X400 02 P DTC Obd Ii R4
X400 02 P DTC Obd Ii R4
X400 02 P DTC Obd Ii R4
Refer to page 2 for important information regarding the use of Powertrain DTC Summaries.
KEY TO COLUMN HEADINGS DTC SYS Diagnostic Trouble Code. The powertrain system with which the DTC is associated EMS, TRANS, ABS/TC (DSC). DTC retrieval tools: OBD II indicates that the DTC is an OBD II code and can be accessed via a generic scan tool or WDS. JAG indicates that the DTC is not an OBD II code and is accessed only via WDS. Fault description. DIAGNOSTIC MONITOR DRIVE CYCLE for the particular DTC. Operate the vehicle as described to check for a reoccurrence of the DTC. Refer to pages 4 7. Use WDS Datalogger or Scan Tool to monitor specified engine parameter(s). 1 2 N 1 TRIP indicates that the CHECK ENGINE MIL is activated by a fault occurring during ONE TRIP. 2 TRIPS indicates that the CHECK ENGINE MIL is activated by a fault occurring during TWO CONSECUTIVE TRIPS. NO indicates that the CHECK ENGINE MIL is not activated.
Driver Warnings: N None R RED MIL / Message or Powertrain Warning Indicator A AMBER MIL / Message or Powertrain Warning Indicator C Charge indicator Control Module default action: Logged DTC stored in ECM memory buffer; Flagged DTC stored in ECM memory / CHECK ENGINE MIL activated. ECM (SYS EMS) / TCM (SYS TRANS) Connector pin number(s) Possible causes are listed in the order of diagnostic checking. HIGH VOLTAGE High voltage can be either sensor supply voltage (5 volts) or B+ voltage.
REFERENCE: It is recommended that the applicable Electrical Guide be referenced when using the information contained in this document.
Jaguar X-TYPE P DTC OBD II 2002 Model Year 2
2 4 6
1 3 5
OBD SYSTEM READINESS ENGINE MANAGEMENT If DTC P1000 is flagged after DTCs have been cleared, all engine management OBD diagnostic monitor drive cycles HAVE NOT BEEN COMPLETED. If DTC P1111 is flagged after DTCs have been cleared, all engine management OBD diagnostic monitor drive cycles HAVE BEEN COMPLETED. OBD SYSTEM READINESS TRANSMISSION Use WDS Datalogger TOTAL NUMBER OF DTC SET to determine if transmission OBD monitoring has been completed. Refer to page 7. OBD DIAGNOSTIC MONITORS The Engine Management and Transmission Control systems are continuously checked during vehicle operation by the Engine Control Module (ECM) and Transmission Control Module (TCM) on-board diagnostic (OBD) facilities. Powertrain OBD incorporates six diagnostic monitors. Each monitor has an associated group of DTCs. The diagnostic monitors will complete the diagnostic test(s) if a specified service drive cycle is carried out. The six diagnostic monitors are as follows: Heated Oxygen Sensors Monitor Adaptive Fuel Monitor Misfire Monitor Catalyst Efficiency Monitor Evaporative System Monitor Comprehensive Component Monitor (Engine Management / Transmission)
DIAGNOSTIC MONITORS DRIVE CYCLES Technicians can ensure that an OBD Monitor drive cycle is completed and that all or specific components have been checked by completing a specified drive cycle. Use the following service drive cycles to confirm that the components and subsystems covered by the Diagnostic Monitors are operating correctly. HEATED OXYGEN SENSORS MONITOR DRIVE CYCLE Upstream (Universal) oxygen sensors: 1 2 3 4 5 Engine OFF; cooling fans inoperative > 20 seconds. Start engine and bring to normal operating temperature > 82 C (180 F). Drive the vehicle between 3000 4000 rpm at a steady speed. Lift foot completely off accelerator and coast to a stop within 30 seconds. Do not touch accelerator pedal for 4 seconds after coming to a stop. Repeat step 3. Idle engine for 11 minutes.
Downstream oxygen sensors: 1 2 3 Start engine and bring to normal operating temperature > 82 C (180 F). Drive the vehicle steadily between 48 97 km/h (30 60 mph) for 10 minutes. Drive the vehicle above 3000 rpm in 4th gear at a steady speed. Lift foot completely off accelerator and coast for 30 seconds.
Oxygen sensor heaters: 1 2 Start engine and bring to normal operating temperature > 82 C (180 F). Idle engine for 3 minutes.
ADAPTIVE FUEL MONITOR DRIVE CYCLE 1 2 Start engine and bring to normal operating temperature > 82 C (180 F). Idle for a minimum of 10 minutes.
MISFIRE MONITOR DRIVE CYCLE 1 2 3 4 5 Record flagged DTC (s) and accompanying WDS DTC Monitor freeze frame(s) data. Fuel level > 25%. Start engine and bring to normal operating temperature > 82 C (180 F). Drive vehicle to the recorded freeze frame conditions (from step 1). Repeat several times.
Note regarding misfire monitor DTCs: If on the first trip, the misfire is severe enough to cause excess exhaust emission, the individual cylinder DTC plus DTC P1316 will be logged. The CHECK ENGINE MIL will not be activated. If the fault reoccurs on the second trip, the individual cylinder DTC plus DTC P1316 will be flagged, and the CHECK ENGINE MIL will be activated. If on the first trip, the misfire is severe enough to cause catalyst damage (more severe than excess exhaust emission), the CHECK ENGINE MIL will flash while the fault is present and the individual cylinder DTC plus DTC P1313 (bank 1), DTC P1314 (bank 2) will be logged. When the fault is no longer present the MIL will be deactivated. If the fault reoccurs on the second trip, the CHECK ENGINE MIL will flash while the fault is present and the individual cylinder DTC plus DTC P1313 (bank 1), DTC P1314 (bank 2) will be flagged. When the fault is no longer present the CHECK ENGINE MIL will be activated. CATALYST EFFICIENCY MONITOR DRIVE CYCLE 1 2 Start engine and bring to normal operating temperature > 82 C (180 F). Drive vehicle steadily between 1700 2500 rpm for 5 minutes.
EVAPORATIVE SYSTEM MONITOR DRIVE CYCLE 1 2 3 4 5 6 7 8 Ensure that fuel filler cap is fully closed (minimum three clicks). Fuel level > 30% and < 85%. Using WDS, perform ECM DTC Clear (even if no DTCs are flagged). Drive vehicle for a minimum of 2 minutes, and until engine is at normal operating temperature. Using WDS, ensure that the EVAP Canister Purge Valve is operating by observing PURGE VAPOR MANAGEMENT VALVE DUTY CYCLE. If the valve is not active, ECM adaptions have not been learned. Conduct a green ECM Drive Cycle as described in Technical Service Bulletin. Drive vehicle to the road where the EVAP System Drive Cycle will be conducted. Stop vehicle and switch OFF the ignition. Leave ignition OFF for 30 seconds, then restart the engine. Accelerate briskly to 80 km/h (50 mph) ensuring that the engine speed reaches a minimum of 3500 rpm for a minimum of 5 seconds. (0.040 inch EVAP Test) View WDS PURGE VAPOR MANAGEMENT VALVE DUTY CYCLE, CANISTER CLOSE VALVE VAPOR RECOVERY SYSTEM, and FUEL TANK PRESSURE VAPOR RECOVERY SYSTEM. Avoiding high engine loads, drive the vehicle steadily between 65 km/h (40 mph) and 100 km/h (60 mph). Avoid driving conditions that will produce excessive fuel movement. WDS should give an indication that the test is active (it may take up to 30 minutes before the test will initialize). When the test has initialized (EVAP Canister Close Valve CLOSED), it will take approximately 90 seconds for the test to complete. (0.020 inch EVAP Test) Continue driving vehicle as explained in Step 8 for an additional 10 minutes. Gently coast the vehicle to a stop. Allow the engine to idle for 2 minutes and view WDS PURGE VAPOR MANAGEMENT VALVE DUTY CYCLE, CANISTER CLOSE VALVE VAPOR RECOVERY SYSTEM, and FUEL TANK PRESSURE VAPOR RECOVERY SYSTEM. WDS should give an indication that the test is active. When the test has initialized (EVAP Canister Close Valve CLOSED), it will take approximately 90 seconds for the test to complete. If the 0.020 inch EVAP Test is not activated, the purge system vapor concentration may be too great. To reduce the vapor concentration proceed as follows: Drive the vehicle for an additional 30 minutes avoiding driving conditions that will produce excessive fuel movement. Repeat Step 10. If the 0.020 inch EVAP Test is still not activated, repeat the Drive Cycle from Step 6. Using WDS, check for and clear flagged DTCs.
9 10
11 12 13
COMPREHENSIVE COMPONENT MONITOR ENGINE MANAGEMENT DRIVE CYCLE To avoid unnecessary complexity, a single comprehensive engine management drive cycle has not developed for X-TYPE. Refer to the individual DTC for specific drive cycle / monitoring conditions.
COMPREHENSIVE COMPONENT MONITOR TRANSMISSION DRIVE CYCLE The Comprehensive Component Monitor transmission drive cycle will check all transmission system components. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Engine and transmission at normal operating temperature. Ignition OFF; ensure that SPORT mode is NOT selected. With gear selector in P and the ignition ON. Check gearshift interlock by attempting to move selector without pressing the brake pedal. Verify P state illumination. Press and hold the brake pedal. Move the gear selector to R. Verify R state illumination. Set the parking brake. Press and hold the brake pedal. Attempt to start the engine. The engine should not start. Move the gear selector to N. Verify N state illumination. Start the engine. With the hand brake set and the brake pedal pressed, move the gear selector to the remaining positions in the J Gate (D, 4, 3, 2) for five (5) seconds each. Verify the state illumination in each position. Move the gear selector back to 4. Verify 4 state illumination. Move the gear selector to D. Verify D state illumination. Move the gear selector to N. Verify N state illumination. Select R, release the brakes and drive the vehicle in Reverse for a short distance. Stop the vehicle. Select 2 and drive the vehicle up to 65 km/h (40 mph). Hold 65 km/h (40 mph) for a minimum of five (5) seconds. Select 3 and hold 65 km/h (40 mph) for a minimum of five (5) seconds. Select 4 and hold 65 km/h (40 mph) for a minimum of five (5) seconds. Select D and accelerate to a minimum speed of 80 km/h (50 mph). Hold 80 129 km/h (50 80 mph) for a minimum of 1.7 kilometers (1 mile). Stop the vehicle; do not switch OFF the engine. Use WDS Datalogger TOTAL NUMBER OF DTC SET to ensure that transmission DTC monitoring is complete.
