Centrifugal Pumps
Centrifugal Pumps
NITISH NAIR
and installation of rigid and flexible flowlines and umbilicals. They design, build and install fixed and floating platforms for the development of oil and gas fields located at water depths ranging from a few meters to nearly 3000 meters. Technip is also a world leader in the engineering and construction of refining and petrochemical units, gas treatment and liquefaction units, as well as in hydrogen, ethylene and synthetic gas production units.
1958 - Technip was founded in paris with a workforce of 100 people. 1960s - First series of international successes with completion of projects in Africa and Asia. 1970s - Technip becomes an international group: opening of an office in Rome and creation of Technip Geoproduction. 1980s - Technip expands its global presence and opens operating centers in Kuala Lumpur and Abu Dhabi. 1990s - Technip is listed on the Paris Stock Exchange. 2000s - Technip becomes a world leader in engineering, technologies and services for the oil and gas industry
equipment in any process plant. Its purpose is to convert energy of a prime mover first into velocity or kinetic energy and then into pressure energy of a fluid that is being pumped.
A centrifugal pump has two main components: A rotating component comprised of an impeller and a
shaft
A stationary component comprised of a casing, casing
1) Impeller The impeller is the main rotating part that provides the centrifugal acceleration to the fluid. They are often classified in many ways.
Based on major direction of flow in reference to the axis of
II.
Closed: Shrouds or sidewall enclosing the vanes. II. Open: No shrouds or wall to enclose the vanes. III. Semi-open or vortex type.
I.
2) Shaft The basic purpose of a centrifugal pump shaft is to transmit the torques encountered when starting and during operation while supporting the impeller and other rotating parts. It must do this job with a deflection less than the minimum clearance between the rotating and stationary parts.
3) Shaft Sleeve Pump shafts are usually protected from erosion, corrosion, and wear at the seal chambers, leakage joints, internal bearings, and in the waterways by renewable sleeves. Unless otherwise specified, a shaft sleeve of wear, corrosion, and erosion resistant material shall be provided to protect the shaft. The sleeve shall be sealed at one end.
4) Coupling Couplings can compensate for axial growth of the shaft and transmit torque to the impeller. Shaft couplings can be broadly classified into two groups: Rigid and Flexible. Rigid couplings are used in applications where there is absolutely no possibility or room for any misalignment. Flexible shaft couplings are more prone to selection, installation and maintenance errors.
Casing Casings are generally of two types: volute and circular. The impellers are fitted inside the casings. I. Volute casings A volute casing is a curved funnel increasing in area to the discharge port. As the area of the cross-section increases, the volute reduces the speed of the liquid and increases the pressure of the liquid. II. Circular Casing It has stationary diffusion vanes surrounding the impeller periphery that convert velocity energy to pressure energy.
1)
Both the seal chamber and the stuffing box have the
primary function of protecting the pump against leakage Both the seal chamber and the stuffing box have the primary function of protecting the pump against leakage. When the pressure at the bottom of the chamber is below atmospheric, it prevents air leakage into the pump. When the pressure is above atmospheric, the chambers prevent liquid leakage out of the pump. The seal chambers and stuffing boxes are also provided with cooling or heating arrangement for proper temperature control.
equipment in any process plant. Its purpose is to convert energy of a prime mover first into velocity or kinetic energy and then into pressure energy of a fluid that is being pumped The energy changes occur by virtue of two main parts of the pump, the impeller and the volute or diffuser
The liquid enters the suction nozzle and then into eye
of revolving device known as impeller. When the impeller rotates, it spins the liquid sitting in the cavities between the vanes outward and provides centrifugal acceleration. As liquid leaves the eye of the impeller a low pressure area is created causing more liquid to flow towards the inlet. Since the impeller blades are curved, the fluid is pushed in a tangential and radial direction by centrifugal force.
centrifugal force is kinetic energy. The amount of energy given to the liquid is proportional to the velocity at the edge or vane tip of the impeller. The faster the impeller revolves or the bigger the impeller is, then the higher will be the velocity of the liquid at the vane tip and the greater the energy imparted to the liquid.
impeller is harnessed by creating a resistance to the flow. The first resistance is created by the pump volute (casing) that catches the liquid and slows it down. In the discharge nozzle, the liquid further decelerates and its velocity is converted to pressure according to Bernoullis principle.
defined with the help of a graph called a system curve. Similarly the capacity vs. pressure variation graph for a particular pump defines its characteristic pump performance curve. The pump suppliers try to match the system curve supplied by the user with a pump curve that satisfies these needs as closely as possible.
the system resistance curve intersect. The intersection of the two curves defines the operating point of both pump and process. However, it is impossible for one operating point to meet all desired conditions. For example, when the discharge valve is throttled, the system resistance curve shift left and so does the operating point.
flow with respect to the head of the system. It must be developed by the user based upon the conditions of service. These include physical layout, process conditions and fluid characteristics. It represents the relationship between flow and hydraulic losses in a system in a graphic form. The system curve is parabolic in curve because the friction losses vary as the square of the flow rate.
performance curve where its capacity i.e. flow rate is plotted against its developed head. The pump performance curve also shows its efficiency, required input power, NPSHr, speed and other information such as pump size and type, impeller size, etc. NPSH stands for net positive suction head which is the excess pressure at the pump suction nozzle over the vapour pressure of the liquid being pumped. It is generated by tests performed by the pump manufacturer.
corresponds to the shut off head point of the pump. The curve then decreases to a point where the flow is maximum and head is minimum. This point is sometimes called the run out point. The pumps range of operation is from the shut off head point to the run out point. Trying to run a pump of the right end of a curve will result in pump cavitation and eventually destroy the pump.
values of total head and flow rate. This curve initially increases and passes through the operating point and then gradually decreases.
to be met all the time for a trouble free operation and a longer service life of centrifugal pumps. The first requirement is that no cavitation of the pump occurs throughout the broad operating range. The second requirement is that a certain minimum continuous flow is always maintained during operations.
Flow regulation
Flow in centrifugal pumps varies widely with system
resistance; hence their flow regulation is low. If the service requires high flow regulation, a displacement pump is the appropriate choice.
Liquid viscosity
Centrifugal pump performance deteriorates rapidly with
increasing viscosity, and a displacement pump is usually the better choice whenever the liquid viscosity exceeds 150 cst.