Service Training

The new Audi A4 05

Self-Study Programme 343

The new Audi A4 05

Audi introduces a new model generation that is obvious at first glance. The front-end styling of both saloon and Avant models is new, with the addition of the characteristic Audi single-frame grille. The rear end, with its distinct horizontal lines, and the sides, where the shoulder line lends the body a distinctly sporty look, are also new. Driving pleasure, superior technology, exciting styling and a level of luxury that even satisfies the demands made of the luxury car class. The architecture of the drivers area, especially the cockpit a perfect synthesis of ergonomics, function and design is pioneering.

343_009

Excellence in design & performance

Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

The body. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Occupant protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

The engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

The chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

The heating / air conditioning system . . . . . . . . . . . . . . 24

The convenience electronics . . . . . . . . . . . . . . . . . . . . . . 26

The purpose of the Self-Study Programme is to provide a basic knowledge of the design and function of new models, new automotive components or new technologies. The Self-Study Programme is not a Repair Manual! All values given are intended as a guideline only, and refer to the software version valid at the time of publication of the SSP. For maintenance and repair work, always refer to the current technical literature.

Reference

Note

Introduction

Overview
Dimensions of the Audi A4 05 Avant.

343_010

Dimensions of the Audi A4 05 saloon.

343_011

The body

Overview of the body

One of the key factors contributing to the vehicle's lower kerb weight was the use of high-strength body panels, which account in total for 45% of the bodyshell weight. These special panels are used especially at the body front end, where they are intended to absorb as effectively as possible the impact energy in the event of a head-on collision. In the floorpan area, the occupant cell is protected by three large tailored blanks in varying wall thickness. In the occupant cell area, tailored blanks are connected sturdily and homogeneously to the front and rear ends of the vehicle by a branched support system. At the rear end of the vehicle, the side members are made from tailored blanks with different materials and wall thickness.

Note The repair concept is identical to that of the Audi A4 04 (B6).

Front end adapted to singleframe radiator grille

Optimised body New exterior design Installation space for diesel particulate filter Compliance with applicable vehicle safety requirements

B-pillar optimised for crash safety

Installation space in centre tunnel has been enlarged to accommodate diesel particulate filter and multitronic transmission

343_008

Occupant protection

Safety system
The development objective for the safety system in the Audi A4 05 was clearly defined: The system must comply with all legislation now in effect and pass all current consumer tests, not to mention meeting Audi's stringent in-house requirements. The safety system in the Audi A4 05 is based on the systems in the Audi A3 Sportback and Audi A6 05. The complete system, as well as the adopted components, were adapted to suit the Audi A4 05.

Reference For further information about the safety system, refer to Self-Study Programmes SSP 323 Audi A6 05 and SSP 332 Audi A3 Sportback.

G128 Seat occupied sensor, front passenger side G180 Side airbag crash sensor, front passenger side (front door)

N131 Airbag igniter 1, front passenger side N132 Airbag igniter 2, front passenger side

G284 Front airbag crash sensor, front passenger side (right front end) E224 Airbag disabling key switch, front passenger side K145 Airbag disabled warning lamp, front passenger side (PASSENGER AIRBAG OFF) K19 Seat belt warning system warning lamp K75 Airbag warning lamp J285 Control unit with display in dash panel insert G283 Front airbag crash sensor, driver side (left front end)

N95 Airbag igniter, driver side N250 Airbag igniter -2-, driver side

J623 Engine control unit

T16 16-pin connector, diagnosis connection G179 Side airbag crash sensor, driver side (front door)

J393 Convenience system central control unit

The safety system in the Audi A4 05 consists of the following components and functions: Airbag control unit Driver and front passenger airbags, two-stage Front side airbags Sideguards (head airbags) Side impact detection sensors on the C-pillar Side impact detection sensors in the front doors (pressure sensors) Crash sensors for intelligent head-on collision detection, so-called upfront sensors Front belt tensioners Seat belt reminders for driver and front passenger Switches in the front seat-belt buckles Seat occupied sensor, front passenger seat Active head restraints in the front seats Rear collision detection

Rear side airbags and deactivation of the front passenger front airbag by keyswitch with associated warning lamp are available as optional extras. In some countries, such as the North American market, deviating specifications may apply due to different country-specific requirements.