DTC P0010
MONITORING CONDITIONS Idle engine 30 seconds Accelerate from stop through complete engine rpm range Coast to a stop Drive the vehicle steadily between 48 97 km/h (30 60 mph) for 5 minutes; coast to a stop Accelerate smoothly through complete accelerator pedal travel; coast to a stop Idle engine 30 seconds Idle engine 30 seconds Accelerate from stop through complete engine rpm range; coast to a stop Drive the vehicle steadily between 48 97 km/h (30 60 mph) for 5 minutes; coast to a stop Accelerate smoothly through complete accelerator pedal travel; coast to a stop Idle engine 30 seconds Heated oxygen sensors monitor drive cycle page 4 (Oxygen sensor heaters)
CK ENG 2
OTHER N
DEFAULT ACTION ECM Default: Bank 1 VVT hold current set at a constant value of 450 mA
CM PIN POSSIBLE CAUSES EN16 -109 VVT solenoid valve to ECM PWM drive circuit: open circuit, short circuit, high resistance VVT solenoid failure
P0020
EMS OBD II
ECM Default: Bank 2 VVT hold current set at a constant value of 450 mA
EN16 -110
VVT solenoid valve to ECM PWM drive circuit: open circuit, short circuit, high resistance VVT solenoid failure
P0031
EMS OBD II
HO2 Sensor heater control circuit low current bank 1, upstream (1/1)
ECM Default: Bank 1 closed loop fuel metering and adaptive fuel metering inhibited Canister purge inhibited Bank 1 upstream HO2S heater control circuit switched off
HO2 Sensor 1/1 heater power supply circuit: open circuit HO2 Sensor 1/1 heater control circuit: open circuit, high resistance HO2 Sensor 1/1 heater ground circuit(s) fault (EN16-029, EN16-030) HO2 Sensor 1/1 heater failure
DTC P0032
FAULT DESCRIPTION HO2 Sensor heater control circuit high current bank 1, upstream (1/1)
MONITORING CONDITIONS Heated oxygen sensors monitor drive cycle page 4 (Oxygen sensor heaters)
CK ENG 2
OTHER N
DEFAULT ACTION ECM Default: Bank 1 closed loop fuel metering and adaptive fuel metering inhibited Canister purge inhibited Bank 1 upstream HO2S heater control circuit switched off None
CM PIN POSSIBLE CAUSES EN16 -001 -002 -029 -030 HO2 Sensor 1/1 heater control circuit: short circuit to ground HO2 Sensor 1/1 heater ground circuit(s) fault (EN16-029, EN16-030) HO2 Sensor 1/1 heater failure
P0037
EMS OBD II
HO2 Sensor heater control circuit low resistance bank 1, downstream (1/2) HO2 Sensor heater control circuit high resistance bank 1, downstream (1/2) HO2 Sensor heater control circuit low current bank 2, upstream (2/1)
Heated oxygen sensors monitor drive cycle page 4 (Oxygen sensor heaters) Heated oxygen sensors monitor drive cycle page 4 (Oxygen sensor heaters) Heated oxygen sensors monitor drive cycle page 4 (Oxygen sensor heaters)
EN16 -092
HO2 Sensor 1/2 heater control circuit: short circuit to ground HO2 Sensor 1/2 heater failure HO2 Sensor 1/2 heater control circuit: open circuit; high resistance HO2 Sensor 1/2 heater failure HO2 Sensor 2/1 heater power supply circuit: open circuit HO2 Sensor 2/1 heater control circuit: open circuit, high resistance HO2 Sensor 2/1 heater ground circuit(s) fault (EN16-081, EN16-082) HO2 Sensor 2/1 heater failure
P0038
EMS OBD II
None
EN16 -092
P0051
EMS OBD II
ECM Default: Bank 2 closed loop fuel metering and adaptive fuel metering inhibited Canister purge inhibited Bank 2 upstream HO2S heater control circuit switched off ECM Default: Bank 2 closed loop fuel metering and adaptive fuel metering inhibited Canister purge inhibited Bank 2 upstream HO2S heater control circuit switched off
P0052
EMS OBD II
HO2 Sensor heater control circuit high current bank 2, upstream (2/1)
Heated oxygen sensors monitor drive cycle page 4 (Oxygen sensor heaters)
HO2 Sensor 2/1 heater control circuit: short circuit to ground HO2 Sensor 2/1 heater ground circuit(s) fault (EN16-081, EN16-082) HO2 Sensor 2/1 heater failure
10
DTC P0057
FAULT DESCRIPTION HO2 Sensor heater control circuit low resistance bank 2, downstream (2/2) HO2 Sensor heater control circuit high resistance bank 2, downstream (2/2) MAF Sensor circuit range / performance
MONITORING CONDITIONS Heated oxygen sensors monitor drive cycle page 4 (Oxygen sensor heaters) Heated oxygen sensors monitor drive cycle page 4 (Oxygen sensor heaters) Fuel level > 25%. Start engine and bring to normal operating temperature > 82 C (180 F) Drive the vehicle steadily in 4th or 5th gear on a level road between 1700 2300 rpm; hold the engine speed constant for 40 seconds while maintaining a steady throttle
CK ENG 2
OTHER N
CM PIN POSSIBLE CAUSES EN16 -93 HO2 Sensor 2/2 heater control circuit: short circuit to ground HO2 Sensor 2/2 heater failure HO2 Sensor 2/2 heater control circuit: open circuit; high resistance HO2 Sensor 2/2 heater failure Blocked air cleaner Air intake leak Engine breather leak Throttle control malfunction MAF Sensor to ECM sensing circuit: high resistance, intermittent short circuit to ground MAF Sensor supply circuit: high resistance MAF Sensor failure
P0058
EMS OBD II
None
EN16 -93
P0101
EMS OBD II
ECM Default: Default air mass used Adaptive fuel metering inhibited Catalyst warm up ignition retard inhibited Canister purge inhibited Maximum engine speed reduced
EN16 -044
P0102
EMS OBD II
Ignition ON 10 seconds
ECM Default: Default air mass used Adaptive fuel metering inhibited Catalyst warm up ignition retard inhibited Canister purge inhibited Maximum engine speed reduced
EN16 -044
Blocked air cleaner MAF Sensor to ECM sensing circuit: high resistance, open circuit, intermittent short circuit to ground MAF Sensor supply circuit: open circuit, short circuit to ground MAF Sensor failure
11
DTC P0103
CK ENG 2
OTHER A
DEFAULT ACTION ECM Default: Default air mass used Adaptive fuel metering inhibited Catalyst warm up ignition retard inhibited Canister purge inhibited Maximum engine speed reduced ECM Default: Default value of 1.013 BAR (29.92 in hg) used
CM PIN POSSIBLE CAUSES EN16 -044 -045 -046 MAF Sensor to ECM sensing circuit: short circuit to B+ voltage MAF Sensor to ECM sensor ground circuit: open circuit MAF Sensor failure
P0105
EMS OBD II
Fuel level > 25% Start engine and bring to normal operating temperature > 82 C (180 F) Drive the vehicle steadily in 4th or 5th gear on a level road between 1700 2300 rpm; hold the engine speed constant for 40 seconds while maintaining a steady throttle Engine temperature cool (cooling fans not running) Remove ignition key for 20 seconds (cooling fans not running) Ignition key in, position II for 5 seconds (do not start) Repeat cycle twice more Ignition ON 10 seconds
EN16 -127
P0106
EMS OBD II
P0107
EMS OBD II
12
DTC P0108
FAULT DESCRIPTION
MONITORING CONDITIONS
CK ENG 2
OTHER N
DEFAULT ACTION ECM Default: Default value of 1 BAR (29.53 in hg) used ECM Default: Default value of 25 C (77 F) used
P0111
EMS OBD II
Engine OFF; coolant temperature <35 C (95 F) Start engine and hold 3000 rpm in P or N for 30 seconds
EN16 -071
Blocked air cleaner Air intake leak Engine breather leak IAT Sensor to ECM wiring: open circuit or high resistance IAT Sensor to ECM sensing circuit: short circuit to high voltage IAT Sensor failure IAT Sensor to ECM wiring: open circuit or high resistance IAT Sensor to ECM sensing circuit: short circuit to B+ voltage IAT Sensor failure IAT Sensor to ECM wiring: short circuit to ground IAT Sensor failure
P0112
EMS OBD II
Ignition ON 10 seconds
EN16 -071
P0113
EMS OBD II
Ignition ON 10 seconds
EN16 -071
13
DTC P0116
MONITORING CONDITIONS Engine coolant temperature and ambient temperature within 10 C (50 F) Drive the vehicle steadily in 4th or 5th gear above 1700 rpm for 5 minutes Idle engine until engine coolant temperature reaches 80 C (176 F) CAUTION: Overheating is possible if the ECT sensor is faulty and cooling fans do not operate Ignition ON 10 seconds
CK ENG 2
OTHER A
DEFAULT ACTION ECM Default: EOT value substituted (no greater than 95 C (203 F) Closed loop fuel metering inhibited Adaptive fuel metering inhibited Catalyst warm-up ignition retard inhibited Canister purge inhibited Maximum engine speed reduced ECM Default: EOT value substituted (no greater than 95 C (203 F) Closed loop fuel metering inhibited Adaptive fuel metering inhibited Catalyst warm-up ignition retard inhibited Canister purge inhibited Maximum engine speed reduced
CM PIN POSSIBLE CAUSES EN16 -070 Low coolant level Contaminated coolant Engine thermostat failure ECT Sensor to ECM sensing circuit: high resistance when hot, intermittent high resistance ECT Sensor failure
P0117
EMS OBD II
EN16 -070
ECT Sensor disconnected ECT Sensor to ECM sensing circuit: high resistance, open circuit, short circuit to B+ voltage ECT Sensor failure
14
DTC P0118
FAULT DESCRIPTION ECT Sensor circuit low voltage (high coolant temperature)
CK ENG 2
OTHER A
DEFAULT ACTION ECM Default: EOT value substituted (no greater than 95 C (203 F) Closed loop fuel metering inhibited Adaptive fuel metering inhibited Catalyst warm-up ignition retard inhibited Canister purge inhibited Maximum engine speed reduced ECM Default: Throttle motor and throttle motor relay disabled Throttle valve opening set to default value Idle speed controlled by fuel injection intervention Idle speed adaption inhibited ECM Default: Throttle motor and throttle motor relay disabled Throttle valve opening set to default value Idle speed controlled by fuel injection intervention Idle speed adaption inhibited
CM PIN POSSIBLE CAUSES EN16 -070 Engine overheat condition ECT Sensor to ECM wiring: short circuit to ground ECT Sensor failure
P0121
EMS OBD II
Battery voltage > 10 v Ignition ON Slowly press accelerator pedal to the floor over a 5 second period Slowly return the pedal to rest Repeat 3 times
TP Sensor to ECM wiring: open circuit, high resistance TP Sensor to ECM sensing circuits (TP1 or TP2): short circuit to B+ voltage TP Sensor failure
P0122
EMS OBD II
Battery voltage > 10 v Ignition ON Slowly press accelerator pedal to the floor over a 5 second period Slowly return the pedal to rest Repeat 3 times
EN16 -075
TP Sensor to ECM sensing circuit (TP1): open circuit, high resistance TP Sensor failure
15
DTC P0123
MONITORING CONDITIONS Battery voltage > 10 v Ignition ON Slowly press accelerator pedal to the floor over a 5 second period Slowly return the pedal to rest Repeat 3 times
CK ENG 2
OTHER R
DEFAULT ACTION ECM Default: Throttle motor and throttle motor relay disabled Throttle valve opening set to default value Idle speed controlled by fuel injection intervention Idle speed adaption inhibited ECM Default: EOT value substituted (no greater than 95 C (203 F) Closed loop fuel metering inhibited Adaptive fuel metering inhibited Catalyst warm-up ignition retard inhibited Canister purge inhibited Maximum engine speed reduced None
CM PIN POSSIBLE CAUSES EN16 -075 TP Sensor to ECM sensing circuit (TP1): short circuit to high voltage TP Sensor failure
P0125
EMS OBD II
ECT Sensor response (for closed loop fuel control) (Coolant thermostat monitor)
Engine coolant temperature and ambient temperature within 10 C (50 F) Drive the vehicle steadily in 4th or 5th gear above 1700 rpm for 5 minutes Idle engine until engine coolant temperature reaches 80 C (176 F) CAUTION: Overheating is possible if the ECT sensor is faulty and cooling fans do not operate Engine OFF; coolant temperature <35 C (95 F) Start engine and drive until normal engine operating temperature > 82 C (180 F) Heated oxygen sensors monitor drive cycle page 4 (Upstream oxygen sensors)
