUP SOFTWARE INTERFACE

5. SETTINGS 5.1 OVERVIEW

iv D60 Line Distance Protection System GE Multilin

5.3 REMOTE RESOURCES

GE Multilin D60 Line Distance Protection System v

5.9 TRANSDUCER INPUTS AND OUTPUTS

6. ACTUAL VALUES 6.1 OVERVIEW

7. COMMANDS AND 7.1 COMMANDS

vi D60 Line Distance Protection System GE Multilin

7.1.2 VIRTUAL INPUTS.............................................................................................. 7-1

8. THEORY OF OPERATION 8.1 DISTANCE ELEMENTS

9. APPLICATION OF 9.1 APPLICATION GUIDELINES

GE Multilin D60 Line Distance Protection System vii

9.5.2 EXAMPLE .........................................................................................................9-14

10. MAINTENANCE 10.1 MODULES

A. FLEXANALOG AND A.1 PARAMETER LISTS

B. MODBUS B.1 MODBUS RTU PROTOCOL

C. IEC 61850 C.1 OVERVIEW

viii D60 Line Distance Protection System GE Multilin

C.4 GENERIC SUBSTATION EVENT SERVICES: GSSE AND GOOSE

D. IEC 60870-5-104 COMMS. D.1 IEC 60870-5-104 PROTOCOL

E. DNP COMMUNICATIONS E.1 DEVICE PROFILE DOCUMENT

F. RADIUS SERVER F.1 RADIUS SERVER CONFIGURATION

G. MISCELLANEOUS G.1 CHANGE NOTES

GE Multilin D60 Line Distance Protection System ix

x D60 Line Distance Protection System GE Multilin

1 GETTING STARTED 1.1IMPORTANT PROCEDURES

a) GENERAL CAUTIONS AND WARNINGS

GE Multilin D60 Line Distance Protection System 1-1

1.1.2 INSPECTION PROCEDURE

Figure 1–1: REAR NAMEPLATE (EXAMPLE)

1-2 D60 Line Distance Protection System GE Multilin

1.2UR OVERVIEW 1.2.1 INTRODUCTION TO THE UR

1.2.2 HARDWARE ARCHITECTURE

Figure 1–2: UR BLOCK DIAGRAM

GE Multilin D60 Line Distance Protection System 1-3

Figure 1–3: UR-SERIES SCAN OPERATION

1-4 D60 Line Distance Protection System GE Multilin

1.2.3 SOFTWARE ARCHITECTURE

1.2.4 IMPORTANT CONCEPTS

GE Multilin D60 Line Distance Protection System 1-5

1.3ENERVISTA UR SETUP SOFTWARE 1.3.1 PC REQUIREMENTS

Figure 1–4: ADDING UR DEVICE IN LAUNCHPAD WINDOW

1-6 D60 Line Distance Protection System GE Multilin

Figure 1–5: IDENTIFYING THE UR DEVICE TYPE

Figure 1–6: UR DEVICE ADDED TO LAUNCHPAD WINDOW

1.3.3 CONFIGURING THE D60 FOR SOFTWARE ACCESS

GE Multilin D60 Line Distance Protection System 1-7

b) CONFIGURING SERIAL COMMUNICATIONS

Figure 1–7: CONFIGURING SERIAL COMMUNICATIONS

1-8 D60 Line Distance Protection System GE Multilin

'DWDIURPWRUHPRWHHQG 3LORW 7UDQVGXFHU