Service Manual: XS-G3 XS-G4 XS-G5

XS-G3
XS-G4
XS-G5
U,LH,EZ,K
EZ
EZ,K
SERVICE MANUAL
COMPACT DISC
STEREO SYSTEM
BASIC TAPE MECHANISM : BZM-1 R1NM

BASIC CD MECHANISM : BZG-5 ZD3NM
SYSTEM
CD
CASSEIVER
SPEAKER
REMOTE
CONTROLLER
XSG3(U,LH)
CXG3
SXG3
RCBAS11
XSG3(EZ,K)
CXG3
SXG3
RCBAS03
XSG4(EZ)
CXG4
SXG4
RCBAS11
XSG5(EZ)
CXG5
SXG5
RCBAS11
XSG5(K)
CXG5
SXG5
RCBAS03
This Service Manual is the "Revision Publishing" and replaces "Simple Manual"
XS-G3 (U,LH,EZ,K) / XS-G4 (EZ) / XS-G5 (EZ,K), (S/M Code No. 09-012-441-5T1).
S/M Code No. 09-013-441-5R1
RE
VI
SIO
DA
N
TA
If requiring information about the CD mechanisim, see Service Manual of BZG-5,

(S/M Code No. 09-00C-353-3N2)
SPECIFICATIONS
<FM tuner section>
Tuning range
Usable sensitivity (IHF)
Antenna terminal
<AM/MW tuner section>
Tuning range
87.5 MHz to 108 MHz

EZ,K: 16.8 dBf
U,LH: 13.2 dBf
75 ohms (unbalanced)
Usable sensitivity
Antenna
531 kHz to 1602 kHz (9 kHz step)

530 kHz to 1710 kHz (10 kHz step)
350 V/m
Loop antenna
<LW tuner section><EZ,K>

Tuning range
Usable sensitivity
Antenna
144 kHz to 290 kHz

1400 V/m
Loop antenna
<Amplifier section>
Power output
Total harmonic distortion
Inputs
Output
EZ,K:
Rated: 40 W + 40 W (6 ohms,
T.H.D. 1 %, 1 kHz/DIN45500)
Reference: 50 W + 50 W (6 ohms,
T.H.D. 10 %, 1 kHz/DIN45324)
EZ:
DIN MUSIC POWER: 121 W + 121 W
U: 60 W + 60 W (50 Hz 20 kHz,
T.H.D. less than 1 %, 6 ohms)
75 W + 75 W (1 kHz, T.H.D. less than
10 %, 6 ohms)
LH:
Rated: 60 W + 60 W (6 ohms,
T.H.D. 1 %, 1 kHz)
Reference: 75 W + 75 W (6 ohms,
T.H.D. 10 %, 1 kHz)
EZ,K:
0.08 % (25 W, 1 kHz, 6 ohms, DIN
AUDIO)
U,LH:
0.08 % (30 W, 1 kHz, 6 ohms, DIN
AUDIO)
VIDEO/AUX: 500 mV
LH ONLY: MIC: 1.7mV (10 kohms)
SPEAKERS: 6 ohms or more
PHONES: 32 ohms or more
<Compact disc player section>

Laser
Semiconductor laser ( =780 nm)
D/A converter
1 bit dual
Signal-to-noise ratio
85 dB (1 kHz, 0 dB)
Harmonic distortion
0.05 % (1 kHz, 0 dB)
<Speaker system SXG3 / SXG4>
Speaker system
2 way, bass reflex (magnetic shielded)
Speaker units
Woofer: 140 mm cone
Tweeter: 60 mm cone
Impedance
6 ohms
Dimensions (W x H x D)
165 x 328 x 225 mm
Weight
3.5 kg
<Speaker system SXG5>
Speaker system
Speaker units
Impedance
Weight
<General>
Power requirements
Power consumption
Power consumption
in standby mode
Dimensions of main unit
(W x H x D)
Weight
2 way, bass reflex (magnetic shielded)

Woofer: 140 mm cone
Tweeter: 60 mm cone
6 ohms
170 x 328 x 268 mm
3.8 kg
EZ,K: 230 V AC, 50 Hz

U: 120 V AC, 60 Hz
LH: 120 V / 220 230 V / 240 VAC
(Switchable), 50 Hz / 60 Hz
U: 65 W
LH: 85 W
EZ: 70 W
K: 78 W
With ECO mode on: 0.6 W
U,EZ,K: With ECO mode off: 17 W
LH: With ECO mode off: 18 W
U,EZ,K: 260 x 271.5 x 355 mm
(101/4 x 103/4 x 14 in.)
LH: 260 x 271.5 x 364 mm
260 x 301 x 292 mm
U,EZ,K: 6.5 kg (14 lbs 5 oz)
LH: 6.8 kg
Design and specifications are subject to change without notice.

<Cassette deck section>
Track format
Frequency response
Recording system
Heads
4 tracks, 2 channels stereo

50 Hz 15000 Hz
AC bias
Recording/playback x 1, erase x 1
The word "BBE"and the "BBE symbol" are trademarks of BBE

Sound, Inc.
Under license from BBE Sound,Inc.
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING

This set employs laser. Therefore, be sure to follow carefully
the instructions below when servicing.
WARNING!!
WHEN SERVICING, DO NOT APPROACH THE LASER
EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS
NECESSARY TO CONFIRM LASER BEAM EMISSION.
BE SURE TO OBSERVE FROM A DISTANCE OF MORE
THAN 30cm FROM THE SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK.
CAUTION
Use of controls or adjustments or performance of procedures other than those specified herin may result in
hazardous radiation exposure.
ATTENTION
Lutillisation de commandes, rglages ou procdures
autres que ceux spcifis peut entraner une dangereuse
exposition aux radiations.
ADVARSEL
s
Caution: Invisible laser radiation when

open and interlocks defeated avoid
exposure to beam.
Advarsel: Usynlig laserstling ved bning,
nr sikkerhedsafbrydere er ude af funktion.
Undg udsttelse for strling.
Usynlig laserstling ved bning, nr sikkerhedsafbrydereer

ude af funktion. Undg udsttelse for strling.
This Compact Disc player is classified as a CLASS 1
LASER product.
The CLASS 1 LASER PRODUCT label is located on the
rear exterior.
VAROITUS!
Laiteen Kyttminen muulla kuin tss kyttohjeessa
mainitulla tavalla saataa altistaa kyt-tjn
turvallisuusluokan 1 ylittvlle nkymttmlle
lasersteilylle.
CLASS 1
KLASSE 1
LUOKAN 1
KLASS 1
VARNING!
Om apparaten anvnds p annat stt n vad som
specificeras i denna bruksanvising, kan anvndaren
utsttas fr osynling laserstrlning, som verskrider
grnsen fr laserklass 1.
LASER PRODUCT
LASER PRODUKT
LASER LAITE
LASER APPARAT
Precaution to replace Optical block

PICK-UP Assy PWB
(KSS-213F)
Body or clothes electrostatic potential could
ruin laser diode in the optical block. Be sure
ground body and workbench, and use care the
clothes do not touch the diode.
1) After the connection, remove solder shown in

right figure.
Solder
NOTE ON BEFORE STARTING REPAIR

1. Forced discharge of electrolytic capacitor of power supply block
When repair is going to be attempted in the set that uses relay circuit in the power supply block, electric potential is kept charged across
the electrolytic capacitors (C101, 102) even though AC power cord is removed. If repair is attempted in this condition, secondary defect
can occur.
In order to prevent the secondary trouble, perform the following measures before starting repair work.
Discharge procedure
MAIN C.B
1 Remove the AC power cord.

2 Connect a discharging resistor at an end of lead wire that
has clips at both ends. Connect the other end of the lead
wire to metal chassis.
3 Contact the other end of the discharging resistor to the
positive (+) side (+VH) of C101. (For two seconds)
4 Contact the same end of the discharging resistor as step
3 to the negative (-) side (-VH) of C102 in the same way.
(For two seconds)
5 Check that voltage across C101 and C102 has decreased
to 1 V or less using a multimeter or an oscilloscope.
D101
Select a discharging resistor referring to the following table.
C102
Fig-1
Charging voltage (V)
Discharging
(C101, 102)
resistor ()
25-48
100
87-A00-247-090
49-140
220
87-A00-232-090
Rated power (W)
C101
Parts number
Note: The reference numbers (C101, C102) of the electrolytic capacitors can change depending on the models. Be sure to check the
reference numbers of the charging capacitors on schematic diagram before starting the discharging work.
2. Check items before exchanging the MICROCOMPUTER

Be sure to check the following items before exchanging the MICROCOMPUTER. Exchange the MICROCOMPUTER after confirming
that the MICROCOMPUTER is surely defective.
2-1. Regarding the HOLD terminal of the MICROCOMPUTER

When the HOLD terminal (INPUT) of the MICROCOMPUTER is H, the MICROCOMPUTER is judged to be operating correctly.
When this terminal is L, the main power cannot be turned on. Therefore, be sure to check the terminal voltage of the HOLD
terminal before exchange.
When the MICROCOMPUTER is not defective, the HOLD terminal can also go L when the POWER AMPLIFIER has any
abnormalities that triggers the abnormality detection circuit on the MAIN C. B. that sets the HOLD terminal to L.
Good or no good judgement of the MICROCOMPUTER

1 Turn on the AC main power.
2 Confirm that the main power is turned on and the HOLD terminal of the MICROCOMPUTER keeps the H level or not.
3 When the HOLD terminal is L level, the abnormality detection circuit is judged to be working correctly and the
MICROCOMPUTER is judged to be good.
In such a case, check also if the POWER AMPLIFIER circuit or power supply circuit has any abnormalities or not.
2-2. Regarding reset
TE
R
There are cases that the machine does not work correctly because the MICROCOMPUTER is not reset even though the AC power
cord is re-inserted, or the software reset (pressing the STOP key + POWER key) is performed.
When the above described phenomenon occurs, it can lead to wrong judgement as if the MICROCOMPUTER is defective and to
exchange the MICROCOMPUTER. In such a case, perform the forced-reset by the following procedure and check good or no
good of the MICROCOMPUTER.
1 Remove the AC power cord.
IC
RO
CO
PU
FRONT C.B
18
15
C113
% VSS
MICROC113
COMPUTER
* VDD
FRONT C.B
Short with tweezers.
Fig-2-2
2 Short both ends of the electrolytic capacitor C113 that is connected to VDD of the MICROCOMPUTER with tweezers.
3 Connect the AC power cord again. If the MICROCOMPUTER returns to the normal operation, the MICROCOMPUTER is
good.
Note: The reference number or MICROCOMPUTER pin number of transistor (Q110) and electrolytic capacitor (C113) can change depending
on the models. Be sure to check the reference numbers on schematic diagram before starting the discharging work.
2-3. Confirmation of soldering state of MICROCOMPUTER

Check the soldering state of the MICROCOMPUTER in addition to the above described procedures. Be sure to exchange the
MICROCOMPUTER after surely confirming that the trouble is not caused by poor soldering but the MICROCOMPUTER itself.
DISASSEMBLY INSTRUCTIONS
1. DISASSEMBLY OF MECHANISM DECK ASSY
1) Remove the three screws.
2) Remove the three screws.
3) Remove the four screws (1) and remove the PANEL,

TOP (2).
4) Remove the PANEL, RIGHT.
5) Remove the PANEL, LEFT.
6) Remove the six screws (1) and remove the CABI, REAR
(2).
7) Remove the three FFCs (1), (2) (black) and (3), and
remove the connector (4).
8) Remove the three screws (1) and remove the PWB,

MAIN (2).
9) Slide up slightly the WINDOW, DISP ASSY (1).

