Honda BF35

Includes 31ZV360S supplement for the BF45A LHTA
Thank you for purchasing a Honda Outboard Motor. This manual describes the operation and maintenance of the Honda BF35A/45A Outboard Motors. All information in this publication is based on the latest product information available at the time of printing. Honda Motor Co., Ltd. reserves the right to make changesat any time without notice and without incurring any obligation. No part of this publication may be reproduced without written permission. This manual should be considered a permanent part of the Outboard Motor and it must stay with the Outboard Motor if resold.
READ THIS OWNERS MANUAL CAREFULLY. Pay special attention to these symbols and any instructions that follow. B Indicates serious injury or death WILL result if instructions are not followed. B Indicates a strong possibility that serious injury or death may result if instructions are not followed. w Indicates a possibility that minor injury could result if instructions are not followed. [NOTICEI Indicates that equipment or property damage could result if instructions are not followed.
Honda Outboard Motors are designed to give safe and dependable service if operated according to instructions. Operating this Outboard Motor requires special effort on your part to ensure your safety and the safety of others.
-
Careless oneration or misuse may cause iijury or property damage. Read and understand this owners manual before operating the Outboard Motor.
If a problem should arise, or if you have any questions about your Outboard Motor, see an authorized Honda Marine dealer.
HONDA MOTOR CO., LTD. 1990, ALL RIGHTS RESERVED
TYPES OF HONDA BF3A/45A OUTBOARD MOTORS

It may be necessary to refer_tcthis chart for reference purposes when reading this manual Model BF35
BF45
S: Short Shaft
L: Long Shaft
X: Extra Long Shaft
H: Tiller Handle
R: Remote Control
T: Power Trim/Tilt
The gas assisted tilt type motors use a gas damper to assist when manually tilting the motor. The power trim/tilt type motors use an electric/hydraulic power cylinder to trim or tilt the motor.
IDENTIFICATION
STARTER MOTOR -\
NUMBERS
PRODUCT IDENTIFICATION
NUMBER
ENGINE~SERIAL NUMBER
Record the Product Identification Number (RLN.) and the Engine Serial Number for your reference. Refer to the Product Identification Number when ordering parts, and when making technical or warranty inquiries (see page 99).
The Product Identification Number is. stamped on a plate and attached to the right stem bracket. The Engine Serial Number is stamped on the cylinder block under the starter motor which is located in the front of the engine. Product identification number: Engine serial number:
CONTENTS
1. SAFKI-Y
Safety labels .................................................................6 Safety information ...................................................... 7 2. COMPONENT IDENTIFICATION ............................ 8 3. CONTROLS Tiller handle type Engine start button .................................................... 11 Shift lever .................................................................. 11 Choke knob ............................................................... 11 Throttle grip .............................................................. 12 Throttle opening indicator ........................................ 12 Throttle friction knob ................................................ 12 Engine stop switch .................................................... 13 Emergency stop switch lanyard ................................ 13 Oil pressure indicator light ....................................... Overheat indicator light ............................................ :t Remote control type Remote control lever ................................................ 15 Neutral release lever ................................................. 16 Ignition switch .......................................................... 16 Emergency stop switch lanyard ................................ 17 Choke/fast idle lever ................................................. 18 Manual choke knob ................................................... I8 Oil pressure indicator light/buzzer .............................19 Overheat indicator light/buzzer ................................ 19 Remote control & power trim/tilt type Power trim/tilt switch (remote control lever) ........... 20 Power tilt switch (motor pan) ................................... 21 Trim meter ................................................................ 21 Tachometer ............................................................... 21 Manual relief valve ................................................... 22
Gas assisted
tilt type
Tilt lever ....................................................................22 Controls & instruments (common) Tilt lock lever ............................................................ 23 Trim tab ..................................................................... 23 Anode metal .............................................................. 24 Cooling system indicator .......................................... 24 Water intakes ............................................................ 25 Transom angle adjusting rod ..................................... 26 Fuel cap/gauge/vent knob ......................................... 27 Engine over-rev limiter ............................................. 27 4. PRE-OPERATION CHECKS Engine cover removal/installation ............................ 28 Engine oil .................................................................. 29 Fuel level .................................................................. 30 Gasoline containing alcohol ..................................... 3 1 Propeller and cotter pin ............................................. 32 Steering friction adjustment (common) .................... 32 Remote control friction adjustment .......................... 33 Other checks Stem bracket ........................................................... 33 Tool kit ................................................................... 33 Anodes .................................................................... 33 5. STARTING THE ENGINE Fuel line connection .................................................. 34 Starting the engine (Tiller handle type) .................... 36 Starting the engine (Remote control type) ................ 40 Emergencv starting ................................................... 43 Troubcieshooting&rting problems ........................... 48 6. OPERATION Break-in procedure .................................................... 49
l l l
CONTENTS
Tiller handle type Gearshifting ........................................................... 50 Steering .................................................................. 51 Cruising .................................................................. 5 1 Remote control type Gear shifting .......................................................... 52 Cruising ................................................................. 53 Tilting motor Gas assistedtilt type .............................................. 54 Power trim/tilt type ................................................. 57 Power trim/tilt type Trim meter ............................................................. 58 Power tilt switch (motor pan) ................................ 59 Manual relief valve ................................................ Tilt lock lever ........................................................ 2: Trim tab adjustment .................................................. 61 Motor protection system Engine oil pressure and Overheat warning system ...................................... 62 Over-rev limiter .....................................................64 Power trim warning system ................................... Anodes ...................................................................El Shallow water operation ............................................ 66 High altitude operation .............................................. 67 7. STOPPING THE ENGINE Tiller handle type ......................................................68 Remote control type ..................................................70 8. TRANSPORTING ....................................................... 9. CLEANING AND FLUSHING .................................. ;: 10 MAINTENANCE .....................................................74 Tool kit and spare parts ............................................. 74 Maintenance schedule ............................................... 76 Engine oil ..................................................................78 Gear oil .....................................................................80 Spark plugs ............................................................... 82 Battery (not included) ............................................... 83 Lubrication ................................................................85 Engine fuel filter ....................................................... 86 Fuel tank and filter ....................................................88 Fuse replacement ......................................................89 Propeller ....................................................................90 Submerged motor ......................................................9 1 11. STORAGE .................................................................93 12. TROUBLESHOOTING ............................................95 13. SPECIFICATIONS ...................................................97 14. WARRANTY SERVICE ...........................................99 15. WIRING DIAGRAM .............................................. 100 16. INDEX .....................................................................103
1. SAFETY
SAFETY LABELS
These labels are in the locations shown. They warn you of potentia1 hazards that could seriously injure you. Read these labels carefully.
Frn~4.~~~~~MI-~ICan~INLWunr~
FLAMMABLE EXTREMELY DANGER
I. SAFETY
SAFETY INFORMATION For your safety and the safety of others, pay special attention to these precautions. Operator Responsibility Know how to stop the engine quickly in case of emergency. Understand the use of all controls. Do not exceed the boat manufacturers power recommendation, and be sure that the outboard motor is properly mounted. Never permit anyone to operate the outboard motor without proper instruction. Stop the engine immediately if any one falls overboard. Do not run the motor while the boat is near anyone in the water. Attach the emergency stop switch lanyard securely to the operator.
l l l
Before operating the outboard motor, familiarize yourself with all laws and regulations relating to boating and the use of outboard motors. Do not attempt to modify the outboard motor. Always wear PERSONAL FLOTATION DEVICE (PFD) when on board. Do not remove any guards, labels, shields, covers or safety devices; they are installed for your safety.
Refuel carefully to avoid spilling fuel. Avoid overfilling the fuel tank (there should be no fuel in the filler neck). After refueling, tighten the filler cap securely. If any fuel is spilled, make sure the area is dry before starting the engine.
Fire and Burn Hazards Gasoline is extremely flammable, and gasoline vapor can explode. Use extreme care when handling gasoline.
l
Remove the fuel tank from the boat for refueling. Refuel in a well-ventilated area with the engine stopped. Keep flames and sparks away, and do not smoke in the area.
2. COMPONENT
THROTTLE GRIP
IDENTIFICATION
(TILLER
HANDLE TYPE)
LEVER
on, PReS\SURE INDICATOR LIGHT
HANDLE
THdT 1 LOCK STERN BRACKET
ldiir-7
w v I 0 &l l/l I Y...-.-..YL PROPEL1 XR --
COOLING
=r
c WATER INTAKE
OVERHEAT INDICATOR LIGHT ENGINE STOP .l-..CH
THROTTLE _____- ~~~ FRICTION KNOB
Mi
ACCESS COVER ANTI-VENTILATION D, ATE-
ENGINE START
M
\ CHOKE KNOB EMERGENCY / STOP SWITCH CLIP \ EMERGENCY STOP SWITCH LANYARD I SPARE EMERGENCY STOP SWITCH CLIP
RIM TAB .u
WASH PLUG (Flush plug) I GEAR OIL DRAIN PLUG
2. COMPONENT
ENGINE COVER FUEL LINE CONNECTOR \ POWER TILT SWI;rCH
IDENTIFICATION
(REMOTE
CONTROL
TYPE)
OIL FILLER CAP CHOKE KNOB I POWER TRIM/TILT SWITCH \ NEUTRAL RELEASE LEVER
\
STEERING I I
OIL PRESSURE INDICATOR
COOLING TRANSOM ANGLE INDICATOR
/e-r
In! - STERN BRACKET /
CHOKE/FAST IDLE LEVER
ENGINE OIL MANUA< RELIEF VALVE GEAR OIL / LEVEL PLUG GEAR DRAIN PLUG \ ACCESS COVER
/ SPARE EMERGENCY
ETAL) HAUST PORT \ PROPELLER
hAIN
~BNTHATION __ .-.rwn. .,m
WA
EMERGENCY STOP SWITCH LANYARD EMERGENCY STOP SWITCH CLIP
/
r
-/ EMERGENCY ENGINE STOP SWITCH
2. COMPONENT
IDENTIFICATION
POWER TRIM/TILT
VENT KNOB FUEL GAUGE /
TYPES
FUEL CAP TACHOMETER
PRIMER BULB
FiJEL HOSE CONNECTOR (FEMALE)
TRIM METER
10
3. CONTROLS
Engine Start Button R
(reverse)
(TILLER
HANDLE
TYPE)
Shift Lever
N (reverse)
R N
Choke Knob
EN&NE START BUTTON
SHIti
LEVER
CHOKk KNOB
Move the gearshift lever to the N (neutral) position before starting. The engine will not start unless the gearshift lever is in the N (neutral) position.
There are three gearshift lever positions. F (forward): The boat moves forward. N (neutral): The transmission gears are disengaged from the engine. R (reverse): The boat reverses.
When the engine is cold, pull the choke knob. A rich fuel mixture is provided to the engine by pulling the choke knob.
11
3. CONTROLS (TILLER
Throttle Grip
HANDLE TYPE)
Throttle opening indicator
THROTTLE OIPENING INDICATOR
Throttle Friction Knob
THROTTLE
GRIP RELEASE
Turn the grip clockwise or counterclockwise to adjust the engine speed. Turning the grip in the direction shown by the arrow increases engine speed.
The curve on the grip indicates throttle opening.
Use the throttle friction knob to set the throttle grip at a certain position while cruising. Turning the friction knob clockwise sets the throttle grip, and it is released by turning the friction knob counterclockwise.
12
3. CONTROLS
Engine Stop Switch Emergency Stop Switch Lanyard
(TILLER
HANDLE
TYPE)
ENGINE STOP SWITCH \
EMERGENCY ENGINE STOP StiTCH
STOP SWITCH CLIP EMERGENCY STOP SWITCH LANYARD
Push the engine stop switch to stop the engine.
The emergency stop switch lanyard is provided to stop the engine immediately in the event the operator should fall overboard or away from the controls. The emergency stop switch clip must be engaged with the engine stop switch or the engine will not start. When the emergency stop switch clip becomes disengaged with the engine stop switch the engine will stop immediately.
Attach the emergency stop switch lanyard securely to the operator when operating the outboard motor.
13
3. CONTROLS (TILLER
SPARE EMERGENCY ,STOP SWITCH CLIP
HANDLE TYPE)
Oil Pressure Indicator Light I I\ Overheat Indicator Light
OIL PRESSURE INDICATOR LIGHT
OVERHEAT INDICATOR
LIGHT
A spare emergency stop switch clip is provided near the engine stop switch.
The green oil pressure indicator light is normally ON when the outboard motor is running. When the engine oil level is low or the engine lubrication system is faulty, the green oil pressure indicator light turns OFF and the engine speeddecreases gradually.
When the engine cooling system is faulty, the red overheat indicator light turns ON and the engine speed decreasesgradually.
14
3. CONTROLS
Remote Control Lever
(REMOTE
CONTROL
TYPE)
The remote control lever controls gear selection and throttle opening positions. It is necessaryto pull up the neutral release lever to operate the remote control lever.
REMOTE CONTROL LEVER
F (forward): Moving the lever to the F position (approximately 30 from the N position) will engagethe forward gear. Moving the lever further from the F position will increase the throttle opening and the boat forward speed. N (neutral): The engine idles and the transmission gears are disengaged.
R (reverse): Moving the lever to the R position (approximately 30 from the N position) will engage the reverse gear. Moving the lever further from. the R position will increase the throttle opening and the boat reverse speed.
15
3. CONTROLS (REMOTE CONTROL TYPE)

