SHOTCRETING

SHOTCRETING AND
GUNITING
SUBMITTED BY:
RAJAN CHAUAHN
INTRODUCTION
Shotcrete, then known as gunite (/gnt/), was invented in
1907 by American taxidermi Akeley to repair the crumbling
facade of the Field Columbian Museum in Chicago (the old
Palace of Fine Arts from the World's Columbian Exposition.
He used the method of blowing dry material out of a hose with

compressed air, injecting water at the nozzle as it was
released.
In 1911, he was granted a patent for his inventions, the

"cement gun", the equipment used, and "gunite", the material
that was produced.
There is no evidence that Akeley ever used sprayable concrete
in his taxidermy work, as is sometimes suggested. F. Trubee
Davison covered this and other Akeley inventions in a special
issue of Natural History magazine.
Until the 1950s when the wet-mix process was devised, only
the dry-mix process was used.
In the 1960s, The alternative method for gunning by the dry

method was devised with the development of the rotary gun,
with an open hopper that could be fed continuously. Shotcrete
is also a viable means and method for placing structural
concrete.
DEFINITION OF SHOTCRETE
Shotcrete or gunite is a mortar or a fine concrete that is
pneumatically Transported through a hose and projected onto a
surface at a high velocity.
applied mixture of cement, aggregate, and water conveyed
through a hose and projected at high velocity onto the
application surface.
This system is called by different proprietory names in
different countries such as blastcrete, guncrete, jet-crete,
nucrete, spraycrete etc., though the priciple is essentially the
same.
This system is more economical than conventional concrete
because of less formwork requirements, requiring a small
portable plant for manufacture and placement.
The force of the jet impacting on the surface compact the
material.
Sometimes set accelerators are used to assist overhead
placing.
The newly developed redi-set cement can also be used for
shotcreting process.
SHOTCRETE
WATER
Portland ADMIXTURES
(FOR WET SAND
Cement OR FIBRES
PROCESS)
Applied via Compressed Air

SHOTCRETE MATERIALS
Cement, Water, Sand and Aggregate are the basic materials

used in Shotcrete along with variousplasticizers and
admixtures to enhance its functioning.
High Water-Cement ratio gives slow setting and influences

end quality while moisture content in sand/aggregate is also
keenly measured. Optimal W/C ratio is around 0.45.
Composition of Sand/Aggregate depends upon water

demand, workability, accelerators, rebound, shrinkage and
durability.
Super plasticizers for very low W/C ratios and high
workability.
Hydration control admixtures for maintaining workability

from 3 to 72 hours.
Alkali free accelerators for safety and durability.
Micro Silica and Slump retainers.
Addition of steel and high performance polymer fibers and
micro silica slurries.
Hydration stabilizers are used for controlling the hydration of

cements. The addition of Shotcrete accelerators restarts the
hydration process and causes immediate setting.
SHOTCRETE PROCESS
The two basic methods for applying shotcrete are the dry-
mix process and the wet-mix process. The term gunite is
frequently used when referring to the dry-mix method;
other terms such as air-placed concrete, gunned concrete
and sprayed concrete have also been used in the past to
describe the process.
1. DRY-MIX SHOTCRETE(GUNITING)
2. WET-MIX SHOTCRETE
1. DRY-MIX SHOTCRETE(GUNITING)
The cementitious material and aggregate are thoroughly

mixed and either bagged in a dry condition, or mixed and
delivered directly to the gun. The mixture is normally fed to a
pneumatically operated gun which delivers a continuous flow
of material through the delivery hose to the nozzle. The
interior of the nozzle is fitted with a water ring which
uniformly injects water into the mixture as it is being
discharged from the nozzle and propelled against the
receiving surface
STEPS INVOLVED
Step1: Pre blended, dry or semi-dampened materials are placed
into shotcrete equipment and metered into a hose.
Step2: Compressed air conveys materials at high velocity to
the nozzle where the water is added.
Step3: Then the material is consolidated on receiving surface
by high impact velocity.
The dry process can be used for any shotcreting applications
from the smallest patching and sealing works to largest
projects.
The maximum production achievable with dry process
equipment ranges from 10-12 yards per hour of dry mix
depending on the conditions.
Most applications have production rates of 2-6 cubic yards per
hour of mix.
2. WET-MIX SHOTCRETE
The cementitious material, aggregate, water, and admixtures