Insert a thin flathead screwdriver into the slide groove
and disengage the detents of the WINDOW, DISP ASSY
(2) (in the left and right sides) and remove the WINDOW,
DISP ASSY.
10) Remove the two FFCs (1) and (2), and the four screws
(3) and remove the MECH DECK ASSSY (4).
11) Remove the two screws (1) and remove the HLDR,
WINDOW (2).
12) Remove the four screws (1) and remove the BZM-1 (2).
2. INSTRUCTIONS FOR ASSEMBLING MECHANISM

DECK ASSY
1) Install the BZM-1 and rotate the GEAR, RELAY
clockwise until the BOX, CASS cannot move any more.
2) Install the HLDR, WINDOW so that the upper end of the

HLDR, WINDOW and the upper end of the MECH ASSY
can be almost aligned to the same height.
3) Rotate the GEAR, RELAY until the HLDR, WINDOW

goes to the lowest part and stops.
10
PHASES ALIGNMENT
a
3) Mount GEAR, RELAY WINDOW
to put together b and c.
GEAR RELAY
* Mount in order.
1), 2), 3).
Join
c
GEAR, RELAY WINDOW
2) APPLY GREASE
(FG-87H)
BOTH SIDE of
the RIB.
*Align the position "b"
with position "c".
a, b STEP
1mm
1) Turn GEAR RELAY until.

This LEVER is stopped.
(SEE a)
APPLY CFD-409 on the RAIL

(From top to BOTTOM)
a
HDR,MECHA ASSY
2) Engage the gear so that the HDLR.

MECH ASSY comes to the same
height as the top (0 portion) of HLDR.
WINDOW.
JOIN with
RACK
HLDR, WINDOW
b
1) Rotate the GEAR RELAY to open

the DECK.
Rotate it until it can rotate no more.
11
ELECTRICAL MAIN PARTS LIST
REF. NO. PART NO.
KANRI
NO.
DESCRIPTION
IC
8B-NF8-645-010
8B-NF8-646-010
87-A21-831-010
87-A21-419-040
87-A21-893-040
C-IC,LC877256A-5V18<LH,U,K,3EZ>
C-IC,LC877264V-5V24<4EZ,5EZ>
IC,SPS-422-1-F1
C-IC,NJM14558MD-TE2
C-IC,NJM4558V-TE2
87-A21-401-040
87-070-289-040
87-A21-695-010
87-A20-440-040
87-A21-928-010
C-IC,M61503FP
IC,BU2092F
IC,LA1845L
C-IC,BU1920FS<5EZ,4EZ>
IC,LC72131D-N
87-020-454-010
IC,DN6851
87-A30-559-010
87-A30-492-080
87-A30-076-080
87-A30-075-080
87-A30-494-080
TR,CSB1370EF
TR,2SC5343G
C-TR,2SC3052F
C-TR,2SA1235F
TR,2SA1980G
87-A30-107-070
87-A30-484-080
87-A30-190-080
87-A30-106-040
87-A30-306-010
C-TR,CMBT5401
C-TR,KRA102S
TR,CC5551
C-TR,CMBT5551
TR,2SB1677<EZ,K>
87-A30-528-010
87-A30-307-010
87-A30-529-010
87-A30-490-080
87-A30-162-010
TR,2SB1686<LH,U>
TR,2SD2619<EZ,K>
TR,2SD2642<LH,U>
C-TR,KRC107S
FET,2SK2937
87-A30-582-080
87-A30-495-080
87-A30-468-080
87-A30-091-080
87-A30-062-080
TR,CDA1585BC
TR,2SA1981Y
C-TR,KRC102S-RTK
FET,2SJ460
C-TR,KRC104S
87-A30-063-080
87-A30-520-080
87-A30-515-080
87-A30-087-080
87-A30-090-080
C-TR,KRA104S
TR,2SC5342Y
TR,2SA1979O/Y
C-FET,2SK2158
FET,2SK2541
89-327-143-080
87-A30-489-080
89-503-602-080
87-A30-086-040
87-A30-234-080
C-TR,2SC2714O
C-TR,KRA107S
C-FET,2SK360E
C-TR,CSD1306E<EZ,K>
TR,CSC4115BC
REF. NO. PART NO.
KANRI
DESCRIPTION
NO.
CHIP CAPACITOR,0.1-25<LH>
C-CAP,U, 0.1-25F<U,EZ,K>
C9
C10
C10
C11
C11
87-010-196-080
87-010-759-080
87-010-196-080
87-010-759-080
87-010-196-080
C12
C12
C19
C19
C19
87-010-759-080
87-010-196-080
87-A12-776-090
87-A12-382-000
87-A12-779-090
CAP,E 2200-50 M 85 SKR<EZ,K>
CAP,E 2200-63 M 85 IV LELON<LH,U>
CAP,E 3300-50 M 85 KR<EZ>
C20
C20
C20
C21
C21
87-A12-776-090
87-A12-779-090
87-A12-382-000
87-A12-777-090
87-A12-782-090
CAP,E
CAP,E
CAP,E
CAP,E
CAP,E
C21
C22
C22
C32
C32
87-A12-778-090
87-A12-777-090
87-A12-778-090
87-010-197-080
87-012-286-080
CAP,E 3300-35 M 85 SKR<LH,U>

CAP,E 3300-25 M 85 SKR<EZ,K>
CAP,E 3300-35 M 85 SKR<LH,U>
CAP, CHIP 0.01 DM<LH>
CAP, U 0.01-25<U,EZ,K>
C33
C34
C35
C35
C36
87-A12-062-080
87-A12-072-080
87-A12-071-080
87-A12-090-080
87-A12-066-080
CAP,E
CAP,E
CAP,E
CAP,E
CAP,E
C36
C38
C38
C60
C61
87-A12-067-080
87-010-197-080
87-012-286-080
87-A12-089-080
87-A12-071-080
CAP,E 330-16 SMG<LH,U,K>

CAP, CHIP 0.01 DM<LH>
CAP, U 0.01-25<U,EZ,K>
CAP,E 3.3-50 SMG
CAP,E 47-25 SMG
C83
C97
C101
C102
C103
87-A12-074-080
87-010-831-080
87-012-279-080
87-012-279-080
87-A12-084-080
CAP,E 470-25 SMG

C-CAP,U,0.1-16F
C-CAP,U 2700P-50 B
C-CAP,U 2700P-50 B
CAP,E 0.22-50 SMG
C104
C105
C106
C107
C108
87-A12-084-080
87-012-277-080
87-012-277-080
87-A12-089-080
87-A12-089-080
CAP,E 0.22-50 SMG

C-CAP, U 1800P-50 B
C-CAP, U 1800P-50 B<LH,U,K>
CAP,E 3.3-50 SMG
CAP,E 3.3-50 SMG
C109
C110
C111
C112
C113
87-012-195-080
87-012-195-080
87-A12-077-080
87-A12-077-080
87-A10-596-080
C-CAP,U 100P-50CH<EZ,K>
CAP,E 33-35 SMG
CAP,E 33-35 SMG
C-CAP,S 100P-100 J CH
C114
C117
C118
C119
C120
87-A10-596-080
87-012-368-080
87-012-368-080
87-012-286-080
87-012-286-080
C-CAP,S 0.1-50 F
C-CAP,S 0.1-50 F
CAP, U 0.01-25
CAP, U 0.01-25
C123
C124
C133
C140
C186
87-010-177-080
87-010-177-080
87-012-282-080
87-012-278-080
87-010-759-080
C-CAP,S 820P-50 SL
C-CAP,S 820P-50 SL
CAP, U 4700P-50
C-CAP,U 2200P-50 B
C-CAP,U, 0.1-25F
C187
C188
C225
C226
C227
87-A12-091-080
87-A12-091-080
87-012-368-080
87-012-368-080
87-012-368-080
CAP,E 10-50 SMG

CAP,E 10-50 SMG
C-CAP,S 0.1-50 F
C-CAP,S 0.1-50 F
C-CAP,S 0.1-50 F
C228
C229
C230
C231
C232
87-012-368-080
87-010-191-080
87-010-191-080
87-012-286-080
87-012-286-080
C-CAP,S 0.1-50 F
C-CAP,S 0.015-50 F<EZ,K>
C-CAP,S 0.015-50 F<EZ,K>
CAP, U 0.01-25<EZ,K>
CAP, U 0.01-25<EZ,K>
C303
C304
C307
C308
C309
87-012-275-080
87-012-275-080
87-A12-062-080
87-A12-062-080
87-012-188-080
C-CAP,U 1200P-50 B
C-CAP,U 1200P-50 B
CAP,E 100-10 SMG
CAP,E 100-10 SMG
C-CAP,U 47P-50 CH
2200-50
3300-50
2200-63
3300-25
4700-25
M
M
M
M
M
85
85
85
85
85
SKR<K>
KR<EZ>
IV LELON<LH,U>
SKR<K>
SKR<EZ>
TRANSISTOR
DIODE
87-A40-393-090
87-A40-291-080
87-A40-455-090
87-A40-764-080
87-A40-553-080
DIODE,1N5402GW(F20)
DIODE,1N4148M(CPT)
DIODE,RL203 GW<EZ,K>
ZENER,UZ10BSC
DIODE,1N4003 LES
87-A40-270-080
87-A40-269-080
87-A40-488-080
87-A40-748-080
87-A40-002-080
C-DIODE,MC2838
C-DIODE,MC2836
DIODE,1SS244<LH>
ZENER,UZ5.6BSA
ZENER,MTZJ5.1C<U,EZ,K>
87-A40-747-080
87-A40-749-080
87-A40-739-080
87-017-149-080
ZENER,UZ5.1BSB<LH>
ZENER,UZ5.6BSB
ZENER,UZ2.7BSA
ZENER,HZS6A2L
87-012-368-080
87-012-368-080
87-012-368-080
87-012-368-080
87-010-759-080
C-CAP,S 0.1-50 F
C-CAP,S 0.1-50 F
C-CAP,S 0.1-50 F
C-CAP,S 0.1-50 F
MAIN C.B
C3
C4
C5
C6
C9
12
100-10 SMG
100-25 SMG
47-25 SMG<LH,U,K>
4.7-50 SMG<EZ>
47-16 SMG<EZ>
REF. NO. PART NO.
KANRI
DESCRIPTION
NO.
C-CAP,U 47P-50 CH
CAP, U 6800P-50
CAP, U 6800P-50
CAP,E 100-10 SMG
CAP,E 0.33-50 SMG
REF. NO. PART NO.
KANRI
NO.
CAP,
CAP,
CAP,
CAP,
CAP,
DESCRIPTION
C782
C783
C784
C785
C786
87-012-286-080
87-012-286-080
87-012-286-080
87-012-286-080
87-012-286-080
CAP,E 0.33-50 SMG

CAP, U 0.022-25
C-CAP,U,0.1-16F
CAP, U 0.01-25<EZ,K>
CAP,E 1-50 SMG
C788
C789
C789
C790
C790
87-012-167-080
87-A12-052-080
87-016-118-080
87-A12-052-080
87-016-118-080
C-CAP,U 5P-50 CH
C-CAP,S 0.033-25 J B<LH,U>
C-CAP,U0.022-25BJ<EZ,K>
C-CAP,S 0.033-25 J B<LH,U>
C-CAP,U0.022-25BJ<EZ,K>
87-A10-039-080
87-012-140-080
87-A12-083-080
87-A12-083-080
87-012-193-080
C-CAP,U 470P-50 J CH<U,EZ,K>