Neutral Release Lever Ignition Switch ON To run the engine after starting (the battery will discharge if the key is left in this position with the engine not running). OFF To stop the engine (IGNITION OFF).
The neutral release lever is on the remote control lever to prevent an accidental gear engagement. The remote control lever will not engage forward or reverse gear unless the neutral release lever is pulled up.
The remote control box is equipped with a key type ignition switch. Key positions: START To activate the startermotor and start the engine. (the remote control lever must be in the neutral position)
16
3. CONTROLS
Emergency Stop Switch Lanyard
(REMOTE
CONTROL
TYPE)
SWITCH LANYARD
SPAkE EMERGENCY STOP SWITCH CLIP
The emergency stop switch lanyard is provided to stop the engine immediately in the event the operator should fall overboard or away from the controls. The emergency stop switch clip must be engagedwith the emergency engine stop switch or the engine will not start. When the emergency stop switch clip becomesdisengaged from the emergency engine stop switch the engine will stop immediately.
The emergency engine stop switch should not be used to normally stop the engine. Use the ignition switch to normally stop the engine. Attach the emergency stop switch lanyard securely to the operator when operating the outboard motor.
A spare emergency stop switch clip is provided on the remote control box.
17
3. CONTROLS (REMOTE CCDNTROL TYPE)

Choke/Fast Idle Lever
n CHOKE XIMUM FAST IDLE
Manual Choke Knob
OWEST POSITION
CHOKE tiOB
The choke/fast idle lever provides two functions: 1. Electric choke solenoid activation for easy engine start up. 2. Engine fast idle. The choke/fast idle lever will not move unless the remote control lever is in the N (neutral) position. Conversely, the remote control lever will not move unless the choke/fast idle lever is in the lowest position.
Lift and hold the choke/fast idle lever up fully, this will provide a rich fuel mixture and the correct fast idle. Gradually lower the choke/fast idle lever to the lowest position to decrease the choke and fast idle.
A manual choke knob is provided on the right side of the motor which can be usedin the event the battery is discharged. Pull the manual choke knob, and a rich fuel mixture will be provided to the engine.
18
3. CONTROLS
03 Pressure Indicator Light/Buzzer
(REMOTE
CONTROL
TYPE)
Overheat Indicator Light/Buzzer
The green oil pressure indicator light turns OFF and the buzzer sounds when the oil level is low and/or the engine lubrication system is faulty. The engine speed slows down gradually*
The red overheat indicator light turns ON and the buzzer sounds when the engine cooling system is faulty. The engine speed slows down gradually.
19
3. CONTROLS (REMOTE.CONTRBL
Power Ikim/Tilt Switch (remote
& POWER TRIM/TILT

XRTA
TYPE)
type outboard
control lever) Power Ikim

Press the power him/tilt switch on the remote control lever to adjust the
Power Trim Do not trim this engine when you are
using a large amount of throttle

opening. If you do try lo trim the engine, under certain conditions, propeller thrust may override the power trim hydraulics and cause the engine to return to the transom angle adjusting rod. (Full in position) Power Tilt Press the power tilt switch on the remote control lever to adjust the motor tilt angle of 20 to 60. By using the power tilt switch the operator can change the tilt angle of the motor for shallow water operation, beaching, launching from a trailer, or mooring.
motor trim angle of 0 to 20 to maintain proper boat trim. The power

him/tilt switch located on the remote control lever can be operated while the boat is under way or while stopped. By using the power trim/tilt switch the
TRIM/TILT SWITCH
!I
operator can change the trim angle of the motor to achieve maximum boat acceleration, speed, stability and maintain optimum fuel consumption. Power Tilt Pressthe power trim/tilt switch on the remote control lever to adjust the motor tilt angle of 20 to 60. By using the power trim/tilt switch the operator can change the tilt angle of the motor for shallow water operation, beaching, launching from a trailer, or mooring.
picziq
Excessive trim/tilt angle during operaUion can cause the propeller to raise out of the water and cause propeller ventilation and engine over-revving. Excessive trim/tilt angle can also damage the water pump.
20
3. CONTROLS
Power Tilt Switch (motor pan)
(REMOTE
CONTROL
& POWER TRIM/TILT

Tachometer
TYPE)
Trim Meter
TRIM METER POWER TILT SWITCH
TACHOMETER
The power tilt switch located on the motor pan is a conveyance switch for tilting the motor for trailering, or preforming outboard maintenance. This power tilt switch should only be operated with the boat being stopped and motor off.
The trim meter has a range of 0 to 20 and indicates the trim angle of the outboard motor. Refer to the trim meter when using the power trim/tilt switch to achieve proper boat performance.
The tachometer shows the approximate engine speedin revolutions per minute. Refer to the tachometer when using the power trim/tilt switch to achieve proper boat and motor performance.
21
3. CONTROLS (REMOTE CONTROL & POWER TRIM/TILT

Manual Relief Valve If the power trim/tilt switch will not tilt the outboard motor, the motor can be manually tilted up or down by opening the manual relief valve. To tilt the outboard motor manually, turn the manual valve under the left stem bracket no more than 1 or 2 turns counterclockwise using a screw driver. After tilting the motor, turn the manual relief valve clockwise securely. The manual relief valve must be tightened securely before operating the motor or the motor could tilt up when operating in reverse.
LEFT STERN BRACKET
TYPE)
Tilt Lever (GAS ASSISTED TYPE)
MANUAL POWER m rel=1
MANUAL-RELIEF
VALVE
Do not turn this screw. If this screw is turned hydraulic oil will bleed out of the power trim/tilt system. Should this happen it will be necessary to consult your authorized Honda Marine dealer and have the system refilled.
Moving the tilt lever to the FREE position allows the motor to be tilted and moving the tilt lever to the LOCK position locks the motor in the desired position. Use the tilt lever to temporarily tilt the motor when the boat is operating in shallow water, or mooring in shallow water. The tilt lever must be in the LOCK position before operating the motor or the motor could tilt up when operating in reverse.
22
3. CONTROLS
Tilt Lock Lever Trim Tab
& INSTRUMENTS
(common)
PROPELLER Use the tilt lock lever to hold the motor in the highest tilt position when the boat is moored for a long time. Tilt the motor up as far as it will go then move the tilt lock lever into the lock position and gently lower the motor. When making a turn, if an unequal amount of effort is required to turn the steering wheel or tiller handle right or left, adjust the trim tab so that an equal amount of effort is required.
Distribute the load evenly in the boat and run the boat in straight course at full throttle. Slightly turn the steering wheel or tiller handle for both right and left turns to determine if an equal amount of effort is required. If adjustment is necessary loosen the tightening bolt and turn the trim tab right or left. Make small adjustments at a time and retest. Incorrect trim tab adjustment can cause adverse steering. The trim tab also functions as an anode.
23
3. CONTROLS & INSTRUMENTS

Anode Metal
(common)
Cooling System Indicator \
+I
ANODi (stem bracket)
COOiING
SYSTEM INDICATOR
The anodes are made from a sacrificial material which helps to protect the outboard motor from corrosion.
1 NoTlCq Painting or coating the anodes will lead to rust and corrosion damage to the outboard motor.
The cooling system is monitored here to make sure cooling water is circulating through the engine.
24
3. CONTROLS
Water Intakes
& INSTRUMENTS
(ctimmon)
WATiR
INTAKES
The engine cooling water is drawn into the water pump through these water intakes.
25
3. CONTROLS & INSTRUMENTS