N154 Belt tensioner igniter -2-, front passenger side N200 Side airbag igniter, front passenger side G257 Rear side airbag crash sensor, front passenger side (C-pillar)

N252 Curtain airbag igniter, front passenger side

E25 Belt switch - front passenger side J234 Airbag control unit E24 Belt switch - driver side

N251 Curtain airbag igniter, driver side 343_007 G256 Rear side airbag crash sensor, driver side (C-pillar) N199 Side airbag igniter, driver side N153 Belt tensioner igniter -1-, driver side

Diagnosis

K-wire switch VAS 6017 B

Like in the Audi A4 01, K-wire switch is also required in the Audi A4 05 for communication between the individual vehicle systems and the VAS testers. Since the new control units are diagnosable via CAN only, the new K-wire switch VAS 6017 B must be used. K-wire switch VAS 6017 B replaces switch VAS 6017 A.

Communication
If communication is to be established between a control unit and a VAS tester, the tester sends the appropriate address word via the diagnosis CAN data bus. The K-wire switch VAS 6017 B does not evaluate signals on the diagnosis CAN data bus, rather it relays them directly to the vehicle. If the tester receives no response from the control unit on the diagnosis CAN data bus, its resends the appropriate address word, this time via the K-wire. The K-wire switch receives this information and relays it to the vehicle both on the K-wire and on the L-wire. If the control unit sends its response on the L-wire, the K-wire switch detects this and establishes a direct connection between the L-wire of the vehicle and the K-wire of the tester. As long as the tester is connected to a control unit via the L-wire, the contact to the K-wire of the vehicle is broken by the K-wire switch.

343_018

PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Designation Terminal 15 Unassigned or assigned on US spec vehicles Unassigned Terminal 31 Terminal 31 Data bus, diagnosis CAN bus, CAN High K-wire Unassigned Unassigned Unassigned or assigned on US spec vehicles Unassigned Unassigned Unassigned Data bus, diagnosis CAN bus, CAN High L lead Terminal 30 343_003

10

L lead K-wire

Gateway

343_004

* These control units assume the diagnosis gateway functions. They receive diagnosis data sent by the VAS testers on the diagnosis line and relay the data to the appropriate data bus. The addressed control unit evaluates this information and responds on the data bus. The control unit with diagnosis gateway function receives this data and sends it via the diagnosis line to the tester.

11

Engine

Engines in the new Audi A4 05

343_014

Diesel engines Engine R4 1.9l 2V TDI-PD R4 2.0l 2V TDI-PD (DPF) R4 2.0l 4V TDI-PD R4 2.0l 4V TDI-PD V6 2.5l TDI-VEP V6 3.0l 4V TDI-CR V6 3.0l 4V TDI-CR (DPF) kW 85 103 103 100 120 150 150

Power output bhp 115 140 140 136 163 204 204 Nm 285 310 310 310 350 450 450

Torque

Engine code

Emission category

BKE BPW BLB BNA BDG BKN BKN

EU IV EU IV with DPF EU IV EU IV EU IV EU IV EU IV with DPF

12

343_015

Petrol engines Engine R4 1.6l 2V R4 1.8l 5V Turbo R4 2.0l 4V FSI R4 2.0l 5V MPI R4 2.0l 4V TFSI V6 3.0-litre 5V MPI V6 3.2-litre 4V FSI V8 4.2-litre 5V MPI kW 75 120 110 96 147 160 188 53

Power output bhp 102 163 150 130 200 218 255 344 Nm 148 225 200 195 280 300 330 410

Torque

Engine code

Emission category

ALZ BFB AWA ALT BGB BBJ AUK BHF

EU IV EU IV EU IV EU IV EU IV EU IV EU IV EU IV

13

Engine

2.0-litre pump injection engine

New features
A balancer shaft module with two counter-rotating shafts provides an effective reduction in second-order engine oscillations. The module is a built-up module consisting of two housing halves. The balancer shafts rotate in bearing bushes and are driven by the crankshaft at double the crankshaft speed via a sleeve-type chain. The second shaft is driven in the opposite direction to the crankshaft via a pair of gears. This balancer shaft connects to a hexagon bolt at the front end and also drives the oil pump.