CAP 470P<LH>
CAP,E 0.1-50 SMG
CAP,E 0.1-50 SMG
C-CAP,U 82P-50 CH
C791
C792
C793
C795
C796
87-010-831-080
87-012-286-080
87-A12-090-080
87-012-286-080
87-012-286-080
C-CAP,U,0.1-16F
CAP, U 0.01-25
CAP,E 4.7-50 SMG
CAP, U 0.01-25
CAP, U 0.01-25
C404
C405
C406
C407
C408
87-012-193-080
87-012-286-080
87-012-286-080
87-012-286-080
87-012-286-080
C-CAP,U 82P-50 CH
CAP, U 0.01-25
CAP, U 0.01-25
CAP, U 0.01-25
CAP, U 0.01-25
C797
C798
C799
C800
C801
87-A12-091-080
87-012-286-080
87-010-265-080
87-010-829-080
87-A12-089-080
CAP,E 10-50 SMG

CAP, U 0.01-25
CAP, ELECT 33-16V
CAP, U 0.047-16
CAP,E 3.3-50 SMG
C409
C410
C411
C412
C452
87-012-278-080
87-012-278-080
87-A12-091-080
87-A12-091-080
87-A12-069-080
C-CAP,U 2200P-50 B
C-CAP,U 2200P-50 B
CAP,E 10-50 SMG
CAP,E 10-50 SMG
CAP,E 22-25 SMG
C802
C803
C804
C807
C808
87-010-829-080
87-010-787-080
87-A12-062-080
87-A12-086-080
87-A12-087-080
CAP, U 0.047-16
CAP, U 0.022-25
CAP,E 100-10 SMG
CAP,E 0.47-50 SMG
CAP,E 1-50 SMG
C453
C454
C455
C456
C457
87-012-279-080
87-012-279-080
87-012-279-080
87-012-286-080
87-A12-361-080
C-CAP,U 2700P-50 B
C-CAP,U 2700P-50 B
C-CAP,U 2700P-50 B
CAP, U 0.01-25
CAP,M 5600P-100 J CP
C809
C810
C814
C815
C816
87-A12-087-080
87-010-831-080
87-012-286-080
87-A12-086-080
87-A12-086-080
CAP,E 1-50 SMG

C-CAP,U,0.1-16F
CAP, U 0.01-25
CAP,E 0.47-50 SMG
CAP,E 0.47-50 SMG
C458
C459
C460
C461
C462
87-012-274-080
87-012-271-080
87-010-831-080
87-012-158-080
87-012-158-080
CHIP CAP,U 1000P-50B

CAP, U 560P-50
C-CAP,U,0.1-16F
C-CAP,S 390P-50 CH
C-CAP,S 390P-50 CH
C818
C821
C823
C823
C824
87-012-276-080
87-A12-091-080
87-010-177-080
87-A10-915-080
87-A12-090-080
CAP, CHIP SS 1500 PBK<EZ,K>

CAP,E 10-50 SMG
C-CAP,S 820P-50 SL<LH,U>
C-CAP,U 1000P-25 J CH<EZ,K>
CAP,E 4.7-50 SMG
C470
C605
C606
C609
C610
87-018-127-080
87-012-280-080
87-012-280-080
87-010-785-080
87-010-785-080
CAP, CER 470P-50V

CAP, U 3300P-50
CAP, U 3300P-50
C-CAP,U0.015-25BK
C-CAP,U0.015-25BK
C825
C831
C842
C844
C850
87-010-596-080
87-A12-092-080
87-012-286-080
87-012-286-080
87-A12-071-080
CAP, S 0.047-16
CAP,E 22-50 SMG<EZ,K>
CAP, U 0.01-25
CAP, U 0.01-25
CAP,E 47-25 SMG
C611
C612
C613
C614
C615
87-A12-084-080
87-A12-084-080
87-A12-084-080
87-A12-084-080
87-012-172-080
CAP,E 0.22-50 SMG

CAP,E 0.22-50 SMG
CAP,E 0.22-50 SMG
CAP,E 0.22-50 SMG
CAPACITOR CHIP U 10P CH
C851
C852
C853
C858
C859
87-012-286-080
87-012-286-080
87-012-286-080
87-010-831-080
87-010-831-080
CAP, U 0.01-25
CAP, U 0.01-25
CAP, U 0.01-25
C-CAP,U,0.1-16F
C-CAP,U,0.1-16F<EZ,K>
C616
C617
C618
C620
C623
87-010-221-080
87-010-221-080
87-A12-091-080
87-A12-062-080
87-A12-084-080
CAP, ELECT 470-10V

CAP, ELECT 470-10V
CAP,E 10-50 SMG
CAP,E 100-10 SMG
CAP, ELECT 0.22-50 SMG<EZ>
C860
C869
C870
C871
C872
87-012-286-080
87-012-286-080
87-012-274-080
87-012-199-080
87-012-199-080
CAP, U 0.01-25<EZ,K>
C-CAP,U, 0.01-25<5EZ,4EZ>
C-CAP,U, 1000P-50<5EZ,4EZ>
C-CAP,U, 220P-50<5EZ,4EZ>
C623
C624
C624
C630
C631
87-010-401-080
87-A12-084-080
87-010-401-080
87-A10-260-080
87-012-281-080
CAP, ELECT 1-50V<LH,U,K>

CAP, ELECT 0.22-50 SMG<EZ>
CAP, ELECT 1-50V<LH,U,K>
C-CAP,U 0.1-16 K B
C-CAP,U 3900P-50 B
C873
C874
C875
C876
C877
87-A10-039-080
87-A12-091-080
87-010-759-080
87-A12-091-080
87-012-286-080
CAP, ELECT 10-50 SMG<5EZ,4EZ>
C-CAP,U, 0.1-25F<5EZ,4EZ>
CAP, ELECT 10-50 SMG<5EZ,4EZ>
C-CAP,U, 0.01-25<5EZ,4EZ>
C632
C633
C634
C661
C662
87-012-281-080
87-A11-070-080
87-A11-070-080
87-012-336-080
87-012-336-080
C-CAP,U
C-CAP,U
C-CAP,U
C-CAP,U
C-CAP,U
C878
C879
C901
C904
C905
87-012-184-080
87-012-180-080
87-018-145-080
87-012-286-080
87-012-286-080
CAP,TC-U 6.8P-50 CH<LH,U>
CAP, U 0.01-25<LH,U>
CAP, U 0.01-25<LH,U>
C669
C670
C671
C672
C673
87-012-274-080
87-012-274-080
87-010-759-080
87-010-759-080
87-012-278-080
CHIP CAP,U 1000P-50B<U,EZ,K>

CHIP CAP,U 1000P-50B<U,EZ,K>
C-CAP,U, 0.1-25F<LH>
C-CAP,U, 0.1-25F<LH>
C-CAP,U 2200P-50 B<LH>
C907
C908
C909
C910
C911
87-012-286-080
87-A10-915-080
87-012-286-080
87-012-174-080
87-012-170-080
CAP, U 0.01-25<LH,U>
C-CAP,U 1000P-25 J CH<LH,U>
CAP, U 0.01-25<LH,U>
CAP CHIP CERA SS 12P CHJ<LH,U>
C-CAP,U 8P-50 CH<LH,U>
C677
C771
C772
C779
C780
87-012-286-080
87-A12-062-080
87-012-286-080
87-010-949-080
87-010-949-080
CAP, U 0.01-25
CAP,E 100-10 SMG
CAP, U 0.01-25
C-CAP,S 0.01-50 BJ<EZ,K>
C-CAP,S 0.01-50 BJ<EZ,K>
C912
C913
C914
C915
C916
87-012-195-080
87-012-286-080
87-012-166-080
87-012-174-080
87-012-180-080
C-CAP,U 100P-50CH<LH,U>
CAP, U 0.01-25<LH,U>
C310
C313
C314
C315
C317
87-012-188-080
87-012-284-080
87-012-284-080
87-A12-062-080
87-A12-085-080
C318
C326
C327
C350
C360
87-A12-085-080
87-010-787-080
87-010-831-080
87-012-286-080
87-A12-087-080
C399
C399
C401
C402
C403
3900P-50
0.033-16
0.033-16
330P-50J
330P-50J
B
K B
K B
SL
SL
13
U
U
U
U
U
0.01-25
0.01-25
0.01-25
0.01-25
0.01-25
REF. NO. PART NO.

C917
C918
C921
C922
C940
87-012-186-080
87-A10-039-080
87-012-195-080
87-012-174-080
87-012-286-080
KANRI
DESCRIPTION
NO.
C-CAP,U 470P-50 J CH<LH,U>
C-CAP,U 100P-50CH<LH,U>
CAP, U 0.01-25<EZ,K>
REF. NO. PART NO.
C942
C947
C948
C952
C957
87-012-165-080
87-012-286-080
87-A10-039-080
87-012-286-080
87-012-174-080
CAP 3P-50<EZ,K>
CAP, U 0.01-25<EZ,K>
C-CAP,U 470P-50 J CH<EZ,K>
CAP, U 0.01-25<EZ,K>
C-CAP CERA SS 12P CHJ<EZ,K>
R130
R130
R131
R131
R132
87-A00-257-080
87-A00-262-080
87-A00-257-080
87-A00-262-080
87-A00-257-080
RES,M/F
RES,M/F
RES,M/F
RES,M/F
RES,M/F
C958
C959
C960
C961
C962
87-012-286-080
87-010-831-080
87-010-831-080
87-012-167-080
87-A12-087-080
CAP, U 0.01-25<EZ,K>
C-CAP,U,0.1-16F
C-CAP,U,0.1-16F
CAP,E 1-50 SMG<EZ,K>
R132
R790
R991
R993
R995
87-A00-262-080
87-012-286-080
87-012-195-080
87-012-195-080
87-012-195-080
RES,M/F 0.15-2W J<LH>

CAP, U 0.01-25
C-CAP,U 100P-50CH
C-CAP,U 100P-50CH
C-CAP,U 100P-50CH
C963
C971
C972
C973
C974
87-015-785-080
87-A12-067-080
87-A12-090-080
87-012-286-080
87-012-286-080
CHIP CAPACITOR, 0.1FZ-25Z

CAP,E 330-16 SMG
CAP,E 4.7-50 SMG
CAP, U 0.01-25
CAP, U 0.01-25
SFR451
SFR452
TC942
TH101
TH102
87-A90-432-080
87-A90-432-080
87-A91-774-080
87-A91-042-080
87-A91-042-080
SFR,30K H NVZ6TLTA
SFR,30K H NVZ6TLTA
TRIMMER,PLY30P 6.8X5.4CDYL<EZ,K>
C-THMS,100K 55001
C-THMS,100K 55001
C979
C981
C982
C983
C984
87-012-195-080
87-A12-071-080
87-010-831-080
87-012-286-080
87-012-286-080
C-CAP,U 100P-50CH
CAP,E 47-25 SMG
C-CAP,U,0.1-16F
CAP, U 0.01-25
CAP, U 0.01-25
W99
WH1
X862
X992
8B-NF8-656-010
87-A90-510-010
87-A70-307-010
87-A70-306-010
F-CABLE,7P 2.5 250MM<U,EZ,K>

HLDR,WIRE 2.5-9P
VIB,XTAL 4.332MHZ CSA-309ST<5EZ,4EZ>
VIB,XTAL 4.500MHZ CSA-309ST
C985
C987
C989
C991
C992
87-012-195-080
87-012-286-080
87-012-286-080
87-012-176-080
87-012-176-080
CAP, U 0.01-25
CAP, U 0.01-25<EZ,K>
CAP 15P
CAP 15P
C993
C995
C997
C998
C999
87-012-274-080
87-012-274-080
87-010-831-080
87-A12-071-080
87-A11-155-080

