Gas Turbine in Cairo North Power Station
Gas Turbine in Cairo North Power Station
Gas Turbine in Cairo North Power Station
4.1 Introduction
In this chapter we are going to discuss how gas turbine works, the classification of gas turbine, the component of the gas turbine and the using of fuel and air to produce power. Air is the working fluid and the fuel is heating source in combustion process to heat the air. Also in this chapter starting up will be discussed.
1. Single shaft gas turbine. 2. Open cycle gas turbine. 3. Horizontal gas turbine.
With single shaft turbine, the compressor, turbine and generator are mounted on a single shaft. In this arrangement, the compressor and turbine rotate at the same speed. This is shown in figure (4.1) which shows the way of connecting all the devices together on a single shaft.
dc220.4shared.com/doc/u2BZFNqQ/preview.html
1/38
09/05/2012
Fig. 4.1 The compressor, turbine and generator are mounted on a single shaft
A simple open cycle gas turbine consists of a compressor, combustion chamber and a turbine, the compressor takes in ambient air and raises its pressure. Heat is added to the air in combustion chamber by burning the fuel and raises its temperature. The heated gases coming out of combustion chamber are then passed to the turbine where it expands doing mechanical work. This is shown in figure (4.2).
dc220.4shared.com/doc/u2BZFNqQ/preview.html
2/38
09/05/2012
1. Starting motor. 2. Air inlet and filter. 3. Compressor. 4. Combustion chamber. 5. Turbine. 6. Exhaust.
The solenoid also closes high-current contacts for the starter motor, which begins to turn. Once the engine starts, the key-operated switch is opened; a spring in the solenoid assembly pulls the pinion gear away from the ring gear, and the starter motor stops. The starter's pinion is clutched to its driveshaft through an overrunning sprag clutch which permits the pinion to transmit drive in only one direction. In this manner, drive is transmitted through the pinion to the flywheel ring gear, but if the pinion remains engaged the pinion will spin independently of its driveshaft. This prevents the engine driving the starter, for such back drive would cause the starter to spin so fast as to fly apart. Figure (4.3) shows the starter installed underneath gas turbine.
dc220.4shared.com/doc/u2BZFNqQ/preview.html
3/38
09/05/2012
dc220.4shared.com/doc/u2BZFNqQ/preview.html
4/38
09/05/2012
Air quality can have an enormous impact on gas turbine performance and reliability and is heavily influenced by the surrounding environment in which the unit is installed. Furthermore, within any given location, the quality of air can change dramatically over a years time or, in some situations, within hours. Poor air quality leads to compressor fouling. The next figure (4.5) shows the air filter in the power plant.
dc220.4shared.com/doc/u2BZFNqQ/preview.html
5/38
09/05/2012
The air inlet system consists of the following: A filter house with weather hoods, an automatic self cleaning filtration system using high efficiency filter elements, and an inlet ducting system. Air enters the filter house and continues through the transition piece, the acoustical silencer, the inlet heating module, the trash screen, and then to the turbine compressor through the inlet plenum. The elevated filter house arrangement provides a compact system that minimizes the pickup of dust in the filter house. The inlet system makes use of materials and coatings in its construction, which are designed to require minimal maintenance. All external and internal surface areas (exposed to airflow) of the filter house are coated with a protective corrosion- preventive inorganic-zinc primer and epoxy overcoat.
a) Diffuser: Is used to pull air into the housing. b) Hoods: Work to guide the air into the filter housing. c) Socks filter: Used to capture dust and particulates from the air. d)Filters canister : Any tower Consists of number of filters in 5 rows each filter divided into two parts the first having cylindrical shape and the second having cone shape, each row having 160 filter with total number 800 filter per tower. The cylindrical shape filters is shown in figure (4.6). e) Pulsation nozzle: make a back flow to clean the filters taking the air from air processing unit. This is shown in figure (4.7).
dc220.4shared.com/doc/u2BZFNqQ/preview.html 6/38
09/05/2012
dc220.4shared.com/doc/u2BZFNqQ/preview.html
7/38
09/05/2012
f) Evaporative cooling media: used to cool the air by remove water vapor from the air. g) Mist eliminator: separated water droplet from the air. h) Silencer: reduce the noise.
Internal lighting is provided for the filter change out areas. Details for the operation and maintenance of the inlet filtration system are contained in the maintenance manual in this section. Access for maintenance and inspection of the filter elements are by use of stairs and outside platform in conjunction with lower level exterior doors and access platforms at each level in the filter house as shown in Figure (4.8).