EN16 -070
Low coolant level Contaminated coolant Engine coolant thermostat failure ECT Sensor to ECM sensing circuit: high resistance, open circuit or short circuit to high voltage Engine cooling fan stuck on high speed Above normal air flow through engine compartment due to accident damage and/ or missing panels
P0128
EMS OBD II
Contaminated coolant Engine coolant thermostat failure ECT Sensor failure (ECT Sensor DTC(s) also flagged) HO2 Sensor 1/1 disconnected HO2 Sensor 1/1 to ECM variable current circuit fault (HO2 Sensor pin 3) ECM to HO2 Sensor 1/1 constant current circuit fault (HO2 Sensor pin 4) HO2 Sensor 1/1 failure
16
P0131
EMS OBD II
HO2 Sensor sense circuit low current bank 1, upstream (1/1) (Universal oxygen sensor: lean condition at ECM high current at sensor)
None
DTC P0132
FAULT DESCRIPTION HO2 Sensor sense circuit high current bank 1, upstream (1/1) (Universal oxygen sensor: rich condition at ECM low current at sensor)
MONITORING CONDITIONS Heated oxygen sensors monitor drive cycle page 4 (Upstream oxygen sensors)
CK ENG 2
OTHER N
CM PIN POSSIBLE CAUSES EN16 -083 -084 HO2 Sensor 1/1 disconnected HO2 Sensor 1/1 to ECM variable current circuit fault (HO2 Sensor pin 3) ECM to HO2 Sensor 1/1 constant current circuit fault (HO2 Sensor pin 4) HO2 Sensor 1/1 failure Engine misfire HO2 Sensor 1/1 disconnected HO2 Sensor 1/1 mechanical damage HO2 Sensor 1/1 to ECM wiring fault HO2 Sensor 1/1 short circuit to ground HO2 Sensor 1/1 to ECM wiring shield open circuit HO2 Sensor 1/1 heater circuit fault Exhaust leak Low exhaust temperature Injector flow partially blocked Catalyst efficiency decrease HO2 Sensor 1/1 failure HO2 Sensor 1/2 disconnected HO2 Sensor 1/2 to ECM wiring open circuit HO2 Sensor 1/2 short circuit to ground HO2 Sensor 1/2 failure HO2 Sensor 1/2 sensing circuit: short circuit to high voltage HO2 Sensor 1/2 ground (BRD braided shield) open circuit HO2 Sensor 1/2 failure
P0133
EMS OBD II
Heated oxygen sensors monitor drive cycle page 4 (Upstream oxygen sensors)
ECM Default: Bank 1 closed loop fuel metering inhibited Canister purge inhibited
P0137
EMS OBD II
Heated oxygen sensors monitor drive cycle page 4 (Downstream oxygen sensors) Heated oxygen sensors monitor drive cycle page 4 (Downstream oxygen sensors)
None
EN16 -128
P0138
EMS OBD II
None
EN16 -128
17
DTC P0140
FAULT DESCRIPTION HO2 Sensor sense circuit no activity bank 1, downstream (1/2)
MONITORING CONDITIONS Heated oxygen sensors monitor drive cycle page 4 (Downstream oxygen sensors)
CK ENG 2
OTHER N
CM PIN POSSIBLE CAUSES EN16 -128 HO2 Sensor 1/2 disconnected HO2 Sensor 1/2 mechanical damage HO2 Sensor 1/2 to ECM wiring open circuit HO2 Sensor 1/2 sensing circuit: short circuit to high voltage HO2 Sensor 1/2 short circuit to ground HO2 Sensor 1/2 ground (BRD braided shield) open circuit Exhaust leak Low exhaust temperature HO2 Sensor 1/2 failure HO2 Sensor 2/1 disconnected HO2 Sensor 2/1 to ECM variable current circuit fault (HO2 Sensor pin 3) ECM to HO2 Sensor 2/1 constant current circuit fault (HO2 Sensor pin 4) HO2 Sensor 2/1 failure HO2 Sensor 2/1 disconnected HO2 Sensor 2/1 to ECM variable current circuit fault (HO2 Sensor pin 3) ECM to HO2 Sensor 2/1 constant current circuit fault (HO2 Sensor pin 4) HO2 Sensor 2/1 failure
P0151
EMS OBD II
HO2 Sensor sense circuit low current bank 2, upstream (2/1) (Universal oxygen sensor: lean condition at ECM high current at sensor)
Heated oxygen sensors monitor drive cycle page 4 (Upstream oxygen sensors)
None
P0152
EMS OBD II
HO2 Sensor sense circuit high current bank 2, upstream (2/1) (Universal oxygen sensor: rich condition at ECM low current at sensor)
Heated oxygen sensors monitor drive cycle page 4 (Upstream oxygen sensors)
None
18
DTC P0153
FAULT DESCRIPTION HO2 Sensor sense circuit slow response bank 2, upstream (2/1)
MONITORING CONDITIONS Heated oxygen sensors monitor drive cycle page 4 (Upstream oxygen sensors)
CK ENG 2
OTHER N
DEFAULT ACTION ECM Default: Bank 1 closed loop fuel metering inhibited Canister purge inhibited
CM PIN POSSIBLE CAUSES EN16 -107 -108 Engine misfire HO2 Sensor 2/1 disconnected HO2 Sensor 2/1 mechanical damage HO2 Sensor 2/1 to ECM wiring fault HO2 Sensor 2/1 short circuit to ground HO2 Sensor 2/1 to ECM wiring shield open circuit HO2 Sensor 2/1 heater circuit fault Exhaust leak Low exhaust temperature Injector flow partially blocked Catalyst efficiency decrease HO2 Sensor 2/1 failure HO2 Sensor 2/2 disconnected HO2 Sensor 2/2 to ECM wiring open circuit HO2 Sensor 2/2 short circuit to ground HO2 Sensor 2/2 failure HO2 Sensor 2/2 sensing circuit: short circuit to high voltage HO2 Sensor 2/2 ground (BRD braided shield) open circuit HO2 Sensor 2/2 failure
P0157
EMS OBD II
Heated oxygen sensors monitor drive cycle page 4 (Downstream oxygen sensors) Heated oxygen sensors monitor drive cycle page 4 (Downstream oxygen sensors)
None
EN16 -129
P0158
EMS OBD II
None
EN16 -129
19
DTC P0160
FAULT DESCRIPTION HO2 Sensor sense circuit no activity bank 2, downstream (2/2)
MONITORING CONDITIONS Heated oxygen sensors monitor drive cycle page 4 (Downstream oxygen sensors)
CK ENG 2
OTHER N
CM PIN POSSIBLE CAUSES EN16 -129 HO2 Sensor 2/2 disconnected HO2 Sensor 2/2 mechanical damage HO2 Sensor 2/2 to ECM wiring open circuit HO2 Sensor 2/2 sensing circuit short circuit to high voltage HO2 Sensor 2/2 short circuit to ground HO2 Sensor 2/2 ground (BRD braided shield) open circuit Exhaust leak Low exhaust temperature HO2 Sensor 2/2 failure Engine misfire Air intake leak between MAF Sensor and throttle Fuel filter / system restriction Fuel injector restriction Fuel pressure sensor failure (low fuel pressure) Low fuel pump output HO2 Sensor(s) (1/1, 1/2) harness wiring condition fault Exhaust leak (before catalyst) ECM receiving incorrect signal from one or more of the following components: ECT Sensor, MAF Sensor, IAT Sensor, IP Sensor, EFT Sensor, TP Sensor
P0171
EMS OBD II
Start engine and bring to normal operating temperature > 82 C (180 F) Idle for 10 minutes
ECM Default: Bank 1 catalyst warm-up ignition retard inhibited Bank 1 closed loop fuel metering inhibited Canister purge inhibited Maximum engine speed reduced
20
DTC P0172
MONITORING CONDITIONS Start engine and bring to normal operating temperature > 82 C (180 F) Idle for 10 minutes
CK ENG 2
OTHER A
DEFAULT ACTION ECM Default: Bank 1 catalyst warm-up ignition retard inhibited Bank 1 closed loop fuel metering inhibited Canister purge inhibited Maximum engine speed reduced ECM Default: Bank 2 catalyst warm-up ignition retard inhibited Bank 2 closed loop fuel metering inhibited Canister purge inhibited Maximum engine speed reduced
CM PIN POSSIBLE CAUSES Restricted air filter Leaking fuel injector(s) Fuel pressure sensor failure (high fuel pressure) ECM receiving incorrect signal from one or more of the following components: ECT Sensor, MAF Sensor, IAT Sensor, IP Sensor, EFT Sensor, TP Sensor Engine misfire Air intake leak between MAF Sensor and throttle Fuel filter / system restriction Fuel injector restriction Fuel pressure sensor failure (low fuel pressure) Low fuel pump output HO2 Sensor(s) (2/1, 2/2) harness wiring condition fault Exhaust leak (before catalyst) ECM receiving incorrect signal from one or more of the following components: ECT Sensor, MAF Sensor, IAT Sensor, IP Sensor, EFT Sensor, TP Sensor Restricted air filter Leaking fuel injector(s) Fuel pressure sensor failure (high fuel pressure) ECM receiving incorrect signal from one or more of the following components: ECT Sensor, MAF Sensor, IAT Sensor, IP Sensor, EFT Sensor, TP Sensor
P0174
EMS OBD II
Start engine and bring to normal operating temperature > 82 C (180 F) Idle for 10 minutes
P0175
EMS OBD II
Start engine and bring to normal operating temperature > 82 C (180 F) Idle for 10 minutes
ECM Default: Bank 2 catalyst warm-up ignition retard inhibited Bank 2 closed loop fuel metering inhibited Canister purge inhibited Maximum engine speed reduced
21
DTC P0181
MONITORING CONDITIONS Engine OFF; coolant temperature <35 C (95 F) Start engine and drive until normal engine operating temperature > 82 C (180 F) Drive for an additional 25 minutes Ignition ON 10 seconds
CK ENG 2
OTHER N
CM PIN POSSIBLE CAUSES EN16 -050 EFT Sensor to ECM sensing circuit: high resistance, open circuit, short circuit to ground short circuit to high voltage EFT Sensor to splice sensor ground circuit: high resistance, open circuit EFT Sensor failure
P0182
EMS OBD II
EN16 -050
EFT Sensor to ECM sensing circuit: short circuit to ground EFT Sensor to splice sensor ground circuit: short circuit EFT Sensor failure EFT Sensor disconnected EFT Sensor to ECM sensing circuit: high resistance, open circuit, short circuit to high voltage EFT Sensor to splice sensor ground circuit: high resistance, open circuit EFT Sensor failure Fuel filter / system restriction Fuel system leak Incorrect fuel pump output IP Sensor to ECM sensing circuit: high resistance, open circuit, short circuit to ground, short circuit to high voltage IP Sensor to splice sensor supply circuit: high resistance, open circuit IP Sensor to splice sensor ground circuit: high resistance, open circuit, short circuit to ground, short circuit to high voltage IP Sensor failure
P0183
EMS OBD II
Ignition ON 10 seconds
EN16 -050
P0191
EMS OBD II
Fuel level > 25% Idle engine 30 seconds Accelerate from stop through complete engine rpm range; coast to a stop Drive the vehicle steadily between 48 97 km/h (30 60 mph) for 5 minutes; coast to a stop Accelerate smoothly through complete accelerator pedal travel; coast to a stop Idle engine 30 seconds
ECM Default: Default value of 3.80 BAR (55.11 psi) used Fuel pump feedback control inhibited
EN16 -073
22
DTC P0192
CK ENG 2
OTHER N
DEFAULT ACTION ECM Default: Default value of 3.80 BAR (55.11 psi) used Fuel pump feedback control inhibited
CM PIN POSSIBLE CAUSES EN16 -073 IP Sensor disconnected IP Sensor to ECM sensing circuit: open circuit or short circuit to ground IP Sensor to splice sensor supply circuit: high resistance open circuit IP Sensor failure IP Sensor to ECM wiring (supply, sense): short circuit to each other IP Sensor to ECM sense circuit: short circuit to high voltage IP Sensor to splice sensor ground circuit: open circuit IP Sensor failure EOT Sensor to ECM sensing circuit; high resistance when hot, intermittent high resistance EOT Sensor failure
P0193
EMS OBD II
Ignition ON 10 seconds
ECM Default: Default value of 3.80 BAR (55.11 psi) used Fuel pump feedback control inhibited
EN16 -073
P0196
EMS OBD II
Engine OFF; coolant temperature <35 C (95 F) Start engine and drive until normal engine operating temperature > 82 C (180 F) Ignition ON 10 seconds
EN16 -078
P0197
EN16 -078
EOT Sensor to ECM sensing circuit: short circuit to ground EOT Sensor failure EOT Sensor disconnected EOT Sensor to ECM sensing circuit: high resistance, open circuit, short circuit to B+ voltage EOT Sensor failure
P0198
Ignition ON 10 seconds
EN16 -078
23
DTC P0201