Housing upper section Sprocket crankshaft

Balancer shaft 1

Balancer shaft 2 Sprocket balancer shaft

Bearing bushings

Chain tensioner Oil pump drive

Oil pump

Housing lower section

343_016

14

Exhaust-gas recirculation cooler

A lower combustion temperature is required to reduce nitrogen oxide (NOx) emissions. This was achieved by using a variable, water-cooled exhaust gas recirculation cooler. The exhaust gas recirculation cooler has a bypass valve, which is opened when the engine is cold. This allows the recycled exhaust gases to bypass the cooler and reach the intake end of the engine uncooled. As a result, the catalytic converter reaches its operating temperature more quickly. The valve is closed when the engine temperature exceeds 35C, and the exhaust gases flow via the cooler. The bypass valve is controlled by a solenoid valve via a vacuum box, whereby the valve is closed when the solenoid is de-energised and the exhaust gases flow via the cooler.

Exhaust ducting when the engine is cold

Exhaust ducting when the engine is hot

Exhaust gas flow Coolant

Exhaust gas flow Coolant

Vacuum box

Exhaust manifold connection

Coolant inlet

Coolant outlet

343_017

15

Engine

Particulate filter in the 3.0-litre V6 common rail engine and in the 2.0-litre pump injection engine
(roll-out planned for 1st quarter 2005) Audi uses regenerative, additive-free particulate filters. The Catalysed Soot Filter (CSF for short) has filter coatings containing precious metals which act in two ways. During the passive regeneration process, which takes place when the car is being driven at motorway speeds, temperatures of between 350 and 500 C are reached. This causes the soot particulates deposited in the particulate filter to be converted into CO2. The process of active regeneration runs in the background and is triggered automatically by temperatureincreasing measures.

Treated soot-free exhaust gas

Temperature sender

Connections to the differential pressure sensor

343_021

Pretreated exhaust gas containing soot

Particulate separation

343_020

Reference For information on design and function, refer to Self-Study Programme 325.

16

Transmission
Installed transmission

332_025 332_024

The new A4 engine/ transmission variants

Engine Manual gearbox Petrol engines R4 1.6l 2V R4 2.0l 5V MPI R4 1.8l 5V T MPI R4 2.0l 4V FSI R4 2.0l 4V T FSI V6 3.0l 5V MPI V6 3.2l 4V FSI V8 4.2l 5V MPI 75 96 120 110 147 160 188 253 kW 102 130 163 150 200 218 255 344 bhp front ML285-5F ML285-5F ML285-5F ML285-5F ML310-6F ML310-6F ML310-6Q ML310-6Q ML310-6Q ML450-6Q ML310-6Q

Transmission Automatic transmission front quattro

quattro

VL300-F VL300-F VL300-F VL300-F VL300-F VL300-F AL420-6Q 5HP19Q AL420-6Q AL420-6Q

Diesel engines R4 1.9l 2V TDI-PD R4 2.0l 2V TDI-PD R4 2.0l 4V TDI-PD V6 2.5l TDI V6 3.0l TDI-CR 85 103 103 120 150 115 140 140 163 204 ML285-5F ML310-6F ML310-6F ML350-6F ML450-6Q VL300-F VL300-F VL300-F AL420-6Q

17

The chassis

General
Three chassis variants are available for the Audi A4 `05. In the case of the sports suspension, ride height has been lowered by 20mm compared to the standard suspension system. For the heavy-duty suspension, ride height was raised by 13 mm. Both suspensions use different tuning parts (springs, shock absorbers, anti-roll bars). In the case of the heavy-duty suspension system, additional covers are fitted to the track rod and the trapezoidal link on the rear axle to provide effective stone chip protection.

Front suspension
The proven four-link front suspension is also used in the new Audi A4 `05 (see SSP 161). The following new developments will be introduced: Subframe The geometry of the subframe was modified by lowering the engine position on the 4-cylinder TDI engines. Anti-roll bars Geometric modifications were necessary due to the different engine position. Guide link The guide link bearing connecting the link and subframe was redesigned. Drive shafts Vehicles with the AL420 gearbox have a newly developed triple roller joint drive shaft with a smaller triple roller joint. A new special tool T40084 was developed for installing/removing the new triple roller joint.