The inlet silencer consists of an acoustically lined duct, which contains silencing baffles constructed of mineral wool insulation wrapped with fiberglass cloth and encapsulated by
dc220.4shared.com/doc/u2BZFNqQ/preview.html 8/38
09/05/2012
perforated, stainless steel sheet metal. The inlet bleed heat system consists of a series of stainless steel pipes mounted onto the section of duct work immediately following the silencer. A manifold external to the duct distributes air to these vertical pipes extending into the duct. Within the duct, the bleed air is dispersed to the inlet airflow through a series of holes integral to the distribution pipes. The elbow houses the single piece, stationary, stainless steel trash screen. The purpose of the trash screen is to protect the compressor from loose pieces of hardware from the filter house, ductwork, or through maintenance error. A removable access panel is positioned upstream of the trash screen for cleaning and inspection purposes. The inlet duct system also contains provisions for the dew point humidity sensor used in monitoring the airflow downstream of the inlet bleed heat module. The sensor minimizes the performance degradation associated with the inlet bleed heat system through communication with the Mark V to keep all parts of the inlet system at arelative humidity below the frost point. The location of the humidity sensor is shown on the Inlet and Exhaust Flow Diagram.
4.3.3 Compressor
4.3.3.1 General
The axial-flow compressor section consists of 17 stages of the compressor rotor and the compressor casing. Within The compressor casings are the variable inlet guide vanes, the various stages of rotor and stator balding, and the exit guide vanes. In the compressor, air is confined to the space between the rotor and stator where it is compressed in stages by a series of alternate rotating (rotor) and stationary (stator) airfoilshaped blades. The rotor blades supply the force needed to compress the air in each stage and the stator blades guide the air So that it enters the following rotor stage at the proper angle. The compressed air exits through the compressor discharge casing to the combustion chambers. Air is extracted from the compressor for turbine cooling and for pulsation control during startup. Air may also be extracted from the compressor when the combustion turbine is operating for use in the plant compressed air system. The next figure (4.9) shows the stages of
dc220.4shared.com/doc/u2BZFNqQ/preview.html 9/38
09/05/2012
compressor.
The compressor portion of the gas turbine rotor is an assembly of wheels; a speed ring, tie bolts, the compressor rotor blades, and a forward stub shaft. Each wheel has slots broached around its periphery. The rotor blades and spacers are inserted into these slots and held in axial position by staking at each end of the slot. The wheels are assembled to each other with mating rabbets for concentricity control and are held together with tie bolts. Selective positioning of the wheels is made during assembly to reduce balance correction. After assembly, the rotor is dynamically balanced. The forward stub shaft is machined to provide the thrust collar, which carries the forward and aft thrust loads. The stub shaft also provides the journal for the No. 1 bearing, the sealing surface for the No. 1 bearing oil seals and the compressor low-pressure air seal. The
dc220.4shared.com/doc/u2BZFNqQ/preview.html 10/38
09/05/2012
stage 17 wheel carries the rotor blades and also provides the sealing surface for the highpressure air seal and the compressor-to-turbine marriage flange. The next figure (4.10) shows the Compressor Rotor Assembly.
The casing area of the compressor section is composed of three major sections. Which are?
1. Inlet casing. 2. Compressor casing. 3. Compressor discharge casing.
These casings, in conjunction with the turbine casing, form the primary structure of the gas turbine. They support the rotor at the bearing points and constitute the outer wall of the gasdc220.4shared.com/doc/u2BZFNqQ/preview.html 11/38
09/05/2012
path Annulus. All of these casings are split horizontally to facilitate servicing.
1. Inlet Casing
Inlet guide vanes used at compressor inlet to ensure the air enters the first stage rotor as desired angle, Variable inlet guide vanes are mechanically positioned, by a controlling and pinion gear arrangement connected to a hydraulic actuator drive. This is shown in figure (4.11).
2. Compressor Casing
The forward compressor casing contains the stage 0 through stage 4 compressor stator stages. The compressor casing lower half is equipped with two large integrally cast trunnions which are used to lift the gas turbine when it is separated from its base. The aft
dc220.4shared.com/doc/u2BZFNqQ/preview.html 12/38
09/05/2012
compressor casing contains stage 5 through stage 12 compressor stator stages. Extraction ports in casing permit removal of 13th-stage compressor air. This air is used for cooling functions and is also used for pulsation control during startup and shutdown. Figure (4.12) show casing.