Transom Angle Adjusting Rod
TO CHANGE
(common)
TRANSOM
ANGLE ADJUSTING ROD UNLOCKED POSITION I 1 . ----/ J
TRANSOM ANGLE ADJUSTING ROD
+=I TO LOCK
LOCKED POSITION
The transom angle adjusting rod is used to adjust the motor angle to achieve the correct boat him. There are 5 adjustment holes located in the stem bracket. Push in and turn the transom angle adjusting rod up to remove. To install insert into the proper hole and turn down to lock. After installation pull the transom angle adjusting rod outward to be sure it is locked in place. Start with the transom angle adjusting rod in the hole closest to the boat tran-
som, lower the motor and operate the boat at full speed.If the bow is excessively low stop the boat. Tilt the motor up and raise the transom angle adjusting rod one more hole away from the transom and retest. The optimum boat trim is when the boat is parallel with the water.. The transom angle adjusting rod stops the motors forward movement. The motor should never be operated with the transom angle adjusting rod removed.
26
3. CONTROLS
Fuel Cap/Gauge/Vent Knob
VENT KNOB I
& INSTRUMENTS
(common)
Before transporting or storing the fuel tank turn the vent knob fully clockwise to the closed position. B Gasoline is extremely flammable, and gasoline vapor can explode, causing serious injury or death. Do not smoke or allow flames or sparks in your working area. KEEP OUT OF REACH OF CHILDREN.
Over-Rev Limiter This outboard motor is equipped with an engine over-rev limiter which limits the maximum engine r-pm. This overrev limiter protects the engine from mechanical damage. The over-rev limiter may be activated by putting the propeller in a light load condition or propeller ventilation. When the over-rev limiter is activated the engine rpm will become unstable or erratic. Should this occur reduce the throttle opening and wait for the engine rpm to stabilize then increase the throttle opening.
On the power trim/tilt type motors lower the trim angle on high speed turns to reduce the possibility of propeller ventilation.
GAUGE
FUEL FILLER CAP
The fuel gauge is part of the fuel cap. The fuel cap vent knob controls air entering and leaving the fuel tank. When refilling the fuel tank, turn the vent knob counterclockwise to the open position and remove the fuel cap. Before transporting, storing or refilling the fuel tank inspect the condition of the fuel cap gasket and replace if necessary.
27
4. PRE-OPERATION
Engine Cover Removal/Installation
(FRONT)
CHECKS
(REAR)
ENGINE COVER
To remove, release the front and rear engine cover latches and remove the engine cover. To install, position the engine cover over the engine and hook and lpck the front and rear latches.
28
4. PRE-OPERATION
Engine Oil Engine oil is a major factor affecting engine performance and service life. w Running the engine with insufficient oil can cause serious engine damage. Recommended oil Use high-detergent, premium quality Cstroke engine oil, certified to meet or exceed U.S. automobile manufactures requirements for American Petroleum Institute (API) Service Classification SG, SF/CC, CD. Engine oils classified SG, SF/CC, CD will show these designations on the container. Select the appropriate viscosity for the average temperature in your area. SAE 1OW30 is recommended for general, all-temperature use.
TEMP ;
-3 -20 -10 20 0 40 10 60 20 30 40%
CHECKS
SAf
Inspection 1. Position the outboard motor vertically, and remove the engine cover. 2. Remove the oil level dipstick and wipe with a clean rag. 3. Reinsert the dipstick all the way in, then pull it out and read the level. If the oil registers near or below the lower level mark, remove the oil filler cap and fill to the upper level mark with the recommended oil. m Do not overfill. Excessive oil can damage the engine.
4. Reinstall the oil filler cap and tighten securely. 5. Install the engine cover and lock It securely. When the engine oil is contaminatedor discolored, replace with fresh engine oil (refer to page 78 for oil capacity, replacementinterval and procedure).
29
4. PRE-OPERATION
CHECKS
VENTKNOB
FUEL CAP
Check the fuel gauge and refill the tank to the SAFE FILL level mark if necessary. Fuel tank capacity : 6.6 US gal. (25 lit)
B Gasoline is extremely flammable, and gasoline vapor can explode, causing serious injury or death. Do not smoke or allow flames or sparks in your working area. KEEP OUT OF REACH OF CHILDREN.
Refilling Remove the fuel tank from the boat for refilling. Turn the vent knob counterclockwise to the open position and remove the fuel cap. Refuel in a well-ventilated area. Fill the fuel tank up to the SAFE FILL level mark only. Inspect the condition of the fuel cap gasket and replace if necessary. After refilling, install and tighten the fuel cap securely. Turn the vent knob clockwise to the closed position. Return the fuel tank to the boat.
30
4. PRE-OPERATION
Recommended fuel Your engine is designed to use any gasoline that has a pump octane number ( v) of 86 or higher, or that has a research octane number of 91 or higher. Gasoline pumps at service station normally display the pump octane number. We recommend that you use unleaded fuel becauseit produces fewer engine and spark plug deposits and extends the life of exhaust system components. Never use stale or contaminated gasoline or an oil/gasoline mixture. Avoid getting dirt, dust or water in the fuel tank. Use of a lower octane gasoline can cause persistent pinging or heavy spark knock (a metallic rapping noise) which, if severe, can lead to engine damage. @!!@ If spark knock or pinging occurs at a steady engine speed under normal load, change brands of gasoline. If spark knock or pinging persists, consult your authorized Honda dealer. Failure to do.so is considered misuse, and damage caused by misuse is not covered by Hondas Limited Warranty. Occasionally you may experience light spark knock while operating under heavy loads. This is no cause for concern, it simply means your engine is operating efficiently. GASOLINES CONTAINING ALCOHOL If you decide to use a gasoline containing alcohol (gasohol), be sure its octane rating is at least as high as that recommended by Honda. There are two types of gasohol: one containing ethanol, and the other containing methanol. Do not use gasohol that contains more than 10% ethanol. Do not use gasoline containing methanol (methyl or wood alcohol) that does not also contain cosolvents and corrosion inhibitors for methanol. Never use
CHECKS
gasoline containing more than-5% methanol, even if it has cosolvents and corrosion inhibitors. Fuel systemdamageor engine performance problems resulting from the use of fuels that contain alcohol is not covered under the warranty. Honda cannot endorse the use of fuels containing methanol since evidence of their suitability is as yet incomplete. Before buying fuel from an unfamiliar station, try to find out if the fuel contains alcohol. If it does, confirm the type and percentage of alcohol used. If you notice any undesirableoperating symptoms while using a gasoline that contains alcohol, or one that you think contains alcohol, switch to a gasoline that you know does not contain alcohol.
31
4. PRE-OPERATION
Propeller and Cotter pin
CHECKS
Steering Friction Adjustment (common) II DECREASE r0
--------G-Jpz~~
COTTi3.a PIN
(stainless steel) Propeller Check the propeller blades for damage, wear or deformation and replace if necessary.Never operate the outboard motor with a damaged propeller. Carrying a spare propeller, propeller nuts, and cotter pins are common practice. If the propeller is damaged and no spare propeller is available consult an authorized Honda Marine dealer. (Refer to page 90 for propeller change information)
PROPELLER
Operate the steering wheel or tiller handle right and left and check for the amount of drag felt. Adjust the steering friction adjuster so that a slight amount of drag is felt. The steering should move smoothly and freely.
Cotter Pin Check the cotter pin for damage and correct installation. If the cotter pin needs replacement use only a new genuine Honda stainless steel cotter pin.
32
4. PRE-OPERATION
Remote Control Friction Adjustment Other Checks
10 x 17. mnt WRENCH (I mm WRENCH r J 9 FLAT SCREWDRIVER PHILLIPS sCREWDRIVER C=TT c_s OIL CHECK SCREWDRIVER c STARTER
CHECKS
G
ROPE
TO INCREASE
PLIERS 13
SCREWDRIVER HANDLE Bg+J 18 x 19 mm WRENCH
TO DECREASE FRICTION
Operate the remote control lever into forward and reverse gears and check for the amount of drag felt. Adjust the remote control friction adjuster so that a slight amount of drag is felt. The remote control lever should move smoothly and freely.
Check the following items: 1. The fuel hose for kinking, collapsing or loose connections. 2. The stem bracket for damage and mounting bolts for proper torque. 3. The tool kit contents. Compare your tool kit contents against the tool kit illustration above. Replace any missing items. 4. The anodes for damage,looseness or excessive corrosion. The anodes help to protect the outboard motor from corrosion any time they are exposed directly to the water.
Replace the anodes when they have been visibly reduced in size. m Painting or coating the anodes will lead to rust and corrosion damage to the outboard motor. The following materials should be kept with the boat: 1. Owners Manual. 2. Tool Kit. 3. Spare engine oil, spark plugs, propeller and propeller cotter pins. 4. Required information regarding boating laws and regulations.
33
5. STARTING THE ENGINE

Fuel Line Connection
FUEL HOSE CONNECTOR
w If the outboard end fuel hose connector is forcibly installed in the reversed direction, the fuel hose connector O-ring seal can be damaged. A damaged O-ring seal can cause a fuel leak.
(FUEL TANK END) \
(OUTBOARD END)
The fuel tank must be properly secured in the boat. This will protect the fuel tank from mechanical damage caused by the fuel tank shifting. The fuel tank must be in a well ventilated area to reduce the chance of a gasoline vapor explosion. Avoid direct sunlight on the fuel tank. Due to the fuel pump capacity, do not place the fuel tank more than 6 feet away from the motor or lower than 3 feet below the outboard end fuel hose connector.
Inspect the condition of the fuel cap gasket, fuel hose, and the O-ring seals in the fuel hose connectors. Replace the fuel cap gasket, hose, or fuel connectors if they are cracked, damaged or leak fuel. Be sure the fuel hose is not kinked. 1. Connect the fuel hose connectors to the fuel tank and the outboard motor. Install the outboard end fuel hose connector with the clip toward the outside. Be sure the fuel hose connectors are securely snapped in place.
34
5: STARTING
VENT KNOB OUTLET END
THE ENGINE
2. Turn the fuel cap vent knob at least 2 or 3 turns counterclockwise, to open the fuel tank vent.
3. Hold the primer bulb so that the outlet end is higher than the inlet end. The arrow on the primer bulb points upward. Squeezethe primer bulb several times until it feels firm, indicating that fuel has reached the carburetors. Check for fuel leaks and repair any leaks before starting the motor. Do not squeezethe primer bulb when the motor is running becausethis could cause the carburetors to overflow.
35
5. STARTING THE ENGINE (TILLER

\
ENGINE STOP SWITCH
HANDLE TYPE)
SPARE EMERGENCY STOP SWITCH CLIP-
f;;;$;;;;psTop
EilERGtiCY STOP SWITCH LANYARD
GEAR SHIIh LEVER
1NOTICE/ The propeller must be lowered into the water. Running the outboard motor out of the water will damage the water pump and overheat the engine. 1. Engage the emergency stop switch clip located at one end of the emergency stop switch lanyard with the engine stop switch. Attach the other end of the emergency stop switch lanyard securely to the operator.
2. Move the gearshift lever to the N (neutral) position. The engine will not start unlessthe gearshift lever is in the N (neutral) position.
m lf the operator does not attach the emergency stop switch lanyard, and is thrown from his seat or out of the boat, the out-of-control boat can seriously injure the operator, passengers, or bystanders. Always properly attach the lanyard before starting the motor.
36
5. STARTING
THE ENGINE
(TILLER
HANDLE
TYPE)
THROTIiE
GRIP
3. Align the engine start symbol QI on the throttle grip with the pointer F on the tiller handle.
4. When the engine is cold or ambient temperature is low pull the choke knob. 5. Pressthe start button and start the engine. The starter motor consumesa large amount of current. Do not run it continuously for more than 5 secondsat a time. If the engine does not start within 5 seconds,wait at least 10 secondsbefore using the starter motor again.
/iGTiiq
Do not press the start button while the engine is running. This can damage the starter motor and flywheel.
37
5. STARTING THE ENGINE (TILLER HANDLE TYPE)
CHOltE K\NOB
THROITLE
GRIP
WATER INTAG (each side)
6. If it was necessaryto use the choke knob to start the engine, slowly return it to its initial position. Turn the throttle grip in the SLOW direction to a position where the engine does not stall.
7. After the engine starts, verify water is flowing through the cooling system by monitoring the cooling system indicator. The amount of water coming out of the cooling system indicator will vary due to thermostat operation. Stop the engine if water does not come out of the cooling system indicator or if you see steam. Check the water intake screens and the cooling system indicator discharge port and if necessary remove any obstructions. If the problem continues, contact your closest authorized Honda Marine dealer. INoTicE] R unning the outboard motor with an obstruction in the coolingsystem can damage the water pump and overheat the engine.
38
5. STARTING
OIL PRESSURE ~IyIcATORLIyHT
THE ENGINE
(TILLER
HANDLE
TYPE)
\ Bjfl
&, NORMAL: ABNORMAL:
GREEN LIGHT ON GREEN LIGHT BLINKING OR OFF
9. Warm up the engine as follows: Above 41F (5C) - run the engine for 2 or 3 minutes. Below 41F (YC) - run the engine for at least 5 minutes at approximately 2,000 rpm. Failure to completely warm up the engine will result in poor engine performance.
8. With the engine running, check to seeif the green engine oil pressure indicator light turns ON. Stop the engine if the oil pressure indicator light does not mm ON. Check the engine oil level (see page 29). If the oil level is normal and the oil pressure indicator light does not turn ON, contact your closest authorized Honda Marine dealer.
39
5. STARTING THE ENGINE (REMQTE CONTROL TYPE)

EMERGENCY N (neutralj
EhERGENCY SiOP SWITCH CLIP
I NOTICEI The propeller must be lowered into the water. Running the outboard motor out of the water will damage the waterpump and overheat the engine.
1. Engage the emergency stop switch clip located at one end of the emergency stop switch lanyard with the emergency engine stop switch. Attach the other end of the emergency stop switch lanyard securely to the operator.
If the operator does not attach the emergency stop switch lanyard, and is thrown from his seaQ or out of the boat, the out-of-control boat can seriously injure the operator, passengers, or bystanders. Always properly attach the lanyard before starting the motor.
The engine will not start unless the emergency stop switch clip is engaged with the emergency engine stop switch.
A spare emergency stop switch clip is provided on the remote control box.
2. Move the control lever to the N

(neutral) position.
The engine will not start unless the control lever is in the N (neutral) position.
40
5. STARTING
THE ENGINE (REMOTE

ON
CONTROL
TYPE)
XIMUM FAST
3. When the engine is cold or the ambient temperature is low, lift and hold the choke/fast idle lever up fully. This will provide a rich fuel mixture and the correct fast idle. When the engine is warm, raise the free acceleration lever to the MAXIMUM FAST IDLE position and hold it in the position.
The choke/fast idle lever will not move unless the control lever is in the N (neutral) position.
4. Holding the choke/fast idle lever in position, turn the ignition key to the START position and release the key when the engine starts. The starter motor consumes a large amount of current. Do not run it continuously for more than 5 secondsat a time. If the engine does not start within 5 secondswait at least 10 seconds before using the starter motor again. m Do not turn the ignition key to the start position while the
engine is running. This can damage the starter motor and flywheel. 5. After starting the engine, return the lever slowly to the position where the engine does not stall and hold the lever in the position.
The control lever will not move unless the choke/fast idle lever is returned to the lowest position.
41
5. STARTING THE ENGINE (REMOTE CONTROL TYPE)

COOLING SYSTEM INDICATOR e OIL PRESSURE INDICATOR LIGHT
WATER INTAKE (each side)
NORMAL : GREEN LIGHT ON BNORMAL : GREEN LIGHT BLINKING
6. After the engine starts, verify water is flowing through the cooling system by monitoring the cooling system indicator. The amount of water coming out of the cooling sys-, tern indicator will vary due to thermostat operation. Stop the engine if water does not come out of the cooling system indicator or if you see steam. Check the water intake screens and the cooling system indicator discharge port and if necessary remove any obstructions. If the problem continues, contact your closest authorized Honda Marine dealer. m Running the outboard motor with an obstruction in the cooling system can damage the water pump and overheat the engine.
7. With the engine running, check to see if the green engine oil pressure indicator light turns ON. Stop the engine if the oil pressure indicator light does not turn ON. Check the engine oil level (see page 29). If the oil level is normal and the oil pressure indicator light does not turn ON, contact your closest authorized Honda Marine dealer. 8. Warm up the engine as follows: Above 41F (5C) - run the engine for 2 or 3 minutes. Below 41F (YC) - run the engine for at least 5 minutes at approximately 2,000 rpm. Failure to completely warm up the engine will result in poor engine performance.
42
5. STARTING
Emergency Starting
(FRONT) (REAR)
THE ENGINE
FIXINCLEVER
If the electric starting system will not start the engine the engine can be started by using the pull starter rope from the tool kit. 1. Releasethe front and rear engine cover latches then remove the engine cover.
2. Remove the four 6 x 25 mm bolts and the three washersthen remove the flywheel cover. Do not lose the washers.
43