Bearing pedestal

Spring / damper unit

Damper bearing

Upper transverse rod Guide link

Track rod

Swivel bearing

Anti-roll bar Subframe

Common part from previous model Common part from S4 model year 2004 New part
18 Support link Wheel bearing / wheel hub 343_012

Rear suspension
The rear suspension is an advancement on the trapezoidal-link suspension familiar from the Audi A4 `04. In particular the bearing set-ups have been modified. Several bearing elements from the Audi A6 `04 are used.

Wheel carrier

Subframe Upper track control arm

Damper bearing

Anti-roll bar Shock absorber

Outer rear trapezoidal link bearing

Spring

Inner front trapezoidal link bearing

Common part from previous model Common part from A6 model year 2004/2005 New part

Trapezoidal link

Wheel bearing / wheel hub 343_013

Reference For information on design and function, refer to Self-Study Programme 161.

Suspension alignment/setting
The alignment and setting procedures, as well as the setting positions on the vehicle, are unchanged from the previous model.

19

Running gear

Brake system
The A4 `05 models with 120 and 147 kW four-cylinder engines have 16-inch brake systems. The Teves FNRG 60 16-inch frame-design caliper brake is already being used in the A6 and A8. This system was optimised for the A4 and specially adapted for the new vehicle. The CII-41 floating caliper brake on the rear axle originates from the S4 `04. The brake was adapted for use in the A4 `05 by reducing the piston diameter to 41mm, and a solid brake disc is used. The brake control mechanism is unchanged from the previous model.

Units

Front suspension Brake disc ( x thickness) Brake caliper

Rear suspension Brake disc ( x thickness) 245x10 solid 245x10 solid 245x12 solid 288x12 solid 300x22 vented TRW C38 TRW C38 TRW C38 TRW CII-41 16" TRW CII-43 17" Brake caliper

1.6-litre 75 KW

280x22 vented 280x25 vented 312x25 vented 320x30 vented 345x30 vented

TRW C54 ContiTeves FN3-57 15" ContiTeves FN3-57 15" ContiTeves FNRG-60 16" ContiTeves FNRG-60 17"

Four-cylinder 85 - 103 kW 1.8-litre 120 kW

All six-cylinder 2.0-litre TFSI 4.2-litre V8

ESP
As previously in the A6 `04, the new-generation system Bosch 8.0 ESP system is also featured on the A4 `05 (see SSP 324). The fundamental difference in design between the A4 and A6 systems is the use of passive wheel speed sensors.

343_027

In addition to the familiar subfunctions, the A4`06 has a new function called Hydraulic Fading Compensation (HFC). By comparing the brake pressures at which ABS system begins to operate, the system can detect brake fading at an early stage. The greater the fading, the higher the brake pressure needed to activate the ABS system. If fading is detected, ESP raises the overall pressure in the system by building up additional brake pressure. The driver does not need to apply more pressure to the brake pedal, in order to achieve the same braking effect as with fading-free brakes. The "hill-holder" function implemented for the A6 `05 models with multitronic transmission is not available for the A4 `05 from launch.

20

Steering system
A modified hydraulic rack and pinion steering system is used in the A4 `05. In particular, the turn-in precision and the feedback on roll steer effect were optimised compared to the previous model. The steering valve characteristic was adapted to the new axle kinematics. Turn-in was improved through the use of stiffer track rods. For the first time in this class, the "Servotronic" function is standard for all 6-cylinder vehicles and the 2.0-litre TFSI. "Servotronic" is optional for the other 4-cylinder models with power outputs of 96 kW and higher. The Servotronic II system familiar from the A6 and A8 is used (for information on mode of operation, see SSP 285). Different characteristic curves for steering wheel torque and pressure as a function of vehicle speed are implemented in the steering system. The systems on the S4 `05 and A4 `05 have different characteristic curves. The Servotronic solenoid valve is now connected directly to the solenoid valve. The second connector in the wheel housing was retained for installation reasons.

The steering column was adopted from the previous model, and the steering wheels from the A3 04 are used.