C-CAP,U,0.1-16F
CAP,E 47-25 SMG
CAP,TC U 0.01-16 Z F
C141
C151
C153
C154
C155
87-012-278-080
87-A10-189-040
87-A10-353-080
87-010-785-080
87-012-176-080
C-CAP,U 2200P-50 B
CAP,E 220-10
C-CAP,U 0.22-10KB
C-CAP,U0.015-25BK
CAP 15P
CF831
CF831
CF832
CF832
CN351
87-008-261-010
87-008-423-010
82-785-747-010
87-008-261-010
87-A60-625-010
FILTER, SFE10.7MA5<LH,U>
FLTR,CF,SFE10.7MS3G-A<EZ,K>
CF MS2 GHY R<EZ,K>
FLTR,CF,SFE10.7MA5<LH,U>
CONN,8P V 2MM JMT
C156
C157
C165
C166
C170
87-012-195-080
87-012-198-080
87-012-268-080
87-010-075-040
87-010-759-080
C-CAP,U 100P-50CH
CAP 180P
C-CAP,U 330P-50 B
CAP,E 10-16 5L
C-CAP,U, 0.1-25F
CN501
CN601
CN602
CN605
CN607
87-099-564-010
87-099-750-010
87-A60-131-010
87-A61-108-010
87-099-017-010
CONN,4PVTUC-P4P-B1<LH>
CONN,15P V 9604SC
CONN,6P V FE
CONN,5P V TID-A
CONN, 15P V BLK 6216
C171
C175
C176
C177
C180
87-016-114-080
87-010-759-080
87-012-274-080
87-010-757-080
87-010-759-080
C-CAP,U0.01-25B
C-CAP,U, 0.1-25F
C.CAP,U 0.047-25F
C-CAP,U, 0.1-25F
CNA1
D902
D903
FFC602
FFE831
8B-NF8-652-010
87-A40-128-080
87-A40-128-080
88-906-401-110
A8-6ZA-19H-030
CONN ASSY,7P TID-A(300)<LH>

C-VARI-CAP,HVU202A<LH,U>
C-VARI-CAP,HVU202A<LH,U>
FF-CABLE,6P 1.25
6ZA-1 FEMENM<EZ,K>
C193
C194
C315
C441
C451
87-012-271-080
87-012-195-080
87-010-759-080
87-010-412-040
87-010-067-040
CAP, U 560P-50
C-CAP,U 100P-50CH
C-CAP,U, 0.1-25F
CAP,E 10-25 5L
CAP,E 0.1-50 5L
J203
J602
J831
J832
JR123
87-A60-238-010
87-A60-881-010
87-A60-202-010
87-A60-403-010
87-A10-596-080
TERMINAL,SP 4P (MSC)
JACK,PIN 2P MSP 242V05 PBSN
TERMINAL,ANT 4P<LH,U>
TERMINAL,ANT PAL 2P<EZ,K>
C452
C453
C454
C456
C457
87-010-421-040
87-010-788-080
87-012-273-080
87-010-785-080
87-012-280-080
CAP,E 4.7-50 5L
C-CAP,U 0.033-2.5F
C-CAP,U 820P-50 B
C-CAP,U0.015-25BK
CAP, U 3300P-50
JR124
L201
L202
L451
L801
87-A10-596-080
87-A50-610-010
87-A50-610-010
87-007-342-010
87-A50-608-010
COIL,1UH K(MDEC)
COIL,1UH K(MDEC)
COIL,OSC 85KHZ BIAS
COIL,FM DET-N(TOK)
C459
C460
C621
C622
C623
87-A10-025-080
87-010-831-080
87-010-075-040
87-010-759-080
87-012-188-080
C-CAP,U, 0.22-16ZF
C-CAP,U,0.1-16F
CAP,E 10-16 5L
C-CAP,U, 0.1-25F
C-CAP,U 47P-50 CH
L802
L811
L832
L861
L902
87-A91-551-010
87-005-847-080
87-005-847-080
87-005-847-080
88-ZA1-602-110
FLTR,PCFJZH-450 L(TOK)
COIL,2.2UH K CECS
COIL,2.2UH K CECS
COIL,2.2UH K CECS<5EZ,4EZ>
COIL,FM-RF-U2 2G<LH,U>
C624
C625
C679
C689
CN101
87-012-188-080
87-012-188-080
87-010-759-080
87-010-759-080
87-099-750-010
C-CAP,U 47P-50 CH
C-CAP,U 47P-50 CH
C-CAP,U, 0.1-25F
C-CAP,U, 0.1-25F
CONN,15P V 9604SC
L903
L904
L905
L906
L941
88-ZA1-601-010
87-005-847-080
88-ZA1-624-010
88-ZA1-603-010
87-A50-020-010
COIL,FM-RF-U1 2G<LH,U>
COIL,2.2UH(CECS)<LH,U>
COIL,FM IFT 7-6.2 (COILS)<LH,U>
COIL,FM-OSC-U 2G<LH,U>
COIL,ANT LW(COI)252KHZ<EZ,K>
CN102
CN103
CN121
CN251
CN401
87-099-017-010
87-099-196-010
87-A60-131-010
87-A60-133-010
87-A60-130-010
CONN, 15P 6216

CONN,8P 6216
CONN,6P V FE
CONN,8P V FE
CONN,5P V FE
CN501
CNA141
FFC101
87-A60-586-010
8B-NF8-650-010
88-915-151-110
CONN,4P V FE<LH>
CONN ASSY,2P (35)
FF-CABLE,15P 1.25 150MM
L942
L951
L951
R129
R129
87-A50-019-010
8A-NF8-668-010
8A-NF8-667-010
87-A00-257-080
87-A00-262-080
KANRI
DESCRIPTION
NO.
COIL,OSC LW(COI)856KHZ<EZ,K>
COIL,AM PACK 2(TOK)<EZ,K>
COIL,AM PACK 4(TOK)<LH,U>
RES,M/F 0.15-1W J<U,EZ,K>
RES,M/F 0.15-2W J<LH>
0.15-1W
0.15-2W
0.15-1W
0.15-2W
0.15-1W
J<U,EZ,K>
J<LH>
J<U,EZ,K>
J<LH>
J<U,EZ,K>
FRONT C.B
14
REF. NO. PART NO.
KANRI
DESCRIPTION
NO.
FF-CABLE,15P 1.25 150MM BLACK
REF. NO. PART NO.

R246
R246
WH2
FFC102
FFC103
FFC121
FFC251
FFC401
8B-NF8-655-010
88-908-451-110
88-906-081-110
88-908-451-110
88-905-331-110
FFC501
L151
LCD101
LED140
LED671
88-904-351-110
87-A50-657-010
8B-NF8-601-010
87-A40-317-080
87-A41-053-010
FF-CABLE,4P 1.25<LH>
COIL,CLK 9.43MHZ (TOKO)7KLY
LCD,AIW4272-30P1N
LED,SLR-342VCT31 RED
LED,SMLU18D16CGREEN/UMBER<K,3EZ>
LED671
LED681
LED681
R192
R193
87-A92-077-010
87-A41-053-010
87-A92-077-010
87-010-785-080
87-010-785-080
R194
S306
S307
S308
S309
87-010-785-080
87-A90-095-080
87-A90-095-080
87-A90-095-080
87-A90-095-080
S310
S341
S342
S343
S344
87-A90-095-080
87-A90-095-080
87-A90-095-080
87-A90-095-080
87-A90-095-080
LED,SMLU1BE16C-SLF73BLU/UMB<EXCEPT 3EZ,K>
LED,SMLU18D16CGREEN/UMBER<K,3EZ>
LED,SMLU1BE16C-SLF73BLU/UMB<EXCEPT 3EZ,K>TOP C.B
C-CAP,U0.015-25KB GRM
C190
C191
CN122
S301
SW,TACT EVQ11G04M
S302
SW,TACT EVQ11G04M
SW,TACT EVQ11G04M<5EZ,4EZ>
S303
S304
S305
SW163
SW,TACT EVQ11G04M
SW,TACT EVQ11G04M
SW,TACT EVQ11G04M
MOT.B
SW,TACT EVQ11G04M
S345
S346
S347
S348
S349
87-A90-095-080
87-A90-095-080
87-A90-095-080
87-A90-095-080
87-A90-095-080
SW,TACT
SW,TACT
SW,TACT
SW,TACT
SW,TACT
SW162
SW162
87-A92-172-010
87-A91-645-010
SW,RTRY EC12E24204-25MM OFF<LH,U,K>

SW,RTRY EC12E24304NON-CLICK<EZ>
KANRI
DESCRIPTION
NO.
87-A00-440-050
RES,220-1/2W J RP
87-A00-441-050
RES,270-1/2W J RP<LH>
87-A90-460-010
HLDR,WIRE 2.5-7P
FAN C.B<LH>
CN402
M401
S401
S402
EVQ11G04M
EVQ11G04M
EVQ11G04M
EVQ11G04M
EVQ11G04M
PT C.B
!
!
C85
CN1
PT1
PT1
PT1
87-010-831-080
87-A61-109-010
8B-NF8-608-010
8B-NF8-606-010
8B-NF8-607-010
C-CAP,U,0.1-16F<EZ,K>
CONN,7P V TID-A<LH>
PT,BNF8-EZK<EZ,K>
PT,BNF8-LH<LH>
PT,BNF8-U
!
!
!
!
!
PT2
PT81
PT81
RY1
RY81
8B-MA6-673-010
8B-MA6-675-010
8B-MA6-671-010
87-A92-058-010
87-A92-072-010
PT,SUB BMA H (VRK)<LH>

PT,SUB BMA E (VRK)<EZ,K>
PT,SUB BMA U (VRK)
RELAY,AC DC12V HRM4-S<LH>
RELAY,AC DC12V HRM3H-S-1POLE
!
!
!
!
!
RY81
S1
T1
T2
T81
87-A91-418-010
87-A90-165-010
87-A60-317-010
87-A60-317-010
87-A60-317-010
RELAY,AC12V G5PA-1-M<EZ,K>
SW,SL 1-2-3 SWS2301<LH>
TERMINAL, 1P MSC<LH>
TERMINAL, 1P MSC<LH>
TERMINAL, 1P MSC<U,EZ,K>
T82
WH81
87-A60-317-010
87-A90-460-010
TERMINAL, 1P MSC<U,EZ,K>
HLDR,WIRE 2.5-7P<U,EZ,K>
C501
C502
C503
CN502
CN503
JACK C.B
C223
C224
C241
CNA5
J201
87-010-176-080
87-010-176-080
87-010-831-080
8B-NF8-653-010
87-A61-480-010
C-CAP,S 680P-50 SL<EZ,K>

C-CAP,S 680P-50 SL<EZ,K>
C-CAP,U,0.1-16F
CONN ASSY,5P TID-A (600)
JACK,DIA6.3 BLK ST W/SW MSC16A
R243
R243
R244
R244
R245
87-A01-001-050
87-A00-440-050
87-A00-440-050
87-A01-001-050
87-A00-439-050
RES,220-1/2W
RES,220-1/2W
RES,220-1/2W
RES,220-1/2W
RES,180-1/2W
J
J
J
J
J
BLT2J<EZ>
RP<LH,U,K>
RP<LH,U,K>
BLT2J<EZ>
RP<K>
R245
R245
R245
R246
R246
87-A00-440-050
87-A00-441-050
87-A01-001-050
87-A01-001-050
87-A00-439-050
RES,220-1/2W
RES,270-1/2W
RES,220-1/2W
RES,220-1/2W
RES,180-1/2W
J
J
J
J
J
RP
RP<LH>
BLT2J<EZ>
BLT2J<EZ>
RP<K>
87-A12-087-080
87-A12-090-080
87-A12-071-080
87-A60-688-010
87-A60-109-010
CAP,E 1-50 SMG