ENGINE STOP SWITCH
EMERGENCY STOP SWITCH
SHIF? LEVER (TILLER HANDLE TYPE) (REMOTE CONTROL TYPE) SPARE EMERGEN STOP SWITCH CLIP
3. Depending on what type of outboard motor you have, move the shift lever or the control lever to the N (neutral) position.
4. If your outboard motor is a tiller handle type, engage the emergency stop switch clip, located at one end of the emergency stop switch lanyard, with theengine stop switch.
44
EMERGENCY sTOPswITCH CLIP'
SPARE~MEKGENCY STOPSWITCHCLIP
/ CHOkEIiNOB (TILLERHANDLETYPE)
5. If your outboard motor is a remote control type, turn the ignition key to the ON position. Engage the emergency stop switch clip, located*at one end of the emergency stop switch .lanyard, with the emergency engine stop switch.
A spareemergencystop switch clip is provided on the remotecontrol box.
6. If the engine is cold or the ambient temperature is low, pull the manual choke knob located on the front of the outboard motor.
45

ENGINE START,SYMBOL
n
GRIP
CHOKFJFAST
POIN-TER
I THROTTLE
{REMOTE CONTROL TYPE)
(TILLER HANDLE TYPE)
(REMOTE CONTROL TYPE)
If the fuel system is working properly, it should only be necessary to pull the engine 1 or 2 times with the choke knob out.
7. On the tiller handle type align the engine start symbol QI on the throttle grip with the puinter ) on the tiller handle. On the remote control type lift the choke/fast idle lever. The choke/fast idle lever will stay up in the fast idle position.
46
5. STARTING
FLYWHEEL EMERGENCY
THE ENGINE
lO.If it was necessaryto use the manual choke knob to start the engine, slowly return it to its initial position. 11.Slowly return the throttle grip to the SLOW position or the choke/fast idle lever to the lowest position to where the engine does not stall. parts can caussinjury. Use extreme care when installing the engine cover. Do not operate the outboard motor without the engine cover. 12.Leave the flywheel cover off and reinstall the engine cover. Lock the engine cover latches. Attach the emergency stop switch lanyard securely to the operator and return to the closest boat landing. Contact your closest authorized Honda Marine dealer and have the outboard motor and the electrical system checked.
8. Set the emergency starter rope knot in the notch in the flywheel and wind the emergency starter rope counterclockwise around the flywheel.
9. Pull the emergency starter rope lightly until resistance is felt, then pull briskly. If the engine fails to start refer Troubleshooting page95.
47

Ikoubleshooting
SYMPTOM Startermotor doesntturn over.
Starting Problems
POSSIBLE CAUSE 1. Shift lever not in neutral position. 2. Blown fuse. 3. Weak battery. REMEDY 1. !jet shift lever in neutral position. 2. Replacefuse. (refer to page 89) 3. Start by using starter rope (refer to page43).
1. Emergencystop switch clip is not engaged. Startermotor turns over but engine will not
Start.
1. Engagethe emergency stop switch clip (refer to page 13 and 17) 2. Supply fuel. (refer to page 30) 3. Open vent knob. (refer to page 35) 4. Squeeze primer bulb to supply fuel. (refer to page35) 5. Clean and dry sparkplug. (refer to page82)
2. Out of fuel 3. Vent knob not open. 4. Primer bulb has not been squeezed. 5. Engine flooded.
6. OPERATION
Break-in Procedure Break-in period 10 hours Break-in operation allows the moving parts to wear-in evenly and thus ensuresproper performance and longer outboard motor life. Break-in your new outboard motor as follows: First 15 minutes: Run the outboard motor at trolling speed. Use the minimum amount of throttle opening necessaryto operate the boat at a safe trolling speed. Next 45 minutes: Run the outboard motor up to a maximum of 2,000 to 3,000 rpm or 10% to 30% throttle opening. Next 60 minutes: Run the outboard motor up to maximum of 4,000 to 5,000 rpm or 50% to 80% throttle opening. Short bursts of full throttle are acceptable but do not operate the motor continuously at full throttle. Next 8 hours: Avoid continuous full throttle operation (100% throttle opening). Do not run the outboard motor at full throttle for more than 5 minutes at a time. For boatsthat plane easily, bring the boat up on plane then reducethe throttle opening to the specified break-in settingscalled out above.
49
6. OPERATION
(TILLER
HANI9LE TYPE)
N (neutral) 63 R (reverse)
POINj-ER
FAST INhICATOR
Gearshift lever has 3 positions: FORWARD, NEUTRAL, and REVERSE. An indicator at the base of the gearshift lever aligns with the letters F, N, and R on the motor pan. 1. Align the pointer on the tiller handle with the SLOW position on the throttle grip to decreaseengine speed.
The throttle mechanism is designed to limit the throttle grip travel when operating in the REVERSE or NEUTRAL positions. The throttle grip can only be turned to the FAST position when operating in forward gear.
2. Put the tilt lever in the LOCK position to prevent the outboard motor from tilting up, when operating in reverse (refer to page 22).
3. Move the gearshift lever to engage
the desired gear.
50
6. OPERATION
Steering
RIGHT TURN LEFT TURN
(TILLER
HANDLE
TYPE)
Cruising
Move the tiller handle to the left.
Move the tiller handle to the right.
THROTkLE
GRIP
RELEASE
The tiller handle is moved in the opposite direction in which you want the boat to turn.
With the gearshift lever in the F (forward) position, turn the throttle grip toward the FAST mark to increase speed. For optimum fuel economy, limit throttle opening to 2/3.
To set the throttle at a steady speed, turn the throttle friction knob clockwise. To release the throttle grip for manual speed control, turn the friction knob counterclockwise.
51
6. OPERATION
Gear Shifting
(REMOTE CONTROL TYPE)

N
(neutral) I 30
R (reverse)
While pulling up the neutral release lever, move the control lever 30 toward F (forward) or 30 toward R (reverse) to engage the desired gear.
1,I
PULL UP
Moving the control lever further from 30 will increase throttle opening and boat speed.
The control lever will not move unless the neutral releaselever is pulled up and choke/fast idle lever is in the lowest position.
52
6. OPERATION
Cruising
POWER TRIM/TILT SWITCH
(REMOTE
CONTROL
N (neutral)
TYPE)
1. On the Power trim/tilt type, press the DN portion of the power trim/tilt switch and tilt the motor to the lowest position.
2. Move the control lever from N (neutral) 30 toward F (forward) to engage the F (forward) gear. Moving the control lever further from 30 will increase the throttle opening and boat speed. 3. For optimum fuel economy, limit throttle opening to 2/3.
53
6. OPERATION
Tilt Lever
(GAS ASSISTED TILT TYPE)
\\i\d
SWITCH
ENGINE COVER GRIP
PUSH
TILT LEVER
Tilt the motor up to prevent the propeller and gear case from hitting the bottom when beaching or stopping in shallow water. 1. Move the gearshift lever to the N ( neutral) position and stop the engine.
2. To tilt the motor up, move the tilt lever to the FREE position, then pull the engine cover grip and raise the motor.
54
6. OPERATION
(GAS ASSISTED
TILT TYPE)
3. With the outboard motor tilted up to the desired position, move the tilt lever to the LOCK position to lock the motor.
4. To lower the motor back down, move the tilt lever to the FREE position, while holding the engine cover grip, then lower the motor gently. Move the tilt lever to LOCK position. The tilt lever must be in the LOCK position before operating the motor or the motor could tilt up when operating in reverse.
55
6. OPERATION
(GAS ASSISTED SYSTEM)