343_029

21

Running gear

Wheels and tyres

343_023

Basic wheels For 1.6-litre and 1.9-litre TDI versions: Steel wheel with full sized wheel trim 7Jx16 (1) with 205/55R16 tyres 2.0-litre engines and larger: *Cast aluminium wheel 7Jx16 (2) with 205/55R tyres; 2.0T and 6-cylinder with 215/ 55R16 tyres

Winter wheels Steel wheel 7Jx16 (1) with 205/55R16 tyres

Optional wheels Cast aluminium wheel 7Jx16 (4) with 205/55R tyres; 2.0T and 6-cylinder with 215/ 55R16 tyres *Cast aluminium wheel 7Jx16 (5) with 205/55R tyres; 2.0T and 6-cylinder with 215/ 55R16 tyres Cast aluminium wheel 7.5Jx16 (3) with 235/45R17 tyres;

Cast aluminium wheel 7Jx16 (2) with 205/55R16 tyres

Cast aluminium wheel 7.5Jx17 (7) with 235/45R17 tyres

Cast aluminium wheel 7.5Jx17 (3) with 235/45R17 tyres;

Lightweight forged aluminium wheel 7.5Jx16 (6) with 215/55R16 tyres

Cast aluminium wheel 7.5Jx17 (8) with 235/45R17 tyres *Cast aluminium wheel 7.5Jx17 (9) with 235/45R17 tyres

* new wheels

22

The A4 `05 is equipped as standard with "Tire Mobility System". As an option, the customer can choose between a spare wheel fitted with a readyfor-road tyre or a temporary spare wheel. The PAX run-flat system with one all-season wheel is a new option for the A4 05 (design and function see SSP 285).

343_036

Tyre pressure monitoring system

The tyre pressure monitoring system was adopted from the previous model. The system is now operated using the 'Reset' key and the rocker switch on the windscreen wiper stalk (see operating instructions).

23

The heating / air conditioning system

New features of the air conditioning system in the Audi A4

General
The air conditioning concept familiar from the Audi A4 01 was largely adopted into the Audi A4 05. However, the software has been expanded to allow the air-conditioning parameters to be adapted to suit the individual preferences of the vehicle occupants. As a result, several functions can now be adjusted more finely. All adjustments can be made in the service workshop using the VAG diagnostic tester VAS 5051/5052. Air outlet temperatures, for example, can be increased or decreased slightly to perceived temperatures comfortable to the vehicle occupants. Partial air flows can also be directed to various outlets.

Reference For general information about the design and function of the air conditioning system in the Audi A4 05, please refer to Self-Study Programme 254, Audi A4 01 - Technology.

343_030

Adaption
The so-called physiological adaption of the air conditioning system in the new Audi A4 05 is performed using the additional adaption channels. Incidentally, ' physiology' is a medical term describing how stimuli are perceived by the cardiovascular system and how humans feel. Adaption "1" on channel 10 directs a minimum air flow to the windscreen inner surface via the defroster vent. This prevents fogging of the windscreen. Such adjustments can also be made for the footwell outlets. The adaption function also allows nominal out-flow temperature and fresh air blower speed to be adjusted more finely, and provides extended air recirculation independent of the signal from the air quality sensor G263.

24

Overview of the adaption channels

Adaption channel 01 02 03

Description

Offset added to the desired temperature at the start of overheating. Offset which remains added to the nominal temperature after the end of the overheating phase. Bidirectional engine control unit interface: Adaption "1" means that compressor shut-off/reduction signals from the engine control unit are ignored. Engine compressor speed ratio "0" Decision on auxiliary heating/auxiliary ventilation is made by the air conditioning system "1" Previously selected operating mode is activated independently of the air conditioning system "0" After terminal 15 OFF, the auxiliary heating / auxiliary ventilation function runs until the timer expires "1" Auxiliary heating/auxiliary ventilation mode is also deactivated at terminal 15 OFF Adjustment of fresh air blower output reduction during a telephone conversation Adjustment of undervoltage shut-off for the auxiliary ventilation function Minimum air flow rate to defroster vent "0" Yes "1" No Nominal out-flow temperature "0" Mixed air characteristic, depending on country code "1" Adaption for "Rest of World", warmer "2" Adaption for "Rest of World" "3" USA / Japan "4" Cooler than USA / Japan Fresh air blower "0" Fresh air blower characteristic is set automatically via the country code "1" Less air in relation to fresh air blower characteristic via country code "2" Fresh air blower characteristic is set automatically via country code "3" More air in relation to fresh air blower characteristic via country code Transient response during heater operation "0 " Default setting "1" Cooler, Scandinavia Physiological adaption "0" Default setting "1" Warmer "2" Default setting "3" Cooler Recirculated air / fresh air handling "0" Default setting (familiar recirculated-air handling setting) "1" New recirculated air handling setting (extended air recirculation) "2" Default setting (familiar recirculated-air handling setting) Minimum air flow to footwell during air conditioner operation "0" No "1" Yes