MONITORING CONDITIONS Start engine Battery voltage > 12 v Idle for 2 minutes
CK ENG 2
OTHER A
DEFAULT ACTION ECM Default: Bank 1 closed loop fuel metering inhibited Bank 1 adaptive fuel metering inhibited Bank 1 catalyst warm up ignition retard inhibited Canister purge inhibited Maximum engine speed reduced ECM Default: Bank 2 closed loop fuel metering inhibited Bank 2 adaptive fuel metering inhibited Bank 2 catalyst warm up ignition retard inhibited Canister purge inhibited Maximum engine speed reduced ECM Default: Bank 1 closed loop fuel metering inhibited Bank 1 adaptive fuel metering inhibited Bank 1 catalyst warm up ignition retard inhibited Canister purge inhibited Maximum engine speed reduced
CM PIN POSSIBLE CAUSES EN16 -115 Injector disconnected Injector harness wiring: open circuit, short circuit Injector failure
P0202
EMS OBD II
EN16 -120
Injector disconnected Injector harness wiring: open circuit, short circuit Injector failure
P0203
EMS OBD II
EN16 -114
Injector disconnected Injector harness wiring: open circuit, short circuit Injector failure
24
DTC P0204
MONITORING CONDITIONS Start engine Battery voltage > 12 v Idle for 2 minutes
CK ENG 2
OTHER A
DEFAULT ACTION ECM Default: Bank 2 closed loop fuel metering inhibited Bank 2 adaptive fuel metering inhibited Bank 2 catalyst warm up ignition retard inhibited Canister purge inhibited Maximum engine speed reduced ECM Default: Bank 1 closed loop fuel metering inhibited Bank 1 adaptive fuel metering inhibited Bank 1 catalyst warm up ignition retard inhibited Canister purge inhibited Maximum engine speed reduced ECM Default: Bank 2 closed loop fuel metering inhibited Bank 2 adaptive fuel metering inhibited Bank 2 catalyst warm up ignition retard inhibited Canister purge inhibited Maximum engine speed reduced
CM PIN POSSIBLE CAUSES EN16 -119 Injector disconnected Injector harness wiring: open circuit, short circuit Injector failure
P0205
EMS OBD II
EN16 -113
Injector disconnected Injector harness wiring: open circuit, short circuit Injector failure
P0206
EMS OBD II
EN16 -118
Injector disconnected Injector harness wiring: open circuit, short circuit Injector failure
25
DTC P0222
MONITORING CONDITIONS Battery voltage > 10 v Ignition ON Slowly press accelerator pedal to the floor over a 5 second period Slowly return the pedal to rest Repeat 3 times
CK ENG 2
OTHER R
DEFAULT ACTION ECM Default: Throttle motor and throttle motor relay disabled Throttle valve opening set to default value Idle speed controlled by fuel injection intervention Idle speed adaption inhibited ECM Default: Throttle motor and throttle motor relay disabled Throttle valve opening set to default value Idle speed controlled by fuel injection intervention Idle speed adaption inhibited None
CM PIN POSSIBLE CAUSES EN16 -076 TP Sensor to ECM sensing circuit (TP2): open circuit, high resistance TP Sensor failure
P0223
EMS OBD II
Battery voltage > 10 v Ignition ON Slowly press accelerator pedal to the floor over a 5 second period Slowly return the pedal to rest Repeat 3 times
EN16 -076
TP Sensor to ECM sensing circuit (TP2): short circuit to high voltage TP Sensor failure
P0300
EMS OBD II
1 or 2*
Cylinder compression low Worn camshaft / broken valve spring(s) Fuel delivery pressure (low / high) Fuel injector(s) restricted / leaking Fuel injector(s) continuously open Fuel contamination Fuel injector circuit fault(s) (Injector DTCs also flagged) Spark plug failure / fouled / incorrect gap ECM to ignition coil primary circuit fault (Cylinder misfire detected DTC also flagged) Ignition coil failure
26
DTC P0301
SYS EMS OBD II EMS OBD II EMS OBD II EMS OBD II EMS OBD II EMS OBD II EMS OBD II
FAULT DESCRIPTION Misfire detected cylinder 1 *Refer to Misfire Note, page 5 Misfire detected cylinder 2 *Refer to Misfire Note, page 5 Misfire detected cylinder 3 *Refer to Misfire Note, page 5 Misfire detected cylinder 4 *Refer to Misfire Note, page 5 Misfire detected cylinder 5 *Refer to Misfire Note, page 5 Misfire detected cylinder 6 *Refer to Misfire Note, page 5 KS sense circuit out of range low voltage
MONITORING CONDITIONS Misfire monitor drive cycle page 5 Misfire monitor drive cycle page 5 Misfire monitor drive cycle page 5 Misfire monitor drive cycle page 5 Misfire monitor drive cycle page 5 Misfire monitor drive cycle page 5 Start engine Battery voltage > 12 v Idle for 2 minutes
CK ENG 1 or 2*
OTHER N
P0302
1 or 2*
None
P0303
1 or 2*
None
P0304
1 or 2*
None
P0305
1 or 2*
None
P0306
1 or 2*
None
P0332
ECM Default: Maximum ignition retard Maximum engine speed reduced ECM Default: Maximum ignition retard Maximum engine speed reduced
EN16 -098
Poor sensor contact with the cylinder block KS to ECM sense circuit short circuit to ground KS failure Poor sensor contact with the cylinder block KS to ECM sense circuit: high resistance, open circuit, short circuit to high voltage KS failure
P0333
EMS OBD II
EN16 -098
27
DTC P0335
MONITORING CONDITIONS Start engine; momentarily race the engine; stop engine Repeat two additional times Start engine; idle 30 seconds. Accelerate from stop through complete engine rpm range; coast to a stop Drive the vehicle steadily between 48 97 km/h (30 60 mph) for 5 minutes; coast to a stop Accelerate smoothly through complete accelerator pedal travel; coast to a stop Idle engine 30 seconds Note: If CKP Sensor fault exists and engine will not start, battery voltage must drop below 10.5 V during cranking for DTC to be flagged. (Crank period 30 seconds.) If CKP Sensor fault exists, engine will start on the second crank as the ECM will default to CMP signals for synchronization.
CK ENG 2
OTHER A
CM PIN POSSIBLE CAUSES EN16 -036 -037 CKP Sensor disconnected CKP Sensor gap incorrect / foreign matter on sensor face CKP Sensor sensing circuit: open circuit, short circuit to ground, short circuit to high voltage CKP Sensor failure
28
DTC P0336
MONITORING CONDITIONS Start engine; momentarily race the engine; stop engine Repeat two additional times Start engine; idle 30 seconds Accelerate from stop through complete engine rpm range; coast to a stop Drive the vehicle steadily between 48 97 km/h (30 60 mph) for 5 minutes; coast to a stop Accelerate smoothly through complete accelerator pedal travel; coast to a stop Idle engine 30 seconds Start engine; momentarily race the engine; stop engine Repeat two additional times Start engine idle 30 seconds Accelerate from stop through complete engine rpm range; coast to a stop Drive the vehicle steadily between 48 97 km/h (30 60 mph) for 5 minutes; coast to a stop Accelerate smoothly through complete accelerator pedal travel; coast to a stop Idle engine 30 seconds
CK ENG 2
OTHER A
CM PIN POSSIBLE CAUSES EN16 -036 -037 CKP Sensor reluctor: foreign matter / damaged teeth CKP Sensor sensing circuit: intermittent open circuit, short circuit to ground, short circuit to high voltage CKP Sensor failure
P0340
EMS OBD II
None
CMP Sensor disconnected CMP Sensor gap incorrect / foreign matter on sensor face CMP Sensor sensing circuit: open circuit, short circuit to ground, short circuit to high voltage CMP Sensor 1 failure
29
DTC P0341
MONITORING CONDITIONS Start engine; momentarily race the engine; stop engine Repeat two additional times Start engine; idle 30 seconds Accelerate from stop through complete engine rpm range; coast to a stop Drive the vehicle steadily between 48 97 km/h (30 60 mph) for 5 minutes; coast to a stop Accelerate smoothly through complete accelerator pedal travel; coast to a stop Idle engine 30 seconds Start engine Battery voltage > 12 v Idle for 2 minutes
CK ENG 2
OTHER N
CM PIN POSSIBLE CAUSES EN16 -094 -095 CMP Sensor disconnected CMP Sensor gap incorrect / foreign matter on sensor face CMP Sensor sensing circuit: open circuit, short circuit to ground, short circuit to high voltage CMP Sensor 1 failure
P0351
EMS OBD II
ECM Default: Bank 1 closed loop fuel metering inhibited Bank 1 adaptive fuel metering inhibited Bank 1 catalyst warm up ignition retard inhibited Canister purge inhibited Maximum engine speed reduced Fuel injection cut off (cylinder 1)
EN16 -087
ECM to ignition module primary circuit: open circuit, short circuit to ground, high resistance Ignition module ground circuit: open circuit, high resistance Ignition module / coil failure
30
DTC P0352
MONITORING CONDITIONS Start engine Battery voltage > 12 v Idle for 2 minutes
CK ENG 2
OTHER A
DEFAULT ACTION ECM Default: Bank 2 closed loop fuel metering inhibited Bank 2 adaptive fuel metering inhibited Bank 2 catalyst warm up ignition retard inhibited Canister purge inhibited Maximum engine speed reduced Fuel injection cut off (cylinder 2) ECM Default: Bank 1 closed loop fuel metering inhibited Bank 1 adaptive fuel metering inhibited Bank 1 catalyst warm up ignition retard inhibited Canister purge inhibited Maximum engine speed reduced Fuel injection cut off (cylinder 3)
CM PIN POSSIBLE CAUSES EN16 -061 ECM to ignition module primary circuit: open circuit, short circuit to ground, high resistance Ignition module ground circuit: open circuit, high resistance Ignition module / coil failure
P0353
EMS OBD II
EN16 -088
ECM to ignition module primary circuit: open circuit, short circuit to ground, high resistance Ignition module ground circuit: open circuit, high resistance Ignition module / coil failure
31
DTC P0354
MONITORING CONDITIONS Start engine Battery voltage > 12 v Idle for 2 minutes
CK ENG 2
OTHER A
DEFAULT ACTION ECM Default: Bank 2 closed loop fuel metering inhibited Bank 2 adaptive fuel metering inhibited Bank 2 catalyst warm up ignition retard inhibited Canister purge inhibited Maximum engine speed reduced Fuel injection cut off (cylinder 4) ECM Default: Bank 1 closed loop fuel metering inhibited Bank 1 adaptive fuel metering inhibited Bank 1 catalyst warm up ignition retard inhibited Canister purge inhibited Maximum engine speed reduced Fuel injection cut off (cylinder 5)
CM PIN POSSIBLE CAUSES EN16 -062 ECM to ignition module primary circuit: open circuit, short circuit to ground, high resistance Ignition module ground circuit: open circuit, high resistance Ignition module / coil failure
P0355
EMS OBD II
EN16 -089
ECM to ignition module primary circuit: open circuit, short circuit to ground, high resistance Ignition module ground circuit: open circuit, high resistance Ignition module / coil failure
32
DTC P0356
MONITORING CONDITIONS Start engine Battery voltage > 12 v Idle for 2 minutes
CK ENG 2
OTHER A
DEFAULT ACTION ECM Default: Bank 2 closed loop fuel metering inhibited Bank 2 adaptive fuel metering inhibited Bank 2 catalyst warm up ignition retard inhibited Canister purge inhibited Maximum engine speed reduced Fuel injection cut off (cylinder 6) None
CM PIN POSSIBLE CAUSES EN16 -063 ECM to ignition module primary circuit: open circuit, short circuit to ground, high resistance Ignition module ground circuit: open circuit, high resistance Ignition module / coil failure
P0420
EMS OBD II
HO2 Sensor disconnected HO2 Sensor to ECM wiring fault HO2 Sensor heater to ECM wiring fault HO2 Sensor heater failure Upstream HO2 Sensor failure Downstream HO2 Sensor failure Catalyst failure HO2 Sensor disconnected HO2 Sensor to ECM wiring fault HO2 Sensor heater to ECM wiring fault HO2 Sensor heater failure Upstream HO2 Sensor failure Downstream HO2 Sensor failure Catalyst failure
