Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd
Upload
0 views

Course-4ICE

ice motor

Uploaded by

darrelltrash
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
0 views

Course-4ICE

ice motor

Uploaded by

darrelltrash
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 33

See discussions, stats, and author profiles for this publication at: https://www.researchgate.

net/publication/340174068

Course-4 ICE

Presentation · March 2020


DOI: 10.13140/RG.2.2.16208.66566

CITATIONS READS

0 1,162

1 author:

Nazaruddin Sinaga
Diponegoro University
269 PUBLICATIONS 1,132 CITATIONS

SEE PROFILE

All content following this page was uploaded by Nazaruddin Sinaga on 26 March 2020.

The user has requested enhancement of the downloaded file.


Nazaruddin Sinaga
Laboratorium Efisiensi dan Konservasi Energi
Universitas Diponegoro
IMPORTANT ENGINE
CHARACTERISTICS
• In this chapter, some basic geometrical relationships and the
parameters commonly used to characterize engine operation
are developed.
• The factors important to an engine user are:
1. The engine's performance over its operating range
2. The engine's fuel consumption within this operating range
and the cost of the required fuel
3. The engine's noise and air pollutant emissions within this
operating range
4. The initial cost of the engine and its installation.
5. The reliability and durability of the engine, its
maintenance requirements, and how these affect
engine availability and operating costs
▪ These factors control total engine operating costs-
usually the primary consideration of the user-and
whether the engine in operation can satisfy
environmental regulations.
▪ This course is concerned primarily with the
performance, efficiency, and emissions
characteristics of engines; the omission of the other
factors listed above does not, in any way, reduce
their great importance.
Engine performance is more precisely defined by:
1. The maximum power (or the maximum torque) available at
each speed within the useful engine operating range
2. The range of speed and power over which engine
operation is satisfactory
The following performance definitions are commonly used:
❑ Maximum rated power. The highest power an engine is
allowed to develop for short periods of operation.
❑ Normal rated power. The highest power an engine is allowed
to develop in continuous operation.
❑ Rated speed. The crankshaft rotational speed at which rated
power is developed.
GEOMETRICAL PROPERTIES OF
RECIPROCATING ENGINES
The following parameters define the basic geometry, of
a reciprocating engine (see Fig. 2.1):
Compression ratio rc :

where Vd, is the displaced or swept volume and Vc is


the clearance volume.
FIGURE 2-1
Geometry of cylinder, piston,
connecting rod, and crankshaft
where B = bore, L = stroke,
I = connecting road length,
a = crank radius,
 = crank angle.
• Ratio of cylinder bore to piston stroke:

• Ratio of connecting rod length to crank radius:

• The stroke and crank radius are related by


• Typical values of these parameters are: rc = 8 -
12 for SI engines and 12 - 24 for CI engines;
• B/L = 0.8 to 1.2 for small- and medium-size
engines, decreasing to about 0.5 for large
slow-speed CI engines;
• R = 3 - 4 for small-and medium-size engines,
increasing to 5 - 9 for large slow-speed CI
engines.
The cylinder volume V at any crank position  is

where s is the distance between the crank axis and the piston pin
axis (Fig. 2-I), and is given by
The angle , defined as shown in Fig. 2-1, is
called the crank angle.
Equation (2.4) with the above definitions can be
rearranged:

The combustion chamber surface area A at any


crank position  is given by
where Ach is the cylinder head surface area and Ap is the piston
crown surface area. For flat-topped pistons, Ap = B2/4.
Using Eq. (2.5), Eq. (2-7) can be rearranged

An important characteristic speed is the mean piston speed Sp :

where N is the rotational speed of the crankshaft.


• Mean piston speed is often a more
appropriate parameter than crank rotational
speed for correlating engine behavior as a
function of speed.
• For example, gas-flow velocities in the intake
and the cylinder all scale with Sp. The
instantaneous piston velocity Sp, is obtained
from
• The piston velocity is zero at the beginning
of the stroke, reaches a maximum near the
middle of the stroke, and decreases to zero
at the end of the stroke.
• Differentiation of Eq. (2.5) and substitution
gives

• Figure 2-2 shows how S, varies over each


stroke for R = 3.5
FIGURE 2-2 Instantaneous piston speed/mean piston
speed as a function of crank angle for R = 3.5.
• Resistance to gas flow into the engine or
stresses due to the inertia of the moving
parts limit the maximum mean piston speed
to within the range 8 to 15 m/s (1500 to 3000
ft/min).

• Automobile engines operate at the higher end


of this range; the lower end is typical of large
marine diesel engines.
2.3 BRAKE POWER AND TORQUE
• Engine torque is normally measured with a dynamometer.
• The engine is clamped on a test bed and the shaft is
connected to the dynamometer rotor.
• Figure 2-3 illustrates the operating principle of a
dynamometer.
The rotor is coupled electromagnetically, hydraulically, or by
mechanical friction to a stator, which is supported in low
friction bearings.
The stator is balanced with the rotor stationary.
The torque exerted on the stator with the rotor turning is
measured by balancing the stator with weights, springs, or
pneumatic means.
FIGURE 2-3 Schematic of principle of operation of dynamometer
❑ Note that torque is a measure of an engine's
ability to do work; power is the rate at which
work is done.

❑ The value of engine power measured as


described above is called brake power Pb.

❑ This power is the usable power delivered by


the engine to the load-in this case, a "brake."
TUGAS 1 MOTOR BAKAR TORAK
Terjemahkan dan buat Power Point buku INTERNAL
COMBUSTION ENGINES, Colin R. Ferguson and Allan T. Kirkpatrick
(untuk Kelompok 1 s/d 13)
1. Terjemahan dan Power Point harus dapat dimengerti kalimat-
kalimatnya dengan jelas.
2. Rumus-rumus atau persamaan ditulis kembali dengan
Equation yang terdapat pada Microsof Office (jangan dicopy
sebagai picture).
3. Gambar2 dan Tabel harus bagus dan jelas
4. Dibuat dalam softcopy (MS-Word dan Power Point)dan
hardcopy
5. Dikerjakan berkelompok
6. Dikumpulkan tanggal 18 September 2018 di Laboratorium
Efisiensi dan Konservasi Energi
THANK YOU

View publication stats

You might also like