The compressor discharge casing is the final portion of the compressor section. It is the longest single casting, is situated at midpoint - between the forward and supports keystone of the gas turbine structure. The compressor discharge casing contains the final compressor stages, forms both the inner and outer walls of the compressor diffuser, and joins the compressor and turbine casings. The discharge casing also provides support for the combustion outer casings and the inner support of the first-stage turbine nozzle. The compressor discharge casing consists of two cylinders, one being a continuation of the compressor casing and the other being an inner cylinder that surrounds the compressor rotor. The two Cylinders are concentrically positioned by fourteen radial struts. A diffuser is formed by the tapered annulus between the outer cylinder and inner cylinder of the discharge casing. The diffuser converts some of the compressor exit velocity into added static pressure for the combustion air supply. This is shown in figure (4.13).
dc220.4shared.com/doc/u2BZFNqQ/preview.html
13/38
09/05/2012
The compressor rotor and stator blades are airfoil shaped and designed to compress air efficiently at high blade tip velocities. The blades are attached to the compressor wheels by dovetail arrangements. The dovetail is very precise in size and position to maintain each blade in the desired position and location on the wheel. The compressor stators blades are airfoil shaped and are mounted by similar dovetails into ring segments in the first five stages. The ring segments are inserted into circumferential grooves in the casing and are held in place with locking keys. The stator blades of the remaining stages have a square base dovetail and are inserted directly into circumferential grooves in the casing. Locking keys hold them in place. The bleeding process is shown in figure (4.14).
dc220.4shared.com/doc/u2BZFNqQ/preview.html
14/38
09/05/2012
Compressor stall or surge is not peculiar to any one particular brand or type of engine. It may occur on any turbine engine if conditions are right. Stall has been uncountered on twostage or turbo-supercharged piston engines, so there is no need to look upon stall as some mysterious product of gas turbine engines. Any number of mechanical defects, such as bad spark plugs, lean arburetion, poor timing, or sticking valves, can result in reciprocating engines backfiring. Similarly, for gas turbine engines, maintenance or flight conditions can influence the compressor stall or surge appreciably. The condition and operation of the bleed valve and fuel system components are of vital importance in maintaining surge-free operation. Why are engines at risk of surge? As engines are designed to meet demands for higher power or lower specific fuel consumption, the engines must accommodate.
1. Increased mass airflow. 2. Increased pressure (compression) ratio. 3. Increased maximum allowable turbine inlet and outlet temperatures. 4. Improved efficiency of the compressor and turbine sections.
dc220.4shared.com/doc/u2BZFNqQ/preview.html
15/38
09/05/2012
Quick engine starts and rapid accelerations are also desirable. To provide higher power with low specific fuel consumption and acceptable starting and acceleration characteristics, it is necessary to operate as close to the surge region as possible. To prevent compressor stall or surge, fuel flow must be properly metered during the start and acceleration cycle of any gas turbine engine. To accomplish this, the example engine incorporates 5th and 10th stage acceleration bleed valves. In general, there are fewer surge problems on centrifugal compressors than on axial flow compressors. There are several reasons for the difference; the primary reason is that centrifugal flow compressors operate at somewhat lower pressure ratios than axial flow compressors. A surge from a turbine engine is the result of instability of the engine's operating cycle. As discussed earlier, the operating cycle of the turbine engine consists of intake, compression, combustion, and exhaust, which occur simultaneously in different places in the engine. The part of the cycle susceptible to instability is the compression phase. Compressor surge may be caused by engine deterioration, it may be the result of ingestion of birds or ice, or it may be the final sound from a severe engine damage type of failure. In a turbine engine, compression is accomplished aerodynamically as the air passes through the stages of the compressor, rather than by confinement, as is the case in a piston engine. The air flowing over the compressor airfoils can stall just as the air over the wing of an airplane can. When this airfoil stall occurs, the passage of air through the compressor becomes unstable and the compressor can no longer compress the incoming air. The highpressure air behind the stall further back in the engine escapes forward through the compressor and out the inlet. This escape is sudden, rapid and often quite audible as a loud bang. Engine surge can be accompanied by visible flames forward out the inlet and rearward out the tailpipe. Instruments may show high EGT and EPR or rotor speed changes; but, in many stalls, the event is over so quickly that the instruments do not have time to respond. Once the air from within the engine escapes, the reason (reasons) for the instability may self-correct and the compression process may re-establish itself. A single surge and recovery will occur quite rapidly, usually within fractions of a second. Depending on the reason for the cause of the compressor instability, an engine might experience:
dc220.4shared.com/doc/u2BZFNqQ/preview.html
16/38
09/05/2012
1. A single self-recovering surge. 2. Multiple surges prior to self-recovery. 3. Multiple surges requiring pilot action in order to recover. 4. A non-recoverable surge.