TILTLOCK
3. Move the tilt lever to the LOCK position. 4. To lower the motor, move the tilt lever to the FREE position. Lift up on the engine cover grip and swing the tilt lock lever to the free position. 5. Lower the engine gently. Move the lever to the LOCK position.
Use the tilt lock lever to hold the motor in the highest tilt position when the boat is moored for a long time. 1. Move the tilt lever to the FREE position (refer to page 55), then pull the engine cover grip and tilt the motor all the way up. 2. Move the tilt lock lever to the LOCK position and lower the outboard motor slowly.
56
6. OPERATION
XRTA type outboard (refer to page 20)
POWER TRIM/TILT SWITCH
(POWER TRIM/TILT
TYPE)
The power trim/tilt system can adjust the motor angle while cruising, or the motor tilt angle while mooring. Motor trim angle adjustment is necessaryto compensatefor boat load or weight distribution, water conditions, propeller or engine condition. The motor trim angle can be adjusted while accelerating or cruising to obtain the maximum boat speed,optimum boat stability, and fuel economy. Under normal conditions, the boat will achieve optimum boat performance when the motor is running at maximum rpm and the ventilation plate is level with the water.
Press UP to raise bow. Press DN to lower bow. I 20 0 TRIM ANGLE 60 ANGLE CONTROL LEVER
Presseither the UP or DN portion of the power trim/tilt switch and trim the motor to the best position for the cruising conditions. The power trim/tilt system operates when the switch is pressed,andit stops when the switch is released.
I&!@@ Excessive trim/tilt angle during operation can cause the propeller to raise out of the water and cause propeller ventilation and engine over-rewing. Excessive trim/tilt angle can also damage the water pump and overheat the engine. To trim motor up slightly, press the UP portion momentarily. To trim motor down slightly, press the DN portion momentarily.
Decrease the trim angle on high speed turns to reduce the possibility of propeller ventilation.
Improper motor him angle can result in an unstable steering condition. The power trim/tilt warning system will be activated and an intermittent buzzer sounds when the motor is trimmed excessively (refer to page 64).
57
6. OPERATION
MOTOR TRIMMED TOO LOW
(POWER TRIM/TILT
TYPE)
MOTOR TRIMMED
TOO HIGH
Trim Meter The trim meter indicates the trim angle of the motor. Refer to the trim meter, and press the UP or DN portion of the power trim/tilt switch to adjust,the motor trim angle to achieve boat performance and stability. BOW TOO HIGH DUE TO BOWTOOLOW DUETO I. LOAD IN THE REAR I. LOAD IN THE FRONT 2. MOTORTRIMMED TOOHIGH 2. MOTORTRIMMEDTOOLOW
ROUGH WkVi?s
MOTOR TRIMMED CORRECTLY
When cruising:
(A) Into a high wind, trim the motor down slightly to level the bow and improve boat stability. (B) With a tail wind, trim the motor up slightly to raise the bow and
With the motor trimmed low the trim meter will read as shown. To raise the bow increase the motor trim angle by pressing the Up portion of the power trim/tilt switch.
With the motor trimmed high the trim meter will read as shown. To lower the bow decreasethe motor trim angle by pressing the DN portion of the power trim/tilt switch.
improve boat stability. (C) Through rough waves, do not trim the motor too low or too high to avoid an unstable steering condition.
58
6. OPERATION
Power Tilt Switch (Motor Pan) Manual Relief Valve
LE
(POWER TRIM/TILT
TYPE)
POWER TILT SWITCH
The power tilt switch located on the motor pan is a convenience switch for tilting the motor for trailering, or performing outboard motor maintenance. This power tilt switch should only be operated when the boat is stopped and the motor is off.
Do not turn this screw. If this screw is turned hydraulic oil will bleed out of the power trim/tilt system. Should this happen it will be necessaryto contact your closest authorized Honda Marine dealer and have the system refilled.
If the power trim/tilt switch will not tilt the outboard motor, the motor can be manually tilted up or down by operating the manual relief valve. To tilt the outboard motor manually, turn the manual relief valve under the left stem bracket no more than lsor 2 turns counterclockwise using a screw driver. After tilting the motor, turn the manual relief valve clockwise securely. The manual relief valve must be tightened securely before operating the motor or the motor could tilt up when operating in reverse.
59
6. OPERATION
(POWER TRIM/TILT
TYPE)
It may be necessary to lift the engine cover grip slightly to swing the tilt lock lever into the LOCK position.
3. To lower the motor, tilt the motor up slightly, move the tilt lock lever to the FREE position, and lower the motor to the desired position.
LEVER
Tilt Lock Lever Use the tilt lock lever when the boat is moored. 1. Tilt the motor up as far as it will go using the power trim/tilt switch. 2. Move the tihlock lever to the LOCK position and lower the outboard motor until the lock lever contacts the stem bracket (refer to page 23).
60
6. OPERATION
Trim Tab Adjustment
RIGHT
TIGHTENING
The trim tab is provided to adjust for torque steer which is a reaction of the propeller rotation or propeller torque. If during a high speedturn an unequal amount of effort is required to turn the boat right or left, adjust the trim tab so that an equal amount of effort is required. Distribute the load evenly in the boat and run the boat in a straight course at full throttle. Slightly turn the steering wheel or tiller handle for both right and left turns to determine the amount of effort required.
If less effort is required to make left tums: Loosen the trim tab tightening bolt and turn the rear end of the trim tab toward the left. Tighten the bolt securely. If less effort is required to make right tums: Loosen the trim tab tightening bolt and turn the rear end of the trim tab toward the right. Tighten the bolt securely.
Make small adjustments at a time and retest. Incorrect trim tab adjustment can cause adverse steering. The trim tab also functions. as a sacrificial anode.
INoTICE] Painting or coating the anode will lead to rust and corrosion damage to the outboard motor
61
6. OPERATION
(MOTOR PROTECTIONSYSTEM)
Engine Oil Pressure and Overheat Warning System If the engine oil pressure drops and/or the engine overheats, either or both warning systems could be activated. When activated the engine speed will decreasegradually and the green oil pressure indicator light will turn OFF andthe red overheat indicator light will turn ON. A continuous buzzer will sound on the remote control type. The engine speed can not be increased (TILLER HANDLE TYPE) with a larger throttle opening until the malfunction is corrected. When the malfunction is corrected the engine speed will increase gradually.
INDICATOR LIGHTS (REMOTE CONTROL TYPE)
Buzzer Remote control type
I Normal
Abnormal Low oil pressure Overheat Low oil pressure/ overheat
ON OFF ON OFF
1 OFF OFF ON ON
Continuous Continuous Continuous
62
6. OPERATION
When the oil pressure warning systems is activated: 1. Stop the engine immediately and check the engine oil level (refer to page 29). 2.If the oil is up to the recommended level, restart the engine. If the oil pressure warning system stops after 30 seconds,the system is normal. If the throttle was closed suddenly after
cruising at full throttle, the engine speed may drop below the specified idle speed. This could cause the oil pressure warning system to activate momentarily.
(MOTOR
PROTECTION
SYSTEM)
If the motor is turned off after running at full throttle, the engine temperature may rise above normal. If the motor is restarted, shortly after being turned off, the overheat warning system could be activated momentarily.
COOLING SYSTEM INDICATOR
When the overheat warning system is activated: 1. Return the gearshift lever or control lever to the N (neutral) position 1immediately. Check to seeif water is flowing out of the cooling system indicator. 2. If water is flowing out of the cooling system indicator, continue idling for 30 seconds.If the overheat warning system stops after 30 secondsthe system is normal.
3. If the overheat warning system stays activated, stop the engilie. tilt up the motor and check the water intakes for obstructions. If there are no obstructions at the water intakes, return to the closest boat landing and contact your closest authorized Honda Marine dealer.
3. If the oil pressure warning system stays activated after 30 seconds, return to the closest boat landing and contact your closest authorized Honda Marine dealer.
63
6. OPERATION
(MOTOR PROTECTION
Power llim
SYSTEM)
Over-Rev Limiter This outboard motor is equipped with an engine over-rev limiter which activates when the engine speed increases excessively. The over-rev limiter can be activated while cruising, tilting up the motor, or when ventilation occurs during a sharp turn. When tire over-rev limiter is activated: 1.Reduce the throttle opening immediately and check the trim angle. 23 the trim angle is correct but the over-rev limiter stays activated, stop the engine and check the condition of the outboard motor and check the propeller for damage. Correct or service as necessary,.
Warning System
If the motor trim angle is more than 20 and the control lever is moved more than 40 forward/rearward from the N (neutral} position, an intermittent buzzer will sound and beep at one second intervals.
64
6. OPERATION
Anodes
(MOTOR
PROTECTION
SYSTEM)
When the power trim warning system is activated: 1. Immediately decreasethe trim angle by pressing the DN portion of the power trim/tilt switch. 2. Immediately reduce the throttle opening to SLOW and operate the engine at low speed.
The anodes are a sacrificial material which helps to protect the outboard motor from corrosion.
INoTICE] Painting or coating the anodes will lead to rust and corrosion damage to the outboard motor.
There are also 2 small sacrificial anodes in the water passages the engine of block.
65
6. OPERATION
Shallow Water Operation [NOTICE1Excessive trim/tilt angle during operation can cause the propeller to raise out of the water and cause propeller ventilation and engine over-revving. Excessive trim/tilt angle can also damage the water pump and overheat the engine. When operating in shallow water, tilt the motor up to prevent the propeller and gear case from hitting the bottom (refer to pages 54 and 57). With the motor tilted up, operate the motor at low speed. Monitor the cooling system indicator for water discharge. Be sure that the motor is not tilted so high that the water intakes are out of the water. If an excessive amount of throttle is used when operating in forward gear, the motor will return to the transom angle adjusting rod. (Gas assisted tilt type). If the motor trim angle is more than 20 and the control lever is moved more than 40 forward/rearward from the N (neutral) position, the power trim warning system will be activated
(refer to page 6.4). (Power trim/tilt type).
66
6. OPERATION
High Altitude Operation At high altitude, the standard carburetor air-fuel mixture will be excessively rich. Performance will decrease,and fuel consumption will increase. High altitude performance can be improved by installing a smaller diameter main fuel jet in the carburetor and readjusting the pilot screw. If you always operate the outboard motor at altitudes higher than 6,000 feet above sea level, have your authorized Honda Marine dealer perform these carburetor modifications. Even with suitable carburetor jetting, engine horsepower will decrease approximately 3.5% for each 1,000 foot increase in altitude. The effect of altitude on horsepower will be greater than this if no carburetor modification is made.
w Operation of the outboard motor at an altitude lower than the carburetor is jetted for may result in reduced performance, overheating, and serious engine damage caused by an excessively lean air/fuel mixture.
67
7. STOPPING THE ENGINE (TILLER

Emergency Engine Stop
ENGINE STOP SWITCH
HANDLE TYPE)
Normal Engine Stop

GEA,RSHIFF LEVER N
EMERGENCY STOP SWITCH LANYARD I
SWITCH CLIP
Disengage the emergency stop switch clip from the engine stop switch by pulling the emergency stop switch lanyard. It is a good idea to stop the engine with the emergency stop switch lanyard from time to time to be sure that the switch is operating properly.
1. Turn the throttle grip to SLOW position and move the gearshift lever to N(neutral).
68
7. STOPPING
THE ENGINE
(TILLER
HANDLE
TYPE)
ENGINE STOP SWITCH
2. Push the engine stop switch until the engine stops.
69
7. STOPPING THE ENGINE (REMOTE CONTROL TYPE)

Emergency
,nnuI.~.
Engine
Stop
Normal Engine Stop

N (neutral)
OP SWITCH
ERGENCY STOP ITCH LANYARD
IGNITION EMERGENCY STOP SWITCH CLIP
KE
Disengage the emergency stop switch clip from the emergency engine stop switch by pulling the emergency stop switch lanyard. It is a good idea to stop the engine with the emergencystop switch lanyard from time to time to be sure that the switch is operating properly.
1. Move the control lever to the N (neutral) position and turn the ignition key to the OFF position.
2. When the boat is not in use, remove and store the ignition key.
70
8. TRANSPORTING
Tkailering
STEERING FRICTION Horizontal transport or storage: Rest the motor on the case protectors
CASE PROTEbTORS
When trailering or transporting the boat with the motor attached, it is recommended that the motor remain in the normal run position. Tighten the steering friction adjuster securely to stop the motors side to side movement.
If there is insufficient road clearance with the motor in the normal run position, then trailer the motor in the tilted position using a motor support bar (refer to your motor support bar manufacturers instructions) or remove the motor from the boat.
When you place the outboard motor horizontally to transport, be sure to protect it from impact and damage.
71
9. CLEANING
AND FLUSHING
FLUSH KIT COUPLER 5. Move the gearshift lever or control
lever to the N (neutral) position. Blush the outboard motor in the neutral position only. 6. Turn on the fresh water supply to the flush kit coupler. m Running the outboard motor without sufficient cooling water will damage the water pump and overheat the engine.
WASH PLUG (flush plug)
Thoroughly clean and flush the outboard motor with fresh water after operating in dirty or salty water. Flush Kit (optional part) 1. Wash the outside of the outboard motor with clean, fresh water. 2. Remove the wash plug and sealing washer from the WASH plug hole in the gear case. Be sure not to remove the oil level plug from the OIL LEVEL plug hole in the gear case.
B KeeD children and pets away from ihe area, and stay clear of all moving parts during this procedure. 3. Remove the sealing washer from the wash plug and install the sealing washer on the flush kit coupler. 4. Install the flush kit coupler into the WASH plug hole and connect a fresh water hose to the flush kit coupler.
72
9. CLEANING
AND FLUSHING
8. Allow the engine to run at idle for at least 5 minutes to clean the inside of the motor. 9. Stop the motor and remove the flush kit coupler. lO.Remove the sealing washer from the flush kit coupler and install the sealing washer on the wash plug.
If tape was usedto cover the three water intakes in step7, remove the tape now.
CdOLINi; SYSTEM INDICATOR
7. Start the engine. Monitor the cooling system indicator. Stop the engine if water does not come out of the cooling system indicator and check the fresh water supply. If the fresh water supply is insufficient it may be necessaryto temporarily cover the three water intakes with duct tape.
11Jnstall the wash plug into the gear case securely.
73
10. MAINTENANCE
Periodic maintenance and adjustment are important to keep the motor in the best operating condition. Service and inspect according to the MAINTENANCE SCHEDULE. Stop the engine before performing any maintenance. If it is necessaryto run the engine make sure the area is well ventilated. Never run the engine in an enclosed or confined area. Exhaust contains poisonous carbon monoxide gas; exposure can cause loss of consciousness and may lead to death. (NOTICEI Running the outboard motor without sufficient cooling water will damage the water pump and overheat the engine. To maintain the cooling system efficiency, flush the outboard motor with fresh water after operating in salt water or dirty water. Make sure there is at least 2 inches of water above the ventilation plate. Or follow the flushing procedure(refer to pages72 and 73).
74
10. MAINTENANCE
Tool Kit and Spare Parts The following tools and spare parts are supplied with the outboard motor for maintenance, adjustment, and emergency repairs. TOOL KIT
10 x 12 mm WRENCH > 8 mm WRENCH STARTER ROPE
FLAT SCREWDRIVER
PLIERS
PHILLIPS
SCREWDRIVER
3
TOOL BAG
SCREWDRIVER HANDLE OIL CHECK SCREWDRIVER
18 x 19 mm SOCKET WRENCH
75
10. MAINTENANCE
MAINTENANCE SCHEDULE Use only genuine HONDA parts or their equivalent for maintenance or repair. Replacement parts which are not of equivalent quality may damage the motor.
10. MAINTENANCE
, \
REGULAR SERVICE PERIOD (3) Perform at every indicated month or op,eratinghour 1 intervals, whichever comes first. Clean (Replace if necessary) Check Change Thermostat Fuel line Battery fluid Bolts and Nuts Check Check (Replace if necessary) Check-refilling (if necessary) Check-tightness 0 Cable connection Check-tightness
EACH USE
FIRST 20 HRS OR MONTH
EVERY 100 HRS OR 6MONTHS EVERY 200 HRS OR YEAR
EVERY 400 HRS OR 2 YEARS
ITEM Fuel tank and filter filter Fuel filter
0 0 0
O(2)
0
O(2)
NOTE: (1) Lubricate more frequently when used in salt water. (2) These items should be serviced by an authorized Honda Marine dealer, unless the owner has the proper tools and is mechanically proficient. Seethe Honda Shop Manual. (3) For professional commercial use, log hours of operation to determine proper maintenance intervals.
77
10. MAINTENANCE
Engine Oil Engine oil is a major factor affecting engine performance and service life. Oil check interval: OIL CAPACITY: 2.1 US qt (2.0 lit)...When oil filter is not replaced 2.5 US qt (2.4 lit)....When oil filter is replaced Recommended oil: SAElOW-30 engine oil or equivalent, API Service classification SG, SF/CC, CD.
Each use.
Oil change interval:
After the first 20 hours, then every 200 hours. (Refer to the maintenance schedule page 76).
Engine Oil Replacement Drain the oil while the engine is still warm to assurerapid and complete draining. 1. Position the outboard motor vertically, and remove the engine cover. Remove the oil filler cap.
78
10. MAINTENANCE
DRAINPLUG
2. Loosen the drain plug cover screw using a flat blade screwdriver and remove the drain plug cover.
3. Placethe drain plug cover as shown to use it as an oil drain guide. Place a suitable container under the guide.
4. Remove the engine oil drain bolt and washer using a 12 mm wrench and drain the engine oil. 5. Install a new sealing washer on the drain bolt and tighten the bolt secure1 y. 6. Reinstall the drain plug cover.
79
I
10. MAINTENANCE
8. Reinstall the oil filler cap. Always wash your handsafter handling usedoil. Also, pleasedisposeof usedmotor oil in a manner that is compatible with the environment. We suggestyou take it in a sealedcontainer to your local service station reclamation center. Do not throw it in the trash, pour it on the ground, down a drain, or into the water. 7. Refill to the-upper level mark on the oil level dipstick with the recommended oil. NOTE: To avoid incorrect gauging of the engine oil level, inspect the oil level when the engine hascooled.. Gear Oil Oil check interval: Every 100 hours. Oil change interval: After the first 20 hours, then every 100 hours. (Refer to the maintenance schedule page 81 ). OIL CAPACITY: 0.53 US qt. (0.5 lit) Recommended oil: Outboard motor ME 90 hypoid gear oil API Service Classification (GL-4 or GL-5).
80
10. MAINTENANCE
LEVEL PLUG \
Gear Oil Change 1. Position the outboard motor vertically. 2. Remove the level plug and drain plug to drain the oil. Inject oil through the drain plug hole until it starts flowing out through the level plug hole. Use new sealing washers and reinstall the level plug first and then the drain plug securely.
GEAR OIL BOTTLE
DRAIN
Gear Oil Level/Check 1. Position the outboard motor vertically. 2. Remove the level plug and seeif oil
flows out. If no oil flows out, fill through the drain plug hole until the oil starts to flow out through the level plug hole. If there is water in the oil, the water will flow out first when the drain plug is removed, or the oil will be milky colored. If the oil appears abnormal contact your closest authorized Honda Marine dealer.
A gear oil bottle is recommended to fill the gear case. The end of the drain plug is a magnet. Remove all metal particles from the end of the drain plug before reinstalling. Do not reinstall the drain plug in the level plug hole.
OIL CAPACITY: 0.53 US qt. (0.5 lit)
3. Use new sealing washers and reinstall the level plug and drain plug securely.
81
10. MAINTENANCE
Spark Plugs
To ensure proper engine operation, the spark plugs must be properly gapped and free of deposits.
Check-replace interval:
0.0244028 in (0.6-0.7mm)
After the first 20 hours, then every

