Professional Documents
Culture Documents
SNCP
SNCP
The topic of this article may not meet Wikipedia's general notability guideline. Please help to establish notability by adding reliable, secondary sources about the topic. If notability cannot be established, the article is likely to be merged, redirected, or deleted. (May 2009)
In telecommunications, subnetwork connection protection, or SNCP, is a type of protection mechanism associated with synchronous optical networks such as synchronous digital hierarchy. SNCP is a dedicated (1+1) protection mechanism for SDH network spans which may be deployed in ring, point to point or mesh topologies. It is complementary to Multiplex Section Protection (MSP), applied to physical handover interfaces; which offers 1+1 protection of the handover. An alternative to SNCP is Multiplex Section Shared Protection Rings or MS-SPRings, which offers a shared protection mode. SNCP's functional equivalent in SONET is called UPSR [1] SubNetwork Connection Protection is a per path protection. It follows the principle of Congruent Sending Selective Receive, i.e, Signal is sent on both paths but received only where the Signal Strength is best. When the working path for Signal receiving is cut, the receiver detects SD (Signal Degradation) and the receiver of the other path becomes active. SNCP is a network protection mechanism for SDH networks providing path protection (end-to-end protection). The data signal is transmitted in a ring structure via two different paths and can be implemented in line or ring structures. The changeover criteria are specified individually when configuring a network element. A protection protocol is not required. The switchover to protection path occurs in the non-revertive mode, i.e. if traffic was switched to the protection path due to a transmission fault, there is no automatic switch-back to the original path once the fault is rectified, but only if there is a fault on the new path (the one labeled as protecting and currently services traffic). SNCP is a 1+1 protection scheme (one working and one protection transport entity). Input traffic is broadcast in two routes (one being the normal working route and the second one being the protection route). Assume a failure free state for a path from a node B to a node A. Node B bridges the signal destined to A from other nodes on the ring, both on working and protecting routes. At node A, signals from these two routes are continuously monitored for path layer defects and the better quality signal is selected. Now consider a failure state where fiber between node A and node B is cut. The selector switches traffic on the standby route when the active route between node A and node B is failed. In order to prevent any unnecessary or spurious protection switching in the presence of bit errors on both paths, a switch will typically occur when the quality of the alternate path exceeds that of the
current working path by some threshold (e.g., an order of magnitude better BER). Consecutively, any case of failure drops in SNCPs decision mechanism. Sources: [2] Standards: ITU-T G.841
Group 2
Assignment # 1
MSP vs SNCP
The MSP ring is more complex to handle than the sub network connection protection (SNCP) ring, but it also has more flexible capacity, and the advantages of MSP make it very efficient in terms of the use of network infrastructure. This is especially true if there is a lot of traffic between adjacent nodes on the ring. Unlike an SNCP ring, to perform proper protection switching in the case of failure on an MSSP ring, coordination is required between the add/drop multiplexers (ADMs) so that the switchover to the protection path is harmonious at both ends. The most important advantage of the MSP ring is that bandwidth can be reused on non-overlapping segments of the ring.
Another major advantage of this technology is that low priority traffic can be transported on the unused protection channels, whereas this feature is impossible in the SNCP technology. This lower order traffic is discarded in cases where the protection channel is needed. Sub-Network Connection Protection (SNCP) is a per path protection. Is a mechanism for SDH networks providing path protection (end-to-end protection). The data signal is transmitted in a ring structure via two different paths and can be implemented in line or ring structures. A protection protocol is not required. SNCP is a 1+1 protection scheme (one working and one protection transport entity). Input traffic is broadcasted in two routes (one being the normal working route and the second one being the protection route). The advantage of the SNCP architecture is the simplicity of operation. No extra signaling protocol is needed to perform protection switching in case of failure. The protection switching mechanism is working autonomously in each node, always selecting the signal with the better quality. In the case of a failure, SNCP provides fast switchover, independent of the rest of the network. The main disadvantage of this system is that the bandwidth needed for the protection traffic cannot be used for anything else, and therefore increases the costs of the network infrastructure.
ITU-T Recommendations
All The definitions of protections architecture are defined on the ITU-T recommendation G.841 with the name Types and characteristics of SDH network protection architectures.