CAP,E 47-25 SMG
CAP,E 47-25 SMG
CONN,4P H GRY TUC-P04X-C1
CONN,2P V S2M-2W
87-012-271-080
87-012-195-080
87-A60-154-010
87-A90-095-080
87-A90-095-080
CAP, U 560P-50
C-CAP,U 100P-50CH
CONN,6P H FE
SW,TACT EVQ11G04M
SW,TACT EVQ11G04M
87-A90-095-080
87-A90-095-080
87-A90-095-080
87-A91-991-010
SW,TACT
SW,TACT
SW,TACT
SW,RTRY
87-A60-130-010
87-045-305-010
87-036-110-010
87-036-110-010
CONN,5P V FE
MOTOR, RF-500TB DC-5V (2MA)
SW,MICRO SPPB62
SW,MICRO SPPB62
EVQ11G04M
EVQ11G04M
EVQ11G04M
REO12303PVB8H
MIC C.B<LH>
C502
C503
C505
C506
C507
87-010-186-080
87-010-112-040
87-010-491-040
87-010-320-080
87-010-545-040
CAP,CHIP 4700P-50
CAP,E 100-16
CAP,E 0.22-50M 5L SRE
CHIP CAP 68P
CAP,E 0.22-50M 11L SME
C508
C510
C511
C512
C513
87-010-544-040
87-010-322-080
87-A12-065-040
87-010-178-080
87-010-196-080
CAP,E 0.1-50 SME

C-CAP,S 100P-50 CH
CAP,E 33-16 SMG
CHIP CAP 1000P
CHIP CAPACITOR,0.1-25
C514
C515
C520
CN551
FB501
87-010-196-080
87-010-178-080
87-010-177-080
87-A60-586-010
87-008-372-080
CHIP CAPACITOR,0.1-25
CHIP CAP 1000P
C-CAP,S 820P-50 SL
CONN,4P V FE
FILTER, EMI BL01 RN1
J501
VR501
87-A61-243-010
87-NB7-602-010
JACK,6.3 BLK MONO W/SW V MSC

VR,RTRY 10KAX1 1 V
CN141
S321
S322
S323
S324
87-009-030-010
87-A90-095-080
87-A90-095-080
87-A90-095-080
87-A90-095-080
CONN,2P
SW,TACT
SW,TACT
SW,TACT
SW,TACT
S325
S326
S327
87-A90-095-080
87-A90-095-080
87-A90-095-080
SW,TACT EVQ11G04M
SW,TACT EVQ11G04M
SW,TACT EVQ11G04M<LH>
CN1
M1
S1
S2
S4
87-A60-079-010
87-A91-825-010
87-036-110-010
87-036-110-010
87-036-110-010
CONN,08P H 9604S-08F
MOT,M09Y/Z
PUSH SWITCH
PUSH SWITCH
PUSH SWITCH
S5
SOL1
87-036-110-010
82-ZM3-628-010
PUSH SWITCH
SOL ASSY,23 SO
KEY C.B
V WHT PH
EVQ11G04M
EVQ11G04M
EVQ11G04M
EVQ11G04M
DECK C.B
15
REF. NO. PART NO.
KANRI
NO.
DESCRIPTION
REF. NO. PART NO.
KANRI
NO.
DESCRIPTION
HEAD C.B
CNA351
8B-NF8-654-010
87-A91-195-110
CONN ASSY,8P (375)

HEAD,RPH KC9142 FPC
CHIP RESISTOR PART CODE
Chip Resistor Part Coding
8 8
A
Figure
Resistor Code
Value of resistor
Chip resistor
L
:A
Resistor Code : A
1.0
0.5
0.35
104
1.6
0.8
0.45
108
1.25
0.45
118
3.2
1.6
0.55
128
Dimensions (mm)
Wattage
1/16W
Type
1005
Symbol
CJ
Tolerance
5%
1/16W
1/10W
1608
2125
5%
5%
CJ
CJ
1/8W
3216
5%
CJ
Form
L
t
W
TRANSISTOR ILLUSTRATION
B
E
E C B
2SA1235F
2SC2714O
2SC3052F
CMBT5401
CMBT5551
CSD1306E
KRA102S
KRA107S
KRC104S
KRC107S
KRC102S-RTK
KRA104S
B C E
E C B
2SA1979O/Y
2SA1980G
2SA1981Y
2SC5343G
2SC5342Y
CC5551
CDA1585BC
CSC4115BC
CSB1370EF
2SB1677
2SB1686
2SD2619
2SD2642
D
G
G
S
S D G
G D S
2SK2937
2SJ460
2SK2541
2SK360E
16
2SK2158
WIRING 1 (MAIN / JACK) <EZ, K>

32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
1
A
B
TO HEAD C . B
C
D
E
(CLK)
F
(VT)
<EZ,K>
H
I
J
K
(CNA 005)
L
M
N
O
P
Q
R
S
T
U
17
SCHEMATIC DIAGRAM _ 1 (MAIN 1 / 2 : AMP SECTION / HEAD) <EZ,K>
18
SCHEMATIC DIAGRAM _ 2 (MAIN 2 / 2 : TUNER SECTION) <EZ,K>
19
WIRING 2 (MAIN / JACK / FAN) <U, LH>

32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
1
A
B
TO HEAD C . B
C
D
TO
(CLK)
F
(VT)
H

I
J
K
L
M
N
O
P
Q
R
S
T
U
20
SCHEMATIC DIAGRAM _ 3 (MAIN 1 / 2 : AMP SECTION / HEAD) <U,LH>
21
SCHEMATIC DIAGRAM _ 4 (MAIN 2 / 2 : TUNER SECTION) <U,LH>
22
SCHEMATIC DIAGRAM _ 3 (JACK)
23
WIRING 3 (FRONT) <1 / 2>

1
10
11
12
13
14
15
16
17
24
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
WIRING 3 (FRONT) <2 / 2>

31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
1
A
B
STBY-LED
C
D
TP7 (K-SCAN)
E
F
G
H
TP8(GND)
I
J
K
STBY-LED
L
M
N
O
FFC 501
32
P
Q
R
S
TO DECK C . B
CN 1
T
U
25
WIRING 4 (TOP / MOTOR / MIC / KEY)

32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
1
A
B
C
D
E
F
G
H
I
(FFC 501)
<BLK>
<RED>
J
K
L
M
N
O
P
Q
R
S
M 401 (MOTOR)
T
U
26
SCHEMATIC DIAGRAM _ 5 (FRONT / TOP / KEY / MOT / MIC / DECK )
27
WIRING 5 (PT) <U, EZ, K>

15
14
13
12
11
10
1
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
28
SCHEMATIC DIAGRAM _ 6 (PT) 
29
SCHEMATIC DIAGRAM _ 7 (PT) <EZ,K>
30
WIRING 6 (PT) <LH>

15
14
13
12
11
10
1
A
B
C
D
E
F
G
H
I
<WHT>
J
K
L
M
N
O
P
Q
R
S
T
U
31
SCHEMATIC DIAGRAM _ 8 (PT) <LH>
32
WIRING 7 (DECK / HEAD)

15
14
13
12
11
10
1
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
33
IC BLOCK DIAGRAM
34
LCD DISPLAY
LCD, AIW4272 - 30PIN
SEGMENT WIRING
COMMON WIRING
35
IC DESCRIPTION
IC, LC877256A-5V18 <U,LH,G3EZ,K> / IC, LC877264V-5V24 <4EZ,5EZ>
Pin No.
Pin Name
I/O
Description
O-CD CLK
CD IC control clock output.
O-LEDSTB
STB signal make clock and data effective.
O-DATA
Data output.
O-CLK
Clock output.
O-CDDATA
CD IC control data output.
O-INI-SCAN
Initial scan output.
O-POWER
Power control ON/OFF output.
I-DRF/I-STEREO
RF (radio frequency) detect/Tuner stereo detect input.
I-RDSDATA
RDS IC data input <G4EZ,G5EZ only>.
10
O-STB
11
RES
Reset input for MICON.
12
I-JOG
Dial jog rotary encoder input .
13
I-VOL
Volume rotary encoder input.
14
VSS1
15
CF1
Oscillator circuit input.
16
CF2
Oscillator circuit output.
17
VDD1
Digital power supply pin.
18
I-HOLD
Power failure detected input.
19
I-KEY1
Key A/D input 1.
20
I-KEY2
Key A/D input 2.
21
I-KEY3
Key A/D input 3.
22
SPEANA-L
Spectrum analyser BPF switching control L output.
23
SPEANA-M
Spectrum analyser BPF switching control M output.
24
SPEANA-H
Spectrum analyser BPF switching control H output.
25
I-TU-SIG/I-MIC
Tuner signal input <G4EZ,G5EZ only>/MIC input (Not used).
26
I-CDSW
CD mehca switch input.
27
I-RDSCLK/I-WRQ
RDS IC clock input <G4EZ,G5EZ only>/CD WRQ input.
28
I-TM-BASE
Reference clock input for timer switch.
29
I-RMC
System remote control signal input. "L" : ACTIVE
30 ~ 43
O-S1 ~ O-S14
LCD segment S1 ~ S14 output.
44
I-VF/O-S15
I/O
Not used/LCD segment S15 output.
45
I-KEYCON/O-S16
I/O
K-CON select diode input (Not used)/LCD segment S16 output.
46
I-ECO-OFF/O-S17
I/O
ECO-OFF data input <U,LH only>/LCD segment S17 output.
47
I-AM9K/10K/O-S18
I/O
AM9K/10Kselect diode input <U,LH only>/LCD segment S18 output.
48
I-KARAOKE/O-S19
I/O
Karaoke diode input <LH only>/LCD segment S19 output.
49
I-SW/O-S20
I/O
SW diode input (Not used)/LCD segment S20 output.
50
I-LW/O-S21
I/O
LW diode input <EZ,K only>/LCD segment S21 output.
51
I-RDS/O-S22
I/O
RDS input to diode <G4EZ,G5EZ only>/LCD segment S22 output.
52
I-DEMO/O-S23
I/O
Demo (on the stop) diode input (Not used)/LCD segment S23 output.
53
I-BU2099/O-S24
I/O
Not used/LCD segment S24 output.
54
VDD2
55
VSS2
Connected to ground.
Not used.
36
Pin No.
Pin Name
I/O
56 ~ 79
O-S25 ~ O-S48
LCD segment S25 ~ S48 output.
Description
80
I-CST2
DECK cassette detection switch data input. "L" : ON
81
I-REB
DECK side B recordable switch. "L" : REC
82
I-CAM2
DECK CAM switch data input. "L" : ON
83 ~ 86
O-COM1 ~ O-COM4
LCD driver common.
87
I-AUTO2
DECK AUTO STOP switch data input.
88
I-REA
DECK side A recordable switch. "L" : REC
89
VSS3
90
VDD3
91
O-SOL
DECK solenoid output.
92
O-STBYLED
Standby LED ON/OFF output. "L" : ON
93
I-SUBQ
SUB-Q data input.
94
I-DISH
CD turnable photo sensor input.
95
I-SW2
Window position detection SW2.
96
I-SW1
Window position detection SW1.
97
I-TU-IFC
Tuner IF count input.
98
I-HP-MUTE
Head phone jack detection. "L" : MUTE (Not used)
99
O-PLL CE
Tuner PLL IC chip enable output.
100
O-CD CE
CD data chip enable output.
37
ADJUSTMENT <TUNER / DECK / FRONT>