For complete, detailed procedures, flight crews must follow the appropriate checklists and emergency procedures detailed in their specific Airplane Flight Manual. In general, however, during a single self-recovering surge, the cockpit engine indications may fluctuate slightly and briefly. The flight crew may not notice the fluctuation. (Some of the more recent engines may even have fuel-flow logic that helps the engine self-recover from a surge without crew intervention. The stall may go completely unnoticed, or it may be annunciated to the crew for information only via EICAS messages.) Alternatively, the engine may surge two or three times before full self recovery. When this happens, there is likely to be cockpit engine instrumentation Shifts of sufficient magnitude and duration to be noticed by the flight crew. If the engine does not recover automatically from the surge, it may surge continually until the pilot takes action to stop the process. The desired pilot action is to retard the power lever until the engine recovers. The flight crew should then slowly re-advance the power lever. Occasionally, an engine may surge only once but still not self-recover. The actual cause for the compressor surge is often complex and may or may not result from severe engine damage. Rarely does a single compressor surge cause severe engine damage, but sustained surging will eventually over-heat the turbine, as too much fuel is being provided for the volume of air that is reaching the combustor. Compressor blades may also be damaged and fail as a result of repeated violent surges; this will rapidly result in an engine which cannot run at any power setting. As shown in figure (4.15).
dc220.4shared.com/doc/u2BZFNqQ/preview.html
17/38
09/05/2012
The combustion system is of the reverse-flow type with the 18 combustion chambers arranged around the periphery of the compressor discharge casing as. Combustion chambers are numbered counterclockwise when viewed looking downstream and starting from the top left of the machine. This system also includes the fuel nozzles, a spark plug ignition system, flame detectors, and crossfire tubes. Hot gases, generated from burning fuel in the combustion chambers, flow through the impingement cooled transition pieces to the turbine. High pressure air from the compressor discharge is directed around the transition pieces. Some of the air enters the holes in the impingement sleeve to cool the transition pieces and flows into the flow sleeve. The rest enters the annulus between the flow sleeve and the combustion liner through holes in the downstream end of the flow sleeve. This air enters the combustion zone through the cap assembly for proper fuel combustion. Fuel is supplied to each combustion chamber through five nozzles designed to disperse and mix the fuel with the proper amount of combustion air.
dc220.4shared.com/doc/u2BZFNqQ/preview.html
18/38
09/05/2012
Dual fuel-The DLN-2 combustion system shown in Figure (3.16) is a single stage, dual mode combustor capable of operation on both gaseous and liquid fuel. On gas, the combustor operates in a diffusion mode at low loads (<50% load), and a pre-mixed mode at high loads (>50% load). While the combustor is capable of operating in the diffusion mode across the load range, diluents injection would be required for NOx abatement. Oil operation on this combustor is in the diffusion mode across the entire load range, with diluents injection used for NOx. Figure (4.17) shows combustion chamber arrangement.
dc220.4shared.com/doc/u2BZFNqQ/preview.html
19/38
09/05/2012
The outer combustion chambers act as the pressure shells for the combustors. They also provide flanges for the fuel nozzle-end cover assemblies, crossfire tube flanges, spark plugs, flame detectors and false start drains. The flow sleeves form an annular space around the cap and liner assemblies that directs the combustion and cooling air flows into the reaction region. To maintain the impingement sleeve pressure drop, the openings for crossfire tubes, spark plugs, and flame detectors are sealed with sliding grommets. Figure (4.18) the flow sleeve assembly.
All combustion chambers are interconnected by means of crossfire tubes. The outer chambers are connected with an outer crossfire tube and the combustion liner primary zones are connected by the inner crossfire tubes. Figure (4.19) shows the crossfire tube.
dc220.4shared.com/doc/u2BZFNqQ/preview.html
20/38
09/05/2012
There are five fuel nozzle assemblies in each combustor. The nozzle is for the dual fuel option and shows the passages for diffusion gas, premixed gas, oil, and water. When mounted on the end cover, the diffusion passages of four of the fuel nozzles are fed from a common manifold, called the primary that is built into the end cover. The premixed passage of the same four nozzles is fed from another internal manifold called the secondary. The premixed passages of the remaining nozzle are supplied by the tertiary fuel system; the diffusion passage of that nozzle is always purged with compressor discharge air and passes no fuel. Figure (4.20) shows fuel nozzle assembly. Figure (4.21) shows the nozzle passage.