04 06

07

08 09 10

11

12

13

14

15

16

25

The convenience electronics

Bus topology
L-wire K-wire

Gateway

* The K-wire is not available in all engine and gearbox control units. New engine and transmission units coming onto the market can only be diagnosed via CAN bus.

26

The bus topology - as with the complete electrical system - is heavily based on the Audi A4 01. As before, the gateway is integrated in dash panel insert J285. To diagnose on the driveline CAN bus the control units adopted from the Audi A3 and Audi A6, the driveline CAN bus is connected directly to the diagnosis plug. The control units on the convenience CAN bus and on the infotainment CAN bus are also diagnosed via the K and L wires (see also chapter "Diagnosis", page 10).

Legend G85 Steering angle sender G397 Rain and light detector sensor G419 ESP sensor unit J104 ABS with EDL control unit J136 Seat and steering column adjustment control unit with memory J217 Automatic gearbox control unit J234 Airbag control unit J255 Climatronic control unit J285 Control unit with display in dash panel insert J345 Trailer detection control unit J364 Additional heater control unit J386 Driver door control unit J387 Front passenger door control unit J388 Rear left door control unit J389 Rear right door control unit J393 Convenience system central control unit J401 Operating electronics control unit, navigation J431 Headlight range control, control unit J446 Parking aid control unit J453 Multi-function steering wheel control unit J502 Control unit for tyre pressure monitoring J519 onboard power supply control unit J527 Steering column electronics control unit J623 Engine control unit J667 Power output module for left headlight J668 Power output module for right headlight J706 Seat occupied recognition control unit R Radio R36 Telephone transmitter and receiver unit R41 CD changer R78 TV tuner R146 Satellite radio (SDARS)

Driveline CAN bus:500 kBaud Convenience CAN bus:100 kBaud Infotainment CAN bus:100 kBaud LIN K-wire L-wire Panasonic bus Various subbus systems
343_001

27

Convenience electronics

Control unit with display in dash panel insert J285

343_002

Basic functions
The dash panel insert in the Audi A4 '05 is based on the dash panel insert from the Audi A4 '01. The basic functions of the dash panel insert are unchanged. The innovations were necessary due to the adoption of components and units from the Audi A6 '05 and Audi A3 '04. The dash panel insert also incorporates: the dash panel insert a gateway for linking the three data buses driveline CAN bus, convenience CAN bus and infotainment CAN bus the immobiliser

Driver information system

The driver information system basically corresponds to the system used in the A3 Sportback.

A fuel tank symbol has been added for displaying the vehicle range. The symbol is for differentiation purposes, since the function "Distance" has also been added to the previous displays.

Range

Distance

343_031

343_032

28

Diesel particulate filter warning

343_033

Audi adaptive light faulty: The vehicle is equipped with the optional adaptive light and a fault is present in the headlight range control, control unit J431 (see SSP 326 page 34).
343_034

In the case of multistep automatic transmissions, the currently selected gear is displayed in addition to the D or S symbol in Tiptronic mode

343_035

Engine-specific differences
Depending on what engine is fitted in the vehicle, there are differences between detail functions in the dash panel insert. A distinction is made between engines previously available in the Audi A4 01 and engines introduced since the Audi A3 04 or the Audi A6 05.

"old engines" Engine 1.6l 75kW (102 bhp) 2.0l 96 kW (130 bhp) 2.0l FSI 110 kW (150 bhp) 1.8l T 120kW (163 bhp) 3.0l 160kW (220 bhp) 1.9l TDI 85kW (115 bhp) 2.5l TDI 120kW (163 bhp)

"new engines" 2.0l T, 147kW (200 bhp) 3.2l FSI 188 kW (255 bhp) 4.2l 253 kW (344 bhp) 2.0l TDI 103 kW (140 bhp) 3.0l TDI 150kW (204 bhp)

Extended service intervals

Generation 2: The computation software is integrated in the dash panel insert

Generation 3: The computation software is integrated in the engine control unit

In both cases, the oil level/oil temperature sender G266 is connected to the dash panel insert. Depending on service interval extension, the data is used differently in data blocks 6 and 7. For a detailed description, refer to the description of the Guided Fault Finding function.