< TUNER SECTION >
< DECK SECTION >
1. Clock Frequency Check

Settings : Test point : TP2 (CLK)
Method : Set to AM 1710kHz (U,LH), MW 1602kHz (EZ,K) and
check that the test point is 2160kHz 45Hz (U,LH),
2052kHz 45Hz (EZ,K)
1. Tape Speed Check

Settings : Test tape : TTA100
Test point : TP5 (Lch), TP6 (Rch)
Method : Play back the test tape and check that the frequency
counter reads 3000Hz 5Hz (FWD) and 45Hz (REV)
with respect to forward speed.
2. AM/MW VT Check
Settings : Test point : TP1 (VT)
Method : Set to AM 1710kHz (U,LH), MW 1602kHz (EZ,K) and
check that the test point is less than 8.5V (U,LH), less
than 8.0V (EZ,K). Then set to AM 530kHz (U,LH), MW
531kHz (EZ,K) and check that the test point is more than
0.6V.
3. AM/MW Tracking Adjustment
Settings : Test point : TP5 (Lch), TP6 (Rch)
Adjustment location : L951 (1/3)
Method : Set to AM 1000 kHz (U,LH), MW 999kHz (EZ,K) and
adjust L951 (1/3) so that the test point
becomes maximum.
4. LW VT Adjustment<EZ,K>
Settings: Test point :TP1 (VT)
Ajustment location : L942
Method : Set to LW 144kHz and adjust L942 so that the test point
becomes 1.3V 0.05V.
Then set to LW 290kHz and check that the test point is
less than 8.0V.
5. LW Tracking Ajustment<EZ,K>
Settings : Test point :TP5 (Lch),TP6 (Rch)
Ajustment location :
L941................................144kHz
TC942..............................290kHz
Method: Set up TC942 to center before adjustment. The level at
144kHz is adjusted to maximum by L941. Then the level
at 290kHz is adjusted to maximum by TC942.
6. FM VT Check
Settings : Test point : TP1 (VT)
Method : Set to FM 108.0MHz and check that the test point is
less than 8.0V then set to FM 87.5MHz and check that
the test point is more than 0.5V.
2. Head Azimuth Adjustment

Adjustment location : Head azimuth
adjustment screw
Method : Play back (FWD) the 8kHz signal of the test tape
and adjust screw so that the output becomes maximum.
Next, perform on REV PLAY mode.
3. PB Frequency Response Check
Test point :TP5 (Lch), TP6 (Rch)
Method : Play back the 315Hz and 8kHz signals of the test
tape and check that the output ratio of the 8kHz
signal with respect to that of the 315Hz signal is
0dB 3dB.
4. PB Sensitivity Check
Test point :TP5 (Lch), TP6 (Rch)
Method : Play back the test tape and check that the output level of
the test point is 110mV 30mV.
5. REC/PB Frequency Response Adjustment
Adjustment location : SFR 451,SFR452
Input signal : 8kHz/1kHz (LINE IN)(-20VU)
Method : Apply a 1kHz signal and REC mode. Then adjust
OSC attenuator so that the output level at the TP5,
TP6 becomes 10mV. Record and play back the 1kHz
and 8kHz signal and adjust SFRs so that the output of
the 8kHz signals is 0dB 1dB with respect to that of the
1kHz signal.
6. REC/PB Sensitivity Check
Input signal : 1kHz (LINE IN)(0VU)
Method : Apply a 1kHz signal and REC mode. Then adjust
OSC attenuator so that the output level at TP5, TP6
becomes 100mV. Record and play back the 1kHz
signals and check that the output is 1dB 3.5dB.
7. FM Tracking Adjustment<U,LH>
Adjustment location : L903
Method : Set to FM 87.5 MHz and adjust L903 so that the test
point is less than 9.0dBV.
8. FM Tracking Check<EZ,K>
Method : Set to FM 98.0MHz and check that the test point is less
than 13.0dBV.
< FRONT SECTION >

1. -CON OSC Adjustment
Settings : Test point : TP7 (K-SCAN) and TP8 (GND)
Method : Insert AC plug while pressing TUNER function key and
POWER key. Adjust L151 so that the frequency at the
test point is 97.28Hz 0.10Hz.
9. AM IF Adjustment
Adjustment location :
L802..............................450kHz
10. DC Balance / Mono Distortion Adjustment
Settings : Test point : TP3, TP4 (DC Balance)
: TP5 (Lch), TP6 (Rch) (Distortion)
Input level : 60dBV
Method : Set to FM 98.0MHz and adjust L801 so that the voltage
between TP3 and TP4 becomes 0V 300mV.
Then check that the distortion is less than 1.2%.
38
CD TEST MODE
1. How to Start the CD Test Mode
While pressing the FUNCTION button, insert the AC plug to the power outlet.
When the test mode is started, the message [TEST] is displayed.
2. How to Exit the CD Test Mode

Press the POWER button or disconnect the AC plug.
3. Function Descriptions and Application of the CD Test Mode

No
Mode
Start mode
Operation
Display
Function
All indicators light All FL indicators light
Checking item
FL check
Microprocessor check
Search
STOP
mode
button
CD
LD illuminates all the time
APC circuit check
Focus search continuous
Laser current measurement
operations *1
Focus search waveform check
Spindle motor continuous kick Focus error waveform check

(DRF in the search mode is
ignored)
3
Play mode Play button
Normal
Normal playback
Each servo circuit is checked
If TOC cannot be read, focus
DRF check
search is continued
4
Traverse
PAUSE
mode
button
Normal
Tracking servo OFF/ON
Tracking balance check
Each time PAUSE button is

pressed, the tracking servo
repeats turning OFF/ON
Sled mode FF button
TEST
Pickup moves to the inner

circumference *2
Sled circuit check

Tracking circuit check
At the same time, lens kicks to Mechanism operation check

the inner circumference
RWD button
TEST
Pickup check
Pickup moves to the outer

circumference *2
At the same time, lens kicks to
the outer circumference
Spindle
REC button All indicators light The spindle motor rotates
Spindle circuit
forward (rough speed) by
Spindle motor
mode
pressing the button and

rotates backward by pressing
one more time and stops by
pressing again
7
RF AGC
TUNER/
AGC ON/OFF
mode
BAND
button is pressed, the AGC
button
repeats ON/OFF
Each time the TUNER
PU good/faulty check
RF AMP circuit check
*1: The driver IC heats up and the protection circuit starts working when the focus search is continued for 10 minutes or longer.
There can be a case that operations can not be performed correctly.
In such a case, turn off the main power. After cooling down the machine, restart the machine.
*2: Be careful not to damage the gear because the sled motor rotates while the FF or RWD button is being pressed even if the
pick-up is located in the innermost track or the outermost track.
39
4. Displaying the Adjustment Result of the Automatic Adjustment Items

The automatic adjustment values of the focus and tracking adjustment can be displayed on the screen.
4-1. Displaying the automatic adjustment result for the focus offset cancel and gain
1. Select the Start mode. ( All lights are turned on.)
2. Press the TAPE button until the display F*** appears, and decide whether to display the automatic adjustment value or
not.
To display the automatic adjustment value, set 1. If not, set 0.
* * *
OFFSET BIAS GAIN

3. Press the PLAY button to play CD.
4. Press the CD button.
5. An automatic adjustment value is shown as F****** on the display.
(When 0 is selected for all items in step 2 of 4-1, no value is shown.)
** ** **
OFFSET BIAS GAIN

6. After the confirmation is completed, press CD twice button and the mode returns to the PLAY mode.
4-2. Displaying the automatic adjustment result of the tracking offset cancel, balance and gain
1. Select the Start mode. ( All lights are turned on.)
2. Press the VIDEO/AUX button until the display T*** is shown, and decide whether to display the automatic adjustment
value or not.
To display the automatic adjustment value, set 1. If not, set 0.
* * *
OFFSET
GAIN
BALANCE
3. Press the PLAY button to play CD.
4. Press twice the CD button.
5. The automatic adjustment value is shown as T****** on the display.
(When 0 is selected for all items in step 2 of 4-1, no value is shown.)
** ** **
OFFSET
GAIN
BALANCE
6. After the confirmation is completed, press the CD button and the mode returns to PLAY mode.
Note: The automatic adjustment value can be shown but cannot be changed.
40
MECHANICAL EXPLODED VIEW 1 / 1 <U,LH,K>

J
U--- 1 2 3
2
3
K--PWB
A
LH
BZM-1
PLATE,EARTH
MECHA
E
39
22
HT-SINK,FIN2
23
HT-SINK,FIN2
52
62
E
A
HLDR,
HT-SINK
24
A
PWB
LH
32
31
27
38
28
20
25
9
e
a
53
11
PWB
29
10
A
PWB
F
K
42
A
MOT
59
c
A
A
LH
60
36
12
PWB
A WIRE,
HT-SINK, BINDER
FIN2
LH
37
58
FL
A 34 35
62
41
41
A
HT-SINK,
33 56 MAIN U
I
c
56
40
26
30
25
PWB
50
CHAS,MAIN U
LH
48
W 4.2-6.8-0.18
43
54 55
45
B
13
61
15
47
49
46
57
LH
C
D
18
44
14
PLATE,EARTH MIC
51
A
21
16
BZG-5
W 4.2-6.8-0.18
E
C
1
17
PWB
CABI,BOTTOM
19 LH
PWB
I
41
MECHANICAL PARTS LIST 1 / 1 <U,LH,K>
REF. NO. PART NO.

1
2
2
2
3
8B-NF8-008-010
8B-NF8-113-010
8B-NF8-112-010
8B-NF8-111-010
8B-NF8-082-110
KANRI
DESCRIPTION
NO.
PANEL,TRAY
WINDOW,ASSY K GR G5<G5K>
WINDOW,ASSY LH GR G3<G3K>
WINDOW,ASSY U BL G3<LH,U>
PANEL,LEFT
4
5
5
6
6
8B-NF8-014-010
8B-NF8-011-010
8B-NF8-027-010
8B-NF8-057-010
8B-NF8-061-010
6
7
8
9
10
REF. NO. PART NO.
KANRI
DESCRIPTION
NO.
PANEL,TOP
HLDR,TR S
HLDR,PWB PT<U,K>
HLDR,PWB PT 85S<LH>
CABI,REAR K1SM G3<G3K>
39
40
41
41
42
8B-NF8-081-010
8B-NF9-211-010
8A-NF9-208-010
8A-NF7-225-010
8B-NF8-093-010
KNOB,RTRY VOL
RING,VOL<EXCEPT LH,U>
RING,VOL U<LH,U>
CABI,FR EZ<K>
CABI,FR LH DINA<LH>
42
42
42
43
44
8B-NF8-094-010
8B-NF8-088-010
8B-NF8-086-010
87-A91-751-010
8B-NF8-040-010
CABI,REAR K1SM G5<G5K>

CABI,REAR LHSM G3<LH>
CABI,REAR USM G3
FAN,DSB0812M-S382 -400MM<LH>
PLATE,DISP H<LH>
8B-NF8-001-010
8B-NF8-223-010
8B-NF8-030-010
8B-NF8-206-010
8B-NF8-207-010
CABI,FR U
SPR-T,FLAP
PANEL,FLAP
HLDR,PWB L
HLDR,PWB R
44
45
46
46
47
8B-NF8-013-010
8B-NF8-015-010
87-085-185-010
87-A91-422-010
87-A80-157-010
PLATE,DISP U<U,K>
KNOB,RTRY JOG
BUSHING, AC CORD (E)<EXCEPT U>
BUSHING,AC CORD(U)
AC CORD ASSY,E BLK CC<EXCEPT U>
11
12
13
13
14
8B-NF8-016-010
8B-NF8-026-010
8B-NF8-037-010
8B-NF8-036-010
8B-NF8-041-110
KEY,POWER
KEY,ENTER
KEY,KARAOKE<LH>
KEY,OPE<U,K>
KEY,FUNCTION
47
48
49
50
51
87-A80-149-010
88-915-151-110
88-905-331-110
88-906-081-110
88-906-401-110
AC CORD ASSY,U BLK