200 hours. (Refer to the maintenance schedule page 76).
Recommended spark plug:
DR7EA (NGK), X22ESR-U (NIPPON DENSO) Use only the recommended spark plugs or equivalent.
ISpark plugs which have an improper heat range may cause engine damage.
PLUG CAPS
.. v
1. Allow the engine to cool. The spark

plugs will be hot if the engine has been running. 2. Remove the engine cover.
3. Disconnect the spark plug caps from the spark plugs. 4. Use the wrench and screwdriver supplied in the tool kit to remove the spark plugs. 5. Check the spark plugs. Replace the spark plugs .if there is apparent wear, or if the insulators are cracked or chipped. Clean the spark plugs with a wire brush if they are to be reused.
6. Measure the plug gaps with a feeler gauge. The gaps should be 0.024-0.028 in - _ (0.6-0.7 mm). Correct as necessary by carefully bending the side electrode.
82
10. MAINTENANCE
1-1 The spark plugs must be securely tightened. A loose spark plug can become very hot and may cause engine damage. Overtightening the spark plugs can damage the threads. Battery (not included) Minimum requirements
12V-70AH marine cranking battery.

Maintenance interval Refer to the maintenanceschedule page77 and your battery manufacturers instructions for servicing or recharging information.
Check the battery cablesto be sure

7. Thread the plugs in by hand to prevent cross threading. they are securely connected to the battery terminals. Tighten if necessary. If the battery terminals are corroded or if recharging is necessary,remove the battery from the boat to clean or recharge.
8. After the spark plugs are seated,

tighten with a spark plug wrench to compress the washers. If installing new sparkplugs, tighten l/2 turn after the sparkplugs seatto compressthe washers.If reinstalling used spark plugs, tighten l/8 l/4 turn after the spark plugs seatto compressthe washers.
83
10. MAINTENANCE
NEGATIVE (-)
CARRYING
Battery
cleaning
B Batteries produce exDlosive hydrogen gas. A spark or ilame can explode the battery causing serious Injury or blindness. Provide adequate ventilation. Keep sparks and flames away. Follow the procedure below carefully.
POSITIVE (+) BATTERY CABLE (red)
tains
corrosive
sulfuric
&id.
Contact with eyes or skin causes burns. Wear protective clothing and use eye protection when working near the battery. POISON - KEEP OUT OF REACH OF CHILDREN
EMERGENCY PROCEDURES: Eyes Flush with water from a cup or other container for at least 15 minutes. Call a physician immediately. Skin Remove contaminated clothing. Flush skin with large quantities of water. Call a physician. If swallowed Drink water or milk and call your local poison control center or physician immediately.
Removal: 1. Disconnect the negative ( - > battery cable first, then disconnect the positive (+) battery cable. 2. Removethe battery from the boat. Clean the battery terminals with a
wire brush or sand paper. Clean the
battery with a solution of baking soda

and warm water, taking care not to get the solution of water in the battery cells. Dry the battery thoroughly.
3. Clean the battery cable ends with a wire brush or sand paper.
84
10. MAINTENANCE
Installation: 1. Return the battery to the boat. Install the battery in the correct size corrosion-resistant battery box. 2. Connect the positive (+) battery cable first, then connect the negative (-) battery cable. Tighten the cable nuts securely. 3. Coat the battery terminals and cable ends with marine grease. 4. Secure the corrosion-resistant battery box properly in the boat. To keep potential sparks away from the fuel tank, do not secure the battery near the fuel tank. Lubrication Lubrication interval: After the first 20 hours, then every 100 hours.
(Refer to the maintenance schedule page 76.1
Apply marine anticorrosion greaseto the following parts:

,- THROTTLE REEL ~1
1 r PROPELLER SHAFT -
85
10. MAINTENANCE
Engine Fuel Filter
ARBURETOR
B Gasoline is extremely flammable, and gasoline vapor an explode, causing serious injury or death. Do not smoke or allow flames or sparks in your working area. KEEP OUT OF REACH OF CHILDREN. Always work in a well-ventilated area. Make sure that any fuel drained from the outboard motor is stored in an approved gasoline container. Be careful not to @ill any fuel when replacing the filter. Spilled fuel or fuel vapor may ignite. If any fuel spilled, make sure the area is dry before starting the engine.
CONNECTOR FUEL HOSE
,\
FUEL FILTER
CHOKE KNOB
The engine fuel filter is located under the engine cover between the fuel coupling and the fuel pump. Water or sediment accumulated in the fuel filter can cause loss of power or hard starting. Check interval: Every 100 hours (Refer to the maintenance schedule page 77). Change interval: Every 400 hours (Refer to the maintenance schedule page 77).
Check 1. Disconnect the fuel hose connector from the outboard motor. 2. Pull the choke knob fully and remove the engine cover.
86
10. MAINTENANCE
FUEL FILTER
ARROW (Fuel Flow Direction)
3. Pull the spring retainer toward you, and raise the fuel filter. 4. Check the fud filter for water accumulation or sediment. If no water or sediment are found, reinstall the fuel filter properly.
Change 1. Remove the fuel filter. Before removing the fuel filter, to prevent fuel leakage,place fuel hose clamps on the fuel hosesat each side of the fuel filter.
2. Install the new fuel filter so the arrow on the fuel filter points toward the fuel pump. Fuel flow will be reducedif the fuel filter is installed backward. 3. Connect the fuel hoses to the fuel filter securely with the hose clips. Remove the fuel hose clamps used to close the fuel hoses.
87
10. MAINTENANCE
Fuel Tank and Filter 4. Securely connect the fuel hose connector to the outboard motor page 34. 5. Prime the engine using the primer bulb page 35. Check for fuel leaks. &pair any fuel leaks if necessary.
If loss of power or hard starting are found to be caused by excessive water or sediment accumulation in the fuel filter, inspect the fuel tank. Clean the fuel tank and tank filter if necessary. It may be necessaryto drain the fuel tank completely and refill with fresh gasoline.
Fuel Tank Cleaning

1. Disconnect the fuel hose from the
fuel tank. extremely flammable, and gasoline vapor can explode, causing serious injury or death. Do not smoke or allow flames or sparks in your working area. KEEP OUT OF REACH OF CHILDREN. Cleaning interval: Every 200 hours (Refer to the maintenance schedule page 77). Inspect the condition of the fuel cap gasket, fuel hose, and the O-ring seals
in the fuel hose connectors. Replace the fuel cap gasket, hose, or fuel con2. Empty the gasoline from the fuel
tank into an approved gasoline container. Pour in a small quantity of fresh gasoline, and clean the tank thoroughly. Drain and dispose of the gasoline properly.
nectors if they are cracked, damaged or leak fuel. Be sure the fuel hose is not kinked.
10. MAINTENANCE
Fuse Replacement
FUEL TANK HOSE CONNECTOR FUSE COVER
FUEL TANK FILTER
BLOWN FUSE
Fuel Tank Filter Cleaning/Replacement 1. Turn the fuel tank hose connector counterclockwise to remove the fuel tank filter. 2. Clean the fuel tank filter with nonflammable cleaner or solvent. Replace the fuel tank filter if necessary. 3. After cleaning or replacement, reinstall the fuel tank filter and fuel tank hose connector securely.
If the fuse is blown, running the engine
will not chargethe battery and the electric starter will not work. RUSE RATING: 15A Never use a fuse with a different rating from that specified. If the fuse is blown, check the cause, then replace the fuse with a spare fuse of the samerated capacity. Unless the cause is found, the fuse may blow again.
Replacement 1. Stop the engine. 2. Remove the engine cover. 3. Pull the blown fuse out of the clip. 4. Rush a new 15A fuse into the clip. A spare 15A fuse is located in the fuse holder. If the sparefuse is not available, the motor will needto be startedwith the pull starterrope (refer to the emergency start procedurepage43).
89
10. MAINTENANCE
Propeller
COTTER PIN
Mainless)
SPECIAL SPLINE WASHER PROPELLER
CASTLE NUT
PLAIN WASHER COTTER PIN (stainless)
Installation:
Install the thrust washer with the grooved side toward the gear case, then install the new propeller in the reverse sequence of removal. Hand tighten the castle nut until the 4 mm cotter pin can be installed. If necessary, tighten the castle nut just enough to align the hole with the groove in the nut.
MARINE GREASE -asiih
THRUST WhER
If the propeller is damaged, replace it as follows:
Removal: Remove the c:otterpin then remove the 16 mm castle nut, 17 mm plain washer, 10 mm special spline washer, propeller and thrust washer.
Use a new genuine Honda cotter pin and bend the cotter pin ends as shown.
90
10. MAINTENANCE
Submerged Motor
A submergedmotor must be serviced immediately after it is recovered from the water in order to minimize corrosion. Immediately take the outboard motor to the closest authorized Honda Marine dealer or if you are far from a dealership, proceed as follows: 1. Removethe engine cover, and rinse motor with fresh water to remove salt
water, sand, mud, etc. DRAIN SCREW EMERGENCY STAR+ER ROPE
B Gasoline is extremely flammable, and gasoline vapor can explode, causing serious injury or death. Do not smoke or allow flames or sparks in your working area. KEEP OUT OF REACH OF CHILDREN.
2. Loosen the carburetor dram screws, drain the contents of the carburetors into an approved gasoline container, then tighten the dram screws. 3. Disengage the emergency stop switch clip from the emergency stop switch and remove the spark plugs.
4. Remove the flywheel cover following the emergency starting procedure (refer to page 43) and remove the water from the cylinders by pulling the emergency starter rope several times. If the motor was running when it submerged,there may be mechanical damage, such as bent connecting rods. If the engine binds when rotated with the emergency starter rope, do not proceed or attempt to run the motor until it has been repaired.
91
10. MAINTENANCE
INOTICE] Running the outboard motor without suffkient cooiing water will damage the water pump and overheat the engine. 7. Engage the emergency stop switch clip with the emergency stop switch and attempt to start the engine (be sure the water level is at least 2 inches above the ventilation plate). If the engine fails to start, remove the spark plugs, clean and dry the electrodes, then reinstall the spark plugs and attempt to start the engine again. If the engine starts, and no mechanical damage is evident, continue: to run the engine for a I/2 hour or longer. If there was water in the engine crankcase, or the used engine oil showed signs of water contamination, then a second engine oil change should be performed after running the engine for a l/2 hour.
l l l
8. Take the outboard motor to your closest authorized Honda Marine dealer for inspection and service as soon as possible.
5. Changethe engine oil (refer to page 78). 6. Put a teaspoon of engine oil into each spark plug hole, then rotate the engine using the pull starter rope several times to lubricate the inside of the cylinders. Reinstall the spark plugs.
92
11. STORAGE
For longer service life of the outboard motor, have your outboard motor serviced by an authorized Honda Marine dealer before storage. If you are unable to take the motor to your dealer, proceed as follows:
f2 CARBURETOR DRAIN SCREW #I CARBURETOR
Draining the Carburetors