dc220.4shared.com/doc/u2BZFNqQ/preview.html
21/38
09/05/2012
The combustion liners Figure (4.22) use external ridges and conventional cooling slots for cooling. Interior surfaces of the liner and the cap are thermal barrier coated to reduce metal temperatures and thermal gradients. The cap has five premiers tubes that engage each of the five fuel nozzle. It is cooled by a combination of film cooling and impingement cooling and has thermal barrier coating on the inner surfaces.
dc220.4shared.com/doc/u2BZFNqQ/preview.html 22/38
09/05/2012
Combustion is initiated by means of the discharge from spark plugs which are bolted to flanges on the combustion cans and centered within the liner and flow sleeve in adjacent combustion chambers. A spark plug that is used in the power plant plug is shown in Figure (3.23). These plugs receive their energy from high energy-capacitor discharge power supplies. At the time of firing, a spark at one or more of these plugs ignites the gases in a chamber; the remaining chambers are ignited by crossfire through the tubes that interconnect the reaction zone of the remaining chambers.
dc220.4shared.com/doc/u2BZFNqQ/preview.html
23/38
09/05/2012
During the starting sequence, it is essential that an indication of the presence or absence of flame be transmitted to the control system. For this reason, a flame monitoring system is used consisting of multiple flame detectors. The flame detectors figures (4.24) have water cooled jackets to maintain acceptable temperatures. The ultraviolet flame sensor contains a gas filled detector. The gas within this detector is sensitive to the presence of ultraviolet radiation which is emitted by a hydrocarbon flame. A DC voltage, supplied by the amplifier, is impressed across the detector terminals. If flame is present, the ionization of the gas in the detector allows conduction in the circuit which activates the electronics to give an output indicating flame. Conversely, the absence of flame will generate an output indicating no flame. The signals from the four flame detectors are sent to the control system which uses an internal logic system to determine whether a flame or loss of flame condition exists. For detailed operating and maintenance information covering this equipment, refer to the vendor publications.
dc220.4shared.com/doc/u2BZFNqQ/preview.html
24/38
09/05/2012
The cap has five pre-mixer tubes that engage each of the five fuel nozzle. It is cooled by a combination of film cooling and impingement cooling and has thermal barrier coating on the inner surfaces. This is shown in figure (4.25).
The three-stage turbine section is the area in which energy in the form of high temperature pressurized gas, produced by the compressor and combustion sections, is converted to mechanical energy. Gas turbine hardware includes the turbine rotor, turbine casing, exhaust frame, exhaust diffuser, nozzles, and shrouds. Table of main specifications of the station turbine:
Table 4.1 of main specifications of the station turbine
Type
09/05/2012
The base that supports the gas turbine is structural steel fabrication of welded steel beams. And plate its prime function is to provide a support up on which to mount the gas turbine is mounted to its base by vertical supports at three location. The forward support at the lower half-vertical flange of the forward compressor casing and the two on either side of the turbine exhaust frame.
2. Turbine Rotor
1. Structure
The turbine rotor assembly consists of the forward and turbine wheel shafts and the first, second and third stage turbine wheel assemblies with spacers and turbine buckets. Concentricity control is achieved with mating rabbets on the turbine wheels, wheel shafts, and spacers. The wheels are held together with through bolts mating up with bolting flanges on the wheel shafts and spacers. Selective positioning of rotor members is performed to minimize balance corrections.
2. Wheel Shafts
The turbine rotor distance piece extends from the first-stage turbine wheel to the flange of the compressor rotor assembly. The turbine rotor shaft includes the No. 2 bearing journal.
3. Wheel Assemblies
dc220.4shared.com/doc/u2BZFNqQ/preview.html
26/38
09/05/2012
Spacers between the first and second, and between the second and third-stage turbine wheels determine the axial position of the individual wheels. These spacers carry the diaphragm sealing lands. The 1-2 spacer forward and faces include radial slots for cooling air passages. Turbine buckets are assembled in the wheels with fir-tree-shaped dovetails that fit into matching cut-outs in the turbine wheel rims. All three turbine stages have precision investment-cast, long shank buckets. The long-shank bucket design effectively shields the wheel rims and bucket root fastenings from the high temperatures in the hot gas path while providing mechanical damping of bucket vibrations. As a further aid in vibration damping, the stage-two and stage-three buckets have interlocking shrouds at the bucket tips. These shrouds also increase the turbine efficiency by minimizing tip leakage. Radial teeth on the bucket shrouds combine with stepped surfaces on the stator to provide a labyrinth seal against gas leakage past the bucket tips. Figure (4.27) shows typical first-, second-, and third-stage turbine buckets for the MS9001FA. The increase in the size of the buckets from the first to the third stage is necessitated by the pressure Reduction resulting from energy conversion in each stage, requiring an increased annulus area to accommodate the gas flow.