FF-CABLE, 5P 1.25 330MM
FF-CABLE,6P 1.25
15
15
16
17
18
8B-NF8-019-010
8B-NF8-034-010
8B-NF8-210-010
8B-NF8-025-010
8B-NF8-029-010
KEY,ASSY OPEN/CLOSE<EXCEPT U,LH>

KEY,ASSY OPEN/CLOSE U<LH,U>
KEY,CD
BTN,CD
LENS,SENSOR
52
53
54
55
8B-NF8-654-010
8B-NF8-204-010
8B-NF8-655-010
88-908-451-110
CONN ASSY,8P (400)

COVER, LCD
19
20
21
22
23
8B-NF8-031-010
8B-NF8-203-010
8B-NF8-083-110
8B-NF8-219-010
8B-NF8-218-010
KNOB,RTRY MIC<LH>
GUIDE,LCD
PANEL,RIGHT
HLDR,WINDOW
HLDR,MECH LEFT
56
57
58
59
60
87-064-185-010
88-904-351-110
8B-NF8-051-010
87-A90-457-010
8B-NF8-238-010
HLDR,WIRE
FF-CABLE, 4P 1.25<LH>
REFLECTOR,LCD
F-BEAD,15-25-15 E251<K>
RING,SHLD MOT
24
25
26
27
28
8B-NF8-216-110
8B-NF8-224-010
8B-NF8-209-010
8B-NF8-220-010
8B-NF8-225-010
HLDR,MECH BOTTOM
ROLLER,CASS
BOX ASSY,CASS
LEVER,EJECT
SPR-E,EJECT
61
62
62
A
B
8B-NF8-650-010
8B-NF8-656-010
8B-NF8-652-010
87-067-703-010
87-067-579-010
CONN ASSY,2P(35)
F-CABLE,7P 2.5 250MM<U,K>
CONN ASSY,7P TID-A<LH>
TAPPING SCREW, BVT2+3-10
29
30
31
32
33
8B-NF8-222-010
8B-NF8-213-010
8B-NF8-215-010
8B-NF8-212-010
8B-NF8-217-010
SPR-T,CASS
GEAR,RELAY WINDOW
GEAR,WINDOW
GEAR,CASS CAM
HLDR,MECH RIGHT
C
D
E
F
G
87-591-094-410
87-721-097-410
88-AR1-217-010
87-067-975-010
87-067-689-010
TAPPING SCREW, QIT+3-6

QT2+3-12 GLD
S-SCREW,BFT2+3-8
S-SCREW,IT+4-8
TAPPING SCREW, BVTT+3-8<LH>
34
35
36
37
38
84-ZG1-207-010
84-ZG1-209-010
8B-NF8-221-010
8B-NF8-214-010
84-ZG1-267-010
PULLEY,RELAY
BELT,SQ1.8-117.7
LEVER,SW
GEAR,RELAY
PULLEY,LOAD MO 8
H
I
J
87-067-688-010
87-067-641-010
87-NF4-224-010
BVTT+3-6
UTT2+3-8(W/O SLOT)BL
S-SCREW,IT3B+3-8 CU
!
!
COLOR NAME TABLE

Basic color symbol
Color
Basic color symbol
Color
Basic color symbol
Color
B
Black
C
Cream
D
Orange
G
Green
H
Gray
L
Blue
LT
Transparent Blue
N
Gold
P
Pink
R
Red
S
Silver
ST
Titan Silver
T
Brown
V
Violet
W
White
WT
Transparent White
Y
Yellow
YT
Transparent Yellow
LM
Metallic Blue
LL
Light Blue
GT
Transparent Green
LD
Dark Blue
DT
Transparent Orange
GM
Metallic Green
YM
Metallic Yellow
DM
Metallic Orange
PT
Transparent Pink
LA
Aqua Blue
GL
Light Green
HT
Transparent Gray
42
MECHANICAL EXPLODED VIEW 1 / 1 <EZ>

65
PLATE,EARTH
MECHA
BZM-1
PWB
42
24
d
A
25
E
A
HLDR,
HT-SINK
26
A
WIRE,
BINDER
55
A A
56
HT-SINK,FIN2
HT-SINK,
MAIN U
48
WIRE,
BINDER
I
43
HLDR TR S
27
28
A
32
c
e
29
35
I
34
33
H
WIRE,
BINDER
36
30
60
57
37
44
27
61
40
62
31
9
A
7
e
a
SH,LCD
12
10
a
8
PWB
LCD
A
A
PWB
51
A
b
59
38
13
PWB
23
A
58
39
PWB
41
CHAS,MAIN U
49
50 54
11
B
14
46
M
52
16
C
D
22
45
53
47
15
21
17
BZG-5
A
18
E
C
1
64
19
20
PWB
CABI,BOTTOM EZ
6
A
PWB
I
63
43
MECHANICAL PARTS LIST 1 / 1 <EZ>
REF. NO. PART NO.

1
2
2
2
3
8B-NF8-008-010
8B-NF8-112-210
8B-NF8-116-210
8B-NF8-115-210
8B-NF8-013-010
KANRI
DESCRIPTION
NO.
PANEL,TRAY
WINDOW,ASSY LH GR G3<3EZ>
WINDOW,ASSY EZ BL G5<5EZ>
WINDOW,ASSY EZ BL G4<4EZ>
PLATE,DISP U
4
5
5
6
6
8B-NF8-014-010
8B-NF8-011-010
8B-NF8-027-010
8B-NF8-057-110
8B-NF8-056-110
KNOB,RTRY VOL
RING,VOL<3EZ>
RING,VOL U<5EZ,4EZ>
CABI,FR EZ<3EZ>
CABI,FR EZ-R<5EZ,4EZ>
7
8
9
10
11
8B-NF8-223-010
8B-NF8-030-010
8B-NF8-206-110
8B-NF8-207-210
8B-NF8-015-010
12
13
14
15
16
REF. NO. PART NO.
KANRI
DESCRIPTION
NO.
MOTOR, RF-500TB DC-5V (2MA)
PANEL,TOP
HLDR,PWB PT
CABI,REAR EZ1SM G3<3EZ>
CABI,REAR EZSM G5<5EZ>
41
42
43
44
44
87-045-305-010
8B-NF8-081-110
8A-NF9-208-010
8B-NF8-089-010
8B-NF8-091-010
44
45
46
47
48
8B-NF8-090-010
87-085-185-010
87-A80-157-010
8B-NF8-083-110
8B-NF8-082-210
CABI,REAR EZSM G4<4EZ>

BUSHING, AC CORD (E)
AC CORD ASSY,E BLK CC
PANEL,RIGHT
PANEL,LEFT
SPR-T,FLAP
PANEL,FLAP
HLDR,PWB L
HLDR,PWB R
KNOB,RTRY JOG
49
50
51
52
53
88-915-151-110
8B-NF8-655-010
88-906-081-110
88-905-331-110
88-906-401-110

FF-CABLE, 5P 1.25 330MM
FF-CABLE,6P 1.25
8B-NF8-016-010
8B-NF8-026-010
8B-NF8-036-010
8B-NF8-041-110
8B-NF8-019-110
KEY,POWER
KEY,ENTER
KEY,OPE
KEY,FUNCTION
KEY,ASSY OPEN/CLOSE<3EZ>
54
55
56
57
58
88-908-451-110
8B-NF8-654-010
8B-NF8-656-010
87-064-185-010
87-A90-457-010

CONN ASSY,8P (400)
F-CABLE,7P 2.5 250MM
HLDR,WIRE
F-BEAD,15-25-15 E251
16
17
18
19
20
8B-NF8-034-110
8B-NF8-076-010
8B-NF8-077-010
8B-NF8-078-010
8B-NF8-025-110
KEY,ASSY OPEN/CLOSE U<5EZ,4EZ>

BTN,CD 1
BTN,CD 2
BTN,CD 3
BTN,CD DISC CHANGE
59
60
61
62
63
8B-NF8-238-010
8B-NF8-608-010
8B-NF8-204-010
8B-NF8-203-110
8B-NF8-035-010
RING,SHLD MOT
PT,BNF8-EZK
COVER, LCD
GUIDE,LCD
KEY,RDS<5EZ,4EZ>
21
22
23
24
25
8B-NF8-210-110
8B-NF8-029-010
8B-NF8-051-010
8B-NF8-219-010
8B-NF8-218-110
KEY,CD
LENS,SENSOR
REFLECTOR,LCD
HLDR,WINDOW
HLDR,MECH LEFT
64
65
A
B
C
87-A90-460-010
87-A90-510-010
87-067-703-010
87-067-579-010
87-591-094-410
HLDR,WIRE 2.5-7P
HLDR,WIRE 2.5-9P
TAPPING SCREW, QIT+3-6
26
27
28
29
30
8B-NF8-216-210
8B-NF8-224-010
8B-NF8-209-110
8B-NF8-220-010
8B-NF8-225-010
HLDR,MECH BOTTOM
ROLLER,CASS
BOX ASSY,CASS
LEVER,EJECT
SPR-E,EJECT
D
E
F
G
H
87-721-097-410
88-AR1-217-010
87-067-975-010
87-067-689-010
87-067-688-010
QT2+3-12 GLD
S-SCREW,BFT2+3-8
S-SCREW,IT+4-8
TAPPING SCREW, BVTT+3-8
BVTT+3-6
31
32
33
34
35
8B-NF8-222-010
8B-NF8-213-110
8B-NF8-215-010
8B-NF8-212-110
8B-NF8-217-010
SPR-T,CASS
GEAR,RELAY WINDOW
GEAR,WINDOW
GEAR,CASS CAM
HLDR,MECH RIGHT
I
J
K
L
M
87-B10-091-010
87-NF4-224-010
87-721-096-410
87-067-747-010
82-NE8-215-010
UTT2+3-10 W/O BLK

S-SCREW,IT3B+3-8 CU
QT2+3-10 GLD
W,4.3-14-1
W 4.2-7-0.18
36
37
38
39
40
84-ZG1-207-010
84-ZG1-209-010
8B-NF8-221-010
8B-NF8-214-010
84-ZG1-267-010
PULLEY,RELAY
BELT,SQ1.8-117.7
LEVER,SW
GEAR,RELAY
PULLEY,LOAD MO 8
COLOR NAME TABLE

Basic color symbol
Color
Basic color symbol
Color
Basic color symbol
Color
B
Black
C
Cream
D
Orange
G
Green
H
Gray
L
Blue
LT
Transparent Blue
N
Gold
P
Pink
R
Red
S
Silver
ST
Titan Silver
T
Brown
V
Violet
W
White
WT
Transparent White
Y
Yellow
YT
Transparent Yellow
LM
Metallic Blue
LL
Light Blue
GT
Transparent Green
LD
Dark Blue
DT
Transparent Orange
GM
Metallic Green
YM
Metallic Yellow
DM
Metallic Orange
PT
Transparent Pink
LA
Aqua Blue
GL
Light Green
HT
Transparent Gray
44
TAPE MECHANISM EXPLODED VIEW 1 / 1

30
29
40
28
25
26
24
39
31
38
27
20
35
PWB
16
22
33
43
23
21
31
34
36
SH, 1.63-3.2
-0.5 SLT
44
45
1
A
HLDR, MOTOR
18
19
32
A
PLATE, SHLD
M3
17
MOTOR
HLDR, IC
47
12
46
37
13
5
11
10
PWB
15
45
14
42
41
TAPE MECHANISM PARTS LIST 1 / 1
REF. NO. PART NO.