Coolant temperature

Two coolant temperature senders are fitted: The coolant temperature is measured by the coolant temperature sender G62 and transferred to the engine control unit. From here, the value is sent via CAN to the air conditioner control unit. The coolant temperature sender G2 is connected to the dash panel insert. The value is used by the display in the dash panel insert and for computing the high-temperature warning, and is also sent from here via CAN to the air conditioner control unit.

Only one coolant temperature sender is fitted: The coolant temperature is measured by the coolant temperature sender G62 and transferred to the engine control unit. From here, the value is sent via CAN to the dash panel insert and the air conditioner control unit. All high-temperature warnings are sent likewise from the engine control unit via CAN to the dash panel insert or air conditioner control unit

29

Convenience electronics

New features of the convenience electronics

Auto Lock
The Auto Lock function locks all doors and the boot lid when the vehicle exceeds a speed of approximately 15 kph. Removing the ignition key unlocks the vehicle automatically. The vehicle can also be unlocked by the driver if the 'Open' function on the central locking switch (1) or if one of the door opening levers (2) is operated.

Safety central locking

The safety central locking system offers the possibility to unlock only the driver's door and the fuel filler flap. The vehicle otherwise remains locked. This is done by turning the key once in the 'Open' direction or by pressing the 'Open' button on the radio-operated remote control. If all doors, the boot lid and the fuel filler flap are to be unlocked, this is done by turning the key twice within 5 seconds in the 'Open' direction or by pressing the 'Open' button on the radio-operated remote control twice within 5 seconds.

343_005

326_138

The "Auto Lock" and "safety central locking" functions can be activated and deactivated in the convenience system central control unit J393 using the diagnostic tester VAS 5051 (under menu item "Code control unit").

Guided Fault Finding Function/component selection Select function or component I Body (Rep. Gr. 01; 50 - 97)

V07.59.00 28/07/2004 Audi Audi A4 2001> 2005 (5) Saloon AUK 3.21 Motronic / 184 kW

General Body Repairs (Rep. Gr. 01; 50 - 77) 01 - Systems with self-diagnostic capability 46 - Convenience system central module (Rep. Gr. 57) Functions - convenience system central module (Rep. Gr. 57) I Transport mode + J393 - Interrogate control unit version + J393 - Final control diagnosis + J393 - Code control unit + J393 - Replace control unit + J393 - Read data block, general + J393 - Adapt remote control key using Adaption function (channel) * J393 - Adaption - Erase remote control key memory space + J393 - Adaption - Control unit variant (channel 61)

343_006

30

Self-study programmes on the Audi A4 05

SSP 161 The Audi A8 The suspension Order number: 440.2809.79.20

343_041

SSP 254 Audi A4 01 - Technology The dash panel insert The chassis Heating and air conditioning Order number: 040.2810.73.20

SSP 290 Audi A3 04

343_042 332_085

Introduction The body The engine The transmission The chassis The electrical system Heating/air conditioning Service

Order number: A03.5S00.01.20 SSP 323 Audi A6 05 Occupant protection

SSP 293 Audi A8 03 - Infotainment Infotainment The sound system The radio module Navigation

Order number: A04.5S00.06.20

Order number: 000.2811.13.20

343_037

343_043

SSP 325 Audi A6 05 Units The engine The transmission Order number: A04.5S00.08.20

343_038

SSP 326 Audi A6 05 Electrical system Convenience electrics Infotainment Order number: A04.5S00.09.20

SSP 332 Audi A3 Sportback The body Occupant protection The engine The chassis Convenience electronics Infotainment

Order number: A04.5S00.11.20

343_039 343_040

Vorsprung durch Technik www.audi.de

All rights reserved. Technical specifications subject to change without notice. Copyright AUDI AG I/VK-35 Service.training@audi.de Fax +49-841/89-36367 AUDI AG D-85045 Ingolstadt Technical status: 05/04 Printed in Germany A04.5S00.12.20

343