Figure (4.27) shows the stages of the turbine in the power plant.
dc220.4shared.com/doc/u2BZFNqQ/preview.html
27/38
09/05/2012
4. Cooling of Turbine
The turbine rotor is cooled to maintain reasonable operating temperatures and, therefore, assure a longer turbine service life. Cooling is accomplished by means of a positive flow of cool air extracted from the compressor and discharged radialy outward through a space between the turbine wheel and the stator, into the main gas stream. This area is called the wheel space. Figure (4.28) shows the turbine cooling air flows.
09/05/2012
The first-stage forward wheel space is cooled by compressor discharge air. A labyrinth seal is installed at the end of the compressor rotor between the rotor and inner barrel of the compressor discharge casing. The leakage through this labyrinth furnishes the air flow through the first-stage forward wheel space. This cooling air flow discharges into the main gas stream of the first-stage nozzle. The first-stage wheel space is cooled by 13th stage extraction air ported through the 2nd stage nozzle. This air returns to the gas path forward of the 2nd stage nozzle.
The second-stage forward wheel space is cooled by leakage from the first-stage wheel space through the interstate labyrinth. This air returns to the gas path at the entrance of the second-stage buckets. The second-stage wheel space is cooled by 13th stage extraction air ported through the 3rd Stage nozzle.
7. Third-Stage Wheel spaces
dc220.4shared.com/doc/u2BZFNqQ/preview.html 29/38
09/05/2012
The third-stage forward wheel space is cooled by leakage from the second-stage wheel space through the interstate labyrinth. This air reenters the gas path at the third-stage bucket entrance. The third-stage wheel space obtains its cooling air from the discharge of the exhaust frame cooling air annulus. This air flows through the third-stage wheel space and into the gas pat at the entrance to the exhaust diffuser.
8. Buckets
Air is introduced into each first-stage bucket through a plenum at the base of the bucket dovetail as shown in Figure (4.30). It flows through serpentine cooling holes extending the length of the bucket and exits at the trailing edge and the bucket tip. The holes are spaced and sized to obtain optimum cooling of the airfoil with minimum compressor extraction air Figure (4.30) shows the MS9001FA first-stage bucket design unlike the first-stage buckets, the second-stage buckets are cooled by span wise air passages the length of the airfoil. Air is introduced like the first-stage, with a plenum at the base of the bucket dovetail. The thirdstage buckets are not internally air cooled; the tips of these buckets, like the second stage buckets, are enclosed by a shroud which is a part of the tip seal. These shrouds interlock from bucket to bucket to provide vibration damping.
dc220.4shared.com/doc/u2BZFNqQ/preview.html
30/38
09/05/2012
1. Structure
The turbine casing and the exhaust frame constitute the major portion of the turbine gas turbine stator structure. The turbine nozzles, shrouds, and turbine exhaust diffuser are internally supported from these components.
2. Turbine Casing
The turbine casing controls the axial and radial positions of the shrouds and nozzles. It determines turbine clearances and the relative positions of the nozzles to the turbine buckets. This positioning is critical to gas turbine performance. Hot gases contained by the turbine casing are a source of heat flow into the casing. To control the casing diameter, it is important to reduce the heat flow into the casing and to limit its temperature. Heat flow limitations incorporate insulation, cooling, and multi-layered structures. 13th stage extraction air is piped into the turbine casing annular spaces around the 2nd and 3rd stage nozzles. From there the air is ported through the nozzle partitions and into the wheel spaces. Structurally, the turbine casing forward flange is bolted to the bulkhead flange at the end of the compressor discharge casing. The turbine casing flange is bolted to the forward flange
dc220.4shared.com/doc/u2BZFNqQ/preview.html 31/38
09/05/2012
In the turbine section there are three stages of stationary nozzles which direct the highvelocity flow of the expanded hot combustion gas against the turbine buckets causing the turbine rotor to rotate. Because of the high pressure drop across these nozzles, there are seals at both the inside and the outside diameters to prevent loss of system energy by leakage. Since these Nozzles operate in the hot combustion gas flow; they are subjected to thermal stresses in addition to gas pressure loadings.