P0430
EMS OBD II
None
33
DTC P0442
CK ENG 2
OTHER N
DEFAULT ACTION ECM Default: Canister purge inhibited Adaptive fuel metering inhibited
CM PIN POSSIBLE CAUSES Fuel cap seal defective EVAP system leak (canister damage, pipework damage) EVAP Canister purge valve to ECM drive circuit: open circuit, short circuit, high resistance EVAP Canister purge valve power supply circuit: open circuit, short circuit EVAP Canister purge valve to engine purge pipe: restricted, leaking, disconnected EVAP Canister purge valve operating vacuum hose leak / restriction EVAP Canister purge valve failure Fuel tank leak EVAP Canister purge valve to ECM drive circuit: open circuit, short circuit, high resistance EVAP Canister purge valve power supply circuit: open circuit, short circuit EVAP Canister purge valve operating vacuum hose leak / restriction EVAP Canister purge valve failure EVAP Canister purge valve disconnected EVAP Canister purge valve to ECM drive circuit: open circuit, high resistance EVAP Canister purge valve failure EVAP Canister purge valve to ECM drive circuit: short circuit to ground EVAP Canister purge valve failure
P0443
EMS OBD II
EN16 -066
P0444
EMS OBD II
ECM Default: Canister purge inhibited Adaptive fuel metering inhibited ECM Default: Canister purge inhibited Adaptive fuel metering inhibited
EN16 -066
P0445
EMS OBD II
EN16 -066
34
DTC P0446
CK ENG 2
OTHER N
DEFAULT ACTION ECM Default: Canister purge inhibited Adaptive fuel metering inhibited
CM PIN POSSIBLE CAUSES EN16 -067 EVAP canister close valve power supply circuit: open circuit, short circuit EVAP canister close valve to ECM drive circuit: open circuit, high resistance, short circuit to B+ voltage EVAP canister close valve failure EVAP canister close valve power supply circuit: open circuit, short circuit EVAP canister close valve to ECM drive circuit: open circuit, high resistance, short circuit to B+ voltage EVAP canister close valve failure EVAP canister close valve to ECM drive circuit: short to ground EVAP canister close valve failure
P0447
EMS OBD II
Ignition ON 10 seconds
EN16 -067
P0448
EMS OBD II
Ignition ON 10 seconds
ECM Default: Canister purge inhibited Adaptive fuel metering inhibited None
EN16 -067
P0450
EMS OBD II
EN16 -104
FTP Sensor disconnected FTP Sensor to ECM sense circuit: open circuit, short circuit to ground, short circuit to B+ voltage FTP Sensor to splice sensor supply circuit: open circuit, high resistance FTP Sensor to splice ground circuit: open circuit, high resistance FTP Sensor failure FTP Sensor disconnected FTP Sensor to ECM sense circuit: open circuit, short circuit to ground FTP Sensor to splice sensor supply circuit: open circuit, high resistance FTP Sensor failure
P0452
EMS OBD II
Ignition ON 10 seconds
None
EN16 -104
35
DTC P0453
CK ENG 2
OTHER N
CM PIN POSSIBLE CAUSES EN16 -104 FTP Sensor to splice sensor ground circuit: open circuit, high resistance FTP Sensor to ECM sense circuit: short circuit to high voltage FTP Sensor failure Fuel cap off Fuel cap seal defective EVAP system leak (canister damage, pipework damage) EVAP Canister purge valve to ECM drive circuit: open circuit, short circuit, high resistance EVAP Canister purge valve power supply circuit: open circuit, short circuit EVAP Canister purge valve to engine purge pipe: restricted, leaking, disconnected EVAP Canister purge valve operating vacuum hose leak / restriction EVAP Canister purge valve failure Fuel tank leak
P0455
EMS OBD II
36
DTC P0456
FAULT DESCRIPTION EVAP system leak detected very small (0.020 in.)
CK ENG 2
OTHER N
DEFAULT ACTION ECM Default: Canister purge inhibited Adaptive fuel metering inhibited
CM PIN POSSIBLE CAUSES Fuel cap seal defective EVAP system leak (canister damage, pipework damage) EVAP Canister purge valve to ECM drive circuit: open circuit, short circuit, high resistance EVAP Canister purge valve power supply circuit: open circuit, short circuit EVAP Canister purge valve to engine purge pipe: restricted, leaking EVAP Canister purge valve operating vacuum hose leak / restriction EVAP Canister purge valve failure Fuel tank leak Fuel level sensor to instrument pack circuit(s): intermittent short circuit, open circuit, high resistance Fuel level sensor failure Instrument pack fault (incorrect fuel level data) ECM to radiator cooling fan module drive circuit: short circuit, open circuit, high resistance Radiator cooling fan module fault
P0460
EMS OBD II
Fuel tank empty Fill in stages: 1/4, 1/2, 3/4, full Check fuel gauge reading at each stage Start and run engine > 2000 rpm for 2 minutes (Ensures voltage stays above 14 V for the required time)
None
P0480
EMS JAG
EN16 -051
37
DTC P0506
MONITORING CONDITIONS Start engine and drive until normal engine operating temperature > 82 C (180 F) Stop vehicle and idle 30 seconds Drive vehicle for 2 minutes Stop vehicle and idle 30 seconds Repeat drive / idle two additional times Start engine and drive until normal engine operating temperature > 82 C (180 F) Stop vehicle and idle 30 seconds Drive vehicle for 2 minutes Stop vehicle and idle 30 seconds Repeat drive / idle two additional times Engine temperature cool (cooling fans not running) Remove ignition key for 20 seconds (cooling fans not running) Ignition key in, position II for 5 seconds (do not start) Repeat cycle two additional times
CK ENG 2
OTHER N
CM PIN POSSIBLE CAUSES Air intake restriction Accessory drive overload (defective / seized component) Throttle valve stuck closed Throttle body failure
P0507
EMS OBD II
None
Intake air leak between MAF sensor and throttle Intake air leak between throttle and engine Engine crankcase breather leak Throttle valve stuck open Throttle body failure
P0560
EMS OBD II
None
EN16 -022
Note: This DTC can be flagged due to fuel injection pressure sensor fault. If P0193 is also flagged, correct first.
38
DTC P0565
CK ENG N
OTHER A
DEFAULT ACTION ECM Default: Speed control inhibited Maximum engine speed reduced
CM PIN POSSIBLE CAUSES EN16 -047 Cruise control switches internal steering wheel circuit: short circuit to ground Steering wheel cassette reel: short circuit to ground Cassette reel to ECM circuit: short circuit to ground ON / OFF switch failure (stuck ON) Cruise control switches internal steering wheel circuit: short circuit to ground Steering wheel cassette reel: short circuit to ground Cassette reel to ECM circuit: short circuit to ground CANCEL switch failure (stuck ON) Cruise control switches internal steering wheel circuit: short circuit to ground Steering wheel cassette reel: short circuit to ground Cassette reel to ECM circuit: short circuit to ground RESUME switch failure (stuck ON) Cruise control switches internal steering wheel circuit: open circuit; high resistance Steering wheel cassette reel open circuit, high resistance Cassette reel to ECM circuit: open circuit, high resistance
P0566
EMS JAG
Ignition ON 45 seconds
EN16 -047
P0567
EMS JAG
Ignition ON 45 seconds
EN16 -047
P0568
EMS JAG
Ignition ON 45 seconds
EN16 -047
39
DTC P0569
CK ENG N
OTHER A
DEFAULT ACTION ECM Default: Speed control inhibited Maximum engine speed reduced
CM PIN POSSIBLE CAUSES EN16 -047 Cruise control switches internal steering wheel circuit: short circuit to ground Steering wheel cassette reel: short circuit to ground Cassette reel to ECM circuit: short circuit to ground SET / - switch failure Cruise control switches internal steering wheel circuit: short circuit to ground Steering wheel cassette reel: short circuit to ground Cassette reel to ECM circuit: short circuit to ground SET / + switch failure ECM Failure
P0570
EMS JAG
Ignition ON 45 seconds
EN16 -047
P0603
EMS OBD II
Engine temperature cool (cooling fans not running) Remove ignition key for 20 seconds (cooling fans not running) Ignition key in, position II for 5 seconds (do not start) Repeat cycle two additional times. Ignition ON Battery voltage > 12 v Automatic P for 5 seconds; manual clutch fully pressed for 5 seconds Start engine
None
P0616
EMS OBD II
Starter relay drive circuit low voltage / starter relay request off (ignition switch position III OFF)
None
Starter relay drive circuit: open circuit, high resistance Starter relay failure
40
DTC P0617
FAULT DESCRIPTION Starter relay drive circuit high voltage / starter relay request on (ignition switch position III ON)
MONITORING CONDITIONS Ignition ON Battery voltage > 12 v Automatic P for 5 seconds; manual clutch fully pressed for 5 seconds Start engine Start engine Climate control system OFF Idle for 10 seconds Start engine Climate control system ON full cooling Idle for 2 minutes Comprehensive component monitor transmission drive cycle page 7
CK ENG 2
OTHER N
CM PIN POSSIBLE CAUSES EN16 -041 -006 Starter relay drive circuit: short circuit to high voltage Starter relay failure
P0646
EMS OBD II
A/C Compressor clutch relay drive circuit low voltage / A/C (compressor clutch request off [CAN]) A/C Compressor clutch relay drive circuit high voltage / A/C (compressor clutch request on [CAN]) Transmission range sensor circuit no signal; incorrect signal(s)
None
EN16 -034
A/C Compressor clutch relay drive circuit: open circuit, high resistance A/C Compressor clutch relay failure A/C Compressor clutch relay drive circuit: short circuit to high voltage A/C Compressor clutch relay failure
P0647
EMS OBD II
None
EN16 -034
P0706
TRANS OBD II
TCM Default: 4, 3, 2 Cannot be selected No J Gate illumination Reverse disengaged above 10 km/h (6 mph) (Poor shift quality)
J Gate incorrect setting Selector cable adjustment / installation incorrect Range sensor incorrect installation / adjustment Range sensor to TCM circuit(s): open circuit, short circuit to ground TCM Ground circuit: open circuit, high resistance Range sensor failure
41
DTC P0710
CK ENG 2
OTHER A
CM PIN POSSIBLE CAUSES JB131 -039 -020 Transmission to TCM temperature sensor circuit: open circuit, short circuit, high resistance Transmission internal temperature sensor circuit (internal harness): open circuit, short circuit; high resistance Sensor ground circuit fault TFT Sensor failure Transmission to TCM turbine speed sensor circuit: open circuit, short circuit, high resistance Transmission internal turbine speed sensor circuit: open circuit, short circuit, high resistance Transmission to TCM turbine speed sensor circuit: shielding defective Sensor ground circuit fault Turbine speed sensor failure Transmission to TCM output speed sensor circuit: open circuit, short circuit, high resistance Transmission internal output speed sensor circuit: open circuit, short circuit, high resistance Transmission to TCM output speed sensor circuit: shielding defective Sensor ground circuit fault Output speed sensor failure J Gate incorrect setting Transmission oil level low Transmission mechanical failure
P0715
TRANS OBD II
P0720
TRANS OBD II
TCM Default: ABS Wheel speed (CAN) substituted (Poor shift quality) If ABS Wheel speed message incorrect fixed 4th gear
P0731
TRANS OBD II
1st Gear ratio error Note: If a shift solenoid failure DTC is also flagged, correct shift solenoid DTC first.