are thoroughly mixed as would be done for conventional
concrete. The mixed material is fed to the delivery
equipment, such as a concrete pump, which propels the
mixture through the delivery hose by positive displacement
or by compressed air. Additional air is added at the nozzle to
increase the nozzle discharge velocity
STEPS INVOLVED
Step 1: Wet material is pumped to the nozzle where
compressed air is introduced to
Step2: All ingredients, including water, are thoroughly mixed
and introduced into the shotcrete equipment.
provide high velocity for placement and consolidation of the
material onto the receiving surface.
Step 3: Mostly wet-process shotcreting is done with premixed
mortar or small aggregate concrete.
The mix design and consistency of supply are very important
in order to provide a mix with the workability or plasticity to
be pumped through a small-diameter hose.
Sand gradation is same as for the dry process and for coarse
aggregate mixes;20-30 percent of 20mm aggregate is added.
Cement content will vary according to agg.
APPLICATIONS OF SHOTCRETE
Channel linings, protection of bridge abutments and

stabilization of debris-flow prone creeks.
Rehabilitation of reinforced concrete structures such as
bridges ,chemical processing and handling plants.
Rehabilitation of deteriorated marine structures such as
bulkheads, piers, sea
Support of underground openings in tunnel, mines,
drainage audits and exploratory audits.
Rock slope stabilization and support for excavated
foundations, often in conjuction with rock and soil anchor
systems.
SHOTCRETE AS REPAIR TECHNIQUE
Shotcrete can be used to repair the damaged surface of
concrete, wood, or steel structures provided there is access
to the surface needing repair. The following examples
indicate a few ways in which shotcrete can be used in
repairs:
Bridges.
Shotcrete repair can be used for bridge deck
rehabilitation, but it has generally been uneconomical
for major full-thickness repairs.
It is very useful, however, for beam repairs of variable
depths, caps, columns, abutments, wingwalls, and
underdecks from the standpoint of technique and cost.
Buildings.
In building repairs, shotcrete is commonly used for repair
of fire and earthquake damage and deterioration,
strengthening walls, and encasing structural steel for
fireproofing. The repair of structural members such as roof,
beams, columns, and connections is common for structures
damaged by an earthquake.
Marine structures.
Damage to marine structures can result from deterioration
of the concrete and of the reinforcement. Damaging
conditions are corrosion of the steel, freezing and thawing
action, impact loading, structural distress, physical abrasion
from the action of waves, sand, gravel, and floating ice, and
chemical attack due to sulfates. These problems can occur
in most marine structures such as bridge decks, piles, pile
caps, beams, piers, navigation locks, guide walls, dams,
powerhouses, and discharge tunnels. In many cases,
shotcrete can be used to repair the deteriorated surfaces of
these structures.
Spillway surfaces.
Surfaces subject to high velocity flows may be damaged by

cavitation erosion or abrasion erosion.
Shotcrete repairs are advantageous because of the
relatively short outage necessary to complete the repairs
Slope and surface protection.
Shotcrete is often used for temporary protection of exposed
rock surfaces that will deteriorate when exposed to air.
Shotcrete is also used to permanently cover slopes or cuts
that may erode in time or otherwise deteriorate.
Slope protection should be properly drained to prevent
damage from excessive uplift pressure.
Application of shotcrete to the surface of landfills and other
waste areas is beneficial to prevent surface water
infiltration.
ADVANTAGES
Little or no framework is required.

Cost effective method for placing concrete.
Ideal for irregular surfaces application.
Allows for easier material handling in areas with difficult
access.
Easy start up, shutdown and clean up.
An increase in load bearing capacity due to redistribution
of stresses.
Excellent corrosion resistance
DISADVANTAGES
Strong wind will separate the material between the nozzle

and the point of deposit, reducing the strength
Rain may wash out the cement leaving a sandy surface, or
it may saturate the shotcrete and cause sloughing or
sagging
It requires skilled and experienced labours.
A greater degree of geotechnical knowledge is required
Improperly applied shotcrete may create conditions much
worse than the untreated condition
THANK YOU

SHOTCRETING

Uploaded by

Copyright:

Available Formats

SHOTCRETING

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

SHOTCRETING

Uploaded by

Copyright:

Available Formats

SHOTCRETING AND

He used the method of blowing dry material out of a hose with

In 1911, he was granted a patent for his inventions, the

In the 1960s, The alternative method for gunning by the dry

Applied via Compressed Air

Cement, Water, Sand and Aggregate are the basic materials

High Water-Cement ratio gives slow setting and influences

Composition of Sand/Aggregate depends upon water

Hydration control admixtures for maintaining workability

Hydration stabilizers are used for controlling the hydration of

The cementitious material and aggregate are thoroughly

The cementitious material, aggregate, water, and admixtures

Channel linings, protection of bridge abutments and

Surfaces subject to high velocity flows may be damaged by

Little or no framework is required.

Strong wind will separate the material between the nozzle

You might also like