B Gasoline is extremely flammable, and gasoline vapor can explode, causing serious injury or death. Do not smoke or allow flames or sparks in your working area. KEEP OUT OF REACH OF CHILDREN. Be careful not to spill gasoline. Spilled gasoline or gasoline vapor may ignite. If any gasoline is spilled, make sure the area is dry before storing or transporting the motor. Do not smoke or allow flames or sparks where gasoline is drained or stored.
DRAIIi SCREW DRAIN SCREW
1. Disconnect the fuel hose connector. 2. Pull the #3 carburetor drain hose outside of the motor pan. 3. Loosen the drain screw of the #3 carburetor and dram the carburetor. Catch the draining gasoline in an approved gasoline container. 4. Drain the #l and #2 carburetors in the samemanner using the #3 carburetor dram hose.
5. After thoroughly draining the carburetors, tighten the drain screws securely. 6. Reinstall the drain hose back on the #3 carburetor.
93
11. STORAGE
Outboard Motor Position
CASE PROTECTORS
Transport and store the motor either vertically or horizontally, as shown above. Store the outboard motor in a well-ventilated area free from direct sunlight and humidity. Vertical transport or storage: Attach the stem bracket to stand.
Horizontal transport or storage: Rest the motor on the case protectors. lNoTlCE/ Improper transport or storage can damage the motor or cause oil leakage.
94
12. TROUBLESHOOTING
(1) Engine does not start. Fuel Fuel is not fed to carburetor.
l
There is no gasoline in fuel tank. Vent knob is not open or vent clogged. Fuel filter is clogged. Fuel line is kinked. Fuel line is connected improperly. Fuel pump is faulty. Primer bulb is faulty. Check valve in connector is faulty
No sparksacrossspark plug gap
- Sparkplug is faulty.
-E
Contamination Incorrect gap Broken sparkplug Pulser coil is faulty. Current leaks from high tension cord. C.D.I. unit is faulty. Exciter coil is faulty. Ignition coil is faulty. Wire harnessis faulty.
-llE
clogged. Electrical Sparks across sparlcplug gap

l
Insufficient sparks Normal spark
Spark plug gap is small. Weak starter motor rotation. Recheck the fuel system.
. Current leaks from engine stop switch cord. - Stop switch doesnot return satisfactorily. - Sparkplug is improperly installed. - Emergencystop switch is improperly installed. . Shift lever is not in N position.
95
12. TROUBLESHOOTING
(2) Engine starts but immediately stops. Engine some times stops while cruising. Fuel . No gasoline in fuel tank. There is gasoline in fuel tank. Wateris mixed with gasoline. Vent knob is not open or vent is clogged. Fuel filter is clogged. Air screw is open too wide. Idling speedis too slow. Carburetor vent is clogged. Fuel pump is faulty. Air in fuel pump. Air entersthrough fuel line connector. Air entersthrough primer bulb.
Engine overheats . Normal sparking Water intake screens are clogged. Spark plug is not of specified rating. Water pump is faulty. Thermostat is clogged. Thermostat is faulty. Water tube or passage is clogged. Exhaust gas is entering cooling system.
Iii L
-
!iE
96
13. SPECIFICATIONS
Electric starter C.D.1 Lubrication system Trochoid pump pressurelubrication Specified oil Engine: API standard (SG SF/CC CD) SAE low-30 Gear case: API standard (GL-4/S) SAE 90 outboard motor gearoil Oil capacity Engine: 2.5 US qt (2.4 lit.) Gear case:0.53 US qt (0.5 lit.) D.C. output BSAG, BLAG 12V-6A BAPU 12V-1OA Cooling system Water cooling with thermostat Exhaust system Thru-hub Spark plugs DRIIEA, X22ESR-U Fuel pump Diaphragm type Fuel Automotive gasoline (91 researchoctane, 86 pump octane) Tank capacity 6.6 US gal. (25 lit.) Gear change Forward-Neutral-Reverse (dog type) Steering angle 37.5 right and left Transom angle 5 stages (11.5, 15.5, 19.5, 23.5, 27.5) Starter system Ignition system
97
13. SPECIFICATIONS
API standard SG SF/CC CD
98
14. WARRANTY
Owner Satisfaction Your satisfaction and good will are important to your dealer and to us. All Honda warranty details are explained in the Distributors Limited Warranty. Normally, any problems concerning the product will be handled by your dealers service department. If you have a warranty problem that has not been handled to your satisfaction, we suggest you take the following action:
l
SERVICE
American Honda Motor Co., Inc.
Honda Power Equipment Division CustomerService Office 4475 River GreenParkway Duluth, GA 30136-2565 Or telephone:(404) 497-6400 We will need the following information in order to assist you: - You name, address,and telephone number - Product model and serial number - Date of purchase - Dealer name and address - Nature of the problem
Discuss your problem with a member of dealership management. Often complaints can be quickly resolved at that level. If the problem has already been reviewed with the Service Manager, contact the owner of the dealership or the General Manager. If you are dissatisfied with the decision madeby the dealerships management, contact the Honda Power Equipment CustomerService Office, You can write to:
After reviewing all the facts involved, you will be advised of what action can be taken. Pleasebear in mind that your problem will likely be resolved at the dealership, using the dealers facilities, equipment, and personnel, so it is very important that y?ur initial contact be with the dealer. Your purchase of a Honda product is greatly appreciated by both your dealer and American Honda Motor Co., Inc. We want to assist you in every way possible to assureyour complete satisfaction with your purchase.
99
Current customer service contact information:

Your owner's manual was written to cover most of the questions you might ask about your Honda. Any questions not answered in the owner's manual can be answered by your Honda dealer. If your dealer doesn't have an immediate answer, they should be able to get it for you. If you have a difference of opinion with your dealer, please remember that each dealership is independently owned and operated. That's why it's important to work to resolve any differences at the dealership level. If the service personnel are unable to assist you, please discuss your concerns with the dealer management such as the Service Manager or the dealership's owner. If you need to contact American Honda regarding your experiences with your Honda product or with your dealer, please send your comments to the following address: American Honda Motor Co., Inc. Marine Division Customer Relations Office 4900 Marconi Drive Alpharetta, GA 30005-8847 Or telephone: (770) 497-6400 M-F, 8:30 am - 7:00 pm EST When you write or call, please provide the following information: Your name, address and telephone number (complete with area code) Model and complete serial number Date of purchase Name and location of the selling dealer Name and location of the servicing dealer (if different) A detailed description of your concerns
15. WIRING DIAGRAM

TILLER HANDLE TYPE
ml-pW - r*rra
r-
100
15. WIRING
REMOTE CONTROL TYPE
DIAGRAM
!s-
15. WIRING DIAGRAM

REMOTE CONTROL, POWER TRIM/TILT TYPE .-.. -P
XRTA type outboard
I I I I I
I I I I I I I I I I I I I I
I I
L------------A
102
16. INDEX
Anode metal ....................................................................24 Pre-operation check ................................................... 33 Motor protection system............................................. 65 Battery (not included) ......................................................83 Break-in procedure...........................................................49 Choke knob ..................................................................... 11 Choke/fast idle lever ....................................................... 18 Cleaning and flushing .....................................................72 Component identification ................................................. 8 Controls & instruments (common) .................................. 23 Controls Gas assistedtilt type _ ..................................................22 Tiller handle type ....................................................... 11 Remote control type ................................................... 15 Remote control & power trim/tilt type ....................... 20 Cooling system indicator ................................................24 Cruising Tiller handle type.. ......................................................5 1 Remote control type ...................................................53 Emergency starting .........................................................43 Emergency stop switch lanyard Tiller handle type ........................................................ 13 Remote control type ................................................... 17 Engine cover removal/installation .................................. 28 Engine fuel filter .............................................................86 Engine Oil Level check .......................................................... 29 Change ..................................................................78 Pressureand overheat warning system ................ 62 Over-rev limiter .........................................................27 Start button ................................................................. 11 Stop switch ................................................................ 13 Fuel Cap/gauge/vent knob ................................................. 27 Level ........................................................................ 30 Line connection .........................................................34 Tank and filter ............................................................88 Fuse replacement ............................................................89 Gasoline containing alcohol ............................................ 3 1 Gear oil .........................................................................80 Gear shifting Tiller handle type.. ...................................................... Remote control type ...................................................z; High altitude operation ....................................................67 Ignition switch ................................................................ 16 Lubrication ......................................................................85 Maintenance ....................................................................74 Schedule ....................................................................76 Manual Choke knob ................................................................. 18 Relief valve Controls.. ...............................................................22 Operation ...............................................................59 Motor protection system .................................................. 62 Neutral release lever ....................................................... 16
103
16. INDEX
Oil pressure indicator light .............................................. 14. Oil pressure indicator light/buzzer .................................. 19 Other checks .................................................................... 33 Over-rev limiter ............................................................... 64. Overheat indicator light .................................................. 14. Overheat indicator light/buzzer ....................................... 19 Power tilt switch (motor pan) Controls ...................................................................... 21 Operation ................................................................... 59 Power trim warning system ............................................ 64 Power trim/tilt switch (remote control lever) .................. 20 Pre-operation checks ....................................................... 28 Propeller .......................................................................... 90 And cotter pin ............................................................ 3:! Remote control Friction adjustment .................................................... 33 Lever ......................................................................... 1.; Safety ........................................................................... 6 Information .................................................................. 7 Labels .......................................................................... 6 Shallow water operation .................................................. 66 Shift lever ........................................................................ 11 Spark plug ....................................................................... 82 Specifications .................................................................. 97 Starting the engine Remote control type .................................................. 40 Tiller handle type ....................................................... 36 Steering ........................................................................ 51 Friction adjustment (common) .................................. 32 Stem bracket 33 Pre-operationcheck ..................................................... Stopping the engine Remote control type .................................................. 70 liller handle type.. ...................................................... 68 Storage ........................................................................ 94 Submerged motor ............................................................ 91 Tachometer ...................................................................... 21 Throttle Friction knob ............................................................. 12 Grip ........................................................................ 12 Opening indicator ...................................................... 12 Tilt lever ......................................................................... 22 Tilt lock lever Controls ...................................................................... 23 Operation ................................................................... 60 Tilting motor Gas assisted tilt type .................................................. 54 Power trim/tilt type .................................................... 57 Tool kit ......................................................................... 33 Tool kit and spare parts ................................................... 75 Transom angle adjusting rod ........................................... 26 Transporting .................................................................... 7 1 Trim meter Controls ...................................................................... 21 Operation .................................................................... 58 Trim tab ........................................................................ 23
104
16. INDEX
Trim tab adjustment ........................................................61 Troubleshooting ..............................................................95 Starting problems .......................................................48 Warranty service .............................................................99 Water intakes ...................................................................25 Wiring diagram ............................................................. 100
105
MEMO
MEMO
MEMO
mmwnr-
HONDA
BF35A145A Owner's Manual

1I 1I I 11I <SUPPLEMENT>-
@ 1993 American I I I I
Honda
Motor
Co., inc. - All Rights
Reeerved
I I I I I I I I I I
Thank you for purchasing a Honda Outboard Motor. This owners manual supplement covers specific information about the Honda BF45AM LHTA type outboard motor. Refer to the BF35A/45A owners manual for all other information. The owners manual and this supplement contain information on how to operate your new outboard motor safely. Please read them carefully.
Keep the owners manual and this supplement handy, so you can refer to them at any time, and be sure they accompany the outboard motor if you sell it. We recommend that you mad the warranty policy to fully understand your rights and nxponsibilities. The warranty policy is a separate document provided by your dealer.
The information in this publication was in effect at the time of approval

for printing. American Honda Motor Co., Inc. merves the right to discon-
tinue or change specifications or design at any time without notice and without incurring any obligation whatever. No part of this publication may be reproduced without written permission.
01993 AmeticanHondaMotorCo.,Inc. All Rights Reserved .
TYPES OF HONDA BF35A/45A OUTBOARD MOTORS