42
DTC P0732
FAULT DESCRIPTION 2nd Gear ratio error Note: If a shift solenoid failure DTC is also flagged, correct shift solenoid DTC first.
CK ENG 2
OTHER A
CM PIN POSSIBLE CAUSES J Gate incorrect setting Transmission oil level low Transmission mechanical failure
P0733
TRANS OBD II
3rd Gear ratio error Note: If a shift solenoid failure DTC is also flagged, correct shift solenoid DTC first.
J Gate incorrect setting Transmission oil level low Transmission mechanical failure
P0734
TRANS OBD II
4th Gear ratio error Note: If a shift solenoid failure DTC is also flagged, correct shift solenoid DTC first.
J Gate incorrect setting Transmission oil level low Transmission mechanical failure
P0735
TRANS OBD II
5th Gear ratio error Note: If a shift solenoid failure DTC is also flagged, correct shift solenoid DTC first.
J Gate incorrect setting Transmission oil level low Transmission mechanical failure
P0736
TRANS JAG
Comprehensive component monitor transmission drive cycle page 7 Comprehensive component monitor transmission drive cycle page 7
TCM Default: Fixed 4th gear in D (R range not effected) TCM Default: No TCC control
J Gate incorrect setting Transmission oil level low Transmission mechanical failure J Gate incorrect setting Transmission oil level low Transmission mechanical failure
P0740
TRANS OBD II
TCC malfunction
43
DTC P0743
CK ENG 2
OTHER A
DEFAULT ACTION TCM Default: If short circuit to B+ V TCC permanently engaged If other cause TCC inoperative
CM PIN POSSIBLE CAUSES JB131 -016 -009 Transmission to TCM TCC solenoid circuit: open circuit, short circuit to B+ V, short circuit to ground Transmission internal TCC solenoid circuit: open circuit, short circuit TCM Ground circuit: open circuit, high resistance TCC Solenoid failure Transmission to TCM line pressure solenoid circuit: open circuit, short circuit Transmission internal line pressure solenoid circuit: open circuit, short circuit TCM Ground circuit: open circuit, high resistance Line pressure solenoid failure Transmission to TCM shift solenoid A circuit: open circuit, short circuit to B+ V, short circuit to ground Transmission internal shift solenoid A circuit: open circuit, short circuit TCM Ground circuit: open circuit, high resistance Shift solenoid A pressure solenoid failure Transmission to TCM shift solenoid B circuit: open circuit, short circuit to B+ V, short circuit to ground Transmission internal shift solenoid B circuit: open circuit, short circuit TCM Ground circuit: open circuit, high resistance Shift solenoid B pressure solenoid failure
P0748
TRANS OBD II
P0753
TRANS OBD II
TCM Default: If short circuit to B+ V fixed 2nd gear at low vehicle speed; fixed 5th gear at high vehicle speed If other cause fixed 3rd gear at low vehicle speed; fixed 4th gear at high vehicle speed TCM Default: If short circuit to B+ V: fixed 3nd gear If other cause: fixed 4rd gear
P0758
TRANS OBD II
44
DTC P0763
CK ENG 2
OTHER A
CM PIN POSSIBLE CAUSES JB131 -052 -009 Transmission to TCM shift solenoid C circuit: open circuit, short circuit to B+ V, short circuit to ground Transmission internal shift solenoid C circuit: open circuit, short circuit TCM Ground circuit: open circuit, high resistance Shift solenoid C pressure solenoid failure Transmission to TCM 2/4 Brake pressure solenoid circuit: open circuit, short circuit Transmission internal 2/4 Brake pressure solenoid circuit: open circuit, short circuit TCM Ground circuit: open circuit, high resistance 2/4 Brake pressure solenoid failure Transmission to TCM intermediate speed sensor circuit: open circuit, short circuit, high resistance Transmission internal intermediate speed sensor circuit: open circuit, short circuit, high resistance Transmission to TCM intermediate speed sensor circuit: shielding defective Sensor ground circuit fault Intermediate speed sensor failure Output speed sensor power supply circuit: open circuit, short circuit Transmission to ECM output speed sensor circuits: open circuit, short circuit, high resistance Output speed sensor failure
P0778
TRANS OBD II
P0791
TRANS OBD II
P0791
None
EN16 -026
45
DTC P0831
FAULT DESCRIPTION Clutch cancel switch low voltage (switch normally closed) * Manual transmission input to ECM
MONITORING CONDITIONS Drive vehicle 60 100 km/h (37 62 mph); 1800 2500 rpm; engine load > 0.40 g/rpm
CK ENG 2
OTHER N
CM PIN POSSIBLE CAUSES EN16 -033 Clutch cancel switch supply circuit: open circuit Clutch cancel switch to ECM circuit: open circuit, high resistance Clutch cancel switch failure Clutch cancel switch to ECM circuit: short circuit to high voltage Clutch cancel switch failure
P0832
Clutch cancel switch high voltage (switch normally closed) * Manual transmission input to ECM Clutch pedal safety switch low voltage (switch normally open) * Manual transmission input to ECM
Drive vehicle; shift from 1st to 2nd; stop vehicle Repeat 5 times Drive vehicle; shift from 1st to 2nd; stop vehicle Repeat 5 times
None
EN16 -033
P0834
None
EN16 -031
Clutch pedal safety switch supply circuit: open circuit Clutch pedal safety switch to ECM circuit: open circuit, high resistance Clutch pedal safety switch failure Clutch pedal safety switch to ECM circuit: short circuit to high voltage Clutch pedal safety switch failure
P0835
Clutch pedal safety switch high voltage (switch normally open) * Manual transmission input to ECM J Gate CAN network malfunction
Drive vehicle 60 100 km/h (37 62 mph); 1800 2500 rpm; engine load > 0.40 g/rpm
None
EN16 -031
P0860
Ignition ON 10 seconds
ECM Default: Speed control inhibited Maximum throttle opening for N range inhibited Throttle opening limited to 30% Maximum engine speed reduced
CAN open circuit fault CAN short circuit fault J Gate failure
46
DTC P0915
CK ENG 2
OTHER A
CM PIN POSSIBLE CAUSES JB131 -008 -009 -045 -009 2nd Gear signal to TCM circuit: short circuit, open circuit, high resistance 3rd Gear signal to TCM circuit: short circuit, open circuit, high resistance 4th Gear signal to TCM circuit: short circuit, open circuit, high resistance J-Gate ground circuit: open circuit, high resistance TCM Ground circuit: open circuit, high resistance Refer to page 3
P1000
System (OBD) check not System Readiness Test complete since last memory clear MAF Sensor ground malfunction Ignition ON 10 seconds
None
P1104
ECM Default: Default air mass used Adaptive fuel metering inhibited Catalyst warm up ignition retard inhibited Canister purge inhibited Maximum engine speed reduced ECM Default: Default value of 1.013 BAR (29.92 in hg) used
MAF Sensor to ECM sensor ground circuit open circuit, short circuit to high voltage, high resistance MAF Sensor to ECM sensing circuit: open circuit MAF Sensor failure
P1107
EMS OBD II
Ignition ON 10 seconds
EN16 -127
MAP Sensor to ECM sense circuit: open circuit, short circuit to ground MAP Sensor sensor supply circuit (to splice): open circuit MAP Sensor failure
47
DTC P1108
CK ENG 2
OTHER N
DEFAULT ACTION ECM Default: Default value of 1.013 BAR (29.92 in hg) used
CM PIN POSSIBLE CAUSES EN16 -127 MAP Sensor sensor ground circuit (to splice): open circuit MAP Sensor to ECM sense circuit: short circuit to high voltage MAP Sensor failure Refer to page 3
P1111
System (OBD) checks complete since last memory clear APP Sensor sense circuit low voltage APP1
None
P1122
Battery voltage > 10 v Ignition ON Slowly press accelerator pedal to the floor over a 5 second period. Slowly return the pedal to rest Repeat 3 times Battery voltage > 10 v Ignition ON Slowly press accelerator pedal to the floor over a 5 second period Slowly return the pedal to rest Repeat 3 times
ECM Default: APP angle default value used Speed control inhibited APP adaptions (wear, variance) inhibited
EN16 -103
APP Sensor to ECM sense circuit (APP1): open circuit, high resistance APP Sensor sensor supply circuit: open circuit, high resistance APP Sensor failure
P1123
EMS OBD II
APP Sensor sense circuit high voltage APP1 Note: This DTC could be flagged by both sensor element sensing circuit having faults.
ECM Default: APP angle default value used Speed control inhibited APP adaptions (wear, variance) inhibited
APP Sensor sensor to ECM sense circuit(s) (APP1 or APP2): short circuit to B+ voltage APP Sensor sensor ground circuit(s): open circuit APP Sensor failure
P1146
EMS OBD II
Battery voltage > 12 v Switch OFF all electrical consumers Start engine; idle for 16 minutes with all electrical consumers switched OFF
None
EN16 -053
Generator to ECM CHARGE circuit: open circuit, high resistance Generator regulator failure
48
DTC P1215
MONITORING CONDITIONS Battery voltage > 10 v Ignition ON Slowly press accelerator pedal to the floor over a 5 second period Slowly return the pedal to rest Repeat 3 times Battery voltage > 10 v Ignition ON Slowly press accelerator pedal to the floor over a 5 second period Slowly return the pedal to rest Repeat 3 times Battery voltage > 10 v Ignition ON Slowly press accelerator pedal to the floor over a 5 second period Slowly return the pedal to rest Repeat 3 times
CK ENG 2
OTHER R
DEFAULT ACTION ECM Default: APP angle default value used Speed control inhibited APP adaptions (wear, variance) inhibited
CM PIN POSSIBLE CAUSES EN16 -102 APP Sensor to ECM sense circuit (APP2): open circuit, high resistance APP Sensor sensor supply circuit (to splice): open circuit, high resistance APP Sensor failure
P1216
EMS OBD II
APP Sensor sense circuit high voltage APP2 Note: This DTC could be flagged by both sensor element sensing circuit having faults.