First-Stage Nozzle
The first-stage nozzle receives the hot combustion gases from the combustion system via the transition pieces. The transition pieces are sealed to both the outer and inner sidewalls on the entrance side of the nozzle; this minimizes leakage of compressor discharge air into the nozzles. The Model 6001B gas turbine first-stage nozzle contains a forward and cavity in the vane and is cooled by a combination of film, impingement and convection techniques in both the vane and sidewall regions. The nozzle segments, each with two partitions or airfoils, are contained by a horizontally split retaining ring which is centerline supported to the turbine casing on lugs at the sides and guided by pins at the top and bottom vertical centerlines. This permits radial growth of the retaining ring, resulting from changes in temperature, while the ring remains centered in the casing. The outer diameter of the retaining ring is loaded against the forward face of the first-stage turbine shroud and acts as the air seal to prevent leakage of compressor discharge air between the nozzle and turbine casing. On the inner sidewall, the nozzle is sealed by a flange cast on the inner diameter of the sidewall that rests against a mating face on the first-stage nozzle support ring. Circumferential rotation of the segment inner sidewall is prevented by an eccentric bushing and a locating dowel that engages a lug on the inner sidewall. The nozzle is prevented from moving forward by the lugs welded to the outside diameter of the retaining ring at 45 degrees from vertical and horizontal centerlines. These lugs fit in groove machined in the turbine shell just forward of the first-stage shroud T hook. By moving the horizontal joint support block and the bottom centerline guide pin and then removing the inner sidewall locating dowels, the lower half of the nozzle can be rolled out with the turbine rotor in
dc220.4shared.com/doc/u2BZFNqQ/preview.html 32/38
09/05/2012
place.
Second-Stage Nozzle
Combustion air exiting from the first stage buckets is again expanded and redirected against the second- stage turbine buckets by the second-stage nozzle. This nozzle is made of cast segments, each with two partitions or airfoils. The male hooks on the entrance and exit sides of the outer sidewall fit into female grooves on the side of the first-stage shrouds and on the forward side of the second-stage shrouds to maintain the nozzle concentric with the turbine shell and rotor. This close fitting tongue-and-groove fit between nozzle and shrouds acts as an outside diameter air seal. The nozzle segments are held in a circumferential position by radial pins from the shell into axial slots in the nozzle outer sidewall. The second-stage nozzle is cooled with 13th stage extraction air.
4. Diaphragms
Attached to the inside diameters of both the second and third-stage nozzle segments are the nozzle diaphragms. These diaphragms prevent air leakage past the inner sidewall of the nozzle and the turbine rotor. The high/low, labyrinth seal teeth are machined into the inside diameter of the diaphragm. They mate with opposing sealing lands on the turbine rotor. Minimal radial clearance between stationary parts (diaphragm and nozzles) and the moving rotor are essential for maintaining low inter stage leakage, these results in higher turbine efficiency.
5. Shrouds
Unlike the compressor bleeding, the turbine bucket tips not run directly against an integral machined surface of the casing but against annular curved segments called turbine shrouds. The shrouds primary function is to provide a cylindrical surface for minimizing bucket tip clearance leakage.
dc220.4shared.com/doc/u2BZFNqQ/preview.html
33/38
09/05/2012
The exhaust frame is bolted to the flange of the turbine casing. Structurally, the frame consists of an outer cylinder and an inner cylinder interconnected by the radial struts. The No. 2 bearing is supported from the inner cylinder. The exhaust diffuser located at the after end of the turbine is bolted to the exhaust frame. Gases exhausted from the third turbine stage enter the diffuser where velocity is reduced by diffusion and pressure is recovered. At the exit of the diffuser, the gases are directed into the exhaust plenum. Exhaust frame radial struts cross the exhaust gas stream. These struts position the inner cylinder and No. 2 bearing in relation to the outer casing of the gas turbine. The struts must be maintained at a constant temperature in order to control the center position of the rotor in relation to the stator. This temperature stabilization is accomplished by protecting the struts fro fairing that forms an air space around each strut and provides a rotated, combined airfoil shape. Off through the space between the struts and the wrapper to maintain uniform temperature of the struts. This air is then directed to the third wheel space. Trunnions on the sides of the exhaust frame are used with similar trunnions on the forward compressor casing to lift the gas turbine when it is separated from its base Figure (4.32) shows the exhaust duct which included silencers and a flange of the turbine casing.
4.3.6.1 Silencers
The disclosed silencer has noise gas duct in parallel with but with as to define gas passage
dc220.4shared.com/doc/u2BZFNqQ/preview.html 34/38
09/05/2012
means and noise duct. The noise-absorbing space means is closed by noise at inlet and outlet ends of the duct. A plurality of gas chambers aligned along the line of gas flow through the duct are formed in said noise absorbing space means by disposing noise therein as shown in Figure (4.33) Silencers noise-absorbing partitions disposed in a spacing from outer walls of the duct, so noise-absorbing space means in the noising noise-shielding sectional walls Figure (4.33) -shielding plates noise-shielding.