It may be necessary to refix to this chart for reference purposes when reading this manual. 1 Model Shaft Length Short BF35
SHA
l
TiIler Handle
I-m2
0
Remote Control
Gas Assisted Power Trim/ Tachometer Tilt Tilt

0
Trim Meter
LHA LRA
0 0
0 0
0 a I
BF45
S: Short Shaft
L: Long Shaft
H: Tiller Handle
R: Remote Control
T: Power TkQIilt
The gas assisted tilt type motors use a gas damper to assist when manually tilting the motor. The power trim/tilt type motors use an electric/hydraulic power cylinder to trim or tilt the motor.
CONTENTS (LHTA)
2. COMPONENT IDENTIFICATION ........... 3. CONTROLS Tiller handle 8z power trim/tilt type Ignition switch .......................... Emergency engine stop switch. ............. Power trim/tilt switch (optional part). ........ Power tilt switch (motor pan). .............. Trimmeter ............................. Tachometer. ............................ Manual relief valve. ...................... 4. PRE-OPERATION CHECKS Steering friction adjustment. ................. 5. STARTING THE ENGINE Starting the engine ......................... Emergency starting. ........................ 6. OPERATION Motor protection system Power trim warning system ................ Shallow water operation. .................. 7. STOPPING THE ENGINE Tillerhandle &powertrim/tilttype ............
4 10. MAINTENANCE Auxiliary fuse replacement . . . . . . . . . . . . . . . . . . 13 5 5 6 7 7 7 8 9 10 10
15. WIRING DIAGRAM.. . . . . . . . . . . . . . . . . . . . . . 14 [d,l 17. OPTIONALPARTS . . . . . . . . . . . . . . . . . . . . . . . 15
sections required no changes Thefrom the BF35A/45A owners manual. I&se sections ate not covered in this supplement. The NON-HIGHLIGHTED sections contain only new information about the BP35A/45A LHTA. Refer to the BP35A/45A owners manual for all other information. I
11 11 12
2. COMPONENT
IDENTIFICATION
(LHTA)
POWER TILT SWITCH BUZZER
3. CONTROLS (LHTA)
Ignition Switch
INSTRUMENT HOUSING
Emergency Engine Stop Switch

(optionalpart)
IGNITIO SWITCH
EMERGENCY ENGINE STOP SWITCH
The LHTA type is equipped with a key type ignition switch which can be mounted in the optional instrument housing. Key positions: START To activate the starter motor and start the engine the shift lever must he in the neutral position.
ON To run the engine after starting. The battery will discharge if the key is left in this position with the engine not running. OFF To stop the engine (IGNITION OFF).
The emergency engine stop switch should not be used to normally stop the engine. Use the ignition switch to nonnalIy stop the engine.
3. CONTROLS (LHTA)
Power Trim/Tilt Switch (foot or tiller handle)
The outboard motor will be equipped with either a foot or tiller handle power trim/tilt switch. Power Trim Press the power trim/tilt switch to adjust the motor trim angle of 0" to 20 to maintain proper boat trim. The power trim/tilt switch can be operated while the boat is under way or while stopped. By using the power trim/tilt switch the operator can change the trim angle of the motor to achieve maximum boat acceleration, speed, stability and maintain optimum fuel c43nsumption. Power Tilt Press the power trim/tilt switch to adjust the motor tilt angle of 20 to 6o. By using the power trim/tilt switch the operator can change the tilt angle of the motor for shallow water operation, beaching, launching from a trailer, or mooring. Foot Switch
FOOT SWITCH
Tiller Handle Switch

TILLER HANDLE
POWiR TRIM/TILT SWITCH POWER TRIM/TILT SWITCH
1 NOTICE 1 Excessive trim/tilt angle during operation can cause the propeller to raise out of the water and cause propeller ventilation and engine over-revving. Excessive trim/tilt angle can also damage the water pump.
3. CONTROLS (LHTA)
Power Tilt Switch (motor pan) Trim Meter
TRIMMETER
Tachometer
TACHOMETER
POWER TILT SWITCH
The power tilt switch located on the motor pan is a convenience switch for tilting the motor for trailering, or performing outboard maintenance. This power tilt switch should only be operated with the boat stopped and motor off.
The trim meter has a range of 0 to 20 and indicates thb trim angle of the outboard motor. Refer to the trim meter when using the power trim/tilt switch to achieve proper boat performance.
The tachometer shows the approximate engine speed in revolutions per minute. Refer to the tachometer when using the power trim/tilt switch to achieve proper boat and motor performance. An instrument light switch can be installed to control the instrument light circuit.
3. CONTROLS (LHTA)
Manual Relief Valve
If the power trim/tilt switch will not tilt the outboard motor, the motor can be manually tilted up or down by opening the manual relief valve. To tilt the outboard motor manually, turn the manual valve under the left stem bracket no more than 1 or 2 tums counterclockwise using a screw driver. After tilting the motor, turn the manual relief valve clockwise securely. The manual relief valve must be tightened securely before operating the motor or the motor could tilt up when operating in reverse.
LEmSTERNBRACKET
MANUAL
Do not turn this screw. If this screw is turned, hydraulic oil will bleed out of the power trim/tilt system. Should this happen it will be necessary to consult your authorized Honda Marine dealer and have the system refilled.
MANUALI~ELIEFVALVE
4. PRE-OPERATION
Steering Friction Adjustment
TO DECREASE STEERING
CHECKS (LHTA)
Operate the tiller handle right and left and check for the amount of drag felt. Tighten the adjuster until the steering operates comfortably and safely. Check the steering friction adjustment with the motor trimmed in all trim angle positions. The steering effort will change with various trim angles.

Starting the Engine
4. Turn the ignition key to the START position and release the key when the engine starts. Ihe starter motor consumes a large amount of cumznt. Do not run it continuously for more than 5 seconds at a time. If the engine does not start within 5 seconds wait at least 10 seconds before using the starter motor again. 1 NOTICE 1 Donottumtheignition key to the start position while the engine is running. This can damage the starter motor and flywheel.
Emergency Starting
1 NOTICE 1 The propeller must be lowered into the water. Running the outboard motor out of the water will damage the water pump and overheat the engine. Ihe steps for starting the BF45A LHTA are the same except step 4. The new inforination for step 4 is
ShOWll.
The steps for emergency starting the BF45A LHTA are also the same except step 5. 5. lbm the ignition key to the ON position. Engage the emergency stop switch clip, located at one end of the emergency stop switch lanyard, with the emergency engine stop switch.
10
6. OPERATION
Power Trim Warning System
The intermittent buzzer will not sound & beep at one second intervals when:
l
(LHTA)
Shallow Water Operation

When operating in shallow water, tilt the motor up to prevent the propeller and gear case from hitting the bottom (refer to the BF35A/45A Owners Manual for additional information). Use the minimum amount of throttle opening necessary to maintain sat% boat control. The motor should not be trimmed so high that the cooling system indicator stops discharging water. Monitor the cooling system indicator for sufficient water discharge when the motor is tilted beyond 20.
the motor is in gear and the trim angle is less than 20 with the throttle in any position. the motor is in neutral and the trim angle and/or throttle are in any position.
When the power trim warning system is activated: An intennittent buzzer wig sound & beep at one second intervals when:
l
1. Reduce the trim angle to less than 20 if possible. 2. Reduce the throttle opening to SLOW and operate the boat at a slow speed.
the motor is in gear and the trim angle is mom than 20 with the throttle in any position. the motor is in neutral and the trim angle is more than 20 with the starter motor cranking.
11
7. STOPPING THE ENGINE (LHTA)

Normal Engine Stop
IGNRION KEY
The steps for stopping the BF45A LHTA are the same except step 2. The new information for step 2 is
ShOWn.
2. Turn the ignition key to the OFF position. When the ?&at is not in use, remove and store the ignition key. 1 NOTICE 1 The battery will discharge if the ignition is left on with the engine not running.
12
_ 10. MAINTENANCE
Auxiliary Fuse Replacement
I P4 1
BLOWN FUSE
WIRING HARNESS \
FUSE HOLDER CAP
CABLE TIE /
AUXILIARY FUSE RATING: 10A If the auxiliary fuse is blown, the electric starter will not work but the power trim will work. If the main fuse is blown, neither the starter or the power trim will work. Ihe main fuse is located on the solenoid bracket inside the engine cover. Never use a fuse with a different rating from that specified. If the fuse is blown, check the cause, then replace the fuse with a fuse of the same rated capacity. Unless the cause is found, the fuse may blow again.
RUBBER END CAPS
Replacement 1. Stop the engine. 2. Loosen the cable tie and slide it down the wiring harness. 3. Slide the rubber end caps back. 4. Unscrew the fuse holder cap. 5. Remove the fuse. 6. Install a new 10A fuse.
If a spam fuse.is not available, the motor will need to be started with the pull starter rope (refer to the emergency start procedure).
13
15. WIRING DIAGRAM (LHTA)
17. OPTIONAL PARTS (LHTA)

POWER TRIM/TILT SWITCHES Foot Qpe Extended Tiller Handle I)pe
Foot Hamess
Extended Tiller Handle Harness
17. OPTIONAL PARTS (LHTA)

INSTRUMENT HOUSING
There axe additional optional parts available. See your authorized Honda Marine dealer for a complete list.
16
1 I 31 ZV36OS 00X31 -ZV3-6SO0 PRINTED 2509304 IN U.S.A.
I I

Honda BF35

Uploaded by

Copyright:

Available Formats

Honda BF35

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Honda BF35

Uploaded by

Copyright:

Available Formats

What are the different types of Honda BF35A/45A outboard motors?

What are the different types of Honda BF35A/45A outboard motors?

What information should be recorded for identification purposes?

What information should be recorded for identification purposes?

Includes 31ZV360S supplement for the BF45A LHTA

HONDA MOTOR CO., LTD. 1990, ALL RIGHTS RESERVED

TYPES OF HONDA BF3A/45A OUTBOARD MOTORS

X: Extra Long Shaft

on, PReS\SURE INDICATOR LIGHT

THdT 1 LOCK STERN BRACKET

OVERHEAT INDICATOR LIGHT ENGINE STOP .l-..CH

THROTTLE _____- ~~~ FRICTION KNOB

ACCESS COVER ANTI-VENTILATION D, ATE-

WASH PLUG (Flush plug) I GEAR OIL DRAIN PLUG

OIL PRESSURE INDICATOR

COOLING TRANSOM ANGLE INDICATOR

In! - STERN BRACKET /

CHOKE/FAST IDLE LEVER

ETAL) HAUST PORT \ PROPELLER

~BNTHATION __ .-.rwn. .,m

EMERGENCY STOP SWITCH LANYARD EMERGENCY STOP SWITCH CLIP

-/ EMERGENCY ENGINE STOP SWITCH

FUEL CAP TACHOMETER

FiJEL HOSE CONNECTOR (FEMALE)

EN&NE START BUTTON

Throttle Friction Knob

The curve on the grip indicates throttle opening.

ENGINE STOP SWITCH \

EMERGENCY ENGINE STOP StiTCH

STOP SWITCH CLIP EMERGENCY STOP SWITCH LANYARD

Push the engine stop switch to stop the engine.

OIL PRESSURE INDICATOR LIGHT

REMOTE CONTROL LEVER

3. CONTROLS (REMOTE CONTROL TYPE)

SPAkE EMERGENCY STOP SWITCH CLIP

3. CONTROLS (REMOTE CCDNTROL TYPE)

Manual Choke Knob

CHOKE/FAST IDLE LEVER

Overheat Indicator Light/Buzzer

& POWER TRIM/TILT

control lever) Power Ikim

Power Trim Do not trim this engine when you are

using a large amount of throttle

motor trim angle of 0 to 20 to maintain proper boat trim. The power

& POWER TRIM/TILT

TRIM METER POWER TILT SWITCH

3. CONTROLS (REMOTE CONTROL & POWER TRIM/TILT

Tilt Lever (GAS ASSISTED TYPE)

MANUAL POWER m rel=1

3. CONTROLS & INSTRUMENTS

ANODi (stem bracket)

3. CONTROLS & INSTRUMENTS

ANGLE ADJUSTING ROD UNLOCKED POSITION I 1 . ----/ J

TRANSOM ANGLE ADJUSTING ROD

FUEL FILLER CAP

SCREWDRIVER HANDLE Bg+J 18 x 19 mm WRENCH

5. STARTING THE ENGINE

(FUEL TANK END) \

5. STARTING THE ENGINE (TILLER

EilERGtiCY STOP SWITCH LANYARD