ECM Default: APP angle default value used Speed control inhibited APP adaptions (wear, variance) inhibited
APP Sensor sensor to ECM sense circuit(s) (APP2 or APP1): short circuit to B+ voltage APP Sensor sensor ground circuit(s) (to splice): open circuit APP Sensor failure
P1224
EMS OBD II
ECM Default: Throttle motor and throttle motor relay disabled Throttle valve opening set to default value Idle speed controlled by fuel injection intervention Idle speed adaption inhibited
Throttle adaptions not performed after battery disconnect TP Sensor disconnected TP Sensor to ECM sense circuits: open circuit, high resistance Throttle motor relay failure Throttle motor relay to ECM circuit fault Throttle motor relay power supply open circuit ECM ground circuit fault (relay coil drive) Throttle motor to ECM drive circuits: open circuit, short circuit, high resistance Throttle motor failure Throttle body failure
49
DTC P1229
MONITORING CONDITIONS Battery voltage > 10 v Ignition ON Slowly press accelerator pedal to the floor over a 5 second period Slowly return the pedal to rest Repeat 3 times
CK ENG 2
OTHER R
DEFAULT ACTION ECM Default: Throttle motor and throttle motor relay disabled Throttle valve opening set to default value Idle speed controlled by fuel injection intervention Idle speed adaption inhibited ECM Default: Fuel pump feedback control inhibited ECM Default: Fuel pump feedback control inhibited None
CM PIN POSSIBLE CAUSES Throttle motor disconnected Throttle motor to ECM drive circuits: short circuit or open circuit Throttle motor failure
P1234
EMS OBD II
Start engine Battery voltage > 12 v Idle for 2 minutes Start engine Battery voltage > 12 v Idle for 2 minutes Ignition ON 10 seconds
ECM to fuel pump control module control and / or feedback circuits: open circuit, short circuit, high resistance Fuel pump control module failure ECM to fuel pump control module control and / or feedback circuits: open circuit, short circuit, high resistance Fuel pump control module failure ECM to sensors sensor supply voltage circuit(s): short circuit to ground, short circuit to high voltage, open circuit, high resistance APP Sensor, TP Sensor, IP Sensor, MAP Sensor, FTP Sensor failure(s) ECM to sensors sensor supply voltage circuit(s): short circuit to ground APP Sensor, TP Sensor, IP Sensor, MAP Sensor, FTP Sensor failure(s)
P1236
EMS OBD II
P1240
EMS OBD II
Sensor power supply circuit malfunction (APP Sensor, TP Sensor, IP Sensor, MAP Sensor, FTP Sensor) Sensor power supply circuit low voltage (APP Sensor, TP Sensor, IP Sensor, MAP Sensor, FTP Sensor)
P1241
EMS OBD II
Ignition ON 10 seconds
ECM Default: Throttle motor and throttle motor relay disabled Throttle valve opening set to default value Idle speed controlled by fuel injection intervention Idle speed adaption inhibited
50
DTC P1242
FAULT DESCRIPTION Sensor power supply circuit high voltage (APP Sensor, TP Sensor, IP Sensor, MAP Sensor, FTP Sensor)
CK ENG 2
OTHER R
DEFAULT ACTION ECM Default: Throttle motor and throttle motor relay disabled Throttle valve opening set to default value Idle speed controlled by fuel injection intervention Idle speed adaption inhibited None
CM PIN POSSIBLE CAUSES EN16 -012 -013 ECM to sensors supply voltage circuit(s): open circuit, high resistance, short circuit to high voltage APP Sensor, TP Sensor, IP Sensor, MAP Sensor, FTP Sensor failure(s)
P1243
EMS OBD II
Sensor ground circuits open circuit (APP Sensor, TP Sensor, IP Sensor, MAP Sensor, FTP Sensor) Generator CHARGE circuit high voltage / request low
Ignition ON 10 seconds
ECM to sensors sensor ground circuit(s): open circuit, high resistance APP Sensor, TP Sensor, IP Sensor, MAP Sensor, FTP Sensor failure(s)
P1244
EMS OBD II
Battery voltage > 12 v Switch OFF all electrical consumers Start engine; idle for 16 minutes with all electrical consumers switched OFF Start engine Starter should stop when the key is released from position III (CRANK) Drive vehicle > 32 km/h (20 mph) between 2000 2500 rpm for10 seconds; stop vehicle Repeat 10 times
EN16 -053
Generator to ECM CHARGE circuit: short circuit to high voltage Generator regulator failure Generator failure
P1245
EMS OBD II
None
EN16 -006
P1246
EMS OBD II
None
EN16 -006
Starter relay coil to ECM / ignition switch circuit: short circuit to high voltage Ignition switch failure
51
DTC P1250
MONITORING CONDITIONS Idle engine Switch OFF ignition for 10 seconds Start engine and repeat
CK ENG 2
OTHER R
DEFAULT ACTION ECM Default: Limp home unavailable Vehicle speed limited Speed control inhibited Possible engine shut down ECM Default: Throttle motor and throttle motor relay disabled Throttle valve opening set to default value Idle speed controlled by fuel injection intervention Idle speed adaption inhibited ECM Default: Limp home unavailable Vehicle speed limited Speed control inhibited Possible engine shut down None
CM PIN POSSIBLE CAUSES Throttle return spring failure (throttle body failure)
P1251
EMS OBD II
Engine temperature cool (cooling fans not running) Remove ignition key for 20 seconds (cooling fans not running) Ignition key in, position II for 5 seconds (do not start) Repeat cycle two additional times Idle engine Switch OFF ignition for 10 seconds Start engine and repeat
EN16 -052
Throttle motor relay coil power supply circuit: open circuit (fuse) Throttle motor relay failure Throttle motor relay coil to ECM circuit: open circuit ECM ground circuit fault (relay coil drive)
P1254
EMS OBD II
P1260
EMS JAG
Start engine
Invalid ignition key code Passive anti-theft system (PATS) signal to instrument pack missing or corrupted Security message (PATS) CAN failure NOTE: To clear this DTC, the failure must first be rectified, followed by an ignition ON cycle to allow a successful PATS identification exchange between the ECM and the IC. The fault code can then be cleared.
52
DTC P1313
FAULT DESCRIPTION Misfire rate catalyst damage bank 1 NOTE: This DTC will flag only when accompanied by an individual cylinder misfire DTC: P0300 P0306
CK ENG 2
OTHER A
CM PIN POSSIBLE CAUSES Cylinder compression low Worn camshaft / broken valve spring(s) Fuel delivery pressure (low / high) Fuel injector(s) restricted / leaking Fuel injector(s) continuously open Fuel contamination Fuel injector circuit fault(s) (Injector DTCs also flagged) Spark plug failure / fouled / incorrect gap ECM to ignition coil primary circuit fault (Cylinder misfire detected DTC also flagged) Ignition coil failure Cylinder compression low Worn camshaft / broken valve spring(s) Fuel delivery pressure (low / high) Fuel injector(s) restricted / leaking Fuel injector(s) continuously open Fuel contamination Fuel injector circuit fault(s) (Injector DTCs also flagged) Spark plug failure / fouled / incorrect gap ECM to ignition coil primary circuit fault (Cylinder misfire detected DTC also flagged) Ignition coil failure
P1314
EMS OBD II
Misfire rate catalyst damage bank 2 NOTE: This DTC will flag only when accompanied by an individual cylinder misfire DTC: P0300 P0306
53
DTC P1316
FAULT DESCRIPTION Misfire excess emission NOTE: This DTC will flag only when accompanied by an individual cylinder misfire DTC: P0300 P0306
CK ENG 2
OTHER N
CM PIN POSSIBLE CAUSES Cylinder compression low Worn camshaft / broken valve spring(s) Fuel delivery pressure (low / high) Fuel injector(s) restricted / leaking Fuel injector(s) continuously open Fuel contamination Fuel injector circuit fault(s) (Injector DTCs also flagged) Spark plug failure / fouled / incorrect gap ECM to ignition coil primary circuit fault (Cylinder misfire detected DTC also flagged) Ignition coil failure ECM to fuel pump control module control and / or feedback circuits: open circuit, short circuit, high resistance Fuel pump control module failure CMP Sensor disconnected CMP Sensor gap incorrect / foreign matter on sensor face CMP Sensor sensing circuit: open circuit, short circuit to ground, short circuit to high voltage CMP Sensor 2 failure
P1338
EMS OBD II
Start engine Battery voltage > 12 v Idle for 2 minutes Start engine; momentarily race the engine; stop engine Repeat two additional times Start engine; idle 30 seconds Accelerate from stop through complete engine rpm range; coast to a stop Drive the vehicle steadily between 48 97 km/h (30 60 mph) for 5 minutes; coast to a stop Accelerate smoothly through complete accelerator pedal travel; coast to a stop Idle engine 30 seconds
P1340
EMS OBD II
54
DTC P1341
MONITORING CONDITIONS Start engine; momentarily race the engine; stop engine Repeat two additional times Start engine; idle 30 seconds Accelerate from stop through complete engine rpm range; coast to a stop Drive the vehicle steadily between 48 97 km/h (30 60 mph) for 5 minutes; coast to a stop Accelerate smoothly through complete accelerator pedal travel; coast to a stop Idle engine 30 seconds Battery voltage > 10 v Ignition ON Slowly press accelerator pedal to the floor over a 5 second period Slowly return the pedal to rest Repeat 3 times
CK ENG 2
OTHER N
CM PIN POSSIBLE CAUSES EN16 -068 -069 CMP Sensor disconnected CMP Sensor gap incorrect / foreign matter on sensor face CMP Sensor sensing circuit: open circuit, short circuit to ground, short circuit to high voltage CMP Sensor 2 failure
P1344
EMS OBD II
ECM Default: APP angle default value used Speed control inhibited APP adaptions (wear, variance) inhibited
APP Sensor to ECM sense circuits: short circuit, open circuit, high resistance APP Sensor sensor supply circuits: short circuit, open circuit, high resistance APP Sensor sensor ground circuits: open circuit APP Sensor failure
55
DTC P1367
MONITORING CONDITIONS Start engine Battery voltage > 12 v Idle for 2 minutes
CK ENG 2
OTHER A
DEFAULT ACTION ECM Default: Closed loop fuel metering inhibited Adaptive fuel metering inhibited Catalyst warm up ignition retard inhibited Canister purge inhibited Maximum engine speed reduced Fuel injection cut off (cylinders 1, 3, 5) ECM Default: Closed loop fuel metering inhibited Adaptive fuel metering inhibited Catalyst warm up ignition retard inhibited Canister purge inhibited Maximum engine speed reduced Fuel injection cut off (cylinders 2, 4, 6
CM PIN POSSIBLE CAUSES EN16 -131 Ignition monitoring circuit between splice and ECM: open circuit, short circuit to ground, short circuit to B+ voltage Ignition module / coil bank 1 ground circuit fault
P1368
EMS OBD II
EN16 -132
Ignition monitoring circuit between splice and ECM: open circuit, short circuit to ground, short circuit to B+ voltage Ignition module / coil bank 2 ground circuit fault
56
DTC P1384
MONITORING CONDITIONS Idle engine 30 seconds Accelerate from stop through complete engine rpm range; coast to a stop Drive the vehicle steadily between 48 97 km/h (30 60 mph) for 5 minutes; coast to a stop Accelerate smoothly through complete accelerator pedal travel; coast to a stop Idle engine 30 seconds Idle engine 30 seconds Accelerate from stop through complete engine rpm range; coast to a stop Drive the vehicle steadily between 48 97 km/h (30 60 mph) for 5 minutes; coast to a stop Accelerate smoothly through complete accelerator pedal travel; coast to a stop Idle engine 30 seconds Drive vehicle > 24 km/h (15 mph) between 1500 4000 rpm for30 seconds
CK ENG 2
OTHER N