4.4 StartUp
Startup control brings the gas turbine from zero speed up to operating speed safely by providing proper fuel to establish flame, accelerate the turbine, and to do it in such a manner as to minimize the low cycle fatigue of the hot gas path parts during the sequence. This involves proper sequencing of command signals to the accessories, starting device and fuel control system. Since a safe and successful startup depends on proper functioning of the gas turbine equipment, it is important to verify the state of selected devices in the sequence. Much of the control logic circuitry is associated not only with actuating control devices, but enabling protective circuits and obtaining permissive conditions before proceeding. The gas turbine uses a static start system whereby the generator serves as a starting motor. A turning gear is used for rotor breakaway. General values for control settings are given in this description to help in the understanding of the operating system. Actual values for control settings are given in the Control Specifications for a particular machine.
dc220.4shared.com/doc/u2BZFNqQ/preview.html
35/38
09/05/2012
An important part of the startup/shutdown sequence control of the gas turbine is proper speed sensing. Turbine speed is measured by magnetic pickups and will be discussed under speed control. The following speed detectors and speed relays are typically used:
1. L14HR ZeroSpeed (approx. 0% speed). 2. L14HM Minimum Speed (approx. 16% speeds). 3. L14HA Accelerating Speed (approx. 50% speeds). 4. L14HS Operating Speed (approx. 95% speeds).
The zerospeed detector, L14HR, provides the signal when the turbine shaft starts or stops rotating. When the shaft speed is blown 14HR, or at zerospeed, L14HR picksup (fail safe) and the permissive logic initiates turning gear or slowroll operation during the automatic startup sequence of the turbine. The minimum speed detector L14HM indicates that the turbine has reached the minimum firing speed and initiates the purge cycle prior to the introduction of fuel and ignition. The dropout of the L14HM minimum speed relay provides several permissive functions in the restarting of the gas turbine after shutdown. The accelerating speed relay L14HA pickup indicates when the turbine has reached approximately 50 percent speeds; this indicates that turbine startup is progressing and keys certain protective features. The highspeed sensor L14HS pickup indicates when the turbine is at speed and that the accelerating sequence is almost complete. This signal provides the logic for various control sequences such as stopping auxiliary lube oil pumps and starting turbine shell/exhaust frame blowers. The turbine and generator should slow during an under-frequency situation; L14HS will drop out at the underfrequency speed setting. After L14HS drops out the generator breaker will trip open and the Turbine Speed Reference (TNR) will be reset to 100.3%. As the turbine accelerates, L14HS will again pick up; the turbine will then require another start signal before the generator will attempt to autosynchronize to the system again. The actual settings of the speed relays are listed in the Control Specification and are programmed in the <RST> processors as EEPROM control constants.
dc220.4shared.com/doc/u2BZFNqQ/preview.html
36/38
09/05/2012
The startup control operates as an open loop control using preset levels of the fuel command signal FSR. The levels are: ZERO, FIRE, WARMUP, ACCELERATE and MAX. The Control Specifications provide proper settings calculated for the fuel anticipated at the site. The FSR levels are set as Control Constants in the SPEEDTRONIC Mark VI startup control. Startup control FSR signals operate through the minimum value gate to ensure that other control functions can limit FSR as required. The fuel command signals are generated by the SPEEDTRONIC control startup software. In addition to the three active startup levels, the software sets maximum and minimum FSR and provides for manual control of FSR. Clicking on the targets for MAN FSR CONTROL and FSR GAG RAISE OR LOWER allows manual adjustment of FSR setting between FSRMIN and FSRMAX. While the turbine is at rest, electronic checks are made of the fuel system stop and control valves, the accessories, and the voltage supplies
When the turbine breaks away the turning gear .it will rotate the turbine rotor from 5 to 7 rpm. As the static starter begins its sequence, and accelerates the rotor the starting clutch will automatically disengage the turning gear from the turbine rotor. The turbine speed relay L14HM indicates that the turbine is turning at the speed required for proper purging and ignition in the combustors. Gas fired units that have exhaust configurations which can trap gas leakage (i.e., boilers) have a purge timer, L2TV, which is initiated with the L14HM signal. The purge time is set to allow three to four changes of air through the unit to ensure that any combustible mixture has been purged from the system. The starting means will hold
dc220.4shared.com/doc/u2BZFNqQ/preview.html 37/38
09/05/2012
speed until L2TV has completed its cycle. Units which do not have extensive exhaust systems may not have a purge timer, but rely on the starting cycle and natural draft to purge the system.
49
dc220.4shared.com/doc/u2BZFNqQ/preview.html
38/38