1
2
3
4
5
8Z-ZM1-271-010
82-ZM1-354-010
82-ZM1-234-310
82-ZM1-226-010
82-ZM1-216-510
KANRI
DESCRIPTION
NO.
PULLEY,MOT ZZM-1
BELT,SBU MAIN2 EPDM
FLY-WHL ASSY,L
GEAR,REW
GEAR,REEL
6
7
8
9
10
82-ZM1-221-310
82-ZM1-237-610
82-ZM1-225-210
82-ZM1-224-410
82-ZM3-333-310
11
12
13
14
15
REF. NO. PART NO.
KANRI
DESCRIPTION
NO.
LVR,REC(*)
SPR-T,PINCH R
SPR-T,CAS
SPR-C,BT 2L
LVR,CAS
31
32
33
34
35
82-ZM1-240-110
82-ZM1-259-310
82-ZM1-257-010
86-ZM1-221-010
82-ZM1-242-010
GEAR,CAM(*)
FLY-WHL ASSY,R
GEAR,FR
LVR,FR
SLIP DISK ASSY 2
36
37
38
39
40
82-ZM1-243-010
82-ZM1-338-110
82-ZM3-353-010
82-ZM1-207-910
82-ZM1-314-110
LVR,STOP
BELT,FR 4
SPR-T,HEAD 2
GUIDE,TAPE
PLATE,HEAD
82-ZM1-223-010
82-ZM1-220-210
82-ZM3-616-010
82-ZM1-227-310
82-ZM1-305-210
GEAR,PLAY
GEAR,IDLER
RING MAGNET 4
LVR,TRIG
SPR-E,TRIG 2
41
42
43
44
45
82-ZM1-208-310
87-A91-195-110
82-ZM1-210-110
82-ZM1-222-310
82-ZM1-362-010
HLDR,HEAD
HEAD,RPH KC9142 FPC
GEAR,H T
LVR,PLAY(*)
LEVER,ASSY PINCH RD
16
17
18
19
20
82-ZM1-255-310
82-ZM1-322-010
82-ZM1-358-110
82-ZM3-628-010
82-ZM1-363-010
SPR-E,LVR DIR
SPR-T,FR 60
CHAS ASSY,FPC
SOL ASSY,23 SO
LEVER,ASSY PINCH LD
46
47
A
B
C
86-ZM1-220-010
82-ZM1-219-010
87-251-070-410
87-741-073-410
87-B10-008-010
FELT,DIA 5.3-14-0.8
CLR,REEL SLIP
U+2.6-3
UT2+2.6-6 GLD
W-P,2.08-8-0.4-SLIP
21
22
23
24
25
82-ZM1-258-210
82-ZM1-333-210
86-ZM1-203-010
82-ZM1-266-310
82-ZM1-214-010
SPR-T,PINCH L
PLATE,LINK2
CAP.REEL
LVR,DIR
SPR-T,DIR
D
E
F
G
H
80-ZM6-243-010
82-ZM3-334-010
86-ZM4-206-110
85-ZM3-202-010
82-ZM3-222-010
SH 1.75-3.6-0.5 SLT
PW 2.16-6-0.4
S-SCREW,AZIMUTH L
S-SCREW,TG
S-SCREW,SHILD PLATE
26
27
28
29
30
82-ZM1-269-210
86-ZM1-202-010
82-ZM1-206-910
82-ZM1-219-110
82-ZM1-218-010
SPR-T,BRG
SHAFT,REEL
CHAS,HEAD
SPR-T,LINK
SPR-E,HB
80-ZM6-207-010
V+1.6-7
46
GENERAL SPEAKER DISASSEMBLY INSTRUCTIONS (FOR REFERENCE)

Type.1
Type.4
TOOLS
Insert a flat-bladed screwdriver into the position indicated by the

arrows and remove the panel. Remove the screws of each speaker
unit and then remove the speaker units.
1 Plastic head hammer

2 (() flat head screwdriver
3 Cut chisel
How to Remove the PANEL, FR

Type.2
Remove the grill frame and four pieces of rubber caps by pulling
out with a flat-bladed screwdriver. Remove the screws from hole
where installed rubber caps. Insert a flat-bladed screwdriver into
the position indicated by the arrows and remove the panel. Remove the screws of each speaker unit and then remove the speaker
units.
1.
Insert the (() flat head screwdriver tip into the gap
between the PANEL, FR and the PANEL, SPKR. Tap the
head of the (() flat head screwdriver with the plastic
hammer head, and create the clearance as shown in Fig-1.
2.
Insert the cut chisel in the clearance, and tap the head of
the cut chisel with plastic hammer as shown in Fig-2, to
remove the PANEL, FR.
3.
Place the speaker horizontally. Tap head of the cut chisel

with plastic hammer as shown in Fig-3, and remove the
PANEL, FR completely.
Type.3
Insert a flat-bladed screwdriver into the position indicated by the
arrows and remove the panel. Turn the speaker unit to counterclockwise direction while inserting a flat-bladed screwdriver into
one of the hollows around speaker unit, and then remove the speaker
unit. After replacing the speaker unit, install it turning to clockwise
direction until "click" sound comes out.
Fig-1
Fig-2
Fig-3
How to Attach the PANEL, FR

Attach the PANEL, FR to the PANEL, SPKR. Tap the four
corners of the PANEL, FR with the plastic hammer to fit the
PANEL, FR into the PANEL, SPKR completely.
47
SPEAKER PARTS LIST <SX-G3 (YLSL,YUSL,Y1SL), SX-G4 (YSL)>
REF. NO. PART NO.
KANRI
DESCRIPTION
NO.
PANEL, FR
PANEL, SP
PANEL, BA
PROTECTOR, SP<EXCEPT YSL>
PROTECTOR, SP G<YSL>
1
2
3
4
4
8B-NSZ-001-010
8B-NSZ-002-010
8B-NSZ-003-010
8B-NSZ-004-010
8B-NSZ-009-010
5
5
6
6
7
8B-NSZ-602-010
8B-NSZ-604-010
8B-NSK-604-010
8B-NSK-610-010
87-NS7-611-010
SPKR,W 140 30/4<YLSL>

SPKR,W 140 25/4<EXCEPT YLSL>
SPKR,T 60<YLSL,YUSL>
SPKR,T 60 L<Y1SL,YSL>
CORD,SPKR
8
9
9
10
8B-NSZ-012-010
8B-NSZ-010-010
8B-NSZ-011-010
8B-NSZ-013-010
RING,W
PANEL,DUCT GR<Y1SL>
PANEL,DUCT BL<EXCEPT Y1SL>
PANEL,DUCT B
SPEAKER PARTS LIST (SX-G5) <YML>
REF. NO. PART NO.

1
2
3
4
5
8B-NSS-003-010
8A-NST-614-010
8B-NSS-602-010
8B-NSS-604-010
8B-NSS-007-010
6
7
8B-NSS-008-010
8B-NSS-002-010
KANRI
DESCRIPTION
NO.
GRILLE, FRAME ASSY
TERMINAL
SPKR, W 140 25/2
SPKR, TW ASSY
SPKR, TW
RING, TW
RING, W
ACCESSORIES / PACKAGE LIST
REF. NO. PART NO.

1
1
1
1
1
!
!
KANRI
DESCRIPTION
NO.
8B-NF8-903-010
IB,U(ESF)M
8B-NF8-902-010
IB,LH(ESP)M<LH>
8B-NF8-905-010
IB,K(E)M G3/5/6<K>
8B-NF8-906-010
IB,EZ(9L)M G3<3EZ>
8B-NF8-916-010
IB,EZ(9L)M G4/G4/G6-RDS<4EZ,5EZ>
2 8B-NF8-701-010
2 8B-NF8-706-010
3 87-006-225-010
4 87-043-115-010
4 87-A90-118-010
RC UNIT,RC-BAS03<3EZ,K>
RC UNIT,RC-BAS11<U,LH,4EZ,5EZ>
AM LOOP ANT NC2
ANT,FEEDER FM<U,LH>
ANT,WIR FM(Z)<EZ,K>
5
6
PLUG CONVERSION JT-0476<LH>

PLUG, ADPTR CONV(K)<K>
87-A91-017-010
87-099-811-010
48
211, IKENOHATA 1CHOME, TAITO-KU, TOKYO 110, JAPAN TEL:03 (3827) 3111
2000058 2000045 2000044 0251431 921338
Printed in Singapore

Service Manual: XS-G3 XS-G4 XS-G5

Uploaded by

Copyright:

Available Formats

Service Manual: XS-G3 XS-G4 XS-G5

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Service Manual: XS-G3 XS-G4 XS-G5

Uploaded by

Copyright:

Available Formats

XS-G3

BASIC TAPE MECHANISM : BZM-1 R1NM

S/M Code No. 09-013-441-5R1

If requiring information about the CD mechanisim, see Service Manual of BZG-5,

87.5 MHz to 108 MHz

531 kHz to 1602 kHz (9 kHz step)

<LW tuner section><EZ,K>

144 kHz to 290 kHz

Total harmonic distortion

<Compact disc player section>

2 way, bass reflex (magnetic shielded)

EZ,K: 230 V AC, 50 Hz

Design and specifications are subject to change without notice.

4 tracks, 2 channels stereo

The word "BBE"and the "BBE symbol" are trademarks of BBE

PROTECTION OF EYES FROM LASER BEAM DURING SERVICING

Caution: Invisible laser radiation when

Usynlig laserstling ved bning, nr sikkerhedsafbrydereer

Precaution to replace Optical block

1) After the connection, remove solder shown in

NOTE ON BEFORE STARTING REPAIR

1 Remove the AC power cord.

Select a discharging resistor referring to the following table.

Charging voltage (V)

Rated power (W)

2. Check items before exchanging the MICROCOMPUTER

2-1. Regarding the HOLD terminal of the MICROCOMPUTER

Good or no good judgement of the MICROCOMPUTER

2-2. Regarding reset

2-3. Confirmation of soldering state of MICROCOMPUTER

2) Remove the three screws.

3) Remove the four screws (1) and remove the PANEL,

4) Remove the PANEL, RIGHT.

5) Remove the PANEL, LEFT.

8) Remove the three screws (1) and remove the PWB,

9) Slide up slightly the WINDOW, DISP ASSY (1).

2. INSTRUCTIONS FOR ASSEMBLING MECHANISM

2) Install the HLDR, WINDOW so that the upper end of the

3) Rotate the GEAR, RELAY until the HLDR, WINDOW

1) Turn GEAR RELAY until.

APPLY CFD-409 on the RAIL

2) Engage the gear so that the HDLR.

1) Rotate the GEAR RELAY to open

ELECTRICAL MAIN PARTS LIST

REF. NO. PART NO.

REF. NO. PART NO.

CAP,E 3300-35 M 85 SKR<LH,U>

CAP,E 330-16 SMG<LH,U,K>

CAP,E 470-25 SMG

CAP,E 0.22-50 SMG

CAP,E 10-50 SMG

REF. NO. PART NO.

REF. NO. PART NO.

CAP,E 0.33-50 SMG

C-CAP,U 470P-50 J CH<U,EZ,K>

CAP,E 10-50 SMG

CAP,E 1-50 SMG

CHIP CAP,U 1000P-50B

CAP, CHIP SS 1500 PBK<EZ,K>