DEFAULT ACTION ECM Default: Bank 1 VVT hold current set at a constant valve of 450 mA
CM PIN POSSIBLE CAUSES EN16 -109 VVT solenoid valve 1 to ECM PWM drive circuit fault VVT solenoid valve 1 ground circuit fault VVT solenoid 1 failure VVT 1 oil flow fault VVT / camshaft mechanical failure bank 1
P1396
EMS OBD II
ECM Default: Bank 2 VVT hold current set at a constant valve of 450 mA
EN16 -110
VVT solenoid valve 2 to ECM PWM drive circuit fault VVT solenoid valve 2 ground circuit fault VVT solenoid 2 failure VVT 2 oil flow fault VVT / camshaft mechanical failure bank 2
P1516
EMS OBD II
EN16 -031
Gear selector cable setting incorrect Transmission range sensor to ECM circuit: open circuit, high resistance Transmission range sensor failure D 4 Switch to TCM circuit: open circuit, high resistance D 4 Switch failure
57
DTC P1517
MONITORING CONDITIONS Start engine in P Start engine in N Check that engine does not start in R, D, 4, 3, 2 CAUTION: If the P/N switch is faulty, the engine may start while in gear Battery voltage > 12 v Start engine and bring to normal operating temperature > 82 C (180 F) Run engine at 5000 rpm in N for 20 seconds Battery voltage > 12 v Start engine and bring to normal operating temperature > 82 C (180 F) Run engine at 5000 rpm in N for 20 seconds Start engine; idle in P, N Press brake pedal for > 30 seconds; release brake pedal Repeat 5 times Momentarily press brake pedal and release; press again and hold > 30 seconds; release brake pedal Repeat 5 times
CK ENG 2
OTHER A
DEFAULT ACTION ECM Default: Speed control inhibited Maximum throttle opening for N range inhibited Maximum engine speed reduced
CM PIN POSSIBLE CAUSES EN16 -031 Gear selector cable setting incorrect Transmission range sensor to ECM circuit: open circuit or high resistance Transmission range sensor failure
P1532
EMS OBD II
EN16 -039
IMT Valve 2 (top) disconnected IMT Valve 2 (top) to ECM drive circuit fault IMT Valve 2 (top) power supply circuit fault IMT Valve 2 (top) failure
P1549
EMS OBD II
EN16 -038
IMT Valve 1 (bottom) disconnected IMT Valve 1 (bottom) to ECM drive circuit fault IMT Valve 1 (bottom) power supply circuit fault IMT Valve 1 (bottom) failure
P1571
EMS JAG
Brake ON / OFF switch; brake cancel switch malfunction (Brake ON / OFF switch normally open; brake cancel switch normally closed)
Brake ON / OFF switch to ECM circuit: open circuit, short circuit to ground, high resistance Brake ON / OFF power supply circuit: open circuit Brake ON / OFF switch failure Brake cancel switch to ECM circuit: open circuit, short circuit to ground, high resistance Brake cancel switch power supply circuit: open circuit Brake cancel switch failure
58
DTC P1573
CK ENG N
OTHER A
CM PIN POSSIBLE CAUSES JB131 -012 -013 EN16 -010 TP Sensor fault (TP Sensor DTC flagged P0121, P0122, P0123, P0222, P0223) ECM CAN message error If none of the five conditions occur, check: Inertia switch to ECM circuit: short circuit to B+ voltage Inertia switch failure
P1582
1 Inertia switch activated 2 Throttle Limp Home mode 3 Engine starts and stumbles 4 Engine fail to start 5 Engine stall Ignition ON 5 seconds
P1601
TRANS OBD II
P1603
TRANS OBD II
Ignition ON 5 seconds
None
Battery disconnected while the ignition is switched ON B+ power supply circuit: open circuit TCM failure ECM control relay failure ECM control relay to ECM circuit fault ECM control relay coil power supply open circuit ECM ground circuit fault (relay coil drive)
P1606
EMS OBD II
EMS control relay malfunction Note: This DTC could be flagged along with P0032 and P0052, which if flagged, should be corrected first.
Engine temperature cool (cooling fans not running) Remove ignition key for 20 seconds (cooling fans not running) Ignition key in, position II for 5 seconds (do not start) Repeat cycle two additional times
1 2*
None
EN16 -040
59
DTC P1609
CK ENG 2
OTHER R
DEFAULT ACTION ECM Default: Throttle motor and throttle motor relay disabled Throttle valve opening set to default value Idle speed controlled by fuel injection intervention Idle speed adaption inhibited ECM Default: Throttle motor and throttle motor relay disabled Throttle valve opening set to default value Idle speed controlled by fuel injection intervention Idle speed adaption inhibited None
P1611
EMS OBD II
Drive vehicle If fitted, engage speed control Refer to Owners Handbook and ensure that speed control engages normally
ECM Failure
P1629
EMS OBD II
Battery voltage > 12 v Switch OFF all electrical consumers Ignition ON 15 seconds Start engine; momentarily idle with all electrical consumers switched OFF Switch ignition OFF Switch ignition ON
EN16 -065
ECM to generator FIELD return circuit: open circuit, high resistance Generator regulator failure Generator failure
60
DTC P1631
FAULT DESCRIPTION Throttle motor relay coil drive circuit OFF failure
MONITORING CONDITIONS Engine temperature cool (cooling fans not running) Remove ignition key for 20 seconds (cooling fans not running) Ignition key in, position II for 5 seconds (do not start) Repeat cycle twice more Battery voltage > 12 v Switch OFF all electrical consumers Start engine; idle for 16 minutes with all electrical consumers switched OFF If no reoccurrence of DTC(s): hold engine > 1500 rpm for one minute in N Ignition ON 10 seconds
CK ENG 2
OTHER R
DEFAULT ACTION ECM Default: Throttle motor and throttle motor relay disabled Throttle valve opening set to default value Idle speed controlled by fuel injection intervention Idle speed adaption inhibited None
CM PIN POSSIBLE CAUSES EN16 -052 Throttle motor relay coil power supply circuit: open circuit (fuse) Throttle motor relay failure Throttle motor relay coil to ECM drive circuit: open circuit, short circuit to ground
P1632
EMS OBD II
EN16 -079
ECM to generator LOAD feedback circuit: short circuit, open circuit, high resistance Generator regulator failure Generator failure
P1633
EMS OBD II
ECM Default: Throttle motor and throttle motor relay disabled Throttle valve opening set to default value Idle speed controlled by fuel injection intervention Idle speed adaption inhibited ECM Default: Throttle opening limited to 30% Vehicle speed limited Speed control limited
ECM Failure
P1634
EMS OBD II
Idle engine Switch OFF ignition for 10 seconds Start engine and repeat
ECM Failure
61
DTC P1637
CK ENG 2
OTHER A
DEFAULT ACTION ECM Default: Speed control inhibited Maximum throttle opening for N range inhibited Throttle opening limited to 30% Maximum engine speed reduced None
CM PIN POSSIBLE CAUSES EN16 -123 -124 CAN open circuit fault ABS/TCCM (DSCCM) to ECM CAN short circuit fault ABS/TCCM (DSCCM) failure ECM failure
P1638
EMS OBD II
Ignition ON 10 seconds
CAN open circuit fault INST to ECM CAN short circuit fault INST failure ECM failure CAN short circuit fault Control module failure check for additional flagged DTC(s) to locate control module source
P1642
EMS OBD II
Ignition ON 10 seconds
ECM Default: Speed control inhibited Maximum throttle opening for N range inhibited Throttle opening limited to 30% Maximum engine speed reduced ECM Default: Speed control inhibited Maximum throttle opening for N range inhibited Throttle opening limited to 30% Maximum engine speed reduced
P1643
EMS OBD II
Ignition ON 10 seconds
CAN open circuit fault TCM to ECM CAN short circuit fault TCM failure ECM failure
62
DTC P1646
FAULT DESCRIPTION ECM HO2 Sensor control malfunction bank 1 upstream (1/1)
CK ENG 2
OTHER N
CM PIN POSSIBLE CAUSES HO2 Sensor 1/1 heater failure HO2 Sensor 1/1 sensing circuit: short circuit to ground, short circuit to high voltage, open circuit ECM Failure HO2 Sensor 2/1 heater failure HO2 Sensor 2/1 sensing circuit: short circuit to ground, short circuit to high voltage, open circuit ECM Failure ECM Failure
P1647
EMS OBD II
P1648
EMS OBD II
ECM Default: Maximum ignition retard Maximum engine speed reduced ECM Default: Maximum engine speed reduced ECM Default: Throttle opening limited to 30% Vehicle speed limited Speed control inhibited
P1656
EMS OBD II
Ignition ON 10 seconds
EN16 -075
ECM Failure
P1657
EMS OBD II
Engine temperature cool (cooling fans not running) Remove ignition key for 20 seconds (cooling fans not running) Ignition key in, position II for 5 seconds (do not start) Repeat cycle two additional times
EN16 -052
Throttle motor relay failure Throttle motor relay coil to ECM drive circuit: short circuit to B+ voltage
63
DTC P1658
MONITORING CONDITIONS Engine temperature cool (cooling fans not running) Remove ignition key for 20 seconds (cooling fans not running) Ignition key in, position II for 5 seconds (do not start) Repeat cycle two additional times Ignition ON 10 seconds
CK ENG 2
OTHER R
DEFAULT ACTION ECM Default: Throttle opening limited to 30% Vehicle speed limited Speed control inhibited
CM PIN POSSIBLE CAUSES EN16 -052 Throttle motor relay failure Throttle motor relay coil to ECM drive circuit: short circuit to B+ voltage
P1699
EMS OBD II
None
CAN open circuit fault A/CCM to ECM CAN short circuit fault A/CCM failure ECM failure TCM to transmission sensor ground circuit: open circuit TCM ground circuit: open circuit, high resistance Transmission to TCM low clutch timing solenoid circuit: open circuit, short circuit Transmission internal low clutch timing solenoid circuit: open circuit, short circuit TCM ground circuit: open circuit, high resistance Low clutch timing solenoid failure
P1710
TRANS OBD II
Ignition ON 5 seconds
P1745
TRANS OBD II
64
DTC P1746
CK ENG 2
OTHER A
DEFAULT ACTION TCM Default: If short circuit to B+ V: no engine braking in D, 4, 3, 2 If other cause: poor shift quality
CM PIN POSSIBLE CAUSES JB131 -010 -009 Transmission to TCM reduction timing solenoid circuit: open circuit, short circuit to B+ V, short circuit to ground Transmission internal reduction timing solenoid circuit: open circuit, short circuit TCM ground circuit: open circuit, high resistance Reduction timing solenoid failure Transmission to TCM 2/4 brake timing solenoid circuit: open circuit, short circuit Transmission internal 2/4 brake timing solenoid circuit: open circuit, short circuit TCM ground circuit: open circuit, high resistance 2/4 Brake timing solenoid failure ECM CAN message error
P1747
TRANS OBD II
P1777
Comprehensive component monitor transmission drive cycle page 7 Comprehensive component monitor transmission drive cycle page 7
P1780
J Gate incorrect setting Selector cable adjustment / installation incorrect Range sensor incorrect installation / adjustment D 4 Switch to TCM circuit: short circuit, open circuit, high resistance J-Gate ground circuit: open circuit, high resistance TCM Ground circuit: open circuit, high resistance
65
DTC P1793
CK ENG 2
OTHER A
CM PIN POSSIBLE CAUSES JB131 -036 -054 -009 TCM Power supply circuit: open circuit (fuse) TCM Relay failure TCM Relay ground circuit: open circuit, high resistance TCM Relay supply circuits: open circuit (fuse) TCM Ground circuit: open circuit, high resistance CAN open circuit fault CAN short circuit fault TCM failure CAN open circuit fault TCM to ECM CAN short circuit fault ECM failure TCM failure CAN open circuit fault TCM to ABS/TC (DSCCM) CAN short circuit fault ABS/TC (DSCCM) failure TCM failure
P1796
TRANS OBD II
Ignition ON 5 seconds
P1797
TRANS OBD II
Ignition ON 5 seconds
P1799
TRANS OBD II
Ignition ON 5 seconds
None
66